RCA DRC97283 Car Video System User Manual

RCA DRC97283 Car Video System User Manual
9. 10.
11.
12.
13.
14.
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with a dry cloth.
Do not block the ventilation openings. Install in accordance with the manufacturer's instructions.
Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
Do not defeat the safety purpose of the polarized or grounding - type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide
blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult
an electrician for replacement of the obsolete outlet.
Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and
the point where they exit from the apparatus.
Only use attachments/accessories specified by the manufacturer.
Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with
the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to
avoid injury from tip-over.
Unplug this apparatus during lightning storms or when unused for long periods of time.
Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged
in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into
the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been
dropped.
Using the Remote Control
• Point the remote control at the REMOTE SENSOR located on the
unit. The remote controls are color-coded. Use the remote control
with the player that has the color mark corresponding to the
button color of the remote control.
• When using this unit in very bright light, the infrared REMOTE
SENSOR may not work properly.
• The maximum effective distance for remote operation is about 16
feet (5 meters).
Remove the PLASTIC
sheet before using the
Remote Control.
1
To the cigarette lighter socket
DC IN 9V2 To
12V jack
1. Open the battery door.
2. Insert one CR2025 (3V) size battery.
Audio CDs
[8cm/12cm disc]
12
13
Note: If the remote control is not going to be used for a long time, remove the battery.
WARNING: Do not dispose of the battery in a fire or it may leak and/or explode.
WARNING: Batteries shall not be exposed to excessive heat such as sunshine, fire or the like.
CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.
Compatible
Region Management Information
Region Management Information: This unit is designed and manufactured to respond to the Region Management Information
that is encoded on DVDs. If the region number printed on the DVD does not correspond to the region number of this unit, it
cannot play that disc.
Cautions:
Use the provided 12V car power adapter/splitter only. Use with other car power adapters/splitters could damage the unit.
The 12V car power adapter/splitter included with this unit are for its use only. Do not use them with other equipment.
In the interest of traffic safety, do not operate this unit or view videos while driving a vehicle.
Make sure the unit is securely fastened to prevent it from falling or flying through the air in the event of an accident.
If the inside of the cigarette lighter socket is dirty with ashes or dust, the plug section may become hot due to poor
contact. Be sure to clean the cigarette lighter socket before use.
• After use, disconnect the 12V car power adapter/splitter from both the unit and cigarette lighter socket.
•
•
•
•
•
15
16
1) Button
Press the
button to open the front panel, press the
inside disc switch to open the disc door.
2) STANDBY Indicator
When the STANDBY / ON switch is slided to STANDBY
position, the red light will illuminate.
3)
SEARCH Button
Performs fast reverse playback.
SEARCH Button
Performs fast forward playback.
4)
PREV Button
Goes back to current or previous chapters/tracks.
NEXT Button
Advances chapters/tracks.
5)
Flip Button
Flips the screen image.
6)
PAUSE Button
Pauses playback of a disc. Each time you press the
PAUSE button the picture advances one frame on a
DVD. Press the
PLAY button to resume playback.
7)
STOP Button
Stops playing a disc.
8)
PLAY Button
Starts or resumes playback of a disc.
9)LCD Screen
10)Remote Sensor
Receives the remote control signal.
11) Headphone Jack
12) VOLUME Control
Adjusts the volume.
13) Standby/On Switch
14) AUDIO & VIDEO IN / OUT Jacks
15) AV IN / DVD Switch
16) DC IN 9V-12V Jack
The region number of this unit is 1.
power supply
Disc Function or Operation that is Not Available
When the
symbol appears on the screen, it indicates that the function or operation attempted is not available at that time.
This occurs because the DVD manufacturer determines the specific functions of DVDs. Certain functions may not be available
on some DVDs. Be sure to read the documentation provided with the DVD.
Icons Used on DVDs
AC Power Adapter
Screen aspect ratio
1
Multiple camera angles
To AC outlet
Region code indicator
1)
Title, Chapter and Tracks
• DVDs are divided into “titles” and “chapters”. If the disc has more than
one movie on it, each movie would be a separate “title”. “Chapters” are
sections of titles.
Title1
Chapter1
Title2
Chapter2
Chapter3
Chapter1
Chapter2
• Audio CDs are divided into “tracks”. A “track” is usually one song on an
Audio CD.
Track1
Track2
Track3
Track4
Track5
Note: Numbers identify each title, chapter, and track on a disc. Most discs have these numbers recorded on them, but some do
not.
Notes on Unauthorized Discs
You may not be able to play some DVDs on this unit, particularly if they were purchased from outside your geographic area or
made for business purposes.
SOUND SYSTEM
Dolby Digital
Dolby Digital is a technology developed by Dolby Laboratories. Soundtracks encoded in Dolby Digital can reproduce from one
to 5.1 discrete channels of excellent quality audio.
The unit automatically recognizes the Dolby Digital bitstream and provides a downmix suitable for two-channel listening. An
additional Dolby Digital decoder is required for reproduction of the discrete multi-channel soundtracks available on many
DVDs.
Manufactured under license from Dolby Laboratories.
"Dolby" and the double-D symbol are trademarks of Dolby Laboratories.
ACCESSORIES
1. Slide the STANDBY / ON switch on the top of the unit to the ON position.
2. The DVD logo (start-up picture) will appear on the screen.
3. After use, slide the STANDBY / ON switch to the STANDBY (power off ) position.
SAFETY WARNING!
• This unit should never be used by the vehicle's driver or left unsecured in the vehicle while driving.
• If this unit is being used in your vehicle, be sure that it is secured or held safely, and does not
obstruct any safety device, including air bags or seat belts.
• All passengers should wear seat belts when using this unit in a moving vehicle.
• If in doubt, please contact your vehicle manufacturer for further advice.
CONNECTIONS
A. Connecting both Units to Watch one DVD
You can watch the same DVD on the both units at the same time.
Limited Warranty
Audio/Video Cable
(included)
AVC MULTIMEDIA (“AVC”) makes the following limited warranty. This limited warranty extends to the original consumer
purchaser and is limited to non-commercial use of the product.
One Year Parts & Labor Warranty
AVC products purchased in the United States are warranted to be free from defects in materials or workmanship for a period of
one year from the date of their original retail purchase. If the unit fails to conform to this warranty, we will service the product
using new or refurbished parts and products, at AVC’s sole discretion.
The supplied AC power adapter operates on AC 100-120V ~50/60Hz.
Language selections for subtitles
Note:
When playing back a CD-G (Graphics) or CD EXTRA disc, the
audio portion will be played, but the graphic images will not
be shown.
Turning on the unit
A. Using the AC Power Adapter
Language selections for audio
Sample lcons
DC IN 9V2 To
12V jack
3
4
14
BATTERY REPLACEMENT
When the battery becomes weak, the operating distance of the remote control will be greatly reduced and you will need to
replace the battery.
Remote Control
DVDs
[8cm/12cm disc]
Car Power Splitter
TO CHANGE REMOTE BATTERY
Disc Formats
INSTALLATION GUIDE
The 12V car power splitter allows the units to be used with vehicles that have a 12V, negative ground electrical system.
control REFERENCE GUIDE
This unit can play
C. Using the Car Power Splitter
Yellow Black
1.
2. 3. 4. 5. 6. 7. 8. Unit
remote control
Yellow Black
Important Safety Instructions
2)
3)
4)
5)
6)
7)
8)
VIDEO MODE Button
Adjusts Brigntness, Contrast, Color or View Mode of
the LCD screen.
PREV Button
Goes back to current or previous chapters/tracks.
/
SEARCH Buttons
SEARCH: Fast reverse playback.
SEARCH: Fast forward playback.
GOTO Button
Skips directly to a location on a DVD or a CD.
Cursor ( , , , ) Buttons
Use to move between selections on a menu screen
and adjust certain settings.
ENTER Button
Confirms selections on a menu screen.
MEMORY Button
In STOP mode, sets titles/chapters in a favorite order.
Number (0 - 9) Buttons
Use when creating programs and locating a title/
chapter or specific time.
REPEAT A-B Button
Performs point-to-point repeat playback on a DVD or
CD.
REPEAT DISC Button
Repeats a DVD chapter or title.
Repeats a CD track or the entire disc.
SETUP Button
Opens and closes the SETUP menu while in stop
mode.
9)
10)
11)
12)
13)
14)
15)
SUBTITLE Button
Selects one of the subtitle languages programmed on
a DVD (if available).
RETURN Button
Returns to normal operation after using the SETUP
menu of a DVD.
AUDIO Button
Selects one of the audio sound tracks programmed on
a DVD or select the audio output mode on an Audio
CD.
ANGLE Button
Switches between multiple camera angles when the
DVD you are playing has been programmed with
multiple camera angles.
DISPLAY Button
Shows status information on the screen.
STOP Button
Stops playing a disc.
PLAY Button
Starts or resumes playback of a disc.
PAUSE Button
Pauses playback of a disc. Each time you press the
PAUSE button the picture advances one frame on a
DVD. Press the PLAY button to resume playback.
NEXT Button
Advances chapters/tracks.
MENU Button
Opens and closes the DVD menu.
IMPORTANT NOTE:
The included remote controls have different color keys to identify which unit they operate.
The remote control with green keys operates the unit which has green mark on the front of the unit.
The remote control with blue keys operates the unit which has blue mark on the front of the unit.
Please check and identify the supplied accessories.
• To order accessories visit website http://www.RCAav.com
DC IN 9V2 To
12V jack
Watching the same DVD on both units
1. Turn on the units. Slide the AV IN / DVD switch on the unit in which the DVD disc is loaded to DVD position. (Control DVD
playback with this unit and its remote control.)
2. Slide the AV IN / DVD switch on the other unit to AV IN position.
B. Using Headphones / Earphones
• Turn down the volume before connecting, and then
adjust the level.
• When headphones/earphones are connected, no sound
will be emitted from the unit's speaker.
Packaging and Shipping Instruction
When you send the product to the AVC service facility you must use the original carton box and packing material or an
equivalent as designated by AVC.
LIMITED WARRANTY
Headphones / Earphones
(3.5mm diameter plug)
Caution: Avoid listening to sound at levels
which may be harmful to your ears.
Cautions:
• The AC power adapter included with this unit is for its use only. Do not use it with other equipment.
• When the unit is not going to be used for long time, disconnect the AC power adapter from the AC power outlet.
• When the AC power adapter is plugged in, the apparatus is not completely disconnected from the main power supply,
even when the power is turned off.
Warning:
The AC power adapter is used as disconnect device and it should remain readily operable during intended used. In order
to disconnect the apparatus from the mains completely, the AC power adapter should be disconnected from the mains
socket outlet completely.
FOR DESKTOP USE
You can flip up the display for desk-top or table-top viewing.
All warranties implied by state law, including the implied warranties of merchantability and fitness for a particular purpose, are
expressly limited to the duration of the limited warranties set forth above. With the exception of any warranties implied by state
law as hereby limited, the foregoing warranty is exclusive and in lieu of all other warranties, guarantees, agreements and similar
obligations of manufacturer or seller with respect to the repair or replacement of any parts. In no event shall AVC be liable for
consequential or incidental damages.
INSTALLING IN A VEHICLE
Use the supplied mounting straps to install the units on the back of the vehicle's headrests. Tightly wrap the mounting straps
around the headrest.
Mounting Strap
Mounting Strap
To the cigarette lighter socket
Remote Control (with battery)...........................................................................................................................................................................x 2
AC Power Adapter..................................................................................................................................................................................................x 2
Car Power Adapter.................................................................................................................................................................................................x 1
Car Power Splitter...................................................................................................................................................................................................x 1
Mounting Strap.......................................................................................................................................................................................................x 2
Audio/Video Cable.................................................................................................................................................................................................x 1
Out of Warranty
Hours: Monday–Thursday: 9am–7pm, Friday: 9am–5pm, Saturday: 9am–NOON Eastern time.
Important: You are responsible for any transportation, shipping or insurance relative to the return of product to our
Product Returns Center.
The 12V car power adapter allows the unit to be used with vehicles that have a 12V, negative ground electrical system.
1 Car Power Adapter
Your Responsibility
(1) You must retain the original sale receipt to provide proof of purchase.
(2) These warranties are effective only if the product is purchased and operated in the U.S.A. or Canada.
(3) Warranties extend only to defects in material or workmanship, and do not extend to any product or parts which have been
lost or discarded, or damage to product or parts caused by misuse, accident, improper operation or maintenance, or use in
violation of instructions provided with the product, or to product which has been altered or modified without authorization
of AVC, or to products or parts thereof which have had the serial number removed or changed.
In the event your product requires repair after the limited warranty period has expired, please contact our Customer
Support Center at 1-800-506-5746, 1-877-252-6873 or www.RCAav.com
B. Using the Car Power Adapter
WARNING:
Disconnect the car power
adapter when not in use. Not
for use in 24V vehicles.
During a period of one year from the effective warranty date, AVC will provide, when needed, service labor to repair a
manufacturing defect at its designated Service Center. To obtain warranty service in the United States, you must first call
our Customer Support Center at 1-800-506-5746 or 1-877-252-6873, during the hours listed in the box below. The
determination of service will be made by AVC Customer Support. PLEASE DO NOT RETURN YOUR UNIT TO AVC WITHOUT
PRIOR AUTHORIZATION. New or remanufactured replacements for defective parts or products will be used for repairs by
AVC at its designated Service Center for one year from the effective warranty date. Such replacement parts or products are
warranted for an additional one year from the date of repair or replacement. The Customer will be required to ship the unit
to the Service Center indicated at the time Customer Support is contacted to make the necessary repairs. The customer is
responsible for all transportation charges to the service facility.
No person, agent, distributor, dealer or company is authorized to change, modify or extend the terms of these warranties in any
manner whatsoever. The time within action must be commenced to enforce any obligation of AVC arising under the warranty
or under any statute, or law of the United States or any state thereof, is hereby limited to one year from the date of purchase.
This limitation does not apply to implied warranties arising under state law.
This warranty gives you specific legal rights and you may also have other rights, which may vary, from state to state. Some states
do not allow limitation on how long an implied warranty lasts, when an action may be brought, or the exclusion or limitation of
incidental or consequential damages, so the above provisions may not apply to you.
For more information on other products and services, please visit our web site at
www.RCAav.com
2
Important: Also keep your “Bill of Sale” as proof of purchase.
To DC IN 9V12V jack
Model no.......................................................................................................... Product name..................................................................................................
Type of set.......................................................................................................................................................................................................................................
Serial no............................................................................................................ Invoice no..........................................................................................................
Date purchased.............................................................................................. Dealer name.....................................................................................................
FOR SERVICE AND REPAIR, PLEASE VISIT www.RCAav.com
E-2
PVS72830 IB UL English RCA W011.indd 1
E-3
E-4
E-5
E-6
2010-2-2 17:47:25
Playing a Disc
This owner’s manual explains the basic instructions for operating this unit. Some DVDs are produced in a manner
that allows specific or limited operation during playback. Therefore, this unit may not respond to all operating
commands. THIS IS NOT A DEFECT. Please refer to the instructions accompanying the specific DVD in question for
more information about the options available on that DVD.
“ ” may appear on the screen during operation. A “
unit or disc.
” means that the desired operation is not permitted by the
You can play a specific title or chapter repeatedly. (Title repeat, chapter repeat, A-B repeat)
Repeating a Chapter
DVD
1. While the DVD is playing, press the REPEAT DISC button until the “
current chapter is played repeatedly.
Repeat Chapter
” indicator displays on the screen. The
Repeating a Title
2. While the DVD is playing, press the REPEAT DISC button until the “ Repeat Title ” indicator displays on the screen. The
current title is played repeatedly.
To Resume Normal Playback
Playing a Disc
1.
2.
3.
Slide the STANDBY / ON switch on the top of the unit to the ON position.
See CUSTOMIZING THE FUNCTION SETTINGS before proceeding to step 2.
Press the button to open the front panel, press the inside disc switch to open the disc door.
Hold the disc by its sides and carefully place it onto the spindle with the label side facing up, pushing gently until you hear
a “click”.
4. Gently push the disc door closed. It takes a short while for your unit to load the disc. After loading, for most DVDs, the unit
will automatically start playing or take you to the main menu.
5. If the unit does not automatically start playing the DVD, press the  PLAY button.
3. While the DVD is playing, press the REPEAT DISC button until the “ Repeat Off ” indicator displays on the screen.
Repeating a Single Track
1. While the CD disc is playing, press the REPEAT DISC button until the “ Repeat single ” indicator displays on the screen. The
current track is played repeatedly.
Repeating a Whole Disc
2. While the CD disc is playing, press the REPEAT DISC button until the “
whole disc is played repeatedly.
Repeat all
” indicator displays on the screen. The
To Resume Normal Playback
3. Press the REPEAT DISC button until the “ Repeat off ” indicator displays on the screen.
Press here to open
Repeating a Specific Section
You can play a specific section repeatedly.
1. While the disc is playing, press the REPEAT A-B button at the beginning of the section (“ Rep A- ” is displayed) you want to
play repeatedly.
2. Press the REPEAT A-B button again at the end of the section (“ Rep A-B ” is displayed).
3. The Unit will immediately begin replaying your selection.
Pausing Playback (Still Mode)
To Resume Normal Playback
Press the PAUSE button. To resume normal playback, press the PLAY button.
Each time you press the PAUSE button, the picture advances one frame on a DVD.
Stopping Playback
Press the STOP button at the location where you want to interrupt playback. To resume playback at the position where the
disc was stopped, press the PLAY button.
If you press the STOP button twice, the unit’s memory will be cleared and pressing the
PLAY button will reset the disc to
the beginning.
4. While the disc is playing, press the REPEAT A-B button until the “ RepAB Off ” indicator displays on the screen.
Notes:
• Some discs may not permit A-B repeat operation.
• You can not set the A-B repeat function for a segment that includes multiple camera angles.
• You can specify a segment only within the current title or track.
• There may be a slight difference between point A and the location where playback actually resumes depending on the disc.
1. Press the SEARCH
or
SEARCH button when a disc is playing. Each time you press the SEARCH
SEARCH button, the playback speed changes in the following sequence:
x2
x4
x8
x 16
x2
x4
x8
or
x 16
2. Press the PLAY button when you reach the desired point to resume normal playback.
Notes:
• The DVD player mutes sound and subtitles during reverse and forward scan of DVDs.
• The fast playback speed may differ depending on the disc.
Locating a Specific Title
DVD
If a DVD contains title numbers, you can locate a specific title by directly selecting its title number.
1. Press the GOTO button.
Title
2. Press the corresponding number button(s) for the title you want.
3. Press the ENTER button to confirm. Playback starts from the selected section.
Locating a Specific Chapter
---
• Press the
NEXT button to advance chapters/tracks.
• Press the
PREV button to go back to current or previous chapters/tracks.
• For Audio CDs, use the number buttons on the remote control to jump directly to the desired track.
Audio Selection
Locating a Specific Time
On some DVDs, the sound is recorded in two or more formats. Follow the directions below to select the preferred language
and sound system.
1. While a disc is playing, press the AUDIO button to show the current audio format number.
2. Press the AUDIO button repeatedly to select the desired audio format.
Notes:
• If only one audio format is recorded on the DVD, the number does not change.
• Some DVDs allow you to change audio selections via the disc menu only. If this is the case, press the MENU button and
choose the appropriate language on the disc menu.
• You can select different audio channels (Stereo, Left or Right) on an Audio CD by pressing the AUDIO button repeatedly.
Subtitle selection
DVD
1. While a DVD is playing, press the SUBTITLE button to display the current language setting, as shown in
1/4
the example.
2. Press the SUBTITLE button repeatedly to select the desired subtitle language. You can turn subtitles off by pressing the
SUBTITLE button repeatedly until “
Off ” is displayed.
Notes:
• Some DVDs are set to display subtitles automatically, and you cannot turn them off even if you set the subtitle function to
off.
• During some scenes, the subtitles may not appear immediately after you select your desired scene.
• The number of subtitle languages recorded differs depending on the disc. If only one language is recorded, the language
does not change.
• This function can only be used for discs on which subtitles have been recorded in multiple languages.
• Some DVDs allow you to change subtitles via the disc menu only. If this is the case, press the MENU button and choose the
appropriate subtitle on the disc menu.
Angle selection
DVD
Some DVDs contain scenes which have been shot from a number of different angles. For these discs, the same scene can be
viewed from each of these different angles.
1. While you are playing a DVD with different angles recorded, press the
ANGLE button to view the number of current angles available.
2. Press the ANGLE button repeatedly to change the scene to the next
recorded angle.
• After approx. two seconds, playback will continue from the new angle
selected.
• If no button is pressed within 10 seconds, playback continues without
changing the current angle.
1/3
Sequence of angle shots
(Example)
Notes:
• This function can only be used for discs on which scenes shot from multiple angles have been recorded.
• If only one angle is recorded, “
1/1 ” is displayed.
Display function
While the disc is playing, press the DISPLAY button repeatedly to display information
on operation status.
Elapsed Time
00:05:18
Remain Time
00:30:28
Elapsed Time: Elapsed time from the beginning of the title which is currently playing.
Title 1/3
Remain Time: Remaining time of the title which is currently playing.
Audio
Chapter 1/5
Subtitle 1/4 Eng
Adjust the LCD Screen
DVD
You can adjust the Brigntness, Contrast, Color or View Mode of the LCD screen.
1. Press the VIDEO MODE button.
2. Press the / button to select Brightness, Contrast, Color or View Mode.
3. Then press the / button to change the setting.
(For View Mode, press the ENTER button to change the setting.)
4. Press the VIDEO MODE button to exit the menu.
E-7
PVS72830 IB UL English RCA W011.indd 2
Angle 1/3
--:--:--
Notes:
• If the numbers you entered is not permited by the DVD, after you press the ENTER button, it will restore to “- - -”. You
should re-enter correct numbers.
• Some discs may not respond to this process.
• Some scenes may not be located as precisely as you specified.
• This method for accessing specific locations is available only within the current title of the DVD.
DVD PROGRAMMABLE MEMORY
Language
You can combine your favorite titles/chapters and play them in the order you determine.
1. When a DVD is stopped, press the MEMORY button, the right display appears.
2. Select the items in the order you want by pressing the number buttons.
Each time you press the Cursor buttons ( , , , ), the space is highlighted. Highlight
where you want to enter, then press the corresponding number buttons.
3. Press the Cursor buttons ( , , , ) to move the highlighted bar to Play Memory, then
Title Chapter
press the ENTER button.
The DVD player starts memory playback.
4. To resume normal playback from memory playback
1). When a DVD is stopped, press the MEMORY button.
2). Press the Cursor buttons ( , , , ) to move the highlighted bar to “Clear All”, then press the ENTER button. All the
input programs will be cleared.
3). Press the PLAY button to resume normal playback.
Notes:
• If the title or chapter numbers you entered is not permited by the DVD, after you press the ENTER button, it will restore to “- -”. You should re-enter the correct numbers.
• Some discs may not permit memory playback operation.
• If you select repeat during memory playback, the DVD player repeats the current memory playback.
• If you press the MEMORY button while the display appears on the TV screen, the display disappears.
• The programmed selections will be cleared when you open the disc tray or turn off the DVD player.
This unit can play JPG files recorded on a CD-R or CD-ROM disc (CD-RW is not recommended).
Viewing JPG Files
user manual
DRC97283
1. Press the SETUP button in stop mode.
2. Press the / button to select Misc.
3. Press the button, then press the / button to select Use Default
Settings dialogue box.
4. Press the ENTER followed by the / button to select “Yes”, then press
the ENTER button. The original setting will be restored. The unit will exit
the menu automatically and re-load the disc in the disc tray.
Note: It will take 3-5 seconds to reset the DVD player to the factory default.
Screen Saver
1.
2.
3.
4.
Press the SETUP button in stop mode.
Press the / button to select Misc.
Press the button, then press the / button to select Screen Saver.
Press the ENTER button, then press the / button to change the On/
Off mode.
5. Press the ENTER button.
6. Press the SETUP or RETURN button to exit the menu.
AVC Multimedia
Markham, Ontario L3R 1E3
http: //www.RCAav.com
Read these instructions before using your new product for the first time.
Safety Precautions
MAINTENANCE
Cleaning the Disc
A defective or soiled disc inserted into the unit can cause sound to drop out during playback.
Handle the disc by holding its inner and outer edges.
• Do NOT touch the surface of the unlabeled side of the disc.
• Do NOT stick paper or tape on the surface.
• Do NOT expose the disc to direct sunlight or excessive heat.
• Clean the disc before playback. Wipe the disc from the center outward with a cleaning cloth.
• NEVER use solvents such as benzine or alcohol to clean the disc.
• Do NOT use irregular shaped discs (example: heart shaped, octagonal, etc.). They may cause malfunctions.
Cleaning the Unit
1. Press the SETUP button in stop mode.
2. Press the button to select OSD Language.
3. Press the ENTER button, then the / button to shift and change the
Language.
4. Press the ENTER button.
5. Press the SETUP or RETURN button to exit the menu.
The lightning flash with an arrowhead symbol, within the
equilateral triangle, is intended to alert the user to the
presence of uninsulated "dangerous voltage" within the
product's enclosure that may be of sufficient magnitude
to cause an electric shock.
• Be sure to turn the unit off and disconnect the AC power adapter before maintaining the unit.
• Wipe the unit with a dry soft cloth. If the surfaces are extremely dirty, wipe clean with a cloth that has been dipped in a
weak soap-and-water solution and wrung out thoroughly, then wipe with a dry cloth.
• Never use alcohol, benzine, thinner, cleaning fluid or other chemicals. Do NOT use compressed air to remove dust.
Important Note
The exclamation point within the equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in this
owner’s manual.
• Before transporting the unit, remove any disc from the disc compartment.
1. Press the SETUP button in stop mode.
2. Press the button, then the / button to select Subtitle.
3. Press the ENTER button, then the / button to shift and change the
Language.
4. Press the ENTER button.
5. Press the SETUP or RETURN button to exit the menu.
Notes:
• Some DVDs are programmed with a specific language. You may not be
able to change this feature.
• Some DVDs allow you to change subtitle selections via the disc menu
only. If this is the case, press the MENU button and choose the appropriate subtitle language from the selection on the
disc menu.
Audio
1. Press the SETUP button in stop mode.
2. Press the button, then the / button to select Audio.
3. Press the ENTER button, then the / button until your preferred Audio
is displayed.
4. Press the ENTER button.
5. Press the SETUP or RETURN button to exit the menu.
Note: Some DVDs are programmed with a specific language. You may not be
able to change this feature.
TROUBLESHOOTING GUIDE
SYMPTOM
This product
contains a low
power laser device.
No power.
• Ensure the AC power adapter is connected.
• The unit is not turned on.
The remote control does • not function.
•
•
•
•
WARNING: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE COVER (OR
BACK). NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
WARNING: TO PREVENT FIRE OR SHOCK
HAZARD, DO NOT EXPOSE THIS APPLIANCE TO
RAIN OR MOISTURE. DO NOT PLACE OBJECTS
FILLED WITH LIQUIDS ON OR NEAR THIS UNIT.
CAUTION: Use of controls or adjustments
or performance of procedures other
than those specified may result in
hazardous radiation exposure.
CAUTION: DANGER OF EXPLOSION IF BATTERY
IS INCORRECTLY REPLACED. REPLACE ONLY
WITH THE SAME OR EQUIVALENT TYPE.
CAUTION
INVISIBLE LASER RADIATION WHEN
OPEN.
AVOID EXPOSURE TO BEAM.
THIS CLASS B DIGITAL APPARATUS COMPLIES
WITH CANADIAN ICES-003.
On Placement
Make sure the infrared remote sensor is not blocked.
Make sure the plastic sheet has been removed from the remote control.
Point the remote directly at the infrared remote sensor on the unit.
Replace the battery in the remote control with a new one.
Use remote control with GREEN keys with the unit which has GREEN mark.
Use remote control with BLUE keys with the unit which has BLUE mark.
No sound or only a very • low-level sound is heard. •
•
•
Make sure ON mode was selected.
The volume control is located on the side of the unit – please try adjusting this.
The system is in pause mode. Press the PLAY button to return to normal play mode.
The unit is in fast-forward or fast-reverse mode. Press the
PLAY button to return to normal
play mode.
• Make sure the AUDIO/VIDEO output connections are correct.
• The DTS DVD cannot be decoded to have speaker output.
• The unit is too hot; shut off the unit for 30 minutes to cool it down.
1. Press the SETUP button in stop mode.
2. Press the button, then the / button to select DVD Menu.
3. Press the ENTER button, then the / button until your preferred DVD
Menu language is displayed.
4. Press the ENTER button.
5. Press the SETUP or RETURN button to exit the menu.
Note: Some DVDs are programmed with a specific language. You may not be
able to change this feature.
Video
Aspect Ratio
* SEE BOTTOM OF UNIT FOR GRAPHIC SYMBOLS *
CAUSE (AND REMEDY)
DVD Menu
Playing Titles/Chapters in a Favorite Order
VIEWING JPG FILES
Sequence of display (Example)
DVD
You can move to a specific location by entering its corresponding time (hours, minutes, seconds).
1. Press the GOTO button.
Time
2. Press or button to display Time and press the corresponding number buttons for
the setting point you want.
3. Press the ENTER button to confirm. Playback starts from the selected section.
CUSTOMIZING THE FUNCTION SETTINGS
Subtitle
DVD
If you know the chapter number for the chapter that you want to play, you can locate it by directly selecting that number.
1. Press the GOTO button.
Chapter
--2. Press
or
button to display Chapter and press the corresponding number
button(s) for the chapter you want.
3. Press the ENTER button to confirm. Playback starts from the selected section.
Skip (Forward / Reverse)
When play CD / JPG discs, you can modify the Play Modes through the Toolkit which appears on the right of below picture on
the screen. Press the / button to navigate between the windows and the / button to select files/tracks or play mode
items. Then press the ENTER button.
1. In Stop mode, press the Cursor buttons ( , , , ) to select "Edit mode" then press the ENTER button.
2. Use the Cursor buttons ( , , , ) to select tracks/files shown on the left hand side of the window. Press the ENTER
button to confirm the selected tracks/files. " " will appear in front of the selected tracks/files.
3. Select "Add to program" then press the ENTER button. " " will disappear from the screen. It means that the tracks/files
you have selected are added into the "Program view".
4. Select "Program view" to view programmed files. To add more files by "Browser view" repeat the above steps.
5. Press the PLAY button to start the program playback.
The Toolkit has the following play mode items:
• Repeat (Off/Single/All):
Off: Resumes normal playback.
Single: Repeats the current track/file.
All: Repeats all files on the current folder or all tracks on the disc.
• Mode (Normal / Shuffle / Music intro):
Normal: Resumes normal playback.
Shuffle: Playbacks track/file in random order.
Music intro (for Audio CD only): Only playbacks the first 10 seconds of all the
tracks on the current folder/disc.
• Edit mode: Program operation works only when "Edit mode" is selected.
• Program view: To view tracks/files in the "Program view" list. It is disabled when the "Program view" list is empty.
• Add to program: Add files/tracks to the "Program view" list. It is disabled if the "Edit mode" is not selected.
• Browser view: To view files/tracks in the original view list.
• Clear program: Delete the files/tracks in the "Program view" list.
Select a file/track or more you want to delete in complete stop mode (press the STOP button twice). "
" will appear
besides the deleted file/track. Select "Clear program" and then press the ENTER button. It is disabled if the "Edit mode" is
not selected.
Note:
The program will be deleted if disc door is opened or selected files are deleted by selecting "Clear program" in "Edit mode".
OSD Language
locating a desired section
Fast Forward / Fast Reverse
Misc
Use Default Settings
PLAY ModeS for CD or JPG Disc
REPEAT PLAYBACK
Basic playback
• Do not use the unit in places that are extremely hot, cold, dusty or humid.
• Place the unit on a flat and even surface.
• Do not restrict the air flow of the unit by placing it in a place with poor air flow, by covering it with a cloth, or by
placing it on carpeting.
• To avoid magnetized, do not place the unit near speaker or magnet.
• Do not use this unit in direct sunlight or leave the unit in a closed automobile (or yacht, etc) where it would be
exposed to high temperatures above 104°F (40°C).
• No naked flame sources such as lighted candles should be placed on the AC power adapter and main unit.
• The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases,
shall be placed on apparatus.
On Safety
• When connecting or disconnecting the AC power adapter, grip the plug and not the cord itself. Pulling the cord
may damage it and create a hazard.
• When you are not going to use the unit for a long period of time, disconnect the AC power adapter.
On Condensation
• When left in a heated room where it is warm and damp, water droplets or condensation may form inside the unit.
When there is condensation inside the unit, the unit may not function normally. Let the unit stand for 1 to 2 hours
before turning the power on, or gradually heat the room and allow the unit to dry before use.
No picture
• The region number of the disc doesn't match the region number of this unit.
The picture is not clear
• Clean the disc.
• The disc is scratched.
• Adjust the LCD's brightness, contrast and color using the VIDEO MODE button on the remote
control.
Severe hum or noise is
heard.
• The plugs and jacks are dirty. Wipe them with a cloth slightly moistened with alcohol.
• Clean the disc.
The disc does not play.
•
•
•
•
•
The picture is up-sidedown
• Press the
Ventilation Warning
Aspect Ratio
1.
2.
3.
4.
Press the SETUP button in stop mode.
Press the / button to select Video.
Press the button, then the / button to select Aspect Ratio.
Press the ENTER button, then the / button to shift and change the
aspect ratio.
5. Press the ENTER button.
6. Press the SETUP or RETURN button to exit the menu.
Notes:
• The displayable picture size is preset on the DVD. Therefore, the playback picture of some DVDs may not conform to the
picture size selected.
• When you play DVDs recorded in the 4:3 picture size only, the playback picture always appears in the 4:3 picture size
regardless of the Aspect Ratio setting.
• Select 16:9 to conform to the LCD screen on the unit. Always be sure that your Aspect Ratio conforms to the actual TV in
use if you connect the unit to a TV.
1. Press the button to open the front panel, press the inside disc switch to open
the disc door.
2. Hold the disc by its edges and gently push it onto the spindle with label side
facing towards you until you hear a “click”.
3. Close the disc door. A list of folders/files will appear on the screen.
4. Press the or button to select your desired file. The selected picture will
appear in the lower right corner. Press the
PLAY button to start playback.
Press the STOP button to display a folder list.
Notes:
• You can press the PAUSE button to freeze the picture, and press the PLAY button to resume slide show.
• You can press the STOP button to quit playback.
• You can press the
PREV or
NEXT button to change the picture. Press the
PREV button to view the previous
picture. Press the
NEXT button to view the next picture.
• You can press the ANGLE buttonon on the remote control to rotate the direction of the picture by 90o.
• Some discs may not permit this operation.
Press the SETUP button in stop mode.
Press the / button to select Video.
Press the button, then the / button to select View Mode.
Press the ENTER button, then the / button to shift and change the
View Mode.
5. Press the ENTER button.
6. Press the SETUP or RETURN button to exit the menu.
Fill
Fill the screen with decoded image.
Original
Display image as its original size.
Auto Fit
Automatically fit the decoded image on screen without
distortion. Black bars will be present on top/bottom or left/right of screen.
Pan Scan
Select when a standard 4:3 TV is connected. Displays pictures cropped to fill your TV screen. Sides of the picture
are cut off.
Note: Depending on the DVD, you may not be able to view the mode as selected.
E-8
E-9
There is no disc inside (“No Disc” appears on the screen).
Insert the disc correctly with the playback side facing down.
Clean the disc.
A non-NTSC disc has been inserted. The unit and disc region number are incompatible.
Condensation may have formed inside the unit due to a sudden change in temperature. Wait
about an hour for it to clear and try again.
button located on front of player.
Specifications and external appearance are subject to change without notice.
• Do not block the ventilation openings or holes. (If the ventilation openings or holes are blocked by a newspaper
or cloth, etc., the heat may not be able to get out.)
• Do not operate the unit in a confined space, such as a bookcase or built-in cabinet, allow about 4 inch (10cm) of
free space all around the unit for adequate ventilation.
Rating Plate Location
• The rating plate is located on the bottom of unit.
FCC Statements
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
View Mode
1.
2.
3.
4.
WARNING: Should any trouble occur, disconnect the AC power adapter and refer servicing to a qualified
technician.
Notes on Copyright
It is forbidden by law to copy, broadcast, show, broadcast on cable, play in public, or rent copyrighted material
without permission.
Apparatus Claims of U.S. Patent Nos. 6,836,549; 6,381,747; 7,050,698; 6,516,132 and 5,583,936 licensed for limited
viewing uses only.
This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual
property rights. Use of this copyright protection technology must be authorized by Macrovision, and is intended
for home and other limited viewing uses only unless otherwise authorized by Macrovision. Reverse engineering or
disassembly is prohibited.
Need More Help?
Please visit online help at
http://www.RCAav.com
DO NOT RETURN THIS PRODUCT TO THE STORE
Printed in China
811-728391W011
E-1
2010-2-2 17:47:30
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement