Minolta 2210 Printer User Manual

Minolta 2210 Printer User Manual
magicolor 2210
User’s Guide
®
1800669-001B
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
Trademarks
The following are registered trademarks of MINOLTA-QMS, Inc.: QMS, the MINOLTAQMS logo, Crown, CrownNet, and magicolor.
Minolta is a trademark of Minolta Co., Ltd. Other product names mentioned in this
guide may also be trademarks or registered trademarks of their respective owners.
Proprietary Statement
The digitally encoded software included with your printer is Copyrighted © 2001 by
MINOLTA-QMS, Inc. All Rights Reserved. This software may not be reproduced, modified, displayed, transferred, or copied in any form or in any manner or on any media,
in whole or in part, without the express written permission of MINOLTA-QMS, Inc.
Copyright Notice
This guide is Copyrighted © 2001 by MINOLTA-QMS, Inc., One Magnum Pass,
Mobile, AL 36618. All Rights Reserved. This document may not be copied, in whole or
part, nor transferred to any other media or language, without written permission of
MINOLTA-QMS, Inc.
Notice
MINOLTA-QMS, Inc. reserves the right to make changes to this guide and to the
equipment described herein without notice. Considerable effort has been made to
ensure that this guide is free of inaccuracies and omissions. However, MINOLTAQMS, Inc. makes no warranty of any kind including, but not limited to, any implied
warranties of merchantability and fitness for a particular purpose with regard to this
guide. MINOLTA-QMS, Inc. assumes no responsibility for, or liability for, errors
contained in this guide or for incidental, special, or consequential damages arising
out of the furnishing of this guide, or the use of this guide in operating the equipment,
or in connection with the performance of the equipment when so operated.
Registering the Printer
Mail—Fill out and send in the
registration card enclosed in
your shipment or downloaded
from www.onlineregister.com/
minolta-qms/
Internet—Follow the
instructions on
www.onlineregister.com/minoltaqms/
or
Software Utilities CD-ROM—
Follow the instructions on the
CD-ROM.
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
Contents
4
5HSODFLQJ &RQVXPDEOHV 1111111111111111111111111111111111111111111111111111111111111111111111111111111111 8
&RQVXPDEOH /LIH ([SHFWDQFLHV 9
5HSODFLQJ &RQVXPDEOHV 9
2UGHULQJ &RQVXPDEOHV ;
5HSODFLQJ 7RQHU &DUWULGJHV ;
7RQHU &DUWULGJH /LIH ;
7RQHU &DUWULGJH +DQGOLQJ <
7RQHU &DUWULGJH 5HSODFHPHQW 43
5HILOOHG 7RQHU &DUWULGJHV 45
5HSODFLQJ WKH 23& 'UXP .LW 46
:DVWH 7RQHU 3DFN/ 23& 'UXP &DUWULGJH/ DQG /DVHU /HQV &RYHU 46
5HPRYLQJ WKH 8VHG :DVWH 7RQHU 3DFN 46
5HPRYLQJ WKH 8VHG 23& 'UXP &DUWULGJH 48
5HSODFLQJ WKH /DVHU /HQV &RYHU 49
,QVWDOOLQJ WKH 1HZ 23& 'UXP &DUWULGJH 4:
,QVWDOOLQJ WKH 1HZ :DVWH 7RQHU 3DFN 4<
5HSODFLQJ WKH )XVHU 8QLW DQG 7UDQVIHU 5ROOHU .LW 4<
5HSODFLQJ WKH )XVHU 8QLW 53
5HSODFLQJ WKH 7UDQVIHU 5ROOHU 8QLW 57
5HSODFLQJ WKH )XVHU 2LO 5ROOHU 59
5HSODFLQJ WKH 7UDQVIHU %HOW 5;
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
2
Using Media .....................................................................................................33
Introduction 34
Media Handling 34
Media Types 35
Plain Paper 35
Letterhead and Memo Media 35
Thick Stock 36
Envelopes 37
Labels 37
Postcards 38
Transparencies 38
Loading Media 40
Autoduplexing 40
Upper and Optional Media Trays 41
Multipurpose Tray 43
Printing Envelopes from the Multipurpose Tray 45
Printing Area 46
Media Storage 46
3
Maintaining the Printer ....................................................................................47
Maintaining the Printer 48
Cleaning 50
Outside the Printer 50
Inside the Printer 50
4
Troubleshooting ..............................................................................................51
Introduction 52
Printing a Status Page 52
Preventing Media Jams 52
Automatic Jam Recovery 53
Understanding the Media Path 54
Media Tray (Standard Upper Tray and Optional Tray) 55
Lower Feed Unit (LFU) Tray(s) 55
Multipurpose Tray 55
Duplex Unit (Optional) 55
5-bin Mailbox (Optional) 55
Clearing Media Jams 55
Handling Media Jams by Location 56
Clearing Misfeed (Upper or Optional Tray) Jams 57
Clearing Misfeed (Multipurpose Tray) Jams 58
Clearing Inner Jams, Outer Jams, and Drum Jams 58
Media Jams in the Output Tray 66
Solving Problems with Media Jams 66
Make sure that you are using only plain paper (or recycled plain paper). 66
Make sure that you are using only letter/A4 plain paper. 66
Solving Other Problems 69
2
Contents
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
Solving Problems with Printing Quality 74
Status, Error, and Service Messages 85
Status and Error Messages 85
Service Messages 94
HP-GL, HPXL, and PCL Error Codes 97
PostScript Errors 98
Additional Assistance 98
5
Installing Other Accessories .......................................................................... 99
Introduction 100
Accessories 101
Antistatic Protection 101
BuzzBox 101
What's in the Kit? 102
Installing BuzzBox 102
Using BuzzBox 103
Dual In-Line Memory Modules 103
How Much Memory Do You Need? 104
Minimum System Memory Requirements (in MB) 104
Installing a Duplex Unit 107
Emulations, Fonts, and Other Software 112
Emulations 112
Fonts 114
Kanji Font Internal IDE Hard Disk 115
5-bin Mailbox 117
QFORM 122
PlanetPress 122
Interfaces and Daughterboards 123
Interfaces 123
SCSI Interface 125
Internal IDE Hard Disk Drive 127
Lower Feeder Unit 130
Installing a Lower Feeder Unit (LFU) 130
Media Trays 134
Installation 134
Printer Stand/Cabinet 135
SC-210 Convenience Copier 135
Time-of-Day Clock 135
6
Color Printing ................................................................................................ 139
Introduction 140
Color Management and Control 140
MINOLTA-QMS QCOLOR Technology 140
Further Information 141
Contents
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
3
7
Repacking the Printer ...................................................................................143
Storing the Printer 144
Relocating Your Printer 144
Repacking the Printer 145
What's Involved? 145
Remove the Cables 146
Remove the Fuser Oil Roller 146
Remove the Toner Cartridges 146
Remove the Waste Toner Pack 147
Remove OPC Drum Cartridge 147
Remove Transfer Belt 147
Remove the Duplex Unit 147
Remove the 5-bin Mailbox 148
Remove the Lower Feeder Unit 148
Repack the Printer 149
Strapping/Buckling Kit Contents 150
A Technical Specifications .................................................................................153
Requirements 154
Space Requirements 154
Power Requirements 155
Location Requirements 155
Engine and Controller Specifications 157
Engine 157
Print Speed—Simplex 157
Print Speed—Autoduplex 158
General 158
Controller
159
Electrical 160
Physical 162
Print Media 162
Document Option Commands 163
Supported DOCs 163
Header/Trailer Page Commands 163
HP-GL Emulation Commands 163
HP PCL 5e Emulation Commands 164
Lineprinter Emulation Commands 164
CCITT Groups 3 and 4 Commands 164
Document Formatting 165
Job and Subjob Boundary Commands 165
LN03 Plus Commands 166
Index......................................................................................................................167
4
Contents
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
Replacing
Consumables
1
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
Consumable Life Expectancies
The stated life expectancy of each consumable is based on printing under
specific operating conditions, such as media type, number of color planes,
page size, and page coverage (@ normal 5% coverage of letter/A4-size
media). The actual life expectancy will vary depending on these and other
printing variables, including continuous or intermittent printing, ambient temperature, and humidity. For further information about the consumables statistics page and replacement menus, refer to the CrownBook.
Replacing Consumables
Attention
Failure to follow instructions as outlined in this manual could result in
voiding your warranty.
The following messages indicate that a consumable needs to be replaced.
6
Item/Message
Display
This item needs replacing by user
after...
Page Reference
Fuser oil roller
REPLACE
OIL
ROLLER
FUSER OIL LOW, FUSER OIL
“Replacing the
EMPTY, or REPLACE OIL ROLLER Fuser Oil Roller”
displays in the message window (after on page 26
up to 21,000 single- sided continuous
monochrome or 7,500 continuous
color pages*, or 7,000 intermittent
monochrome or 5,000 intermittent
color pages). Heavy coverage, intermittent printing, and different media
types can use up oil at an accelerated
rate, reducing fuser oil roller life.
Fuser unit/transfer roller kit
REPLACE
FUSER
UNIT
100,000 single-sided pages maximum
at an equal mix of black and 4-color
pages, all with 5% coverage of each
color; however, fuser unit life is coverage and media dependent).
“Replacing the
Fuser Unit and
Transfer Roller
Kit” on page 19
Consumable Life Expectancies
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
Item/Message
Display
This item needs replacing by user
after...
OPC drum kit**
REPLACE
OPC DRUM
REPLACE
WASTE
TONER
WASTE
TONER
NEAR
FULL
Up to 30,000 continuous monochrome “Replacing the
or 7,500 continuous four-color pages, OPC Drum Kit”
or 10,000 intermittent [one-page jobs] on page 13
monochrome or 5,000 intermittent
[one-page jobs] color pages). Other
factors also affect consumables life.
Toner
<COLOR>
TONER
EMPTY
Approximately 6,000 single-sided
pages per cartridge—black, yellow,
magenta, cyan at 5% coverage of
each color.
Transfer belt
107,000 single-sided images (1:1
REPLACE
color/monochrome printing)
TRANSFER
BELT
Page Reference
“Replacing Toner
Cartridges” on
page 8
“Replacing the
Transfer Belt” on
page 28
*A plane (also called an image) is a single pass of the OPC drum (one
toner color). For example, a black-only, single-sided (simplex) print job
makes one pass per page. A single-sided color page (also called a face)
consists of up to four passes of the OPC drum, since most color print jobs
use all four toner colors. A two-sided color page may consist of up to eight
passes of the OPC drum, since most color print jobs use all four toner colors. Stated consumable life is expressed at 5% in simplex letter/A4 pages.
A duplex page is equivalent to two simplex pages.
The number of sheets/faces printed shown on the startup page differs from
the number of sheets/faces printed statistics in CrownView and on the consumables statistics page (Operator Control/Consumables/Print Statistics).
The numbers on the startup page refer to number of sheets/faces printed
during the lifetime of the printer. The numbers in CrownView and on the
consumables statistics page refer to the number of sheets/faces printed to
date during the current consumables tracking period (Administration/Consumables/Start Period menu).
**Three items (OPC drum, laser lens cover, waste toner pack) are included
in the OPC drum kit. If one needs replacing, replace all three items.
Replacing Consumables
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
7
Ordering Consumables
Choosing the right consumables for your magicolor 2210 printer not only
increases its reliability and performance, but also minimizes the risk of
damage. For example, only MINOLTA-QMS toner cartridges are designed to
meet the exact specifications of your MINOLTA-QMS printer, giving maximum
performance, efficiency, and long life.
Toner cartridges and other consumables for the magicolor 2210 are available
from your local vendor or Q-SHOP (www.q-shop.com). See the Service &
Support Guide for the telephone number of the MINOLTA-QMS office nearest
you for information on ordering.
Replacing Toner Cartridges
Characters and images are created in your laser printer through a process
that applies toner to the photosensitive (OPC) drum (which functions like photographic film). Your printer uses four toner cartridges: black, yellow,
magenta, and cyan. Handle the toner cartridges carefully to avoid spilling
toner inside the printer or on yourself.
5"
The carbon-particle toner is nontoxic. If you get toner on your hands,
wash them in cool water or a neutral detergent. If you get toner on
your clothes, lightly dust them off as much as possible. If some toner
remains on your clothes, use cool, not hot water, to rinse the toner off,
provided your clothing is washable.
WARNING!
If you get toner in your eyes, wash it out immediately and consult a
doctor. Material Safety Data Sheets (MSDS) information can be found at
www.minolta-qms.com (click on the Answer Base).
ACHTUNG! Sollte Toner in Ihre Augen gelangen, die Augen unbedingt
sofort mit kaltem Wasser ausspülen und einen Artzt aufsuchen.
MSDS-Informationen (Material Safety Data Sheets; Datenblätter zur
Materialsicherheit) finden Sie im Internet unter www.minolta-qms.com
(klicken Sie auf “Answer Base”).
Toner Cartridge Life
A toner cartridge contains enough toner (yellow, magenta, cyan, or black) to
print a maximum of 6,000 (at normal 5% page coverage) simplex letter/
A4-size pages. With heavier coverages, the approximate maximum
8
Replacing Toner Cartridges
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
capacities will decrease. The approximate maximum simplex letter/A4 pages
for heavier coverages are below:
Pages
5"
5%
10%
15%
20%
25%
30%
35%
40%
6,000
3,000
2,000
1,500
1,200
1,000
857
750
To determine your average percent coverage, print a consumables
statistics page (Operator Control/Consumables/Print Statistics).
When toner runs low in a cartridge, X TONER LOW displays in the message
window (X indicates the toner color). It’s your option whether to continue
printing; usually, parts of the page print lighter.
When toner is low, it’s sometimes helpful to take the cartridge out of the
printer and redistribute the toner by gently rocking the cartridge horizontally
side to side (as you do for a new cartridge) five or six times. Then reinstall the
cartridge.
The printer, approximately 100 pages after detecting that toner in a cartridge
is low, displays X TONER EMPTY in the message window (X indicates the
toner color). Printing continues even though the out-of-toner warning
appears. However, the color gradually fades, so replace the toner cartridge
as soon as possible.
Toner Cartridge Handling
Attention
Do not hold a toner cartridge vertically. Do not
touch the toner roller surface c or the
protective shutter d. This could lower image
quality.
c#d
Keep toner cartridges:
„ In their packaging until you’re ready to install them.
„ In a cool, dry location away from sunlight (due to heat).
The maximum storage temperature is 95 ° F (35 ° C) and the maximum
storage humidity is 80% without condensation.
„ Level during storage.
Do not stand or store cartridges on their ends or turn them upside
down; the toner inside the cartridges may become caked or unequally
distributed.
„ Away from salty air and corrosive gases such as aerosols.
„ Away from disk drives and floppy disks.
The magnets in the cartridges can damage stored data.
Replacing Toner Cartridges
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
9
Toner Cartridge Replacement
1
2
Check the message display to see what toner color is out.
Open the printer’s front cover.
Attention
Be careful not to spill toner on the inside of the printer’s front cover.
Toner will fall from there into the upper media tray. If toner does fall
onto the open cover, immediately wipe it with a dry, lint-free soft
cotton cloth or swabs.
If the toner cartridge you want to replace is the one showing, go to step 5.
If not, go to step 3.
3
Press the toner cartridge
carrousel button c and
release the button d before
turning the carrousel dial
e counterclockwise until it
stops.
The carrousel rotates 90°
and stops.
The toner cartridge carrousel may start to turn auto1
matically from the weight of
the inserted toner cartridge.
Make sure you have fully
turned to the next slot before
trying to insert another toner cartridge.
4
5
10
2
3
Repeat step 3 until the color to be replaced is visible.
Pull the release lever to eject and
remove the toner cartridge you
are going to replace.
Replacing Toner Cartridges
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
WARNING!
Dispose of the used toner cartridge according to your local
regulations. Do not dispose of it by burning.
ACHTUNG! Entsorgen Sie alte Tonerkassetten keinesfalls durch
Verbrennen, sondern ordnungsgemäß entsprechend den lokalen
Bestimmungen.
6
7
Remove the new toner cartridge
from its shipping carton.
Distribute the toner inside the
cartridge.
Holding a cartridge with both
hands, gently shake it five or
six times.
Replacing Toner Cartridges
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
11
8
There are two types of toner cartridge available. Look at the following
graphics to determine which type you have.
„ If you have this type of toner cartridge, „ If you have this type of toner cartridge,
remove the protective yellow cover
go to step 9.
clearly marked “Remove.” Then go to
step 9.
5"
9
10
11
Each toner cartridge has a colored end that corresponds to a colored label inside the cartridge slots. Always install the toner cartridge in the slot with a label of the same color.
Place the front end of the toner
cartridge installation guides
into the cartridge installation
rails on the cartridge carrousel.
Gently push the new cartridge
into the printer.
Close the printer’s front cover.
Refilled Toner Cartridges
Attention
Refilled toner cartridges may produce variations in toner quality and
reliability and can reduce the print quality of your documents. Any
damage to the printer or quality problems caused by a refilled toner
cartridge use will void your warranty.
12
Replacing Toner Cartridges
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
Replacing the OPC Drum Kit
Waste Toner Pack, OPC Drum Cartridge, and Laser Lens
Cover
Attention
The OPC drum is extremely sensitive to bright light and direct sunlight.
Always leave it in its protective bag until you’re ready to install it. Any
exposure to light should be avoided, or permanent damage could
result. Any damage resulting from mishandling of the OPC drum will
void the warranty of the OPC drum. Also, handle the cartridge carefully
by its sides so you don’t touch the surface (the green part) of the drum.
The drum is also extremely sensitive to hand oils and scratches, both of
which reduce print quality.
The three items below are included in the OPC drum kit. If one needs
replacing, replace all three items.
„ Waste toner pack
„ OPC drum cartridge
„ Laser lens cover
The steps are
„ Removing the used waste toner pack
„ Removing the used OPC drum cartridge
„ Replacing the laser lens cover
„ Installing the new OPC drum cartridge
„ Installing the new waste toner pack
Removing the Used Waste Toner Pack
When you replace the OPC drum cartridge, the printer automatically recovers. However, the replaced waste toner pack consumables monitoring system
must be manually reset through control panel (Operator Control/
Consumables/Items Replaced) menu.
1
Open the printer’s front cover.
Replacing the OPC Drum Kit
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
13
2
Carefully remove the waste
toner pack using the handle.
Keep the waste toner pack
upright so the toner does
not spill.
3
4
Turn the two caps labeled “A”
counterclockwise and remove them.
Twist the two “A” caps c onto the
two “A” holes d.
Turn the caps clockwise to secure
them.
1
22
11
22
14
Replacing the OPC Drum Kit
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
5
6
Remove waste toner pack cap labeled
“B” and insert it into
hole “B.”
Dispose of the used waste toner pack.
WARNING!
Dispose of the used waste toner pack properly according to your local
regulations (do not dispose of it by burning).
Achtung! Entsorgen Sie den Alttonerbehälter keinesfalls, indem Sie ihn
verbrennen, sondern ordnungsgemäß entsprechend den lokalen
Bestimmungen.
7
Continue with replacing the OPC drum cartridge.
You will install the new waste toner pack after replacing the OPC drum.
Removing the Used OPC Drum Cartridge
When the OPC drum is worn out, the message REPLACE DRUM appears. The
printer will not print until the drum kit is replaced.
When you replace the OPC drum cartridge after a DRUM LOW or REPLACE
DRUM message displays in the message window, the printer automatically
recovers.
5"
1
The OPC drum life is directly related to the number of rotations of the
drum. Longest drum life is achieved with continuous printing. Intermittent printing with small job sizes requires cleaning rotations before and
after each job, and subsequently will impact OPC life.
With the front cover open, rotate
the transfer belt unit left release
lever counterclockwise to the
top (12 o’clock) position.
This raises the transfer
belt unit.
Replacing the OPC Drum Kit
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
15
2
3
Hold the OPC drum cartridge
handle and carefully pull it out
about 8 inches
(20 cm).
Support the bottom of the
drum with your hand, then
carefully pull the cartridge
toward you and remove it.
5"
4
Dispose of it properly according to your
local regulations.
Continue with replacing the
laser lens cover.
Replacing the Laser Lens Cover
1
Press on the laser lens cover lock
release lever and gently pull the
laser lens cover toward you.
5"
2
Dispose of it properly according to your local regulations.
Remove the new laser lens cover
from the OPC drum kit box.
Attention
Do not touch the glass surface of the laser lens.
16
Replacing the OPC Drum Kit
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
3
4
Place the front end of the
laser lens cover into its installation rail.
Carefully insert the laser lens
cover and check to make sure
it is fully inserted.
Attention
If the laser lens cover is not properly installed, serious damage to
the printer could result.
5
Continue with replacing the OPC drum cartridge.
Installing the New OPC Drum Cartridge
1
Remove the new OPC drum
cartridge from its shipping box.
Attention
Keep the protective sheet on the cartridge. Do not touch the
protective sheet on the photosensitive (green) surface or scratch the
surface. This could lower image quality.
Make sure the transfer belt left release lever is still set to its top position
(12 o’clock).
Replacing the OPC Drum Kit
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
17
2
3
Hold the OPC drum cartridge level, place the front
end of the OPC drum cartridge installation guide
into the installation rail.
Carefully push the OPC
drum cartridge in.
Attention
The cartridge should slide easily into the printer. Don’t force it.
4
5
Press on the front handle of the
OPC drum cartridge with one hand
and hold the front handle of the
OPC protective cover with the
other hand.
Peel the protective cover off
(straight toward you).
5"
6
Dispose of it properly
according to your local
regulations.
Turn the left release lever of the
transfer belt clockwise to its correct position (2 o’clock).
This lowers the transfer belt.
Also make sure the transfer belt
right release lever is set to its
correct position (10 o’clock).
Attention
If the transfer belt left release lever is at its top position (12 o’clock),
the waste toner pack cannot be installed.
18
Replacing the OPC Drum Kit
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
Installing the New Waste Toner Pack
1
2
3
4
Remove the new waste toner pack from the drum kit box.
Insert the bottom of the waste
toner pack c into its installation position in the printer.
2
Insert the top of the waste
toner pack d into its installation position in the printer until
it is firmly seated.
Close the printer’s front cover.
1
If the waste toner pack is not
correctly installed or the transfer belt right release lever is at
its top position (12 o’clock),
the front cover cannot be
closed.
5
In the Operator Control/Consumables/Items Replaced/Waste Toner
menu, choose Yes to reset the consumables monitoring system.
Replacing the Fuser Unit and Transfer
Roller Kit
WARNING!
The fuser unit can become extremely hot and cause severe
burns. Make sure the unit is cool before handling it.
ACHTUNG! Die Fixiereinheit kann sehr heiß werden, so daß
Verbrennungsgefahr besteht. Bitte lassen Sie die Fixiereinheit einige
Zeit abühlen, bevor Sie diese berühren.
When the fuser is worn out, the message “REPLACE FUSER UNIT” appears
and the printer does not print. Replace the fuser kit. After the new fuser kit is
installed, printing automatically resumes.
The fuser kit includes the two items below. When replacing the fuser unit,
replace the transfer roller as well.
Replacing the Fuser Unit and Transfer Roller Kit
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
19
„ Fuser unit
„ Transfer roller
unit
Replacing the Fuser Unit
1
2
3
Open the printer’s top cover.
Rotate the two fuser oil roller
lock levers to release the fuser
oil roller.
Remove the fuser oil
roller.
Hold it by the green
handle only.
20
Replacing the Fuser Unit and Transfer Roller Kit
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
4
Place the fuser oil roller on a table or level surface.
Attention
Since the fuser oil roller removed here is
to be installed in the new fuser unit,
handle it with care.
If you set the fuser oil roller on the table
do it as shown in the illustration. Do not
allow the roller surface to contact the
table or get dirty. This could lower image quality.
5
Turn the release levers
(front, rear) to release
the fuser unit.
Replacing the Fuser Unit and Transfer Roller Kit
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
21
6
Holding the fuser
unit handles, lift up
the unit.
5"
7
22
Dispose of it
properly
according to
your local
regulations.
Remove the new fuser from
its shipping box.
Replacing the Fuser Unit and Transfer Roller Kit
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
8
9
Carefully lower the new fuser unit so that the two pins in the fuser unit
installation section go into the two installation holes in the fuser unit.
Press in on the fuser unit
release levers c and rotate
them downward d.
11
This secures the fuser unit.
22
11
22
Attention
If the fuser unit release levers are not set correctly, the fuser oil
roller cannot be installed. Set the fuser unit release levers to the
fixed position.
Replacing the Fuser Unit and Transfer Roller Kit
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
23
10
11
12
Reinstall the fuser oil roller
(removed in step 4).
Rotate the two oil roller
levers to lock the oil roller into place.
Close the printer’s top cover.
Check the release button to make
sure the top cover is properly closed.
Replacing the Transfer Roller Unit
5"
1
24
If there is media in the multipurpose tray, remove it. Close the multipurpose tray.
Press the right cover release
button and carefully open the right
cover.
Replacing the Fuser Unit and Transfer Roller Kit
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
2
Holding the two transfer roller
unit handles, remove the transfer roller unit.
5"
3
Dispose of it properly
according to your local
regulations.
Remove the new transfer roller
unit from the fuser kit box.
Attention
Do not touch the surface of the transfer roller
unit. This could lower image quality.
4
5
6
Place the new transfer roller unit on a
level surface.
Lift up the two transfer roller unit handles.
Holding the two transfer roller unit
handles, carefully lower it so the
transfer roller unit shaft goes into
the two transfer roller unit installation guides.
Replacing the Fuser Unit and Transfer Roller Kit
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
25
7
8
Lower the two transfer roller
unit handles.
Carefully close the right
cover.
Check the release button
status to make sure the cover
is properly closed.
9
If necessary, reopen the
multipurpose tray and put the
media back in.
Replacing the Fuser Oil Roller
The fuser oil roller provides a lubricant for the printer via an oil-impregnated
roller. This oil is necessary for the proper functioning of the printer.
WARNING!
The fuser unit can become extremely hot and cause severe
burns. Make sure the unit is cool before handling it.
ACHTUNG! Die Fixiereinheit kann sehr heiß werden, so daß
Verbrennungsgefahr besteht. Bitte lassen Sie die Fixiereinheit einige
Zeit abühlen, bevor Sie diese berühren.
When the fuser oil roller is worn out, the message “REPLACE OIL ROLLER”
appears and the printer does not print. Replace the fuser oil roller. After the
new roller is installed, printing automatically resumes (if you have not turned
off the printer).
1
2
Open the printer’s top cover.
Rotate the two fuser oil roller lock
levers to release the fuser oil roller.
5"
26
Dispose of it properly
according to your local regulations.
Replacing the Fuser Oil Roller
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
3
Remove the new fuser oil roller from its shipping box.
Attention
If you set the new fuser oil roller on a table, do it
as shown in the illustration. Do not allow the
roller surface to contact the table or get dirty.
This could lower image quality.
4
5
6
Insert the new
fuser oil roller
installation guides
(front, rear) into
the fuser unit
installation rail.
Carefully lower the
roller.
Rotate the two oil roller levers
to lock the oil roller into place.
Attention
If the two fuser oil roller release levers are not correctly set, the
top cover cannot be closed. Set the release levers to the roller
fixed position.
7
Carefully close the top cover.
Check the release button to make sure the top cover is properly closed.
Replacing the Fuser Oil Roller
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
27
Replacing the Transfer Belt
When the transfer belt is at the end of its life, the message “REPLACE
TRANSFER BELT” appears, and the printer does not print. Replace the transfer belt. After the new transfer belt is installed, printing automatically resumes
(if you have not turned off the printer).
1
2
3
4
28
Open the printer’s front cover.
Remove the waste toner pack.
Rotate the left transfer belt
lock lever.
Remove the OPC drum cartridge and set it aside.
Replacing the Transfer Belt
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
Attention
The OPC drum is extremely sensitive to bright light and direct
sunlight. Always put it in its protective bag until you’re ready to
reinstall it. Any exposure to light should be avoided, or permanent
damage could result.
Also, handle the cartridge carefully by its sides so you don’t touch
the surface (the green part) of the drum. The drum is also extremely
sensitive to hand oils and scratches, both of which reduce print
quality.
5
6
Rotate the left lever to its
4 o’clock position.
Grasp the handles of the transfer belt and remove it.
5"
Dispose of it properly according to your local regulations.
Replacing the Transfer Belt
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
29
7
8
Remove the new transfer belt
from its packaging and insert it
into the printer.
Press on the transfer belt front
handle with one hand, take
the handle of the transfer belt
fixture with your other hand,
and pull the fixture straight
toward you.
5"
9
30
Dispose of it properly
according to your local
regulations.
Rotate the transfer belt lock
lever.
Replacing the Transfer Belt
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
10
11
12
13
14
Reinstall the OPC
drum cartridge.
Close the transfer
belt lock lever.
Check to make sure the
laser lens cover is firmly
seated.
Reinstall the waste
toner pack.
Close the front cover.
2
1
Replacing the Transfer Belt
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
31
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
Using Media
2
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
Introduction
This chapter provides information on handling, selecting, and storing media.
Refer to the Maintenance Guide for media specifications.
Media Handling
Before purchasing a large quantity of special media, do a trial printing
with the same media and check print quality. Check our web site
www.minolta-qms.com for a list of current approved media.
Attention
Do not use the media types listed below. These could cause poor print
quality, media jams, or damage to the printer.
Do not use media that is
„ Not approved
„ Meant for ink jet printers
„ Folded, embossed, warped, or wrinkled
„ Perforated or prepunched
„ Too slick, too coarse
„ Composed of foil or gilt
„ Coated with a processed surface (such as carbon paper, heat-sensitive
paper, heat-pressure paper)
„ Irregularly shaped (not rectangular); not uniform in size
„ Bound with glue, tape, or paper clips, or attached to ribbons, hooks, buttons, and so forth
Do not use envelopes that have
„ Sticky flaps
„ Metal clasps, fasteners, transparent windows, peel-off strips for sealing
„ Material that will melt, vaporize, offset discolor, or emit dangerous fumes
Do not use labels that have
„ Label(s) already peeled off
„ Labels that peel off easily
„ Glue or sealer that might come off
„ Material that will melt, vaporize, offset discolor, or emit dangerous fumes
34
Introduction
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
Media Types
Plain Paper
Formatting Format data within your application.
Input
Upper and
Optional
Trays
500 sheets of 20 lb bond (75 g/m²) paper (letter/
A4/legal) each; capacity for other weights varies
accordingly.
Multipurpose 150 sheets of 20 lb bond (75 g/m²) paper; capacity
Tray
for other weights varies accordingly.
Orientation Upper and
Optional
Trays
Simplex—Face up; Duplex—Face down
Multipurpose Simplex—Face down; Duplex—Face up
Tray
Type
Any standard or recycled office paper suitable for plain-paper
laser printers, such as
„ Hammermill Laser Print
„ Georgia-Pacific Microprint Laser 1000
„ Neusiedler Color Copy 90
„ Xerox 4024
Weight
16–24 lb bond (60–90 g/m²)
Duplexing
Up to 24 lb bond (90 g/m²)
Letterhead and Memo Media
Formatting Format letterhead or memo data within your application. Try printing your data on a plain sheet of paper first to check placement.
Input
Upper and
Optional
Trays
Up to 500 sheets
Multipurpose Up to 150 sheets
Tray
Orientation Upper and
Optional
Trays
Face up—top of page toward the right
Multipurpose Face down—top of page toward the printer side
Tray
Media Types
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
35
Type
Any standard or recycled office paper suitable for plain-paper laser
printers, such as
„ Hammermill Laser Print
„ Georgia-Pacific Microprint Laser 1000
„ Neusiedler Color Copy 90
„ Xerox 4024
Weight
16–24 lb bond (60–90 g/m²)
Duplexing
Upper and
Optional
Trays
Face down—top of page toward the right
Multipurpose Face up—top of page toward the printer side
Tray
Notes
Check your application documentation for other information about
printing on letterhead and memo media.
Thick Stock
Formatting Format the information to be printed on the thick stock within your
application. Try printing your data on a plain sheet of paper first to
check placement.
Input
Multipurpose Up to 50 sheets, depending on the thickness of the
Tray Only
media
Orientation Face down
Type
For information about thick stock media recommended for your
printer, go to www.minolta-qms.com/support, then click on Answer
Base, or contact Technical Support. See the Service & Support
Guide for a complete listing of support telephone numbers.
Weight
Simplex: 24–43 lb bond (90–163 g/m²)
Autoduplex: Up to 28 lb bond (105 g/m²)
Manual Duplex: 24 lb (90 g/m²) to 43 lb (163 g/m²) bond
Duplexing
Autoduplexing thick stock over 28 lbs (105 g/m²) is not supported.
Thicker stock may be manually duplexed.
Notes
You should test the number of sheets of thick stock the multipurpose tray can hold to ensure that its performance is acceptable.
43 lb (163 g/m²) bond is also referred to as 90 lb index stock.
36
Media Types
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
Envelopes
Formatting Your printer receives the instructions to print on envelopes from
your application.
„ Print on the front side only. Some parts of the envelope consist
of three layers of paper—the front, back, and flap. Anything
printed in these layered regions may be lost or faded.
„ See your application documentation for specific information on
printing envelopes.
Input
Multipurpose Up to 50, depending on the thickness of the enveTray Only
lopes
Orientation Face down
Type
Use common office envelopes approved for laser printing with
diagonal joints, sharp folds and edges, and ordinary gummed
flaps, such as
„ Commercial #10: Columbian Recycled COR02
„ International DL: Auto Fil #01914
Duplexing
Not supported
Notes
„ You can print only on the address side of the envelope.
„ Envelopes should be dry.
„ Do not preload or preseal envelopes.
Labels
Formatting Format label data within your application. Try printing your data on
a plain sheet of paper first to check placement.
Input
Multipurpose Up to 50 sheets, depending on the thickness of the
Tray Only
labels
Orientation Face down
Type
Use only labels recommended for laser printers, such as Avery
5260
Weight
16–90 lb (60–163 g/m²)
Duplexing
Not supported
Media Types
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
37
Notes
„ Avoid using labels with exposed adhesive; it may stick to the
transfer belt or the fuser roller, causing labels to peel off and
media jams to occur.
„ Adhesive label stock is supported only in letter or A4 sheets.
„ A label consists of a face sheet (the printing surface), adhesive,
and a carrier sheet
—
The face sheet must follow the plain paper specification.
—
The face sheet surface must cover the entire carrier
sheet, and no adhesive should come through on the surface.
„ You can print continuously with label paper. However, this could
affect the media feed, depending on the media quality and printing environment. If problems occur, stop the continuous print
and print one sheet at a time.
„ Check your application documentation for other information on
printing labels.
Postcards
Formatting Format postcard data within your application. Try printing your
data on a plain sheet of paper first to check placement.
Input
Multipurpose Up to 50 sheets, depending on the thickness of the
Tray Only
postcards
Orientation Face down
Type
Use only postcards recommended for laser printers
Weight
16–90 lb (60–163 g/m²)
Duplexing
Not supported
Notes
If the postcard is warped, press on the warped
area before putting in multipurpose tray.
Transparencies
Formatting Format the information to be printed on the transparencies within
your application. Try printing your data on a plain sheet of paper
first to check placement.
38
Media Types
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
Input
Location
Upper and Optional Trays
Multipurpose tray
Capacity
Up to 50 sheets, depending on the thickness of the
transparencies
If you have problems feeding 50 sheets, try loading only 5–10 sheets at a time. Loading a large
number of transparencies at a time may cause
static buildup, thus causing feeding problems.
Orientation Upper and
Optional
Trays
Face up
Multipurpose Face down
Tray
Type
Use any full-color transparencies (also known as OHP film) that
meet normal photocopier standards. We recommend
„ Q-Media Transparency Media for the magicolor 2200 Series for
color printing
„ Q-Media Transparency Media for the magicolor 2200 Series for
monochrome printing
„ 3M PP2500 for monochrome printing
Duplexing
Not supported
Notes
„ If you touch the face of transparencies with your bare hands,
print quality may be affected.
„ Do not handle transparency media too much. Do not fan transparency media before loading it. Resulting static electricity may
cause printing errors.
„ Keep the media path clean. Transparencies are especially sensitive to a dirty media path. If there are shadows on either the
top or the bottom of the sheets, see “Cleaning the Printer Interior” in the Maintenance Guide.
„ You can print continuously with transparencies. However, this
could affect the media feed, depending on the media quality
and printing environment. If problems occur, stop the continuous print and print one sheet at a time.
„ Check your application documentation for other information
about printing on transparencies.
Media Types
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
39
Loading Media
Take off the top and bottom
sheets of a ream of paper. Holding a stack of approximately 250
sheets at a time, fan the stack to
prevent static buildup for the
paper before inserting it in a tray.
5"
OHP
Do not fan transparency media.
Attention
Always load the media short edge first.
Attention
Do not mix media of different sizes, types, or weights, as this will cause
printer jamming.
„ When refilling media, first remove any media remaining in the tray. Stack
it with the new media, even the edges, then reload it. Although the magicolor 2210 was designed for printing on a wide range of media types, it is
not intended to print exclusively on a single media type except plain
paper. Continuous printing on media other than plain paper (such as
envelopes, labels, thick stock, or transparencies) may adversely affect
print quality or reduce engine life.
„ For media other than standard plain paper or transparencies, both the
driver (Paper tab, Paper Type option) and the MP Size key on the control
panel need to be selected.
It is important to use the MP Size key to set the multipurpose tray to the
appropriate media size in order to obtain optimum printing results.
Autoduplexing
Duplex (2-sided) printing can be done automatically with the optional duplex
unit installed.
5"
40
Only up to 24 lb (90g/m²) plain paper can be duplexed.
Loading Media
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
If you are printing duplex from the upper or optional tray, load the media printing-side down with the top of the media (or letterhead or memo information)
toward the right side of the tray. If you are printing duplex from the multipurpose tray, load the media printing-side up with the top of the media toward the
printer.
5"
The options in the driver are Simplex (1-sided pages), or Long Edge
(flipped horizontally as in a loose-leaf notebook), or Short Edge
(flipped vertically as on a clipboard).
Upper and Optional Media Trays
1
2
Slide the media tray open.
Push the media pressure plate
down to lock it in position.
Loading Media
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
41
3
Adjust the media guides to fit the size paper you’re loading.
Squeeze the retainers, move the guides to the appropriate location
(media sizes are listed on the tray), and release the retainers. The media
should fit easily between the guides.
4
Load the paper face-up, short
edge toward the right of the tray.
Often, an arrow on the media
package label indicates the
printing-side of the media.
Do not overfill the tray.
A fill limit mark is provided on
the inside of the tray. The
media tray holds 500 sheets
of 20 lb bond (75 g/m²) paper.
42
Loading Media
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
Make sure that the paper fits
easily between the guides and
the paper corners are under the
left and right media-separating
tabs and are not bent.
Attention
Always readjust the media guides after inserting the media.
Improperly adjusted guides may cause poor print quality, media
jams, or printer damage.
5
Slide the tray back into
the printer.
5"
If you have
removed the tray
from the printer,
slightly tilt up the
tray to insert it
into the installation
rails to slide it
back in.
Multipurpose Tray
Page sizes other than letter, A4, and legal can be printed only from the multipurpose tray (also known as tray 1). Use the MP (Multipurpose) Size key on
the control panel to set the page size.
Other special types of media (such as thick stock, transparencies, and envelopes) are also fed from the multipurpose tray. See “Media Specifications” in
the Maintenance Guide for more information about media.
Loading Media
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
43
1
2
Open the multipurpose tray on
the right side of the printer.
Open the media support.
Attention
Load only one type/size of media per tray at a time.
Load the media face down, short edge toward the printer.
FA
C
DO E
WN
3
44
Loading Media
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
Often, an arrow on the paper
package label indicates the
face-up (printing) side of
the paper.
A fill limit mark is provided on the
inside of the media guides on the
multipurpose tray. The multipurpose tray holds 150 sheets of
20 lb bond (75 g/m²) paper.
4
Adjust the media guides to fit the
size media you’re loading.
LTR
LG .
EXE. L.
A5
B5
A4
Attention
Always adjust the media guides after inserting the media. A guide
that is not properly adjusted can cause poor print quality, media
jams, or printer damage.
5
Specify the media size in the multipurpose tray by using the MP Size key
on the control panel.
Printing Envelopes from the Multipurpose Tray
1
2
3
Flex the envelope stack (including the edges) to remove any stiffness.
Place the envelopes on a flat surface, and flatten them by pressing down
the corners.
Correct any bent corners, and then tap the envelopes on a flat surface to
align them.
Loading Media
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
45
4
Place the envelope stack into the multipurpose tray with the flap-side up.
Check your application documentation to determine if the flap should be
placed on the left or on the right. Print a single envelope to check the orientation before printing multiple copies.
5
Adjust the media guides to the width of the envelopes.
Make sure the guides are snug enough to keep the envelopes straight,
but not so tight that they buckle the envelopes.
6
Open the flap of each envelope immediately (before it cools) after the
envelope is delivered to the output tray.
5"
Because the envelopes pass through heated rollers, the gummed
area on the flaps may seal. Using envelopes with emulsion-based
glue avoids this problem.
Printing Area
The printing area on all media sizes is up to
about 0.157 inch (4 mm) from the edges of the
media.
Media Storage
When storing media, avoid:
„ Direct sunlight
„ Excess heat and humidity
„ Dust
If media has been removed from its wrapper, place it in its original packaging
and store in a cool, dark place on a level surface.
46
Media Storage
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
Maintaining the
Printer
3
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
Maintaining the Printer
Handle the printer with care to preserve its life. Abuse may cause damage
and void your warranty. If dust and paper scraps remain on the inside or outside of the printer, printer performance and print quality will suffer, so the
printer should be cleaned periodically. Keep the following guidelines in mind:
WARNING!
Turn off the printer, unplug the power cord, and disconnect all interface
cables before cleaning. Do not spill water or detergent into the printer;
otherwise the printer will be damaged and an electric shock may occur.
ACHTUNG! Ziehen Sie den Netzstecker aus der Steckdose bevor Sie
den Drucker reinigen. Verschütten Sie kein Wasser oder andere
Flüssigkeiten auf dem Drucker, da das Gerät sonst beschädigt wird
oder die Gefahr eines elektrischen Schlages besteht.
If you have an optional 5-bin mailbox installed, turn the printer off first,
then turn off the mailbox.
„ Either clean the printer before use, or allow time after unplugging it to
allow the fuser unit to cool down.
Attention
The fuser unit is hot. When the top cover is opened,
the fuser unit temperature drops gradually (one hour
wait time).
„ Be careful when cleaning the inside or removing paper jams, as the fuser
unit and other internal parts may become very hot.
„ Do not place anything on the top of the printer.
„ Use a soft cloth to clean the printer.
„ Never spray cleaning solution directly on the printer’s surface; the spray
could penetrate through the air vents of the printer and damage the internal circuits. Avoid using abrasive or corrosive solutions or solutions that
contain solvents, (such as alcohol and benzene) to clean the printer.
„ Always test any cleaning solution (such as mild detergent) on a small area
of your printer to check the solution's performance.
„ Never use sharp or rough implements, such as wire or plastic
cleaning pads.
„ Always close the printer covers gently. Never expose the printer
to vibrations.
48
Maintaining the Printer
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
„ Do not put a cover on the printer immediately after using it. Turn it off and
wait until it cools down.
„ Do not leave the printer’s covers open for any length of time, especially in
well-lit places; light may damage the OPC drum cartridge.
„ Do not open the printer during printing.
„ Do not tap paper stacks on the printer.
„ Do not tilt, lubricate, or disassemble the printer.
„ Do not touch the electrical contacts, gears, or laser beam devices. Doing
so may damage the printer and cause the print quality to deteriorate.
„ Keep media in the output tray at minimum level. If the media stacks too
high, your printer may experience media jams and excessive media curl.
„ Lift the printer from the bottom only, using the carrying grips and the
carrying bars. Make sure two people are available to lift the printer when
moving it.
When moving the printer, keep the printer level to avoid toner spillage.
„ If you get toner on your skin, wash it off with cool water and neutral
detergent.
WARNING!
If you get toner in your eyes, wash it out immediately with cool water
and consult a doctor. Material Safety Data Sheets (MSDS) information
can be found at www.minolta-qms.com (click on the Answer Base).
ACHTUNG! Sollte Toner in Ihre Augen gelangen, die Augen unbedingt
sofort mit kaltem Wasser ausspülen und einen Artzt aufsuchen.
MSDS-Informationen (Material Safety Data Sheets; Datenblätter zur
Materialsicherheit) finden Sie im Internet unter www.minolta-qms.com
(klicken Sie auf “Answer Base”). Read all caution and warning labels
carefully, making sure to follow any instructions contained in them.
These labels are located on the inside of the printer’s covers and the
interior of the printer body.
„ Make sure any parts removed during cleaning are replaced before you
plug in the printer.
See “Repacking the Printer” on page 143 for printer storing and shipping
instructions.
Maintaining the Printer
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
49
Cleaning
You should perform a thorough cleaning every 30,000 single-sided pages,
every 12 months, or as needed, whichever comes earlier.
Always test any cleaning solution (such as a mild detergent) on a small area
of your printer to check the solution’s performance
Outside the Printer
Use
Avoid
A soft dry cloth to clean the
control panel
Sharp or rough implements (such as wire or
plastic cleaning pads). Any liquid
A soft damp cloth to clean
the printer exterior
Sharp or rough implements (such as wire or
plastic cleaning pads)
Mild detergent to clean the
printer exterior
Abrasive or corrosive solutions that contain
solvents (such as alcohol or benzine)
Inside the Printer
This item needs
cleaning...
After...
Laser lens cover
Removing the waste toner pack to User
clean around it or to replace it.
See the MainteEvery 30,000 single-sided pages, nance Guide.
Duplex unit paper
guides or rollers
OPC drum cartridge
By...
every 12 months, or as needed,
whichever comes earlier.
Paper exit rollers
Printer interior
Registration roller
Transfer roller
50
Cleaning
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
Troubleshooting
4
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
Introduction
This chapter provides information to aid you in resolving printer problems you
may encounter, or at least guide you to the proper sources for help.
Printing a Status Page
Print a status page to verify the printer is printing correctly.
Press Key
(Until) Display Reads
Online
IDLE (and online LED is off)
Menu
OPERATOR CONTROL
Next (
)
ADMINISTRATION
Select
ADMINISTRATION–SPECIAL PAGES
Select
PRINT STATUS
Select
YES
Online
IDLE (and online LED is on)
Preventing Media Jams
52
Make sure that...
Avoid...
Media matches the printer specifications
Media that is folded, wrinkled, or
excessively curled
Media is flat, especially on the leading edge
Double feeding (remove the media
and fan the sheets—they may be
sticking together)
The printer is on a hard, flat, level
surface
Fanning transparencies since this
causes static
You have the correct media type
selected if you’re printing on envelopes, labels, thick stock, or transparencies.
Loading more than one type/size/
weight of media in a tray at the
same time
You store media in a dry location
away from moisture and humidity
Overfilling the media input trays
Introduction
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
Make sure that...
Avoid...
You always adjust the media width
regulation guides in the multipurpose tray after inserting the media
(a guide that is not properly
adjusted can cause poor print quality, paper jams, or printer damage)
Allowing the output tray to overfill
(the face-down output tray has a
500-sheet capacity—jamming may
occur if you allow media to accumulate more than 500 sheets at a time)
You remove transparencies from
the output tray immediately to avoid
static buildup.
You load the media (for single-sided
pages) printing-side up in the upper
or optional trays or printing-side
down in the multipurpose tray (many manufacturers
place an arrow on the end of the
wrapper to indicate the printing
side—if you can’t determine which
side of the media to print on,
remove the media from the tray,
rotate the stack a half-turn, turn the
stack over, and then place it back in
the tray)
Automatic Jam Recovery
The magicolor 2210 provides automatic jam recovery (when enabled through
the Administration/Engine/Page Recovery menu). After you remove any
jammed media, printing automatically resumes from the page the printer
stopped at when the jam occurred.
5"
For automatic jam recovery to work, it is necessary to leave the printer
turned on when you remove the jammed media.
Automatic Jam Recovery
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
53
Understanding the Media Path
Understanding the printer’s media path will help you locate media jams.
c
d
e
f
g
h
i
j
k
l
Media exit unit
Output tray
Fuser
Transfer belt
OPC drum cartridge
Duplex unit (optional)
Multipurpose tray
Upper media tray
Lower feeder unit (LFU) and optional tray (optional)
5-bin mailbox (optional)
c
Model with d
e
LFU
f
g
h
i
j
k
Model with
LFU and
Mailbox
l
Simplex
Duplex
54
Understanding the Media Path
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
Media Tray (Standard Upper Tray and Optional Tray)
The media tray(s) is (are) located at the bottom front of the printer. The media
is picked from the tray, passed under the OPC drum cartridge and the
transfer belt, passed through the fuser, and delivered via the paper exit unit
to the output tray on top of the printer.
Lower Feed Unit (LFU) Tray(s)
The LFU media tray(s) is (are) located at the bottom front of the printer in the
lower feeder unit(s). The media fed through the LFU is picked and delivered
to the output tray the same way as media from the standard upper tray.
Multipurpose Tray
The multipurpose tray is located at the right of the printer. The media is
picked from the multipurpose tray, passed under the OPC drum cartridge and
the transfer belt, passed through the fuser, and delivered via the paper exit
unit to the output tray on top of the printer.
Duplex Unit (Optional)
The media is picked from a media tray, passed under the transfer belt,
passed through the fuser, fed into the duplex unit where the media undergoes
a change in direction, cycles through the transfer belt and fuser again, and is
delivered via the paper exit unit to the output tray, which is the top of the
printer. Since several sheets cycle through the printer/duplex unit at the
same time, recovering from a media jam may require the removal of more
than one sheet.
To manually duplex, remove the media, flip it over, and reload it.
5-bin Mailbox (Optional)
The 5-bin mailbox is located on the top of the printer. The media is picked
from the tray, passed under the transfer belt, passed through the fuser, and
delivered via the paper exit unit to the 5-bin mailbox, which is on top of the
printer.
Clearing Media Jams
To avoid damage, always remove jammed media gently, without tearing it.
Any pieces of media left in the printer, whether large or small, can obstruct
the paper path and cause further jams. Do not reload media that has jammed.
Clearing Media Jams
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
55
Attention
The image is not fixed on the media before the fusing process. If you
touch the printed surface, the toner may stick to your hands, so be
careful not to touch the print face when removing the jammed media.
Make sure not to spill any toner inside the printer. Unfused toner can
dirty your hands, clothes, or anything else it gets on. If you accidentally
get toner on your hands, wash them in cool water. If you accidentally
get toner on your clothes, lightly dust them off as much as possible. If
some toner remains on your clothes, use cool, not hot water, to rinse
the toner off, provided your clothing is washable. If toner gets on your
skin, wash it off with water or a neutral detergent.
WARNING!
If you get toner in your eyes, wash it out immediately and consult a
doctor. Material Safety Data Sheets (MSDS) information can be found at
www.minolta-qms.com (click on the Answer Base).
ACHTUNG! Sollte Toner in Ihre Augen gelangen, die Augen unbedingt
sofort mit kaltem Wasser ausspülen und einen Artzt aufsuchen.
MSDS-Informationen (Material Safety Data Sheets; Datenblätter zur
Materialsicherheit) finden Sie im Internet unter www.minolta-qms.com
(klicken Sie auf “Answer Base”).
If, after clearing the media jam, the jam message in the control panel window
persists, open and close the printer’s covers. This should clear the jam
message.
Handling Media Jams by Location
56
Location of Jam
Page Reference
Tray 1—multipurpose tray
Page 58
Tray 2—upper tray
Tray 5—optional tray (lower feeder unit)
Page 57
Near the OPC drum
Page 59
Near the duplex unit
Page 62
In the mailbox
Page 65
In the output tray
Page 66
Clearing Media Jams
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
Clearing Misfeed (Upper or Optional Tray) Jams
1
2
3
4
Remove the media tray(s).
Carefully remove the jammed
media.
Shuffle the media currently in
the tray and even up the front edges.
Reinsert the media printing face up.
Make sure the media is lying flat, is under the
media separating tabs, and doesn’t exceed
the media limit mark. Check to see if the
media width guides are correct.
5
6
Slide the tray(s) back into the
printer.
Open the front cover, then
close it.
The media jam message is no
longer displayed in the printer
message window.
Clearing Media Jams
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
57
Clearing Misfeed (Multipurpose Tray) Jams
1
2
3
4
Remove the media from in the multipurpose tray.
Carefully remove the jammed media.
Shuffle the media that was removed in
step 1 and even up the front edges.
Reinsert the media printing face down.
Make sure the media is lying flat and doesn’t
exceed the media limit mark. Check to see if
the media width guides are correct.
5
Open the front cover, then close it.
The media jam message is no longer displayed in the printer message
window.
Clearing Inner Jams, Outer Jams, and Drum Jams
Media Jams inside the Lower Right Door (Vertical
Transport Area)
1
2
3
Open the lower right door(s).
Carefully remove the jammed
media.
Close the lower right door(s).
The media jam message is no
longer displayed in the printer
message window.
58
Clearing Media Jams
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
Media Jams near the OPC Drum
1
2
3
If there is any media in the multipurpose
tray, remove it and close the multipurpose
tray.
Press the right-side cover release button
and carefully open the cover all the way.
Remove the jammed
media by pulling it slowly
from the bottom of the
fuser.
Attention
Do not pull jammed media from the
top of the printer through the fusing
rollers.
This prevents any unfused toner
from dirtying the fuser rollers.
Clearing Media Jams
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
59
4
Close the right-side cover.
The media jam message is no longer displayed in the printer message
window.
5
6
7
8
Check the release button to make sure the cover is securely closed.
If media was removed in step 1, open the multipurpose tray.
Shuffle the media that was removed in
step 1 and even up the front edges.
Reinsert the media printing face down.
Make sure the media is lying flat and
doesn’t exceed the media limit mark.
Check to see if the media width guides
are correct.
Media Jams near the Duplex Unit (Optional)
1
Open the top cover.
Attention
Do not pull jammed media from
the top of the printer through the
fusing rollers.
This prevents any unfused toner
from dirtying the fuser rollers.
60
Clearing Media Jams
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
2
3
4
5
6
Carefully remove the jammed
media in the top cover media
reverse area.
Open the media jam removal cover
with your left hand and carefully
remove the jammed media in the
duplex media feed area with your
right hand.
Close the media jam removal cover
with your left hand and close the
top cover.
Check the release button to make
sure the door is securely closed.
If the multipurpose tray is
closed, open it.
Clearing Media Jams
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
61
7
8
9
10
11
Pressing the duplex unit cover release,
carefully open the cover.
Remove the jammed media.
Close the duplex unit’s cover.
Close the multipurpose tray.
If there still is a jam message,
press the right-side cover release
button and carefully open the
cover all the way.
12
Lift the inner paper guide.
13
Remove the jammed media by pulling it toward you.
If the media came out easily, skip ahead to step 15.
If the media did not come out easily or if you cannot reach the media from
this area, keep the duplex unit’s lower cover open.
62
Clearing Media Jams
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
14
15
Open the duplex unit cover.
Remove the jammed media by pulling it slowly from the bottom of the
fuser rollers.
Be careful not to touch the transfer belt while removing jammed media.
16
17
Close the printer’s top cover.
Close the duplex unit’s paper guide, lower cover, and top cover.
The media jam message is no longer displayed in the printer message
window.
Media Jams near the Fuser Unit
1
Open the top cover.
Attention
Do not pull jammed media from
the top of the printer through the
fusing rollers.
This prevents any unfused toner
from dirtying the fuser rollers.
2
3
4
Carefully remove the jammed
media through the media jam
removal cover.
Open the media jam removal cover
and carefully remove the media that
is jammed there.
Close the media jam removal cover.
Clearing Media Jams
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
63
5
Close the top cover.
Check the release button to make sure the top cover is securely closed..
6
7
Open the right-side cover.
Remove the jammed media by pulling it slowly from the bottom of the
fuser.
Be careful not to touch the transfer
belt while removing jammed media.
8
Close the right-side cover.
Check the release button
to make sure the duplex unit
cover is securely closed.
The media jam message is no
longer displayed in the printer
message window.
64
Clearing Media Jams
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
Media Jams in the Optional 5-bin Mailbox
1
2
3
Carefully remove the jammed
media from the paper eject area
of the mailbox.
Open the mailbox door.
Lift up the paper jam removal
guide in the mailbox with your left
hand, and use your right hand to
carefully remove the jammed paper.
Clearing Media Jams
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
65
4
Close the mailbox door.
The media jam message is no
longer displayed in the printer
message window.
Media Jams in the Output Tray
Remove jammed media from the output tray by gently pulling it to the left
away from the media exit area.
Solving Problems with Media Jams
5"
Frequent jams in any area indicate that area should be checked,
repaired, or cleaned. Repeated jams may also happen if you’re using
the wrong weight print media.
Symptom
Cause
Solution
Several
sheets go
through
the printer
together.
The front edges of
the media are not
even.
Remove the havemedia and even up
the front edges, then reload it.
The media is moist
from humidity.
Remove the moist media and replace it
with new, dry media.
Paper jam
message
stays on.
Front cover needs
to be opened and
closed again to
reset the printer.
Open and close the front cover of the
printer again.
Some media
remains jammed in
the printer.
Recheck the paper path and make sure
you have removed all of the media
jams.
5-bin mail- The wrong media
box jams. is being used.
Make sure that you are using only plain
paper (or recycled plain paper).
Make sure that you are using only
letter/A4 plain paper.
66
Solving Problems with Media Jams
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
Symptom
Cause
Solution
Duplex
unit jams.
The wrong media
is being used.
Use only supported media. Refer to the
“Media Types” on page 35.
Plain paper and thick stock up to 28 lb
bond (105 g/m²) can be autoduplexed if
the optional duplex unit is installed. For
heavier weights, manual duplexing is
required. To manually duplex, remove
the media, flip it over, and reload it.
Make sure that you have not mixed
media types in your multipurpose tray.
Do not duplex envelopes, glossy
stock, labels, transfer media, or
transparencies.
Media may still be
jammed.
Check for media stuck in the paper
guides in the duplex unit’s top cover,
and the media supply area on the lower
left of the printer.
If you removed jammed media from
near the OPC drum, reset the OPC
drum’s locking levers.
Media is
jamming.
The media is not
correctly positioned
in the tray.
Remove the jammed media aand
reposition the media properly in the tray.
The number of
sheets in the tray
exceeds the maximum allowed.
Remove the excess media and reload
the correct number of sheets in the tray.
The width regulation guides are not
correctly adjusted
to the media size.
Adjust the regulation guides in the tray
to match the size of the media.
The media in upper
or optional tray is
not under the
media separating
tabs.
Remove the media and reload it so
the front corners are under the media
separating tabs.
Warped or wrinkled media is
loaded in the tray.
Remove the media, smooth it out, and
reload it. If it still jams, do not use that
media.
Solving Problems with Media Jams
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
67
68
Symptom
Cause
Solution
Media is
jamming.
Labels, letterhead,
envelopes, postcards, thick stock,
or transfer material
are loaded in the
upper or optional
tray.
Special media must be loaded in the
multipurpose tray only.
The recommended
transparency
(OHP) or label
paper is facing the
wrong way in the
multipurpose tray.
Load the transparencies or labels
according to the manufacturer’s
instructions.
Envelopes are facing the wrong way
in the multipurpose tray.
Load the envelopes in the multipurpose
tray so the the flaps are facing up.
Multiple sheets of
transparency
(OHP) media are
collecting static
electricity in the
tray.
Remove the OHP media and load them
in the tray one sheet at a time. Do not
fan transparencies before loading them.
The media is moist
from humidity.
Remove the moist media and replace it
with new, dry media.
Unsupported
media (wrong size,
thickness, type,
etc.) is being used.
Use media that is covered by the printer
warranty.
Media supply roller
is dirty.
Clean the media supply roller.
If the flaps are on the short edge, set
the envelopes in the multipurpose tray
so that the flaps are on the printer side.
Solving Problems with Media Jams
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
Solving Other Problems
Symptom
Cause
Solution
Printer
power is
not on.
The power cord is
not correctly
plugged into the
outlet.
Turn the power switch off (O position),
then remove the power cord from the
outlet and plug it back in.
The mailbox power
cord is not correctly
connected.
Turn the power switch and the mailbox
power switch off (O position), then
reconnect the mailbox power cord using
the procedure below:
—Connect the mailbox power cord plug
end to the mailbox power socket (lower
connection).
—Connect the mailbox power cord
socket end to the printer power plug.
—Connect the printer power cord
socket end to the mailbox power plug
(upper connection).
—Plug the printer power cord into the
outlet.
Something is
wrong with the outlet you are using
for the printer.
Plug another electrical appliance into
the outlet and see whether it operates
properly.
The power switch
is not correctly
set to the On (I)
position.
Set the power switch to the Off (O)
position, then set it back to the On (I)
position.
Something is
wrong with the outlet you are using
for the printer.
Plug another electrical appliance into
the outlet and see whether it operates
properly.
Turn the printer power switch and the
mailbox power switch to the Off (O)
position, then turn on the power again
using the procedure below:
—Turn the mailbox power switch on.
—Turn the printer power switch on.
Solving Other Problems
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
69
Symptom
Cause
Solution
Printer
power is
not on.
The printer is connected to an outlet
with a voltage or
frequency that
does not match the
printer specifications.
Use a power source with the following
specifications:
—Power
Japan: 100 VAC 50–60 Hz 12 amps
North America: 120 VAC 50–60 Hz
8 amps
Europe: 220-240 VAC 50–60 Hz
6 amps
Latin America: 120 VAC 50–60 Hz
8 amps
220-240 VAC 50–60 Hz 6 amps
—Voltage fluctuation
Japan: 100 VAC ±10%
North America: 120 VAC ±10%
Europe: 220-240 VAC ±10%
Latin America: 120 VAC ±10%
220-240 VAC ±10%
—Frequency fluctuation rate within
50/60 ±3 Hz
Note: If you experience problems, the first thing you want to do is print a
status page.
You can’t Is the printer off line
print a sta- before you try to
tus page. enter the Administration/Special
Pages/ Print
Status menu?
70
Turn the printer off line before printing a
status page.
The tray does not
have media.
Check that the media trays are loaded
with media, in place and secure.
The printer’s covers aren’t closed
securely.
Make sure the front and top covers are
closed securely. Close all covers gently
to avoid jarring the printer. Make sure
the waste toner pack in installed
correctly.
There is a media
jam.
Check for a media jam.
Solving Other Problems
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
Symptom
Cause
Solution
Data was
sent to the
printer,
but it
doesn’t
print.
An error message
is displayed in the
message window.
Handle according to the message
displayed.
The transfer belt
installation guide is
not set correctly in
the installation rail.
Remove the transfer belt. Place the
front end of the intermediate transfer
unit installation guide (2 locations)
correctly in the installation rail. Next,
lightly push in the unit. Carefully insert
the transfer belt about 6 inches (152.4
mm). Let go with your right hand that
was holding the top handle of the transfer belt, hold the front handle with both
hands, and carefully push in.
Data
indicator
stays on.
Too many typefaces are being
downloaded at the
same time.
Make sure you have enough printer
memory.
Printer
resets.
Occasionally, software applications
interfere with each
other.
Some applications send a printer prep
file to the printer at the beginning of
each document. When this occurs,
other prep files cannot be sent without
resetting the printer. Monitor your
activities to see if there is a correlation
between your use of a certain
application and the printer resetting. If
so, contact the application developer.
Downloading too
many typefaces
can overload the
printer memory and
cause the printer to
reset to default.
Additional memory (RAM) or a hard
drive, which can be used for font
storage, is available and easily
installed.
Solving Other Problems
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
71
72
Symptom
Cause
Solution
Printing
takes too
much
time.
The printer is set to
a slow printing
mode (for example,
for OHP, thick
stock, or some
other special kind
of media).
It takes more time to print with special
media. When using regular paper, make
sure that the media type is set properly
in the driver.
The printer is set to
power saving
mode.
It takes a little time for printing to start in
power saving mode. If you do not want
to use this mode, disable it.
The printer memory is insufficient.
Add more memory.
A blank
startup
page
ejects or
blank
pages
come out
during a
printing
job.
One or more of the
toner cartridges is
defective, empty, or
missing.
Check the toner cartridges. The image
does not print if the cartridges are
empty.
The wrong media
is being used.
Check that the media type set in the
driver matches the media loaded in the
printer.
Not all
pages
print.
The printer could
have the wrong
kind of cable, or
your printer may
not be configured
for the correct
cable and port.
Check your cable.
The Cancel key
was pressed.
Make sure no one pressed the Cancel
key while your job was printing.
The media tray is
empty.
Check the message window to see if
the tray you are using is out of media.
If the toner cartridges are not empty
and blank pages are ejecting, take each
cartridge out, rock it from side to side,
and reinstall it in the printer.
Solving Other Problems
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
Symptom
Cause
You are
Media or settings
experienc- are not correct.
ing problems
duplexing.
Solution
Make sure that you are using only plain
paper. Do not duplex envelopes, glossy
stock, labels, postcards, transfer media,
or transparencies. Make sure that you
have not mixed media types in your
multipurpose tray.
Make sure that your document has
more than one page.
Go into the printer’s control panel and
make sure that duplex is an available
option.
In the printer driver, choose Short Edge
(flipped as on a clipboard) or Long Edge
(flipped as in a loose-leaf notebook).
Make sure that you are using correct
media.
Make sure that all of the covers are
closed. Open and then close the covers
to confirm that they are securely closed.
If you turned the printer off, make sure
that you have turned the printer on
again and waited for it to warm up
Transfer
belt cannot be
removed.
The OPC drum unit
is installed.
Remove the OPC drum unit first, then
remove the transfer belt.
The transfer belt
left release lever is
not set in the transfer belt removal
position.
Turn the transfer belt left release lever
clockwise to the 4 o’clock position, then
remove the transfer belt.
The
printer
pauses.
The printer pauses
for the Auto-Image
Density Control
(AIDC) cycle.
After 100 1-sided pages of a continuous
print run, the magicolor 2210 automatically pauses to do an AIDC cycle. This
process is provided to make sure
reliable printer operation with optimum
output quality.
Solving Other Problems
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
73
Solving Problems with Printing Quality
Symptom
Cause
Solution
Nothing is
printed.
One or more of the toner
cartridges is damaged.
Remove the toner cartridge and check
for damage. If necessary, replace it.
The driver is not set
correctly.
Select the proper setting in the driver to
switch from transparency (OHP) film to
plain paper.
The OPC drum cartridge is
damaged.
Remove the OPC drum cartridge and
check for damage. If necessary, replace
the entire drum kit.
The transfer roller unit is
misinstalled.
Reset the transfer roller unit.
The media is moist from
humidity.
Adjust the humidity for paper storage.
Remove the moist media and replace it
with new, dry media.
The media set in the driver
mismatches the media
loaded in the printer.
Load the correct media in the printer.
Image is
too light;
there is
low image
density.
Image darkness sensor is
dirty.
Open the front cover. Lift up the transfer
belt release lever to the 12 o’clock position. Next, return the lever to the 3
o’clock position. Repeat this operation
several times. (This cleans the surface
of the image darkness sensor.)
ABCDE
ABCDE
ABCDE
ABCDE
The media is moist from
humidity.
Remove the moist media and replace
with new, dry media.
There is not much toner
left in the cartridge.
Remove the toner cartridge and gently
rock it horizontally five or six times to
redistribute the toner.
Replace the toner cartridge.
74
One or more of the toner
cartridges is defective.
Remove the toner cartridges and check
for damage. If necessary, replace it.
Media type may be set
incorrectly.
Envelopes, glossy stock, labels, transfer media, and thick stock have to be
set in the thick stock mode.
The image transfer unit
may be misinstalled or
defective.
Reinstall the image transfer unit. If necessary, replace it.
Solving Problems with Printing Quality
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
Symptom
Cause
Solution
Image is
too light;
there is
low image
density
(continued).
Image darkness
(Auto-Image Density Control [AIDC]) sensor is dirty.
Open the front cover. Lift up the transfer
belt release lever to the 12 o’clock position. Next, return the lever to the 3
o’clock position. Repeat this operation
several times. (This cleans the surface
of the image darkness sensor.)
The print
contains
light or
whited out
areas.
Media may be moist.
Remove the moist media and replace it
with new, dry media.
Humidity may be too high.
Adjust the humidity in the paper storage
area.
The fuser unit may be
defective.
Check the fuser unit for damage. If necessary, replace it.
The OPC drum cartridge is
damaged.
Remove the OPC drum cartridge and
check for damage. If necessary, replace
the entire drum kit.
The transfer roller unit is
misinstalled.
Reset the transfer roller unit.
One or more of the toner
cartridges is damaged.
Remove the toner cartridge and check
for damage. If necessary, replace it.
The OPC drum cartridge is
damaged.
Remove the OPC drum cartridge and
check for damage. If necessary, replace
the entire drum kit.
The transfer unit is misinstalled.
Make sure that the transfer unit was
correctly installed.
The transfer roller is damaged.
Replace the transfer roller.
The printer is not
on a level enough surface.
Level the printer (not exceeding 1.5°
slant at any point around the machine).
ABCDE
ABCDE
ABCDE
ABCDE
Horizontal white
lines
appear in
image.
Printouts
seem
faded on
one side.
Solving Problems with Printing Quality
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
75
Symptom
Cause
Solution
Irregular
print or
mottled
image
appears.
The media is moist from
humidity.
Remove the moist media and replace it
with new, dry
media.
There is
insufficient
fusing or
the
image
comes off
when
rubbed.
The media is moist from
humidity.
Remove the moist media and replace it
with new, dry media.
Media with specifications
not covered by the printer
warranty is being used.
Use media that is covered by the printer
warranty.
Your media type may be
incorrectly set.
Envelopes, glossy stock, labels, transfer media, and thick stock have to be
set in the Thick Stock mode.
One or more of the toner
cartridges may be near
empty or damaged.
Remove the toner cartridges and gently
rock them five or six times to redistribute the toner. Then, reinstall the cartridges.
The print
or color
density
may be
uneven.
Install new toner cartridges.
The OPC drum may have
misinstalled or defective.
76
Reinstall the OPC drum cartridge. If
necessary, replace the entire drum kit.
Solving Problems with Printing Quality
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
Symptom
Cause
Solution
Image is
blurred;
background is
lightly
stained;
there is
insufficient
gloss
of the
printed
image.
One or more of the toner
cartridges is defective.
Check the toner cartridges. If necessary, replace them.
The OPC drum may be
misinstalled or defective.
Reinstall the OPC drum cartridge. If
necessary, replace the entire drum kit.
Background is
foggy.
One or more of the toner
cartridges is defective.
Remove the toner cartridge and check
for damage. If necessary, replace it.
The OPC drum cartridge is
damaged.
Remove the OPC drum cartridge and
check for damage. If necessary, replace
the entire drum kit.
Entire
sheet is
printed in
black or
color.
One or more of the toner
cartridges is defective.
Remove the toner cartridge and check
for damage. If necessary, replace it.
The OPC drum cartridge is
damaged.
Remove the OPC drum cartridge and
check for damage. If necessary, replace
the entire drum kit.
Solving Problems with Printing Quality
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
77
Symptom
Cause
Solution
Part of
image is
missing.
The media is moist from
humidity.
Remove the moist media and replace it
with new, dry media.
Media with specifications
not covered by the printer
warranty is being used.
Use media that is covered by the printer
warranty.
One or more of the toner
cartridges is defective.
Remove the toner cartridge and check
for damage. If necessary, replace it.
The OPC drum cartridge is
damaged.
Remove the OPC drum cartridge and
check for damage. If necessary, replace
the entire drum kit.
One or more of the toner
cartridges is defective.
Remove the toner cartridge and check
for damage. If necessary, replace it.
The OPC drum cartridge is
damaged.
Remove the OPC drum cartridge and
check for damage. If necessary, replace
the entire drum kit.
The toner in one or more
of the toner cartridges is
uneven.
Remove the toner cartridges and gently
rock them five or six times to redistribute the toner. Then, reinstall the cartridges.
The OPC drum cartridge is
damaged.
Remove the OPC drum cartridge and
check for damage. If necessary, replace
the entire drum kit.
Image is
too dark.
Dark
tones are
uneven.
78
Solving Problems with Printing Quality
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
Symptom
Cause
Solution
There are
toner
smudges
or residual
images.
One or more of the toner
cartridges is misinstalled
or defective .
If the toner smudges are on only the
front of the page:
„ Remove the toner cartridges and
gently rock them five or six times to
redistribute the toner. Then, reinstall
the cartridges.
„ One or more toner cartridges may be
defective. Check the toner cartridges. Install new ones, if necessary.
The image transfer roller
need cleaning.
If toner smudges are on the front and
back of the page:
„ Open the printer front cover once
and close it again to clean the image
transfer roller.
There are
dark spots
on the
image.
The fuser oil roller is dirty
or worn.
Remove the fuser oil roller and check
the roller surface. If it is very dirty,
replace it.
The transfer belt is
defective.
Remove the transfer belt and check for
damage. If necessary, replace it.
Solving Problems with Printing Quality
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
79
Symptom
Cause
Solution
There are
toner
smudges
on the
back side
of the
page
(whether
or not it
has been
duplexed).
The paper transport rollers may be dirty.
Clean the paper transport, pressure,
and fuser oil rollers.
Image
defects in
same
place on
every
page.
Check the transport roller. If necessary,
replace it.
The media path is dirty
with toner.
Print several blank sheets and the
excess toner should disappear.
The fuser oil roller is dirty
or worn.
Remove the fuser oil roller and check
the roller surface for dirt or worn places.
If necessary, replace the fuser oil roller.
One or more of the toner
cartridges is defective.
Remove the toner cartridge and check
for damage. If necessary, replace it.
The OPC drum cartridge is
defective.
Remove the OPC drum cartridge and
check for damage. If necessary, replace
the entire drum kit.
The fuser unit is defective.
Replace the fuser unit.
The transfer belt is
defective.
Remove the transfer belt and check for
damage. If necessary, replace it.
ABCDE
ABCDE
ABCDE
ABCDE
80
Solving Problems with Printing Quality
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
Symptom
Cause
Solution
Abnormal
areas
(white or
black)
appear in
a regular
pattern.
Width of abnormal area:
1.25" (31.75 mm)
The toner cartridge is
damaged.
Remove the toner cartridge with the
color causing the abnormal image.
Replace it with a new toner cartridge.
Width of abnormal area:
3" (76.2 mm)
The transfer belt is
damaged.
Replace the transfer belt.
ABCDE
ABCDE
ABCDE
ABCDE
Width of abnormal area:
3.25" (82.55 mm)
The OPC drum cartridge is
damaged.
Replace the entire drum kit.
Width of abnormal area:
8" (203.2 mm)
The transfer belt is
damaged.
Replace the transfer belt.
Lateral image defects
have 1–2 mm spacing.
The laser lens cover is
dirty.
Clean the laser lens cover.
Lateral image defects
have 35 mm spacing.
The toner cartridge is
damaged
Remove the toner cartridge with the
color causing the abnormal image.
Replace it with a new toner cartridge.
Lateral image defects
have 75 mm spacing.
The image transfer roller is
damaged.
Replace the image transfer roller.
Lateral image defects
have 95 mm spacing.
The OPC drum cartridge is
damaged.
Replace the entire OPC drum kit.
Lateral image defects
have 204 mm spacing.
The fusing unit is
damaged
Replace the fusing unit.
Lateral image defects
have other spacing.
The OPC drum cartridge is
damaged
Replace the entire OPC drum kit.
Image
defects
cyclical
(evenly
spaced).
Solving Problems with Printing Quality
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
81
Symptom
Cause
Solution
Abnormal
areas
(white or
black belt
or spots)
appear.
One or more of the toner
cartridges is defective.
Remove the toner cartridge and check
for damage. If necessary, replace it.
The OPC drum cartridge
may be defective or
scratched.
Remove the OPC drum cartridge and
check the photosensitive surface (the
green surface) for scratches. If necessary, replace the entire drum kit.
The fuser oil roller is dirty
Remove the fuser oil roller and check
the roller surface for dirt or scratches. If
necessary, replace the fuser oil roller.
ABCDE or worn.
ABCDE
ABCDE
ABCDE The fuser belt may be
Clean the fuser belt.
dirty.
Lateral
lines or
bands
appear on
image.
82
The fusing unit may be
defective.
Replace the fusing unit.
The printer is not on a
level enough surface.
Level the printer (not exceeding 1.5°
slant).
The media path is dirty
with toner.
Print several sheets and the excess
toner should disappear.
One or more of the toner
cartridges is defective.
Remove the toner cartridge and check
for damage. If necessary, replace it.
The fuser oil roller is dirty
or worn.
Remove the fuser oil roller and check
the roller surface for dirt or worn places.
If necessary, replace the fuser oil roller.
The OPC drum surface is
scratched or damaged.
Remove the OPC drum cartridge and
check the green
photosensitive surface for scratches. If
necessary, replace the entire drum kit.
The transfer belt is misinstalled or defective.
Remove the transfer belt and reinstall it.
If necessary, replace it.
Solving Problems with Printing Quality
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
Symptom
Cause
Solution
Lateral
lines
appear
cyclically
(evenly
spaced)
on image.
Lateral lines have 1–2 mm
spacing.
Replace the laser lens cover.
Lateral lines have 35 mm
spacing.
Replace the color toner cartridge.
Lateral lines have 75 mm
spacing.
Replace the image transfer roller.
Lateral lines have 95 mm
spacing.
Replace the entire OPC drum kit.
Lateral lines have 204 mm
spacing.
Replace the fusing unit
Trailing edge 35 mm, other
spacing
Replace the entire OPC drum kit.
The laser lens cover may
be dirty.
Check to see if the laser lens cover is
dirty. If necessary, clean it with a clean
soft cloth.
One or more toner cartridges may be defective.
The item may be defective or misinstalled. Remove the designate item,
check it for damage and reinstall it. If
necessary, replace the entire drum kit.
Vertical
streaking
appears.
The OPC drum may be
defective or misinstalled.
The fuser unit may be
defective or misinstalled.
The transfer unit may be
defective or misinstalled.
The
image is
offset.
If a wide vertical white
band appears, check the
transfer belt surface.
Clean the transfer belt surface. If necessary, replace it.
The OPC drum cartridge is
defective.
Check the OPC drum cartridge. If necessary, replace the entire drum kit.
The fuser oil roller is
defective.
Check the fuser oil roller. If necessary,
replace it.
Make sure that the transfer unit is
closed.
ABCDE The fuser unit is defective. Check the fuser unit. If necessary,
ABCDE
replace it.
ABCDE
ABCDE
Solving Problems with Printing Quality
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
83
Symptom
Cause
Solution
Colors
look drastically
wrong.
One or more of the toner
cartridges are incorrectly
installed.
Remove the toner cartridges and reinstall them.
Colors are
not registering
properly;
colors are
mixed or
have
page-topage variation.
The front cover may not be
properly closed.
Make sure that the printer’s front cover
is closed.
The OPC drum
cartridge is not correctly
seated.
Remove the OPC drum cartridge and
reinstall it.
The toner in the cartridges
may need to be redistributed.
Remove the toner cartridges and gently
rock them five or six times to redistribute the toner. Then, reinstall the
cartridges.
One or more of the toner
cartridges is defective.
Remove the toner cartridge and check
for damage. If necessary, replace it.
ABCDE
ABCDE The media is moist from
ABCDE humidity.
ABCDE The transfer roller is
misinstalled.
The color
has a poor
reproduction or has
poor color
density.
ABCDE
ABCDE
ABCDE
ABCDE
84
Remove the moist media and replace it
with new, dry media.
Confirm the proper installation of the
transfer roller.
Agfa Screening is not
enabled.
Make sure you have Agfa Screening
enabld either in the control panel or in
the driver (Administration/Emulations/
PostScript/Halftone Type).
The paper image transfer
is defective.
Check the OPC drum cartridge. If necessary, replace the entire drum kit.
The Auto-Image Density
Control (AIDC) detection
sensor is dirty.
Open the front cover. Lift up the transfer
belt release lever to the 12 o’clock position. Next, return the lever to the 3
o’clock position. Repeat this operation
several times. (This cleans the surface
of the AIDC detection [image darkness]
sensor.)
Solving Problems with Printing Quality
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
Status, Error, and Service Messages
Status, error, and service messages are displayed in the control panel message window. They provide information about your printer and help you locate
many problems. When the condition associated with a displayed message
has changed, the message is cleared from the window.
Status and Error Messages
5"
Status messages are not displayed while the printer is off line.
This message...
means...
Do this...
<X> ACTIVE
JOBS
The printer is on line and
actively processing jobs. (<X>
identifies the number of jobs in
process.)
No action needed.
<X> COVER
OPEN
The <X> (specified cover) is
open and must be closed.
Close the cover.
<X> LIFE LOW
The <X> (specified item) is
near end of life, such as the
fuser oil roller. If you have a
new fuser oil roller on hand,
you may want to install it now.
If you don’t, order one now. A
limited number of copies
(about 100) will still print. However, when the oil runs out, the
printer stops and the FUSER
OIL EMPTY message
appears.
Replace the specified item.
<x> MISSING
The <X> (specified item) is
missing, such as the OPC
drum or toner.
Install a new item.
<X> TONER
EMPTY
The <X> (color) toner cartridge
is empty.
Replace the toner
cartridge.
Status, Error, and Service Messages
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
85
This message...
means...
Do this...
<X> TONER LOW
The <X> (color) toner cartridge
is low. There is still enough for
approximately 100 letter/A4
pages (at 5% coverage) before
the printer stops.
Redistribute the
toner in the cartridge, or replace
the cartridge.
ACC ALREADY
DISABLED
The accounting option
selected is now in effect.
No action needed.
The Job Accounting File is 80,
85, 90, or 95% full.
If you want
accounting
enabled, copy the
job accounting and
paper accounting
files to floppy
disk(s), or transfer
them to your host
computer using ftp
(if available). Then
reset the accounting files so that
new jobs can be
accepted. If you
don’t want to use
accounting, you
can disable it.
The accounting option is
disabled and the accounting
files are empty. After a reset,
the files are removed. This
prevents you from wasting disk
space with empty accounting
files.
No action needed.
ACC ALREADY
ENABLED
ACC DISABLED
ACC ENABLED
ACC FILE 95%
FULL
ACC FILE 90%
FULL
ACC FILE 85%
FULL
ACC FILE 80%
FULL
ACC FILES GOT
REMOVED
86
Status, Error, and Service Messages
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
This message...
means...
Do this...
ACC FILES NOT
EMPTY SHRUNK
TO %D
An attempt to reduce the size
Reset the accountof the accounting files has
ing files.
been made unsuccessfully
because the size of files is
bigger than the space required.
ACC_GETSTATUS
REC;CODE-%D,
RESETTING ACC
TO INITIAL
STATE
The accounting files have been
reset.
No action needed.
ADJUST
<INPUT> BIN
The<INPUT> (specified tray) is
not inserted correctly.
Adjust the tray.
CALIBRATING
PRINT QUALITY
After 100 1-sided pages of a
continuous print run, the
magicolor 2210 automatically
pauses to do an Auto-Image
Density Control (AIDC) cycle.
This process is provided to
make sure reliable printer
operation with optimum
output quality.
Wait. No action
needed.
CANCEL ALL
JOBS
The Cancel key has been
pressed, and one or more of
the print jobs in the print queue
are being canceled.
Press Select for all
jobs with a printing, interpreting,
spooled, or terminating status to be
completely
removed from the
system.
CANCEL JOB
The Cancel key has been
pressed, and the print job
in the print queue is being
canceled.
Press Select and
the job in the print
queue will be
canceled.
CHECK WASTE
TONER
Either the waste toner is full
and needs to be replaced, or it
is incorrectly installed.
Make sure that the
waste toner is not
full and is correctly installed.
Status, Error, and Service Messages
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
87
88
This message...
means...
Do this...
CREATED FILE
The accounting file has been
created.
No action needed.
CREATING
XXXXXXXXXXXX
FILE, WAIT...
The specified accounting file is
created when accounting is
enabled and the files are not in
existence or these files are
created following a Reset
Accounting (XXXXXXXXXXXX
represents the Job Accounting
or Paper Accounting file).
Wait. No other
action needed.
DSK TOO SMALL
ACC NOT
ENABLED
There is not enough space in
the hard disk to create the
accounting file.
Remove unnecessary files stored in
the hard disk.
END JOB
The Cancel key has been
pressed and the End Job
option selected.
Press Select to
provide an
end-of-job indicator for a print job
that does not
have one.
ENERGY SAVER
The printer is in energy saver
mode to reduce power consumption during periods of
inactivity. When a print job is
received, the printer returns to
normal power within 90 seconds. While in “deep sleep,”
the printer’s message window
will not display operator status
such as door- and tray-open
messages. The printer remains
in “deep sleep,” until a print job
is received, or until the printer
is manually switched from
offline to online.
No action needed.
EXTENDED ACC
FILE SIZE BY
<X> KB
The <X> (size of the nonempty accounting file) has
been increased successfully.
No action needed.
Status, Error, and Service Messages
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
This message...
means...
Do this...
FUSER OIL
EMPTY
The fuser oil roller for the fuser
is depleted. The printer will not
print any more copies until a
new fuser oil roller is installed.
Install a new fuser
oil roller.
IDLE
The printer is on line, but no
jobs are in process.
No action needed.
INITIALIZING
The printer is warming up and
getting ready to go on line.
Wait. No other
action needed.
INPUT BIN JAM
Input bin jams occur in the
input bin.
Locate and
remove the jam.
INPUT IDLE
PRINTING
The printer is on line and printing jobs already in the queue.
No new jobs are arriving at the
communication interfaces.
No action needed.
MAILBIN POWER
OFF
The mailbox unit power is off.
Turn off the printer,
turn on the mailbox unit, then the
turn on the printer.
Status, Error, and Service Messages
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
89
This message...
means...
Do this...
MAIN UNIT
COVER OPEN
The front, top, or duplex covers
are open and must be closed.
Close the specified
cover(s).
MEDIA JAM
DUPLEX
Media has jammed in the
duplex area or duplex refeed
area on the models with duplex
units installed.
Locate and
remove the jam.
MEDIA JAM
EXIT
Media has jammed between
the print engine and the output
tray.
A media jam has been
detected between the fuser
and output tray rollers located
near the top cover.
Exit jams occur in the media
eject area.
90
MEDIA JAM
FUSER
Media has jammed leaving the
fuser area.
MEDIA JAM
MAIL BIN
Mail bin jams occur if the
media is jammed in the 5-bin
mailbox on the models with the
5-bin mailbox installed,
between the printer and the
5-bin mailbox, in the mailbox
eject area, or in the mailbox
transport area.
MEDIA JAM MPT
Media has jammed while being
pulled from the specified multipurpose tray.
Status, Error, and Service Messages
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
This message...
means...
Do this...
MEDIA JAM
OPTIONAL TRAY
Tray jams occur between the
standard upper or optional tray
and the print engine. A misfeed
jam may be as simple as a
sheet of media not being
picked, or it may be that the
media was picked but not fed
properly.
Locate and
remove the jam.
The lower feeder unit (optional)
door is open.
Close the door.
MEDIA JAM
TRANSFER
Transfer jams occur in the
transfer roller area. This type
of jam means that the media
did not make it to the paper
exit area.
Locate and
remove the jam.
MEDIA JAM
UPPER TRAY
Media has jammed while being
pulled from the specified tray.
MEDIA SIZE
MISMATCH
The media detected in the tray
doesn’t match the media size
setting.
Change the media
in the tray or
change the media
size setting.
NEW FILE SIZE
IN EFFECT
The size of the accounting files
has been increased or
decreased.
Press Select to
accept changes.
NO PRNTREQ
ERROR
A printer hardware error has
occurred.
Reboot printer. If
message continues to appear,
contact your service provider or
Support. See the
Service & Suuport
Guide for support
telephone numbers.
ONLINE
The printer is online and ready
to print.
No action needed.
Status, Error, and Service Messages
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
91
92
This message...
means...
Do this...
OUTPUT BIN
FULL
The media has exceeded the
limit in the specified output bin.
Remove the media
from the specified
output bin.
PAPER MISMATCH
The media detected in the tray
doesn’t match the media size
setting.
Change the media
in the tray or
change the media
size setting.
PRINTING STATUS
A status page is printing
Wait until after the
status page prints,
and the message
clears.
PUT <X> IN
INPUT <Y>
The <X> specified media is not
in the input tray <Y>.
Refill the tray with
the specified type
media.
PUT <SIZE>
PAPER IN
<BIN>
The Operator Control/Chain
Inputbins is set to Off and the
displayed tray is empty. Refill it
with the specified size media.
<SIZE> is the media size
detected by the engine, and
<BIN> is the empty tray.
Refill the tray with
the specified size
media.
PUT <TYPE
MEDIA> IN
INPUT BIN
Operator Control/Chain Inputbins is set to On and a chained
tray is empty.
Refill the tray with
the specified type
media.
REPLACE <X>
The specified item <X> needs
to be replaced, such as the
OPC drum.
Replace the specified item.
RESETTING
ACCOUNTING
The reset accounting operation
is in process.
No action needed.
WAITING FOR
IDLE
An active job is in process.
Wait until the print
Access to the menu is not
job is finished and
allowed until the job is finished. the printer goes
idle.
Status, Error, and Service Messages
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
This message...
means...
Do this...
WAITING ON
INPUT
END JOB?
The compiler is waiting on
incoming data for the first job in
the queue. The job may not
have an end-of-job indicator
and therefore cannot end. The
message clears if more input
arrives from the port or if you
press the Cancel key. No other
jobs can be printed until this
job has ended.
Wait until the job is
finished and the
printer goes idle to
access the configuration menu.
WARMING UP
The printer is warming up.
Wait. No other
action needed.
WASTE TONER
NEAR FULL
The waste toner pack is nearly
filled with toner.
Replace the waste
toner pack.
WASTE TONER
FULL
The waste toner pack is filled
with toner.
Replace the waste
toner pack.
Status, Error, and Service Messages
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
93
Service Messages
This service
message...
SERVICE CALL 04
MAIN UNIT
Means...
An error has been detected with the item
indicated in the service message.
Correction of these errors is performed
by a MINOLTA-QMS authorized service
provider only. Contact your local vendor.
A service message sometimes occurs as a
result of an unusual combination of events,
not because of an actual problem. When
the printer stops and a service message
displays in the message window, turn the
printer off and then back on. This often
clears the service message indicator, and
printer operation resumes. Always try this
before making a service call.
Service calls should be placed to the
vendor from whom you purchased the
printer. If you cannot get service from
your vendor, see the Service & Support
Guide for additional contact information.
94
Status, Error, and Service Messages
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
This service
message...
SERVICE CALL 05
FLASH ROM
SERVICE CALL 08
MAIN MOTOR
SERVICE CALL 09
FUSING MOTOR
SERVICE CALL 0B
XFER FAN BELT
SERVICE CALL 0C PWR
SUPPLY FAN
SERVICE CALL 0D
ENGINE FAN
SERVICE CALL OE
SUCTION FAN
SERVICE CALL OF
FUSING UNIT FAN
Means...
An error has been detected with the item
indicated in the service message. Correction of these errors is performed by a
MINOLTA-QMS authorized service provider only. Contact your local vendor.
A service message sometimes occurs as a
result of an unusual combination of events,
not because of an actual problem. When
the printer stops and a service message
displays in the message window, turn the
printer off and then back on. This often
clears the service message indicator, and
printer operation resumes. Always try this
before making a service call.
Service calls should be placed to the vendor from whom you purchased the printer.
If you cannot get service from your vendor,
see the Service & Support Guide for additional contact information.
SERVICE CALL 10
POLYGON MOTOR
SERVICE CALL 12
LASER ERROR
SERVICE CALL 14
XFER ROLLER
SERVICE CALL 15
XFER BELT CLN
SERVICE CALL 16
XFER BELT ROT
SERVICE CALL 17
TONER RACK
SERVICE CALL 1A FUS
UPP HIGHTMP
SERVICE CALL 1B FUS
UPP THERM
Status, Error, and Service Messages
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
95
This service
message...
Means...
SERVICE CALL 1C FUS
LOW WARMUP
SERVICE CALL 1D FUS
LOW LOWTMP
SERVICE CALL 1E FUS
LOW HIGTMP
SERVICE CALL 18 FUS
UPP WARMUP
SERVICE CALL 19 FUS
UPP LOWTMP
SERVICE CALL 1F FUS
LOW THERM
SERVICE CALL 20 FUS
RETRACT
SERVICE CALL 21
TRANS DET SENS
An error has been detected with the item
indicated in the service message. Correction of these errors is performed by a
MINOLTA-QMS authorized service provider only. Contact your local vendor.
A service message sometimes occurs as a
result of an unusual combination of events,
not because of an actual problem. When
the printer stops and a service message
displays in the message window, turn the
printer off and then back on. This often
clears the service message indicator, and
printer operation resumes. Always try this
before making a service call.
Service calls should be placed to the vendor from whom you purchased the printer.
If you cannot get service from your vendor,
see the Service & Support Guide for additional contact information.
SERVICE CALL 22 MAN
TRAY LIFT
SERVICE CALL 29 MEM
MALF COUNTER
SERVICE CALL 2A MEM
MALF DATA
SERVICE CALL 2B MEM
MALF ACCESS
SERVICE CALL 2C MEM
MALF INSTALL
SERVICE CALL 30
5BIN MAIL
SERVICE CALL 31
5BIN INST MAIL
96
Status, Error, and Service Messages
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
HP-GL, HPXL, and PCL Error Codes
The following tables list error codes that could appear on the printer message
window when running the HP-GL, HPXL, or PCL emulation.
HP-GL
PCL
Error Description
Error Description
Code
Code
0
Not enough memory for job.
0
Not enough memory for
job.
1
Too many transformations.
1
State lost.
2
Math error.
2
Math error.
3
Job aborted.
3
Job aborted.
4
Instruction not recognized.
4
Out of memory for
macros.
5
Wrong number of parameters.
5
Disk full. Cannot store
fonts.
6
Out of range parameter, or
illegal character.
6–13
Internal error 1–8.
7
Not used.
8
Unknown character set.
9
Position overflow.
10
Buffer overflow.
11
Not used.
HPXL
Error
Description
Code
0
Not enough memory for
job.
1
Math error.
2–7
Internal error 1–6
Status, Error, and Service Messages
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
97
PostScript Errors
If your printer is having trouble printing when using PostScript emulation, you
should turn on the Error Handler in the control panel menu. Error Handler is a
diagnostic tool that identifies PostScript errors encountered during a print job.
Menu
Administration/Startup Options/Do Error Handler
Choices
Yes—Load the Error Handler on reboot.
No—Don’t load the Error Handler on reboot.
Default
No
Notes
Refer to the PostScript Language Reference Manual (Adobe
Systems Incorporated, Reading, PA: Addison-Wesley, 1990,
ISBN 0-201-18127-4) for information on PostScript errors.
You must reboot the printer after turning on the error handler.
Additional Assistance
If you’ve followed all of the instructions in this guide and still have problems
you can’t solve, refer to the Service & Support Guide or visit our web site at
www.minolta-qms.com for current information on getting help.
98
Additional Assistance
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
Installing Other
Accessories
5
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
Introduction
This chapter provides information about the following accessories. Contact
your local vendor for purchase information.
5-bin Mailbox
Three models: For 100-, 120-, or 220-volt printers
Automatic Document ADF for convenience copier
Feeder (ADF) for
SC-210/110
BuzzBox
Via parallel connection for 100, 120, and 220 volts
Dual In-Line Memory 32, 64, or 128 MB, PC-100 Compliant SDRAM
Modules (DIMMs)
DIMMs, up to a printer maximum of 384 MB
Duplex Unit
Automatic duplexing
Emulations,
Fonts, Utilities, and
Other Software
„ ImageServer
„ TIFF
„ CALS
„ LNO3
„ CGM
„ Kanji Font Internal IDE Hard Disk
„ QFORM
„ PlanetPress (forms-creation utility)
„ Fonts
Interfaces and
Daughterboards
„ Crown for DECnet-TCP/IP (equipped with
10BaseT)
„ CrownNet for Ethernet 10BaseT/100BaseTX
(equipped with RJ45 connector)
„ CrownNet for Token-Ring (equipped with STP
and UTP connectors)
„ SCSI Interface
Internal IDE Hard
Disk Drive
Used for storage of fonts, forms, and overlays; virtual
memory; and job spooling
Lower Feeder Unit
(LFU)
Media tray included
Media Tray, 500
Sheet
Purchasing extra trays may be convenient when
changing media formats and/or media qualities vary.
Printer Stand and/or Various models available
Cabinet
100
Introduction
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
SC-210
Convenience copier with optional automatic
documnet feeder
Time-of-Day Clock
Time stamps jobs in accounting files, and header
and trailer pages
Accessories
Attention
Installing accessories always requires that the printer and accessories
are turned off and unplugged during installation.
Antistatic Protection
Attention
It’s very important to protect the printer controller board and any
associated daughterboard or module from electrostatic damage while
performing any task involving the controller board.
If an antistatic wrist strap is provided in your printer option kit, attach
one end of it to your wrist and the other end to any convenient electrical
ground (for example, the bare metal chassis of equipment, as on the
back of a computer, that is plugged in but turned off). Never attach the
wrist strap to any piece of equipment with an electrical current present.
Turn off all power switches first. Plastic, rubber, wood, painted metal
surfaces, and telephones are not acceptable grounding points. The
printer isn’t an acceptable grounding point either because it must be
unplugged before you perform this task. If you don’t have an antistatic
wrist strap, discharge your body’s static electric charge by touching a
grounded surface before you handle any printer boards or components
and before removing the controller board. Also avoid walking around
after grounding yourself.
BuzzBox
BuzzBox is a printer accessory that warns you with a buzzer and/or a blinking
light any time the printer goes off line. This means you’re alerted to print job
interruptions, such as empty media trays or other consumable issues.
Antistatic Protection
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
101
What's in the Kit?
The BuzzBox kit contains the following items:
„ BuzzBox
„ Interface box
„ RJ-11 cable
„ Power adapter
„ Adhesive-backed clips
Installing BuzzBox
1
2
If you have a cable attached to the printer’s parallel port, unplug it from
the printer.
Attach one end of the parallel cable on the interface box to the printer’s
parallel port.
5"
The BuzzBox’s ribbon cable is designed to be directly attached to
the printer’s parallel port, not to an adapter or an additional cable.
BuzzBox
Interface
Box
Adapter
Ribbon Cable
3
Use the included RJ-11 cable to connect BuzzBox to the interface box.
102
BuzzBox
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
4
Choose a good location on the printer to mount the interface box. Make
sure that the unit does not
z interfere with paper exiting the printer.
z cover any vents, doors, connectors, or labels.
z cause the BuzzBox ribbon cable to stretch or twist.
5
Use the adhesive-backed clips provided to mount the BuzzBox where the
printer operator can see and/or hear it.
A 14-foot (4.2 m) cable is provided, but you can use up to a 500-foot cable
(RJ-11 4-pin or 6-pin).
6
Connect the interface box to an electrical outlet.
A 110/220-volt adaptor is provided in the US, and a universal power
supply is provided outside the US.
7
8
If you unplugged a parallel cable from the printer in step 1, attach the
cable to the parallel port on the interface box.
To test the BuzzBox, make sure its switches are on, then press the
printer’s Online key to take the printer off line.
5"
You can use the BuzzBox switches to enable or disable the
buzzer, the light, or both.
When the printer goes off line, the light flashes and the buzzer sounds
until the printer is placed back on line or until the light and buzzer switches
are turned off.
Using BuzzBox
„ When the BuzzBox lights or buzzes, check the printer message window to
find out what has interrupted printing. See “Status, Error, and Service
Messages” on page 85 for a list of printer messages and how to respond
to them.
Remember that pressing the Online key to enter the printer configuration
menu triggers the BuzzBox alarm.
Dual In-Line Memory Modules
Dual in-line memory modules (or DIMMs) are compact circuit boards with
surface-mount memory chips.
Your magicolor 2210 printer comes with 128 MB SDRAM of printer memory.
However, you can upgrade to a maximum of 384 MB of RAM through the
installation of additional DIMMs. Additional memory must be 32, 64, or
128 MB, PC-100 Compliant SDRAM DIMMs.
Dual In-Line Memory Modules
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
103
Additional memory allows you to download more fonts and increase the
printer's buffer (area where data sent from the computer is stored while
waiting to be printed).
5"
You will also need additional memory to duplex print at 1200 x 1200
dpi on letter and legal media sizes.
How Much Memory Do You Need?
The amount of RAM installed in your printer governs which resolutions can be
used with each media size.
If a certain resolution is chosen and the minimum amount of memory is not
installed in the printer, the file is printed using the next lower resolution that
can handle the job. For example, if you attempt to print a 4-color duplex
image at 1200x1200 dpi resolution on legal media, but the printer has only
128 MB of RAM instead of the required 256 MB minimum, the file prints at
600x600 dpi.
The magicolor 2210 will print all print jobs at the highest resolution that the
installed memory will support.
Minimum System Memory Requirements (in MB)
Media
Size
600x600
1200x1200
Mono Mono 4-Color 4-Color Mono Mono 4-Color 4-Color
Duplex
Duplex
Duplex
Duplex
Letter, A4
Basic*
128
128
128
128
128
128
128
192
Maximum
Performance*
128
128
128
128
128
128
192
256
Basic*
128
128
128
128
128
128
128
256
Maximum
Performance*
128
128
128
128
128
128
256
384
Legal
* “Basic” memory requirement is the minimum memory required to print at the indicated
resolution.
“Maximum Performance” memory requirement is the minimum memory required to
achieve the maximum performance possible for any given job. The page rate, with maximum listed memory, will be determined solely by the complexity of the job.
You may also need additional memory (DIMMs) for the following:
104
Dual In-Line Memory Modules
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
„ To print complex graphics or complex PostScript documents
„ For increased collation performance
„ For increased spooling performance
The magicolor 2210 has 3 DIMM slots available. The maximum memory
that can be installed is 384 MB (3 x 128 MB DIMMs).
Standard Memory
Supports up to...
128 MB SDRAM DIMM 4-color 1200x1200 dpi simplex printing, at
basic performance, on all paper sizes up to
and including 8.5" x 14" (215 mm x 356 mm)
„ Check the startup page to make sure the printer has enough RAM
installed.
„ If you have enough RAM installed, and you have configured the printer
from the control panel to print at 600x600 or 1200x1200 dpi resolution
(Administration/Engine/Def Resolution menu) but the printer continues
printing at a lower resolution, you may need additional memory allocated
to the frame buffer. (See the CrownBook for instructions.)
To allocate the default amount of memory to the memory clients, use the
Administration/Memory/Quick Config menu to choose the correct
resolution and paper size for your printing.
If you experience a problem with your magicolor 2210, first go through the
installation procedure in this guide once more. Verify each item thoroughly.
You may also refer to the User’s Guide for troubleshooting tips. If you still
experience a problem, contact your local vendor or contact Customer
Service.
Installation
Attention
It’s very important to protect the printer controller board and any
associated circuit boards from electrostatic damage. Before
performing this procedure, review the antistatic caution on page
105. In addition, always handle circuit boards by the edges only.
1
If you are not to the point when you are able to print an advanced status
page yet, skip to step 2.
If you have previously installed your printer and have confirmed that it is
printing, print an advanced status page in case you need to restore any
memory settings after the DIMM installation.
Dual In-Line Memory Modules
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
105
Installing DIMMs automatically restores memory defaults. If your memory
settings are specific to your environment, print an advanced status page
before installing DIMMs, so you can recover the current memory settings.
2
3
Ensure that the printer is turned off and the power cord and all interface
cables are disconnected.
Remove the printer’s controller board.
Loosen five screws and, using the tab on the lower side of the connector
panel, pull the controller board from the printer.
4
5
Position the controller board on a flat surface so the controller board lies
flat and the I/O connector panel is facing you.
If you need to remove a
DIMM before installing
one, remove it as
follows; otherwise skip
to step 6.
5"
If all the DIMM
connectors are
filled and you
want to install
more memory,
you have to
exchange one or
more DIMMs for
DIMMs with a
greater memory
capacity.
IIIIII
IIIIII
IIIIII
IIIIII
IIIIII
IIIIII
IIIIII
IIIII
IIIIII
.. ..
IIIIII
.. .. .. .. .. .. .. ..
IIIIII
IIIIII
.. .. .. .. .. ..
IIIIII
.. .. .. .. .. ..
IIIII
.. ..
.. .. .. .. .. ..
.. .. .. .. .. ..
.. .. .. .. .. .. .. ..
IIIIII
.. .. .. .. .. ..
.. .. .. .. .. ..
III
.. .. .. .. ..
.. .. .. .. .. ..
.. .. ..
.. .. ..
.. .. .. .. .. ..
.. ..
.. .. .. .. .. ..
.. .. .. .. .. ..
.. .. .. .. .. .. .. ..
.. .. .. .. .. ..
.. .. .. .. .. ..
..
.. .. .. .. .. ..
.. .. .. .. ..
.. .. .. .. ..
.. .. .. .. ..
.. .. ..
.. .. .. .. .. ..
.. .. ..
..
.. .. .. .. .. ..
..
..
.. ..
.. .. .. .. .. .. ..
.. .. .. .. .. ..
.. .. .. .. .. ..
.. .. .. .. .. ..
.. .. .. .. .. ..
..
..
..
.. .. ..
..
.. .. .. ..
.. ..
.. ..
.. ..
.. .. .. .. .. .. ..
.. .. .. .. .. ..
.. .. .. .. .. ..
.. ..
.. .. .. .. .. ..
.. .. ..
.. ..
.. .. .. .. .. ..
.. ..
... ...
IIII
... ... ... ... ... IIIIIIIIIIII
... ...
...
IIII
... ...
... ... ... ... ... IIIIIIII
... ... ... ... ...
IIII
... ...
...
... ...
...
... ... ... ... ... IIIIIIIIIIII
... ... ... ... ...
... ...
...
... ...
... ... ... ... III IIII
...
... ... ... ... ...
... ...
... ... IIIIIIII
... ...
...
... ... ... ...
... ... ... ... ... IIIIIIIIIIII
... ...
... ...
IIII
...
... ...
... ... ... ... IIIIIII
... ...
... ... ... ... ...
... ... IIIIIIII
... ...
...
I
... ... ... .
... ... ... ...
... .
... ...
... ...
... ... ... .
... .
a Using both thumbs, pull the latches (one on each side of the DIMM
connector) outward.
b Lift the DIMM straight out of the DIMM connector.
3
106
Insert the new DIMM straight down into the DIMM connector until the
latches snap into the locked position.
Dual In-Line Memory Modules
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
Observe the keyed
side of the DIMM to
align it with the
connector. When
seated, the DIMM
stands upright, firmly in
place. If you cannot
snap the DIMM into
place, do not force it.
Reposition it, making
sure that the bottom of
the DIMM is seated
completely in the
connector.
4
5
IIIIII
IIIIII
IIIIII
IIIIII
IIIIII
IIIIII
IIIIII
IIIII
.. ..
IIIIII
IIIIII
.. .. .. .. .. .. .. ..
IIIIII
.. .. .. .. .. ..
IIIIII
.. .. .. .. .. ..
IIIIII
.. ..
.. .. .. .. .. ..
IIIII
.. .. .. .. .. .. .. ..
.. .. .. .. .. ..
IIIIII
.. .. .. .. .. ..
.. .. .. .. .. ..
III
.. .. .. .. .. ..
.. .. .. .. ..
.. .. ..
.. .. .. .. .. ..
.. .. ..
.. ..
.. .. .. .. .. .. ..
.. .. .. .. .. ..
.. .. .. .. .. ..
.. .. .. .. .. ..
.. .. .. .. .. .. .. ..
.. .. .. .. .. ..
.. .. .. .. ..
.. .. .. .. .. ..
.. .. .. .. .. ..
.. .. ..
..
..
..
..
.. ..
.. .. ..
.. .. .. .. .. ..
.. .. ..
..
.. .. .. .. .. ..
.. .. .. .. .. .. .. ..
..
.. .. .. .. ..
.. .. .. .. .. ..
.. .. .. ..
.. .. .. .. ..
.. .. ..
.. ..
.. ..
.. .. ..
.. ..
.. .. .. .. .. .. .. ..
.. .. .. .. .. ..
.. .. .. .. .. ..
.. ..
.. .. .. .. ..
.. .. ..
.. ..
.. .. .. .. .. ..
.. ..
... ...
III
... ... ... ... ... IIIIIIIIIIII
... ...
III
...
... ...
... ... ... ... ... IIIIIIIII
... ... ... ... ...
III
... ...
...
... ...
...
... ... ... ... ... IIIIIIIIIIII
... ... ... ... ...
... ...
III
...
... ...
... ... ... ... II III
...
... ... ... ... ...
... ...
... ... IIIIIIIII
... ...
...
... ... ... ...
... ... ... ... ... IIIIIIIIIIII
... ...
... ...
III
...
... ...
... ... ... ... IIIIIIII
... ...
... ... ... ... ...
... ... IIIIII
... ...
...
... ... ... . III
... ... ... ...
... .
... ...
... ...
... ... ... .
... .
Repeat steps 5–6 for
each additional DIMM
that you install.
Reinstall the controller board into the printer.
Gently slide the controller board into the printer until it is fully seated, and
then tighten the five screws.
When you print a startup page, verify that the total size of the RAM
installed in your printer is listed.
Installing a Duplex Unit
Read this section if you purchased a duplex unit for your magicolor 2210.
Kit Contents
„
Duplex unit
„
2 thumbscrews
Installation
1
Remove the duplex unit from its shipping box.
Installing a Duplex Unit
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
107
2
3
4
Remove the tape from the
unit.
Open the multipurpose tray.
Remove the two thumbscrews
from the right side cover.
5"
108
Retain these screws in
case you need to
remove the duplex unit
in the future.
Installing a Duplex Unit
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
5
6
7
8
9
Press the right-side cover release
button.
Open the right-side cover.
Pull the right-side cover
toward you, lift it, and unhook it
from its frame.
With the multipurpose tray still
open, close the right-side cover.
Insert the bottom of the duplex
unit at a shallow angle into the
right-side cover.
To do this, place the two tabs at
the bottom into the holes on the
right-side cover.
Installing a Duplex Unit
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
109
10
11
12
110
Press the top of the duplex unit in.
Open the duplex unit paper path
cover.
Secure the duplex unit tightly with
the two thumbscrews supplied in
the kit.
Installing a Duplex Unit
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
13
14
15
Close the duplex paper path cover and
multipurpose tray.
Open the right-side cover.
Extend the spring wire for the
duplex unit about 1 foot (30.5
cm).
Installing a Duplex Unit
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
111
16
17
Attach the end of the spring
wire to the hook on the printer
unit.
Close the right-side cover.
Emulations, Fonts, and Other Software
Emulations
Optional emulations, such as ImageServer, LN03, and CGM are available as
PostScript files. This section describes how to download an emulation to the
printer’s hard disk.
5"
You must have at least one hard disk, internal or external, attached to
the printer in order to use an optional emulation. If more than one hard
disk is available, the emulation automatically installs itself on the disk
with the most free storage space. MINOLTA-QMS recommends that
you have at least 4 MB of memory above the base configuration and
that you add at least 1 MB memory to each emulation installed. This
ensures that the printer can run the emulation without slowing down
performance.
Downloading an Emulation via a Parallel Interface
1
2
3
Turn on the printer, and wait for IDLE to display in the message window.
Insert the emulation CD-ROM or disk in your PC, and change to that drive
(for example, if you’re using the D drive, type d:↵).
Send the emulation to the printer’s hard disk. Type
copy filename 1pt#↵
where filename is the name of the installation file and where # is 1 to 3.
4
When downloading is complete, reboot the printer.
The emulation should be listed in the Options section of the printer’s
startup page, in the Administration/Emulation printer’s configuration
menu, and on the advanced status page.
112
Emulations, Fonts, and Other Software
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
Downloading an Emulation via an Ethernet Interface
5"
1
2
3
Before you begin this procedure, your printer and PC (or UNIX
workstation) must be connected to an Ethernet network running TCP/
IP and have valid IP addresses.
Turn on the printer, and wait for IDLE to display in the message window.
If your PC is running Windows, change to DOS.
Insert the emulation CD-ROM or disk in your PC, and change to that drive
(for example, if you’re using the D drive, type d:↵).
If you want to download the emulation from a UNIX workstation, copy the
installation file from the emulation CD-ROM or disk to a temporary
directory on your UNIX workstation, then change to that directory.
4
5
Open an ftp session at your PC or workstation by typing one of the
following commands:
ftp printername↵
(for example, ftp pctdev6↵)
ftp ipaddress↵
(for example, ftp 161.33.130.45↵)
When prompted for a user name and password, press Enter for both.
An ftp> prompt displays.
6
At the ftp> prompt, change to binary mode by typing
bin↵
7
At the ftp> prompt, send the emulation file to the printer’s hard disk by
typing
put filename↵
where filename is the name of the installation file.
The printer’s message window reads 1 ACTIVE JOB to indicate that the
emulation is being downloaded to the hard disk. The ftp> prompt returns
when the emulation has finished loading.
8
At the ftp> prompt, end the ftp session by typing
quit↵
9
10
When the Disk light stops flashing and the printer’s message window
reads IDLE for at least 30 seconds, turn the printer off and then on again.
When downloading is complete, reboot the printer.
The emulation should be listed in the Options section of the printer’s
startup page, in the Administration/Emulation printer’s configuration
menu, and on the advanced status page.
5"
You may want to erase any installation files left on your computer
(and/or workstation), and then remove any temporary directories.
Emulations, Fonts, and Other Software
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
113
Using an Optional Emulation
Refer to the documentation that came with your emulation for configuration
and usage instructions.
Fonts
Optional fonts are available as files on floppy disks or CD-ROMs. This section
describes how to download optional fonts from a floppy disk or CD-ROM to
the printer’s hard disk.
5"
At least one hard disk (internal or external) must be present on your
printer before you can download a font. If more than one hard disk is
available, the font automatically installs itself on the disk with the most
free storage space.
Downloading Disk Fonts via a Parallel Interface
1
2
3
Turn on the printer, and wait for IDLE to display in the message window.
Insert the font disk or CD-ROM in your PC, and change to that drive (for
example, if you’re using the A drive, type a:↵).
Send the fonts to the printer’s hard disk. Type
copy filenamelp+1↵
where filename is the name of the installation file
4
When the downloading is complete, reboot the printer.
Downloading Fonts via an Ethernet Interface
5"
1
2
3
4
114
Before you begin this procedure, your printer and PC (or UNIX
workstation) must be connected to an Ethernet network running TCP/
IP and have valid IP addresses.
If your PC is running Windows, change to DOS.
Insert the fonts disk or CD-ROM in your PC, and change to that drive (for
example, if you’re using the A drive, type a:↵).
If you want to download the fonts from a UNIX workstation, copy the
installation file from the fonts disk to a temporary directory on your UNIX
workstation.
Turn on the printer, and wait for IDLE to appear in the message window.
Emulations, Fonts, and Other Software
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
5
6
Open an ftp session at your PC or workstation by typing one of the
following commands:
ftp printername↵
(for example, ftp pctdev6↵)
ftp ipaddress↵
(for example, ftp 161.33.130.45↵)
When prompted for a user name and password, press Enter for both.
An ftp> prompt displays.
7
At the ftp> prompt, change to binary mode by typing
bin↵
8
At the ftp> prompt, send the fonts file to the printer’s hard disk by typing
put filename↵
where filename is the name of the installation file.
The printer’s message window reads 1 Active Job to indicate that the
fonts are being downloaded to the hard disk. The ftp> prompt returns
when the fonts have finished loading.
9
At the ftp> prompt, end the ftp session by typing
quit↵
10
11
When the Disk light stops flashing and the printer’s message window
reads IDLE for at least 30 seconds, turn the printer off and then on again.
When the printer’s message window reads IDLE again, the fonts are
ready to use.
The fonts should be listed in the Fonts section of the printer’s Advanced
Status page.
5"
You may want to erase any installation files left on your computer
(and/or workstation), and then remove any temporary directories.
Kanji Font Internal IDE Hard Disk
The preformatted Kanji font internal IDE hard disk contains Kanji fonts and
other files. These fonts can be printed at a variety of point sizes and in
different styles and resolutions.
After the Kanji hard disk is installed in your magicolor 2210, the Kanji fonts
are available for use just as if they were resident in the printer.
Kanji Font Internal IDE Hard Disk
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
115
What's in the Kit?
„ Internal hard disk preformatted with the following Kanji fonts:
z FutoGoB101-Bold
z FutoMinA101-Bold
z GothicBBB-Medium
z Jun101-Light
z MidashiGo-MB31
z MidashiMin-MA 31
z Ryumin-Light-KL
„ IDE hard disk with ribbon cable attached
„ IDE hard disk bracket
„ 4 screws
Hardware Requirements
„ A Macintosh, IBM PC, or compatible computer
Software Requirements
„ An application (such as a word processing or desktop publishing package) that supports the PostScript printing. If you’re using a Macintosh, the
following Macintosh system software:
z KanjiTalk, version J1-6.0.7 or later
z System File, version J1-6.0.7 or later
z Laser Prep, version J1-6.0.1 or later
z LaserWriter, version J1-6.0.2 or later
z Print Monitor, version J1-1.3 or later
z MultiFinder, version J1-6.1.7 or later
z Macintosh OS 8.xJ
„ If you’re using a PC, the following system software:
z If you’re using Windows, version 3.1J or later
z If you’re using DOS, version 5.0J or later
116
Kanji Font Internal IDE Hard Disk
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
Installing a Kanji Font Internal IDE Hard Disk
Attention
The Kanji fonts are factory installed on a formatted hard disk drive. DO
NOT reformat or initialize the Kanji internal hard disk. Reformatting
erases all data, fonts, and files on the disk. Your warranty does not
cover this error.
The Kanji font internal IDE hard disk is installed on the controller board in the
same way any internal hard disk is installed. See “Internal IDE Hard Disk
Drive” on page 127 for detailed steps on installing an internal hard disk.
Attention
If you already have an internal hard disk installed, you must remove it
before you can install the Kanji disk.
Configuring the Printer for Kanji
See “Storage Devices” in the CrownBook for information on how to configure
your printer’s memory when using an internal hard disk.
5-bin Mailbox
Read this section if you purchased a 5-bin mailbox for your magicolor 2210.
Kit Contents
„ Mailbox unit
„ 5 bins
„ 2 thumbscrews
„ Accessory
screen cover
„ Power cord
Installation
1
Remove the
mailbox unit
from its shipping
box.
5-bin Mailbox
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
117
2
3
4
5
118
Remove any tape and packing material.
Open the mailbox unit cover and
remove any packing material from the
rear of the mailbox unit.
Close the mailbox unit cover.
Remove any packing material from the
front of the mailbox unit.
5-bin Mailbox
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
6
Remove the two screen covers from the
top of the printer.
Pry the covers off with your fingers.
Retain these covers in case you ever
want to remove the 5-bin mailbox.
7
8
Locate the two holes, the pin, and the
positioning guide for the mailbox.
Slowly lower the mailbox unit so that the
two pins at the bottom fit into the two
holes in the printer and the pin on the
printer fits into the hole at the bottom of
the mailbox.
5"
9
The mailbox bins will face the left
side of the printer.
Push the mailbox toward the right-hand
side of the printer until it stops.
5-bin Mailbox
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
119
10
11
12
13
14
120
Secure the mailbox
tightly with the two
thumbscrews supplied in
the kit.
Place the slot on the right side of the
accessory screen cover from the kit onto
the tab on the mailbox then press on the
left side of the accessory screen cover so
the tab on that side fits into the slot on the
mailbox.
Remove the five plastic bins from their
packaging.
Hold a bin and insert the right
side into the bottom level of
the mailbox unit, then insert
the left side.
Install the other four bins.
5-bin Mailbox
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
15
16
Plug the mailbox power cord from the kit
into the mailbox unit (lower connection).
Plug the other end of the power cord into
the printer.
17
Make sure the printer is turned off.
18
Make sure the 5-bin mailbox is turned off.
Attention
Always turn off the printer before turning off the mailbox.
5-bin Mailbox
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
121
19
20
21
Plug the printer power
cord into the mailbox
unit (upper connection)
and into the dedicated,
grounded, surgeprotected electrical
outlet.
Turn the mailbox
unit on.
Turn the printer on.
QFORM
QFORM allows you to use existing lineprinter and forms-printing applications
on your magicolor 2210. This printer-resident application gives you the ability
to store PostScript forms on the printer’s hard disk and fill those forms with
your application’s ASCII print stream. Features include
„ Definition of page formatting and fonts
„ Duplexing with binding-margin offsets
„ Two-sided forms with text fill-in on front and/or back
„ “Gray bar” listing formats
„ Automatic page numbering
„ ANSI carriage-control recognition
„ Single- and multipart forms
„ Labels
„ Logos and watermarks
5"
QFORM doesn’t support color features.
Refer to the documentation that comes in the QFORM kit for installation and
usage instructions.
PlanetPress
PlanetPress is an electronic forms package that allows the creation and
modification of business forms, MICR checks, bar codes, and other
preprinted forms.
Refer to the documentation that comes in the PlanetPress kit for installation
and usage instructions.
122
QFORM
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
Interfaces and Daughterboards
Interfaces
Your printer supports the following interface cards:
„ CrownNet for Ethernet 10BaseT/100BaseTX (TCP/IP, NetWare, Ethertalk, LAN Manager/LAN Server) for an additional CrownNet for Ethernet
connection
„ CrownNet for Token-Ring (TCP/IP, NetWare, LAN Manager/LAN Server)
„ Crown for DECnet-TCP/IP
You can install one of these interface cards in addition to the two standard
interfaces—parallel and CrownNet for Ethernet (TCP/IP, NetWare, Ethertalk,
LAN Manager/LAN Server). The printer’s Simultaneous Interface Operation
(SIO) allows all of these interfaces to be active at the same time. In other
words, your printer can simultaneously communicate through all three ports
with three hosts, either computers or networks.
If installing a Token-Ring optional interface card, see the “Notices” section in
the Installation Guide for FCC compliance classification information.
What’s in the Kit?
An optional interface kit includes the following:
„ An interface card
„ Interface documentation (in hardcopy and/or on CD-ROM)
The kit may also include additional parts not required for network interface
installation on this printer.
Installation
Attention
It’s very important to protect the printer controller board and any
associated circuit boards from electrostatic damage. Before performing
this procedure, review the antistatic caution on page 105. In addition,
always handle circuit boards by the edges only.
Interfaces and Daughterboards
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
123
1
2
3
Turn off the printer, and then disconnect
the power cord and all interface cables
from the printer.
Loosen five screws and, using the tab on
the lower side of the panel, pull the
controller board from the printer.
Remove the two screws holding the metal
plate over the optional interface opening.
The optional interface opening is labelled
“Option.” It’s located next to the “Parallel”
port. Save the two screws. (You’ll use them
when you install the optional interface
card.) You can dispose of the plate
according to local regulations.
a Attach the interface card to the controller board.
... ...
III
... ... ... ... ... IIIIIIIIIIII
... ...
III
...
... ...
... ... ... ... ... IIIIIIIII
... ... ... ... ...
III
... ...
...
... ...
...
... ... ... ... ... IIIIIIIIIIII
... ... ... ... ...
... ...
III
...
... ...
... ... ... ... II III
...
... ... ... ... ...
... ...
... ... IIIIIIIII
... ...
...
... ... ... ...
... ... ... ... ... IIIIIIIIIIII
... ...
... ...
...
III
... ...
... ... ... ... IIIIIIII
... ...
... ... ... ... ...
... ... IIIIII
... ...
...
... ... ... . III
... ... ... ...
... .
... ...
... ...
... ... ... .
... .
b Position the interface card so that its I/O connector slides into its
opening in the interface panel and that its 80-pin connector aligns with
the 80-pin connector on the controller board.
c Gently press the interface card down until its connector is fully seated
and the card is secured by the plastic support post(s).
Attention
Make sure that the connectors on the interface card and controller
board are properly aligned. Damage to the interface card and/or
controller board could result if the pins are misaligned.
4
5
124
Secure the interface card to the interface panel with the two screws you
removed earlier.
Reinstall the controller board.
Interfaces and Daughterboards
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
Gently slide the controller board into the printer until it is fully seated, and
then tighten the five screws.
6
7
8
Reconnect all interface cables.
Reconnect the power cord, and turn on the printer.
5"
In compliance with UL guidelines, “The appliance inlet is
considered to be the main disconnect device.”
Print a startup page.
Check that the startup page lists the interface (Optional NIC) just installed
under “Options.”
Using a Network Interface
Once a network interface is installed, refer to the Installation Guide and the
CrownBook for information on connecting to the network, installing the
software, and configuring the interface and the network. You can also use the
documentation that came with the interface.
SCSI Interface
The optional SCSI interface allows you to connect up to three optional SCSI
devices, including a hard disk, and Jaz and Zip drives. These devices provide
storage for fonts, emulations, and other files; increase the number of pages
that can be collated; and provide a secondary storage area for spooled data,
while providing virtual memory capabilities.
What's in a Kit?
An optional SCSI interface kit includes the following:
„ SCSI interface card
„ SCSI interface card ribbon cable
„ Connector face plate
„ Two larger screws
„ Two smaller screws
SCSI Interface
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
125
Installation
Attention
It’s very important to protect the printer controller board and any
associated circuit boards from electrostatic damage. Before performing
this procedure, review the antistatic caution on page 105. In addition,
always handle circuit boards by the edges only.
1
2
3
4
5
Turn off the printer, and then disconnect
the power cord and all interface cables
from the printer.
Loosen five screws and, using the tab on
the lower side of the panel, pull the
controller board from the printer.
Remove the two screws holding the metal
plate over the SCSI interface opening.
You can dispose of the metal plate and
screws according to local regulations.
Attach the SCSI
interface card to
the controller
board.
a Position the
SCSI interface
card so that its
ribbon cable
connector
aligns with the
SCSI connector on the controller board.
...
.... ..
.... ....
.... ....
............
... ...
III
... ... ... ... ... IIIIIIIIIIII
... ...
III
...
... ...
... ... ... ... ... IIIIIIIII
... ... ... ... ...
III
... ...
...
... ...
...
... ... ... ... ... IIIIIIIIIIII
... ... ... ... ...
... ...
III
...
... ...
... ... ... ... II III
...
... ... ... ... ...
... ...
... ... IIIIIIIII
... ...
...
... ... ... ...
... ... ... ... ... IIIIIIIIIIII
... ...
... ...
...
III
... ...
... ... ... ... IIIIIIII
... ...
... ... ... ... ...
... ... IIIIII
... ...
...
... ... ... . III
... ... ... ...
... .
... ...
... ...
... ... ... .
... .
...
.... ..
.... ....
.... ....
............
b Gently press
the ribbon cable
connector down until it’s fully seated.
Attention
Make sure that the connectors on the ribbon cable and the controller
board are properly aligned. Damage to the controller board could
result if the pins are misaligned.
c Insert the SCSI interface card connector into its opening in the
interface panel.
126
SCSI Interface
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
d Secure the SCSI interface card to the interface panel with the two
larger screws in the kit.
5
Reinstall the controller board.
Gently slide the controller board into the printer until it’s fully seated, and
then tighten the five screws.
6
7
8
Reconnect all interface cables.
Reconnect the power cord and turn on the printer.
5"
In compliance with UL guidelines, “The appliance inlet is
considered to be the main disconnect device.”
Print a startup page.
Check that the startup page lists the interface (SCSI) just installed under
“Options.”
Using a SCSI Interface
5"
Installing a SCSI interface allows the attachment of external SCSI
storage devices, such as hard drives, JAZ, and ZIP drives. Installing
the SCSI interface kit will not allow you to print via SCSI.
Internal IDE Hard Disk Drive
Attention
Make sure that the printer and all accessories are turned off before
installing accessories involving the controller board.
One optional internal IDE hard disk is supported on the GN model.
What's in the Kit?
The IDE hard disk kit includes the following:
„ IDE hard disk with ribbon cable attached
„ IDE hard disk bracket
„ 4 screws
Internal IDE Hard Disk Drive
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
127
Installation
Attention
It’s very important to protect the printer controller board and any
associated circuit boards from electrostatic damage. Before performing
this procedure, review the antistatic caution on page 105. In addition,
always handle circuit boards by the edges only.
When installing or removing a hard disk, make sure that the metal
support posts (on the hard disk) don’t hit any of the electrical leads on
the chips mounted on the controller board. The controller board will not
function if any of the leads are broken or shorted together.
1
2
3
4
Ensure that the printer is turned off and the power cord and all interface
cables are disconnected.
Loosen five screws from the controller
board and, using the tab on the lower side
of the panel, pull the controller board from
the printer.
Position the controller board on a flat
surface so the controller board lies flat and
the interface panel is facing you.
Attach the IDE hard disk to the hard disk
bracket.
Attach the IDE hard disk to the bracket with
the grooved-end of the bracket facing the
ribbon cable. The screw holes in the bottom
of the hard disk should match up with the
128
Internal IDE Hard Disk Drive
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
holes on the hard disk bracket. Fasten the hard disk to the bracket with
the screws provided.
... ...
III
... ... ... ... ... IIIIIIIIIIII
... ...
III
...
... ...
... ... ... ... ... IIIIIIIII
... ... ... ... ...
III
... ...
...
... ...
...
... ... ... ... ... IIIIIIIIIIII
... ... ... ... ...
... ...
III
...
... ...
... ... ... ... II III
...
... ... ... ... ...
... ...
... ... IIIIIIIII
... ...
...
... ... ... ...
... ... ... ... ... IIIIIIIIIIII
... ...
... ...
III
...
... ...
... ... ... ... IIIIIIII
... ...
... ... ... ... ...
... ... IIIIII
... ...
...
... ... ... . III
... ... ... ...
... .
... ...
... ...
... ... ... .
... .
5
6
Position the hard disk so that the four support posts face the controller
board, the colored stripe on the ribbon cable faces away from you, and
the connector is down.
Insert ribbon cable connector pin 1 (the colored stripe side of the cable) in
hard disk connector pin 1.
Attention
Make sure that the ribbon cable connector and the controller board
connector pins are properly aligned. Damage to the controller board
could result if the pins are misaligned.
7
Press down gently but firmly on the cable connector until it is fully seated.
Attention
Do not push or pull with the ribbon cable. Use the cable connector.
8
Align the support posts with the holes on the controller board, and then
press down to secure the hard disk to the controller board.
So that you don’t stress the board, press one corner at a time to secure
the hard disk to the controller board.
If you’re installing DIMMs, go to the next section.
Otherwise, reinstall the controller board into the printer. Gently slide the
controller board into the printer until it is fully seated, and then tighten the
five screws.
When you print a startup page (page 42), verify that the hard disk is listed.
Internal IDE Hard Disk Drive
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
129
Lower Feeder Unit
Installing a Lower Feeder Unit (LFU)
Read this section if you purchased a lower feeder unit.
Kit Contents
L
„ Lower feeder unit with a letter/
A4/legal media tray (500 sheets)
R
„ 3 metal brackets
– Bracket L (1)
– Bracket R (1)
– Bracket B (1)
B
„ 2 securing thumbscrews
Installation
Attention
If consumables are installed in the printer, be sure to keep the printer
level when moving it to prevent accidental spills.
If your printer is located in its permanent location, follow this procedure.
Otherwise, skip to step 3.
1
Pull out the two carrying bars on
the right side of the printer.
WARNING!
Your printer weighs approximately 103.4 lbs (47.4 kg) with
consumables. Be sure to have help when lifting and moving it.
ACHTUNG! Das Gewicht dieses Druckers beträgt mit
Verbrauchsmaterial ca. 47.4 kg. Bitte versuchen Sie niemals, den
Drucker alleine anzuheben oder zu transportieren.
130
Lower Feeder Unit
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
2
3
4
5
6
7
With one person holding the carrying bars and another holding the two
grips on the left side of the printer, lift the printer and temporarily move it
to a flat, level surface.
Remove the lower feeder unit from the shipping carton, and place it where
the printer will be located.
Slide out the optional media tray from lower feeder unit.
Remove any tape and
packing material.
Put media in the optional
tray.
Slide the optional media
tray all the way into the lower
feeder unit.
5"
8
If you have removed the
tray from the lower feeder
unit, slightly tilt up the front
of the tray to insert it into
the guide rails to slide it
back in.
Slightly tilt up the printer’s upper
media tray to remove it.
Lower Feeder Unit
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
131
9
With another person’s help, lift the
printer.
When lifting and carrying the printer,
use the pull-out carrying bars c and
the hand grips d.
d
c
10
11
132
Slowly lower the printer onto
the lower feeder unit, lining
up the four holes in the
bottom of the printer with the
corresponding pins in the
lower feeder unit.
Place bracket L on the left
side of the printer frame
and secure it tightly with
the thumbscrew.
Lower Feeder Unit
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
12
13
Hold bracket R on a slant to
insert it from the front end
into the bracket R slot on
the right side of the printer
frame, then hold bracket R
level and secure it tightly
with the thumbscrew.
Unscrew the thumbscrew
from the rear of the printer.
5"
14
Retain this screw for use in
step 15.
Hold bracket B on a slant and
insert the front end into the
bracket B slot.
Lower Feeder Unit
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
133
15
Lift up bracket B and secure it tightly
with the thumbscrew.
Make sure the bracket matches the
position shown in the illustration.
16
Slide the upper media tray back into
the printer.
Media Trays
The printer comes with a 150-sheet multipurpose tray (tray 1), and a
500-sheet media tray (the upper tray—tray 2). The optional lower feeder unit
has another 500-sheet optional media tray that provides two main benefits:
„ Expanded flexibility to switch media size, color, and type without having to
unload and load media.
„ Increased media-feed capacity
Keep 500-sheet replacement trays close by, so you can easily change media
by slipping one tray out and another in.
Media trays accommodate only letter/A4/legal media.
Installation
1
134
Slide the existing media tray open.
Media Trays
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
2
Slide the new tray into the
printer.
5"
Slightly tilt up the
tray to insert it into
the installation rails
to slide it back in.
For information about loading
media, see “Using Media,” on
page 33.
Printer Stand/Cabinet
A tabletop- or floor-model printer stand or a cabinet is available. Follow the
assembly instructions included with it.
SC-210 Convenience Copier
You can expand your magicolor 2210’s functionality by connecting an SC-210
digital color convenience copier option to the standard parallel port on the
printer (interface set to “non-interactive”). The SC-210 supports up to
legal-size paper. An optional 25-sheet Automatic Document Feeder (ADF) is
available.
Check the documentation included with your SC-210 for instructions on
setup, configuration, and operation.
Included with the SC-210:
„ Software CD-ROM
„ Parallel cable (2)
„ Power adapter
„ User warranty and registration card
Time-of-Day Clock
The time-of-day clock provides time and date information on the startup page
and in the accounting data.
Printer Stand/Cabinet
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
135
Installation
Attention
It’s very important to protect the printer controller board and any
associated circuit boards from electrostatic damage. Before performing
this procedure, review the antistatic caution on page 101. In addition,
always handle circuit boards by the edges only.
1
2
Turn off the printer, and then disconnect the power cord and all interface
cables from the printer.
Loosen five screws and, using the tab on the
lower side of the panel, pull the controller
board from the printer.
WARNING!
Because the time-of-day clock includes an internal battery, there is a
danger of explosion if the clock is incorrectly installed or replaced.
Replace it only with a supported MINOLTA-QMS time-of-day clock.
Dispose of any used time-of-day clock in accordance with local laws
and regulations.
ACTUNG! Da der Uhrenbaustein eine interne Batterie enthält, besteht
Explosionsgefahr, falls dieser falsch eingesetzt oder ersetzt wird. Er
darf nur durch einen unterstützten Baustein ersetzt werden. Bitte
entsorgen Sie den Baustein gemäß den geltenden
Entsorgungsbestimmungen.
AVERTISSEMENT! Dû au fait que l’horloge interne de l’imprimante est
munie d’une batterie interne, il y a un risque d’explosion si celle-ci est
mal installée ou remplacée. La remplacer seulement avec une horloge
supportée par MINOLTA-QMS. Se départir de toute horloge interne
défectueuse en respectant les lois et réglementations en vigueur.
136
Time-of-Day Clock
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
3
Attach the time-ofday clock to the
controller board.
... ...
III
... ... ... ... ... IIIIIIIIIIII
... ...
III
...
... ...
... ... ... ... ... IIIIIIIII
... ... ... ... ...
III
... ...
...
... ...
...
... ... ... ... ... IIIIIIIIIIII
... ... ... ... ...
... ...
III
...
... ...
... ... ... ... II III
...
... ... ... ... ...
... ...
... ... IIIIIIIII
... ...
...
... ... ... ...
... ... ... ... ... IIIIIIIIIIII
... ...
... ...
III
...
... ...
... ... ... ... IIIIIIII
... ...
... ... ... ... ...
... ... IIIIII
... ...
...
... ... ... . III
... ... ... ...
... .
... ...
... ...
... ... ... .
... .
Attention
Make sure that the pins on the time-of-day clock are properly aligned
with those in the receiving socket on the controller board. Damage
to the time-of-day clock and/or controller board could result if the
pins are misaligned.
a Locate the time-of-day clock socket on the controller board and the pin
1 notch or printed label.
b Locate the pin 1 indicator mark on the top of the time-of-day clock.
This mark may be a notch or a slight depression on one end of the
clock.
c Align this indicator mark with the pin 1 notch or printed label on the
controller board.
d Gently press down on the time-of-day clock until it’s firmly seated.
5
Reinstall the controller board.
Gently slide the controller board into the printer until it is fully seated, and
then tighten the two screws.
6
7
8
Reconnect all interface cables.
Reconnect the power cord and turn on the printer.
5"
In compliance with UL guidelines, “The appliance inlet is
considered to be the main disconnect device.”
Print a startup page.
The time-of-day clock is not listed under “Installed Options” on the startup
page, but the time will appear as System Date in the Printer Information
column.
Time-of-Day Clock
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
137
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
Color Printing
6
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
Introduction
Your magicolor 2210 features advanced color laser technology that produces
inexpensive and durable color prints at 600x600, and 1200x1200 dpi on plain
paper, envelopes, labels, thick stock, and transparencies.
Color Management and Control
The magicolor 2210 offers a host of color screening, matching, and calibration tools for both the beginner and professional color user.
MINOLTA-QMS QCOLOR Technology
Color management does not mean all devices will match exactly. It does
ensure the closest possible color transformation. MINOLTA-QMS QCOLOR
technology offers four methods for color matching across devices:
„ MINOLTA-QMS QCOLOR automatic color correction
„ Supplied ICC printer profiles
„ Built-in color rendering dictionaries (CRDs)
„ Supplied PANTONE®* Color matching tables
MINOLTA-QMS QCOLOR technology takes the guesswork out of color reproduction by automatically optimizing color output. Now even a novice can
produce professional quality, colorized documents without the use of sophisticated manual optimization techniques.
The following is a summary of MINOLTA-QMS QCOLOR automatic color
correction features:
„ Ease of use across applications: With MINOLTA-QMS QCOLOR, it’s as
easy to get great color from a PowerPoint presentation as it is from a
desktop publishing application, such as QuarkXPress. MINOLTA-QMS
QCOLOR’s color matching methods are simple for both novice and professional color users to navigate.
„ Single-button control: Whether accessing through the printer driver, or
from the printer’s front panel, MINOLTA-QMS QCOLOR’s single-button
controls enable automatic correction of uncalibrated RGB or CMYK
color files.
„ Printer-resident CMS: Because MINOLTA-QMS QCOLOR automatic
color correction is built into the printer, it works well in all computing environments and with most design, publishing, and office applications.
*Pantone, Inc.’s check-standard trademark for color reproduction and color reproduction
materials.
140
Introduction
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
„ Industry-standard profiles: QCOLOR uses industry-standard ICC profiles for compatibility with popular input and output devices.
„ Supports host-based color management systems: Easily disable
MINOLTA-QMS QCOLOR automatic color correction when using
host-based ColorSync or ICM color matching.
„ Profiles for common monitors and output devices: MINOLTA-QMS
QCOLOR offers default color matching for a variety of common monitors
and printing presses.
„ Download device profiles: For custom color matching, QCOLOR supports downloaded (to disk only) ICC profiles.
„ Support for Internet standard: MINOLTA-QMS QCOLOR uses sRGB for
Internet-standard default color matching.
„ Individual page element correction: QCOLOR separately color corrects
(matches) graphics, text, and images on a singe page using printer-resident CRDs.
Further Information
For further information about the MINOLTA-QMS color management, refer to
the CrownBook.
Introduction
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
141
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
Repacking the
Printer
7
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
Storing the Printer
Keep the following in mind when storing the printer for an extended period:
1
2
Unplug the printer.
Remove the OPC drum, the fuser oil roller, and toner cartridges from the
printer and return them to their original packaging. If the original packaging is not available, protect the toner cartridges from spilling toner, and
protect the OPC drum cartridge from damage and light.
Relocating Your Printer
Occasionally, you may have to move your printer to a different location, either
nearby or to a distant location. To avoid damage to your printer, we advise
you to follow the next instructions very carefully.
1
2
3
4
Turn off the power to your printer.
If the printer has a lower feeder unit and/or a 5-bin mailbox, remove them.
If you are moving to a distant location, follow the instructions for repacking
the printer.
Relocate the printer.
WARNING!
Your printer weighs approximately 87.1 lbs (39.5 kg) without
consumables. Be sure to have help when lifting and moving it.
ACHTUNG! Das Gewicht dieses Druckers beträgt ohne
Verbrauchsmaterial ca. 39.5 kg. Bitte versuchen Sie niemals, den
Drucker alleine anzuheben oder zu transportieren.
5
6
Unpack and set up the printer in its new location.
Reinstall the accessories you removed in step 2.
5"
We strongly suggest that you save the packaging materials in
case you ever need to move or ship the printer.
Refer to the Service & Support Guide or www.minolta-qms.com for additional
information on where to obtain assistance if necessary
144
Storing the Printer
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
Repacking the Printer
Attention
Failure to follow these instructions could result in voiding your
warranty.
If you need to relocate or ship your printer after it’s been installed, follow the
procedures in this chapter to prevent damage to the printer and to keep your
warranty valid.
5"
We strongly suggest that you save the packaging materials in case
you ever need to move or ship the printer. If you’re returning just the
printer for service, do not return the interface cables, power cable,
documentation, media tray(s), or accessories.
Attention
MINOLTA-QMS cannot be held responsible for damage to your printer
during shipment that results from the improper packaging of your
printer. You must use the instructions given in this section before
repacking the printer in its original shipping carton with the original
packing materials. Original shipping cartons are secured to a pallet
using disposable strapping and buckling supplies. These supplies must
be replaced prior to shipping the printer. If you need replacement
packaging, in the United States, call MINOLTA-QMS Spares at
(251) 633-4300 extension 2530 and request catalog number
2600674-901. For locations outside the United States, refer to the
Service & Support Guide or www.minolta-qms.com. If you return the
printer for service, be sure to write the RMA (Return Merchandise
Authorization) number you received from your customer support
representative on the outside of the carton before shipping the printer.
If the printer is not strapped to the pallet or if the RMA number is not
prominently visible on the outside of the return inventory, we will not
accept receipt. You can also have a MINOLTA-QMS authorized service
provider uninstall and repack your printer. For prices and availability,
call 1 (877) 778-2657.
What's Involved?
Repacking your printer for shipment involves the following steps. Each is
described in more detail in the following sections.
1
2
145
Remove the cables.
Remove the fuser oil roller.
Repacking the Printer
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
3
4
5
6
7
8
9
10
Remove the toner cartridges.
Remove the waste toner pack.
Remove the OPC drum.
Remove the transfer belt.
Remove the duplex unit (if attached).
Remove the 5-bin mailbox (if attached).
Remove the lower input feeder (if attached).
Repack the printer for shipment.
To avoid toner contamination during shipment, the printer should be repacked
without the fuser oil roller, toner cartridges, waste toner pack, OPC drum cartridge, or transfer belt installed.
Remove the Cables
1 Turn off the printer.
2 Remove the power cable and all interface cables.
Remove the Fuser Oil Roller
WARNING!
The fuser unit can become extremely hot and cause severe
burns. Make sure the unit is cool before handling it.
ACHTUNG! Die Fixiereinheit kann sehr heiß werden, so daß
Verbrennungsgefahr besteht. Bitte lassen Sie die Fixiereinheit einige
Zeit abühlen, bevor Sie diese berühren.Open the printer’s top cover.
3
4
5
6
Rotate the two lock levers to release the fuser oil roller.
Remove the fuser oil roller.
Store the fuser oil roller in its original shipping bag.
Close the printer’s top cover.
Remove the Toner Cartridges
1 Open the printer’s front cover.
Remove the Cables
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
146
2
Remove the four toner cartridges and store them in their original packaging. If the original packaging is not available, protect the toner cartridges
from spilling toner.
Remove the Waste Toner Pack
1 With the printer’s front cover open, remove the waste toner pack from
the printer.
2
3
Use the three plugs on the side of the waste toner pack to seal
the opening.
Store the waste toner pack in its original packaging.
Remove OPC Drum Cartridge
Remove the OPC drum cartridge and store it in its original packaging. If the
original packaging is not available, protect the OPC drum cartridge from damage and light.
Remove Transfer Belt
1 Remove the transfer belt and store it in a plastic bag in a box to avoid
toner spillage.
2
Close the printer’s front cover.
Remove the Duplex Unit
5"
1
2
3
4
5
If you don’t have a duplex unit installed, skip to the next section.
Open the duplex cover and unhook the spring wire.
Loosen the two thumbscrews until the duplex unit moves freely away from
the right side of the printer.
Lift duplex unit up and away from the printer.
Install the original right-side cover that came with the printer.
Repack the duplex unit in its original shipping carton for storage or
shipment.
5" If you’re returning the printer for service, you don’t need to return the
duplex unit, unless the problem is with the duplex unit.
147
Remove the Waste Toner Pack
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
Remove the 5-bin Mailbox
5"
1
2
3
4
5
If you don’t have a 5-bin mailbox installed, skip to the next section.
Remove the power cable.
Remove the side plates and loosen the thumbscrews.
Lift 5-bin mailbox up and away from the printer.
Replace the original screen covers on the top of the printer.
Repack the 5-bin mailbox in its original shipping carton for storage or
shipment.
5" If you’re returning the printer for service, you don’t need to return the
5-bin mailbox, unless the problem is with the 5-bin mailbox.
Remove the Lower Feeder Unit
5"
1
2
3
4
5
If you don’t have a lower feeder unit installed, skip to the next section.
Remove the rear bracket securing the lower feeder unit to the printer.
Remove the upper media tray.
Remove the brackets on the right and left in front that are securing the
optional tray to the printer.
Replace the upper media tray.
With the help of another person, lift the printer by its carrying grips and
carrying bar, and place the printer on a table.
WARNING!
Your printer weighs approximately 87.1 lbs (39.5 kg) without
consumables. Be sure to have help when lifting and moving it.
ACHTUNG! Das Gewicht dieses Druckers beträgt ohne
Verbrauchsmaterial ca. 39.5 kg. Bitte versuchen Sie niemals, den
Drucker alleine anzuheben oder zu transportieren.
Remove the 5-bin Mailbox
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
148
6
Repack the lower feeder unit in its original
shipping carton for storage or shipment.
5" If you’re returning the printer for service,
you don’t need to return the lower
feeder unit, unless the problem is with
the lower feeder unit.
Repack the Printer
If you need replacement packaging, in the United States, call MINOLTA-QMS
Spares at 1 (251) 633-4300 extension 2530 and request part number
2600674-901 for the repacking kit. Refer to the Service & Support Guide or
www.minolta-qms.com for locations outside the United States.
1
2
3
4
149
Place the lower cushions into the shipping
carton’s base.
Put the printer’s plastic bag into the shipping
carton’s base.
With another person’s help, put the printer into
its plastic bag and tape the bag closed.
Replace the outer shipping carton over the
printer and the base, and secure the shipping
carton using the plastic interlocks that came
with the original carton.
Repack the Printer
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
5
6
Pack the printer
for shipment as
shown.
If you’re also
shipping the
power cord and
any manuals with
the printer, place
them in the
shipping carton.
5" Don’t ship
these items
if you’re
returning the
printer
for service.
7
Securely tape the
top flaps of the
shipping carton
closed.
Strapping/Buckling Kit Contents
4 lengths of strapping precut to the
appropriate length
4 buckles to secure the strapping
Repack the Printer
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
150
Strapping/Buckling Instructions
1
2
3
4
5
6
151
Thread one end of the
strapping through the
wooden pallet.
Pull the two ends of the
strapping together at the
approximate center of the
top of the printer.
Thread both ends up
through the center of the buckle.
Weave the slack of
one end through
the buckle.
Pull the slack on
that end so
that the strapping
is taut in
the buckle.
Weave the slack of the other end through the buckle.
Repack the Printer
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
7
8
Pull all of the
remaining slack
of the strapping
through this side
of the buckle,
until the buckle is
taut against the printer box.
Pull the buckle against the printer as tightly as possible.
Some slack may still exist.
9
10
Repeat this procedure
three more times, spacing
the straps equidistant
across the box.
Write the RMA number
prominently on the carton.
RMA #
Repack the Printer
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
152
Technical
Specifications
A
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
Requirements
Space Requirements
The illustration below shows the amount of space required for operating the
printer, replacing supplies, and removing media jams.
Top View
4" (100 m m )
16" (400 m m )
Height 37" (950 m m )
4" (100 m m )
38" (950 m m )
Front
18" (450 m m )
38" (950 m m )
If you have added accessories, the printer’s height will increase by
154
Lower feeder unit
4.6" 116.5 mm)
Duplex unit
0" (0 mm)
5-bin mailbox
15.34" (400 mm)
Requirements
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
Power Requirements
Power
Japan
100 VAC 50–60 Hz 12 amps
North America 120 VAC 50–60 Hz 8 amps
Europe
220–240 VAC 50–60 Hz 6 amps
Latin America 120 VAC 50–60 Hz 8 amps
220–240 VAC 50–60 Hz 6 amps
Voltage
Fluctuation
Rate
Japan
100 VAC ±10%
North America 120 VAC ±10%
Europe
220–240 VAC ±10%
Latin America 120 VAC ±10%
220–240 VAC ±10%
Frequency
Variation Rate
Within 50–60 ±3 Hz
Location Requirements
„ On a hard, flat, level (1° or less slant at any point around the machine)
surface capable of supporting the printer, accessories, consumables, and
media. Weights are shown below.
Component
Weight
Printer
87.1 lbs (39.5 kg)
Consumables (such as toner,
OPC drum)
11 lbs (5.0 kg) (total)
Media
5.2 lbs (1.9 kg) per ream of 20 lb
bond (75 g/m2) paper
Lower feeder unit (each)
14.8 lbs (6.7 kg)
Duplex unit
5.3 lbs (2.4 kg)
5-bin mailbox
15.5 lbs (7.0 kg)
5"
A surface can be tested for levelness with a standard round pencil.
If the pencil rolls, the surface is not level. Clear the area of any
obstruction or items such as cables that might prevent the printer
from sitting directly on the flat, level surface.
„ In an area with an ambient temperature range of 50°–95° F (10°–35° C)
and relative humidity range of 15%–85% (noncondensating).
Location Requirements
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
155
„ Away from cooling and heating sources, extreme temperature or humidity
changes, direct sunlight, excessive dust, corrosive chemicals or vapors
(such as ammonia), water pipes, refrigerators, and any strong electromagnetic field (such as that created by an air conditioner), open flames,
or items that can easily burn, or items that produce excessive vibration.
If the printer is located in a cold room that is rapidly heated, or if the printer
is moved from a cold place to a warm, humid place, condensation may
occur within the printer, degrading print quality. If this occurs, allow the
printer to adapt to the environment for about one hour before use.
„ Away from water.
If using a humidifier or water vaporizer in the room with the printer, use
only purified or distilled water. Impurities in the water may be released into
the air, where they can accumulate inside the printer and cause degraded
printer output.
„ Away from open flames or items that can easily burn.
„ At an altitude of 0–8202' (0–2500 m).
„ Away from items that produce excessive vibration.
„ Near your computer—6.5' (2 m) or less for an IEEE 1284 bidirectional parallel connection; cables for other connections may be longer.
„ Close to an easily accessible grounded power supply on an exclusively
dedicated power outlet.
WARNING!
Do not connect the groundwire to gas or water pipes or grounding for
telephones.
Achtung! Das Massekabel keinesfalls an eine Gas- oder Wasserleitung
oder eine Erdung für Telefone anschließen.
„ Not connected to the same electrical outlet as noise-generating equipment. If the printer is connected to the same circuit used by other
high-current machines, such as a copier or air conditioner, or to an electrically noisy machine, low voltage or noise may cause overheating, computing errors resulting in data loss, and improper performance.
„ In a well-ventilated area, but away from wind.
„ With enough space to allow adequate ventilation and easy servicing.
WARNING!
Obstructing the ventilation grilles could present a fire hazard.
Achtung! Abdeckung der Ventilator-Schlitze kann ein Feuer auslösen.
156
Location Requirements
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
Computer Requirements
Printer performance depends upon the type of computer to which you connect it. We recommend a Pentium-class computer with at least 16 MB of
RAM (if you’re using Windows Me/98/95) or 32 MB of RAM (if you’re using
Windows 2000/NT4).
ENERGY STAR Compliance
All models of the magicolor 2200
Series are compliant with US Environmental Protection Agency (EPA)
ENERGY STAR regulations. After a
specified period of inactivity, the printer
changes to a low-power state (the
engine remains on, but the fuser turns
off). When a print job is received, the
printer returns to normal power within
a user-configurable time period.
Engine and Controller Specifications
Engine
Minolta NC-L4001
Engine
Duty cycle
5"
Simplex letter/A4
pages per month
8,000 average prints and up to
35,000 maximum prints per month*
*The duty cycle will be affected by the media type, percent coverage,
and the number of monochrome versus color pages.
Print Speed—Simplex
The following table defines the maximum print speed in Pages Per Minute
(ppm).
Page size
Monochrome ppm
4-Color ppm
A4
20
5
Letter
20
5
Legal
20
4*
Engine and Controller Specifications
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
157
Transparency Film (A/ 3.8
A4)
2.4
Label (A/A4)
3.8
2.4
Thick (A/A4)
3.8
2.4
Print Speed—Autoduplex
The following table defines the maximum print speed in Pages Per
Minute (ppm).
Page size
Monochrome ppm
4-Color ppm
A4
10
2.5
Letter
10
2.5
Legal
10
1.5
General
158
Printer type
Desktop, non-impact, 4-color printer
Print method
Scanner: Semiconductor laser with rotating mirror
Recorder: Black writing electrophotographic
Process: Cyan, magenta, yellow, and black dry toner
image transfer to print media
Fuser: Heated rollers
Resolution
Standard: 1200x1200 dpi
Toner
Type: Microfine, dry, single component
Packaging: User-replaceable cartridges
Warm-up time
Maximum: 110 volts: 150 seconds
220 volts: 160 seconds
Input sources
Standard: 500-sheet tray
150-sheet multipurpose tray
Optional: 500-sheet lower input feeder
Output
250-sheet tray on top of printer
Engine and Controller Specifications
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
Controller
CPU
IDT RC64574
Resident
emulations
PostScript—Level 3 (600/1200 dpi)
HP PCL—PCL5c, PCL XL, PCL5e/GL2 (HP PaintJet
XL300 compatible; 600 dpi; 600/1200 dpi, GL2 only)
PDF—Version 1.2
HP-GL—7475A/7550/Draftmaster (600 dpi)
Lineprinter—(600 dpi)
Optional
emulations
ImageServer (monochrome only)
CGM
LN03 Plus(300 dpi monochrome only)
Fonts
PostScript—137 resident PostScript fonts that can be
scaled from 4 points upward and rotated to any angle
in 1° increments; all typefaces have multilingual
character sets
HP PCL 5e, 5c—80 scalable and 4 bitmapped fonts
PCL XL—45 scalable and 9 bitmapped typefaces
HP-GL—40 resident HP-GL symbol sets
Type 1 / Type 3 Support—Support for Type 1 and Type
3 host-resident downloadable PostScript fonts
TrueType—Support for Type 42 (PostScript format)
host-resident downloadable TrueType fonts, support
for TrueType fonts in PCL
Kanji fonts
Hard disk—MINOLTA-QMS Kanji Internal IDE Hard
Disk
with 7 Morisawa fonts (Ryumin-Light-KL,
GothicBBB-Medium, FutoMinA101-Bold,
FutoGoB101, Jun101-Light, MidashiMin-MA31,
and Midashi Go-MB31)
Standard
interfaces
CrownNet for Ethernet—10BaseT/100BaseTX
Optional
interfaces
Network interface—Support for one optional network
interface (CrownNet for Ethernet, supporting
EtherTalk, LAN Manager/LAN Server, Netware, and
TCP/IP; CrownNet for Token-Ring, supporting LAN
Manager/LAN Server, NetWare, and TCP/IP; or
Crown for DECnet-TCP/IP)
Parallel—Centronics/IEEE 1284 bidirectional
SCSI interface—Support for up to 3 external SCSI hard
disks (up to 2.2 GB)/Jaz drives/Zip drives
Engine and Controller Specifications
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
159
RAM
Type: PC-100 Compliant SDRAM DIMMs
Base system RAM: 128 MB
Total RAM: Upgradable to 384 MB (through 3 DIMM
connectors)
Optional RAM
32, 64, and 128 MB DIMMs
System
software
Softloadable; stored in Flash ROM
Internal IDE
hard disk
Optional, up to 2.2 GB
5" For information about hard disks recommended
for your printer, see the magicolor 2210 Answer
Base through the Internet at http://
www.minolta-qms.com/support/, or contact
Technical Support (see the Service & Support
Guide for a complete listing of support telephone
numbers).
Time-of-day
clock
Optional (socket provided for)
Job
accounting
Crown job accounting; requires an optional IDE drive
Warning
function
convenience
Optional, BuzzBox (light/buzzer printer warning device);
operates over a parallel connection
Convenience
copier
Optional, SC-210 operates over a parallel connection
Electrical
Voltage and Power
Voltage and
frequency
US: 120 volts ±10% at 50–60 Hz ±3 Hz
Japan: 100 volts ±10% at 50–60 Hz ±2 Hz
International: 220-240 volts +10% at 50–60 Hz ±3 Hz
Phase
Single
Power
consumption
Mode
Maximum
Operation
100/120 volts—1000 watts
220 volts—1100 watts
250 watts
45 watts
Standby
Power saver
Compliance
160
ENERGY STAR compliant
Engine and Controller Specifications
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
Environmental
Noise level
Printing: Less than 55 dB (A)
Standby: Less than 41 dB (A)
Relative
humidity
Operating: 15-85% RH (noncondensing)
Transportation/Storage: 30–85% RH (noncondensing)
Temperature
range
Operating: 50-95° F (10-35° C)
Transportation/Storage: 32-95° F (0-35° C)
Altitude
Operating: 0-8202 ft (0-2500 m)
Inclination
Operating: 1° or less slant at any point around the
machine
Ambient Humidity (%RH)
Optim al Operating Range
Acceptable Operating Range
80
70
60
50
40
30
20
10
0
10
50
17.5 20
63.5 68
27 30 32.5 Cº
80.6 86 95 Fº
Am bient Tem perature
Engine and Controller Specifications
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
161
Physical
Main Body
Main Body with
Lower Input
Feeder
Main Body with
Duplex Unit and
Lower Input Feeder
Dimensions W: 18.2 in. (463
mm)
H: 20.6 in. (511
mm)
D: 21.3 in. (522
mm)
W: 18.2 in. (463
mm)
H: 22.0 in. (560
mm)
D: 21.3 in. (522
mm)
W: 18.2 in. (463 mm)
H: 22.0 in. (560 mm)
D: 21.3 in. (522 mm)
Weight
(excluding
consumables)
Unpacked:
Printer: 87.1 lbs
(39.5 kg)
Lower Input
Feeder:
13.2 lbs (6.0 kg)
Unpacked:
Printer: 87.1 lbs (39.5
kg)
Lower Input Feeder:
13.2 lbs (6.0 kg)
Duplex Unit: 3.7 lbs
(1.7 kg)
Shipping*:
Printer: 117 lbs (53
kg)
Lower Input
Feeder:
31 lbs (14 kg)
Shipping*:
Printer: 117 lbs (53
kg)
Lower Input Feeder:
14.8 lbs (6.7 kg)
Duplex Unit: 5.3 lbs
(2.4 kg)
Unpacked:
87.1 lbs (39.5 kg)
Weight
Shipping: 117 lbs
(including (53 kg)
consumabl
es)
Notes
* Shipped separately.
Print Media
162
Delivery—
Output
Tray
Output: Face-down
Tray Capacity: 500 sheets of 20 lb bond (75 g/m 2) paper
Delivery—
Mailbox
Output: Face-down
Mailbox Bin Capacity: Each bin holds approximately 50
sheets of 16–24 lb (60–90 g/m2) bond letter/A4 paper only
Input sources
Upper input feeder (500-sheet tray): Paper,
transparencies
Optional lower input feeder (500-sheet tray): Paper,
transparencies
Multipurpose tray (150 sheet): Envelopes, labels, paper,
thick stock, transparencies
Print Media
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
Media sizes,
types, and
weights
See “Media Types” on page 35.
Notes
The maximum media weight supported for duplex printing
is 24 lb bond (90g/m2).
Document Option Commands
This lists the supported Document Option Commands (DOCs) for your magicolor 2210. The commands are grouped by feature type.
Each command is preceded by either a DOC statement (%%) or an IncludeFeature statement (%%IncludeFeature). See the Crown Document Option
Commands manual for information on all other commands.
Supported DOCs
Header/Trailer Page Commands
Print charge number
Print copyright statement
Print document creator
Print creation date and time
Print current date
End comments
Print document owner
Print document host
Job completion notification via email
Select page order
Save job for reprinting (proof and print)
Print routing information
Print document title
Print version and revision
Print header page
Print trailer page
%%ChargeNumber
%%CopyRight:
%%Creator:
%%CreationDate:
%%Date:
%%EndComments
%%For:
%%Host:
%%Page
%%Notify
%%PageOrder
%%Retain: proof
%%Routing:
%%Title:
%%Version:
%%IncludeFeature: header
%%IncludeFeature: trailer
HP-GL Emulation Commands
Select enhanced resolution
Expand plot
Select original paper size
%%IncludeFeature: enhanced
%%IncludeFeature: expand
%%IncludeFeature: size
Document Option Commands
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
163
Select pen width and color
Select plotter
Scale the image
Set origin
%%IncludeFeature: pen
%%IncludeFeature: plotter
%%IncludeFeature: scaling
%%IncludeFeature: origin
HP PCL 5e Emulation Commands
Install object
Remove object
Remove resource
Retain temporary
Select default font
Select default font ID
Reset
Select scalable fonts
Select symbol set
Set carriage return to CR+LF
Set linefeed to CR+LF
Set number of lines per inch
Set point size
Resource
%%IncludeFeature: install
%%IncludeFeature: remove
%%IncludeFeature:
removeresource
%%IncludeFeature:
retaintemporary
%%IncludeFeature: font
%%IncludeFeature: fontid
%%IncludeFeature: reset
%%IncludeFeature: scalablefonts
%%IncludeFeature: symbolset
%%IncludeFeature: criscrlf
%%IncludeFeature: lfiscrlf
%%IncludeFeature: linesperinch
%%IncludeFeature: pointsize
%%IncludeFeature: resource
Lineprinter Emulation Commands
Select font for current job
Set point size for current job
Specify character map type
Number lines
Set tabs
Set linefeed to CR+LF
Set carriage return to CR+LF
Set formfeed to CR+FF
Wrap lines
Set number of lines per page
Set margins
Set orientation
%%IncludeFeature: font
%%IncludeFeature: pointsize
%%IncludeFeature: map
%%IncludeFeature: number
%%IncludeFeature: tabs
%%IncludeFeature: lfiscrlf
%%IncludeFeature: criscrlf
%%IncludeFeature: ffiscrff
%%IncludeFeature: autowrap
%%IncludeFeature: linesperpage
%%IncludeFeature: lpmargins
%%IncludeFeature: lporientation
CCITT Groups 3 and 4 Commands
Start decompression
Set encoded byte flag
Set end of block
Set line end
164
%%ImageData
%%EBAMode
%%BlockEnd
%%LineEnd
Supported DOCs
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
Eject page
Set image position
Invert image
Set dpi for image expansion
Set data compression
Reverse bits
End print job
Set image size
Set image rotation
Set source image origin
Set source image position
%%PageEnd
%%ImagePosition
%%InvertImage
%%DPI
%%Compression
%%BitReverse
%%JobEnd
%%ImageSize
%%Rotation
%%SourceImageOrigin
%%SourceImagePosition
Document Formatting
Logical page orientation
Number up printing
Offset logical page
Print borders
Scale logical page
Print background images
Set printer resolution
Print page range
Duplex printing
Collate print job
Logical page size
Select number of copies
Select paper
Select orientation
Select emulation
Logical margins
Select color separations
Select color or monochrome
Media type
Select Output Bins
Select New Layout
%%IncludeFeature:
pageorientation
%%IncludeFeature: pagegrid
%%IncludeFeature: pageoffsets
%%IncludeFeature: border
%%IncludeFeature: pagescaling
%%IncludeFeature: background
%%IncludeFeature: resolution
%%IncludeFeature: pagerange
%%IncludeFeature: duplex
%%IncludeFeature: collate
%%IncludeFeature: pagesize
%%IncludeFeature: numcopies
%%IncludeFeature: input
%%IncludeFeature: orientation
%%IncludeFeature: emulation
%%IncludeFeature: margins
%%IncludeFeature:
colorseparation
%%IncludeFeature: colormodel
%%IncludeFeature: mediatype
%%IncludeFeature: output
%%IncludeFeature: newlayout
Job and Subjob Boundary Commands
Sessions (only via network interface)
End of document
%%Sessions
%%EndOfDocument
<ESC>%-12345x
Supported DOCs
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
165
LN03 Plus Commands
Identify product
Control line wrap
Specify default paper size
Control transformation point
Adjust image horizontally
Adjust image vertically
Set power-up configuration
166
%%IncludeFeature: product
%%IncludeFeature: autowrap
%%IncludeFeature: paper_size
%%IncludeFeature:
paper_size_override
%%IncludeFeature: xorigin
%%IncludeFeature: yorigin
%%IncludeFeature:
reset_override
Supported DOCs
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
Index
1.5° slant 75, 82
1200x1200 dpi printing 105
600x600 dpi printing 105
A
Acc already disabled message 86
Acc disabled message 86
Acc enabled message 86
Acc file x% full message 86
Acc files got removed message 86
Accessories
5-bin mailbox 100
BuzzBox 100
CGM 100
Crown for DECnet-TCP/IP 100
CrownNet for Ethernet 100
CrownNet for Token-Ring 100
Daughterboards 100
DIMMs 103
Dual In-Line Memory Modules
(DIMMs) 100
Duplex unit 107
Emulations 100
Fonts 100
Hard disk 127
ImageServer 100
Installation 101
Interfaces 100
Internal IDE hard disk drive 100
Kanji font internal IDE hard disk 100
LN03 100
LocalTalk 100
Lower input feeder 130
Media tray 100
Other software 100
PlanetPress 100
Printer cabinet 135
Printer stand and/or cabinet 100
QFORM 100
SC-210 convenience copier 101
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
SCSI 100
Time-of-Day Clock 101
Active jobs message 85
Additional memory 103
Advanced printing features
Memory 104
AIDC 84
Cycle 73
Sensor 75
ANSI 122
Antistatic protection 101
ASCII 122
Autoduplex 40
Print speed 158
Auto-Image Density Control (also
known as AIDC) 75
Automatic jam recovery 53
B
Basic performance 104
BuzzBox 100, 101
Installation 102
C
Cable
Removing 146
Cancel all jobs message 87
Cancel job message 87
Cancelling job
Status message 87
Cassette (see tray) 134
CGM 112
Check waste toner message 87
Cleaning
AIDC sensor 75
Cleaning solutions 48
Image darkness sensor 75
Codes
Error 97
Color
Color Rendering Dictionaries
(CRDs) 140
PANTONE© 140
Profiles 141
QCOLOR Technology 140
See also the CrownBooks 141
Consumables
Life Expectancy 6
Replacement 6
Continuous printing 40
Control panel messages 85
Controller
Board removal 106
Specifications 159
Convience copier 101
Cooldown pause 87
CRDs 140
Created files message 88
Creating x file message 88
D
Default memory 105
DIMMs 103
Additional 104
DOC
See Document Options Commands
Document Option Commands
Header/trailer page 163
HP PCL 5e emulation commands 164
HP-GL emulation commands 163
Job and subjob boundary
commands 165
Lineprinter emulation commands 164
LN03 commands 166
Dual In-Line Memory Modules
See DIMMs 103
Duplex
Definition 7
Manual duplexing 55
Printing 40
Duplex unit 107
Duty cycle 157
E
Electrostatic discharge 101
Emulation 112
Downloading optional 112
End job message 88
End job? message 93
ENERGY Star 157
168
Index
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
Envelopes
Formatting 37
Loading 46
Printing 37, 45, 46
Environmental requirements 161
Error codes 97
Error message 85
Bins 92
Fuser 85
Jams 91
Oil roller 85
OPC 85
See Status message
Transfer belt 85
Waste toner 85
Ethertalk 123
Extended accounting file size
message 88
Idle message 89
Image darkness sensor 75
ImageServer 112
Initializing
Status message 89
Installation
Accessories 101
BuzzBox 102
Duplex unit 107
Hard disk 127
Kanji font IDE hard disk 117
Lower feeder unit 101
Removing the transfer belt unit
fixture 30
Interface kit 123
Interfaces 159
DECnet interfaces 123
SCSI 125
F
J
Face, definition 7
Fonts 112
Fonts 114
ftp 113
Fuser
Replacement 19
Fuser oil empty message 89
Fuser oil roller 26
Replacement 26
Fuser unit and transfer roller 19
Jam recovery, automatic 53
Jams 67, 68
Media path 54
Preventing 52
Removing 55
Jaz drive 125
Job and subjob boundary, DOC 165
H
Hard disk 127
Header/trailer page, Document
Option Commands 163
HP PCL 5e
Document Option Commands 164
HP-GL
DOC 163
I
IDE hard disk 127
Idle
Status message 89
K
Kanji
Option kit 117
Software requirements 116
Kit 19
5-bin Mailbox 117
BuzzBox 102
DECnet interfaces 123
IDE hard disk 127
Kanji font internal IDE hard
disk 116
PlanetPress 122
QFORM 122
SCSI 125
169
Index
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
L
Labels
Continuous printing 38
Loading 37, 38
Printing 37, 38
LAN
Manager 123
Server 123
Laser lens cover 16
Lineprinter, DOC 164
LN03 112
LN03, DOC 166
Loading media 40
Lower feeder unit
Installation 101
Lower input feeder
Removing 148
M
Mailbox
Bin 120
Mailbox jam 90
Mailbox jam message 90
Maintenance
Paper exit rollers 50
Maximum performance 104
Media
Automatic jam recovery 53
Clearing media jams 55
Loading 40
Media path
5-bin mailbox 55
Duplex unit 55
Trays 55
Path 54
Preventing jams 52
Refilling cassette 40
Refilling multipurpose tray 40
Specifications 162
Tray 134
Tray fill limit mark 42, 45
Media jams 67, 68
Drum, inner, and outer jams 58
Inner, outer and drum jams 58
Lower right-side door 58
Outer, inner, and drum jams 58
Vertical transport area 58
Memory modules (DIMMs)
Dual in-line memory modules 103
Memory requirements 104
Memory, standard 105
Memory/Quick Config 105
MICR checks 122
Minimum system memory
requirements 104
Moving, printer 145
Replacement packaging 145, 149
Multipurpose tray (also known as
tray 1) 43
N
NetWare 123
Network interface
Installation 123
Using 125
O
OHP film 39
OPC drum cartridge 13, 29
Installing 17
Kit 7, 13
Removing 15
Replacing 17
Optional (lower feeder unit) tray 41
Ordering consumables 8
P
Packaging, printer
Replacement 145, 149
Page, definition 7
Paper
Jams 67, 68
Pass, definition 7
Path, media 54
Pause
Cooldown 87
Pause for AIDC 73
Physical specifications 162
Plane, definition 7
170
Index
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
PlanetPress 122
Plastic interlocks 149
Please wait message 88
PostScript
Forms 122
PostScript files 112, 114
Power requirements 155
ENERGY Star, compliance 157
Preventing paper jams 52
Print quality
All black sheet 77
Colors not correct 84
Faded on one side 75
Horizontal lines 75
Image blurred 77
Image comes off when rubbed 76
Irregular print 76
Lines on every page 83
Part of image missing 78
Print or color density uneven 76
Toner spots 79
Too dark 78
Too light 74, 75
Vertical lines 83
Printer
Handling 48
Level 75, 82
Lifting 49
Relocating 144
Repacking 145
Replacement packaging 145, 149
Resets 71
See also Specifications
Speed 157, 158
Storage 144
Storing 144
Printer stand/cabinet 135
Printing
Area 46
Envelopes 46
Labels 37, 38
Method 158
Speed 157, 158
Printing status message 92
Proof and print 163
Put x paper in any bin message 92
Put x paper in x bin message 92
Q
QFORM 122
Q-SHOP 8
R
Relocating your printer 144
Relocating, printer 145
Replacement packaging 145, 149
Repacking 145
Strapping/buckling instructions 151
Repacking, printer 145
Replacement packaging 145, 149
Replacement
Transfer belt 28
Replacement packaging 145, 149
Resets
Printer 71
Resetting accounting message 92
Resolution 105, 158
Return Merchandise Authorization
number 145
Returning, printer 145
RMA number 145
S
SC-210 convenience copier 101
Screen cover 119
SCSI 125
SCSI interface kit
Installation procedure 125
Service
Messages 85
Service messages 85
Shipping, printer 145
Replacement packaging 145, 149
RMA number 145
Simplex,definition 7
SIO 123
Slant 75, 82
Specifcations
Internal IDE hard disk 160
Specifications
CGM 159
Consumables 6
171
Index
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
Controller 157, 159
CPU 159
CrownNet Ethernet 159
Duty cycle 157
Emulations 159
Engine 157
Environmental 161
Flash ROM 160
Fonts 159
ImageServer 159
Input sources 158
Interfaces 159
Lineprinter 159
Media 162
Memory 160
Network interface 159
Optional emulations 159
Optional interfaces 159
Options 160
Output 158
Parallel 159
Physical 162
Print method 158
Print speed 157, 158
Resolution 158
SCSI interface 159
System software 160
Temperature 161
Toner 158
Toner cartridges 6
Warm-up time 158
Spooling performance increase 105
Static electricity discharge 101
Status message
Acc already disabled 86
Acc disabled 86
Acc enabled 86
Acc file x% full 86
Acc files got removed 86
Cancel all jobs 87
Cancel job 87
Check waste toner 87
Created files 88
Creating x file 88
End job 88
End job? 93
Extended accounting file size 88
Fuser oil roller
Fuser oil empty 89
Idle 89
Idle input printing 89
Initializing 89
Mailbox jam 90
Please wait 88
Printing status 92
Put x paper in any bin 92
Put x paper in x bin 92
Resetting accounting 92
Waiting for idle 92
Waiting on input end job? 93
Warming up 93
x Active jobs 85
Status messages 85
Strapping 151
System software
Specifications 160
T
TCP/IP 113, 123
Temperature requirements 161
Thick stock
Loading 36
Printing 36
Time-of-Day clock 135
Toner 158
Toner Cartridge
Storage 9
Toner cartridges 6
Transfer belt
Lowering 18
Raising to install OPC drum cartridge
15
Replacing 28
Transfer belt unit fixture 30
Transparencies 38
Continuous printing 39
Loading 38
Printing
OHP film 38
Tray 134
Lower feeder unit (Tray 5) tray 134
Multipurpose tray 43
Optional (lower feeder unit) 41
172
Index
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
Upper (also known as Standard)
(Tray 2) 134
Upper (standard) tray 2 41
Tray 1 43
Tray 2 41, 134
Troubleshooting
5-bin mailbox jams 66
Color looks wrong 84
Duplexing 73
Media jams 67, 68
Nothing is printed 74
Printer resets 71
Printer takes too much time 72
Status, service, and error
messages 85
U
UNIX 113
Upper (standard) tray 41
V
Ventilation grilles 156
W
Waiting for idle message 92
Waiting for idle status message 92
Waiting on input end job?
message 93
Warming up message 93
Warm-up time 158
Waste toner pack
Installing 19
Removing 13
Replacing 13, 19
Wrist strap for antistatic
protection 101
X
x Active jobs message 85
Z
Zip drive 125
173
Index
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement