NordicTrack NTL14941, E 2500, E 2500 NTL14941 User manual

NordicTrack NTL14941, E 2500, E 2500 NTL14941 User manual
Model No. NTL12840
Serial No.
Find the serial number in the location
shown below. Write the serial number
in the space above for reference.
USER'S MANUAL
Serial Number Decal
QUESTIONS?
If you have questions, or if there
are missing parts, we will guarantee complete satisfaction
through direct assistance from
our factory.
TO AVOID DELAYS, PLEASE
CALL DIRECT TO OUR TOLLFREE CUSTOMER HOT LINE.
The trained technicians on our
Customer Hot Line will provide
immediate assistance, free of
charge to you.
CUSTOMER HOT LINE:
1-888-825-2588
Mon.–Fri., 6 a.m.–6 p.m. MST
Patent Pending
CAUTION
Read all precautions and instructions in this manual before using
this equipment. Save this manual
for future reference.
Visit our website at
www.nordictrack.com
new products, prizes,
fitness tips, and much more!
TABLE OF CONTENTS
IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
OPERATION AND ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
HOW TO FOLD AND MOVE THE TREADMILL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
CONDITIONING GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
PART LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
Note: An EXPLODED DRAWING is attached in the center of this manual.
NordicTrack is a registered trademark of ICON Health & Fitness, Inc.
2
IMPORTANT PRECAUTIONS
WARNING:
To reduce the risk of burns, fire, electric shock, or injury to persons, read the
following important precautions and information before operating the treadmill.
1. It is the responsibility of the owner to ensure
that all users of this treadmill are adequately
informed of all warnings and precautions.
12. Failure to use a properly functioning surge
suppressor could result in damage to the control system of the treadmill. If the control system is damaged, the walking belt may change
speed or stop unexpectedly, which may result
in a fall and serious injury.
2. Use the treadmill only as described.
3. Place the treadmill on a level surface, with at
least eight feet of clearance behind it and two
feet on each side. Do not place the treadmill
on any surface that blocks air openings. To
protect the floor or carpet from damage, place
a mat under the treadmill.
13. Keep the power cord and the surge suppressor away from heated surfaces.
4. Keep the treadmill indoors, away from moisture and dust. Do not put the treadmill in a
garage or covered patio, or near water.
14. Never move the walking belt while the power
is turned off. Do not operate the treadmill if
the power cord or plug is damaged, or if the
treadmill is not working properly. (See
BEFORE YOU BEGIN on page 5 if the treadmill is not working properly.)
5. Do not operate the treadmill where aerosol
products are used or where oxygen is being
administered.
15. Never start the treadmill while you are standing on the walking belt. Always hold the
handrails while using the treadmill.
6. Keep children under the age of 12 and pets
away from the treadmill at all times.
16. The treadmill is capable of high speeds.
Adjust the speed in small increments to avoid
sudden jumps in speed.
7. The treadmill should not be used by persons
weighing more than 275 pounds.
17. The pulse sensor is not a medical device.
Various factors, including the user's movement, may affect the accuracy of heart rate
readings. The pulse sensor is intended only
as an exercise aid in determining heart rate
trends in general.
8. Never allow more than one person on the
treadmill at a time.
9. Wear appropriate exercise clothes when
using the treadmill. Do not wear loose clothes
that could become caught in the treadmill.
Athletic support clothes are recommended for
both men and women. Always wear athletic
shoes. Never use the treadmill with bare feet,
wearing only stockings, or in sandals.
18. Never leave the treadmill unattended while it
is running. Always remove the key, unplug the
power cord, and switch the reset/off circuit
breaker to the off position when the treadmill
is not in use. (See the drawing on page 5 for
the location of the reset/off circuit breaker.)
10. When connecting the power cord (see page 9),
plug the power cord into a surge suppressor
(not included) and plug the surge suppressor
into a grounded circuit capable of carrying 15
or more amps. No other appliance should be on
the same circuit. Do not use an extension cord.
19. Do not attempt to raise, lower, or move the
treadmill until it is properly assembled. (See
ASSEMBLY on page 6, and HOW TO FOLD
AND MOVE THE TREADMILL on page 25.) You
must be able to safely lift 45 pounds (20 kg) to
raise, lower, or move the treadmill.
11. Use only a single-outlet surge suppressor that
meets all of the specifications described on
page 9. To purchase a surge suppressor, see
your local NordicTrack dealer or call 1-800806-3651 and order part number 146148.
20. Do not change the incline of the treadmill by
placing objects under the treadmill.
21. When folding or moving the treadmill, make
sure that the storage latch is fully closed.
3
22. When using iFIT.com CDs and videos, an
electronic “chirping” sound will alert you
when the speed and/or incline of the treadmill
is about to change. Always listen for the
“chirp” and be prepared for speed and/or incline changes. In some instances, the speed
and/or incline may change before the personal trainer describes the change.
26. Never insert or drop any object into any
opening.
27.
DANGER: Always unplug the power
cord immediately after use, before cleaning
the treadmill, and before performing the maintenance and adjustment procedures described in this manual. Never remove the
motor hood unless instructed to do so by an
authorized service representative. Servicing
other than the procedures in this manual
should be performed by an authorized service
representative only.
23. When using iFIT.com CDs and videos, you
can manually override the speed and incline
settings by pressing the speed and incline
buttons. However, when the next “chirp” is
heard, the speed and/or incline will change to
the next settings of the CD or video program.
28. The treadmill is intended for in-home use
only. Do not use the treadmill in any commercial, rental, or institutional setting.
24. Always remove iFIT.com CDs and videos from
your CD player or VCR when you are not
using them.
29. Keep the aromatherapy bottle out of the reach
of children. Essential oil may irritate skin and
is not intended for internal or topical use.
25. Inspect and properly tighten all parts of the
treadmill regularly.
WARNING:
Before beginning this or any exercise program, consult your physician. This
is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. ICON assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.
SAVE THESE INSTRUCTIONS
The decals shown have been placed on your treadmill and on the aromatherapy bottle. If a decal is missing or illegible, please call our Customer Service Department,
toll-free, to order a free replacement decal (see ORDERING REPLACEMENT PARTS
on page 31). Apply the decal in the location shown. Note: The decals may not be
shown at actual size.
4
BEFORE YOU BEGIN
Thank you for selecting the revolutionary NordicTrack®
C2250 treadmill. The C2250 treadmill combines advanced technology with innovative design to help you
get the most from your exercise program in the convenience of your home. And when you’re not exercising,
the unique C2250 treadmill can be folded up, requiring
less than half the floor space of other treadmills.
Department toll-free at 1-888-825-2588, Monday
through Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays). To help us assist you, please note
the product model number and serial number before
calling. The model number of the treadmill is
NTL12840. The serial number can be found on a decal
attached to the treadmill (see the front cover of this
manual for the location).
For your benefit, read this manual carefully before
using the treadmill. If you have questions after reading this manual, please call our Customer Service
Before reading further, please familiarize yourself with
the parts that are labeled in the drawing below.
Book Holder
Upper Handrail
Aromatherapy
Bottle Holder
Water Bottle Holder*
Fan
Console
Handrail
Pulse Sensor
Key/Clip
Latch Knob
RIGHT SIDE
Walking Belt
Reset/Off
Circuit Breaker
Foot Rail
Power Cord
Cushion Adjustment Knob
Cushioned Walking Platform
Rear Roller
Adjustment Bolts
*No water bottle is included.
5
ASSEMBLY
Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials. Do not
dispose of the packing materials until assembly is completed.
Note: The underside of the treadmill walking belt is coated with high-performance lubricant. During shipping, a
small amount of lubricant may be transferred to the top of the walking belt or the shipping carton. This is a normal
condition and does not affect treadmill performance. If there is lubricant on top of the walking belt, simply wipe off
the lubricant with a soft cloth and a mild, non-abrasive cleaner.
Assembly requires the included allen wrench
and your own phillips screwdriver
and
wire cutters
. For help identifying the assembly hardware, see the hardware drawings below.
4 1/2” Bolt (78)–4
Handrail Spacer
(77)–4
4” Bolt (53)–2
3” Bolt (125)–2
1” Tek Screw (47)–4
1. With the help of a second person, carefully raise the
Uprights (69) to the position shown.
Handrail Washer
(124)–2
1
See the inset drawing. Insert one of the Extension Legs
(102) into the treadmill as shown. Make sure that the
Extension Leg is turned so the Base Pad (99) is beneath it. Note: It may be helpful to tip the Uprights (69)
forward as you insert the Extension Leg.
69
69
Insert the other Extension Leg (not shown) in the same
way.
102
99
2. Press the Latch Knob Sleeve (70) into the left Upright (69).
Remove the Latch Knob (68) from the Latch Pin (74).
Make sure that the Latch Pin Collar (72) and the Spring
(71) are on the Latch Pin. Insert the Latch Pin into the
Latch Knob Sleeve (70) and the left Upright (69). Press
the Latch Knob Spacer (35) onto the other side of the left
Upright, and then tighten the Latch Knob back onto the
Latch Pin.
6
2
68 35
69
70
71
72
74
3. Cut the rubber band securing the Upright Wire Harness
(98). Have a second person hold the console assembly
near the Uprights (69). Connect the Upright Wire Harness
to the wires extending from the Console Base (81). The
connectors should slide together easily and snap into
place. If they do not, turn one connector and try again.
Insert the connectors and the Upright Wire Harness down
into the right Upright, and then set the console assembly
on the Uprights. Be careful not to pinch the wires.
3
98
81
98
69
Console
Assembly
4. Insert a Handrail (118) into the right side of the console
assembly as shown. (Note: It may be helpful to twist the
Handrail as you insert it.) Next, insert two 4 1/2” Bolts (78)
with Handrail Spacers (77) into the right Upright (69) and
the Handrail. Be careful not to pinch the wires. Make
sure that the Handrail Spacers are flush against the right
Upright, with the thicker sides of the Handrail Spacers
toward the center of the treadmill, as shown in the inset
drawing.
Next, lift the console assembly and the Handrail (118)
slightly and align the 4 1/2” Bolts (78) with the holes in the
Handrail. Thread the Bolts into the Handrail until the
heads of the Bolts are against the right Upright (69). Do
not tighten the Bolts yet.
4
69
77
Thick
Side
118
77
78
Console
Assembly
Attach the other Handrail (not shown) in the same way.
Note: There are no wires on the left side.
5. With the help of a second person, carefully tip the
Uprights (69) down to the position shown. Make sure that
the Extension Legs (102) remain in the Uprights.
Attach each Extension Leg (102) with two 1” Screws (47)
and a Base Pad (99) as shown. Note: Attach the lower
Screw (without the Base Pad) first.
5
99
69
99
Next, align the lower ends of the Handrails (118) with the
holes in the base of the Uprights (69). Attach each
Handrail with a 4” Bolt (53) as shown. Note: The Bolts
must be at an angle that matches the angle of the
Handrails, as shown in the inset drawing.
Note: A replacement Base Pad (99) may be included. Use
the Base Pad to replace any Base Pad that becomes worn.
53
99
47
99
102
53
118
99
47
102
53
99
118
7
6. Attach the Upper Handrail (122) to the Uprights (69)
with two 3” Bolts (125) and two Handrail Washers
(124). Firmly tighten the Bolts.
6
122
With the help of a second person, carefully tip the
Uprights (69) back to the vertical position. See step 4.
Tighten the four 4 1/2” Bolts (78).
69
7. Make sure that all parts are properly tightened before you use the treadmill. Keep the included allen
wrench in a secure place. The allen wrench is used to
adjust the walking belt (see page 28). To protect the
floor or carpet from damage, place a mat under the
treadmill.
124
125
If you purchase the optional chest pulse sensor (see page 24), follow the steps below to install the receiver
and the short jumper wire included with the chest pulse sensor.
Make sure that the power cord is unplugged.
1
82
See step 6 above. Remove the two 3” Bolts (125), the two
Handrail Washers (124), and the Upper Handrail (122).
1. Remove the indicated screws from the Console Back (88).
(Important: The screws may be different lengths; remember which hole each screw was removed from.)
Next, remove the Console Back.
88
Screws
2. Peel the paper off the pad on the bottom of the receiver
(A). Turn the receiver so the small cylinder is on the
side shown, and press the receiver onto the Console
Base (81) in the indicated location.
2
A
Cylinder
81
3. Connect the included short jumper wire (B) to the wire on
the receiver (A). Connect the other end of the short
jumper wire to the PLS2 jack on the underside of the
Console (82). (Note: If there is already a wire in the PLS2
jack, unplug it.) Discard the other wires included with the
receiver. Use the included wire tie to secure the wires, if
needed.
Make sure that no wires are pinched. See step 1.
Reattach the Console (82), making sure that the
screws are inserted into the same holes from which
they were removed. See step 6. Reattach the Upper
Handrail (122).
8
3
PLS2
Jack
82
B
A
OPERATION AND ADJUSTMENT
THE PERFORMANT LUBETM WALKING BELT
an equipment-grounding conductor and a grounding
plug. Plug the power cord into a surge suppressor,
and plug the surge suppressor into an appropriate
outlet that is properly installed and grounded in
accordance with all local codes and ordinances.
Important: The treadmill is not compatible with
GFCI-equipped outlets.
Your treadmill features a walking belt coated with
PERFORMANT LUBETM, a high-performance lubricant.
IMPORTANT: Never apply silicone spray or other
substances to the walking belt or the walking platform. Such substances will deteriorate the walking
belt and cause excessive wear.
This product is for use on a nominal 120-volt circuit,
and has a grounding plug that looks like the plug illustrated in drawing 1 below. A temporary adapter that
looks like the adapter illustrated in drawing 2 may be
used to connect the surge suppressor to a 2-pole
receptacle as shown in drawing 2 if a properly
grounded outlet is not available.
HOW TO PLUG IN THE POWER CORD
DANGER:
Improper connection
of the equipment-grounding conductor can
result in an increased risk of electric shock.
Check with a qualified electrician or serviceman if you are in doubt as to whether the
product is properly grounded. Do not modify
the plug provided with the product—if it will
not fit the outlet, have a proper outlet
installed by a qualified electrician.
1
Grounded Outlet Box
Surge Suppressor
Grounding Pin
Your treadmill, like any other type of sophisticated
electronic equipment, can be seriously damaged by
sudden voltage changes in your home’s power.
Voltage surges, spikes, and noise interference can
result from weather conditions or from other appliances
being turned on or off. To decrease the possibility of
your treadmill being damaged, always use a surge
suppressor with your treadmill (see drawing 1 at
the right). To purchase a surge suppressor, see
your local NordicTrack dealer or call 1-800-8063651 and order part number 146148.
Grounding Pin
Grounded Outlet
Grounding Plug
2
Grounded Outlet Box
Adapter
Use only a single-outlet surge suppressor that is
UL 1449 listed as a transient voltage surge suppressor (TVSS). The surge suppressor must have a
UL suppressed voltage rating of 400 volts or less
and a minimum surge dissipation of 450 joules.
The surge suppressor must be electrically rated
for 120 volts AC and 15 amps. There must be a
monitoring light on the surge suppressor to indicate whether it is functioning properly. Failure to
use a properly functioning surge suppressor could
result in damage to the control system of the
treadmill. If the control system is damaged, the
walking belt may change speed or stop unexpectedly, which may result in a fall and serious injury.
Surge Suppressor
Lug
Metal Screw
The temporary adapter should be used only until a
properly grounded outlet (drawing 1) can be installed
by a qualified electrician.
The green-colored rigid ear, lug, or the like extending
from the adapter must be connected to a permanent
ground such as a properly grounded outlet box cover.
Whenever the adapter is used it must be held in place
by a metal screw. Some 2-pole receptacle outlet box
covers are not grounded. Contact a qualified electrician to determine if the outlet box cover is
grounded before using an adapter.
This product must be grounded. If it should malfunction or break down, grounding provides a path of least
resistance for electric current to reduce the risk of electric shock. This product is equipped with a cord having
9
Program Display
Pulse
Sensor
Note: If there is a sheet of clear
plastic on the console, remove it.
Pulse
Sensor
Clip
Key
FEATURES OF THE CONSOLE
The advanced console offers an impressive array of
features designed to help you get the most from your
exercise. When the manual mode is selected, the
speed and incline of the treadmill can be changed with
the touch of a button. As you exercise, the console will
provide continuous exercise feedback. You can even
measure your heart rate using the built-in handgrip
pulse sensor. Note: For information about an optional
chest pulse sensor, see page 24.
personal trainer in your home. Using the included audio
cable, you can connect the treadmill to your home
stereo, portable stereo, computer, or VCR and play
special iFIT.com CD and video programs (iFIT.com
CDs and videocassettes are available separately).
iFIT.com CD and video programs automatically control
the speed and incline of the treadmill as a personal
trainer coaches you through every step of your workout.
High-energy music provides added motivation. To purchase iFIT.com CDs or videocassettes, call tollfree 1-800-735-0768.
The console also offers six preset workout programs.
Each program automatically controls the speed and incline of the treadmill to give you an effective workout.
You can even create your own custom workout programs and store them in memory for future use.
With the treadmill connected to your computer, you
can also go to our Web site at www.iFIT.com and access programs directly from the internet. Additional options are soon to be available. See www.iFIT.com for
more information.
In addition, the console offers two heart rate programs
that automatically adjust the speed and incline of the
treadmill to keep your heart rate near a target level
while you exercise. Note: The heart rate programs require the use of the optional chest pulse sensor.
To use the manual mode of the console, follow the
steps beginning on page 11. To use a preset program,
see page 13. To create and use a custom program,
see pages 15 and 16. To use a heart rate program,
see page 17. To use an iFIT.com CD or video program, see page 21. To use an iFIT.com program directly from our Web site, see page 23.
The console also features new iFIT.com interactive
technology. Having iFIT.com technology is like having a
10
HOW TO USE THE MANUAL MODE
CAUTION: Before operating the
console, read the following precautions.
1
• Do not stand on the walking belt when turning on the power.
See HOW TO TURN ON THE POWER at the left.
• Always wear the clip (see the drawing on
page 10) while operating the treadmill.
2
• The pulse sensor is not a medical device.
Various factors, including the user’s movement, may affect the accuracy of heart rate
readings. The pulse sensor is intended only
as an exercise aid in determining heart rate
trends in general.
• To reduce the possibility of electric shock,
keep the console dry. Avoid spilling liquids
on the console and place only a sealed water
bottle in the water bottle holder.
3
If the Start button or the
Speed + button is
pressed, the walking belt
will begin to move at 1
mph. As you exercise,
change the speed of the
walking belt as desired by pressing the Speed +
and – buttons. Each time a button is pressed, the
speed setting will change by 0.1 mph; if a button
is held down, the speed setting will change in increments of 0.5 mph.
Plug in the power cord.
See page 9.
Move the reset/off circuit breaker to the reset
position.
Locate the reset/off circuit breaker on the
treadmill near the power
cord. Make sure that the
circuit breaker is in the
reset position.
3
Start the walking belt.
To start the walking belt, press the Start button,
the Speed + button, or one of the ten 1-Step
Speed buttons.
HOW TO TURN ON THE POWER
2
Select the manual mode.
When the key is
inserted, the manual mode will be
selected. If a program has been selected, press the
Select Program
button repeatedly until a track appears in the program display but the indicator above the iFIT.com
button is not lit.
• Adjust the speed in small increments to
avoid sudden jumps in speed.
1
Insert the key fully into the console.
Reset
Position
If one of the 1-Step Speed buttons is pressed, the
walking belt will gradually increase in speed until it
reaches the selected speed setting. Note: The
console can display speed and distance in either miles or kilometers. For simplicity, all instructions in this section refer to miles.
Attach the clip to the waistband of your clothes.
Stand on the foot rails of the treadmill. Find the clip
attached to the key (see the drawing on page 10),
and slide the clip onto the waistband of your
clothes. Next, insert the key into the console. Test
the clip by carefully taking a few steps backward until the key is pulled from the console. If
the key is not pulled from the console, adjust
the position of the clip as needed. Then, remove the key from the console.
To stop the walking belt, press the Stop button.
The time will begin to flash in the Time/Pace display. To restart the walking belt, press the Start
button, the Speed + button, or one of the 1-Step
Speed buttons.
Note: During the first few minutes that the treadmill
is used, observe the alignment of the walking belt,
and align it if necessary (see page 28).
11
4
Time/Pace display—
When the manual mode
or the iFIT.com mode is
selected, this display will
show the elapsed time
and your current pace
(pace is measured in minutes per mile). When a
program is selected, the display will show the time
remaining in the program, the time remaining in
the current segment of the program, and your current pace. The display will change from one number to the next every few seconds, as shown by
the indicators below the display.
Change the incline of the treadmill as desired.
To change the incline of
the treadmill, press the
Incline buttons. Each
time a button is
pressed, the incline will
change by 0.5%. To
change the incline setting quickly, press the 1-step
Incline buttons. Note: It may take a moment for the
treadmill to reach the selected incline setting.
5
Follow your progress with the displays.
Calories/Fat Calories
display—This display
shows the approximate
numbers of calories and
fat calories you have
burned (see FAT BURNING on page 29). The display will change from
one number to the other every few seconds, as
shown by the indicator below the display.
The program
display—When
the manual mode
or the iFIT.com
mode is selected,
the program display will show a
track representing 1/4 mile. As you exercise, the
indicators around the track will light in succession
until the entire track is lit. The track will then
darken and the indicators will again begin to light
in succession.
Note: The display will show calories and fat calories more accurately if you enter your weight. To
enter your weight, the manual mode must be selected. Press the Age/Weight Set buttons repeatedly to enter your weight. The weight setting will
be shown in the Speed display. A few seconds
after the buttons are last pressed, the weight setting will disappear from the display. Your weight
will then be saved in memory.
The Training Zone
display—As you exercise, the Training Zone
display will show the
approximate intensity
level of your exercise.
For example, if three or four indicators are lit, your
intensity level is ideal for fat burning.
Speed display—This
display shows the speed
of the walking belt.
Incline/Heart Rate
display—This display
shows the incline level
of the treadmill. When
the handgrip pulse sensor or the optional
chest pulse sensor is used, the display will also
show your heart rate. Note: Each time the incline
level changes, the display will show the incline
level.
Note: When the Km/H
indicator below the
Speed display is lit, the
console will display
speed and distance in
kilometers; when the indicator is not lit, the console will display speed
and distance in miles. To change the unit of measurement, first hold down the Stop button while inserting the key into the console. An “E” for English
miles or an “M” for metric kilometers will appear in
the Speed display. Press the Speed + button to
change the unit of measurement. When the desired unit of measurement is selected, remove the
key and then reinsert it. Note: For simplicity, all
instructions in this manual refer to miles.
Distance/Laps
display—This display
shows the distance that
you have walked or run
and the number of 1/4mile laps you have
completed. The display will change from one number to the other every few seconds, as shown by
the Laps indicator below the display.
12
To reset the displays, press the Stop button, remove the key, and then reinsert the key.
6
HOW TO USE PRESET PROGRAMS
Measure your heart rate if desired.
1
See HOW TO TURN ON THE POWER on page
11.
To measure your
Metal Contacts
heart rate, stand
on the foot rails
and place your
hands on the
metal contacts on
the handgrip pulse
sensor. Your
palms must be
resting on the
upper contacts,
and your fingers
must be touching
the lower contacts—avoid moving your hands. When your
pulse is detected, the Heart Rate indicator below
the Incline/Heart Rate display will light, two or
three dashes (– – –) will appear in the display, and
then your heart rate will be shown. For the most
accurate heart rate reading, continue to hold
the contacts for about 15 seconds.
7
2
Select one of the preset programs.
When the key is
inserted, the manual mode will be
selected. To select
a preset program,
press the Select
Program button repeatedly until the Power Burn, Endurance Run,
Pace Setter Plus, Aerobic Speed Interval, Runner’s
High, or Fitness Challenge indicator lights.
For about six seconds after a program is selected,
the Incline/Heart Rate display will flash the maximum incline setting for the program, and the
Speed display will flash the maximum speed setting for the program. The Time/Pace display will
show how long the program will last. The program
display will show the first ten speed settings for
the program.
Turn on the fans if desired.
To turn on the fans at low speed, press the Fans
button. To turn on the fans at high speed, press
the button a second time. To turn off the fans,
press the button a third time. Note: Any time that
the walking belt is stopped for a few minutes, the
fans will automatically turn off.
8
Insert the key fully into the console.
3
Press the Start button or the Speed + button to
start the program.
A moment after the button is pressed, the treadmill will automatically adjust to the first speed and
incline settings for the program. Hold the handrails
and begin walking.
When you are finished exercising, stop the
walking belt and remove the key.
Each program is divided into several time segments of different lengths. (The Time/Pace display
will show both the time remaining in the program
and the time remaining in the current segment.)
One speed setting and one incline setting are programmed for each segment. (The same speed
setting and/or incline setting may be programmed
for two or more consecutive segments.)
Step onto the foot rails, press the Stop button, and
adjust the incline of the treadmill to the lowest level.
The incline must be at the lowest level when
the treadmill is raised to the storage position or
the treadmill will be damaged. Next, remove the
key from the console and put it in a secure place.
Note: If the displays and indicators on the console remain lit after the key is removed, the
console is in the “demo” mode. See page 24
and turn off the demo mode.
The speed setting
Current Segment
for the first segment will be shown
in the flashing
Current Segment
column of the program display. (The
incline settings are
not shown in the program display.) The speed settings for the next several segments will be shown
in the columns to the right.
When you are finished using the treadmill, switch
the reset/off circuit breaker to the off position and
unplug the power cord.
13
When only three seconds remain in the first segment of the program, both the Current Segment
column and the column to the right will flash and a
series of tones will sound. If the speed and/or incline of the treadmill is about to change, the Speed
display and/or the Incline/Heart Rate display will
flash to alert you. When the first segment ends, all
speed settings will move one column to the left.
The speed setting for the second segment will then
be shown in the flashing Current Segment column
and the treadmill will automatically adjust to the
speed and incline settings for the second segment.
Note: If all of the indicators in the Current Segment
column are lit after the speed settings have moved
to the left, the speed settings will move downward
so that only the highest indicators appear in the
program display. If some of the indicators in the
Current Segment column are not lit when the
speed settings move to the left again, the speed
settings will move back up.
To stop the program temporarily, press the Stop
button. The Time/Pace display will begin to flash.
To restart the program, press the Start button or
the Speed + button. The walking belt will begin to
move at 1 mph. When the next segment of the program begins, the treadmill will automatically adjust
to the speed and incline settings for the next segment. To end the program, press the Stop button,
remove the key, and then reinsert the key.
4
Follow your progress with the displays.
See step 5 on page 12.
5
Measure your heart rate if desired.
See step 6 on page 13.
6
Turn on the fans if desired.
See step 7 on page 13.
The program will continue until the speed setting
for the last segment is shown in the Current
Segment column and the last segment ends. The
walking belt will then slow to a stop.
7
When you are finished exercising, remove the
key.
Step onto the foot rails and make sure that the incline of the treadmill is at the lowest level. The incline must be at the lowest level when the
treadmill is raised to the storage position. Next,
remove the key from the console and put it in a secure place. Note: If the displays and indicators
on the console remain lit after the key is removed, the console is in the “demo” mode.
See page 24 and turn off the demo mode.
If the speed or incline setting is too high or too low
at any time during the program, you can manually
override the setting by pressing the Speed or
Incline buttons. Every few times a Speed button is
pressed, an additional indicator will light or darken
in the Current Segment column. (If any of the
columns to the right of the Current Segment column have the same number of lit indicators as the
Current Segment column, an additional indicator
may light or darken in those columns as well.)
Note: If you manually override the speed or incline setting, when the next segment begins,
the treadmill will automatically adjust to the
speed and incline settings for the next segment.
When you are finished using the treadmill, switch
the reset/off circuit breaker to the off position and
unplug the power cord.
14
tional indicator will light or darken in the Current
Segment column.
HOW TO CREATE CUSTOM PROGRAMS
1
During the last three seconds of the first segment,
both the Current Segment column and the column
to the right will flash, a series of tones will sound,
and the Speed display and the Incline/Distance
display will flash. When the first segment ends, the
current speed setting and the current incline setting will be saved in memory, and all speed settings in the program display will move one column
to the left. The speed setting for the second segment will then be shown in the flashing Current
Segment column. Program a speed setting and an
incline setting for the second segment as described above. Note: After the third segment ends,
the speed settings in the program display will no
longer move to the left. Instead, each time a segment ends, the flashing Current Segment column
will move one column to the right. If the Current
Segment column reaches the right side of the program display, when the current segment ends, all
columns of indicators in the program display will
move three columns to the left.
Insert the key fully into the console.
See HOW TO TURN ON THE POWER on page
11.
2
Select one of the custom programs.
When the key is
inserted, the
manual mode will
be selected. To
select a custom
program, press
the Select
Program button repeatedly until the Learn 1 or
Learn 2 indicator lights.
Note: If the custom program has not yet been
defined, three columns of indicators will be lit
in the program display. If more than three
columns of indicators are lit, see HOW TO USE
CUSTOM PROGRAMS on page 16.
3
Continue programming speed and incline settings
for as many segments as desired; custom programs can have up to forty segments. When you
are finished with your workout, press the Stop button twice. The speed and incline settings that you
have programmed and the number of segments
that you have programmed will then be saved in
memory.
Press the Start button or the Speed + button
and program the desired speed and incline
settings.
A moment after the button is pressed, the walking
belt will begin to move. Hold the handrails and
begin walking.
See the program display. Each custom program is
divided into one-minute segments. One speed
setting and one incline setting can be programmed for each segment. The speed setting for
the first segment will be shown in the flashing
Current Segment
column of the
Current Segment
program display.
(The incline settings are not
shown in the program display.) To
program a speed
setting and an incline setting for the first segment, simply adjust
the speed and incline of the treadmill as desired
by pressing the Speed and Incline buttons. Every
few times a Speed button is pressed, an addi-
4
Follow your progress with the displays.
See step 5 on page 12.
5
Measure your heart rate if desired.
See step 6 on page 13.
6
Turn on the fans if desired.
See step 7 on page 13.
7
When you are finished exercising, remove the
key.
See step 7 on page 14.
15
When only three seconds remain in the first segment of the program, both the Current Segment
column and the column to the right will flash and a
tone will sound. If the speed and/or incline of the
treadmill is about to change, the Speed/Pace display and/or the Incline/Heart Rate display will
flash to alert you, and three tones will sound.
When the first segment ends, all speed settings
will move one column to the left. The speed setting for the second segment will then be shown in
the flashing Current Segment column and the
treadmill will automatically adjust to the speed and
incline settings for the second segment.
HOW TO USE CUSTOM PROGRAMS
1
Insert the key fully into the console.
See HOW TO TURN ON THE POWER on page
11.
2
Select one of the custom programs.
When the key is
inserted, the
manual mode will
be selected. To
select a custom
program, press
the Select
Program button repeatedly until the Learn 1 or
Learn 2 indicator lights.
The program will continue until the speed setting
for the last segment is shown in the Current
Segment column and no time remains. The walking belt will then slow to a stop.
If desired, you can redefine the program while
using it. To change the speed or incline setting
for the current segment, simply press the Speed
or Incline buttons. When the current segment ends,
the new setting will be saved in memory. To increase the length of the program, first wait until
the program ends. Then, press the Start button and
program speed and incline settings for as many additional segments as desired. Note: While you are
adding segments to the program, the speed settings in the program display will not move to the
left. Instead, each time a segment ends, the flashing Current Segment column will move one column to the right. If the Current Segment column
reaches the right side of the program display,
when the current segment ends, all columns of indicators in the program display will move three
columns to the left. When you have added as
many segments as desired, press the Stop button
twice. To decrease the length of the program,
press the Stop button twice at any time before the
program ends.
For about six seconds after a program is selected,
the Incline/Heart Rate display will flash the maximum incline setting for the program, and the
Speed display will flash the maximum speed setting for the program. The Time/Pace display will
show how long the program will last. The program
display will show the first ten speed settings for
the program. Note: If only three columns of indicators are lit in the program display, see
HOW TO CREATE A CUSTOM PROGRAM on
page 15.
3
Press the Start button or the Speed + button to
start the program.
A moment after the button is pressed, the walking
belt will begin to move. Hold the handrails and
begin walking.
Each program is divided into several one-minute
segments. One speed setting and one incline setting are programmed for each segment. The
speed setting for the first segment will be shown in
the flashing Current Segment column of the program display. (The incline settings are not shown
in the program
display.) The
Current Segment
speed settings for
the next several
segments will be
shown in the
columns to the
right.
To stop the program at any time, press the Stop
button. The time will begin to flash in the
Time/Pace display. To restart the program, press
the Start button or the Speed + button. The walking belt will begin to move at 1 mph. When the next
segment of the program begins, the treadmill will
automatically adjust to the speed and incline settings for the next segment.
16
4
Follow your progress with the displays.
HOW TO USE HEART RATE PROGRAMS
See step 5 on page 12.
5
CAUTION:
Measure your heart rate if desired.
If you have heart problems, or if you are over 60 years of age and
have been inactive, do not use the heart rate
programs. If you are taking medication regularly, consult your physician to find whether the
medication will affect your exercise heart rate.
See step 6 on page 13.
6
Turn on the fans if desired.
See step 7 on page 13.
7
When you are finished exercising, remove the
key.
See step 7 on page 14.
Follow the steps below to use a heart rate program.
Note: You must wear the optional chest pulse sensor (see page 24) to use a heart rate program.
1
Put on the optional chest pulse sensor.
See the instructions included with the optional
chest pulse sensor.
2
Insert the key fully into the console.
See HOW TO TURN ON THE POWER on page
11.
3
Select a heart rate program.
When the key is
inserted, the manual mode will be
selected. To select
a heart rate program, press the
Select Program
button repeatedly until the HR1 or HR2 indicator
lights.
During heart rate
programs, the
program display
will show a
graphic that represents your
heart rate. Each
time a heartbeat
is detected, an additional peak will appear.
17
4
the treadmill will automatically increase or decrease to bring your heart rate closer to the target
heart rate setting. If the speed reaches the maximum speed limit for the program (see step 5 at
the left) and your heart rate is still too far below
the current target heart rate setting, the incline of
the treadmill will also increase to bring your heart
rate closer to the target heart rate setting.
Enter your age.
When a heart rate program is selected, the
letters “AGE” and the
current age setting will
begin to flash in the
Speed display. You
must enter your age to use a heart rate program. If
you have already entered your age, press the Start
button (pressing the Start button at this time will
not start the program). If you have not entered
your age, press the Age/Weight Set buttons until
your age is shown. Then, press the Start button.
Your age will then be saved in memory.
5
The program will continue until no time remains in
the program. The walking belt will then slow to a
stop.
If the current speed or incline setting is too high or
too low, you can adjust the setting with the Speed
or Incline buttons. However, each time the console compares your heart rate to the current target
heart rate setting, the speed and/or incline of the
treadmill may automatically change to bring your
heart rate closer to the target heart rate setting.
Adjust the maximum speed limit for the
program.
After you have entered
your age, the letters
“SPd” (speed) and the
maximum speed limit
for the program will
flash in the Speed display. If desired, change the maximum speed limit
by pressing the Speed buttons.
6
If your pulse is not detected during the program,
the letters “PLS” will flash in the Incline/Heart Rate
display and the speed and incline of the treadmill
may automatically decrease until your pulse is detected. If this occurs, see the instructions included
with the chest pulse sensor.
To stop the program at any time, press the Stop
button. Heart rate programs should not be stopped
temporarily and then restarted. To use a heart rate
program again, reselect the program and start it at
the beginning.
Press the Start button or the Speed + button to
start the program.
A moment after the button is pressed, the treadmill will automatically adjust to the first speed and
incline settings for the program. Hold the handrails
and begin walking.
7
Follow your progress with the displays.
See step 5 on page 12.
Each heart rate program is divided into 20 oneminute segments. (The Time/Pace display will
show both the time remaining in the program and
the time remaining in the current segment of the
program.) One target heart rate setting is programmed for each segment. (The same target
heart rate setting may be programmed for two or
more consecutive segments.)
8
Turn on the fans if desired.
See step 7 on page 13.
9
During the program, the console will regularly
compare your heart rate to the current target heart
rate setting. If your heart rate is too far below or
above the target heart rate setting, the speed of
When you are finished exercising, remove the
key.
See step 7 on page 14.
18
HOW TO CONNECT THE TREADMILL TO YOUR
CD PLAYER, VCR, OR COMPUTER
To use iFIT.com CDs, the treadmill must be connected to your portable CD player, portable stereo,
home stereo, or computer with CD player. See pages
19 and 20 for connecting instructions. To use iFIT.com
videocassettes, the treadmill must be connected to
your VCR. See page 21 for connecting instructions. To
use iFIT.com programs directly from our Web site,
the treadmill must be connected to your home computer. See page 20 for connecting instructions.
HOW TO CONNECT YOUR PORTABLE STEREO
Note: If your stereo has an RCA-type AUDIO OUT
jack, see instruction A below. If your stereo has a
3.5mm LINE OUT jack, see instruction B. If your
stereo has only a PHONES jack, see instruction C.
A. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the included adapter. Plug
the adapter into an AUDIO OUT jack on your stereo.
A
HOW TO CONNECT YOUR PORTABLE CD PLAYER
AUDIO OUT
RIGHT
Note: If your CD player has separate LINE OUT and
PHONES jacks, see instruction A below. If your CD
player has only one jack, see instruction B.
A. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the LINE OUT jack on
your CD player. Plug your headphones into the
PHONES jack.
A
PHONES LINE OUT
LINE OUT
LEFT
Audio
Cable
Adapter
B. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the LINE OUT jack on
your stereo.
PHONES
B
Headphones
Audio
Cable
LINE OUT
Audio
Cable
B. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into a 3.5mm Y-adapter
(available at electronics stores). Plug the Y-adapter
into the PHONES jack on your CD player. Plug your
headphones into the other side of the Y-adapter.
B
C. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into a 3.5mm Y-adapter
(available at electronics stores). Plug the Y-adapter
into the PHONES jack on your stereo. Plug your
headphones into the other side of the Y-adapter.
PHONES
C
PHONES
Audio
Cable
3.5mm
Y-adapter
PHONES
Audio
Cable
Headphones
3.5mm
Y-adapter
Headphones
19
HOW TO CONNECT YOUR HOME STEREO
HOW TO CONNECT YOUR COMPUTER
Note: If your stereo has an unused LINE OUT jack,
see instruction A below. If the LINE OUT jack is
being used, see instruction B.
Note: If your computer has a 3.5mm LINE OUT jack,
see instruction A. If your computer has only a
PHONES jack, see instruction B.
A. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the included adapter.
Plug the adapter into the LINE OUT jack on your
stereo.
A. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the LINE OUT jack on
your computer.
A
A
CD
LINE OUT
VCR
Amp
LINE OUT
Audio
Cable
LINE OUT
Audio
Cable
Adapter
B. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into a 3.5mm Y-adapter
(available at electronics stores). Plug the Y-adapter
into the PHONES jack on your computer. Plug your
headphones or speakers into the other side of the
Y-adapter.
B. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the included adapter.
Plug the adapter into an RCA Y-adapter (available
at electronics stores). Next, remove the wire that is
currently plugged into the LINE OUT jack on your
stereo and plug the wire into the unused side of the
RCA Y-adapter. Plug the RCA Y-adapter into the
LINE OUT jack on your stereo.
B
B
PHONES
CD
Audio
Cable
VCR
Amp
3.5mm
Y-adapter
LINE OUT
Headphones/Speakers
Audio
Cable
RCA
Y-adapter
Adapter
Wire removed from
LINE OUT jack
20
HOW TO CONNECT YOUR VCR
Note: If your VCR has an unused AUDIO OUT jack,
see instruction A below. If the AUDIO OUT jack is
being used, see instruction B. If you have a TV
with a built-in VCR, see instruction B. If your VCR
is connected to your home stereo, see HOW TO
CONNECT YOUR HOME STEREO on page 20.
A. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the included adapter.
Plug the adapter into the AUDIO OUT jack on your
VCR.
HOW TO USE IFIT.COM CD AND VIDEO
PROGRAMS
To use iFIT.com CDs or videocassettes, the treadmill
must be connected to your portable CD player, portable
stereo, home stereo, computer with CD player, or
VCR. See HOW TO CONNECT THE TREADMILL TO
YOUR CD PLAYER, VCR, OR COMPUTER on pages
19 to 21. Note: To purchase iFIT.com CDs or videocassettes, call toll-free 1-800-735-0768.
Follow the steps below to use an iFIT.com CD or video
program.
A
1
ANT. IN
VIDEO AUDIO
IN
RF OUT
CH
3 4
OUT
Insert the key fully into the console.
See HOW TO TURN ON THE POWER on page
11.
AUDIO OUT
RIGHT
LEFT
Audio
Cable
2
Adapter
When the key is inserted, the manual
mode will be selected.
To use an iFIT.com CD
or video program, press
the iFIT.com button or
press the Select Program button repeatedly until
the indicator above the iFIT.com button lights.
B. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the included adapter.
Plug the adapter into an RCA Y-adapter (available
at electronics stores). Next, remove the wire that is
currently plugged into the AUDIO OUT jack on your
VCR and plug the wire into the unused side of the
RCA Y-adapter. Plug the RCA Y-adapter into the
AUDIO OUT jack on your VCR.
3
Insert the iFIT.com CD or videocassette.
If you are using an iFIT.com CD, insert the CD
into your CD player. If you are using an iFIT.com
videocassette, insert the videocassette into your
VCR.
B
4
ANT. IN
VIDEO AUDIO
IN
RF OUT
CH
3 4
OUT
Press the PLAY button on your CD player or
VCR.
A moment after the button is pressed, your personal trainer will begin guiding you through your
workout. Simply follow your personal trainer’s
instructions. Note: If the Time/Pace display is
flashing, press the Start button or the Speed +
button on the console. The treadmill will not respond to a CD or video program when the
Time/Pace display is flashing.
RCA Y-adapter
Audio
Cable
Select the iFIT.com mode.
Adapter
Wire removed from
AUDIO OUT jack
During the CD or video program, an electronic
“chirping” sound will alert you when the speed
and/or incline of the treadmill is about to change.
CAUTION: Always listen for the “chirp” and be
prepared for speed and/or incline changes. In
some instances, the speed and/or incline may
change before the personal trainer describes
the change.
21
If the speed or incline settings are too high or too
low, you can manually override the settings at any
time by pressing the Speed or Incline buttons on
the console. However, when the next “chirp” is
heard, the speed and/or incline will change to
the next settings of the CD or video program.
• Make sure that the audio cable is properly
connected, that it is fully plugged in, and that
it is not wrapped around a power cord.
• If you are using your portable CD player and
the CD skips, set the CD player on the floor or
another flat surface instead of on the console.
To stop the walking belt at any time, press the
Stop button on the console. The Time/Pace display will begin to flash. To restart the program,
press the Start button or the Speed + button. After
a moment, the walking belt will begin to move at 1
mph. When the next “chirp” is heard, the
speed and incline will change to the next settings of the CD or video program.
• See the instructions near the bottom of page
28.
5
Follow your progress with the displays.
See step 5 on page 12.
6
When the CD or video program ends, the walking
belt will stop and the Time/Pace display will begin
to flash. Note: To use another CD or video program, press the Stop button or remove the key
and go to step 1 on page 21.
Measure your heart rate if desired.
See step 6 on page 13.
7
Turn on the fans if desired.
See step 7 on page 13.
Note: If the speed or incline of the treadmill
does not change when a “chirp” is heard:
8
• Make sure that the iFIT.com indicator is lit and
that the Time/Pace display is not flashing. If
the Time/Pace display is flashing, press the
Start button or the Speed + button on the
console.
When you are finished exercising, remove the
key.
See step 7 on page 14.
CAUTION: Always remove iFIT.com CDs and
videocassettes from your CD player or VCR
when you are finished using them.
• Adjust the volume of your CD player or VCR.
If the volume is too high or too low, the console may not detect the program signals.
22
Hold the handrails, step onto the walking belt, and
begin walking. During the program, an electronic
“chirping” sound will alert you when the speed
and/or incline of the treadmill is about to change.
CAUTION: Always listen for the “chirp” and be
prepared for speed and/or incline changes.
HOW TO USE PROGRAMS DIRECTLY FROM
OUR WEB SITE
To use programs from our Web site, the treadmill must
be connected to your home computer. See HOW TO
CONNECT YOUR COMPUTER on page 20. In
addition, you must have an internet connection and
an internet service provider. A list of specific system
requirements is found on our Web site.
If the speed or incline settings are too high or too
low, you can manually override the settings at any
time by pressing the Speed or Incline buttons on
the console. However, when the next “chirp” is
heard, the speed and/or incline will change to
the next settings of the program.
Follow the steps below to use a program from our
Web site.
1
To stop the walking belt at any time, press the
Stop button on the console. The Time/Pace display will begin to flash. To restart the program,
press the Start button or the Speed + button. After
a moment, the walking belt will begin to move at 1
mph. When the next “chirp” is heard, the speed
and incline will change to the next settings of
the program.
Insert the key fully into the console.
See HOW TO TURN ON THE POWER on page
11.
2
Select the iFIT.com mode.
When the key is inserted, the manual
mode will be selected.
To use a program from
our Web site, press the
iFIT.com button or
press the Select Program button repeatedly until
the indicator above the iFIT.com button lights.
3
Go to your computer and start an internet
connection.
4
Start your web browser, if necessary, and go to
our Web site at www.iFIT.com.
5
Follow the desired links on our Web site to select a program.
When the program ends, the walking belt will stop
and the Time/Pace display will begin to flash.
Note: To use another program, press the Stop
button and go to step 5.
Note: If the speed or incline of the treadmill
does not change when a “chirp” is heard, make
sure that the iFIT.com indicator is lit and that
the Time/Pace display is not flashing. In addition, make sure that the audio cable is properly
connected, that it is fully plugged in, and that it
is not wrapped around a power cord.
8
Follow your progress with the displays.
See step 5 on page 12.
Read and follow the on-line instructions for using a
program.
9
Measure your heart rate if desired.
See step 6 on page 13.
6
Follow the on-line instructions to start the
program.
10 Turn on the fans if desired.
When you start the program, an on-screen countdown will begin.
7
See step 7 on page 13.
11
Return to the treadmill and stand on the foot
rails. Find the clip attached to the key and slide
the clip onto the waistband of your clothes.
When you are finished exercising, remove the
key.
See step 7 on page 14.
When the on-screen countdown ends, the program
will begin and the walking belt will begin to move.
23
THE INFORMATION MODE/DEMO MODE
The console features an information mode that keeps
track of the total number of miles that the walking belt
has moved and the total number of hours that the
treadmill has been operated. The information mode
also allows you to switch the console from miles to
kilometers. In addition, the information mode allows
you to turn on and turn off the demo mode.
To select the information mode, hold down the Stop
button while inserting the key into the console. When
the information mode is selected, the following information will be shown:
The Distance/Laps display
will show the total number of
miles or kilometers that the
walking belt has moved.
console, press the
scent pads into
the recepticals beScent
side the fans.
Pad
Deposit a few
drops of essential
oil onto each
scent pad. As you
exercise, turn on
the fans to circulate the essential
oil throughout your workout area. For information
about REJUVENAIRE scents and scent pads, call
toll-free 1-800-215-7403.
CAUTION: Keep the aromatherapy bottle out of the
reach of children. Essential oil may irritate skin
and is not intended for internal or topical use.
HOW TO ADJUST THE CUSHIONING SYSTEM
The Time/Pace display will
show the total number of
hours that the treadmill has
been used.
An “E” for English miles or
an “M” for metric kilometers
will appear in the Speed display. Press the Speed + button to change the unit of
measurement.
IMPORTANT: The Calories/Fat Calories display
should be blank. If a “d” appears in the display, the
console is in the “demo” mode. This mode is intended
to be used only when a treadmill is displayed in a store.
When the console is in the demo mode, the power cord
can be plugged in, the key can be removed from the
console, and the displays and indicators on the console
will automatically light in a preset sequence; the buttons on the console cannot be operated. If a “d” appears in the Calories/Pulse display when the information mode is selected, press the Speed – button
so the display is blank.
The treadmill features a cushioning system that
reduces the impact as you walk
or run on the
treadmill. To inAdjustable
crease the firmCushion
ness of the walking platform, turn
the adjustment
knob counterclockwise. To decrease the firmness, turn
the knob clockwise. Note: The faster you run on the
treadmill, or the more you weigh, the firmer the
cushioning system should be.
THE OPTIONAL CHEST PULSE SENSOR
An optional chest pulse sensor adds even more
features to the console. The chest pulse sensor provides
hands-free operation and allows the console’s heart
rate programs to be used. To purchase the
optional chest pulse sensor, call toll-free 1-800734-2377.
To exit the information mode, remove the key from the
console.
HOW TO USE THE AROMATHERAPY SYSTEM
To make your workouts more enjoyable, the console
features an aromatherapy system. To use
NordicTrack® REJUVENAIRE™ essential oils with the
24
HOW TO FOLD AND MOVE THE TREADMILL
HOW TO FOLD THE TREADMILL FOR STORAGE
Before folding the treadmill, adjust the incline to the
lowest position. If this is not done, the treadmill may be permanently damaged. Remove the key and unplug the power
cord. CAUTION: You must be able to safely lift 45 pounds
(20 kg) to raise, lower, or move the treadmill.
1. Hold the treadmill with your hands in the locations shown
at the right. CAUTION: To decrease the possibility of injury, bend your legs and keep your back straight. As
you raise the treadmill, make sure to lift with your legs
rather than your back. Raise the treadmill about halfway
to the vertical position.
2. Move your right hand to the position shown and hold the
treadmill firmly. Using your left hand, pull the latch knob to
the left and hold it. Raise the treadmill until the latch pin is
aligned with the indicated hole in the side of the treadmill.
Insert the latch pin into the hole. Make sure that the
latch pin is fully inserted into the hole.
To protect the floor or carpet from damage, place a
mat under the treadmill. Keep the treadmill out of
direct sunlight. Do not leave the treadmill in the storage position in temperatures above 85° Fahrenheit.
Knob
Hole
HOW TO MOVE THE TREADMILL
Before moving the treadmill, convert the treadmill to the storage position as described above. Make sure that the latch
pin is fully inserted into the hole in the side of the treadmill.
1. Hold the handrails as shown and place one foot against a
wheel.
2. Tilt the treadmill back until it rolls freely on the wheels.
Carefully move the treadmill to the desired location. Never
move the treadmill without tipping it back. To reduce
the risk of injury, use extreme caution while moving
the treadmill. Do not attempt to move the treadmill
over an uneven surface.
3. Place one foot on wheel, and carefully lower the treadmill
until it is resting in the storage position.
25
Base
Wheels
HOW TO LOWER THE TREADMILL FOR USE
1. Hold the upper end of the treadmill with your right hand as
shown. Using your left hand, pull the latch knob to the left
and hold it. Pivot the treadmill down until the frame is past
the pin on the latch knob.
Knob
Frame
2. Hold the treadmill firmly with both hands, and lower the
treadmill to the floor. To decrease the possibility of injury, bend your legs and keep your back straight.
26
TROUBLESHOOTING
Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and
follow the steps listed. If further assistance is needed, please call our Customer Service Department tollfree at 1-888-825-2588, Monday through Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays).
PROBLEM: The power does not turn on
SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor
is plugged into a properly grounded outlet (see page 9). Use only a single-outlet surge suppressor
that meets all of the specifications described on page 9. Important: The treadmill is not compatible
with GFCI-equipped outlets.
b. After the power cord has been plugged in, make sure that the key is fully inserted into the console.
c. Check the reset/off circuit breaker located on the
treadmill frame near the power cord. If the switch protrudes as shown, the circuit breaker has tripped. To
reset the circuit breaker, wait for five minutes and
then press the switch to the reset position.
c
Tripped
Reset
PROBLEM: The power turns off during use
SOLUTION: a. Check the reset/off circuit breaker (see the drawing above). If the circuit breaker has tripped, wait
for five minutes and then press the switch to the reset position.
b. Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for five
minutes, and then plug it back in.
c. Remove the key from the console. Reinsert the key fully into the console.
d. If the treadmill still will not run, please call our Customer Service Department, toll-free.
PROBLEM: The displays of the console do not function properly
SOLUTION: a. Remove the key from the console and unplug the
power cord. Carefully tip the Uprights (69) down as
shown in drawing a. Remove the two Front Belly Pan
Screws (3) and the two Screws (83) from the Hood
(23); remember which hole each Screw was removed from. Raise the Uprights back to the vertical
position and carefully remove the Hood.
a
23
69
3
83
Locate the Reed Switch (10) and the Magnet (7) on
the left side of the Pulley (8). Turn the Pulley until the
Magnet is aligned with the Reed Switch. Make sure
that the gap between the Magnet and the Reed
Switch is about 1/8”. If necessary, loosen the Screw
(27) and move the Reed Switch slightly. Retighten the
Screw. Reattach the Hood (23), making sure that the
Screws (3, 83) are inserted into the same holes from
which they were removed. Run the treadmill for a few
minutes to check for a correct speed reading.
27
1/8”
27
10
Top
View
8
7
PROBLEM: The walking belt slows when walked on
SOLUTION: a. Use only a single-outlet surge suppressor that meets all of the specifications described on page 9.
b. If the walking belt is overtightened, treadmill performance may decrease and the walking belt may become damaged. Remove the key and UNPLUG THE
POWER CORD. Using the allen wrench, turn both
rear roller adjustment bolts counterclockwise, 1/4 of a
turn. When the walking belt is properly tightened, you
should be able to lift each side of the walking belt 3 to
4 inches off the walking platform. Be careful to keep
the walking belt centered. Plug in the power cord, insert the key and run the treadmill for a few minutes.
Repeat until the walking belt is properly tightened.
b
3”–4”
Rear Roller Adjustment Bolts
c. If the walking belt still slows when walked on, please call our Customer Service Department, tollfree.
PROBLEM: The walking belt is off-center or slips when walked on
SOLUTION: a. If the walking belt is off-center, remove the key and UNPLUG THE POWER CORD. If the walking belt has
shifted to the left, use the allen wrench to turn the left
rear roller bolt clockwise 1/2 of a turn; if the walking belt
has shifted to the right, turn the left rear roller bolt counterclockwise 1/2 of a turn. Be careful not to overtighten the
walking belt. Plug in the power cord, insert the key, and
run the treadmill for a few minutes. Repeat until the walking belt is centered.
b. If the walking belt slips when walked on, first remove the
key and UNPLUG THE POWER CORD. Using the allen
wrench, turn both rear roller bolts clockwise, 1/4 of a turn.
When the walking belt is correctly tightened, you should
be able to lift each side of the walking belt 3 to 4 inches off
the walking platform. Be careful to keep the walking belt
centered. Plug in the power cord, insert the key, and carefully walk on the treadmill for a few minutes. Repeat until
the walking belt is properly tightened.
a
b
PROBLEM: The incline of the treadmill does not change correctly or does not change when iFIT.com
CDs and videos are played
SOLUTION: a. With the key in the console, press one of the Incline buttons. While the incline is changing, remove the key. After a few seconds, re-insert the key. The treadmill will automatically rise to the
maximum incline level and then return to the minimum level. This will recalibrate the incline.
28
CONDITIONING GUIDELINES
WARNING:
Before beginning this
or any exercise program, consult your physician. This is especially important for individuals over the age of 35 or individuals with preexisting health problems.
The pulse sensor is not a medical device.
Various factors, including your movement,
may affect the accuracy of heart rate readings.
The sensor is intended only as an exercise aid
in determining heart rate trends in general.
The following guidelines will help you to plan your exercise program. For more detailed exercise information, obtain a reputable book or consult your physician.
EXERCISE INTENSITY
Whether your goal is to burn fat or to strengthen your
cardiovascular system, the key to achieving the
desired results is to exercise with the proper intensity.
The proper intensity level can be found by using your
heart rate as a guide. The chart below shows recommended heart rates for fat burning and aerobic exercise.
To find the proper heart rate for you, first find your age
near the bottom of the chart (ages are rounded off to
the nearest ten years). Next, find the three numbers
above your age. The three numbers define your “training zone.” The lower two numbers are recommended
heart rates for fat burning; the higher number is the
recommended heart rate for aerobic exercise.
To measure your heart rate during exercise, use the
pulse sensor on the console.
Fat Burning
To burn fat effectively, you must exercise at a relatively
low intensity level for a sustained period of time.
During the first few minutes of exercise, your body
uses easily accessible carbohydrate calories for en-
ergy. Only after the first few minutes does your body
begin to use stored fat calories for energy. If your goal
is to burn fat, adjust the speed and incline of the treadmill until your heart rate is near the lowest number in
your training zone.
For maximum fat burning, adjust the speed and incline
of the treadmill until your heart rate is near the middle
number in your training zone.
Aerobic Exercise
If your goal is to strengthen your cardiovascular system, your exercise must be “aerobic.” Aerobic exercise
is activity that requires large amounts of oxygen for
prolonged periods of time. This increases the demand
on the heart to pump blood to the muscles, and on the
lungs to oxygenate the blood. For aerobic exercise,
adjust the speed and incline of the treadmill until your
heart rate is near the highest number in your training
zone.
WORKOUT GUIDELINES
Each workout should include the following three parts:
A Warm-up—Start each workout with 5 to 10 minutes
of stretching and light exercise. A proper warm-up increases your body temperature, heart rate and circulation in preparation for exercise.
Training Zone Exercise—After warming up, increase
the intensity of your exercise until your pulse is in your
training zone for 20 to 60 minutes. (During the first few
weeks of your exercise program, do not keep your
pulse in your training zone for longer than 20 minutes.)
Breathe regularly and deeply as you exercise—never
hold your breath.
A Cool-down—Finish each workout with 5 to 10 minutes of stretching to cool down. This will increase the
flexibility of your muscles and will help prevent post-exercise problems.
EXERCISE FREQUENCY
To maintain or improve your condition, complete three
workouts each week, with at least one day of rest between workouts. After a few months, you may complete up to five workouts each week if desired. The key
to success is to make exercise a regular and enjoyable
part of your everyday life.
29
PART LIST—Model No. NTL12840
R1003A
To locate the parts listed below, see the EXPLODED DRAWING attached in the center of this manual.
Key No. Qty.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15*
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
2
2
2
1
2
2
1
1
4
1
4
1
1
1
1
1
1
1
1
5
1
1
1
1
1
1
12
1
1
1
1
1
2
6
1
1
1
1
1
2
1
1
1
4
6
2
8
1
4
4
Description
Key No. Qty.
Foot Rail Insert
Foot Rail
Front Belly Pan Screw
Left Foot Rail Cap
Frame Pivot Bolt
Frame Pivot Spacer
Magnet
Front Roller/Pulley
Frame Pivot Nut
Reed Switch/Sensor Wire
U-nut
Reed Switch Clip
Lift Frame
Walking Belt
Motor Assembly
Motor
Pulley/Flywheel/Fan
Motor Belt
Motor Pivot Nut
Motor Tension Nut
Incline Motor Bolt (Top)
Motor Pivot Bolt
Hood
Incline Motor Bolt (Lower)
Motor Tension Bolt
Hole Plug
Screw
Transformer
Controller
Electronics Plate
Motor Controller Wire
Front Roller Adj. Bolt
2” Screw
Roller Washer
Latch Knob Spacer
Incline Motor
Incline Motor Stop
Motor Belly Pan
Audio Wire Nut
Static Decal
Console Ground Wire
Power Cord
Reset/Off Circuit Breaker
Spring Bolt
Belt Guide Screw
Belt Guide
1” Tek Screw
Motor Star Washer
Platform Nut
Spring Nut
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80*
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
30
1
1
2
4
2
2
1
1
2
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
2
4
4
2
1
1
1
8
1
1
1
1
1
1
25
2
5
2
2
2
1
1
1
6
6
Description
Right Foot Rail Cap
Walking Platform
4” Bolt
Platform Bolt
Spring Pad
Spring
Ground Wire
Rear Endcap (Right)
Rear Roller Adj. Bolt
Warning Decal
Allen Wrench
Rear Roller
Audio Wire
Catch
Left Fan Housing
Console Frame
Spring Pad Screw
Latch Knob
Upright
Latch Knob Sleeve
Spring
Latch Pin Collar
Pin Clip
Latch Pin
Filter Wire
Pulse Grip
Handrail Spacer
4 1/2” Bolt
Upright Endcap
Latch Assembly
Console Base
Console
Screw
Key/Clip
iFIT.com Wire
Jack
Aromatherapy Kit
Console Back
Releaseable Tie
Console Screw
Cable Tie Clamp
8” Cable Tie
Lift Pivot Bolt
Wheel Bolt
Wheel
Rear Endcap (Left)
Grommet
Upright Wire Harness
Base Pad
3/4” Screw
Key No. Qty.
101
102
103
104
105
106*
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
1
2
2
2
1
2
2
1
1
1
1
2
2
1
1
1
1
2
2
1
1
1
1
2
2
1
Description
Key No. Qty.
Motor Washer
Extension Leg
Extension Cap
Incline Warning Decal
Right Foam Trim
Extension Leg Assembly
Fan
Book Holder
Power Cord Grommet
Frame
Left Rear Foam Trim
Roller Star Washer
Spring Plate
Left Front Foam Trim
Left Cup Holder
Right Cup Holder
Right Fan Housing
Handrail w/Foam
Handrail Foam
Left Rear Foot
Right Rear Foot
Upper Handrail w/Foam
Upper Handrail Foam
Handrail Washer
3” Bolt
Right Inside Housing
127
128
129
130
131
132
133
134
135
136
137
138
139
#
#
#
#
#
#
#
#
1
4
2
4
2
2
2
1
1
1
1
1
2
1
1
1
1
1
1
1
1
Description
Right Outside Housing
Cushion Adj. Screw
Gear Rack
Cushion Adj. Housing Screw
Cushion Adj. Pin
Cushion Adj. Wheel
Cushion Adj. Gear
Cushion Adj. Rod
Cushion Adj. Knob
Cushion Adj. Screw
Left Outside Housing
Right Inside Housing
Spring Spacer
14” Blue Wire, 2F
12” Blue Wire, 2F
4” Blue Wire, M/F
8” Black Wire, M/F
12” Green Wire, 2 Ring
4” Green Wire, F/Ring
10” Red Wire, M/F
User's Manual
*Includes all parts shown in box
#These parts are not illustrated
Specifications are subject to change without notice.
ORDERING REPLACEMENT PARTS
To order replacement parts, call our Customer Service Department toll-free at 1-888-825-2588, Monday through
Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays). When ordering parts, please be prepared to give
the following information:
• the MODEL NUMBER OF THE PRODUCT (NTL12840)
• the NAME OF THE PRODUCT (NordicTrack® C2250 treadmill)
• the SERIAL NUMBER OF THE PRODUCT (see the front cover of this manual)
• the KEY NUMBER AND DESCRIPTION OF THE PART(S) (see the PART LIST on pages 30 and 31 and the
EXPLODED DRAWING attached in the center of this manual)
31
59
112
34
61
83
137
96
130
128
23
33
110
60
138
54
130
120
129
59
49
112 83
34
111
45
14
2
64
33
121
58
62
54
114
46
49
45
49
27
57
54
5
1
6
128
129
130
2
1
55
7
90
8
67
52
4
67
10
9
56
44
50
56
34
105
9
45
37
139
44
132
131
9
25
83
101
36
46
24
133
34
20
20
113
16
13 48
113
90
12
27
15*
17
127
126
51
139
49
54
18
19
9
22
134
6
32
100
21
132
38
5
20
133
100
75
131
83
28
63
3
136
135
27
27
100
39
40 26
27
30
27
29
43
109
42
85
3
31
86
EXPLODED DRAWING—Model No. NTL12840
R1003A
65
76
87
66
90
90
90
107
83
90
90
90
90
76
90
81
90
90
88
115
83
83
82
90
90
90
90
90
106*
83
108
103
40
90
102
90
47
99
117
90
107
80*
116
68
90
41
104
35
84
47
53
106*
99
93
69
103
94
72
70
71
102
47
99
74
77
73
79
47
99
95
124
125
78
27
20
104
98
47
99
97
122
53
123
92
119
20
47
99
77
79
93
95
78
94
91
100
89
11
118
11
EXPLODED DRAWING—Model No. NTL12840
R1003A
LIMITED WARRANTY
WHAT IS COVERED—The entire NordicTrack® C2250 treadmill (“Product”) is warranted to be free of all defects in material and workmanship.
WHO IS COVERED—The original purchaser or any person receiving the Product as a gift from the original purchaser.
HOW LONG IS IT COVERED—ICON Health & Fitness, Inc. (“ICON”), warrants the motor for three years after the date
of purchase. The belt and deck are covered for two years after the date of purchase. All mechanical components are
covered for two years after the date of purchase. All electrical components are covered for two years after the date of
purchase. Labor is covered for one year. The hood, covers, belly pan, and decals are covered for six months after the
date of purchase.
WHAT WE DO TO CORRECT COVERED DEFECTS—We will ship to you, without charge, any replacement part or
component, providing the repairs are authorized by ICON first and are performed by an ICON trained and authorized
service provider, or, at our option, we will replace the Product.
WHAT IS NOT COVERED—Any failures or damage caused by unauthorized service, misuse, accident, negligence, improper assembly or installation, alterations, modifications without our written authorization or by failure on your part to
use, operate, and maintain as set out in your User’s Manual (“Manual”). This warranty does not extend to products used
for commercial or rental purposes or to products used as store display modules.
WHAT YOU MUST DO—Always retain proof of purchase, such as your bill of sale; store, operate, and maintain the
Product as specified in the Manual; notify our Customer Service Department of any defect within 10 days after discovery of the defect; as instructed, return any defected part for replacement or, if necessary, the entire product, for repair.
USER’S MANUAL—It is VERY IMPORTANT THAT YOU READ THE MANUAL before operating the Product.
Remember to do the periodic maintenance requirements specified in the Manual to assure proper operation and your
continued satisfaction.
HOW TO GET PARTS AND SERVICE—Simply call our Customer Service Department at 1-888-825-2588 and tell them
your name and address and the serial number of your Product. They will tell you how to get a part replaced, or if necessary, arrange for service where your Product is located or advise you how to ship the Product for service. Before shipping, always obtain a Return Authorization Number (RA No.) from our Customer Service Department; securely pack
your Product (save the original shipping carton if possible); put the RA No. on the outside of the carton and insure the
product. Include a letter explaining the product or problem and a copy of your proof of purchase if you believe the service is covered by warranty.
ICON is not responsible or liable for indirect, special or consequential damages arising out of or in connection with the
use or performance of the product or damages with respect to any economic loss, loss of property, loss of revenues or
profits, loss of enjoyment or use, costs of removal, installation or other consequential damages of whatsoever nature.
Some states do not allow the exclusion or limitation of incidental or consequential damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of merchantability
or fitness for a particular purpose is limited in its scope and duration to the terms set forth herein. Some states do not
allow limitations on how long an implied warranty lasts. Accordingly, the above limitation may not apply to you.
No one is authorized to change, modify or extend the terms of this limited warranty.
This warranty gives you specific legal rights and you may have other rights which vary from state to state.
ICON HEALTH & FITNESS, INC., 1500 S. 1000 W., LOGAN, UT 84321-9813
Part No. 206287 R1003A
Printed in USA © 2003 ICON Health & Fitness, Inc.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement