Omega 29023, 29025 Service Jack Operating Instructions & Parts Manual
Below you will find brief information for service jack 29023, service jack 29025. This document comes with the manual for the OMEGA service jack and provides instructions on how to assemble, operate, and maintain the unit. It also provides all safety information needed to operate the OMEGA service jack safely.
Advertisement
Advertisement
Operating Instructions & Parts Manual
MagicLift™ Service Jack, Low Profile
Model
29023
29025
Capacity
2 Ton
2 Ton
29023
29025
U.S. Patent No’s. 6,199,379 • 5,946,912
!
This is the safety alert symbol. It is used to alert you to potential personal injury hazards.
Obey all safety messages that follow this symbol to avoid possible injury or death.
!
ADVERTENCIA
• Leer, comprender, y seguir las instrucciónes antes de utilizar el aparato.
• El manual de instrucciónes y la información de seguridad deben estar comunicado en lengua del operador antes del uso.
• No seguir estas indicaciónes puede causar daños personales o materiales.
!
WARNING
To avoid crushing and related injuries:
• NEVER work on, under or around a load supported only by a hydraulic jack.
• ALWAYS use adequately rated jack stands.
SFA Companies
http://www.omegalift.com
Read this manual and follow all the Safety Rules and Operating Instructions before using this product.
Printed in China
29023-M2 rev 0710
SAFETY and GENERAL INFORMATION
Save these instructions. For your safety, read, understand, and follow the information provided with and on this jack before using. The owner and/or operator of this equipment shall have an understanding of this jack and safe operating procedures before attempting to use. The owner and/or operator shall be aware that the use and repair of this product may require special skills and knowledge. Instructions and safety information shall be conveyed in the operator’s native language before use of this jack is authorized. If any doubt exists as to the safe and proper use of this jack, remove from service immediately.
Inspect before each use. Do not use if broken, bent, cracked, or damaged parts (including labels) are noted. Any jack that appears damaged in any way, operates abnormally or is missing parts, shall be removed from service immediately and the manufacturer notified. If you suspect that the jack was subjected to a shock load (a load dropped suddenly, unexpectedly upon it), immediately discontinue use until jack has been checked by a factory authorized service center (contact distributor or manufacturer for list of Authorized Service Centers). It is recommended that an annual inspection be done by qualified personnel. Labels and owner’s manuals are available from manufacturer.
PRODUCT DESCRIPTION
The Omega MagicLift™ Low Profile Service Jack is designed to lift, but not support, one end of a vehicle. This jack must be used in conjunction with a pair of appropriately rated jack stands. Each MagicLift™ Service Jack has a unique feature, which provides fast, no load lifts to the jacking point, at which time it lifts in approximately 0.75~2" increments.
!
NEVER use a hydraulic jack as a stand-alone device. After lifting, immediately support the lifted vehicle with a pair of appropriately rated jack stands. NEVER place any portion of your body beneath the vehicle when lifting OR lowering!
SPECIFICATIONS
Model Capacity Jack Size (L x W x H) Min. Height Max. Height
29023 2 Ton 42-1/2" x 13-3/4" x 6-3/4" 20"
2-1/2"
29025 2 Ton 30" x 13-5/8" x 5-5/8" 19-5/8" front wheel saddle lift arm
Vent screw
(under cover plate,
on reservoir) handle handle sleeve
Figure 1 - Model 29023 Nomenclature
2 rear caster
PREPARATION
Assembly
Insert handle into the handle sleeve. Tighten the bolt on handle sleeve to prevent accidental removal of handle while in use.
Before Use
1. Verify that the product and the application are compatible, if in doubt call Omega Technical Service (888) 332-
6419.
2. Before using this product, read the operator's manual completely and familiarize yourself thoroughly with the product, its components and recognize the hazards associated with its use.
3. To familiarize yourself with basic operation of this jack, locate and turn the release valve (handle):
a. Clockwise until firm resistance is felt to further turning. This is the ‘ CLOSED’ release valve position used to
raise the load.
b. Counter-clockwise, but no more than 1/2 full turn from the closed position. This is the ‘ OPEN’ release valve
position used to lower the load.
4. Check to ensure that jack rolls freely. Raise and lower the unloaded saddle throughout the lifting range before putting into service to ensure the pump operates smoothly.
5. Replace worn or damaged parts and assemblies with Omega authorized replacement parts only. Lubricate as instructed in Maintenance Section.
