Amplifier Manual

Manual del Amplificador

Manuel del’amplificateur

Features:

• High Efficiency Class D Topology

• Compact Size for Easy Installation

• Balanced Differential Input Circuitry

• Audiophile NJM2068M Operational Amplifiers

• Ultra High Speed IR Class D Chipset

• High, Band and Low Pass Crossovers

• ADAPT Power Management System

• Surface Mount Component Technology

• Direct Insert Power and Speaker Terminals

• Audio Precision Quality Control Verification

• High Temperature Plexiglass cover

• Signal Clipping Indicators

• RMD - Remote Monitoring Display Port

• RBCF- Remote Subwoofer Level Control included

(Ti2 1600.5)

Características:

• Alta eficiencia de clase D Topología

• Tamaño compacto para fácil instalación

• Diferencial balanceada circuitos de entrada

• Audiophile NJM2068M amplificadores operacionales

• IR Chipset Ultra Alta Velocidad

• Crossovers paso alto y bajo

• ADAPT Sistema de Gestión de Energía

• Tecnología “Surface Mount Component”

• Conexiones directas de terminales de poder y de

parlantes

• Control de verificación de calidad de precisión de audio

• Cubierta de Plexiglás resistente a altas temperaturas

• RMD - Puerto de display para monitoreo remoto

• RBCF - Control de nivel de Subwoofer remoto incluido

(Ti2 1600.5)

Models: Ti2 1000.4, Ti2 1600.5

Caractéristiques:

• Petit format pour faciliter l’installation

• Topologie de classe D de gamme complète

• Circuit équilibré Entrée différentielle

• Audiophile NJM2068M Amplificateurs opérationnels

• Haute Vitesse IR de classe D chipset

• Filtres croisés passe-haut et passe-bas

• ADAPT système d’alimentation

• Technologie de composant monté en surface

• Terminaux d’alimentation et de haut-parleurs à

insertion directe

• Vérification du contrôle de la qualité de la précision audio

• Couvercle de plexiglas résistant aux températures élevées

• RMD - Entrée De L’affichage de Tension a Distance

• RBCF- Niveau de contrôle de passe-bas inclus (Ti2 1600.5)

Amplifier Owner’s Manual

SPECIFICATIONS

Ti2 1000.4 SPECIFICATIONS

Frequency Response:

Signal to Noise Ratio:

± 1dB from 20Hz to 20kHz

>100dB

Crossover Slopes: 12dB per Octave

Front High/Low Pass Crossover Range: 45Hz to 4kHz

Rear High Pass Crossover Range: 20Hz to 4kHz

Rear Low Pass Crossover Range: 40Hz to 4kHz

Low Level Input Range: 200 millivolts to 8 volts

Lowest Recommend Load:

Typical Efficiency:

Damping Factor

4 ohms Bridged/2 ohms Stereo

80%

Greater than 200

RMS Power Output 150w x 4 @ 4 ohms Stereo

250w x 4 @ 2 ohms Stereo

500w x 2 @ 4 ohms Bridged

Power/Ground Wire Size: 4 Gauge

Recommend Power Wire Fuse: 80a

Dimensions: 11.7” L x 7.1” W x 2.0” H

296mm L x 180mm W x 52mm H

Ti2 1600.5 SPECIFICATIONS

FRONT AND REAR CHANNELS:

Frequency Response: ± 1dB from 20Hz to 20kHz

Signal to Noise Ratio:

Crossover Slopes:

>100dB

12dB per Octave

Front High Pass Crossover Range: 20Hz to 4kHz

Rear High Pass Crossover Range: 20Hz to 4kHz

Rear Low Pass Crossover Range: 40Hz to 4kHz

Low Level Input Range:

Lowest Recommend Load:

Typical Efficiency:

Damping Factor

200 millivolts to 8 volts

4 ohms Bridged/2 ohms Stereo

80%

Greater than 200

RMS Power Output

SUBWOOFER CHANNEL:

Frequency Response:

Signal to Noise Ratio:

Crossover Slopes:

Low Pass Crossover Range:

Subsonic Crossover Range:

Variable Phase:

Low Level Input Range:

Lowest Recommend Load:

Typical Efficiency:

Damping Factor:

± 1dB from 20Hz to 300Hz

>100dB

12dB per Octave

20Hz to 300Hz

10Hz to 50Hz

0 to 180 degrees

200 millivolts to 8 volts

2 ohms

80%

Greater than 200

125w x 4 @ 4 ohms Stereo

200w x 4 @ 2 ohms Stereo

400w x 2 @ 4 ohms Bridged

RMS Power Output 500w x 1 @ 4 ohms

800w x 1 @ 2 ohms

Recommend Power Wire Fuse:

Power/Ground Wire Size:

Dimensions:

100a

4 Gauge

14.4” L x 7.1” W x 2.0” H

366mm L x 180mm W x 52mm H

POWER OUTPUT NOTE: A power birth certificate is included for each amplifier. Ti2 amplifiers are conservatively rated and will exceed their RMS power rating shown here. All RMS power ratings and measurements are at 14.4 volts with no more than

1% THD. Ti2 1000.4 and Ti2 1600.5 feature ADAPT technology which provides the same power output from 11 to 15 volts with music material. www.phoenixgold.com

RMS Power Output 150w x 4 @ 4 ohms Stereo

250w x 4 @ 2 ohms Stereo

500w x 2 @ 4 ohms Bridged

Power/Ground Wire Size: 4 Gauge

Recommend Power Wire Fuse: 80a

Dimensions: 11.7” L x 7.1” W x 2.0” H

296mm L x 180mm W x 52mm H

RMS Power Output 125w x 4 @ 4 ohms Stereo

200w x 4 @ 2 ohms Stereo

400w x 2 @ 4 ohms Bridged

RMS Power Output 500w x 1 @ 4 ohms

800w x 1 @ 2 ohms

Recommend Power Wire Fuse:

Power/Ground Wire Size:

Dimensions:

100a

4 Gauge

14.4” L x 7.1” W x 2.0” H

366mm L x 180mm W x 52mm H

Amplifier Owner’s Manual

A BALANCED DIFFERENTIAL INPUTS

Provides maximum rejection of unwanted noise from upstream components.

B AUDIOPHILE NJM2068M OP-AMPS

Most mobile amplifiers today use the standard NJM4558 op-amp which has a bandwidth of 3MHz, slew rate of 1V/uSec and noise level of 1.4uV.

The NJM2068M is simply a better performer with a bandwidth of 19MHz, slew rate of 6V/uSec and noise level of .44uV.

The result is quieter, faster and wider bandwidth performance that ensures the original music material is reproduced as accurately as possible.

Key Features

C

D

ULTRA HIGH SPEED IR CLASS D CHIPSET

State of the art IR20957 chipset switches at more than 300kHz for blistering audio performance. All four or five chipsets are sync’d together in unison to eliminate unwanted harmonics or distortion.

POST FILTER FEEDBACK

Feedback is when part of the output signal is “fed back” into the original signal to ensure stability and accurate sound. Class D amplifiers use output filters (see the 4 vertical coils below), but most DO NOT INCLUDE these filters in the feedback loop. Ti2 amplifiers INCLUDE or take feedback after its passed through these filters. The result is more accurate sound that rivals some of the best class A/B amplifiers.

G

D

E

F

C

B

A

E ADAPT POWER MANAGEMENT SYSTEM

Full power output from 11 to 15 volts: ADAPT delivers the same output power regardless of the vehicle’s electrical system voltage. Instantaneous or long term voltage drops have no effect on the amplifier’s power output. This means more dynamic and less distorted audio output.

Dual power modes provide maximum efficiency: ADAPT seamlessly optimizes the power supply and Class D operating circuitry by adapting to the end user’s listening habits. When the ADAPT circuit senses lower signal levels, it will automatically optimize the amplifier’s power supply and Class

D circuitry to a low power mode that maximizes efficiency and minimizes heat to almost zero. As a signal increase is detected the amplifier instantly shifts into a high power mode, where the power supply and Class D sections are now optimized to deliver massive power and headroom for those demanding listening sessions. The amplifier is constantly monitoring and adapting between these modes which results in higher overall efficiency, much lower operating temperatures and rock solid reliability.

F

G

THERMAL ROLLBACK CIRCUIT

Under most conditions, Ti2 amplifiers generate moderate to low heat. However, if extreme conditions exist, as temperatures rise the amplifier will automatically adjust the power output, so your music continues to play. These changes are inaudible and vastly reduce the chance for any thermal shutdown events.

LOW EMI CIRCUIT BOARD DESIGN

Most class D amplifiers can emit EMI noise that can cause problems with AM/FM reception or other devices in the vehicle. Ti2 amplifiers have undergone intense real world engineering and testing to vastly reduce or eliminate these issues. Careful PCB layout using four layers (most amplifiers feature just two) along with many key filters ensures a very low possibility of any interference issues. www.phoenixgold.com

Amplifier Owner’s Manual

Ti2 1000.4

4 Channel Power Amplifier

FRONT AND REAR INPUTS

Connect preamp signal cables from headunit to these inputs. The front and rear inputs must be used, if only the front input is used then the rear speaker outputs will have no output signal.

HPF/LPF CROSSOVER FREQUENCY

Controls the crossover points for the speaker outputs.

SENS

Used to reach maximum amplifier power with a wide variety of headunits.

X-OVER CONFIG

FLAT: Crossovers are turned off

HPF: High pass crossover is on

LPF: Low pass crossover is on

LP/BP: Low and high pass crossovers are both on, creating a Bandpass (BP) filter for midbass/midrange drivers. If running a subwoofer the HPF now becomes a subsonic filter, to turn off the HPF/subsonic filter set it to 20Hz.

Note: The front HP and rear LP crossovers extend to 4kHz, so its possible to run a component speaker system fully active. The tweeters would be powered by the front channels and the midbasses by the rear channels. Be sure to check with your speaker’s manufacture for the correct tweeter and midbass crossover points to avoid speaker damage.

+12V

This must be connected to the fused positive terminal (+12V) of the car’s battery. The fuse must be located within 18 inches of the battery.

REMOTE

This must be connected to switched +12V, usually a trigger wire coming from the head unit or ignition.

GROUND

This must be connected to the negative terminal of the car’s battery or bolted to a clean, unpainted part of the chassis of the vehicle.

REMOTE MONITORING DISPLAY (RMD)

Connect optional RMD Voltage Display to this port.

SPEAKER OUTPUTS

Used to connect the amplifier to speakers. Ti2 1000.4’s minimum impedance is 4 ohms bridged or 2 ohms stereo. Use the Left + and

Right - to bridge the channels.

CLIP INDICATORS (located on top of the amplifier)

Lights when the amplifier reaches near maximum output. Under heavy use the clip indicators should be flashing during the peaks of the music. The clip indicator should not stay lit for long periods of time (more than 1 or 2 seconds), if this is the case you need to reduce system volume or the SENS of the amplifier.

www.phoenixgold.com

Amplifier Owner’s Manual

Ti2 1600.5

5 Channel Power Amplifier

FRONT, REAR AND SUB INPUTS

Connect preamp signal cables from headunit to these inputs.

SUB INPUT SWITCH

Determines which input will feed signal to the subwoofer channel.

“OUT” or SUB = Use the Sub Input

“IN” or F/R = Use the Front and Rear inputs as its signal will be summed then sent to the sub channel of the amplifier

HPF/LPF/SUBSONIC CROSSOVER FREQUENCY

Controls the crossover points for the speaker outputs.

REAR X-OVER CONFIG

HP: High pass crossover is on

BP: Low and high pass crossovers are both on, creating a Bandpass (BP) filter for midbass/midrange drivers. Check on page 4 (Ti2 1000.4) for more details on how to use the the BP setting for a fully active crossover system.

SENS

Used to reach maximum amplifier power with a wide variety of headunits.

REMOTE BASS LEVEL CONTROL (RBCF)

This port is for connecting the remote subwoofer level control. This allows up to

20dB of volume adjustment for the subwoofer channel. This is not a bass boost, it controls the level of the low pass signal.

PHASE

This allows the phase of the subwoofer output to be adjusted from 0 to 180 degrees. This adjustment can help achieve better “up front” subwoofer bass and resolve subwoofer cancellation problems in certain installations. Each installation is different, slowly adjust and listen for best results.

+12V

This must be connected to the fused positive terminal (+12V) of the car’s battery. The fuse must be located within 18 inches of the battery.

REMOTE

This must be connected to switched +12V, usually a trigger wire coming from the head unit or ignition.

GROUND

This must be connected to the negative terminal of the car’s battery or bolted to a clean, unpainted part of the chassis of the vehicle.

REMOTE MONITORING DISPLAY (RMD)

Connect optional RMD Voltage Display to this port.

SPEAKER OUTPUTS

Used to connect the amplifier to speakers. Ti2 1600.5’s minimum impedance is 4 ohms bridged or 2 ohms stereo on front and rear channels. Use the Left + and Right - to bridge the channels. Minimum impedance is 2 ohms for the subwoofer channel and its not bridgeable.

CLIP INDICATORS (located on top of the amplifier)

Lights when the amplifier reaches near maximum output. Under heavy use the clip indicators should be flashing during the peaks of the music. The clip indicator should not stay lit for long periods of time (more than 1 or 2 seconds), if this is the case you need to reduce system volume or the SENS level of the amplifier.

www.phoenixgold.com

Amplifier Owner’s Manual

Ti2 1000.4 Crossover settings

clicks

19

20

21

22

23

16

17

18

13

14

15

8

9

10

11

12

5

6

7

3

4

1

2

33

34

35

30

31

32

36

37

38

39

40

41

27

28

29

24

25

26

All crossover frequency potentiometers have 41 detents or “clicks” so the end user can set the exact cross over frequency desired.

FRONT AND REAR CHANNELS

FRONT HP

(45~4kHz)

291

313

330

350

383

93

105

121

143

172

215

57

63

68

50

51

54

75

83

49

49

50

50

887

1.0k

1.3k

1.5k

1.6k

1.9k

2.0k

2.4k

2.9k

3.6k

4.1k

4.1k

409

442

494

544

624

737

REAR HP

(45~4kHz)

288

306

330

364

380

97

112

132

162

204

274

51

55

61

67

83

44

45

48

43

44

44

44

1.0k

1.2k

1.3k

1.5k

1.7k

1.9k

2.2k

2.7k

3.0k

3.6k

3.7k

3.7k

411

460

503

579

671

778

REAR HP

(20~4kHz)

121

128

135

146

159

62

75

93

41

47

54

28

29

31

34

37

23

24

26

22

22

22

22

372

472

666

738

832

974

1.2k

1.5k

2.0k

3.1k

3.8k

3.9k

171

188

209

230

267

309

REAR LP

(40~4kHz)

215

232

246

266

290

77

92

108

131

164

202

37

37

44

56

65

36

37

37

36

36

36

36

797

1.1k

1.2k

1.4k

1.6k

1.8k

2.1k

2.7k

3.3k

4.0k

4.1k

4.1k

316

352

398

441

524

626 www.phoenixgold.com

Amplifier Owner’s Manual clicks

26

27

28

23

24

25

18

19

20

15

16

17

21

22

12

13

14

9

10

11

4

5

6

7

8

1

2

3

37

38

39

34

35

36

40

41

29

30

31

32

33

All crossover frequency potentiometers have 41 detents or “clicks” so the end user can set the exact cross over frequency desired.

FRONT AND REAR CHANNELS SUB CHANNEL

FRONT HP

(20~4kHz)

153

165

178

197

221

253

81

106

126

47

54

66

133

144

33

36

41

27

28

30

23

23

24

23

23

23

25

25

809

955

1.1k

1.4k

2.1k

2.8k

3.7k

3.8k

291

355

461

649

728

REAR HP

(20~4kHz)

164

176

194

216

238

279

98

125

132

53

62

76

141

152

36

40

46

28

30

33

24

24

24

24

24

24

26

27

844

955

1.2k

1.5k

2.0k

2.8k

3.7k

3.7k

328

381

503

673

746

REAR LP

(40~4kHz)

269

291

320

352

394

444

87

103

123

153

200

217

234

247

49

64

74

36

39

41

34

34

35

34

34

34

35

36

1.3k

1.5k

1.7k

2.0k

2.5k

3.0k

4.1k

4.1k

520

614

768

958

1.1k

SUBSONIC

(10~50hz)

29

30

30

27

27

28

32

33

25

26

27

21

21

23

19

19

19

18

18

18

20

20

17

17

18

17

17

17

43

43

44

44

40

41

42

38

39

40

34

35

37

LP

(30~300Hz)

128

133

139

146

154

162

172

181

99

117

123

65

74

85

37

41

46

27

30

33

51

57

27

27

27

27

27

27

264

272

282

295

303

315

315

193

203

221

237

244

252 clicks

24

25

26

21

22

23

27

28

18

19

20

15

16

17

10

11

12

13

14

7

8

9

4

5

6

1

2

3

38

39

40

41

35

36

37

32

33

34

29

30

31 www.phoenixgold.com

Manual del Amplificador

Ti2 1000.4

Amplificador de Potencia de 4 Canales

ENTRADAS DELANTERA y TRACERA

Conectar cables de señal de preamp del radio a estas entradas. Ambas entradas, Front y Rear deben ser usadas, si solo se usa el Front no habrá señal en el Rear output.

FRECUENCIA de CROSSOVER

Controla el nivel de frecuencia de crossover.

SENS

Usado para alcanzar el máximo poder amplificado con una gran variedad de radios.

CONFIGURACION

FLAT: El crossover es off

HP: El crossover high pass es “on”

LP/BP: El crossover low y high pass es “on”

+12V

Este debe ser conectado al fusible del terminal positivo (+12V) de la batería del auto. El fusible debe ser ubicado a menos de 18 pulgadas de la batería.

REMOTO

Este debe ser conectado al shwich +12V. Usualmente al cable de gatillo que viene del radio o del encendido.

TIERRA

Este debe ser conectado al terminal negativo de la batería del auto o a una parte limpia y sin pintura del chasis del auto.

DISPLAY PARA MONITOREO REMOTO (RMD)

Conectar el display de voltaje opcional RMD a este puerto.

SALIDA de PARLANTES

Usado para conectar los parlantes. La mínima impedancia para el Ti2

1000.4 es 4 ohms o 2 ohms estéreo. Usar Left+ y Right – para el bridge.

INDICADORES CLIP

Se ilumina cuando el amplificador llega a cerca de la salida máxima. En condiciones de uso pesado de los indicadores de clip debe parpadear durante los picos de la música. El indicador de saturación no debe permanecer encendida durante largos períodos de tiempo (más de 1 o 2 segundos), si este es el caso de tener que reducir el volumen del sistema o nivel del amplificador. www.phoenixgold.com

Manual del Amplificador

Ti2 1600.5

Amplificador de Potencia de 5 Canales

ENTRADAS

Conectar cables de señal de preamp del radio a estas entradas. Las entradas frontales, traseros y sub debe ser utilizado. Si una entrada no se utiliza no habrá salida para ese conjunto de canales.

HPF/LPF FRECUENCIA de CROSSOVER

Controla el nivel de frecuencia de crossover.

SUB SELECCION DE ENTRADE

Determina qué entrada se alimenta la señal en el canal de subwoofer.

“OUT” o SUB = Usar la entrada Sub

“IN” o F / R = Usa el frontal y las entradas traseras que su señal se sumarán luego enviado a la sub canal del amplificador.

SENS

Usado para alcanzar el máximo poder amplificado con una gran variedad de radios.

PHASE

Esto permite que la fase de la salida para ajustarse de 0 a 180 grados. Este ajuste puede ayudar a lograr una mejor “up front” bass subwoofer y resolver los problemas subwoofer cancelación en determinadas instalaciones. Cada instalación es diferente, ajuste lentamente y escuchar para obtener mejores resultados.

CONTROL REMOTO de NIVEL de BAJOS

Este puerto es para conectar el control de nivel de bajos. Esto permite un ajuste de hasta 20dB de volumen. Este no es un bass bost, este controla el nivel de low pass signal.

+12V

Este debe ser conectado al fusible del terminal positivo (+12V) de la batería del auto. El fusible debe ser ubicado a menos de 18 pulgadas de la batería.

REMOTO

Este debe ser conectado al shwich +12V. Usualmente al cable de gatillo que viene del radio o del encendido.

TIERRA

Este debe ser conectado al terminal negativo de la batería del auto o a una parte limpia y sin pintura del chasis del auto.

DISPLAY PARA MONITOREO REMOTO (RMD)

Conectar el display de voltaje opcional RMD a este puerto.

SALIDA de PARLANTES

Usado para conectar los parlantes. La mínima impedancia para el Ti2

1600.5 es 4 ohms o 2 ohms estéreo. Usar Left + y Right – para el bridge.

Impedancia mínima es de 2 ohms para el canal de subwoofer y no es bridgeable.

INDICADORES CLIP

Se ilumina cuando el amplificador llega a cerca de la salida máxima. En condiciones de uso pesado de los indicadores de clip debe parpadear durante los picos de la música. El indicador de saturación no debe permanecer encendida durante largos períodos de tiempo (más de 1 o 2 segundos), si este es el caso de tener que reducir el volumen del sistema o nivel del amplificador. www.phoenixgold.com

Manuel de l’amplificateur

Ti2 1000.4

amplificateur de puissance

ENTRÉE

Reliez les câbles de signal préampli de l’unité principale sur ces bornes.

FRÉQUENCE DE FILTRE PASSIF PASSE-BAS et

PASSE-HAUT

Contrôle les points de filtre pour les sorties du haut-parleur.

NIVEAU

Sert à atteindre une puissance d’amplificateur maximale avec une grande variété d’unités principales.

CONFIG

FLAT : Croisé est éteint.

HP : L’haute passe croisée est sur.

LP/BP : Basse et haute croisements de passage sont à la fois sur.

+12V

Doit être relié à la borne positive protégée par fusible (+12 V) de la batterie de la voiture. Le fusible doit être situé à moins de 18 pouces de la batterie.

BORNE TÉLÉCOMMANDE

Doit être relié à la borne +12 V commutée, généralement un fil d’amorçage sortant de l’unité principale ou de l’allumage.

MASSE

Doit être relié à la borne négative de la batterie de la voiture ou boulonné sur un élément propre et non peint du châssis du véhicule.

ENTRÉE DE L’AFFICHAGE DE TENSION A DISTANCE (RMD)

Connectez le RMD d’affichage de tension facultatif à cette prise jack.

SORTIES ENCEINTES

Utilisé pour connecter l’amplificateur aux enceintes. Ti2 1000.4 impédance minimale est de 4 ohms ponté ou stéréo 2 ohms.

INDICATEURS CLIP

S’allume lorsque l’amplificateur atteint près de sortie maximale. Cas d’utilisation intensive les indicateurs d’écrêtage doit clignoter pendant les pics de la musique.

L’indicateur d’écrêtage ne devrait pas rester allumé pendant de longues périodes de temps (plus de 1 ou 2 secondes), si c’est le cas, vous devez réduire le volume du système ou au niveau de l’amplificateur. www.phoenixgold.com

Manuel de l’amplificateur

Ti2 1600.5

amplificateur de puissance

ENTRÉE

Reliez les câbles de signal préampli de l’unité principale sur ces bornes.

FRÉQUENCE DE FILTRE PASSIF PASSE-BAS et

PASSE-HAUT

Contrôle les points de filtre pour les sorties du haut-parleur.

PHASE

Ceci permet à la phase de la sortie à être ajustée de 0 à 180 degrés.

Cet ajustement peut aider à atteindre une meilleure bass “up front” subwoofer et résoudre les problèmes d’annulation caisson de graves dans certaines installations. Chaque installation est différente, ajustez lentement et d’écouter pour obtenir les meilleurs résultats.

NIVEAU

Sert à atteindre une puissance d’amplificateur maximale avec une grande variété d’unités principales.

COMMANDE À DISTANCE DU NIVEAU DES BASSES

Ce port sert à connecter la télécommande de niveau. Cela permet un ajustement du volume allant jusqu’à 20 dB. Ce n’est pas une amplification des basses mais permet de contrôler le niveau du signal du filtre passe-bas.

SÉLECTION D’ENTRÉE SUB

Détermine quelle source sera signal de nourrir le canal de subwoofer.

“OUT” ou SUB = utiliser l’entrée Sub

“IN” ou F / R = Utilisez le Front et les entrées arrières comme son signal seront additionnées puis envoyé à la sous-canal de l’amplificateur.

+12V

Doit être relié à la borne positive protégée par fusible (+12 V) de la batterie de la voiture. Le fusible doit être situé à moins de 18 pouces de la batterie.

BORNE TÉLÉCOMMANDE

Doit être relié à la borne +12 V commutée, généralement un fil d’amorçage sortant de l’unité principale ou de l’allumage.

MASSE

Doit être relié à la borne négative de la batterie de la voiture ou boulonné sur un élément propre et non peint du châssis du véhicule.

ENTRÉE DE L’AFFICHAGE DE TENSION A DISTANCE (RMD)

Connectez le RMD d’affichage de tension facultatif à cette prise jack.

SORTIES ENCEINTES

Utilisé pour connecter l’amplificateur aux haut-parleurs. Ti2 1600.5 impédance d

‘minimum est de 4 ohms ponté ou 2 ohms stéréo. Canal Subwoofer est stable à

2 ohms.

INDICATEURS CLIP

S’allume lorsque l’amplificateur atteint près de sortie maximale. Cas d’utilisation intensive les indicateurs d’écrêtage doit clignoter pendant les pics de la musique.

L’indicateur d’écrêtage ne devrait pas rester allumé pendant de longues périodes de temps (plus de 1 ou 2 secondes), si c’est le cas, vous devez réduire le volume du système ou au niveau de l’amplificateur. www.phoenixgold.com

Phoenix Gold

A Division of AAMP of America™

13190 56th Court

Clearwater, Florida 33760

P: 888-228-5560 [email protected]

www.phoenixgold.com

© 2013 AAMP of Florida, Inc

Designed and Engineered in the USA

LIMITED WARRANTY ON AMPLIFIERS

Phoenix Gold warrants this product to be free of defects in materials and workmanship for a period of one (1) year from the original date of purchase. This warranty is not transferable and applies only to the original purchaser from an authorized Phoenix Gold dealer in the United States of America only. Should service be necessary under this warranty for any reason due to manufacturing defect or malfunction, Phoenix Gold will (at its discretion), repair or replace the defective product with new or remanufactured product at no charge. Damage caused by the following is not covered under warranty: accident, misuse, abuse, product modification or neglect, failure to follow installation instructions, unauthorized repair attempts, misrepresentations by the seller. This warranty does not cover incidental or consequential damages and does not cover the cost of removing or reinstalling the unit(s). Cosmetic damage due to accident or normal wear and tear is not covered under warranty.

INTERNATIONAL WARRANTIES:

Products purchased outside the United States of America are covered only by that country’s Authorized Phoenix Gold reseller and not by Phoenix Gold. Consumers needing service or warranty information for these products must contact that country’s reseller for information.