Instruction manual

ESPAÑOL: PÁGINA 15

FRANÇAISE : PAGE 29

Router

MODEL

100

To learn more about Porter-Cable visit our website at:

http://www.porter-cable.com

Copyright © 2004 Porter-Cable Corporation

IMPORTANT

Please make certain that the person who is to use this equipment carefully reads and understands these instructions before starting operations.

The Model and Serial No. plate is located on the main housing of the tool. Record these numbers in the spaces below and retain for future reference.

Model No. ______________________________________

Type ___________________________________________

Serial No. _______________________________________

Part No. 907395 - 03-22-04

SAFETY GUIDELINES - DEFINITIONS

This manual contains information that is important for you to know and understand. This information relates to protecting YOUR SAFETY and PREVENTING

EQUIPMENT PROBLEMS. To help you recognize this information, we use the symbols below. Please read the manual and pay attention to these sections. indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.

indicates a potentially hazardous situation which, if not avoided,could result in death or serious injury.

indicates a potentially hazardous situation which, if not avoided,may result in minor or moderate injury.

used without the safety alert symbol indicates potentially hazardous situation which, if not avoided, may result in property damage.

Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known (to the State of

California) to cause cancer, birth defects or other reproductive harm. Some example of these chemicals are: lead from lead-based paints crystalline silica from bricks and cement and other masonry products arsenic and chromium from chemically-treated lumber

Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, always wear

MSHA/NIOSH approved, properly fitting face mask or respirator when using such tools.

Improper operation or maintenance of this product could result in serious injury and property damage. Read and understand all warnings and operating instructions before using this tool. When using power tools, basic safety precautions should always be followed to reduce the risk of personal injury.

For additional information visit our website www.porter-cable.com.

Additional Information regarding the safe and proper operation of power tools (i.e.

a safety video) is available from the Power Tool Institute, 1300 Sumner Avenue,

Cleveland, OH 44115-2851 (www.powertoolinstitute.com). Additional Information is also available from the National Safety Council, 1121 Spring Lake Drive, Itasca,

IL 60143-3201, the American National Standards Institute ANSI 01.1Safety

Requirements for Woodworking Machines, and the U.S. Department of Labor regulations.

There are certain applications for which this tool was

designed. Porter-Cable strongly recommends that this tool NOT be modified and/or used for any application other than for which it was designed. If you have any questions relative to its application DO NOT use the tool until you have written

Porter-Cable and we have advised you.

Technical Service Manager

Porter-Cable Corporation

4825 Highway 45 North

Jackson, TN 38305

2

IMPORTANT SAFETY INSTRUCTIONS

When using electric tools, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and personal injury, including the following:

Read All Instructions.

Read and understand all instructions. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury.

SAVE THESE INSTRUCTIONS.

GROUNDING INSTRUCTIONS

This tool should be grounded while in use to protect the operator from electric shock. The tool is equipped with a 3conductor cord and 3-prong grounding type plug to fit the proper grounding type receptacle. The green (or green and yellow) conductor in the cord is the grounding wire. Never connect the green (or green and yellow) wire to a live terminal.

GROUNDED OUTLET BOX

CURRENT

CARRYING

PRONGS

If your unit is for use on less than 150 V, it has a plug that looks like that shown in

Figure (A).

GROUNDING PRONG

IS LONGEST OF THE 3 PRONGS

Fig. A

GROUNDED OUTLET BOX

GROUNDING MEANS

ADAPTER

If it is for use on 150 to 250 V, it has a plug that looks like that shown in Figure

(C).

An adapter, see Figure (B) is available for connecting Figure (B) type plugs to 2prong receptacles. The green- colored rigid ear, lug, or the like, extending from the adapter must be connected to a permanent ground, such as a properly grounded outlet box. No adapter is available for a plug as shown in Figure

(C).

Fig. B

GROUNDED OUTLET BOX

CURRENT

CARRYING

PRONGS

EXTENSION CORDS

Use only 3-wire extension cords that have 3-prong grounding-type plugs and

3-pole receptacles that accept the tool’s plug. Replace or repair damaged cords.

GROUNDING PRONG

IS LONGEST OF THE 3 PRONGS

Fig. C

3

1. Keep Work Area Clean. Cluttered areas and benches invite injuries.

2. Consider Work Area Environment. Don’t expose power tools to rain.

Don’t use power tools in damp or wet locations. Keep work area well lit. Do not use tool in presence of flammable liquids or gases.

3. Guard Against Electric Shock. Prevent body contact with grounded surfaces. For example; pipes, radiators, ranges, refrigerator enclosures.

4. Keep Children Away. Do not let visitors contact tool or extension cord. All visitors should be kept away from work area.

5. Store Idle Tools. When not in use, tools should be stored in dry, and high or locked-up place – out of reach of children.

6. Don’t Force Tool. It will do the job better and safer at the rate for which it was intended.

7. Use Right Tool. Don’t force small tool or attachment to do the job of a heavy-duty tool. Don’t use tool for purpose not intended – for example – don’t use circular saw for cutting tree limbs or logs.

8. Dress Properly. Do not wear loose clothing or jewelry. They can be caught in moving parts. Rubber gloves and non-skid footwear are recommended when working outdoors. Wear protective hair covering to contain long hair.

9. Use Safety Glasses. Also use face or dust mask if cutting operation is dusty.

10. Don’t Abuse Cord. Never carry tool by cord or yank it to disconnect from receptacle. Keep cord from heat, oil, and sharp edges.

11. Secure Work. Use clamps or a vise to hold work. It’s safer than using your hand and it frees both hands to operate tool.

12. Don’t Overreach. Keep proper footing and balance at all times.

13. Maintain Tools With Care. Keep tools sharp and clean for better and safer performance. Follow instructions for lubricating and changing accessories. Inspect tool cords periodically and if damaged, have repaired by authorized service facility. Inspect extension cords periodically and replace if damaged. Keep handles dry, clean, and free from oil and grease.

14. Disconnect Tools. When not in use, before servicing, and when changing accessories, such as blades, bits, cutters.

15. Remove Adjusting Keys and Wrenches. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on.

16. Avoid Unintentional Starting. Don’t carry tool with finger on switch. Be sure switch is off when plugging in.

17. Extension Cords. Make sure your extension cord is in good condition.

When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. The EXTENSION CORD

SELECTION table shows the correct size to use depending on cord length and nameplate ampere rating. If in doubt, use the next heavier gage. The smaller the gage number, the heavier the cord.

18. Outdoor Use Extension Cords. When tool is used outdoors, use only extension cords intended for use outdoors and so marked.

19. Stay Alert. Watch what you are doing. Use common sense. Do not

4

operate tool when you are tired.

20. Check Damaged Parts. Before further use of the tool, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting, and any other conditions that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced by an authorized service center unless otherwise indicated elsewhere in this instruction manual. Have defective switches replaced by authorized service center. Do not use tool if switch does not turn it on and off.

SAVE THESE INSTRUCTIONS

SPECIFIC SAFETY RULES AND SYMBOLS FOR ROUTERS

1.

HOLD TOOL BY INSULATED GRIPPING SURFACES WHEN

PERFORMING AN OPERATION WHERE THE CUTTING TOOL MAY

CONTACT HIDDEN WIRING OR ITS OWN CORD. Contact with a “live” wire will make exposed metal parts of the tool “live” and shock the operator.

2.

TIGHTEN COLLET NUT SECURELY to prevent the bit from slipping.

3.

PROVIDE CLEARANCE under workpiece for router bit when throughcutting.

4.

CHECK TO SEE THAT THE CORD will not “hang up” during operation.

5.

CLEAR THE ROUTER BIT AREA before starting motor.

6.

MAINTAIN FIRM GRIP ON TOOL to resist starting torque.

7.

KEEP HANDS CLEAR OF BIT WHEN MOTOR IS RUNNING to prevent personal injury.

8.

LET THE MOTOR COME TO A COMPLETE STOP before putting the tool down.

9.

NEVER TOUCH ROUTER BITS AFTER USE. They may be extremely hot.

10. AVOID “CLIMB-CUTTING”.

(See section “USING THE TOOL” in this manual). “Climb-cutting” increases the chance for loss of control resulting in possible personal injury.

11. DO NOT HAND-HOLD THE ROUTER IN AN UPSIDE-DOWN OR

HORIZONTAL POSITION. The motor can separate from the base if not properly attached according to the instructions (See “ATTACHING THE

MOTOR TO THE ROUTER”) section.

12. SOME WOOD CONTAINS PRESERVATIVES WHICH CAN BE TOXIC.

Take extra care to prevent inhalation and skin contact when working with these materials. Request, and follow, any safety information available from your material supplier.

5

SYMBOL

V

A

Hz

W kW l

µF kg

N/cm 2

Pa h min s

3

3

N n

0

DEFINITION

........................ volts

........................ amperes

........................ hertz

........................ watts

........................ kilowatts

........................ microfarads

........................ liters

........................ kilograms

........................ newtons per square centimeter

........................ pascals

........................ hours

........................ minutes

........................ seconds

........................ alternating current

........................ three-phase alternating current

........................ three-phase alternating current with neutral

........................ direct current

........................ no load speed

........................ alternating or direct current

...................... Class II Construction

........................ splash-proof construction

........................ watertight construction

…/min ........................ revolutions or reciprocation per minute

REPLACEMENT PARTS

When servicing use only identical replacement parts.

MOTOR

Many Porter-Cable tools will operate on either D.C., or single phase 25 to 60 cycle A.C. current and voltage within plus or minus 5 percent of that shown on the specification plate on the tool. Several models, however, are designed for A.C. current only. Refer to the specification plate on your tool for proper voltage and current rating.

Do not operate your tool on a current on which the voltage is not within correct limits. Do not operate tools rated A.C.

only on D.C. current. To do so may seriously damage the tool.

EXTENSION CORD SELECTION

If an extension cord is used, make sure the conductor size is large enough to prevent excessive voltage drop which will cause loss of power and possible motor damage. A table of recommended extension cord sizes will be found in this section. This table is based on limiting line voltage drop to 5 volts (10 volts for 230 volts) at 150% of rated amperes.

If an extension cord is to be used outdoors it must be marked with the suffix

W-A or W following the cord type designation. For example – SJTW-A to indicate it is acceptable for outdoor use.

6

115V

230V

0-2

2-3

3-4

4-5

5-6

6-8

8-10

10-12

12-14

14-16

16-18

18-20

RECOMMENDED EXTENSION CORD SIZES FOR USE WITH PORTABLE ELECTRIC TOOLS

Length of Cord in Feet

25 Ft.

50 Ft.

100 Ft.

150 Ft.

200 Ft.

250 Ft.

300 Ft.

400 Ft. 500 Ft.

50 Ft.

100 Ft.

200 Ft.

300 Ft.

400 Ft.

500 Ft.

600 Ft.

800 Ft. 1000 Ft.

18

18

18

16

18

18

18

18

16

16

14

14

16

16

14

14

18

18

18

18

12

12

12

12

14

12

12

10

18

16

16

14

10

10

8

8

12

10

10

8

16

14

14

12

8

6

8

8

10

10

8

8

16

14

12

12

6

6

6

6

10

8

8

6

14

12

12

10

4

4

6

6

6

6

8

6

14

12

10

10

4

4

6

4

6

4

8

6

12

10

10

8

2

2

4

4

4

4

6

6

12

10

8

8

2

2

2

2

FUNCTIONAL DESCRIPTION

F

OREWORD

The router is one of the most useful tools in the woodworking field. It may be used for many cutting and shaping operations such as slotting, mortising, dadoing, grooving, rabbeting, corner-rounding, beading, dovetailing, veining, inlay work, etc.

ASSEMBLY

SELECTING THE BIT

This Router comes with a 1

/

4

" split type collet which accommodates bits with

1

/

4

" shanks.

Disconnect tool from power source while preparing it for use, making adjustments, and when it is not in use.

INSTALLING AND REMOVING THE BIT

B

A

Fig. 1 Fig. 2

DISCONNECT TOOL FROM POWER SOURCE.

7

1. To remove motor unit from base unit: Open the clamp (A) Fig. 1. While holding base, turn power unit COUNTERCLOCKWISE until lower pin (B) in motor housing is disengaged from groove in base. Lift power unit free from base unit.

2.

Clean and insert shank of bit into collet until shank bottoms, then back it out approximately 1/16".

Do not use router bits with a diameter in excess of 1.5" in this tool.

3. Lay power unit on its side on bench with the collet pointing AWAY from you.

4. Place one wrench on flats of chuck with the opposite end of the wrench resting on the bench to your left (Fig. 2).

5. Place other wrench on collet and tighten COUNTERCLOCKWISE.

TIGHTEN FIRMLY.

6. To remove the bit, reverse the procedure.

AVOID POSSIBLE DAMAGE TO COLLET. NEVER TIGHTEN COLLET WITHOUT BIT.

ATTACHING THE MOTOR TO THE ROUTER BASE

DISCONNECT TOOL FROM POWER SOURCE.

1.

Open the clamp (A) Fig. 1 and set the power unit in the base unit.

2.

Align the lower pin of the power unit (B) Fig. 1 with the groove in the base.

3.

Rotate the power unit CLOCKWISE into the base until the upper guide pins are set in the groove of the base.

4.

Close the clamp.

ADJUSTING DEPTH OF CUT

DISCONNECT TOOL FROM POWER SOURCE.

1.

Open the clamp (A) Fig. 3A.

2.

Hold the base (E) and turn the power unit (F) Fig. 3A COUNTER-CLOCK-

WISE until the tip of the bit is above the bottom of the base.

3.

Set the tool on a flat surface.

4.

Turn the power unit (F) Fig. 3A CLOCKWISE until bit touches the work.

5.

Close the clamp (A) Fig. 3A.

6.

Rotate the depth adjusting ring (B) Fig. 3A until the zero-line (C) Fig. 3B is opposite the index line (D) Fig. 3B on the housing.

7.

Open the clamp (A) Fig. 3A.

8.

Tip the router so that the bit is clear of the wood surface. Turn the power unit (F) Fig. 3A CLOCKWISE until the index line (D) Fig. 3B on the motor housing reaches the desired depth indicated on the ring.

9. Close the clamp (A) Fig. 3A.

8

F

B

E

D

C

A

Fig. 3A Fig. 3B

NOTE: Setting the index line to 1/4" on the ring means the cutting edge of the bit is exposed 1/4" below the base.

OPERATION

CONNECTING TO POWER SOURCE

Before connecting tool to power source ALWAYS MAKE

SURE SWITCH IS IN THE “OFF” POSITION. Also check that the power circuit is the same as that shown on specification plate of the router.

STARTING AND STOPPING THE MOTOR

Before starting the router, make sure that the bit is clear of the workpiece and foreign objects. Keep a firm grip on router to resist starting torque.

A

Start and stop the motor by setting the toggle switch (A) Fig. 4 to the

“ON” or “OFF” position.

Fig. 4

To avoid personal injury or damage to finished work, always allow the motor to come to a COMPLETE STOP before setting it down.

9

USING THE ROUTER

IMPORTANT: Before using your router, consider the kind and total amount of material to be removed. Depending on the workpiece, more than one cut may be necessary to avoid overloading the motor. Before beginning the cut on the actual workpiece, make a sample cut on a piece of scrap lumber to show exactly how the cut will look, as well as enable you to check dimensions.

Always be sure that the work is rigidly clamped or otherwise secured before making a cut.

Generally speaking, when working on a bench, the workpiece should be held on the bench by wood clamps. When routing edges, the router should be held firmly down and against the work by both guiding knobs.

Since the cutter rotates clockwise

(when viewing router from top), the router should be moved from left to right as you stand facing the work (see

Fig. 5). When working on the inside of a templet, move router in clockwise

Fig. 5

direction. When working on the outside of a templet, move router in a counterclockwise direction.

Avoid “Climb-Cutting” (cutting in direction opposite that shown in Fig. 5). “Climb-Cutting” increases the chance for loss of control resulting in possible personal injury. When

“Climb-Cutting” is required (backing around a corner), exercise extreme caution to maintain control of router.

The speed and depth of cut will depend largely on the type of workpiece.

Keep the cutting pressure constant, but do not crowd the router so the motor speed slows excessively. More than one pass may be necessary on exceptionally hard woods or problem materials to get the desired depth of cut.

When making cuts on all four edges of the workpiece, make the first cut on the end of the piece across the grain. Thus, if chipping of wood occurs at the end of a cut, it will be removed when making the next cut parallel with the grain

.

THE EDGE GUIDE

An optional Edge Guide is available to aid straight edge planing, parallel grooving, and dado or slotting operations.

To assemble, insert guide rods (A) in holes in base Fig. 6 and secure with screws

(B). Adjust the guide (C) on the rods and secure it with thumb screws (D).

TEMPLET GUIDES

A wide variety of templet guides is available for use in pattern and templet routing operations. Fig. 7 shows a typical combination bit, templet guide, and locknut.

DISCONNECT TOOL FROM POWER SOURCE.

10

B

A

D

B

C

Fig. 6

LOCKNUT

ROUTER BIT

Fig. 7

ROUTER

BASE

SUB-BASE

TEMPLET GUIDE

To install, insert templet guide in center hole of router base and secure in place with the locknut.

BEFORE CONNECTING TOOL TO POWER SOURCE, install the bit, adjust the depth of cut, and rotate the router chuck by hand. Make sure that the bit or collet do not contact templet guide.

11

MAINTENANCE

KEEP TOOL CLEAN

Periodically blow out all air passages with dry compressed air. Remove buildup of grime resulting from working with green or sappy wood. All plastic parts should be cleaned with a soft damp cloth. NEVER use solvents to clean plastic parts. They could possibly dissolve or otherwise damage the material.

Wear safety glasses while using compressed air.

FAILURE TO START

Should your tool fail to start, check to make sure the prongs on the cord plug are making good contact in the outlet. Also, check for blown fuses or open circuit breakers in the line.

LUBRICATION

This tool has been lubricated with a sufficient amount of high grade lubricant for the life of the unit under normal operating conditions. No further lubrication is necessary.

BRUSH INSPECTION AND LUBRICATION

For your continued safety and electrical protection, brush inspection and replacement on this tool should ONLY be performed by an AUTHORIZED

PORTER-CABLE SERVICE STATION or a PORTER-CABLE/DELTA FACTORY

SERVICE CENTER.

At approximately 100 hours of use, take or send your tool to your nearest authorized Porter-Cable Service Station to be thoroughly cleaned and inspected. Have worn parts replaced and lubricate with fresh lubricant. Have new brushes installed, and test the tool for performance.

Any loss of power before the above maintenance check may indicate the need for immediate servicing of your tool. DO NOT CONTINUE TO OPERATE TOOL

UNDER THIS CONDITION. If proper operating voltage is present, return your tool to the service station for immediate service.

SERVICE AND REPAIRS

All quality tools will eventually require servicing or replacement of parts due to wear from normal use. These operations, including brush inspection and replacement, should ONLY be performed by either an AUTHORIZED

PORTER-CABLE SERVICE STATION or a PORTER-CABLE/DELTA FACTORY

SERVICE CENTER. All repairs made by these agencies are fully guaranteed against defective material and workmanship. We cannot guarantee repairs made or attempted by anyone other than these agencies.

Should you have any questions about your tool, feel free to write us at any time. In any communications, please give all information shown on the nameplate of your tool (model number, type, serial number, etc.).

12

ACCESSORIES

A complete line of accessories is available from your Porter-Cable

•Delta

Supplier, Porter-Cable

•Delta Factory Service Centers, and Porter-Cable

Authorized Service Stations. Please visit our Web Site

www.portercable.com

supplier.

for a catalog or for the name of your nearest

Since accessories other than those offered by Porter-Cable

Delta have not been tested with this product, use of such accessories could be hazardous. For safest operation, only

Porter-Cable · Delta recommended accessories should be used with this product.

PORTER-CABLE LIMITED

ONE YEAR WARRANTY

Porter-Cable warrants its Professional Power Tools for a period of one year from the date of original purchase. We will repair or replace at our option, any part or parts of the product and accessories covered under this warranty which, after examination, proves to be defective in workmanship or material during the warranty period. For repair or replacement return the complete tool or accessory, transportation prepaid, to your nearest Porter-Cable Service Center or Authorized Service Station.

Proof of purchase may be required. This warranty does not apply to repair or replacement required due to misuse, abuse, normal wear and tear or repairs attempted or made by other than our Service

Centers or Authorized Service Stations.

ANY IMPLIED WARRANTY, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND

FITNESS FOR A PARTICULAR PURPOSE, WILL LAST ONLY FOR ONE (1) YEAR FROM THE DATE

OF PURCHASE.

To obtain information on warranty performance please write to: PORTER-CABLE CORPORATION,

4825 Highway 45 North, Jackson, Tennessee 38305; Attention: Product Service. THE FOREGOING

OBLIGATION IS PORTER-CABLE’S SOLE LIABILITY UNDER THIS OR ANY IMPLIED WARRANTY

AND UNDER NO CIRCUMSTANCES SHALL PORTER-CABLE BE LIABLE FOR ANY INCIDENTAL OR

CONSEQUENTIAL DAMAGES. Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.

This warranty gives you specific legal rights and you may also have other legal rights which vary from state to state.

13

NOTES

14

PORTER-CABLE • DELTA SERVICE CENTERS

(CENTROS DE SERVICIO DE PORTER-CABLE • DELTA)

(CENTRE DE SERVICE PORTER-CABLE • DELTA)

Parts and Repair Service for Porter-Cable • Delta Power Tools are Available at These Locations

(Obtenga Refaccion de Partes o Servicio para su Herramienta en los Siguientes Centros de Porter-Cable • Delta)

(Locations où vous trouverez les pièces de rechange nécessaires ainsi qu’un service d’entretien)

ARIZONA

Tempe 85282 (Phoenix)

2400 West Southern Avenue

Suite 105

Phone: (602) 437-1200

Fax: (602) 437-2200

GEORGIA

Forest Park 30297 (Atlanta)

5442 Frontage Road,

Suite 112

Phone: (404) 608-0006

Fax: (404) 608-1123

MINNESOTA

Minneapolis 55429

5522 Lakeland Avenue North

Phone: (763) 561-9080

Fax: (763) 561-0653

Cleveland 44125

8001 Sweet Valley Drive

Unit #19

Phone: (216) 447-9030

Fax: (216) 447-3097

CALIFORNIA

Ontario 91761 (Los Angeles)

3949A East Guasti Road

Phone: (909) 390-5555

Fax: (909) 390-5554

San Diego 92111

7638 Clairemnot Blvd.

Phone: (858) 277-9595

Fax: (858) 277-9696

San Leandro 94577 (Oakland)

3039 Teagarden Street

Phone: (510) 357-9762

Fax: (510) 357-7939

COLORADO

Arvada 80003 (Denver)

8175 Sheridan Blvd., Unit S

Phone: (303) 487-1809

Fax: (303) 487-1868

ILLINOIS

Addison 60101 (Chicago)

400 South Rohlwing Rd.

Phone: (630) 424-8805

Fax: (630) 424-8895

Woodridge 60517 (Chicago)

2033 West 75th Street

Phone: (630) 910-9200

Fax: (630) 910-0360

MARYLAND

Elkridge 21075 (Baltimore)

7397-102 Washington Blvd.

Phone: (410) 799-9394

Fax: (410) 799-9398

MASSACHUSETTS

Franklin 02038 (Boston)

Franklin Industrial Park

101E Constitution Blvd.

Phone: (508) 520-8802

Fax: (508) 528-8089

MISSOURI

North Kansas City 64116

1141 Swift Avenue

Phone: (816) 221-2070

Fax: (816) 221-2897

St. Louis 63119

7574 Watson Road

Phone: (314) 968-8950

Fax: (314) 968-2790

NEW YORK

Flushing 11365-1595 (N.Y.C.)

175-25 Horace Harding Expwy.

Phone: (718) 225-2040

Fax: (718) 423-9619

NORTH CAROLINA

Charlotte 28270

9129 Monroe Road, Suite 115

Phone: (704) 841-1176

Fax: (704) 708-4625

OREGON

Portland 97230

4916 NE 122 nd Ave.

Phone: (503) 252-0107

Fax: (503) 252-2123

PENNSYLVANIA

Willow Grove 19090 (Philadelphia)

520 North York Road

Phone: (215) 658-1430

Fax: (215) 658-1433

TEXAS

Carrollton 75006 (Dallas)

1300 Interstate 35 N, Suite 112

Phone: (972) 446-2996

Fax: (972) 446-8157

Houston 77043

4321 Sam Houston Parkway, West

Suite 180

Phone: (713) 983-9910

Fax: (713) 983-6645

FLORIDA

Davie 33314 (Miami)

4343 South State Rd. 7 (441)

Unit #107

Phone: (954) 321-6635

Fax: (954) 321-6638

MICHIGAN

Madison Heights 48071 (Detroit)

30475 Stephenson Highway

Phone: (248) 597-5000

Fax: (248) 597-5004

OHIO

Columbus 43214

4560 Indianola Avenue

Phone: (614) 263-0929

Fax: (614) 263-1238

WASHINGTON

Auburn 98001(Seattle)

3320 West Valley HWY, North

Building D, Suite 111

Phone: (253) 333-8353

Fax: (253) 333-9613

Tampa 33609

4538 W. Kennedy Boulevard

Phone: (813) 877-9585

Fax: (813) 289-7948

Authorized Service Stations are located in many large cities. Telephone 800-487-8665 or 731-541-6042 for assistance locating one. Parts and accessories for Porter-Cable • Delta products should be obtained by contacting any Porter-Cable • Delta Distributor, Authorized Service Center, or Porter-Cable • Delta Factory Service Center. If you do not have access to any of these, call 888-848-5175 and you will be directed to the nearest Porter-Cable • Delta Factory Service Center. Las Estaciones de Servicio Autorizadas están ubicadas en muchas grandes ciudades. Llame al 800-487-8665 ó al 731-541-6042 para obtener asistencia a fin de localizar una. Las piezas y los accesorios para los productos Porter-Cable

• Delta deben obtenerse poniéndose en contacto con cualquier distribuidor Porter-Cable • Delta, Centro de Servicio Autorizado o Centro de

Servicio de Fábrica Porter-Cable • Delta. Si no tiene acceso a ninguna de estas opciones, llame al 888-848-5175 y le dirigirán al Centro de

Servicio de Fábrica Porter-Cable • Delta más cercano. Des centres de service agréés sont situés dans beaucoup de grandes villes. Appelez au

800-487-8665 ou au 731-541-6042 pour obtenir de l’aide pour en repérer un. Pour obtenir des pièces et accessoires pour les produits Porter-

Cable • Delta, s’adresser à tout distributeur Porter-Cable • Delta, centre de service agréé ou centre de service d’usine Porter-Cable • Delta. Si vous n’avez accès à aucun de ces centres, appeler le 888-848-5175 et on vous dirigera vers le centre de service d’usine Porter-Cable • Delta le plus proche.

CANADIAN PORTER-CABLE • DELTA SERVICE CENTERS

ALBERTA

Bay 6, 2520-23rd St. N.E.

MANITOBA

1699 Dublin Avenue

QUÉBEC

1515 Ave.

Calgary, Alberta

T2E 8L2

Winnipeg, Manitoba

R3H 0H2

St-Jean Baptiste, Suite 160

Québec, P.Q.

Phone: (403) 735-6166

Fax: (403) 735-6144

Phone: (204) 633-9259

Fax: (204) 632-1976

G2E 5E2

Phone: (418) 877-7112

Fax: (418) 877-7123

BRITISH COLUMBIA

8520 Baxter Place

Burnaby, B.C.

V5A 4T8

Phone: (604) 420-0102

Fax: (604) 420-3522

ONTARIO

505 Southgate Drive

Guelph, Ontario

N1H 6M7

Phone: (519) 767-4132

Fax: (519) 767-4131

1447, Begin

St-Laurent, (Mtl), P.Q.

H4R 1V8

Phone: (514) 336-8772

Fax: (514) 336-3505

The following are trademarks of PORTER-CABLE • DELTA (Las siguientes son marcas registradas de PORTER-CABLE • DELTA S.A.) (Les marques suivantes sont des marques de fabriquant de la PORTER-CABLE • DELTA): Auto-Set ® , BAMMER ® , B.O.S.S.

® , Builder’s Saw ® , Contractor’s Saw ® ,

Contractor’s Saw II™, Delta ® , DELTACRAFT ® , DELTAGRAM™, Delta Series 2000™, DURATRONIC™, Emc²™, FLEX ® , Flying Chips™, FRAME

SAW ® , Grip Vac™, Homecraft ® , INNOVATION THAT WORKS

LATHE ® , MORTEN™, NETWORK™, OMNIJIG ®

® , Jet-Lock ® , JETSTREAM

, POCKET CUTTER ® , PORTA-BAND ®

® , ‘kickstand ® , LASERLOC

, PORTA-PLANE ®

® , MICRO-SET ® , Micro-Set ® , MIDI

, PORTER-CABLE ® &(design), PORTER-

CABLE ® PROFESSIONAL POWER TOOLS, PORTER-CABLE REDEFINING PERFORMANCE™, Posi-Matic ® , Q-3 ® &(design), QUICKSAND ® &(design),

QUICKSET™, QUICKSET II ® , QUICKSET PLUS™, RIPTIDE™&(design), SAFE GUARD II ® , SAFE-LOC ® , Sanding Center ® , SANDTRAP ® &(design),

SAW BOSS ® , Sawbuck™, Sidekick ® , SPEED-BLOC ® , SPEEDMATIC

Lumber Company ® &(design), THE PROFESSIONAL EDGE ®

® , SPEEDTRONIC ® , STAIR EASE

, THE PROFESSIONAL SELECT ®

® , The American Woodshop ® &(design), The

, THIN-LINE™, TIGER ® , TIGER CUB ® , TIGER SAW ® ,

TORQBUSTER ® , TORQ-BUSTER ® , TRU-MATCH™, TWIN-LITE ® , UNIGUARD ® , Unifence ® , UNIFEEDER™, Unihead ® , Uniplane™, Unirip ® , Unisaw ® ,

Univise ® , Versa-Feeder ® , VERSA-PLANE ® , WHISPER SERIES ® ,

WOODWORKER’S CHOICE™.

Trademarks noted with ™ and ® are registered in the United States Patent and Trademark Office and may also be registered in other countries.

Las Marcas Registradas con el signo de ™ y ® son registradas por la Oficina de Registros y Patentes de los Estados Unidos y también pueden estar registradas en otros países. Marques déposées, indiquées par la lettre ™ et ®, sont déposées au Bureau des brevets d’invention et marques déposées aux Etats-Unis et pourraient être déposées aux autres pays.

Printed in U.S.A. PC-0104-150