Windows CE Mobile Computer 9500CE Version 2.07

Windows CE Mobile Computer
9500CE
Version 2.07
Copyright © 2007~ 2008 CIPHERLAB CO., LTD.
All rights reserved
The software contains proprietary information of CIPHERLAB CO., LTD.; it is provided
under a license agreement containing restrictions on use and disclosure and is also
protected by copyright law. Reverse engineering of the software is prohibited.
Due to continued product development this information may change without notice. The
information and intellectual property contained herein is confidential between CIPHERLAB
and the client and remains the exclusive property of CIPHERLAB CO., LTD. If you find
any problems in the documentation, please report them to us in writing. CIPHERLAB
does not warrant that this document is error-free.
No part of this publication may be reproduced, stored in a retrieval system, or
transmitted in any form or by any means, electronic, mechanical, photocopying,
recording or otherwise without the prior written permission of CIPHERLAB CO., LTD.
For product consultancy and technical support, please contact your local sales
representative. Also, you may visit our web site for more information.
The CipherLab logo is a registered trademark of CIPHERLAB CO., LTD.
Microsoft, Windows, and the Windows logo are registered trademarks of Microsoft
Corporation in the United States and/or other countries.
Bluetooth is a trademark of Bluetooth SIG, Inc., U.S.A.
Other product names mentioned in this manual may be trademarks or registered
trademarks of their respective companies and are hereby acknowledged.
The editorial use of these names is for identification as well as to the benefit of the
owners, with no intention of infringement.
CIPHERLAB CO., LTD.
Website: http://www.cipherlab.com
IMPORTANT NOTICES
FOR USA
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
FOR CANADA
This digital apparatus does not exceed the Class B limits for radio noise emissions from
digital apparatus as set out in the interference-causing equipment standard entitled
"Digital Apparatus," ICES-003 of Industry Canada.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
Cet appareil numerique respecte les limites de bruits radioelectriques applicables aux
appareils numeriques de Classe B prescrites dans la norme sur le material brouilleur:
"Appareils Numeriques," NMB-003 edictee par l'Industrie.
FOR HAND-HELD PRODUCT WITH RF FUNCTIONS
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20
cm between the radiator & your body. It only operated in hand-held used.
If you only transfer data to Host by WLAN/Bluetooth, please keep the minimum distance
20 cm between machine & your body.
FOR PRODUCT WITH LASER
Per FDA and IEC standards, the scan engines described in this manual are not given a
laser classification. However, the following precautions should be observed:
CAUTION
This laser component emits FDA / IEC Class 2 laser light at the exit port. Do not
stare into beam.
SAFETY PRECAUTIONS
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.
DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.
The use of any batteries or charging devices, which are not originally sold or
manufactured by CipherLab, will void your warranty and may cause damage to
human body or the product itself.
DO NOT disassemble, incinerate or short circuit the battery.
DO NOT expose the scanner or the battery to any flammable sources.
For green-environment issue, it's important that batteries should be recycled in a
proper way.
Under no circumstances, internal components are self-serviceable.
The charging and communication cradle uses an AC power adaptor. A socket outlet
shall be installed near the equipment and shall be easily accessible. Make sure there
is stable power supply for the mobile computer or its peripherals to operate properly.
CARE & MAINTENANCE
This mobile computer is intended for industrial use. The mobile computer is rated IP
64, however, it may do damage to the mobile computer when being exposed to
extreme temperatures or soaked wet.
When the body of the mobile computer gets dirty, use a clean and wet cloth to wipe
off the dust. DO NOT use/mix any bleach or cleaner. Always keep the LCD dry.
For a liquid crystal display (LCD) or touch screen, use a clean, non-abrasive, lint-free
cloth to wipe dust off the screen. DO NOT use any pointed or sharp object to move
against the surface.
If you want to put away the mobile computer for a period of time, download the
collected data to a host computer, and then take out the battery pack. Store the
mobile computer and battery pack separately.
When the mobile computer resumes its work, the main and backup batteries will take
a certain time to become fully charged.
If you shall find the mobile computer malfunctioning, write down the specific scenario
and consult your local sales representative.
RELEASE NOTES
Version
Date
Notes
2.07
July 09, 2008
Modified: section 1.7 Communications – Illustrations updated
2.06
June 30, 2008
Modified: Appendix IV 2D Scan Engine – Image Capture
Modified: section 4.3.4 Notifications – Remove warning beep
New: sections 2.1.2 and 3.2.4 – Wi-Fi status icon with dynamic
bars for wireless signal strength
Modified: section 2.5.3 – Auto Run examples
Modified: section 4.3 – UI of ReaderConfig.exe changed
2.05
2.04
Apr. 16, 2008
Mar. 04, 2008
2.03
Jan. 02, 2008
2.02
Nov. 22, 2007
New: Supports 802.11b/g module for wireless networking
Modified: sections 1.1.3, 2.1.1 & 2.1.2 Battery icons
Modified: section 1.3.4 Task Key
Modified: section 3.2.2, 3.2.3 & 4.1 Screenshots of Wireless Power
Manager updated
Modified: section 2.5.3 Auto Run – AutoRun.ini and cabinet files
Modified: section 4.3.3 Data Output – Keyboard Emulation options
include “Local machine”, “RDP server”
Modified: Appendix II~IV – Update default values of ReaderConfig
New: Charging the Battery – 4-Slot Battery Charger
New: sections 1.1.3 and 2.1.2 – Battery charge icon with dynamic
bars
Modified: section 4.2 Bluetooth Manager – Remove [Exit] button
New: Appendix III, IV – AIM Code ID
Modified: section 4.5.4 Backup file version & insufficient memory
issues (Version 1.00.0010 & 1.00.0011)
Modified: Appendix II~IV – default values updated
2.01
Oct. 03, 2007
Minor changes
2.00
July 10, 2007
New Word template applied
1.10
June 20, 2007
Modified: section 5.5 Backup Utility - Backup directory & Auto
Restore settings
1.09
June 11, 2007
New: section 3.2.3 Auto Run
Modified: sections 5.3.2~4 - General tab > Data Output >
Windows Message & Event
Modified: section 5.2 - Bluetooth Manager capable of ActiveSync
1.08
1.07
Feb. 26, 2007
Dec. 26, 2006
New: section 5.5 Backup Utility
New: Appendix II ~ IV
Modified: section 4.2 Connections
Modified: section 5.3 ReaderConfig settings
Modified: Appendix I - Scan Engine Settings
Modified: section 1.5.6 - Status LED: Remove indication for “Low
Battery”
1.06
Dec. 22, 2006
Modified: section 1.5.4 - Task key undefined for OS version 1.0
and later
1.05
Dec. 12, 2006
Modified: section 4.2.2 - GPRS Properties: Specify AP Name
1.04
Nov. 03, 2006
1.03
Oct. 27, 2006
1.02
Oct. 16, 2006
Modified: section 3.4 - USB driver will be installed automatically
1.01
Sep. 27, 2006
Initial release
Modified: section 3.3 - OS Update steps 7 ~9
Modified: Supports GPRS functionality via CF Type II slot if
installed (No GSM!)
CONTENTS
IMPORTANT NOTICES ...................................................................................................................... - 3 For USA .......................................................................................................................................... - 3 For Canada .................................................................................................................................... - 3 For Hand-held Product with RF Functions ................................................................................... - 3 For Product with Laser .................................................................................................................. - 4 Safety Precautions ........................................................................................................................ - 4 Care & Maintenance ..................................................................................................................... - 4 RELEASE NOTES .............................................................................................................................. - 5 INTRODUCTION .................................................................................................................................... 1
Getting Familiarized with 9500CE ................................................................................................... 2
Installing the Hand Strap............................................................................................................. 3
Installing the Pistol Grip............................................................................................................... 4
Charging the Battery .................................................................................................................... 5
Dimensions........................................................................................................................................ 6
Features............................................................................................................................................. 7
Inside the Package............................................................................................................................ 8
Accessories........................................................................................................................................ 8
USING 9500CE MOBILE COMPUTER .................................................................................................. 9
1.1 Battery ......................................................................................................................................... 9
1.1.1 Installing the Battery.......................................................................................................... 9
1.1.2 Charging the Battery ........................................................................................................11
1.1.3 Understanding the Battery Icons ....................................................................................11
1.1.4 Power Management.........................................................................................................12
1.2 Memory ..................................................................................................................................... 13
1.2.1 Caution of Data Loss........................................................................................................13
1.2.2 Checking the Storage Space ........................................................................................... 13
1.2.3 Inserting the SD or CF Card .............................................................................................14
1.3 Keypad ...................................................................................................................................... 16
1.3.1 Using the Keypad ............................................................................................................. 16
1.3.2 Alpha Key..........................................................................................................................17
1.3.3 Function Key..................................................................................................................... 17
1.3.4 Task Key ........................................................................................................................... 18
1.4 Touch Screen ............................................................................................................................ 19
1.4.1 Adjusting the Backlight ....................................................................................................19
1.4.2 Re-calibrating the Screen ................................................................................................20
1.5 Notifications.............................................................................................................................. 21
1.5.1 Status LED ........................................................................................................................21
1.5.2 Audio ................................................................................................................................. 21
1.5.3 Vibrator ............................................................................................................................. 21
1.6 Data Capture.............................................................................................................................22
9500CE Mobile Computer Reference Manual
1.7 Communications....................................................................................................................... 23
1.7.1 Using the Cradle ............................................................................................................... 23
1.7.2 Using Wireless Networks .................................................................................................24
LEARNING WINDOWS CE BASICS...................................................................................................... 25
2.1 Getting Started .........................................................................................................................25
2.1.1 Desktop............................................................................................................................. 26
2.1.2 Taskbar ............................................................................................................................. 27
2.1.3 Start Menu........................................................................................................................29
2.1.4 Input Methods .................................................................................................................. 30
2.2 Finding out the Capabilities of Your Mobile Computer...........................................................31
2.2.1 Changing Device Name ...................................................................................................31
2.2.2 Understanding Device Configuration ..............................................................................31
2.3 Using ActiveSync....................................................................................................................... 33
2.3.1 Synchronization with Your Computer..............................................................................33
2.3.2 Add/Remove Programs....................................................................................................33
2.3.3 Backup/Restore ...............................................................................................................34
2.4 Managing Programs ................................................................................................................. 36
2.4.1 Quick Launch a Program .................................................................................................36
2.4.2 Create a Folder................................................................................................................. 38
2.4.3 Switch among Programs and Desktop ...........................................................................39
2.4.4 Exit a Program ..................................................................................................................39
2.5 System Reset & Auto Run ........................................................................................................40
2.5.1 Software Reset (Warm Reboot).......................................................................................40
2.5.2 Hardware Reset (Cold Reboot)........................................................................................40
2.5.3 Auto Run ........................................................................................................................... 40
2.6 Upgrading OS Image.................................................................................................................42
PERSONALIZING 9500CE MOBILE COMPUTER................................................................................ 43
3.1 Changing System Settings .......................................................................................................43
3.2 Changing Connection Settings.................................................................................................47
3.2.1 USB Connection ...............................................................................................................49
3.2.2 GPRS ................................................................................................................................. 50
3.2.3 Ethernet (LAN Card AX88772) ........................................................................................ 53
3.2.4 WLAN................................................................................................................................. 54
3.2.5 BTPAN ............................................................................................................................... 57
USING APPLICATIONS........................................................................................................................ 59
4.1 Wireless Power Manager .........................................................................................................60
4.2 Bluetooth Manager................................................................................................................... 61
4.2.1 Bluetooth Profiles Supported .......................................................................................... 61
4.2.2 Bluetooth Toolbar.............................................................................................................61
4.2.3 Starting Bluetooth Services .............................................................................................65
4.2.4 Discovering Bluetooth Devices........................................................................................65
4.2.5 Pairing ............................................................................................................................... 66
4.2.6 Connecting........................................................................................................................67
4.3 Reader Configuration Utility .....................................................................................................72
4.3.1 Checking the Reader Status............................................................................................73
4.3.2 RFID Reader Settings....................................................................................................... 73
4.3.3 Data Output ......................................................................................................................74
9500CE Mobile Computer Reference Manual
4.3.4 Notifications (for Good Read)..........................................................................................75
4.3.5 Symbology Settings..........................................................................................................76
4.4 Inbox .......................................................................................................................................... 77
4.4.1 Creating an E-mail Box.....................................................................................................77
4.4.2 Synchronizing Inbox .........................................................................................................79
4.5 Backup Utility ............................................................................................................................ 80
4.5.1 Managing the Registry ..................................................................................................... 80
4.5.2 Getting Ready for Backing up Files ................................................................................. 81
4.5.3 Backing up Files ...............................................................................................................81
4.5.4 Using Backups for Restore ..............................................................................................83
SPECIFICATIONS ................................................................................................................................ 85
Platform, Processor & Memory ......................................................................................................85
Communications & Data Capture ..................................................................................................85
Electrical Characteristics ................................................................................................................86
Physical Characteristics ..................................................................................................................86
Environmental Characteristics ....................................................................................................... 87
Programming Support.....................................................................................................................87
Accessories...................................................................................................................................... 88
SCAN ENGINE SETTINGS................................................................................................................... 89
Symbologies Supported .................................................................................................................. 90
RFID Tags Supported ...................................................................................................................... 92
CCD/LASER SCAN ENGINE................................................................................................................ 93
Reader Settings Table.....................................................................................................................93
Symbology Settings Table...............................................................................................................94
LR/ELR LASER SCAN ENGINE ........................................................................................................... 99
Reader Settings Table.....................................................................................................................99
Symbology Settings Table.............................................................................................................100
AIM Code ID – Code Characters..............................................................................................103
AIM Code ID – Modifier Characters.........................................................................................104
2D SCAN ENGINE.............................................................................................................................105
Reader Settings Table...................................................................................................................105
Symbology Settings Table.............................................................................................................106
AIM Code ID – Code Characters..............................................................................................110
AIM Code ID – Modifier Characters.........................................................................................111
INTRODUCTION
Delivered in the same form factor of 9500PPC Mobile Computer running Windows Mobile
2003SE, 9500CE Mobile Computer is the newest member to the Mobile Computer family.
As suggested by its model designation, it is designed to run Windows CE 5.0, and
therefore, allows more flexibility in customization of applications.
CipherLab has integrated powerful utilities for data collection, processing, and
transmission. Its large color transflective TFT display guarantees ease in reading in all
lighting conditions. Built-in with Bluetooth and 802.11b/g technologies, 9500CE Mobile
Computer also allows for GPRS connectivity, and therefore, delivers a total wireless
solution.
9500CE Mobile Computer is robust in construction to meet industry grade requirements,
and has been found durable and resistant to shock, water, and dust. It is specifically
designed for all-day, everyday use as well as for data-intensive applications in harsh
environments.
This manual serves to guide you through how to install, configure, and operate the
mobile computer. The Care & Maintenance section is specifically prepared for those who
are in charge of taking care of the mobile computer.
We recommend you to keep one copy of the manual at hand for quick reference or
maintenance purposes. To avoid any improper disposal or operation, please read the
manual thoroughly before use.
Thank you for choosing CipherLab products!
1
9500CE Mobile Computer Reference Manual
GETTING FAMILIARIZED WITH 9500CE
Figure 1: Overview
2
Introduction
INSTALLING THE HAND STRAP
The hand strap is ideal for one-handed operation, which requires safe and convenient
hold of the mobile computer. Always make sure the hand strap is well hooked and
screwed to the back of the mobile computer. When the hand strap is desired, install it to
the mobile computer by following these steps:
1) Place the mobile computer face down on a flat and clean surface.
2) Screw one end of the hand strap to the shield-like cover on the back of the mobile
computer.
3) Insert and hook the other end of the hand strap to the bottom of the mobile
computer.
4) Make sure the hand strap is securely attached to the mobile computer.
5) Adjust the length of the hand strap to suit your handbreadth.
Figure 2: Installing the Hand Strap
3
9500CE Mobile Computer Reference Manual
INSTALLING THE PISTOL GRIP
This contoured pistol grip enables intuitive trigger-and-scan operation, which is very
helpful in scan intensive applications. When a pistol grip is necessary, install it to the
mobile computer by following these steps:
1) Place the mobile computer face down on a flat and clean surface.
2) Remove the shield-like cover on the back of the mobile computer by unscrewing.
If the hand strap is installed, remove it first. Keep the cover and screws for future use
when the pistol grip is not desired.
3) Connect the power connector from the pistol grip to the receptacle on the mobile
computer.
4) Screw the pistol grip to the back of the mobile computer.
5) Make sure all screws are tightened up.
6) Turn on the mobile computer and test the trigger while running ReaderConfig.exe.
Figure 3: Installing the Pistol Grip
4
Introduction
CHARGING THE BATTERY
You can use a cradle or charger to charge the Mobile Computer and/or its battery. Below
is the 4-Slot Battery Charger for 9500CE. For the Charging & Communication Cradle,
refer to 1.7 Communications.
Warning:
It is recommended that the charging devices be operated at room
temperature (18°C to 25°C) for optimal performance. The charging devices
will not charge the battery when the temperature exceeds 40°C.
1) The Battery Charger can be mounted on table or wall. Drill two holes (centers spaced
160 millimeters apart), secure the two supplied screws, and mount the Battery
Charger by sliding over screws.
2) Slide the battery into the battery compartment at a proper angle, with contacts facing
to back.
3) Connect the power supply cord to the power receptacle on the charger.
4) Connect the other end of the power supply cord to a suitable power outlet.
5) Press the power switch on, and the Battery Charger’s LED will be red.
6) While charging, the LED of the battery compartment will be red. When fully charged,
the LED will be green.
Figure 4: 4-Slot Battery Charger
LED
Status
Meaning
Power
Solid red
Power ON
Off
Power OFF
Solid red
Charging battery
Solid green
Charging done
Flashing red and green
Error occurs
Off
Battery not ready
Battery Charging
5
9500CE Mobile Computer Reference Manual
DIMENSIONS
Figure 5: Dimensions
6
Introduction
FEATURES
Ergonomic design - ruggedized yet streamlined, with hand strap for secure hold.
Built tough to survive drop test and sealed against moisture/dust to industrial
standard IP 64.
Microsoft Windows CE 5.0 operating system, 520 MHz Intel PXA270 processor
128 MB non-volatile NAND flash memory to store OS and software programs
(part of the free space is used as a storage card called DiskOnChip)
128 MB SDRAM to store and run programs, as well as store program data
One CompactFlash (CF) Type II expansion slot for memory card and peripherals
(when no GPRS card is present)
One Secure Digital (SD) expansion slot for memory card
Dual mode support - One scan engine (integrated barcode scanner/imager) plus one
RFID reader
Total wireless solution - connectivity includes Bluetooth, 802.11b/g and GPRS.
A 3.5" color transflective TFT display delivers excellent visibility in all lighting
conditions.
Programmable feedback includes speaker and vibrator.
Built-in power tools include Reader Configuration Utility, Backup Utility, etc.
Terminal Emulation client for VT100/220 and IBM 5250 enables a quick link to any
backend database.
Application Generator (AG*.exe for desktop PC) enables easy customization of data
collection applications.
Programming support includes Reader DLL and System API.
Accessories and peripherals include pistol grip, international AC charging cradle, etc.
7
9500CE Mobile Computer Reference Manual
INSIDE THE PACKAGE
The following items are included in the package. Save the box and packaging material for
future use in case you need to store or ship the mobile computer.
9500CE Mobile Computer
Rechargeable Li-ion battery pack
Stylus
Hand Strap
Software & Manual CD
Note: For battery charging, you will need to purchase a charging cradle separately.
ACCESSORIES
Rich choices of optional accessories are available for you to enhance the total
performance of the mobile computer.
8
Pistol Grip (detachable)
Belt Holster
Protective Cover
Memory Card, SD or CF card (if no GPRS card in the CF slot)
Spare rechargeable Li-ion battery
4-Slot Battery Charger
Charging & Communication Cradle
Vehicle Cradle
Travel Charger
Chapter 1
USING 9500CE MOBILE COMPUTER
This chapter explains the features and usage of 9500CE Mobile Computer.
IN THIS CHAPTER
1.1
1.2
1.3
1.4
1.5
1.6
1.7
Battery....................................................................... 9
Memory.................................................................... 13
Keypad..................................................................... 16
Touch Screen ............................................................ 19
Notifications.............................................................. 21
Data Capture ............................................................ 22
Communications ........................................................ 23
1.1 BATTERY
Main Battery
9500CE Mobile Computer is powered by a rechargeable 3.7 V/4000 mAh Li-ion
battery pack, and it takes approximately 4 hours to fully charge it. However, the
charging time may vary by working condition. During normal operation, the mobile
computer can work for up to 21 hours in batch mode. For non-stop power on the road,
you may purchase a spare battery pack.
Backup Battery
The backup battery on the main board takes charge when the main battery is
removed or drained out. When fully charged, the 3.7 V/110 mAh rechargeable
Lithium button cell helps retain data in SRAM and maintain the system running in
suspend mode for at least 6 hours without the main battery. In the meantime, you
have to replace the main battery as soon as possible.
1.1.1 INSTALLING THE BATTERY
When you first receive the package, the rechargeable functionality of the backup battery
is turned off. It is controlled by a DIP switch inside the battery compartment as shown
below.
For shipping and storage purposes, save the mobile computer and the main battery in
separate packages, and slide the DIP switch to the OFF position (to your right). This will
keep both batteries in good condition for future use.
Note: Any improper handling may reduce the battery life.
1) Hold the mobile computer still as shown below.
9
9500CE Mobile Computer Reference Manual
2) Use the stylus (or a sharp-pointed object, such as a pencil) to slide the DIP switch to
the ON position (to your left). Now the internal backup battery can be charged by the
main battery.
3) Slide the battery pack into the battery compartment at a proper angle (30°~45°) so
that the tabs on the bottom of the battery are hooked in the grooves of the
compartment. Make sure that the battery is snugly fit into the compartment.
4) Slide the battery latch to lock the battery in the compartment.
Figure 6: Adjusting DIP Switch & Installing the Main Battery
10
Chapter 1
Using 9500CE Mobile Computer
1.1.2 CHARGING THE BATTERY
The main and backup batteries may not be charged to full for shipment. When you first
receive the package, you will need to charge batteries to full before using the mobile
computer.
Note: To charge the batteries to full, it requires approximately 8 hours for the first time.
After the initial charging, it takes only 4 hours to charge the batteries to full.
Because the internal backup battery is constantly charged from the main battery, the
initial charging requires installing the battery pack to the mobile computer and then
seating the mobile computer in the cradle for charging. This will have both the main and
backup batteries charged at the same time. To charge the backup battery, make sure
that you slide the DIP switch inside the battery compartment to the ON position.
Note: For a new battery, make sure it is fully charged before use. Always prepare a
spare battery pack, especially when you are on the road.
1.1.3 UNDERSTANDING THE BATTERY ICONS
The battery pack is the only power source for the mobile computer to work. It also
charges the backup battery on the main board so that the data stored in SRAM can be
retained properly. Therefore, when the main battery charge goes low, you need to
replace the battery pack with a charged one or charge it as soon as possible. Most of all,
always save data before it is too late; you should backup important data on a regular
basis.
Double-tap a battery icon so that you can quickly access the [Power Properties] dialog
box.
Battery Status Icons
Description
Battery charge remaining in the main battery – The more bars, the more
power in the main battery.
Main battery is ready for charging.
Main battery charge becomes low and needs charging.
Main battery charge becomes very low and needs charging immediately.
Backup battery charge becomes low and needs charging.
Backup battery charge becomes very low and needs charging
immediately.
Warning:
Data loss may occur with SRAM during low battery condition. Always save
data before running out of power or keep a fresh battery for replacement.
11
9500CE Mobile Computer Reference Manual
1.1.4 POWER MANAGEMENT
For any portable device, power management is a critical issue especially when you are on
the road. Below are some tips to help you save battery power.
Warning:
Using backlight, wireless connectivity, and peripherals while on battery
power will substantially reduce battery power.
To speed up charging the mobile computer, turn off the mobile computer and seat it
in the cradle.
Bring a second battery pack on the road.
Stop wireless connectivity, Bluetooth, 802.11b/g or GPRS that is not in use. Refer to
4.1 Wireless Power Manager.
Go to Start > Settings > Control Panel and double-tap the Display icon. Refer to
1.4.1 Adjusting the Backlight.
Go to Start > Settings > Control Panel and double-tap the Power icon (below).
1. In the Battery tab (left below), you can always monitor the charging status.
2. Tap the Schemes tab (right above).
3. Select the desired power scheme and options for suspending operation when not
in use. The system can be set to three different states to conserve power:
ƒ
User Idle state
ƒ
System Idle state
ƒ
Suspend state
The time choices represent the amount of time that must pass before the system
will switch to the next power conservation state.
12
Chapter 1
Using 9500CE Mobile Computer
1.2 MEMORY
Read-only Memory (ROM)
128 megabytes flash memory for storing OS (Windows CE 5.0) and custom
application programs. Yet a small portion of the memory is referred to as DiskOnChip,
which can store data and programs that you wish to retain even after hardware reset.
Random-access Memory (RAM)
64 or 128 megabytes SDRAM for storing and running programs, as well as storing
program data. Its contents will be retained by the backup battery.
Expansion Slot
The mobile computer is equipped with two card slots, one SD and one CompactFlash
Type II. You may upgrade memory by inserting an optional SD or CF memory card.
1.2.1 CAUTION OF DATA LOSS
When the main battery is removed or drained, the backup battery on the main board is
to retain the contents of SRAM and maintain the OS in suspend mode for at least 6 hours,
on condition that the backup battery has already been fully charged.
If you want to put away the mobile computer for a couple of days, you should be aware
that data loss occurs when both the main and backup batteries discharge completely.
Therefore, it is necessary to backup data and files before putting away the mobile
computer!
1.2.2 CHECKING THE STORAGE SPACE
Go to Start > Settings > Control Panel and double-tap the System icon.
1. In the Memory tab, it displays the current capacity and usage of the onboard
SDRAM, 128 MB.
13
9500CE Mobile Computer Reference Manual
2. You may tap, hold, and drag the slider to re-allocate the memory.
SDRAM
Storage Memory (left)
Program Memory (right)
128 MB
onboard
It refers to the memory allocated
for file and data storage.
It refers to the memory allocated
for running programs.
Double-tap My Device on the desktop, and then tap and hold the DiskOnChip icon.
Select Properties from the pop-up menu. In the Properties tab, it displays the current
capacity and usage of DiskOnChip.
Note: The DiskOnChip is part of the onboard 128 MB flash memory. Because the flash
memory is non-volatile, data or programs stored in DiskOnChip will not be erased
after hardware reset.
Go to Start > Settings > Control Panel and double-tap the Storage Manager icon.
Here provides a tool for administrators to reformat the DiskOnChip folder or storage
card (SD or CF).
Warning:
This tool is for the use of system administrators only. Everything on the
storage device will be permanently erased after reformatting.
1.2.3 INSERTING THE SD OR CF CARD
When you need to expand memory or add a peripheral, take the following steps to install
the CF or SD card to the mobile computer:
1) Press the [Power] key to turn off the mobile computer.
2) Remove the top enclosure of the mobile computer by unscrewing the four screws.
3) Insert your card properly.
14
Chapter 1
Using 9500CE Mobile Computer
4) Replace the top enclosure and tighten the screws.
Warning:
Make sure the mobile computer is set to Suspend mode; otherwise, it may
cause damage to the mobile computer. If not factory-installed, the Ingress
Protection rating of enclosures may not be the same as claimed.
Figure 7: Inserting the SD or CF Card
15
9500CE Mobile Computer Reference Manual
1.3 KEYPAD
The mobile computer is equipped with a physical keypad that consists of 27 keys. Silicon
rubber has been chosen for their durability and prompt feedback.
Figure 8: 27-key Layout
1.3.1 USING THE KEYPAD
The 27-key keypad includes alphanumeric, assorted characters, etc. This keypad is set to
numeric mode by default.
Note: Functionality of keys is application-dependent.
Press
first, and then
.
The LED backlight of keypad is turned off by default. It can be toggled ON/OFF by the
key combination: [Func] + [0].
Go to Start > Settings > Control Panel and double-tap the Keyboard icon.
The Character Repeat functionality is enabled by default. You may cancel the check
box to disable it. When enabled, tap, hold, and drag the slider for a desired Repeat
Delay and Repeat Rate.
Warning:
16
It is suggested to turn on the keypad backlight while working in a dark
area; however, using backlight while on battery power will substantially
reduce battery power.
Chapter 1
Using 9500CE Mobile Computer
1.3.2 ALPHA KEY
This alphanumeric keypad is set to numeric mode by default. The Alpha key serves as a toggle
among numeric, alpha (lower-case alphabetic), and ALPHA (upper-case alphabetic) input modes.
Note: It is not necessary to hold down the [Alpha] key.
The alpha icon will appear on the status bar in a sequence as shown below.
Status Icon
Alpha Key
Input Mode
N/A
Numbers
Small letters
Press
one time
Capital letters
Press
two times
Note: If you are using the software keypad via SIP, tap CAP (Caps Lock) to toggle
between upper case and lower case alphabetic modes.
1.3.3 FUNCTION KEY
The [Func] (= Function) key serves as a modifier key.
1) To enable this modifier key, press
on the keypad.
A circular icon of the letter "F" will appear on the status bar. This modifier key is hold
down as long as the icon is displayed.
2) Now press another key to get the value of key combination (say, press [1] to get the
value of F1). The icon will go off now.
3) To get the value of another key combination modified by the [Func] key, repeat the
above steps.
4) To abort the key modification, press
again, and the icon will go off.
Note: It is not necessary to hold down the [Func] key.
The functionality of each key combination is application-dependent. Below is a list of the
factory setting for a variety of key combinations.
17
9500CE Mobile Computer Reference Manual
Key Combination
Action
PgUp (red-coded): move text up one screenful
,
PgDn (red-coded): move text down one screenful
,
Home (red-coded): move to the beginning of screen or document
,
End (red-coded): move to the end of screen or document
,
Toggle ON/OFF the backlight of keypad only
,
Turn ON the backlight of LCD and decrease its luminosity
,
Turn ON the backlight of LCD and increase its luminosity
,
Note: Press the [Func] key first, and then press the second key for a specific function.
1.3.4 TASK KEY
By default, the [Task] key is undefined. It can be programmed as a shortcut key for a
specific program or action. Refer to Windows CE Products Programming Guide for the
supplied API – SetKeyPadBind().
18
Chapter 1
Using 9500CE Mobile Computer
1.4 TOUCH SCREEN
The mobile computer comes with a 3.5" TFT graphic LCD, 320 by 240 pixels resolution
(QVGA). The LED backlight of screen, which helps ease reading under dim environments,
can be controlled manually and automatically.
Warning:
Using backlight while on battery power will substantially reduce battery
power. It is suggested to dim the backlight while working in a well-lit area
or automatically turn off the mobile computer when not in use.
1.4.1 ADJUSTING THE BACKLIGHT
Press
first, and then
.
The LED backlight of the screen can be turned on and adjusted decreasingly by the
key combination: [Func] + [-]. Keep pressing the key combination ([Func] first, and
then [-]) until the luminosity is decreased to a desired level.
Press
first, and then
.
The LED backlight of the screen can be turned on and adjusted increasingly by the
key combination: [Func] + [.]. Keep pressing the key combination ([Func] first, and
then [.]) until the luminosity is increased to a desired level.
Go to Start > Settings > Control Panel and double-tap the Display icon.
1. Tap the Backlight tab (left below).
2. Select one or both of the check boxes to automatically turn off the LCD backlight
when using batteries or external power. From the appropriate list, select the
amount of time the device should be idle before the backlight is turned off.
3. Tap the [Advanced] button.
19
9500CE Mobile Computer Reference Manual
4. In the Settings tab (right above), you can select the luminosity of backlight when
it is set to be automatically turned on by pressing any key or tapping the screen.
Tap, hold, and drag the slider for AC and battery powered respectively. For more
luminosity, move the slider to the right.
1.4.2 RE-CALIBRATING THE SCREEN
This LCD is also a touch screen that can be calibrated through screen alignment.
Go to Start > Settings > Control Panel and double-tap the Stylus icon.
Tap the Calibration tab, and then tap the [Recalibrate] button.
Warning:
20
Do not use any pointed or sharp objects to move against the surface of the
screen.
Chapter 1
Using 9500CE Mobile Computer
1.5 NOTIFICATIONS
1.5.1 STATUS LED
The tri-color LED on top of the [SCAN] button is used to provide information on the
charging status or Bluetooth power status.
Tasks
Green LED
Red LED
Green & Red
Blue
Charging 9500CE
---
On
---
---
Charging done
On
---
---
---
Charging error
---
---
Flashing
---
Bluetooth enabled
---
---
---
On
1.5.2 AUDIO
The mobile computer is integrated with a mono speaker, which can be used for playing
sounds applied to events in Windows and programs, as well as playing audio files such
as .WAV files. In addition, it can be programmed for status feedback.
1.5.3 VIBRATOR
The mobile computer is integrated with a vibrator, which is software programmable for
feedback. This can be helpful when working in noisy environments.
21
9500CE Mobile Computer Reference Manual
1.6 DATA CAPTURE
A wide variety of scan engines is available for delivering flexibility to meet different
requirements. Depending on the scan engine integrated, the mobile computer is capable
of scanning barcodes of a number of symbologies that are enabled by default while
running ReaderConfig.exe. If you need to scan barcodes that are encoded in a different
symbology, enable the symbology first.
Appendix I - Scan Engine Settings lists the symbologies and RFID tags supported.
Appendix II - CCD/Laser Scan Engine provides information on the reader settings as
well as symbology settings for the CCD or Laser scan engine.
Appendix III - LR/ELR Laser Scan Engine provides information on the reader settings
as well as symbology settings for the (Extra) Long Range Laser scan engine.
Appendix IV - 2D Scan Engine provides information on the reader settings as well as
symbology settings for the 2D scan engine.
Note: The mobile computer allows the co-existence of one integrated scan engine and
the RFID reader.
22
Chapter 1
Using 9500CE Mobile Computer
1.7 COMMUNICATIONS
1.7.1 USING THE CRADLE
The cradle is designed for charging and communications at the same time.
1) Place the cradle on a flat and clean surface.
2) Connect the power supply cord to the power jack on the back of the cradle, and then
connect the other end of the power supply cord to a suitable power outlet. The cradle
is ready for charging the mobile computer, as well as the spare battery pack.
3) Seat the mobile computer in the cradle.
If data communications are desired at the same time, you can establish a proper
connection with a computer or remote host. For example, you may establish a USB
connection for ActiveSync.
Make sure that you have Microsoft ActiveSync installed on your computer before you
connect the USB cable from the cradle's USB device port (
) to your computer.
Refer to 2.3 Using ActiveSync.
UNDERSTANDING THE STATUS INDICATORS
Front Panel LEDs
Indication of Connection Status
Charging
Solid red
Status of Spare
Solid green
Battery
Link/TX
POWER
Charging spare battery
Charging done
Flashing (red/green)
Error occurs
Off
Battery not ready
Network Status Solid green
over Ethernet
Flashing
Ethernet connected
Transmitting / Receiving data
Cradle Power
Solid green
Power on
Off
Power off
23
9500CE Mobile Computer Reference Manual
UNDERSTANDING THE COMMUNICATION PORTS
Ports (from left to right)
Purpose
USB Device Port
This port is provided for connecting to your computer for
establishing a connection for ActiveSync.
USB Host Port
This port is provided for connecting a USB device:
Ethernet Port
Keyboard
Mouse
Card reader
Storage device, such as a memory stick
This port is provided for connecting to a legacy network. When
connected, the third LED (next to POWER) will become solid
green. During data transmission, the LED will be flashing.
1.7.2 USING WIRELESS NETWORKS
The mobile computer supports state-of-the-art wireless technologies, Bluetooth and
802.11b/g, so that it is able to send/receive data in real time in an efficient way. You
may choose to have the GPRS module embedded for a total wireless solution for data
communications.
24
Chapter 2
LEARNING WINDOWS CE BASICS
This chapter mainly describes the basic skills to work with 9500CE Mobile Computer. The
add-on utilities for applications regarding data collection, processing, and transmission,
are introduced in the following chapters.
9500CE Mobile Computer is specifically designed for real-time data collection in the
Windows CE 5.0 environment. It won't take long for any Windows user to get familiarized
with it. Keep these basic skills in mind and explore this Windows CE device at ease.
Double-tap an item to select it.
Tap and hold an item to see a menu that enables tasks, such as cut, copy, rename,
delete, etc.
Tap and drag to select multiple items.
Tap
or
application.
on the toolbar to close an active window, a dialog box, or a running
If the button is not displayed, press [ESC] on the physical keypad.
Tap
on the toolbar to save the current settings and exit the application (or
minimize the window in some applications).
If the button is not displayed, press [Enter] on the physical keypad.
IN THIS CHAPTER
2.1
2.2
2.3
2.4
2.5
2.6
Getting Started .........................................................
Finding out the Capabilities of Your Mobile Computer ......
Using ActiveSync .......................................................
Managing Programs ...................................................
System Reset & Auto Run ...........................................
Upgrading OS Image ..................................................
25
31
33
36
40
42
2.1 GETTING STARTED
When 9500CE Mobile Computer is fully charged, you may remove it from the cradle.
Then, press the [Power] key to turn on the mobile computer and wait for the Windows CE
desktop to come up. If you are using the mobile computer for the first time, there are a
couple of things to do after the desktop comes up.
To select your time zone and set the local time, go to Start > Settings > Control
Panel and select Date/Time.
To align the touch screen, go to Start > Settings > Control Panel and select
Stylus.
25
9500CE Mobile Computer Reference Manual
SUSPEND MODE
Like your PDA, Pocket PC and most handheld devices, 9500CE Mobile Computer functions
when it is turned on. This is because the Windows CE operating system eliminates the
booting process and runs continuously.
Turn On (= Resume from Suspend)
To turn on the mobile computer, simply press the [Power] key.
Turn Off (= Suspend)
To turn off the mobile computer, press the [Power] key again, or select Suspend from
the Start Menu. The system is now ready for use but not in use. This is referred to as
Suspend mode or Standby mode. It means the system is in power-saving status and
waiting for user interference.
Warning:
In order to save battery power, it is suggested that the mobile computer is
set to be automatically turned off when not in use. Refer to 1.1.4 Power
Management for more information about saving power.
2.1.1 DESKTOP
The desktop appears when the mobile computer is turned on (left below).
Tap and hold anywhere blank on the screen to manage or configure the desktop (right
below).
26
Chapter 2
Alternatively, you may tap
Learning Windows CE Basics
to the right of the taskbar, and then select Desktop.
Note: To customize the desktop, tap anywhere blank on the desktop and select
Properties.
When you turn on the mobile computer and seat it in the cradle for the first time, you will
find these icons displayed on the taskbar. Refer to 2.1.2 Taskbar for more information on
the icons.
Icon
Description
See Also
This icon shows the amount of battery charge remaining in the main
battery. The more bars, the more power in the main battery.
1.1.3 Understanding
the Battery Icons
This icon shows that the main battery is ready for charging. For
information on charging status, refer to the LEDs on the mobile
computer as well as on the cradle.
1.1.3 Understanding
the Battery Icons
This icon shows that numeric mode is in use for data input via
keypad.
1.3.2 Alpha Key
This icon shows that your cradle is directly connected to a computer
via USB port.
1.7.1 Using the
Cradle
Make sure you have Microsoft ActiveSync installed on your 2.3 Using
computer.
ActiveSync
There may be two of this icon, one is for BTPAN1 disabled, the 3.2 Changing
Connection Settings
other for AX88772 (Ethernet) disabled.
This icon is a shortcut to the Wireless Power Manager that controls
the power to GPRS and 802.11b/g modules.
4.1 Wireless Power
Manager
2.1.2 TASKBAR
The taskbar is at the bottom of the screen for displaying the Start button, status icons
for various connections or programs, SIP button, Switch Task button, etc.
Note: To configure different connections, go to Start > Settings and select Network
and Dial-up Connections.
27
9500CE Mobile Computer Reference Manual
UNDERSTANDING THE ICONS ON THE TASKBAR
Icon
Description
See Also
Tap it to switch to desktop or any task, such as a running program or Switch Task
window.
Tap it to change the input method.
Software Input
Panel (SIP)
It indicates the amount of battery charge remaining in the main
battery. The more bars, the more power in the main battery.
1.1.3 Understanding
the Battery icons
It indicates the battery status. Other status icons are
1.1.3 Understanding
the Battery icons
.
It indicates the current input mode of keypad. The other icons are
1.3.2 Alpha Key
.
It indicates the modifier key is enabled. (= Function mode)
1.3.3 Function Key
The USB connection for ActiveSync operation is successfully
established.
3.2.1 USB
Connection (via
cradle)
Double-tap it to view status. Tap [Disconnect] if necessary.
The Bluetooth PAN connection fails. (= disconnected)
3.2.5 BTPAN
The Bluetooth PAN connection is successfully established through the
Bluetooth Manager utility.
Double-tap it to view or renew IP Information.
The Ethernet connection via AX88772 fails. (= disconnected)
3.2.3 Ethernet (via
cradle)
The Ethernet connection via AX88772 is successfully established once
the Cat. 5 cable is connected.
Double-tap it to view or renew IP Information.
It provides control of the power to the 802.11b/g and GPRS modules. 4.1 Wireless Power
Manager
Double-tap any of these icons to configure the power setting.
It indicates the GPRS module is enabled.
See GPRS status icon
below.
It indicates a CF card other than GPRS is enabled.
It indicates the Wi-Fi module (802.11b/g) is enabled. The more green
bars, the stronger the signal.
See WLAN1 status icons
28
below.
Chapter 2
Learning Windows CE Basics
The GPRS connection has been opened. If it fails, the icon will be
gone. If the icon persists, it means the GPRS connection is
successfully established.
3.2.2 GPRS
Double-tap it to view status. Tap [Disconnect] if necessary.
The Wi-Fi connection fails. (= disconnected)
Double-tap it to access the
establishing a new connection.
Wireless
3.2.4 WLAN
Information
tab
for
The Wi-Fi connection is successfully established.
Double-tap it to view or renew IP & Wireless Information.
It provides access to the Bluetooth services.
Initially, you need to go to Start > Programs > BTManager to
open the Bluetooth Manager so that this icon will appear on the
taskbar.
4.2 Bluetooth
Manager
It provides access to the Reader Configuration Utility.
Initially, you need to double-tap the ReaderConfig shortcut on the
desktop so that this icon will appear on the taskbar.
Note: In OS version 1.1 and later, it can display up to 5 status icons for U.S. and
European languages and up to 4 status icons for Asian languages.
2.1.3 START MENU
Tap the Start button on the taskbar to open the Start Menu.
Options
Description
Programs
Provides access to available programs in the directory: \Windows\Programs
Favorites
Provides access to your favorites in the directory: \Windows\Favorites
Documents
Provides access to recent opened documents in the directory:
\Windows\Recent
Settings
Provides access to
Control Panel
Network and Dial-up Connections
Taskbar and Start Menu
29
9500CE Mobile Computer Reference Manual
Run...
Opens a program or folder or document.
Suspend
Enters the Suspend mode.
Note: To configure the Start menu and taskbar, go to Start > Settings and select
Taskbar and Start Menu.
2.1.4 INPUT METHODS
Data entry can be performed by the following methods:
Type with the physical keypad.
Scan barcode or RFID tag in applications, e.g. WordPad, CipherLab's Application
Generator, etc.
Tap or write using SIP (Soft Input Panel)
USING THE SOFT INPUT PANEL (SIP)
Tap the SIP button on the taskbar to select a SIP mode or hide the input panel.
In each mode, the characters appear as typed text on the screen.
Options
Description
Keyboard
To type using the virtual keyboard.
Transcriber
To write freely on the screen in applications, such as WordPad, Inbox, etc.
30
Chapter 2
Learning Windows CE Basics
2.2 FINDING OUT THE CAPABILITIES OF YOUR MOBILE COMPUTER
2.2.1 CHANGING DEVICE NAME
1) Go to Start > Settings > Control Panel and select System to obtain essential
system information.
2) Select the Device Name tab to change the identification for the mobile computer.
2.2.2 UNDERSTANDING DEVICE CONFIGURATION
The device configuration of 9500CE Mobile Computer is displayed in 5 digits: xxxx-x
Take the screenshot of System Properties below for example. Its device configuration is
“5410-0”, which means the 27-key mobile computer has equipped with the following
parts –
A scan engine that employs extra long range laser
Integrated Bluetooth and Wi-Fi modules
An RFID reader
Device Code
Modular Component
Types
1st digit
Reader module
0= none
1= CCD scan engine
2= Laser scan engine
3= 2D scan engine
4= Long Range Laser scan engine
5= Extra Long Range Laser scan engine
31
9500CE Mobile Computer Reference Manual
2nd digit
Wireless module
3= Bluetooth + GPRS
4= Bluetooth + 802.11b/g
5= Bluetooth only
7= Bluetooth + GPRS + 802.11b/g
3rd digit
RFID module
0= none
1= RFID reader
4th digit
Reserved
(Hardware version)
5th digit
Keypad module
0= 27-key
32
Chapter 2
Learning Windows CE Basics
2.3 USING ACTIVESYNC
ActiveSync is used to synchronize information between 9500CE Mobile Computer and
your desktop computer, to install programs on the mobile computer, and to backup and
restore the mobile computer.
The Microsoft ActiveSync program has to be installed on your desktop computer first.
To download the up-to-date version of the program, you may need to go to
Microsoft's official web site for Windows Mobile devices as shown below.
http://www.microsoft.com/windowsmobile/default.mspx
http://www.microsoft.com/windowsmobile/activesync/activesync45.msp
x
After downloading and installation, run the program. For detailed information on the
program, you may click the Help menu, and then select the Microsoft ActiveSync
Help.
2.3.1 SYNCHRONIZATION WITH YOUR COMPUTER
1) Follow these instructions for initial ActiveSync operation:
Connect the USB cable from the cradle's USB device port (
) to your computer.
Connect the power cable from the cradle to a nearby power outlet.
Turn on the mobile computer and seat it in the cradle.
2) Your computer will automatically detect the USB device. Click [OK] when the
connection is established.
3) Select which partnership to set up. If you want to synchronize data between the
mobile computer and your personal computer, select Standard Partnership; otherwise,
select Guest Partnership.
4) Wait a few seconds for the mobile computer to get connected (and synchronized if a
Standard Partnership is selected).
Note: (1) For ActiveSync via Bluetooth, refer to 4.2 Bluetooth Manager.
(2) We recommend that you have ActiveSync 3.7.1 installed on your computer
because ActiveSync 4.x does not officially support Windows CE 5.0 devices.
2.3.2 ADD/REMOVE PROGRAMS
Click [Add/Remove Programs] from the Tools Menu so that you can proceed to install a
program that is designed to be used on a mobile device running Windows CE.
If a user program is no longer desired, you may remove it from the system. Click
[Add/Remove Programs] from the Tools Menu so that you can proceed to un-install a
program that is designed to be used on a mobile device running Windows CE.
33
9500CE Mobile Computer Reference Manual
ALTERNATIVE TO INSTALL NEW PROGRAMS (COPY & PASTE)
Alternatively, you may install a new program manually.
1) When connected, open the Microsoft ActiveSync window on your desktop computer.
2) Click the Explorer button from the toolbar.
3) Navigate to the target folder, e.g. the Programs folder (\Windows\Programs),
depending on where you wish to access the program.
4) Navigate through file folders on your computer to find the new program (.CAB, .EXE,
etc.)
5) Right-click the program and select [copy] from the pop-up menu.
6) Back to the target folder in step 3.
Right-click anywhere blank and select [Paste] from the pop-up menu.
7) On the mobile computer, go to Start > Programs and the new program will appear.
ALTERNATIVE TO REMOVE PROGRAMS (CONTROL PANEL)
Alternatively, you may un-install a new program manually.
1) Go to Start > Settings > Control Panel and select Remove Programs.
2) Tap the name of the program that you want to delete.
3) Tap [Remove].
4) Tap [Yes] to un-install the program.
Note: If the program does not appear in the list of installed programs, you may use
Windows Explorer to locate it. Tap and hold the program to select [Delete] from
the pop-up menu.
2.3.3 BACKUP/RESTORE
To best protect your work, you should regularly back up information on your mobile
computer.
34
Chapter 2
Learning Windows CE Basics
You can perform a backup by during the ActiveSync operation. The backup file is stored
on your desktop computer.
Note: The CipherLab Backup Utility is provided in OS 1.20.0409.070524 or later
versions.
35
9500CE Mobile Computer Reference Manual
2.4 MANAGING PROGRAMS
2.4.1 QUICK LAUNCH A PROGRAM
Tap the Start button to view the Start Menu. To quick launch a program, tap it from the
Programs folder.
Note: Alternatively, you may tap Start and select Run to run a specific program or open
a document.
If you wish to quick launch a new program, add it to the Programs folder: My
Device\Windows\Programs. The program will become available in the Start Menu.
To add a new program or subfolder to the Programs folder, you can either use Windows
Explorer or ActiveSync.
Windows Explorer: to move the program by [Copy] and [Paste Shortcut].
ActiveSync on the desktop computer: to create a shortcut to the program, and place
the shortcut in the Programs folder.
Warning:
To avoid making any changes to the program configurations by accident,
we recommend you to use [Copy] and [Paste Shortcut] rather than [Cut]
and [Paste].
USING WINDOWS EXPLORER TO ADD A PROGRAM TO START MENU
1) Go to Start > Programs and select Windows Explorer. Alternatively, you can
press the [Task] key on the keypad to launch Windows Explorer.
2) Navigate through file folders to find the program you desire.
3) Tap and hold the program to select [Copy] from the pop-up menu.
36
Chapter 2
Learning Windows CE Basics
4) Navigate to the Programs folder (My Device\Windows\Programs).
5) Tap and hold anywhere blank on the screen to select [Paste Shortcut] from the
pop-up menu. The new program will be added to the Programs folder.
6) Go to Start > Programs and the new program will appear now.
USING ACTIVESYNC TO ADD A PROGRAM TO START MENU
1) When connected, open the Microsoft ActiveSync window on your desktop computer.
2) Click the Explorer button from the toolbar.
37
9500CE Mobile Computer Reference Manual
3) Navigate through file folders to find the program you desire.
4) Right-click the program and select [Create Shortcut] from the pop-up menu.
5) Right-click the shortcut and select [Cut] from the pop-up menu.
6) Navigate to the Programs folder (Mobile Device\Windows\Programs).
7) Right-click anywhere blank on the window and select [Paste] from the pop-up menu.
The new program will be added to the Programs folder.
8) On the mobile computer, go to Start > Programs and the new program will appear
now.
Note: [Create Shortcut], [Cut], and [Paste]: The same result can be performed by [Copy]
and [Paste Shortcut].
2.4.2 CREATE A FOLDER
USING WINDOWS EXPLORER TO ADD A NEW FOLDER
1) Go to Start > Programs and select Windows Explorer.
Alternatively, you can press the [Task] key on the keypad to launch Windows
Explorer.
2) Navigate through file folders to find where you wish to create a new folder.
3) Tap and hold anywhere blank on the window and select [New Folder] from the pop-up
menu. A subfolder will be created.
USING ACTIVESYNC TO ADD A NEW FOLDER
1) When connected, open the Microsoft ActiveSync window on your desktop computer.
2) Click the Explorer button from the toolbar.
3) Navigate to the target folder where you wish to create a new folder.
38
Chapter 2
Learning Windows CE Basics
4) Right-click anywhere blank on the window and select [New Folder] from the pop-up
menu. A subfolder will be created.
2.4.3 SWITCH AMONG PROGRAMS AND DESKTOP
Tap
to the right of the taskbar and select a running program.
2.4.4 EXIT A PROGRAM
In general, the system manages memory automatically, and there is no need to exit a
program in order to open another or to conserve memory. However, random access
memory (SDRAM) may be used up when running too many programs. As a result, it will
slow down the operation or cause program errors. In that case, you should stop one or
more running programs to free memory. In order to use memory in a more efficient way,
you are recommended to exit a program when it is not desired any longer.
Warning:
Always remember to save data or settings before you exit a program.
Tap
or
to close an active window, a dialog box, or a running application. If the
button is not displayed on the toolbar, press [ESC] on the physical keypad.
to save the current settings and exit the application (or minimize the window in
Tap
some applications). If the button is not displayed on the toolbar, press [Enter] on the
physical keypad.
Note: Some programs, such as the Reader Configuration Utility (ReaderConfig.exe), may
create an associated icon on the taskbar. You may tap the icon and select [Exit]
from the pop-up menu.
39
9500CE Mobile Computer Reference Manual
2.5 SYSTEM RESET & AUTO RUN
Reset the mobile computer when it stops responding to input.
Software Reset: Simply press the [Reset] button.
Hardware Reset: Press the [Reset] button and the [Power] key at the same time.
Warning:
Never perform hardware reset unless software reset cannot solve your
problems.
2.5.1 SOFTWARE RESET (WARM REBOOT)
Software reset, also known as a warm boot, will restart the mobile computer and keep all
the saved files. To perform software reset, use the stylus to press the [Reset] button.
During operation, the removal of main battery will start software reset too.
Warning:
Data loss may occur when files are not properly closed before software
reset.
2.5.2 HARDWARE RESET (COLD REBOOT)
Hardware reset, also known as a cold boot, will restart the mobile computer too.
However, it performs a full restore of the mobile computer to its factory settings and
initializes SDRAM. To perform hardware reset, press the [Power] key and [Reset] button
at the same time.
Data and program files stored in SDRAM will be erased after hardware reset. But you can
restore data that is previously synchronized with your computer by performing an
ActiveSync operation, or backed up by using CipherLab Backup Utility.
Warning:
Only the files stored in the Flash File System are retained during hardware
reset.
2.5.3 AUTO RUN
Auto Run is supported in OS 1.20.0409.070524 or later versions.
To find out your OS version, go to Start > Settings > Control Panel and select
System. Select the Device Name tab.
40
Chapter 2
Learning Windows CE Basics
Upon hardware or software reset, the OS shall automatically execute AutoRun.exe
and/or AutoRun.ini if any of the two files can be found in the “\DiskOnChip” folder or on
SD card.
If AutoRun.exe exists
Upon cold boot, the OS shall automatically execute AutoRun.exe
Upon warm boot, the OS shall automatically execute AutoRun.exe
If AutoRun.ini exists
Upon cold boot, the OS shall automatically check the contents of AutoRun.ini and execute
them (if there is any).
Any line prefixed with a semicolon “;” is supposed to be a comment line only; otherwise it is
an executable file or command and shall be executed (line by line). For example,
\DiskOnChip\cerdisp.exe
:\DiskOnChip\ReaderConfig.exe
;\DiskOnChip\RF9500_CE.exe
..\DiskOnChip\cerdisp.cab
:..\DiskOnChip\ReaderConfig.cab
The line to execute a cabinet file (.cab) must be specified with two dots “. .” for the absolute
path.
Upon warm boot, the OS shall automatically check the contents of AutoRun.ini and execute
any line that is prefixed with a colon “:”.
Any line prefixed with a semicolon “;” is supposed to be a comment line only. For example,
:\DiskOnChip\ReaderConfig.exe
;\DiskOnChip\RF9500_CE.exe
:..\DiskOnChip\ReaderConfig.cab
The line to execute a cabinet file (.cab) must be specified with a colon “:”, followed by two
dots “. .” for the absolute path
Note: Because the cabinet files are designed to install the application, tidy up, and then
“self destruct”, they will be automatically deleted from your mobile computer after
installation. However, AutoRun.ini will backup the original files (.cab) while
installing cabinet files, and restore them after installation. Consequently, these
cabinet files will be automatically re-installed to your mobile computer upon cold
boot or warm boot, if specified in AutoRun.ini.
41
9500CE Mobile Computer Reference Manual
2.6 UPGRADING OS IMAGE
To upgrade the OS image on your mobile computer, run the program "DLDR.exe" on the
desktop of your computer.
Warning:
The OS upgrade should be performed with great caution because
everything on the mobile computer will be erased. Backup user-installed
applications and files to your computer first only. Please contact your sales
representative for the OS upgrade utility "DLDR.exe".
1) Install Microsoft ActiveSync on your computer. For initial ActiveSync operation, refer
to 2.3 Using ActiveSync for details.
Now, disable the ActiveSync operation as shown below.
2) Run DLDR.exe on your computer.
3) Press [Reset] + [Power] to perform hardware reset on 9500CE.
4) Press [Space] + [8] + [Power] simultaneously in three seconds so that 9500CE can
enter the "Download" mode.
5) Seat 9500CE in the cradle.
6) Press [Enter] on 9500CE to start upgrading image.
It will take approximately 5 minutes before a message is displayed on the mobile
computer to indicate the OS upgrade is completed successfully.
7) Wait a few seconds for software reset will be performed automatically.
8) Press [Reset] + [Power] to perform hardware reset on 9500CE again.
Warning:
42
Do not press any key on the mobile computer while upgrading OS image.
Upon completion, you cannot reload any older image.
Chapter 3
PERSONALIZING 9500CE MOBILE COMPUTER
In this chapter, a brief on the system settings is provided for your reference.
Note: User settings are stored in SDRAM and will be overwritten by the system defaults
after hardware reset. However, you can use the CipherLab Backup Utility to
backup the current registry for restore purpose.
IN THIS CHAPTER
3.1 Changing System Settings .......................................... 43
3.2 Changing Connection Settings ..................................... 47
3.1 CHANGING SYSTEM SETTINGS
Go to Start > Settings > Control Panel.
Items
Description
In the [Accessibility] dialog box, you may use these options to customize the way an
external keyboard, display, or mouse functions. Many of these features are useful to
people without disabilities.
Keyboard tab: Select StickyKeys to enable simultaneous keystrokes while
pressing one key at a time; select ToggleKeys to emit sounds when certain
locking keys are pressed.
Sound tab: Select SoundSentry to provide visual warnings for system sounds.
43
9500CE Mobile Computer Reference Manual
Keyboard tab: Select StickyKeys to enable simultaneous keystrokes while
pressing one key at a time; select ToggleKeys to emit sounds when certain
locking keys are pressed.
Sound tab: Select SoundSentry to provide visual warnings for system sounds.
Mouse tab: Select MouseKeys to enable the keyboard to perform mouse functions
Display tab: Select High Contrast to improve screen contrast with alternative
colors.
General tab: Select Automatic Reset if you wish to turn off accessibility features
after a specific period of time; select Notification if you wish to hear a sound
when turning a feature on or off.
In the [Certificates] dialog box, you may view or modify digital certificates that some
application use to establish trust for secure connections.
In the [Date/Time] dialog box, you may change date, time, and time zone settings.
In the [Dialing Properties] dialog box, you may configure settings for modem
communications, such as the GPRS modem.
In the [Display Properties] dialog box,
Background tab: Select an image for the background.
Backlight tab: Specify for how long the mobile computer is idle and then the
backlight will be automatically turned off while on battery power and external
power (in the charging cradle) respectively. Tap the [Advanced] button to move
the slider and adjust the brightness of the LCD backlight when it is set to be
automatically turned on once a key is pressed or you tap the touch screen.
Appearance tab: Select a desired color scheme for windows, dialog boxes, and
items.
In the [Input Panel Properties] dialog box, you may configure how the Soft Input
Panel (SIP) works.
In the [Internet Options] dialog box, you may configure how the mobile computer
connects to the Internet.
Connect an external keyboard to the cradle via the USB Host port.
In the [Keyboard Properties] dialog box, you may configure settings for character
repeat.
Connect a mouse to the cradle via the USB Host port.
In the [Mouse Properties] dialog box, you may configure and test your double-click
settings.
44
Chapter 3
Personalizing 9500CE Mobile Computer
In the [Network and Dial-up Connections] window, you may configure settings for
the mobile computer connects to a network directly or through a modem.
Alternatively, you may tap Start > Settings > Network and Dial-up Connections.
USB Connection (via USB device port on the cradle)
GPRS (through a GPRS modem)
AX88772 (via Ethernet port on the cradle)
WLAN (via 802.11b/g)
BTPAN (via Bluetooth)
In the [Owner Properties] dialog box,
Identification/Notes tab: Type your contact information or notes.
Network ID tab: Type the user name, password, and domain name used to log
on to the remote network.
In the [Password Properties] dialog box, you may apply password protection to limit
access to the mobile computer.
In the [PC Connection Properties] dialog box, you may disable the direct connection
between the mobile computer and a desktop computer.
By default, the mobile computer is enabled to directly connect to a desktop
computer via the cradle's USB port. Alternatively, you may tap Start > Settings
> Network and Dial-up Connections and select USB Connection.
You may change to use Bluetooth if ActiveSync via Bluetooth has been enabled in
the Bluetooth Manager
In the [Power Properties] dialog box,
Battery tab: You may view the current status of main and backup batteries.
Schemes tab: You may configure the power scheme and switching.
Device Status tab: You may view the devices that are consuming power.
In the [Regional and Language Settings] dialog box,
Region tab: You may customize the appearance and formatting to your
geographic region.
Language tab: By default, it is set to English (United States).
Input tab: By default, it is set to English (United States)-US.
In the [Remove Programs] dialog box, you may remove any program that is installed
earlier.
In the [Storage Properties] dialog box,
Storage Manager tab: You may reformat the available storage device, either the
DiskOnChip folder or storage card. Actions include "Dismount the storage
device", "Format the storage device", and "Set up disk partitions". The Storage
Manager is for the use of system administrators only.
In the [Stylus Properties] dialog box,
Double-Tap tab: You may configure and test your double-tap settings.
Calibration tab: You may need to re-calibrate the touch screen if it is not
responding properly to your taps.
45
9500CE Mobile Computer Reference Manual
In the [System Properties] dialog box,
General tab: You may view the system information.
Copyrights tab: You may view the important statements on copyrights.
Memory tab: You may move the slider and adjust the SDRAM allocation.
Device Name tab: You may type a name and description for identifying the
mobile computer.
Client access licenses (CALs) issued by the Terminal Server license server allow
clients to connect to the terminal server.
Use Remote Desktop Connection to log onto a Windows Terminal Server or a
computer remotely. You may access all of the programs, files, and network resources
on the remote host or terminal server.
In the [Volume & Sounds Properties] dialog box,
46
Volume tab: You may move the slider and adjust the volume and select to play
sounds for Events, Applications or Notifications.
Sounds tab: You may configure sounds for different Windows events.
Chapter 3
Personalizing 9500CE Mobile Computer
3.2 CHANGING CONNECTION SETTINGS
Go to Start > Settings > Control Panel and select Network and Dial-up
Connections. Alternatively, you may go to Start > Settings > Network and Dial-up
Connections.
Connections
Description
See Also
This is a shortcut to USB Connection, and the
selected interface is USB for factory setting. This
connection is reflected in the control panel for
direct PC connection.
Start > Settings > Control
Panel >
/
This is a shortcut to GPRS connection. Note that
the power to the GPRS module must be turned on
through the Wireless Power Manager for
establishing a connection.
This is the control of Ethernet module AX88772. It
is enabled automatically when the mobile computer
is seated in the cradle.
This is the control of 802.11b/g module for wireless
local area networking (WLAN) connection, which is
disabled by default.
This is the control of Bluetooth module for wireless
personal area networking (WPAN) connection,
which is not available until the Bluetooth
Manager is executed.
47
9500CE Mobile Computer Reference Manual
Toolbar Items
Description
Remarks
Tap this button to open the Connection menu. The
available options depend on the connection you
select.
Tap and hold the icon of a
desired connection type.
Then, select an option from
its associated menu.
Tap this button to toggle on/off the connection you
select. The toggle is used for Enable/Disable or
Connect/Disconnect.
Tap this button to delete the connection you select.
Tap this button to view the properties of the
connection you select.
48
Chapter 3
Personalizing 9500CE Mobile Computer
3.2.1 USB CONNECTION
The USB connection is specifically for performing the ActiveSync operation via the cradle.
Generally, it will automatically establish the connection and start the ActiveSync
operation when you seat the mobile computer in the cradle. To stop the ActiveSync
operation, simply remove the mobile computer.
Tap and hold "USB Connection". The pop-up menu provides a number of options.
Note: Please ignore [Properties] as the associated settings will not take effect.
STATUS - DISCONNECT
If you want to stop the ActiveSync operation without removing the mobile computer from
the cradle, select [Status] and tap [Disconnect]. Alternatively, you may double-tap
from the taskbar and tap [Disconnect].
When connected, the status icon
will appear on the taskbar.
When disconnected, this icon will disappear.
49
9500CE Mobile Computer Reference Manual
3.2.2 GPRS
Tap and hold "GPRS". The pop-up menu provides a number of options.
CONNECT/DISCONNECT
1) Turn on the power to the GPRS module through the Wireless Power Manager. Its
associated icon
on the taskbar will become
.
2) If the default PIN code does not match the one of your SIM card, the SIM PIN CODE
dialog box (right above) will appear to request the correct PIN code.
50
Chapter 3
Personalizing 9500CE Mobile Computer
You will have two chances to enter the correct PIN code.
Note: The PIN verification on the mobile computer only allows two attempts because the
system will always process the default number first ("1234" for factory setting).
Unless it matches the PIN code of your SIM card, you will have to manually input
the correct PIN code. If you succeed, the PIN code you input will overwrite the
factory setting and become the default PIN code. If you fail two times, the PIN will
be blocked.
3) Go to Start > Settings > Network and Dial-up Connections. Tap and hold
"GPRS" to select [Connect] from the pop-up menu. If your dial-up configuration is
correct, simply tap the [Connect] button in the Dial-Up Connection dialog box.
If you need to configure the dial-up settings, tap the [Dial Properties] button.
Alternatively, you may go to Start > Settings > Control Panel and select Dialing.
51
9500CE Mobile Computer Reference Manual
4) After you tap the [Connect] button, the GPRS status will go through opening port,
user authenticated, device connected until it is connected finally.
will appear on the taskbar to indicate the GPRS connection is
The status icon
established successfully. If you want to disconnect, double-tap the icon and tap the
[Disconnect] button.
GPRS PROPERTIES
When selected, you can configure the GPRS properties. Once the SIM card is inserted,
the default GPRS modem will appear as shown below. Tap [Configure].
Select the Call Options tab. The special modem commands inserted into the dial string
must be [+cgdcont=1,,"AP name"]. For example, change "internet" below to the name of
your GPRS AP.
52
Chapter 3
Personalizing 9500CE Mobile Computer
3.2.3 ETHERNET (LAN CARD AX88772)
Tap and hold "AX887721". The pop-up menu provides a number of options.
ENABLE/DISABLE
Icons
Description
By default, Ethernet is enabled when the mobile computer is seated in the cradle.
When a Cat. 5 cable is connected, the status icon
will become
.
The "Link/Data" LED on the cradle will indicate the network status.
Tap and hold "AX887721" to select [Disable] from the pop-up menu. The status
icon will disappear.
Note: By default, DHCP is enabled. Instead of using DHCP, select [Properties] and
specify a static IP address to the mobile computer. Only change these settings
according to your network administrator's instructions.
53
9500CE Mobile Computer Reference Manual
3.2.4 WLAN
Tap and hold "WLAN1". The pop-up menu provides a number of options.
CONNECT/DISCONNECT
Turn on the power to the 802.11b/g module through the Wireless Power Manager.
Wait a few seconds for the mobile computer to automatically connect to the preferred
network you have configured.
Icons
Description
By default, the 802.11b/g module is disabled. No status icon.
Enable the 802.11b/g module through the Wireless Power Manager. The icon
on the taskbar will become
, and the network status icon
will appear.
When successfully connecting to an access point or other Wi-Fi enabled device, the
icon
will become
icon
will become
54
indicating the signal strength, and the network status
.
A strong signal (five bars) usually means that the wireless network is close or
there is no interference. For best performance, connect to the wireless network
with the strongest signal. However, if an unsecured network has a stronger
signal than a security-enabled one, it's safer for your data if you connect to the
security-enabled network (but you must be an authorized user of that
network).
Chapter 3
Personalizing 9500CE Mobile Computer
To improve the signal strength, you can move your mobile computer closer to
the wireless router or access point, or move the router or access point so it’s
not close to sources of interference such as brick walls or walls that contain
metal support beams.
Note: By default, DHCP is enabled. Instead of using DHCP, select [Properties] and
specify a static IP address to the mobile computer. Only change these settings
according to your network administrator's instructions.
INITIAL CONNECTION
1) For initial connection, turn on the power to the 802.11b/g module through the
Wireless Power Manager first.
2) Double-tap
on the taskbar.
3) Select an available network and tap [Connect]. (right above)
Otherwise, you may double-tap [Add New...] and add a new network option. (left
below)
For more network settings, tap [Advanced] on the Wireless Information tab.
If you need to change the network settings, double-tap the selected network, and
the Wireless Properties dialog box appears for configuration. (right below)
55
9500CE Mobile Computer Reference Manual
RSSI TRIGGER
RSSI stands for Received Signal Strength Indication. Use an RSSI value to determine
when it comes below a certain threshold at which point the mobile computer will
seamlessly switch the network connection, for example, while moving in and out of range
between different access points. Select [Adaptive Connection] and pick up a suitable
value.
Cancel the selection of [Adaptive Connection] when you are using a third-party
application capable of configuring the switching itself in order to maintain a constant
connection to the network.
56
Chapter 3
Personalizing 9500CE Mobile Computer
3.2.5 BTPAN
Tap and hold "BTPAN1". The pop-up menu provides a number of options.
ENABLE/DISABLE
Icons
Description
This is the control of Bluetooth module for wireless personal area networking
(WPAN) connection, which is not available until the Bluetooth Manager is executed.
When enabled, the status icon
will become
.
Tap and hold "BTPAN1" to select [Disable] from the pop-up menu. The status icon
will disappear.
Note: By default, DHCP is enabled. Instead of using DHCP, select [Properties] and
specify a static IP address to the mobile computer. Only change these settings
according to your network administrator's instructions.
57
9500CE Mobile Computer Reference Manual
58
Chapter 4
USING APPLICATIONS
9500CE Mobile Computer provides several utilities and key applications which are made
accessible from the desktop or the taskbar.
Wireless Power Manager lets you determine whether the power is supplied to the
GPRS or WLAN module, along with its associated driver installed.
Bluetooth Manager lets you configure the Bluetooth settings and use the Bluetooth
services provided on the remote devices.
ReaderConfig lets you manage the barcode or RFID reader.
Inbox lets you send and receive e-mail by connecting to a POP3 or IMAP4 server.
Backup Utility lets you manipulate the way to backup programs and data.
In this chapter, a brief on the system settings is provided for your reference.
Note: User settings are stored in SDRAM and will be overwritten by the system defaults
after hardware reset. However, you can use the CipherLab Backup Utility to
backup the current registry for restore purpose.
IN THIS CHAPTER
4.1
4.2
4.3
4.4
4.5
Wireless Power Manager .............................................
Bluetooth Manager.....................................................
Reader Configuration Utility.........................................
Inbox .......................................................................
Backup Utility............................................................
60
61
72
77
80
59
9500CE Mobile Computer Reference Manual
4.1 WIRELESS POWER MANAGER
Wireless Power Manager is a control panel applet, which allows you to choose and
enable 802.11b/g, GPRS or other CF card.
Note: Meanwhile, you may enable Bluetooth connectivity through the Bluetooth
Manager.
1) Double-tap the associated icon
on the taskbar to run Wireless Power Manager.
2) Select the wireless connectivity you desire, and then tap
.
It takes several seconds to turn on the power to the wireless module and install the
driver. When both GPRS and 802.11b/g are enabled on battery power, the main
battery charge will drop down substantially.
Double-tap any of the following icons to access power management.
The icon indicates that GPRS power (CF card type) is turned on.
This icon indicates that other CF card is present instead of GPRS.
The icon indicates that 802.11b/g power is turned on, and the green bars indicate
the wireless signal strength. The more the bars, the stronger the signal.
Note: You may need to turn off the wireless power or simply stop the wireless signals at
times, in order to conserve battery power, or in situations where the use of radio
is prohibited, such as on airplanes, in hospitals, etc.
60
Chapter 4
Using Applications
4.2 BLUETOOTH MANAGER
Bluetooth Manager is a utility that helps you access and manage the available
Bluetooth services.
4.2.1 BLUETOOTH PROFILES SUPPORTED
The supported Bluetooth profiles are:
Serial Port Profile
(SPP)
Object Push Profile
(OPP)
File Transfer Profile
(FTP)
Dial-Up Networking Profile
(DUN)
Synchronization Profile
(SP)
PAN Service Profile
(PAN)
Human Interface Device Profile (HID)
4.2.2 BLUETOOTH TOOLBAR
Buttons
Description
See Also
Tap this button to view shortcuts to preferred Bluetooth services, which may
be provided on different Bluetooth devices. Then tap a desired Bluetooth
service to establish a quick link.
You will have to make a connection and created a shortcut to a specific
Bluetooth service first.
Tap this button to view the Bluetooth devices discovered during this session.
If you tap the button for the first time, it will start the inquiry process to
discover nearby Bluetooth devices.
Tap this button to view the Bluetooth services provided.
By default, these services are all available, and therefore, displayed
along with a plug icon "
".
To view properties of a service, tap and hold it to select [Properties]
from the pop-up menu.
To disable a service, tap and hold it to select [Stop].
61
9500CE Mobile Computer Reference Manual
Serial Port
Properties
If "Auto Server COM Port" is enabled, the COM port providing Serial Port
service will be assigned automatically (COM6 by default).
If "Auto Server COM Port" is disabled, you can select a COM port by
following these steps:
File
Transfer
Properties
You can change the FTP folder.
By default, uploading files to the mobile computer is allowed. You can
cancel the check box to prohibit uploading.
Object Push You can change the Bluetooth exchange folder.
Properties
62
Chapter 4
Using Applications
Tap this button to view Bluetooth properties.
General tab It displays device name, MAC address, as well as the device type.
If you wish to change the device name of the mobile computer, go to Start
> Settings > Control Panel and select System.
Security
tab
Authentication Setting: It is disabled by default. When enabled, PIN code
is required.
Discoverability: It is set discoverable by default. If you do not wish to
provide Bluetooth services to other remote devices, cancel the check
box.
Default PIN: It is disabled by default. You may set a link key to skip the
PIN code input.
63
9500CE Mobile Computer Reference Manual
Options tab
Start minimized: When selected, once you run the Bluetooth Manager
program, its window will be minimized to an icon
on the taskbar.
Only when you tap the icon, will it open the Bluetooth Manager window.
Refer to the "Minimized" button below.
Auto Client COM Port: When enabled, the default COM port for remote
Serial Port service will be assigned automatically. When disabled, you
can select a COM port.
Auto Server COM Port: When enabled, the COM port for local Serial Port
service will be assigned automatically (COM6 by default).
Tap this button and tap [Connect via Cradle] to stop ActiveSync via
Bluetooth.
Tap this button to minimize the Bluetooth Manager window.
Tap this button to stop inquiring.
Tap this button to refresh the device list.
When using the File Transfer service on a remote device, you can tap this
button to move up one level if a subfolder exists.
Tap this button to view the Bluetooth profiles supported -
SPP for Serial Port Profile
OPP for Object Push Profile
FTP for File Transfer Profile
DUN for Dial-Up Networking Profile (supports Client only)
Note that the mobile computer also supports the following profiles -
64
PAN Service Profile
Human Interface Device (HID) Profile
Chapter 4
Using Applications
4.2.3 STARTING BLUETOOTH SERVICES
1) Go to Start > Programs > BTManager to open the Bluetooth Manager.
2) It takes several seconds to enable the Bluetooth services. The associated icon
will
appear on the taskbar. Meanwhile, the LED on the mobile computer will turn blue.
STOPPING BLUETOOTH SERVICES
You may need to stop using the Bluetooth services, in order to conserve battery power,
or in situations where the use of radio is prohibited, such as on airplanes, in hospitals,
etc.
Tap
and select [Exit] from the drop-down menu, as shown right
above, to stop all Bluetooth connections and exit the application. The LED on the
mobile computer will go off.
When the Bluetooth window is minimized, tap
window.
on the taskbar to maximize the
4.2.4 DISCOVERING BLUETOOTH DEVICES
1) Tap
to discover nearby Bluetooth devices (left below).
2) Wait for a few seconds, and it will list the discovered devices (right below).
65
9500CE Mobile Computer Reference Manual
4.2.5 PAIRING
When authentication is enabled on the target device, you will have to pair with it before
starting a connection.
1) From the device list, tap and hold the desired device to select [Pair] from the pop-up
menu. (left below)
2) Enter the PIN code that is specified on the remote device. (right above)
66
Chapter 4
Using Applications
3) Once paired successfully, the paired device will be displayed along with a lock icon
" ".
UNPAIR DEVICES
To unpair with a device from the device list, you will have to tap and hold the desired
device to select [Unpair] from the pop-up menu.
Note: The mobile computer must be unpaired on the remote device as well. (Both
devices must be unpaired!)
4.2.6 CONNECTING
1) From the device list above, double-tap a device to find out the available Bluetooth
services.
2) Tap and hold a desired Bluetooth service, e.g. Serial Port Service, to select [Connect]
from the pop-up menu. Once the connection has been established, the connected
service will be displayed along with a plug icon " ".
67
9500CE Mobile Computer Reference Manual
3) If you wish to add a service to the Q_Link list for establishing a quick connection in
the future, tap and hold the service to select [Create Shortcut] from the pop-up
menu.
BLUETOOTH ACTIVESYNC
For ActiveSync via Bluetooth, tap and hold Serial Port Service to select [Connect to
Activesync] from the pop-up menu. It uses COM8 to connect to your computer by
default.
68
Chapter 4
To stop ActiveSync via Bluetooth, tap
Using Applications
and then tap [Connect via Cradle].
USING SERIAL PORT SERVICE
Tap and hold Serial Port Service to select [Connect] from the pop-up menu. If "Auto
, you will need to select a COM port. Once the
Client COM Port" is disabled in
connection has been established, the connected service will be displayed along with a
plug icon " ".
To stop using the service, tap and hold it to select [Disconnect]. The plug icon will
disappear.
USING OBJECT PUSH SERVICE
1) Tap and hold the Object Push service.
2) Select [Push file] to send a file or PIM item, e.g. a business card. (left below)
3) Choose the file you wish to send. (right below)
69
9500CE Mobile Computer Reference Manual
4) The mobile computer will start transferring the file.
USING FILE TRANSFER SERVICE
1) Tap and hold the File Transfer service.
2) Select [Connect] (and assign COM port if necessary).
3) Tap and hold anywhere blank to select [Add file] from the pop-up menu.
4) Choose the file you wish to upload to the remote device.
5) The mobile computer will start transferring the file.
70
Chapter 4
Using Applications
6) To download a file from the remote device, tap and hold a desired file to select [Get
file] from the pop-up menu.
71
9500CE Mobile Computer Reference Manual
4.3 READER CONFIGURATION UTILITY
Reader Configuration Utility is the tool to manage the barcode and RFID readers
integrated on the mobile computer.
1) Go to Start > Programs > ReaderConfig to open the Reader Configuration
Utility.
The associated icon
will appear on the taskbar.
to access the menu that allows you to choose and enable
2) Tap and hold the icon
one or both of the readers. There will be a check mark in front of the reader if it is
enabled.
If the RFID Reader is installed, the option will be available.
3) To meet your application requirements, proceed to configure associated reader
settings as well as barcode settings.
Note: (1) The ReaderConfig utility will automatically detect the reader module(s) that is
currently installed in the mobile computer.
(2) If you wish to reload the default settings, delete the ReaderCfgINI.txt file in
DiskOnChip or tap [Restore Defaults] on the General tab.
72
Chapter 4
Using Applications
4.3.1 CHECKING THE READER STATUS
The barcode reader configurations depend on the scan engine(s) installed. You can tell
which reader is currently in use and make necessary changes on the General tab.
Barcode Reader
Description
CCD/Laser Reader
If installed, tap the [Barcode Reader] button to configure the reader settings
for CCD or Laser scan engine.
(Extra) Long Range
Laser Reader
If installed, tap the [Barcode Reader] button to configure the reader settings
for Long Range Laser or Extra Long Range laser scan engine.
2D Reader
Refer to the Reader Settings Table in Appendix II - CCD/Laser Scan
Engine.
Refer to the Reader Settings Table in Appendix III - LR/ELR Laser Scan
Engine.
The 2D scan engine is capable of reading linear and 2D barcodes.
If installed, tap the [Barcode Reader] button to configure the reader settings
for 2D scan engine.
Refer to the Reader Settings Table in Appendix IV - 2D Scan Engine.
4.3.2 RFID READER SETTINGS
If the RFID scan engine is present, configurable options will be displayed.
Note: Because it is possible to read barcode and RFID tag at the same time, it is
recommended that only one scan engine is enabled at a time to prevent from
misreading.
Some RFID tags support both read/write operations, on a page-by-page basis. You may
find it necessary to define your own read/write operation. For reference only, the table
below lists the start page for read/write operation on a number of RFID tags.
Start Page
Tag Type
Standard
-1
Start from byte 0 of the default page (see below) for all tags
3
Mifare Ultralight
ISO 14443A
4
SR176
ISO 14443B
3
ICODE SLI
ISO 15693
0
LRI512
ISO 15693
3
SRF55VxxP
ISO 15693
0
EM4135
ISO 15693
0
Tag-it HF-I
ISO 15693
0
Others
ISO 15693
5
ICODE
ICODE® (Phillips)
73
9500CE Mobile Computer Reference Manual
Note: Please refer to the specifications of your RFID tags for memory organization.
READ OPERATION
By default, the RFID tag is read from byte 0 of the default page. However, the default
page, amount of bytes and number of pages of each tag may be different. Specify how
many bytes of data you want to read from the tag.
Generally, the read data is user data obtained from the user block. If you are sure that
the data is to be read from a non-user block, such as the lock block, you need to select
the check box of [Display hex values] first.
WRITE OPERATION
Type the string that you want to write to a tag. By default, the string is written to the tag
from byte 0 of the default page. However, the default page, amount of bytes and number
of pages of each tag may be different. Therefore, the input string will automatically be
truncated to fit into pages, and data may be discarded when it comes to the end of pages
available.
Generally, it will write the input string to the user block, which is free for custom use.
The string will be displayed as “user data”. If you wish to write the string to a non-user
block, such as the lock block, you need to select the check box of [Use hex values] first.
Once you have selected to use hex values for the string, make sure the string length
must be even. For example, if you want to write 0x0A, 0x0B and 0x00 to a tag, the
string you input must be “0A0B00” instead of “AB0”.
4.3.3 DATA OUTPUT
Tap the [Data Output] button on the General tab to choose from the three options for
data output after decoding as well as configure associated settings
Default
Data Output
Keyboard
Emulation
Data is emulated as typed text and sent to the active Window.
When “Local machine” is selected, simply run your
application or built-in program, such as WordPad, to start
with data collection.
When “RDP server” is selected, run the Remote Desktop
Connection program to connect to a remote computer.
Local machine
Note that this option is unable to emulate double bytes, such
as Big-5 or Unicode characters on the remote PC.
Windows
Message
When selected, a Windows message will be broadcasted after
decoding.
74
Intercept the decode message in your application.
Call Windows API (ReadMsgQueue) in your application to
retrieve the decoded data.
Disable
Chapter 4
Windows Event
Using Applications
When selected, a Windows event will be broadcasted after
decoding.
Disable
Intercept the decode event in your application.
Call Windows API (ReadMsgQueue) in your application to
retrieve the decoded data.
Note: (1) Refer to CipherLab WinCE Products Programming Guide for details on Windows
Message and Windows Event. Sample programs are provided by request.
(2) For the use of a different program rather than ReaderConfig, a dynamic-link
library (DLL) file is provided.
Auto ENTER
This function can spare you the trouble of pressing the [Enter]
key on the mobile computer to confirm each scan. It will
automatically add an ENTER character in front or to the end of
one scan.
Auto ENTER
Character
No
Scan + ENTER
ENTER + Scan
*Auto ENTER must be enabled.
Scan + ENTER
None
Carriage
Return
Carriage Return
Tab
Space
Comma
Semicolon
Prefix String
0~10 characters
NULL
Suffix String
0~10 characters
NULL
Display Code
Type
Select the check box to prefix the code type to barcode data after Disabled
decoding a barcode.
Display Code
Length
Select the check box to suffix the code length to barcode data
after decoding a barcode.
Disabled
Display RFID
UID
Select the check box to display UID after decoding an RFID tag.
Enabled
Display RFID
User Data
Select the check box to display user data after decoding an RFID
tag.
Disabled
Field Delimiter
Decide whether or not to use a delimiter to separate data fields
after decoding a barcode or an RFID tag —
‘ , ’ (comma)
Code type, barcode data, and code length if more than one
field is displayed
UID and user data if both are displayed
4.3.4 NOTIFICATIONS (FOR GOOD READ)
Tap the [Notifications] button on the General tab to configure associated settings.
75
9500CE Mobile Computer Reference Manual
Sound / Vibration
Default
Good Read via
speaker
Mute, or Sound 1~9
Sound 1
Good Read via
vibrator
0~30 (sec.)
0 (= Disable)
0 = Disable the vibrator
4.3.5 SYMBOLOGY SETTINGS
For barcode settings, tap the Symbologies tab.
Refer to Appendix I - Scan Engine Settings for the symbologies or RFID tags
supported by a scan engine.
Refer to the Symbology Settings Table in Appendix II - CCD/Laser Scan Engine.
Refer to the Symbology Settings Table in Appendix III - LR/ELR Laser Scan Engine.
Refer to the Symbology Settings Table in Appendix IV - 2D Scan Engine.
76
Chapter 4
Using Applications
4.4 INBOX
You can send and receive e-mail by connecting to a POP3 or IMAP4 server. Inbox
provides an e-mail service for each method you use. In addition, you can synchronize the
e-mail messages in Inbox with either Microsoft Outlook or Microsoft Exchange Server on
your computer through the default ActiveSync mail service.
4.4.1 CREATING AN E-MAIL BOX
1) Go to Start > Programs > Inbox to open the Inbox application.
2) Select Services > Options from the menu bar.
3) Tap and drag the dialog box to show the right edge. Tap [Add] to create an e-mail
service.
4) In the Service Name dialog box, select POP3 Mail or IMAP4 Mail for the service type.
Change the name of e-mail service if necessary. Tap [OK].
5) Proceed with the POP3 or IMAP4 Mail Service Definition (from 1/3 to 3/3).
GPRS: Send and Receive e-mail through GPRS connection.
Network Connection: Send and Receive e-mail through Ethernet, 802.11b/g or
Bluetooth PAN connection.
USB Connection: Send and Receive e-mail through USB connection via the cradle.
77
9500CE Mobile Computer Reference Manual
6) After you have successfully created an e-mail service, you may start using it now.
TOOLBAR
Tap and drag the toolbar handle to move it under the menu bar.
Button
Description
See Also
Compose a new message
Compose > New Message
Reply to sender
Compose > Reply to Sender
Reply to all
Compose > Reply to All
Forward this message
Compose > Forward
Delete this message
File > Delete
Synchronize folders (multiple mailboxes for IMAP4)
Services > Synchronize Folders
Send and receive mail manually
Services > Send/Receive Mail
Connect or disconnect
Services > Connect
78
When connected, it will send and receive mail
automatically.
Chapter 4
Using Applications
4.4.2 SYNCHRONIZING INBOX
When you seat the mobile computer in the cradle and connect it to your computer for the
first time, ActiveSync 3.7.1 will guide you through setting up a partnership between the
mobile computer and your desktop computer. Refer to 2.3 Using ActiveSync.
Select the check box of Inbox as shown below, and click [Settings] to configure it.
Note: ActiveSync 4.x does not support Inbox Synchronization. We recommend that you
have ActiveSync 3.7.1 installed on your computer.
79
9500CE Mobile Computer Reference Manual
4.5 BACKUP UTILITY
The CipherLab Backup Utility is provided with OS 1.20.0409.070524 or later versions.
You can easily make copies of data and restore your mobile computer's specific registry
settings, install applications, user data, etc.
To find out your OS version, go to Start > Settings > Control Panel and select
System. Select the Device Name tab.
You may use the backups (.bkp) for these purposes:
Full Restore Operation
Backup all necessary files here (you don't have to select "Registry") so that you can
restore your mobile computer to an operational state following a disaster.
Partial Restore Operation
Backup a few specific files here so that you can restore small numbers of files after
you have deleted them by accident or found them corrupted.
Easy Cloning
Backup everything (including "Registry") necessary for cloning other 9500CE Mobile
Computers.
Now go to Start > Programs > BackupUtility to open the CipherLab Backup Utility.
4.5.1 MANAGING THE REGISTRY
If you are using this backup utility for the first time, you must manually save the system
registry to the DiskOnChip folder first! Tap [Save] now to save the current system
registry to "\DiskOnChip\Sysbak\Registry.dat".
80
Chapter 4
Warning:
Using Applications
As long as you make any changes to the system configurations and
settings, you must tap [Save] to update the system registry here.
Otherwise, it will reload the old registry values in use after a cold boot.
If you wish to reset the current system configurations and settings to defaults, tap [Reset]
to delete the current system registry "\DiskOnChip\Sysbak\Registry.dat". It will then
reload the default registry values after a cold boot.
4.5.2 GETTING READY FOR BACKING UP FILES
Tap the Backup tab and it will automatically start scanning the file system. Within a few
minutes, it will generate a list for the backup operation.
If the items "Wi-Fi" and "Registry" are not listed, it means no Registry.dat and Wifi.dat
are found in "\DiskOnChip\Sysbak\". Take necessary steps before you tap [Refresh] to
refresh the list of available items.
Wi-Fi – Turn on the power to the 802.11b/g module through the Wireless Power
Manager, and then select an available network to connect.
Registry - Go to the Registry tab and tap [Save].
Warning:
You may not be able to backup all data when programs are still running! It
is suggested that you exit all the applications before backup.
4.5.3 BACKING UP FILES
1) Select the items you wish to backup, and tap [Backup].
2) Tap
if you need to save the backup to a different directory or file name (.bkp).
81
9500CE Mobile Computer Reference Manual
By default, it will save the selected items to the DiskOnChip folder by the current date
- the format of filename is "Backup_(4-digit year)(2-digit month)(2-digit date)".
3) Tap [Start] to pack all the selected items into one .bkp file.
4) Once the backup process is completed, tap [Report] to view the log file if necessary.
5) Tap [OK] to close the current window.
Note: If you wish to backup files to this new directory or file name in future runs, you
must tap
82
on the toolbar to save the current settings and exit the application.
Chapter 4
Using Applications
4.5.4 USING BACKUPS FOR RESTORE
After the backup operation, tap the Restore tab and it will automatically start scanning
for any .bkp files. Specify how to use these backups for automatic or manual restore
operation.
2
1
3
Version information is included
since version 1.00.0011
4
If a backup file has been selected for Auto Restore in your last operation, it will be
prefixed with an asterisk on the list. However, if the version of this selected file is found
earlier than 1.00.0010, a warning message “This file is invalid for Auto Restore!” will be
displayed automatically. Close the warning dialog and it will abort the Auto Restore
setting.
Warning:
Remember to tap
to save the change and exit the application.
File Manipulation
Tap [Refresh] to refresh the list of available backups. If a backup file is not desired
any more, select it and tap [Delete].
Auto Restore
Select a desired backup file from the list and tap [AutoRestore]. It will prefix an
asterisk to the selected file, indicating the specific file will be used in the restore
process that starts automatically right after a cold boot.
During Auto Restore, the slider position indicating the system storage space
(Start > Settings > Control Panel > System: Memory tab) will be
automatically restored as well.
Starting from version 1.00.0011, the backup file version is included in “File
Information”. If the selected backup file is generated by an earlier version, such
version information will be blank, and it will not be allowed for Auto Restore! Close
the warning dialog and it will abort the Auto Restore setting. (right above)
83
9500CE Mobile Computer Reference Manual
For version earlier than 1.00.0010, such version information is unavailable (left
above), and you will have to check the version of a backup file by performing a
manual restore and aborting it before it starts. If the selected backup file is generated
by an earlier version, it will fail to auto restore after a cold boot. If the version of the
backup file is up-to-date, it will not display any warning message.
Warning:
For the Auto Restore setting to take effect, you must tap
toolbar to save the current settings and exit the application.
on the
Manual Restore
Depending on specific requirements, you may perform a full or partial restore
manually.
Full Restore Operation
1. Select a desired backup file from the list.
2. Tap [Restore].
3. Tap [Start] to run the restore process.
4. Once the restore process is completed, you will be asked to perform a warm
boot. Tap [No] if you wish to warm boot later. You may tap [Report] to view the
log file if necessary.
Partial Restore Operation
Double-tap a desired backup file from the list.
Select the desired items.
Tap [Restore].
Tap [Start] to run the restore process.
Once the restore process is completed, you will be asked to perform a warm boot. Tap [No]
if you wish to warm boot later. You may tap [Report] to view the log file if necessary.
Warning:
84
(1) You must perform a warm boot after the restore operation!
(2) You may encounter insufficient memory for the restore operation and
be asked to check memory space on the system (SRAM), DiskOnChip, CF
or SD card. If you insist on restoring it without deleting files, data loss or
incomplete restore may occur!
SPECIFICATIONS
PLATFORM, PROCESSOR & MEMORY
Operating System
Microsoft Windows CE 5.0
Central Processor Unit
Intel PXA270 at 520 MHz
Memory
ROM
128 MB non-volatile NAND flash memory
RAM
128 MB on-board SDRAM memory
Expansion Slots
One Secure Digital (SD) card slot for inserting memory card;
One Compact Flash (CF) Type II card slot for memory card or
peripheral card such as GPRS card
COMMUNICATIONS & DATA CAPTURE
Communications
USB via Cradle
USB 1.1 Specification
Host port (type-A) / Device port (type-B)
Ethernet via Cradle
10/100BASE-TX for 10/100 Mbps over twisted pair cable (Cat. 5)
WPAN
Built-in module for Bluetooth Class 2 connectivity
WLAN
Built-in module for 802.11b/g networking
WWAN
Ordering Option - built-in module for GPRS
Data & Image Capture
Barcode Reader
RFID Reader
Ordering options include
CCD (linear imager)
Standard Laser
Long Range Laser
Extra Long Range Laser
2D Imager
Frequency 13.56 MHz
85
9500CE Mobile Computer Reference Manual
ELECTRICAL CHARACTERISTICS
Batteries
Standard Battery Pack
Rechargeable Li-ion battery - 3.7 V, 4000 mAh
Backup Battery
Rechargeable Lithium battery - 3.7 V, 110 mAh
Data retention for at least 6 hours
Power Adapter
Input
AC 100~240 V, 50/60 Hz
Output
DC 6 V, 3.3 A
(Charging & Comm. Cradle, Travel Charger)
DC 6 V, 6 A
(4-Slot Battery Charger)
Working Time (Laser, one scan per 5 seconds)
Batch Mode with backlight
21 hours
Wi-Fi Mode with backlight
20 hours
PHYSICAL CHARACTERISTICS
Color Touch Screen Display
Display
3.5" Transflective TFT-LCD, 65536 colors, LED backlit
Resolution
QVGA
(320 × 240 pixels)
Keypad
Layout
27 keys for alphanumeric layout, LED backlit
Notifications
Status LED
Triple-color LED - Red / Green / Blue
Audio
Mono speaker integrated
Vibrator
9000 ± 2000 RPM, Max. 50 dB
Enclosures
Materials
Rubber & ABS plastic
Dimensions
230 mm (L) 91 mm (W) 63 mm (H)
Weight
Approx. 600 g (including battery, Laser scan engine)
86
Specifications
ENVIRONMENTAL CHARACTERISTICS
Temperature
Operating
-10°C to 50 °C
Storage
-20 °C to 60 °C
Humidity
Operating
10% to 90%, non-condensing
Storage
5% to 95%, non-condensing
Resistance
Impact Resistance
1.5 m, 5 drops per 6 sides
Splash/Dust Resistance
IP 64
Electrostatic Discharge
± 15 kV air discharge, ± 8 kV direct discharge
Regulations
EMC Regulations
FCC, CE, C-Tick, TELEC, RSS-210
PROGRAMMING SUPPORT
Development Environment & Tools
Integrated Development
Environment
Visual Studio 2005
Visual Studio .NET 2003
eMbedded Visual C++ 4.0 SP4
Software Development Kit
9500CE SDK or Windows CE 5.0 Standard SDK
System API (static and DLL) for system configuration
ReaderDLL for reader configuration
Software & Utilities
Reader Configuration Utility
Terminal Emulation for VT100/220 or IBM 5250
Application Generator
STREAM Wireless Studio
Web Browser
Third-party software –
Wavelink Enabler & Telnet Client
MCL Collection - MCL Client
87
9500CE Mobile Computer Reference Manual
ACCESSORIES
Accessory Options
Memory Card, SD or CF
Pistol Grip
Belt Holster
Protective Cover
Spare rechargeable battery pack
4-Slot Battery Charger
Charging & Communication Cradle
Vehicle Cradle
Travel Charger
88
Appendix I
SCAN ENGINE SETTINGS
The Reader Configuration Utility (ReaderConfig.exe) allows configuring the following
reader types, depending on the module equipped on your mobile computer:
1D CCD scan engine
1D Laser scan engine
1D Long Range Laser scan engine
1D Extra Long Range Laser scan engine
2D scan engine
RFID reader
Options of different reader combination are allowed, such as 1D+RFID and 2D+RFID. For
each combination, both readers can be initialized and ready for scanning at the same
time (dual mode operation). For example, if you press the [SCAN] button while running
the ReaderConfig utility on the mobile computer, it will read a barcode in position or an
RFID tag in proximity depending on which one comes first.
Note: (1) You cannot have 1D+2D scan engines installed on the mobile computer
because they are both barcode readers!
(2) You can run only one utility or application at a time to control the reader(s).
For example, while running ReaderConfig.exe, you should not run Application
Generator, STREAM Wireless Studio, MIRROR Browser, or any other application
that uses ReaderDLL.
89
9500CE Mobile Computer Reference Manual
SYMBOLOGIES SUPPORTED
Varying by the scan engine installed, the supported symbologies or tag types are listed
below. For details on configuring associated settings, please refer to each Appendix
separately.
CCD, Laser
LR, ELR
2D
Codabar
9
9
9
Code 11
8
8
9
Code 93
9
9
9
Composite
Code
8
8
9
MSI
9
9
9
Plessey
9
8
8
Postal Codes
8
8
9
Telepen
9
8
8
Code 128
9
9
9
EAN-128
9
9
9
ISBT-128
8
9
9
Industrial 25 (i.e. Discrete 25)
9
9
9
Interleaved 25
9
9
9
Matrix 25
9
8
8
Code 39
9
9
9
Trioptic Code 39
8
9
9
Italian Pharmacode (i.e. Code
32)
9
9
9
French Pharmacode
9
8
8
EAN-8
9
9
9
EAN-13
9
9
9
Bookland EAN (i.e. ISBN)
9
9
9
UPC-E0
9
9
9
UPC-E1
8
9
9
UPC-A
9
9
9
RSS-14
9
9
9
RSS Limited
9
9
9
RSS Expanded
9
9
9
PDF417
8
8
9
MicroPDF417
8
8
9
Code 128
Code 2 of 5
Code 3 of 9
EAN/UPC
RSS
2D
Symbologies
90
Appendix I
Scan Engine Settings
Data Matrix
8
8
9
Maxicode
8
8
9
QR Code
8
8
9
91
9500CE Mobile Computer Reference Manual
RFID TAGS SUPPORTED
The RFID reader supports read/write operations depending on the tags. The supported
labels include ISO 15693, Icode®, ISO 14443A, and ISO 14443B.
Currently, the performance of many tags has been confirmed, and the results are listed
below for your reference. The results found with RFID module version 1.0 are different
from those found with version 0.9 or older versions.
Note: You should study the specifications of RFID tags before use.
RFID Module Version 1.0
UID Only
Read Page
Write Page
ISO 14443A
Mifare Standard 1K
9
9
9
Mifare Standard 4K
9
9
9
Mifare Ultralight
9
9
9
Mifare DESFire
9
---
---
Mifare S50
9
9
9
SLE44R35
9
---
---
SLE66R35
9
9
9
SRIX 4K
9
9
9
SR176
9
9
9
ICODE SLI
9
9
9
SRF55V02P
9
---
---
SRF55V02S
9
---
---
SRF55V10P
9
---
---
TI Tag-it HF-I
9
9
9
ICODE
9
9
9
ISO 14443B
ISO 15693
ICODE®
(Phillips)
92
Appendix II
CCD/LASER SCAN ENGINE
The tables below list reader settings as well as symbology settings for the CCD or Laser
scan engine.
READER SETTINGS TABLE
CCD/Laser
Description
Time-out
Default
3 sec.
1~9 (second) for
ReaderConfig.exe
Set the maximum time for decoding to continue during a scan attempt. It
applies to the following scan modes only –
0~255 (second) for
programming
Aiming mode
Laser mode
Auto Off mode
Auto Power Off mode
Scan Mode
Continuous Mode
Laser mode
Non-stop scanning
Test Mode
Non-stop scanning
Repeat Mode
The scanning won't stop until (a) a barcode is decoded or (b) the
pre-set timeout expires.
Hold down the scan trigger to start with scanning.
Auto Off Mode
The scanning won't stop until you press the trigger again.
Press the scan trigger to aim at a barcode. Within one second, press the
trigger again to decode the barcode.
Laser Mode
The scanning won't stop until you release the trigger.
Press the scan trigger to start with scanning.
Aiming Mode
Capable of re-transmitting barcode data if triggering within one second
after a successful decoding
Hold down the scan trigger to start with scanning.
Alternate Mode
Capable of decoding the same barcode repeatedly
Non-stop scanning
Momentary Mode
To decode the same barcode repeatedly, move away the scan beam
and target it at the barcode for each scanning.
The scanning won't stop until (a) a barcode is read, (b) the preset
timeout expires, or (c) you release the trigger.
Press the scan trigger to start with scanning.
The scanning won't stop until (a) a barcode is read or (b) the preset
timeout expires.
93
9500CE Mobile Computer Reference Manual
Auto Power Off Mode
Press the scan trigger to start with scanning.
The scanning won't stop until the preset timeout expires, and, the
preset timeout period re-counts after each successful decoding.
Read Redundancy
None
None
No redundancy means one successful decoding will make the reading valid
and induce the "READER Event".
One time, Two times,
or Three times
The higher the reading security is (that is, the more redundancy the user
selects), the slower the reading speed gets.
If "Three Times" is selected, it will take a total of four consecutive
successful decodings of the same barcode to make the reading valid.
SYMBOLOGY SETTINGS TABLE
CCD/Laser
Description
Codabar
Select Start/Stop
Characters
Enable
If "Transmit Start/Stop Characters" is desired, select one
set:
Transmit Start/Stop
Characters
Default
abcd / abcd
abcd / abcd
abcd / tn*e
ABCD / ABCD
ABCD / TN*E
Decide whether to include the start/stop characters in the
data being transmitted.
No
Code 128
Enable
EAN-128
Enable
Transmit Code ID
Decide whether to include Code ID (“]C1”) will be included
in the data being transmitted.
No
Industrial 25 (= Discrete 25)
Enable
Start/Stop Selection
This decides the readability of all 2 of 5 symbology
variants. For example, flight tickets actually use an
Industrial 2 of 5 barcode but with Interleaved 2 of 5
start/stop pattern. In order to read this barcode, the
start/stop pattern selection parameter of Industrial 2 of 5
should set to "Interleaved 25".
Industrial 25
Verify Checksum
Decide whether to verify the checksum. If the checksum is No
incorrect, the barcode will not be accepted.
Transmit Checksum
Decide whether to include the checksum in the data being
transmitted.
Yes
Select Length
4~127
One or two fixed lengths
Range
Interleaved 25
Start/Stop Selection
94
Enable
Refer to Industrial 25.
Interleaved
25
Appendix II
CCD/Laser Scan Engine
Verify Checksum
Decide whether to verify the checksum. If the checksum is No
incorrect, the barcode will not be accepted.
Transmit Checksum
Decide whether to include the checksum in the data being
transmitted.
Yes
Select Length
4~127
One or two fixed lengths
Range
Matrix 25
Enable
Start/Stop Selection
Refer to Industrial 25.
Verify Checksum
Decide whether to verify the checksum. If the checksum is No
incorrect, the barcode will not be accepted.
Transmit Checksum
Decide whether to include the checksum in the data being
transmitted.
Yes
Select Length
4~127
One or two fixed lengths
Matrix 25
Range
French Pharmacode
Disable
*Transmit Start/Stop
Character
Controlled by the same setting of Code 39.
No
Transmit Checksum
Decide whether to include the checksum in the data being
transmitted.
Yes
Italian Pharmacode (= Code 32)
Disable
*Transmit Start/Stop
Character
Controlled by the same setting of Code 39.
No
Transmit Checksum
Decide whether to include the checksum in the data being
transmitted.
Yes
Code 39
Enable
Transmit Start/Stop
Character
Decide whether to include the start/stop characters "*" in
the data being transmitted.
No
Verify Checksum
Decide whether to verify the checksum. If the checksum is No
incorrect, the barcode will not be accepted.
Transmit Checksum
Decide whether to include the checksum in the data being
transmitted.
Yes
Code 39 Full ASCII
Code 39 Full ASCII includes all the alphanumeric and
special characters.
Disable
Code 93
Enable
MSI
Disable
Verify Checksum
Select one of the three calculation formulas to verify the
checksum. If the checksum is incorrect, the barcode will
not be accepted.
Single Modulo
10
Single Modulo 10
Double Modulo 10
Modulo 11 & 10
95
9500CE Mobile Computer Reference Manual
Transmit Checksum
Select Length
Decide whether to include the checksum in the data being
transmitted.
Both digits
transmitted
Last digit not transmitted
Both digits transmitted
Both digits not transmitted
One or two fixed lengths
4~127
Range
Negative Barcode
Disable
Plessey
Disable
Convert to UK Plessey
When applied, each occurrence of the character "A" in the
barcode data will be replaced by the character "X".
No
Transmit Checksum
Decide whether to include the checksum (2 digits) in the
data being transmitted.
Yes
Telepen
Disable
Original Telepen
(Numeric)
The original Telepen includes numeric characters.
AIM Telepen (Full
ASCII)
AIM Telepen (Full ASCII) includes all the alphanumeric and No
special characters.
RSS-14
Yes
Disable
Transmit Code ID
Decide whether to include Code ID ("]e0") will be included
in the data being transmitted.
Yes
Transmit Application
ID
Decide whether to include the Application ID ("01") in the
data being transmitted.
Yes
Transmit Checksum
Decide whether to include the checksum in the data being
transmitted.
Yes
RSS Limited
Disable
Transmit Code ID
Refer to RSS-14.
Yes
Transmit Application
ID
Refer to RSS-14.
Yes
Transmit Checksum
Refer to RSS-14.
Yes
RSS Expanded
Transmit Code ID
Disable
Refer to RSS-14.
EAN-8
Yes
Enable
Convert to EAN-13
The EAN-8 barcode will be expanded into EAN-13, and the
next processing will follow the settings configured for
EAN-13.
No
Transmit Checksum
Decide whether to include the checksum in the data being
transmitted.
Yes
Addon 2 / Addon 5
Decide whether to decode EAN-8 with supplementals.
No
EAN-13 / UPC-A
ISBN Conversion
96
Enable
The EAN-13 barcode starting with 978 and 979 will be
converted to ISBN.
No
Appendix II
CCD/Laser Scan Engine
ISSN Conversion
The EAN-13 barcode starting with 977 will be converted to
ISSN.
No
GTIN for EAN-13
The EAN-13 barcode will be expanded into 14-digit Global
Trade Item Number (GTIN).
No
Transmit Checksum
Decide whether to include the checksum in the data being
transmitted.
Yes
Addon 2 / Addon 5
Decide whether to decode EAN-13/UPC-A with
supplementals.
No
(UPC-A) Convert to
EAN-13
The UPC-A barcode will be expanded into EAN-13, and the
next processing will follow the settings configured for
EAN-13.
Yes
(UPC-A) Transmit
Checksum
Decide whether to include the UPC-A checksum in the data Yes
being transmitted.
(UPC-A) Transmit
System Number
Decide whether to include the UPC-A System Number in
the data being transmitted.
UPC-E
Yes
Enable
Convert to UPC-A
The UPC-E barcode will be expanded into UPC-A, and the
next processing will follow the settings configured for
UPC-A.
No
Transmit Checksum
Decide whether to include the UPC-E checksum in the data Yes
being transmitted.
Transmit System
Number
Decide whether to include the UPC-E System Number in
the data being transmitted.
No
Addon 2 / Addon 5
Decide whether to decode UPC-E with supplementals.
No
*It cannot read UPC-E1 barcodes!
97
9500CE Mobile Computer Reference Manual
98
Appendix III
LR/ELR LASER SCAN ENGINE
The tables below list reader settings as well as symbology settings for the Long Range
Laser (LR) or Extra Long Range Laser (ELR) scan engine.
READER SETTINGS TABLE
LR/ELR
Description
Default
Decode Time-out
Set the maximum time for decoding to continue during a
scan attempt.
3.0 sec.
Aiming Time-out
1~9 (second) for ReaderConfig.exe – default to 3
5~99 (0.1 second) for programming – default to 30
Decide whether to have the aiming dot. When you press
the [SCAN] button, the scan engine will emit a red dot for
aiming. It will stay on until it times out or you press the
[SCAN] button again. Then, it will emit a scan beam.
0~9, in units of 1 second.
Enter 0 if aiming is not desired.
Read Redundancy
Level 1
No aiming
Level 1
The following barcodes must be successfully read twice before being
decoded:
Barcode Types
Code Length
Codabar
All
MSI
4 characters or less
Discrete 25 (=Industrial 25)
8 characters or less
Interleaved 25
8 characters or less
Level 2
All barcodes must be successfully read twice before being decoded.
Level 3
All barcodes except for the following barcodes must be successfully read
twice before being decoded. The following barcodes must be read three
times:
Level 4
Barcode Types “Excluded”
Code Length
MSI
4 characters or less
Discrete 25 (=Industrial 25)
8 characters or less
Interleaved 25
8 characters or less
All barcodes must be successfully read three times before being decoded.
99
9500CE Mobile Computer Reference Manual
Scan Angle
Select the scan angle for the Long Range Laser scan
engine.
Narrow
“narrow” 30°
“wide” for 42°
SYMBOLOGY SETTINGS TABLE
LR/ELR/2D
Description
Codabar
CLSI Editing
Enable
When applied, the CLSI editing strips the start/stop
characters and inserts a space after the first, fifth, and
tenth characters of a 14-character Codabar barcode.
NOTIS Editing
Select Length
Default
No
The 14-character barcode length does not include
start/stop characters.
Decide whether to include the start/stop characters in the
data being transmitted.
NOTIS Editing is to strip the start/stop characters, i.e.
to disable "Transmit Start/Stop Characters".
One or two fixed lengths
No
4~55
Range (1~55)
Code 128
---
Code 128
Read standard Code 128 barcodes (=without leading FNC1 Enable
character).
UCC/EAN-128
Read UCC/EAN-128 barcodes with leading FNC1 character. Enable
ISBT 128
Read ISBT 128 barcodes.
Industrial 25 (= Discrete 25)
Select Length
One or two fixed lengths
Verify Checksum
100
4~55
Enable
Convert a 14-character barcode into EAN-13 if the
following requirements are met:
The barcode must have a leading 0 and a valid EAN-13
check digit.
“Verify Checksum” must be disabled.
Decide whether to verify the checksum. If desired, select
one of the algorithms below. If the checksum is incorrect,
the barcode will not be accepted.
Transmit Checksum
Enable
Range (1~55)
Interleaved 25
Convert to EAN-13
Enable
No
No
No
USS algorithm
OPCC algorithm
Decide whether to include the checksum in the data being
transmitted.
No
Appendix III LR/ELR Laser Scan Engine
Select Length
"Verify Checksum" must be enabled so that the
checksum can be left out (= "Transmit Checksum"
disabled).
One or two fixed lengths
4~55
Range (1~55)
Code 39
Enable
Convert to Code 32
Convert to Italian Pharmacode.
No
Code 32 Prefix
Prefix character "A" to Code 32 barcodes.
No
Verify Checksum
Decide whether to verify the checksum. If the checksum is No
incorrect, the barcode will not be accepted.
Transmit Checksum
Decide whether to include the checksum in the data being
transmitted.
No
"Verify Checksum" must be enabled so that the
checksum can be left out (= "Transmit Checksum"
disabled).
Code 39 Full ASCII
Code 39 Full ASCII includes all the alphanumeric and
special characters.
Disable
Select Length
4~55
One or two fixed lengths
Range (1~55)
Trioptic Code 39
Disable
Code 93
Enable
Select Length
One or two fixed lengths
4~55
Range (1~55)
MSI
Verify Checksum
Enable
If Two Check Digits option is selected, an additional
verification is required to ensure integrity. Select one of
the algorithms below. If the checksum is incorrect, the
barcode will not be accepted.
Check Digit
Algorithm
One Check Digit
Single Modulo 10
Two Check Digits
Single Modulo
10
Mod 10/Mod 11
Mod 10/Mod 10
Transmit Checksum
Decide whether to include the checksum in the data being
transmitted.
No
Select Length
4~55
One or two fixed lengths
Range (1~55)
RSS
RSS-14
RSS Limited
RSS Expanded
--"Convert to UPC/EAN" only applies to RSS-14 and RSS
Limited barcodes not decoded as part of a Composite
barcode.
See below.
See below.
See below.
101
9500CE Mobile Computer Reference Manual
Convert RSS to
UPC/EAN
Convert to EAN-13
No
Strip the leading "010" from barcodes.
"01" is the Application ID and must be followed by a
single zero (the first digit encoded)
Convert to UPC-A
Strip the leading "0100" from barcodes.
"01" is the Application ID and must be followed by
two or more zeros (but not six zeros)
Note: (1) RSS-14, RSS Limited, RSS Expanded are all disabled for LR/ELR Laser scan
engine.
(2) RSS-14, RSS Limited, RSS Expanded are all enabled for 2D scan engine.
EAN-8
Enable
Convert to EAN-13
The EAN-8 barcode will be expanded into EAN-13, and the
next processing will follow the settings configured for
EAN-13.
Addon 2 / Addon 5
Refer to UPC/EAN Addon setting.
EAN-13
No
Enable
Bookland EAN (=
ISBN)
The EAN-13 barcode starting with 978 will be converted to
ISBN.
Addon 2 / Addon 5
Refer to UPC/EAN Addon setting.
UPC-A
Yes
Enable
Transmit Checksum
Decide whether to include the UPC-A checksum in the data Yes
being transmitted.
Transmit Preamble
Decide whether to include the UPC-A preamble System
System
Number (and Country Code) in the data being transmitted. Number
Addon 2 / Addon 5
Refer to UPC/EAN Addon setting.
UPC-E0
Enable
Transmit Checksum
Decide whether to include the UPC-E0 checksum in the
data being transmitted.
Transmit Preamble
Decide whether to include the UPC-E0 preamble System
System
Number (and Country Code) in the data being transmitted. Number
Addon 2 / Addon 5
Refer to UPC/EAN Addon setting.
Convert to UPC-A
The UPC-E0 barcode will be expanded into UPC-A, and the
next processing will follow the settings configured for
UPC-A.
UPC-E1
Yes
No
Disable
Transmit Checksum
Decide whether to include the UPC-E1 checksum in the
data being transmitted.
Transmit Preamble
Decide whether to include the UPC-E1 preamble System
System
Number (and Country Code) in the data being transmitted. Number
102
Yes
Appendix III LR/ELR Laser Scan Engine
Addon 2 / Addon 5
Refer to UPC/EAN Addon setting.
Convert to UPC-A
The UPC-E1 barcode will be expanded into UPC-A, and the
next processing will follow the settings configured for
UPC-A.
UCC Coupon Extended Code
No
Disable
Read UPC-A barcodes starting with digit "5", EAN-13 barcodes starting with digits "99", and
UPC-A/EAN-128 Coupon Codes.
UPC-A, EAN-13, and EAN-128 must be enabled first!
Use “Addon Redundancy” to control auto-discrimination of the EAN-128 (right half) of a coupon
code.
UPC/EAN Addon
Addon 2 / Addon 5
--Decide whether to decode EAN-8, EAN-13, UPC-E0,
UPC-E1, UPC-A with supplementals.
Addon Redundancy
Ignore…
Ignore Supplementals
Decode Only With Supplementals
Decode With Supplementals (= Auto-discriminate)
When “Decode with Supplementals” is applied, decide the
number of times of supplementary decoding the same
barcode that makes a valid reading.
See below.
Note: (1) Addon Redundancy is set to 14 times for LR/ELR Laser scan engine.
(2) Addon Redundancy is set to 10 times for 2D scan engine.
Miscellaneous Options
Transmit Code ID
---
Decide whether to include AIM Code ID in the beginning of Disable
data. Each AIM Code ID contains the three-character
string “]cm” –
] = Flag Character (ASCII 93)
c = Code Character (see below)
m = Modifier Character (see below)
AIM CODE ID – CODE CHARACTERS
Code Character
Code Type
A
Code 39
C
Code 128
E
UPC/EAN
F
Codabar
G
Code 93
H
Code 11
I
Interleaved 25
M
MSI
S
Discrete 25, IATA 2 of 5
103
9500CE Mobile Computer Reference Manual
X
Code 39 Trioptic, Bookland EAN
AIM CODE ID – MODIFIER CHARACTERS
Code Type
Option Value
Option
Code 39
0
No check character or Full ASCII processing.
1
Checksum has been verified.
3
Checksum has been verified and stripped.
4
Full ASCII conversion has been performed.
5
Result of option values 1 and 4.
7
Result of option values 3 and 4.
0
Standard data packet. No Function Code 1“FNC1” in the first
character position.
1
Function Code 1“FNC1” in the first character position.
2
Function Code 1“FNC1” in the second character position.
0
No check digit processing.
1
Checksum has been verified.
3
Checksum has been verified and stripped.
Codabar
0
No check digit processing.
Code 93
0
Always transmit 0.
MSI
0
Modulo 10 check digit verified and transmitted.
1
Modulo 10 check digit verified but not transmitted.
Discrete 25
0
Always transmit 0.
UPC/EAN
0
Standard data packet in full EAN country code format, which
is 13 digits for UPC-A and UPC-E (not including
supplemental data).
1
Two-digit supplemental data only.
2
Five-digit supplemental data only.
4
EAN-8 data packet.
Code 128
Interleaved 25
A UPC-A with Addon 2 barcode, 012345678905-10, is transmitted to the
host as a 21-character string, ]E00012345678905]E110.
Bookland EAN
0
Always transmit 0.
Trioptic Code 39
0
Always transmit 0.
104
Appendix IV
2D SCAN ENGINE
The tables below list reader settings as well as symbology settings for the 2D scan
engine.
READER SETTINGS TABLE
2D
Description
Default
Decode Time-out
Set the maximum time for decoding to continue during a
scan attempt.
3.0 sec.
Focus Mode
Near Focus – optimized to read at its near position
Smart Focus – toggles the focus position after every
frame
Turn Off
On
Turn On
Turn Off
Read Redundancy
Level 1
On
Turn On (Internal LED )
Decide whether to project the aiming pattern during
barcode capture.
Far Focus
Far Focus – optimized to read at its far position
Decide whether to flash illumination on every barcode
capture to aid decoding.
Aiming Pattern
5~99 (0.1 second) for programming – default to 30
Select the focus mode to control the working range:
Decode Illumination
1~9 (second) for ReaderConfig.exe – default to 3
Level 1
The following barcodes must be successfully read twice before being
decoded:
Barcode Types
Code Length
Codabar
8 characters or less
MSI
4 characters or less
Discrete 25 (=Industrial 25)
8 characters or less
Interleaved 25
8 characters or less
Level 2
All barcodes must be successfully read twice before being decoded.
Level 3
All barcodes except for the following barcodes must be successfully read
twice before being decoded.
105
9500CE Mobile Computer Reference Manual
The following barcodes must be read three times:
Barcode Types “Excluded”
Code Length
Codabar
8 characters or less
MSI
4 characters or less
Discrete 25 (=Industrial 25)
8 characters or less
Interleaved 25
8 characters or less
Level 4
All barcodes must be successfully read three times before being decoded.
Security Level
Select a decode security level appropriate for the barcode
quality when reading delta barcodes such as Code 128,
Code 93, UPC/EAN.
Security Level 0 – This default setting allows the scan
engine to operate in its most aggressive state,
providing sufficient security in decoding most “in-spec”
barcodes.
Security Level 1 – Select this option if misdecodes
occur. This level should eliminate most misdecodes.
Security Level 2 – Select this option if Security Level 1
fails to eliminate misdecodes.
Security Level 3 – Select this option if Security Level 2
also fails to eliminate misdecodes. However, selecting
this option impairs the decoding ability of the scan
engine. If this level of security is necessary, try to
improve the barcode quality.
Level 0
SYMBOLOGY SETTINGS TABLE
The symbology settings for the LR/ELR scan engine are all supported on the 2D scan engine. In
addition, the 2D scan engine supports the following symbology settings:
2D
Description
Code 11
Verify Checksum
Enable
Decide whether to verify the checksum. If the checksum is No
incorrect, the barcode will not be accepted.
Transmit Checksum
Select Length
Default
No verification
One Check Digit
Two Check Digits
Decide whether to include the checksum in the data being
transmitted.
"Verify Checksum" must be enabled so that the
checksum can be left out (= "Transmit Checksum"
disabled).
One or two fixed lengths
No
4~55
Range (1~55)
Postal Codes
---
US Postnet
Enable
106
Appendix IV
US Planet
Transmit US Postal
Checksum
Enable
US Postnet or US Planet must be enabled first!
UK Postal
Transmit UK Postal
Checksum
2D Scan Engine
Enable
Enable
UK Postal must be enabled first!
Enable
Japan Postal
Enable
Australian Postal
Enable
Dutch Postal
Enable
Composite Codes
---
Composite CC-C
Enable
Composite CC-A/B
Disable
Composite TLC-39
Disable
UCC/EAN Code 128
Emulation Mode
Transmit data as if it was encoded in Code 128 barcodes.
UPC Composite Mode
UPC barcodes can be "linked" with a 2D barcode during
transmission as if they were one barcode.
Disable
Transmit AIM Code Identifier must be enabled first!
UPC Always
Linked
UPC Never Linked
Transmit UPC barcodes regardless of whether a 2D
barcode is detected.
UPC Always Linked
Transmit UPC barcodes and the 2D portion. If the 2D
portion is not detected, the UPC barcode will not be
transmitted.
CC-A/B or CC-C must be enabled!
Auto-discriminate UPC Composites
Transmit UPC barcodes as well as the 2D portion if
present.
2D Symbologies
---
PDF417
Enable
MicroPDF417
Disable
MicroPDF417 Code 128 Transmit data from certain MicroPDF417 barcodes as if it
Emulation
was encoded in Code 128 barcodes.
Disable
Transmit AIM Code Identifier must be enabled first!
When applied, the MicroPDF417 barcodes are transmitted
with one of these prefixes:
The first codeword of MicroPDF417 is 903-907, 912, 914,
915:
The original Code ID "]L3" will be changed to "]C1".
107
9500CE Mobile Computer Reference Manual
The first codeword of MicroPDF417 is 908 or 909:
The original Code ID "]L4" will be changed to "]C2".
The first codeword of MicroPDF417 is 910 or 911:
The original Code ID "]L5" will be changed to "]C0".
Data Matrix
Enable
Maxicode
Enable
QR Code
Enable
2D Symbologies - Macro PDF
---
Macro PDF is a special feature for concatenating multiple PDF barcodes into one file, known as
Macro PDF417 or Macro MicroPDF417.
Transmit/Decode Mode Decide how to handle Macro PDF decoding.
Passthrough
All Symbols
Buffer All Symbols / Transmit Macro PDF When Complete
Transmit all decoded data from an entire Macro PDF
sequence only when the entire sequence is scanned and
decoded. If the decoded data exceeds the limit of 50
symbols, no transmission because the entire sequence
was not scanned!
Transmit Any Symbol in Set / No Particular Order
Transmit data from each Macro PDF symbol as decoded,
regardless of the sequence.
Passthrough All Symbols
Transmit and decode all Macro PDF symbols and
perform no processing.
In this mode, the host is responsible for detecting and
parsing the Macro PDF sequences.
ESC Characters
When enabled, it uses the backslash "\" as an Escape
character for systems that can process transmissions
containing special data sequences. It will format special
data according to the Global Label Identifier (GLI)
protocol, which only affects the data portion of a Macro
PDF symbol transmission. The Control Header, if enabled,
is always sent with GLI formatting.
None
Note: When printing barcodes, keep each Macro PDF sequence separate, as each has a
unique identifier. Do not mix barcodes from several Macro PDF sequences, even if
they encode the same data. When you scan Macro PDF sequences, scan the entire
Macro PDF sequence without interruption!
108
Appendix IV
2D Scan Engine
Image Capture
Image Capture
Illumination
Disable
Decide whether to flash illumination on every image
capture to aid decoding.
On
Turn On (Internal LED )
Turn Off
Image Capture
Autoexposure
Decide whether to manually specify the gain and exposure
time (only recommended for advanced users with difficult
image capture situations).
On
Gain Time
Only applies when Image Capture Autoexposure is
disabled.
100
Exposure Time
Gain is a means of amplifying the raw image data
before it is converted into 256 grayscale values.
Increasing the gain increases brightness and contrast,
but also increases noise (undesired electrical
fluctuations in the image) which makes the image less
attractive and/or harder to decode.
Set the manual gain time in the range of 79~127.
Only applies when Image Capture Autoexposure is
disabled.
Exposure Time controls the amount of time the CCD is
allowed to collect light, much like the shutter speed for
a camera. Generally, the brighter the environment, the
lower the exposure time. Increasing the exposure time
past 20 ms in a handheld application increases the risk
of blurring the image due to hand jitter.
Set the manual exposure time to one of the following
values — 5 ms, 10 ms, 15 ms, 20 ms, 25 ms, or 30
ms.
10 ms
Snapshot Aiming
Pattern
Decide whether to project the aim pattern while capturing
an image.
Image Resolution
640×480
Decide how to alter image resolution before compression.
Multiple pixels are combined to one pixel, resulting in a
smaller image containing the original content with reduced
resolution.
Image Format
640×480 (Full resolution)
320×240 (Half resolution)
212×160 (1/3 resolution)
160×1420 (1/4 resolution)
Decide in which file format the image is saved.
JPEG
JPEG file format
BMP file format
Optimized for JPEG
Quality
Decide whether JPEG images are optimized for quality.
Select JPEG Quality
Set a value from 5 to 100, where “100” represents the
highest quality image.
On
Enable
Cancel the check box so that JPEG images are
optimized for size.
65
109
9500CE Mobile Computer Reference Manual
Select JPEG Size
Set a value from 5 to 150, which represents the file size in 40
multiples of 1024 bytes (1K). For example, setting this
value to 8 permits the file size to be as large as 8192
bytes.
Bits per Pixel
Select the number of significant bits per pixel (BPP) to use
when capturing an image.
8
1 bit per pixel (for black and white images)
4 BPP (to assign 1 of 16 levels of grey to each pixel)
8 BPP (to assign 1 of 256 levels of grey to each pixel)
Note: (1) For JPEG files, these BPP settings are ignored for it always uses 8 bits per pixel!
(2) When the image capture feature is enabled, press the [SCAN] button and it will
capture an image instead of reading a barcode.
Miscellaneous Options
Transmit Code ID
---
Decide whether to include AIM Code ID in the beginning of Disable
data. Each AIM Code ID contains the three-character
string “]cm” –
] = Flag Character (ASCII 93)
c = Code Character (see below)
m = Modifier Character (see below)
AIM CODE ID – CODE CHARACTERS
Code Character
Code Type
A
Code 39, Code 39 Full ASCII, Code 32
C
Code 128, Coupon (Code 128 portion)
d
Data Matrix
E
UPC/EAN, Coupon (UPC portion)
e
RSS Family
F
Codabar
G
Code 93
H
Code 11
I
Interleaved 25
L
PDF417, Macro PDF417, Micro PDF417
M
MSI
Q
QR Code
S
Discrete 25, IATA 2 of 5
U
Maxicode
X
Code 39 Trioptic, Bookland EAN, US Postnet, US Planet, UK Postal, Japan
Postal, Australian Postal, Dutch Postal
110
Appendix IV
2D Scan Engine
AIM CODE ID – MODIFIER CHARACTERS
Code Type
Option Value
Option
Code 39
0
No check character or Full ASCII processing.
1
Checksum has been verified.
3
Checksum has been verified and stripped.
4
Full ASCII conversion has been performed.
5
Result of option values 1 and 4.
7
Result of option values 3 and 4.
0
Standard data packet. No Function Code 1“FNC1” in the first
character position.
1
Function Code 1“FNC1” in the first character position.
2
Function Code 1“FNC1” in the second character position.
0
No check digit processing.
1
Checksum has been verified.
3
Checksum has been verified and stripped.
Codabar
0
No check digit processing.
Code 93
0
Always transmit 0.
MSI
0
Modulo 10 check digit verified and transmitted.
1
Modulo 10 check digit verified but not transmitted.
Discrete 25
0
Always transmit 0.
UPC/EAN
0
Standard data packet in full EAN country code format, which
is 13 digits for UPC-A and UPC-E (not including
supplemental data).
3
Standard data packet with two-digit or five-digit
supplemental data.
4
EAN-8 data packet.
Code 128
Interleaved 25
A UPC-A with Addon 2 barcode, 012345678905-10, is transmitted to the
host as a 18-character string, ]E3001234567890510.
Bookland EAN
0
Always transmit 0.
Trioptic Code 39
0
Always transmit 0.
Code 11
0
Single check digit (has been verified.)
1
Two check digits (has been verified.)
3
Checksum has been verified but not transmitted.
0
Always transmit 0.
RSS Family
RSS-14 and RSS Limited will be transmitted with an Application Identifier
“01”. For example, an RSS-14 barcode, 100123456788902, is transmitted
as ]e001100123456788902.
111
9500CE Mobile Computer Reference Manual
Note: In UCC/EAN-128 emulation mode, RSS is transmitted using Code 128 rules (i.e.
“]C1”).
EAN.UCC
Composites (RSS,
UCC/EAN-128, 2D
portion of UPC
composite)
Native mode transmission
0
Standard data packet
1
Data packet containing the data following an encoded
symbol separator character.
2
Data packet containing the data following an escape
mechanism character. The data packet does not support the
ECI protocol.
3
Data packet containing the data following an escape
mechanism character. The data packet supports the ECI
protocol.
UCC/EAN-128 emulation
1
Data packet is a UCC/EAN-128 barcode (i.e. data is
preceded with “]JC1”).
Note: UPC portion of composite is transmitted using UPC rules.
PDF417,
0
Micro PDF417
Scan engine is set to conform to protocol defined in 1994
PDF417 symbology specifications.
When this option is transmitted, the receiver cannot
reliably determine whether ECIs have been invoked or
whether data byte 92DEC has been doubled in
transmission.
1
Scan engine is set to follow the ECI protocol (Extended
Channel Interpretation). All data characters 92DEC are
doubled.
2
Scan engine is set for Basic Channel operation (no escape
character transmission protocol). Data characters 92DEC
are not doubled.
When decoders are set to this mode, unbuffered Macro
symbols and symbols requiring the decoder to convey
ECI escape sequences cannot be transmitted.
3
The barcode contains a UCC/EAN-128 symbol, and the first
codeword is 903-907, 912, 914, 915.
4
The barcode contains a UCC/EAN-128 symbol, and the first
codeword is in the range 908-909.
5
The barcode contains a UCC/EAN-128 symbol, and the first
codeword is in the range 910-911.
A PDF417 barcode, ABCD, with no transmission protocol enabled, is
transmitted as ]L2ABCD.
Data Matrix
112
0
ECC 000-140, not supported.
1
ECC 200.
2
ECC 200, FNC1 in first or fifth position.
3
ECC 200, FNC1 in second or sixth position.
Appendix IV
Maxicode
QR Code
2D Scan Engine
4
ECC 200, ECI protocol implemented.
5
ECC 200, FNC1 in first or fifth position, ECI protocol
implemented.
6
ECC 200, FNC1 in second or sixth position, ECI protocol
implemented.
0
Mode 4 or 5
1
Mode 2 or 3
2
Mode 4 or 5, ECI protocol implemented.
3
Mode 2 or 3, ECI protocol implemented in secondary
message.
0
Model 1
1
Model 2, ECI protocol not implemented.
2
Model 2, ECI protocol implemented.
3
Model 2, ECI protocol not implemented, FNC1 implied in first
position.
4
Model 2, ECI protocol implemented, FNC1 implied in first
position.
5
Model 2, ECI protocol not implemented, FNC1 implied in
second position.
6
Model 2, ECI protocol implemented, FNC1 implied in second
position
113