Bleeding / Venting Trapped Air of Model 29025
With the release valve in the OPEN position (3b.) and with saddle fully lowered, locate and remove the oil filler plug. Pump 6 to 8 full strokes. This will help release any pressurized air which may be trapped within the reservoir.
Reinstall the oil filler plug.
Handle
Front Wheel
Saddle
Lifting Arm
Figure 2 - Model 29025 Nomenclature
3
Oil Filler Plug
(under cover plate, on reservoir)
Handle Sleeve
Rear Caster
!
WARNING
• Study, understand, and follow all printed materials provided with/on this product before use.
• Do not exceed rated capacity.
• Use only on hard, level surface.
•
This is a lifting device only!
• Immediately after lifting, support the load with
a pair of appropriately rated jack stands.
• Lift only on areas of the vehicle as specified by the vehicle manufacturer.
• Do not move or dolly the vehicle while on the jack.
• No alterations shall be made to this product.
• Failure to heed these markings may result in
personal injury and/or property damage.
!
WARNING
X
To avoid crushing and related injuries:
• Never work on, under or around a load supported only by hydraulic jack.
• Always use adequately rated jack stands.
• Chock each unlifted tire in both directions.
• Do not use this device to lift, level, lower, support nor move a house, mobile home, travel trailer, camper or any building structure.
• Be alert and sober when using this product. Do not operate under the influence of drugs or alcohol.
OPERATION
Lifting
!
Only attachments and/or adapters supplied by the manufacturer shall be used. Lift only on area of the vehicle as specified by the vehicle manufacturer.
1. Follow the vehicle manufacturer’s recommended guidelines for lifting. Engage the emergency brake and chock each unlifted wheel in both directions to prevent inadvertent vehicle movement.
2. Close the release valve by turning the handle clockwise until firm resistance is felt.
3. Refer to the vehicle manufacturer owner’s manual to locate approved lifting points on the vehicle. Center jack saddle under lift point.
4. Verify lift point, then pump handle to contact lift point. To lift, pump handle until load reaches desired height.
5. Transfer the load immediately to appropriately rated jack stands.
!
pair only! Do not exceed rated capacity.
Lowering
!
of speed at which the load lowers at all times!
Slowly open the release valve! The more
you turn the handle counter-clockwise, the faster the load will come down. Maintain control of the rate
1. Raise load high enough to clear the jack stands.
2. Remove jack stands carefully ( always used in pairs).
3. Slowly turn the handle counter-clockwise, but no more than 1/2 full turn. If the load fails to lower:
a. Use another jack to raise the vehicle high enough to reinstall jack stands.
b. Remove the malfunctioning jack and then the jack stands.
c. Use the functioning jack to lower the vehicle.
4. After removing jack from under the load, fully lower the saddle to reduce ram exposure to rust and contamination.
4
MAINTENANCE
!
premature failure of the jack and the potential for sudden and immediate loss of load.
Adding oil
It is difficult to confirm the correct oil level by simply looking into the oil reservoir after removing the vent screw.
*Correct oil level allows the saddle to reach its advertised maximum height and its advertised minimum height.
Lubrication
A periodic coating of light lubricating oil to pivot points, axles and hinges will help to prevent rust and assure that wheels, casters and pump assemblies move freely.
Cleaning
Periodically check the pump piston and ram for signs of rust or corrosion. Clean as needed and wipe with an oily cloth.
Note: Never use sandpaper or abrasive material on these surfaces!
•
completely.
•
Too little oil will not allow the saddle to raise
completely.
1. With saddle fully lowered set jack in its upright, level position. Remove vent screw (29023), oil plug
(29025).
2.
*
Fill until oil nearly covers the inner cylinder as seen from the oil filler hole. Reinstall the vent screw, oil plug .
Changing oil
For best performance and longest life, replace the complete fluid supply at least once per year.
1. With saddle fully lowered set jack in its upright, level position. Remove vent screw (29023), oil plug
(29025).
2. Lay the jack on its side and drain the fluid into a suitable container.
Note. Dispose of hydraulic fluid in accordance with local regulations.
3. *Fill until oil nearly covers the inner cylinder as seen from the oil filler hole. Reinstall the vent screw , oil filler plug.
TROUBLESHOOTING
Symptom
Jack will not lift load
Storage
When not in use, store the jack with saddle fully lowered.
Possible Causes
• Release valve not tightly closed
• Load is too heavy
Corrective Action
• Ensure release valve tightly closed
• Consider higher capacity jack
Jack will lift, but not maintain pressure
• Release valve not tightly closed
• Hydraulic unit malfunction
Jack will not lower after unloading • Reservoir overfilled
• Linkages binding
• Ensure release valve tightly closed
• Discontinue use, contact Omega
Technical Service
• Drain fluid to proper level
• Clean and lubricate moving parts
Poor lift performance
Will not lift to full extension
• Fluid level low
• Hydraulic unit malfunction
• Fluid level low
• Ensure proper fluid level
• Discontinue use, contact Omega
Technical Service
• Ensure proper fluid level
5
REPLACEMENT PARTS
(refer to page 7)
Not all components of the jack are replacement items, but are illustrated as a convenient reference of location and position in the assembly sequence. When ordering parts, give Model number, serial number and parts description.
Call or write for current pricing: SFA Companies, 10939 N. Pomona Ave. Kansas City, MO 64153, USA.
Tel: (888) 332-6419 Fax: (816) 891-6599 E-Mail: [email protected] Website: http://www.omegalift.com
Replacement Parts Illustration for model 29023
12
13
1
2
3
24 b c d i j
11 e f b g h q r l k
10 o p m n
25
8
9
20
21
22
18R
23
6 a
19
18L
5
16 17
15
14
4
Figure 3 - Replacement Parts Illustration for Model 29023
6
7
Replacement Parts List for model 29023
12
13
14
15
16
7
8
9
10
11
Item# Part#
1 G86301-0001
4
5
2
3
6
G86301-0017
G86308-0001
G86301-0004
G86301-0003
G86301-0008
G86301-0019
G86308-0003
G48900-0024
G86308-0004
G86301-0014
G86301-0012
G86308-0005
G86301-0023
G86301-0024
G88009-0016
23
24
25
**
17 G86301-0032
18R G59509-0016
18L
19
G59509-0015
G59305-0006
20
21
22
G73500-0011
G73500-0012
G59305-0005
G69400-0004
G69400-0003
G73500-0010
G86308-0000
-
29023-M1
29023-L0
**Repair Kit Contents: i g h f e c d
Item a b
Description
O-ring
O-ring
Back-up Washer
U-cup
Back-up Washer
O-ring
O-ring
Washer, Metal
Oil Seal
1
1
1
1
Qty
1
2
2
2
1
Description
Saddle Pad
Saddle
Hydraulic Unit
Front Wheel Assembly
Rear Caster Assembly
Handle Grip
Handle Assembly
Handle Sleeve
Bolt, M10x16
U-joint
Vent Screw
Return Spring, Lift Arm
Cover
Nut, M16
Spring Washer, D16
Bolt, M12
Nut, M12 4
Bolt, Handle Sleeve, RH side 1
Bolt, Handle Sleeve, LH side
Spring Washer, D20
1
2
Pin D12
Roller
Spring Washer, D10
1
1
1
Spring Pin
Cap, Pump Piston
Return Spring, Handle
Seal Kit (includes a thru r)
1
1
1
1
2
2
2
1
1
1
1
1
1
1
Qty.
1
2
2
1
1
1
Manual
Label
-
r
Item n o l m j k p q
Description
Back-up Washer
O-ring 13x2.4
O-ring 8x1.8
O-ring
Back-up Washer
O-ring 17x2.65
Back-up Washer
Back-up Washer
Oil Seal
1
1
1
1
1
1
1
Qty
1
1
(**) Replacement requires special skills, knowledge, and equipment. Only an authorized service center may perform the repair and/or replacement of these items.
7
REPLACEMENT PARTS
(refer to page 9)
Not all components of the jack are replacement items, but are illustrated as a convenient reference of location and position in the assembly sequence. When ordering parts, give Model number, serial number and parts description.
Call or write for current pricing: SFA Companies, 10939 N. Pomona Ave. Kansas City, MO 64153, USA.
Tel: (888) 332-6419 Fax: (816) 891-6599 E-Mail: [email protected] Website: http://www.omegalift.com
a b
2
1
13 c d
11
12 j i p o
3 k l e f b g h
8
22
23R
10 m n
23L
20
9
18
21
14
15
17
19
18
16
5
4
6
7
Figure 4 - Replacement Parts Illustration for Model 29025
8
Replacement Parts List for model 29025
14
15
16
9
10
11
12
13
6
7
4
5
8
Item# Part#
1
2
3
G72500-0009
G88002-0015
G72500-0010
G72500-0002
G72500-0003
G07000-0002
G72500-0007
G73500-0021
G48900-0024
G73500-0014
F36100-0001
G49300-0002
G72500-0014
G72500-0015
G72500-0016
G48900-0019
17
18
19
20
21
22
23L
G72500-0017
G48900-0020
G59305-0006
G73500-0011
G73500-0012
G59305-0005
G73500-0016
23R G73500-0010
** G72500-0000
-
29023-M1
29025-L0
Description
Saddle Pad
Saddle
Hydraulic Unit
Front Wheel Assembly
Rear Caster Assembly
Handle Grip
Handle Assembly
Handle Sleeve
Bolt, M10x16
U-joint
Oil Filler Plug
Return Spring, Lift Arm
Cover
Nut, M16
Spring Washer, D16
Bolt, M12
Nut, M12
Bolt, Handle Sleeve
Spring Washer, D20
Pin D12
Roller
Spring Washer, D10
Left Side Return Spring, Handle
Right Side Return Spring, Handle
Seal Kit (includes a thru p)
Manual
Label
2
2
1
1
2
1
1
1
1
1
2
2
1
Qty.
1
1
1
1
1
1
1
1
2
1
3
2
-
-
**Repair Kit Contents: f g d e h b c
Item a
Description
O-ring
O-ring
Back-up Washer
U-cup
Back-up Washer
O-ring
O-ring
Washer, Metal
1
2
1
1
2
Qty
1
2
1 j i l
Item k m n o p
Description
Oil Seal
Back-up Washer
O-ring 13x2.4
O-ring 8x1.8
O-ring 17x2.65
Back-up Washer
O-ring
Back-up Washer
1
1
1
1
1
Qty
2
2
1
(**) Replacement requires special skills, knowledge, and equipment. Only an authorized service center may perform the repair and/or replacement of these items.
9
ONE YEAR LIMITED WARRANTY
For a period of one (1) year from date of purchase, SFA Companies will repair or replace, at its option, without charge, any of its products which fails due to a defect in material or workmanship under normal usage. This limited warranty is a consumer's exclusive remedy.
Performance of any obligation under this warranty may be obtained by returning the warranted product, freight prepaid, to SFA Companies Warranty Service Department, 10939 N. Pomona Ave., Kansas City, MO 64153.
Except where such limitations and exclusions are specifically prohibited by applicable law,
(1) THE CONSUMER'S SOLE AND EXCLUSIVE REMEDY SHALL BE THE REPAIR OR REPLACEMENT OF
DEFECTIVE PRODUCTS AS DESCRIBED ABOVE.
(2) SFA Companies SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGE OR LOSS
WHATSOEVER.
(3) ANY IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, SHALL BE LIMITED TO ONE YEAR,
OTHERWISE THE REPAIR, REPLACEMENT OR REFUND AS PROVIDED UNDER THIS EXPRESS LIMITED
WARRANTY IS THE EXCLUSIVE REMEDY OF THE CONSUMER, AND IS PROVIDED IN LIEU OF ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED.
(4) ANY MODIFICATION, ALTERATION, ABUSE, UNAUTHORIZED SERVICE OR ORNAMENTAL DESIGN VOIDS
THIS WARRANTY AND IS NOT COVERED BY THIS WARRANTY.
Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state.
10
SFA Companies
10939 N. Pomona Ave. Kansas City, MO 64153
888-332-6419 [email protected]
Note Page
Contact:
SFA Companies
10939 N. Pomona Ave. Kansas City, MO 64153, U.S.A.
Tel:(888)332-6419 Fax:(816)891-6599
E-Mail:[email protected]
Omega Website: http://www.omegalift.com
Note Page
Contact:
SFA Companies
10939 N. Pomona Ave. Kansas City, MO 64153, U.S.A.
Tel:(888)332-6419 Fax:(816)891-6599
E-Mail:[email protected]
Omega Website: http://www.omegalift.com

Public link updated
The public link to your chat has been updated.
Advertisement
Key features
- Low Profile Design
- Fast, No Load Lifts
- Incremental Lifting
- Heavy Duty Construction
- Easy to Use
- Includes Parts Manual
- One Year Warranty
- Compatibility with Jack Stands