Panasonic H665 Microwave Oven User Manual

MA Motion Sensor (AMA1, AMB1, 2, 3)
MOTION SENSOR
(AREA REFLECTIVE TYPE)
FEATURES
New
1. Now even more miniature.
The new thin type cuts 35% from the
thickness of the previous short type.
Device installing is now easier than ever.
Existing short type
W10 × H20 × D19.5 mm
W.394 × H.787 × D.768 inch
⇓
Thin short type
W10 × H20 × D12.7 mm
W.394 × H.787 × D.500 inch
Thin short type
(Mounting direction: V type)
*“W” and “H” are detection value measurements.
Short type
(Mounting direction: H type)
Middle type
(Mounting direction: H type)
Long type
(Mounting direction: H type)
Long type
(Mounting direction: V type)
What is area reflective type?
The sensor emits a ray of light toward the
human body and detects the distance and
determine whether there is a person within
a given distance of the sensor. If the
sensor detects a person, it sets an output
non-contact switch to ON.
Reflected beam
Output
Non-contact
switch
MA MOTION
SENSOR Series
Light beam
Compliance with RoHS Directive
2. Certain detection unaffected by the
reflectance of the object
The sensor can provide stable
detection that is not affected by the
condition (color or material of the
clothing) or parts (skin, hair, etc.) of the
object being monitored. (Reflectance
18% to 90%). Excellent performance
even when the detection surface is dirty.
3. Only connecting DC power supply
for operating
Built-in oscillation circuit type obviates
the hitherto existing need for start signal
input.
4. Use in adjacent positions is
possible
These sensors can be located in
adjacent positions, because the timing of
the external trigger signals can be
adjusted so that the beam frequency of
each adjacent sensor will not interfere
with the other.
5. Battery drive possible
By applying longer interval for the trigger
signal, you can reduce the total power
consumption.
6. Can be used with a number of
different supply voltages.
1) The 5V DC type (4.5 to 6.5V DC)
2) The free-ranging power type (6.5 to
27V DC)
They support the DC power supplies of
electronic products and equipment in
general.
7. The open collector output system
makes for easy load drive.
These sensors provide a continuous
output during detection because the
output system makes it easy to drive the
load.
They achieve an output performance of
30V, Built-in oscillation circuit type:
100 mA, External triggering type: 10 mA
(Thin short type: 100 mA). Also, the thin
short type is available in a PNP open
collector type in addition to a NPN open
collector type.
APPLICATIONS
1. Water-based product market
• Automatic lighting of wash basin units
• Toilets
• Automatic water flow from faucets
2. Stores and financial instructions
• Automatic doors
• Automatic lighting
• Cash dispensing machines
• Automatic teller machines
• Visitor detecting sensors
3. Amusement market
• Automatic lighting for game display
4. Medical field
• Non-contact switch
5. Others
• Automatic ticket gates
• Seat-taking sensors
• Detection of passengers getting on and
off a bus
*The thin short type is only available for 5V DC.
All Rights Reserved © COPYRIGHT Panasonic Electric Works Co., Ltd.
MA Motion Sensor (AMA1, AMB1, 2, 3)
ORDERING INFORMATION
AM
MA Motion Sensor
A: Thin short type MA Motion sensor
B: MA Motion sensor
Detection distance type (shape)
1: Short type
2: Middle type
3: Long type
Triggering function
1: External triggering type
4: Built-in oscillation circuit type (Internal trigger)
Classification by output method & mounting direction
0: NPN open collector/H type
5: NPN open collector/V type
6: PNP open collector/V type
Operating voltage
2: Free-ranging power type (6.5 to 27V DC)
9: The DC 5V type (4.5 to 6.5V DC)
Rated detection distance
cm inch
Part No.
02
Detection
distance
Thin short type
Short type
Middle type
Long type
08
03
04
05
06
07
10
(Middle type
does not
need 08)
09
(Short type
does not
need 10)
20
11
12
13
14
15
16
17
18
19
(Long type
does not
need 20)
5
10
15
—
—
—
—
—
—
—
—
—
—
—
—
—
1.969
3.937
5.906
5
6
7
8
9
10
—
—
—
—
—
—
—
—
—
—
—
—
—
1.969 2.362 2.756 3.150 3.543 3.937
20
30
40
50
60
70
80
—
—
—
—
—
—
—
—
—
—
—
7.874 11.811 15.748 19.685 23.622 27.559 31.496 —
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
190
200
— 11.811
15.748 19.685 23.622 27.559 31.496 35.433 39.37 43.307 47.244 51.181 55.118 59.055 62.992 66.929 70.866 74.803 78.74
—
—
—
DETECTION DISTANCE TYPE (distance limited)
1. Thin short type (V type)
Mounting
direction
V type
Type
(shape)
Thin short
type
Operating
voltage
Part No.
Built-in oscillation circuit type
External triggering type
Output method
Rated detection
distance
NPN open
collector output
5 cm 1.969 inch
10 cm 3.937 inch
15 cm 5.906 inch
AMA145905
AMA1459
AMA145915
AMA115905
AMA1159
AMA115915
PNP open
collector output
5 cm 1.969 inch
10 cm 3.937 inch
15 cm 5.906 inch
AMA146905
AMA1469
AMA146915
AMA116905
AMA1169
AMA116915
4.5 to 6.5 V DC
Packing quantity
Inner
Outer
20 pcs.
200 pcs.
Note: If you plan to use multiple sensors side-by-side, or you wish to keep the current consumption small, inquire for details about external trigger type, which is suitable for
such applications.
2. Short type (H type)
Mounting
direction
Type (shape)
Rated operating
voltage
4.5 to 6.5 V DC
H type
Short type
6.5 to 27 V DC
Rated detection
distance
5 cm
6 cm
7 cm
8 cm
9 cm
10 cm
5 cm
6 cm
7 cm
8 cm
9 cm
10 cm
1.969 inch
2.362 inch
2.756 inch
3.150 inch
3.543 inch
3.937 inch
1.969 inch
2.362 inch
2.756 inch
3.150 inch
3.543 inch
3.937 inch
Part No.
Built-in oscillation circuit type
External triggering type
AMB140905
AMB110905
AMB140906
AMB110906
AMB140907
AMB110907
AMB140908
AMB110908
AMB140909
AMB110909
AMB1409
AMB1109
AMB140205
AMB110205
AMB140206
AMB110206
AMB140207
AMB110207
AMB140208
AMB110208
AMB140209
AMB110209
AMB1402
AMB1102
Packing quantity
Inner
Outer
20 pcs.
200 pcs.
Note: If you plan to use multiple sensors side-by-side, or you wish to keep the current consumption small, inquire for details about external trigger type, which is suitable for
such applications.
All Rights Reserved © COPYRIGHT Panasonic Electric Works Co., Ltd.
MA Motion Sensor (AMA1, AMB1, 2, 3)
3. Middle type (H type)
Mounting
direction
Type (shape)
Rated operating
voltage
4.5 to 6.5 V DC
H type
Middle type
6.5 to 27 V DC
Rated detection
distance
20 cm 7.874 inch
30 cm 11.811 inch
40 cm 15.748 inch
50 cm 19.685 inch
60 cm 23.622 inch
70 cm 27.559 inch
80 cm 31.496 inch
20 cm 7.874 inch
30 cm 11.811 inch
40 cm 15.748 inch
50 cm 19.685 inch
60 cm 23.622 inch
70 cm 27.559 inch
80 cm 31.496 inch
Part No.
Built-in oscillation circuit type
External triggering type
AMB240902
AMB210902
AMB240903
AMB210903
AMB240904
AMB210904
AMB240905
AMB210905
AMB240906
AMB210906
AMB240907
AMB210907
AMB2409
AMB2109
AMB240202
AMB210202
AMB240203
AMB210203
AMB240204
AMB210204
AMB240205
AMB210205
AMB240206
AMB210206
AMB240207
AMB210207
AMB2402
AMB2102
Packing quantity
Inner
Outer
20 pcs.
200 pcs.
Note: If you plan to use multiple sensors side-by-side, or you wish to keep the current consumption small, inquire for details about external trigger type, which is suitable for
such applications.
4. Long type (H type)
Mounting
direction
Type (shape)
Rated operating
voltage
4.5 to 6.5 V DC
H type
Long type
6.5 to 27 V DC
Rated detection
distance
30 cm 11.811 inch
40 cm 15.748 inch
50 cm 19.685 inch
60 cm 23.622 inch
70 cm 27.559 inch
80 cm 31.496 inch
90 cm 35.433 inch
100 cm 39.370 inch
110 cm 43.307 inch
120 cm 47.244 inch
130 cm 51.181 inch
140 cm 55.118 inch
150 cm 59.055 inch
160 cm 62.992 inch
170 cm 66.929 inch
180 cm 70.866 inch
190 cm 74.803 inch
200 cm 78.740 inch
30 cm 11.811 inch
40 cm 15.748 inch
50 cm 19.685 inch
60 cm 23.622 inch
70 cm 27.559 inch
80 cm 31.496 inch
90 cm 35.433 inch
100 cm 39.370 inch
110 cm 43.307 inch
120 cm 47.244 inch
130 cm 51.181 inch
140 cm 55.118 inch
150 cm 59.055 inch
160 cm 62.992 inch
170 cm 66.929 inch
180 cm 70.866 inch
190 cm 74.803 inch
200 cm 78.740 inch
Part No.
Built-in oscillation circuit type
External triggering type
AMB340903
AMB310903
AMB340904
AMB310904
AMB340905
AMB310905
AMB340906
AMB310906
AMB340907
AMB310907
AMB340908
AMB310908
AMB340909
AMB310909
AMB340910
AMB310910
AMB340911
AMB310911
AMB340912
AMB310912
AMB340913
AMB310913
AMB340914
AMB310914
AMB340915
AMB310915
AMB340916
AMB310916
AMB340917
AMB310917
AMB340918
AMB310918
AMB340919
AMB310919
AMB3409
AMB3109
AMB340203
AMB310203
AMB340204
AMB310204
AMB340205
AMB310205
AMB340206
AMB310206
AMB340207
AMB310207
AMB340208
AMB310208
AMB340209
AMB310209
AMB340210
AMB310210
AMB340211
AMB310211
AMB340212
AMB310212
AMB340213
AMB310213
AMB340214
AMB310214
AMB340215
AMB310215
AMB340216
AMB310216
AMB340217
AMB310217
AMB340218
AMB310218
AMB340219
AMB310219
AMB3402
AMB3102
Packing quantity
Inner
Outer
20 pcs.
200 pcs.
20 pcs.
200 pcs.
Note: If you plan to use multiple sensors side-by-side, or you wish to keep the current consumption small, inquire for details about external trigger type, which is suitable for
such applications.
All Rights Reserved © COPYRIGHT Panasonic Electric Works Co., Ltd.
MA Motion Sensor (AMA1, AMB1, 2, 3)
5. Long type (V type)
Mounting
direction
Type (shape)
Rated operating
voltage
4.5 to 6.5 V DC
V type
Long type
6.5 to 27 V DC
Rated detection
distance
30 cm 11.811 inch
40 cm 15.748 inch
50 cm 19.685 inch
60 cm 23.622 inch
70 cm 27.559 inch
80 cm 31.496 inch
90 cm 35.433 inch
100 cm 39.370 inch
110 cm 43.307 inch
120 cm 47.244 inch
130 cm 51.181 inch
140 cm 55.118 inch
150 cm 59.055 inch
160 cm 62.992 inch
170 cm 66.929 inch
180 cm 70.866 inch
190 cm 74.803 inch
200 cm 78.740 inch
30 cm 11.811 inch
40 cm 15.748 inch
50 cm 19.685 inch
60 cm 23.622 inch
70 cm 27.559 inch
80 cm 31.496 inch
90 cm 35.433 inch
100 cm 39.370 inch
110 cm 43.307 inch
120 cm 47.244 inch
130 cm 51.181 inch
140 cm 55.118 inch
150 cm 59.055 inch
160 cm 62.992 inch
170 cm 66.929 inch
180 cm 70.866 inch
190 cm 74.803 inch
200 cm 78.740 inch
Part No.
Built-in oscillation circuit type
External triggering type
AMB345903
AMB315903
AMB345904
AMB315904
AMB345905
AMB315905
AMB345906
AMB315906
AMB345907
AMB315907
AMB345908
AMB315908
AMB345909
AMB315909
AMB345910
AMB315910
AMB345911
AMB315911
AMB345912
AMB315912
AMB345913
AMB315913
AMB345914
AMB315914
AMB345915
AMB315915
AMB345916
AMB315916
AMB345917
AMB315917
AMB345918
AMB315918
AMB345919
AMB315919
AMB3459
AMB3159
AMB345203
AMB315203
AMB345204
AMB315204
AMB345205
AMB315205
AMB345206
AMB315206
AMB345207
AMB315207
AMB345208
AMB315208
AMB345209
AMB315209
AMB345210
AMB315210
AMB345211
AMB315211
AMB345212
AMB315212
AMB345213
AMB315213
AMB345214
AMB315214
AMB345215
AMB315215
AMB345216
AMB315216
AMB345217
AMB315217
AMB345218
AMB315218
AMB345219
AMB315219
AMB3452
AMB3152
Packing quantity
Inner
Outer
20 pcs.
200 pcs.
20 pcs.
200 pcs.
Note: If you plan to use multiple sensors side-by-side, or you wish to keep the current consumption small, inquire for details about external trigger type, which is suitable for
such applications.
PERFORMANCE
1. Detection performance (Measuring conditions: ambient temp.: 25°C 77°F; operating voltage: 5 V DC)
1) Thin short type
Items
Minimum
Rated detection distance
Typical
Maximum
Measuring tolerance
Usable
ambient
brightness
(Resistance
to ambient
light)*2
Typical
Brightness
of sensor
Maximum
surface
Brightness
of reflection Maximum
surface
5 cm
1.969 inch
45 mm
1.772 inch
50 mm
1.969 inch
55 mm
2.165 inch
10%
Thin short type
10 cm
3.937 inch
15 cm
3.937 inch
90 mm
3.543 inch
100 mm
3.937 inch
110 mm
4.331 inch
135 mm
5.315 inch
150 mm
5.906 inch
165 mm
6.496 inch
with a standard
reflection
board*1
25%
35%
Reflection rate:
90 to 18%
30,000 lx
30,000 lx
Measured
conditions
See the drawing
(Fig. 1) on the
next page.
Notes: *1. Ambient brightness: 500 lx
*2. Install so that light from direct light sources does not enter the sensor (within 30° of the sensor light beam).
Indicates brightness detectible enough for sensor operation. (Measuring conditions: ambient temp.: 25°C 77°F; operating voltage: 5 V DC type 5V, Free-ranging
power type 24V DC)
All Rights Reserved © COPYRIGHT Panasonic Electric Works Co., Ltd.
MA Motion Sensor (AMA1, AMB1, 2, 3)
2) Short type
Items
Minimum
Rated detection distance
Typical
Maximum
Measuring tolerance
Usable
ambient
brightness
(Resistance
to ambient
light)*2
5 cm
1.969 inch
45 mm
1.772 inch
50 mm
1.969 inch
55 mm
2.165 inch
Typical
6 cm
2.362 inch
Short type*1
7 cm
8 cm
2.756 inch
3.150 inch
9 cm
3.543 inch
10 cm
3.937 inch
54 mm
2.126 inch
60 mm
3.362 inch
66 mm
2.598 inch
63 mm
2.480 inch
70 mm
2.756 inch
77 mm
3.031 inch
81 mm
3.189 inch
90 mm
3.543 inch
99 mm
3.898 inch
90 mm
3.543 inch
100 mm
3.937 inch
110 mm
4.331 inch
with a standard
reflection board
25%
Reflection rate:
90 to 18%
10%
72 mm
2.835 inch
80 mm
3.150 inch
88 mm
3.465 inch
15%
Brightness
of sensor
Maximum
surface
Brightness
of reflection Maximum
surface
20%
30,000 lx
Measured
conditions
See the drawing
(Fig. 1) on the
next page.
30,000 lx
Notes: *1. After receipt of order, average rated detection distance to 15 cm 5.906 inch is possible. Please inquire.
*2. Install so that light from direct light sources does not enter the sensor (within 30° of the sensor light beam).
3) Middle type (Measuring conditions: ambient temp.: 25°C 77°F; operating voltage: 5 V DC type 5V, Free-ranging power type 24V DC)
Items
Minimum
Rated detection distance
Typical
Maximum
Measuring tolerance
Usable
ambient
brightness
(Resistance
to ambient
light)*2
20 cm
7.874 inch
190 mm
7.480 inch
200 mm
7.874 inch
210 mm
8.268 inch
Typical
30 cm
11.811 inch
40 cm
15.748 inch
Middle type*1
50 cm
19.685 inch
285 mm
11.220 inch
300 mm
11.811 inch
315 mm
12.402 inch
380 mm
14.961 inch
400 mm
15.748 inch
420 mm
16.535 inch
475 mm
18.701 inch
500 mm
19.685 inch
525 mm
20.669 inch
3%
60 cm
23.622 inch
70 cm
27.559 inch
80 cm
31.496 inch
570 mm
22.441 inch
600 mm
23.622 inch
630 mm
24.803 inch
665 mm
26.181 inch
700 mm
27.559 inch
735 mm
28.937 inch
760 mm
29.921 inch
800 mm
31.496 inch
840 mm
33.071 inch
5%
Brightness
of sensor
Maximum
surface
Brightness
of reflection Maximum
surface
10%
30,000 lx
Measured
conditions
with a standard
reflection board
Reflection rate:
90 to 18%
See the drawing
(Fig. 1) on the
next page.
30,000 lx
Notes: *1. After receipt of order, average rated detection distance to 110 cm 43.307 inch is possible. Please inquire.
*2. Install so that light from direct light sources does not enter the sensor (within 30° of the sensor light beam).
4) Long type (Measuring conditions: ambient temp.: 25°C 77°F; operating voltage: 5 V DC type 5V, Free-ranging power type 24V DC)
Items
Rated detection distance
Measuring tolerance
Usable
ambient
brightness
(Resistance
to ambient
light)*
Brightness
of sensor
surface
40 cm
15.748 inch
380 mm
14.961 inch
400 mm
15.748 inch
420 mm
16.535 inch
Typical
50 cm
19.685 inch
475 mm
18.701 inch
500 mm
19.685 inch
525 mm
20.669 inch
60 cm
23.622 inch
570 mm
22.441 inch
600 mm
23.622 inch
630 mm
24.803 inch
Long type
70 cm
27.559 inch
665 mm
26.181 inch
700 mm
27.559 inch
735 mm
28.937 inch
Brightness
of reflection Maximum
surface
30,000 lx
Measuring tolerance
120 cm
47.244 inch
1140 mm
Minimum
44.882 inch
1200 mm
Typical
47.244 inch
Maximum 1260 mm
49.606 inch
Typical
Brightness
of sensor
Maximum
surface
Brightness
of reflection Maximum
surface
90 cm
100 cm
35.433 inch 39.37 inch
950 mm
855 mm
33.661 inch 37.402 inch
1000 mm
900 mm
34.433 inch 39.37 inch
1050 mm
945 mm
37.205 inch 41.339 inch
5%
30,000 lx
Rated detection distance
80 cm
31.496 inch
760 mm
29.921 inch
800 mm
31.496 inch
840 mm
33.071 inch
3%
Maximum
Items
Usable
ambient
brightness
(Resistance
to ambient
light)*
30 cm
11.811 inch
285 mm
Minimum
11.220 inch
300 mm
Typical
11.811 inch
315 mm
Maximum
12.402 inch
5%
130 cm
51.181 inch
1235 mm
48.622 inch
1300 mm
51.181 inch
1365 mm
53.740 inch
140 cm
55.118 inch
1330 mm
52.362 inch
1400 mm
55.118 inch
1470 mm
57.874 inch
150 cm
49.055 inch
1425 mm
56.102 inch
1500 mm
59.055 inch
1575 mm
62.008 inch
Long type
160 cm
62.992 inch
1520 mm
59.842 inch
1600 mm
62.992 inch
1680 mm
66.142 inch
Measured
110 cm
conditions
43.307 inch
1045 mm
41.142 inch
1100 mm with a standard
43.307 inch reflection board
1155 mm
45.472 inch
Reflection rate:
90 to 18%
See the drawing
(Fig. 1) on the
next page.
170 cm
66.929 inch
1615 mm
63.583 inch
1700 mm
66.929 inch
1785 mm
70.275 inch
10%
180 cm
70.866 inch
1710 mm
67.323 inch
1800 mm
70.866 inch
1890 mm
74.409 inch
Measured
190 cm
200 cm
conditions
74.803 inch 78.74 inch
1900 mm
1805 mm
71.063 inch 74.803 inch
2000 mm with a standard
1900 mm
74.803 inch 78.74 inch reflection board
2100 mm
1995 mm
78.543 inch 82.677 inch
15%
30,000 lx
30,000 lx
Note: * Install so that light from direct light sources does not enter the sensor (within 30° of the sensor light beam).
All Rights Reserved © COPYRIGHT Panasonic Electric Works Co., Ltd.
Reflection rate:
90 to 18%
See the drawing
(Fig. 1) on the
next page.
MA Motion Sensor (AMA1, AMB1, 2, 3)
• For thin short type:
Standard reflection board: 100 mm 3.937 inch square area,
90% reflection rate.
• For short type:
Standard reflection board: 100 mm 3.937 inch square area,
90% reflection rate.
• For middle type:
Standard reflection board: 200 mm 7.874 inch square area,
90% reflection rate.
• For long type:
Standard reflection board: 500 mm 19.685 inch square area,
90% reflection rate.
<Fig. 1>
[Brightness of sensor surface]
Notes: 1. Detecting an object within the maximum preset detection distance.
2. Distance deviation = a – b × 100 (%)
a
a: detection distance of detection target with reflectance of 90%.
b: detection distance of standard detection target with reflectance of 18%.
[Brightness of reflection surface]
(θ1, θ1′) > 15°
Sensor
30°
θ1
θ1′
Sensor
❇Area for prohibit
direct light
30°*(θ2, θ2′)* 45°
θ2
θ2′
Light meter
Light meter
Reflection
board
Note: Light from direct light sources (sunlight, strobe light, inverter illumination,
reflected light from glass or mirrors etc.) that enters the sensor from within
the prohibited range can cause the sensor to operate erroneously.
Rated detection distance
2. Absolute maximum rating (Measuring condition: ambient temp.: 25°C 77°F)
Type
Items
Power supply voltage
Output dielectric strength
Output flow current
Usable ambient temperature
Storage temperature
Built-in oscillation circuit type
5 V DC type
Free-ranging power type
–0.3 to 8 V DC
–0.3 to 30 V DC
30 V
100 mA
–25 to +75°C +5 to +131°F (No freezing)
–30 to +85°C –4 to +176°F
External triggering type
5 V DC type
Free-ranging power type
–0.3 to 8 V DC
–0.3 to 30 V DC
30 V
10 mA*
–25 to +75°C +5 to +131°F (No freezing)
–30 to +85°C –4 to +176°F
Note: * Thin short type is only: 100 mA
3. Electrical characteristics
(Measuring conditions: ambient temp.: 25°C 77°F; operating voltage: 5 V DC type =5V DC, free-ranging power type =24V DC)
1) Built-in oscillation circuit type
Items
Rated operating voltage
No detection
Average current
consumption
(Iout = 0 mA)
Detection
Measuring cycle
Output
characteristics
Remain voltage
Leakage current
T
Thin short type*
NPN
PNP
Short type
Middle type
Long type
output
output
type
type
5V DC type: 4.5V/Free-ranging power type: 6.5V
—
5V DC type: 6.5V/Free-ranging power type: 27V
—
4.5mA
5V DC type: 4.5mA/Free-ranging power type: 5.6mA
6.2mA
5V DC type: 6.2mA/Free-ranging power type: 7.8mA
—
7.0mA
11.0mA
5V DC type: 7.0mA/Free-ranging power type: 9.1mA
11.2mA 15.2mA 5V DC type: 11.2mA/Free-ranging power type: 14.2mA
8ms/cycle
Vr
Il
1 V DC 1.2 V DC
5µA
Symbol
Minimum
Typical
Maximum
Minimum
Typical
Maximum
Minimum
Typical
Maximum
Minimum
Maximum
Maximum
Vdd
It
It
1 V DC
3µA
Note: * The thin short type is only available for 5V DC.
All Rights Reserved © COPYRIGHT Panasonic Electric Works Co., Ltd.
Measured conditions
It = 100 mA
V = 30V
MA Motion Sensor (AMA1, AMB1, 2, 3)
2) External triggering type (trigger conditions: trigger pulse width = 20µs and trigger synchronization = 5ms)
Items
Symbol
Minimum
Typical
Maximum
Rated operating voltage
Minimum
Typical
Maximum
Minimum
Typical
Maximum
Output OFF
Without
trigger input
Output ON
Average current
consumption
Output OFF
With trigger
input
Output ON
Measuring cycle (Trigger interval)
Pulse width
External trigger
Level
Response performance:
time from trigger pulse fall to detection output
Output
characteristics
Vdd
Remain voltage
Leakage current
Thin short type
Note 1
Short type
Middle type
Long type
NPN
PNP
output
output
type
type
5V DC type: 4.5V/Free-ranging type: 6.5V
—
5V DC type: 6.5V/Free-ranging type: 27V
Ib
Id
Minimum
Typical
Maximum
Minimum
Typical
Maximum
Minimum
Minimum
Maximum
Maximum
Minimum
VTL
VTH
Maximum
Tr
Maximum
Maximum
Vr
Il
Ia
Ic
—
5V DC type: 0.1mA/Free-ranging type: 1.0mA
5V DC type: 0.3mA/Free-ranging type: 1.8mA
—
5V DC type: 0.5mA/Free-ranging type: 1.4mA
5V DC type: 3.4mA/Free-ranging type: 4.5mA
0.1m
0.3m
2.6mA
6.6mA
6.7mA
9.6mA
2.2mA
6.2mA
4.2mA
8.2mA
Measured conditions
6.2mA
12.5mA
Tt
Tw
—
5V DC type: 2.2mA/Free-ranging type: 3.1mA
5V DC type: 6.2mA/Free-ranging type: 7.2mA
—
5V DC type: 2.4mA/Free-ranging type: 3.3mA
5V DC type: 8.2mA/Free-ranging type: 9.3mA
5ms/cycle
20µs
1/2Tt
0.8V
3V
Note 2: *b
Note 2: *d
Note 2: *a
Note 2: *c
Half off the distance period
Note 3
5ms
1 V DC 1.2 V DC
5µA
Notes: 1. The thin short type is only available for 5V DC.
2. The ratio between the 4 operating modes (*a to *d) depends on the
external trigger period and detector time, and the current consumption
corresponds with this varying ratio.
1V
3µA
I = 10 mA
V = 30 mA
4. The output transistor is open collector.
The output transistor is turned ON by the sensor detection status and
turned OFF by its non-detection status.
Sensor
Trigger input
*a
*b
*c
*d
Detection status:
output transistor ON
Output
Operation
Internal sensor
operation
Output
transistor
Non-detection status:
output transistor OFF
Stand by
OFF 2 ms
(approx.)
2 ms
(approx.)
2 ms
(approx.)
2 ms
(approx.)
GND
(With trigger input) (Without trigger input) (With trigger input) (Without trigger input)
(NPN output types of the AMA series and all of AMB series)
OFF
Output transistor
ON
Sensor
Non-detection status
Detection status
(The output is latched
(The output is latched
by the previous trigger.) by the previous trigger.)
3. A high level is established in the open state due to pull-up by the internal
circuit. (Refer to the connector wiring diagram.)
Detection status:
output transistor ON
Output
transistor
Non-detection status:
output transistor OFF
Output
(PNP output types of the AMA series)
TIMING CHART
1. Built-in oscillation circuit type
(NPN output types of the AMA series and all of AMB series)
(PNP output types of the AMA series)
ON
ON
Power supply
Power supply
OFF
Output transistor
(open collector)
OFF
OFF
Output transistor
(open collector)
ON
ON
OFF
Circuit
stability Non-detection
status
time
Detection
status
Non-detection
status
Circuit
stability Non-detection
status
time
Detection
status
Non-detection
status
Notes: 1. Circuit stability time : Max. 12 ms
2. During the time taken for the circuit to stabilize after the power is turned on, the ON/OFF status of the output transistor is not determined by whether the sensor is
in the detection status or non-detection status.
All Rights Reserved © COPYRIGHT Panasonic Electric Works Co., Ltd.
MA Motion Sensor (AMA1, AMB1, 2, 3)
2. External triggering type
ON
Tt: Min. 5ms
Power supply
OFF
Tr: Max. 5ms
VTH
VTH
External trigger
External trigger
VTL
VTL
Tw
Output transistor
(open collector)
• NPN output types
of the AMA series
• AMB series
Change
(ON to OFF or
OFF to ON)
OFF
Output
ON
Circuit
stability
time
Nondetection
status
Detection
status
Nondetection
status
Circuit
stability
time
Nondetection
status
Detection
status
Nondetection
status
ON
Output transistor
• PNP output types
of the AMA series
OFF
Notes: 1. Circuit stability time : Max. 12 ms
2. During the time taken for the circuit to stabilize after the power is turned
on, the ON/OFF status of the output transistor is not determined by
whether the sensor is in the detection status or non-detection status.
Note: The sensor recognizes at the VTH → VTL edge of an external trigger that the
external trigger has been input.
HOW TO USE
• Wiring diagram of connector
Built-in oscillation circuit type
+
Power supply
Min.
33 µF
Note 3.
External triggering type
+
+
Power supply
3
Min.
33 µF
Note 3.
+
3
Output
NPN output type
1 Note 1.
4
Tr
N.C.
(No connection)
Output
1 Note 1.
External trigger input
4
Note 2.
2
2
GND
GND
+
Power supply
Min.
33 µF
Note 3.
+
+
Power supply
3
Min.
33 µF
Note 3.
+
3
Output
PNP output type
Note 1.
4
Tr
N.C.
(No connection)
Output
Note 1.
External trigger input
Note 2.
4
1
1
2
GND
2
GND
Notes: 1. The output transistor has an open collector structure.
• Detection status: Output transistor ON (connected to GND)
• Non-detection status: Output transistor OFF (open state)
2. The status of the external trigger input is as follows:
• Open at the high level
• GND (less than 0.8V) at the low level
Under no circumstances must a high-level voltage be applied.
3. To maintain the power supply noise performance, be certain to connect a capacitor (33µF or more) to the sensor power supply input terminal in order to stabilize
the power supply voltage.
All Rights Reserved © COPYRIGHT Panasonic Electric Works Co., Ltd.
MA Motion Sensor (AMA1, AMB1, 2, 3)
REFERENCE DATA
Operating region characteristics
• How to interpret the graph
Detection distance L (mm inch)
Example: Operating area of the Short Type
with rated detection distance of
8 cm 3.150 inch.
Operating area within the dotted lines
100
3.937
90
3.543
80
3.150
70
2.756
60
2.362
50
1.969
40
1.575
30
1.181
20
.787
10
.394
0
Objects that enter the entire area are detected.
Object
Operating region for
rated detection
distance of 8 cm
3.150 inch
Operating area
within the dotted lines
Note: If only part of the object is in the detection area, it is not
detected.
Operating area within the solid lines
Objects that even partially enter the area are detected.
Object
Operating area
within the solid lines
20
0
20
.787 10
10 .787
.394 .394
Detection width W (mm inch)
Operating region for
rated detection distance
of 10 cm 3.937 inch
9 cm 3.534 inch
8 cm 3.150 inch
7 cm 2.756 inch
Reflection board
200 × 200 mm
7.874 × 7.874 inch
(reflectivity: 90%)
6 cm 2.362 inch
5 cm 1.969 inch
Y
Operating region for
rated detection distance
of 80 cm 31.496 inch
70 cm
27.559 inch
800
31.496
Reflection
board
X
700
27.559
60 cm
23.622 inch
600
23.622
Reflection board
200 × 200 mm
7.874 × 7.874 inch
(reflectivity: 90%)
500
19.685
400
15.748
50 cm
19.685 inch
40 cm
15.748 inch
Y
30 cm
11.811 inch
300
11.811
20 cm
7.874 inch
Reflection
board
200
7.874
(3) Long type (AMB34)
Detection distance L (mm inch)
100
3.937
90
3.543
80
3.150
70
2.756
60
2.362
50
1.969
40
1.575
30
1.181
20
.787
10
.394
0
(2) Middle type (AMB24)
Detection distance L (mm inch)
Detection distance L (mm inch)
(1) Thin short type (AMA14)
Short type (AMB14)
X
100
3.937
Operating region for
rated detection distance
of 200 cm 78.74 inch
2000
78.74
1750
68.898
1500
59.055
1250
49.213
150 cm
59.055 inch
Reflection board
500 × 500 mm
19.685 × 19.685 inch
(reflectivity: 90%)
1000
39.37
100 cm
39.37 inch
Y
750
29.528
500
19.685
50 cm
19.685 inch
Reflection
board
X
250
9.843
0
0
20
0
20
40
40
1.57530 .787 10
10 .787 30
1.181 .394 .394 1.181
Detection width W (mm inch)
20
0
20
40
40
1.57530 .787 10
10 .787 30
1.181 .394 .394 1.181
Detection width W (mm inch)
20
0
20
.787 10
10 .787
.394 .394
Detection width W (mm inch)
DIMENSIONS (Common to the Built-in oscillation circuit type and External triggering type)
1) Thin short type (V)
mm inch
2) Short type (H)
16
.630
5
3.2
2-RR.128
2-
6.5
.256
16.25
.640
Stamped side
(one side only)
10.0
.394
29.0
1.142
20.0
.787
10 Connector surface
.394
(Front lens surface)
11
Optical surface
.433
12.7
.500
6.6
.260
11.0
.433
Receiver
Projector
4
.157
*Rear side connector protrusion: Max. 0.4mm
22.5
.886
3.1 dia.
.122 dia.
Connector surface
(Front lens surface)
Optical surface
19.35
.762
Receiver
31.2
1.228
Projector
5
.197
14
.551
29.5
1.161
23.1
.909
6
.236
20
.787
3) Middle type (H)
22
.866
2.5 dia.
.098 dia.
0.4
.016
All Rights Reserved © COPYRIGHT Panasonic Electric Works Co., Ltd.
19.5
.768
MA Motion Sensor (AMA1, AMB1, 2, 3)
4) Long type (H)
Long type (V)
33
1.299
10
.394
4.2 dia.
.165 dia.
24.7 Connector surface
.972 (Front lens surface)
Optical surface
20
.787
10
.394
Receiver
Optical
surface
4.2 dia.
.165 dia.
7
.276 Connector
surface
55
2.165
46
65
1.811 2.559
Projector
Receiver
46
1.811
Projector
7
.276
20
.787
43
1.693
29.7
1.169 Max. 1
.039
29.7
1.169
MAX. 1
.039
WIRING DIAGRAM (Connector surface view)
4321
1) Thin short type (V)
2) Short type (H)
BM04B-SRSS
(J.S.T. Mfg. Co., Ltd.)
1: Output
2: GND
3: Power source
4. Built-in oscillation circuit type: N.C.
External triggering type:
external trigger input
1
2
3
4
IL-Z-4P-S125L3-E
(Japan Aviation Electronics Industry,
Limited)
1: Output
2: GND
3: Power source
4. Built-in oscillation circuit type: N.C.
External triggering type:
external trigger input
1
2
3
4
4) Long type (H)
3) Middle type (H)
1
2
3
4
IL-Z-4P-S125T3-E
(Japan Aviation Electronics Industry,
Limited)
1: Output
2: GND
3: Power source
4. Built-in oscillation circuit type: N.C.
External triggering type:
external trigger input
Long type (V)
IL-Z-4P-S125T3-E
(Japan Aviation Electronics Industry,
Limited)
1: Output
2: GND
3: Power source
4. Built-in oscillation circuit type: N.C.
External triggering type:
external trigger input
IL-Z-4P-S125T3-E
(Japan Aviation Electronics Industry,
Limited)
1: Output
2: GND
3: Power source
4. Built-in oscillation circuit type: N.C.
External triggering type:
external trigger input
1
2
3
4
Notes: Purchase the follwing connections:
1. Socket housing IL-Z-4S-S125C3
(Japan Aviation Electronic Industry, Ltd.)
2. Lead wire (with metal connector at one end)
OPTIONAL
mm inch
1. Connector with cable (for AMB series)
AMV9001
1. Output (Black)
2. GND (Blue)
3. Power source (Brown)
4. Built-in oscillation circuit type: N.C.
External triggering type: external trigger input (Purple)
The edge is soldered
Lead wires AWG 28
4.3
.169
6.45
.254
150±5
5.906±.197
Socket housing IL-Z-4S-S125C3
(Japan Aviation Electronics Industry, Limited)
*Connectors with cable for thin short type are handled as “U orders”.
4.5±1
.177±.039
Note: Mistaken cable assembly can cause
damage to the internal circuits, so please
check the power cord before switching
ON. (Particular care must be taken as to
avoid reverse connection of the power.)
All Rights Reserved © COPYRIGHT Panasonic Electric Works Co., Ltd.
MA Motion Sensor (AMA1, AMB1, 2, 3)
NOTES
1. Environment
1) Avoid using the sensor in
environments containing excessive
amounts of steam, dust, corrosive gas, or
where organic solvents are present.
2) When the sensor is used in noisy
environments, connect a capacitor
(minimum 33 µF) across its power input
terminals.
2. Wiring
1) Check all wiring before applying
power. Incorrect wiring may damage the
internal circuit (in particular, check that
the connection to the power supply is not
reversed.)
2) Avoid excessive removing and
replacing of the connector.
3. Detector surface (Optical surface)
1) Keep the detector surface clean.
Excessive dust or dirt on the detector
surface will deteriorate the sensing
performance.
2) Do not allow condensation or freezing
to occur on the surface of the sensor. If
condensation or freezing does occur at
low temperatures, the sensor may not
detect objects correctly.
3) This product is designed to detect the
existence of human body. The sensor will
not detect objects consisting of a low
reflective material (e.g., an object coated
with black rubber, etc.) or of a highly
reflective material (e.g., mirror, glass,
coated paper, etc.)
4) The front surface of the lens and case
are made of polycarbonate resin and can
withstand water, alcohol, oils, salts and
weak acids. Other fluids such as
alkalines, aromatic hydrocarbons and
halogenated hydrocarbons may melt or
swell the lens and case, please do not
have such fluids touch the lens and case.
5) If you use the sensor with a cover or
filter connected to the front of the sensor,
the sensor may detect the cover itself, the
detection distance can change, and
unstable operation can result.
6) When multiple sensors are to be used
side by side, please verify that there will
be no mutual interference by installing
them with the proper spacing, depending
on the type as shown below.
Model number
AMB1 series
AMA1 series
AMB2 series
AMB3 series
4. Recommended installation
procedure
Install the photoelectric sensor so that it
is orientated correctly in relation to the
pass directions of the target objects as
shown in the figure below.
Y
Z
X
Pass
directions
Object
Pass directions
Pass
directions
Object
Object
❈ → stands for pass direction of the target object.
For the general precautions, refer to the
Notes for Motion Sensors on next page.
Sensor spacing
5 cm 1.969 inch
8 cm 3.150 inch
10 cm 3.937 inch
20 cm 7.874 inch
7) To protect the inner circuit, wiring
should be max. 3 m 9.843 ft..
All Rights Reserved © COPYRIGHT Panasonic Electric Works Co., Ltd.