Navigon 72xx GPS Receiver User Manual
User’s manual
NAVIGON 72xx
English (United Kingdom)
August 2008
The crossed-out wheeled bin means that within the European Union
the product must be taken to separate collection at the product end-oflife. This applies to your device but also to any enhancements marked
with this symbol. Do not dispose of these products as unsorted
municipal waste.
Imprint
NAVIGON AG
Schottmüllerstraße 20A
D-20251 Hamburg
The information contained herein may be changed at any time without prior
notification. Neither this manual nor any parts thereof may be reproduced for any
purpose whatsoever without the express written consent of NAVIGON AG, nor may
they be transmitted in any form either electronically or mechanically, including
photocopying and recording. All technical specifications, drawings etc are subject to
copyright law.
© 2008, NAVIGON AG
All rights reserved.
User’s manual NAVIGON 72xx
Table of contents
1
Introduction .......................................................................................6
1.1
About this manual.....................................................................................6
1.1.1
1.1.2
1.2
Legal notice ..............................................................................................6
1.2.1
1.2.2
1.3
2
Questions about the product ....................................................................7
2.1
Scope of Delivery .....................................................................................7
2.2
Description of the NAVIGON 72xx ...........................................................8
2.3
Important safety information.....................................................................8
2.4
2.5
Installing the navigation system in the vehicle...........................10
TMC antenna .............................................................................13
Memory card..............................................................................13
Navigating with GPS ..............................................................................14
Switching on the NAVIGON 72xx...................................................14
3.1
5
Navigation safety information ......................................................8
Safety information for the navigation device................................9
Safety guidelines when installing the device in your car ...........10
Preparing the NAVIGON 72xx for use....................................................10
2.4.1
2.4.2
2.4.3
4
Liability.........................................................................................6
Trademarks .................................................................................6
Before you begin...............................................................................7
2.3.1
2.3.2
2.3.3
3
Conventions.................................................................................6
Symbols .......................................................................................6
Options ...................................................................................................15
Password Lock................................................................................15
4.1
Activating password protection...............................................................15
4.2
Changing a password.............................................................................16
4.3
Cancelling password protection .............................................................16
4.4
Forgotten your password?......................................................................16
Operating the NAVIGON 72xx ........................................................16
5.1
Information .............................................................................................16
5.2
Software keyboard .................................................................................18
5.2.1
5.2.2
Special keys ..............................................................................19
Entering data .............................................................................20
5.3
Options ...................................................................................................20
5.4
Menus.....................................................................................................21
User’s manual
Table of contents Š III
User’s manual NAVIGON 72xx
6
Navigation .......................................................................................21
6.1
Starting the navigation application .........................................................21
6.2
Specifying a destination .........................................................................23
6.2.1
6.2.2
6.2.3
6.2.4
6.2.5
6.2.6
6.2.7
6.2.8
6.2.9
6.2.10
6.2.11
6.3
Managing destinations ...........................................................................32
6.3.1
6.3.2
6.4
Specifying the country in which the destination is situated........23
Entering a destination address ..................................................23
Selecting the destination address by voice command...............24
Points of interest........................................................................25
Information about the destination ..............................................28
Last Destinations .......................................................................29
Favourites ..................................................................................29
Imported addresses...................................................................30
Navigating home........................................................................30
Selecting destinations on the map.............................................31
Starting navigation.....................................................................31
Saving destinations ...................................................................33
Defining a destination as home address ...................................33
Multi-leg routes.......................................................................................33
6.4.1
6.4.2
6.4.3
6.4.4
6.4.5
6.4.6
6.4.7
Entering the starting point..........................................................34
Entering route points .................................................................34
Editing route points....................................................................35
Managing routes ........................................................................35
Calculating and displaying routes..............................................36
Simulating routes .......................................................................36
Starting navigation.....................................................................36
6.5
Options ...................................................................................................37
6.6
Working with the map.............................................................................39
6.6.1
6.6.2
6.6.3
6.6.4
6.6.5
6.7
Selecting the navigation map ....................................................39
Map in Preview mode ................................................................39
Map in Navigation mode............................................................41
Reality View PRO ......................................................................44
Map in Destination search mode ...............................................45
Useful functions......................................................................................46
6.7.1
6.7.2
6.7.3
6.7.4
6.7.5
6.7.6
Direct Help .................................................................................46
GPS Status, saving the current location....................................47
Block ..........................................................................................48
Turn-by-Turn List .......................................................................48
TMC (Traffic Information) ..........................................................50
Logbook .....................................................................................52
IV Š Table of contents
User’s manual
User’s manual NAVIGON 72xx
7
Handsfree Module...........................................................................53
7.1
Connecting to a telephone .....................................................................53
7.2
Taking a call ...........................................................................................54
7.3
Making a call ..........................................................................................54
7.3.1
7.3.2
7.3.3
7.3.4
7.3.5
7.4
During a call ...........................................................................................55
7.4.1
7.4.2
7.4.3
7.4.4
7.5
10
11
Preset ........................................................................................56
Handsfree Settings ....................................................................57
Bluetooth Function.....................................................................57
Connection with Mobile Phone...............................................................58
7.6.1
7.6.2
7.6.3
8
9
Moving the navigation application to the foreground .................56
Entering numbers ......................................................................56
Transferring a call to the mobile phone .....................................56
Ending the call ...........................................................................56
Configuring the hands-free function .......................................................56
7.5.1
7.5.2
7.5.3
7.6
Dialling a telephone number......................................................54
Dialling a Speed Call number ....................................................54
Calling a contact from the phone book ......................................55
Calling most recently dialled, received or missed numbers.......55
Transferring a call from your mobile telephone .........................55
Establishing a connection from the navigation device...............58
Establishing a connection from the mobile phone .....................59
Terminating the connection and deleting the connection
data............................................................................................59
Configuring the NAVIGON 72xx.....................................................60
Appendix .........................................................................................62
9.1
Technical data ........................................................................................62
9.2
Identification and serial number .............................................................63
9.3
Declaration of conformity........................................................................63
Troubleshooting..............................................................................63
Index ................................................................................................65
User’s manual
Table of contents Š V
User’s manual NAVIGON 72xx
1
Introduction
1.1
About this manual
1.1.1
Conventions
For better legibility and clarification, the following styles are used in this
manual:
Bold and italics:
Product names.
SMALL CAPITALS:
Window and dialogue box titles.
Bold:
Highlighting of important parts in the text.
Underlined:
Names of buttons, input boxes and other elements
on the user interface.
Underlined and italics:
Names of control elements on the navigation
device.
1.1.2
Symbols
The following symbols refer to specific passages of text:
Instructions and tips for operating the software
More detailed information and explanations
Warnings
1.2
Legal notice
1.2.1
Liability
The software and manual are subject to change without notice.
NAVIGON AG is not liable for the accuracy of the information contained
in this manual or for damages resulting from the use of this manual.
Suggestions for improvements and information regarding errors are
always welcome so that we can supply you with even better products in
the future.
1.2.2
Trademarks
All brand and trade marks mentioned in this document and registered
by third parties are subject without reservation to copyright law and the
-6-
Introduction
User’s manual NAVIGON 72xx
proprietary rights of their respective owners. All trade marks, trade
names and company names used in this document are or may be trade
marks or registered trademarks of their respective owners. All rights
reserved except those explicitly granted.
If the registered trademarks used in this manual are not explicitly
identified as such, this does not imply that the name is not subject to the
rights of a third party.
►
►
1.3
Microsoft, Outlook, Excel and Windows are registered trade marks
of the Microsoft Corporation.
NAVIGON is a registered trade mark of NAVIGON AG.
Questions about the product
You have a question concerning your product? Then visit our webseite
www.navigon.com and click on "Support". There you will find an area
with frequently asked questions (FAQ Center) along with details of how
to contact us by phone or e-mail.
2
Before you begin
2.1
Scope of Delivery
Please check that the contents are complete. If anything is missing, get
in touch immediately with the dealer who sold you the product.
The purchased product includes the following:
►
NAVIGON 72xx navigation device
►
Car cradle (in parts, refer to "Assembling the cradle" on page 11)
►
Car charger cable (10-24V adapter for the vehicle's cigarette lighter)
with integrated TMC antenna
►
USB cable
►
Leaflet with illustrated installation instructions
►
DVD with the following contents:
►
►
►
►
Before you begin
Manuals as PDF files
NAVIGON Fresh, with which you can keep your navigation
system up to date at all times and use additional services
NAVIGON Sync, with which you can transfer contact
addresses from Microsoft Outlook to your navigation system
Information about useful accessories
-7-
User’s manual NAVIGON 72xx
2.2
Description of the NAVIGON 72xx
1
2.3
Touch-screen
2
Slot for MicroSD memory card
3
Reset
4
LED
5
Mini USB socket for USB cable / car charger cable
6
Headset socket
7
Connection for external GPS antenna
8
Microphone
9
On/Off
Important safety information
In your own interest, please read the following safety information and
warnings carefully before starting up your navigation system.
2.3.1
Navigation safety information
Use the navigation system at your own risk.
Caution! To prevent accidents, do not operate the navigation system
while driving.
-8-
Before you begin
User’s manual NAVIGON 72xx
Caution! Do not look at the display unless it is absolutely safe to do so!
Caution! Traffic regulations have priority over any instructions from the
navigation system.
Caution! Follow the instructions of the navigation system only when the
circumstances and the road traffic regulations allow you to do so! The
navigation system will still guide you to your destination even if you
deviate from the calculated route.
Caution! Check that the cradle is secured and adjusted properly before
each journey.
Note: If you have not understood the spoken instructions or are unsure
about what to do next, you can refer briefly to the map or schematic
view of your navigation system.
2.3.2
Safety information for the navigation device
Caution! Protect the device from moisture. The device is neither
waterproof nor protected against splash water.
Caution! Do not open the case of the navigation device under any
circumstances.
Caution! Do not expose the navigation device to extreme heat or cold.
This may damage the device or impair its function. (Refer to "Technical
data" on page 62.)
Note: Do not kink the cable. Make sure that the cable cannot be
damaged by sharp-edged objects.
Note: Clean the navigation device only with a damp cloth.
Note: Do not unplug by pulling the cable. Doing so could damage the
cable!
Note: Create a backup of the data in the internal memory of your
navigation device. This is very easy to do with the NAVIGON Fresh
software which you will find on the enclosed DVD or can download free
of charge from our www.navigon.com.
1
Before you begin
-9-
User’s manual NAVIGON 72xx
2.3.3
Safety guidelines when installing the device in your car
Caution! Fasten the cradle so that the navigation device is easy to see
and operate by the driver. Make sure that the driver's view of the traffic
is not impeded.
Caution! Do not attach the cradle within the working zone of any
airbags.
Caution! Do not fasten the cradle too close to the steering wheel or
other controls. The driver must not be obstructed in operating any car
functions.
Caution! When installing the cradle, make sure that it will not pose a
risk in the event of an accident.
Caution! Do not run cables directly next to safety-relevant devices and
power supplies.
Caution! Check that the cradle is secured and adjusted properly before
each journey. The suction cup may become loose after a while.
Caution! After installation, check all safety-relevant equipment in the
car.
Caution! Connect the car charger cable only to cigarette lighters with
an operating voltage of 10-24V.
Caution! Disconnect the car charger cable from the cigarette lighter
whenever you park the car. The integrated mains adapter always
consumes a small amount of energy and could drain the car battery.
2.4
Preparing the NAVIGON 72xx for use
2.4.1
Installing the navigation system in the vehicle
Caution! Be sure to refer to all the safety information in chapter
"Important safety information" on page 8.
