Navigon 81XX GPS Receiver User Manual
User’s manual
NAVIGON 81xx
English (United Kingdom)
April 2008
The crossed-out wheeled bin means that within the European Union
the product must be taken to separate collection at the product end-oflife. This applies to your device but also to any enhancements marked
with this symbol. Do not dispose of these products as unsorted
municipal waste.
Imprint
NAVIGON AG
Schottmüllerstraße 20A
D-20251 Hamburg
The information contained herein may be changed at any time without prior
notification. Neither this manual nor any parts thereof may be reproduced for any
purpose whatsoever without the express written consent of NAVIGON AG, nor may
they be transmitted in any form either electronically or mechanically, including
photocopying and recording. All technical specifications, drawings etc are subject to
copyright law.
© 2008, NAVIGON AG
All rights reserved.
User’s manual NAVIGON 81xx
Table of contents
1
Introduction .......................................................................................6
1.1
About this manual.....................................................................................6
1.1.1
1.1.2
1.2
Legal notice ..............................................................................................6
1.2.1
1.2.2
1.3
2
Questions about the product ....................................................................7
2.1
Scope of Delivery .....................................................................................7
2.2
Description of the NAVIGON 81xx ...........................................................8
2.3
Important safety information.....................................................................8
2.4
2.5
Assembling the mains adapter ..................................................11
Charging the rechargeable battery ............................................11
Memory card..............................................................................12
Preparing the navigation system for use ...................................13
Navigating with GPS ..............................................................................14
Switching on the NAVIGON 81xx...................................................15
3.1
5
Navigation safety information ......................................................9
Safety information for the navigation device................................9
Safety guidelines when installing the device in your car ...........10
Preparing the NAVIGON 81xx for use....................................................11
2.4.1
2.4.2
2.4.3
2.4.4
4
Liability.........................................................................................6
Trademarks .................................................................................7
Before you begin...............................................................................7
2.3.1
2.3.2
2.3.3
3
Conventions.................................................................................6
Symbols .......................................................................................6
Options in the Start window....................................................................15
Password Lock................................................................................16
4.1
Activating password protection...............................................................16
4.2
Changing a password.............................................................................16
4.3
Cancelling password protection .............................................................17
4.4
Forgotten your password?......................................................................17
Operating the NAVIGON 81xx ........................................................17
5.1
Volume ...................................................................................................17
5.2
Information .............................................................................................18
5.3
Software keyboard .................................................................................20
5.3.1
5.3.2
Special keys ..............................................................................21
Entering data .............................................................................22
5.4
Options ...................................................................................................22
5.5
Menus.....................................................................................................22
User’s manual
Table of contents Š III
User’s manual NAVIGON 81xx
6
Navigation .......................................................................................22
6.1
Starting the navigation application .........................................................23
6.2
Specifying a destination .........................................................................24
6.2.1
6.2.2
6.2.3
6.2.4
6.2.5
6.2.6
6.2.7
6.2.8
6.2.9
6.2.10
6.2.11
6.3
Managing destinations ...........................................................................33
6.3.1
6.3.2
6.4
Saving destinations ...................................................................33
Defining a destination as home address ...................................34
Multi-leg routes.......................................................................................34
6.4.1
6.4.2
6.4.3
6.4.4
6.4.5
6.4.6
6.4.7
Entering the starting point..........................................................34
Entering route points .................................................................35
Editing route points....................................................................35
Managing routes ........................................................................36
Calculating and displaying routes..............................................37
Simulating routes .......................................................................37
Starting navigation.....................................................................37
6.5
Options in the navigation application......................................................38
6.6
Working with the map.............................................................................40
6.6.1
6.6.2
6.6.3
6.6.4
6.6.5
6.7
Maps ..........................................................................................40
Map in Preview mode ................................................................40
Map in Navigation mode............................................................42
Reality View...............................................................................44
Map in Destination search mode ...............................................45
Useful functions......................................................................................47
6.7.1
6.7.2
6.7.3
6.7.4
6.7.5
7
Specifying the country in which the destination is situated........25
Entering an address ..................................................................25
Selecting the destination address by voice command...............26
Points of interest........................................................................27
Information about the destination ..............................................30
Last Destinations .......................................................................30
Favourites ..................................................................................30
Contacts ....................................................................................31
Navigating home........................................................................31
Selecting destinations on the map.............................................32
Starting navigation.....................................................................32
Emergency Services..................................................................47
GPS Status, saving the current location....................................47
Turn-by-Turn List .......................................................................48
TMC (Traffic Information) ..........................................................49
Logbook .....................................................................................50
Handsfree Module...........................................................................51
7.1
Connecting to a telephone .....................................................................52
7.2
Taking a call ...........................................................................................52
7.3
Making a call ..........................................................................................53
7.3.1
Dialling a telephone number......................................................53
IV Š Table of contents
User’s manual
User’s manual NAVIGON 81xx
7.3.2
7.3.3
7.3.4
7.3.5
7.4
During a call ...........................................................................................54
7.4.1
7.4.2
7.4.3
7.4.4
7.5
9
10
Preset ........................................................................................55
Handsfree Settings ....................................................................56
Bluetooth Function.....................................................................56
Connection with Mobile Phone...............................................................57
7.6.1
7.6.2
7.6.3
8
Moving the navigation application to the foreground .................54
Entering numbers ......................................................................54
Transferring a call to the mobile phone .....................................54
Ending the call ...........................................................................55
Configuring the hands-free function .......................................................55
7.5.1
7.5.2
7.5.3
7.6
Dialling a Speed Call number to call home................................53
Calling a contact from the phone book ......................................53
Calling most recently dialled, received or missed numbers.......53
Transferring a call from your mobile telephone .........................54
Establishing a connection from the navigation device...............57
Establishing a connection from the mobile phone .....................57
Terminating the connection and deleting the connection
data............................................................................................58
Music................................................................................................58
8.1
Suitable files ...........................................................................................59
8.2
Opening the MP3 player.........................................................................59
8.3
Selecting an audio file ............................................................................59
8.4
Operating the MP3 player ......................................................................60
8.5
Music in the background ........................................................................61
Pictures............................................................................................61
9.1
Suitable files ...........................................................................................62
9.2
Opening the picture viewer.....................................................................62
9.3
Selecting an image file ...........................................................................62
9.4
Operating the picture viewer ..................................................................62
9.5
Play-back mode......................................................................................63
FM Transmitter ................................................................................63
10.1 Configuring the FM transmitter...............................................................64
11
12
Configuring the NAVIGON 81xx.....................................................64
Appendix .........................................................................................66
12.1 Technical data ........................................................................................66
12.2 Identification and serial number .............................................................67
12.3 Declaration of conformity........................................................................67
13
14
Troubleshooting..............................................................................68
Index ................................................................................................70
User’s manual
Table of contents Š V
User’s manual NAVIGON 81xx
1
Introduction
1.1
About this manual
1.1.1
Conventions
For better legibility and clarification, the following styles are used in this
manual:
Bold and italics:
Registered names, company and product
descriptions.
SMALL CAPITALS:
Window and dialogue box titles.
Bold:
Highlighting of important parts in the text.
Underlined:
Names of buttons, input boxes and other elements
on the user interface.
Underlined and italics:
Names of control elements on the navigation
device.
1.1.2
Symbols
The following symbols refer to specific passages of text:
Instructions and tips for operating the software
More detailed information and explanations
Warnings
1.2
1.2.1
Legal notice
Liability
The software and manual are subject to change without notice.
NAVIGON AG is not liable for the accuracy of the information contained
in this manual or for damages resulting from the use of this manual.
Suggestions for improvements and information regarding errors are
always welcome so that we can supply you with even better products in
the future.
-6-
Introduction
User’s manual NAVIGON 81xx
1.2.2
Trademarks
All brand and trade marks mentioned in this document and registered
by third parties are subject without reservation to copyright law and the
proprietary rights of their respective owners. All trade marks, trade
names and company names used in this document are or may be trade
marks or registered trademarks of their respective owners. All rights
reserved except those explicitly granted.
If the registered trademarks used in this manual are not explicitly
identified as such, this does not imply that the name is not subject to the
rights of a third party.
►
►
1.3
Microsoft, Outlook, Excel, and Windows are registered trade marks
of the Microsoft Corporation.
NAVIGON is a registered trade mark of NAVIGON AG.
Questions about the product
You have a question concerning your product? Then visit our webseite
www.navigon.com and click on "Support". There you will find an area
with frequently asked questions (FAQ Center) along with details of how
to contact us by phone or e-mail.
2
Before you begin
2.1
Scope of Delivery
Please check that the contents are complete. If anything is missing, get
in touch immediately with the dealer who sold you the product.
The purchased product includes the following:
►
NAVIGON 81xx navigation device
►
Car cradle
►
Car charger cable (10-30V adapter for the vehicle's cigarette lighter)
with integrated TMC antenna
►
Power pack (100-240V) with plug adapters
►
USB cable
►
SD card with software and navigation maps (the SD card is already
inserted in the navigation device)
►
The present manual
►
Leaflet with illustrated installation instructions
►
►
Before you begin
CD with manuals (PDF; including languages which are not available
in printed form) and additional programs (NAVIGON Fresh for
updating the software and NAVIGON Sync for exporting addresses
from Microsoft Outlook)
Cloth pouch
-7-
User’s manual NAVIGON 81xx
2.2
Description of the NAVIGON 81xx
1

2
Touch-screen
3
Volume on/off
4
Connection for external GPS antenna
5
Mini-USB socket for USB cable / Mains adapter / Car
charger cable
6
LED
7
Reset
Headset socket
8
-
Quieter
10
Microphone
11 +
Louder
12
Stylus
13
Slot for SD/SDHC memory card
14
On/Off
9
2.3
Back
Important safety information
In your own interest, please read the following safety information and
warnings carefully before starting up your navigation system.
-8-
Before you begin
User’s manual NAVIGON 81xx
2.3.1
Navigation safety information
Use the navigation system at your own risk.
Caution! To prevent accidents, do not operate the navigation system
while driving.
Caution! Do not look at the display unless it is absolutely safe to do so!
Caution! Traffic regulations have priority over any instructions from the
navigation system.
Caution! Follow the instructions of the navigation system only when the
circumstances and the road traffic regulations allow you to do so! The
navigation system will still guide you to your destination even if you
deviate from the calculated route.
Caution! Check that the cradle is secured and adjusted properly before
each journey.
Note: If you have not understood the spoken instructions or are unsure
about what to do next, you can refer briefly to the map or schematic
view of your navigation system.
2.3.2
Safety information for the navigation device
Caution! Protect the device from moisture. The device is neither
waterproof nor protected against splash water.
Caution! Do not open the case of the navigation device under any
circumstances.
Caution! Do not expose the navigation device to extreme heat or cold.
This may damage the device or impair its function. (See "Technical
data", page 66)
Caution! Use only the charger provided or one that has been approved
by the manufacturer.
Connect the charger to a suitable power supply. The voltage
requirements can be found on the device case and/or the packaging.
Note: Do not kink the cable. Make sure that the cable cannot be
damaged by sharp-edged objects.
Before you begin
-9-
User’s manual NAVIGON 81xx
Note: Clean the navigation device only with a damp cloth.
Note: Do not unplug by pulling on the cable. Doing so could damage
the cable!
Note: If you want to transport the navigation device, use the cloth
pouch provided in order to protect the touch-screen from scratches.
Note: Create a backup of the data contained on the memory card
provided. This is very easy to do with the NAVIGON Fresh software
which is included on the CD provided or can be downloaded free of
charge from our webseite www.navigon.com.
Note: The memory card must remain inserted in the device during
operation of the navigation system.
Note: Use only SD or MMC memory cards! Make sure that the memory
card contacts are clean and undamaged.
2.3.3
Safety guidelines when installing the device in your car
Caution! Fasten the cradle so that the navigation device is easy to see
and operate by the driver. Make sure that the driver's view of the traffic
is not impeded.
Caution! Do not attach the cradle within the working zone of any
airbags.
Caution! Do not fasten the cradle too close to the steering wheel or
other controls. The driver must not be obstructed in operating any car
functions.
Caution! When installing the cradle, make sure that it will not pose a
risk in the event of an accident.
Caution! Do not run cables directly next to safety-relevant devices and
power supplies.
Caution! Check the cradle regularly to make sure that it is securely
seated. The suction cup may become loose after a while.
- 10 -
Before you begin
User’s manual NAVIGON 81xx
Caution! After installation, check all safety-relevant equipment in the
car.
Caution! Connect the car charger cable only to 10-30V cigarette
lighters.
Caution! Disconnect the car charger cable from the cigarette lighter
whenever you park the car. The integrated mains adapter always
consumes a small amount of energy and could drain the car battery.
2.4
Preparing the NAVIGON 81xx for use
2.4.1
Assembling the mains adapter
The mains adapter has an operating voltage of 100~240V. Several
different plug adapters are provided. Charging the navigation device
when abroad is therefore no problem.
►
2.4.2
Push the correct plug adapter for the country in question into the
slot on the mains adapter until it locks in place.
Charging the rechargeable battery
It is possible that the rechargeable battery is not fully charged when you
unpack the navigation device. We recommend that you fully charge the
battery before using the device for the first time.
►
Connect the mains adapter to the navigation device and to a mains
socket.
Note: Without delay, plug the USB connector into the navigation device
as far it will go! (See "Troubleshooting" on page 68)
During charging, the LED on the bottom of the NAVIGON 81xx shines
with an orange light.
The LED goes out again when the NAVIGON 81xx is fully charged.
Note: When the bluetooth function of the NAVIGON 81xx is active, the
LED shines with a blue light. This is also the case during charging.
For detailed information refer to chapter "Handsfree Module" on
page 51.
Note: It takes approx. 4-5 hours to charge the device when the battery
is flat.
Before you begin
- 11 -
User’s manual NAVIGON 81xx
2.4.3
Memory card
A memory card with the software and card data is already inserted in
the navigation device.
You can copy these data to another memory card or save them on your
PC. To do so, use the NAVIGON Fresh software which is included on
the CD provided or can be downloaded free of charge from
www.navigon.com.
The following memory media can be used in the NAVIGON 81xx:
►
SD cards with maximum 2 GB
►
SDHC cards
Removing the memory card
1. Switch off the navigation device. To do so, press the
key.
(On/Off)
2. Press the memory card gently into the device until the lock
disengages.
3. Let go of the memory card. It will now project slightly out of the
device.
4. Pull the memory card out of the slot.
Inserting a memory card
1. Insert the memory card into the device (see illustration).
2. Press the card into the device until it locks in place.
Note: The navigation device will work only if the memory card contains
the navigation software and map data.
- 12 -
Before you begin
User’s manual NAVIGON 81xx
2.4.4
Preparing the navigation system for use
Caution! Be sure to refer to all the safety information in chapter
"Important safety information" on page 8.
Securing the cradle
1. Clean that part of the windscreen to which you want to secure the
cradle. The windscreen must be dry and free of dirt and grease.
2. Use the suction cup to fix the cradle to the windscreen.
3. Press the lever on the suction cup forwards.
Supplying power to the navigation device
Included in delivery of the NAVIGON 81xx is a car charger cable with
which power can be supplied to the navigation device via the vehicle's
cigarette lighter.
Connect the car charger cable to the vehicle's cigarette lighter and to
the mini-USB socket on the cradle. The navigation device will be
supplied with power as soon as it is inserted in the cradle.
Note: Power supply will only be possible via the cradle when the
navigation device is inserted. The device's USB socket will then be out
of function.
Caution! Connect the car charger cable only to 12V cigarette lighters.
TMC antenna
The NAVIGON 81xx has an integrated TMC receiver. A TMC antenna
is integrated in the car charger cable. As soon as the navigation device
is inserted in the cradle it can receive traffic message updates. Dynamic
route changes are thus possible, e.g. in order to avoid a traffic jam.
Inserting the navigation device into the cradle
Before you begin
- 13 -
User’s manual NAVIGON 81xx
On the rear of the navigation device is a ring which fits in the ring of the
cradle.
1. Align the head of cradle so that the button is on top.
2. Tilt the top end of the navigation device slightly towards yourself.
3. Position the recess in the ring of the navigation device so that it fits
in the ring of the cradle. (See illustration)
4. Press the device against the cradle until you hear it lock in place.
Removing the navigation device from the cradle
1. Press the button on top of the cradle.
2. Tilt the navigation device slightly towards yourself.
3. Remove the device from the cradle.
2.5
Navigating with GPS
GPS is based on a total of at least 24 satellites which are circling the
earth and constantly transmitting their position and time. The GPS
receiver receives this data and calculates its own geographical position
on the basis of the information transmitted by the various satellites.
Data from at least three satellites is required for positioning with an
acceptable degree of accuracy. With data from 4 or more satellites it is
possible in addition to determine the position's altitude above sea level.
Positioning is accurate to within three metres.
Once the navigation device has determined your position, this position
can be used as a starting point for calculating a route.
The map data on your navigation device includes the geographical
coordinates of all digitally recorded points of interest, streets and
places. This enables the device to calculate a route between a starting
point and a destination.
Calculation of the current position and its representation on the map
takes place once every second. In other words, your current position is
always shown on the map.
- 14 -
Before you begin
User’s manual NAVIGON 81xx
3
Switching on the NAVIGON 81xx
1. Press the
(On/Off) key.
If password protection has been activated, the ENTER PASSWORD
window opens.
2. Enter the password.
3. Tap on OK.
The START window opens.
Note: When you switch on the NAVIGON 81xx for the first time, you
will be asked to make the following settings:
►
your preferred language for using for the software
►
the unit of length for distances
►
the time format
From the START window you can access all applications of the
NAVIGON 81xx:
►
Navigation, see page 22
►
Music, see page 58
►
Pictures, see page 61
►
Phone (Handsfree Module), see page 51
►
FM Transmitter, see page 63. You can access this application via
the options in the START window.
Note: If you have not used the NAVIGON 81xx for a long time, the
battery may be flat.
In this case the device needs to be charged for approximately
10 minutes before it can be switched on.
Forgotten your password?
If you forget your password, follow the procedure described in
"Forgotten your password?" on page 17.
3.1
Options in the Start window
You can access more functions via the Options button.
1. Tap on Options to open the options list.
2. Tap on the option you would like to use.
►
If you would like to quit the options list without selecting an option,
tap on the Options button again.
Password Lock: You can protect your navigation system from unauthorised use
by creating a password. (Refer to page 16)
Switching on the NAVIGON 81xx
- 15 -
User’s manual NAVIGON 81xx
Product Information: Here you are shown the version numbers and copyright
details of the hardware and software.
Touchscreen Calibration: The touchscreen can be re-calibrated if it responds
poorly to touch. Follow the instructions on the screen.
Settings: Here you can make the settings which are to apply in all applications
of the NAVIGON 81xx, e.g. language, brightness and time format. For
details refer to chapter "Configuring the NAVIGON 81xx" on page 64.
Factory Settings: Resets all settings to the as-delivered state. Routes and
saved destinations are not deleted. The software is re-started and
behaves as if started for the first time after being purchased. (Refer to
"Switching on the NAVIGON 81xx" on page 15)
FM Transmitter: You can listen to driving instructions and music from the
NAVIGON 81xx over the car radio's loudspeaker system. (Refer to
page 63)
4
Password Lock
You can protect your navigation system from unauthorised use by
creating a password.
4.1
Activating password protection
1. In the START window, tap on Options > Password Lock.
The NEW PASSWORD window opens.
2. Enter a new password in the New password box.
3. Enter this password again in the Confirm new password box.
4. Tap on Activate.
Note: The password must have exactly 4 digits.
4.2
Changing a password
1. In the START window, tap on Options > Password Lock.
The ENTER PASSWORD window opens.
2. Enter the currently valid password in the Enter password box.
3. Tap on Change password.
The NEW PASSWORD window opens.
4. Enter a new password in the New password box.
5. Enter this password again in the Confirm new password box.
6. Tap on Activate.
- 16 -
Password Lock
User’s manual NAVIGON 81xx
Note: The new password must have exactly 4 digits.
4.3
Cancelling password protection
1. In the START window, tap on Options > Password Lock.
The ENTER PASSWORD window opens.
2. Enter the currently valid password in the Enter password box.
3. Tap on Deactivate.
4.4
Forgotten your password?
If you have forgotten your password, proceed as follows:
1. Tap on Info.
2. Follow the instructions on the screen.
5
Operating the NAVIGON 81xx
5.1
Volume
On the case of the NAVIGON 81xx you will find the following keys
(refer to "Description of the NAVIGON 81xx" on page 8):
-
Quieter
+
Louder
Volume on/off
You can use these keys to adjust the volume of the currently audible
application.
During a call
You can use the keys to adjust the volume of the phone call.
If an audio file is being played back at this moment, it will be muted for
the duration of the call.
If navigation instructions are being given at this moment, they will be
muted for the duration of the call.
During navigation
You can use the keys to adjust the volume of the navigation
instructions.
If an audio file is being played back at this moment, the keys will also
affect the volume of the MP3 player.
Operating the NAVIGON 81xx
- 17 -
User’s manual NAVIGON 81xx
During play-back of an audio file
You can use the keys to adjust the volume of the MP3 player.
Other cases
In all other cases the keys have no effect.
5.2
Information
Various information icons are located at the top of many windows.
GPS
The GPS icon is visible only in the navigation application. It can indicate
the following GPS reception states:
No GPS (No symbol): The built-in GPS receiver is not operational.
Contact customer service if the problem persists.
No Signal: Data is being received from less than three satellites.
Position cannot be calculated.
GPS Ready: Data is being received from at least three satellites.
Position can be calculated.
For details of the GPS status refer to chapter "GPS Status, saving the
current location" on page 47.
Compass
The Compass icon is visible only in the navigation application. It shows
you in which direction you are currently moving. It can indicate the
following points of the compass: N, NE, E, SE, S, SW, W, NW.
TMC (Traffic Information)
The NAVIGON 81xx has an integrated TMC receiver which provides
the navigation system with traffic information updates. Dynamic route
changes are possible if necessary, e.g. in order to avoid a traffic jam.
Note: This function is only available if TMC traffic messages are being
transmitted in the country in which you are travelling. This is not the
case in all countries.
The TMC icon is visible only in the navigation application. It can indicate
the following TMC reception states:
Tuning: The TMC receiver is operational but cannot find a station that
is transmitting TMC signals. There are no active traffic messages.
- 18 -
Operating the NAVIGON 81xx
User’s manual NAVIGON 81xx
Tuning: The TMC receiver is operational but cannot find a station that
is transmitting TMC signals. Traffic messages are active however. This
can be the case, for example, when travelling through a tunnel.
TMC on Standby: Traffic messages can be received.
Note: The TMC antenna is integrated in the car charger cable. The
Tuning icon may also appear therefore in the following cases:
►
►
The NAVIGON 81xx has been placed in the cradle but the car
charger cable is not connected to the cradle.
The NAVIGON 81xx has not been placed in the cradle and the car
charger cable is not connected to the navigation device.
For details of the TMC function refer to chapter "TMC (Traffic
Information)" on page 49.
Energy
The Energy symbol can indicate the following states of the integrated
battery:
The device is being supplied by an external power source. The battery
is fully charged.
The device is being supplied by an external power source. The battery
is being charged.
The device is being supplied by its internal battery. The battery charge
is sufficient.
The device is being supplied by its internal battery. The battery charge
is low.
Bluetooth / Phone
The NAVIGON 81xx has an integrated Bluetooth hands-free module.
This enables you to use the device as a hands-free kit for a mobile
phone with Bluetooth capability.
The LED on the bottom of the NAVIGON 81xx shines with a blue light
when the Bluetooth function is activated. For more details refer to
chapter "Handsfree Module" on page 51.
The Phone icon can display the following states of the hands-free
module:
No Bluetooth (No symbol): The Bluetooth function is deactivated.
Not connected (red mobile phone): The NAVIGON 81xx has no
Bluetooth connection to another device.
Operating the NAVIGON 81xx
- 19 -
User’s manual NAVIGON 81xx
Connected (white mobile phone): The NAVIGON 81xx is connected to
a mobile phone and can be used as a hands-free car kit.
Call in Progress (green mobile phone): The hands-free module of the
NAVIGON 81xx is being used at the moment for a call.
FM Transmitter
The NAVIGON 81xx has an integrated FM transmitter. This means that
you can listen to all audio outputs via the car radio's loudspeakers. This
applies to the navigation instructions, music from the MP3 player and
phone calls with the hands-free module.
The FM Transmitter icon can indicate the following states of the
integrated battery:
No Signal (No symbol): The FM transmitter is deactivated.
FM Transmitter: The FM transmitter is activated. You can listen to
audio outputs from the device via the car radio. To do so, you must set
the radio to the frequency of the FM transmitter and the
NAVIGON 81xx must not be too far from the vehicle's antenna.
For details of the FM transmitter's functions refer to chapter "FM
Transmitter" on page 63.
Muting
The Muting icon is visible only in the navigation application. It can
indicate the following states:
No symbol: The navigation application is not muted.
Muting: The navigation application is muted. If the device is navigating
at the moment, you will not hear any driving instructions.
Note: This icon indicates only the muted state of the navigation
instructions. It says nothing about the MP3 player or the hands-free
system.
5.3
Software keyboard
A software keyboard appears on the screen when text entries are
necessary.
All entries can be made on the software keyboard using your fingertips.
Only capital letters can be entered.
When entering town or street names you need not enter any special
characters or umlauts. The navigation system fills in these characters
for you automatically. If, for example, you are searching for “Würzburg”,
- 20 -
Operating the NAVIGON 81xx
User’s manual NAVIGON 81xx
then simply enter "WURZBURG". Special characters may be helpful
however when naming saved destinations and routes.
5.3.1
Special keys
inserts a space.
deletes the character in front of the cursor.
opens the keyboard with numerals.
Latin, Cyrillic and Greek alphabet
opens the keyboard with the Latin alphabet.
opens the keyboard with the Cyrillic alphabet.
opens the keyboard with the Greek alphabet.
When you want to enter addresses, names or special destinations, the
keyboard with the alphabet for the country in question will open
automatically.
When you want to save a destination to Favourites or when you enter a
special destination category or a country, the keyboard with the
alphabet of the user interface will open automatically.
You can also switch from the Cyrillic or Greek keyboard to the Latin
keyboard. Many addresses can then also be entered as transliterations
or in the language of the user interface.
Example: The language of the user interface is English. You want to
navigate to Moscow. You have the following options:
►
"Москва" (Cyrillic)
►
"Moskva" (transliterated)
►
"Moscow" (English).
Note: Street names and place names can be entered only in the
language of the user interface if that is how they exist in the map's
database.
Umlauts, accents and other letters
Another keyboard with special characters is available for each alphabet.
opens the keyboard with Latin special characters.
opens the keyboard with Cyrillic special characters.
opens the keyboard with Greek special characters.
As soon as you have entered a special character the letter keyboard
reappears.
Operating the NAVIGON 81xx
- 21 -
User’s manual NAVIGON 81xx
Note: The Cyrillic alphabet has more letters than places available on
the Cyrillic keyboard. The missing letters are included on the keyboard
with Cyrillic special characters.
5.3.2
Entering data
Often, lists appear from which you can select an entry. This is the case,
for example, when you enter the name of a town.
As soon as you enter the first letter, the largest city in the given country
that begins with this letter appears.
As soon as you enter the second letter, a list appears with all locations
that begin with the letters entered.
If you enter additional letters, the list adapts to your entries. It only
contains entries that begin with the text that has been entered or
contain the text in the name. The more letters you enter, the shorter the
list will become.
You can use the
through the list.
(Up) button and the
(Down) button to move
To accept an entry from the list, simply tap on it.
The list closes as soon as you have accepted an entry.
5.4
Options
Some windows offer options that lead to more functions.
For details of all the options available refer to the following chapters:
"Options in the Start window" on page 15
"Options in the navigation application" on page 38
5.5
Menus
Some buttons have menus which open when activated.
Tap on a menu point to execute its function.
If you would like to quit the options list without selecting a function, tap
on the button you used to open the menu.
6
Navigation
Use the navigation system at your own risk.
Caution! Be sure to refer to all the safety information in chapter
"Important safety information" on page 8.
- 22 -
Navigation
User’s manual NAVIGON 81xx
Impaired GPS reception
If GPS reception is impaired, navigation will be interrupted. The
navigation application remains in the foreground.
As soon as GPS reception is restored, the navigation system calculates
any change of position which has occurred in the meantime. You can
then simply continue navigation.
Arriving at your destination
When you have reached your selected destination, a message to this
effect will be displayed.
Only your current position (orange arrow) will now be shown on the
map.
6.1
Starting the navigation application
You have switched on the navigation device and, if necessary, entered
the password. The START window is open.
1. Tap on Navigation.
The navigation application will be started. When you start the
navigation application for the first time, the following message will
appear:
"Please note that the road traffic regulations are prior to the
instructions of the navigation system. Please do not operate the
device while driving."
2. After you have read and fully understood the message, tap on OK.
If you do not accept the content of the message, tap on Cancel in
order to exit the navigation application.
The NAVIGATION window is opened. From here you can access all
the functions of the navigation application.
►
►
►
Tap on
foreground.
(Music) in order to move the MP3 player into the
Tap on
(Phone) in order to move the hands-free module
into the foreground.
Tap on
(Back) in order to move the START window back
into the foreground.
Initialising the GPS receiver
As soon as the navigation device has been switched on, initialisation of
the GPS receiver will begin.
The integrated GPS receiver is not initialised for the first time until the
navigation application is started for the first time. It can take up to
20 minutes to initialise the GPS receiver for the first time.
Navigation
- 23 -
User’s manual NAVIGON 81xx
Note: If the GPS icon indicates GPS Ready after far less than
20 minutes, it is advisable to leave the navigation device switched on
for at least another 15 minutes in order to ensure reliable operation of
the receiver.
Each time you switch on the navigation device after this, GPS reception
will start within a short time.
If the navigation device has not been switched on for more than a week,
it can take up to 10 minutes to re-initialise the receiver.
In the top right hand corner of the display, you will see the GPS icon. As
soon as data from at least 3 satellites is received, the icon will change
to
(GPS Ready).
Note: Initialisation takes the least time if you do not start driving until
the initialisation has finished.
For more details about the GPS icon refer to chapter "GPS" on
page 18.
Returning to the Navigation window
The NAVIGATION window opens when the navigation application is
started.
If another window of the navigation application is open, tap on
(Back). This will return you to the window you came from.
►
6.2
Tap on
opened.
(Back) repeatedly until the NAVIGATION window is
Specifying a destination
Under New Destination you can enter destinations to which you have
not yet navigated or which you have not saved.
You can enter an address here, select a special destination, or select a
destination from the quick search function.
Note: The first time that you want to enter a new destination you will be
asked to select the country in which your destination is situated.
Under My Destinations the NAVIGON 81xx provides the following lists
of destinations and addresses for you to select from:
►
►
- 24 -
LAST DESTINATIONS: destinations to which you have navigated on a
previous occasion.
FAVOURITES: all destinations that you have saved in the
NAVIGON 81xx.
Navigation
User’s manual NAVIGON 81xx
►
6.2.1
CONTACTS: all destinations which you have imported from Microsoft
Outlook.
Specifying the country in which the destination is situated
Above the entry boxes in the ADDRESS, POI IN A TOWN and POI
NATIONWIDE windows is the Country button. It shows the country code
of the country from which you can currently enter navigation
destinations.
If your destination is in a different country, then proceed as follows:
1. Tap on the Country button.
The COVERED COUNTRIES list opens.
2. Tap on the country in which your destination lies.
The COVERED COUNTRIES list closes.
The country code of the destination country will appear on the
button.
Note: The selection list contains only those countries whose maps are
on the SD card.
6.2.2
Entering an address
1. In the NAVIGATION window, tap on New Destination > Enter an
Address.
If you want to enter an address in a country in which normally the
street comes first (e.g. the USA, Canada, Australia, South Africa...),
then the INPUT SEQUENCE menu will open.
1a Select whether you would like to enter the street first and then the
location (Street First), or first the location and then the street (City
First).
Note: The following description is based on City First as the order for
entering the address.
The ADDRESS window opens.
2. Enter the name or the postal code of the destination town.
3. Enter the name of the destination street.
4. Enter the house number. If you do not know the number of the
house, then leave this box empty.
If you do not know the house number but know the name of a
nearby side street, then tap on the Cross Street box and enter the
name of this street. The navigation system will calculate a route to
the intersection of the streets you have entered.
Navigation
- 25 -
User’s manual NAVIGON 81xx
Note: It is not necessary to enter all the address details.
If you specify the town only, the navigation system will calculate a route
to the town centre.
If you specify only the town and street without specifying a house
number or cross street, the navigation system will calculate the best
route to this street.
5. Tap on Start Navigation.
Sometimes the destination cannot be found exactly because, for
example, the entered combination of place and street name exists
several times.
In this case a window will open with a list of all the addresses
matching your entry plus additional information.
If the entered house number is not included on the map, the window
will show an address with the house number closest to the one
entered.
►
Tap on the address to which you want to navigate.
The map opens in Preview mode. The destination is indicated on
the map.
For details of how to start navigation refer to chapter "Starting
navigation" on page 32.
6.2.3
Selecting the destination address by voice command
It is particularly convenient to select the destination address by voice
command.
1. In the NAVIGATION window, tap on Voice Command.
The VOICE COMMAND window opens.
Indicated at the top is the country from which you can select
addresses.
►
Tap on the country if your destination address is situated in a
different country. Then follow the instructions given by the
navigation system.
You will be asked for the address data in this order: City > Street >
House number.
2. Follow the instructions given by the navigation system.
When you have finished entering the address, the map will open in
Preview mode. The destination is indicated on the map.
For details of how to start navigation refer to chapter "Starting
navigation" on page 32.
- 26 -
Navigation
User’s manual NAVIGON 81xx
Note: The Voice Command function is not available for every
language. In the languages for which this function is not available, the
Voice Command button is replaced by the Show Map button.
6.2.4
Points of interest
Points of interest, also called POI (Points Of Interest) for short, are
useful addresses that are catalogued according to particular criteria.
Special destinations include ports, airports, restaurants, hotels, petrol
stations, public buildings, doctor's surgeries, hospitals, shopping
centres, etc.
POI can be represented on the map by symbols. Tap in the NAVIGATION
window on Options > Settings > POI in order to select the categories
you want to appear on the map.
POI nearby
POI nearby are special destinations located within a certain radius of
your current location. This means you can always find the nearest petrol
station for example, no matter where you are.
Note: GPS reception must be good enough for determining your
(GPS Ready) icon to see whether GPS
position. Check the
reception is good enough.
For details refer to chapter "Initialising the GPS receiver" on page 23.
Note: The Direct Access section offers 3 categories of POI from the
current vicinity which can be searched for quickly and without additional
entry.
For details refer to chapter "Direct access to POI" on page 29.
1. Tap in the NAVIGATION window on New Destination > Search for
POI > Nearby.
The POI NEARBY window opens.
2. Select a category from which you would like to find a POI.
If sub-categories exist for the category you have selected, the Sub
Category list opens.
3. Select the sub-category from which you would like to select a POI.
The Name of the Destination list opens. It contains the nearest POI
in the specified category, sorted by distance.
4. Tap on the name of the destination.
5. Tap on Start Navigation.
Sometimes the destination cannot be found exactly because, for
example, several restaurants with the same name exist.
Navigation
- 27 -
User’s manual NAVIGON 81xx
In this case a window opens with all the destinations matching your
entry plus additional information.
►
Tap on the destination to which you would like to navigate.
The map opens in Preview mode. The destination is indicated on
the map.
For details of how to start navigation refer to chapter "Starting
navigation" on page 32.
POI of nationwide significance
POI of nationwide significance are airports, sights, national monuments,
large ports etc. This way you can find well-known places of interest
even if you don't know the name of their location.
1. In the NAVIGATION window, tap on New Destination > Search for
POI > Nationwide.
The POI NATIONWIDE window opens.
2. Select a category from which you would like to find a POI.
The Name of the Destination list opens. It contains the POI from the
selected category, sorted alphabetically.
3. If the list is very long, you can shorten it by entering a few letters of
the destination.
4. Tap on the name of the destination.
5. Tap on Start Navigation.
The map opens in Preview mode. The destination is indicated on
the map.
For details of how to start navigation refer to chapter "Starting
navigation" on page 32.
POI in a particular location
POI in a particular location can be useful when navigating in an
unfamiliar town.
1. In the NAVIGATION window, tap on New Destination > Search for
POI > in a Town.
The POI IN A TOWN window opens.
2. Enter the name or the postal code of the destination town.
3. Select a category from which you would like to find a POI.
If sub-categories exist for the category you have selected, the Sub
Category list opens.
4. Select the sub-category from which you would like to select a POI.
- 28 -
Navigation
User’s manual NAVIGON 81xx
The Name of the Destination list opens. It contains POI from the
specified category, sorted alphabetically.
5. Tap on the name of the destination.
6. Tap on Start Navigation.
Sometimes the destination cannot be found exactly because, for
example, several restaurants with the same name exist.
In this case a window opens with all the destinations matching your
entry plus additional information.
►
Tap on the destination to which you would like to navigate.
The map opens in Preview mode. The destination is indicated on
the map.
For details of how to start navigation refer to chapter "Starting
navigation" on page 32.
Direct access to POI
The direct access area contains 3 categories of POI. Destinations in
your vicinity that correspond to one of these categories can be viewed
here quickly and without further entry.
►
Tap in the NAVIGATION window on Options > Settings > POI in order
to select the categories for direct access.
Note: GPS reception must be good enough for determining your
(GPS Ready) icon to see whether GPS
position. Check the
reception is good enough.
For details refer to chapter "Initialising the GPS receiver" on page 23.
1. In the NAVIGATION window, tap on New Destination.
The NEW DESTINATION menu opens.
In the Direct Access area you are shown the icons of those POI
catgeories that are available by direct access.
2. Tap on the category from which you would like to select a POI.
The Name of the Destination list opens. It contains the nearest POI
in the specified category, sorted by distance.
3. Tap on the name of the destination.
The map opens in Preview mode. The destination is indicated on
the map.
For details of how to start navigation refer to chapter "Starting
navigation" on page 32.
Navigation
- 29 -
User’s manual NAVIGON 81xx
6.2.5
Information about the destination
For many destinations that you specify, there will be further information
available, stored in the navigation system's database.
There is, for example, a telephone number available for many
restaurants. You can then call the restaurant to reserve a table, for
example.
One of the destination entry windows described above is open.
►
Tap on
(Destination Info).
The DESTINATION INFO window opens. It contains all the information
about the specified destination that is stored in the navigation system's
database.
►
►
►
Tap on Cancel in order to close the DESTINATION INFO window
again.
Tap on
map.
(Show on Map) in order to see the destination on the
Tap on
(Call) in order to call the number indicated.
Note: The Call function is only available when the NAVIGON 81xx is
connected via Bluetooth to a mobile phone.
For details of how to connect to a mobile phone refer to chapter
"Connecting to a telephone" on page 52.
6.2.6
Last Destinations
NAVIGON 81xx saves the last 12 destinations to which you have
navigated in the LAST DESTINATIONS list.
1. In the NAVIGATION window, tap on My Destinations > Last
Destinations.
2. Tap on the destination to which you would like to navigate.
3. Tap on Start Navigation.
The map opens in Preview mode. The destination is indicated on
the map.
For details of how to start navigation refer to chapter "Starting
navigation" on page 32.
6.2.7
Favourites
Destinations to which you want to travel often can be saved in the
FAVOURITES list.
In the FAVOURITES list you can save up to 500 destinations.
- 30 -
Navigation
User’s manual NAVIGON 81xx
Information on how to save a destination can be found in chapter
"Saving destinations" on page 33.
1. In the NAVIGATION window, tap on My Destinations > Favourites.
2. Tap on the destination to which you would like to navigate.
3. Tap on Start Navigation.
The map opens in Preview mode. The destination is indicated on
the map.
For details of how to start navigation refer to chapter "Starting
navigation" on page 32.
6.2.8
Contacts
Using the NAVIGON Sync program from the CD provided you can
export to you navigation system any contact addresses which you have
saved in Microsoft Outlook on your computer.
Contacts which have been saved with several addresses will appear
once with each address in the CONTACTS list.
1. In the NAVIGATION window, tap on My Destinations > Contacts.
2. Tap on the address to which you want to navigate.
3. Tap on Start Navigation.
The map opens in Preview mode. The destination is indicated on
the map.
For details of how to start navigation refer to chapter "Starting
navigation" on page 32.
6.2.9
Navigating home
In NAVIGON 81xx you can save an address as your home address.
You can navigate to your home address at anytime by activating a
single button.
The first time you tap on Take Me Home you will be asked to enter your
address.
Further information about entering your home address can be found in
chapter "Defining a destination as home address" on page 34.
►
In the NAVIGATION window, tap on Take Me Home.
If you have not yet entered your home address, a dialog box will
notify you of this.
Navigation starts. The route profile used for the previous navigation
will be applied.
Navigation
- 31 -
User’s manual NAVIGON 81xx
6.2.10
Selecting destinations on the map
You may select a destination directly on the map. This is a quick way to
select towns, streets and POI.
1. In the NAVIGATION window, tap on Options > Show Map.
(Destination search)
2. Tap on
The map opens in Destination search mode.
3. Tap on the point to which you want to navigate.
Note: Please refer to chapter "Map in Destination search mode" on
page 45 for detailed information on how to change the map view so that
your destination is easily seen.
The destination that you have selected appears under the cross
hairs.
The geographical coordinates of the destination and the
corresponding address are shown in the bottom third of the screen.
4. Tap on
(OK).
The DESTINATION ON MAP window opens. The detailed address data
of the selected destination is displayed in the upper left-hand
corner.
5. Tap Take Me There.
The map opens in Preview mode. The destination is indicated on
the map.
For details of how to start navigation refer to chapter "Starting
navigation" on page 32.
6.2.11
Starting navigation
The map is open in Preview mode.
The navigation destination is depicted by a small flag. The route and the
estimated trip time are indicated.
Route Profile
The route is calculated on the basis of a route profile.
►
If you want to view or change the route profile, tap Route Profile.
Note: If you change the route profile, the changes will also apply to
future navigations.
For information about individual route profile settings tap on the related
button (Help).
- 32 -
Navigation
User’s manual NAVIGON 81xx
Turn-by-Turn List
►
If you want to see detailed directions for the route, tap on Options >
Turn-by-Turn List.
For details of the functions in the TURN-BY-TURN LIST window refer to
chapter "Turn-by-Turn List" on page 48.
Start Navigation
►
Tap on Start Navigation or simply start driving.
No GPS reception
If GPS signal reception is not good enough, the following message will
appear: "GPS reception is currently not sufficient. Navigation starts
automatically as soon as GPS reception is OK again."
You have the following options:
►
►
►
Wait. As soon as GPS reception is good enough for determining
your position, the route will be recalculated and navigation will
begin.
Tap on Cancel. The window in which you entered your destination
will open again. Your destination is saved in the LAST DESTINATIONS
list.
Tap on Demo. The route will be calculated using the centre of the
destination location as starting point. Navigation will then be
simulated on this route.
Tap on
(Back) in order to terminate the demonstration.
Note: The Demo button is not available if you selected the destination
on the map.
6.3
Managing destinations
Every destination you enter and destinations from the LAST
DESTINATIONS and CONTACTS lists can be saved in the FAVOURITES list.
This makes sense if you frequently navigate to a particular destination.
6.3.1
Saving destinations
1. Enter a destination. (Refer to "Entering an address" on page 25 or
to "Points of interest" on page 27). Do not tap the Start Navigation
button!
2. Tap on Options > Save Destination.
- OR –
Navigation
- 33 -
User’s manual NAVIGON 81xx
1. Select a destination from the LAST DESTINATIONS list or from the
CONTACTS list. (Refer to "Last Destinations" on page 30 or to
"Contacts" on page 31). Do not tap the Start Navigation button!
2. Tap on Options > Save as Favourite.
3. Enter a name for the destination.
4. If you want to define the destination as your home address, tap on
(Toggle) so that the value Yes is highlighted in white.
5. Tap on Save.
6.3.2
Defining a destination as home address
One destination from the FAVOURITES list can be defined as your home
address.
Then you can always start navigation to this destination very quickly by
tapping in the NAVIGATION window on Take Me Home.
1. Select the destination which you want to define as your home
address from the FAVOURITES list. (Refer to "Favourites” on
page 30)
2. Tap on Options > Home Address.
The selected destination has now been saved as your home address.
Your home address now appears in the FAVOURITES list marked by a
house symbol.
6.4
Multi-leg routes
It is possible to plan routes without GPS reception, for example in the
comfort of your home. Planned routes can be saved for later use. This
allows you to plan as many routes as you like, for example for your
holidays.
1. In the NAVIGATION window, tap on Options.
The options list opens.
2. Tap on the Route Planning option.
The ROUTE PLANNING window opens.
6.4.1
Entering the starting point
The starting point of a route is the point at which you want to begin your
trip. This is not necessarily the current location. If you are planning a
route for your holidays at home, you could, for example, enter your
hotel as the starting point.
The starting point is only important if you want to see a planned route
on the map but currently have no GPS reception, or if you are not
currently at the planned starting point. This is why your selected starting
point has the flow number "0".
- 34 -
Navigation
User’s manual NAVIGON 81xx
As soon as you start navigation, your current location will be used as
the starting point for the route calculation.
The first leg of the route is therefore the journey to the route point with
flow number "1".
1. Tap on the Specify Starting Point box.
The STARTING POINT menu opens.
If you want to enter your current location as the starting point:
2. Tap on the Current Position menu item.
If you want to enter a different starting point:
2. Tap on the corresponding button.
3. Enter the starting point. (Refer to the corresponding section of
chapter "Specifying a destination" on page 24 ff.)
4. Tap on Set Starting Point.
The selected starting point will now be displayed next to the 0
button (Starting Point).
Changing the starting point
►
Tap on the Specify Starting Point box.
The STARTING POINT menu opens. You can now enter a different
starting point. Proceed as described above.
6.4.2
Entering route points
The route points of a route are the destinations that you want to
navigate to.
The flow number for each route point is indicated on a button in front of
it.
1. Tap on the Add Route Point box.
The ROUTE POINT menu opens.
2. Tap on the button for how you want to enter the destination.
3. Enter the route point. (Refer to the corresponding section of chapter
"Specifying a destination" on page 24 ff.)
4. Tap on Add.
The selected route point is now shown next to its flow number.
Repeat these steps for each destination that you want to add to your
route.
6.4.3
Editing route points
Route points can be deleted from a route. The order of the route points
can be changed as you wish.
Navigation
- 35 -
User’s manual NAVIGON 81xx
Note: The start point (flow number "0") can be neither moved nor
deleted.
►
Tap on the route point that you want to edit.
The context menu contains the following buttons:
Route Point Up: Moves the selected route point further to the front.
(Example: route point 2 becomes route point 1).
Route Point Down: Moves the selected route point further to the
back. (Example: route point 2 becomes route point 3).
Delete: Deletes the selected route point. A dialog window prompts
you to confirm deletion.
6.4.4
Managing routes
You can save each planned route under a particular name.
Note: Only the start point and route points will be saved, not the
calculated route. When you load a saved route, it must be recalculated
before navigation can start.
You can load, rename or delete stored routes.
Saving routes
The ROUTE PLANNING window is open. You have entered the starting
point and at least one route point.
1. Tap on Options > Save Route.
2. Enter a name for the route.
3. Tap on Save.
The route is now saved to the SAVED ROUTES list. The dialog
window closes.
Loading routes
1. Tap on Options > Saved Routes.
2. Tap on the route that you want to load.
3. Tap on Load Route.
The ROUTE PLANNING window opens. The starting point and the
route points of the loaded route have been entered.
- 36 -
Navigation
User’s manual NAVIGON 81xx
6.4.5
Calculating and displaying routes
It is possible to calculate and display a planned route on the map even
without GPS reception in order to get an impression of the journey.
The ROUTE PLANNING window is open. The starting point and at least
one route point have been entered.
1. Tap on Show Route.
The map opens in Preview mode.
The starting point and the route points are marked by flags. The
distance and the estimated trip time is given for each leg of the
route. The same data are also displayed for the entire route.
6.4.6
Simulating routes
It is also possible simply to simulate navigation on a planned route.
Note: GPS reception is not necessary for simulation.
If you have planned a multi-leg route, only the first leg will be simulated.
You have calculated and displayed a route.
►
Tap on Options > Simulation.
The route will be recalculated for simulation purposes. Simulation
starts when calculation has finished.
Stopping simulation
You can stop simulation at any time.
►
Tap on
(Back).
The ROUTE PLANNING window opens.
6.4.7
Starting navigation
You have calculated and displayed a route.
Route Profile
The route is calculated on the basis of a route profile.
If you want to view or change the route profile, tap on Route Profile.
Note: If you change the route profile, the changes will also apply to
future navigations.
Information about individual route profile settings can be obtained by
tapping the related
Navigation
(Help) button.
- 37 -
User’s manual NAVIGON 81xx
Turn-by-Turn List
If you want to see detailed directions for the route, tap on Options >
Turn-by-Turn List.
For details of the functions in the TURN-BY-TURN LIST window refer to
chapter "Turn-by-Turn List" on page 48.
Start Navigation
►
Tap on Start Navigation or simply start driving.
No GPS reception
If GPS signal reception is not good enough, the following message will
appear: "GPS reception is currently not sufficient. Navigation starts
automatically as soon as GPS reception is OK again."
You have the following options:
►
►
6.5
Wait. As soon as GPS reception is good enough for determining
your position, the route will be recalculated and navigation will
begin.
Tap on Cancel. The NAVIGATION window opens.
Options in the navigation application
Some windows offer options that lead to more functions.
►
Tap on Options to open the options list.
►
Tap on the option you would like to use.
►
If you would like to quit the options list without selecting an option,
tap on the Options button again.
Add to Route: Opens the route planning. The selected address will be entered
as the starting point of a new route.
For more details refer to chapter "Multi-leg routes" on page 34.
Delete All: Deletes all destinations in the list (LAST DESTINATIONS list or
FAVOURITES list, depending on where you opened the options). The list
is then empty. A dialog box prompts you to confirm deletion.
Delete: Deletes the selected destination from the LAST DESTINATIONS or
FAVOURITES list or the selected route from the SAVED ROUTES list. A
dialog box prompts you to confirm deletion.
Emergency Services: Opens a window in which your current location is
indicated. If the NAVIGON 81xx is connected to a mobile phone, you
can have yourself connected directly to the emergency hotline.
For information about connecting to a mobile phone refer to chapter
"Handsfree Module" on page 51.
- 38 -
Navigation
User’s manual NAVIGON 81xx
GPS Status: Opens the GPS STATUS window. Here you can see details
regarding GPS reception. You can also save the data of your current
location.
For details refer to chapter "GPS Status, saving the current location" on
page 47.
Home Address: Saves the selected destination as your home address. You can
then always start navigation to this destination very quickly by tapping in
the NAVIGATION window on Take Me Home.
New Route: Deletes the starting point and all route points from the ROUTE
PLANNING window so that you can plan a new route.
If necessary, save the previously planned route!
Rename: Opens a window in which you can change the name for the selected
destination or route.
Route Planning: Opens the ROUTE PLANNING window. Here you can plan
routes, manage planned routes and start navigation on a planned route.
For more details refer to chapter "Multi-leg routes" on page 34.
Route Profile: Opens the ROUTE PROFILE window. Here you can view the
options for route planning and, if necessary, change them.
Save as Favourite: Saves the selected destination to the FAVOURITES list.
For more details refer to chapter "Saving destinations" on page 33.
Save Destination: Saves the selected address in the FAVOURITES list.
For more details refer to chapter "Saving destinations" on page 33.
Save Route: Opens a window in which you can save the planned route under a
specific name.
For more details refer to chapter "Saving routes" on page 36.
Saved Routes: Opens a dialog window into which you can load a saved route.
Settings: Opens the SETTINGS window. Here you can configure the navigation
system.
For details refer to chapter "Configuring the NAVIGON 81xx" on
page 50.
Show Map: Opens the map in Destination search mode. Here you can select
your navigation destination directly on the map.
For details refer to chapter "Selecting destinations on the map" on
page 32.
Show on Map: Shows the selected address on the map.
Navigation
- 39 -
User’s manual NAVIGON 81xx
Simulation: Simulates a navigation on the route indicated. This simulation can
be performed without GPS reception. On multi-leg routes, only the first
leg is simulated.
Traffic: Opens the TRAFFIC INFORMATION window in which pending reports are
listed.
For more details refer to chapter "TMC (Traffic Information)" on
page 49.
Turn-by-Turn List: Shows detailed directions for the route, including all points at
which you must turn.
For details of the functions in the TURN-BY-TURN LIST window refer to
chapter "Turn-by-Turn List" on page 48.
6.6
Working with the map
6.6.1
Maps
Each country has its own navigation map. However, seamless
navigation over several maps on one continent is possible if a
continuous route can be planned on the maps saved.
Even if maps from several continents are saved on the memory card in
your navigation device, the NAVIGON 81xx can only ever work with
maps from one continent.
Tap in the NAVIGATION window on Options > Settings > Current Map in
order to see which maps are currently in use. Here you can also select
a different continent if the memory card in the navigation device
contains any maps of countries on other continents.
6.6.2
Map in Preview mode
You have entered a destination and tapped on Start Navigation.
- OR –
You have planned or loaded a route and tapped on Show Route.
- 40 -
Navigation
User’s manual NAVIGON 81xx
The map opens in Preview mode. The entire route is visible.
1
The route is highlighted in orange.
2
Your current position is indicated (orange arrow).
If you display a planned or loaded route and the specified starting point
is not your current location, then it is possible that your current position
will not be shown on the preview.
3
The destination is marked with a little flag.
If you display a planned or loaded route, the starting point and each
route point will be marked with a little flag.
4
You will see the total distance for the route in a small info box, together
with the estimated trip time and the estimated time of arrival.
You can select to show or hide this information in Options > Settings >
Basic Settings.
If you display a multi-leg route, you will see this information for each leg.
►
►
Tap on Route Profile in order to view and, if required, change the
settings which form the basis for the route planning.
Tap on Start Navigation to start the trip.
If you display a planned or loaded route, the route may be
recalculated. The starting point for the calculation will now be your
current location. You will first be guided to the first route point
entered.
►
►
Navigation
Tap on Options > Turn-by-Turn List to view detailed directions for
the route. (Refer to "Turn-by-Turn List” on page 48)
Tap
(Destination search) to view the map in Destination
search mode. (Refer to "Map in Destination search mode" on
page 45)
- 41 -
User’s manual NAVIGON 81xx
6.6.3
Map in Navigation mode
After the route was shown in Preview mode, navigation was started.
The map opens in Navigation mode.
1
Here you can see the signposting which you must follow.
2
Here you can see any speed limits which are in force.
3
The route is highlighted in orange.
4
When two manoeuvres need to be executed in quick succession, the
small arrow box indicates the second manoeuvre to be executed.
5
The large arrow box shows a schematic depiction of the next junction at
which you must make a turn. The distance remaining to this junction is
indicated underneath.
As you get closer to the junction you will see a spot diagram in addition
to the distance:
The nearer you get to the junction, the more yellow spots are displayed.
If you don't have to change direction for a long time, you will see only a
straight arrow. The distance you must continue straight on is indicated
underneath the arrow.
►
Tap on the large arrow box to hear current route instructions.
6
Ahead of many junctions the information from 7 and 8 is hidden. Instead
you are shown which lanes lead to your destination.
7
The height above sea level and the current speed are displayed here.
8
The distance remaining to the destination, the estimated duration of the
trip and the estimated time of arrival can be seen in the Total box.
- 42 -
Navigation
User’s manual NAVIGON 81xx
9
Your current position is indicated on the map (orange arrow). The
section of the map displayed changes continually so that your current
position is always in view on the map.
10
If you are navigating a multi-leg route, you will see the remaining
distance to the next interim destination, the estimated duration of the
trip and the estimated time of arrival in the Next box.
11
The name of the next stretch of road that you must travel on is
displayed in the upper street box.
12
The name of the stretch of road that you are currently travelling on is
displayed in the lower street box.
Note: The displays of many of the above mentioned areas can be
configured in Options > Settings > Basic Settings. Some displays will
only function if the required information is available on the map.
Note: If you tap on the large arrow box, the current route instruction will
be repeated.
►
►
Tap on Options > Turn-by-Turn List to view detailed directions for
the route. (Refer to "Turn-by-Turn List” on page 48)
Tap on
(Destination search) in order to view the map in
Destination search mode. (Refer to "Map in Destination search
mode" on page 45)
Volume
The volume of the spoken driving instructions can be adjusted during
navigation.
1. Tap on
(Volume).
The volume bar opens. It contains three buttons for adjusting the
volume.
(Louder),
2. Tap on
(Quieter),
(Volume on/off)
(Volume) again or wait a few seconds.
The volume bar closes.
Note: The volume can be controlled likewise with the keys of the
navigation device. (See "Volume" on page 17)
Quitting navigation
Tap on
(Back) in order to quit navigation. A dialog box will
prompt you to confirm.
Navigation
- 43 -
User’s manual NAVIGON 81xx
Functions of the map in Navigation mode
When the map is open in Navigation mode and you tap on any point on
the map, buttons with various functions will appear.
2D/3D: Changes between 2D and 3D mode. The icon indicates the current
mode.
Day/Night: Changes between "Day" and "Night" display modes. The icon
indicates the currently selected mode.
Interim Destination: Opens the menu for entering an interim destination.
The navigation system will first guide you to this interim destination.
Afterwards you can continue navigating to your original destination.
Skip Route Point: Tap on this button to omit the next route point. This button is
active only when at least 2 route points still lie ahead of you. (See
"Multi-leg routes" on page 34)
Block: Tap on this button in order to block a section of the route that lies in
front of you, i.e. to recalculate the route in order to avoid this section,
e.g. if you have heard on the radio of a traffic jam affecting this section.
Tap on this button again to remove the block.
POI on Your Route: Tap on this button to display POI on your route. This way
you can quickly find out, for example, how far it is to the nearest
services. A destination shown here can be added as an interim
destination by tapping the
of its entry in the list.
6.6.4
(Interim Destination) button to the right
Reality View
The map switches to Reality View mode when you approach one of the
following points while driving on the motorway:
- 44 -
►
a motorway junction
►
a three-leg motorway junction
►
the exit you must take to leave the motorway
Navigation
User’s manual NAVIGON 81xx
The Reality View mode shows with greater clarity the signposting and
lanes you must follow.
This display does not change until you have passed the spot indicated.
The map will then change back to Navigation mode.
►
If you want to change to Navigation mode before you have passed
the junction, just tap on any point on the map.
Note: Reality View is not available for all motorway junctions and
three-leg motorway junctions. Availability is dependent on the map data
in use.
6.6.5
Map in Destination search mode
The map is always in Destination search mode when the cross hairs
can be seen. Indicated in the address box are the coordinates and,
where applicable, the name of the street under the cross hairs.
When you are driving, the map does not change. It is always orientated
with north at the top.
Navigation
- 45 -
User’s manual NAVIGON 81xx
Zoom Out: The map section shown becomes larger, but you will see
fewer details.
Zoom In: The map section becomes smaller, but you will see more
details.
Zoom Mode: When this button is active you can mark out a section of
the map with the stylus or your finger.
Mark out the section from upper left to bottom right to zoom in until the
section fills the screen.
Mark out the map section from bottom right to top left to zoom out.
Pan Mode: When this button is active you can change the section of
map displayed with the stylus or your finger. Simply drag the map in the
desired direction.
Entire Route: Zooms the map so that the entire route is visible.
Current Position: Selects the section of map displayed so that the
current location is at the centre.
Operating in Destination search mode
1. Tap on the point to which you want to navigate.
The destination that you have selected appears under the cross
hairs.
The geographical coordinates of the destination and the
corresponding address are shown in the bottom third of the screen.
2. Tap on
(OK).
Buttons with various functions will be displayed.
Take Me There: Starts navigation to the selected point. If you are currently
navigating, this route navigation will be cancelled.
Interim Destination: Sets the selected point as interim destination. The
navigation system will first guide you to this interim destination.
Afterwards you can continue your original navigation.
This function is only active during navigation.
Set as Destination: Adds the selected point to the route planning as the last
point. Navigation will then continue to this point after you have reached
the original destination or the other route points. The function is
available only during navigation.
- 46 -
Navigation
User’s manual NAVIGON 81xx
Save: Opens the SAVE DESTINATION AS... window. You can enter a name
under which the selected point will be saved in the FAVOURITES list.
For more details refer to chapter "Saving destinations" on page 33.
Search Nearby: Opens the POI NEARBY window. Here you can search for
destinations near the selected point. (Refer to "POI nearby” page 27)
►
►
Tap on
(Destination search) in order to quit Destination
search mode. You will be returned to the window from which you
started this mode.
Tap on
(Back) in order to return to the NAVIGATION window.
If you are currently navigating, you will be prompted to confirm your
decision to quit navigation.
6.7
Useful functions
6.7.1
Emergency Services
If you arrive at the scene of an accident or have an accident yourself, it
may be necessary to phone the emergency hotline and give your
current location.
►
Tap on Options > Emergency Services.
The EMERGENCY SERVICES window opens. If GPS reception is good
enough, the address and the geographic cooordinates of your current
location will be indicated.
If the NAVIGON 81xx is connected to a mobile phone, you can have
yourself connected directly to the emergency hotline.
►
Tap on the Emergency Services button (in red).
You will now be connected to the emergency hotline. If the connection
fails, a dialog box will tell you which number to dial on your mobile
phone in order to get through to the emergency hotline.
Note: In some countries you can get through to the emergency hotline
with the number shown only if you use a mobile phone. Another number
may be necessary for landline calls.
6.7.2
GPS Status, saving the current location
In the GPS STATUS window you will find an overview of the data the
navigation system calculates from the GPS signals it receives.
The GPS status can be accessed from the options button in many
windows.
►
Tap on Options > GPS Status.
The current location can be saved in the FAVOURITES list.
1. Tap on Save Position.
Navigation
- 47 -
User’s manual NAVIGON 81xx
The SAVE DESTINATION AS... dialog box opens.
2. Enter a name for the destination.
3. Select whether you want to save your current position as the home
address.
4. Tap on Save.
6.7.3
Turn-by-Turn List
You can display detailed directions of the calculated route before
starting navigation or at any time during navigation. This list displays all
of the driving instructions in table form.
The map is open in Preview mode, Navigation mode or Reality View
mode.
►
Tap on Options > Turn-by-Turn List.
The TURN-BY-TURN LIST window opens.
1
Schematic depiction of the next junction where you must make a turn.
2
Distance to this junction.
3
Route instruction and if available the name of the street into which you
must turn.
4
Indicates whether you want to drive on the route section in question or
not.
(Allow): The section in question is allowed on the route.
(Forbid): The section in question is not allowed on the route.
- 48 -
Navigation
User’s manual NAVIGON 81xx
Blocking route sections
1. Tap on the route sections that you do not want to travel on so that
the
2. Tap on
(Forbid) symbol appears next to them.
(Modify Route).
The navigation system calculates an alternative route avoiding the
route sections selected. The new driving instructions are displayed
in the TURN-BY-TURN LIST window.
(Back) in order to close the TURN-BY-TURN LIST
3. Tap on
window again.
Removing blocks and using original routes
Section blocks can be removed at any time.
►
6.7.4
In the TURN-BY-TURN LIST window, tap on Options > Calculate
Original Route.
TMC (Traffic Information)
The integrated TMC receiver enables the navigation system to make
use of current traffic messaging. If necessary it can change your route
dynamically, for example in order to avoid a traffic jam.
Displaying traffic information
Current traffic information is available via the options button in many
windows.
1. Tap on Options > Traffic.
The TRAFFIC INFORMATION window opens.
Above the list the Traffic Information button indicates the type of
traffic information listed and how many messages of this type there
are in the list.
2. Tap on Traffic Information in order to select which messages you
want displayed.
For each traffic message in the list you are shown information about the
location of the traffic obstruction and its type.
►
Tap on a message to display this information in detail.
The navigation system can Detour (
) or Ignore (
the route. The button shows the active status.
►
►
Navigation
) congestion on
Tap on the button to select the alternative setting.
Tap on
(Back) in order to close the TRAFFIC INFORMATION
window again.
- 49 -
User’s manual NAVIGON 81xx
TMC Settings
►
In the TRAFFIC INFORMATION window, tap on Options > Traffic.
In the TRAFFIC INFORMATION window you can set the TMC traffic station
and configure whether the reception of a traffic message concerning
your route should affect your route planning and if so how.
Tuning Mode
Tap on Tuning Mode and select a method for selecting the TMC radio
station.
►
►
►
Automatic: You can use the arrow buttons in the station area to
select another station. The system will search for another station if
reception becomes poor.
Hold station: You can use the arrow keys in the station area to
select another station. The system will search for the same station
on a different frequency if the signal becomes poor.
Hold frequency: You can use the arrow keys in the station area to
select another frequency. The system will not search for another
station if reception becomes poor.
Recalculate Route
Tap on Recalculate Route and select how new traffic messages
concerning your route are to be used.
►
►
6.7.5
Automatically: An alternative route will be calculated automatically.
The system will inform you on the recalculation.
On Request: A window opens with information about the location
and type of traffic obstruction. You can then decide whether an
alternative route is to be calculated or not.
Logbook
You can use the NAVIGON 81xx to record a logbook. The logbook is
recorded in the "Logbook.xls" file. You can open the file with Microsoft
Excel. Each recorded trip is added at the bottom of the table as a new
entry.
The first time a trip is recorded, the "Logbook.xls" file will be created in
the "Navigon\Logbook" folder on the memory card in the navigation
device. If you delete or move this file, a new file will be created when
you next record a trip.
Note: Trips are recorded simultaneously in another file which is
compatible with the WISO Sparbuch program. This file is called
"MN7DriversLog.bin". It can also be found in the "Navigon\Logbook"
folder on the memory card in the navigation device.
- 50 -
Navigation
User’s manual NAVIGON 81xx
Recording trips
You can have all trips recorded automatically.
1. Tap in the NAVIGATION window on Options > Settings > Basic
Settings.
2. Set Logbook to Yes.
3. Tap on OK.
Every trip from now on will be recorded until you reset Logbook to No. It
is possible, however, to exclude individual trips from the recording.
Before a trip
If your trips are recorded in the logbook, a window for entering the trip's
key data is opened before navigation starts. You can also decide,
however, not to record the trip in question.
►
If you don't want to record the trip in question, tap on
(Cancel).
- OR –
1. Enter a name for this entry, e.g. "Trip to customerX", in the Logbook
Entry box.
2. Enter the mileage.
3. Tap on Reason for the Trip and select a reason for the trip from the
list of possibilities.
7
Handsfree Module
The hands-free function allows you to use the NAVIGON 81xx as a
hands-free module for your mobile phone.
Opening the hands-free module
►
In the START window, tap on Phone.
- OR –
►
Tap in the navigation application on
(Phone).
The HANDSFREE MODULE window opens.
Operating the hands-free module
You can adjust the volume of the hands-free module independently of
the volume of the navigation system. For details of how to adjust the
volume refer to "Volume" on page 17.
►
Tap on
foreground.
Handsfree Module
(Music) in order to move the MP3 player into the
- 51 -
User’s manual NAVIGON 81xx
►
►
7.1
Tap on
(Navigation) in order to move the navigation
application into the foreground.
Tap on
(Back) in order to close the hands-free module and
return again to the previously opened window.
Connecting to a telephone
The NAVIGON 81xx must be connected to a mobile phone in order for
you to use the telephone functions.
If the NAVIGON 81xx was last connected to the same mobile phone,
the connection will be established without further prompting.
Problems occurring when trying to establish a Bluetooth connection can
have various causes:
►
Bluetooth is dectivated in the hands-free module of the
NAVIGON 81xx.
Activate Bluetooth. Make sure that the NAVIGON 81xx can be
detected by other Bluetooth devices. (Refer to "Bluetooth Function"
on page 56)
►
Bluetooth is deactivated on the mobile phone or it is set to "Hidden".
Activate Bluetooth on your mobile phone. Make sure that your
mobile phone can be detected by other Bluetooth devices
For more details refer to your mobile phone manual.
►
It may be that the NAVIGON 81xx was never connected to your
mobile phone before.
Initiate the connection manually. (Refer to "Connection with Mobile
Phone” page 57)
If the NAVIGON 81xx is still unable to establish a Bluetooth connection
to your mobile phone, contact your mobile phone manufacturer's
customer support.
7.2
Taking a call
When you receive a call, the INCOMING CALL window will open. You will
be asked whether you want to take the call. The name and the number
of the caller will be displayed if this information is available.
►
Tap on Yes if you want to take the call.
The CALL IN PROGRESS window opens.
►
Tap on No if you do not want to take the call.
Note: Play-back of the MP3 player and the navigation instructions are
muted during a call.
- 52 -
Handsfree Module
User’s manual NAVIGON 81xx
7.3
Making a call
With the NAVIGON 81xx you can make a call in various ways:
Note: Play-back of the MP3 player and the navigation instructions are
muted during a call.
7.3.1
Dialling a telephone number
1. Tap on the HANDSFREE MODULE button in the Keyboard window.
2. Enter the desired telephone number.
3. Tap on the Dial a Number button.
7.3.2
Dialling a Speed Call number to call home
You can configure 4 Speed Call buttons.
►
Tap in the HANDSFREE MODULE window on the corresponding
Speed Call button.
Note: If no number has been entered for the Speed Call button selected
or if no Bluetooth connection has been established to a mobile phone,
the MODIFY PRESET window will open.
For more details refer to chapter "Preset" on page 55.
7.3.3
Calling a contact from the phone book
You can select numbers from the phone book of the mobile phone to
which the NAVIGON 81xx is connected.
1. In the HANDSFREE MODULE window, tap on Phone Book.
2. Tap on the contact you want to call.
If more than one phone number is saved for this contact, a list with
all the phone numbers saved for the contact will open.
3. Tap on the number you want to dial.
Note: The phone book is not copied permanently to the navigation
device. It is available to the hands-free module only for as long as it is
connected to the mobile phone.
7.3.4
Calling most recently dialled, received or missed numbers
Note: The RECENT CALLS list contains outgoing, incoming and
unanswered calls. Incoming and unanswered calls can be dialled only
if the caller's number was transmitted.
Handsfree Module
- 53 -
User’s manual NAVIGON 81xx
1. Tap in the HANDSFREE MODULE window on the Recent Calls button.
2. Tap on the entry you want.
Note: The RECENT CALLS list is not copied permanently to the
navigation device. It is available to the hands-free module only for as
long as it is connected to the mobile phone.
7.3.5
Transferring a call from your mobile telephone
The NAVIGON 81xx takes calls automatically from the mobile phone as
soon as a Bluetooth connection is established between the two devices.
7.4
During a call
You are calling using the hands-free module. The CALL IN PROGRESS
window is open.
7.4.1
Moving the navigation application to the foreground
You can move the navigation application to the foreground at any time.
In this way you can have the map in the foreground during a call when
the NAVIGON 81xx is in the process of navigating.
►
Tap on the
(Navigation) button.
While a call is in progress, the
icon (Call in Progress, green mobile
phone) is visible in the top right corner of the display.
►
7.4.2
Tap on the
button (Phone) in order to open the CALL IN
PROGRESS window again.
Entering numbers
You can enter numbers during a call. This may be the case, for
example, if a further connection via a telephone system is necessary.
1. Tap on Keyboard.
2. Enter the desired numbers.
3. Tap on
window.
7.4.3
(Back) in order to open the CALL IN PROGRESS
Transferring a call to the mobile phone
►
In the CALL IN PROGRESS window, tap on Options > Use Mobile
Phone.
Pick up the mobile telephone and continue the call.
- 54 -
Handsfree Module
User’s manual NAVIGON 81xx
7.4.4
Ending the call
►
7.5
Tap in the CALL IN PROGRESS window on the Hang up button in
order to end the call.
Configuring the hands-free function
The hands-free module of the NAVIGON 81xx contains a number of
settings that can be individually configured.
For information about configuring the settings in this window refer to
"Configuring the NAVIGON 81xx" on page 64.
7.5.1
Preset
The hands-free module of the NAVIGON 81xx contains four Speed Call
buttons that can be individually configured.
1. In the HANDSFREE MODULE window, tap on Settings > Preset.
The MODIFY PRESET window opens.
2. Tap on the Speed Call button that you want to edit.
Entering a new Speed Call number or editing an existing Speed
Call number
3. Tap on the Edit button.
4. Enter the name and the number for the selected Speed Call button
or edit the existing name and number.
5. Tap on OK.
Adopting a number from the phone book of the mobile phone
3. Tap on the From Phone Book button. This button is deactivated
when no connection exists to a mobile phone.
4. Tap on the entry you want to adopt for the Speed Call button.
5. Tap on OK.
Deleting a Speed Call number
3. Tap on the Delete button.
4. Confirm that you want to delete the Speed Call number.
The MODIFY PRESET window opens again. No phone number and
no name exist any longer for the selected Speed Call button.
Handsfree Module
- 55 -
User’s manual NAVIGON 81xx
7.5.2
Handsfree Settings
In the HANDSFREE SETTINGS window you can configure the settings for
the phone functions of the hands-free module of your NAVIGON 81xx.
►
In the HANDSFREE MODULE window, tap on Settings > Handsfree
Settings.
The HANDSFREE SETTINGS window opens.
Volume of the Phone Call: The volume of the call can be adjusted
independently of the volume of the navigation application and the MP3
player.
Volume of the Ring Tone: The volume of the ring tone can be adjusted
independently of the volume of the navigation application and the MP3
player.
7.5.3
Bluetooth Function
►
In the HANDSFREE MODULE window, tap on Settings > Bluetooth
Function.
The BLUETOOTH FUNCTION window opens.
Bluetooth Function: Select whether you want to activate the Bluetooth function
(Yes or No).
The hands-free module cannot connect to a mobile phone if the
Bluetooth function is deactivated.
Discoverable by Others: Select whether other Bluetooth-capable devices (in
particular mobile phones) should be able to detect the NAVIGON 81xx
(Yes or No).
Others May Connect: Select whether other devices should be able to initiate a
connection (Yes or No).
Reconnect automatically: Select whether the connection to the last connected
phone is to be restored automatically (Yes or No).
Example: The connection is interrupted as soon as you leave the
vehicle. It can be restored as soon as you approach the vehicle again.
Note: The settings Discoverable by Others, Others May Connect and
Reconnect automatically are effective only when the Bluetooth function
is activated.
Note: A Bluetooth connection can be established from the mobile
phone only when the settings Bluetooth Function, Discoverable by
Others and Reconnect automatically were all selected with Yes.
- 56 -
Handsfree Module
User’s manual NAVIGON 81xx
7.6
Connection with Mobile Phone
Note: The Bluetooth functions of both the NAVIGON 81xx and the
mobile phone must be configured accordingly in order for a Bluetooth
connection to be established between the two devices.
For details of how to configure the NAVIGON 81xx refer to chapter
"Bluetooth Function" on page 56.
For details of how to configure the mobile phone refer to the related
manual.
The NAVIGON 81xx can establish a connection to only one Bluetoothcapable mobile phone.
As a rule the NAVIGON 81xx will automatically establish a connection
to a mobile phone to which it was once connected already. However,
you can also use this function to establish a connection to a different
mobile phone while a connection between the NAVIGON 81xx and a
mobile phone already exists.
7.6.1
Establishing a connection from the navigation device
1. Make sure that the Bluetooth function is activated on both the
mobile phone and the NAVIGON 81xx.
2. In the HANDSFREE MODULE window, tap on Settings > Connection
with Mobile Phone > New Connection.
The navigation device looks for Bluetooth devices and lists all the
devices it recognises.
3. Tap on the name of your mobile phone.
The navigation device prompts you to enter a password.
4. Enter a four-digit password (any digits) in the Key box and tap on
OK.
Your mobile phone prompts you to enter a password.
5. Enter the same password as on the NAVIGON 81xx.
On the NAVIGON 81xx, the SETTINGS BT window opens. A
connection is established between the two devices.
Tap on
window.
7.6.2
(Back) in order to return to the HANDSFREE MODULE
Establishing a connection from the mobile phone
Note: Please consult the mobile phone's manual if you are uncertain
about how to carry out the following steps on the mobile phone.
1. Make sure that the Bluetooth function is activated on both the
mobile phone and the NAVIGON 81xx.
Handsfree Module
- 57 -
User’s manual NAVIGON 81xx
2. Using your mobile phone, search for other Bluetooth devices.
The navigation device is detected as NAVIGON.
3. Initiate a connection to the detected NAVIGON device.
The mobile phone prompts you to enter a password.
4. Enter a four-digit password (user-defined).
The NAVIGON 81xx prompts you to enter a password.
5. Enter the same password in the Key box as on the mobile phone
and tap on OK.
The HANDSFREE MODULE window opens. A connection is
established between the two devices. The name of the connected
mobile phone is displayed at the bottom edge of the screen.
7.6.3
Terminating the connection and deleting the connection
data
You can terminate the connection between the NAVIGON 81xx and the
mobile phone at any time.
Note: You don't need to terminate the connection manually. The
connection is terminated automatically when the mobile phone is moved
a distance of approximately10 m from the NAVIGON 81xx. In this case
the connection data are saved so that the connection can be restored
automatically when the mobile phone is close enough to the
NAVIGON 81xx again.
1. In the SETTINGS BT window, tap on Connection with Mobile
Phone > Clear Connection Data.
You will be prompted to confirm that you want to terminate the
connection.
2. Tap on the OK button.
Note: After the connection is terminated, the NAVIGON 81xx is no
longer able to establish an automatic connection to a mobile phone,
including the same mobile phone as for the last connection.
You must establish the next connection to a mobile phone manually
(refer to chapter "Connection with Mobile Phone" on page 57).
8
Music
The NAVIGON 81xx can play back audio files which have been saved
on the memory card with the navigation application.
Note: Listening to music too long and too loud can damage your
hearing. Do not hold the loudspeaker of the NAVIGON 81xx directly
against your ear!
- 58 -
Music
User’s manual NAVIGON 81xx
8.1
Suitable files
The MP3 player can play back MP3 files and WMA files. Files which are
playback-protected in any way (DRM, Digital Rights Management)
cannot be played back.
8.2
Opening the MP3 player
When the START window is open:
►
Tap on Music.
When the hands-free module or the navigation application is open:
►
Tap on the
(Music) button, which is located at the bottom
edge of many windows.
The MP3 player cannot be opened in the picture viewer or the FM
transmitter.
8.3
Selecting an audio file
►
In the MUSIC window, tap on Folder.
The CURRENT FOLDER opens. The name of the current folder is
indicated at the top. Files and sub-folders are listed underneath. They
are identified as follows:
Audio File: Only those files are shown which can be played back by the
MP3 player. (Refer to "Suitable files" on page 59)
Folder: The sub-folders of the current folder are shown.
►
Tap on a sub-folder in order to open it.
Note: If the sub-folder has no playable audio files or no sub-folders, it
cannot be opened.
►
Tap on
►
Tap on an audio file in order to play it back.
►
Music
(Up one level) in order to open the next higher folder.
Tap on Cancel in order to close the CURRENT FOLDER window
without selecting a file.
- 59 -
User’s manual NAVIGON 81xx
8.4
Operating the MP3 player
Information area
Three music items are always displayed in the information area of the
MUSIC window:
►
Title last played: position of the file in the folder, name of the title,
performer
If no title was played yet, the last title in the current folder will be
shown here.
►
Current title: name of the album, position of the file in the folder,
name of the title, performer, progress and duration
The title that is currently being played back or that will be played
back when you tap on
►
(Play).
Next title: position of the file in the folder, name of the title,
performer
If there is no next title, the first title in the current folder will be
displayed.
If the name of the album and the performer cannot be read out of the
file, they will not be displayed.
If the name of the title cannot be read out of the file, the name of the fille
will be displayed instead.
Controls
Play: Plays back the current title.
Stop: Stops the play-back.
Pause: Interrupts the play-back.
Rewind: Tap briefly: jumps to previous title.
Press and hold: fast rewind in the current title.
Fast forward: Tap briefly: jumps forward to the next title.
Press and hold: fast forward in the current title.
Back: Moves the application from which you opened the MP3 player to
the foreground. If play-back is in progress, it is not terminated.
Play-back mode
The MP3 player plays all titles in the current folder in ascending order.
- 60 -
Music
User’s manual NAVIGON 81xx
Note: When all the titles have been played, play-back will continue from
the beginning. To interrupt the play-back of audio files you must tap on
(Stop) or
►
►
8.5
(Pause).
Tap on
(Shuffle Mode) in order to play back the titles in
random order.
Tap on this button again in order to play back the titles again in
ascending order.
Music in the background
When the MP3 player is playing back an audio file and a different
application is moved to the foreground, the MP3 player behaves as
follows:
Start window
Play-back of the file continues.
Navigation Application in the foreground
Play-back of the file continues. If driving instructions are announced
during navigation, the volume of the MP3 player is lowered for the
duration of the announcement. This does not apply when the volume of
the MP3 player is very low.
Handsfree Module in the foreground
When an incoming call is signalled or when you establish a connection,
play-back of the file is interrupted. It will be continued automatically
when the call has ended.
Picture Viewer in the foreground
Play-back of the file continues.
FM Transmitter in the foreground
Play-back of the file is interrupted only to transmit a test signal; it is then
continued automatically.
9
Pictures
The NAVIGON 81xx can display image files which are saved on the
memory card with the navigation software.
Pictures
- 61 -
User’s manual NAVIGON 81xx
9.1
Suitable files
The picture viewer can show JPG files, PNG files and GIF files (no
animated GIF files).
9.2
Opening the picture viewer
You can open the picture viewer only from the START window.
►
9.3
Tap on Pictures.
Selecting an image file
►
In the PICTURES window, tap on Folder.
The CURRENT FOLDER opens. The name of the current folder is
indicated at the top. Files and sub-folders are listed underneath. They
are identified as follows:
Picture File: Only those files are listed which can be shown by the
picture viewer. (Refer to "Suitable files" on page 59)
Folder: Sub-folders of the current folder are displayed.
►
Tap on a sub-folder in order to open it.
Note: If the sub-folder contains no suitable image files or sub-folders, it
cannot be opened.
►
Tap on
►
Tap on an image file in order to show it.
►
9.4
(Up one level) in order to open the next higher folder.
Tap on Cancel in order to close the CURRENT FOLDER window
without selecting a file.
Operating the picture viewer
Information area
The current image file and its file name are displayed in the information
area in the PICTURES window.
Controls
Full Screen: Shows the current picture as large as possible.
Next: Loads the next picture in the current folder.
Previous: Loads the previous picture in the current folder.
- 62 -
Pictures
User’s manual NAVIGON 81xx
Slide Show: Shows all the pictures in the current folder one after the
other.
Exit: Closes the picture viewer.
9.5
Play-back mode
From the PICTURES window you can start two play-back modes.
Full Screen
►
Tap on
(Full Screen).
The picture is scaled to its maximum size. You can use the
button (Next) and the
button (Previous) to switch to the other
pictures in the current folder.
►
Tap on the picture in order to close complete picture mode.
Slide Show
►
Tap on
(Slide Show).
Starting with the current picture, all the pictures in the current folder are
shown for several seconds one after the other. The pictures are scaled
to their maximum size. When all the pictures in the current folder have
been shown, the presentation continues from the beginning.
►
10
Tap on the middle of the picture in order to close the show again.
FM Transmitter
With the FM transmitter you can listen to all audio outputs from the
NAVIGON 81xx over the loudspeakers of the car radio. This applies to
the navigation instructions, music from the MP3 player and phone calls
with the hands-free module.
Caution! Operation of the FM transmitter is not allowed in the following
countries:
France, Greece, Italy, Ireland, Latvia, Malta, Norway, Slovakia, Hungary
and Cyprus.
Caution! Before you use the FM transmitter in another country, find out
about the regulations in force there. In some countries it is against the
law to operate FM transmitters.
The FM transmitter is operated via the options in the START window.
FM Transmitter
- 63 -
User’s manual NAVIGON 81xx
Switching on the FM transmitter
1. In the START window, tap on Options > FM Transmitter.
2. Tap on On.
3. Follow the instructions on the screen.
Note: The frequency selected in the FM TRANSMITTER window must be
set on the car radio. The navigation device must not be too far from the
vehicle antenna because the FM transmitter has a transmission range
of only a few metres.
Switching off the FM transmitter
1. In the START window, tap on Options > FM Transmitter.
2. Tap on Off.
10.1
Configuring the FM transmitter
►
In the FM TRANSMITTER window, tap on Options > Settings FM.
The SETTINGS FM window opens.
Standard: Select the settings to be used by the FM transmitter for transmission
(Europe or USA).
Caution! These standards differ, for example in the powers of
transmission they define. Please note that you are not permitted to
transmit with the USA setting in the countries of the European Union.
11
Configuring the NAVIGON 81xx
The SETTINGS window is the point from which you can start customising
the NAVIGON 81xx to match your personal preferences.
Settings can be accessed via the options in the START window and via
the options in many windows of the navigation application.
►
Tap on Options > Settings.
The SETTINGS window of the navigation application has several buttons:
Current Map, POI, Basic Settings and Route Profile.
►
Tap on a button to open the corresponding settings window.
The settings of the individual windows are distributed over several
screen pages. You can toggle between these pages with the
(To the Left) button and the
- 64 -
(To the Right) button.
Configuring the NAVIGON 81xx
User’s manual NAVIGON 81xx
Some settings can have only one of two values. These settings can be
recognised by the
(Toggle button). All possible values are visible.
The currently valid value is highlighted in white.
►
Tap on
values.
(Toggle) in order to switch between the possible
Some settings can accept several different values. These settings can
be recognised by the
visible.
1. Tap on
(List) button. The currently valid value is
(List).
A list with all possible values opens. The currently valid value is
marked.
2. Tap on the value you want. It is now marked.
3. Tap on OK.
The list closes. The new value is indicated.
For each setting there is a
(Help) button. When you tap on it you
will see an exact definition of the setting in question.
You can close the settings windows in two ways:
►
Tap on OK.
►
Tap Cancel.
Any changes you have made will be adopted.
Any changes you have made will not be adopted.
Configuring the NAVIGON 81xx
- 65 -
User’s manual NAVIGON 81xx
12
Appendix
12.1
Technical data
Dimensions
Weight
Operating
conditions
134.5 x 84.4 x 21.9 mm
approx. 265 g
Operating
temperature
Storage
temperature
Humidity
CPU
Operating system
Display
Memory
ROM
RAM
GPS
TMC
FM Transmitter
Device keys
I/O
Power supply
Rechargeable
battery
Charging
Mains adapter
Car charger
cable
- 66 -
Stylus
Keyboard
Loudspeaker
Microphone
Headset
Memory card
USB
Bluetooth
-10°C to 60°C (14°F to 140°F)
-30°C to 70°C (-22°F to 158°F)
0% to 90%, non-precipitating
Samsung 2443-533Mhz
Microsoft Windows CE 5.0
4.8" LCD colour display with resistive
touch-panel
480 x 272 pixels (WQVGA)
Landscape format, transmissive
512 MB
128 MB
Yes (SiRF GPS III, 20 channels)
Built-in antenna
Socket for external antenna
Yes
Yes
5 (On/Off, Back, Quieter, Louder,
Volume on/off)
Plastic stylus
Software keyboard
Yes
Yes
3.5 mm phone jack
SD, SDHC, MMC
USB 2 0
Integrated (CSR Bluecore 4)
Via USB socket or via cradle
Type
Li-Ion, 1500 mAh
Electronic
Duration
Input
Output
Operating
temperature
Input
Output
Operating
temperature
Integrated
approx. 4-5 hours
100-240V ~ (alternating current, AC)
1A, 5V = (direct current, DC)
0°C to 40°C (32°F to 104°F)
10-30V = (direct current, DC)
1A, 5V = (direct current, DC)
-10°C to 60°C (14°F to 140°F)
Appendix
User’s manual NAVIGON 81xx
12.2
Identification and serial number
The navigation device has various identification labels underneath the
rear cover (e.g. CE label, serial number, ...)
If you need to see any of these labels, proceed as follows:
1. Switch off the navigation device.
2. Take the stylus and the memory card out of the device.
3. With your thumbnail in the slot on the bottom of the device, pull the
rear cover off the device.
To close the rear cover again:
1. Place the cover correctly in position.
2. Push the cover firmly against the device until it latches home in all
corners.
3. Re-insert the stylus and the memory card.
Note: We recommend that you remove the rear cover only when told to
do so by our service staff.
12.3
Declaration of conformity
The NAVIGON 81xx device described in this manual bears the
following labels:
It is authorised for operation in the countries of the European Union,
Switzerland, Norway and the countries of North America.
NAVIGON AG declares herewith that the NAVIGON 81xx device
conforms with the Radio & Telecommunication Terminal Equipment
Directive (R&TTE) (1999/5/EEC).
The direction of conformity can be found at the following Internet
address:
http://navigonuk.custhelp.com/cgibin/navigonuk.cfg/php/enduser/std_adp.php?p_faqid=222
The manufacturer is not liable for modifications made by the user which
may alter the device's conformity with the CE label, nor for the
consequences thereof.
Appendix
- 67 -
User’s manual NAVIGON 81xx
13
Troubleshooting
In this chapter you will find solutions to problems which may arise
during use of the NAVIGON 81xx.
This list does not claim to be complete. Answers to many other
questions can be found on the NAVIGON AG website. (See "Questions
about the product" on page 7)
I have connected a charger to the NAVIGON 81xx. A connection to a
computer is shown on the display.
or
I have connected the NAVIGON 81xx to a computer but it is not detected
as a removable disc.
The USB connector of the charger is not fully inserted in the case.
1. Unplug the connector.
The navigation device will carry out a new start. Wait for the
software to be reloaded.
2. Without delay, insert the USB connector from the charger into the
corresponding socket of the NAVIGON 81xx as far as it will go.
(See "Description of the NAVIGON 81xx" on page 8)
The USB connector is not connected correctly. See above.
I have changed the language for the use interface and now there are
different buttons in the Navigation window.
The Voice Command function is not available for every language.
In the languages for which this function is not available, the Voice
Command button is replaced by the Show Map button.
I am not receiving any navigation instructions.
or
I want to listen to music but am getting no sound.
Possible causes and their remedies:
►
The FM transmitter is in operation but the car radio is off or tuned to
a different frequency.
Switch off the FM transmitter. (See "FM Transmitter" on page 63)
►
The NAVIGON 81xx is muted.
Press the
(Volume on/off) key. (See "Description of the
NAVIGON 81xx" on page 8)
- 68 -
Troubleshooting
User’s manual NAVIGON 81xx
The software does not respond any longer. The screen is frozen.
or
The software responds strangely to my entries.
Carry out a device reset. All the internal components of the navigation
device will be reset as the result.
1. With the
(On/Off) key pressed and held, press the
key
simultaneously. (This key is countersunk. Use the stylus or a paperclip.)
The device will switch off. Wait a few seconds.
2. Press the
again.
(On/Off) key in order to switch the device back on
The software will now be reloaded. As soon as the START window
appears, you can use the device again.
The navigation device won't switch on.
Possible causes and their remedies:
►
The navigation device hasn't been used for a long time. The battery
is flat.
Charge the battery of the NAVIGON 81xx for a few minutes before
you switch it on.
►
The navigation device is very cold.
Insert the NAVIGON 81xx into the cradle. Make sure that the power
supply is connected before you switch on the device.
I want to dial a number from the phone book of my mobile phone with the
NAVIGON 81xx. The mobile phone tells me that the data transmission was
successful but the NAVIGON 81xx is still not ready to dial.
The NAVIGON 81xx has to convert as well as import the data. This can
take a lot of time particularly with large phone books.
You can also dial the number with the mobile phone and then transfer
the call to the NAVIGON 81xx. (Refer to "Transferring a call from your
mobile telephone" on page 54)
Troubleshooting
- 69 -
User’s manual NAVIGON 81xx
14
Index
in a Town.................................. 28
Nationwide ............................... 28
Nearby...................................... 27
Save ............................................. 33
Start Navigation ............................ 32
Take Me Home ....................... 31, 34
Turn-by-Turn List .......................... 33
B
Block............................................ 44, 48
Bluetooth ........... see Handsfree Module
Bluetooth Function ............................ 56
C
Call
Dial a Number ............................... 53
Phone Book .................................. 53
Preset ........................................... 53
Recent Calls ................................. 53
Call in Progress
Enter numerals ............................. 54
Hang up ........................................ 54
Show Map ..................................... 54
Use handsfree .............................. 54
Use Mobile Phone ........................ 54
Compass ........................................... 18
Configuration ..................................... 64
Connection with Mobile Phone
Clear Connection Data ................. 58
Connection with Mobile Phone.... 52, 56
Contacts ............................................ 31
Conventions followed in this
manual .............................................. 6
Current Position
Save.............................................. 47
D
Data entry.......................................... 22
Destination
Address......................................... 25
Contacts........................................ 31
Direct Access................................ 29
Favourites ..................................... 30
From Map ..................................... 32
Home Address ........................ 31, 34
Input Sequence............................. 25
Last Destinations .......................... 30
My Destinations ............................ 24
New Destination............................ 24
POI................................................ 27
- 70 -
E
Emergency Services ................... 38, 47
Energy................................... 11, 13, 19
Entering data..................................... 22
F
Factory Settings ................................ 16
Favourites ................................... 30, 33
FM Transmitter
Activate......................................... 63
Deactivate..................................... 63
Symbols ........................................ 20
G
GPS
Faulty reception ............................ 23
Initialise......................................... 23
Signals.......................................... 14
Symbols ........................................ 18
GPS Status ....................................... 47
H
Handsfree Module
Bluetooth Function........................ 56
Call ............................................... 52
Call in Progress ............................ 54
Clear Connection Data ................. 58
Connection with Mobile
Phone................................... 52, 56
Dial a Number............................... 53
Enter numerals ............................. 54
Handsfree Settings ....................... 55
Hang up ........................................ 54
Index
User’s manual NAVIGON 81xx
Incoming Call ................................ 52
Open ............................................. 51
Phone Book .................................. 53
Preset ..................................... 53, 55
Recent Calls ................................. 53
Settings ......................................... 54
Show Map ..................................... 54
Symbols ........................................ 19
Use handsfree .............................. 54
Use Mobile Phone ........................ 54
Volume.......................................... 51
Handsfree Settings............................ 55
Home Address............................. 31, 34
Hotline ................................................. 7
N
Keyboard ........................................... 20
Navigation
Block....................................... 44, 48
Interim Destination........................ 44
No GPS .................................. 33, 38
POI ............................................... 44
POI on Your Route ....................... 44
Route Profile........................... 32, 37
Skip Route Point........................... 44
Start ........................................ 32, 37
Turn-by-Turn List .................... 33, 38
Navigation Application
Exit................................................ 23
Start .............................................. 23
NAVIGON 81xx
Description...................................... 8
Energy .................................... 11, 13
Installation .................................... 13
Memory card................................. 12
Scope of Delivery ........................... 7
Start .............................................. 15
TMC .............................................. 13
New Destination ................................ 24
L
O
Last Destinations......................... 30, 33
Logbook............................................. 50
Options.................................. 15, 22, 38
I
Input Sequence ................................. 25
Interim Destination ............................ 44
K
M
Manual
Conventions .................................... 6
Symbols .......................................... 6
Map
Destination search ........................ 45
Navigation..................................... 41
Preview ......................................... 40
Reality View .................................. 44
Memory card ..................................... 12
Menu ................................................. 22
MP3 Player........................................ 58
Music ................................................. 58
Muting................................................ 20
My Destinations................................. 24
Index
P
Password Lock.................................. 16
Phone................ see Handsfree Module
Phone Book....................................... 53
Picture Viewer ................................... 61
Pictures ............................................. 61
POI
Direct Access................................ 29
in a Town ...................................... 28
Nationwide.................................... 28
Nearby .......................................... 27
On route........................................ 44
Preset................................................ 55
Product Information........................... 16
- 71 -
User’s manual NAVIGON 81xx
R
Reality View....................................... 44
Recalculate Route ............................. 50
Recent Calls ...................................... 53
Route Planning.................................. 34
Route points
Add ............................................... 35
Delete ........................................... 36
Order............................................. 36
Starting Point ................................ 35
Route Profile................................ 32, 37
Routes
Manage ......................................... 36
Planning........................................ 34
Route points.................................. 35
Route Profile ................................. 37
Save.............................................. 36
Show............................................. 37
Simulation ..................................... 37
Start Navigation ............................ 37
Starting Point ................................ 34
Turn-by-Turn List .......................... 38
S
Safety information ............................... 8
Scope of Delivery ................................ 7
Service ................................................ 7
Settings
Configuration ................................ 64
Volume.................................... 17, 43
Settings Handsfree Module
Bluetooth Function........................ 56
Clear Connection Data ................. 58
Connection with Mobile
Phone ......................................... 56
Handsfree Settings ....................... 55
Preset ........................................... 55
Volume.......................................... 51
- 72 -
Simulation
Exit................................................ 37
Start .............................................. 37
Skip Route Point ............................... 44
Software keyboard ............................ 20
Support................................................ 7
Symbols used in this manual .............. 6
T
Take Me Home............................ 31, 34
TMC
Recalculate Route ........................ 50
Show............................................. 49
Symbols ........................................ 18
Tuning Mode................................. 50
TMC Settings
Recalculate Route ........................ 50
TMC .............................................. 49
Traffic Information......................... 49
Tuning Mode................................. 50
Touchscreen Calibration ................... 16
Trade marks ........................................ 7
Traffic Information
Recalculate Route ........................ 50
Show............................................. 49
Tuning Mode................................. 50
Troubleshooting ................................ 68
Tuning Mode ..................................... 50
Turn-by-Turn List
Block............................................. 48
Show................................. 33, 38, 48
V
Volume .................................. 17, 43, 51
W
Warranty.............................................. 6
Index
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement