1 You are replacing a wired thermostat

1 You are replacing a wired thermostat
1
You are replacing a wired thermostat
You can watch this installation on:
http://netatmo.com/video1
Warning
Warning!
• Read carefully these instructions before starting the installation.
• The Netatmo Thermostat must be installed according to
applicable standards.
• Before any intervention, make sure power is turned off.
In the box
Thermostat
(Mobile stand)*
Relay
(Boiler adapter)*
Mounting Plate
Color Adhesives
Trim plate
Mains adapter
(Tape)*
Cover
3 AAA batteries
4 screws
4 screw anchors
* not used in this setup
1 USB cable
Relay
1
Plug the mains adapter
in the relay.
3
The relay blinks blue.
2
Connect the relay to a wall
socket in the same room
as your existing thermostat.
4
Switch off the power supply.
Identify
1
Remove the cover of your old
thermostat.
Take a picture of the wiring.
2
- If there are only two wires, they are the
control wires and are useful in this setup.
- If there are more than two wires, identify
the two control wires. They are usually
black or grey.
The wires can be identified as shown on
the following diagram
Note: if there are more than two wires, the
others are power supply wires and are useless
here. They are usually brown, blue, green or
yellow.
In doubt, please send a picture at [email protected]
netatmo.com and our support team will help
you identify the right wires.
Control wires
Usually black
or grey wires
COM / NO
Power supply wires
Usually blue and
brown wires
P/N
ou
L/N
Replace
1
Disconnect your former thermostat.
Remove it from the wall.
2
Pass the wires through the Netatmo mounting plate and screw the latter to the wall.
To hide potential scratches and holes left
behind, use the trim plate.
3
Screw the control wires previously identified
into the electrical terminals and insulate the
unused wires.
Place and screw the protection cover onto
the electrical terminals.
Customisation
1
You can choose to customise your Thermostat
by using one of the colour adhesives.
2
Take off the outer frame of the adhesive.
3
Stick it on the back of your Thermostat.
Thermostat
1
Insert the batteries in the Thermostat.
2
Set the Thermostat on the mounting plate.
3
Switch the power supply back on.
Thermostat
The Thermostat displays the start screen
and searches for the relay.
+
21
20
5
0
+
Consigne
Température
If the Thermostat has found the
relay, it displays the setpoint and
the room temperatures.
ou
21
20
5
0
If the Thermostat hasn’t found the
relay, it displays the «!» symbol.
In this case, move the relay closer to
the Thermostat and wait until the «!»
symbol disappears.
Test
1
Push several times the top of the
Thermostat until it displays « MAX ».
The Thermostat switches the boiler
on.
clic
+
21
20
+
5
0
20
0
2
Push several times the bottom of the
Thermostat until it displays « OFF ».
The Thermostat switches the boiler
off.
+
+
20
20
0
0
clic
Note: if the Thermostat doesn’t switch on and off the boiler, the control wires have been
incorrectly wired. In this case, check your wiring using the picture of your old thermostat’s
wiring to identify the right control wires.
App
To control and program your Thermostat from your smartphone, tablet or computer, visit:
http://thermostat.netatmo.com
PC / Mac
Smartphone / Tablettes
Specifications
SIZE
Thermostat : 83x83x22 mm
DESIGN
Designed by Starck.
Translucent minimalist plexiglass cube.
5 interchangeable colors in the box.
SENSORS AND MEASUREMENTS
Température (measurement):
Ranges from 0°C to 50°C
Accuracy: +- 0.5° C
Température (setpoint):
Ranges from 7°C to 30°C
Increment: 0.5°C
Unit: °C
E-INK DISPLAY
Energy efficient, longer battery life and
optimal readability.
FREE APP, LIFETIME SUPPORT
No subscription fee.
App available on the App Store and on
Google Play.
Free access to your online personal
dashboard.
Accessible from multiple devices.
WIRELESS SPECIFICATIONS
Wi-Fi 802.11 b/g/n compatible (2.4GHz).
Supported security: Open/WEP/WPA/
WPA2-personal (TKIP and AES). Wireless connection between thermostat and relay:
radio long range 100m.
POWER AND BATTERIES
3 AAA batteries.
1 year battery life.
SETUP AND COMPATIBILITY
Compatible with gas, fuel and wood boilers.
Switching current: max 4 A
Switching voltage: max 250 VAC
Switching power: max 120 W
COMPATIBLE WITH IPHONE AND IPAD
iPhone 4, iPhone 4s, iPhone 5, iPhone 5c / 5s
iPad mini, iPad mini with Retina display, iPad 2,
iPad (3rd generation), iPad (4th generation),
iPad Air
iPod touch (5th generation)
COMPATIBLE WITH ANDROID SMARTPHONE
Android 4.0 required
EU Declaration of Conformity
We, Netatmo, declare that this device is in compliance with the essential
requirements and other relevant provisions of Directive 1999/5/EC.
EU Declaration of Conformity
We, Netatmo, declare that this device is in compliance with the essential requirements and other
relevant provisions of Directive 1999/5/EC.
Safety warnings
This device must be installed according to the applicable norms.
Use only with supplied power plug adaptor and boiler adaptor. This device is for indoor use only.
Before inserting the batteries, check that the contacts in the device and on the batteries are
clean, and clean them if necessary. Note the polarity (+/-) when inserting the batteries.
Do not throw the batteries into a fire, short-circuit it or dismantle it. Keep children away from
Canadian Compliance Statement
batteries. Seek medical attention immediately if a battery
is swallowed.
This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject
to the
two conditions: (1) this device may not
Do not attempt to repair the device yourself; an after-sales
service
isfollowing
available.
cause interference, and (2) this device must accept any interference, including
Any changes or modifications to this unit not expressly
the operation
party responsible
for
interferenceapproved
that may causeby
undesired
of the device.
Cet appareil
est conforme aux normes CNR exemptes de licence d'Industrie
compliance could void the user’s authority to operate
the equipment.
Canada. Le fonctionnement est soumis aux deux conditions suivantes: (1) cet
FCC Radiation Exposure Statement
Thermostat and relay insulation: class II devices. appareil ne doit pas provoquer d'interférences et (2) cet appareil doit accepter
This equipment complies with FCC RF radiation exposure limits set forth for an
toute interférence, y compris celles susceptibles de provoquer un fonctionnement
uncontrolled
transmitter
shouldfor
be installed
andpersons
operated
Thisenvironment.
device isThisnot
intended
use by
(including
children) with reduced physical, sensory
non souhaité de l'appareil.
with a minimum distance of 20 centimeters between the radiator and your
Thisknowledge,
Class B digital apparatus
complies
with Canadian
or
mental
capabilities,
or
lack
of
experience
and
unless
they
have ICES-003.
been given
body and must not be co-located or operating in conjunction with any other
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du
antennasupervision
or transmitter. Thisor
equipment
compliesconcerning
with Part 15 of theuse
FCC Rules.
instruction
of the appliance
Canada. by a person responsible for their safety.
Operation is subject to the following two conditions:
This device and its antenna(s) must not be co-located or operating in
be interference,
supervised
(1) This Children
device may notshould
cause harmful
and to ensure that they do not play with the appliance.
conjunction with any other antenna or transmitter.
(2) This device must accept any interference received, including interference
Legal notice
Cet appareil et son antenne (s) ne doit pas être co-localisés ou fonctionnant en
that may cause undesired operation.
conjonction avec une autre antenne ou transmetteur.
“Made for iPod”, “Made for iPhone”, “Made for iPad”
mean that an electronic accessory has
Taiwan Wireless Statements
been designed to connect specifically to iPod, iPhone
and iPad and has been certified by the
無線設備的警告聲明
developer to meet Apple performance standards. 本產品符合低功率電波輻射性電機管理辦法 第〸二條、第〸四條等
Apple is not responsible for the operation of
條文規定: this device or its compliance with safety and regulatory
standards.
1. 經型式認證合格之低功率射頻電機,非經許可,公司、商號或使
用�均不得擅自變更頻率、加大功率或變更原設計之特性及功能。 Please note that the use of this accessory with iPhone
may affect wireless performance.
2. 低功率射頻電機之使用不得影�飛航安全及干擾合法通信;經發
現有干擾現象時,應立即停用,並改善至無干擾時方得繼續使用。 前項合法通信,指依電信法規定作業之無線電通信。 低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性
電機設備之干擾。
Complies with
IDA Standards
V16
Copyright Netatmo © 2013 All rights reserved. Reproduction and distribution prohibited without written authorization from Netatmo.
V2
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement