Advertisement
Advertisement
C
ONTENTS
Important Notice/Warning............................................................1
Hooking up the TV ..................................................................1–2
Operating the Television and Remote Control ........................2–4
Using the Installation Features ................................................4–6
Using the Picture-in-Picture (PIP) Feature ..................................7
Adjusting the Manual Converge Controls....................................8
As an Energy Star®
Partner, Philips Consumer
Electronics has determined this product meets the Energy
Star® guidelines for energy efficiency. Energy Star® is a
U.S. registered mark. Using products with the Energy
Star® label can save energy.
Saving energy reduces air pollution and lowers utility bills.
IMPORTANT
This owner's manual is used with several different television models.
Not all features (and drawings) discussed in this manual will necessarily match those found with your television set. This is normal and does not require that you contact your dealer or request service.
WARNING: TO PREVENT FIRE OR SHOCK HAZARD DO NOT
EXPOSE THIS UNIT TO RAIN OR EXCESSIVE MOISTURE.
H
OOKING UP THE
TV
B
EST
V
IEWING
T he major benefit of this projection television is its large viewing screen. To see this large screen at its best, test various locations in the room to find the optimal spot for viewing.
NOTE: Be sure to allow a free flow of air to and from the perforated back cover of the set.
C
ABLE
TV
T his connection WILL supply Stereo sound to the TV.
1 Connect the cable TV signal to the ANTENNA IN 75
Ω jack on the back of the TV.
NOTE: Refer to the sections on TUNER MODE and AUTO
PROGRAM on pages 4 and 5 of this guide. Set TUNER
MODE to the CABLE option. Run AUTO PROGRAM to store all available cable channels in the TV’s memory.
To avoid cabinet warping, cabinet color changes, and increased chance of set failure, do not place the TV where temperatures can become excessively hot—for example, in direct sunlight or near a heating appliance.
ANTENNA IN 75 Ω
INPUT-AV 1
Y
OUTPUT
VIDEO
S-VIDEO
L
L
AUDIO
R
Pb
Pr
INPUT-AV 2
VIDEO
S-VIDEO
L
L
AUDIO
R
DVI
HD INPUT-AV 5
HD INPUT-AV 4
G/Y
R/Pr
B/Pb
V
SYNC
AUDIO
H
L
R
L
AUDIO
R
Magnetic fields, such as those of external speakers, may cause the picture to distort if the speakers are placed too close to the television. Move the magnetic field source away from the TV until there is no picture distortion.
Cable TV
Signal 1
Back of TV
VIDEO
S-VIDEO
L
L
AUDIO
R
INPUT-AV 1
Pb
Pr
Y
OUTPUT INPUT-AV 2
VIDEO
S-VIDEO
L
L
AUDIO
R
DVI
HD INPUT-AV 5
HD INPUT-AV 4
G/Y
R/Pr
B/Pb
V
L
SYNC
AUDIO
H
R
L
AUDIO
R
C
ABLE
B
OX WITH
RF IN/OUT
T his is for example purposes only. The back of your cable box may be labeled somewhat differently.
This connection WILL NOT supply stereo sound to the TV.
1
2
Connect the cable TV signal to the CABLE IN jack on the back of the cable box.
Connect a coaxial cable (not supplied) to the TO TV jack on the back of the cable box and to the ANTENNA
IN 75 Ω jack on the back of the TV.
3 Be sure to set the Output Channel switch on the back of the cable box to CH 3 or 4, then tune the cable box on the TV to the corresponding channel. Once tuned, change channels at the cable box, not the TV.
NOTE: Refer to the sections on TUNER MODE and AUTO
PROGRAM on pages 4 and 5 of this guide. Set TUNER
MODE to the CABLE option. Run AUTO PROGRAM to store all available cable channels in the TV’s memory.
C
ABLE
B
OX WITH
A/V O
UTPUTS
T his is for example purposes only. The back of your cable box may be labeled somewhat differently.
This connection MIGHT supply stereo sound to the TV. Check with your cable TV company.
1
2
3
4
5
Connect the incoming cable TV signal to a signal splitter.
Connect a coaxial cable to a connector on the signal splitter and to the ANTENNA IN 75
Ω jack on the back of the
TV.
Connect a coaxial cable to a connector on the signal split- ter and to the CABLE IN jack on the back of the cable box.
Connect A/V cables to the VIDEO and AUDIO L and R outputs on the back of the cable box and to the AV2
VIDEO and corresponding AUDIO L and R jacks on the back of the TV.
To view programs from your cable box, plug in the TV, turn it on, and then press the AV button on the remote control as many times as necessary to select the AV2 input source.
1
Signal
Splitter
Cable TV
Signal
Back of Cable Box
(example only)
CABLE
IN
1 3
TO TV
OUTPUT
CH
3 4
Cable TV Signal
2
Back of TV
ANTENNA IN 75
Ω
INPUT-AV 1
Y
OUTPUT
VIDEO
S-VIDEO
L
L
AUDIO
R
Pb
Pr
INPUT-AV 2
VIDEO
S-VIDEO
L
L
AUDIO
R
DVI
HD INPUT-AV 5
HD INPUT-AV 4
G/Y
R/Pr
B/Pb
V
SYNC
AUDIO
H
L
R
L
AUDIO
R
CABLE
IN
TO
TV
OUTPUT
CH
3 4
3
VIDEO
OUT
L
AUDIO
OUT
R
Back of Cable Box
(example only)
ANTENNA IN 75
Ω
2 Back of TV
INPUT-AV 1
Y
OUTPUT
VIDEO
S-VIDEO
L
L
AUDIO
R
Pb
Pr
INPUT-AV 2
VIDEO
S-VIDEO
L
L
AUDIO
R
DVI
B/Pb
R/Pr
G/Y
HD INPUT-AV 5
HD INPUT-AV 4
4
V
SYNC
AUDIO
H
L
R
L
AUDIO
R
TV
SWAP
DN
PIP CH
VCR ACC
ACTIVE
CONTROL FREEZE
UP
SOUND
PICTURE
STATUS/
EXIT
MENU/
SELECT
MUTE
VOL CH
POSITION
1
4
7
TV/VCR
A/CH
8
0
2
5
3
6
9
SURF
AV
SURF
REC •
SAP
FORMAT
PIP ON/OFF
SLEEP
DOLBY V PROG.LIST
5
ITR/
RECORD
HOME
VIDEO
HOME
MOVIES
PERSONAL
PIP
3135 035 21372
A
NTENNA
TV
T his connection WILL supply stereo sound to the TV.
1 Connect the antenna signal to the ANTENNA IN 75
Ω jack on the back of the TV.
NOTE: Refer to the sections on TUNER MODE and AUTO
PROGRAM on pages 4 and 5 of this guide. Set TUNER
MODE to the ANTENNA option. Run AUTO PROGRAM to store all available cable channels in the TV’s memory.
H
OOKING UP THE
TV
Antenna Signal
ANTENNA IN 75 Ω
1
Back of TV
INPUT-AV 1
Y
OUTPUT
VIDEO
S-VIDEO
L
L
AUDIO
R
Pb
Pr
INPUT-AV 2
VIDEO
S-VIDEO
L
L
AUDIO
R
DVI
HD INPUT-AV 5
HD INPUT-AV 4
G/Y
R/Pr
B/Pb
V
L
SYNC
AUDIO
H
R
L
AUDIO
R
POWER
TV
SWAP
SOUND
DN
PIP CH
VCR ACC
ACTIVE
CONTROL FREEZE
UP
PICTURE
STATUS/
EXIT
MENU/
SELECT
O
PERATING THE
T
ELEVISION AND
R
EMOTE
C
ONTROL
T
ELEVISION
U
SING THE
TV B
UTTONS
S hould your remote control be lost or broken, you can still change some of the basic picture and sound settings with the buttons on the TV. Follow the steps below to familiarize yourself with the functions of the TV buttons.
1
2
Press POWER/STANDBY to turn the TV on (or off).
Allow about 10 seconds for the TV to power on.
Press the VOL(ume) + or – buttons to decrease or increase the sound level.
Press the VOLUME + and – buttons simultaneously to display the on-screen menu. After the menu appears, use these buttons to enter submenus and make selections or adjustments. (Use the CHANNEL buttons to move up and down in the menu or submenus.) Press both VOLUME buttons simultaneously to back out of the on-screen menus.
3
4
Press SOURCE SELECT to choose from among the sig-
nal inputs you have connected to the TV.
Press the CHANNEL buttons to select TV channels.
VOLUME
Remote Sensor
Window
MENU
?
CHANNEL
> SOURCE
SELECT
VOLUME
A
MENU
?
CHANNEL
> SOURCE
SELECT
Power Standby
Button
H
ELPFUL
H
INT
You can press any of the buttons on the front of the TV to turn the TV on, but you must press the Power/Standby button to turn the set off.
R
EMOTE
C
ONTROL
I
NSTALLING
B
ATTERIES
T o load the supplied batteries into the remote, follow these steps.
1
2
Gently press and hold the indentation on the back of the remote and slide the battery cover off the remote.
Place the two “AA” size batteries in the remote’s bat-
tery case. Ensure that the (+) and (–) ends of the batteries line up correctly with the (+) and (–) inside the case.
3 Slide the battery cover back into place.
P
OINTING THE
R
EMOTE
Press the TV mode button on the remote to ensure that the
remote sends its commands to the TV. When operating the remote control, point the remote toward the remote sensor window on the TV.
POWER
VCR TV
SWAP
VCR
PIP CH
ACC
ACTIVE
CONTROL
FREEZE
PICTURE
SOUND
MENU/
SELECT
TV MODE
MUTE
CH
Button
VOL
ACC
TV/VCR
A/CH
POSITION
PIP
B
ATTERY
U
SAGE
CAUTION
To prevent battery leakage that may result in injury to you or damage to the remote control:
• Install ALL batteries correctly, + and –, as marked on the unit.
• Do not mix batteries (OLD and NEW or CARBON and ALKALINE, etc.)
• Remove batteries when the remote control is not used for a long time.
Do not take apart, heat, or put batteries in fire.
H ELPFUL H INTS
• Be sure to point the remote toward the sensor window on the TV or accessory device you wish to operate.
• Press the correct mode button for the device: TV, VCR, ACC (for accessories other than VCRs).
• Be within about 30 feet (10 meters) of the TV or accessory device you wish to operate.
• Avoid dropping the remote on hard surfaces.
• Do not use harsh chemicals to clean the remote. Use only a soft, lightly moistened cloth.
c
HECK
I
T
O
UT
You can set up your TV remote control to work with accessory devices such as VCRs, DVD players, and cable converter boxes.
See pages 18–23 in the Directions for Use manual.
2
O
PERATING THE
T
ELEVISION AND
R
EMOTE
C
ONTROL
R
EMOTE
C
ONTROL
VCR control buttons
Press to pause, rewind, stop, play, or fast forward a videotape.
TV • VCR • ACC
(Mode buttons) Press to send remote signals to either the
TV, VCR, or other accessory devices such as cable TV converters, satellite receivers, DVDs, or laser disc players. (You may need to program the remote to work accessory devices.
See pages 18–23 in the Directions for Use manual that came with your TV.)
PIP buttons: SWAP, PIP CH DN/UP, FREEZE
Press to operate the Picture-in-Picture (PIP) features. See page 7 in this publication for more information on using these buttons.
Sound
Press to select an AutoSound™ control. (See page 25 in the
Directions for Use manual.) Choose from three factory-set controls—Voice, Music, and Theatre—and a Personal control that you set according to your own preferences through the on-screen Sound menu. The three factory-set controls will tailor the TV sound so as to enhance the type of program you are watching.
Status/Exit
Pressing the button once shows the current channel number, name (if set), time (if set), Sleep Timer setting, and sound setting (stereo, mono, SAP, or mute). Pressing the button twice shows the current AutoLock™ settings. Pressing the button once when an on-screen display is showing removes the on-screen display.
Cursor Ring
Up/Down: allows you to select the next or previous item in the menu. Left/Right: allows you to access the submenus and adjust the settings. When no on-screen displays or menus are present, use the Cursor Ring Left/Right to select a picture format for a video source connected to the
ANTENNA, AV1, CVI, AV2, or AV3 (side panel inputs) on the TV.
Volume +/–
Press to adjust the TV sound level.
Number Buttons
Press to select TV channels. When selecting single-digit channels, press the number of the desired channel. The TV will pause for a few seconds and then tune to the selected channel.
TV/VCR
Press while in VCR mode to view the playback of a videotape. Press again to return to TV mode.
A/CH
Press to alternate between the currently viewed channel and the previously viewed channel.
Rec
¶
Press this button simultaneously with the 3 button when in
VCR mode to record.
SAP
Press to select between main sound and SAP (Second Audio
Program) when you tune to a program offering SAP. (See page 37 in the Directions for Use manual.)
AV
Press repeatedly to select the different signal sources connected to the TV: TV, AV1, CVI, AV2, AV3 (side jack panel), AV4 and AV5. (See page 24 in the Directions for Use manual.)
Clock
Press to access the on-screen Timer menu, where you can set the time for the TV’s clock or set the TV’s Timer features, such as channel switchover, power on set, and power off set. (See page 6 in this publication for setting the time manually. See pages 39–43 in the Directions for Use manual for information on using the TV’s Timer feature.)
Position
Press to move the PIP picture to any of the four corners of the screen.
Back Light button
Press to light the buttons on the remote control.
PIP
Press to turn PIP (picture-in-picture) on or off or control the size of the PIP window. (See page 7 in this publication for more information on PIP.)
STATUS/
EXIT
VOL
1
4
7
TV/VCR
A/CH
2
5
8
0
3
6
9
ITR/
RECORD
HOME
VIDEO
HOME
MOVIES
PERSONAL
POSITION
MUTE
POWER
TV
SWAP
DN
PIP CH
VCR ACC
ACTIVE
CONTROL FREEZE
UP
SOUND PICTURE
PIP
MENU/
SELECT
SURF
AV
SURF
REC •
SAP
FORMAT
PIP ON/OFF
SLEEP
DOLBY V PROG.LIST
CH
POWER
SWAP
TV
DN
VCR
PIP CH
UP
ACC
ACTIVE
CONTROL FREEZE
SOUND PICTURE
STATUS/
EXIT
Power
Press to turn the TV on or off.
Active Control™
Measures and corrects all incoming signals to provide the best picture-quality settings. (See page 56 in the Directions
for Use manual.) Press to turn Active Control™ on or off.
When Active Control™ is on, it automatically and continuously controls Sharpness and Noise Reduction settings .
Picture
Press to select an AutoPicture™ control. Choose from four factory-set controls—Movies, Sports, Weak Signal, and
Multimedia—and a PERSONAL control that you set according to your own preferences through the on-screen
Picture menu. (See page 26 in the Directions for Use manual.) The four factory-set controls will enhance the TV picture according to the particular type of program you are watching. It may also be used to enhance pictures with weak signals.
Menu/Select
Press to display the on-screen menu. Press to return to a higher menu level.
Channel +/–
Press to select channels in ascending or descending order or cycle through the signal inputs.
Mute
Press to turn the TV sound off. To restore the sound to its previous level, press the button again. (See pages 17 and 53 in the Directions for Use manual.)
Surf
Press to select previously entered channels. With the TV’s
AutoSurf™ control, you can place up to 10 favorite channels or sources in memory. Then by pressing the Surf button, you can quickly view the selected channels. (See page
27 in the Directions for Use manual that came with the TV to learn how to select a series of your favorite channels using the Surf button.)
Format
Press to select a picture-format mode for a video source connected to the ANTENNA, AV1, CVI, AV2, or AV3 (side panel) inputs. Each press of the button selects a different mode—4:3, EXPAND 4:3, PANORAMA, WIDE SCREEN, or AUTO. Control the picture format of a video source connected to the HD inputs (AV4 or AV5) with the HD set-top box or progressive-scan-capable DVD player providing the video source.
Sleep
Press to set the TV to automatically turn itself off after a period of time. Choose 15, 30, 45, 60, 90, 120, 180, or 240 minutes before the TV will automatically turn off. (See page
29 in the Directions for Use manual.)
Program List
Press to display a list of channel numbers and their names.
(See the “Tuner Mode,” “Auto Program,” “Channel Edit,” and “Name” sections on pages 4–6 in this guide for setup.)
Each channel will appear as a selectable menu item. The current channel will be highlighted as default. Five channels will be listed on screen at one time. Press the Cursor Ring up or down to scroll the list and and highlight a channel.
Press the Cursor Ring right to tune to the highlighted channel. Channels marked “Skipped” in the Channel Edit control will not appear in the list. Each channel that is being blocked by AutoLock™ will appear with a padlock icon to indicate that the channel is not viewable. (See page 28 in the
Directions for Use manual.)
Dolby V
Press to select various factory surround sound listening modes.
Dolby* Virtual (Virtual Dolby Surround) (with Virtual
Dolby Surround signals)
Dolby Virtual uses two speakers to simulate the surround effect produced by a multichannel system.
Incredible Surround™
• In Stereo sound mode—when Incredible Surround™ is turned on—it seems as though the loudspeakers are spread farther apart from each another.
• In Mono sound mode—when Incredible Surround™ is turned on—enables you to hear a spatial sound effect.
(See page 35 in the Directions for Use manual.)
*Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories.
Active Control, AutoPicture, AutoSound, AutoSurf, and Incredible Surround are trademarks of Philips Consumer Electronics. Copyright 2003 Philips Consumer Electronics. All rights reserved.
3
POWER
TV
SWAP
SOUND
DN
PIP CH
UP
VCR ACC
ACTIVE
CONTROL FREEZE
PICTURE
STATUS/
EXIT
MENU/
SELECT
O
PERATING THE
T
ELEVISION AND
R
EMOTE
C
ONTROL
R
EMOTE
C
ONTROL
A
DJUSTING OR
S
ETTING
M
ENU
O
PTIONS
A menu is simply a list of options. You can adjust or set your
TV’s on-screen menu options by pressing buttons on the remote control. The following steps will familiarize you with how to use the remote control with the on-screen menu.
1
2
3
Press the TV mode button to ensure that the remote control is in TV mode.
Press the MENU/SELECT button to bring the menu to
the screen. Then, as necessary, press the CURSOR RING
DOWN or UP to highlight a menu option. Press the CUR-
SOR RING RIGHT to enter the submenu for the option.
Within the submenu, press the CURSOR RING DOWN
or UP to highlight an option.
Based on the submenu you are in, you can press the CUR-
SOR RING RIGHT or LEFT to make an adjustment, select a setting, or enter a list or another submenu.
You can return to the submenu from a list by pressing the
CURSOR RING LEFT.
To go from a submenu to the previous menu, highlight the option at the top of the screen and press the CURSOR
RING UP. You can also press MENU/SELECT to return to the previous menu.
Press STATUS/EXIT to exit the menu.
1
PICTURE
SOUND
FEATURES
INSTALL
STATUS/
EXIT
VOL
3
MENU
8
0
2
5
TREBLE
BASS
BALANCE
AVL
INCR .
POWER
TV
SWAP
SOUND
DN
PIP CH
VCR
ACTIVE
CONTROL
ACC
FREEZE
UP
PICTURE
7
TV/VCR
A/CH
1
4
POSITION
MUTE
PIP
3
6
9
MENU/
SELECT
SURF
CH 2
Go from one submenu to another and make settings or adjustments.
SOUND SUBMENU
SOUND
TREBLE
BASS
BALANCE
AVL
INCR . SURROUND
SOUND
BALANCE
AVL
INCR .
HEADPHONE
STEREO MONO
STEREO STEREO
INSTALL SUBMENU
INSTALL
LANGUAGE
TUNER MODE
AUTO PROGRAM
CHANNEL EDIT
AutoChron
FEATURES
TIMER
AutoLock
PIP
CLOSED CAP
FORMAT
OR
2
3
AV3
AV4
1
TIME
START TIME
STOP TIME
CHANNEL
ACTIVATE
30
FEATURES SUBMENU
Make adjustments or selections within a submenu.
Also from a Submenu, enter a list to make selections.
INSTALL
LANGUAGE
TUNER MODE
AUTO PROGRAM
CHANNEL EDIT
AutoChron
AV3
AV4
1
2
3
TIMER SUBMENU
FEATURES
TIMER
TIME 8:06 PM
START TIME
STOP TIME
CHANNEL
ACTIVATE
H
ELPFUL
H
INTS
• If you don’t press any remote buttons, the menu will automatically disappear after about 20 seconds. To bring the menu back, press
MENU/SELECT.
• Sometimes not all the menu items are visible on the screen. If more items exist in the menu, a cursor arrow will appear.
Also, a bullet will appear for each remaining item, up to a maximum of three. This will help you determine how many items are left in the menu. Keep pressing the CUR-
SOR RING
DOWN until you display all items.
• Should your remote become lost or otherwise unavailable for use, you can use the buttons on the front of the TV to access the onscreen menu and make adjustments or settings. See page 2.
T
PICTURE
SOUND
FEATURES
INSTALL
LANGUAGE
TUNER MODE
AUTO PROGRAM
CHANNEL EDIT
AutoChron
L
ANGUAGE
U
SING THE
I
NSTALLATION
F
EATURES he menu LANGUAGE control enables you to set the TV’s onscreen menu and on-screen displays to be shown in English,
French, or Spanish. Follow the steps in this section to set the control.
1
2
3
4
5
Press the MENU/SELECT button. The on-screen menu appears.
Press the CURSOR RING DOWN repeatedly until
INSTALL is highlighted. Then press the CURSOR RING
RIGHT to enter the INSTALL submenu.
Press the CURSOR RING RIGHT again to highlight the menu LANGUAGE options list.
Press the CURSOR RING DOWN or UP to select your menu language.
Instantaneously, the on-screen displays appear in the language that you choose.
Press the STATUS/EXIT button to exit the menus.
PICTURE
SOUND
FEATURES
INSTALL
LANGUAGE
TUNER MODE
AUTO PROGRAM
CHANNEL EDIT
AutoChron
INSTALL
LANGUAGE
TUNER MODE
AUTO PROGRAM
CHANNEL EDIT
AutoChron
ENGLISH
FRANCAIS
ESPAÑOL
5
STATUS/
EXIT
1
4
MUTE
2
5
POWER
SOUND
TV
SWAP
DN
PIP CH
VCR
UP
ACC
ACTIVE
CONTROL FREEZE
PICTURE
3
MENU/
SELECT
3
6
CH
1
INSTALL
LANGUAGE
TUNER MODE
AUTO PROGRAM
CHANNEL EDIT
AutoChron
ENGLISH
FRANCAIS
OR
French
INSTALLATION
LANGUE
TUNER MODE
PROGRAM.AUTO
CHANGER CANAL
AutoChron
FRANCAIS
ESPAÑOL
ENGLISH
Make your selection and instantaneously the onscreen display appears in the language you chose.
H ELPFUL H INT
The LANGUAGE control makes only the
TV’s on-screen menu items appear in English,
French, or Spanish text.
The control does not change the language of
Closed Captioning (CC) text that may be included with programs.
Spanish
OR
INSTALAR
IDIOMA
SINTONIZADOR
AUTO PROG.
EDITAR CANAL
AutoChron
ESPAÑOL
ENGLISH
FRANCAIS
T
UNER
M
ODE
S et the TUNER MODE control according to the type of signal you have connected to the TV—ANTENNA or CABLE. If you select AUTO, the
TV will automatically detect the type of signal you have connected.
1
2
3
4
Press the MENU/SELECT button. The on-screen menu appears. Press the CURSOR RING DOWN repeatedly until
INSTALL is highlighted.
Press the CURSOR RING RIGHT to enter the
INSTALL submenu. Then press the CURSOR RING
DOWN once to highlight TUNER MODE.
Press the CURSOR RING RIGHT to highlight the
TUNER MODE options list.
Press the CURSOR RING DOWN or UP repeatedly until you select the option that matches your signal con-
nection, CABLE or ANTENNA. If you want the TV to determine the type of signal, select AUTO. (You have selected an option when the dot and triangle are next to the option.)
Press the STATUS/EXIT button to exit the menu.
5
6 Proceed to the section on “Auto Program.”
INSTALL
LANGUAGE
TUNER MODE
AUTO PROGRAM
CHANNEL EDIT
AutoChron
CABLE
ANTENNA
AUTO
POWER
5
STATUS/
EXIT
SOUND
TV
SWAP
DN
PIP CH
VCR
UP
ACC
ACTIVE
CONTROL FREEZE
PICTURE
2,3
MENU/
SELECT
VOL
4
1
4
7
MUTE
2
5
8
3
6
9
CH
1
4
INSTALL
LANGUAGE
TUNER MODE
AUTO PROGRAM
CHANNEL EDIT
AutoChron
CABLE
ANTENNA
AUTO
H ELPFUL H INT
If you select the Tuner
Mode option that matches your signal source rather than
AUTO, the time required for AUTO
PROGRAM to store channels to the TV’s memory can be reduced.
PICTURE
SOUND
FEATURES
INSTALL
LANGUAGE
TUNER MODE
AUTO PROGRAM
CHANNEL EDIT
AutoChron
3
4
1
2
U
SING THE
I
NSTALLATION
F
EATURES
A
UTO
P
ROGRAM
T he AUTO PROGRAM feature will scan for channels with active broadcast signals and store those channels in the TV’s memory. It will tune up to 69 channels for antenna, and up to 125 channels for cable. After you run AUTO PROGRAM, you can use the CH(annel) +/– buttons to quickly and easily select stations.
You can also press the PROG. LIST (Program List) button on your remote to see a list of the channels.
INSTALL
LANGUAGE
TUNER MODE
AUTO PROGRAM
CHANNEL EDIT
AutoChron
SEARCH
INSTALL
LANGUAGE
TUNER MODE
AUTO PROGRAM
CHANNEL EDIT
AutoChron
CABLE
PLEASE WAIT
CHANNEL 12
POWER
Press the MENU/SELECT button. The on-screen menu appears. Then press the CURSOR RING DOWN repeatedly until INSTALL is highlighted.
Press the CURSOR RING RIGHT to enter the INSTALL
submenu. Then press the CURSOR RING DOWN repeatedly until AUTO PROGRAM is highlighted.
Press the CURSOR RING RIGHT to begin the automatic
search for channels. The progress of autoprogramming is displayed.
When the programming is done, press the STATUS EXIT button to exit the menu.
4
STATUS/
EXIT
SOUND
TV
SWAP
DN
PIP CH
VCR
UP
ACC
ACTIVE
CONTROL FREEZE
PICTURE
2,3
MENU/
SELECT
VOL
1 2
MUTE
3
CH
1 c
HECK I T O UT
After you’ve run AUTO
PROGRAM, check the results. Press the
CH(annel) +/– buttons on your remote to cycle through your available channels. Or press the
PROG. LIST button to show a list of the channels and tune to them. See page 28 in the Directions
for Use manual for more on Program List.
H
ELPFUL
H
INTS
• Philips strongly recommends that you run Auto
Program. Otherwise, the
TV may not tune the channels properly, resulting in improper pictures.
• If you change signal sources—to a new cable company or from antenna to cable, for example—be sure that Tuner Mode is properly set for the new source. Then run Auto
Program again. This will ensure that the channels are correctly stored in the
TV’s memory.
• If you have made
AutoLock™ settings, remember that you must remove any channel blocks before Auto Program will work. (See pages 44–52 in the Directions for Use manual.)
C
HANNEL
E
DIT
his feature allows you to edit or skip channels from the channel T list that have bad or weak signals or channels you do not want to watch.
1
2
3
4
5
Press the MENU/SELECT button. The on-screen menu appears. Then press the CURSOR RING DOWN repeatedly until INSTALL is highlighted. Press the CURSOR RING right to enter the INSTALL submenu.
Press the CURSOR RING DOWN repeatedly until
CHANNEL EDIT is highlighted. Then press the CURSOR
RING RIGHT or LEFT to access the CHANNEL EDIT list.
Press the CURSOR RING UP or DOWN to scroll
through the list of channels. Or press the NUMBER buttons on your remote control to select a specific channel.
With the channel you want to edit selected, press the
CURSOR RING RIGHT to mark the channel as
SKIPPED. (Channels you mark SKIPPED will not appear when you use the CH[annel] +/– buttons to change channels while watching TV.)
When you want to add a channel that has been marked
SKIPPED, press the CURSOR RING UP or DOWN to highlight the channel. Then press the CURSOR RING RIGHT to remove the word SKIPPED.
Press the STATUS/EXIT button to exit the menu.
AutoChron™
A utoChron™ gives you the option of setting the time manually or automatically.
S
ETTING
T
IME
A
UTOMATICALLY
The steps in this section tell you how to set AutoChron™ to download the time from your PBS station to your TV. After successful setup, AutoChron™ will automatically maintain the correct time using your PBS station until you set the time manually.
3
4
5
1
2
6
7
8
Press the MENU/SELECT button. The on-screen menu appears. Then press the CURSOR RING DOWN repeatedly until INSTALL is highlighted.
Press the CURSOR RING RIGHT to enter the INSTALL
submenu. Then press the CURSOR RING DOWN repeatedly until AutoChron is highlighted.
Press the CURSOR RING RIGHT to enter the
AutoChron SET TIME area.
Press the CURSOR RING RIGHT again to select AUTO.
Within a few seconds, a menu containing the time-zone options appears.
If necessary, press the CURSOR RING UP or DOWN to
highlight your correct time zone. Then press the CURSOR
RING RIGHT. Within a few seconds, the option of Daylight
Savings Time appears on screen.
If the Daylight Savings Time option you want to select is not highlighted, press the CURSOR RING UP or DOWN
to highlight the option. Then press the CURSOR RING
RIGHT to activate your selection.
Press the number buttons on your remote to enter the channel number for your PBS station (02, 15, or 121, for
example). Wait until the TV completes its search. If the time was not found, you will need to locate the correct channel number for your PBS station and input that number.
Press the STATUS/EXIT button to exit the menu.
INSTALL
LANGUAGE
TUNER MODE
AUTO PROGRAM
CHANNEL EDIT
AutoChron
1
2
AV3
AV4
3
POWER
5
STATUS/
EXIT
3
TV
SWAP
DN
PIP CH
VCR
UP
ACC
ACTIVE
CONTROL FREEZE
PICTURE
4
SOUND
MENU/
SELECT
VOL
2
1
4
7
TV/VCR
A/CH
8
0
2
5
MUTE
3
6
9
SURF
CH
1
INSTALL
LANGUAGE
TUNER MODE
AUTO PROGRAM
CHANNEL EDIT
AutoChron
AV3
AV4
1
2 SKIPPED
3
H ELPFUL H INT
Channels that Auto
Program (see page 5) determined not to contain active broadcast signals are marked SKIPPED.
INSTALL
LANGUAGE
TUNER MODE
AUTO PROGRAM
CHANNEL EDIT
AutoChron
SET TIME
AUTO
MANUAL
INSTALL
LANGUAGE
TUNER MODE
AUTO PROGRAM
CHANNEL EDIT
AutoChron
SET TIME
AUTO
MANUAL
INSTALL
LANGUAGE
TUNER MODE
AUTO PROGRAM
CHANNEL EDIT
AutoChron
TIME ZONE?
CENTRAL
MOUNTAIN
PACIFIC
POWER
8
5, 6
TV
SWAP
DN
PIP CH
VCR
UP
ACTIVE
CONTROL
ACC
FREEZE
2,3,
4
PICTURE
SOUND
STATUS/
EXIT
MENU/
SELECT
INSTALL
LANGUAGE
TUNER MODE
AUTO PROGRAM
CHANNEL EDIT
AutoChron
DAYLIGHT
SAVING TIME?
YES
NO
VOL
1
4
7
TV/VCR
A/CH
POSITION
MUTE
8
0
2
5
PIP
3
6
9
SURF
CH
1
7
INSTALL
LANGUAGE
TUNER MODE
AUTO PROGRAM
CHANNEL EDIT
AutoChron
SEARCH FOR
TIME
PLEASE WAIT
15 PBS
The message shown to the right indicates that
AutoChron™ is not finding a PBS station at the channel you input.
Check the channel number for your PBS station.You will need to input the correct number for the time to be found.
INSTALL
LANGUAGE
TUNER MODE
AUTO PROGRAM
CHANNEL EDIT
AutoChron
SEARCH FOR
TIME
ENTER CHANNEL
02 PBS
INSTALL
LANGUAGE
TUNER MODE
AUTO PROGRAM
CHANNEL EDIT
AutoChron
SEARCH FOR
TIME
TIME FOUND
END: PRESS STATUS
11:15 AM
OR
INSTALL
LANGUAGE
TUNER MODE
AUTO PROGRAM
CHANNEL EDIT
AutoChron
SEARCH FOR
TIME
TIME NOT FOUND
RE-ENTER CHANNEL
15 PBS
5
PICTURE
SOUND
FEATURES
INSTALL
LANGUAGE
TUNER MODE
AUTO PROGRAM
CHANNEL EDIT
AutoChron
U
SING THE
I
NSTALLATION
F
EATURES
AutoChron™
S
ETTING
T
IME
M
ANUALLY
1
2
3
4
Follow steps 1–3 in the section “Setting Time
Automatically” on page 5, then press the CURSOR
RING DOWN to highlight MANUAL and CURSOR
RING RIGHT to enter the MANUAL time input area.
Use the number buttons on your remote control to
input the first digit for the time. You can also press the
CURSOR RING UP or DOWN to select a digit. Press the
CURSOR RING RIGHT to move to the next digit input slot and input the time.
If you should need to change a number you have input, you can cursor left or right to the digit input slot to make the correction.
After you have input the time, press the CURSOR
RING RIGHT to enter the AM/PM area. Then press the
CURSOR RING UP or DOWN to select AM or PM.
Press the STATUS/EXIT button to exit the menu.
INSTALL
LANGUAGE
TUNER MODE
AUTO PROGRAM
CHANNEL EDIT
AutoChron
SET TIME
AUTO
MANUAL
POWER
4
TV
SWAP
STATUS/
EXIT
SOUND 1
DN
PIP CH
VCR
UP
ACC
ACTIVE
CONTROL FREEZE
PICTURE
3
MENU/
SELECT
2
VOL
1
4
MUTE
2
5
3
6
CH
INSTALL
LANGUAGE
TUNER MODE
AUTO PROGRAM
CHANNEL EDIT
AutoChron
ENTER TIME
11:00 AM
7
TV/VCR
A/CH
8
0
9
SURF
AV
SURF
REC •
SAP
FORMAT
PIP ON/OFF
SLEEP
DOLBY V PROG.LIST
ITR/
RECORD
HOME
VIDEO
HOME
MOVIES
PERSONAL
CLOCK
Button
POSITION PIP
AutoChron is a trademark of Philips Consumer Electronics. Copyright
2003 Philips Consumer Electronics. All rights reserved.
H ELPFUL H INTS
• The CLOCK button
\ on your remote provides another way in which you can set the TV’s clock manually.
• After setting the clock, you will be able to access the time by pressing the
STATUS/EXIT button. Or you can view the time constantly in the upper right-hand corner of the screen by turning the DIS-
PLAY control on (see page 40 in the
Directions for Use manual).
N
AME
T he channel NAME feature allows you to list the “call” letters of your favorite stations beside their channel numbers when they appear on the screen. The TV has in memory a list of the 50 most popular channel names (NBC, ABC, or FOX, for example).
You also can enter a custom name (up to five characters).
3
4
1
2
Press the NUMBER buttons, the CH(annel) +/– buttons, or the AV button to select a TV channel or input source to which you want to assign or modify a name.
Press the MENU/SELECT button. The on-screen menu appears. Then press the CURSOR RING DOWN repeatedly until INSTALL is highlighted. Press the CURSOR RING
RIGHT to enter the INSTALL submenu.
Press the CURSOR RING DOWN repeatedly until the
NAME control is highlighted. Then press the CURSOR
RING RIGHT to highlight the NAME options area.
At this point you can choose between options of creating a personal name for the channel or selecting a preset one from a list.
To create your own personal name for the channel or change a personal name you created previously, press
the CURSOR RING RIGHT. Then press the CURSOR
RING UP or DOWN to select the first character of the name. You can input up to five characters for the name.
When finished, press the MENU/SELECT button.
Or
To choose from the list of preset names, press the CUR-
SOR RING UP or DOWN to highlight your choice for
the channel name. Press the CURSOR RING RIGHT to select the name. Then press the MENU/SELECT button.
5 Press the STATUS/EXIT button to exit the menu.
When you press the STATUS/EXIT button when no onscreen display is present or change to the channel you’ve named, the name will appear on screen next to the channel number or signal source name.
INSTALL
TUNER MODE
AUTO PROGRAM
CHANNEL EDIT
AutoChron
NAME PERSONAL
INSTALL
TUNER MODE
AUTO PROGRAM
CHANNEL EDIT
AutoChron
NAME PERSONAL
Create your own personal name for a channel.
POWER
5
4
TV
SWAP
DN
PIP CH
VCR
UP
ACC
ACTIVE
CONTROL FREEZE
PICTURE
4
SOUND
STATUS/
EXIT
MENU/
SELECT
MUTE
1
VOL
3
7
TV/VCR
A/CH
1
4
8
0
2
5
3
6
9
SURF
AV
SURF
REC •
SAP
FORMAT
PIP ON/OFF
SLEEP
DOLBY V PROG.LIST
CH
2
1
1
ITR/
RECORD
HOME
VIDEO
HOME
MOVIES
PERSONAL
POSITION PIP
WX-
WXY-
WXYZ-
WXYZ3
OR
Choose from a list of preset options.
INSTALL
TUNER MODE
AUTO PROGRAM
CHANNEL EDIT
AutoChron
NAME
USA
VH
WGN
WOR
WTHR
H ELPFUL H INTS
• The five PERSONAL name characters you can input may be letters, a dash, or the numbers 0 through 9.
• If you begin inputting a personal name or changing an existing one and decide you’d rather select a name from the preset list, press the MENU/
SELECT button. This will return you to the
INSTALL submenu, with NAME highlighted. Simply press the
CURSOR RING
RIGHT to highlight the NAME options area again and choose a preset name as explained in step 4 to the left.
6
U
SING THE
P
ICTURE
-
IN
-P
ICTURE
(PIP) F
EATURE icture-In-Picture (PIP) is the showing of two pictures on the P
TV screen at the same time—one main screen picture and one small picture, or PIP. Because your set has two tuners, you can enjoy all the benefits of PIP without using a VCR as a second tuner for your PIP picture. Tune to your favorite show on the main screen with tuner one while scanning other channels with tuner two in the PIP window. Also view the AV1, AV2, or AV3 sources in the PIP window. NOTE: CVI cannot be displayed in the PIP window, and AV4 and AV5 do not function with PIP. For information on connecting accessory devices to the AV inputs, see the
Directions for Use manual that came with your set. Connection information begins on page 6.
PIP Window
Main Screen
U
SING THE
PIP B
UTTONS
U sing the PIP buttons on the remote, you can move the PIP window around and swap it with the main screen. You can also freeze the PIP window picture. Perform the steps below to practice using the PIP buttons.
1
2
3
4
5
6
Press the PIP on/off button to show the PIP window.
The window appears in a corner of the TV screen. Press the PIP on/off button again to reduce the PIP window size, and a third time to remove the PIP window from the screen. Press the PIP on/off button again to show the PIP window.
Press the PIP CH DN/UP buttons to tune to channels in the PIP window.
If you press and hold the PIP CH UP button for three seconds, the set will automatically perform a forward scan for channels. Press and hold the PIP CH DN button for three seconds, and the set will automatically perform a backward scan for channels. Auto scanning will stop if you press any key, and it will also stop upon reaching the channel at which scanning began.
Press the PIP POSITION button to move the PIP window from corner to corner on the TV screen.
With PIP on the TV screen, press the SWAP button to
swap the main and PIP pictures. Press SWAP again to swap the pictures back.
NOTE: The CVI source is not accessible in the PIP window, so it cannot be swapped between the main screen and
PIP.
Press the FREEZE button to stop motion within the
PIP window.
The FREEZE button allows you plenty of time to write down on-screen information such as phone numbers or addresses.
Press the PIP on/off button, multiple times if necessary, to remove the PIP window from the screen.
W
ARNING
To prevent uneven picture tube aging, do not leave stationary images on screen for extended periods of time. Vary your picture viewing.
See page 60 in the Directions for Use manual.
A
DJUSTING
PIP T
INT AND
C
OLOR
T he Picture-in-Picture (PIP) TINT control allows you to adjust the PIP picture to obtain natural skin tones. The COLOR control allows you to fine tune the color.
1 Press the MENU/SELECT button. The onscreen menu appears. Then press the CURSOR RING DOWN twice to highlight FEATURES.
2 Press the CURSOR RING RIGHT to enter the FEA-
TURES submenu. Then press the CURSOR RING DOWN repeatedly until the PIP item is highlighted. Press the CUR-
SOR RING RIGHT to enter the PIP submenu.
3
4
Press the CURSOR RING RIGHT or LEFT to adjust the
TINT or COLOR to the desired level.
Press the STATUS/EXIT button to exit the menu.
POWER
4
2
TV
SWAP
SOUND
DN
PIP CH
VCR ACC
ACTIVE
CONTROL FREEZE
UP
PICTURE
5
STATUS/
EXIT
MENU/
SELECT
MUTE
VOL CH
1
4
3
7
TV/VCR
A/CH
POSITION
8
0
2
5
PIP
3
6
9
SURF
1,6
FEATURES
TIMER
AutoLock
PIP
CLOSED CAP
FORMAT
TINT
FEATURES
PIP
TINT
COLOR
POWER
4
STATUS/
EXIT
SOUND
TV
SWAP
DN
PIP CH
VCR
UP
ACC
ACTIVE
CONTROL FREEZE
PICTURE
2,3
MENU/
SELECT
FEATURES
PIP
TINT
COLOR
VOL
1
4
7
TV/VCR
A/CH
8
0
2
5
MUTE
3
6
9
SURF
CH
1
7
POSITION
SWAP
Ski Vacations
P.O. Box 55512
Anytown, USA 87654
1-800-555-1212
FREEZE
44
44
H ELPFUL H INT
When you press the PIP on/off button to show the PIP window, the window will appear where it was located the last time it was displayed.
A
DJUSTING THE
M
ANUAL
C
ONVERGE
C
ONTROLS
C
ONVERGE
R
ED
/B
LUE
B umps and vibrations, moving the set, or the presence of magnetic fields (from speakers, for example) can cause the beams of light coming from the TV’s three color projection tubes to become misaligned. The result is color haloes, or outlines, around por-
tions of the picture. If your picture looks okay, there’s no need to adjust convergence. If your TV’s picture has the color haloes, however, refer to the chart to the right for guidance as to which convergence controls to use, then follow the simple steps below.
1
2
3
Press the MENU/SELECT button. The menu appears. Press the CURSOR RING RIGHT to enter the PICTURE submenu.
Then press the CURSOR RING DOWN until MANUAL
CONVERGE is highlighted.
Press the CURSOR RING RIGHT to enter the MANUAL
CONVERGE submenu. If you want to adjust the Red
Convergence, press the CURSOR RING RIGHT to enter the adjust mode. If you want to adjust the Blue Convergence, press the CURSOR RING DOWN to highlight CONVERGE
BLUE, then press the CURSOR RING RIGHT to enter adjust mode.
In adjust mode, press the CURSOR RING RIGHT, LEFT,
UP, or DOWN to adjust the cross hair until the color halo around it is gone. (The adjustment is automatically saved in the TV’s memory.) To return to the MANUAL CONVERGE menu, press the MENU/SELECT button. To exit the on-screen display, press the STATUS/EXIT button.
Screen
Appearance
Various parts of the picture have red haloes.
Actions
Adjust the
CONVERGE
RED control.
Then if any red haloes remain, adjust the MULTI-
POINT RED control.
Various parts of the picture have blue haloes.
Adjust the
CONVERGE
BLUE control.
Then if any blue haloes remain adjust the MULTI-
POINT BLUE control.
PICTURE
MANUAL CONVERGE
CONVERGE RED
CONVERGE BLUE
MULTIPOINT RED
MULTIPOINT BLUE
SAVE MULTIPOINT
STATUS/
EXIT
POWER
SOUND
TV
SWAP
DN
PIP CH
UP
VCR ACC
ACTIVE
CONTROL FREEZE
PICTURE
2,3
MENU/
SELECT
VOL
1
4
7
TV/VCR
A/CH
8
0
2
5
MUTE
3
6
9
SURF
CH
1
Converge Red
Converge Red
M
ULTIPOINT
R
ED
/B
LUE
he Multipoint Red/Blue Convergence controls enable you to adjust T the convergence at specific points on the TV screen.
NOTE: The on-screen display will leave the screen after 20 seconds of inactivity. If this happens, simply press the MENU/SELECT button to bring the MANUAL CONVERGE submenu back.
1
2
3
4
5
6
Press the MENU/SELECT button. The menu appears.
Press the CURSOR RING RIGHT to enter the PICTURE menu. Then press the CURSOR RING DOWN until MAN-
UAL CONVERGE is highlighted.
Press the CURSOR RING RIGHT to enter the MANU-
AL CONVERGE submenu. Press the CURSOR RING
DOWN until MULTIPOINT RED or MULTIPOINT BLUE is highlighted. Then press the CURSOR RING LEFT or
RIGHT to enter Navigate mode.
Press the CURSOR RING LEFT, RIGHT, UP, or
DOWN to move to a cross hair that has a color outline.
Then press the STATUS/EXIT button to enter adjust mode.
Press the CURSOR RING LEFT, RIGHT, UP, or
DOWN to adjust the cross hair image until the color
outline is gone. Then press the STATUS/EXIT button to return to NAVIGATE mode. Repeat steps 3 and 4 until all misaligned cross images have been adjusted.
After making your adjustments, you must store them in the TV’s memory using SAVE MULTIPOINT.
NOTE: If you are not satisfied with the adjustments you just made and want to start over, you can use the UNDO
MULTIPOINT control. This control allows you to undo the adjustments, but it will work only if you use it before saving.
To save your multipoint adjustments, press the
MENU/SELECT button. This returns you to the MANU-
AL CONVERGE menu. Press the CURSOR RING DOWN until SAVE MULTIPOINT is highlighted. Then press the
CURSOR RING LEFT or RIGHT to store your adjustments in the TV’s memory.
OR
To undo the multipoint adjustments you just made,
press the MENU/SELECT button. This returns you to the MANUAL CONVERGE menu. Press the CURSOR
RING DOWN until UNDO MULTIPOINT is highlighted.
Press the CURSOR RING LEFT or RIGHT to undo the adjustments. Press the CURSOR RING UP until MULTI-
POINT RED or MULTIPOINT BLUE is highlighted. Press the CURSOR RING LEFT or RIGHT to enter Navigate mode. Then Follow steps 3–5 above to make your adjustments again.
OR
To restore the TV’s convergence to factory settings,
press the MENU/SELECT button. This returns you to the MANUAL CONVERGE menu. Press the CURSOR
RING DOWN until RESTORE FACTORY is highlighted.
Then press the CURSOR RING LEFT or RIGHT to restore the TV’s convergence to factory settings.
Press the STATUS/EXIT button to exit the submenu.
PICTURE
MANUAL CONVERGE
CONVERGE RED
CONVERGE BLUE
MULTIPOINT RED
MULTIPOINT BLUE
SAVE MULTIPOINT
POWER
PICTURE
MANUAL CONVERGE
▲▲
CONVERGE RED
CONVERGE BLUE
MULTIPOINT RED
MULTIPOINT BLUE
SAVE MULTIPOINT
É to Navigate Exit to Adjust to Navigate Exit to Adjust to Adjust Exit to Navigate
3,4
SOUND
SWAP
TV
DN
PIP CH
VCR
UP
ACC
ACTIVE
CONTROL FREEZE
PICTURE
2
MENU/
SELECT
STATUS/
EXIT
6
VOL
7
TV/VCR
A/CH
1
4
POSITION
8
0
2
5
MUTE
3
6
9
SURF
CH
1,5
PIP to Navigate Exit to Adjust to Adjust Exit to Navigate
PICTURE
MANUAL CONVERGE
▲▲
CONVERGE RED
CONVERGE BLUE
MULTIPOINT RED
MULTIPOINT BLUE
SAVE MULTIPOINT
É to Adjust Exit to Navigate
PICTURE
MANUAL CONVERGE
▲
CONVERGE RED
CONVERGE BLUE
MULTIPOINT RED
MULTIPOINT BLUE
SAVE MULTIPOINT
SAVE MULTIPOINT
PICTURE
MANUAL CONVERGE
▲
CONVERGE RED
CONVERGE BLUE
MULTIPOINT RED
MULTIPOINT BLUE
SAVE MULTIPOINT STORED
H
ELPFUL
H
INT
If you should experience a power outage before saving your multipoint-convergence settings, your settings will be lost.
PICTURE
MANUAL CONVERGE
▲
CONVERGE BLUE
MULTIPOINT RED
MULTIPOINT BLUE
SAVE MULTIPOINT
UNDO MULTIPOINT
OR
UNDO MULTIPOINT
PICTURE
MANUAL CONVERGE
▲
CONVERGE BLUE
MULTIPOINT RED
MULTIPOINT BLUE
SAVE MULTIPOINT
UNDO MULTIPOINT RESTORED
PICTURE
MANUAL CONVERGE
▲
MULTIPOINT RED
MULTIPOINT BLUE
SAVE MULTIPOINT
UNDO MULTIPOINT
RESTORE FACTORY
OR
RESTORE FACTORY
PICTURE
MANUAL CONVERGE
▲
MULTIPOINT RED
MULTIPOINT BLUE
SAVE MULTIPOINT
UNDO MULTIPOINT
RESTORE FACTORY RESTORED
8
Advertisement