- 10 -
Before you begin
User’s manual NAVIGON 72xx
Assembling the cradle
►
Assemble the cradle as shown in the illustration. No tools are
needed for this.
Securing the cradle
1. Clean that part of the windscreen to which you want to secure the
cradle. The windscreen must be dry and free of dirt and grease.
2. Open the lever on the suction cup as far as possible.
3. Place the cradle suction cup against the windscreen.
4. Press the lever towards the windscreen.
Before you begin
- 11 -
User’s manual NAVIGON 72xx
Inserting the navigation device into the cradle
On the back of the NAVIGON 72xx you will see a circle with two
recesses.
1. Hang the navigation device by the upper recess on the upper lug of
the cradle. (See illustration)
2. Then press it towards the cradle so that it latches in place.
Supplying power to the navigation device
Included in delivery of the NAVIGON 72xx is a car charger cable with
which power can be supplied to the navigation device via the vehicle's
cigarette lighter.
►
Connect the car charger cable to the vehicle's cigarette lighter and
to the mini USB socket of the navigation device.
Note: Plug the USB connector into the navigation device swiftly as far it
will go! (Refer to "Troubleshooting" on page 63.)
Caution! Connect the car charger cable only to cigarette lighters with
an operating voltage of 10-24V.
The LED on the bottom of the navigation device lights up orange during
charging.
As soon as the battery is fully charged, the LED lights up green.
Note: It takes approx. 4-5 hours to charge the device when the battery
is flat.
A fully charged battery enables 3 hours of use.
Removing the navigation device from the cradle
On the bottom of the plate in which you hung the navigation device is a
clip.
- 12 -
Before you begin
User’s manual NAVIGON 72xx
1. Pull the clip towards yourself so that the device is released from the
clip.
2. Lift the device up and out of the cradle.
2.4.2
TMC antenna
The NAVIGON 72xx has an integrated TMC receiver. The TMC
antenna is integrated in the car charger cable. Once the car charger
cable is connected, the device can receive current traffic messages. If
required, it can change your route dynamically, e.g. in order to avoid a
traffic jam.
2.4.3
Memory card
A memory card with the software and card data is already inserted in
the navigation device.
You can copy these data to another memory card or save them on your
PC. Data backups, software updates and navigation map updates can
be carried out quickly and conveniently with NAVIGON Fresh, which
you will find on the enclosed DVD or can download free of charge from
the website www.navigon.com.
1
The following memory media can be used in the NAVIGON 72xx:
►
MicroSD cards
Removing the memory card
1. Switch off the navigation device. To do so, press the
key.
(On/Off)
2. Press the memory card gently into the device until the lock
disengages.
3. Let go of the memory card. It will now project slightly out of the
device.
4. Pull the memory card out of the slot.
Inserting a memory card
Before you begin
- 13 -
User’s manual NAVIGON 72xx
1. Insert the memory card into the device (see illustration).
2. Press the card into the device until it locks in place.
Note: The navigation application works only when the memory card
contains the navigation software and card data.
2.5
Navigating with GPS
GPS is based on a total of at least 24 satellites orbiting the Earth and
continuously transmitting signals of their position and time. The GPS
receiver receives this data and calculates its own geographical position
on the basis of the information transmitted by the various satellites.
Data from at least three satellites is required for positioning with an
acceptable degree of accuracy. With data from four or more satellites it
is possible in addition to determine the position's altitude above sea
level. Positioning is accurate to within three metres.
Once the navigation device has determined your position, this position
can be used as a starting point for calculating a route.
The map data on your navigation device includes the geographical
coordinates of all digitally recorded points of interest, streets and
places. This enables the device to calculate a route between a starting
point and a destination.
Calculation of the current position and its representation on the map
takes place once every second. In other words, your current position is
always shown on the map.
3
Switching on the NAVIGON 72xx
1. Press the
(On/Off) key and keep it pressed until the device
switches on. (Approx. 2 seconds)
If password protection has been activated, the ENTER PASSWORD
window opens.
2. Enter the password.
3. Tap on OK.
The NAVIGATION window opens.
Note: When you switch on the NAVIGON 72xx for the first time, you
will be asked to make the following settings:
- 14 -
►
your preferred language for using for the software
►
the unit of length for distances
►
the time format
Switching on the NAVIGON 72xx
User’s manual NAVIGON 72xx
Note: If you have not used the NAVIGON 72xx for a long time, the
battery may be flat.
In this case the device needs to be charged for approximately 3 minutes
before it can be switched on.
Forgotten your password?
If you forget your password, follow the procedure described in
"Forgotten your password?" on page 16.
Switching off the navigation device
►
Press the
(On/Off) key and keep it pressed until the device
switches off. (Approx. 2 seconds)
Note: If, when switching off the device, you press the
(On/Off) key
and keep it pressed for a long time (longer than approx. 6 seconds), the
device will perform a software restart the next time you switch it on.
Your settings and your saved destinations and routes will be retained.
3.1
Options
Some windows offer options that lead to more functions.
A description of all available options can be found in the chapter
"Options" on page 37.
4
Password Lock
You can protect your navigation system from unauthoriised use by
creating a password.
4.1
Activating password protection
1. In the NAVIGATION window tap on Options > Settings > Options >
Password Lock.
The NEW PASSWORD window opens.
2. Enter a password in the New password box and tap on Next.
3. Enter this password again in the Confirm new password box.
4. Tap on Activate.
Note: The password must have exactly 4 digits.
Password Lock
- 15 -
User’s manual NAVIGON 72xx
4.2
Changing a password
1. In the NAVIGATION window tap on Options > Settings > Options >
Password Lock.
The ENTER PASSWORD window opens.
2. Enter the currently valid password in the Enter password box.
3. Tap on Change password.
The NEW PASSWORD window opens.
4. Enter a password in the New password box and tap on Next.
5. Enter this password again in the Confirm new password box.
6. Tap on Activate.
Note: The new password must have exactly 4 digits.
4.3
Cancelling password protection
1. In the NAVIGATION window tap on Options > Settings > Options >
Password Lock.
The ENTER PASSWORD window opens.
2. Enter the currently valid password in the Enter password box.
3. Tap on Deactivate.
4.4
Forgotten your password?
If you enter the password wrongly three times, a window will open with
instructions telling you what to do now.
►
Follow the instructions on the screen.
5
Operating the NAVIGON 72xx
5.1
Information
Various information symbols are located at the top of many windows.
GPS
The GPS symbol can indicate the following GPS reception states:
No GPS (No symbol): The built-in GPS receiver is not operational.
Contact customer service if the problem persists.
No Signal: Data is being received from less than three satellites.
Position cannot be calculated.
- 16 -
Operating the NAVIGON 72xx
User’s manual NAVIGON 72xx
GPS Ready: Data is being received from at least three satellites.
Position can be calculated.
For details of the GPS status refer to chapter "GPS Status, saving the
current location" on page 47.
Compass
The Compass symbol indicates in which direction you are currently
heading. It can indicate the following points of the compass: N, NE, E,
SE, S, SW, W, NW..
TMC (Traffic Information)
The NAVIGON 72xx has an integrated TMC receiver which provides
the navigation system with traffic information updates. If necessary it
can change your route dynamically, for example in order to avoid a
traffic jam.
Note: This function is only available if TMC traffic messages are being
transmitted in the country in which you are travelling. This is not the
case in all countries.
The TMC symbol can display the following TMC reception status:
Tuning: The TMC receiver is operational but cannot find a station that
is transmitting TMC signals. There are no active traffic messages.
Tuning: The TMC receiver is operational but cannot find a station that
is transmitting TMC signals. Traffic messages are active however. This
can be the case, for example, when travelling through a tunnel.
TMC on Standby: Traffic messages can be received.
Note: The TMC antenna is integrated in the car charger cable. The
Tuning symbol may still appear therefore when the car charger cable is
not connected to the NAVIGON 72xx.
For details of the TMC function refer to chapter "TMC (Traffic
Information)" on page 50.
Energy
The Energy symbol can indicate the following states of the integrated
battery:
The device is being supplied by an external power source. The battery
is fully charged.
Operating the NAVIGON 72xx
- 17 -
User’s manual NAVIGON 72xx
The device is being supplied by an external power source. The battery
is being charged.
The device is being supplied by its internal battery. The battery charge
is sufficient.
The device is being supplied by its internal battery. The battery charge
is low.
Bluetooth / Phone
The NAVIGON 72xx has an integrated Bluetooth hands-free module.
This enables you to use the device as a hands-free kit for a mobile
phone with Bluetooth capability.
The Phone symbol can display the following states of the hands-free
module:
No Bluetooth (No symbol): The Bluetooth function is deactivated.
Not connected (red mobile phone): The NAVIGON 72xx has no
Bluetooth connection to another device.
Connected (white mobile phone): The NAVIGON 72xx is connected to
a mobile phone and can be used as a hands-free car kit.
Call in Progress (green mobile phone): The hands-free module of the
NAVIGON 72xx is being used for a phone call.
Muting
The Muting symbol can indicate the following states:
No symbol: The navigation application is not muted.
Muting: The navigation application is muted. If the device is navigating
at the moment, you will not hear any driving instructions.
Note: This symbol indicates only the muted state of the navigation
instructions. It says nothing about the volume of the hands-free module.
5.2
Software keyboard
A software keyboard appears on the screen when text entries are
necessary.
All entries can be made on the software keyboard using your fingertips.
Only capital letters can be entered.
When entering town or street names you need not enter any special
characters or umlauts. The navigation system fills in these characters
- 18 -
Operating the NAVIGON 72xx
User’s manual NAVIGON 72xx
for you automatically. For example, if you are looking for the town of
"Bärnau", then simply type in the word "BARNAU". Special characters
may be helpful however when naming saved destinations and routes.
5.2.1
Special keys
inserts a space.
deletes the character in front of the cursor.
opens the keyboard with numerals.
Latin, Cyrillic and Greek alphabet
opens the keyboard with the Latin alphabet.
opens the keyboard with the Cyrillic alphabet.
opens the keyboard with the Greek alphabet..
When you want to enter addresses, names or POIs, the keyboard with
the alphabet for the country in question will open automatically.
When you want to save a destination to Favourites or when you enter a
POI category or a country, the keyboard with the alphabet of the user
interface will open automatically.
You can also switch from the Cyrillic or Greek keyboard to the Latin
keyboard. Many addresses can then also be entered as transliterations
or in the language of the user interface.
Example: The language of the user interface is English. You want to
navigate to Moscow. You have the following options:
►
"Москва" (Cyrillic)
►
"Moskva" (transliterated)
►
"Moscow" (English).
Note: Street names and place names can be entered only in the
language of the user interface if that is how they exist in the map's
database.
Note: The maximum number of keyboards is always 2.
Operating the NAVIGON 72xx
- 19 -
User’s manual NAVIGON 72xx
Umlauts, accents and other letters
Another keyboard with special characters is available for each alphabet.
opens the keyboard with Latin special characters.
opens the keyboard with Cyrillic special characters.
opens the keyboard with Greek special characters.
As soon as you have entered a special character the letter keyboard
reappears.
5.2.2
Entering data
Often you can select an entry from a list. This is the case, for example,
when you enter a location.
As soon as you enter the first letter, the largest city in the given country
that begins with this letter appears.
Enter more letters and after each entry the first city which begins with
these letters will appear.
►
When the correct location appears, tap on
complete the entry.
(OK) in order to
You can open at any time a list containing all the locations which begin
with the letters or include the text already entered.
►
Tap on
(Open List) to call up this list.
(Up) button and the
You can use the
move through the list.
►
(Down) button to
Tap on an entry in the list to select it and transfer it to the input box.
The list closes once an entry has been selected.
►
Tap on
an entry.
(Close List) in order to close the list without selecting
Note: The list opens automatically as soon as it contains only 5 or less
entries.
5.3
Options
Some windows offer options that lead to more functions.
A description of all available options can be found in the chapter
"Options" on page 37.
- 20 -
Operating the NAVIGON 72xx
User’s manual NAVIGON 72xx
5.4
Menus
Some buttons have menus which open when activated.
►
Tap on a menu point to execute its function.
If you would like to quit the options list without selecting a function, tap
on the button you used to open the menu.
6
Navigation
Use the navigation system at your own risk.
Caution! Be sure to refer to all the safety information in chapter
"Important safety information" on page 8.
Impaired GPS reception
As soon as GPS reception is restored, the navigation system calculates
any change of position which has occurred in the meantime. You can
then simply continue navigating.
Arriving at your destination
When you have reached your selected destination, a message to this
effect will be displayed.
Only your current position (orange arrow) will now be shown on the
map.
6.1
Starting the navigation application
You have switched on the navigation device and, if necessary, entered
the password.
The following message appears:
"The navigation software on this device is designed to provide route
suggestions and does not replace the need for driver attentiveness or
the requirement to adhere to road traffic regulations, good driving
practice and legally posted directions. For safety, posted road signs
and directions should always take precedence over the directions of this
unit. Do not operate this unit while driving."
►
After you have read and fully understood the message, tap on OK.
If you do not accept the content of the message, tap on Cancel in
order to switch the navigation device off again.
Navigation
- 21 -
User’s manual NAVIGON 72xx
The NAVIGATION window is opened. From here you can access all the
functions of the navigation application.
►
►
Tap on
(Phone) in order to move the hands-free module
into the foreground.
Tap on
(Navigation) in order to move the NAVIGATION
window back into the foreground.
Initialising the GPS receiver
As soon as the navigation device has been switched on, initialisation of
the GPS receiver will begin.
The integrated GPS receiver is not initialised for the first time until the
navigation application is started for the first time. It can take up to
20 minutes to initialise the GPS receiver for the first time.
Note: If the GPS symbol indicates GPS Ready after far less than
20 minutes, it is advisable to leave the navigation device switched on
for at least another 15 minutes in order to ensure reliable operation of
the receiver.
Each time you switch on the navigation device after this, GPS reception
will start within a short time.
If the navigation device has not been switched on for more than a week,
it can take up to 10 minutes to re-initialise the receiver.
In the top right hand corner of the display, you will see the GPS symbol.
As soon as data from at least three satellites is received, the icon will
change to
(GPS Ready).
Note: Initialisation takes the least time if you do not start driving until
the initialisation has finished.
For more details about the GPS symbol refer to chapter "GPS" on
page 16.
Returning to the Navigation window
The NAVIGATION window opens when the navigation application is
started.
If another window of the navigation application is open, tap on
(Back). This will return you to the window you came from.
►
- 22 -
Tap on
opened.
(Back) repeatedly until the NAVIGATION window is
Navigation
User’s manual NAVIGON 72xx
6.2
Specifying a destination
Under New Destination you can enter destinations to which you have
not yet navigated or which you have not saved.
You can enter an address here, select a POI, or select a destination
from the quick search function.
Note: The first time that you want to enter a new destination you will be
asked to select the country in which your destination is situated.
Under My Destinations the NAVIGON 72xx provides the following lists
of destinations and addresses for you to select from:
►
►
►
6.2.1
LAST DESTINATIONS: Destinations to which you have navigated on a
previous occasion.
FAVOURITES: All destinations that you have entered in the
NAVIGON 72xx and then saved.
IMPORTED ADDRESSES: All destinations that you have imported from
Microsoft Outlook or from other data sources.
Specifying the country in which the destination is situated
At top left in the ADDRESS, POI IN A CITY and POI NATIONWIDE windows
you will find the Country button. It bears the flag of the country in which
you can currently select destinations for the navigation application.
If your destination is in a different country, then proceed as follows:
1. Tap on the Country button.
2. Enter the first letter of the country in which your destination is
situated.
The COVERED COUNTRIES list opens. It shows all the countries
which begin with this letter and for which a map is available.
3. Tap on the country in which your destination lies.
The COVERED COUNTRIES list closes.
The button bears the flag of the destination country.
Note: The selection list contains only those countries whose maps are
available to the navigation device.
6.2.2
Entering a destination address
1. In the NAVIGATION window, tap on New Destination > Enter an
Address.
The ADDRESS window opens.
2. Enter the name or the postal code of the destination town.
3. Enter the name of the destination street.
Navigation
- 23 -
User’s manual NAVIGON 72xx
4. Enter the house number. If you do not know the house number,
then leave this box empty.
If you don't know the house number but know the name of a nearby
side street, then tap on the Cross Street box and enter the name of
this street. The navigation system will calculate a route to the
intersection of the streets you have entered.
Note: It is not necessary to enter all the address details.
If you specify the town only, the navigation system will calculate a route
to the town centre.
If you specify only the town and street without specifying a house
number or cross street, the navigation system will calculate the best
route to this street.
5. Tap on Start Navigation.
Sometimes the destination cannot be found exactly because, for
example, the entered combination of place and street name exists
several times.
In this case a window will open with a list of all the addresses
matching your entry plus additional information.
►
Tap on the address to which you want to navigate.
If the entered house number is not included on the map, the window
will show an address with the house number closest to the one
entered.
►
Tap on OK in order to navigate to this address.
The map opens in Preview mode. The destination is indicated on
the map.
For detailed information on how to start navigation, please refer to
chapter "Starting navigation" on page 31. Please read on there.
6.2.3
Selecting the destination address by voice command
It is particularly convenient to select the destination address by voice
command.
1. In the Voice Command window, tap on NAVIGATION.
The VOICE COMMAND window opens.
Indicated at the top is the country from which you can select
addresses.
►
Tap on the country if your destination address is situated in a
different country. Then follow the instructions given by the
navigation system.
You will be asked for the address data in this order: City > Street >
House number.
- 24 -
Navigation
User’s manual NAVIGON 72xx
2. Follow the instructions given by the navigation system.
When you have finished entering the address, the map will open in
Preview mode. The destination is indicated on the map.
For detailed information on how to start navigation, please refer to
chapter "Starting navigation" on page 31. Please read on there.
Note: The Voice Command function is not available for every
language. In the languages for which this function is not available, the
Voice Command button is replaced by the Show Map button.
6.2.4
Points of interest
Points of Interest, also called POI (Points Of Interest) for short, are
useful addresses that are catalogued according to particular criteria.
POIs include ports, airports, restaurants, hotels, petrol stations, public
buildings, doctor's surgeries, hospitals, shopping centres, etc.
Points of interest can be displayed on the map by means of a symbol.
In the NAVIGATION window tap on Options > Settings > Map Display >
Categories Shown in order to select the categories you want to appear
on the map.
POI nearby
POIs nearby are POIs located within a certain radius of your current
location. This means you can always find the nearest petrol station for
example, no matter where you are.
Note: GPS reception must be good enough for determining your
(GPS Ready) symbol to see whether GPS
position. Check the
reception is good enough.
For more details refer to chapter "Initialising the GPS receiver" on
page 22.
Note: The Direct Access section offers 3 categories of POI from the
current vicinity which can be searched for quickly and without additional
entry.
For more details refer to chapter "Direct access to POI" on page 28.
1. Tap in the NAVIGATION window on New Destination > Search for
POI > Nearby.
The POI NEARBY window opens.
2. Select a category from which you would like to find a POI.
Categories in which no destinations are available nearby cannot be
selected.
Navigation
- 25 -
User’s manual NAVIGON 72xx
If sub-categories exist for the category you have selected, the Sub
Category list opens.
3. Select the sub-category from which you would like to select a POI.
The Name of the Destination list opens. It contains the nearest POI
in the specified category, sorted by distance.
4. Tap on the name of the destination.
Instead of the keyboard you are shown information about this POI
from the database. (Refer to "Information about the destination" on
page 28)
5. Tap on Start Navigation.
The map opens in Preview mode. The destination is indicated on
the map.
For detailed information on how to start navigation, please refer to
chapter "Starting navigation" on page 31. Please read on there.
POI of nationwide significance
POIs of nationwide significance are airports, sights, national
monuments, large ports etc. This way you can find well-known places of
interest even if you don't know the name of their location.
1. In the NAVIGATION window, tap on New Destination > Search for
POI > Nationwide.
The POI NATIONWIDE window opens.
2. Select a category from which you would like to find a POI.
The Name of the Destination list opens. It contains the POI from the
selected category, sorted alphabetically.
3. If the list is very long:
►
Tap on
(Close List)
The keyboard appears.
►
►
Enter a number of letters from the destination.
Tap on
(Open List)
The list now contains only those destinations which begin with or
contain the letters entered.
4. Tap on the name of the destination.
Instead of the keyboard you are shown information about this POI
from the database. (Refer to "Information about the destination" on
page 28)
5. Tap on Start Navigation.
- 26 -
Navigation
User’s manual NAVIGON 72xx
The map opens in Preview mode. The destination is indicated on
the map.
For detailed information on how to start navigation, please refer to
chapter "Starting navigation" on page 31. Please read on there.
POI in a particular location
POIs in a particular location can be useful when navigating in an
unfamiliar town.
1. In the NAVIGATION window, tap on New Destination > Search for
POI > in a City.
The POI IN A CITY window opens.
2. Enter the name or the postal code of the destination town.
3. Select a category from which you would like to find a POI.
Categories in which no destinations are available in the selected
town cannot be entered.
If sub-categories exist for the category you have selected, the Sub
Category list opens.
4. Select the sub-category from which you would like to select a POI.
The Name of the Destination list opens. It contains POI from the
specified category, sorted alphabetically.
5. If the list is very long:
►
Tap on
(Close List)
The keyboard appears.
►
►
Enter a number of letters from the destination.
Tap on
(Open List)
The list now contains only those destinations which begin with or
contain the letters entered.
6. Tap on the name of the destination.
Instead of the keyboard you are shown information about this POI
from the database. (Refer to "Information about the destination" on
page 28)
7. Tap on Start Navigation.
Sometimes the destination cannot be found exactly because, for
example, several restaurants with the same name exist in the town
in question.
In this case a window opens with all the destinations matching your
entry plus additional information.
►
Navigation
Tap on the destination to which you would like to navigate.
- 27 -
User’s manual NAVIGON 72xx
The map opens in Preview mode. The destination is indicated on
the map.
For detailed information on how to start navigation, please refer to
chapter "Starting navigation" on page 31. Please read on there.
Direct access to POI
The direct access area contains categories of POI. Destinations in your
vicinity that correspond to one of these categories can be viewed here
quickly and without further entry.
►
Tap in the NAVIGATION window on Options > Settings > General in
order to select the categories for direct access.
Note: The categories for the Direct Access function are the same as
those available for the POI on Your Route function. (Refer to
"Functions of the map in Navigation mode" on page 43)
Note: GPS reception must be good enough for determining your
position. Check the
(GPS Ready) symbol to see whether GPS
reception is good enough.
For more details refer to chapter "Initialising the GPS receiver" on
page 22.
1. In the New Destination window, tap on NAVIGATION.
The NEW DESTINATION menu opens.
In the Direct Access area you are shown the symbols of those POI
categories that are available by direct access.
2. Tap on the category from which you would like to select a POI.
The Name of the Destination list opens. It contains the nearest POI
in the specified category, sorted by distance.
3. Tap on the name of the destination.
The map opens in Preview mode. The destination is indicated on
the map.
For detailed information on how to start navigation, please refer to
chapter "Starting navigation" on page 31. Please read on there.
6.2.5
Information about the destination
For many destinations that you specify, there will be further information
available, stored in the navigation system's database.
There is, for example, a telephone number available for many
restaurants. You can then call the restaurant to reserve a table, for
example.
- 28 -
Navigation
User’s manual NAVIGON 72xx
One of the destination entry windows described above is open.
►
Tap on Options > Info.
The DESTINATION INFO window opens. It contains all the information
about the specified destination that is stored in the navigation system's
database.
►
►
►
Tap on Cancel in order to close the DESTINATION INFO window
again.
Tap on
map.
(Show on Map) in order to see the destination on the
Tap on
(Call) in order to call the number indicated.
Note: The Call function is only available when the NAVIGON 72xx is
connected via Bluetooth to a mobile phone.
For details of how to connect to a mobile phone refer to chapter
"Connecting to a telephone" on page 53.
6.2.6
Last Destinations
NAVIGON 72xx saves the last 12 destinations to which you have
navigated in the LAST DESTINATIONS list.
1. In the NAVIGATION window, tap on My Destinations > Last
Destinations.
2. Tap on the destination to which you would like to navigate.
3. Tap on Start Navigation.
The map opens in Preview mode. The destination is indicated on
the map.
For detailed information on how to start navigation, please refer to
chapter "Starting navigation" on page 31. Please read on there.
6.2.7
Favourites
Destinations to which you want to travel often can be saved in the
FAVOURITES list.
In the FAVOURITES list you can save up to 500 destinations.
Information on how to save a destination can be found in chapter
"Saving destinations" on page 33.
1. In the NAVIGATION window, tap on My Destinations > Favourites.
2. Tap on the destination to which you would like to navigate.
3. Tap on Start Navigation.
Navigation
- 29 -
User’s manual NAVIGON 72xx
The map opens in Preview mode. The destination is indicated on
the map.
For detailed information on how to start navigation, please refer to
chapter "Starting navigation" on page 31. Please read on there.
Note: Favourites are indicated on the map by a small flag with their
name. At Options > Settings > Map Display > Categories Shown you
can switch on and off the display function for favourites.
6.2.8
Imported addresses
You can use the NAVIGON Sync software to export to your navigation
system the contact addresses which you have saved in Microsoft
Outlook on your computer.
From many route planners on the Internet it is also possible to copy the
entered destination address directly onto your navigation system. This
function is clearly indicated on those websites which offer it.
Note: The NAVIGON Sync software is on the enclosed DVD.
Contacts which have been saved with several addresses will appear
once with each address in the IMPORTED ADDRESSES list.
1. In the NAVIGATION window, tap on My Destinations > Imported
addresses.
2. Tap on the address to which you want to navigate.
3. Tap on Start Navigation.
The map opens in Preview mode. The destination is indicated on
the map.
For detailed information on how to start navigation, please refer to
chapter "Starting navigation" on page 31. Please read on there.
6.2.9
Navigating home
In NAVIGON 72xx you can save an address as your home address.
You can navigate to your home address at any time by pressing a
single button.
Further information about entering your home address can be found in
chapter "Defining a destination as home address" on page 33.
►
In the Take Me Home window, tap on NAVIGATION.
If you have not yet entered your home address, a dialog box will
notify you of this.
- 30 -
Navigation
User’s manual NAVIGON 72xx
Navigation starts. The route profile used for the previous navigation will
be applied.
6.2.10
Selecting destinations on the map
You may select a destination directly on the map. This is a quick way to
select towns, streets and POI.
1. In the Show Map window, tap on NAVIGATION.
If the Voice Command button is available in the NAVIGATION
window, tap on Options > Show Map.
2. Tap on
(Destination search)
The map opens in Destination search mode.
3. Tap on the point to which you want to navigate.
Note: For details of how to change the map view so that your
destination is easily seen refer to the chapter "Map in Destination
search mode" on page 45.
The destination that you have selected appears under the cross
hairs.
The geographical coordinates of the destination and the
corresponding address are shown in the bottom third of the screen.
4. Tap on
(OK)
The DESTINATION ON MAP window opens. The detailed address data
of the selected destination is displayed in the upper left-hand
corner.
5. Tap Take Me There.
The map opens in Preview mode. The destination is indicated on
the map.
For detailed information on how to start navigation, please refer to
chapter "Starting navigation" on page 31. Please read on there.
6.2.11
Starting navigation
The map is open in Preview mode.
The navigation destination is depicted by a small flag. The route and the
estimated time of arrival are indicated.
►
Tap on the arrival time if you want to see the estimated driving time
instead.
Route Profile
The route is calculated on the basis of a route profile.
Navigation
- 31 -
User’s manual NAVIGON 72xx
►
If you want to view or change the route profile, tap Route Profile.
Note: If you change the route profile, the changes will also apply to
future navigations.
Information about individual route profile settings can be obtained by
tapping the related
(Help) button.
Turn-by-Turn List
►
If you want to see detailed directions for the route, tap on Options >
Turn-by-Turn List.
For details of the functions in the TURN-BY-TURN LIST window refer to
chapter "Turn-by-Turn List" on page 48.
Start Navigation
►
Tap on Start Navigation or simply start driving.
No GPS reception
If GPS signal reception is not good enough, the following message will
appear: "GPS reception is currently not sufficient. Navigation starts
automatically as soon as GPS reception is OK again."
You have the following options:
►
►
►
Wait. As soon as GPS reception is good enough for determining
your position, the route will be recalculated and navigation will
begin.
Tap Cancel. The window in which you entered your destination will
open again. Your destination is saved in the LAST DESTINATIONS list.
Tap Demo. The route will be calculated using the centre of the
destination location as starting point. Navigation will then be
simulated on this route.
Tap on
(Back) in order to terminate the demonstration.
Note: If you selected the destination on the map, then the Demo button
is not available.
6.3
Managing destinations
Every destination you enter and destinations from the LAST
DESTINATIONS and IMPORTED ADDRESSES lists can be saved in the
FAVOURITES list. This makes sense if you frequently navigate to a
particular destination.
- 32 -
Navigation
User’s manual NAVIGON 72xx
Note: Favourites are indicated on the map by a small flag with their
name. At Options > Settings > Map Display > Categories Shown you
can switch on and off the display function for favourites.
6.3.1
Saving destinations
1. Enter a destination. (Refer to "Entering a destination address " on
page 23 or "Points of interest" on page 25). Do not tap on the Start
Navigation button!
2. Tap on Options > Save Destination.
- OR –
1. Select a destination from the LAST DESTINATIONS list or from the
IMPORTED ADDRESSES list. (Refer to "Last Destinations" on page 29
or "Imported addresses" on page 30). Do not tap on the Start
Navigation button!
2. Tap on Options > Save as Favourite.
3. Enter a name for the destination.
4. Tap on Save.
6.3.2
Defining a destination as home address
One destination from the FAVOURITES list can be defined as your home
address.
You can then always start navigation to this destination very quickly by
tapping in the NAVIGATION window on Take Me Home.
1. Select the destination which you want to define as your home
address from the FAVOURITES list. (Refer to "Favourites" on
page 29.)
2. Tap on Options > Home Address.
The selected destination has now been saved as your home address.
Your home address now appears in the FAVOURITES list marked by a
house symbol.
6.4
Multi-leg routes
It is possible to plan routes without GPS reception, for example in the
comfort of your home. Planned routes can be saved for later use. This
allows you to plan as many routes as you like, for example for your
holidays.
1. In the Options window, tap on NAVIGATION.
The options list opens.
2. Tap on the Route Planning option.
The ROUTE PLANNING window opens.
Navigation
- 33 -
User’s manual NAVIGON 72xx
6.4.1
Entering the starting point
The starting point of a route is the point at which you want to begin your
trip. This is not necessarily the current location. If you are planning a
route for your holidays at home, you could, for example, enter your
hotel as the starting point.
The starting point is only important if you want to see a planned route
on the map but currently have no GPS reception, or if you are not
currently at the planned starting point. This is why your selected starting
point has the flow number "0".
As soon as you start navigation, your current location will be used as
the starting point for the route calculation.
The first leg of the route is therefore the journey to the route point with
flow number "1".
1. Tap on the Specify Starting Point box.
The STARTING POINT menu opens.
If you want to enter your current location as the starting point:
2. Tap on the Current Position menu item.
If you want to enter a different starting point:
2. Tap on the corresponding button.
3. Enter the starting point. (Refer to the corresponding section of the
chapter "Specifying a destination" on page 23 ff.)
4. Tap on Set Starting Point.
The selected starting point will now be displayed next to the 0
button (Starting Point).
Changing the starting point
►
Tap on the starting point (button 0).
The STARTING POINT menu opens. You can now enter a different
starting point. Proceed as described above.
6.4.2
Entering route points
The route points of a route are the destinations that you want to
navigate to.
The flow number for each route point is indicated on a button in front of
it.
1. Tap on the Add Route Point box.
The ROUTE POINT menu opens.
2. Tap on the button for how you want to enter the destination.
3. Enter the route point. (Refer to the corresponding section of chapter
"Specifying a destination" on page 23 ff.)
- 34 -
Navigation
User’s manual NAVIGON 72xx
4. Tap on Add.
The selected route point is now shown next to its flow number.
Repeat these steps for each destination that you want to add to your
route.
6.4.3
Editing route points
Route points can be deleted from a route. The order of the route points
can be changed as you wish.
Note: The starting point (flow number "0") can be neither moved nor
deleted. However you can make another route point into the starting
point.
►
Tap on the route point that you want to edit.
The context menu contains the following buttons:
Route Point Up: Moves the selected route point further to the front.
(Example: route point 2 becomes route point 1)
Route Point Down: Moves the selected route point further to the
back. (Example: route point 2 becomes route point 3).
Delete: Deletes the selected route point. A dialog window prompts
you to confirm deletion.
6.4.4
Managing routes
You can save each planned route under a particular name.
Note: Only the start point and route points will be saved, not the
calculated route. When you load a saved route, it must be recalculated
before navigation can start.
You can load, rename or delete stored routes.
Saving routes
The ROUTE PLANNING window is open. You have entered the starting
point and at least one route point.
1. Tap on Options > Save Route.
2. Enter a name for the route.
3. Tap on Save.
The destination is now saved to the SAVED ROUTES list. The dialog
window closes.
Navigation
- 35 -
User’s manual NAVIGON 72xx
Loading routes
1. Tap on Options > Saved Routes.
2. Tap on the route that you want to load.
3. Tap on Load Route.
The ROUTE PLANNING window opens. The starting point and the
route points of the loaded route have been entered.
6.4.5
Calculating and displaying routes
It is possible to calculate and display a planned route on the map even
without GPS reception in order to get an impression of the journey.
The ROUTE PLANNING window is open. The starting point and at least
one route point have been entered.
►
Tap on Show Route.
The map opens in Preview mode.
The starting point and the route points are marked by flags. The
distance and the estimated trip time is given for each leg of the
route. The route and the estimated time of arrival are displayed for
the complete route.
►
6.4.6
Tap on the arrival time if you want to see the estimated driving time
instead.
Simulating routes
It is also possible simply to simulate navigation on a planned route.
Note: GPS reception is not necessary for simulation.
If you have planned a multi-leg route, only the first leg will be simulated.
You have calculated and displayed a route.
►
Tap on Options > Simulation.
The route will be recalculated for simulation purposes. Simulation
starts when calculation has finished.
Stopping simulation
You can stop simulation at any time.
►
Tap on
(Back)
The ROUTE PLANNING window opens.
6.4.7
Starting navigation
You have calculated and displayed a route.
- 36 -
Navigation
User’s manual NAVIGON 72xx
Route Profile
The route is calculated on the basis of a route profile.
If you want to view or change the route profile, tap on Route Profile.
Note: If you change the route profile, the changes will also apply to
future navigations.
Information about individual route profile settings can be obtained by
tapping on the related
(Help) button.
Note: When you load routes which originate from a different provider
than NAVIGON, the Route Profile button may be inactive. You cannot
change the route profile of this route.
Turn-by-Turn List
If you want to see detailed directions for the route, tap on Options >
Turn-by-Turn List.
For details of the functions in the TURN-BY-TURN LIST window refer to
chapter "Turn-by-Turn List" on page 48.
Start Navigation
►
Tap on Start Navigation.
No GPS reception
If GPS signal reception is not good enough, the following message will
appear: "GPS reception is currently not sufficient. Navigation starts
automatically as soon as GPS reception is OK again."
You have the following options:
►
►
6.5
Wait. As soon as GPS reception is good enough for determining
your position, the route will be recalculated and navigation will
begin.
Tap on Cancel. The map opens in Preview mode.
Options
Some windows offer options that lead to more functions.
►
Tap on Options to open the options list.
►
Tap on the option you would like to use.
►
Navigation
If you would like to quit the options list without selecting an option,
tap on the Options button again.
- 37 -
User’s manual NAVIGON 72xx
Add to Route: Opens the route planning. The selected address will be entered
as the starting point of a new route. (Refer to "Multi-leg routes" on
page 33.)
Delete All: Deletes all destinations in the list (LAST DESTINATIONS list or
FAVOURITES list, depending on where you opened the options). The list
is then empty. A dialog window prompts you to confirm deletion.
Delete: Deletes the selected destination from the LAST DESTINATIONS or
FAVOURITES list or the selected route from the SAVED ROUTES list. A
dialog window prompts you to confirm deletion.
Direct Help: Opens a window in which you can find in quick and uncomplicated
manner the addresses and phone numbers of offices in your direct
vicinity that can be useful in emergencies. (Refer to "Direct Help" on
page 46)
Factory Settings: Resets all settings to the as-delivered state. Routes and
saved destinations will be deleted. The software is re-started and
behaves as if started for the first time after being purchased. (Refer to
"Switching on the NAVIGON 72xx" on page 14.)
GPS Status: Opens the GPS STATUS window. Here you can see details
regarding GPS reception. You can also save the data of your current
location. (Refer to "GPS Status, saving the current location" on
page 47.)
Home Address: Saves the selected destination as your home address. You can
then always start navigation to this destination very quickly by tapping in
the NAVIGATION window on Take Me Home.
New Route: Deletes the starting point and all route points from the ROUTE
PLANNING window so that you can plan a new route.
If necessary, save the previously planned route!
Password Lock: Opens a window in which the password can be configured.
(Refer to "Password Lock" on page 15)
Product Information: Here you are shown the version numbers and copyright
details of the hardware and software.
Rename: Opens a window in which you can change the name for the selected
destination or route.
Route Planning: Opens the ROUTE PLANNING window. Here you can plan
routes, manage planned routes and start navigation on a planned route.
(Refer to "Multi-leg routes" on page 33.)
Route Profile: Opens the ROUTE PROFILE window. Here you can view the
options for route planning and, if necessary, change them.
- 38 -
Navigation
User’s manual NAVIGON 72xx
Save as Favourite: Saves the selected destination to the FAVOURITES list. (Refer
to "Saving destinations" on page 33.)
Save Destination: Saves the selected address in the FAVOURITES list. (Refer to
"Saving destinations" on page 33.)
Save Route: Opens a window in which you can save the planned route under a
specific name. (Refer to "Saving routes" on page 35.)
Saved Routes: Opens a dialog window into which you can load a saved route.
Settings: Opens the SETTINGS window. Here you can configure the navigation
system. (Refer to "Configuring the NAVIGON 72xx" on page 52.)
Show on Map: Shows the selected address on the map.
Simulation: Simulates a navigation on the route indicated. This simulation can
be performed without GPS reception. On multi-leg routes, only the first
leg is simulated.
Touchscreen Calibration: The touchscreen can be re-calibrated if it responds
poorly to touch. Follow the instructions on the screen.
Traffic: Opens the TRAFFIC INFORMATION window in which pending reports are
listed. (Refer to "TMC (Traffic Information)" on page 50.)
Turn-by-Turn List: Shows detailed directions for the route, including all points at
which you must turn. (Refer to "Turn-by-Turn List" on page 48.)
6.6
Working with the map
6.6.1
Selecting the navigation map
Each country has its own navigation map. However, seamless
navigation over several maps on one continent is possible if a
continuous route can be planned on the maps saved.
Even if maps from several continents are saved on the memory card in
your navigation device, the NAVIGON 72xx can only ever work with
maps from one continent.
Tap in the NAVIGATION window on Options > Settings > Map Display >
Countries in to see which maps are currently in use. Here you can also
select a different continent if the navigation device contains any maps of
countries on other continents.
6.6.2
Map in Preview mode
You have entered a destination and tapped on Start Navigation.
- OR –
Navigation
- 39 -
User’s manual NAVIGON 72xx
You have planned or loaded a route and tapped on Show Route.
The map opens in Preview mode. The entire route is visible.
1
2
The route is marked in orange.
Your current position is indicated ().
If you display a planned or loaded route and the specified starting point
is not your current location, then it is possible that your current position
will not be shown on the preview.
3
The destination is marked with a little flag.
If you display a planned or loaded route, the starting point and each
route point will be marked with a little flag.
4
In a small info box you can see the complete route and the estimated
time of arrival.
►
►
Tap on the arrival time if you want to see the estimated driving time
instead.
Tap once again on the info box if you want to see the estimated
time of arrival.
The display for this information can be configured via Options >
Settings > Navigation.
If you display a multi-leg route, the route and the estimated driving time
for each leg will be displayed. The information for the various legs
cannot be configured.
►
►
Tap on Route Profile in order to view and, if required, change the
settings which form the basis for the route planning.
Tap on Start Navigation to start the trip.
If you display a planned or loaded route, the route may be
recalculated. The starting point for the calculation will now be your
current location. You will first be guided to the first route point
entered.
- 40 -
Navigation
User’s manual NAVIGON 72xx
►
►
6.6.3
Tap on Options > Turn-by-Turn List to view detailed directions for
the route. (Refer to "Turn-by-Turn List" on page 48)
Tap on
(Destination search) in order to view the map in
Destination search mode. (Refer to "Map in Destination search
mode” page 45)
Map in Navigation mode
After the route was shown in Preview mode, navigation was started.
The map opens in Navigation mode.
1
Here is shown what signposts should be followed.
2
Possible speed limits may be shown here.
3
The route is highlighted in orange.
4
When two manoeuvres need to be executed in quick succession, the
small arrow box indicates the second manoeuvre to be executed.
5
The large arrow box shows a diagram of the next junction which you
should turn on to. The distance remaining to this junction is indicated
underneath.
As you get closer to the junction you will see a spot diagram in addition
to the distance:
The nearer you get to the junction, the more yellow spots are displayed.
If you don't have to change direction for a long time, you will see only a
straight arrow. The distance you must continue straight on is indicated
underneath the arrow.
►
Navigation
Tap on the large arrow box to hear current route instructions.
- 41 -
User’s manual NAVIGON 72xx
6
The Traffic Information box opens if a reported traffic obstruction
affects your route.
If a distance is indicated in the Traffic Information box, no detour route
was calculated yet for the traffic obstruction in question.
►
Tap on the Traffic Information box in order to see the complete
message. You can then decide whether a detour route is to be
calculated (Detour) or not (Ignore).
If no distance is indicated, all the obstructions which are reported for
your route and would lead to a loss of time will be avoided.
►
Tap on the Traffic Information box in order to view all the traffic
obstructions reported for your route. (Refer to "TMC (Traffic
Information)" on page 50)
Note: The calculation of detour routes to avoid reported traffic
obstructions can be performed automatically. (Refer to "TMC Settings"
on page 51)
7
Ahead of many junctions the information from points 8 and 9 is hidden.
Instead you are shown which lanes lead to your destination.
►
Tap on the box in order to hide the lane information.
8
The height above sea level and the current speed are shown here.
9
In the Total box you can see the distance remaining to the destination,
the estimated duration of the trip and the estimated time of arrival.
►
►
Tap on the arrival time if you want to see the estimated driving time
instead.
Tap once again on the info box if you want to see the estimated
time of arrival.
10
Your current position is indicated on the map (orange arrow). The
section of the map displayed changes continually so that your current
position is always in view on the map.
11
If you are navigating a multi-leg route, you will see the remaining
distance to the next interim destination and the estimated time of arrival
in the Next box.
►
►
Tap on the arrival time if you want to see the estimated driving time
instead.
Tap once again on the info box if you want to see the estimated
time of arrival.
12
The name of the route section that you need to drive onto next is shown
in the upper road box.
13
The name of the section you are currently driving on is shown in the
lower road box.
Note: The displays of many of the above mentioned areas can be
configured in Options > Settings > Navigation. Some displays will only
function if the required information is available on the map..
- 42 -
Navigation
User’s manual NAVIGON 72xx
Note: If you tap on the large arrow box, the current route instruction will
be repeated.
►
►
Tap on Options > Turn-by-Turn List to view detailed directions for
the route. (Refer to "Turn-by-Turn List" on page 48.)
Tap on
(Destination search) in order to view the map in
Destination search mode. (Refer to "Map in Destination search
mode" on page 45.)
Volume
The volume of the spoken driving instructions can be adjusted during
navigation.
1. Tap on
(Volume).
The volume bar opens. It contains three buttons for adjusting the
volume.
(Louder),
2. Tap on
(Quieter),
(Volume on/off).
(Volume) again or wait a few seconds.
The volume bar closes.
Quitting navigation
Tap on
(Back) in order to quit navigation. A dialog box will
prompt you to confirm.
Functions of the map in Navigation mode
When the map is open in Navigation mode, tap any point on the map.
Buttons with various functions will be displayed.
2D/3D: Changes between 2D and 3D mode. The symbol indicates the current
mode.
Day/Night: Changes between "Day" and "Night" display modes. The symbol
indicates the current mode.
Interim Destination: Opens the menu for entering an interim destination.
The navigation system will first guide you to this interim destination.
Afterwards you can continue your original navigation.
Skip Route Point: Tap this button to omit the next route point. This button is
active only when at least 2 route points still lie ahead of you. (Refer to
"Multi-leg routes" on page 33)
Navigation
- 43 -
User’s manual NAVIGON 72xx
Block: Tap on this button in order to block a section of the route that lies in
front of you, i.e. to recalculate the route in order to avoid this section,
e.g. if you have heard on the radio of a traffic jam affecting this section.
(Refer to "Block" on page 48.)
Tap on this button again to remove the block.
POI on Your Route: Tap on this button to display POIs on your route. This way
you can quickly find out, for example, how far it is to the nearest
services. A destination shown here can be added as an interim
destination by tapping the
of its entry in the list.
(Interim Destination) button to the right
Note: The categories for the POI on Your Route function are the same
as those available for the Direct Access function. You can configure
which categories they are. (Refer to "Direct access to POI" on page 28)
6.6.4
Reality View PRO
The map switches to Reality View mode when you approach one of the
following points while driving on the motorway:
►
a motorway junction
►
a three-leg motorway junction
►
the exit you must take to leave the motorway
The Reality View mode shows with greater clarity the signposting and
lanes you must follow.
This display does not change until you have passed the spot indicated.
The map will then change back to Navigation mode.
►
- 44 -
If you want to change to Navigation mode before then, just tap on
any point on the map.
Navigation
User’s manual NAVIGON 72xx
Note: The Reality View mode is not available for all motorway
junctions and three-leg motorway junctions. Availability depends on the
map material used.
6.6.5
Map in Destination search mode
The map is always in Destination search mode, when a pair of cross
hairs are to be seen. Indicated in the address box are the coordinates
and, where applicable, the name of the street under the cross hairs.
When you are driving, the map does not change. It is always orientated
with north at the top.
Zoom Out: The map section shown becomes larger, but you will see
fewer details.
Zoom In: The map section becomes smaller, but you will see more
details.
Zoom Mode: When this button is active you can mark out a section of
the map with the stylus or your finger.
Mark out the section from upper left to bottom right to zoom in until the
section fills the screen.
Mark out the map section from bottom right to top left to zoom out.
Pan Mode: When this button is active you can change the section of
map displayed with the stylus or your finger. Simply drag the map in the
desired direction.
Entire Route: Zooms the map so that the entire route is visible.
Navigation
- 45 -
User’s manual NAVIGON 72xx
Current Position: Selects the section of map displayed so that the
current location is at the centre.
Operating in Destination search mode
1. Tap on the point to which you want to navigate.
The destination that you have selected appears under the cross
hairs.
The geographical coordinates of the destination and the
corresponding address are shown in the bottom third of the screen.
2. Tap on
(OK)
Buttons with various functions will be displayed.
Take Me There: Starts navigation to the selected point. If you are currently
navigating, this route navigation will be cancelled.
Interim Destination: Sets the selected point as interim destination. The
navigation system will first guide you to this interim destination.
Afterwards you can continue your original navigation.
This function is only active during navigation.
Set as Destination: Adds the selected point to the route planning as the last
point. Navigation will then continue to this point after you have reached
the original destination or the other route points. The function is
available only during navigation.
Save: Opens the SAVE DESTINATION AS... window. You can enter a name
under which the selected point will be saved in the FAVOURITES list.
(Refer to "Saving destinations" on page 33.)
Search Nearby: Opens the POI NEARBY window. Here you can search for
destinations near the selected point. (Refer to "POI nearby” page 25)
►
►
Tap on
(Destination search) in order to quit Destination
search mode. You will be returned to the window from which you
started this mode.
Tap on
(Back) in order to return to the NAVIGATION
window. If you are currently navigating, you will be prompted to
confirm your decision to quit navigation.
6.7
Useful functions
6.7.1
Direct Help
If you arrive at the scene of an accident or have an accident yourself, it
may be necessary to call for emergency aid and to give the answering
office your current location.
- 46 -
Navigation
User’s manual NAVIGON 72xx
►
Tap on Options > Direct Help.
The DIRECT HELP window opens.
If GPS reception is good enough, the address and the geographic
cooordinates of your current location will be indicated.
►
Tap on
(Show on Map) if you want to view your current location
on the map.
In the bottom half of the window you will find the buttons for
4 categories: Petrol Station, Police Station, Hospital, Pharmacy.
►
Tap on the corresponding button.
The nearest help point in the selected category will be indicated.
You are shown the name, address, phone number (if known),
distance and direction of the help point from your current location.
You have the following options:
►
Tap on
(Call) in order to call the number indicated.
The Call button is not available if no phone number is saved for the
help point or if the navigation device has no Bluetooth connection to
a mobile phone.
►
►
►
Tap on
(Show on Map) in order to see your location and the
help point on the map. This gives you an overview of the route to
the help point.
Tap on Start Navigation. You will then be guided directly to the
displayed help point.
You can use the
(Up) and
(Down) buttons to select other
help points in the selected category.
The help points are sorted by distance from your current position.
►
Use the
window.
(Back) button to return to the DIRECT HELP
Note: Only those help points are displayed which are situated no further
than than 30 mi from your position.
6.7.2
GPS Status, saving the current location
In the GPS STATUS window you will find an overview of the data the
navigation system calculates from the GPS signals it receives.
The GPS status can be accessed from the options button in many
windows.
►
Tap on Options > GPS Status.
The current location can be saved in the FAVOURITES list.
Navigation
- 47 -
User’s manual NAVIGON 72xx
1. Tap Save Position.
The SAVE DESTINATION AS... dialog box opens.
2. Enter a name for the destination.
3. Tap on Save.
6.7.3
Block
You can block a leg of the route at any time during a navigation, i.e. to
re-calculate the route in order to avoid the leg, e.g. if you have heard on
the radio of a traffic jam affecting this section.
Note: The block is valid only for the current navigation. It no longer
exists on a new navigation.
You are currently in a navigation. The map is open in Navigation mode.
1. Tap on any position on the map.
Buttons with various functions will be displayed.
2. Tap on Block.
The BLOCK menu opens.
3. Enter how many miles (from your current position on) you want to
block.
The system re-calculates the route. The blocked route section will be
avoided. It is marked on the map in red.
Unblocking a route section
1. Tap on any position on the map.
2. Tap Unblock.
The block will be lifted. The system recalculates the route. The unblocked route section can now be integrated into the calculation.
6.7.4
Turn-by-Turn List
You can display detailed directions of the calculated route before
starting navigation or at any time during navigation. This list displays all
of the driving instructions in table form.
The map is open in Preview mode, Navigation mode or Reality View
mode.
►
Tap on Options > Turn-by-Turn List.
The TURN-BY-TURN LIST window opens.
- 48 -
Navigation
User’s manual NAVIGON 72xx
1
Schematic depiction of the next junction where you must make a turn.
2
Distance to this junction.
3
Route instruction and if available the name of the street into which you
must turn.
4
Indicates whether you want to drive on the route section in question or
not.
(Allow): The section in question is allowed on the route.
(Forbid): The section in question is not allowed on the route.
Blocking route sections
1. Tap on the route sections that you do not want to travel on so that
the
(Forbid) symbol appears next to them.
2. Tap on
(Modify Route)
The navigation system calculates an alternative route avoiding the
route sections selected. The new driving instructions are displayed
in the TURN-BY-TURN LIST window.
3. Tap on
window again.
(Back) in order to close the TURN-BY-TURN LIST
Removing blocks and using original routes
Section blocks can be removed at any time.
►
Navigation
In the TURN-BY-TURN LIST window, tap on Options > Calculate
Original Route.
- 49 -
User’s manual NAVIGON 72xx
6.7.5
TMC (Traffic Information)
The integrated TMC receiver enables the navigation system to make
use of current traffic messaging. If necessary it can change your route
dynamically, for example in order to avoid a traffic jam.
Note: TMC is available free of charge in many European countries.
PremiumTMC, promising a faster and more up-to-date service, is
offered (exclusively or in addition) in some countries at a charge.
You can subscribe to PremiumTMC services on our website
www.navigon.com.
Displaying traffic information
Current traffic information is available via the options button in many
windows.
►
Tap on Options > Traffic.
The TRAFFIC INFORMATION window opens.
1
The Traffic Information button shows the type of traffic messaging listed
and how many messages of this type are in the list.
►
2
- 50 -
Tap on Traffic Information in order to select the messages you want
displayed.
This mark indicates that the message in question comes from a
PremiumTMC provider.
Navigation
User’s manual NAVIGON 72xx
3
Here you can see how serious the obstruction is:
Red: The section is blocked by the obstruction. This can be the case for
example with very long traffic jams or road blocks.
Yellow: The section is not blocked by the obstruction but there is a
threat of considerable delays. This can be the case for example with
traffic jams or when one of several lanes is blocked off.
No colour: The obstruction is not classified as serious. This can be the
case for example when slow-moving traffic is reported on a very short
section, when SOS telephones are not working or when parking areas
are blocked off.
4
Here you can see how far you are from this obstruction. If the
obstruction does not lie on your route or if a detour route was already
calculated for this obstruction, then the position of the message in the
list is indicated.
5
Here you can see in which state the obstruction lies. This information is
not displayed in American states.
Note: Most radio stations report only traffic obstructions in their own
state. You should therefore always tune into a station from the state in
which you currently find yourself. (Refer to "Tuning Mode" on page 51)
6
Here the reported obstruction is displayed as a traffic sign.
7
Here the affected road is indicated.
8
Here you can see on which section of the road the obstruction lies.
9
The navigation system can Detour (
) or Ignore (
the route. The button shows the active status.
►
Tap on the button to select the alternative setting.
You can use the
messages.
►
►
) congestion on
(Up) and
(Down) buttons to scroll in the list of
Tap on a message to display this information in detail.
Tap on
window again.
(Back) in order to close the TRAFFIC INFORMATION
TMC Settings
►
In the Settings window, tap on TRAFFIC INFORMATION.
In the TMC SETTINGS window you can set the TMC traffic station and
configure whether the reception of a traffic message concerning your
route should affect your route planning and if so how.
Tuning Mode
Tap on Tuning Mode and select a method for selecting the TMC radio
station.
Navigation
- 51 -
User’s manual NAVIGON 72xx
►
►
►
Automatic: You can use the arrow keys in the station area to select
another station. The system will search for another station if
reception becomes poor.
Hold station: You can use the arrow keys in the station area to
select another station. The system will search for the same station
on a different frequency if the signal becomes poor.
Hold frequency: You can use the arrow keys in the station area to
select another frequency. The system will not search for another
station if reception becomes poor.
Recalculate Route
Tap on Recalculate Route and select how new traffic messages
concerning your route are to be used.
►
►
Automatically: An alternative route will be calculated automatically.
The system will inform you on the recalculation.
On Request: An announcement from the navigation device tells you
that a traffic message concerns your route. On the screen the
Traffic Information box indicates the distance to the reported traffic
obstruction.
Tap on the Traffic Information box. You can then decide whether an
alternative route is to be calculated or not.
6.7.6
Logbook
You can use the NAVIGON 72xx to record a logbook. The logbook is
recorded in the "Logbook.xls" file. You can open the file with Microsoft
Excel. Each recorded trip is added at the bottom of the table as a new
entry.
The first time a trip is recorded, the "Logbook.xls" file will be created in
the "NAVIGON\Logbook" folder on the memory card in the navigation
device. If you delete or move this file, a new file will be created when
you next record a trip.
Note: Trips are recorded simultaneously in another file which is
compatible with the WISO Sparbuch program. This file is called
"MN7DriversLog.bin". It can also be found in the "NAVIGON\Logbook"
folder on the memory card in the navigation device.
Recording trips
You can have all trips recorded automatically.
1. In the NAVIGATION window, tap on Options > Settings > Navigation.
2. Set Logbook to Yes.
3. Tap on OK.
Every trip from now on will be recorded until you reset Logbook to No. It
is possible, however, to exclude individual trips from the recording.
- 52 -
Navigation
User’s manual NAVIGON 72xx
Before a trip
If your trips are recorded in the logbook, a window for entering the trip's
key data is opened before navigation starts. You can also decide,
however, not to record the trip in question.
►
If you don't want to record the trip in question, tap on
(Cancel).
- OR –
1. Enter a name for this entry, e.g. "Trip to customerX", in the Logbook
Entry box.
2. Enter the mileage.
3. Tap on Reason for the Trip and select a reason for the trip from the
list of possibilities.
7
Handsfree Module
The hands-free function allows you to use the NAVIGON 72xx as a
hands-free module for your mobile phone.
Opening the hands-free module
►
Tap in the navigation application on
(Phone).
The HANDSFREE MODULE window opens.
Operating the hands-free module
All functions can be reached from the HANDSFREE MODULE window.
►
►
7.1
Tap on
(Navigation) in order to move the navigation
application into the foreground.
Tap on
(Back) in order to close the hands-free module and
return again to the previously opened window.
Connecting to a telephone
The NAVIGON 72xx must be connected to a mobile phone in order for
you to use the telephone functions.
If the NAVIGON 72xx was last connected to the same mobile phone,
the connection will be established without further prompting.
Note: You can configure the automatic connection. (Refer to "Bluetooth
Function" on page 57)
Problems occurring when trying to establish a Bluetooth connection can
have various causes:
Handsfree Module
- 53 -
User’s manual NAVIGON 72xx
►
Bluetooth is dectivated in the hands-free module of the
NAVIGON 72xx.
Activate Bluetooth. Make sure that the NAVIGON 72xx can be
detected by other Bluetooth devices. (Refer to "Bluetooth Function"
on page 57.)
►
Bluetooth is deactivated on the mobile phone or it is set to "Hidden".
Activate Bluetooth on your mobile phone. Make sure that your
mobile phone can be detected by other Bluetooth devices
For more details refer to your mobile phone manual.
►
It may be that the NAVIGON 72xx was never connected to your
mobile phone before.
Initiate the connection manually. (Refer to "Connection with Mobile
Phone" on page 58.)
If the NAVIGON 72xx is still unable to establish a Bluetooth connection
to your mobile phone, contact your mobile phone manufacturer's
customer support.
7.2
Taking a call
When you receive a call, the INCOMING CALL window will open. You will
be asked whether you want to take the call. The name and the number
of the caller will be displayed if this information is available.
►
Tap on Yes if you want to take the call.
►
Tap on No if you do not want to take the call.
The CALL IN PROGRESS window opens.
Note: Navigation instructions are muted during a call.
7.3
Making a call
With the NAVIGON 72xx you can make a call in various ways:
7.3.1
Dialling a telephone number
1. Tap in the HANDSFREE MODULE window on the Keyboard button.
2. Enter the desired telephone number.
3. Tap on the Dial Number button.
7.3.2
Dialling a Speed Call number
You can configure 4 Speed Call buttons.
►
- 54 -
Tap in the HANDSFREE MODULE window on the corresponding
Speed Call button.
Handsfree Module
User’s manual NAVIGON 72xx
Note: If no number has been entered for the Speed Call button selected
or if no Bluetooth connection has been established to a mobile phone,
the MODIFY PRESET window will open.
For more details refer to chapter "Preset" on page 56.
7.3.3
Calling a contact from the phone book
You can select numbers from the phone book of the mobile phone to
which the NAVIGON 72xx is connected.
1. In the Phone Book window, tap on HANDSFREE MODULE.
2. Tap on the contact you want to call.
If more than one phone number is saved for this contact, a list with
all the phone numbers saved for the contact will open.
3. Tap on the number you want to dial.
Note: The phone book is not copied permanently to the navigation
device. It is available to the hands-free module only for as long as it is
connected to the mobile phone.
7.3.4
Calling most recently dialled, received or missed numbers
Note: The RECENT CALLS list contains outgoing, incoming and
unanswered calls. Incoming and unanswered calls can be dialled only
if the caller's number was transmitted.
1. Tap in the HANDSFREE MODULE window on the Recent Calls button.
2. Tap on the entry you want.
Note: The RECENT CALLS list is not copied permanently to the
navigation device. It is available to the hands-free module only for as
long as it is connected to the mobile phone.
7.3.5
Transferring a call from your mobile telephone
The NAVIGON 72xx takes calls automatically from the mobile phone as
soon as a Bluetooth connection is established between the two devices.
7.4
During a call
You are calling using the hands-free module. The CALL IN PROGRESS
window is open.
Handsfree Module
- 55 -
User’s manual NAVIGON 72xx
7.4.1
Moving the navigation application to the foreground
You can move the navigation application to the foreground at any time.
In this way you can have the map in the foreground during a call when
the NAVIGON 72xx is in the process of navigating.
►
Tap on the
(Navigation) button.
While a call is in progress, the
symbol (Call in Progress, green
mobile phone) is visible in the top right corner of the display.
►
7.4.2
Tap on the
button (Phone) in order to open the CALL IN
PROGRESS window again.
Entering numbers
You can enter numbers during a call. This may be the case, for
example, if a further connection via a telephone system is necessary.
1. Tap Keyboard.
2. Enter the desired numbers.
3. Tap on
window.
7.4.3
(Back) in order to open the CALL IN PROGRESS
Transferring a call to the mobile phone
►
In the CALL IN PROGRESS window, tap on Options > Use Mobile
Phone.
Pick up the mobile telephone and continue the call.
7.4.4
Ending the call
►
7.5
Tap in the CALL IN PROGRESS window on the Hang up button in
order to end the call.
Configuring the hands-free function
The hands-free module of the NAVIGON 72xx contains a number of
settings that can be individually configured.
For information about configuring the settings in this window refer to
"Configuring the NAVIGON 72xx" on page 60.
7.5.1
Preset
The hands-free module of the NAVIGON 72xx contains four Speed Call
buttons that can be individually configured.
- 56 -
Handsfree Module
User’s manual NAVIGON 72xx
1. In the HANDSFREE MODULE window, tap on Settings > Preset.
The MODIFY PRESET window opens.
2. Tap on the Speed Call button that you want to edit.
Entering a new Speed Call number or editing an existing Speed
Call number
3. Tap on the Edit button.
4. Enter the name and the number for the selected Speed Call button
or edit the existing name and number.
5. Tap on OK.
Adopting a number from the phone book of the mobile phone
3. Tap on the From Phone Book button. This button is deactivated
when there is no connection to a mobile phone.
4. Tap on the entry which you want to adopt for the Speed Call.
5. Tap on OK.
Deleting a Speed Call number
3. Tap on the Delete button.
4. Confirm that you want to delete the Speed Call number.
The MODIFY PRESET window opens again. No phone number and
no name exist any longer for the selected Speed Call button.
7.5.2
Handsfree Settings
In the HANDSFREE SETTINGS window you can configure the settings for
the phone functions of the hands-free module of your NAVIGON 72xx.
►
In the HANDSFREE MODULE window, tap on Settings > Handsfree
Settings.
The HANDSFREE SETTINGS window opens.
Volume of the Phone Call: The volume of the phone call can be controlled
independently of the volume of the navigation application.
Volume of the Ring Tone: The volume of the ring tone can be controlled
independently of the volume of the navigation application.
7.5.3
Bluetooth Function
►
In the HANDSFREE MODULE window, tap on Settings > Bluetooth
Function.
The BLUETOOTH FUNCTION window opens.
Handsfree Module
- 57 -
User’s manual NAVIGON 72xx
Bluetooth Function: Select whether you want to activate the Bluetooth function
(Yes or No).
The hands-free module cannot connect to a mobile phone if the
Bluetooth function is deactivated.
Discoverable by Others: Select whether other Bluetooth-capable devices (in
particular mobile phones) should be able to detect the NAVIGON 72xx
(Yes or No).
Others May Connect: Select whether other devices should be able to initiate a
connection (Yes or No).
Reconnect Automatically: Select whether the connection to the last connected
phone is to be restored automatically (Yes or No) as soon it comes
within range again.
Note: The Discoverable by Others and Others May Connect settings
are effective only when the Bluetooth function is activated.
A Bluetooth connection can be established from the mobile phone only
when Yes is selected for both settings.
7.6
Connection with Mobile Phone
Note: The Bluetooth functions of both the NAVIGON 72xx and the
mobile phone must be configured accordingly in order for a Bluetooth
connection to be established between the two devices.
For details of how to configure the NAVIGON 72xx refer to chapter
"Bluetooth Function" on page 57.
For details of how to configure the mobile phone refer to the related
manual.
The NAVIGON 72xx can establish a connection to only one Bluetoothcapable mobile phone.
As a rule the NAVIGON 72xx will automatically establish a connection
to a mobile phone to which it was once connected already. However,
you can also use this function to establish a connection to a different
mobile phone while a connection between the NAVIGON 72xx and a
mobile phone already exists.
7.6.1
Establishing a connection from the navigation device
1. Make sure that the Bluetooth function is activated on both the
mobile phone and the NAVIGON 72xx.
2. In the HANDSFREE MODULE window, tap on Settings > Connection
with Mobile Phone > New Connection.
The navigation device looks for Bluetooth devices and lists all the
devices it recognises.
- 58 -
Handsfree Module
User’s manual NAVIGON 72xx
3. Tap on the name of your mobile phone.
The navigation device prompts you to enter a password.
4. Enter a four-digit password (any digits) in the Key box and tap on
OK.
Your mobile phone prompts you to enter a password.
5. Enter the same password as on the NAVIGON 72xx.
On the NAVIGON 72xx, the SETTINGS BT window opens. A
connection is established between the two devices.
6. Tap on
(Back) in order to return to the HANDSFREE
MODULE window.
7.6.2
Establishing a connection from the mobile phone
Note: Please consult the mobile phone's manual if you are uncertain
about how to carry out the following steps on the mobile phone.
1. Make sure that the Bluetooth function is activated on both the
mobile phone and the NAVIGON 72xx.
2. Using your mobile phone, search for other Bluetooth devices.
The navigation device is detected as NAVIGON.
3. Initiate a connection to the detected NAVIGON device.
The mobile phone prompts you to enter a password.
4. Enter a four-digit password (user-defined).
The NAVIGON 72xx prompts you to enter a password.
5. Enter the same password in the Key box as on the mobile phone
and tap on OK.
The HANDSFREE MODULE window opens. A connection is
established between the two devices. The name of the connected
mobile phone is displayed at the bottom edge of the screen.
7.6.3
Terminating the connection and deleting the connection
data
You can terminate the connection between the NAVIGON 72xx and the
mobile phone at any time.
Note: You don't need to terminate the connection manually. The
connection is terminated automatically when the mobile phone is moved
a distance of approximately10 m from the NAVIGON 72xx. In this case
the connection data are saved so that the connection can be restored
automatically when the mobile phone is close enough to the
NAVIGON 72xx again.
Handsfree Module
- 59 -
User’s manual NAVIGON 72xx
1. In the SETTINGS BT window, tap on Connection with Mobile
Phone > Clear Connection Data.
You will be prompted to confirm that you want to terminate the
connection.
2. Tap on the OK button.
Note: After the connection is terminated, the NAVIGON 72xx is no
longer able to establish an automatic connection to a mobile phone,
including the same mobile phone as for the last connection.
The next connection to a mobile phone must be established manually
(refer to chapter "Connection with Mobile Phone" on page 58).
8
Configuring the NAVIGON 72xx
The SETTINGS window is the starting point for customising the
NAVIGON 72xx to match your personal preferences.
Settings can be accessed via the options in the START window and via
the options in many windows of the navigation application.
►
Tap on Options > Settings.
The SETTINGS window of the navigation application has several buttons:
Navigation, Route Profile, Map Display and General.
►
Tap on a button to open the corresponding settings window.
The settings of the individual windows are distributed over several
screen pages. You can toggle between them with the
and
(To the Left)
(To the Right) buttons.
Some settings can have only one of two values. These settings can be
(Toggle) button. All possible values are visible.
recognised by the
The currently valid value is highlighted in white.
►
Tap on
(Toggle) in order to switch between the possible values.
Some settings can accept several different values. These settings can
be recognised by the
visible.
1. Tap on
(List) button. The currently valid value is
(List)
A list with all possible values opens. The currently valid value is
marked.
- 60 -
Configuring the NAVIGON 72xx
User’s manual NAVIGON 72xx
2. Tap on the value you want. It is now marked.
3. Tap on OK.
The list closes. The new value is indicated.
(Help) button. When you tap on it you
For each setting there is a
will see an exact definition of the setting in question.
You can close the settings windows in two ways:
►
Tap OK.
Any changes you have made will be adopted.
►
Tap Cancel.
Any changes you have made will not be adopted.
Configuring the NAVIGON 72xx
- 61 -
User’s manual NAVIGON 72xx
9
Appendix
9.1
Technical data
Dimensions
Weight
Operating
conditions
115.6 x 74.8 x 18.7 mm
approx. 177 g
Operating
temperature
Storage
temperature
Humidity
CPU
Operating system
Display
Memory
RAM
GPS
TMC
Device keys
I/O
Keyboard
Loudspeaker
Microphone
Headset
Memory card
USB
Bluetooth
Power supply
Rechargeable
battery
Charging
Power pack
(accessories)
Car charger
cable
- 62 -
Type
Running time
Electronic
Duration
Input
Output
Input
Output
-10°C to 60°C (14°F to 140°F)
-30°C to 70°C (-22°F to 158°F)
0% to 90%, non-precipitating
Centrality Titan I 600 MHz
Microsoft Windows CE
4.3” LCD colour display with resistive
touch-panel
480 x 272 pixel (WQVGA)
Landscape, transmissive
128 MB
Yes (SiRF GRF3i+)
Built-in antenna
MMCX socket for external antenna
Yes
1 (On/Off)
Software keyboard
Yes
Yes
3.5 mm phone jack
MicroSD
USB 2.0
Integrated (CSR BlueCore 4)
With echo suppression
Via USB socket
Li-Ion, 1600 mAh
Up to 3 hours
Integrated
approx. 4-5 hours
100-240V ~ (alternating current, AC)
1.2A 5V = (direct current, DC)
10-24V = (direct current, DC)
1.2A 5V = (direct current, DC)
Appendix
User’s manual NAVIGON 72xx
9.2
Identification and serial number
The navigation system comes with various identification labels.
(Examples: CE mark, serial number, ...) These identification labels can
be found on the back of the device under a cover in the middle of the
recess for the cradle. On this cover is the NAVIGON logo.
If you need to see any of these labels, proceed as follows:
1. Insert a finger-nail in the recess on the top of the cover.
2. Pull the cover off the device.
To replace the cover:
1. Place the cover correctly in position.
2. Push the cover firmly against the device until it latches home in all
corners.
9.3
Declaration of conformity
The NAVIGON 72xx described in this manual bears the CE label
among others.
Products with the CE marking comply with Radio & Telecommunication
Terminal Equipment Directive (R&TTE) (1999/5/ECC), the
Electromagnetic Compatibility Directive (89/336/ECC) and the Low
Voltage Directive (73/23/ECC) – as amended by Directive 93/68/ECC –
issued by the European Community Commission.
Compliance with these directives implies conformity with the following
European Standards:
EN 300328 V 1.71, EN 301489-1 V 1.6.1, EN 301489-3 V 1.4.1,
EN 301489-17 V 1.2.1, EN 55022, EN 55024, EN 60950-1: 2001,
EN 50371: 2002, EN 50332: 2003, EN 61000-3-2, EN 61000-3-3,
EN 61000-4-2, EN 61000-4-3, EN 61000-4-4, EN 61000-4-5,
EN 61000-4-6, EN 61000-4-8, EN 61000-4-11
The manufacturer is not liable for modifications made by the user which
may alter the device's conformity with the CE label, nor for the
consequences thereof.
10
Troubleshooting
In this chapter you will find solutions to problems which may arise
during use of the NAVIGON 72xx.
This list does not claim to be complete. Answers to many other
questions can be found on the NAVIGON AG website. (Refer to
"Questions about the product" on page 7.)
Troubleshooting
- 63 -
User’s manual NAVIGON 72xx
I have connected a charger to the NAVIGON 72xx. A connection to a
computer is shown on the display.
or
I have connected the NAVIGON 72xx to a computer but it is not detected
as a removable disc.
The USB connector of the charger is not fully inserted in the case.
1. Unplug the connector.
The navigation device will carry out a new start. Wait for the
navigation software to be reloaded.
2. Without delay, insert the USB connector from the charger into the
corresponding socket of the NAVIGON 72xx as far as it will go.
(Refer to "Description of the NAVIGON 72xx" on page 8.)
The USB connector is not connected correctly. See above.
My NAVIGON 72xx makes no response any longer, the screen is frozen.
Perform a reset. This can be done in two ways:
►
Use a thin object to press the Reset button. (Refer to "Description of
the NAVIGON 72xx" on page 8)
- OR –
1. Press the
(On/Off) switch for at least 6 seconds.
The device is now deactivated.
2. Press the
(On/Off) key and keep it pressed until the device
switches on again. (Approx. 2 seconds)
The software will be restarted. Your settings and your saved
destinations and routes will be retained.
Note: Use only accessories which are recommended by NAVIGON
expressly for the NAVIGON 72xx. NAVIGON AG accepts no liability for
errors or damages resulting from the use of other accessories.
For suitable accessories go to www.navigon.com or your authorised
dealer.
- 64 -
Troubleshooting
User’s manual NAVIGON 72xx
11
Index
A
Address ............................................. 23
B
Block...................................... 44, 48, 49
Bluetooth ........... see Handsfree Module
Bluetooth Function ............................ 57
C
Call
Dial Number .................................. 54
Phone Book .................................. 55
Preset ........................................... 54
Recent Calls ................................. 55
Call in Progress
Enter numerals ............................. 56
Hang up ........................................ 56
Show Map ..................................... 56
Use handsfree .............................. 55
Use Mobile Phone ........................ 56
Compass ........................................... 17
Configuration ..................................... 60
Connection with Mobile Phone
Clear Connection Data ................. 59
Connection with Mobile Phone.... 53, 58
Conventions followed in this
manual................................................. 6
Current Position
Save.............................................. 47
D
Data entry.......................................... 20
Destination
Address................................... 23, 24
Direct Access................................ 28
Favourites ..................................... 29
From Map ..................................... 31
Home Address ........................ 30, 33
Imported addresses ...................... 30
Last Destinations .......................... 29
My Destinations ............................ 23
Index
New Destination ........................... 23
POI ............................................... 25
in a City .................................... 27
Nationwide ............................... 26
Nearby...................................... 25
Save ............................................. 33
Start Navigation ............................ 31
Take Me Home ....................... 30, 33
Turn-by-Turn List .......................... 32
Voice Command ........................... 24
Direct Help ........................................ 46
E
Energy......................................... 12, 17
Entering data..................................... 20
F
Favourites ................................... 29, 32
G
GPS
Faulty reception ............................ 21
Initialise......................................... 22
Signals.......................................... 14
Symbols ........................................ 16
GPS Status ....................................... 47
H
Handsfree Module
Bluetooth Function........................ 57
Call ............................................... 54
Call in Progress ............................ 55
Clear Connection Data ................. 59
Connection with Mobile Phone 53, 58
Dial Number.................................. 54
Enter numerals ............................. 56
Handsfree Settings ....................... 57
Hang up ........................................ 56
Incoming Call................................ 54
Open ............................................. 53
Phone Book .................................. 55
- 65 -
User’s manual NAVIGON 72xx
Preset ..................................... 54, 56
Recent Calls ................................. 55
Settings ......................................... 56
Show Map ..................................... 56
Symbols ........................................ 18
Use handsfree .............................. 55
Use Mobile Phone ........................ 56
Volume.......................................... 53
Handsfree Settings............................ 57
Home Address............................. 30, 33
Hotline ................................................. 7
I
Imported addresses........................... 30
Interim Destination ............................ 43
K
Keyboard ........................................... 18
L
Last Destinations......................... 29, 32
Logbook............................................. 52
M
Manual
Conventions .................................... 6
Symbols .......................................... 6
Map
Destination search ........................ 45
Navigation..................................... 41
Preview ......................................... 39
Reality View .................................. 44
Memory card ..................................... 13
Menu ................................................. 21
Muting................................................ 18
My Destinations................................. 23
- 66 -
N
Navigation
Block................................. 44, 48, 49
Interim Destination........................ 43
No GPS .................................. 32, 37
POI ............................................... 44
POI on Your Route ....................... 44
Route Profile........................... 31, 37
Skip Route Point........................... 43
Start ........................................ 31, 36
Turn-by-Turn List .................... 32, 37
Unblock......................................... 48
Navigation Application
Exit................................................ 22
Start .............................................. 21
NAVIGON 72xx
Description...................................... 8
Energy .......................................... 12
Installation .................................... 10
Memory card................................. 13
Scope of Delivery ........................... 7
Start .............................................. 14
TMC .............................................. 13
New Destination ................................ 23
O
Options.................................. 15, 20, 37
P
Password Lock.................................. 15
Phone................ see Handsfree Module
Phone Book....................................... 55
POI
Direct Access................................ 28
in a City......................................... 27
Nationwide.................................... 26
Nearby .......................................... 25
On route........................................ 44
Preset................................................ 56
Index
User’s manual NAVIGON 72xx
R
Reality View....................................... 44
Recalculate Route ............................. 52
Recent Calls ...................................... 55
Route Planning.................................. 33
Route points
Add ............................................... 34
Delete ........................................... 35
Order............................................. 35
Starting Point ................................ 34
Route Profile................................ 31, 37
Routes
Manage ......................................... 35
Planning........................................ 33
Route points.................................. 34
Route Profile ................................. 37
Save.............................................. 35
Show............................................. 36
Simulation ..................................... 36
Start Navigation ............................ 36
Starting Point ................................ 34
Turn-by-Turn List .......................... 37
S
Safety information ............................... 8
Scope of Delivery ................................ 7
Service ................................................ 7
Settings
Configuration ................................ 60
Volume.......................................... 43
Settings Handsfree Module
Bluetooth Function........................ 57
Clear Connection Data ................. 59
Connection with Mobile Phone ..... 58
Handsfree Settings ....................... 57
Preset ........................................... 56
Volume.......................................... 53
Simulation
Exit ................................................ 36
Start .............................................. 36
Skip Route Point................................ 43
Index
Software keyboard ............................ 18
Support................................................ 7
Symbols used in this manual .............. 6
T
Take Me Home............................ 30, 33
TMC
Recalculate Route ........................ 52
Show............................................. 50
Symbols ........................................ 17
Tuning Mode................................. 51
TMC Settings
Recalculate Route ........................ 52
TMC .............................................. 51
Traffic Information......................... 51
Tuning Mode................................. 51
Trade marks ........................................ 6
Traffic Information
Recalculate Route ........................ 52
Show............................................. 50
Tuning Mode................................. 51
Troubleshooting ................................ 63
Tuning Mode ..................................... 51
Turn-by-Turn List
Block............................................. 49
Show................................. 32, 37, 48
U
Unblock ............................................. 48
V
Voice Command ............................... 24
Volume ........................................ 43, 53
W
Warranty.............................................. 6
- 67 -
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement