Poulan 545154719 Trimmer Instruction manual

R

Please do not return unit to retailer.

Por favor, no devuelva el aparato al lugar de compra.

Veuillez ne pas retourner l’outil au détaillant.

1-800-554-6723 www.poulan.com

Instruction Manual

Manual de Instrucciones

Manuel d’Instructions

P4500

For Occasional Use Only

WARNING:

Read and follow all Safety Rules and Operating Instructions before using this product. Failure to do so can result in serious injury.

ADVERTENCIA:

Lea el manual de instrucciones y siga todas las advertencias e instrucciones de seguridad. El no hacerlo puede resultar en lesiones graves.

AVERTISSEMENT:

Lire le manuel d’instructions et bien respecter tous les avertissements et toutes les instructions de sécurité. Tout défaut de le faire pourrait entraîner des blessures graves.

Poulan

1030 Stevens Creek Road

Augusta, GA 30907

Poulan

5855 Terry Fox Way

Mississauga, Ontario L5V 3E4

545154719 Rev. 1 11/01/07 BRW

IDENTIFICATION OF SAFETY SYMBOLS

DANGER: Use only specified trimmer head, spool, and 0.080 inch (2 mm) recommended trimmer line. Never use blades, flailing devices, wire, rope, string, etc. Unit is designed for line trimmer use only. Failure to follow these instructions may result in serious injury.

WARNING: This unit can be dangerous! Careless or improper use can cause serious injury.

Read the operator’s manual before use. Failure to follow instructions could result in serious injury. Save operator’s manual.

Hazard zone for thrown objects.

S Trimmer line throws objects violently.

S You and others can be blinded/injured.

S Keep children, bystanders, and animals

50 feet (15 meters) away.

Trimmer line can throw objects violently.

You can be blinded or injured. Always wear hearing protection and safety glasses marked Z87. Always wear heavy, long pants, long sleeves, boots and gloves.

Secure hair above shoulder length.

Do not wear jewelry, loose clothing, or clothing with loosing hanging straps, ties, tassels, etc. They can be caught in moving parts.

Never allow children to operate this unit.

2

IDENTIFICATION OF SAFETY SYMBOLS

Store unit indoors in a high, dry place out of the reach of children.

When servicing unit, use only identical replacement parts.

Always stop unit and disconnect spark plug before cleaning or servicing.

WARNING: Fire hazard. Never mix, pour, or store gasoline or use the unit near a flame or sparks (including smoking, open flames, or work that can cause sparks).

Use unleaded gasoline and two--stroke oil mixed at a ratio of

40:1 (2.5%).

SAFETY RULES

WARNING: When using gardening appliances, basic safety precautions must always be followed to reduce the risk of fire and serious injury. Read and follow all instructions.

This power unit can be dangerous! Operator is responsible for following instructions and warnings on unit and in manual. Read entire instruction manual before using unit! Be thoroughly familiar with the controls and the proper use of the unit. Restrict the use of this unit to persons who have read, understand, and will follow the instructions and warnings on the unit and in the manual. Never allow children to operate this unit.

INSTRUCTION

MANUAL

SAFETY INFORMATION ON THE UNIT

DANGER: Never use blades or flailing devices. This unit is designed for line trimmer use only. Use of any other accessories or attachments will increase the risk of injury.

WARNING: Trimmer line throws objects violently. You and others can be blinded/injured. Wear eye and leg protection. Keep body parts clear of rotating line.

Eye Protection

HazardZone

50 ft.

(15 m)

Boots

3

Keep children, bystanders, and animals 50 feet

(15 meters) away. Stop unit immediately if approached.

If situations occur which are not covered in this manual, use care and good judgment. If you need assistance, contact your authorized service dealer or call 1--800--554--6723.

OPERATOR SAFETY

S

Dress properly.

Always wear safety glasses or similar eye protection when operating, or performing maintenance, on your unit (safety glasses are available).

Eye protection should be marked Z87.

S Always wear face or dust mask if operation is dusty.

S Always wear heavy, long pants, long sleeves, boots, and gloves. Wearing safety leg guards is recommended.

S

Always wear foot protection. Do not go barefoot or wear sandals. Stay clear of spinning line.

S Secure hair above shoulder length. Secure or remove loose clothing or clothing with loosely hanging ties, straps, tassels, etc.

They can be caught in moving parts.

S

Being fully covered also helps protect you from debris and pieces of toxic plants thrown by spinning line.

S Stay alert. Do not operate this unit when you are tired, ill, upset or under the influence of alcohol, drugs, or medication. Watch what you are doing; use common sense.

S

Wear hearing protection.

S

Never start or run inside a closed room or building. Breathing exhaust fumes can kill.

S

Keep handles free of oil and fuel.

UNIT / MAINTENANCE SAFETY

S Disconnect the spark plug before performing maintenance except carburetor adjustments.

S

Look for and replace damaged or loose parts before each use. Look for and repair fuel leaks before use. Keep in good working condition.

S Replace trimmer head parts that are chipped, cracked, broken, or damaged in any other way before using the unit.

S Maintain unit according to recommended procedures. Keep cutting line at proper length.

S

Use only 0.080 inch (2 mm) diameter Poulan/

WEED EATER brand replacement line. Never use wire, rope, string, etc.

S Install required shield properly before using the unit. Use only specified trimmer head; make sure it is properly installed and securely fastened.

S Make sure unit is assembled correctly as shown in this manual.

S

Make carburetor adjustments with lower end supported to prevent line from contacting any object.

S Keep others away when making carburetor adjustments.

S Use only recommended Poulan/WEED

EATER accessories and replacement parts.

S

Have all maintenance and service not explained in this manual performed by an authorized service dealer.

FUEL SAFETY

S Mix and pour fuel outdoors.

S

Keep away from sparks or flames.

S Use a container approved for fuel.

S

Do not smoke or allow smoking near fuel or the unit.

S Avoid spilling fuel or oil. Wipe up all fuel spills.

4

S Move at least 10 feet (3 meters) away from fueling site before starting engine.

S Stop engine and allow to cool before removing fuel cap.

S

Always store gasoline in a container approved for flammable liquids.

CUTTING SAFETY

WARNING: Inspect the area before each use. Remove objects (rocks, broken glass, nails, wire, etc.) which can be thrown by or become entangled in line. Hard objects can damage the trimmer head and be thrown causing serious injury.

S

Use only for trimming, scalping, mowing and sweeping. Do not use for edging, pruning or hedge trimming.

S

Keep firm footing and balance. Do not overreach.

S Keep all parts of your body away from muffler and spinning line. Keep engine below waist level. A hot muffler can cause serious burns.

S

Cut from your left to your right. Cutting on right side of the shield will throw debris away from the operator.

S

Use only in daylight or good artificial light.

S Use only for jobs explained in this manual.

TRANSPORTING AND STORAGE

S

Allow engine to cool before storing or transporting in vehicle.

S

Empty the fuel tank before storing or transporting the unit. Use up fuel left in the carburetor by starting the engine and letting it run until it stops.

S Store unit and fuel in area where fuel vapors cannot reach sparks or open flames from water heaters, electric motors or switches, furnaces, etc.

S Store unit so line limiter blade cannot accidentally cause injury. The unit can be hung by the shaft.

S Store unit out of reach of children.

WARNING: The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm.

SAFETY NOTICE:

Exposure to vibrations through prolonged use of gasoline powered hand tools could cause blood vessel or nerve damage in the fingers, hands, and joints of people prone to circulation disorders or abnormal swellings. Prolonged use in cold weather has been linked to blood vessel damage in otherwise healthy people. If symptoms occur such as numbness, pain, loss of strength, change in skin color or texture, or loss of feeling in the fingers, hands, or joints, discontinue the use of this tool and seek medical attention. An anti--vibration system does not guarantee the avoidance of these problems. Users who operate power tools on a continual and regular basis must monitor closely their physical condition and the condition of this tool.

SPECIAL NOTICE:

This unit is equipped with a temperature limiting muffler and spark arresting screen which meets the requirements of

California Codes 4442 and 4443. All U.S. forest land and the states of California, Idaho, Maine,

Minnesota, New Jersey, Oregon, and Washington require by law that many internal combustion engines be equipped with a spark arresting screen. If you operate in a locale where such regulations exist, you are legally responsible for maintaining the operating condition of these parts. Failure to do so is a violation of the law.

For normal homeowner use, the muffler and spark arresting screen will not require any service. After 50 hours of use, we recommend that your muffler be serviced or replaced by an authorized service dealer.

ASSEMBLY

ATTACHING SHIELD

WARNING: If received assembled, repeat all steps to ensure your unit is properly assembled and all fasteners are secure.

Examine parts for damage. Do not use damaged parts.

NOTE:

If you need assistance or find parts missing or damaged, call 1-800-554-6723.

It is normal for the fuel filter to rattle in the empty fuel tank.

Finding fuel or oil residue on muffler is normal due to carburetor adjustments and testing done by the manufacturer.

ADJUSTING THE HANDLE

WARNING: When adjusting the assist handle, be sure it remains above the safety label and below the mark or arrow on the shaft.

1. Loosen wing nut on handle.

2. Rotate the handle on the shaft to an upright position; retighten wing nut.

WARNING: The shield must be properly installed. The shield provides partial protection to the operator and others from the risk of thrown objects, and is equipped with a line limiter blade which cuts excess line to the proper length. The line limiter blade (on underside of shield) is sharp and can cut you.

For proper orientation of shield, see KNOW

YOUR TRIMMER illustration in OPERATION section.

1. Remove wing nut from shield.

2. Insert bracket into slot as shown.

3. Pivot shield until bolt passes through hole in bracket.

4. Securely tighten wing nut onto bolt.

Slot Wing Nut

Shield

Bracket

Gearbox

PIVOT

5

OPERATION

KNOW YOUR TRIMMER

READ THIS INSTRUCTION MANUAL AND SAFETY RULES BEFORE OPERATING YOUR UNIT.

Compare the illustrations with your unit to familiarize yourself with the location of the various controls and adjustments. Save this manual for future reference.

Trimmer

Head

Shaft

Safety Label

Assist Handle

Shaft Mark or Arrow

Muffler

Shield

Spark Plug

Primer Bulb Throttle Trigger

Line Limiter Blade

STOP

Switch

Fuel Mix Fill Cap

Starter Handle

Choke Lever

STOP SWITCH

The STOP switch is used to stop the engine. To stop the engine, push and hold the switch in the

STOP position until the engine stops.

PRIMER BULB

The PRIMER BULB removes air from the carburetor and fuel lines and fills them with fuel.

This allows you to start the engine with fewer pulls on the starter rope. Activate the primer bulb by pressing it and allowing it to return to its original form.

BEFORE STARTING ENGINE

WARNING: Be sure to read the fuel information in the safety rules before you begin. If you do not understand the safety rules, do not attempt to fuel your unit. Call

1-800-554--6723.

FUELING ENGINE

WARNING: Remove fuel cap slowly when refueling.

HELPFUL TIP

To obtain the correct oil mix ratio, pour 3.2 ounces of

2--cycle synthetic oil into one gallon of fresh gas.

This engine is certified to operate on unleaded gasoline. Before operation, gasoline must be mixed with a good quality synthetic 2-cycle air-cooled engine oil designed to be mixed at a ratio of 40:1. Poulan/WEED EATER brand synthetic oil is recommended. Mix gasoline and oil at a ratio of 40:1. A 40:1 ratio is obtained by

CHOKE

The CHOKE helps to supply fuel to the engine to aid in cold starting. Activate the choke by moving the choke lever to the FULL CHOKE position. After the engine attempts to start, move the choke lever to the HALF CHOKE position.

Once engine has started, move the choke lever to the RUN position.

mixing 3.2 ounces (95 ml) of oil with 1 gallon (4 liters) of unleaded gasoline. DO NOT USE automotive oil or marine oil. These oils will cause engine damage. When mixing fuel, follow instructions printed on container. Once oil is added to gasoline, shake container momentarily to assure that the fuel is thoroughly mixed.

Always read and follow the safety rules relating to fuel before fueling your unit.

6

IMPORTANT

Experience indicates that alcohol blended fuels

(called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage.

Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, empty the fuel system before storage for 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season. Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur. See the STORAGE section for additional information.

HELPFUL TIP

If your engine switch reads

“push to stop”, it is always in the ON position.

HOW TO STOP YOUR UNIT

S

To stop the engine, push and hold the STOP switch in the STOP position until the engine stops.

S

If engine does not stop, move choke lever to FULL CHOKE position.

HOW TO START YOUR UNIT

WARNING: The trimmer head will turn while starting the engine. Avoid any contact with the muffler. A hot muffler can cause serious burns.

HELPFUL TIP

If your engine still does not start after following these instructions, please call

1--800--554--6723.

STARTING A COLD ENGINE (or a warm engine after running out of fuel)

Starting Position

1. Set unit on a flat surface.

2. Slowly press the primer bulb 6 times.

3. Move choke lever to the FULL CHOKE position.

4. Squeeze the throttle trigger fully and hold through all remaining steps.

Primer Bulb

5. Pull starter rope handle sharply until engine sounds as if it is trying to start, but do not pull rope more than 6 times.

6. As soon as engine sounds as if it is trying to start, move choke lever to HALF CHOKE position.

7. Pull starter rope sharply until engine runs, but no more than 6 pulls.

NOTE:

If the engine doesn’t start after 6 pulls (at the HALF CHOKE position), move the choke lever to the FULL

CHOKE position and press the primer bulb 6 times. Squeeze and hold the throttle trigger and pull the starter rope 2 more times. Move the choke lever to the

HALF CHOKE position and pull the starter rope until the engine runs, but no more than 6 pulls. If the engine still doesn’t start, it is probably flooded. Proceed to

STARTING A FLOODED ENGINE.

8. Once the engine starts, allow it to run 10 seconds, then move the choke lever to the

RUN position. Allow the unit to run for 30 more seconds at RUN before releasing the throttle trigger.

NOTE:

If engine dies with the choke lever in the RUN position, move the choke lever to the HALF CHOKE position and pull the rope until engine runs, but no more than 6 pulls.

STARTING A WARM ENGINE

1. Move the choke lever to the HALF

CHOKE position.

2. Squeeze and hold the throttle trigger.

Keep throttle trigger fully squeezed until the engine runs smoothly.

3. Pull starter rope sharply until engine runs, but no more than 6 pulls.

4. Allow engine to run 15 seconds, then move the choke lever to the RUN position.

NOTE:

If engine has not started, pull starter rope 5 more pulls. If engine still does not run, it is probably flooded.

STARTING A FLOODED ENGINE

Flooded engines can be started by placing the choke lever in the RUN position; then, pull the rope to clear the engine of excess fuel.

This could require pulling the starter handle many times depending on how badly the unit is flooded. If the unit still doesn’t start, refer to

TROUBLESHOOTING TABLE or call

1-800-554--6723.

Choke

Lever

Starter Handle

7

OPERATING INSTRUCTIONS

It is recommended that the engine not be operated for longer than 1 minute at full throttle.

OPERATING POSITION

ALWAYS WEAR:

Long pants

Heavy shoes

Eye protection advance properly and can cause serious injury. Do not use other materials such as wire, string, rope, etc. Wire can break off during cutting and become a dangerous missile that can cause serious injury.

CUTTING METHODS

WARNING: Use minimum speed and do not crowd the line when cutting around hard objects (rock, gravel, fence posts, etc.), which can damage the trimmer head, become entangled in the line, or be thrown causing a serious hazard.

S The tip of the line does the cutting. You will achieve the best performance and minimum line wear by not crowding the line into the cutting area. The right and wrong ways are shown below.

Tip of line does the cutting.

Line crowded into work area.

Cut from your left to your right.

WARNING: Always wear eye protection. Never lean over the trimmer head.

Rocks or debris can ricochet or be thrown into eyes and face and cause blindness or other serious injury.

Do not run the engine at a higher speed than necessary. The cutting line will cut efficiently when the engine is run at less than full throttle.

At lower speeds, there is less engine noise and vibration. The cutting line will last longer and will be less likely to “weld” onto the spool.

Always release the throttle trigger and allow the engine to return to idle speed when not cutting.

To stop engine:

S Release the throttle trigger.

S Push and hold the STOP switch in the

STOP position until the engine stops.

TRIMMER LINE ADVANCE

The trimmer line will advance approximately 2 inches (5 cm) each time the bottom of the trimmer head is tapped on the ground with the engine running at full throttle.

The most efficient line length is the maximum length allowed by the line limiter.Always keep the shield in place when the tool is being operated.

To advance line:

S Operate the engine at full throttle.

S Hold the trimmer head parallel to and above the grassy area.

S

Tap the bottom of the trimmer head lightly on the ground one time. Approximately 2 inches

(5 cm) of line will be advanced with each tap.

Always tap the trimmer head on a grassy area.

Tapping on surfaces such as concrete or asphalt can cause excessive wear to the trimmer head. If the line is worn down to 2 inches (5 cm) or less, more than one tap will be required to obtain the most efficient line length.

WARNING: Use only 0.080 inch (2 mm) diameter line. Other sizes of line will not

Right Wrong

S The line will easily remove grass and weeds from around walls, fences, trees and flower beds, but it also can cut the tender bark of trees or shrubs and scar fences.

S

For trimming or scalping, use less than full throttle to increase line life and decrease head wear, especially:

S During light duty cutting.

S Near objects around which the line can wrap such as small posts, trees or fence wire.

S

For mowing or sweeping, use full throttle for a good clean job.

TRIMMING -- Hold the bottom of the trimmer head about 3 inches (8 cm) above the ground and at an angle. Allow only the tip of the line to make contact. Do not force trimmer line into work area.

Trimming

3 inches (8 cm) above ground

8

SCALPING -- The scalping technique removes unwanted vegetation. Hold the bottom of the trimmer head about 3 inches (8 cm) above the ground and at an angle. Allow the tip of the line to strike the ground around trees, posts, monuments, etc. This technique increases line wear.

MOWING -- Your trimmer is ideal for mowing in places conventional lawn mowers cannot reach. In the mowing position, keep the line parallel to the ground. Avoid pressing the head into the ground as this can scalp the ground and damage the tool.

SWEEPING -- The fanning action of the rotating line can be used for a quick and easy clean up. Keep the line parallel to and above the surfaces being swept and move the tool from side to side.

WARNING: Disconnect the spark plug before performing maintenance except for carburetor adjustments.

HELPFUL TIP

IMPORTANT:

Have all repairs other than the recommended maintenance described in the instruction manual performed by an authorized service dealer.

If any dealer other than an authorized service dealer performs work on the product, Electrolux Home Products,

Inc., may not pay for repairs under warranty. It is your responsibility to maintain and perform general maintenance.

CHECK FOR LOOSE

FASTENERS AND PARTS

S

Spark Plug Boot

S

Air Filter

S

Housing Screws

S Assist Handle Screw

S Debris Shield

CHECK FOR DAMAGED OR

WORN PARTS

Contact an authorized service dealer for replacement of damaged or worn parts.

S

STOP Switch -- Ensure STOP switch functions properly by pushing and holding the switch in the STOP position. Make sure engine stops. Restart engine and continue.

MAINTENANCE

S Fuel Tank -- Discontinue use of unit if fuel tank shows signs of damage or leaks.

S Debris Shield -- Discontinue use of unit if debris shield is damaged.

INSPECT AND CLEAN UNIT AND DE-

CALS

S

After each use, inspect complete unit for loose or damaged parts. Clean the unit and decals using a damp cloth with a mild detergent.

S Wipe off unit with a clean dry cloth.

CLEAN AIR FILTER

A dirty air filter decreases engine performance and increases fuel consumption and harmful emissions. Always clean after every

5 hours of operation.

1. Clean the air filter cover and the area around it to keep dirt from falling into the carburetor chamber when the cover is opened.

2. Open air filter cover by pushing button

(see illustration). Remove air filter.

NOTE:

To avoid creating a fire hazard or producing harmful evaporative emissions, do not clean filter in gasoline or other flammable solvent.

3. Wash the filter in soap and water.

4. Allow filter to dry.

5. Replace air filter and close cover.

9

Button

Air Filter

Air Filter Cover

As your unit is used, carbon deposits build up on the muffler and spark arresting screen.

For normal homeowner use, however, the muffler and spark arresting screen will not require any service. After 50 hours of use, we recommend that your muffler be serviced or replaced by your authorized service dealer.

REPLACE SPARK PLUG

Replace the spark plug each year to ensure the engine starts easier and runs better. Set spark plug gap at 0.025 inch (0.6 mm). Ignition timing is fixed and nonadjustable.

1. Twist, then pull off spark plug boot.

2. Remove spark plug from cylinder and discard.

3. Replace with Champion RCJ-6Y spark plug and tighten securely with a 3/4 inch

(19 mm) socket wrench.

4. Reinstall the spark plug boot.

MUFFLER AND SPARK ARREST-

ING SCREEN

WARNING: The muffler on this product contains chemicals known to the State of

California to cause cancer.

SERVICE AND ADJUSTMENTS

REPLACING THE LINE

1. Press the tabs on the side of the trimmer head and remove cover and spool.

7. With your finger between the lines, wrap the lines evenly and firmly around the spool in a clockwise direction.

8. Position the lines in the guide slots.

Tap Button

2. Remove any remaining line.

3. Clean dirt and debris from all parts. Replace spool if it is worn or damaged.

4. Replace with a pre-wound spool, or replace line using a 25 feet (8 meters) length of 0.080 inch (2 mm) diameter

Poulan/WEED EATER brand line.

5. When installing new line on an existing spool, hold the spool as shown in the illustration below.

6. Bend the line at the midpoint and insert the bend into the slot in the center rim of the spool. Ensure line snaps into position in the slot.

Slot

Cover

Tab

Guide Slot

9. Insert the ends of the lines through exit holes in the sides of the cover.

10. Place the spool in the cover.

Spool

Guide

Slot

Spool

Cover

11. Make sure the lines are not caught between the rim of the spool and the wall of the cover.

12. Reinstall the spool and cover onto the trimmer head. Push until cover snaps into place.

10

REPLACING THE CUTTING HEAD

1. Align hole in the dust cup with the hole in the side of the gearbox by rotating the dust cup.

2. Insert a small screwdriver into aligned holes. This will keep the shaft from turning while removing and installing trimmer head.

Screwdriver will not make contact with any object. Hold the unit by hand while running and making adjustments. Keep all parts of your body away from the cutting attachment and muffler.

Idle Speed Adjustment

Allow engine to idle. Adjust speed until engine runs without stalling (idle speed too slow).

S

Turn idle speed screw clockwise to increase engine speed if engine stalls or dies.

S Turn idle speed screw counterclockwise to decrease engine speed.

Idle Speed Screw

3. While holding the screwdriver in position, remove trimmer head by turning clockwise.

4. Thread replacement trimmer head onto the shaft by turning counterclockwise.

Tighten until secure.

5. Remove the screwdriver.

CARBURETOR ADJUSTMENT

WARNING: Keep others away when making idle speed adjustments. The trimmer head will be spinning during this procedure.

Wear your protective equipment and observe all safety precautions.

The carburetor has been carefully set at the factory. Adjustments may be necessary if you notice any of the following conditions:

S Engine will not idle when the throttle is released.

Make adjustments with the unit supported so the cutting attachment is off the ground and

Air Filter Cover

If you require further assistance or are unsure about performing this procedure, contact an authorized service dealer or call

1--800--554--6723.

WARNING: Perform the following steps after each use:

S Allow engine to cool before storing or transporting.

S

Store unit and fuel in a well ventilated area where fuel vapors cannot reach sparks or open flames from water heaters, electric motors or switches, furnaces, etc.

S Store unit with all guards in place. Position unit so that any sharp object cannot accidentally cause injury.

S Store unit and fuel well out of the reach of children.

SEASONAL STORAGE

Prepare unit for storage at end of season or if it will not be used for 30 days or more.

If your unit is to be stored for a period of time:

S Clean the entire unit before lengthy storage.

S

Store in a clean dry area.

S

Lightly oil external metal surfaces.

FUEL SYSTEM

Under FUELING ENGINE in the OPERA-

TION section of this manual, see message labeled IMPORTANT regarding the use of gasohol in your engine.

Fuel stabilizer is an acceptable alternative in minimizing the formation of fuel gum deposits during storage. Add stabilizer to the gasoline in the fuel tank or fuel storage container. Fol-

STORAGE

low the mix instructions found on stabilizer container. Run engine at least 5 minutes after adding stabilizer.

HELPFUL TIP

During storage of your gas/ oil mixture, the oil will separate from the gas.

We recommend that you shake the gas can weekly to insure proper blending of the gas and oil.

ENGINE

S

Remove spark plug and pour 1 teaspoon of

40:1, 2-cycle engine oil (air cooled) through the spark plug opening. Slowly pull the starter rope 8 to 10 times to distribute oil.

S Replace spark plug with new one of recommended type and heat range.

S Clean air filter.

S

Check entire unit for loose screws, nuts, and bolts. Replace any damaged, broken, or worn parts.

S At the beginning of the next season, use only fresh fuel having the proper gasoline to oil ratio.

OTHER

S

Do not store gasoline from one season to another.

S

Replace your gasoline can if it starts to rust.

11

TROUBLESHOOTING TABLE

WARNING: Always stop unit and disconnect spark plug before performing all of the recommended remedies below except remedies that require operation of the unit.

TROUBLE

Engine will not start.

CAUSE

1. Engine flooded.

2. Fuel tank empty.

3. Spark plug not firing.

4. Fuel not reaching carburetor.

REMEDY

1. See “Starting a Flooded Engine” in

Operation Section.

2. Fill tank with correct fuel mixture.

3. Install new spark plug.

4. Check for dirty fuel filter; replace.

Check for kinked or split fuel line; repair or replace.

5. Contact an authorized service dealer.

Engine will not idle properly.

Engine will not accelerate, lacks power, or dies under a load.

5. Carburetor requires adjustment.


2. Crankshaft seals worn.

3. Compression low.

1. Air filter dirty.

2. Spark plug fouled.

1. See “Carburetor Adjustment” in

Service and Adjustments Section.



1. Clean or replace air filter.

2. Clean or replace plug and regap.


Engine smokes excessively.

Engine runs hot.


4. Carbon build-up on muffler outlet screen.

5. Compression low.

1. Choke partially on.

2. Fuel mixture incorrect.

3. Air filter dirty.


1. Fuel mixture incorrect.

2. Spark plug incorrect.


4. Carbon build-up on muffler outlet screen.



1. Adjust choke.

2. Empty fuel tank and refill with correct fuel mixture.

3. Clean or replace air filter.


1. See “Fueling Engine” in Operation section.

2. Replace with correct spark plug.



12

LIMITED WARRANTY

Poulan, a division of Husqvarna Outdoor Products Inc., warrants to the original consumer purchaser that each new Poulan brand gasoline tool or attachment is free from defects in material and workmanship and agrees to repair or replace under this warranty any defective gasoline product or attachment as follows from the original date of purchase.

2 YEARS -- Parts and Labor, when used for household purposes.

90 DAYS -- Parts and Labor, when used for commercial, professional, or income producing purposes.

30 DAYS -- Parts and Labor, if used for rental purposes.

This warranty is not transferable and does not cover damage or liability caused by improper handling, improper maintenance or alteration, or the use of accessories and/or attachments not specifically recommended by Poulan for this tool. This warranty does not cover tune--up, spark plugs, filters, starter ropes, starter springs, cutting line, or rotating head parts that will wear and require replacement with reasonable use during the warranty period. This warranty does not cover pre--delivery setup or normal adjustments explained in the instruction manual. This warranty does not cover transportation costs.

In the event you have a claim under this warranty, you must return the product to an authorized service dealer.

Should you have any unanswered questions concerning this warranty, please contact:

Poulan, a division of

Husqvarna Outdoor Products Inc.

1030 Stevens Creek Road

Augusta, GA 30907

1--800--554--6723

In Canada, contact:

Poulan

5855 Terry Fox Way

Mississauga,Ontario L5V3E4

Giving the model number, serial number and date of purchase of your product and the name and address of the authorized dealer from whom it was purchased.

THIS WARRANTY GIVES YOU SPECIFIC

LEGAL RIGHTS, AND YOU MAY HAVE OTH-

ER RIGHTS WHICH VARY FROM STATE TO

STATE.

NO CLAIMS FOR CONSEQUENTIAL OR

OTHER DAMAGES WILL BE ALLOWED,

AND THERE ARE NO OTHER EXPRESS

WARRANTIES EXCEPT THOSE EX-

PRESSLY STIPULATED HEREIN.

SOME STATES DO NOT ALLOW LIMITA-

TIONS ON HOW LONG AN IMPLIED WAR-

RANTY LASTS OR THE EXCLUSION OR

LIMITATIONS OF INCIDENTAL OR CONSE-

QUENTIAL DAMAGES, SO THE ABOVE LIM-

ITATIONS OR EXCLUSION MAY NOT APPLY

TO YOU.

This is a limited warranty within the meaning of that term as defined in the Magnuson--Moss Act of 1975.

The policy of Poulan is to continuously improve its products. Therefore, Poulan reserves the right to change, modify, or discontinue models, designs, specifications, and accessories of all products at any time without notice or obligation to any purchaser.

U.S. EPA/CALIFORNIA/ENVIRONMENT CANADA

EMISSION CONTROL WARRANTY STATEMENT

YOUR WARRANTY RIGHTS AND OB-

LIGATIONS: The U.S.

Environmental

Protection Agency, California Air Resources

Board, Environment Canada and Poulan are pleased to explain the emissions control system warranty on your year 2007 and later small off-road engine. In California, all small off--road engines must be designed, built, and equipped to meet the State’s stringent anti--smog standards. Poulan must warrant the emission control system on your small off--road engine for the periods of time listed below provided there has been no abuse, neglect, or improper maintenance of your small off--road engine.

Your emission control system includes parts such as the carburetor, the ignition system and the fuel tank (California only). Where a warrantable condition exists, Poulan will repair your small off--road engine at no cost to you. Expenses covered under warranty include diagnosis, parts and labor. MANUFACTURER’S

WARRANTY COVERAGE: If any emissions related part on your engine (as listed under

13

Emissions Control Warranty Parts List) is defective or a defect in the materials or workmanship of the engine causes the failure of such an emission related part, the part will be repaired or replaced by Poulan. OWNER’S WARRANTY

RESPONSIBILITIES: As the small off--road engine owner, you are responsible for the performance of the required maintenance listed in your instruction manual. Poulan recommends that you retain all receipts covering maintenance on your small off--road engine, but Poulan cannot deny warranty solely for the lack of receipts or for your failure to ensure the performance of all scheduled maintenance. As the small off--road engine owner, you should be aware that Poulan may deny you warranty coverage if your small off--road engine or a part of it has failed due to abuse, neglect, improper maintenance, unapproved modifications, or the use of parts not made or approved by the original equipment manufacturer. You are responsible for presenting your small off--road engine to a Poulan authorized re-

pair center as soon as a problem exists. Warranty repairs should be completed in a reasonable amount of time, not to exceed 30 days. If you have any questions regarding your warranty rights and responsibilities, you should contact your nearest authorized service center or call Poulan at 1--800--554--6723. WAR-

RANTY COMMENCEMENT DATE: The warranty period begins on the date the small off--road engine is purchased. LENGTH OF

COVERAGE: This warranty shall be for a period of two years from the initial date of purchase. WHAT IS COVERED: REPAIR OR

REPLACEMENT OF PARTS. Repair or replacement of any warranted part will be performed at no charge to the owner at an approved Poulan servicing center. If you have any questions regarding your warranty rights and responsibilities, you should contact your nearest authorized service center or call Poulan at 1--800--554--6723. WARRANTY PE-

RIOD: Any warranted part which is not scheduled for replacement as required maintenance, or which is scheduled only for regular inspection to the effect of “repair or replace as necessary” shall be warranted for 2 years.

Any warranted part which is scheduled for replacement as required maintenance shall be warranted for the period of time up to the first scheduled replacement point for that part.

DIAGNOSIS: The owner shall not be charged for diagnostic labor which leads to the determination that a warranted part is defective if the diagnostic work is performed at an approved Poulan servicing center.

CONSEQUENTIAL DAMAGES: Poulan may be liable for damages to other engine components caused by the failure of a warranted part still under warranty. WHAT IS

NOT COVERED: All failures caused by abuse, neglect, or improper maintenance are not covered. ADD--ON OR MODIFIED

PARTS: The use of add--on or modified parts can be grounds for disallowing a warranty claim. Poulan is not liable to cover failures of warranted parts caused by the use of add--on or modified parts. HOW TO FILE A CLAIM: If you have any questions regarding your warranty rights and responsibilities, you should contact your nearest authorized service center or call

Poulan at 1--800--554--6723. WHERE TO GET

WARRANTY SERVICE: Warranty services or repairs shall be provided at all Poulan service centers. Call: 1--800--554--6723. MAINTE-

NANCE, REPLACEMENT AND REPAIR

OF EMISSION RELATED PARTS: Any

Poulan approved replacement part used in the performance of any warranty maintenance or repair on emission related parts will be provided without charge to the owner if the part is under warranty. EMISSION CON-

TROL WARRANTY PARTS LIST: Carburetor, Ignition System: Spark Plug (covered up to maintenance schedule), Ignition Module,

Muffler including Catalyst, Fuel Tank (California only). MAINTENANCE STATEMENT:

The owner is responsible for the performance of all required maintenance as defined in the instruction manual.

The information on the product label indicates which standard your engine is certified.

Example: (Year) EPA Phase 1 or Phase 2 and/or CALIFORNIA.

This engine is certified to be emissions compliant for the following use:

Moderate (50 hours)

Intermediate (125 hours)

Extended (300 hours)

14

No results