Memorex MX4118 Portable CD Player User Manual

Memorex MX4118 Portable CD Player User Manual
MX4118
User’s Guide
Home Audio System with
CD Player and AM/FM
Stereo Radio
Before operating this product,
please read these instructions completely.
Dear Customer,
Please read this manual thoroughly before operating the unit to become more familiar with it and obtain the
performance that will bring you continued enjoyment for many years. Keep these instructions handy for
future reference.
PLEASE KEEP ALL PACKAGING MATERIAL FOR AT LEAST 90 DAYS IN CASE YOU
NEED TO RETURN THIS PRODUCT TO YOUR PLACE OF PURCHASE OR MEMOREX.
For future reference, record the serial number of the unit printed on the rear of the cabinet.
Serial Number _______________________________________
CAUTION
INFORMATION
This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable
protection against harmful interference in a
residential installation. This equipment generates,
uses and can radiate radio frequency energy and,
if not installed and used in accordance with the
instructions, may cause harmful interference to
radio communications. However, there is no
guarantee that interference will not occur in a
particular installation. If this equipment does
cause harmful interference to radio or television
reception, which can be determined by turning the
equipment off and on, the user is encouraged to
try to correct the interference by one or more of
the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment
and receiver.
• Connect the equipment into an outlet on a circuit
different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV
technician for help.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR BACK). NO
USER-SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
The Caution Marking is located at the rear enclosure of the
apparatus.
DANGEROUS VOLTAGE
The lightning flash with arrowhead symbol,
within an equilateral triangle is intended to alert
the user to the presence of uninsulated
dangerous voltage within the product’s
enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
ATTENTION
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
DANGER:
Invisible and hazardous laser radiation
when open and interlock failed or defeated.
Avoid direct exposure to beam.
FCC WARNING:
This equipment may generate or use radio
frequency energy. Changes or modifications to
this equipment may cause harmful interference
unless the modifications are expressly
approved in the instruction manual. The user
could lose the authority to operate this
equipment if an unauthorized change or
modification is made.
LASER SAFETY: This unit employs a laser.
Only qualified service personnel should attempt
to service this device due to possible eye injury.
CAUTION:
USE
OF
CONTROLS,
ADJUSTMENTS OR PERFORMANCE
PROCEDURE HEREIN MAY RESULT IN
HAZARDOUS RADIATION EXPOSURE.
WARNING: TO PREVENT FIRE OR
SHOCK HAZARD, DO NOT EXPOSE
THIS UNIT TO RAIN OR MOISTURE.
SURGE PROTECTORS:
It is recommended to use a surge protector for AC
connection. Lightning and power surges ARE
NOT covered under warranty for this product.
1
ATTENTION:
POUR ÉVITER LES CHOC ÉLECTRIQUES,
INTRODUIRE LA LAME LA PLUS LARGE DE LA
FICHE DANS LA BORNE CORRESPONDANTE
DE LA PRISES ET POUSSER JUSQU’AU FOND.
Dear Customer:
Selecting fine audio equipment such as the unit you’ve just purchased is only the start of your
musical enjoyment. Now it’s time to consider how you can maximize the fun and excitement your
equipment offers. This manufacturer and the Electronic Industries Association’s Consumer
Electronics Group want you to get the most out of your equipment by playing it at a safe level. One
that lets the sound come through loud and clear without annoying blaring or distortion-and, most
importantly, without affecting your sensitive hearing.
Sound can be deceiving. Over time your hearing “comfort level” adapts to higher volumes of
sound. So what sounds “normal” can actually be loud and harmful to your hearing. Guard against
this by setting your equipment at a safe level BEFORE your hearing adapts.
To establish a safe level:
• Start your volume control at a low setting.
• Slowly increase the sound until you can hear it comfortably and clearly, and without distortion.
Once you have established a comfortable sound level:
• Set the dial and leave it there.
Taking a minute to do this now will help to prevent hearing damage or loss in the future. After all,
we want you listening for a lifetime.
We Want You Listening For A Lifetime
Used wisely, your new sound equipment will provide a lifetime of fun and enjoyment. Since hearing
damage from loud noise is often undetectable until it is too late, this manufacturer and the
Electronic Industries Association’s Consumer Electronics Group recommend you avoid prolonged
exposure to excessive noise. This list of sound levels is included for your protection.
Decibel
Level
30
40
50
60
70
80
Example
Quiet library, soft whispers
Living room, refrigerator, bedroom away from traffic
Light traffic, normal conversation, quiet office
Air conditioner at 20 feet, sewing machine
Vacuum cleaner, hair dryer, noisy restaurant
Average city traffic, garbage disposals, alarm clock at two feet
THE FOLLOWING NOISES CAN BE DANGEROUS UNDER CONSTANT EXPOSURE:
Subway, motorcycle, truck traffic, lawn mower
Garbage truck, chain saw, pneumatic drill
Rock band concert in front of speakers, thunderclap
Gunshot blast, jet engine
Rocket launching pad
Information courtesy of the Deafness Research Foundation.
NI
C
IND
A
EST. 1924
O
O C I A TI
IES
ELECT
TR
EIA
S
S
2
U
S
R
O
N
90
100
120
140
180
We
Want You
LISTENING
For A Lifetime
IMPORTANT SERVICE SAFETY INSTRUCTIONS
Before using the unit, be sure to read all operating instructions
carefully. Please note that these are general precautions and may not
pertain to your unit. For example, this unit may not have the capability
to be connected to an outdoor antenna.
1. READ INSTRUCTIONS
All the safety and operating instructions should be read before the
product is operated.
2. RETAIN INSTRUCTIONS
The safety and operating instructions should be retained for future reference.
3. HEED WARNINGS
All warnings on the product and in the operating instructions should be
adhered to.
4. FOLLOW INSTRUCTIONS
All operating and use instructions should be followed.
5. CLEANING
Unplug this product from the wall outlet before cleaning. Do not use
liquid cleaners or aerosol cleaners. Use a dry cloth for cleaning.
6. ATTACHMENTS
Do not use attachments not recommended by the product's
manufacturer as they may cause hazards.
7. WATER AND MOISTURE
Do not use this product near water–for example: near a bathtub,
washbowl, kitchen sink or laundry tub; in a wet basement; or near a
swimming pool.
8. ACCESSORIES
Do not place this product on an unstable cart, stand, tripod, bracket or
table. The product may fall, causing serious injury and serious damage to
the product. Use only with a cart, stand, tripod, bracket or table
recommended by the manufacturer or sold with the
product. Any mounting of the product should follow the
manufacturer’s instructions, and should use a mounting
accessory recommended by the manufacturer.
8A. An appliance and cart combination should be moved
with care. Quick stops, excessive force and uneven
surfaces may cause the appliance and cart
combination to overturn.
9. VENTILATION
Slots and openings in the cabinet and in the back or bottom are
provided for ventilation, to ensure reliable operation of the product and
to protect it from overheating. These openings must not be blocked or
covered. The openings should never be blocked by placing the product
on a bed, sofa, rug or other similar surface. This product should never
be placed near or over a radiator or heat source. This product should
not be placed in a built-in installation such as a bookcase or rack
unless proper ventilation is provided or the manufacturer's instructions
have been adhered to.
10. POWER SOURCES
This product should be operated only from the type of power source
indicated on the marking label. If you are not sure of the type of power
supply to your home, consult your appliance dealer or local power
company. For products intended to operate from battery power, or
other sources, refer to the operating instructions.
11. GROUNDING OR POLARIZATION
This product is equipped with a polarized alternating-current line plug
(a plug having one blade wider than the other). This plug will fit into the
power outlet only one way. This is a safety feature. If you are unable to
insert the plug fully into the outlet, try reversing the plug. If the plug
should still fail to fit, contact your electrician to replace your obsolete
outlet. Do not defeat the safety purpose of the polarized plug.
12. POWER-CORD PROTECTION
Power-supply cords should be routed so that they are not likely to be
walked on or pinched by items placed upon or against them, paying
particular attention to cords at plugs, convenience receptacles, and the
point where they exit from the appliance.
13. LIGHTNING
To protect your product from a lightning storm, or when it is left
unattended and unused for long periods of time, unplug it from the wall
outlet and disconnect the antenna or cable system. This will prevent
damage to the product due to lightning and power-line surges.
14. POWER LINES
An outside antenna system should not be located in the vicinity of
overhead power lines or other electric light or power circuits, or where it
can fall into such power lines or circuits. When installing an outside
antenna system, extreme care should be taken to keep from touching
such power lines or circuits as contact with them might be fatal.
15. OVERLOADING
Do not overload wall outlets and extension cords as this can result in a
risk of fire or electric shock.
16. OBJECT AND LIQUID ENTRY
Never push objects of any kind into this product through openings as they
may touch dangerous voltage points or short out parts that could result in
fire or electric shock. Never spill or spray any type of liquid on the product.
17. OUTDOOR ANTENNA GROUNDING
If an outside antenna is connected to the product, be sure the antenna
system is grounded so as to provide some protection against voltage
surges and built-up static charges. Section 810 of the National Electric
Code, ANSI/NFPA 70, provides information with respect to proper
grounding of the mast and supporting structure, grounding of the leadin wire to an antenna discharge product, size of grounding conductors,
location of antenna discharge product, connection to grounding
electrodes and requirements for grounding electrodes.
ANTENNA
LEAD IN
WIRE
GROUND
CLAMP
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
ELECTRIC
SERVICE
EQUIPMENT
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
NEC - NATIONAL ELECTRICAL CODE
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
EXAMPLE OF ANTENNA GROUNDING AS PER
NATIONAL ELECTRICAL CODE
S2898A
18. SERVICING
Do not attempt to service this product yourself as opening or removing
covers may expose you to dangerous voltage or other hazards. Refer
all servicing to qualified service personnel.
19. REPLACEMENT PARTS
When replacement parts are required, be sure the service technician
uses replacement parts specified by the manufacturer or those that
have the same characteristics as the original part. Unauthorized
substitutions may result in fire, electric shock or other hazards.
20. SAFETY CHECK
Upon completion of any service or repairs to this product, ask the
service technician to perform safety checks to determine that the
product is in proper operating condition.
21. WALL OR CEILING MOUNTING
The product should be mounted to a wall or ceiling only as
recommended by the manufacturer.
22. DAMAGE REQUIRING SERVICE
Unplug the product from the wall outlet and refer servicing to qualified
service personnel under the following conditions:
a. When the power-supply cord or plug is damaged.
b. If liquid has been spilled or objects have fallen into the product.
c. If the product has been exposed to rain or water.
d. If the product does not operate normally by following the operating
instructions. Adjust only those controls that are covered by the
operating instructions, as an adjustment of other controls may result
in damage and will often require extensive work by a qualified
technician to restore the product to its normal operation.
e. If the product has been dropped or the cabinet has been damaged.
When the product exhibits a distinct change in performance–this
f.
indicates a need for service.
23. HEAT
The product should be situated away from heat sources such as
radiators, heat registers, stoves or other products (including amplifiers)
that produce heat.
24. NOTE TO CATV SYSTEM INSTALLER
This reminder is provided to call the CATV system installer's attention
to Article 820-40 of the NEC that provides guidelines for proper
grounding and, in particular, specifies that the cable ground shall be
connected to the grounding system of the building, as close to the point
of cable entry as practical.
3
SPEAKER CONNECTION
PREPARATION FOR USE
Locate the Speaker Jacks on the rear of the unit and connect the right speaker to the Right (R) Speaker jack
and the left speaker to the Left (L) Speaker jack.
CAUTION: Only connect the speakers which are supplied with the unit. The use of any other or additional
speakers may cause damage to the unit. Never operate the unit without the speakers connected.
HEADPHONE JACK
To listen to the unit through headphones, simply insert headphones (not included) into the Headphone jack.
The speakers will be disconnected when the headphones are plugged in.
BATTERY OPERATION FOR THE REMOTE CONTROL
The battery compartment is located on the rear of the remote control.
• Remove the battery compartment door by pressing in on the tab and
lifting the battery compartment door off.
• Insert two (2) AAA size batteries into the battery compartment as shown
to the right. Be sure to observe the polarity markings which are
engraved inside the battery compartment. If the batteries are inserted
incorrectly, the remote control will not operate.
• Replace the battery compartment door.
BATTERY PRECAUTIONS
Follow these precautions when using batteries in this device:
1. Use only the size and type of batteries specified (alkaline are recommended).
2. Be sure to follow the correct polarity when installing the batteries as indicated in the battery compartment. Reversed
batteries may cause damage to the device.
3. Do not mix different types of batteries together (e.g. Alkaline, Carbon-zinc or rechargeable) or old batteries with fresh
ones.
4. If the device is not to be used for a long period of time, remove the batteries to prevent damage or injury from possible
battery leakage.
5. Do not try to recharge batteries not intended to be recharged; they can overheat and rupture.
(Follow battery manufacturer’s directions.)
AC CONNECTION
Unwind the AC cord and extend it to its full length. Insert the AC plug into any
convenient 120V 60Hz household outlet.
