IdeaPad S205 Hardware Maintenance Manual

IdeaPad S205 Hardware Maintenance Manual
IdeaPad S205
Hardware
Maintenance
Manual
Note:
Before using this information and the product it supports, be sure to read the general information under
“Notices” on page 76.
First Edition (December 2010)
© Copyright Lenovo 2010. All rights reserved.
LENOVO products, data, computer software, and services have been developed exclusively at
private expense and are sold to governmental entities as commercial items as defined by 48 C.F.R.
2.101 with limited and restricted rights to use, reproduction and disclosure.
LIMITED AND RESTRICTED RIGHTS NOTICE: If products, data, computer software, or services
are delivered pursuant a General Services Administration ″GSA″ contract, use, reproduction, or
disclosure is subject to restrictions set forth in Contract No. GS-35F-05925.
© 2010 Lenovo
Contents
About this manual........................................ iv
Safety information......................................... 1
General safety................................................. 2
Electrical safety............................................... 3
Safety inspection guide................................... 5
Handling devices that are sensitive to
electrostatic discharge..................................... 6
Grounding requirements.................................. 6
Safety notices: multilingual translations.......... 7
Laser compliance statement......................... 14
Important service information.................... 16
Strategy for replacing FRUs.......................... 16
Strategy for replacing a hard disk drive.............17
Important notice for replacing a system
board ................................................................17
Important information about replacing RoHS
compliant FRUs............................................. 18
General checkout ....................................... 19
What to do first.............................................. 20
Power system checkout................................ 21
Checking the AC adapter . ................................21
Checking operational charging..........................21
Checking the battery pack ................................22
1060 PCI Express Mini Card for
wireless LAN......................................................42
1070 LCD unit....................................................44
1080 Hard disk drive (HDD)..............................46
1090 DIMM........................................................47
1100 Fan assembly and heat sink assembly.....48
1110 System board............................................. 50
1120 Speakers...................................................53
1130 Bluetooth card...........................................54
1140 LCD front bezel.........................................55
1150 LCD panel, LCD cable and hinges...........56
1160 Integrated camera.....................................58
1170 Antenna assembly and LCD cover ..........59
Locations....................................................... 60
Front view..........................................................60
Right-side view..................................................61
Bottom and Left-side view ................................61
Parts list......................................................... 62
Overall...............................................................63
LCD FRUs.........................................................67
Keyboard...........................................................69
Miscellaneous parts...........................................71
AC adapters.......................................................72
Power cords.......................................................73
Notices......................................................... 76
Trademarks................................................... 77
Related service information....................... 23
Restoring the factory contents by using
OneKey Recovery......................................... 23
Restore of factory default..................................23
Using recovery discs.........................................23
Passwords..................................................... 24
Power-on password...........................................24
Supervisor password ........................................24
Power management...................................... 25
Screen blank mode............................................25
Sleep (standby) mode.......................................25
Hibernation mode..............................................26
Lenovo IdeaPad S205................................. 27
Specifications................................................ 27
Status indicators............................................ 29
Fn key combinations..................................... 31
FRU replacement notices.............................. 32
Screw notices ...................................................32
Removing and replacing an FRU.................. 33
1010 Battery pack..............................................34
1020 Dummy card.............................................35
1030 SIM card...................................................36
1040 Keyboard..................................................37
1050 Base cover................................................39
iii
About this manual
This manual contains service and reference information for the following
Lenovo IdeaPad product:
Lenovo IdeaPad S205
Use this manual to troubleshoot problems.
The manual is divided into the following sections:
•• The common sections provide general information, guidelines, and safety
information required for servicing computers.
•• The product-specific section includes service, reference, and product-specific
parts information.
Important:
This manual is intended only for trained servicers who are familiar with Lenovo
IdeaPad products. Use this manual to troubleshoot problems effectively.
Before servicing a Lenovo IdeaPad product, make sure to read all the information
under “Safety information” on page 1 and “Important service information” on
page 16.
iv
Safety information
Safety information
This chapter presents the following safety information that you need to get
familiar with before you service an IdeaPad S205 computer:
•• “General safety” on page 2
•• “Electrical safety” on page 3
•• “Safety inspection guide” on page 5
•• “Handling devices that are sensitive to electrostatic discharge” on page 6
•• “Grounding requirements” on page 6
•• “Safety notices: multilingual translations” on page 7
•• “Laser compliance statement” on page 14
1
IdeaPad S205 Hardware Maintenance Manual
General safety
Follow these rules below to ensure general safety:
•• Observe a good housekeeping in the area where the machines are put
during and after the maintenance.
•• When lifting any heavy object:
1. Make sure that you can stand safely without slipping.
2. Distribute the weight of the object equally between your feet.
3. Use a slow lifting force. Never move suddenly or twist when you attempt
to lift it.
4. Lift it by standing or pushing up with your leg muscles; this action could
avoid the strain from the muscles in your back. Do not attempt to lift any
object that weighs more than 16 kg (35 lb) or that you think is too heavy
for you.
•• Do not perform any action that causes hazards to the customer, or that
makes the machine unsafe.
•• Before you start the machine, make sure that other service representatives
and the customer are not in a hazardous position.
•• Place removed covers and other parts in a safe place, keeping them away
from all personnel, while you are servicing the machine.
•• Keep your toolcase away from walk areas so that other people will not trip it
over.
•• Do not wear loose clothing that can be trapped in the moving parts of the
machine. Make sure that your sleeves are fastened or rolled up above your
elbows. If your hair is long, fasten it.
•• Insert the ends of your necktie or scarf inside clothing or fasten it with the
nonconductive clip, about 8 centimeters (3 inches) from the end.
•• Do not wear jewelry, chains, metal-frame eyeglasses, or metal fasteners for
your clothing.
Attention: Metal objects are good electrical conductors.
•• Wear safety glasses when you are hammering, drilling, soldering, cutting
wire, attaching springs, using solvents, or working in any other conditions
that may be hazardous to your eyes.
•• After service, reinstall all safety shields, guards, labels, and ground wires.
Replace any safety device that is worn or defective.
•• Reinstall all covers correctly before returning the machine to the customer.
•• Fan louvers on the machine help to prevent the overheating of internal
components. Do not obstruct fan louvers or cover them with labels or
stickers.
2
Safety information
Electrical safety
Observe the following rules when working on electrical equipments.
Important:
Use only approved tools and test equipments. Some hand tools have handles
covered with a soft material that does not insulate you when working with live
electrical currents.
Many customers have rubber floor mats near their machines that contain small
conductive fibers to decrease electrostatic discharges. Do not use such kind of mat
to protect yourself from electrical shock.
•• Find the room emergency power-off (EPO) switch, disconnecting the switch
or electrical outlet. If an electrical accident occurs, you can then operate the
switch or unplug the power cord quickly.
•• Do not work alone under hazardous conditions or near the equipment that
has hazardous voltages.
•• Disconnect all power before:
– Performing a mechanical inspection
– Working near power supplies
– Removing or installing main units
•• Before you start to work on the machine, unplug the power cord. If you
cannot unplug it, ask the customer to power-off the wall box that supplies
power to the machine, and to lock the wall box in the off position.
•• If you need to work on a machine that has exposed electrical circuits,
observe the following precautions:
– Ensure that another person, familiar with the power-off controls, is near
you.
Attention: Another person must be there to switch off the power, if
necessary.
– Use only one hand when working with powered-on electrical equipment;
keep the other hand in your pocket or behind your back.
Attention: An electrical shock can occur only when there is a complete
circuit. By observing the above rule, you may prevent a current from
passing through your body.
– When using testers, set the controls correctly and use the approved
probe leads and accessories for that tester.
– Stand on suitable rubber mats (obtained locally, if necessary) to insulate
you from grounds such as metal floor strips and machine frames.
Observe the special safety precautions when you work with very high voltages;
instructions for these precautions are in the safety sections of maintenance
information. Be extremely careful when you measure the high voltages.
•• Regularly inspect and maintain your electrical hand tools for safe operational
condition.
•• Do not use worn or broken tools and testers.
•• Never assume that power has been disconnected from a circuit. First, check
it to make sure that it has been powered off.
3
IdeaPad S205 Hardware Maintenance Manual
•• Always look carefully for possible hazards in your work area. Examples of
these hazards are moist floors, nongrounded power extension cables, power
surges, and missing safety grounds.
•• Do not touch live electrical circuits with the reflective surface of a plastic
dental mirror. The surface is conductive; such touching can cause personal
injury and machine damage.
•• Do not service the following parts with the power on when they are removed
from their normal operating places in a machine:
– Power supply units
– Pumps
– Blowers and fans
– Motor generators
and similar units. (This practice ensures correct grounding of the units.)
•• If an electrical accident occurs:
– Caution: do not become a victim yourself.
– Switch off the power.
– Send the victim to get medical aid.
4
Safety information
Safety inspection guide
The purpose of this inspection guide is to assist you in identifying potential
unsafe conditions. As each machine was designed and built, required safety
items were installed to protect users and service personnel from injury. This
guide addresses only those items. You should use good judgment to identify
potential safety hazards according to the attachment of non-Lenovo IdeaPad
features or options not covered by this inspection guide.
If any unsafe conditions are present, you must determine how serious the
apparent hazard could be and whether you can continue without first correcting
the problem.
Consider these conditions and the safety hazards they present:
•• Electrical hazards, especially primary power (primary voltage on the frame
can cause serious or fatal electrical shock)
•• Explosive hazards, such as a damaged CRT face or a bulging capacitor
•• Mechanical hazards, such as loose or missing hardware
To determine whether there are any potential unsafe conditions, use the
following checklist at the beginning of every service task. Begin the checks with
the power off, and the power cord disconnected.
Checklist:
1. Check exterior covers for damage (loose, broken, or sharp edges).
2. Turn off the computer. Disconnect the power cord.
3. Check the power cord for:
a. A third-wire ground connector in good condition. Use a meter to measure
third-wire ground continuity for 0.1 ohm or less between the external
ground pin and the frame ground.
b. The power cord should be the type specified in the parts list.
c. Insulation must not be frayed or worn.
4. Check for cracked or bulging batteries.
5. Remove the cover.
6. Check for any obvious non-Lenovo IdeaPad alterations. Use good judgment
as to the safety of any non-Lenovo IdeaPad alterations.
7. Check inside the unit for any obvious unsafe conditions, such as metal
filings, contamination, water or other liquids, or signs of fire or smoke
damage.
8. Check for worn, frayed, or pinched cables.
9. Check that the power-supply cover fasteners (screws or rivets) have not
been removed or tampered with.
5
IdeaPad S205 Hardware Maintenance Manual
Handling devices that are sensitive to electrostatic discharge
Any computer part containing transistors or integrated circuits (ICs) should be
considered sensitive to electrostatic discharge (ESD). ESD damage can occur
when there is a difference in charge between objects. Protect against ESD
damage by equalizing the charge so that the machine, the part, the work mat,
and the person handling the part are all at the same charge.
Notes:
1. Use product-specific ESD procedures when they exceed the requirements
noted here.
2. Make sure that the ESD protective devices you use have been certified (ISO
9000) as fully effective.
When handling ESD-sensitive parts:
•• Keep the parts in protective packages until they are inserted into the product.
•• Avoid contact with other people.
•• Wear a grounded wrist strap against your skin to eliminate static on your
body.
•• Prevent the part from touching your clothing. Most clothing is insulative and
retains a charge even when you are wearing a wrist strap.
•• Use the black side of a grounded work mat to provide a static-free work
surface. The mat is especially useful when handling ESD-sensitive devices.
•• Select a grounding system, such as those listed below, to provide protection
that meets the specific service requirement.
Note:
The use of a grounding system to guard against ESD damage is desirable but not
necessary.
– Attach the ESD ground clip to any frame ground, ground braid, or greenwire ground.
– When working on a double-insulated or battery-operated system, use an
ESD common ground or reference point. You can use coax or connectoroutside shells on these systems.
– Use the round ground prong of the ac plug on ac-operated computers.
Grounding requirements
Electrical grounding of the computer is required for operator safety and correct
system function. Proper grounding of the electrical outlet can be verified by a
certified electrician.
6
Safety information
Safety notices: multilingual translations
The safety notices in this section are provided in English, French, German,
Hebrew, Italian, Japanese, and Spanish.
Safety notice 1
Before the computer is powered on after FRU replacement, make sure all screws,
springs, and other small parts are in place and are not left loose inside the
computer. Verify this by shaking the computer and listening for rattling sounds.
Metallic parts or metal flakes can cause electrical shorts.
Avant de remettre l’ordinateur sous tension après remplacement d’une unité en
clientèle, vérifiez que tous les ressorts, vis et autres pièces sont bien en place et
bien fixées. Pour ce faire, secouez l’unité et assurez-vous qu’aucun bruit suspect
ne se produit. Des pièces métalliques ou des copeaux de métal pourraient causer
un court-circuit.
Bevor nach einem FRU-Austausch der Computer wieder angeschlossen wird,
muß sichergestellt werden, daß keine Schrauben, Federn oder andere Kleinteile
fehlen oder im Gehäuse vergessen wurden. Der Computer muß geschüttelt und auf
Klappergeräusche geprüft werden. Metallteile oder-splitter können Kurzschlüsse
erzeugen.
Prima di accendere l’elaboratore dopo che é stata effettuata la sostituzione di una
FRU, accertarsi che tutte le viti, le molle e tutte le altri parti di piccole dimensioni
siano nella corretta posizione e non siano sparse all’interno dell’elaboratore.
Verificare ciò scuotendo l’elaboratore e prestando attenzione ad eventuali rumori;
eventuali parti o pezzetti metallici possono provocare cortocircuiti pericolosi.
Antes de encender el sistema despues de sustituir una FRU, compruebe que
todos los tornillos, muelles y demás piezas pequeñas se encuentran en su sitio
y no se encuentran sueltas dentro del sistema. Compruébelo agitando el sistema
y escuchando los posibles ruidos que provocarían. Las piezas metálicas pueden
causar cortocircuitos eléctricos.
7
IdeaPad S205 Hardware Maintenance Manual
Safety notice 2
DANGER
Some standby batteries contain a small amount of nickel and cadmium. Do not
disassemble a standby battery, recharge it, throw it into fire or water, or shortcircuit it. Dispose of the battery as required by local ordinances or regulations.
Use only the battery in the appropriate parts listing. Use of an incorrect battery can
result in ignition or explosion of the battery.
Certaines batteries de secours contiennent du nickel et du cadmium. Ne les
démontez pas, ne les rechargez pas, ne les exposez ni au feu ni à l’eau. Ne
les mettez pas en court-circuit. Pour les mettre au rebut, conformez-vous à la
réglementation en vigueur. Lorsque vous remplacez la pile de sauvegarde ou celle
de l’horloge temps réel, veillez à n’utiliser que les modèles cités dans la liste de
pièces détachées adéquate. Une batterie ou une pile inappropriée risque de prendre
feu ou d’exploser.
Die Bereitschaftsbatterie, die sich unter dem Diskettenlaufwerk befindet,
kann geringe Mengen Nickel und Cadmium enthalten. Sie darf nicht zerlegt,
wiederaufgeladen, kurzgeschlossen, oder Feuer oder Wasser ausgesetzt werden.
Bei der Entsorgung die örtlichen Bestimmungen für Sondermüll beachten. Beim
Ersetzen der Bereitschafts-oder Systembatterie nur Batterien des Typs verwenden,
der in der Ersatzteilliste aufgeführt ist. Der Einsatz falscher Batterien kann zu
Entzündung oder Explosion führen.
Alcune batterie di riserva contengono una piccola quantità di nichel e cadmio.
Non smontarle, ricaricarle, gettarle nel fuoco o nell’acqua né cortocircuitarle.
Smaltirle secondo la normativa in vigore (DPR 915/82, successive disposizioni e
disposizioni locali). Quando si sostituisce la batteria dell’RTC (real time clock) o
la batteria di supporto, utilizzare soltanto i tipi inseriti nell’appropriato Catalogo
parti. L’impiego di una batteria non adatta potrebbe determinare l’incendio o
l’esplosione della batteria stessa.
Algunas baterías de reserva contienen una pequeña cantidad de níquel y cadmio.
No las desmonte, ni recargue, ni las eche al fuego o al agua ni las cortocircuite.
Deséchelas tal como dispone la normativa local. Utilice sólo baterías que se
encuentren en la lista de piezas. La utilización de una batería no apropiada puede
provocar la ignición o explosión de la misma.
8
Safety information
Safety notice 3
DANGER
The battery pack contains small amounts of nickel. Do not disassemble it, throw
it into fire or water, or short-circuit it. Dispose of the battery pack as required by
local ordinances or regulations. Use only the battery in the appropriate parts listing
when replacing the battery pack. Use of an incorrect battery can result in ignition
or explosion of the battery.
La batterie contient du nickel. Ne la démontez pas, ne l’exposez ni au feu ni à l’eau.
Ne la mettez pas en court-circuit. Pour la mettre au rebut, conformez-vous à la
réglementation en vigueur. Lorsque vous remplacez la batterie, veillez à n’utiliser
que les modèles cités dans la liste de pièces détachées adéquate. En effet, une
batterie inappropriée risque de prendre feu ou d’exploser.
Akkus enthalten geringe Mengen von Nickel. Sie dürfen nicht zerlegt,
wiederaufgeladen, kurzgeschlossen, oder Feuer oder Wasser ausgesetzt werden.
Bei der Entsorgung die örtlichen Bestimmungen für Sondermüll beachten. Beim
Ersetzen der Batterie nur Batterien des Typs verwenden, der in der Ersatzteilliste
aufgeführt ist. Der Einsatz falscher Batterien kann zu Entzündung oder Explosion
führen.
La batteria contiene piccole quantità di nichel. Non smontarla, gettarla nel fuoco
o nell’acqua né cortocircuitarla. Smaltirla secondo la normativa in vigore (DPR
915/82, successive disposizioni e disposizioni locali). Quando si sostituisce la
batteria, utilizzare soltanto i tipi inseriti nell’appropriato Catalogo parti. L’impiego
di una batteria non adatta potrebbe determinare l’incendio o l’esplosione della
batteria stessa.
Las baterías contienen pequeñas cantidades de níquel. No las desmonte, ni
recargue, ni las eche al fuego o al agua ni las cortocircuite. Deséchelas tal como
dispone la normativa local. Utilice sólo baterías que se encuentren en la lista de
piezas al sustituir la batería. La utilización de una batería no apropiada puede
provocar la ignición o explosión de la misma.
9
IdeaPad S205 Hardware Maintenance Manual
Safety notice 4
DANGER
The lithium battery can cause a fire, an explosion, or a severe burn. Do not
recharge it, remove its polarized connector, disassemble it, heat it above 100°C
(212°F), incinerate it, or expose its cell contents to water. Dispose of the battery as
required by local ordinances or regulations. Use only the battery in the appropriate
parts listing. Use of an incorrect battery can result in ignition or explosion of the
battery.
La pile de sauvegarde contient du lithium. Elle présente des risques d’incendie,
d’explosion ou de brûlures graves. Ne la rechargez pas, ne retirez pas son
connecteur polarisé et ne la démontez pas. Ne l’exposez pas à une temperature
supérieure à 100°C, ne la faites pas brûler et n’en exposez pas le contenu à l’eau.
Mettez la pile au rebut conformément à la réglementation en vigueur. Une pile
inappropriée risque de prendre feu ou d’exploser.
Die Systembatterie ist eine Lithiumbatterie. Sie kann sich entzünden, explodieren
oder schwere Verbrennungen hervorrufen. Batterien dieses Typs dürfen nicht
aufgeladen, zerlegt, über 100 C erhitzt oder verbrannt werden. Auch darf ihr
Inhalt nicht mit Wasser in Verbindung gebracht oder der zur richtigen Polung
angebrachte Verbindungsstecker entfernt werden. Bei der Entsorgung die örtlichen
Bestimmungen für Sondermüll beachten. Beim Ersetzen der Batterie nur Batterien
des Typs verwenden, der in der Ersatzteilliste aufgeführt ist. Der Einsatz falscher
Batterien kann zu Entzündung oder Explosion führen.
La batteria di supporto e una batteria al litio e puo incendiarsi, esplodere o
procurare gravi ustioni. Evitare di ricaricarla, smontarne il connettore polarizzato,
smontarla, riscaldarla ad una temperatura superiore ai 100 gradi centigradi,
incendiarla o gettarla in acqua. Smaltirla secondo la normativa in vigore (DPR
915/82, successive disposizioni e disposizioni locali). L’impiego di una batteria
non adatta potrebbe determinare l’incendio o l’esplosione della batteria stessa.
La batería de repuesto es una batería de litio y puede provocar incendios,
explosiones o quemaduras graves. No la recargue, ni quite el conector polarizado,
ni la desmonte, ni caliente por encima de los 100°C (212°F), ni la incinere ni
exponga el contenido de sus celdas al agua. Deséchela tal como dispone la
normativa local.
10
Safety information
Safety notice 5
If the LCD breaks and the fluid from inside the LCD gets into your eyes or on your
hands, immediately wash the affected areas with water at least for 15 minutes.
Seek medical care if any symptoms caused by the fluid are present after washing.
Si le panneau d’affichage à cristaux liquides se brise et que vous recevez dans les
yeux ou sur les mains une partie du fluide, rincez-les abondamment pendant au
moins quinze minutes. Consultez un médecin si des symptômes persistent après le
lavage.
Die Leuchtstoffröhre im LCD-Bildschirm enthält Quecksilber. Bei der Entsorgung
die örtlichen Bestimmungen für Sondermüll beachten. Der LCD-Bildschirm
besteht aus Glas und kann zerbrechen, wenn er unsachgemäß behandelt wird
oder der Computer auf den Boden fällt. Wenn der Bildschirm beschädigt ist und
die darin befindliche Flüssigkeit in Kontakt mit Haut und Augen gerät, sollten
die betroffenen Stellen mindestens 15 Minuten mit Wasser abgespült und bei
Beschwerden anschließend ein Arzt aufgesucht werden.
Nel caso che caso l’LCD si dovesse rompere ed il liquido in esso contenuto
entrasse in contatto con gli occhi o le mani, lavare immediatamente le parti
interessate con acqua corrente per almeno 15 minuti; poi consultare un medico se i
sintomi dovessero permanere.
Si la LCD se rompe y el fluido de su interior entra en contacto con sus ojos o sus
manos, lave inmediatamente las áreas afectadas con agua durante 15 minutos
como mínimo. Obtenga atención medica si se presenta algún síntoma del fluido
despues de lavarse.
11
IdeaPad S205 Hardware Maintenance Manual
Safety notice 6
DANGER
To avoid shock, do not remove the plastic cover that protects the lower part of the
inverter card.
Afin d’éviter tout risque de choc électrique, ne retirez pas le cache en plastique
protégeant la partie inférieure de la carte d’alimentation.
Aus Sicherheitsgründen die Kunststoffabdeckung, die den unteren Teil der
Spannungswandlerplatine umgibt, nicht entfernen.
Per evitare scosse elettriche, non rimuovere la copertura in plastica che avvolge la
parte inferiore della scheda invertitore.
Para evitar descargas, no quite la cubierta de plástico que rodea la parte baja de la
tarjeta invertida.
Safety notice 7
DANGER
Though the main batteries have low voltage, a shorted or grounded battery can
produce enough current to burn personnel or combustible materials.
Bien que le voltage des batteries principales soit peu élevé, le court-circuit ou la
mise à la masse d’une batterie peut produire suffisamment de courant pour brûler
des matériaux combustibles ou causer des brûlures corporelles graves.
Obwohl Hauptbatterien eine niedrige Spannung haben, können sie doch bei
Kurzschluß oder Erdung genug Strom abgeben, um brennbare Materialien zu
entzünden oder Verletzungen bei Personen hervorzurufen.
Sebbene le batterie di alimentazione siano a basso voltaggio, una batteria in
corto circuito o a massa può fornire corrente sufficiente da bruciare materiali
combustibili o provocare ustioni ai tecnici di manutenzione.
Aunque las baterías principales tienen un voltaje bajo, una batería cortocircuitada
o con contacto a tierra puede producir la corriente suficiente como para quemar
material combustible o provocar quemaduras en el personal.
12
Safety information
Safety notice 8
DANGER
Before removing any FRU, turn off the computer, unplug all power cords from
electrical outlets, remove the battery pack, and then disconnect any interconnecting
cables.
Avant de retirer une unité remplaçable en clientèle, mettez le système hors tension,
débranchez tous les cordons d’alimentation des socles de prise de courant, retirez
la batterie et déconnectez tous les cordons d’interface.
Die Stromzufuhr muß abgeschaltet, alle Stromkabel aus der Steckdose gezogen,
der Akku entfernt und alle Verbindungskabel abgenommen sein, bevor eine FRU
entfernt wird.
Prima di rimuovere qualsiasi FRU, spegnere il sistema, scollegare dalle prese
elettriche tutti i cavi di alimentazione, rimuovere la batteria e poi scollegare i cavi
di interconnessione.
Antes de quitar una FRU, apague el sistema, desenchufe todos los cables de
las tomas de corriente eléctrica, quite la batería y, a continuación, desconecte
cualquier cable de conexión entre dispositivos.
13
IdeaPad S205 Hardware Maintenance Manual
Laser compliance statement
Some models of Lenovo IdeaPad computer are equipped from the factory with
an optical storage device such as a CD-ROM drive or a DVD-ROM drive. Such
devices are also sold separately as options. If one of these drives is installed,
it is certified in the U.S. to conform to the requirements of the Department of
Health and Human Services 21 Code of Federal Regulations (DHHS 21 CFR)
Subchapter J for Class 1 laser products. Elsewhere, the drive is certified to
conform to the requirements of the International Electrotechnical Commission
(IEC) 825 and CENELEC EN 60 825 for Class 1 laser products.
If a CD-ROM drive, a DVD-ROM drive, or another laser device is installed, note
the following:
CAUTION
Use of controls or adjustments or performance of procedures other than those
specified herein might result in hazardous radiation exposure.
O uso de controles, ajustes ou desempenho de procedimentos diferentes daqueles
aqui especificados pode resultar em perigosa exposição à radiação.
Pour éviter tout risque d’exposition au rayon laser, respectez les consignes de
réglage et d’utilisation des commandes, ainsi que les procédures décrites.
Werden Steuer- und Einstellelemente anders als hier festgesetzt verwendet, kann
gefährliche Laserstrahlung auftreten.
L’utilizzo di controlli, regolazioni o l’esecuzione di procedure diverse da quelle
specificate possono provocare l’esposizione a.
El uso de controles o ajustes o la ejecución de procedimientos distintos de los aquí
especificados puede provocar la exposición a radiaciones peligrosas.
Opening the CD-ROM drive, the DVD-ROM drive, or any other optical storage
device could result in exposure to hazardous laser radiation. There are no
serviceable parts inside those drives. Do not open.
14
Safety information
A CD-ROM drive, a DVD-ROM drive, or any other storage device installed may
contain an embedded Class 3A or Class 3B laser diode. Note the following:
DANGER
Emits visible and invisible laser radiation when open. Do not stare into the beam,
do not view directly with optical instruments, and avoid direct exposure to the
beam.
Radiação por raio laser ao abrir. Não olhe fixo no feixe de luz, não olhe
diretamente por meio de instrumentos óticos e evite exposição direta com o feixe
de luz.
Rayonnement laser si carter ouvert. Évitez de fixer le faisceau, de le regarder
directement avec des instruments optiques, ou de vous exposer au rayon.
Laserstrahlung bei geöffnetem Gerät. Nicht direkt oder über optische Instrumente
in den Laserstrahl sehen und den Strahlungsbereich meiden.
Kinyitáskor lézersugár ! Ne nézzen bele se szabad szemmel, se optikai
eszközökkel. Kerülje a sugárnyalábbal való érintkezést!
Aprendo l’unità vengono emesse radiazioni laser. Non fissare il fascio, non
guardarlo direttamente con strumenti ottici e evitare l’esposizione diretta al fascio.
Radiación láser al abrir. No mire fijamente ni examine con instrumental óptico el
haz de luz. Evite la exposición directa al haz.
15
IdeaPad S205 Hardware Maintenance Manual
Important service information
This chapter presents the following important service information:
•• “Strategy for replacing FRUs” on page 16
– “Strategy for replacing a hard disk drive” on page 17
– “Important notice for replacing a system board ” on page 17
•• “Important information about replacing RoHS compliant FRUs” on page 18
Important:
BIOS and device driver fixes are customer-installable. The BIOS and device
drivers are posted on the customer support site:
http://consumersupport.lenovo.com/.
Strategy for replacing FRUs
Before replacing parts:
Make sure that all software fixes, drivers, and BIOS downloads are installed
before replacing any FRUs listed in this manual.
After a system board is replaced, ensure that the latest BIOS is loaded to the
system board before completing the service action.
To download software fixes, drivers, and BIOS, follow the steps below:
1. Go to http://consumersupport.lenovo.com/.
2. Enter a serial number or select a product or use Lenovo smart downloading.
3. Select the BIOS/Driver/Applications and download.
4. Follow the directions on the screen and install the necessary software.
16
Important service information
Use the following strategy to prevent unnecessary expense for replacing and
servicing FRUs:
•• If you are instructed to replace an FRU, but the replacement does not solve
the problem, reinstall the original FRU before you continue.
•• Some computers have both a processor board and a system board. If you
are instructed to replace either of them, and replacing one of them does not
solve the problem, reinstall that board, and then replace the other one.
•• If an adapter or a device consists of more than one FRU, any of the FRUs
may be the cause of the error. Before replacing the adapter or device,
remove the FRUs one by one to see if the symptoms change. Replace only
the FRU that changed the symptoms.
Attention: The setup configuration on the computer you are servicing may
have been customized. Running Automatic Configuration may alter the
settings. Note the current configuration settings (using the View Configuration
option); then, when service has been completed, verify that those settings
remain in effect.
Strategy for replacing a hard disk drive
Always try to run a low-level format before replacing a hard disk drive. This
will cause all customer data on the hard disk to be lost. Make sure that the
customer has a current backup of the data before performing this action.
Attention: The drive startup sequence in the computer you are servicing may
have been changed. Be extremely careful during write operations such as
copying, saving, or formatting. If you select an incorrect drive, data or programs
can be overwritten.
Important notice for replacing a system board
Some components mounted on a system board are very sensitive. Improper
handling can cause damage to those components, and may cause a system
malfunction.
Attention: When handling a system board:
•• Do not drop the system board or apply any excessive force to it.
•• Avoid rough handling of any kind.
•• Avoid bending the system board and hard pushing to prevent cracking at
each BGA (Ball Grid Array) chipset.
17
IdeaPad S205 Hardware Maintenance Manual
Important information about replacing RoHS compliant FRUs
RoHS, The Restriction of Hazardous Substances in Electrical and
Electronic Equipment Directive (2002/95/EC) is a European Union legal
requirement affecting the global electronics industry. RoHS requirements
must be implemented on Lenovo products placed on the market after
June 2006. Products on the market before June 2006 are not required to
have RoHS compliant parts. If the original FRU parts are non-compliant,
replacement parts can also be non-compliant. In all cases if the original
FRU parts are RoHS compliant, the replacement part must also be RoHS
compliant.
Note: RoHS and non-RoHS FRU part numbers with the same fit and function
are identified with unique FRU part numbers.
Lenovo plans to transit to RoHS compliance well before the implementation
date and expects its suppliers to be ready to support Lenovo’s requirements
and schedule in the EU. Products sold in 2005 and 2006 will contain some
RoHS compliant FRUs. The following statement pertains to these products and
any product Lenovo produces containing RoHS compliant FRUs.
RoHS compliant FRUs have unique FRU part numbers. Before or after the
RoHS implementation date, failed RoHS compliant parts must always be
replaced with RoHS compliant ones, so only the FRUs identified as compliant
in the system HMM or direct substitutions for those FRUs may be used.
Products marketed before June 2006
Products marketed after June 2006
Current or
original part
Replacement FRU Current or
original part
Non-RoHS
Can be Non-RoHS
Non-RoHS
Can be RoHS
Non-RoHS
Can sub to RoHS
RoHS
Must be RoHS
Must be RoHS
Replacement FRU
Must be RoHS
Note: A direct substitution is a part with a different FRU part number that is
automatically shipped by the distribution center at the time of the order.
18
General checkout
General checkout
This chapter presents the following information:
•• “What to do first” on page 20
•• “Power system checkout” on page 21
Before you go to the checkout, make sure to read the following important notes:
Important notes:
• Only certified trained personnel can service the computer.
• Before replacing any FRU, read the entire page on removing and replacing
FRUs.
• When you replace FRUs, use new nylon-coated screws.
• Be extremely careful during such write operations as copying, saving, or
formatting. Drives in the computer that you are servicing sequence might
have been altered. If you select an incorrect drive, data or programs might be
overwritten.
• Replace an FRU only with another FRU of the correct model. When you
replace an FRU, make sure that the machine model and the FRU part number are
correct by referring to the FRU parts list.
• An FRU should not be replaced just because of a single, unreproducible
failure. Single failures can occur for a variety of reasons that have nothing to
do with a hardware defect, such as cosmic radiation, electrostatic discharge, or
software errors. Consider replacing an FRU only when a problem recurs. If you
suspect that an FRU is defective, clear the error logs and run the test again. If the
error does not recur, do not replace the FRU.
• Be careful not to replace a nondefective FRU.
19
IdeaPad S205 Hardware Maintenance Manual
What to do first
When you do return an FRU, you must include the following information in the
parts exchange form or parts return form that you attach to it:
1. Name and phone number of servicer
2. Date of service
3. Date on which the machine failed
4. Date of purchase
5. Procedure index and page number in which the failing FRU was detected
6. Failing FRU name and part number
7. Machine type, model number, and serial number
8. Customer’s name and address
Note for warranty: During the warranty period, the customer may be
responsible for repair costs if the computer damage was caused by misuse,
accident, modification, unsuitable physical or operating environment, or
improper maintenance by the customer.
The following is a list of some common items that are not covered under
warranty and some symptoms that might indicate that the system was
subjected to stress beyond normal use.
Before checking problems with the computer, determine whether the damage is
covered under the warranty by referring to the following list:
The following are not covered under warranty:
•• LCD panel cracked from the application of excessive force or from being
dropped
•• Scratched (cosmetic) parts
•• Distortion, deformation, or discoloration of the cosmetic parts
•• Plastic parts, latches, pins, or connectors that have been cracked or broken
by excessive force
•• Damage caused by liquid spilled into the system
•• Damage caused by the improper insertion of a PC Card or the installation of
an incompatible card
•• Improper disc insertion or use of an optical drive
•• Diskette drive damage caused by pressure on the diskette drive cover,
foreign material in the drive, or the insertion of a diskette with multiple labels
•• Damaged or bent diskette eject button
•• Fuses blown by attachment of a nonsupported device
•• Forgotten computer password (making the computer unusable)
•• Sticky keys caused by spilling a liquid onto the keyboard
•• Use of an incorrect AC adapter on laptop products
The following symptoms might indicate damage caused by nonwarranted
activities:
•• Missing parts might be a symptom of unauthorized service or modification.
•• If the spindle of a hard disk drive becomes noisy, it may have been subjected
to excessive force, or dropped.
20
General checkout
Power system checkout
To verify a symptom, follow the steps below:
1. Turn off the computer.
2. Remove the battery pack.
3. Connect the AC adapter.
4. Make sure that power is supplied when you turn on the computer.
5. Turn off the computer.
6. Disconnect the AC adapter and install the charged battery pack.
7. Make sure that the battery pack supplies power when you turn on the
computer.
If you suspect a power problem, see the appropriate one of the following power
supply checkouts:
•• “Checking the AC adapter ” on page 21
•• “Checking operational charging” on page 21
•• “Checking the battery pack ” on page 22
Checking the AC adapter
You are here because the computer fails only when the AC adapter is used.
•• If the power-on indicator does not turn on, check the power cord of the AC
adapter for correct continuity and installation.
•• If the computer does not charge during operation, go to “Checking
operational charging”.
To check the AC adapter, follow the steps below:
1. Unplug the AC adapter cable from the computer.
2. Measure the output voltage at the plug of the AC adapter cable. See the
following figure:
Pin
Voltage (V DC)
1
+20
2
0
2
1
Note: Output voltage for the AC adapter pin No. 2 may differ from the one you
are servicing.
3. If the voltage is not correct, replace the AC adapter.
4. If the voltage is acceptable, do the following:
•• Replace the system board.
•• If the problem continues, go to “Lenovo IdeaPad S205” on page 27.
Note: Noise from the AC adapter does not always indicate a defect.
Checking operational charging
To check whether the battery charges properly during operation, use a
discharged battery pack or a battery pack that has less than 50% of the total
power remaining when installed in the computer.
21
IdeaPad S205 Hardware Maintenance Manual
Perform operational charging. If the battery status indicator or icon does not
light on, remove the battery pack and let it return to room temperature. Reinstall
the battery pack. If the charge indicator or icon is still off, replace the battery
pack.
If the charge indicator still does not light on, replace the system board. Then
reinstall the battery pack. If it is still not charged, go to the next section.
Checking the battery pack
Battery charging does not start until the Power Meter shows that less than 95%
of the total power remains; under this condition the battery pack can charge to
100% of its capacity. This protects the battery pack from being overcharged or
from having a shortened life.
To check your battery, move your cursor to the Power Meter icon in the icon
tray of the Windows® taskbar and wait for a moment (but do not click it), and the
percentage of battery power remaining is displayed. To get detailed information
about the battery, double-click the Power Meter icon.
Note: If the battery pack becomes hot, it may not be able to be charged.
Remove it from the computer and leave it at room temperature for a while. After
it cools down, reinstall and recharge it.
To check the battery pack, follow the steps below:
1. Turn off the computer.
2. Remove the battery pack and measure the voltage between battery
terminals 1 (+) and 7 (-). See the following figure:
Terminal
1(+)
2(+)
5
3 4
6(-)
7(-)
Voltage (V DC)
1
+0 to +14
7
Ground (-)
3. If the voltage is less than +11.0 V DC, the battery pack has been
discharged.
Note: Recharging will be continued for at least 3 hours, even though the
indicator does not light on.
If the voltage is still less than +11.0 V DC after recharging, replace the
battery.
4. If the voltage is more than +11.0 V DC, measure the resistance between
battery terminals 5 and 7. The resistance must be 4 to 30 KΩ.
If the resistance is not correct, replace the battery pack. If the resistance is
correct, replace the system board.
22
Related service information
Related service information
This chapter presents the following information:
•• “Restoring the factory contents by using OneKey Recovery” on page 23
•• “Passwords” on page 24
•• “Power management” on page 25
Restoring the factory contents by using OneKey Recovery
Restore of factory default
The IdeaPad S205 computers come with pre-installed OneKey Rescue System.
In order to save application files and the initial backed up files of the system,
the hard disk in a Lenovo computer includes a hidden partition when it is
shipped. If you need to restore the system to the point of your first boot up, just
enter Lenovo OneKey Rescue System and run Restore to factory default. For
details of OneKey Rescue System, see the User Guide for OneKey Rescue System.
Note: This will delete all the new data on the system partition (C drive), which
is not recoverable. Make sure to back up your critical data before you perform this
action.
Using recovery discs
When you replace a hard disk drive in your computer, you are unable to use
the pre-installed Lenovo OneKey Recovery and OneKey Rescue. However, you
can use the recovery discs that store your backed up data to restore your new
hard drive to a previous backup status.
Note: You can create recovery discs by burning the backup image to a CD/DVD
as recovery discs. For details of Create recovery discs, see the User Guide for
OneKey Rescue System.
23
IdeaPad S205 Hardware Maintenance Manual
When you use the recovery discs to boot your computer, the system will enter
the user interface for system recovery automatically. Please follow the prompt
to insert the backup discs to complete the whole recovery process.
Note: The recovery process might take up to 2 hours.
Passwords
As many as two passwords may be needed for any Lenovo IdeaPad computer:
the power-on password (POP) and the supervisor password (SVP).
If any of these passwords has been set, a prompt for it appears on the screen
whenever the computer is turned on. The computer does not start until the
password is entered.
Exception: If only an SVP is installed, the password prompt does not appear
when the operating system is booted.
Power-on password
A power-on password (POP) protects the system from being powered on by
an unauthorized person. The password must be entered before an operating
system can be booted.
Supervisor password
A supervisor password (SVP) protects the system information stored in the
BIOS Setup Utility. The user must enter the SVP in order to get access to the
BIOS Setup Utility and change the system configuration.
Attention: If the SVP has been forgotten and cannot be made available to
the servicer, there is no service procedure to reset the password. The system
board must be replaced for a scheduled fee.
24
Related service information
Power management
Note: Power management modes are not supported for APM operating system.
To reduce power consumption, the computer has three power management
modes: screen blank, sleep (standby), and hibernation.
Screen blank mode
If the time set on the “Turn off monitor” timer in the operating system expires,
the LCD backlight turns off. You can also turn off the LCD backlight by pressing
Fn+F2.
To end screen blank mode and resume normal operation, press any key.
Sleep (standby) mode
When the computer enters sleep (standby) mode, the following events occur in
addition to what occurs in screen blank mode:
•• The LCD is powered off.
•• The hard disk drive is powered off.
•• The CPU stops.
To enter sleep (standby) mode, press Fn+F1.
In certain circumstances, the computer goes into sleep (standby) mode
automatically:
•• If a “suspend time” has been set on the timer, and the user does not do any
operation with the keyboard, the hard disk, the parallel connector, or the
diskette drive within that time.
•• If the battery indicator starts blinking, indicating that the battery power is low.
(Alternatively, if Hibernate when battery becomes low has been selected
in the “Power Management Properties” window, the computer goes into
hibernation mode.)
To cause the computer to return from sleep (standby) mode and resume the
operation, do one of the following:
•• Press the Fn key.
•• Open the lid.
•• Turn on the power switch.
Also, in the following event, the computer automatically returns from sleep
(standby) mode and resumes the operation:
•• The time set on the resume timer elapses.
Note: The computer does not accept any input immediately after it enters
sleep (standby) mode. Wait a few seconds before taking any action to reenter
operation mode.
25
IdeaPad S205 Hardware Maintenance Manual
Hibernation mode
In hibernation mode, the following occurs:
•• The system status, RAM, VRAM, and setup data are stored on the hard disk.
•• The system is powered off.
To cause the computer to enter hibernation mode, follow the steps below:
•• If you are using the ACPI operating system and have defined one of the
following actions as the event that causes the system to go into hibernation
mode, perform that action:
– Closing the lid.
– Pressing the power button.
Also, the computer goes into hibernation mode automatically in either of the
following conditions:
•• If a “hibernation time” has been set on the timer, and if the user does not do
any operation with the keyboard, the hard disk drive, the parallel connector,
or the diskette drive within that time.
•• If the timer conditions are satisfied in suspend mode.
When the power is turned on, the computer returns from hibernation mode and
resumes operation. The hibernation file in the boot record on the hard disk drive
is read, and system status is restored from the hard disk drive.
26
Lenovo IdeaPad S205
Lenovo IdeaPad S205
This chapter presents the following product-specific service references and
product-specific parts information:
•• “Specifications” on page 27
•• “Status indicators” on page 29
•• “Fn key combinations” on page 31
•• “FRU replacement notices” on page 32
•• “Removing and replacing an FRU” on page 33
•• “Locations” on page 60
•• “Parts list” on page 62
Specifications
The following table lists the specifications of the Lenovo IdeaPad S205 :
Table 1. Specifications
Feature
Description
Processor
•
•
•
•
•
•
•
Core Chipset
Bus architecture
Graphic memory
chip
Display
Standard
memory
CMOS RAM
Hard disk drive
Optical drive
AMD Brazos Platform (18w/9w)
E350, (1.6G, dual core)
E240, (1.5G, single core)
C50, (1.0G, dual core)
C30, (1.2G, single core)
Hudson M1 FCH
1066-MHz FSB
1066-MHz DDR2 SDRAM (PC2-8500)
PCI Bus
PCI Express Bus
DMI
• ATI Zacate APU
•
•
•
•
•
11.6" HD, LED backlight, Wedge type
1366 x 768 pixel, WXGA (200 nit, 255g)
DDR3-1066MHz (Support Dual Channel)
SODIMM socket x 2 (max 4GB per slot)
256 bytes
• 2.5” 9.5mm (7mm compatible) SATA II (SATA III capatible),
7200&5400rpm
• External (12.7mm - 2.5") USB RAMBO is Tray-in type
27
IdeaPad S205 Hardware Maintenance Manual
Table 1. Specifications (continued)
Feature
Description
I/O port
•
•
•
•
•
•
•
•
•
•
•
•
MODEM slot
Audio
Video
Ethernet (on the
system board)
PCI Express
Mini Card slot
Bluetooth
wireless
Keyboard
Touch pad
Integrated
camera
Battery
AC adapter
Pre-installed
operating
system
28
Stereo headphone jack
Microphone jack
VGA x 1
RJ45 x 1 (on planar)
USB2.0 x 3 (on planar)
HDMI x 1
6-in-1 card reader (SD/SD pro/MMC/MS/MS-pro/xD)
N/A
1/8" Stereo Headphone Output Jack
1/8" Input Jack Microphone
Built-in Stereo Speakers, 2 x 1.5W with 6 cc chamber
CRT port x 1 (on planar)
• 10/100M, AR8105EL Mega LAN
• Wireless LAN MiniCard (PCIe) slot x 1(half size)
• Wireless WAN MiniCard (PCIe) slot x 1(full size), select Models
• Built-in antenna with min-USB interface, select Models
• 6 Row, ISO Full Size Keyboard
• Two clicks and 1 LED indicator
• 1.3Million pixels/0.3Million pixels
• 3 cell, 2200mAh, 6 cell 2200mAh
• 20 V, 40 W/65 W
• Win 7 Starter, Home Basic/Premium (32bit/64bit)
Lenovo IdeaPad S205
Status indicators
The system status indicators below show the computer status:
5
1
2
3
4
Table 2. Status indicators
Indicator
1
Power on
Meaning
White:
System is enabled.
Blinking white:
System is in sleep mode.
Off: System is in hibernate mode or shut down.
29
IdeaPad S205 Hardware Maintenance Manual
Table 2. Status indicators (continued)
Indicator
30
2
Battery status
3
Wireless
status
4
Drive in use
5
Touchpad
Meaning
Blinking amber: (500ms off/1s on)
The remaining power of the battery is less than 5%
of its capacity.
Blinking amber: (100ms off/3.2s on)
The battery is being charged with the remaining
power between 5% and 20% of its capacity.
Amber:
The computer is operating on battery power with
the remaining power between 5% and 20% of its
capacity.
Blinking white:
The battery is being charged with the remaining
power between 20% and 80% of its capacity.
White:
The remaining power of the battery is more than
80% of its capacity, or the computer is operating on
battery power with the remaining power between
20% and 80% of its capacity.
White:
Any one of the wireless devices (WLAN/Bluetooth/
WWAN) is enabled.
Off:
All the wireless devices (WLAN/Bluetooth/WWAN)
are disabled.
White:
Data is being read from or written to the hard disk
drive. When this indicator is on, do not put the
computer into standby mode or turn off the computer.
Note: Do not move the system while the white drive-in-use
light is on. Sudden physical shock could cause drive errors.
White:
The touchpad is disabled. To enable or disable the
touchpad, press and hold the Fn key, and press the
F6 key.
Lenovo IdeaPad S205
Fn key combinations
The following table shows the function of each combination of Fn with a
function key.
Table 3. Fn key combinations
Key combination
Description
Fn + Esc:
Fn + F1:
Fn + F2:
Turn on/off the integrated camera.
Enter sleep mode.
Turn on/off the LCD screen.
Open the interface for the display device switch to select
notebook or external display.
Open the interface for integrated wireless devices settings
(enable/disable).
Enable/Disable the touchpad.
Start/Pause playback of Windows Media Player.
Stop playback of Windows Media Player.
Skip to the previous track.
Skip to the next track.
Activate the F12 function.
* You can press Fn+F11 during computer startup to open
the boot selection menu.
Activate the system request.
Activate the break function.
Enable/Disable the Scroll Lock.
Increase/Decrease display brightness.
Increase/Decrease volume level.
Fn + F3:
Fn + F5:
Fn + F6:
Fn + F7:
Fn + F8:
Fn + F9:
Fn + F10:
Fn + F11:
Fn + PrtSc:
Fn + Pause:
Fn + Delete:
Fn + / :
Fn + / :
31
IdeaPad S205 Hardware Maintenance Manual
FRU replacement notices
This section presents notices related to removing and replacing parts. Read
this section carefully before replacing any FRU.
Screw notices
Loose screws can cause a reliability problem. In the Lenovo IdeaPad computer,
this problem is addressed with special nylon-coated screws that have the
following characteristics:
•• They maintain tight connections.
•• They do not easily come loose, even with shock or vibration.
•• They are harder to tighten.
•• Each one should be used only once.
Do the following when you service this machine:
•• Keep the screw kit in your tool bag.
•• Always use new screws.
•• Use a torque screwdriver if you have one.
Tighten screws as follows:
•• Plastic to plastic
Turn an additional 90° after the screw head touches the surface of the
plastic part:
more than 90°
(Cross-section)
•• Logic card to plastic
Turn an additional 180° after the screw head touches the surface of the
logic card:
more than 180°
(Cross-section)
•• Torque driver
If you have a torque screwdriver , refer to the “Torque” column for each step.
•• Make sure that you use the correct screws. If you have a torque screwdriver,
tighten all screws firmly to the torque shown in the table. Never use a
screw that you removed. Use a new one. Make sure that all screws are
tightened firmly.
•• Ensure torque screwdrivers are calibrated correctly following country
specifications.
32
Lenovo IdeaPad S205
Removing and replacing an FRU
This section presents exploded figures with the instructions to indicate how to
remove and replace the FRU. Make sure to observe the following general rules:
1. Do not attempt to service any computer unless you have been trained and
certified. An untrained person runs the risk of damaging parts.
2. Before replacing any FRU, review “FRU replacement notices” on page 32.
3. Begin by removing any FRUs that have to be removed before the failing
FRU. Any of such FRUs are listed at the top of the page. Remove them in
the order in which they are listed.
4. Follow the correct sequence in the steps to remove the FRU, as given in the
figures by the numbers in square callouts.
5. When turning a screw to replace an FRU, turn it in the direction as given by
the arrow in the figure.
6. When removing the FRU, move it in the direction as given by the arrow in
the figure.
7. To put the new FRU in place, reverse the removal procedures and follow
any of the notes that pertain to replacement. For information about
connecting and arranging internal cables, see “Locations” on page 60.
8. When replacing an FRU, use the correct screw as shown in the procedures.
DANGER
Before removing any FRU, turn off the computer, unplug all power cords from
electrical outlets, remove the battery pack, and then disconnect any of the
interconnecting cables.
Attention: After replacing an FRU, do not turn on the computer until you have
made sure that all screws, springs, and other small parts are in place and none
are loose inside the computer. Verify this by shaking the computer gently and
listening for rattling sounds. Metallic parts or metal flakes can cause electrical
short circuits.
Attention: The system board is sensitive to, and can be damaged by,
electrostatic discharge. Before touching it, establish personal grounding by
touching a ground point with one hand or using an electrostatic discharge (ESD)
strap (P/N 6405959) to remove potential shock reasons.
33
IdeaPad S205 Hardware Maintenance Manual
1010 Battery pack
DANGER
Only use the battery specified in the parts list for your computer. Any other battery
could ignite or explode.
Figure 1. Removal steps of battery pack
Unlock the battery release lever 1. Holding the battery release lever in the
unlocked position 2, remove the battery pack in the direction shown by arrow
3.
2
3
2
1
1
When installing: Install the battery pack along the slide rails of the slot. Then
make sure that the battery release lever is in the locked position.
34
Lenovo IdeaPad S205
1020 Dummy card
For access, remove this FRU:
•• “1010 Battery pack” on page 34
Figure 2. Removal steps of dummy card
Remove the dummy card in the direction shown by arrows 1 2.
2
1
35
IdeaPad S205 Hardware Maintenance Manual
1030 SIM card
For access, remove this FRU:
•• “1010 Battery pack” on page 34
Figure 3. Removal steps of SIM card
Push the SIM card in until you hear a click, and then pull the SIM card out in
the direction shown by arrow 1.
1
36
Lenovo IdeaPad S205
1040 Keyboard
For access, remove this FRU:
•• “1010 Battery pack” on page 34
Figure 4. Removal steps of keyboard
Remove three screws 1.
1
1
1
Step
1
Screw (quantity)
Color
Torque
M2 × 2 mm, flat-head, nylok-coated (3)
Black
1.6 kgfcm
37
IdeaPad S205 Hardware Maintenance Manual
Figure 4. Removal steps of keyboard (continued)
Lift the keyboard a little, detach the connector in the direction shown by arrows
2 3, and then remove the keyboard 4.
4
2
3
When installing: Make sure that the FPC connector is attached firmly.
38
Lenovo IdeaPad S205
1050 Base cover
For access, remove these FRUs in order:
•• “1010 Battery pack” on page 34
•• “1040 Keyboard” on page 37
Figure 5. Removal steps of base cover
Remove four screws 1.
1
1
1
1
Step
1
Screw (quantity)
Color
Torque
M2 × 5 mm, flat-head, nylok-coated (4)
Black
1.6 kgfcm
39
IdeaPad S205 Hardware Maintenance Manual
Figure 5. Removal steps of base cover (continued)
Remove eight screws 2 on the bottom. Remove the base cover in the direction
shown by arrow 3.
2 2
2
2
2
2
2
3
Step
2
40
2
Screw (quantity)
Color
Torque
M2 × 5 mm, flat-head, nylok-coated (8)
Black
1.6 kgfcm
Lenovo IdeaPad S205
Note: Applying labels to the base cover
The new base cover FRU is shipped with a kit containing labels of several
kinds. When you replace the base cover, you need to apply the following
label:
The following labels need to be peeled off from the old base cover, and need
to be put on the new base cover.
a
PAINT Label
b
PRC/MTM Label
c
SYSTEM BARCODE Label
d
LAN ID Label
e
COA Label
f
Rating Label
g
Malaysia Sirim Label
h
Network Access License (for China)
i
SAR Label for US/CA
j
Indonesia D side Label
k
Indonesia WLAN&BT Label
l
ENERGY SAVING Label
For some models, you also need to apply one or two FCC labels. Check the
old base cover; if it has one or two FCC labels, find duplicates of them in the
label kit and apply them to the new base cover.
For the location of each label, refer to the following figure:
a
b
g
f
c
d
h
e
i
j
k
I
41
IdeaPad S205 Hardware Maintenance Manual
1060 PCI Express Mini Card for wireless LAN
For access, remove these FRUs in order:
•• “1010 Battery pack” on page 34
•• “1020 Dummy card” on page 35
•• “1040 Keyboard” on page 37
•• “1050 Base cover” on page 39
Figure 6. Removal steps of PCI Express Mini Card for wireless LAN
2
1
Disconnect two wireless LAN cables (black, white) in the direction shown by
arrow 1, and then remove one screw 2.
In step 1, unplug the jacks by using the removal tool antenna RF connector
(P/N: 08K7159), or pick up the connectors with your fingers and gently unplug
them in the direction shown by arrow.
Notes:wireless LAN card has 2 cables in step 1.
wireless LAN card in some models may have 3 cables in step 1.
Step
2
42
Screw (quantity)
Color
Torque
M2 × 3 mm, flat-head, nylok-coated (1)
Black
1.6 kgfcm
Lenovo IdeaPad S205
Figure 6. Removal steps of PCI Express Mini Card for wireless LAN (continued)
Remove two cards in the direction shown by arrow 3.
3
When installing:
•• In models with a wireless LAN card that has two antenna connectors, plug
the black cable (1st) (MAIN) into the jack labeled 1, and the white cable (2nd)
(AUX) into jack labeled 2 on the card.
•• In models with a wireless LAN card that has three antenna connectors, plug
the black cable (1st) (MAIN) into the jack labeled 1, the grey cable (3rd) into
jack labeled 3, and the white cable (2nd) (AUX) into jack labeled 2 on the
card.
43
IdeaPad S205 Hardware Maintenance Manual
1070 LCD unit
For access, remove these FRUs in order:
•• “1010 Battery pack” on page 34
•• “1020 Dummy card” on page 35
•• “1040 Keyboard” on page 37
•• “1050 Base cover” on page 39
•• “1060 PCI Express Mini Card for wireless LAN” on page 42
Figure 7. Removal steps of LCD unit
Remove the LCD connector 1 and release the LCD cable and antenna cables
from the cable guides 2.
1
2
2
2
2
Remove two screws 3.
3
3
Step
3
44
Screw (quantity)
Color
Torque
M2 × 5 mm, flat-head, nylok-coated (2)
Black
1.6 kgfcm
Lenovo IdeaPad S205
Figure 7. Removal steps of LCD unit (continued)
Swing the LCD hinges in the direction shown by arrows 4.
4
4
Remove the LCD unit in the direction shown by arrow 5.
5
45
IdeaPad S205 Hardware Maintenance Manual
1080 Hard disk drive (HDD)
For access, remove these FRUs in order:
•• “1010 Battery pack” on page 34
•• “1020 Dummy card” on page 35
•• “1040 Keyboard” on page 37
•• “1050 Base cover” on page 39
•• “1060 PCI Express Mini Card for wireless LAN” on page 42
•• “1070 LCD unit” on page 44
Attention:
• Do not drop the hard disk drive or apply any physical shock to it. The hard
disk drive is sensitive to physical shock. Improper handling can cause damages
and permanent loss of data.
• Before removing the drive, suggest the customer to backup all the information on
it if possible.
• Never remove the drive while the system is operating or is in suspend mode.
Figure 8. Removal steps of hard disk drive
Note: Remove two screws 1 and then remove the hard disk drive in the
direction shown by arrow 2.
1
1
Step
1
Screw (quantity)
Color
Torque
M2 × 5 mm, flat-head, nylok-coated (2)
Black
1.6 kgfcm
2
46
Lenovo IdeaPad S205
1090 DIMM
For access, remove these FRUs in order:
•• “1010 Battery pack” on page 34
•• “1020 Dummy card” on page 35
•• “1040 Keyboard” on page 37
•• “1050 Base cover” on page 39
Figure 9. Removal steps of DIMM
Release the two latches on both edges of the socket at the same time in the
direction shown by arrows 1, and then unplug the DIMM in the direction shown
by arrows 2.
2
1
1
1
1
2
When installing: Insert the notched end of the DIMM into the socket. Push the
DIMM firmly, and pivot it until it snaps into the place. Make sure that it is firmly
fixed in the slot and difficult to be moved.
47
IdeaPad S205 Hardware Maintenance Manual
1100 Fan assembly and heat sink assembly
For access, remove this FRU:
•• “1010 Battery pack” on page 34
•• “1020 Dummy card” on page 35
•• “1040 Keyboard” on page 37
•• “1050 Base cover” on page 39
•• “1060 PCI Express Mini Card for wireless LAN” on page 42
•• “1070 LCD unit” on page 44
Figure 10. Removal steps of fan assembly and heat sink assembly
Note: Loosen five screws 1 , but do not remove them. Detach the fan
connector in the direction shown by arrow 2.
1
1
1
1
1
2
When installing: Make sure that the fan connector is attached firmly to the
system board.
48
Lenovo IdeaPad S205
Figure 10. Removal steps of fan assembly and heat sink assembly (continued)
Lift the fan assembly and heat sink assembly in the direction shown by arrow 3.
Be careful not to damage the connector.
3
a
b
When installing: Before you attach the fan assembly to the computer, apply
thermal grease, at an amount of 0.2 grams, to the a b part shown in the figure
above. Either too much or too less grease application can cause a thermal
problem due to imperfect contact with a component.
49
IdeaPad S205 Hardware Maintenance Manual
1110 System board
Important notices for handling the system board:
When handling the system board, bear the following in mind.
• Be careful not to drop the system board on a bench top that has a hard surface,
such as metal, wood, or composite.
• Avoid rough handling of any kind.
• In the whole process, make sure not to drop or stack the system board.
• If you put a system board down, make sure to put it only on a padded surface such
as an ESD mat or conductive corrugated material.
For access, remove these FRUs in order:
•• “1010 Battery pack” on page 34
•• “1020 Dummy card” on page 35
•• “1040 Keyboard” on page 37
•• “1050 Base cover” on page 39
•• “1060 PCI Express Mini Card for wireless LAN” on page 42
•• “1070 LCD unit” on page 44
•• “1080 Hard disk drive (HDD)” on page 46
•• “1090 DIMM” on page 47
•• “1100 Fan assembly and heat sink assembly” on page 48
50
Lenovo IdeaPad S205
Figure 11. Removal steps of system board
Detach two connectors in the direction shown by arrows 1 2.
1
2
2
Remove three screws 3, detach the speakers connector in the direction shown
by arrow 4.
3
3
3
4
When installing: Make sure that all the connectors are attached firmly.
Step
3
Screw (quantity)
Color
Torque
M2 × 5 mm, flat-head, nylok-coated (3)
Black
1.6 kgfcm
51
IdeaPad S205 Hardware Maintenance Manual
Figure 11. Removal steps of system board (continued)
Remove the system board in the direction shown by arrow 5.
5
52
Lenovo IdeaPad S205
1120 Speakers
For access, remove these FRUs in order:
•• “1010 Battery pack” on page 34
•• “1020 Dummy card” on page 35
•• “1040 Keyboard” on page 37
•• “1050 Base cover” on page 39
•• “1060 PCI Express Mini Card for wireless LAN” on page 42
•• “1070 LCD unit” on page 44
•• “1080 Hard disk drive (HDD)” on page 46
•• “1090 DIMM” on page 47
•• “1100 Fan assembly and heat sink assembly” on page 48
•• “1110 System board” on page 50
Figure 12. Removal steps of speakers
Remove two screws 1, and release the cables from the cable guides 2.
1
1
2
2
Step
1
Screw (quantity)
Color
Torque
M2 × 3 mm, flat-head, nylok-coated (2)
Black
1.6 kgfcm
Remove the speakers in the direction shown by arrows 3.
3
3
53
IdeaPad S205 Hardware Maintenance Manual
1130 Bluetooth card
For access, remove these FRUs in order:
•• “1010 Battery pack” on page 34
•• “1020 Dummy card” on page 35
•• “1040 Keyboard” on page 37
•• “1050 Base cover” on page 39
•• “1060 PCI Express Mini Card for wireless LAN” on page 42
•• “1070 LCD unit” on page 44
•• “1080 Hard disk drive (HDD)” on page 46
•• “1090 DIMM” on page 47
•• “1100 Fan assembly and heat sink assembly” on page 48
•• “1110 System board” on page 50
Figure 13. Removal steps of bluetooth card
Remove the bluetooth card in the direction shown by arrow 1.
1
54
Lenovo IdeaPad S205
1140 LCD front bezel
For access, remove these FRUs in order:
•• “1010 Battery pack” on page 34
•• “1020 Dummy card” on page 35
•• “1040 Keyboard” on page 37
•• “1050 Base cover” on page 39
•• “1060 PCI Express Mini Card for wireless LAN” on page 42
•• “1070 LCD unit” on page 44
Figure 14. Removal steps of LCD front bezel
Remove two screws 1.
1
1
Step
1
Screw (quantity)
Color
Torque
M2 × 5 mm, flat-head, nylok-coated (2)
Black
1.6 kgfcm
Remove the LCD front bezel in the direction shown by arrows 2.
2
2
2
2
55
IdeaPad S205 Hardware Maintenance Manual
1150 LCD panel, LCD cable and hinges
For access, remove these FRUs in order:
•• “1010 Battery pack” on page 34
•• “1020 Dummy card” on page 35
•• “1040 Keyboard” on page 37
•• “1050 Base cover” on page 39
•• “1060 PCI Express Mini Card for wireless LAN” on page 42
•• “1070 LCD unit” on page 44
•• “1140 LCD front bezel” on page 55
Figure 15. Removal steps of LCD panel, LCD cable and hinges
Remove four screws 1 , detach the integrated camera connector in the
direction shown by arrow 2, and then remove the LCD panel in the direction
shown by arrow 3.
2
1
1
1
1
3
Step
1
56
Screw (quantity)
Color
Torque
M2 × 3 mm, flat-head, nylok-coated (4)
Black
1.6 kgfcm
Lenovo IdeaPad S205
Figure 15. Removal steps of LCD panel, LCD cable and hinges (continued)
Remove four screws 4 and then detach the hinges in the direction shown by
arrows 5.
5
4
4
4
5
4
Step
4
Screw (quantity)
Color
Torque
M2 × 2.5 mm, flat-head, nylok-coated (4)
White
1.6 kgfcm
When installing: Make sure that the connector is attached firmly.
Note: The LCD cables are attached to the LCD panel by a metal connector.
Peel off the adhesive tape and detach the metal connector in the direction
shown by arrow 6.
6
When installing: Make sure that the metal connector is attached firmly.
57
IdeaPad S205 Hardware Maintenance Manual
1160 Integrated camera
For access, remove these FRUs in order:
•• “1010 Battery pack” on page 34
•• “1020 Dummy card” on page 35
•• “1040 Keyboard” on page 37
•• “1050 Base cover” on page 39
•• “1060 PCI Express Mini Card for wireless LAN” on page 42
•• “1070 LCD unit” on page 44
•• “1140 LCD front bezel” on page 55
•• “1150 LCD panel, LCD cable and hinges” on page 56
Figure 16. Removal steps of integrated camera
Note: The integrated camera is stuck on the top center of the LCD cover.
Remove the integrated camera from the LCD cover in the direction shown by
arrow 1.
1
When installing: Stick the integrated camera to the top center of the LCD
cover and ajust the placement of it to make sure the connector is attached
firmly.
58
Lenovo IdeaPad S205
1170 Antenna assembly and LCD cover
For access, remove these FRUs in order:
•• “1010 Battery pack” on page 34
•• “1020 Dummy card” on page 35
•• “1040 Keyboard” on page 37
•• “1050 Base cover” on page 39
•• “1060 PCI Express Mini Card for wireless LAN” on page 42
•• “1070 LCD unit” on page 44
•• “1140 LCD front bezel” on page 55
•• “1150 LCD panel, LCD cable and hinges” on page 56
Figure 17. Removal steps of antenna assembly and LCD cover
Peel off the adhesive tapes securing the antenna boards, release the
cables from the cable guide, and then remove the antenna assembly in the
direction shown by arrows 1.
1
1
When installing: Route the antenna cables along the cable guides and secure
the antenna boards with adhesive tapes. As you route the cables, make sure
that they are not subjected to any tension. Tension could cause the cables to
be damaged by the cable guides, or a wire to be broken.
59
IdeaPad S205 Hardware Maintenance Manual
Locations
Front view
1 Integrated camera
2 Built-in microphone
3 Wireless module antennas (Select models only)
4 Power button
5 OneKey Rescue System button
6 System status indicators
Note: For the description of each indicator, see “Status indicators” on page 29.
7 Touchpad
3
2
1
3
4
5
6
6
7
60
Lenovo IdeaPad S205
Right-side view
1 Headphone jack
2 Microphone jack
3 Integrated wireless device switch
4 HDMI port
5 USB port
6 Kensington slot
7 RJ-45 port
1
2
3
7
6
5
4
Bottom and Left-side view
1 Memory card slot
2 Fan louvers
3 USB port
4 VGA port
5 AC power adapter jack
6 Battery latch - manual
7 Battery pack
8 SIM card slot (selected models only)
9 Battery latch - spring loaded
J Speakers
9
8
7
6
10
4
5
3
10
2
1
61
IdeaPad S205 Hardware Maintenance Manual
Parts list
This section presents the following service parts:
•• “Overall” on page 63
•• “LCD FRUs” on page 67
•• “Keyboard” on page 69
•• “Miscellaneous parts” on page 71
•• “AC adapters” on page 72
•• “Power cords” on page 73
Notes:
• Each FRU is available for all types or models, unless specific types or models
are specified.
62
Lenovo IdeaPad S205
Overall
1
2
3
4
5
c
6
7
8
10
9
11
12
a
13
14
63
IdeaPad S205 Hardware Maintenance Manual
Table 4. Parts list—Overall
No.
FRU
1
2
3
4
5
LCD unit (see “LCD FRUs” on page 67.)
Keyboard (see “Keyboard” on page 69.)
LS205 TOUCHPAD BUTTON BOARD W/CABLE
LS205 UPPER CASE W/SPEAKER&TOUCHPAD
BT2.1&BT3.0, Fcn BCM92070 BT2.1 EDR Flash U NB
Bluetooth card
BT2.1&BT3.0, USI BCM92070 BT2.1 EDR Flash U NB
Bluetooth card
LS205 SD DUMMY CARD
AMD E350 1.60G 1M B0 BGA processor
AMD E240 1.50G 512K B0 BGA processor
LS205 MB E350 1.6G W/THM/FAN/3G/HDMI
LS205 MB E350 1.6G W/THM/FAN/HDMI WO/3G
LS205 IO BOARD W/CABLE
DDRIII 1333 1GB, M471B2873FHS-CH9 (Rev F
/1Gb/46nm)
DDRIII 1333 1GB, RMT1910MD66E7F-1333
(V69A/2Gb/50nm)
DDRIII 1333 1GB, HMT112S6DFR8C-H9 N0 (Rev
Vega/1Gb/44nm)
DDRIII 1333 1GB, RMT3010EF48E7W-1333(Rev.
F/1Gb/60nm)
DDRIII 1333 1GB, SHA SY321NG08HBF DDR3 1333 1GB
DDRIII 1333 2GB, M471B5773CHS-CH9(Rev C /2Gb/46nm)
DDRIII 1333 2GB, NAN NT2GC64B88B0NS-CG DDR3
1333 2GB
DDRIII 1333 2GB, RMT1950MD58E8F1333(V69A/2Gb/50nm)
DDRIII 1333 2GB, HMT325S6BFR8C-H9 N0 (Rev
Vega/2Gb/44nm)
DDRIII 1333 2GB, RMT3020EF48E8W-1333(Rev
F/1Gb/60nm)
DDRIII 1333 2GB, SHA SY321NH08HAF DDR3 1333 2GB
DDRIII 1333 4GB, M471B5273CH0-CH9 (Rev C
/2Gb/46nm)
DDRIII 1333 4GB, HMT351S6BFR8C-H9 N0
(Vega/2Gb/44nm)
DDRIII 1333 4GB, MT16JSF51264HZ-1G4D1 (Rev
V69A/2Gb/50nm)
WLAN card, WiFi 1x1 BGN, Cbt RT3090 Wistron M PCIE
NB HMC
5
6
7
7
8
8
9
10
10
10
10
10
10
10
10
10
10
10
10
10
10
11
64
FRU no.
31049231
31049240
20002266
20002326
31049236
102001093
102001092
11013356
11013378
11013355
11011936
11012427
11012767
11012634
11012810
11012630
11012761
11012213
11012197
11012633
11012809
11011934
11012199
11012320
20002513
11
11
WLAN card, WiFi 1x1 BGN, Cbt RT3090 MOW M PCIE NB HMC 20002515
11
11
11
11011800
11012850
11012853
WLAN card, WiFi 1x1 BGN, Liteon AR9285 HB95 BGN
Wistron NB
Huawei EM770W WCDMA+GPS MiniPCIE WWAN
Huawei EM820W HSPA+850/900/1900/2100MHz
Ericsson F3307 R2 HSPA 900/2100MHz WWAN
20002353
Lenovo IdeaPad S205
Table 4. Parts list—Overall (continued)
No.
FRU
FRU no.
11
11
11
11
12
Ericsson F3307 R2 HSPA 850/1900MHz WWAN
Huawei EM660 EVDO+GPS WWAN card
Leadcoretech TD-SCDMA LC5740 Mini-Card
Huawei EM920 LTE MiniPCIE WWAN
HDD, 250G 5400rpm SATA, Hitachi HTS545025B9A300
250G 9NB
HDD, 250G 5400rpm SATA, WD2500BPVT-24ZEST0
5400RPM 250G
HDD, 250G 5400rpm SATA, Seagate ST9250315AS 250G
9NB
HDD, 250G 5400rpm SATA, HGST HTS543225A7A384
5400RPM7MM 250G
HDD, 250G 5400rpm SATA, Seagate ST250LT003 5400RPM
7MM 250G
HDD, 250G 5400rpm SATA, Toshiba MK2565GSX
5400RPM 250G
HDD, 320G 5400rpm SATA, Hitachi HTS545032B9A300 320G
9NB
HDD, 320G 5400rpm SATA, WD 4K sector 320GN
5400RPM250G
HDD, 320G 5400rpm SATA, HGST HTS543232A7A384
5400RPM7MM 320G
HDD, 320G 5400rpm SATA, Seagate ST320LT020 5400RPM
7MM 320G
HDD, 320G 5400rpm SATA, Toshiba MK3265GSX 5400RPM
320G
HDD, 320G 5400rpm SATA, Hitachi HTS545050B9A300 500G
9NB
HDD, 320G 5400rpm SATA, WD5000BPVT-24HXZT1
5400RPM 500G
HDD, 320G 5400rpm SATA, Seagate ST9500325AS 500G
9NB
HDD, 320G 5400rpm SATA, Toshiba MK5065GSX 5400RPM
500G
HDD, 320G 5400rpm SATA, WD WD7500BPVT-24HXZT1
5400RPM 750G
HDD, 320G 5400rpm SATA, Hitachi HTS725032A9A364
7200RPM320G
HDD, 320G 5400rpm SATA, Seagate ST9320423AS
7200RPM320G 9NB
HDD, 320G 5400rpm SATA, WD WD3200BEKT 7200RPM
320G
HDD, 320G 5400rpm SATA, HGST HTS723232A7A364
7200RPM7MM 320G
HDD, 320G 5400rpm SATA, Seagate ST320LT007 7200RPM
7MM 320G
HDD, 320G 5400rpm SATA, Hitachi HTS725050A9A364
7200RPM500G
11012852
11012299
11012849
11012302
16004060
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
16004852
16004186
16005023
16005210
16004641
16004059
16004853
16005024
16005211
16004642
16004058
16004846
16004189
16004643
16004848
16004530
16004533
16005212
16005027
16005030
16004531
65
IdeaPad S205 Hardware Maintenance Manual
Table 4. Parts list—Overall (continued)
No.
FRU
FRU no.
12
HDD, 320G 5400rpm SATA, Seagate ST9500420AS
7200RPM500G 9NB
HDD, 320G 5400rpm SATA, WD WD5000BEKT-24KA9T0
7200RPM 500G
Battery pack, 2.2Ah 3cell 24Wh, S205 Sanyo L09S3Z14
3S1P 24Wh Bty
Battery pack, 2.2Ah 3cell 24Wh, S205 SMP/S L09M3Z14
3S1P 24Wh Bty
Battery pack, 2.2Ah 3cell 24Wh, S205 Celx/L L09C3Z14
3S1P 24Wh Bty
Battery pack, 2.2Ah 6cell 48Wh, S205 Sanyo L09S6Y14
3S2P 48Wh Bty
Battery pack, 2.2Ah 6cell 48Wh, S205 SMP/S L09M6Y14
3S2P 48Wh Bty
Battery pack, 2.2Ah 6cell 48Wh, S205 Celx/L L09C6Y14
3S2P 48Wh Bty
LS205 LOWER CASE
AC adapter (see “AC adapters” on page 72.)
16004532
12
13
13
13
13
13
13
14
-
66
16004850
121001119
121001139
121001118
121001141
121001138
121001117
31049237
Lenovo IdeaPad S205
LCD FRUs
In Lenovo IdeaPad S205, there are following types of LCDs.
•• “11.6-in. WXGA TFT”
b
2
4
3
5
6
7
67
IdeaPad S205 Hardware Maintenance Manual
11.6-in. WXGA TFT
Table 5. Parts list—11.6-in. WXGA TFT
68
No.
FRU
FRU no.
1
2
3
3
3
3
4
5
5
6
7
LS205 LCD BEZEL W/CAMERA HOLE
LS205 HINGE CAP
11.6 Wedge, B116XW02 V0
11.6 Wedge, LP116WH1-TLN1
11.6 Wedge, LTN116AT03-L01
11.6 Wedge, N116B6-L02
LU16 LCD HINGE PACK AMD L/R
LS205 CAMERA 1.3M BISON W/MIC
LS205 CAMERA VGA BISON W/MIC
LS205 LVDS CABLE
LS205 LCD COVER W/ANTENNA FOR 3G
31049239
31049238
18004196
18004193
18004190
18004189
31044113
31049233
31049234
31049232
31049235
Lenovo IdeaPad S205
Keyboard
Table 6. Parts list—Keyboard
Language
Chicony
P/N
Bulgarian
International English
Swiss
Slovenian
Slovak
Icelandic
Belgian
Four Nordic countries
Hungarian
Hebrew
Greek
Dutch
Czech
Japanese
Brazilian
Arabic
German
French
Russian
Traditional Chinese
Korean
French&English
Latin
Portuguese
Thai
Turkish
Spanish
Italian
U.K. English
English
Czech-Slovakia
25010563
25010564
25010565
25010566
25010567
25010568
25010569
25010570
25010571
25010572
25010573
25010574
25010575
25010576
25010577
25010578
25010579
25010580
25010581
25010582
25010678
25010679
25010680
25010681
25010682
25010683
25010684
25010685
25010686
25010687
25011162
69
IdeaPad S205 Hardware Maintenance Manual
Table 6. Parts list—Keyboard (continued)
Language
ALPS
70
P/N
Portuguese
Bulgarian
International English
Swiss
Slovenian
Slovak
Icelandic
Belgian
Four Nordic countries
Hungarian
Hebrew
Greek
Dutch
Czech
Japanese
Brazilian
Arabic
German
French
Russian
Traditional Chinese
Korean
French&English
Latin
Thai
Turkish
Spanish
Italian
U.K. English
English
Czech-Slovakia
25010606
25010607
25010608
25010609
25010610
25010611
25010612
25010613
25010614
25010615
25010616
25010617
25010618
25010619
25010620
25010621
25010622
25010623
25010624
25010625
25010626
25010627
25010628
25010629
25010630
25010631
25010632
25010633
25010634
25010635
25011167
Lenovo IdeaPad S205
Miscellaneous parts
Table 7. Parts list—Miscellaneous parts
FRU
P/N
System miscellaneous parts:
• (a ) LU16 HDD BRACKET
31044111
• (b ) LS205 LCD SCREW RUBBER
31049241
Cable miscellaneous parts:
• (c ) LU16 BLUETOOTH CABLE
31044106
Note: Italicized letters in parentheses are references to the
exploded view in “Overall” on page 63 and “LCD FRUs” on page
67.
71
IdeaPad S205 Hardware Maintenance Manual
AC adapters
Table 8. Parts list—3-pin AC adapters
72
FRU
P/N
40Wh, Brazil PA-1400-12LB, adapter
40Wh, Delta ADP-40NH B, adapter
40Wh, Liteon PA-1400-12LC, adapter
40Wh, HIPRO LN-A0403A3C, adapter
65Wh, Delta ADP-65KH BD 20V/3.25A, adapter
65Wh, Liteon PA-1650-56LC, adapter
65Wh, Brazil PA-1650-52LB, adapter
65Wh, Chicony CPA-A065 20V3.25A, adapter(330PF)
36001715
36001648
36001653
36001672
36001929
36001651
36001714
36001943
Lenovo IdeaPad S205
Power cords
A Lenovo IdeaPad power cord for a specific country or region is usually
available only in that country or region:
Table 9. Parts list—3-pin power cords
Region
P/N
CCC
• SSD YD-118-1+IEC53RVV+SSD-3-2B-1 1m
CCC
• LINETEK PC323+RVV300/300+LS15 1m
Argentina
• LINETEK LS15+H03VV-F+LP39 1m
Danmark
• LINETEK LS15+H03VV-F+LP-38 1m
Switzerland
• LINETEK LS15+H03VV-F+LP-37 1m
Brazil
• LINETEK LS15 H03VV-F LP26A 1m
Israel
• LINETEK LS15+H03VV-F+LP-41 1m
UL
• LINETEK LP-30B + SPT-2 + LS15 1m
UK
• LINETEK LP-61L+ H03VV-F+ LS15 1m
Indian
• LINETEK PE-361+ H05VV-F+ LS15 1m
Italy
• LINETEK LS15+H03VV-F+PE-336 1m
Korea
• LINETEK LS15+H05VV-F+LP-E04A 1m
Australia
• LINETEK LS15+H03VV-F+LP-23A 1m
Taiwan
• LINETEK LS15+VCTF+LP-53 1m
Japan
• LINETEK LS15+VCTF+LP-54 1m
Africa
• LINETEK LS15+H03VV-F+PE-364 1m
CE
• LINETEK LP-34+H03VV-F + LS15 1m
CCC
• VOLEX GB10S3+RVV 300/500+VAC5S 1m
UL
• Volex US15S3+SPT-2 +VAC5S 1m
UK
• VOLEX MP5004+H03VV-F+VAC5S 1m
Indian
• VOLEX IA6A3+IS694+VAC5S 1m
145000602
145000600
145000599
145000598
145000597
145000596
145000595
145000594
145000593
145000592
145000591
145000590
145000589
145000588
145000587
145000586
145000585
145000538
145000537
145000605
145000536
73
IdeaPad S205 Hardware Maintenance Manual
Table 9. Parts list—3-pin power cords (continued)
74
Region
P/N
Switzerland
• VOLEX MP232+H03VV-F+VAC5S 1m
Italy
• VOLEX IT10S3+HO3VV-F+VAC5S 1m
Denmark
• VOLEX MP233D+H03VV-F+VAC5S 1m
Korea
• VOLEX M2511+KETI IEC+VAC5S 1m
Australia
• VOLEX AU10S3+H03VV-F+VAC5S 1m
Taiwan
• VOLEX TW15CS3+VCTF+VAC5S 1m
Japan
• VOLEX VAC5S+VCTF+M755 1m
Argentina
• VOLEX VA2073+H03VV-F+VAC5S 1m
Brazil
• VOLEX CH10S3+H03VV-F+VAC5S 1m
Israel
• VOLEX SI16S3+H03VV-F+VAC5S 1m
CE
• VOLEX M2511+HO3VV-F+VAC5S 1m
CCC
• Longwell LSG-31+RVV300/300+LS-18 1m
Argentina
• Longwell LP-24+H03VV-F+LS-18 1m
Danmark
• Longwell LP-40+H03VV-F+LS-18 1m
Switzerland
• Longwell LP-37+H03VV-F+LS-18 1m
Brazil
• Longwell LP-46+H03VV-F+LS-18 1m
Israel
• Longwell LP-41+H03VV-F+LS-18 1m
UL
• Longwell LP-30B+SPT-2 18AWG+LS-18 1m
UK
• Longwell LP-61L+H03VV-F+LS-18 1m
Indian
• Longwell LP-67+BIS+LS-18 1m
Italy
• Longwell LP-22+H03VV-F+LS-18 1m
Korea
• Longwell LP-486+KTLH03VV-F+LS-5 1m
145000524
145000535
145000534
145000533
145000532
145000531
145000530
145000528
145000527
145000526
145000525
145000568
145000567
145000566
145000565
145000564
145000563
145000562
145000561
145000560
145000559
145000558
Lenovo IdeaPad S205
Table 9. Parts list—3-pin power cords (continued)
Region
P/N
Australia
• Longwell LP-23A+LFC-3R+LS-18 1m
Taiwan
• Longwell LP-71+VCTF+LS-33 1m
Japan
• Longwell LP-54+VCTF+LS-18 1m
Africa
• Longwell LP-39+H03VV-F+LS-18 1m
CE
• Longwell LP-34A+H03VV-F+LS-18 1m
145000557
145000556
145000555
145000554
145000553
75
IdeaPad S205 Hardware Maintenance Manual
Notices
Lenovo may not offer the products, services, or features discussed in this
document in all countries. Consult your local Lenovo representative for
information on the products and services currently available in your area. Any
reference to a Lenovo product, program, or service is not intended to state or
imply that only that Lenovo product, program, or service may be used. Any
functionally equivalent product, program, or service that does not infringe
any Lenovo intellectual property right may be used instead. However, it is the
user’s responsibility to evaluate and verify the operation of any other product,
program, or service.
Lenovo may have patents or pending patent applications covering subject matter
described in this document. The furnishing of this document does not give you
any license to these patents.
L E N O V O G R O U P LT D . P R O V I D E S T H I S P U B L I C AT I O N “ A S I S ”
WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF NONINFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE. Some jurisdictions do not allow disclaimer of express or implied
warranties in certain transactions, therefore, this statement may not apply to you.
This information could include technical inaccuracies or typographical errors.
Changes are periodically made to the information herein; these changes
will be incorporated in new editions of the publication. Lenovo may make
improvements and/or changes in the product(s) and/or the program(s)
described in this publication at any time without notice.
The products described in this document are not intended for use in
implantation or other life support applications where malfunction may result in
injury or death to persons. The information contained in this document does not
affect or change Lenovo product specifications or warranties. Nothing in this
document shall operate as an express or implied license or indemnity under the
intellectual property rights of Lenovo or third parties. All information contained
in this document was obtained in specific environments and is presented as an
illustration. The result obtained in other operating environments may vary.
Lenovo may use or distribute any of the information you supply in any way it
believes appropriate without incurring any obligation to you.
Any references in this publication to non-Lenovo Web sites are provided for
convenience only and do not in any manner serve as an endorsement of those
Web sites. The materials at those Web sites are not part of the materials for
this Lenovo product, and use of those Web sites is at your own risk.
76
Notices
Any performance data contained herein was determined in a controlled
environment. Therefore, the result obtained in other operating environments
may vary significantly. Some measurements may have been made on
development-level systems and there is no guarantee that these measurements
will be the same on generally available systems. Furthermore, some
measurements may have been estimated through extrapolation. Actual results
may vary. Users of this document should verify the applicable data for their
specific environment.
Trademarks
The following terms are either registered trademarks or trademarks of Lenovo
in the United States and/or other countries:
Lenovo®
Lenovo logo®
IdeaPad®
VeriFace®
OneKey Rescue®(OneKey Recovery, OneKey Antivirus)
APS®
Power Express®
Energy Management and ReadyComm®
The following terms are trademarks of Microsoft Corporation in the United
States, other countries, or both:
Windows®
Windows Vista®
Windows® 7
The following are trademarks of Intel Corporation or its subsidiaries in the
United States, other countries, or both:
Intel®
Intel® Core™ 2 Duo
Other company, product, or service names may be the trademarks or service
marks of others.
77
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement