Philips 27MS5402 Flat Panel Television Setup guide


Add to my manuals
4 Pages

advertisement

Philips 27MS5402 Flat Panel Television Setup guide | Manualzz

9

10

11

12

1

8

2

3

4

7

6

5

T ABLE OF C ONTENTS

Getting Started

Warning/Important Notice . . . . . . . . . . . . .1

Basic Cable Television Connection . . . . . . .1

Setting your TV for the first time . . . . . . . . . . . . .3-4

Using the On-screen menu . . . . . . . . . . . . . . . . . . . .3

Using the Language Control . . . . . . . . . . . . . . . . . .3

Basic Antenna Television Connection . . . . . . . . . . . .1

Basic VCR/Accessory Device Connection . . . . . . . .1

Basic Television Operation . . . . . . . . . . . . . . . . . . . .2

Basic Remote Control Operation . . . . . . . . . . . . . . .2

Setting the Tuner Mode Control . . . . . . . . . . . . . . .3

How to Automatically Program Channels . . . . . . . .3

How to Add and Delete Channels . . . . . . . . . . . . . .4

IMPORTANT

NOTE: This owner's manual is used with several different television models. Not all features (and drawings) discussed in this manual will necessarily match those found with your television set.

This is normal and does not require you contacting your dealer or requesting service.

WARNING: TO PREVENT FIRE OR SHOCK

HAZARD DO NOT EXPOSE THIS UNIT TO

RAIN OR EXCESSIVE MOISTURE.

B

ASIC

T

ELEVISION

C

ONNECTIONS

C ABLE TV

C

ABLE

I

NPUT

/C

ONVERTER

Y

our Cable TV input into your home may be a single (75 ohm) cable, or a

Converter Box installation.

In either case the connection to the TV is very easy.

Just put the threaded end of the cable signal to the

TV's antenna plug and screw it down tight.

NOTE: The connecting cable for the Converter is supplied from the Cable TV Company.

If your Cable TV signal

is a single round cable (75 ohm) then you're ready to connect to the TV.

If you have a Cable

Converter Box:

Connect the Cable TV signal to the Cable Signal IN(put) plug on the Converter.

Cable TV Company

Cable TV Converter

Box Connection

IN

Connect the Cable TV cable to the ANTENNA/CABLE plug on the TV.

If you have a Cable Converter Box:

Connect the OUT(put) plug from the

Converter to the 75

Ω plug on the TV.

Cable TV Signal Input

75 V

OUT

OR

Round Cable

75

Ohm

1

2

Back of TV

VIDEO

Monitor out AV1 in

COMPONENT VIDEO INPUT

Y L/

Mono

AUDIO Pb

R Pr

S-VIDEO

S

MART

H

ELP

Remember:

Set the TV for the type signal you've just connected (see the “Tuner Mode” section on page 3 of this Set-Up Guide.)

To select only the channel numbers on your Cable system see “Auto Program"

(page 4). If you use a

Cable Converter box, set the TV to the same channel as the converter's CH 3/4 switch (on the rear of the converter.)

A NTENNA

C

OMBINATION

UHF/VHF

A

combination antenna receives normal broadcast channels (VHF 2-13 and UHF 14-69). Your connection is easy since there is only one 75

(ohm) antenna plug on the back of your TV - and that’s where the antenna goes.

Combination VHF/UHF

Antenna

(Outdoor or Indoor)

If your antenna has a

round cable (75 ohm) on the end, then you're ready to connect it to the TV.

If your antenna has flat twin-lead

wire (300 ohm), you first need to attach the antenna wires to the screws on a 300 to 75 ohm adapter.

1

Twin Lead

Wire

Round Cable

75

300 to 75

Adapter

75 V

OR

Push the round end of the adapter (or antenna) onto the

75

Ω plug on the rear of the TV.

If the round end of the antenna wire is threaded, screw it down finger tight.

2

Back of TV

75 V

Monitor out AV1 in

COMPONENT VIDEO INPUT

VIDEO

Y L/

Mono

AUDIO Pb

R Pr

S-VIDEO

Note: For homes with separate UHF and VHF antennas you will need an optional combiner to connect to the TV.

U/V

Combiner

75 AV1 in

VIDEO

Monitor out

COMPONENT VIDEO INPUT

Mono

AUDIO S-VIDEO

Back of TV

75-300 Ohm Adapter

S

MART

H

ELP

Remember, be sure to set the TV for the type signal you've connected

(see the “Tuner

Mode” section on page 3 of this Set-

Up Guide.)

To set the TV to select only the channel numbers in your area see how to

“Program" or "Add" channels in memory on page 4 (Auto

Program section).

To order any optional accessory contact your dealer or call the toll-free accessory ordering number

(1-800-851-8885).

TV

TO

VCR

B

ASIC

C

ONNECTION

he basic Antenna, or

T

Cable TV, to VCR to

TV connection is shown to the right. For more information on other hookups

(possible when Cable

Converter/Descrambler boxes are included) refer to your accessory VCR and

Cable Converter Owner's

Manual for details.

Connect your

Antenna or Cable TV signal to the IN FROM ANT(enna) plug on the VCR.

Outdoor

VHF/UHF

Antenna

Connect the OUT TO

TV plug on the VCR to the

75

Ω plug on the TV (connecting cable supplied with the

VCR.)

300 to 75

Ohm Adapter

1

Round Cable

75

Supplied with VCR

Refer to the Owner's

Manual included with your

VCR for other possible connections and TV/VCR operating details.

2

OR

75 V

IN FROM ANT.

OUT TO TV

Cable TV signal

Back of TV

75 V

VIDEO

Monitor out AV1 in

COMPONENT VIDEO INPUT

Y

Mono

L/

AUDIO Pb

R Pr

S-VIDEO

VCR

3121 233 41211

TV/VCR/ACC M

ODE

S

WITCH

The remote's TV/VCR/ACC

Switch controls how buttons on the remote are used.

For example:

With the switch in the "TV"

position: the Menu, CURSOR ©,

©© , §§ and ■ buttons are used to select and adjust on-screen TV features.

With the switch in the

"ACC" position: the Power, Channel

Number, and Channel

Up (+) /Down (–) buttons on the remote work with

Cable TV Converters.

With the switch in the

"VCR" position: the Menu, CURSOR ©,

©© , §§ and ■ buttons on the remote work Stop,

Play, Fast Forward, and other VCR features.

Note: For more details on how the TV remote works with VCRs and Cable

Converters, see the other owner's manual supplied with your TV.

T ELEVISION

B

ASIC

TV

AND

R

EMOTE

C

ONTROL

O

PERATION

Press the Power but-

ton to turn the TV ON.

Press the Volume + or –

buttons to increase or decrease the TV sound. Press both at the same time to display the TV’s on-screen menu

Press the CH or buttons to select TV channels.

These buttons can also be used to make adjustments or selections within the on-screen menu.

S

MART

H

ELP

You can press any button on the front of the TV to turn the TV ON.

The tuned channel number will always briefly appear when the TV is first turned

ON (and with channel changes).

2

REMOTE SENSOR WINDOW

POWER

– VOL +

MENU

– CH +

1

3

R EMOTE

- B ATTERIES /O PERATION

T o load the supplied batteries into the remote:

1. Remove the battery compartment

lid on the back of the remote.

2. Place the batteries (2- AA) in the

remote. Be sure the (+) and (-) ends of the batteries line up correctly (inside of case is marked).

3. Reattach the battery lid.

Battery

Compartment

Lid

Press the TV button on the

remote control, then point the remote at the remote sensor window when operating the TV with the remote control.

VOL

4

S

MART

H

ELP

Just a couple of reminders about the

STATUS/EXIT button; you can press the STATUS/EXIT button (on the remote) to see what channel the TV is ON, what sound mode (stereo or mono) is present or to remove the on-screen menu from the TV’s screen at any time.

QUADRA SURF Buttons - (Red, Green,

Yellow, Blue) Allows you to store and surf up to 10 channels you choose for each colored button.

SMILEY Button - Press to add channels in the “Quadra Surf” lists. Works with all colored buttons.

TV/VCR/ACC MODE SWITCH - Slide to position of TV to control TV functions,

VCR to control VCR functions and ACC for Cable Converter, DBS, DVD, etc., functions.

AUTO SOUND Button - Press repeatedly to choose from different factory predefined sound settings. Choose from

Personal (how you set the Sound Menu options), Voice (for programming with speaking only), Music (for musical type programs such as concerts), or Theatre

(used when watching movies).

MENU Button - Press to display the onscreen menu. Also can be used to back out of the on-screen menu until it disappears from the TV’s screen.

VOL(ume) + or – Buttons - Press the

VOL + button to increase the TV’s sound level. Press the VOL – button to decrease the TV’s sound level.

MUTE Button - Press the mute button to eliminate the sound being heard from the

TV. “MUTE” will be displayed on the

TV’s screen. Press again to restore the

TV’s volume to it’s previous level.

CLOCK(TV/VCR) Button - Press to display the “Timer” menu when in the TV mode. Within this menu set the time, set the TV to tune to a certain channel at a certain time once, or daily. When in the

VCR Mode, press to toggle between VCR viewing and TV viewing.

(VCR Record) Button - Press to start a

VCR recording of a TV program.

CC Button - Press to activate the Closed

Captioning options. Repeatedly press the

CC button with scroll the options available on the TV screen.

VOL

POWER button - Press the Power button to turn the TV on or off.

FROWNIE Button - Allows you to delete stored channels within the “Quadra Surf” lists for the colored buttons.

AUTO PICTURE Button - Press repeatedly to choose from 4 different factory predefined picture settings. Choose from

Personal (how you set the Picture Menu adjustment controls), Movies (when watching movies), Sports (for any sporting event), or Weak Signal (used when the signal being received is not the best).

STATUS/EXIT Button - Press to display the current channel number. If the onscreen menu is displayed, press the

Status/Exit button will remove it from the

TV’s screen.

CURSOR © , §§ , ©© , or n Buttons -

Press to navigate, select and adjust controls within the on-screen menu after the Menu button is pressed. These buttons also can be used with a VCR and when the

TV/VCR/ACC Switch is in the VCR position. Press the to PLAY © , REWIND §§ ,

FAST FORWARD ©© , or STOP ■ the viewing of a prerecorded video tape.

CH(annel) + or – Buttons - Press to select channels in ascending or descending order.

SLEEP Button - Press the Sleep button to set the TV to automatically turn itself off after a set period of time. Press repeatedly to select 15, 30, 45, 60, 90, 120, or 180 minutes.

PAUSE Button - Press to pause the viewing of a prerecorded video. The picture will freeze on the screen until the Play or Pause buttons are pressed again.

NUMBERED (0-9) Buttons - Press the numbered buttons to select TV channels or to enter certain values within the on-screen menu. For single channel entries, press the numbered button for the channel you desire. the TV will pause for a second or two before changing to the chosen channel.

A/CH Button - (Alternate Channel) Press to toggle between the last view channel and the channel presently being viewed.

2

VOL

1

S

ETTING

U

P

Y

OUR

T

ELEVISION

F

OR THE

F

IRST

T

IME

M

ENU

F eatures for your television can be adjusted from within a MENU shown on the

TV’s screen. A MENU is nothing more than an 0nscreen list of features. Some of the features have submenus but each MENU item can be adjusted or activated

(deactivated) by viewing the screen and simply pressing the proper button.

Press the MENU but-

ton on the remote or the

Install/Menu buttons (Volume

+, –) on the TV simultaneously to show the on-screen menu.

Press the CURSOR UP

© or DOWN buttons on the remote (or the Volume +, – buttons on the TV) to pick any of the on-screen menu features.

Picture Features Menu

Menu

Picture

Sound

Features

Install

Brightness

Color

Picture

Sharpness

Tint

More...

Sound Features Menu

Main

Picture

Sound

Features

Install

Treble

Bass

Balance

AVL

Incr. Surr

More...

Press the CURSOR

RIGHT ©© or LEFT §§

buttons on the remote (or

Channel or buttons on the TV) to adjust any highlighted on-screen feature.

Features Menu

Press the

STATUS/EXIT button on the remote to clear the menu from the screen after an adjustment.

You can also just wait a few seconds after you finish the feature adjustment and the menu will disappear from the screen automatically.

Install Features Menu

Menu

Picture

Sound

Features

Install

Timer

AutoLock

Menu

Picture

Sound

Features

Install

Language

Tuner Mode

Auto Program

Channel Edit

3

2 S

MART

H

ELP

If you pass the feature you want, press the MENU button on the remote to move back through the MENU one step at a time.

The MENU has a list of features, some with sub-menus. All the onscreen menu feature can b e adjusted or activated (deactivated).

The on-screen menu will time out and disappear from the screen when you finish, or you can press the STATUS/EXIT button to clear the menu from the screen.

L

ANGUAGE

F or our Spanish speaking

TV owners an on-screen

LANGUAGE option is present. With the LANGUAGE control you can set the TV’s on-screen menu to be shown in either English or Spanish.

1

2

4

6

Press the MENU but-

ton on the remote to show the on-screen menu.

Press the CURSOR UP

© or DOWN buttons to scroll through the on-screen menu until the word INSTALL is highlighted.

Press the CURSOR

RIGHT ©© button to display the INSTALL menu features.

Press CURSOR UP © or

DOWN buttons to scroll the

Install features until the word

LANGUAGE is highlighted.

Press the CURSOR

RIGHT ©© button repeat-

edly to select ENGLISH or

ESPANOL (Spanish

When finished, press

the STATUS/EXIT button to remove the menu from the

TV’s screen.

Menu

Picture

Sound

Features

Install

Brightness

Color

Picture

Sharpness

Tint

More...

Menu

Picture

Sound

Features

Install

Language

Tuner Mode

Auto Program

Channel Edit

Install

Language

Tuner Mode

Auto Program

Channel Edit

English

Instaler

Idioma

Sintonia

Auto Programa

Editar Canal

Español

VOL

4

2

3

5

S

MART

H

ELP

Remember, the Language control only makes the TV’s onscreen MENU items appear in English or Spanish text.

It does not change the other on-screen text features such as Closed Caption

(CC) TV shows.

T

UNER

M

ODE he TUNER MODE conT trol allows you to change the TV’s signal input to either

ANTENNA, CABLE or AUTO mode. It’s important for the

TV to know what type of signal to look for. (From a

Cable TV signal or a normal

Antenna signal.) In the

AUTO mode, when the AUTO

PROGRAM feature is activated, the TV will automatically choose the correct mode.

Press the MENU but-

ton on the remote to show the on-screen menu

Menu

Picture

Sound

Features

Install

Brightness

Color

Picture

Sharpness

Tint

More...

Press the CURSOR UP

© or DOWN buttons to scroll through the on-screen menu until the word INSTALL is highlighted.

Press the CURSOR

RIGHT ©© button to display the INSTALL menu features.

Press CURSOR UP © or

DOWN buttons to scroll the

Install features until the words

TUNER MODE is highlighted

Press the CURSOR

RIGHT

© © button to select either ANTENNA, CABLE, or AUTO mode.

When finished, press

the STATUS/EXIT button to remove the on-screen menu from the TV’s screen.

Menu

Picture

Sound

Features

Install

Language

Tuner Mode

Auto Program

Channel Edit

Install

Language

Tuner Mode

Auto Program

Channel Edit

English

Antenna

Install

Language

Tuner Mode

Auto Program

Channel Edit

English

Cable

Install

Language

Tuner Mode

Auto Program

Channel Edit

English

Auto

1 2

4

6

VOL

4

2

3

5

S

MART

H

ELP

When CABLE is selected, channels 1-125 are available. When ANTENNA is selected, channels

2-69 are available.

When AUTO is selected, the TV will automatically set itself to the correct mode based on the type of signal it detects when the AUTO PROGRAM feature is activated.

3

S

ETTING

U

P

Y

OUR

T

ELEVISION

F

OR THE

F

IRST

T

IME

A

UTO

P

ROGRAM

Y our TV can automatically set itself for local area

(or Cable TV) channels. This makes it easy for you to select only the TV stations in your area when the CHAN-

NEL (+), (–) buttons are pressed.

Note: Make sure the antenna or cable signal connection has been completed before

AUTO PROGRAM is activated.

Press the MENU but-

ton on the remote to show the on-screen menu.

Press the CURSOR UP

© or DOWN buttons to scroll through the on-screen menu until the word INSTALL is highlighted.

Menu

Picture

Sound

Features

Install

Brightness

Color

Picture

Sharpness

Tint

More...

Press the CURSOR

RIGHT ©© button to display the INSTALL menu features.

Press CURSOR UP © or

DOWN buttons to scroll the

Install features until the words

AUTO PROGRAM are highlighted.

Menu

Picture

Sound

Features

Install

Language

Tuner Mode

Auto Program

Channel Edit

Press the CURSOR

RIGHT ©© button to start the Auto Program scanning of channels. Auto Programming will store all available channels in the TV’s memory then tune to the lowest available channel when done.

Install

Language

Tuner Mode

Auto Program

Channel Edit

2

4

1

6

When finished, press the

STATUS/EXIT button to remove the menu from the

TV’s screen.

Auto Program will scan for all available channels within the

Antenna/Cable signal. When finished, the TV will go back to the INSTALL menu.

Auto Program

Channel 12

VOL

4

2

3

5

S

MART

H

ELP

Try it out. Press the CHANNEL (+), (–) buttons and see which channels have been added to the TV’s memory.

If you want to delete any unwanted channels from the

TV’s memory, refer to the section on adding and removing channels (Channel Edit) on the next page.

C

HANNEL

E

DIT

C hannel Edit makes it easy for you to ADD or

DELETE channels from the list of channels stored in the

TV’s memory.

1

Press the MENU but-

ton on the remote to show the on-screen menu.

Press the CURSOR UP

© or DOWN buttons to scroll through the on-screen menu until the word INSTALL is highlighted.

Press the CURSOR UP

© or DOWN buttons to scroll the Install features until the words CHANNEL EDIT are highlighted.

Press the CURSOR

RIGHT ©© button to display the CHANNEL EDIT options.

Press the CURSOR

RIGHT ©© button to display the INSTALL menu features.

With the CHANNEL

EDIT options displayed, and

PROGRAM NO. highlighted; enter the channel number

(with the NUMBERED or the

CH + or – buttons) you wish to add (Skipped OFF), or delete (Skipped ON) from the

TV’s memory.

Now use the CURSOR

RIGHT ©© button to toggle between ON or OFF.

If ON is selected the channel is skipped when scrolling channels with the CH + or – buttons. If OFF is selected the channel is not skipped when scrolling channels with the CH

+ or – buttons.

Scroll down (using the

CURSOR DOWN ■ button) to highlight the word

SKIPPED.

When finished, press

the STATUS/EXIT button to remove the menu from the

TV’s screen.

Menu

Picture

Sound

Features

Install

Brightness

Color

Picture

Sharpness

Tint

More...

Menu

Picture

Sound

Features

Install

Language

Tuner Mode

Auto Program

Channel Edit

Install

Language

Tuner Mode

Auto Program

Channel Edit

Program No.

Skipped

Channel Edit

Program No.

Skipped

12

2

4

9

VOL

7

4

2

6

3

5

8

Channel Edit

Program No.

Skipped On

Channel Edit

Program No.

Skipped Off

4

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

advertisement