AC Outlet
Please note that this unit is equipped with a polarized AC plug which has one
blade wider than the other. This is a safety feature to reduce the likelihood of
electric shock. This polarized AC plug will only fit in a polarized AC outlet. If
AC Plug
you find that you cannot insert this plug into your outlet, you may have an
obsolete non-polarized outlet. Please do not try to defeat this safety feature by using a non-polarized
adapter or by filing the wider blade to make it fit into your outlet. If this plug does not fit into your outlet, you
should contact a qualified licensed electrician to replace your obsolete outlet.
IMPORTANT NOTES:
•
•
Before moving or lifting the unit, make sure the power plug is disconnected from the power source.
If there is a power failure or the AC cord is disconnected, when the power is resumed or the AC cord is
connected again. The clock will be reset ("12:00" will appear on the display) and you will need to set it
again. However, the Radio Preset stations will be kept although there is a power failure or you
disconnected the AC cord.
4
PREPARATION FOR USE (CONTINUED)
CONNECTING AN EXTERNAL UNIT
You can connect an external unit to this unit, such as a cassette player, etc. Simply connect the supplied
audio cable from the AUX IN jack on this unit to the external unit's AUX OUT jack. This will allow you to
broadcast the external unit's sound through this unit. When the unit is on, if an external unit is connected via
the AUX IN jack, the unit will change to AUX IN mode automatically; ''AUX'' will appear in the display.
To power on the unit, press the Play/Pause/Power On button or RADIO AM/FM/POWER ON button on the
remote control or on the main unit . To power off the unit, press the Power Off/Stop/Clock set button on the
remote control or on the unit.
NOTES:
• Connecting the unit to an external audio source will allow you to broadcast the external unit’s sound
through this unit’s speakers.
• When connecting the external unit, refer to the owner’s manual of the external unit, as well as this manual.
• When connecting the external unit, make sure the power is off and both units are unplugged before
making any connections.
• If using the CD or Radio function, make sure the audio cable is disconnected from the AUX IN jack.
REMOTE SENSOR
To operate the unit with the remote control, point the remote at the remote sensor on the front of the main
unit and press the appropriate button. The remote control has an effective operating range of approximately
15 feet and an angle of no more than 30°.
NOTE: Bright sunlight may interfere with the operation of the remote control.
5
FRONT
LOCATION OF CONTROLS
SLEEP Button
RADIO AM/FM/POWER ON Button
EQ/TIMER Button
ALARM/MODE/MEM+ Button
Display
TIME - /TUNING/SKIP/SEARCH o
Button
7. TIME + /TUNING/SKIP/SEARCH
N Button
8. AUX IN Jack
9. CD DOOR OPEN Button
10. PROGRAM/MEMORY Button
11. VOLUME + Button
12. VOLUME – Button
13. REPEAT/CLOCK Button
14. Remote Sensor
15. STOP (■)/TIME SET/POWER OFF
Button
16. PLAY/PAUSE (®p)/POWER ON
Button
17. Headphone Jack
1.
2.
3.
4.
5.
6.
6
REAR
LOCATION OF CONTROLS (CONTINUED)
1. Speaker Jacks
2. AC Cord
3. FM Wire Antenna
1. VOLUME + Button
2. RADIO AM/FM/POWER
ON Button
3. PLAY/PAUSE (®p)/
POWER ON Button
4. TIME - /TUNING/
SKIP/SEARCH o Button
5. VOLUME – Button
6. PROGRAM/MEMORY
Button
7. STOP (■)/TIME SET/
POWER OFF Button
8. EQ/TIMER Button
9. SLEEP Button
10.TIME +/TUNING/
SKIP/SEARCH n Button
11. ALARM/MODE/MEM+
Button
12. REPEAT/CLOCK Button
REMOTE
7
1
SETTING THE CLOCK
OPERATING INSTRUCTIONS
1
2
3
1
While the unit is off (the clock
appears in the display), press the
STOP (■)/TIME SET/ POWER
OFF button; the hour digit(s) will
blink in the display.
4
1
2
To set the hour, press the TIME-/
TUNING/SKIP/SEARCH o button
1 to decrease and/or the TIME
+/ TUNING/SKIP/SEARCH n
1
button 2 to increase the hour.
Press and hold either button for
rapid searching.
When the hour is set, press the
STOP (■ )/TIME SET/POWER
OFF button again; the minute
digits will blink in the display.
5
1
2
To set the minute, press the
TIME -/TUNING/SKIP/SEARCH
o button 1 to decrease and/or
the
TIME +/TUNING/SKIP/
SEARCH n button 2 to increase
the minute. Press and hold either
2
button for rapid searching.
PRESET EQ
1
When the minute is set, press the
STOP (■ )/TIME SET/POWER
OFF button again; the clock will
be set and the colon will blink.
SELECTING BETWEEN CD
TURNING THE UNIT ON/OFF AND RADIO MODE
1
1
2
1
2
1
3
With the power on, press the
EQ/TIMER button to cycle
through the preset EQ settings or
to turn the EQ off. Each press of
the PRESET EQ button will cycle
as follows: JAZZ, ROCK, POP,
CLASSIC, Off.
Press the PLAY/PAUSE (®p)/
POWER ON button 1 or RADIO
AM/FM/POWER ON button 2 to
turn the unit on; the display will light
brightly. Press the STOP (■)/TIME
SET/POWER OFF button 3 while
in the CD stop mode or Radio
mode to turn the unit off.
8
If the unit is in CD mode, press
the RADIO AM/FM/POWER ON
button 1 to change to Radio
mode OR If the unit is in RADIO
mode, press the PLAY/PAUSE
(®p|)/POWER ON button 2 to
change to CD mode.
OPERATING INSTRUCTIONS (CONTINUED)
LISTENING TO THE RADIO
1
2
3
Press the RADIO AM/FM/
POWER ON button to turn the
unit on; "AM" or "FM" and the
frequency will appear in the
display.
Press the RADIO AM/FM/
POWER ON button to select AM
or FM.
4
5
1
1
2
MANUAL TUNING: Repeatedly
press
the
TIME/TUNING/
SKIP/SEARCH o 1 or n 2
button to manually advance the
frequency in the display up or
down until the desired frequency
appears.
2
2
3
1
AUTOMATIC TUNING: Press
and hold the TIME/TUNING/
SKIP/SEARCH o 1 or n 2
button until the frequency in the
display starts to scan, and then
release the button; the tuner will
search and then stop on the next
strong station it finds. Repeat this
step until the desired frequency
appears in the display.
4
Press the EQ button 1 and adjust
the volume using the VOLUME +
2 or – 3 button as desired.
To turn the unit off, press the
STOP (■ )/TIME SET/POWER
OFF button 3.
Hints for Better Reception
AM–The AM ferrite bar antenna is located inside the unit. It may be necessary to turn the unit slightly so that
the internal antenna is pointing in the direction of the AM transmitter. You may have to experiment to find the
position that provides the strongest reception for each of your favorite AM stations.
FM–Make sure that the FM Wire Antenna is extended to its full length. You may have to vary the direction of
the antenna to find the strongest signal for each FM station.
9
OPERATING INSTRUCTIONS (CONTINUED)
SETTING RADIO PRESETS
This unit can preset 10 AM and 10 FM radio stations for convenient recall.
1
2
3
1
2
Press the RADIO AM/FM/
POWER ON button to turn the
unit on; "AM" or "FM" and the
frequency will appear in the
display.
Press the RADIO AM/FM/
POWER ON button to select AM
or FM.
Press the TIME/TUNING/
SKIP/SEARCH o 1 or n 2
button to select a station.
4
5
6
Press the PROGRAM/MEMORY
button again to set the station in
the selected memory.
Repeat steps 3 through 5 to
program up to 10 stations in each
band, if desired.
1
2
Press the PROGRAM/MEMORY
button 1; the preset number will
blink in the display. Press the
ALARM/MODE/MEM+ button 2
until the desired memory number
appears on the display.
RECALLING RADIO PRESETS (10 EACH BAND)
1
2
3
2
3
1
Follow steps 1 and 2 above.
Press the ALARM/MODE/MEM+
button to select a preset; the
station will automatically be tuned
in.
10
4
Press the EQ button 1 and adjust
the volume using the VOLUME +
2 or – 3 button as desired.
OPERATING INSTRUCTIONS (CONTINUED)
PLAYING COMPACT DISCS
This unit can play standard, CD-R or CD-RW CDs.
1
2
Press the PLAY/PAUSE (®p)/
POWER ON button to turn the
unit on; the display will light
brightly.
NOTE: If a CD disc is inserted,
the CD will start playing
automatically.
4
2
If the unit is in the Radio mode,
press the PLAY/PAUSE (®p|)/
POWER ON button to select CD;
1
the CD indicator will appear will
appear in the display. If a CD disc
is inserted, the CD will start
playing automatically.
5
3
If there is no disc inside the CD
compartment, press the DOOR
OPEN button on the main unit to
open the CD door and gently
press CD with label side facing
front onto the spindle until it locks
in place. Close the CD door; the
CD will automatically start playing.
3
1
4
2
Press the EQ button 1 and adjust
the volume using the VOLUME +
2 or – 3 button as desired.
Playback will continue until all the
tracks on the disc have been
played
To stop playback before the disc
ends, press the STOP (■)/TIME
SET/ POWER OFF button. Press
the STOP (■)/TIME SET/POWER
OFF button again to turn the unit
off.
1
2
During CD playback, if you wish to
pause the disc momentarily, press
the PLAY/PAUSE (®p)/POWER
ON button. Playback stops but the
disc continues to spin and the
time display will blink.
Press the PLAY/PAUSE (®p)/
POWER ON button again to
release pause and resume
normal CD playback.
CD PAUSE CONTROL
11
OPERATING INSTRUCTIONS (CONTINUED)
FORWARD/REVERSE SKIP TRACK AND HIGH-SPEED MUSIC SEARCH (
)
1
2
During playback, press the TIME +/
TUNING/SKIP/SEARCH n button
once to advance the player to the
beginning of the next track. Press
the
TIME +/TUNING/SKIP/
SEARCH n button repeatedly to
advance the player to highernumbered tracks.
During playback, press the TIME -/
TUNING/SKIP/SEARCH o button
once to move the player back to the
beginning of the current track. Press
the
TIME -/TUNING/SKIP/
SEARCH o button repeatedly to
move the player back to lowernumbered tracks.
During playback, depress and
hold either the TIME/TUNING/
SKIP/SEARCH n or o button to
move the player forward or
backward within a track to locate
a specific musical passage. The
player will move forward or
backward at high speed as long
as the button is depressed. When
you release the TIME/TUNING/
SKIP/SEARCH n or o button,
1
normal playback will resume.
1
2
3
To play the tracks on the CD in a
random order, press the ALARM/
MODE/MEM+ button while in the
Stop mode; “RANDOM” will
appear in the display
Press the PLAY/PAUSE (®p)/
POWER ON button and the
tracks will play in a random order.
To stop and cancel Random
playback, press the STOP (■)/
TIME SET/POWER OFF button
once, the unit will stop the
1
random playback
and "RANDOM"
will disappear from the display.
1
2
3
To hear the first 10 seconds of
each track, press the ALARM/
MODE/MEM+ button twice while
in the Stop mode; “INTRO” will
appear in the display.
Press the PLAY/PAUSE (®p)/
POWER ON button and the first
10 seconds of each track will
play.
To stop and cancel INTRO
playback, press the STOP (■)/
TIME SET/POWER OFF button
once, the unit will stop the intro
playback and "INTRO" will
disappear from the display.
RANDOM PLAYBACK
INTRO PLAYBACK
3
/
12
OPERATING INSTRUCTIONS (CONTINUED)
REPEAT PLAYBACK ONE TRACK OR ALL TRACKS
1
3
2
3
To repeat all of the tracks on a
disc continuously, press the
REPEAT/CLOCK button twice
while in the Play mode; “REPEAT
ALL” will light in the display. All
tracks on the disc will be repeated
continuously.
To cancel Repeat Playback,
press the REPEAT/CLOCK
button until “REPEAT 1” and
“REPEAT ALL” indicators
disappear from the display.
2
1
To repeat a single track, press the
REPEAT/CLOCK button ❶ once
while in the Play mode; “REPEAT
1” will appear in the display.
Press the TIME/ TUNING/SKIP/
SEARCH n 2 or o 3 button to
select the specific track that you
wish to repeat. The specific track
you selected will be repeated
continuously.
PROGRAMMED PLAYBACK
2
The CD player in this unit has a 20 track programmable memory that allows you to program up to 20 tracks
on any disc for playback in any desired order. You may program 20 different tracks or you may also program
certain tracks to play more than once.
To perform Programmed playback, proceed as follows:
1
2
3
1
2
1
With the unit on and a CD
inserted, press the PLAY/PAUSE
(®p)/POWER
ON
button
repeatedly to select CD (if in a
mode other than CD); the CD
indicator will appear in the display
and will automatically start
playing.
Press the STOP (■)/TIME SET/
POWER OFF button 1 to stop
automatic playback. Press the
PROGRAM/MEMORY button 2;
“P01”
(program
number),
“PROGRAM” and “00” (track
number) will appear in the
display.
13
2
3
Press the TIME/ TUNING/SKIP/
SEARCH o 1 or n 2 button to
select the first track that you wish to
program. When the desired track
number appears in the display,
press the PROGRAM/MEMORY
button 3 again.
OPERATING INSTRUCTIONS (CONTINUED)
4
5
1
1
2
3
2
3
Press either the TIME/ TUNING/
SKIP/SEARCH o 1 or n 2 button
to select the next track you wish to
program. When the desired track
number appears in the display,
press the PROGRAM/MEMORY
button 3 again.
6
1
2
PROGRAMMED REPEAT
1
Repeat step 5 until you have
programmed up to 20 track
numbers into the CD Program
Memory. When the memory is
full, it will stay on program 20.
After programming up to 20 tracks in the CD Program Memory, press
the PLAY/PAUSE (®p)/POWER ON button 1 to begin Programmed
playback. “PROGRAM” will appear in the display and playback will
begin on the first track that you programmed. The player will continue
to play all of the tracks that you programmed in the order in which you
programmed them. When the last programmed track has been played,
the player will stop. To play back the program again, press the
PLAY/PAUSE (®p)/ POWER ON button 1.
To clear the CD Program Memory, while in the Stop mode, press the
STOP (■)/TIME SET/POWER OFF button 2 to clear the programmed
memory. Press the STOP (■)/TIME SET/POWER OFF button 2 a
third time to turn the unit off.
1
2
3
1
2
It is also possible to use the
Program and Repeat functions
together to repeat a specific
program indefinitely. First, program
the tracks in the order you wish to
hear them as described above.
The "PROGRAM" indicator will
appear in the display.
Press the PLAY/PAUSE (®p)/
POWER ON button 1 to begin
the Programmed playback; then
press the REPEAT/CLOCK
button 2 twice to enter the repeat
All mode; "REPEAT ALL" will
appear in the display. The player
will play the tracks you selected in
the order in which you
programmed them. When the last
track in the program has been
played, the entire program will
begin again.
14
Programmed Repeat playback
will continue indefinitely until you
press the STOP (■)/TIME SET/
POWER OFF button.
OPERATING INSTRUCTIONS (CONTINUED)
SETTING THE TIMER
Set the timer to turn the unit on and off to the Tuner or CD mode at a preset time as follows:
1
2
3
1
2
1
With the power off, press the
REPEAT/CLOCK button 1 and
then press the STOP (■)/TIME
SET/ POWER OFF button 2
within 5 seconds to enter the
Timer ON setting mode; “TIMER”
will appear and the hour will blink
on the display.
4
1
4
2
3
4
Press the ALARM/MODE/MEM+
button to select the desired wake
up function (CD or RADIO). Make
sure to insert a CD or tune a
station as desired before turning
the unit off.
2
3
Press
the
TUNING/SKIP/
SEARCH/TIME o 1 or n 2 button
to set the timer On hour and then
press the STOP (■)/TIME SET/
POWER OFF button 3 again; the
minutes will blink.
Press the TIME/TUNING/SKIP/SEARCH o 1 or n 2 button to set the
timer On minute and then press the STOP (■)/TIME SET/POWER
OFF button 3 again; the timer will then be set. When the actual time
matches the Timer’s On time, the unit will turn on to the function
selected in Step 2. To turn off the timer, press the EQ/TIMER button 4;
the unit will turn off.
TO ACTIVATE THE TIMER ON MODE, with the unit off, press the EQ/TIMER button; “TIMER” will appear in
the display next to the current time. To cancel, press the EQ/TIMER button again; “TIMER” will disappear in
the display.
NOTES:
• Before activating the timer, make sure the unit is in the Standby mode. Otherwise, there will not be sound
when the Timer’s On time is reached.
• Before activating the timer, make sure there is a disc inside the CD compartment when waking to a CD,
or make sure a AM/FM station is tuned before turning off the unit. Otherwise, there will not be sound
when the Timer’s On time is reached.
• When TIMER On time is reached, the unit will turn on for CD or Radio for 1 hour then turn off. If the CD
disc total tracks is below 1 hour, then the unit will playback all the tracks on the CD and then stop.
15
2
2
OPERATING
INSTRUCTIONS
(CONTINUED)
ACTIVATING THE SLEEP FUNCTION
3
Set the sleep timer as follows:
3
1
2
With the unit is on, press the
SLEEP button and “OFF” and
“SLEEP” will appear in the
display. Press the SLEEP button
again; “90” will appear in the
display and the unit will turn off
after 90 minutes.
Press the SLEEP button a second
time to set the unit to turn off after
60 minutes. Each additional press
with decrease the sleep time (90,
60, 45, 30, 15, OFF). Press the
SLEEP button repeatedly until
“OFF” appears in the display to
deactivate the Sleep feature.
16
CARE AND MAINTENANCE
Caring for Compact Discs
• Treat the compact disc carefully. Handle the compact disc
only by its edges. Never allow your fingers to come in
contact with the shiny, unprinted side of the compact disc.
• Do not attach adhesive tape, stickers, etc. to the compact
disc label.
• Clean the compact disc periodically with a soft, lint-free,
dry cloth. Never use detergents or abrasive cleaners to
clean the compact disc. If necessary, use a CD cleaning kit.
• If a compact disc skips or gets stuck on a section of the compact disc, it is probably dirty or damaged
(scratched).
• When cleaning the compact disc, wipe in straight lines from the center of the compact disc to the outer
edge of the compact disc. Never wipe in circular motions.
B E NZEN E
C LE A N E R
• This unit is designed to play only compact discs bearing the identification logo as shown here.
Other compact discs may not conform to the CD standard and may not play properly.
• Compact discs should be stored in their cases after each use to avoid damage.
• Do not expose compact discs to direct sunlight, high humidity, high temperatures or dust, etc. Prolonged
exposure or extreme temperatures can warp the compact disc.
• Do not stick or write anything on either side of the compact disc. Sharp writing instruments, or the ink,
may damage the surface.
Cleaning the Unit
• To prevent fire or shock hazard, disconnect your unit from the AC power source when cleaning.
• The finish on your unit may be cleaned with a dust cloth and cared for as other furniture. Use caution
when cleaning and wiping the plastic parts.
• Mild soap and a damp cloth may be used on the front panel.
17
TROUBLESHOOTING GUIDE
Should this unit exhibit a problem, check the following before seeking service:
Symptom
Possible Cause
Solution
Noise or sound distorted
on radio broadcasts.
Station not tuned properly for
AM or FM.
AM: Unit is not positioned correctly.
FM: Wire antenna is not extended.
Retune the AM or FM broadcast
station.
Rotate unit for best reception.
Extend wire antenna.
Radio
AM or FM, no sound.
Compact Disc Player
CD Player will not play.
CD skips while playing.
General
No power.
Remote not working.
Tuner is not selected.
Volume at minimum.
Press the RADIO AM/FM button to
select Tuner; AM or FM will appear.
Increase volume.
CD is not selected.
CD is not installed or is installed
incorrectly.
Press the PLAY/PAUSE (®p)/
POWER ON button to select CD;
the CD indicator will appear in
the display.
Insert CD with label facing forward.
Disc is dirty or scratched.
Wipe disc with cloth or use
another disc.
AC power cord is not connected.
Connect AC power cord.
Batteries not inserted, or inserted
incorrectly.
Insert batteries correctly.
FOR ADDITIONAL SET-UP OR OPERATING ASSISTANCE, PLEASE VISIT OUR WEBSITE AT
WWW.MEMOREXELECTRONICS.COM
OR CONTACT CUSTOMER SERVICE AT (954) 660-7100.
PLEASE KEEP ALL PACKAGING MATERIAL FOR AT LEAST 90 DAYS IN CASE YOU NEED
TO RETURN THIS PRODUCT TO YOUR PLACE OF PURCHASE OR MEMOREX.
FOR PARTS AND ACCESSORIES, CONTACT FOX INTERNATIONAL AT 1-800-321-6993.
18
SPECIFICATIONS
GENERAL
Power Source (Main Unit) ..........................................................................AC 120V, 60 Hz
Power Source (Remote Control) ..........................................DC 3V, 2 x “AAA” size battery
Speaker .............................................................................................................4 Ohms x 2
Output Power.......................................................................................................12.5W x 2
RADIO SECTION
Frequency Range (FM). ...............................................................................87.5–108 MHz
Frequency Range (AM)................................................................................520–1710 KHz
CD SECTION
Disc Diameter...............................................................................................4.72" (120mm)
Optical Source ...................................................................................Semiconductor Laser
Specifications are subject to change without notice.
19
Memcorp, Inc.
Weston, FL
Printed in Hong Kong
Visit our website at www.memorexelectronics.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement