PYLE Audio PSL122X Power Supply User Manual
OPERATION:
. INSERT AC POWER PLUG INTO A 1i10V VOLT AC OUTLET.
. CONNECT THE POWER CORD OF YOUR EQUIPMENT (13.5V-14.1VDC) TO
THE OUTPUT BINDING POST TERMINALS ON THE FRONT OF THE UNIT. BE
SURE THAT POLARITY IS CORRECT. THE RED POSITIVE( +) TERMINAL AND
BLACK NEGATIVE(—) TERMINAL ARE MARKED, REVERSAL OF POLARITY
MAY DAMAGE YOUR EQUIPMENT.
. TURN SWITCH TO “ON”, RED LIGHT IN SWITCH & GREEN LED WILL BE
ILLUMINATED.
. THE INPUT POWER IS PROTECTED BY THE FUSE WHICH IS LOCATED AT
THE REAR OF THE UNIT AND CAN BE REPLACED BY UNSCREWING THE
FUSE HOLDER IF THE FUSE IS BURNT OUT.DO NOT USE A FUSE LARGER
THAN 4.0 AMP. USE OF HEAVIER FUSE MAY RESULT IN DAMAGING TO
THIS UNIT.
. THIS UNIT HAS ELECTRONIC OVER LOAD PROTECTION WITH INSTANT
AUTOMATIC RESET FUNCTION. IF OUTPUT IS OVERLOADED. THE OUTPUT
POWER WILL AUTOMATICALLY SHUT OFF. RELEASE POWER CORD OF
YOUR EQUIPMENT FROM THE OUTPUT TERMINALS AND CHECK THE
ACTUAL POWER RATING OF YOUR EQUIPMENT. THIS UNIT WILL
AUTOMATICALLY RESET INSTANTLY.
CAUTIONS:
|.
2.
3.
4.
DO NOT USE WITH EQUIPMENT REQUIRING MORE THAN RATING AMPS.
DO NOT USE OUTDOORS. DO NOT EXPOSE UNIT TO RAIN, MOISTURE,
WATER OR ANY OTHER LIQUIDS.
DO NOT REMOVE COVER IN ANY CASE. RETURN TO DEALER FOR REPAIR
IF DAMAGED.
THIS UNIT HAS A SPECIAL BUILT-IN FEATURE THAT WILL SHUT THE UNIT
DOWN IF MARKED AMPERAGE IS EXCEEDED. THIS WILL AVOID BURN-OUT
OF YOUR EQUIPMENT AND OF UNIT. IF UNIT DOES CONSISTENTLY
SHUTDOWN. THIS MEANS YOU ARE DRAWING TOO MUCH AMPERAGE.
RETURN UNIT TO PLACE OF PURCHASE AND UPGRADE TO NEXT
AVAILABLE UNIT OFFERING HIGHER AMPERAGE. PLEASE DO NOT BYPASS
OR ALTER THIS CIRCUIT AS IT IS THERE TO PROTECT YOU. ANY
ALTERATION OF MISUSE WILL VOID YOUR WARRANTY.
“DANGER”
HIGH VOLTAGE
REFER TO QUALIFIED TECHNICIAN FOR SERVICE.
PYLE
REGULATED DC
POWER SUPPLY
MODEL: PSL122X
INSTRUCTION MANUAL
REGELATED ебу
EN supe
O inicias 2
= mr ee i
FOR i I T
5
Ps au
|
НРА ли
i
—_ y
a
www.pyleaudio.com
GENERAL SPECIFICATIONS
MODEL NO.: PSL122X
ELECTRICAL:
(A-1) INPUT RATING.
INPUT VOLTAGE: | 05-125VAC (1 | 5V NORMAL)
INPUT LINE FREQUENCY: 60Hz.
INPUT POWER: 250W MAX.
(A-2) OUTPUT RATING.
OUTPUT VOLTAGE: | 3.8VDC+ 0.3V
OUTPUT CURRENT: ¡O AMP CONSTANT/ 12 AMP SURGE.
OUTPUT RIPPLE: | SOmV RMS
(A-3) REGULATION.
LOAD REGULATION: 2.5% (280mV)
( NOTE :INPUT AT | 15VAC AND OUTPUT AT 10 AMP)
(A-4) PROTECTION.
INPUT LINE: GLASS TUBE FUSE 4.0 AMP 250V.
OVER-LOAD PROTECTION: +10n~ 15% (AUTO RESET).
OVER TEMPERATURE PROTECTION.
(A-5) WARNING /DEVICES.
THIS UNIT IS WELL BUILT WITH A WARNING/ SHUT DOWN FUNCTION.
THE WARNING/SHUT DOWN FUNCTION WILL WORK UNDER THE
FOLLOWING UNUSUAL STATUS:
1) THIS UNIT IS USED OVER 15 MINUTES AT 100% OF RATED LOAD.
2) THIS UNIT IS USED OVER 25 MINUTES AT 80% OF RATED LOAD.
3) THE OUTPUT OF THIS UNIT IS SHORT-CIRCUITED/ OVER LOAD/ OVER
TEMPERATURE
NOTES:
|) IF THE WARNING/ SHUT DOWN FUNCTION IS CAUSED BY THE ABOVE
ITEMS # | AND 2 THEN THIS UNIT WiLL RETURN TO NORMAL
WHEN THE WARNING / SHUT DOWN FUNCTION CONTINUES TO WORK
ABOUT | 5-30 MINUTES.
2) THIS UNIT IS INTENDED TO CONTINUOUSLY WORK AT 70% OF RATED LOAD
DESCRIPTION OF THE WARNING / SHUT DOWN FUNCTION:
STEP |. THE OUTPUT SHUT SHUT DOWN.
STEP 2.GREEN LED OF NORMAL OFF.
STEP 3. RED LED OF PROTECTION ON.
(A-6) EFFICIENCY: 60% MIN. (INPUT AT | 1 5VAC AND OUTPUT AT 10 AMP)
(A-7) DESIGN: LINEAR TYPE.
(A-8) OPERATING TEMPERATURE: 0 TO +40 DEG C.
(A-9) STORAGE TEMPERATURE: - 25 TO +70 DEG C.
MECHANICAL:
(B-1) DIMENSIONS: 207 mm x 194mm x 115 mm. (L xW xH)
(B-2) WEIGHT: 4-3KGS
(8-3) ENCLOSURE: SILVER
(8-4) INPUT CABLE: SPT-2 6FT |8AWG x 2C W/ 1-15P-P PLUG.
(B-5) OUTPUT TERMINAL: BINDING POST, [0A/ 125V.
(B-6) POWER SWITCH: ILLUMINATED, |5A/ 1 25VAC.
— 2 _
OUTPUT 13.87
O D14 1N5393
C8 100uF/25V
+— — |+
LED GRN
,
РО
¢ +
Ri4 2x2 — R10 4K7 R11 4K7 RIZ 10K
YR1 4K7
ee pe etd
{I
= C4 104 R4 10 ohm
Ss of IF I ||
alla
RE 270 R5470 Ré SES
| .
q rl #8 330 Diz 14148
C7 103
LED | ge
_ ) 8
tí R16 IK Ao (9) —
la +++
& C10 100uF/257 R47 | @ <)
4 р
es ох" (0) Es И
8 N =! 013 1N5393
+— — Л ‘
8 4700 ul /25V sf | y
= D10 1N4002
AZ Lg £7
— | 4700 uF/25V 1
a ® = ‘
+ —Kl = = й
Sch ZA : A ©
8 tn а
33 Е В 3 ©
— KK 3] ? = E p= =
=
[BASIC CIRCUIT DIAGRAM
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement