Views of the Device 1 Stylus 2
1. Introduction
1. Introduction
Views of the Device
7
1
9
8
10
11
24
2
30
Stylus�
Write, draw, or make selection on the touch screen.
2
Scan key (left)
Press the key to scan and decode bar code/2D code.
3
Record key
Press and hold this key to record a voice note.
4
Volume up
Press the Volume up button to turn up the PDA receiver volume.
5
Volume down
Press the Volume down button to turn down the PDA receiver volume.
6
Reset button*
Press the Reset button with stylus to soft-reset your device.
7
Scanner
Point the reading window of the scanner in the direction of bar code/ 2D code.
8
Wi-Fi/Bluetooth LED
Indicates Wi-Fi/ Bluetooth Status.
9
Telephone receiver
Listen to a phone call here.
10
GSM/Battery LED
Indicates GSM/Battery LED.
11
Power button
Power on or off the device.
12
Display
2.8-inch TFT LCD with touch screen.
13
Soft key (left)
Performs the command shown in the label above the button.
14
Soft key (right)
Performs the command shown in the label above the button.
15
Fn key
16
Notification LEDs
The device has 2 notification LEDs: the left is Wi-Fi/Bluetooth LED and the right is
GSM/Battery LED.
Bluetooth/Wi-Fi LED tells you about the device’s Bluetooth/Wi-Fi status:
Color
Bluetooth on
Wi-Fi on
Green
Off
Blink
Blue
Blink
Off
Green and blue blink alternately while both Bluetooth and Wi-Fi are on.
GSM/Battery LED lets you know that you have unanswered calls or tells you about
the device’s GSM/battery status:
Helps you to perform special functions by using the keypad. For more information on
Color
Missed Call/ Low
Power
GSM on
(battery full)
GSM on (battery
low)
Charging
Backspace
Press this key to erase the letter on the left side of the cursor.
Red
Blink
Off
Blink
Off
17
Talk key
Press this key to dial or answer a call.
18
End key
End a call or close Phone application.
Orange
Off
Off
Off
Constantly on
Green
Off
Blink
Off
Off
19
5-way navigation key
20
Numeric keypad
21
Connect pins
22
Microphone
Speak into the microphone when talking on the phone or recording a voice note.
23
Eyelet for wrist strap (1)
Fix a wrist strap here.
24
Scan key (right)
Press the key to scan and decode bar code/ 2D code.
25
Eyelet for wrist strap (2)
Fix a wrist strap here.
26
Mini-SD card slot
Insert a mini-SD card to expand device memory.
27
Mini USB connector
Mini USB connector for PC sync and battery charging.
22
28
Earphone Jack
Connect a 2.5 mm Earphone.
23
29
Speaker
Listen to audio media or listen to a phone call hands-free.
30
Screw hole
Fasten the provided strap set here with screws.
31
Cover latch
Slide both of the cover latches to remove the battery cover.
32
Battery cover
Remove to place battery and SIM card.
26
12
5
27
6
13
14
15
16
17
18
19
20
21
1
1. Introduction
how to use the Fn key, refer to "ch2.2 Input Methods" in the user's manual.
25
3
4
29
1. Introduction
28
31
32
Press the multi directional control up, down, left, or right to move through menus; carry
1
2
3
4
5
6
7
AC adapter
Stereo headset
USB cable
Getting started CD
User manual/Quick guide
Pouch
Neck strap
1. Introduction
8
9
10
11
12
13
14
Belt clip
Battery
Strap set
UK plug
EU plug
AU plug
Stylus
Installing the SIM Card
If you want to use phone features, you must install a GSM SIM card.
• Slide both of the cover latches down and lift the battery cover in the direction
of the arrow to remove the battery cover.
out the selection by pressing the center button.
Enter numbers or letters by the numeric keypad.
Connect the connect pins of the device and the cradle (if any) for recharging the
• Place the SIM card in the SIM card slot with the
gold contacts facing down. The SIM card’s cut-off
corner should match the cut-off corner in the SIM
card slot.
• Press the battery down forcefully into the battery
slot.
2
1
• Angle the battery cover as shown in the diagram
and close the battery cover.
• Slide both of the cover latches up to lock the battery
cover.
Accessories
battery.
*Be sure to save all data in your device and then press the Power button to
switch your device off before resetting your device.
1
8
2
9
3
10
4
11
l
Manua
5
12
QSG
6
13
7
14
Please do not remove the battery cover when your device is in use;
otherwise, the device power will be shut off automatically and unsaved
data may be lost.
• Pull the plastic ribbon to remove the
battery.
The device contains a rechargeable Li-ion polymer battery completely
discharged and should be charged for at least 8 hours before first use.
Use only manufacturer-specified original batteries. Damages caused
by using batteries not specified by manufacturer are not covered under
warranty.
6061B0242401
2. Basic Operations
2. Basic Operations
3. Phone Features
3. Phone Features
Powering On/Off the Device
Press the POWER button to turn on the device. The POWER button is located on the
top of the front side of the device. When you power on
the device for the first time, you are asked to calibrate
the device. Please refer to the “Calibrating your device”
section in this chapter for calibration steps. Press the
POWER button again to switch the device to sleep mode.
You can still receive phone calls and messages when
the device is operating on sleep mode. To power off the
device completely, press and hold the POWER button for
3 seconds and the system will prompt you to power off the
device.
Icon Indicators
Status indicators appear at the top of the screen and on the Today screen. The
following table lists common status indicators and their meanings.
The Phone Screen
From the Phone screen, you can open, call, or find a contact, and even save a new
number in Contacts. To access the Phone screen, do any of the following:
• Press the Talk key (
).
• Tap
> Phone.
Making a Call from Call History
Call History displays calls you have made, received, and missed.
1. On the Phone screen, tap the Call History button on the Phone keypad.
Today Screen
The Today Screen is usually the first screen that appears when you turn on the device
for the first time each day. It displays a summary of information for the day, shows
you the system status and contains a list of shortcuts to programs. The Today screen
looks like this:
1
2
4
6
5
1
2
3
7
4
3
8
Tap here to rotate
the screen
5
6
7
8
Tap here to trigger the
Wireless Manager
Date and time
Wireless status (GSM, Wi-Fi, and Bluetooth)
Owner information
Unread messages including text messages, MMS
messages, and e-mails
Active tasks
Upcoming appointments
Live Search
Device lock status
New e-mail or text message (SMS)
Connection is not active
New voice mail
Synchronization in progress
New instant message
Ringer on
Voice call
Ringer off
Voice call in progress
Roaming
Data call in progress
No Voice mail
Calls are forwarded
Voice mail Lines 1
Call on hold
Call Forwarding Lines 1
Missed call
Alarm
Battery level 1
GPRS available
Battery level 2
GRPS in use
Low battery
No SIM card installed
Extremely low battery
EDGE available
Backup battery very low
EDGE in use
Battery charging
Wi-Fi connection in progress
Signal strength
Ringer in vibration mode
Bluetooth bonding in progress
Function key on
No signal
Synchronization error
Flight mode
Barcode reader off
No service
Barcode reader on
PC Connection is active
Making a Call by Entering a Phone Number
To enter phone numbers by tapping the screen directly, you have to open the Phone
Keypad.
1. On the Phone screen, if the Phone Keypad doesn’t show automatically, tap
Keypad. A Phone Keypad will show, you can then enter the phone number.
SIM Contact
Outlook Contact
2. Do one of the following after entering the phone number:
• If you see the number or contact name to call, select it, then tap
or
press the TALK(
) key.
• If you do not see the number or contact name, finish entering the number,
then tap
or press the TALK (
) key.
Tap
on the screen once to erase one single number; tap and hold it
to erase a whole string of numbers.
Call History
1.Calls you received
2.Calls you made
3.Calls you missed
2. Select the name or phone number to call.
3. Tap Call or press TALK (
).
Tap a phone number or a contact in the Call History list displays history
on all the calls related to the contact or the phone number.
When someone who isn’t in your list of contacts calls you, you can create
a contact during the call from or from Call History by tapping Menu >
Save to Contacts.
Making a Call from Contacts
1. On the Phone screen, tap on the desired contact in the list. You can quickly
search through Contacts by entering the first letter of the contact or the first
number of his/her phone number.
2. Do one of the following:
• Tap on the number you want to dial; otherwise, you can tap Call on the
screen or press TALK (
).
• Tap and hold the contact and select Call Work, Call Home, or Call
Mobile from the pop-up submenu.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising