Philips 190G6FB/97, 190G6FB/00 User manual

Philips 190G6FB/97, 190G6FB/00 User manual
e-Manual
Philips LCD Monitor Electronic User’s Manual
file:///D|/My%20Documents/dfu/190G6/english/190g6/index.htm2005-08-23 1:18:30 PM
Safety and Troubleshooting Information
• Safety
Precautions
and
Maintenance
• Installation
Locations
• FAQs
Safety and Troubleshooting Information
Safety precautions and maintenance
WARNING: Use of controls, adjustments or procedures other than
those specified in this documentation may result in exposure to shock,
electrical hazards and/or mechanical hazards.
• Troubleshooting
• Regulatory
Information
• Other Related
Information
Read and follow these instructions when connecting and using your computer monitor:
●
●
●
●
●
●
●
●
●
●
●
●
●
●
To protect your display from possible damage, do not put excessive pressure on the LCD
panel. When moving your monitor, grasp the frame to lift; do not lift the monitor by
placing your hand or fingers on the LCD panel.
Unplug the monitor if you are not going to use it for an extensive period of time.
Unplug the monitor if you need to clean it with a slightly damp cloth. The screen may be
wiped with a dry cloth when the power is off. However, never use alcohol, solvents or
ammonia-based liquids.
Consult a service technician if the monitor does not operate normally when you have
followed the instructions in this manual.
The casing cover should be opened only by qualified service personnel.
Keep the monitor out of direct sunlight and away from stoves or any other heat source.
Remove any object that could fall into the vents or prevent proper cooling of the monitor’s
electronics.
Do not block the ventilation holes on the cabinet.
Keep the monitor dry. To avoid electric shock, do not expose it to rain or excessive
moisture.
When positioning the monitor, make sure the power plug and outlet are easily accessible.
If turning off the monitor by detaching the power cable or DC power cord, wait for 6
seconds before attaching the power cable or DC power cord for normal operation.
To avoid the risk of shock or permanent damage to the set, do not expose the monitor to
rain or excessive moisture.
IMPORTANT: Always activate a screen saver program during your application. If a still
image in high contrast remains on the screen for an extended period of time, it may leave
an 'after-image' or 'ghost image' on front of the screen. This is a well-known phenomenon
that is caused by the shortcomings inherent in LCD technology. In most cases, the
afterimage will disappear gradually over a period of time after the power has been
switched off. Be aware, that the afterimage symptom cannot be repaired and is not
covered under warranty.
Warning for lifting monitor - Do not use the area underneath the logo cover to grip or lift
the monitor. Placing weight on the logo cover can cause it to break away from the body
and cause the monitor to fall. When lifting the monitor, place one hand under the
monitor's frame.
file:///D|/My%20Documents/dfu/190G6/english/190g6/safety/safety.htm (1 of 3)2005-08-23 1:18:34 PM
Safety and Troubleshooting Information
Consult a service technician if the monitor does not operate normally when the operating
instructions given in this manual have been followed.
RETURN TO TOP OF THE PAGE
Installation Locations
●
●
●
●
●
●
Avoid exposure to heat and extreme cold.
Do not store or use the LCD monitor in locations exposed to heat, direct sunlight or
extreme cold.
Avoid moving the LCD monitor between locations with large temperature differences.
Choose a site that falls within the following temperature and humidity ranges.
❍ Temperature: 5-35°C 41-95°F
❍ Humidity: 20-80% RH
Do not subject the LCD monitor to severe vibration or high impact conditions. Do not
place the LCD monitor in the trunk of a car.
Take care not to mishandle this product by either knocking or dropping it during operation
or transportation.
Do not store or use the LCD monitor in locations where there is a high level of humidity
or in dusty environments. Do not allow water or other liquids to spill on or into the LCD
monitor.
RETURN TO TOP OF THE PAGE
file:///D|/My%20Documents/dfu/190G6/english/190g6/safety/safety.htm (2 of 3)2005-08-23 1:18:34 PM
Safety and Troubleshooting Information
file:///D|/My%20Documents/dfu/190G6/english/190g6/safety/safety.htm (3 of 3)2005-08-23 1:18:34 PM
About This Manual
• About This
Guide
• Notational
Descriptions
About This Manual
About This Guide
This electronic user's guide is intended for anyone who uses the Philips LCD Monitor. It
describes the LCD monitor's features, setup, operation and other important information. Its
contents are identical to the information in our printed version.
It includes the following sections:
●
●
●
●
●
●
●
●
Safety and Troubleshooting Information provides tips and solutions for common problems
as well as other related information you may need.
About This Electronic User's Manual gives an overview of information included, along with
notation icon descriptions and other documentation for your reference.
Product Information gives an overview of the monitor's features as well as the technical
specifications for this monitor.
Installing Your Monitor describes the initial setup process and gives an overview of how to
use the monitor.
On-Screen Display provides information on adjusting the settings on your monitor.
Customer Care and Warranty contains a list of worldwide Philips Consumer Information
Centers along with help desk phone numbers and information on the warranty applicable
to your product.
Glossary defines technical terms.
Download and Print Option transfers this entire manual to your hard drive for easy
reference.
RETURN TO TOP OF THE PAGE
Notational Descriptions
The following subsections describe notational conventions used in this document.
Notes, Cautions and Warnings
Throughout this guide, blocks of text may be accompanied by an icon and printed in bold or italic
type. These blocks contain notes, cautions or warnings. They are used as follows:
file:///D|/My%20Documents/dfu/190G6/english/190g6/about/about.htm (1 of 2)2005-08-23 1:18:36 PM
About This Manual
NOTE: This icon indicates important information and tips that help you make
better use of your computer system.
CAUTION: This icon indicates information that tells you how to avoid either
potential damage to hardware or loss of data.
WARNING: This icon indicates the potential for bodily harm and tells you how
to avoid the problem.
Some warnings may appear in alternate formats and may not be accompanied by an icon. In
such cases, the specific presentation of the warning is mandated by the relevant regulatory
authority.
RETURN TO TOP OF THE PAGE
©2005 Koninklijke Philips Electronics NV
All rights reserved. Reproduction, copying, use, modification, hiring, renting, public performance, transmission and/or
broadcasting in whole or in part is prohibited without written consent of Philips Electronics NV
file:///D|/My%20Documents/dfu/190G6/english/190g6/about/about.htm (2 of 2)2005-08-23 1:18:36 PM
Product Information
• Product
Features
Product Information
• Lead-free
Product
• Technical
Specifications
Product Features
• Resolution &
Preset Modes
190G6
• Automatic
Power Saving
● Outstanding front of screen performance
• Physical
❍ ActiveBright for brilliant colors and razor sharpness
Specification
❍ Ready to display SDTV and HDTV formats
• Pin
❍ 8-ms response time for outstanding display of moving images
Assignment
● Superior sound
• Product Views
❍ 20-watt active subwoofer for deeper bass experience
• Physical
❍ 3D virtual surround sound
Function
❍ Easy-to-use Sound Agent 2™ optimizes the audio experience
❍ Digitally transmitted PC audio
• SoundAgent™
● Maximum comfort for computainment
2 for Window
❍ High-speed USB 2.0 hub for easy connections
❍ Displays video signals from a variety of AV sources
❍ You control the settings for your favorite sound environment
● Radically cool design
❍ Concave design surrounds you with awesome entertainment
RETURN TO TOP OF THE PAGE
Lead-free Product
Philips eliminated toxic substances like lead from its displays. Lead-free display helps protect
your health and promotes environmentally sound recovery and disposal of waste from electrical
and electronic equipment.Philips complies with the European Community stringent RoHS
Directive mandating restrictions on hazardous substances in electrical and electronic equipment.
With Philips, you can be confident that your display device does not harm the environment.
Technical Specifications*
LCD PANEL
• Type
TFT LCD
• Screen size
19" / 48.3 cm diagonal
• Pixel Pitch
0.098 x 0.294 mm
file:///D|/My%20Documents/dfu/190G6/english/190g6/product/product.htm (1 of 20)2005-08-23 1:18:41 PM
Product Information
• LCD Panel type
1280 x 1024 pixels
R.G.B. vertical stripe
High gloss, hard coated
• Effective viewing area
376.3 x 301.1 mm
• Display Colors
16.2M colors
SCANNING
Vertical refresh rate
56 Hz-76 Hz
Horizontal Frequency
30k Hz-83 kHz
VIDEO
• Video dot rate
140 MHz
• Input impedance
- Video
75 ohm
- Sync
2.2K ohm
• Input signal levels
0.7 Vpp
• Sync input signal
Separate sync
Composite sync
Sync on green
• Sync polarities
Positive and negative
• Video interface
PC: D-Sub (analog) and DVI-D (digital) are available and user
selectable.
AV: Audio (L/R) for CVBS & S-Video. Audio (L/R) for YPbPr, composite
(CVBS), component (YpbPr), S-video, SCART (Europe only)
Audio
• Loudspeaker
10W Stereo Audio (5W/channel RMSx2, 250 Hz-15 kHz, 8 ohm,
THD=10%, PMPO 80 Watts)
• Headphone connector
3.5mm mini jack
• Input signal connector
3.5mm mini jack
• Stand-alone audio output
Whether there is a video display or not as long as there is an audio
input, the audio output is always functional.
Optical characteristics
• Contrast ratio
700:1 (typ.)
• Brightness
420nits
• Peak contrast angle
6 o'clock
• White Chromaticity
x: 0.283 y: 0.297 (at 9300°K)
x: 0.313 y: 0.329 (at 6500°K)
x: 0.313 y: 0.329 (at sRGB)
file:///D|/My%20Documents/dfu/190G6/english/190g6/product/product.htm (2 of 20)2005-08-23 1:18:41 PM
Product Information
• Viewing Angle (C/R>5)
• Response time
Upper 85° (typ.)
Lower 85° (typ.)
Left 85° (typ.)
Right 85° (typ.)
8 ms(typ.)
* This data is subject to change without notice.
RETURN TO TOP OF THE PAGE
Resolution & Preset Modes
• Maximum
1280 x 1024 at 75 Hz
•
Recommended
1280 x 1024 at 60 Hz
16 user definable modes
15 factory preset modes:
H. freq (kHz)
Resolution
V. freq (Hz)
31.5
640*350
70
31.5
720*400
70
31.5
640*480
60
35.0
640*480
67
37.5
640*480
75
35.2
800*600
56
37.9
800*600
60
46.9
800*600
75
49.7
832*624
75
48.4
1024*768
60
60.0
1024*768
75
69.0
1152*870
75
71.8
1152*900
76
63.9
1280*1024
60
80.0
1280*1024
75
RETURN TO TOP OF THE PAGE
file:///D|/My%20Documents/dfu/190G6/english/190g6/product/product.htm (3 of 20)2005-08-23 1:18:41 PM
Product Information
Automatic Power Saving
If you have VESA DPMS compliance display card or software installed in your PC, the monitor can
automatically reduce its power consumption when not in use. If an input from a keyboard, mouse or other input
device is detected, the monitor will 'wake up' automatically. The following table shows the power consumption
and signaling of this automatic power saving feature:
Power Management Definition
VESA Mode
Video
H-sync
V-sync
Power Used
LED color
Active
ON
Yes
Yes
Without Subwoofer
<62W
With Subwoofer
<100W
Green
Sleep
OFF
No
No
<2 W
<2 W
Amber
Switch Off
OFF
-
-
<1W
<1W
Off
This monitor is ENERGY STAR® compliant. As an ENERGY STAR® Partner, PHILIPS has determined
that this product meets the ENERGY STAR® guidelines for energy efficiency.
RETURN TO TOP OF THE PAGE
Physical Specifications
• Dimension (WxHxD) *
590 x 451 x 262.5mm (in lowest position)
• Weight
9.5 kg
• Tilt
-5° ~ 20°
• Power supply
100 — 240 VAC, 60 — 50 Hz
• Power consumption
62W without subwoofer, 100W with subwoofer
• Temperature
5° C to 35° C (operating)
-20° C to 60° C (storage)
• Relative humidity
20% to 80%
• System MTBF
50K hours (including CCFL 40K hours)
• Cabinet color
Black
* This data is subject to change without notice.
* Resolution 1280x1024, standard size, brightness max., contrast 50%, 6500° K, full white pattern, without
audio/USB.
RETURN TO TOP OF THE PAGE
file:///D|/My%20Documents/dfu/190G6/english/190g6/product/product.htm (4 of 20)2005-08-23 1:18:41 PM
Product Information
Pin Assignment
1. The digital only connector contains 24 signal contacts organized in three rows of eight contacts. Signal pin
assignments are listed in the following table:
Pin Signal
No. Assignment
Pin Signal
No. Assignment
Pin Signal
No. Assignment
1
T.M.D.S. Data2-
9
T.M.D.S. Data1-
17 T.M.D.S. Data0-
2
T.M.D.S. Data2+
10 T.M.D.S. Data1+
18 T.M.D.S. Data0+
3
T.M.D.S. Data2/4
Shield
11
4
No connect
12 No connect
20 No connect
5
No connect
13 No connect
21 No connect
6
DDC Clock
14 +5V Power
22
7
DDC Data
15 Ground (for +5V)
23 T.M.D.S. Clock+
8
No connect
16 Hot Plug Detect
24 T.M.D.S. Clock-
T.M.D.S. Data1/3
Shield
19
T.M.D.S. Data0/5
Shield
T.M.D.S. Clock
Shield
2. The 15-pin D-sub connector (male) of the signal cable:
Pin
Assignment
No.
Pin
Assignment
No.
1
Red video input
9
+5V
2
Green video input/SOG
10
Logic ground
3
Blue video input
11
Ground
4
Sense (GND)
12
Serial data line (SDA)
5
Hot Plug Detect
13
H. Sync / H+V
6
Red video ground
14
V. Sync (VCLK for DDC)
file:///D|/My%20Documents/dfu/190G6/english/190g6/product/product.htm (5 of 20)2005-08-23 1:18:41 PM
Product Information
7
Green video ground
8
Blue video ground
15
Data clock line (SCL)
RETURN TO TOP OF THE PAGE
Product Views
Follow the links to see various views of the monitor and its components.
Front View Product Description
RETURN TO TOP OF THE PAGE
Physical Function
1) Tilt
RETURN TO TOP OF THE PAGE
file:///D|/My%20Documents/dfu/190G6/english/190g6/product/product.htm (6 of 20)2005-08-23 1:18:41 PM
Product Information
Philips Sound Agent 2™
© Copyright 2005
Philips Sound Agent 2™™ and PSA2™ are trademarks of Philips Sound Solutions.
QSound™, QEM™, QSound Environment Modeling, QSound Multi-Speaker Systems, QMSS™, Q3D™,
QSurround™, QXpander™, QInteractive3D™, Audio Pix™, and the Q logo are trademarks of QSound Labs,
Inc.
EAX™ and Environmental Audio Extensions are trademarks of Creative Technology Ltd. In the United States
and other countries.
Microsoft™ and Windows™ are registered trademarks of Microsoft Corporation.
DirectX™ and DirectSound™ are trademarks of Microsoft Corporation.
All other trademarks are the property of their respective owners.
Minimum System Requirements
350 MHz CPU
64 MB RAM
One CD ROM drive
One available USB port
20 MB of available hard drive space
Windows® 2000 or Windows® XP operating system.
Please Note : Each operating system has its own minimum requirements which should be observed. In
addition, various games and DVD applications may require higher limits than listed above.
PSA2™ Software
Please install Philips SoundAgent 2™ program for audio ophimization This is included on this CD. Step-by-step
instructions are provided to guide you through the installation process. Double check on the file to start
download.
1. Introduction
The Philips Sound Agent 2 (PSA2) is a computer graphical audio control center, designed to work with Philips
Multitainment Monitors. The PSA2 utilizes the computing power of any compatible personal computer to
enhance the quality of the audio that is played either by the Audio System, or by PC resident audio players.
PSA2 includes a full suite of studio quality audio DSP processor that adds features, depth and richness to all
file:///D|/My%20Documents/dfu/190G6/english/190g6/product/product.htm (7 of 20)2005-08-23 1:18:41 PM
Product Information
audio sources.
1.1. KEY FEATURES
●
●
●
●
●
●
●
●
QInteractive3D technology offers precise 3D sound positioning with headphone and speaker output and
is compatible with DirectSound3D, EAX 1.0, EAX 2.0/I3D Level 2, and A3D enabled games.
QXpander converts ANY ordinary stereo input to virtual 3D surround sound with headphones or
speakers.
15 unique reverb environments using the exclusive QSound Environmental Modeling (QEM)
algorithms for totally immersive gaming and dramatic musical performances.
Active Dynamic Filtering found in the new QSizzle and QRumble components feature low, mid and high
frequency enrichment algorithms that help restore sonic fidelity for highly compressed digital audio files
such as MP3s and WMAs. Simply put, it makes MP3’s sound great.
QSurround creates virtual 3D surround from most of DVD movies over a two-speaker setup.
Normalization smoothes out the volume differences within audio files and reduces the volume
variations for all audio sources - automatically.
Professional style 10-Band Equalizer for precise sound tailoring of all digital audio media.
Default and user defined Presets for most settings to personalize all your games, music, and movies exactly the way you like it.
2. Software Installation
Note: To enjoy the 3D sound features the PSA2 drivers must be installed on the PC.
2.1. Installation Procedure
If you have not installed the PSA2 drivers yet, you should do so now. Insert the Installation CD that is included
in the package into the CD ROM drive. The operating system should detect the CD and automatically start the
installation process. Follow the on screen instructions to complete the installation process.
After the installation is complete, you may be asked to reboot the computer. After reboot, the Sound Agent icon
will appear in the Notification Area of the Windows Taskbar. See Figure 1. Please note that the number and
types of icons in the Notification Area varies from computer to computer.
3. Philips Sound Agent 2 Interface Operation
The following sections provide a detailed description of the PSA2 features.
3.1.Launching PSA2
Ensure that the Philips Multitainment Monitor is on and connected to the USB port of the PC. Otherwise the
PSA2 icon in the Taskbar Notification Area (normally the lower right hand corner of the screen) will indicate that
it is unavailable with a red "void" mark. See Figure 2.
If the monitor is on and connected to the PC USB Port, there should be no void mark on the PSA2 icon, and
you can double click the icon to launch the interface. See Figure 3.
file:///D|/My%20Documents/dfu/190G6/english/190g6/product/product.htm (8 of 20)2005-08-23 1:18:41 PM
Product Information
If PSA2 cannot launch it might be that the hardware is not connected, or the operating system cannot recognize
the Philips Multitainment Monitor.
If the Philips Multitainment Monitor is connected to the PC by a USB cable and the red void mark still present,
unplug the USB cable from the Monitor, wait two or three seconds and plug it back. It usually takes a few
seconds for the operating system to recognize and register the USB audio device.
When you first launch the PSA2 it appears as partially expanded form as shown in Figure 4. To reveal the Main
Control Panel click on the Drop-down arrow at the bottom side of the Visualization panel.
The panel contains three distinct sections, Compact, Main and Visual. You can reduce the expanded form to a
compact form using the Resize button. The Compact control Panel takes up very little space on the screen and
it contains the top-level controls. However, to set or change some of the settings, you need to expand to the
Main control panel. Use the Resize button when you need to expand the Main control panel again.
The Visualization Panel provides a graphic representation of the advanced audio processing features of the
PSA2. It also includes controls to enable the environmental effects. The Visualization Panel appears only in the
expanded mode as a sliding cover for the Main Control Panel.
The following sections contain detailed descriptions of the features of each panel.
3.2. Compact Control Panel
The Compact Control Panel contains the following controls:
file:///D|/My%20Documents/dfu/190G6/english/190g6/product/product.htm (9 of 20)2005-08-23 1:18:41 PM
Product Information
Master Volume
Master Volume controls the overall output level of the sound system. This volume control works independent of
the volume knob on the set. However, the bar code volume level indicator in the display screen of the Audio
System reflects any increase or decrease in volume produced by moving the master volume slider. Volume can
also be adjusted using the control on the Multitainment Monitor.
Mute
This button toggles the sound on or off to the speakers or headphones. Activating it mutes the output but does
not stop the playing of the music, regardless of the source of music. See Figure 5.
Resize
Resize Toggles between the compact mode (basic controls) and the expanded mode (for more advanced
options).
Close
Closes the PSA2 control panel without affecting audio operation.
Default
Pushing the Default button resets most PSA2 controls to a predefined functional state. All features except 3D
Effects are off.
Help
This button launches the on-line help system. It contains detail descriptions of all features of the PSA2 interface
and its operation.
Reverb
This button toggles the QSound Environmental Modeling (QEM) on or off. However, some games apply their
own environmental effects, which are not controlled by this button. Environmental modeling uses reverb
(reflected sound) and delay to create the impression that the listener is in a particular environment.
QEM provides a wide range of high-quality environmental modeling effects that are selectable from the
Visualization panel. By selecting a default environment, you impose the effects of that environment for music,
movies, or games that do not use the EAX feature.
PSA2 responds automatically to games that use the EAX and EAX2.0 commands. These games automatically
control the selection of environments (regardless of what is selected from the Visualization panel) to match
various scenes and locations, and change these selections as the environment changes. The applied intensity
of reverb is controllable by a slider in the Visualization panel. If the level of Reverb is not as expected, check
the slider in the Visualization panel and adjust properly.
QSizzle
file:///D|/My%20Documents/dfu/190G6/english/190g6/product/product.htm (10 of 20)2005-08-23 1:18:41 PM
Product Information
Toggles the QSizzle effect. When on, enhances the mid/high frequency range of a digitally compressed audio
stream. The button label illuminates when QSizzle is enabled.
QRumble
Toggles the QRumble effect. When on, it enhances the low frequency range of the audio stream. The button
label illuminates when QRumble is enabled.
Normalize
Toggles Normalization (automatic volume leveling) on or off. The button label illuminates when Normalization is
enabled.
3D Effects
Toggles 3D Effects on or off. This does not affect 3D audio games, but does affect non-3D audio games
utilizing the 2D to 3D remixing feature. The button label illuminates when 3D Effects are enabled. To enable
automatic audio features such as QSurround, and QXpander this feature must be enabled
EQ
Toggles the 10-band Equalizer on and off. The button label lights up when the Equalizer is enabled. When the
button is not activated the EQ remains inoperative.
3.3. Main Control Panel
The Main Control Panel is in the center of the expanded mode, and it provides access to advanced settings for
most PSA2 controls, which are grouped in five separate tabs. See Figure 6.
If only the Compact control panel is visible, you must expand it by clicking on the Resize button on the right
hand corner, next to the Close icon.
If the Visualization Panel is covering the Main Control Panel, slide the Visualization Panel cover down to reveal
the Main Control Panel by clicking on the arrow at the middle of the lower edge of the Visualization Panel.
Once the Main Control Panel is open, you can choose any of the tabs to select the desired set of controls. The
following is a description of each tab from left to right:
file:///D|/My%20Documents/dfu/190G6/english/190g6/product/product.htm (11 of 20)2005-08-23 1:18:41 PM
Product Information
3.3.1. Effects Tab
The Effects Tab is the first of the Main Control Panel tabs. Below is a description of all the features on the
Effects tab.
QSizzle
QSizzle is a mid and high frequency (treble) enhancement algorithm that helps to compensate for the loss of
presence, punch and signal detail that often results from compressed digital media, such as MP3 and WMA
formats.
QSizzle self-adjusts in real time according to frequency response of the input signal. This is different from the
Equalizer, which is a fixed frequency processor. The Equalizer does not monitor the input signal or perform selfadjustment. The label QSizzle Active appears in illuminated text when QSizzle is enabled, and QSizzle Off
when disabled.
QRumble
QRumble is a powerful low frequency enhancement algorithm that helps to compensate for loss of bass that
may result from compressed digital media such as MP3’s or WMA formats.
QRumble responds in real time to the varying nature of the input signal, automatically adjusting itself
accordingly. This is very different from the Equalizer, which is a static frequency processor. The Equalizer does
not monitor the input signal or perform self-adjustment.
The label QRumble Active appears in illuminated text when QRumble is enabled, and QRumble Off when
disabled.
Normalization
Normalization automatically adjusts the volume variations in various audio files or streams. Quieter signals are
amplified to match the level of louder ones, so that the listening volume maintains a consistent level. This
means that when playing files with various output levels, the need to constantly adjust your speaker volume is
minimized.
The label Normalization Active appears in illuminated text when Normalization is enabled, and Normalization
Off when disabled.
3D Effects
Three separate 3D audio enhancement algorithms are provided to maximize the spatial experience no matter
what the combination of signal type and output hardware.
When 3D Effects are enabled, the audio processor will automatically choose the appropriate algorithm (3D
mode) according to your output configuration and the type of input signal. The 3D Effects indicator LED's on
front panel and the indicators on the Effects Tab illuminate to show which algorithm is active at any given time.
QXpander
Optimizes stereo input played over speakers or headphones. When QXpander is active it provides a wider
sound field far exceeding physical position of the speakers.
QSurround
Optimizes a multi-channel source (e.g. a 5.1 channel DVD) to create "virtual" speakers and immerse the
listener in surround sound.
file:///D|/My%20Documents/dfu/190G6/english/190g6/product/product.htm (12 of 20)2005-08-23 1:18:41 PM
Product Information
3.3. 2. Equalizer Tab
The Equalizer (EQ) controls the frequency response of the system by increasing or decreasing the frequency
response of ten independent frequency bands.
This Equalizer works very much the same as the equalizers in high quality sound systems. Each slider controls
the relative level of a band (range) of frequencies. The number listed above each slider column is the center
frequency of the band controlled by that slider. When a slider is set to the center position, frequencies within
this band left flat and the gain is 0dB. See Figure 7.
To boost the level of a given band, move its slider above the centerline. To cut the relative level of a given
band, move its slider below the centerline. Maximum boost or cut is ± 12dB on each frequency level.
Sliders can be individually centered by right clicking anywhere within the slider area, or collectively by clicking
the Reset button on top right corner of the panel. Clicking the default button on the compact panel can also
collectively center the sliders. Please note that the default button resets several other features as well.
3.3.3. Setup Tab
Speaker Test Utility
The Speaker Test Utility can be used to verify that speakers and/or headphones are operating properly.
file:///D|/My%20Documents/dfu/190G6/english/190g6/product/product.htm (13 of 20)2005-08-23 1:18:41 PM
Product Information
The test utility highlights each speaker that is being tested. See Figure 8. Click any speaker icon to send the
test sound to the corresponding speaker. If headphones are plugged in, the speaker icons are grayed out and
you can click the left or right headphone icon instead.
The Loop test button allows the test to repeat until the Stop button is pressed. If the Loop is off, the sound will
play once for each click of a speaker or headphone icon.
The Auto button sends the test sound to each output once and then moves to the next one automatically. If the
Loop and the Auto buttons are used in conjunction, the test signal will loop through the available outputs until
the Stop button is pressed.
Preamp Slider
The Preamp Level control allows you to boost the input audio signal before it is processed by the PSA2. It has
a similar effect as the master volume, but should not be used instead of it.
NOTE: Increasing the PreAmp may cause audio distortion on some high level input signals. In some cases, an
input signal can be of such amplitude that audio distortion can occur at the preamp default level. If this is the
case simply lower the preamp level to help eliminate any distortion.
Subwoofer Slider
The Subwoofer Level control enables you to set the level of the derived Subwoofer output relative to the left
and right speakers.
Balance Slider
This slider allows you to adjust the balance between left and the right speakers or headphones. For best 3D
effects it should normally be left in the center. Right-click the slider to center it.
3.3.4. Mixer Tab
The Mixer Tab allows you to control playback and recording sources. Two sub-tabs at the bottom of the Mixer
screen provide access to Playback or Recording controls.
3.3.4.1. Source controls
When the Playback Sub-tab is selected, you can individually mute or un-mute as many playback sources as
you wish using the Mute buttons.
When the Recording Sub-tab is selected, you must select the single source you wish to record by clicking its
Select button. See Figure 9.
Volume sliders set the level for each source.
Balance sliders adjust the relative left and right output levels for each stereo source. Balance sliders should
normally be left in the center, the default position. Right-click any of the balance sliders to center it.
file:///D|/My%20Documents/dfu/190G6/english/190g6/product/product.htm (14 of 20)2005-08-23 1:18:41 PM
Product Information
When playing audio CD’s using the CD ROM driver of the PC, one should enable the digital audio extraction in
the system device manager. If you need more information refer to the TroubleShooting section in Appendix C
of this document.
3.3.5. Presets Tab
The Preset functions enable you to make snapshots of the state of all Philips Sound Agent 2 controls, so that
you can conveniently reload the same settings at any time.
file:///D|/My%20Documents/dfu/190G6/english/190g6/product/product.htm (15 of 20)2005-08-23 1:18:41 PM
Product Information
The Preset system enables you to save the state of PSA2 controls once you have made adjustments to
customize your listening experience, so you can recall settings for any source and playback environment.
For example, if you have been listening to music with predominant drums and bass and have adjusted the
controls to suit your taste, you can quickly save a preset called “Drums’n’Bass”. Whenever you listen to this
type of music again, simply load this preset, and all the controls will return to the settings you had in effect when
you saved it.
Sound Agent 2 comes with four factory presets as listed on the Presets tab.The Multitainment Monitor has four
buttons that also enable you to select the factory Presets. The following is a description of each feature on the
Presets tab.
Load
Clicking on this button loads an existing preset. To load another preset, highlight it on the list and click the
Load.
Save
When you load one of your presets and make changes to it, you can save it by clicking on the Save button. If
you have selected one of the factory presets and made changes to it, you will have to save it under a different
name. Sound Agent 2 will not overwrite factory presets, but you can overwrite your own unique presets.
Save As
You can load an existing preset (factory or one of yours), modify it to your taste, and save it as a new preset.
Delete
Deletes the selected preset permanently from the list. When you select one your presets and click on this
button, a confirmation dialog box will appear and when you confirm by clicking the OK button, the preset will be
removed from the list. This button will not delete any of the factory presets.
3.3.6. Info Tab
This tab contains useful information regarding the product. It includes the software driver's version number,
manufacturer’s name, and web page addresses.
file:///D|/My%20Documents/dfu/190G6/english/190g6/product/product.htm (16 of 20)2005-08-23 1:18:41 PM
Product Information
3.4. Visualization Panel
The Visualization Panel provides a graphical representation of the environments and effects that are created by
Sound Agent 2. It also contains two drop-down menus and the Reverb Intensity Slider.
The drop-down menu on the right contains sixteen different reverb environmental effects to select. To select a
reverb environment, the Reverb button located on the Compact Control Panel must be enabled.
The drop-down menu on the left contains all factory and user defined presets for various types of music. This
menu allows easy preset access via the Visualization Control Panel.
The top center horizontal slider controls the intensity of the reverb effect that is being applied. Adjust as
necessary to achieve the right amount of Reverb based on individual content.
The Visualization Panel may be moved up and down to conceal or reveal the Main Control Panel by clicking the
arrow at the bottom center of the panel.
file:///D|/My%20Documents/dfu/190G6/english/190g6/product/product.htm (17 of 20)2005-08-23 1:18:41 PM
Product Information
4. Uninstalling PSA2
If for any reason it becomes necessary to uninstall the PSA2 drivers, you can choose one of two available
methods. You may go to the system control panel and launch the "Add/Remove Programs" utility. From the list
of programs find PSA2 (or Philips Sound Agent 2) and click on it so it is highlighted. Click the "Change/
Remove" button.
Or, you may choose the uninstall program that comes with PSA2 program. For this you click on the Windows
Start button, click on the "Programs", ("All Programs" in XP), click on the Philips folder, then select and execute
the Philips Uninstall program.
5. Technical Support And Warranty
Before calling the technical support number please make sure you have the following information available:
●
●
●
●
Model number and date of purchase.
Computer type, processor speed, and memory available.
Computer operating system (IE; Windows® 2000, or XP).
On-screen error information.
5.1. Internet Address:
Useful information such as the latest drivers and products can be found at:
The web site for Europe is:
http://www.philips.com/sound
Philips general web site is:
http://www.philips.com/ce
5.2. Technical Support Information:
Refer to the Product Warranty card provided for technical support contact information.
6. Appendix A,TroubleShooting
This appendix covers some of the basic mistakes and pitfalls you might encounter.
No Sound is coming out
1. Check the mute button to ensure it is deactivated.
2. Check the volume knob and turn it up.
3. Click on default button on the PSA2 compact panel.
System Error Message
When attempting to launch an audio player application, on a rare occasion you may see one of the following
error messages depending on the operating system of the PC. This error message also causes no audio to be
played.
file:///D|/My%20Documents/dfu/190G6/english/190g6/product/product.htm (18 of 20)2005-08-23 1:18:41 PM
Product Information
Windows XP
Windows 2000
Figure 13
This error message is generated due to lack of sufficient bandwidth on the USB hub that the Audio System is
plugged into. If you have a USB imaging device (such as a webcam or a scanner) and you have an imaging
application open, and try to open an audio player application such as Winamp or Windows Media Player.
Solution
Click "Close" or "No" depending of which error message you have.
Close the audio player application.
Close the imaging application.
Reopen the audio player application and play the audio stream.
No Audio When Playing Audio CD in the CD Drive
The system CD ROM drive could be used to play audio CD's. However, the Audio Digital Extraction feature of
the PC should be enabled. Here are the steps to enable this feature:
Windows 2000
1. Right click on "My Computer". On Windows 2000 this icon on desktop. On Windows XP it is in the upper
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
right portion of the Start menu.
Scroll down to "Properties" and click on it.
Click on "Hardware" tab.
Click on "Device Manager" button at the middle of panel.
Click on the + sign next to the DVD/CD-ROM Drives.
Right click on the CD ROM drive that appears. If there are more than one CD ROM drives, click on the
one that is being used for audio CD playing.
Scroll down to "Properties" and click on it.
A new panel opens. See Figure 14
Click on the Properties tab
Click to select the box with the label “Enable digital CD for this CD-ROM device
Click the OK button and close all the relating windows.
file:///D|/My%20Documents/dfu/190G6/english/190g6/product/product.htm (19 of 20)2005-08-23 1:18:41 PM
Product Information
CD Player Control in the mixer playback tab does not have any effects on the output when Playing
Audio CD in the CD Drive
Because the CD player sends the audio streams via the digital data lines, Windows treats this source like other
digital audio sources such as MP3 files. Therefore, to control the volume and balance use the controls for
“wave”.
No PSA2 Icon in the Notification Area
After you have installed PSA2 from the installation CD, if the PSA2 icon disappears from the Notification Area,
go to the start menu, click on Programs (Windows 2000 or Windows XP), click on Philips, then click on Sound
Agent 2, then click on Control Panel.
file:///D|/My%20Documents/dfu/190G6/english/190g6/product/product.htm (20 of 20)2005-08-23 1:18:41 PM
Installing Your LCD Monitor
Installing Your LCD Monitor
product
•
Description
Connecting
•
to Your PC Product Description
Getting
•
Started
Optimizing
•
Performance
1
To switch display's power On & Off
2
Power LED
3
To access OSD menu
4
To adjust the OSD (Up, Down, Left, Right)
5
Automatically adjust horizontal position, vertical position, phase and clock
setting in D-sub only
6
To adjust the speaker volume
7
To mute the audio
8
Preset hotkeys to optimize audio performance
9
To adjust the subwoofer bass
10 USB Audio LED
20 Antenna
11 DVI-D
21 USB upstream port
12 D-Sub
22 Monitor DC in
13 PC audio
23 Subwoofer out
file:///D|/My%20Documents/dfu/190G6/english/190g6/install/install.htm (1 of 2)2005-08-23 1:18:44 PM
Installing Your LCD Monitor
14 HD audio jack
24 Microphone in
15 YPbPr
25 Headphone out
16 S-Video
26 USB hub
17 Kensington lock
27 Subwoofer power
18 CVBS
28 Subwoofer in
19 Audio jack
29 SCART
RETURN TO TOP OF THE PAGE
Optimizing Performance
For best performance, ensure that your display settings are set at 1280x1024, 60Hz.
RETURN TO TOP OF THE PAGE
file:///D|/My%20Documents/dfu/190G6/english/190g6/install/install.htm (2 of 2)2005-08-23 1:18:44 PM
On-Screen Display
On-Screen Display
• Description
of the OnScreen
Display
The OSD
•
Tree
Description of the On Screen Display
What is the On-Screen Display?
• SmartControl
• Q&A
On-Screen Display (OSD) is a feature in all Philips LCD monitors. It allows an end user to adjust screen performance
or select functions of the monitors directly through an on-screen instruction window. A user friendly on screen display
interface is shown as below :
Basic and simple instruction on the control keys.
buttons at the base of the monitor to move the cursor,
In the OSD shown above users can press
confirm the choice or change, and
to
to adjust/select the change.
RETURN TO TOP OF THE PAGE
The OSD Tree
Below is an overall view of the structure of the On-Screen Display. You can use this as a reference when you want to
work your way around the different adjustments later on.
file:///D|/My%20Documents/dfu/190G6/english/190g6/osd/osddesc.htm (1 of 6)2005-08-23 1:18:47 PM
On-Screen Display
file:///D|/My%20Documents/dfu/190G6/english/190g6/osd/osddesc.htm (2 of 6)2005-08-23 1:18:47 PM
On-Screen Display
file:///D|/My%20Documents/dfu/190G6/english/190g6/osd/osddesc.htm (3 of 6)2005-08-23 1:18:47 PM
On-Screen Display
file:///D|/My%20Documents/dfu/190G6/english/190g6/osd/osddesc.htm (4 of 6)2005-08-23 1:18:47 PM
On-Screen Display
file:///D|/My%20Documents/dfu/190G6/english/190g6/osd/osddesc.htm (5 of 6)2005-08-23 1:18:47 PM
On-Screen Display
Note: sRGB is a standard for ensuring correct exchange of colors between different devices (e.g. digital cameras,
monitors, printers, scanners, etc.)
Using a standard unified color space, sRGB will help represent pictures taken by an sRGB compatible device
correctly on your sRGB enabled Philips monitors. In that way, the colors are calibrated and you can rely on the
correctness of the colors shown on your screen.
Important with the use of sRGB is that the brightness and contrast of your monitor is fixed to a predefined setting as
well as the color gamut. Therefore it is important to select the sRGB setting in the monitor's OSD.
To do so, open the OSD by pressing the OK button on the side of your monitor. Move the down button to go to Color
and press OK again. Use the right button to go to sRGB. Then move the down button and press OK again to exit the
OSD.
After this, please do not change the brightness or contrast setting of your monitor. If you change either of these, the
monitor will exit the sRGB mode and go to a color temperature setting of 6500K.
RETURN TO TOP OF THE PAGE
file:///D|/My%20Documents/dfu/190G6/english/190g6/osd/osddesc.htm (6 of 6)2005-08-23 1:18:47 PM
Customer Care & Warranty
Customer Care & Warranty
PLEASE SELECT YOUR COUNTRY/AREA TO REVIEW DETAILS OF YOUR
WARRANTY COVERAGE
WESTERN EUROPE: Austria • Belgium • Cyprus • Denmark • France • Germany • Greece •
Finland • Ireland • Italy • Luxembourg • the Netherlands • Norway • Portugal • Sweden •
Switzerland • Spain • United Kingdom
EASTERN EUROPE: Czech Republic • Hungary • Poland • Russia • Slovakia • Slovenia •
Turkey
LATIN AMERICA: Antilles • Argentina • Brasil • Chile • Colombia • Mexico • Paraguay •
Peru • Uruguay • Venezuela
NORTH AMERICA: Canada • USA
PACIFIC: Australia • New Zealand
ASIA: Bangladesh • China • Hong Kong • India • Indonesia • Japan • Korea • Malaysia •
Pakistan • Philippines • Singapore • Taiwan • Thailand
AFRICA: Morocco • South Africa
MIDDLE EAST: Dubai • Egypt
file:///D|/My%20Documents/dfu/190G6/english/warranty/warranty.htm2005-08-23 1:18:49 PM
Glossary
Glossary
ABCDEFGHIJKLMNOPQRSTUVWXYZ
A
ActiveBright
The ActiveBright delivers high definition TV-like quality by displaying brilliant, razor sharp colors and
a wide viewing angle for the very best in multimedia entertainment.
Active matrix
This is a kind of liquid crystal display structure in which switching transistors are attached to each
pixel to control the on/off voltage. It produces a brighter and sharper display with a broader viewing
angle than a passive matrix display. Also refer to TFT (thin film transistor).
Amorphous silicon (a-Si)
A semiconductor material that is used to make the thin film transistors (TFTs) layer of an active
matrix LCD.
Aspect ratio
The width-to-height ratio of the active area of a display. In general, most monitors have an aspect
ratio of 4:3 or 5:4. Wide monitors or TVs have an aspect ratio of 16:9 or 16:10.
RETURN TO TOP OF THE PAGE
B
Brightness
The dimension of color that is referred to an achromatic scale, ranging from black to white, also
called lightness or luminous reflectance. Because of confusion with saturation, the use of this term
file:///D|/My%20Documents/dfu/190G6/english/190g6/glossary/glossary.htm (1 of 10)2005-08-23 1:18:53 PM
Glossary
should be discouraged.
RETURN TO TOP OF THE PAGE
C
CCFL(cold cathode fluorescent light)
These are the fluorescent light tubes providing the light for the LCD module. These tubes are
generally very thin, approximately 2 mm in diameter.
Chromaticity
That part of color specification, which does not involve illuminance. Chromaticity is two-dimensional
and specified by pairs of numbers such as dominant wavelength and purity.
CIE (Commission International de I'Eclairage)
The International Commission on Illumination, the primary international organization concerned with
color and color measurement.
Color temperature
A measurement of the color of light radiated by an object while it is being heated. This
measurement is express in terms of absolute scale, (degrees Kelvin). Lower Kelvin temperatures
such as 2400° K are red; higher temperatures such as 9300° K are blue. Neutral temperature is
white, at 6504° K. Philips monitors generally offers 9300° K, 6500° K, and user define.
Contrast
The luminance variation between light and dark areas in an image.
Contrast ratio
The ratio of luminance between the brightest white pattern and the darkest black pattern.
Component Video
file:///D|/My%20Documents/dfu/190G6/english/190g6/glossary/glossary.htm (2 of 10)2005-08-23 1:18:53 PM
Glossary
Offers best possible picture quality in the analogue domain. Maximum band width through R (red),
G (green) and B (blue) signals.
Composite Video
A variety of format choices in connecting video devices.
RETURN TO TOP OF THE PAGE
D
Dual Input
Dual input provides connectors to accommodate input of both analog VGA and digital DVI signals.
D-SUB
A VGA Analog input connector. Your monitor comes with a D-Sub cable.
Digital Visual Interface (DVI)
The Digital Visual Interface (DVI) specification provides a high-speed digital connection for visual
data types that is display technology independent. The interface is primarily focused at providing a
connection between a computer and its display device. The DVI specification meets the needs of all
segments of the PC industry (workstation, desktop, laptop, etc.) and will enable these different
segments to unite around one monitor interface specification.
The DVI interface enables:
1.
2.
3.
4.
Reduce signal loss and video noise in signal due to less signal conversion.
Independent from display technology, and can be used on LCD, Plasma, LCOS, etc.
Plug and play through hot plug detection, EDID and DDC2B.
Digital and Analog support in a single connector (DVI-I only).
file:///D|/My%20Documents/dfu/190G6/english/190g6/glossary/glossary.htm (3 of 10)2005-08-23 1:18:53 PM
Glossary
RETURN TO TOP OF THE PAGE
E
Embedded Power Supply
An embedded power supply is a power adaptor built into the body of a display device that replaces
a bulky external power adaptor.
Energy Star Computers Program
An energy conservation program launched by the US Environmental Protection Agency (EPA),
promotes the manufacture and marketing of energy-efficient office automation equipment.
Companies joining this program, must be willing to commit themselves to manufacture one or more
products capable of going into a low -power state (< 30 W) either after a period of inactivity, or after
a predetermined time selected by the user.
RETURN TO TOP OF THE PAGE
G
Gamma
Screen luminance as a function of video voltage approximately follows a mathematical power
function of the input video signal, the exponent of which is called gamma.
Grayscale
An achromatic scale ranging from black through a series of successively lighter grays to white.
Such a series may be made up of steps, which appear to be equally distant from one another. If the
Analog/ Digital converter is 8 bit, then the monitor can display at most 28 = 256 levels. For a color
monitor, R.G.B. each color hads 256 levels. Thus, total color can display is 256x256x256= 16.7
million.
file:///D|/My%20Documents/dfu/190G6/english/190g6/glossary/glossary.htm (4 of 10)2005-08-23 1:18:53 PM
Glossary
RETURN TO TOP OF THE PAGE
H
High Brightness Panel
Allows daylight viewing even in large rooms with high ambient light conditions.
HDTD
HDTV delivers exceptional picture quality and real movie-viewing experience that makes television
more dynamic, truer than anything you've seen before. It is the latest and best television signal
available. It features picture quality more than twice that of traditional analog broadcasts. In order to
effectively maximize the HDTV signal, a television must incorporate advanced signal input
connectivity and circuitry design. To use HDTV the TV must be connected via its component video
or DVI inputs to a DTV set-top box and set to operate in the DTV mode.
Hue
The main attribute of a color that distinguishes it from other colors. For example, a color may have a
green, yellow, or purple hue. Color defined as having hue are know as chromatic colors. White,
black, and grays possess no hue.
RETURN TO TOP OF THE PAGE
I
IPS (In Plane Switching)
A technique of improving the viewing angle of an LCD where the liquid crystal molecules are
switched in the plane of the LCD layer rather than vertical to it.
RETURN TO TOP OF THE PAGE
L
LCD (liquid crystal display)
file:///D|/My%20Documents/dfu/190G6/english/190g6/glossary/glossary.htm (5 of 10)2005-08-23 1:18:53 PM
Glossary
A display composed of liquid crystal suspended between two transparent sheets. The display is
composed thousands of pixels which can be turned on or off with electrical stimulation. Thus,
colorful images/texts can be generated.
Liquid crystal
The compound found in liquid crystal displays. Liquid crystal reacts predictably when electrically
stimulated. This makes it the ideal compound to turn LCD pixels "on" or "off." Liquid crystal is
sometimes abbreviated as LC.
Luminance
A measure of the brightness or luminous intensity of light, usually expressed in units of Candelas
per square meter (cd/m2) or foot Lamberts. 1 fL=3.426 cd/m2.
RETURN TO TOP OF THE PAGE
N
Nit
A unit of luminance equal to 1 cd/m2 or 0.292 ftL.
RETURN TO TOP OF THE PAGE
P
Pixel
Picture Element; the smallest element on a computerized CRT or LCD image, and hence a display.
Polarizer
A light filter which only allows light waves of a certain rotation through. Polarized material with
file:///D|/My%20Documents/dfu/190G6/english/190g6/glossary/glossary.htm (6 of 10)2005-08-23 1:18:53 PM
Glossary
perpendicular filtering is used in LCDs to enclose the liquid crystal. The liquid crystal is then used
as the medium which twists the light waves 90° in order to allow the light to pass through or not.
RETURN TO TOP OF THE PAGE
R
Refresh rate
The number of times per second the screen is refreshed or redrawn. This number is usually stated
in Hz (Hertz) or cycles per second. A rate of 60 Hz is equal to 60 tomes per second.
Response Time
Response time is the period required for a liquid crystal cell to go from active (black) to inactive
(white) and back to active (black) again. It is measured in milliseconds. Faster is better: Lower
response time means faster transitions and, therefore, results in fewer visible image artifacts in the
display of fast-moving images.
RETURN TO TOP OF THE PAGE
S
SCART
Enable connection to TV and other source (DVD+RW/VCR).
SDTV
A display device ready to display standard definition television and high definition television signals,
which are commonly used by TV systems in the world.
SoundAgent2
TM
Sound Agent 2 is intelligent software with a fun and easy-to-use graphical interface. The Sound
Agent takes the confusion out of PC audio by automatically optimizing the sound for all popular
formats. It also allows you to fine-tune the performance to fit in with your personal audio tastes.
Stand-alone audio function
file:///D|/My%20Documents/dfu/190G6/english/190g6/glossary/glossary.htm (7 of 10)2005-08-23 1:18:53 PM
Glossary
Built-in advanced firmware that delivers audio output from external audio devices including a
portable tape, CD or MP3 player even when there is no video input.
Subwoofer
A subwoofer is a speaker that reproduces the lower end of the audio spectrum. The monitor has a
separate subwoofer that is optimized to reproduce bass frequencies and satellite speakers that are
optimized for mid- and high-range frequencies. The result is a system that powerfully reproduces
the full range of audio frequencies from deep bass to crystal clear high notes with the minimum of
distortion.
sRGB
sRGB is a standard for ensuring correct exchange of colors between different devices (e.g. digital
cameras, monitors, printers, scanners, etc.)
Using a standard unified color space, sRGB will help represent pictures taken by an sRGB
compatible device correctly on your sRGB enabled Philips monitors. In that way, the colors are
calibrated and you can rely on the correctness of the colors shown on your screen.
Important with the use of sRGB is that the brightness and contrast of your monitor is fixed to a
predefined setting as well as the color gamut. Therefore it is important to select the sRGB setting in
the monitor's OSD.
To do so, open the OSD by pressing the OK button on the side of your monitor. Move the down
button to go to Color and press OK again. Use the right button to go to sRGB. Then move the down
button and press OK again to exit the OSD.
After this, please do not change the brightness or contrast setting of your monitor. If you change
either of these, the monitor will exit the sRGB mode and go to a color temperature setting of 6500K.
Other:
USB plug: An upstream and a downstream USB plug is provide for user's convenience.
RETURN TO TOP OF THE PAGE
T
TFT(thin film transistor)
Usually made from amorphous silicon (a-Si) and used as a switch to a charge storage device
located below each sub-pixel on an active matrix LCD.
RETURN TO TOP OF THE PAGE
file:///D|/My%20Documents/dfu/190G6/english/190g6/glossary/glossary.htm (8 of 10)2005-08-23 1:18:53 PM
Glossary
U
USB or Universal Serial Bus
The universal serial bus or USB is a standard protocol for linking PCs and peripherals. Because it
delivers high speed at a low cost, USB has become the most popular method for connecting
peripheral devices to a computer. A USB 2.0 port located on a monitor directly in the user's line of
sight provides easy, high-speed connectivity for USB devices at a convenient location.
RETURN TO TOP OF THE PAGE
V
Vertical refresh rate
Expressed in Hz, it is the number of frames (complete pictures) written to the screen every second.
RETURN TO TOP OF THE PAGE
Y
YPbPr
Component video is a technique for recording and transmitting of video in which each color is
maintained in a separate channel. RGB is an example of component video using one channel each
for red (R), green (G) and blue (B). It is the way to connect a DVD player for optimum picture quality.
RETURN TO TOP OF THE PAGE
file:///D|/My%20Documents/dfu/190G6/english/190g6/glossary/glossary.htm (9 of 10)2005-08-23 1:18:53 PM
Glossary
file:///D|/My%20Documents/dfu/190G6/english/190g6/glossary/glossary.htm (10 of 10)2005-08-23 1:18:53 PM
Download and Print
Download and Print
• Installing
your LCD
monitor
driver
Installing Your LCD monitor driver
• Download
and
System requirements:
Printing
Instructions
● PC running Windows 95, Windows® 98, Windows® 2000 , Windows® Me, Windows® XP
or later
Installing
● Find your driver ".inf/.icm/.cat" at : lcd\pc\drivers
• FPadjust
Program
Read the "Readme.txt" file before installing.
This page provides an option to read the manual in .pdf format. PDF files can be downloaded into
your hard disk, then viewed and printed with Acrobat Reader or through your browser.
If you do not have Adobe® Acrobat Reader installed, click on the link to install the application.
Adobe® Acrobat Reader for PC / Adobe® Acrobat Reader for Mac.
Download instructions:
To download the file:
1. Click-and-hold your mouse over the icon below. (Windows® 95/98/2000/Me/XP users rightclick)
Download
190G6.pdf
Download
PSA2 User Guide.pdf
2. From the menu that appears, choose 'Save Link As...', 'Save Target As...' or 'Download Link to
Disk'.
3. Choose where you would like to save the file; click 'Save' (if prompted to save as either 'text' or
'source', choose 'source').
file:///D|/My%20Documents/dfu/190G6/english/download/download.htm (1 of 3)2005-08-23 1:18:56 PM
Download and Print
Printing instructions:
To print the manual:
1. With the manual file open, follow your printer's instructions and print the pages you need.
RETURN TO TOP OF THE PAGE
Installing FPadjust Program
The FP Adjust program generates alignment patterns which will help you adjust monitor settings
such as CONTRAST, BRIGHTNESS, HORIZONTAL & VERTICAL POSITION, PHASE and
CLOCK.
System requirements:
●
PC running Windows® 95, Windows® 98, Windows® 2000, Windows® Me, Windows®
XP or later
To install FPadjust Program:
●
●
Click on the link or icon to install FPadjustment Program.
or
Click-and-hold your mouse over the icon. (Win95/98/2000/Me/XP users right-click)
Download
●
●
●
FP_setup04.exe
From the menu that appears, choose 'Save Link As...', 'Save Target As...' or 'Download
Link to Disk'.
Choose where you would like to save the file; click 'Save' (if prompted to save as either
'text' or 'source', choose 'source').
Exit your browser and install the FPadjust Program.
Read the "FP_Readme04.txt" file before installing.
file:///D|/My%20Documents/dfu/190G6/english/download/download.htm (2 of 3)2005-08-23 1:18:56 PM
Download and Print
RETURN TO TOP OF THE PAGE
file:///D|/My%20Documents/dfu/190G6/english/download/download.htm (3 of 3)2005-08-23 1:18:56 PM
FAQs (Frequently Asked Questions)
• Safety and
Troubleshooting
• General FAQs
• Screen
Adjustments
• Compatibility
with Other
Peripherals
• LCD Panel
Technology
• Ergonomics,
Ecology and
Safety
Standards
• Troubleshooting
• Regulatory
Information
• Other Related
Information
FAQs (Frequently Asked Questions)
General FAQs
Q: When I install my monitor what should I do if the screen shows 'Cannot display this video
mode'?
A: Recommended video mode for Philips 19": 1280x1024 @60Hz.
1. Unplug all cables, then connect your PC to the monitor that you used previously.
2. In the Windows Start Menu, select Settings/Control Panel. In the Control Panel Window,
3.
4.
5.
6.
select the Display icon. Inside the Display Control Panel, select the 'Settings' tab. Under the
setting tab, in box labeled 'desktop area', move the slidebar to 1280x1024 pixels (19").
Open 'Advanced Properties' and set the Refresh Rate to 60Hz, then click OK.
Restart your computer and repeat step 2 and 3 to verify that your PC is set at
[email protected] (19").
Shut down your computer, disconnect your old monitor and reconnect your Philips LCD
monitor.
Turn on your monitor and then turn on your PC.
Q: What does 'refresh rate' mean in connection with an LCD monitor?
A: The refresh rate is of much less relevance for LCD monitors. LCD monitors display a
stable, flicker-free image at 60Hz. There is no visible difference between 85Hz and 60Hz.
Q: What are the .inf and .icm files on the CD-ROM? How do I install the drivers (.inf and .
icm)?
A: These are the driver files for your monitor. Follow the instructions in your user manual to
install the drivers. Your computer may ask you for monitor drivers (.inf and .icm files) or a
driver disk when you first install your monitor. Follow the instructions to insert the
( companion CD-ROM) included in this package. Monitor drivers (.inf and .icm files) will be
installed automatically.
Q: How do I adjust the resolution?
A: Your video card/graphic driver and monitor together determine the available resolutions.
You can select the desired resolution under Windows® Control Panel with the "Display
properties".
file:///D|/My%20Documents/dfu/190G6/english/190g6/safety/saf_faq.htm (1 of 7)2005-08-23 1:19:08 PM
FAQs (Frequently Asked Questions)
Q: What if I get lost when I am making monitor adjustments?
A: Simply press the OSD button, then select 'Factory Reset' to recall all of the original
factory settings.
Q: What is the Auto function?
A: The AUTO adjustment key restores the optimal screen position, phase and clock settings
at the press of a single button – without the need to navigate through OSD menus and
control keys.
Q: My Monitor has no power (Power LED does not light up). What should I do?
A: Make sure the AC power cord is connected to the Monitor.
Q: Will the LCD monitor accept an Interlace signal?
A: No. If an Interlace signal is used, the screen displays both odd and even horizontal
scanning lines at the same time, thus distorting the picture.
Q: What does the Refresh Rate mean for LCD?
A: Unlike CRT display technology, in which the speed of the electron beam is swept from
the top to the bottom of the screen determines flicker, an active matrix display uses an
active element (TFT) to control each individual pixel and the refresh rate is therefore not
really applicable to LCD technology.
Q: Will the LCD screen be resistant to scratches?
A: A protective coating is applied to the surface of the LCD, which is durable to a certain
extent (approximately up to the hardness of a 2H pencil). In general, it is recommended that
the panel surface is not subject to any excessive shocks or scratches. An optional
protective cover with greater scratch resistance is also available.
Q: How should I clean the LCD surface?
file:///D|/My%20Documents/dfu/190G6/english/190g6/safety/saf_faq.htm (2 of 7)2005-08-23 1:19:08 PM
FAQs (Frequently Asked Questions)
A: For normal cleaning, use a clean, soft cloth. For extensive cleaning, please use isopropyl
alcohol. Do not use other solvents such as ethyl alcohol, ethanol, acetone, hexane, etc.
RETURN TO TOP OF THE PAGE
Screen Adjustments
Q: What is the FPadjust program on the CD-ROM?
A: The FPadjust program generates alignment patterns that help you adjust monitor settings
such as Contrast, Brightness, Horizontal Position, Vertical Position, Phase and Clock for
optimal performance.
Q: When I install my monitor, how do I get the best performance from the monitor?
A:
1. For best performance, make sure your display settings are set at [email protected] for 19".
2. To install the Flat Panel Adjust (FPadjust) program located on the monitor setup CD-ROM,
open the CD-ROM and double-click the FP_setup04.exe icon. This will install FP Adjust
automatically and place a shortcut on your desktop.
3. Run FPadjust by double clicking the shortcut. Follow the instructions step by step to optimize
image performance with your system's video controller.
Q: How do LCDs compare to CRTs in terms of radiation?
A: Because LCDs do not use an electron gun, they do not generate the same amount of
radiation at the screen surface.
RETURN TO TOP OF THE PAGE
Compatibility with other Peripherals
Q: Can I connect my LCD monitor to any PC, workstation or Mac?
A: Yes. All Philips LCD monitors are fully compatible with standard PCs, Macs and
workstations. You may need a cable adapter to connect the monitor to your Mac system.
Please contact your dealer/retailer for more information.
file:///D|/My%20Documents/dfu/190G6/english/190g6/safety/saf_faq.htm (3 of 7)2005-08-23 1:19:08 PM
FAQs (Frequently Asked Questions)
Q: Are Philips LCD monitors Plug-and-Play?
A: Yes, the monitors are Plug-and-Play compatible with Windows® 95, 98, 2000 and XP.
RETURN TO TOP OF THE PAGE
LCD Panel Technology
Q: What is a Liquid Crystal Display?
A: A Liquid Crystal Display (LCD) is an optical device that is commonly used to display
ASCII characters and images on digital items such as watches, calculators, portable game
consoles, etc. LCD is the technology used for displays in notebooks and other small
computers. Like light-emitting diode and gas-plasma technologies, LCD allows displays to
be much thinner than cathode ray tube (CRT) technology. LCD consumes much less power
than LED and gas-displays because it works on the principle of blocking light rather than
emitting it.
Q: How are LCDs made?
A: LCDs are created from two glass plates separated from each other at a distance of a few
microns. The plates are filled with liquid crystal and then sealed together. The top plate is
colored with an RGB pattern to make the color filter. Polarizers are then glued to both plates.
This combination is sometimes called 'glass' or 'cell.' The LCD cell is assembled into a
'module' by adding the backlight, driver electronics and frame.
Q: What is polarization ?
A: Polarization is basically directing light to shine in one direction. Light is electromagnetic
waves. Electric and magnetic fields oscillate in a direction perpendicular to the propagation
of the light beam. The direction of these fields is called the 'polarization direction'. Normal or
non-polarized light has fields in several directions; polarized light has a field in only one
direction.
Q: What differentiates passive matrix LCDs from active matrix LCDs?
file:///D|/My%20Documents/dfu/190G6/english/190g6/safety/saf_faq.htm (4 of 7)2005-08-23 1:19:08 PM
FAQs (Frequently Asked Questions)
A: An LCD is made with either a passive matrix or an active matrix display grid. An active
matrix has a transistor located at each pixel intersection, requiring less current to control
the luminance of a pixel. For this reason, the current in an active matrix display can be
switched on and off more frequently, improving the screen refresh time (your mouse pointer
will appear to move more smoothly across the screen, for example). The passive matrix LCD
has a grid of conductors with pixels located at each intersection in the grid.
Q: How does a TFT LCD Panel work?
A: On each column and row of the TFT LCD panel, a data source drive and a gate drive are
attached, respectively. The TFT drain of each cell is connected to the electrode. The
molecular arrangement of liquid crystal elements differ according to whether it is impressed
with voltage or not. It varies the direction of polarized light and the amount of light by letting
it through different arrays of liquid crystal elements. When two polarized filters are arranged
vertically on a polarized light pole, the light that passes through the upper polarized panel is
turned 90 degrees along with the spiral structure of the liquid crystal molecules and goes
through the polarized filter at the bottom. When impressed with voltage, liquid crystal
molecules are arranged vertically from the original spiral structure and the direction of the
light is not turned through 90 degrees. In this case, light that comes through the top
polarized panel may not go through the polarized panel at the bottom.
Q: What are the advantages of TFT LCD compared with CRT?
A: In a CRT monitor, a gun shoots electrons and general light by colliding polarized
electrons on fluorescent glass. Therefore, CRT monitors basically operate with an analog
RGB signal. A TFT LCD monitor is a device that displays an input image by operating a
liquid crystal panel. The TFT has a fundamentally different structure than a CRT: Each cell
has an active matrix structure and independent active elements. A TFT LCD has two glass
panels and the space between them is filled with liquid crystal. When each cell is connected
with electrodes and impressed with voltage, the molecular structure of the liquid crystal is
altered and controls the amount of inlet lighting to display images. A TFT LCD has several
advantages over a CRT, since it can be very thin and no flickering occurs because it does
not use the scanning method.
Q: Why is vertical frequency of 60Hz optimal for an LCD monitor?
A: Unlike a CRT monitor, the TFT LCD panel has a fixed resolution. For example, an XGA
monitor has 1024x3 (R, G, B) x 768 pixels and a higher resolution may not be available
without additional software processing. The panel is designed to optimize the display for a
65MHz dot clock, one of the standards for XGA displays. Since the vertical/horizontal
frequency for this dot clock is 60Hz/48kHz, the optimum frequency for this monitor is 60Hz.
Q: What kind of wide-angle technology is available? How does it work?
A: The TFT LCD panel is an element that controls/displays the inlet of a backlight using the
file:///D|/My%20Documents/dfu/190G6/english/190g6/safety/saf_faq.htm (5 of 7)2005-08-23 1:19:08 PM
FAQs (Frequently Asked Questions)
dual-refraction of a liquid crystal. Using the property that the projection of inlet light refracts
toward the major axis of the liquid element, it controls the direction of inlet light and
displays it. Since the refraction ratio of inlet light on liquid crystal varies with the inlet angle
of the light, the viewing angle of a TFT is much narrower than that of a CDT. Usually, the
viewing angle refers to the point where the contrast ration is 10. Many ways to widen the
viewing angle are currently being developed and the most common approach is to use a
wide viewing angle film, which widens the viewing angle by varying the refraction ratio. IPS
(In Plane Switching) or MVA (Multi Vertical Aligned) is also used to give a wider viewing
angle.
Q: Why is there no flicker on an LCD Monitor?
A: Technically speaking, LCDs do flicker, but the cause of the phenomenon is different from
that of a CRT monitor -- and it has no impact of the ease of viewing. Flickering in an LCD
monitor relates to usually undetectable luminance caused by the difference between
positive and negative voltage. On the other hand, CRT flickering that can irritate the human
eye occurs when the on/off action of the fluorescent object becomes visible. Since the
reaction speed of liquid crystal in an LCD panel is much slower, this troublesome form of
flickering is not present in an LCD display.
Q: Why is an LCD monitor virtually free of Electro Magnetic Interference?
A: Unlike a CRT, an LCD monitor does not have key parts that generate Electro Magnetic
Interference, especially magnetic fields. Also, since an LCD display utilizes relatively low
power, its power supply is extremely quiet.
RETURN TO TOP OF THE PAGE
Ergonomics, Ecology and Safety Standards
Q: What is the CE mark?
A: The CE (Conformité Européenne) mark is required to be displayed on all regulated
products offered for sale on the European market. This 'CE' mark means that a product
complies with the relevant European Directive. A European Directive is a European 'Law'
that relates to health, safety, environment and consumer protection, much the same as the U.
S. National Electrical Code and UL Standards.
More information is provided in the Regulatory Information section.
file:///D|/My%20Documents/dfu/190G6/english/190g6/safety/saf_faq.htm (6 of 7)2005-08-23 1:19:08 PM
FAQs (Frequently Asked Questions)
RETURN TO TOP OF THE PAGE
file:///D|/My%20Documents/dfu/190G6/english/190g6/safety/saf_faq.htm (7 of 7)2005-08-23 1:19:08 PM
Troubleshooting
Troubleshooting
• Safety and
Troubleshooting
• FAQs
• Common
Problems
• Imaging
Problems
• Regulatory
Information
• Other Related
Information
This page deals with problems that can be corrected by the user. If the problem still persists after
you have tried these solutions, contact your nearest Philips dealer.
Common Problems
Having this problem
Check these items
●
No Picture
(Power LED not lit)
●
●
●
No Picture
●
(Power LED is amber or yellow)
●
Screen says
●
●
●
●
AUTO button not working properly
●
●
Imaging Problems
file:///D|/My%20Documents/dfu/190G6/english/190g6/safety/saf_troub.htm (1 of 3)2005-08-23 1:19:09 PM
Make sure the power cord is plugged into
the power outlet and into the back of the
monitor.
First, ensure that the power button on the
front of the monitor is in the OFF position,
then press it to the ON position.
Make sure the computer is turned on.
Make sure the signal cable is properly
connected to your computer.
Check to see if the monitor cable has bent
pins.
The Energy Saving feature may be
activated
Make sure the monitor cable is properly
connected to your computer. (Also refer to
the Quick Set-Up Guide).
Check to see if the monitor cable has bent
pins.
Make sure the computer is turned on.
The Auto Function is designed for use on
standard Macintosh or IBM-compatible
PCs running Microsoft Windows.
It may not work properly if using
nonstandard PC or video card.
The AUTO adjustment does not function
when digital input is used for display.
Troubleshooting
●
●
Display position is incorrect
●
Image vibrates on the screen
Press the Auto button.
Adjust the image position using the
Horizontal Position and/or Vertical Position
in OSD Main Controls.
Check that the signal cable is properly
connected to the graphics board or PC.
Vertical flicker appears
●
●
Press the Auto button.
Eliminate the vertical bars using the Phase/
Clock of More Settings in OSD Main
Controls.
Horizontal flicker appears
●
●
●
The screen is too bright or too dark
●
An after-image appears
●
An after-image remains after the
power has been turned off.
file:///D|/My%20Documents/dfu/190G6/english/190g6/safety/saf_troub.htm (2 of 3)2005-08-23 1:19:09 PM
Press the Auto button.
Eliminate the vertical bars using the Phase/
Clock of More Settings in OSD Main
Controls.
Adjust the contrast and brightness on OSD
Main Controls. (The backlight of the LCD
monitor has a fixed life span. When the
screen becomes dark or begins to flicker,
please contact your dealer).
If an image remains on the screen for an
extended period of time, it may be
imprinted in the screen and leave an afterimage. This usually disappears after a few
hours
This is characteristic of liquid crystal and is
not caused by a malfunction or
deterioration of the liquid crystal. The afterimage will disappear after a peroid of time.
Troubleshooting
●
Green, red, blue, dark, and white dots
remains
The remaining dots are normal
characteristic of the liquid crystal used in
today’s technology.
For further assistance, refer to the Consumer Information Centers list and contact your local
Philips distributor.
RETURN TO TOP OF THE PAGE
file:///D|/My%20Documents/dfu/190G6/english/190g6/safety/saf_troub.htm (3 of 3)2005-08-23 1:19:09 PM
Regulatory Information
CE Declaration
of Conformity
Energy Star
•
Declaration
•Federal
Communications
Commission
(FCC) Notice (U.
S. Only)
•Commission
Federale de la
Communication
(FCC
Declaration)
•EN 55022
Compliance
(Czech Republic
Only)
•VCCI Class 2
Notice (Japan
Only)
•MIC Notice
(South Korea
Only)
•Polish Center
for Testing and
Certification
Notice
•North Europe
(Nordic
Countries)
Information
•BSMI Notice
(Taiwan Only)
•Ergonomie
Hinweis (nur
Deutschland)
•Philips End-ofLife Disposal
Information for
•
UK only
Waste Electrical
and Electronic
•
EquipmentWEEE
•Troubleshooting
Other Related
•
Information
•
Regulatory Information
CE Declaration of Conformity
Philips Consumer Electronics declare under our responsibility that the product is in conformity with
the following standards
- EN60950-1:2001 (Safety requirement of Information Technology Equipment)
- EN55022:1998 (Radio Disturbance requirement of Information Technology Equipment)
- EN55024:1998 (Immunity requirement of Information Technology Equipment)
- EN61000-3-2:2000 (Limits for Harmonic Current Emission)
- EN61000-3-3:1995 (Limitation of Voltage Fluctuation and Flicker)
following provisions of directives applicable
- 73/23/EEC (Low Voltage Directive)
- 89/336/EEC (EMC Directive)
- 93/68/EEC (Amendment of EMC and Low Voltage Directive)
and is produced by a manufacturing organization on ISO9000 level.
The product also comply with the following standards
- ISO9241-3, ISO9241-7, ISO9241-8 (Ergonomic requirement for Visual Display)
- ISO13406-2 (Ergonomic requirement for Flat panels)
- GS EK1-2000 (GS specification)
- prEN50279:1998 (Low Frequency Electric and Magnetic fields for Visual Display)
- MPR-II (MPR:1990:8/1990:10 Low Frequency Electric and Magnetic fields)
- TCO'99, TCO'03 (Requirement for Environment Labelling of Ergonomics, Energy, Ecology and
Emission, TCO: Swedish Confederation of Professional Employees) for TCO versions
RETURN TO TOP OF THE PAGE
Energy Star Declaration
PHILIPS
190G6
This monitor is equipped with a function for saving energy which supports the VESA Display
Power Management Signaling (DPMS) standard. This means that the monitor must be
connected to a computer which supports VESA DPMS to fulfill the requirements in the NUTEK
specification 803299/94. Time settings are adjusted from the system unit by software.
NUTEK
VESA State
LED Indicator
Power Consumption
Normal operation
ON (Active)
Green
< 62 W (without subwoofer)
file:///D|/My%20Documents/dfu/190G6/english/190g6/safety/regs/regulat.htm (1 of 9)2005-08-23 1:19:10 PM
Regulatory Information
•Frequently
Asked
Questions
(FAQs)
Power Saving
Alternative 2
One step
OFF (Sleep)
Amber
<2W
Switch Off
Off
<1W
As an ENERGY STAR® Partner, PHILIPS has determined that this product
meets the ENERGY STAR® guidelines for energy efficiency.
We recommend you switch off the monitor when it is not in use for quite a long time.
RETURN TO TOP OF THE PAGE
Federal Communications Commission (FCC) Notice (U.S. Only)
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
●
●
●
●
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
Use only RF shielded cable that was supplied with the monitor when connecting this monitor to a
computer device.
To prevent damage which may result in fire or shock hazard, do not expose this appliance to rain or
excessive moisture.
THIS CLASS B DIGITAL APPARATUS MEETS ALL REQUIREMENTS OF THE CANADIAN
INTERFERENCE-CAUSING EQUIPMENT REGULATIONS.
file:///D|/My%20Documents/dfu/190G6/english/190g6/safety/regs/regulat.htm (2 of 9)2005-08-23 1:19:10 PM
Regulatory Information
RETURN TO TOP OF THE PAGE
Commission Federale de la Communication (FCC Declaration)
Cet équipement a été testé et déclaré conforme auxlimites des appareils numériques
de class B,aux termes de l'article 15 Des règles de la FCC. Ces limites sont conçues
de façon à fourir une protection raisonnable contre les interférences nuisibles dans le
cadre d'une installation résidentielle. CET appareil produit, utilise et peut émettre des
hyperfréquences qui, si l'appareil n'est pas installé et utilisé selon les consignes
données, peuvent causer des interférences nuisibles aux communications radio.
Cependant, rien ne peut garantir l'absence d'interférences dans le cadre d'une
installation particulière. Si cet appareil est la cause d'interférences nuisibles pour la
réception des signaux de radio ou de télévision, ce qui peut être décelé en fermant
l'équipement, puis en le remettant en fonction, l'utilisateur pourrait essayer de
corriger la situation en prenant les mesures suivantes:
●
●
●
●
Réorienter ou déplacer l'antenne de réception.
Augmenter la distance entre l'équipement et le récepteur.
Brancher l'équipement sur un autre circuit que celui utilisé par le récepteur.
Demander l'aide du marchand ou d'un technicien chevronné en radio/télévision.
Toutes modifications n'ayant pas reçu l'approbation des services compétents en
matière de conformité est susceptible d'interdire à l'utilisateur l'usage du présent
équipement.
N'utiliser que des câbles RF armés pour les connections avec des ordinateurs ou périphériques.
CET APPAREIL NUMERIQUE DE LA CLASSE B RESPECTE TOUTES LES EXIGENCES DU
REGLEMENT SUR LE MATERIEL BROUILLEUR DU CANADA.
RETURN TO TOP OF THE PAGE
EN 55022 Compliance (Czech Republic Only)
RETURN TO TOP OF THE PAGE
file:///D|/My%20Documents/dfu/190G6/english/190g6/safety/regs/regulat.htm (3 of 9)2005-08-23 1:19:10 PM
Regulatory Information
VCCI Notice (Japan Only)
This is a Class B product based on the standard of the Voluntary Control Council for Interference
(VCCI) for Information technology equipment. If this equipment is used near a radio or television
receiver in a domestic environment, it may cause radio Interference. Install and use the equipment
according to the instruction manual.
Class B ITE
RETURN TO TOP OF THE PAGE
MIC Notice (South Korea Only)
Class B Device
Please note that this device has been approved for non-business purposes and may be used in any
environment, including residential areas.
RETURN TO TOP OF THE PAGE
Polish Center for Testing and Certification Notice
The equipment should draw power from a socket with an attached protection circuit (a three-prong
socket). All equipment that works together (computer, monitor, printer, and so on) should have the
file:///D|/My%20Documents/dfu/190G6/english/190g6/safety/regs/regulat.htm (4 of 9)2005-08-23 1:19:10 PM
Regulatory Information
same power supply source.
The phasing conductor of the room's electrical installation should have a reserve short-circuit
protection device in the form of a fuse with a nominal value no larger than 16 amperes (A).
To completely switch off the equipment, the power supply cable must be removed from the power
supply socket, which should be located near the equipment and easily accessible.
A protection mark "B" confirms that the equipment is in compliance with the protection usage
requirements of standards PN-93/T-42107 and PN-89/E-06251.
RETURN TO TOP OF THE PAGE
North Europe (Nordic Countries) Information
Placering/Ventilation
VARNING:
FÖRSÄKRA DIG OM ATT HUVUDBRYTARE OCH UTTAG ÄR LÄTÅTKOMLIGA, NÄR
DU STÄLLER DIN UTRUSTNING PÅPLATS.
file:///D|/My%20Documents/dfu/190G6/english/190g6/safety/regs/regulat.htm (5 of 9)2005-08-23 1:19:10 PM
Regulatory Information
Placering/Ventilation
ADVARSEL:
SØRG VED PLACERINGEN FOR, AT NETLEDNINGENS STIK OG STIKKONTAKT
ER NEMT TILGÆNGELIGE.
Paikka/Ilmankierto
VAROITUS:
SIJOITA LAITE SITEN, ETTÄ VERKKOJOHTO VOIDAAN TARVITTAESSA HELPOSTI
IRROTTAA PISTORASIASTA.
Plassering/Ventilasjon
ADVARSEL:
NÅR DETTE UTSTYRET PLASSERES, MÅ DU PASSE PÅ AT KONTAKTENE FOR
STØMTILFØRSEL ER LETTE Å NÅ.
RETURN TO TOP OF THE PAGE
BSMI Notice (Taiwan Only)
RETURN TO TOP OF THE PAGE
Ergonomie Hinweis (nur Deutschland)
Der von uns gelieferte Farbmonitor entspricht den in der "Verordnung über den Schutz vor Schäden
durch Röntgenstrahlen" festgelegten Vorschriften.
Auf der Rückwand des Gerätes befindet sich ein Aufkleber, der auf die Unbedenklichkeit der
Inbetriebnahme hinweist, da die Vorschriften über die Bauart von Störstrahlern nach Anlage III ¤ 5
Abs. 4 der Röntgenverordnung erfüllt sind.
file:///D|/My%20Documents/dfu/190G6/english/190g6/safety/regs/regulat.htm (6 of 9)2005-08-23 1:19:10 PM
Regulatory Information
Damit Ihr Monitor immer den in der Zulassung geforderten Werten entspricht, ist darauf zu achten,
daß
1. Reparaturen nur durch Fachpersonal durchgeführt werden.
2. nur original-Ersatzteile verwendet werden.
3. bei Ersatz der Bildröhre nur eine bauartgleiche eingebaut wird.
Aus ergonomischen Gründen wird empfohlen, die Grundfarben Blau und Rot nicht auf dunklem
Untergrund zu verwenden (schlechte Lesbarkeit und erhöhte Augenbelastung bei zu geringem
Zeichenkontrast wären die Folge).
Der arbeitsplatzbezogene Schalldruckpegel nach DIN 45 635 beträgt 70dB (A) oder weniger.
ACHTUNG: BEIM AUFSTELLEN DIESES GERÄTES DARAUF ACHTEN, DAß
NETZSTECKER UND NETZKABELANSCHLUß LEICHT ZUGÄNGLICH SIND.
RETURN TO TOP OF THE PAGE
End-of-Life Disposal
Your new monitor contains materials that can be recycled and reused. Specialized companies can
recycle your product to increase the amount of reusable materials and to minimize the amount to be
disposed of.
Please find out about the local regulations on how to dispose of your old monitor from your local
Philips dealer.
(For customers in Canada and U.S.A.)
This product may contain lead and/or mercury. Dispose of in accordance to local-state and federal
regulations.
For additional information on recycling contact www.eia.org (Consumer Education Initiative)
RETURN TO TOP OF THE PAGE
Information for UK only
file:///D|/My%20Documents/dfu/190G6/english/190g6/safety/regs/regulat.htm (7 of 9)2005-08-23 1:19:10 PM
Regulatory Information
WARNING - THIS APPLIANCE MUST BE
EARTHED.
Important:
This apparatus is supplied with an approved
moulded 13A plug. To change a fuse in this type
of plug proceed as follows:
1. Remove fuse cover and fuse.
2. Fit new fuse which should be a BS 1362 5A,A.
S.T.A. or BSI approved type.
3. Refit the fuse cover.
If the fitted plug is not suitable for your socket
outlets, it should be cut off and an appropriate 3pin plug fitted in its place.
If the mains plug contains a fuse, this should
have a value of 5A. If a plug without a fuse is
used, the fuse at the distribution board should
not be greater than 5A.
Note: The severed plug must be destroyed to
avoid a possible shock hazard should it be
inserted into a 13A socket elsewhere.
How to connect a plug
The wires in the mains lead are coloured in
accordance with the following code:
BLUE - "NEUTRAL" ("N")
BROWN - "LIVE" ("L")
GREEN & YELLOW - "EARTH" ("E")
1. The GREEN AND YELLOW wire must be
connected to the terminal in the plug which is
marked with the letter "E" or by the Earth symbol
or coloured GREEN or GREEN AND
YELLOW.
2. The BLUE wire must be connected to the
terminal which is marked with the letter "N" or
coloured BLACK.
file:///D|/My%20Documents/dfu/190G6/english/190g6/safety/regs/regulat.htm (8 of 9)2005-08-23 1:19:10 PM
Regulatory Information
3. The BROWN wire must be connected to the
terminal which marked with the letter "L" or
coloured RED.
Before replacing the plug cover, make certain
that the cord grip is clamped over the sheath of
the lead - not simply over the three wires.
RETURN TO TOP OF THE PAGE
Waste Electrical and Electronic Equipment-WEEE
Attention users in European Union private households
This marking on the product or on its packaging illustrates that, under European
Directive 2002/96/EG governing used electrical and electronic appliances, this product may not be
disposed of with normal household waste. You are responsible for disposal of this equipment
through a designated waste electrical and electronic equipment collection. To determine the
locations for dropping off such waste electrical and electronic, contact your local government office,
the waste disposal organization that serves your household or the store at which you purchased the
product.
RETURN TO TOP OF THE PAGE
file:///D|/My%20Documents/dfu/190G6/english/190g6/safety/regs/regulat.htm (9 of 9)2005-08-23 1:19:10 PM
Other Related Information
• Safety and
Troubleshooting
• FAQs
Other Related Information
• Troubleshooting Information for Users in the U. S.
• Regulatory
Information
• Information
for Users in the
U.S
• Information
for Users
Outside the U.S
For units set at 115 V :
Use a UL Listed Cord Set consisting of a minimum 18 AWG, Type SVT or SJT three conductor cord
a maximum of 15-feet long and a parallel blade, grounding type attachment plug rated 15 A, 125 V.
For units set at 230 V:
Use a UL Listed Cord Set consisting of a minimum 18 AWG, Type SVT or SJT three conductor cord
a maximum of 15-feet long and a tandem blade, grounding type attachment plug rated 15 A, 250 V.
Information for Users outside the U.S.
For units set at 230 V:
Use a Cord Set consisting of a minimum 18 AWG cord and grounding type attachment plug rated
15 A, 250 V. The Cord Set should have the appropriate safety approvals for the country in which
the equipment will be installed and / or be marked HAR.
RETURN TO TOP OF THE PAGE
file:///D|/My%20Documents/dfu/190G6/english/190g6/safety/saf_other.htm2005-08-23 1:19:10 PM
Connecting to Your PC
Connecting to Your PC
• Front View
Product
Accessory Pack
Description
• Accessory
Unpack all the parts
Pack
• Connecting
to Your PC
• Connect for
AV
functionality
(Europe
only)
• Connect for
TV
Power Cord
Functionality
(Monitor)
(Asia
Pacificonly)
• Getting
Started
• Optimizing
Performance
Power Cord
(Subwoofer)
D-Sub
DVI-D
USB cable
Component (YPbPr)
Subwoofer Cable
Subwoofer Audio
EDFU pack
Remote Control
(Not availabe for all model)
RETURN TO TOP OF THE PAGE
file:///D|/My%20Documents/dfu/190G6/english/190g6/install/connect.htm (1 of 12)2005-08-23 1:19:24 PM
Connecting to Your PC
Connecting to Your PC
1)
Remove backcover from vertical monitor.
2)Cable management
3)
If you use an Apple Macintosh, you need to connect the special Mac adapter to one
end of the monitor signal cable.
file:///D|/My%20Documents/dfu/190G6/english/190g6/install/connect.htm (2 of 12)2005-08-23 1:19:24 PM
Connecting to Your PC
4)Connect to PC
(1)
Turn off your computer and unplug its power cable.
(2)
Connect the monitor signal cable to the video connector on the back of your computer.
(3)
Plug the power cord of your computer and your monitor into a nearby outlet.
(4)
USB plug
(a) Connect USB upstream port on monitor and the USB port on PC with a USB cable.
(b) The USB downstream port is now ready for any USB device to plug in
(5)
Turn on your computer and monitor. If the monitor displays an image, installation is
complete.
Note: The USB plug is a pass through connection whether it can support USB 1.1 or USB 2.0
depends on your PC's specification.
5)Connect for AV functionality (Europe Only)
SCART Connentions
This connection will supply stereo sound to the display.
file:///D|/My%20Documents/dfu/190G6/english/190g6/install/connect.htm (3 of 12)2005-08-23 1:19:24 PM
Connecting to Your PC
Using a scart cable (not supplied) connect one end of the scart cable to the scart jocket of the
(1) scart enabled device. Connect the other end of the scart cable to the scart jack on the bottom
of the display.
(2)
Plug the DC adapter into the DC IN 16V jack on the display.
Plug the power cable into an outlet and switch the display set on.
S-Video Connections
The S-Video connection on the rear of the display can provide you with better picture detail and
clarity for the playback of accessory sources such as DBS (digital broadcast satellite), DVD (digital
video discs), video games, and VHS VCR (video cassette recorder) tapes than the normal antenna
picture connections.
file:///D|/My%20Documents/dfu/190G6/english/190g6/install/connect.htm (4 of 12)2005-08-23 1:19:24 PM
Connecting to Your PC
(1) Connect an S-Video cable to the S-VIDEO jack of the other equipment (DVD Player,
Camcorder, etc.) and to the S-VIDEO jack on the rear of the display.
(2) Connect RCA-style audio cables (usually red and white) to the AUDIO OUT (left and right)
jacks on the other equipment. Connect the other end of the cables to the AUDIO jack on the
side of the display.
(3) Plug the DC Adapter into the DC IN 16V jack on the display. Plug the power cable into an
outlet. Turn on the display and other equipment.
(4) Press the OSD buttons until S-Video appears on the screen.
(5) Press PLAY on the other equipment to view its material on the display.
Component (HD) Connections
Component Video input provide the highest possible color and picture resolution in the playback of
digital signal source material, such as with DVD players. If you are using a HD (High Definition)
receiver that can transmit high definition programming, the display can accept those signals through
the Component input located on the
bottom of the display.
file:///D|/My%20Documents/dfu/190G6/english/190g6/install/connect.htm (5 of 12)2005-08-23 1:19:24 PM
Connecting to Your PC
(1) Connect the component (Y, Pb, Pr) Video OUT jacks from the DVD player (or similar device)
to the COMP(onent) VIDEO Input jacks on the bottom of the display.
(2) Connect the red and white AUDIO CABLES to the Audio (left and right) output jacks on the
rear of the accessory device to the AUDIO IN jack. Connect the other end of the cable to the
Audio jack on the rear of display.
(3) Plug the DC Adapter into the DC IN 16 V jack on the display. Plug the power cable into an
outlet. Turn on the display and other equipment.
(4) Press the OSD button until HD appears on the screen.
(5) Insert a DVD disc into the DVD player and press the PLAY button on the DVD Player.
PC (Monitor) Inputs
This display can be used as a PC monitor. Your computer will have to be equipped with a VGA type
video output and interface cable (supplied).
file:///D|/My%20Documents/dfu/190G6/english/190g6/install/connect.htm (6 of 12)2005-08-23 1:19:24 PM
Connecting to Your PC
(1) Connect the VGA/DVI or DVI end of the interface cable to the computer, while connecting the
other end to the D-SUB or DVI INPUT jack on the display.
(2) Although audio connections are not required, the display can reproduce the computers audio
out by an AUDIO ADAPTER to the Audio output jack on the computer (if available) while
connecting the other end of the Audio cables to the PC AUDIO Jacks on the bottom of the
display.
(3) Plug the DC Adapter into the DC IN 16V jack on the display. Plug the power cable into an
outlet. Turn on the display and PC.
(4) Press the OSD button until PC MODE appears on the screen.
6) Connect for AV/TV functionality (Asia Pacific Only)
Cable Box (with RF in/outputs)
file:///D|/My%20Documents/dfu/190G6/english/190g6/install/connect.htm (7 of 12)2005-08-23 1:19:24 PM
Connecting to Your PC
(1)
Connect the Cable TV signal to the IN jack (or RF IN or CABLE IN) on the Cable Box.
(2)
Connect an RF coaxial cable (not supplied) to the OUT jack (or TO TV or RF OUT) of the
Cable Box.
(3)
Connect the other end of the coaxial cable to one end of the supplied L-Adapter as shown,
and connect the other end of the adapter to the TV jack on the LCD TV.
(4)
Plug the DC adapter into the DC IN 16V jack on the LCD TV. Plug the power cable into an
outlet and switch TV set on.
(5)
Set the Channel 3/4 (or Output channel) switch of the Cable Box to 3 or 4. Set the TV to
the same channel. When watching TV programming, change channels at the Cable Box,
not the LCD TV.
●
Helpful
Hint
●
Immediately after unpacking and plugging in your new television, run the auto
program function to set up the TV for the broadcast or cable channels available in
your area. If you do not run the auto program function to set up the channels , your
television may not
operate properly.
Please make sure that you have selected the TV mode with AV+ key
on your remote control, before installing TV channels.
Cable Box (with Audio/Video outputs)
This connection will supply stereo sound to the LCD TV.
file:///D|/My%20Documents/dfu/190G6/english/190g6/install/connect.htm (8 of 12)2005-08-23 1:19:24 PM
Connecting to Your PC
(1) Connect the Cable TV signal to the IN jack (or RF IN or CABLE IN) on the Cable Box.
(2) Using an RCA-type video cable (not supplied) connect one end of the video cable to the
Video Out jack of the Cable Box. Connect the other end of the cable to the yellow VIDEO jack
on the side of the TV. Video cables are usually marked with yellow and are available from
Philips or electronics retailers. Video jacks on most
equipment are yellow.
(3) Using RCA-type, stereo audio cables (not supplied), connect one end of the cables to the left
and right Audio Out jacks of the Cable Box. Connect the other end of that cable to the Audio
jack on the side of the LCD TV. Audio cables are usually marked with red and white and are
available from Philips or electronics retailers. The right audio jack is red and the left audio
jack is white. Match the cable colors to the jack colors.
(4) Plug the DC adapter into the DC IN 16V jack on the LCD TV. Plug the power cable into an
outlet and switch TV set on.
Use the AV+ button on the remote control to tune to the AV channel for the cable box
signal. Once tuned, change channels at the cable box, not the television. When you watch
programs using VCR, it’s recommended to select Soft Mode via Smart picture.
S-Video Connections
The S-Video connection on the rear of the LCD TV can provide you with better picture detail and
clarity for the playback of accessory sources such as DBS (digital broadcast satellite), DVD (digital
video discs), video games, and VHS VCR (video cassette recorder) tapes than the normal antenna
picture connections.
file:///D|/My%20Documents/dfu/190G6/english/190g6/install/connect.htm (9 of 12)2005-08-23 1:19:24 PM
Connecting to Your PC
(1) Connect an S-Video cable to the S-VIDEO jack of the other equipment (DVD Player,
Camcorder, etc.) and to the S-VIDEO jack on the rear of the LCD TV.
(2) Connect RCA-style audio cables (usually red and white) to the AUDIO OUT (left and right)
jacks on the other equipment. Connect the other end of the cables to the AUDIO jack on the
side of the LCD TV.
(3) Plug the DC Adapter into the DC IN 16V jack on the LCD TV. Plug the power cable into an
outlet. Turn on the LCD TV and other equipment.
(4) Press the AV buttons to set the LCD TV to its S-VIDEO mode.
(5) Press PLAY on the other equipment to view its material on the LCD TV.
The Philips LCD TV remote control can not be used to operate other video/audio
equipment.
The Audio jack of AV IN is shared between Video (CVBS) and S-Video signals. If Audio
and Video is connected to S-Video input, you can still hear sound if you select Video via
AV select, even there appears no image on screen.
Component (HD) Connections
Component Video input provide the highest possible color and picture resolution in the playback of
digital signal source material, such as with DVD players. If you are using a HD (High Definition)
receiver that can transmit high definition programming, the TV can accept those signals through the
Component input located on the bottom of the TV.
file:///D|/My%20Documents/dfu/190G6/english/190g6/install/connect.htm (10 of 12)2005-08-23 1:19:24 PM
Connecting to Your PC
(1) Connect the component (Y, Pb, Pr) Video OUT jacks from the DVD player (or similar device)
to the COMP(onent) VIDEO Input jacks on the bottom of the LCD TV.
(2) Connect the red and white AUDIO CABLES to the Audio (left and right) output jacks on the
rear of the accessory device to the AUDIO IN jack. Connect the other end of the cable to the
Audio jack on the rear of LCD TV.
(3) Plug the DC Adapter into the DC IN 16 V jack on the LCD TV. Plug the power cable into an
outlet. Turn on the LCD TV and other equipment.
(4) Press the AV button on the remote control to select HD. HD will appear in the upper left
corner on the TV screen.
(5) Insert a DVD disc into the DVD player and press the PLAY button on the DVD Player.
The Philips LCD TV remote control can not be used to operate other video/audio
equipment.
PC (Monitor) inputs
This LCD TV can be used as a PC display monitor. Your computer will have to be equipped with a
VGA type video output and interface cable (supplied).
file:///D|/My%20Documents/dfu/190G6/english/190g6/install/connect.htm (11 of 12)2005-08-23 1:19:24 PM
Connecting to Your PC
(1) Connect the VGA or DVI end of the interface cable (supplied) to the computer, while
connecting the other end to the DSUB or DVI INPUT jack on the LCD TV.
(2) Although audio connections are not required, the LCD TV can reproduce the computers audio
out by an AUDIO ADAPTER to the Audio output jack on the computer (if available) while
connecting the other ends of the Audio cables to the PC AUDIO Jacks on the bottom of the
TV.
(3) Plug the DC Adapter into the DC IN 16V jack on the LCD TV. Plug the power cable into an
outlet. Turn on the LCD TV and PC.
(4) Press the AV button until PC MODE appears on the screen.
USB digital audio applicable in PC mode only.
RETURN TO TOP OF THE PAGE
file:///D|/My%20Documents/dfu/190G6/english/190g6/install/connect.htm (12 of 12)2005-08-23 1:19:24 PM
Getting Started
Your LCD
Monitor :
• Front View
Product
Description
• Connecting
to Your PC
• Getting
Started
• Optimizing
Performance
Getting Started
Getting Started
Philips Sound Agent2™ software is only compatible with Windows® 2000/XP.
Please read the PSA2 user guide for further details.
Use the information file ( .inf) for Windows® 95/98/2000/Me/XP or later
The built-in VESA DDC2B feature in Philips Monitors supports Plug & Play requirements for
Windows® 95/98/2000/Me/XP. This information file ( .inf) should be installed in order that your
Philips monitor can be enabled from the 'Monitor' dialog box in Windows® 95/98/2000/Me/XP
and the Plug & Play application can be activated. The installation procedure based on
Windows® '95 OEM Release 2 , 98 , Me, XP and 2000 is specified as follows.
For Windows® 95
1.
2.
3.
4.
5.
6.
Start Windows® '95.
Click on the 'Start' button, point to 'Settings', and then click on 'Control Panel'.
Double click on the 'Display' icon.
Select the 'Settings' tab then click on 'Advanced...'.
Select the 'Monitor' button, point to 'Change...' then click on 'Have Disk...'.
Click on the 'Browse...' button, select the appropriate drive F: ( CD-ROM Drive) then click
on the 'OK' button.
7. Click on the 'OK' button then select your monitor model and click on 'OK'.
8. Click on the 'Close' button.
For Windows® 98
1.
2.
3.
4.
5.
6.
Start Windows® 98.
Click on the 'Start' button, point to 'Settings', and then click on 'Control Panel'.
Double click on the 'Display' icon.
Select the 'Settings' tab then click on 'Advanced...'.
Select the 'Monitor' button, point to 'Change...' then click on 'Next'
Select 'Display a list of all the drivers in a specific location, so you can choose the driver
you want.' then click on 'Next' and then click on 'Have Disk...'.
7. Click on the 'Browse...' button, select the appropriate drive F: ( CD-ROM Drive) then click
on the 'OK' button.
8. Click on the 'OK' button then select your monitor model and click on the 'Next' button.
9. Click on the 'Finish' button then the 'Close' button.
For Windows® Me
file:///D|/My%20Documents/dfu/190G6/english/190g6/install/gt_start.htm (1 of 3)2005-08-23 1:19:24 PM
Getting Started
1.
2.
3.
4.
5.
6.
7.
Start Windows® Me.
Click on the 'Start' button, point to 'Settings', and then click on 'Control Panel'.
Double click on the 'Display' icon.
Select the 'Settings' tab then click on 'Advanced...'.
Select the 'Monitor' button, then click on 'Change...' button.
Select 'Specify the location of the driver(Advanced)' and click on the 'Next' button.
Select 'Display a list of all the drivers in a specific location, so you can choose the driver
you want', then click on 'Next' and then click on 'Have Disk...'.
8. Click on the 'Browse...' button, select the appropriate drive F: ( CD-ROM Drive) then click
on the 'OK' button.
9. Click on the 'OK' button, select your monitor model and click on the 'Next' button.
10. Click on 'Finish' button then the 'Close' button.
For Windows® 2000
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
Start Windows® 2000.
Click on the 'Start' button, point to 'Settings', and then click on 'Control Panel'.
Double click on the 'Display' icon.
Select the 'Settings' tab then click on 'Advanced...'.
Select 'Monitor'
- If the 'Properties' button is inactive, it means your monitor is properly configured. Please
stop installation.
- If the 'Properties' button is active. Click on 'Properties' button. Please follow the steps
given below.
Click on 'Driver' and then click on 'Update Driver...' then click on the 'Next' button.
Select 'Display a list of the known drivers for this device so that I can choose a specific
driver', then click on 'Next' and then click on 'Have disk...'.
Click on the 'Browse...' button then select the appropriate drive F: ( CD-ROM Drive).
Click on the 'Open' button, then click on the 'OK' button.
Select your monitor model and click on the 'Next' button.
Click on the 'Finish' button then the 'Close' button.
If you can see the 'Digital Signature Not Found' window, click on the 'Yes' button.
For Windows® XP
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
Start Windows® XP.
Click on the 'Start' button and then click on 'Control Panel'.
Select and click on the category 'Printers and Other Hardware'
Click on the 'Display' Item.
Select the 'Settings' tab then click on the 'Advanced' button.
Select 'Monitor' tab
- If the 'Properties' button is inactive, it means your monitor is properly configured. Please
stop installation.
- If the 'Properties' button is active, click on 'Properties' button.
Please follow the steps below.
Click on the 'Driver' tab and then click on 'Update Driver...' button.
Select the 'Install from a list or specific location [advanced]' radio button and then click on
the 'Next' button.
Select the 'Don't Search. I will choose the driver to install' radio button. Then click on the
'Next' button.
Click on the 'Have disk...' button, then click on the 'Browse...' button and then select the
appropriate drive F: (CD-ROM Drive).
Click on the 'Open' button, then click the 'OK' button.
file:///D|/My%20Documents/dfu/190G6/english/190g6/install/gt_start.htm (2 of 3)2005-08-23 1:19:24 PM
Getting Started
12. Select your monitor model and click on the 'Next' button.
- If you can see the 'has not passed Windows® Logo testing to verify its compatibility with
Windows® XP' message, please click on the 'Continue Anyway' button.
13. Click on the 'Finish' button then the 'Close' button.
14. Click on the 'OK' button and then the 'OK' button again to close the Display_Properties
dialog box.
If your Windows® 95/98/2000/Me/XP version is different or you need more detailed installation
information, please refer to Windows® 95/98/2000/Me/XP user's manual.
RETURN TO TOP OF THE PAGE
file:///D|/My%20Documents/dfu/190G6/english/190g6/install/gt_start.htm (3 of 3)2005-08-23 1:19:24 PM
Your Philips F1rst Choice Warranty
Your Philips F1rst Choice Warranty
Thank you for purchasing this Philips monitor.
All Philips monitors are designed and manufactured to high standards and deliver
high-quality performance, ease of use and ease of installation. Should you
encounter any difficulties while installing or using this product, please contact the
Philips helpdesk directly to benefit from your Philips F1rst Choice Warranty. This
three-year service warranty entitles you to a swap model on-site if your monitor
turns out to be faulty or defective. Philips aims at a swap within 48 hours of your
call being received.
What is covered?
The Philips F1rst Choice Warranty applies within Andorra, Austria, Belgium, Cyprus, Denmark,
France, Germany, Greece, Finland, Ireland, Italy, Liechtenstein, Luxembourg, Monaco, the
Netherlands, Norway, Portugal, Sweden, Switzerland, Spain and the United Kingdom and only for
monitors originally designed, manufactured, approved and/or authorized for usage within these
countries.
Warranty coverage begins as from the day you buy your monitor. For three years thereafter, your
monitor will be swapped by at least an equivalent monitor in case of defects provided for under the
warranty coverage.
The swap monitor remains yours and Philips keeps the defective/original monitor. For the swap
monitor the warranty period remains equal to that of your original monitor, being 36 months as from
the purchase date of your original monitor.
What is excluded?
The Philips F1rst Choice Warranty applies provided the product is handled properly for its intended
use, in accordance with its operating instructions and upon presentation of the original invoice or
cash receipt, indicating the date of purchase, dealer's name and model and production number of
the product.
The Philips F1rst Choice Warranty may not apply if:
●
●
●
●
The documents have been altered in any way or made illegible;
The model or production number on the product has been altered, deleted, removed or
made illegible;
Repairs or product modifications and alterations have been executed by unauthorized
service organizations or persons;
Damage is caused by accidents including but not limited to lightning, water or fire, misuse or
neglect;
file:///D|/My%20Documents/dfu/190G6/english/warranty/war_1st.htm (1 of 3)2005-08-23 1:19:31 PM
Your Philips F1rst Choice Warranty
●
●
●
●
Reception problems caused by signal conditions or cable or antenna systems outside the
unit;
Defects caused by abuse or misuse of the monitor;
Product requires modification or adaptation to enable it to comply with local or national
technical standards, which apply in countries for which the product was not originally
designed, manufactured, approved and/or authorized. Therefore always check whether a
product can be used in a specific country.
Note that products that are not originally designed, manufactured, approved and/or
authorized for usage within the Philips F1rst Choice countries, do not apply to the Philips
F1rst Choice Warranty. In these cases the Philips global warranty terms are valid.
Just a click away
In case of any problems, we advise you to read the operating instructions carefully or go to the www.
philips.com/support website for additional support.
Just a phone call away
In order to avoid unnecessary inconvenience, we advise you to read the operating instructions
carefully or go to the www.philips.com/support website for additional support before contacting the
Philips helpdesk.
To solve your problem quickly, please prepare the following details before contacting the Philips
helpdesk:
●
●
●
●
●
Philips type number
Philips serial number
Purchase date (copy of purchase may be required)
PC environment Processor:
❍ 286/386/486/Pentium Pro/Internal memory
❍ Operating system (Windows, DOS, OS/2, MAC)
❍ Fax/Modem/Internet program?
Other cards installed
Having the following information available will also help speed up the process:
●
●
Your proof of purchase indicating: date of purchase, dealer name, model and product serial
number.
The full address to which the faulty monitor has to be collected and the swap model should
be delivered.
Philips' customer help desks are located worldwide. Click here to access the F1rst Choice Contact
Information.
Or you can reach us via:
Website: http://www.philips.com/support
file:///D|/My%20Documents/dfu/190G6/english/warranty/war_1st.htm (2 of 3)2005-08-23 1:19:31 PM
Your Philips F1rst Choice Warranty
file:///D|/My%20Documents/dfu/190G6/english/warranty/war_1st.htm (3 of 3)2005-08-23 1:19:31 PM
Your Guarantee in Central and Eastern Europe
Your Guarantee in Central and Eastern Europe
Dear Customer,
Thank you for purchasing this Philips product, which has been designed and manufactured to the
highest quality standards. If, unfortunately, something should go wrong with this product Philips
guarantees free of charge labor and replacement parts during a period of 36 months from date of
purchase.
What is covered?
This Philips Guarantee in Central and Eastern Europe applies within Czech Republic, Hungary,
Slovakia, Slovenia, Poland, Russia and Turkey and only for monitors originally designed,
manufactured, approved and/or authorized for usage within these countries.
Warranty coverage begins as from the day you buy your monitor. For 3 years thereafter, your
monitor will be serviced in case of defects provided for under the warranty coverage.
What is excluded?
The Philips guarantee applies provided the product is handled properly for its intended use, in
accordance with its operating instructions and upon presentation of the original invoice or cash
receipt, indicating the date of purchase, dealer's name and model and production number of the
product.
The Philips guarantee may not apply if:
●
●
●
●
●
●
●
the documents have been altered in any way or made illegible;
the model or production number on the product has been altered, deleted, removed or made
illegible;
repairs or product modifications and alterations have been executed by unauthorized service
organizations or persons;
damage is caused by accidents including but not limited to lightning, water or fire, misuse or
neglect.
Reception problems caused by signal conditions or cable or antenna systems outside the
unit;
Defects caused by abuse or misuse of the monitor;
Product requires modification or adaptation to enable it to comply with local or national
technical standards, which apply in countries for which the product was not originally
designed, manufactured, approved and/or authorized. Therefore always check whether a
product can be used in a specific country.
Please note that the product is not defective under this guarantee in the case where modifications
become necessary in order for the product to comply with local or national technical standards
which apply in countries for which the product was not originally designed and/or manufactured.
file:///D|/My%20Documents/dfu/190G6/english/warranty/war_ee.htm (1 of 2)2005-08-23 1:19:31 PM
Your Guarantee in Central and Eastern Europe
Therefore always check whether a product can be used in a specific country.
Just a click away
In case of any problems, we advise you to read the operating instructions carefully or go to the www.
philips.com/support website for additional support.
Just a phone call away
In order to avoid unnecessary inconvenience, we advise you to read the operating instructions
carefully before contacting our dealers or Information Centers
In case your Philips product is not working correctly or is defective, please contact your Philips
dealer or directly the Philips Service and Consumer Information Centers
Website: http://www.philips.com/support
file:///D|/My%20Documents/dfu/190G6/english/warranty/war_ee.htm (2 of 2)2005-08-23 1:19:31 PM
International Guarantee
Your International Guarantee
Dear Customer,
Thank you for purchasing this Philips product which has been designed and manufactured to the
highest quality standards.
If, unfortunately, something should go wrong with this product Philips guarantees free of charge
labor and replacement parts irrespective of the country where it is repaired during a period of 12
months from date of purchase. This international Philips guarantee complements the existing
national guarantee obligations to you of dealers and Philips in the country of purchase and does not
affect your statutory rights as a customer.
The Philips guarantee applies provided the product is handled properly for its intended use, in
accordance with its operating instructions and upon presentation of the original invoice or cash
receipt, indicating the date of purchase, dealer's name and model and production number of the
product.
The Philips guarantee may not apply if:
●
●
●
●
the documents have been altered in any way or made illegible;
the model or production number on the product has been altered, deleted, removed or made
illegible;
repairs or product modifications and alterations have been executed by unauthorized service
organizations or persons;
damage is caused by accidents including but not limited to lightning, water or fire, misuse or
neglect.
Please note that the product is not defective under this guarantee in the case where modifications
become necessary in order for the product to comply with local or national technical standards
which apply in countries for which the product was not originally designed and/or manufactured.
Therefore always check whether a product can be used in a specific country.
In case your Philips product is not working correctly or is defective, please contact your Philips
dealer. In the event you require service whilst in another country a dealer address can be given to
you by the Philips Consumer Help Desk in that country, the telephone and fax number of which can
be found in the relevant part of this booklet.
In order to avoid unnecessary inconvenience, we advise you to read the operating instructions
carefully before contacting your dealer. If you have questions which your dealer cannot answer or
any related question please contact the Philips Consumer Information Centers or via:
Website: http://www.philips.com
file:///D|/My%20Documents/dfu/190G6/english/warranty/war_intl.htm (1 of 2)2005-08-23 1:19:32 PM
International Guarantee
file:///D|/My%20Documents/dfu/190G6/english/warranty/war_intl.htm (2 of 2)2005-08-23 1:19:32 PM
United States Guarantee
Your Philips F1rst Choice Warranty(Canada/USA)
Thank you for purchasing this Philips monitor.
All Philips monitors are designed and manufactured to high standards and
deliver high-quality performance, ease of use and ease of installation. Should
you encounter any difficulties while installing or using this product, please
contact Philips directly to benefit from your Philips F1rst Choice Warranty.
This three-year service warranty entitles you to a swap model on-site within
48 hours of your call being received within the first year of purchase. If you
have any problems with your monitor within the second or third year of
purchase, we will repair it after it has been sent to the service provider at your
expense and returned to you within five working days, free of charge.
LIMITED WARRANTY (Computer Monitor)
Click here to access the Warranty Registration Card.
Three Years Free Labor / Three Years Free Service on Parts / One Year Exchange*
*Product will be exchanged with a new or renewed to original specifications unit within two
business days for the first year. This product must be shipped in at your expense for service during
years two and three.
WHO IS COVERED?
You must have proof of purchase to receive warranty service. A sales receipt or other document
showing that you purchased the product is considered proof of purchase. Attach it to this owner's
manual and keep both nearby.
WHAT IS COVERED?
Warranty coverage begins the day you buy your product. For three years thereafter, all parts will be
repaired or replaced, and labor is free. After three years from the day of purchase, you pay for the
replacement or repair of all parts, and for all labor charges.
All parts, including repaired and replaced parts, are covered only for the original warranty period.
When the warranty on the original product expires, the warranty on all replaced and repaired
products and parts also expires.
WHAT IS EXCLUDED?
file:///D|/My%20Documents/dfu/190G6/english/warranty/war_usa.htm (1 of 4)2005-08-23 1:19:32 PM
United States Guarantee
Your warranty does not cover:
●
●
●
●
●
●
●
labor charges for installation or setup of the product, adjustment of customer controls on the
product, and installation or repair of antenna systems outside of the product.
product repair and/or part replacement because of misuse, accident, unauthorized repair or
other cause not within the control of Philips Consumer Electronics.
reception problems caused by signal conditions or cable or antenna systems outside the
unit.
a product that requires modification or adaptation to enable it to operate in any country other
than the country for which it was designed, manufactured, approved and/or authorized, or
repair of products damaged by these modifications.
incidental or consequential damages resulting from the product. (Some states do not allow
the exclusion of incidental or consequential damages, so the above exclusion may not apply
to you. This includes, but is not limited to, prerecorded material, whether copyrighted or not
copyrighted.)
a product used for commercial or institutional purposes.
the model or production number on the product has been altered, deleted, removed or made
illegible.
Where IS SERVICE AVAILABLE?
Warranty service is available in all countries where the product is officially distributed by Philips
Consumer Electronics. In countries where Philips Consumer Electronics does not distribute the
product, the local Philips service organization will attempt to provide service (although there may be
a delay if the appropriate spare parts and technical manual(s) are not readily available).
Where CAN I GET MORE INFORMATION?
For more information, contact the Philips Customer Care Center by calling (877) 835-1838 (U.S.A.
customers only) or (919) 573-7855.
Before Requesting Service...
Please check your owner's manual before requesting service. Adjustments of the controls
discussed there may save you a service call.
TO GET WARRANTY SERVICE IN U.S.A., PUERTO RICO OR U.S. VIRGIN ISLANDS...
Contact the Philips Customer Care Center phone number listed below for product assistance and
procedures for servicing:
Philips Customer Care Center
file:///D|/My%20Documents/dfu/190G6/english/warranty/war_usa.htm (2 of 4)2005-08-23 1:19:32 PM
United States Guarantee
(877) 835-1838 or (919) 573-7855
(In U.S.A., Puerto Rico and U.S. Virgin Islands, all implied warranties, including implied warranties
of merchantability and fitness for a particular purpose, are limited in duration to the duration of this
express warranty. But, because some states do not allow limitations on how long an implied
warranty may last, this limitation may not apply to you.)
TO GET WARRANTY SERVICE IN CANADA...
Please contact Philips at:
(800) 479-6696
Three years free parts and three years free labor will be provided at Philips Canada depot or any
one of its authorized service centers.
(In Canada, this warranty is given in lieu of all other warranties. No other warranties are expressed
or implied, including any implied warranties of merchantability or fitness for a particular purpose.
Philips is not liable under any circumstances for any direct, indirect, special, incidental or
consequential damages, howsoever incurred, even if notified of the possibility of such damages.)
REMEMBER... Please record the model and serial numbers found on the product below.
MODEL # ________________________________________________
SERIAL # ________________________________________________
This warranty gives you specific legal rights. You may have other rights which vary from state/
province to state/province.
Before contacting Philips, please prepare the following details so we can solve your problem
quickly.
●
●
●
●
Philips type number
Philips serial number
Purchase date (copy of purchase may be required)
PC environment Processor:
❍
❍
❍
286/386/486/Pentium Pro/Internal memory
Operating system (Windows, DOS, OS/2, MAC)
Fax/Modem/Internet program?
file:///D|/My%20Documents/dfu/190G6/english/warranty/war_usa.htm (3 of 4)2005-08-23 1:19:32 PM
United States Guarantee
●
●
●
Other cards installed
Having the following information available will also help speed up the process:
Your proof of purchase indicating: date of purchase, dealer name, model and product serial
number.
The full address to which the swap model should be delivered.
Just a phone call away
Philips’ customer help desks are located worldwide. Within the U.S. you can contact Philips
customer care Monday-Friday from 8:00 AM-9:00 PM Eastern Time (ET) and on Saturdays from
10:00 AM-5:00 PM ET hrs by using one of the contact phone numbers.
For more information on this and more great Philips products visit our website at:
Website: http://www.philips.com
file:///D|/My%20Documents/dfu/190G6/english/warranty/war_usa.htm (4 of 4)2005-08-23 1:19:32 PM
F1rst Choice Contact Information
F1rst Choice Contact Information
Country
Telephone number
Tariff
Austria
0820 901115
0.20
Belgium
070 253 010
0.17
Cyprus
800 92256
Free of Charge
Denmark
3525 8761
Local call tariff
Finland
09 2290 1908
Local call tariff
France
08 9165 0006
0.23
Germany
0180 5 007 532
0.12
Greece
00800 3122 1223
Local call tariff
Ireland
01 601 1161
Local call tariff
Italy
199 404 042
0.25
Luxembourg
26 84 30 00
Local call tariff
The Netherlands
0900 0400 063
0.20
Norway
2270 8250
Local call tariff
Portugal
2 1359 1440
Local call tariff
Spain
902 888 785
0.15
Sweden
08 632 0016
Local call tariff
Switzerland
02 2310 2116
Local call tariff
United Kingdom
0906 1010 017
£0.15
file:///D|/My%20Documents/dfu/190G6/english/warranty/warfirst.htm2005-08-23 1:19:39 PM
Consumer Information Centers
Consumer Information Centers
Antilles • Argentina • Australia • Bangladesh • Brasil • Canada • Chile • China • Colombia •
Belarus • Bulgaria • Croatia • Czech Republic • Estonia • Dubai • Hong Kong • Hungary •
India • Indonesia • Korea • Latvia • Lithuania • Malaysia • Mexico • Morocco • New Zealand
• Pakistan • Paraguay • Peru • Philippines • Poland • Romania • Russia • Serbia &
Montenegro • Singapore • Slovakia • Slovenia • South Africa • Taiwan • Thailand • Turkey •
Ukraine • Uruguay • Venezuela
Eastern Europe
BELARUS
Technical Center of JV IBA
M. Bogdanovich str. 155
BY - 220040 Minsk
Tel: +375 17 217 33 86
BULGARIA
LAN Service
140, Mimi Balkanska Str.
Office center Translog
1540 Sofia, Bulgaria
Tel: +359 2 960 2360
www.lan-service.bg
CZECH REPUBLIC
Xpectrum
Lužná 591/4
CZ - 160 00 Praha 6 Tel: 800 100 697
Email:[email protected]
www.xpectrum.cz
CROATIA
Renoprom d.o.o.
Mlinska 5, Strmec
HR - 41430 Samobor
Tel: +385 1 333 0974
file:///D|/My%20Documents/dfu/190G6/english/warranty/warcic.htm (1 of 11)2005-08-23 1:19:45 PM
Consumer Information Centers
ESTONIA
FUJITSU SERVICES OU
Akadeemia tee 21G
EE-12618 Tallinn
Tel: +372 6519900
www.ee.invia.fujitsu.com
HUNGARY
Serware Szerviz
Vizimolnár u. 2-4
HU - 1031 Budapest
Tel: +36 1 2426331
Email: [email protected]
www.serware.hu
LATVIA
ServiceNet LV
Jelgavas iela 36
LV - 1055 Riga,
Tel: +371 7460399
Email: [email protected]
LITHUANIA
ServiceNet LT
Gaiziunu G. 3
LT - 3009 KAUNAS
Tel: +370 7400088
Email: [email protected]
www.servicenet.lt
ROMANIA
Blue Ridge Int'l Computers SRL
115, Mihai Eminescu St., Sector 2
RO - 020074 Bucharest
Tel: +40 21 2101969
SERBIA & MONTENEGRO
Tehnicom Service d.o.o.
Bulevar Vojvode Misica 37B
YU - 11000 Belgrade
Tel: +381 11 3060 886
file:///D|/My%20Documents/dfu/190G6/english/warranty/warcic.htm (2 of 11)2005-08-23 1:19:45 PM
Consumer Information Centers
SLOVAKIA
Datalan Servisne Stredisko
Puchovska 8
SK - 831 06 Bratislava
Tel: +421 2 49207155
Email: [email protected]
SLOVENIA
PC HAND
Brezovce 10
SI - 1236 Trzin
Tel: +386 1 530 08 24
Email: [email protected]
POLAND
Zolter
ul.Zytnia 1
PL - 05-500 Piaseczno
Tel: +48 22 7501766
Email: [email protected]
www.zolter.com.pl
RUSSIA
Tel: +7 095 961-1111
Tel: 8-800-200-0880
Website: www.philips.ru
TURKEY
Türk Philips Ticaret A.S.
Yukari Dudullu Org.San.Bolgesi
2.Cadde No:22
34776-Umraniye/Istanbul
Tel: (0800)-261 33 02
file:///D|/My%20Documents/dfu/190G6/english/warranty/warcic.htm (3 of 11)2005-08-23 1:19:45 PM
Consumer Information Centers
UKRAINE
Comel
Shevchenko street 32
UA - 49030 Dnepropetrovsk
Tel: +380 562320045
www.csp-comel.com
Latin America
ANTILLES
Philips Antillana N.V.
Kaminda A.J.E. Kusters 4
Zeelandia, P.O. box 3523-3051
Willemstad, Curacao
Phone: (09)-4612799
Fax : (09)-4612772
ARGENTINA
Philips Antillana N.V.
Vedia 3892 Capital Federal
CP: 1430 Buenos Aires
Phone/Fax: (011)-4544 2047
BRASIL
Philips da Amazônia Ind. Elet. Ltda.
Rua Verbo Divino, 1400-São Paulo-SP
CEP-04719-002
Phones: 11 21210203 -São Paulo & 0800-701-0203-Other Regions without São Paulo City
CHILE
Philips Chilena S.A.
Avenida Santa Maria 0760
P.O. box 2687Santiago de Chile
Phone: (02)-730 2000
Fax : (02)-777 6730
file:///D|/My%20Documents/dfu/190G6/english/warranty/warcic.htm (4 of 11)2005-08-23 1:19:45 PM
Consumer Information Centers
COLOMBIA
Industrias Philips de Colombia
S.A.-Division de Servicio
CARRERA 15 Nr. 104-33
Bogota, Colombia
Phone:(01)-8000 111001 (toll free)
Fax : (01)-619-4300/619-4104
MEXICO
Consumer Information Centre
Norte 45 No.669
Col. Industrial Vallejo
C.P.02300, -Mexico, D.F.
Phone: (05)-3687788 / 9180050462
Fax : (05)-7284272
PARAGUAY
Av. Rca. Argentina 1780 c/Alfredo Seiferheld
P.O. Box 605
Phone: (595 21) 664 333
Fax: (595 21) 664 336
Customer Desk:
Phone: 009 800 54 1 0004
PERU
Philips Peruana S.A.
Customer Desk
Comandante Espinar 719
Casilla 1841
Limab18
Phone: (01)-2136200
Fax : (01)-2136276
file:///D|/My%20Documents/dfu/190G6/english/warranty/warcic.htm (5 of 11)2005-08-23 1:19:45 PM
Consumer Information Centers
URUGUAY
Rambla O'Higgins 5303 Montevideo
Uruguay
Phone: (598) 619 66 66
Fax: (598) 619 77 77
Customer Desk:
Phone: 0004054176
VENEZUELA
Industrias Venezolanas Philips S.A.
Apartado Postal 1167
Caracas 1010-A
Phone: (02) 2377575
Fax : (02) 2376420
Canada
CANADA
Philips Electronics Ltd.
281 Hillmount Road
Markham, Ontario L6C 2S3
Phone: (800) 479-6696
Pacific
AUSTRALIA
Philips Consumer Electronics
Consumer Care Center
Level 1, 65 Epping Rd
North Ryde NSW 2113
Phone: 1300 363 391
Fax : +61 2 9947 0063
file:///D|/My%20Documents/dfu/190G6/english/warranty/warcic.htm (6 of 11)2005-08-23 1:19:45 PM
Consumer Information Centers
NEW ZEALAND
Philips New Zealand Ltd.
Consumer Help Desk
2 Wagener Place, Mt.Albert
P.O. box 1041
Auckland
Phone: 0800 477 999 (toll free)
Fax : 0800 288 588
Asia
BANGLADESH
Philips Service Centre
100 Kazi Nazrul Islam
Avenue Kawran Bazar C/A
Dhaka-1215
Phone: (02)-812909
Fax : (02)-813062
CHINA
SHANGHAI
Rm 1007, Hongyun Building, No. 501 Wuning road,
200063 Shanghai P.R. China
Phone: 4008 800 008
Fax: 21-52710058
HONG KONG
Philips Electronics Hong Kong Limited
Consumer Service
Unit A, 10/F. Park Sun Building
103-107 Wo Yi Hop Road
Kwai Chung, N.T.
Hong Kong
Phone: (852)26199663
Fax: (852)24815847
file:///D|/My%20Documents/dfu/190G6/english/warranty/warcic.htm (7 of 11)2005-08-23 1:19:45 PM
Consumer Information Centers
INDIA
Phone: 91-20-712 2048 ext: 2765
Fax: 91-20-712 1558
BOMBAY
Philips India
Customer Relation Centre
Bandbox House
254-D Dr. A Besant Road, Worli
Bombay 400 025
CALCUTTA
Customer Relation Centre
7 justice Chandra Madhab Road
Calcutta 700 020
MADRAS
Customer Relation Centre
3, Haddows Road
Madras 600 006
NEW DELHI
Customer Relation Centre
68, Shivaji Marg
New Dehli 110 015
INDONESIA
Philips Group of Companies in Indonesia
Consumer Information Centre
Jl.Buncit Raya Kav. 99-100
12510 Jakarta
Phone: (021)-7940040 ext: 2100
Fax : (021)-794 7511 / 794 7539
file:///D|/My%20Documents/dfu/190G6/english/warranty/warcic.htm (8 of 11)2005-08-23 1:19:45 PM
Consumer Information Centers
KOREA
Philips Korea Ltd.
Philips House
C.P.O. box 3680
260-199, Itaewon-Dong.
Yongsan-Ku, Seoul 140-202
Phone: 080 600 6600 (toll free)
Fax : (02) 709 1210
MALAYSIA
After Market Solutions Sdn Bhd,
Philips Authorised Service Center,
Lot 6, Jalan 225, Section 51A,
46100 Petaling Jaya,
Selangor Darul Ehsan,
Malaysia.
Phone: (603)-7954 9691/7956 3695
Fax: (603)-7954 8504
Customer Careline: 1800-880-180
PAKISTAN
Philips Consumer Service
Mubarak manzil,
39, Garden Road, Saddar,
Karachi-74400
Tel: (9221) 2737411-16
Fax: (9221) 2721167
E-mail: [email protected]
Website: www.philips.com.pk
PHILIPPINES
PHILIPS ELECTRONICS & LIGHTING, INC.
Consumer Electronics
48F PBCOM tower
6795 Ayala Avenue cor VA Rufino St.
Salcedo Village
1227 Makati City, PHILS
Phone: (02)-888 0572, Domestic Toll Free: 1-800-10-PHILIPS or 1-800-10-744 5477
Fax: (02)-888 0571
file:///D|/My%20Documents/dfu/190G6/english/warranty/warcic.htm (9 of 11)2005-08-23 1:19:45 PM
Consumer Information Centers
SINGAPORE
Accord Customer Care Solutions Ltd
Authorized Philips Service Center
Consumer Service
620A Lorong 1 Toa Rayoh
Singapore 319762
Tel: +65 6882 3999
Fax: +65 6250 8037
TAIWAN
Philips Taiwan Ltd.
Consumer Information Centre
13F, No. 3-1 Yuan Qu St., Nan Gang Dist.,
Taipei 115, Taiwan
Phone: 0800-231-099
Fax : (02)-3789-2641
THAILAND
Philips Electronics (Thailand) Ltd.
26-28th floor, Thai Summit Tower
1768 New Petchburi Road
Khwaeng Bangkapi, Khet Huaykhwang
Bangkok10320 Thailand
Tel: (66)2-6528652
E-mail: cic [email protected]
Africa
MOROCCO
Philips Electronique Maroc
304,BD Mohamed V
Casablanca
Phone: (02)-302992
Fax : (02)-303446
file:///D|/My%20Documents/dfu/190G6/english/warranty/warcic.htm (10 of 11)2005-08-23 1:19:45 PM
Consumer Information Centers
SOUTH AFRICA
PHILIPS SA (PTY) LTD
Customer Care Center
195 Main Road
Martindale, Johannesburg
P.O. box 58088
Newville 2114
Telephone: +27 (0) 11 471 5194
Fax: +27 (0) 11 471 5123
E-mail: [email protected]
Middle East
DUBAI
Philips Middle East B.V.
Consumer Information Centre
P.O.Box 7785
DUBAI
Phone: (04)-335 3666
Fax : (04)-335 3999
file:///D|/My%20Documents/dfu/190G6/english/warranty/warcic.htm (11 of 11)2005-08-23 1:19:45 PM
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement