SD-K741SU DVD VIDEO PLAYER TOSHIBA

SD-K741SU DVD  VIDEO  PLAYER TOSHIBA
TOSHIBA
DVD VIDEO PLAYER
SD-K741SU
OWNER’S MANUAL
C 2004 Toshiba Corporation
Introduction
2
Connections
18
Basic playback
24
Advanced playback
32
Function setup
56
Others
64
Introduction
SAFETY PRECAUTIONS
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
AVIS
!
RISQUE DE CHOC ELECTRIQUE NE
PAS OUVRIR
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USERSERVICEABLE PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
CAUTION: (Visible) Laser Radiation When Open.
DO NOT STARE INTO BEAM.
The lightning flash with arrowhead symbol, within an
equlateral triangle, is intended to alert the user to the
presence of uninsulated “dangerous voltage “within the
product’s enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the
literature accompanying the appliance.
The symbol for CLASS II (Double Insulation)
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE. DANGEROUS HIGH VOLTAGE ARE PRESENT
INSIDE THE ENCLOSURE. DO NOT OPEN THE CABINET. REFER SERVICING TO
QUALIFIED PERSONNEL ONLY.
CAUTION:
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY
INSERT.
CAUTION:
This Digital Video Disc Player employs a Laser System.
To ensure proper use of this product, please read this owner’s manual carefully and retain for
future reference. Should the unit require maintenance, contact an authorized service location.
Use of controls or adjustments or performance of procedures other than those specified herein
may result in hazardous radiation exposure.
To prevent direct exposure to laser beam, do not try to open the enclosure.
Visible and invisible laser radiation when open and interlocks defeated.
DO NOT STARE INTO BEAM.
FCC NOTICE: This equipment has been tested and found to comply with the limits for Class B digital device,
pursuant to part 15 of the FCC Rule. These limits are designed to provide reasonable protection
against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that of which the receiver is
connected.
- Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications made to this equipment, not expressly approved by Toshiba, or
parties authorized by Toshiba, could void the user’s authority to operate the equipment.
2
The instructions shall state that an ALL-POLE MAINS SWITCH with a contact separation of at least 3 mm in
each pole shall be incorporated in the electrical installation of the building.
These servicing instructions are for use by qualified service personnel only. To reduce the
risk of electric shock do not perform any servicing other than that contained in the operating
instructions unless you are qualified to do so.
In the spaces provided below, record the Model and Serial No. Located on the rear panel of your DVD video
player.
Model No.
Introduction
CAUTION:
Serial No.
Retain this information for future reference.
Location of the required label
THIS PRODUCT COMPLIES WITH DHHS RULE 21 SUBCHAPTER J PARTS
1040-10 AND 1040-11 AT DATE OF MANUFACTURED .
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION
IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY
NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT
MAY CAUSE UNDESIRED OPERATION.
MANUFACTURED
TOSHIBA CORPORATION
1-1, SHIBAURA 1-CHOME, MINATO-KU,
TOKYO 105-8001, JAPAN
SERIAL NO.
Be aware that this equipment is still powered even after the ON/STANDBY indicator turns off (standby mode)
by pressing the ON/STANDBY button. To disconnect this equipment completely from the main power, pull out
the power plug from the wall outlet.
3
Introduction
IMPORTANT SAFETY INSTRUCTIONS
CAUTION: PLEASE READ AND OBSERVE ALL WARNINGS AND INSTRUCTIONS GIVEN IN THIS
OWNER’S MANUAL AND THOSE MARKED ON THE UNIT. RETAIN THIS BOOKLET
FOR FUTURE REFERENCE.
This set has been designed and manufactured to assure personal safety. Improper use can result in
electric shock or fire hazard. The safeguards incorporated in this unit will protect you if you observe the following procedures for installation, use and servicing. This unit is fully transistorized and does not contain
any parts that can be repaired by the user.
DO NOT REMOVE THE CABINET COVER, OR YOU MAY BE EXPOSED TO DANGEROUS VOLTAGE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL ONLY.
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
4
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instruction.
Introduction
8. Do not install near any heat sources such as radiators, heat registers, stove, or other apparatus
(including amplifiers) that produce heat .
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding type plug has two blades and a third grounding
prong. The wide blade or the third prong are provided for your safety. If the provided plug does not
fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination to avoid injury from tip-over.
5
Introduction
IMPORTANT SAFETY INSTRUCTIONS
13. Unplug this apparatus during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not
operate normally, or has been dropped.
ADDITIONAL SAFETY INSTRUCTIONS
15. When you use headphones, keep the volume at a moderate level. If you use the headphones continuously with high volume sound, it may cause hearing damage.
16. Do not overload wall outlets; extension cords, or integral convenience receptacles as this can result
in a risk of fire or electric shock.
17. The apparatus shall not be exposed to dripping or splashing liquids. Do not place objects such as
vases filled with liquid on top of the apparatus.
6
18. Keep your fingers well clear of the disc tray as it is closing. Neglecting to do so may cause serious
personal injury.
Introduction
19. Do not place a heavy object on or step on the apparatus. The object may fall, causing serious personal injury and serious damage to the apparatus.
20. Do not use a cracked, deformed, or repaired disc. These discs are easily broken and may cause serious personal injury and apparatus malfunction.
21. If the apparatus should smoke or smell, immediately disconnect the power cord from the wall outlet.
Wait until the smoke or smell stops, then ask your dealer for a check and repair. Neglecting to do so
may cause fire.
22. While it is thundering, do not touch the connecting cables or the apparatus.
23. The apparatus includes lead, an ingredient of solder used on the PCB, which is a harmful substance
to human and the environment. When disposing of this apparatus, follow the rules and regulations in
your area.
7
Introduction
Precautions
Notes on handling
■ When shipping the DVD video player, the original
shipping carton and packing materials come in handy.
For maximum protection, repack the units as it was
originally packed at the factory. Take care not to give
it a shock or shake when carrying.
■ Do not use volatile liquids, such as insect spray, near
the DVD video player. Do not leave rubber or plastic
products in contact with the DVD video player for a
long time. They will leave marks on the finish.
■ The top and rear panels of the DVD video player may
become warm after a long period of use. This is not a
malfunction.
■ When the DVD video player is not in use, be sure to
remove the disc and turn off the power.
■ If you do not use the DVD video player for a long period,
the unit may not function properly in the future. Turn on
and use the DVD video player occasionally.
Notes on locating
■ Place the DVD video player on a level surface. Do
not use it on a shaky or unstable surface such as a
wobbling table or inclined stand. The loaded disc may
come off the proper position and cause damage to
the DVD video player.
■ When you place this DVD video player near a TV,
radio, or VCR, the playback picture may become poor
and the sound may be distorted. In this case, place
the DVD video player away from the TV, radio, or
VCR.
Notes on moisture condensation
Moisture condensation damages the DVD video
player. Please read the following carefully.
Moisture condensation occurs, for example, when you
pour a cold drink into a glass on a warm day. Drops of
water form on the outside of the glass. In the same way,
moisture may condense on the optical pick-up lens inside
this unit, one of the most crucial internal parts of the DVD
video player.
■ Moisture condensation occurs during the following
cases.
● When you bring the DVD video player directly from a cold
place to a warm place.
● When you use the DVD video player in a room where you
just turned on the heater, or a place where the cold wind
from the air conditioner directly hits the unit.
● In summer, when you use the DVD video player in a hot
and humid place just after you move the unit from an air
conditioned room.
● When you use the DVD video player in a humid place.
Notes on cleaning
Use a soft, dry cloth for cleaning
● For stubborn dirt, soak the cloth in a weak detergent
solution, wring well and wipe. Use a dry cloth to wipe
it dry.
Do not use any type of solvent, such as thinner and
benzine, as they may damage the surface of the DVD
video player.
● If you use a chemical saturated cloth to clean the unit,
follow that product’s instructions.
8
Where
■ Do not use the DVD video player where moisture
condensation may occur.
If you use the DVD video player in such a situation, it
may damage discs and internal parts. Remove the disc,
connect the power cord of the DVD video player to the
wall outlet, turn on the DVD video player, and leave
it for two or three hours. After two or three hours, the
DVD video player will have warmed up and the moisture
condensation may evaporate.
Notes on discs
Do not touch the playback side of the disc.
●
Playback side
Normally, DVD video discs are divided into titles, and
the titles are sub-divided into chapters. VIDEO CDs,
and audio CDs are divided into tracks.
Introduction
Structure of disc contents
On handling discs
DVD video disc
YES
DVD Video disc
Playback side
Title 1
Chapter 1 Chapter 2 Chapter 1
Title 2
Chapter 2
Chapter 3
C
● Do not attach paper or tape to discs.
VIDEO CD/audio CD
NO
Track 1
VIDEO CD/audio CD
Track 2
Track 3
Track 4
Track 5
On cleaning discs
●
Fingerprints and dust on the disc cause picture
and sound deterioration. Wipe the disc from the
center outwards with a soft cloth. Always keep
the disc clean.
YES
NO
Each title, chapter or track is assigned a number, which
is called "title number", "chapter number" or "track
number" respectively.
There may be discs that do not have these numbers.
Notes on copyright
It is forbidden by law to copy, broadcast, show,
broadcast on cable, play in public, and rent copyrighted
material without permission.
●
Do not use any type of solvent such as thinner,
benzine, commercially available cleaners or
antistatic spray for vinyl LPs. It may damage the
disc.
On storing discs
●
●
●
Do not store discs in a place subject to direct
sunlight or near heat sources.
Do not store discs in places subject to moisture
and dust such as a bathroom or near a humidifier.
Store discs vertically in a case. Stacking or placing objects on discs outside their case may cause
warping.
DVD video discs are copy protected, and any recordings made from these discs will be distorted.
This product incorporates copyright protection technology that is protected by method claims of certain U.S.
patents and other intellectual property rights owned
by Macrovision Corporation and other rights owners.
Use of this copyright protection technology must be
authorized by Macrovision Corporation, and is intended
for home and other limited viewing uses only unless
otherwise authorized by Macrovision Corporation.
Reverse engineering or disassembly is prohibited.
9
Introduction
Notes on discs (continued
(continued)
About this owner’s manual
This owner’s manual explains the basic instructions
of this DVD video player. Some DVD video discs are
produced in a manner that allows specific or limited operation during playback. As such, the DVD video player
may not respond to all operating commands. This is not
a defect in the DVD video player. Refer to instruction
notes of discs.
" " may appear on the TV screen during operation.
A " " means that the operation is not permitted by the
DVD video player or the disc.
Playable discsl
This DVD video player can play the following discs.
Disc Mark
Contains
Disc Size
Maximum
playback time
Approx. 4 hours
(single sided disc)
12 cm
DVD
video
discs
Audio
+
Video
(movinges)
Video
CDs
Audio
+
Video
(moving
pictures)
8 cm
Approx. 8 hours
(double sided disc)
Approx. 80 minutes
(single sided disc)
Approx. 160 minutes
(single sided disc)
Notes on region numbers
The region number of this DVD video player is 1. If
region numbers, which stand for their playable area, are
printed on your DVD video disc and you do not find
or
, disc playback will not be allowed by the player.
(In this case, the DVD video player will display a message on-screen.)
Notes On VIDEO CDs
This DVD video player supports VIDEO CDs
equipped with the PBC (Version 2.0) function. (PBC
is the abbreviation of playback Control.) You can
enjoy two playback variations depending on types
of discs.
● VIDEO CD not equipped with PBC function
(Version 1.1)
Sound and movie can be played on this DVD
video player in the same way as an audio CD.
● VIDEO CD equipped with PBC function (Version
2.0)
In addition to operation of a VIDEO CD not
equipped with the PBC function, you can enjoy
playback of interactive software with search
function by using the menu displayed on the TV
screen (Menu playback).
Some of the functions described in this owner’s
manual may not work with some discs.
10
Audio
CDs
12 cm
Approx. 74 minutes
8 cm
(CD single)
Approx. 20 minutes
12 cm
Approx. 74 minutes
8 cm
(CD single)
Approx. 20 minutes
Audio
The following discs are also available.
● DVD-R discs of DVD video format
● CD-R/CD-RW discs of CD-DA format
Some of these discs may be incompatible.
● You cannot play discs other than those listed above.
● You cannot play DVD-RAM discs or non-standardized discs,
etc., even if they may be labeled as above.
● This DVD video player uses the NTSC color system, and cannot play DVD video discs recorded in any other color system
(PAL, SECAM, etc.).
Because of problems and errors that can occur during the
creation of DVD software and/or the manufacture of DVD discs,
Toshiba America Consumer Products, L.L.C., Toshiba Hawaii,
Inc. and Toshiba of Canada, Ltd. cannot guarantee that this
player will play every feature of every DVD bearing the DVD
logo. As one of the creators of DVD technology, Toshiba DVD
players are manufactured to the highest standards of quality
and, as a result, such incompatibilities are very rare. If you
happen to experience and difficulty playing a DVD on a Toshiba
DVD player, please feel free to call our Contact listed in "LIMITED UNITED STATES WARRANTY DVD PLAYERS" 66 .
Table of Contents
Advanced playback
●SAFETY PRECAUTIONS............................2
●IMPORTANT SAFETY INSTRUCTIONS.....4
●Precautions................................................8
●Notes on Discs ...........................................9
Notes on region numbers...........................10
●Table of Contents.......................................11
●Identifications of controls.........................12
Front panel ................................................12
Rear panel..................................................13
Remote control ...........................................14
Loading batteries........................................15
Operating with the remote control ............15
Connections
●Connecting to a TV...................................18
Connecting to a TV ..................................18
Connecting to an audio system and TV
equipped with component video inputs......19
●Connecting to Optional Equipment........20
Connecting to an amplifier equipped with
a Dolby Digital decoder..............................21
Connecting to an amplifier equipped with
a Dolby Surround Pro Logic.......................21
Connecting to an amplifier equipped with
a DTS decoder .........................................22
Connecting to an amplifier equipped with
a digital audio input....................................22
Basic playback
●Playing a Disc
Basic playback...........................................24
●Variable Speed Playback .........................26
Playing in fast reverse or fast forward
directions..................................................26
Playing frame by frame..............................26
Playing in slow-motion ..............................27
Resume playback from the same location...27
●Locating a Desired Section......................28
Locating a title using the top menu...........28
Locating a desired section by entering the
corresponding number..............................29
Locating a specific chapter or track...........29
.
●Accessing a Specific Location Directly...32
Entering the time counter of the desired
location......................................................32
Setting a bookmark...................................32
●Repeating a Specific Segment ................33
Repeating a specific segment...................33
●Playing in a Varied Order.........................34
Playing titles, chapters or track in a varied
order..........................................................34
●Playing in a Favorite Order......................35
Setting titles, chapters or tracks in a
favorite order..............................................35
●Zooming a picture......................................36
zooming a picture .......................................36
●Selecting the Picture Enhancement
(E.P.M.)......................................................37
Selecting the picture enhancement ..........37
●Selecting the Sound Enhancement
(E.A.M.)......................................................38
Selecting the sound enhancement ...........38
●Selecting the Camera Angle ....................39
Changing the camera angle.......................39
●Selecting Subtitles....................................40
Selecting a subtitle language.....................40
●Selecting a Language ................................41
Selecting a playback audio setting............41
●On-screen display operation....................43
On-screen display operation......................43
●Playing MP3/WMA Files............................46
Playing MP3/WMA Files............................46
●Viewing JPEG Files...................................48
Starting a slide show........................................48
Starting from a thumbnail view or a folder list....50
Viewing a single image..............................51
Introduction
Introduction
Function setup
●Customizing the Function Settings ........56
Setting procedure.......................................56
Setting details............................................58
●Table of Languages..................................62
Others
●Before Calling Service Personnel...........64
●Specifications...........................................65
●LIMITED UNITED STATES WARRANTY
DVD PLAYERS............................................66
11
Introduction
Identification of Controls
See the page in
for details.
Front panel
ON/STANDBY indicator
ON: Lit in green
Standby mode: Not lit
Disc tray
DVD display
Remote Sensor
24
24
SKI P
P AU SE
OPEN/CLOSE button 24
SKIP button 29
PAUSE button
S TO P
PL AY
26
STOP button
12
15
PLAY button
O PE N/ CLO SE
VO O N/ ST A ND BY
ON/STANDBY button
24
27
24
VIDEO OUT jack
18
VIDEO OUT (Y/PB/PR)
(Component video) jacks
Introduction
Rear panel
19
Power cord
BITSTREAM/PCM DIGITAL COAXIAL
AUDIO OUT jack 21 22
ANALOG AUDIO OUT (L/R) jacks
S VIDEO OUT jack
18
19
18
13
Introduction
Identification of Controls (continued)
The instructions in this manual describe the functions on the remote control. See the page in
for details
Remote control
OPEN/CLOSE button
SKIP buttons 29
24
ON/STANDBY button
REV button 26
FWD button
SUBTITLE button
ANGLE button
AUDIO button 41
STOP button 25
ENTER button
MENU button*
28
DIRECTION buttons
45
24
E.A.M. button
28
ZOOM button
36
SLOW button
27
19
29
32
56
MEMORY button
26
28
T button
SETUP button
25
E.P.M. button 37
PROGRESSIVE button
38
Number buttons
56
PLAY button 24
PAUSE/STEP button
TOP MENU button
PBC button
29
RETURN button
39
NAVI button 43
DISPLAY button
26
CLEAR button
40
24
35
A-B RPT button 33
PLAY MODE button
34
* MENU button
Use the MENU button to display the menu included on many DVD video disc. To operate a
menu, follow the instructions in "Locating a title
using the top menu." 28
14
1
Open the cover.
Operating with the remote control
Point the remote control at the remote
sensor and press the buttons.
VO O N/ ST A ND BY
2
Distance:
Angle:
3
Close the cover.
Notes on batteries
Improper use of batteries may cause battery leakage
and corrosion. To operate the remote control correctly,
follow the instructions below.
● Do not insert batteries into the remote control in the
wrong direction.
● Do not charge, heat, open, or short-circuit the batteries.
Do not throw batteries into a fire.
● Do not leave dead or exhausted batteries in the
remote control
● Do not use different types of batteries together, or
mix old and new batteries.
● If you do not use the remote control for a long period of time, remove the batteries to avoid possible
damage from battery corrosion.
● If the remote control does not function correctly or if
the operating range becomes reduced, replaced all
batteries with new ones.
● If battery leakage occurs, wipe the battery liquid
from the battery compartment, then insert new batteries.
SKI P
P AU SE
S TO P
PL AY
30°
30°
Within about 7 m(23 feet)
Insert batteries (AAA size).
Make sure to match the + and -on the batteries to
the marks inside the battery compartment.
O PE N/ CLO SE
Introduction
Loading batteries
Maximum of 7 m (23 feet) from the front
of the remote sensor.
Approximately 30° from each direction
of the front of the remote sensor.
* Do not expose the remote sensor of the DVD
video player to a strong light source such as
direct sunlight or other illumination. If you do so,
you may not be able to operate the DVD video
player via the remote control.
Notes on the remote control
● Direct the remote control at the remote sensor of
the DVD video player.
● Do not drop or give the remote control a shock.
● Do not leave the remote control near an extremely
hot or humid place.
● Do not spill water or put anything wet on the remote
control.
● Do not disassemble the remote control.
15
Connections
Read this chapter first to make all necessary
preparations.
●Connecting to a TV
●Connecting to an audio system
and TV equipped with
component video inputs
●Connecting to an amplifier
equipped with a Dolby Digital
decoder
●Connecting to an amplifier
equipped with Dolby Surround
Pro Logic
●Connecting to an amplifier
equipped with a DTS decoder
●Connecting to an amplifier
equipped with a digital audio
input
Connections
Connecting to a TV
Connect the DVD video player to your TV.
For details of output sound, see
ee 42 .
Connecting to a TV
Signal Flow
To S VIDEO
OUT
(yellow)
(red)
(white)
To wall outlet
To VIDEO
OUT
To ANALOG AUDIO OUT
Audio/video cable (supplied)
To video input
(red)
(yellow)
S video cable (not supplied)
To audio inputs
(white)
To S video input
If the TV has an S video input,
connect the DVD video player with
an S video cable. When using an
S video cable, do not connect the
yellow video cable.
TV or monitor with
audio/video inputs
● Making the following setting.
On-screen display
Select:
Page
“Digital Output”
“Bitstream”
or
“PCM”
56
“Video Output”
CVBS
59
60
Notes
● Refer to the owner’s manual of the connected TV as well.
● When you connect the DVD video player to your TV, be sure to turn off the power and unplug both units from the
wall outlet before making any connections.
● If your TV has one audio input, connect the left and right audio outputs of the DVD video player to a Y cable adapter
(not supplied) and then connect to your TV
● connect the DVD player directly to your TV. If you connect the DVD video player to a VCR, TV/VCR combination or
video selector, playback picture may be distorted as DVD video discs are copy protected.
● Analog audio out will not have sound DTS playback.
18
Interlaced outputs/inputs(ColorStream®)
Some TVs or monitors are equipped with component video
inputs. Connecting to these inputs allows you to enjoy
higher quality picture playback.
Actual labels for component video inputs may vary depending
on the TV manufacturer.(ex.Y, R-Y, B-Y or Y, CB, CR)
In some TVs or monitors, the color levels of the playback
picture may be reduced slightly or the tint may change.
In such a case, adjust the TV or monitor for optimum
performance.
Progressive outputs/inputs (ColorStream®Pro)
Some TVs or monitors are equipped with component video
inputs that are capable of reproducing a progressively
scanned video signal. Connecting to these inputs allow you to
view the highest quality picture with less flicker.
Consumers should note that not all high definition television
sets are fully compatible with this product and may cause
artifacts to be displayed in the picture. In case of 480
progressive scan picture problems, it is recommended that the
user switch the connection to the "standard definition" output.
If there are questions regarding our TV set compatibility with
this model 480p DVD player, please contact our Customer
Service Center.
Connections
Connecting to an audio system and TV equipped with component video inputs
Signal Flow
(red)
To wall outlet
(white)
To PR
VIDEO
OUT
To ANALOG AUDIO OUT
To PB
VIDEO
OUT
To Y
VIDEO
OUT
To audio inputs of
the amplifier
(red)
(white)
To Y video inputs
To PB video inputs
To PR video inputs
Audio system
■
TV or monitor with component video inputs
Cables are not supplied
Before switching interlace video output
to progressive scan, be sure to set "Video
Output" to "Y PB PR")
You can temporarily switch the output signal for
better picture quality.
Press PROGRESSIVE on the remote control
during stop.
● Making the following setting.
On-screen display
Select:
Page
"Digital Output"
"Bitstream"
or
"PCM"
56
"Video Output"
Y PB PR
59
60
Notes
 Refer to the owner’s manual of the connected equipment as well.
 When you connect the DVD video player to other equipment, be sure to turn off the power and unplug all of
the equipment from the wall outlet before making any connections.
 If you place the DVD player near a tuner or radio, the radio broadcast sound might be distorted. In this case,
place the DVD video player away from the tuner and radio.
 The output sound of the DVD video player has a wide dynamic range. Be sure to adjust the receiver’s
volume to a moderate listening level. Otherwise, high volume sound may damage your hearing as well as
the speakers.
 Turn off the amplifier before you connect or disconnect the DVD video player’s power cord, if you leave the
amplifier power on, the speakers may be damaged.
 Analog audio out will not have sound DTS playback.
19
Connections
Connecting to Optional Equipment
You can enjoy high quality dynamic sounds by connecting the DVD video player.
to optional audio equipment.
● For connection to your TV, see “Connecting to a TV“.
18
19
● For details of output sound, see 42 .
● This section uses the following reference marks..
:Front speaker
:Rear speaker
:Sub woofer
:Center speaker
:signal flow
Notes:
● DO NOT connect the BITSTREAM/PCM AUDIO OUT
jack of the DVD video player to the AC-3 RF input of a
Dolby Digital Receiver. This input on your A/V receiver
is reserved for Laser disc use only and is incompatible
with the BITSTREAM/PCM AUDIO OUT jack of the DVD
video player.
● Connect the BITSTREAM/PCM AUDIO OUT jack of the
DVD video player to the "DIGITAL (COAXIAL)" input of a
Receiver or Processor.
● Refer to the owner’s manual of the connected equipment
as well.
● When you connect the DVD video player to other
equipment, be sure to turn off the power and unplug all
of the equipment from the wall outlet before making any
connections.
● The output sound of the DVD video player has a wide
dynamic range. Be sure to adjust the receiver’s volume to
a moderate listening level. Otherwise, the speakers and
your hearing may be damaged by a sudden high volume
sound.
● Turn off the amplifier before you connect or disconnect
the DVD video player’s power cord. If you leave the
amplifier power on, the speakers may be damaged.
20
Notice
● When you are connecting (via the BITSTREAM/PCM
AUDIO OUT jack) an AV decoder that does not
have Dolby Digital, Digital Theater Systems (DTS)
decoding function, be sure to set "Digital Output" to
"PCM" from the on-screen displays. Otherwise, high
volume sound may damage your hearing as well as
the speakers.
● When playing DTS-encoded discs (audio CDs),
excessive noise may be output from the analog audio
output jacks. To avoid possible damage to the audio
system, you should take proper precautions when the
analog audio output jacks of the DVD video player
are connected to an amplification system.To enjoy
DTS Digital SurroundTM playback, an external 5.1
channel DTS Digital SurroundTM decode system must
be connected to the BITSTREAM/PCM AUDIO OUT
jack of the DVD video player.
Connecting to an amplifier equipped with a Dolby Digital decoder
Amplifier equipped with a
Dolby Digital decoder
To COAXIAL type
digital audio out
Manufactured under license from Dolby
Laboratories. "Dolby", "Pro Logic" and the
double-D symbol are trademarks of Dolby
Laboratories. Confidential unpublished works.
Copyright 1992-1997 Dolby Laboratories. All
rights Reserved.
Connections
Dolby Digital
Dolby Digital is the surround sound technology used in theaters showing
the latest movies, and is now available to reproduce this realistic effect
the home. You can enjoy motion picture and live concert DVD video
discs with this dynamic realistic sound by connecting the DVD video
player to a 6 channel amplifier equipped with a Dolby Digital decoder
or Dolby Digital processor. If you have a Dolby Surround Pro Logic
decoder, you will obtain the full benefit of Pro Logic from the same
DVD movies that provide full 5.1-channel Dolby Digital soundtracks,
as well as from titles with the Dolby Surround mark.
● Use DVD video discs encoded
via the Dolby Digital recording
system.
● Make the following setting.
On-screen display
Select:
"Digital Output"
"Bitstream"
Recording system
To BITSTREAM/
PCM AUDIO OUT
D
Page
56
60
42
75Ω coaxial cable (Not supplied)
Connecting to an amplifier equipped with Dolby Surround Pro Logic
Dolby Surround Pro Logic
You can enjoy the dynamic realistic sound of Dolby Surround Pro
Logic by connecting an amplifier and speaker system(right and left
front speakers, a center speaker, and one or two rear speakers).
■ With an amplifier equipped with Dolby Digital connect the equipment
the same way as described in "Connecting to an amplifier equipped
with a Dolby Digital decoder." Refer to that amplifier’s owner’s
manual and set the amplifier so you can enjoy Dolby Surround Pro
Logic sound.
■ With an amplifier not equipped with Dolby Digital
connect the equipment as follows.
Amplifier equipped with
Dolby Surround Pro Logic
To audio input
To ANALOG
AUDIO OUT
● Make the following setting.
On-screen display
Select:
Page
“Digital Output”
“Bitstream”
or
“PCM”
56
60
* Connect one or two rear speakers.
The output sound from the rear speakers
will be monaural even if you connect two
rear speakers.
Audio cable (Not supplied)
21
Connections
Connecting to Optional Equipment
Connecting to an amplifier equipped with a DTS decoder
Digital Theater System(DTS)
DTS is a high quality surround technology used in theaters and now available
for home use, on DVD video discs or audio CDs.
If you have a DTS decoder or processor, you can obtain the full benefit of 5.1
channel DTS encoded sound tracks on DVD video discs or audio CDs.
Amplifier equipped with
a DTS decoder
To COAXIAL type
digital audio out
To BITSTREAM/
PCM AUDIO OUT
"DTS" and "DTS Digital Out" are
trademarks of Digital Theater Systems,
Inc
● Use DVD video discs or audio
CDs encoded via the DTS
recording system.
● Make the following setting.
On-screen display
Select:
Page
"Digital Output"
"Bitstream"
or
"PCM"
56
DTS
42
Recording system
60
75Ω coaxial cable (Not supplied)
Connecting to an amplifier equipped with a digital audio Input
2 channel digital stereo
● Make the following setting.
You can enjoy the dynamic sound of 2 channel Digital stereo by connecting an
amplifier equipped with a digital audio input and speaker system (right and left On-screen display Select: Page
front speakers).
56
"Digital Output"
Amplifier equipped with
a digital audio input
To COAXIAL type
digital audio out
To BITSTREAM/
PCM AUDIO OUT
75Ω coaxial cable (Not supplied)
22
"PCM"
60
Basic playback
Begin your operation.
● Playing a Disc
● Variable Speed Playback
● Locating a Desired Section
Basic playback
Playing a Disc
This section shows you the basics on how to play a disc.
CAUTION
Keep your fingers well clear of the disc tray as it is closing.
Neglecting to do so may cause serious personal injury.
ON/STANDBY indicator
PAUSE
O PE N/ CLO SE
VO O N/ ST A ND BY
1
DVD
VCD
CD
3
2,4
SKI P
P AU SE
S TO P
PLAY
PL AY
STOP
Basic Playback
Preparations
 When you want to view a disc, turn on the TV and select the video input connected to the DVD video
player.
 When you want to enjoy the sound of discs from the audio system, turn on the audio system and select the
input connected to the DVD video player.
1
Press the ON/STANDBY button.
POWER
The DVD video player turns on.
The ON/STANDBY indicator on the
player illuminates.
When the DVD video player is turned on
for the first time, make the proper settings
before proceeding to step 2.
2
3
Press OPEN/CLOSE.
The disc tray opens.
OPEN/CLOSE
Place the disc on the disc tray.
4
Press OPEN/CLOSE to close the disc tray.
Playback starts
OPEN/CLOSE
.
If you insert a DVD video disc that contains a top
menu, a menu may appear. Use the Direction
buttons to select the title you want to view, then
press ENTER to start playback. See "Locating a
title using the top menu".
 You may need to press the TOP MENU or
MENU button to display disc menu. (depending
on the actural DVD video disc.)
Note
For resuming playback, see
27
.
To start playback in stop mode
Press PLAY.
PLAY


24
There are two different disc sizes. Place the disc
in the correct guide on the disc tray. If the disc
is out of the guide, it may damage the disc and
cause the DVD video player to malfunction.
Do not place a disc which is unplayable in this
DVD video player.
Note
Video CD with PBC
 If you set Video CD with PBC in the player, the
MENU screen is appeared and you can choose
a scene from MENU screen.
 You can select PBC On or Off to press PBC
button on the remote control.
 If you press RETURN button on the remote
control while PBC is ongoing, the screen will
become previous one.
2, 4
1
STOP
PLAY
PAUSE
MENU
ENTER
/ / /
TOP MENU
■ To obtain a higher quality picture
Occasionally, some picture noise not usually visible during a normal broadcast may
appear on the TV screen while playing a DVD video disc because the high resolution
pictures on these discs include a lot of information. While the amount of noise depends
on the TV you use with this DVD video player, you should generally reduce the
sharpness adjustment on your TV when viewing DVD video discs.
VCD
CD
■ About DVD
The DVD
icons on the heading bar show the playable discs for the
VCD
CD
function described under that heading.
DVD : You can use this function with DVD video discs.
VCD : You can use this function with VIDEO CDs.
CD : You can use this function with audio CDs.
Press PAUSE/STEP during playback.
PAUSE/STEP
‚•
To resume normal playback, press
the PLAY button.
● The sound is muted during still
mode.
■ To stop playback
Press STOP.
STOP
mode).
Press ON/STANDBY and the ON/STANDBY
indicator turns off.
Note
Be aware that this equipment is still powered even after
the ON/STANDBY indicator turns off (standby mode) by
pressing the ON/STANDBY button. To disconnect this
equipment completely from the main power, pull out the
power plug from the wall outlet.
■ About the screen saver
■ To remove the disc
Press OPEN/CLOSE.
OPEN/CLOSE
■ To turn the power off (To enter the standby
Basic playback
■ To pause playback (still mode)
If you leave the DVD video player unattended for a
long while, the screen saver of the DVD video player
automatically appears. To turn off the screen saver,
press the PLAY button.
Remove the disc after the disc tray
opens completely.
■ Automatic Power Off function
If the DVD video player is stopped or the screen saver
is engaged for approximately 20 minutes, the DVD
video player automatically turns itself off.
Be sure to press the OPEN/CLOSE button to close
the disc tray after you remove the disc.
Notes
● Do not move the DVD video player during playback. Doing so may damage the disc.
● Use the OPEN/CLOSE button to open and close the disc tray. Do not push the disc tray while it is moving. Doing so
may cause the DVD video player to malfunction.
● Do not push up on the disc tray or put any objects other than discs on the disc tray. Doing so may cause the DVD
video player to malfunction.
● In many instances, a menu screen will appear after playback of a movie is completed. Prolonged display of an onscreen menu may damage your television set, permanently etching that image onto its screen. To avoid this, be sure
to press the STOP button on your remote control once the movie is completed.
25
Basic playback
Variable Speed Playback
REV
You can play discs at various speeds. Also you can resume playback from the location
where you stopped playback.
FWD
PLAY
PAUSE
STOP
SLOW
DVD
VCD
CD
Playing in fast reverse or fast forward directions
Press REV or FWD during playback.
REV
FWD
REV: Fast reverse playback
FWD: Fast forward playback
Each time you press the REV or
FWD button, the playback speed
changes.
DVD
VCD
■ To resume normal playback
Press PLAY.
PLAY
Notes

The DVD video player mutes sound and subtitles
during reverse and forward scan of DVD video discs.
And it also mutes sound during fast forward or fast
reverse play of audio CDs.

The playback speed may differ depending on the disc.
Playing frame by frame
Press PAUSE/STEP during still playback.
PAUSE/STEP
‚•
Each time you press the
PAUSE/STEP button, the picture
advances one frame.
■ To resume normal playback
Press PLAY.
PLAY
Note
The sound is muted during frame by frame playback.
26
DVD
VCD
Playing in slow-motion
SLOW
DVD
VCD
CD
1
Each time you press the SLOW
button, the slow-motion speed
changes.
■ To resume normal playback
Press PLAY.
PLAY
Note
The sound is muted during slow-motion playback.
Basic playback
Press SLOW during playback.
Resume playback from the same location
Press STOP once at the location where
you want to interrupt playback.
STOP
2
The DVD video player memorizes
the location where playback is
stopped.
■ To start playback from the beginning regardless
of the location where you stopped playback.
1. Press STOP twice.
STOP
The DVD video player deletes
the memory of the location.
2. Press PLAY.
Press PLAY.
PLAY
The DVD video player resumes
playback from the location where
you stopped playback.
PLAY
DVD
Playback starts from the beginning
of the current chapter.
VCD
CD
Playback starts from the beginning
of the disc.
Notes
 Resuming cannot function when:
-you change the parental lock setting or select a disc
menu language.
-you play a PBC-featured VIDEO CD while "PBC" is
set to "On".
-you open the disc tray.
 There may be a difference in the location where playback
resumes depending on the disc.
 The DVD player retains settings by the on-screen
display. This memory may need to be cleared for resume
playback.
27
Basic playback
Locating a Desired Section
TOP MENU
/ / /
ENTER
Normally, DVD video discs are divided into titles, and the titles are sub-divided into chapters. VIDEO CDs and audio
CDs are divided into tracks. You can quickly locate any specific title, chapter, or track.
DVD Video disc
Title 1
Chapter 1 Chapter 2
DVD
Chapter 1
Title 2
Chapter 2
VIDEO CD/audio CD
Chapter 3
C
Track 1
Track 3
Track 4
Track 5
Locating a title using the top menu
1
3
Press TOP MENU.
TOP MENU
The top menu appears on
the TV screen.
Notes

2
Press
want.
/ / /
Press ENTER.
ENTER
e.g.
28
Track 2
to select the title you

If the titles in the top menu are
assigned a number, you can
directly locate a specific title by
pressing its designated number
with the number buttons.


Playback starts from chapter
1 of the selected title.
The instructions above describe basic procedures
which may vary depending on the contents of the DVD
video disc. If different instructions appear on the TV
screen, follow those instructions.
If you display the top menu during playback and press
the TOP MENU button again without selecting any title,
the DVD video player may resume playback from the
point where you first pressed the TOP MENU button
(depending on the actual DVD video disc.)
This method of locating a title is available only on a disc
that contains a top menu.
Instruction notes of discs may refer to the button that
displays the top menu as TITLE button.
SKIP
CLEAR
PLAY
/ / /
ENTER
T
Number buttons
DVD
VCD
CD
Locating a desired section by entering the corresponding number
If you are using a VIDEO CD/audio CD, skip
step 2.
Then at step 3, enter the number for the track
you want using the number buttons.
e.g.
SEARCH
Search
Time
Title /Chapter
T
2
--:--:----/---
Press ENTER.
ENTER
Playback starts from the
selected section.
Press
a section (Time or
/ /to select
/
Title/Chaper) you want to locate.
e.g.
Search
Time
Title /Chapter
--:--:-011/005
Make sure that the spaces next to the Time
or Title/Chapter are highlighted.
3
DVD
VCD
CD
4
5
Repeat steps 2 and 3 if necessary.
Basic playback
1
Press T.
Notes
 Pressing the CLEAR button resets the numbers. To
clear the display, press the T button repeatedly until
the menu disappears.
 This method of locating a title is available only on a
disc that contains title numbers.
Press the number buttons to enter a
number of the section.
Locating a specific chapter or track
Press SKIP
or
repeatedly to access the
chapter or track number you want.
Playback starts from the selected chapter or track.
SKIP
SKIP
To locate succeeding chapter
or tracks.
Playback starts from the beginning
of the current chapter or track.
when you press twice, playback
starts from the beginning of the
preceding chapter or track.
Notes
 Some titles may not display chapter numbers.
 If you press the SKIP
or
button on the front
panel during playback, the DVD video player
performs fast reverse or fast forward playback.
You can vary the speed by pressing the button
repeatedly.
.
29
Advanced playback
Customizing the performance of your DVD video player.
● Accessing a Specific Location Directly
● Repeating a Specific Segment
● Playing in a Varied Order
● Playing in a Favorite Order
● Zooming a Picture
Selecting the Picture Enhancement
(E.P.M.)
● Selecting the Sound Enhancement
(E.A.M.)
● Selecting the the Camera Angle
● Selecting Subtitles
● Selecting a Language
● On-screen Display Operation
● Playing MP3/WMA Files
● Viewing JPEG Files
Advanced playback
Accessing a Specific Location Directly
CLEAR
You can access specific location by entering its corresponding time (hours,
minutes, seconds)
3
3
1
2
DVD
VCD
CD
/ / /
Entering the time counter of the desired location
1
Press T once.
Press the button, the time counter
is highlighted.
SEARCH
T
e.g.
2
ENTER
Search
Time
Title /Chapter
--:--:----/---
Press the number buttons to enter the
time.
e.g.
0
1
3
Press ENTER.
2
5
3
0
Playback starts from the
specified location.
Notes
 Some discs may not respond to this process.
 Some scenes may not be located precisely as you
specified.
 This method for accessing specific locations is
available only within the range of the total time of the
DVD video disc or VIDEO CD/audio CD.
Search
Time
01:25:30
Title /Chapter ---/---
DVD
VCD
CD
Setting a bookmark
1
Press T twice during playback.
SEARCH
T
2
3
32
The following menu appears.
Bookmark
Bookmark
Bookmark
--:--:---:--:---:--:--
Press the ENTER button at the piont you
want to locate.
The point is registered as a bookmark.
Press the / / buttons
to highlight the
/
next two spaces to set the bookmarks as
you preferred.
■ To clear the bookmark
Press CLEAR.
■ To quit the feature
Press T again.
■ To jump to the bookmarks.
Press T twice to display the bookmark menu. Highlight
the items by pressing the / / buttons
and select a
/
bookmark, press ENTER.
Playback starts from the the point that is registered.
Notes
 You can save three bookmarks.
 There may be a difference between a marked point
and the location you actually jump to.
 Some points may not be marked.
 A bookmark will be erased when:
- you turn off the power of the DVD video player.
- you open the disc tray
 A bookmark may not be set on an MP3/WMA/JPEG
file.
Repeating a specific segment
You can specify a desired segment and repeat it.
A-B RPT
DVD
VCD
CD
1
Press A-B RPT at the beginning of the
segment (point A) you want to play
repeatedly.
A-B RPT
Rep A-
Press A-B RPT again at the end of the
segment (point B).
The DVD video player automatically
returns to point A and starts repeat
playback of the selected segment. (A-B)
A-B RPT
Rep A-B
■ To resume normal playback
Press A-B RPT until "Rep Off" appears on the TV
screen.
A-B RPT
Rep Off
Notes
 Some discs may not permit A-B repeat operation.
 You can specify a segment only within the current
title or track (VIDEO CD/Audio CD).
 There may be a slight difference between point A
and the location where playback actually resumes
depending on the disc.
Advanced playback
2
Repeat a specific segment
33
Advanced playback
Playing in a Varied Order
You can play titles, chapters within a title, or track in a varied order.
ENTER
/ / /
1,2
DVD
VCD
CD
Playing titles, chapters or tracks in a varied order
1
Press PLAY MODE during playback, the
screen displays as follows.
PLAY MODE
2
Press PLAY MODE.
The DVD video player automatically
enters selected playback mode.
Highlight the items you want to select by
pressing / /, then
/ press ENTER repeatedly.
Play Mode
Random
Repeat
eat
e.g.
■ To resume normal playback
Off
Off
While the display appears on the screen, press the
ENTER button repeatedly in both items, until the
playback mode changes to "Off".
DVD
ENTER
VCD
CD
ENTER
Off
On
DVD
Off
Chapter
Title
VCD
CD
Off
Track
All
Chapter/Title/Track Repeat:
Repeats the current chapter/title/track.
All Repeat:
Repeats the entire disc.
Chapter Random:
Plays the chapters within the current title in random
order.
Title/Track Random:
Plays the title/track in random order.
Random Off/ Repeat Off:
Resumes normal playback.
If you press the PLAY MODE button during
playback, the DVD video player automatically enters the selected playback mode
after finishing the current title, chapter, or
track.
34
Notes
 Some discs may not permit these operations.
 You cannot set Playback Mode during stop.
Playing in a Favorite Order
You can combine your favorite titles, chapters or tracks and play them in the
order you determine. You can program up to 12 selections into the memory.
(Memory playback)
CLEAR
PLAY
/ / /
ENTER
2
DVD
VCD
CD
1
1
Setting titles, chapters or tracks in a favorite order
■ To change the programmed selections
Insert a disc and press MEMORY.
The following display appears.
e.g. (DVD)
Memory Input Title/Chapter
1 -- -2 -- -3 -- --
4 -- -5 -- -6 -- --
Play Memory
7 -- -8 -- -9 -- --
10 -- -11 -- -12 -- --
Clear All
-- --
Chapter number
Title number
e.g. (VIDEO CD/Audio CD)
Memory Input Track
1 --2 --3 ---
4 --5 --6 ---
Play Memory
7 --8 --9 ---
10 --11 --12 ---
Clear All
---
2
Track number
Select the items in order you want by pressing
the number buttons.
Each time you press the
button, the
/ / /
space is highlighted in turn. Highlight where you
want to enter, then press the corresponding number
buttons.
To select tracks from a VIDEO CD/audio CD in order,
press the number buttons for the track.
3
Highlight "Play Memory" while the display
appears on the TV screen, then press the ENTER
button.
ENTER
ENTER
The DVD video player starts memory
playback.
■ To cancel the programmed selections
1 while the display appears on the TV screen,
press / / /
to move the highlighted
bar to the item you want to cancel.
2 Press CLEAR.
Advanced playback
MEMORY
1 While the display appears on the TV screen,
press / / / to move the highlighted
bar to the item you want to change.
2 Change the selection following the
instructions in step 2.
■ To resume normal playback from memory
playback
Press MEMORY button.
Press / / / to move the highlighted bar to
"Clear All", then press the ENTER. All the input
programmes will be cleared.
PLAY
Press PLAY button to resume
normal playback.
Normal playback will start
from first location.
■ To program during playback.
If you press the MEMORY button during
playback, a programming display appears.
Follow steps 2 and 3.
Notes
 Some discs may not permit memory playback
operation.
 When you input only title number, the playback
starts from the first chapter of the selected title.
 If you press the PLAY MODE button during
memory playback, the DVD video player repeats
the current memory playback.
 If you press the MEMORY or PLAY button while
the display appears on the TV screen, the display
disappears.
 The programmed selections will be cleared when
you turn off the DVD video player.
35
Advanced playback
Zooming a Picture
You can magnify areas within a picture.
/ / /
ENTER
ZOOM
DVD
VCD
Zooming a Picture
■ To resume normal playback
Press ZOOM button during normal, slow or
still playback.
ZOOM
e.g.
Press the ZOOM button repeatedly until the
icon " Off " appears on the TV screen.
ZOOM
The DVD video player enters
the zoom playback mode and
displays the icon.
1
As you repeatedly press the
ZOOM button, the magnification
level changes.
e.g.
1
2
3
If you press the / / /
the zoom point shifts.
36
Off
buttons,
Notes
 Some discs may not respond to zoom feature.
 During some scenes, the buttons may not work as
described.
 Zooming does not work on subtitles or menus included
on DVD video discs.
 The magnification level varies depending on the
setting of TV shape you select. 59
Selecting the Picture Enhancement (E.P.M.*)
You can easily select a preferred picture enhancement.
3
* E.P.M.: Enhanced Picture Mode
2
1
DVD
VCD
1
Selecting the picture enhancement
■ To exit the picture enhancement selection
Press E.P.M.
3
Video Enhance
Brightness
Sharpness
Select the item by pressing
Press the
/ / /
08
08
E.P.M.
Note
Actual effect to picture may vary depending on the
TV. Make a selection according to your preference.
Advanced playback
E.P.M.
2
Press E.P.M. again.
The picture enhancement menu
appears.
/ ./ /
buttons.
Each time you press the button, the picture
enhancement changes.
Brightness:
Brightness levels raised for enhanced picture
clarity.
Sharpness:
For sharpness reproduction.
37
Advanced playback
Selecting the Sound Enhancement (E.A.M.*)
You can easily select a preferred audio enhancement.
* E.A.M.: Enhanced Audio Mode
1, 2
DVD
VCD
1
Selecting the sound enhancement
■ To exit the audio enhancement selection
Press E.A.M.
The sound enhancement
icon appears.
E.A.M.
2
3D On
Select the sound enhancement
by pressing the E.A.M. button
repeatedly.
Each time you press the button, the
sound enhancement changes.
3D Off
3D On
3D:
To obtain expansive virtual surround sound
effects from just two speakers.

38
Leave the DVD video player unattended for about
5 seconds after having made a selection.
To use this enhancement of sounds output
from the BITSTREAM/PCM jack, be sure
to set "Digital Output" to "PCM". See 60 .
Notes
 Actual effects to sounds may vary depending on the
speaker system. Make a selection according to your
preference.
 Actual effects to sounds may vary depending on the
disc.
 When the DVD video player is connected to an amplifier
equipped with Dolby Pro Logic, select "3D Off".
Otherwise, Dolby Pro Logic may function differently
than usual.
Selecting the Camera Angle
1, 2
If the scene was recorded from multiple angles, you can easily change
the camera angle of the scene you are watching.
    
Changing the camera angle
DVD
1
Press ANGLE while playing a scene
recorded with multiple angles.
e.g.
2
1/2
Advanced playback
While playing a scene recorded
with multiple angles, angle icon
will be displayed for about 3
seconds, press the ANGLE
button.
ANGLE
Notes
 You cannot change the camera angle during still
playback.
 If you pause a picture immediately after changing a
camera angle, the resumed playback picture may not
display the new camera angle.
Press ANGLE while the angle icon
is displayed on the TV screen.
ANGLE
Each time you press the
ANGLE button, the camera
angle changes.
1/2
2/2
39
Advanced playback
Selecting Subtitles
You can display subtitles on the TV screen and select a subtitle language
from those included on the DVD video disc.
Good evening!
DVD
1, 2
ABuenas tardes!
BONSOIR!
Selecting a subtitle language
1
SUBTITLE
The current
displayed.
e.g.
subtitle
setting
Press the SUBTITLE button repeatedly until
Off appears on the screen.
is
SUBTITLE
1/3 ENG
The abbreviation of the language appears
instead of the language name.
.
2
■ To turn subtitles off
Press SUBTITLE during playback.
Press SUBTITLE while the
subtitle setting is displayed on
the TV screen.
Notes
 Some DVD video discs are set to display subtitles
automatically, and you cannot turn them off even if you
set the subtitle function to off.
 During some scenes, the subtitles may not appear
immediately after you press the SUBTITLE button.
 Some DVD video discs will allow you to make subtitle
selections and turn subtitles on or off only via the disc
menu.
SUBTITLE
Each time you press the
SUBTITLE button, the subtitle
languages included on the DVD
video disc change.
1/3 ENG
2/3 FRE
3/3 SPA
Off
Notes
 When you turn on the DVD video player or replace a disc, the player returns to the initial default setting.
When you select a subtitle language which is not included on the disc, the DVD video player plays a prior language
programmed on the disc.
 During some scenes, the subtitles may not appear immediately after you change the subtitle language.
40
Selecting a Language
You can select a preferred language and sound recording system from those
included on the DVD video disc.
DVD
1, 2
Selecting a playback audio setting
AUDIO
The current audio
setting is displayed.
e.g.
1/2
D 2 ch ENG
2
Press AUDIO, the audio setting is
displayed on the TV screen.
AUDIO
e.g.
Each time you press the
AUDIO button, the audio
settings included on the DVD
video disc change.
1/2
D 2 ch ENG
2/2
D 5.1 ch ENG
Advanced playback
1
Press AUDIO during playback.
The abbreviation of the language appears
instead of the language name.
■ Selecting sound channels of VIDEO CDs
You can switch left and right channels by
pressing the AUDIO button repeatedly during
playback.
AUDIO
Notes
 When you turn on the DVD video player or replace a
disc, the player returns to the initial default setting.
If you select a sound track which is not included on
the disc, the DVD video plays a prior sound track
programmed on the disc.
 Some discs allow you to change audio selections only
via the disc menu. If this is the case, press the MENU
button and choose the appropriate language from the
selections on the disc menu.
41
Advanced playback
DVD
VCD
Selecting a playback audio setting
■ Output sound conversion table
Output
Input
DVD
video disc
VIDEO CD
Audio CD
BITSTREAM/PCM jack
“Digital Output” 56
60
ANALOG
AUDIO jacks
“Bitstream”
“PCM”
Dolby Digital
Bitstream
PCM
YES
Linear PCM
PCM
PCM
YES
DTS
Bitstream
Bitstream
--
MPEG1, MPEG2
PCM
PCM
YES
MPEG1
PCM
PCM
YES
Linear PCM 44.1 kHz/16 bit
PCM
PCM
YES
DTS
Bitstream
Bitstream
Noise
MP3/WMA
PCM
PCM
YES
: 3D sound enhancement can function.
 Signals of 96kHz from the BITSTREAM/PCM jack are depressed to 48 kHz by down sampling process when:
- “3D On” is selected. 38
- a copyright protected disc is played.
 Quantization bit of signals of 20 bit or higher which is output from the BITSTREAM/PCM jack is 16 bit if they are in
a copyright protected disc.
42
On-screen Display Operation
When you turn on the on-screen display, you can view information on operational
status and access features and settings.
ENTER
/ / /
NAVI
DVD
VCD
CD
On-screen display operation
Press NAVI
NAVI
The following display appears.
Each time you press the NAVI button, the on-screen display changes as follows.
44
for details on the features.
e.g. When playing a DVD video disc
Select by pressing
/ / / then press
ENTER to access the feature.
1/3
24/28
Advanced playback
See the pages in
00:23:53
Off
43
Advanced playback
On-screen Display Operation (Continued
(Continued)
On-screen display operation
■ Features
1/3
Title number
(Track number)
Total titles
Title number (Track number)
To display the current title or track number.
Total chapters
Chapter number
To display the current chapter number.
24 / 28
Chapter number
: To stop playback.
: Playback starts from the beginning of the
current chapter.
: To start playback.
: To locate succeeding chapters or tracks.
: To pause playback.
00:23:53
Displays elapse time of the current title or
track.
(Continued)
44
DISPLAY
■ Viewing the operational status
1 Press DISPLAY once.
The following display appears.
VCD
CD
Advanced playback
Time counter
DVD
Elapsed time/remaining time of the current title
Elapsed time/remaining time of the current track
00:16:24
01:47:36
2 Press DISPLAY twice.
The following display appears.
Chapter number 29
Title number 29
DVD
D
Title 1/3
Audio
Subtitle
S
Bitrate
00:16:24 01:47:36
Chapter 11/28 Angle
1/1
1/2
D 5.1 ch ENG
4/4 ENG
4.543Mbps
3 To turn off the display, press DISPLAY again.
Note
 Some discs may not display the time counter.
Angle Setting 39
A
Language setting 41
Subtitle Setting 40
Bit rate (Mbit/s)
Amount of picture, sound and subtitle
data in the DVD video disc transferred
per second.
The larger the value is, the more data
processed, but this does not necessarily
insure better picture quality.
45
Advanced playback
2
Playing MP3/WMA Files
SKIP
You can play MP3/WMA files that have been recorded on a CD-R or
CD-ROM on the DVD video player.
3
PAUSE/STEP
PLAY
/ / /
ENTER
Playing MP3/WMA files
■ Preparations

Make sure that a disc you want to play is compatible with this DVD video player.
1
Place a CD that contains MP3/WMA files
on the disc tray.
2
3
Press OPEN/CLOSE to load the disc.
OPEN/CLOSE
Playback starts.
■ Selecting a track (file) in the disc
1 Press
/ / / to select the column of MP3/WMA file.
Press / / to/select the MP3/WMA file on a list of
column.
2 Press ENTER or PLAY to play the MP3/WMA file.
Press
or
during playback to skip the
tracks.
3 Press number buttons 1-10 to select the track
which you want, the DVD video player will play the
selected track. If the track number is bigger than 10,
press +10 first, then next number.
To stop playback, press STOP.
STOP
■ To pause playback
Press PAUSE/STEP during playback.
PAUSE/STEP
‚•
To resume normal playback, press
the PLAY button.
Notes
 You can select a track by designating a track
number.
 Press the T button, and input the number you want
to play, press ENTER.
 Letters of a file/folder name overflowing the given
space will not be displayed.
 You cannot play in Fast reverse or Fast forward
during MP3/WMA playback.
Notes
 Some discs may not permit this operations
 WMA tracks copy-protected cannot be played.
 The BITSTREAM/PCM jack outputs MP3/WMA sounds in the linear PCM format regardless of the current "Digital
Output" selection. 42
 If you stop playback by pressing STOP button, and then press the PLAY button, playback will start from the beginning
of the track.
 The SKIP and PLAY MODE functions are also available.
46
Advanced playback
Playable files
MP3/WMA disc compatibility with this player is limited as follows:
Playable discs:
CD-ROM, CD-R (650MB / 74 min. only)
CD-RW is not recommendable.
Sampling Frequency: 44.1 kHz only
Bit rate:
WMA: 48 kbps - 192 kbps (CBR)
MP3: 32 kbps - 320 kbps (CBR)
CD physical format:
Mode 1, Mode 2 XA Form 1
File system:
ISO9660 Level 1, 2 or Joliet
File name:
A file name should be in alphabet and numbers only, and must incorporate "MP3" or "WMA"
extension.
e.g. "********.MP3", "********.WMA"
Total number of folders:
Less than 256
Total number of files: Less than 1000
WMA codec version: V7 or V8 (Stereo sound only)
This DVD video player requires discs/recordings
to meet certain technical standards in order to
achieve optimal playback quality. Pre-recorded
DVDs are automatically set to these standards.
There are many different types of recordable disc
formats (including CD-R containing MP3/WMA
files). Given the fact that technology in this area
is still maturing, Toshiba cannot guarantee that
all genre of recordable discs will produce optimal
playback quality. The technical criteria set out in
this owner’s manual are meant as a guide only.
Customers should also note that permission
is required in order to download MP3 files and
music from the internet. Toshiba has no right
to grant such permission. Permission should
always be sought from the copyright owner.
Microsoft, Windows Media, and the
windows Logo are trademarks or
registered trademarks of Microsoft
Corporation in both the United States
and other countries.
47
Advanced playback
Viewing JPEG Files
You can play JPEG files that have been recorded on a CD-R or CD-ROM on the DVD video player.
You can select a preferred view: a page of 9 thumbnail images, a single image view, and slide show of a
selected folder.
Also, rotating, enlarging and shifting of each image can be possible.
Prev
Slide show
Next
Thumbnail
Single image view
Starting a slide show
■ Preparations


Prepare a disc that contains JPEG files you want to view. 53
Make your TV shape conform to the 4:3 picture size. Only 4:3 pictures can be played regardless of the function
settings via the on-screen displays of the DVD video player. If the TV is adjusted to other sizes, e.g. "WIDE"
images will appear to be horizontally expanded. For details, refer to the owner's manual of your TV.
1
Press OPEN/CLOSE to open the disc tray.
OPEN/CLOSE
2
3
Place a CD that contais JPEG files on the disc tray.
Press OPEN/CLOSE.
OPEN/CLOSE
The disc tray closes, and the DVD video player reads the loaded disc.
e.g.
CD
Searching for files...
When a JPEG disc is loaded into the player, slide show starts automatically. Each picture in the
disc will be displayed consecutively in a slide show presentation and will be seated to fill most
of your TV screen.
48
1, 3
STOP
PAUSE/STEP
4
To quit the JPEG playback, press STOP.
STOP

If you press STOP button, you can return to the folder list.
Pressing the OPEN/CLOSE button to open the disc tray can also quit the playback.
■ To view a single image (To pause slide show)
Press PAUSE/STEP
Advanced playback

PAUSE/STEP
‚•
■ To confirm a photo number
See
51
■ To magnify an image
See
52
■ To rotate an image
See
52
■ To return to the thumbnail view
See
52
Note
 Some files may not display their own entire images depending on the size.
49
Advanced playback
Viewing JPEG Files (Continued)
STOP
PAUSE/STEP
PLAY
/ / /
ENTER
1
Starting from a thumbnail view and a folder list
■ To display a thumbnail view
■ To display a folder list
1. Press TOP MENU during playback.
TOP MENU
1. Press STOP button during playback.
STOP
e.g.
e.g.
CD
2/213
HI-RES
1
2
3
4
5
Prev
16001
16002
16003
16004
16005
6
7
8
9
10
16006
16007
16008
16009
16010
Next
A thumbnail view appears
You can select an image to play at your preference.
A folder list appears
You can select a folder (file) to play at your
preference.
2. Turn the page if necessary.
Press / / / to highlight "Prev "
or "Next " from thumbnail view, then
press ENTER.
3. Select the viewing options at your preference.
Viewing a single image: see 51
50
2. Press / / / buttons to select your desired file,
and then press the ENTER or PLAY button to start
playback.
3
2
1
2
DISPLAY
T
Viewing a single image
1
Press DISPLAY.
The photo number will be displayed on the TV screen.
DISPLAY
Press ENTER or PLAY.
ENTER
The selected image is
displayed.
PLAY
‚•
3
■ To confirm a photo number
■ To search a photo number
1. Press T.
The menu appears on the TV screen.
SEARCH
T
e.g.
Search
Track
To pause playback
Press PAUSE/STEP during
playback.
Advanced playback
2
On a thumbnail view, select an image by
pressing
/ / / .
----
2. Input the number you want to play by pressing the
number buttons.
To quit the JPEG playback, press STOP.
If you press the PLAY button
after pressing the STOP button,
slide show starts.
 Pressing
the
OPEN/CLOSE
button to open the disc tray can
also quit the playback.

Notes
 To turn it off, press the T button.
 While a photo number image is displayed, use the
Note
number buttons to select a desired photo number and
 Some files may not display their own entire image
press the ENTER button. The slide show will begin from
depending on their size.
that selected image.
51
Advanced playback
Viewing JPEG Files (Continued)
ANGLE
STOP
/ / /
ZOOM
TOP MENU
Viewing a single image
■ To display a folder list
■ To magnify an image
Press STOP button during playback.
Press ZOOM repeatedly.
STOP
ZOOM
You can select a folder (file) to play.
See 50
Each time you press the ZOOM button, the
magnification level changes as follows:
1 (The icon and monitor scope appear.)
3 (Maximum)
2
Off (The icon
and monitor scope disappear.)
■ To rotate an image
1. Press ANGLE during playback.
e.g.
Original
2. Press ANGLE repeatedly.
ANGLE
Each time you press the ANGLE button,
you can set rotation of the image in 90
degree increments.
Original (The icon appears)
180 Deg CW
90 Deg CCW
90 Deg CW
Original
Note
 The DVD video player may re-display an image if you
rotate it.
52
Press TOP MENU.
TOP MENU
Notes
 While changing the magnification level, you can shift
/ / / buttons.
the image. Press and hold the
 Exiting an image cancels the current selection of the
magnification level.
ANGLE
■ To return to the thumbnail view
See
50
JPEG files compatibility
Discs whose compatibility with this DVD video player has been confirmed by TOSHIBA are as follows.
Many of these discs, when loaded, will make the DVD video player enter the automatic mode to play a prescribed
folder in the disc. To play other folders, display a folder list and select a folder.
JPEG disc compatibility with this DVD video player is limited as follows:
Playable discs
CD-ROM,CD-R(650MB/74min.only)
CD-RW is not recommendable.
CD physical format:
Mode 1, Mode 2 XA Form 1
File system:
ISO9660 level 1,2 or Joliet
File name:
A file name should be in alphabet and numerals only, and must incorporate
“JPG”extension.
e.g. “********.JPG”
Total number of folders:
Less than 256
Total number of files:
Less than 1000
Advanced playback
CANON Quick CD
FUJICOLOR CD
Kodak Picture CD
NORITSU QSS CD
Some files may not display their own entire image depending on the size.
Some discs may not permit this operation. Especially , the following conditions of included files will increase the disc’s
disability.
1.Pixels over 3072× 2048 in height and/or width
2.File format except Exif
53
Function setup
You can customize the default settings to your preference.
● Customizing the Function Settings
● Table of Languages
Function setup
Customizing the Function Settings
You can customize the default settings to your preference.
RETURN
3, 4
2
1, 6
DVD
VCD
CD
Setting procedure
1
The following on-screen
display appears.
Language
2
3
Press SETUP during stop.
Video
Audio
/ / to/ select the setting you
Press
want to change, then press ENTER.
ENTER
Parental
Press
/ / / to select a item for the
setting you want to change, and then
press ENTER.
4
Change the selection by
/ /, /by
referring to the corresponding pages
( 58 -), then press ENTER.
ENTER
(See the next page)
Language
Language settings
Video
Picture output settings
Audio
Output sound settings
Parental
Parental lock settings
Initial setup
5
6
Change step 3 and 4 to change other
setting.
To select another operation, go back to
step 2.
Press SETUP.
SETUP
The on-screen display disappears.
■ To return to the previous display
Press the RETURN button.
RETURN
Notes
 To quit the procedure, press the SETUP button to turn
off the on-screen display.
 The SETUP button can only function during stop.
56
Setting
Language OSD Menu
Subtitle
Audio
DVD Menu
Video
TV Shape
Video Output
Digital Output
Parental
Password
Parental
Default
Page
To select a preferred language for on-screen
displays.
58
To select a preferred language for subtitles
58
To select a preferred language for the sound track
58
To select a preferred language for the disc menus.
58
To select a picture size according to the aspect
ratio of your TV.
59
DVD
VCD
To select a proper video output mode
corresponding to your connected TV.
59
DVD
VCD
CD
To select an output sound format corresponding
to your system connection.
60
To turn the parental lock function on or off.
60
When the parental lock feature is activated, the
settings can be changed
61
To install the initial system setting.
61
DVD
VCD
CD
DVD
DVD
DVD
DVD
DVD
DVD
DVD
VCD
CD
Function setup
Audio
Details
57
Function setup
Customizing the Function Settings (continued)
Setting details
Language
Language
OSD Menu
enu
Subtitle
Audio
DVD Menu
OSD Menu
DVD
VCD
Video
Audio
Parental
English
English
English
English
CD
English: To view On-screen displays in English.
Français: To view On-screen displays in French.
Español: To view On-screen displays in Spanish.
Subtitle
DVD
English: To display subtitles in English.
Français: To display subtitles in French.
Español: To display subtitles in Spanish.
Auto:
To display prior subtitle recorded on the
disc.
Off:
To disable subtitles.
Notes
 Some DVD video discs may be set to display
subtitles in a different language than you
selected. A prior subtitle language may be
programmed on the disc.
 Some DVD video discs allow you to change
subtitle selections only via the disc menu. If this
is case, access the disc menu and choose the
appropriate subtitle language from the selection
on the disc menu.
58
Audio
DVD
English: To play sound track in English.
Français: To play sound track in French.
Español: To play sound track in Spanish.
Note
 Some DVD video discs may be played in a
different language than you selected. A prior
language may be programmed on the disc.
DVD Menu
DVD
English: To display disc menus in English.
Français: To display disc menus in French.
Español: To display disc menus in Spanish.
Note
 Some DVD video discs may not include your
pre-select language. In this case, the DVD video
player automatically displays a prior language
programmed on the disc.
Video
Language
TV Shape
Video
Audio
Parental
4:3 Lettrer Box
Video Output
Y PB PR:
Select when you connect your DVD
video player with Y, PB, PR jacks.
DVD
Select when a standard 4:3 TV
is connected. Displays pictures
cropped to fill your TV screen.
Either or both sides of the picture
are cut off.
4:3 Letter Box:
Select when a standard 4:3
TV is connected. Displays
theatrical images with masking
bars above and below the
picture.
16:9 Wide
Select when a 16:9 wide TV is
connectd.
Note
When "Y PB PR" is set and you select the
progressive output signal, no video signals are
output from the VIDEO OUT jack and the S VIDEO
OUT jack.
Function setup
TV Shape
VCD
Select when you connect your DVD
video player with VIDEO OUT jack.
Video Output CVBS
4:3 Pan Scan:
DVD
CVBS:
Notes
 The displayable picture size is preset on the
DVD video disc. Therefore, the playback picture
of some DVD video discs may not conform the
picture size you selected.
 If you select "16:9" and own a 4:3 TV set,
the DVD playback picture will be horizontally
distorted during playback. Images will appear to
be horizontally compressed. Always be sure that
your TV shape conforms to the actual TV in use.
59
Function setup
Customizing the Function Settings (continued)
Setting details
Audio
Digital Output
Language
Video
Digital Output
PCM
DVD
VCD
Audio
Parental
CD
Select the output sound format corresponding
to your system connection.
For details of sound recording systems, see 42
PCM:
Bitstream:
Select when connected to a 2 channel
digital stereo amplifier. See 22
The DVD video player outputs sounds
in the PCM 2ch format when you
play a DVD video disc recorded on
the Dolby Digital, MPEG1 or MPEG2
recording system.
Select when connected to an amplifier
equipped with a Dolby Digital, DTS,
decoder. See 21 22
Note
When you make a connection to a TV, or Dolby
Surround Pro Logic or stereo system via the analog
audio jacks, select "Bitstream" or "PCM".
Parental
Password
Language
Video
Audio
Parental
----
Password
Parental
8. Adult
Default
No
DVD
DVD video discs equipped with the parental lock
function are rated according to their content. The
contents allowed by a parental lock level and the
way a DVD video disc can be controlled may vary
from disc to disc. For example, if the disc allowed
you could edit out violent scenes unsuitable for
children and replace them with more suitable
scenes, or lock out playback of the disc altogether.

DVD video discs may or may not respond to the
parental lock settings. This is not a defect in the
DVD video player. Make sure this function works
with your DVD video discs.
:The parental lock feature does not function.
After pressing the ENTER button, follow the
step 1) below.
:To activate the parental lock feature or change
the settings.
After pressing the ENTER button, follow steps
1) - 3)
1) Press the number buttons to create a personal
4-digit security code, then press ENTER.
The pre-set password is 0000.
If you make a mistake before pressing the
ENTER button, press the CLEAR button and
enter your 4-digit security code again.
2) Select "Parental" by pressing the
/ / buttons.
/
3) Press the ENTER button repeatedly to select the
playback level as your preference.
(continued)
60
Parental
Default
DVD
Language
Password
Parental
Default
Video
Audio
Parental
---8. Adult
No
The parental lock level is equivalent to the following
ratings.
1. Kid Safe
2. G
3. PG
4. PG-13
5. PG-R
6. R
7. NC-17
8. Adult
VCD
Language
Password
Parental
Default
CD
Video
Audio
Parental
---8. Adult
Yes
If you want to return the initial settings such as
Language, Video, Audio and etc. to the factory default, do the following:
1) Press the / / buttons
to select “Default”, and
/
press the ENTER button.
2) Select “Yes” according to your preference, and
press the ENTER button.
Note:
When you reset the DVD vide player to the factory
default, the DVD video player will take 3-5 seconds to reset.
Function setup
You cannot play DVD video discs rated higher than
the level you selected unless you cancel the parental
lock function.
For example, when you select 7, discs rated higher
than level 7 are locked out and cannot be played.
DVD
The parental lock level for other countries/areas
than U.S. are included for future use. Check the
appropriate parental lock level when you buy a DVD
video disc equipped with the parental lock feature
in the future.
When the parental feature is activated, you can
change the parental lock level according to your
preference. For details, see 60 .
■ Forgetting your password
If you forget the password, you can erase your
current password by pressing number button
0 on the remote control four times, then press
ENTER button to confirm the setting.
61
Function setup
Table of Languages
Table of languages and their abbreviations
Abbreviation
--CHI (ZH)
DUT (NL)
ENG (EN)
FRE (FR)
GER (DE)
ITA (IT)
JPN (JA)
KOR (KO)
MAY (MS)
SPA (ES)
AA
AB
AF
AM
AR
AS
AY
AZ
BA
BE
BG
BH
BI
BN
BO
BR
CA
CO
CS
CY
DA
DZ
EL
EO
ET
EU
FA
FI
FJ
FO
FY
GA
GD
GL
62
Language
No alternate
language
Chinese
Dutch
English
French
German
Italian
Japanese
Korean
Malay
Spanish
Afar
Abkhazian
Afrikaans
Amharic
Arabic
Assamese
Aymara
Azerbaijani
Bashkir
Belorussian
Bulgarian
Bihari
Bislama
Bengali, Bangla
Tibetan
Breton
Catalan
Corsican
Czech
Welsh
Danish
Bhutani
Greek
Esperanto
Estonian
Basque
Persian
Finnish
Fiji
Faroese
Frisian
Irish
Scottish Gaelic
Galician
Abbreviation
GN
GU
HA
HI
HR
HU
HY
IA
IE
IK
IN
IS
IW
JI
JW
KA
KK
KL
KM
KN
KS
KU
KY
LA
LN
LO
LT
LV
MG
MI
MK
ML
MN
MO
MR
MT
MY
NA
NE
NO
OC
OM
OR
PA
PL
PS
Language
Guarani
Gujarati
Hausa
Hindi
Croatian
Hungarian
Armenian
Interlingua
Interlingue
Inupiak
Indonesian
Icelandic
Hebrew
Yiddish
Javanese
Georgian
Kazakh
Greenlandic
Cambodian
Kannada
Kashmiri
Kurdish
Kirghiz
Latin
Lingala
Laotian
Lithuanian
Latvian, Lettish
Malagasy
Maori
Macedonian
Malayalam
Mongolian
Moldavian
Marathi
Maltese
Burmese
Nauru
Nepali
Norwegian
Occitan
(Afan) Oromo
Oriya
Panjabi
Polish
Pashto, Pushto
Abbreviation
Language
PT
QU
RM
RN
RO
RU
RW
SA
SD
SG
SH
SI
SK
SL
SM
SN
SO
SQ
SR
SS
ST
SU
SV
SW
TA
TE
TG
TH
TI
TK
TL
TN
TO
TR
TS
TT
TW
UK
UR
UZ
VI
VO
WO
XH
YO
ZU
Portuguese
Quechua
Rhaeto-Romance
Kirundi
Rumanian
Russian
Kinyarwanda
Sanskrit
Sindhi
Sango
Serbo-Croatian
Singhatese
Slovak
Slovenian
Samoan
Shona
Somali
Albanian
Serbian
Siswati
Sesotho
Sundanese
Swedish
Swahili
Tamil
Telugu
Tajik
Thai
Tigrinya
Turkmen
Tagalog
Setswana
Tongan
Turkish
Tsonga
Tatar
Twi
Ukra
Urdu
Uzbek
Vietnamese
VolapÜk
Wolof
Xhosa
Yoruba
Zulu
Others
●Before calling Service Personnel
●Specifications
●LIMITED UNITED STATES WARRANTY DVD PLAYERSEXCHANGE WARRANTY
Others
Before Calling Service Personnel
Check the following guide for the possible cause of a problem before contacting service.
Symptoms and correction
Symptom
Cause
Correction
No power.
The
Connect
18
The DVD video player turned
off by itself.
The
Press
24
No picture.
The
Select
The
Connect
The
Select
The
Connect
power plug is disconnected.
automatic power off function
turned the unit off.
TV is not set to receive DVD signal
output.
video cable is not connected
correctly.
No sound.
equipment connected with the
audio cable is not set to receive DVD
signal output.
audio cable is not connected
correctly.
The
audio receiver or TV is turned off.
The
setting of output sound format is
incorrect.
The playback picture has
occasional distortion.
The
Brightess is unstable or
noises are present in the
playback pictures.
The
The DVD video player does
not start playback.
No
An
disc is dirty.
It
is in fast forward or fast reverse
playback.
effect of copy protection.
the PLAY button.
the appropriate video input mode
on the TV so the picture from the DVD
video player appears on the TV screen.
the video cable correctly into
the appropriate jacks.
the correct input mode of the
audio receiver so you can listen to the
sound from the DVD video player.
the audio cable correctly into
the appropriate jacks.
Turn
on the equipment connected with
the audio cable.
Select
Eject
the proper audio setting.
the disc and clean it.
Sometimes
a small amount of picture
distortion may appear. This is not a
malfunction.
the DVD video player directly to
the TV. Avoid connecting the DVD video
player to a VCR or TV/VCR combination
Page
24
18,19
24
18-22
24
42, 56,
60
8
-
Connect
18
disc is inserted.
Insert
24
unplayable disc is inserted.
Insert
a disc.
a playable disc. (Check the disc
type and color system.)
10
The
disc is placed upside down.
Place
The
disc is not placed within the guide.
Place
The
disc is dirty.
Clean
The
parental lock function is set.
Cancel
56, 60,
61
is in the mode of repeat playback,
memeory playback, etc.
the disc with playback side down.
24
the disc correctly inside the guide
on the disc tray.
24
the disc.
the parental lock function or
change the parental lock level.
It
These
-
Buttons do not work.
Power
Press
-
The remote control does not
work properly.
The
Point
15
The
Operate
the remote control within about
15
The
Replace
the batteries with new ones.
15
supply fluctuations or other
abnormalities such as static electricity
may interrupt correct operations.
remote control is not pointed at the
remote sensor of the DVD video player.
batteries in the remote control are
exhausted.
opeations may prevent a proper
progress of the contents.
9
Playback does not follow the
course of the disc’s program.
remote control is too far from the
DVD video player.
64
the power plug securely into
the wall outlet.
and hold the ON/STANDBY
button on the front panel for more than
about 3 seconds. The DVD video player
turns off. Press the button again to turn
it on. If the buttons still do not work,
disconnect the power plug and insert it
into the wall outlet again.
the remote control at the remote
sensor of the DVD video player.
7 m.
Specifications
DVD video player/outputs/supplied accessories
DVD Video Player
Power supply
120 V AC, 60Hz
Power consumption
15W
Mass
1.7kg
External dimensions
430×51×235mm(W/H/D)
Signal system
Standard NTSC
Laser
Semiconductor laser, wavelength 650 nm
Frequency range
DVD linear sound: 48 kHz sampling 20 Hz to 20kHz
96 kHz sampling 20 Hz to 20kHz
Signal-to noise ratio
More than 90dB
Audio dynamic range
More than 80dB
Harmonic distortion
Less than 10%
Wow and flutter
Below measurable level (less than ±0.001%(W.PEAK))
Operating conditions
Temperature: 5℃ to 35℃, Operation status: Horizontal
Others
Outputs
Video output
1.0V(p-p), 75 Ω, negative sync., pin jack × 1
S video output
(Y) 0.7 ± 0.14V, 75 Ω, negative sync., Mini DIN 4-pin × 1
(C) 0.3± 0.06V(p-p), 75 Ω
Component video output
(Y) 0.7±0.14V, 75 Ω, negative sync., pin jack × 1
(PB)/(PR) 0.7±0.14V(p-p),75 Ω, pin jack × 2
Audio output (BITSTREAM/PCM COAXIAL)
0.5V(p-p),75 Ω, pin jack × 1
Audio output (ANALOG)
1.0~2.0V (rms), 10kΩ, pin jack(L,R) × 1
Supplied Accessories
Audio/video cable ..……..............................……..1
Remote control (SE-R0127)..............................…1
Batteries (AAA)……………………............………..2
Stop Return Sheet ................................................1
Owner's Manual (This booklet) .............................1
▪ Designs and specifications are subject to change without notice.
65
Others
LIMITED UNITED STATES WARRANTY DVD PLAYERS- EXCHANGE WARRANTY
Toshiba America Consumer Products, L.L.C. (“TACP”) makes the following limited warranties to original consumers in the United
States. THESE LIMITED WARRANTIES EXTEND TO THE ORIGINAL CONSUMER PURCHASER OR ANY PERSON RECEIVING THIS DVD PLAYER AS A GIFT FROM THE ORIGINAL CONSUMER PURCHASER AND TO NO OTHER PURCHASER OR
TRANSFEREE.
PRODUCTS PURCHASED IN THE U.S.A. AND USED IN CANADA ARE NOT COVERED BY THESE WARRANTIES.
PRODUCTS PURCHASED IN CANADA AND USED IN THE U.S.A. ARE NOT COVERED BY THESE WARRANTIES.
Limited Ninety (90) Day Warranty
TACP warrant this DVD PLAYER and its parts against
defects in materials or workmanship for a period
of ninety (90) days after the date of original retail
purchase . DURING THE FIRST 90 DAYS FROM THE
PURCHASE DATE, TACP WILL EXCHANGE A DEFECTIVE DVD PLAYER WITH A NEW OR REFURBISHED PLAYER WITHOUT CHARGE TO YOU. YOU
MUST CONT ACT TOSHIBA’S CONSUMER SOLUTIONS CENTER FOR INSTRUCTIONS ON HOW TO
PROCESS YOUR IN WARRANTY EXCHANGE REQUEST. THE CONSUMER IS RESPONSIBLE FOR
ALL INBOUND TRANSPOR TATION AND INSURANCE CHARGES FOR THE DVD PLAYER TO THE
EXCHANGE CENTER. DURING THE PERIOD FROM
91 DAYS AND BEYOND, FROM THE PURCHASE
DATE, TACP WILL EXCHANGE A DEFECTIVE DVD
PLAYER WITH A NEW OR REFURBISHED PLAYER
FOR A NOMINALFEE. YOU MUST CONTACT
TOSHIBA’S CONSUMER SOLUTIONS CENTER
FOR INSTRUCTIONS ON HOW TO PROCESS
YOUR EXCHANGE REQUEST. THE CONSUMER IS
RESPONSIBLE FOR ALL INBOUND TRANSPORTATION AND INSURANCE CHARGES FOR THE DVD
PLAYER TO THE EXCHANGE CENTER.
*Rental Units
The warranty for rental units begins with the first rental
or thirty (30) days from the date of shipment to the
rental firm, whichever comes first.
*Commercial Units
DVD PLAYERs sold and used for commercial purposes have a limited ninety (90) day warranty for all
parts, labor.
66
Owner’s Manual and Demographic Card
You should read this owner’s manual thoroughly
before operating this DVD PLAYER. You should complete and mail the enclosed Demographic card within
ten days after you, or the person who has given you
this product as a gift, purchased this DVD PLAYER.
This is one way to enable TACP to provide you with
better customer service and improved products. Faiure
to return the Demographic card will not affect your
rights under this warranty.
Your Responsibility
THE ABOVE WARRANTIES ARE SUBJECT TO THE
FOLLOWING CONDITIONS:
(1) You must provide your bill of sale or other proof of
purchase.
(2) All warranty servicing of this DVD PLAYER must
be made by an Authorized TACP Service Station.
(3) The warranties from TACP are effective only if the
DVD PLAYER is purchased and operated in the
U.S.A. or Puer to Rico.
(4) Labor service charges for set installation, set up,
adjustment of customer controls and installation
or repair of antenna systems are not covered by
these warranties. Reception problems caused by
inadequate antenna systems are your responsibility.
(5) Warranties extend only to defects in materials or
workmanship as limited above and do not extend
to any DVD PLAYER or par ts which have been
lost or discarded by you or to damage to DVD
PLAYER or parts caused by misuse, accident, Acts
of God, such as lightning or fluctuations inelectric
power, improper installation, improper maintenance or use in violation of instructions furnished
by TACP; or to units which have been modified or
had the serial number removed, altered, defaced
or rendered illegible.
How to Obtain Warranty Services
If, after following all of the operating instructions in this
manual and checking the section “Troubleshooting”,
you find that service is needed:
(1) Fo r instructions on how to obtain warranty service
for exchange program DVD Players, contact
TACP’S toll free Call Center at 1-866-583-7353.
(2) Include your bill of sale or other proof of purchase
along with the DVD player, when sending it to the
Authorized TACP Service Station SPECIFIED by
TACPs Call Center. You must pay for all transportation and insurance charges for the DVD Product
to and from the Service Station.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL
RIGHTS , AND YOU MAY ALSO HAVE OTHER
RIGHTS WHICH MAY VARY FROM STATE TO
STATE IN THE U.S.A. SOME STATES OF THE U.S.A.
DO NOT ALLOW LIMITATIONS ON HOW LONG AN
IMPLIED WARRANTY LASTS , WHEN AN ACTION
MAY BE BROUGHT , OR THE EXCLUSION OR
LIMITATION OF INCIDENTAL OR CONSEQUENTIAL
DAMAGES, SO THE AFOREMENTIONED LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU
UNDER SUCH CIRCUMSTANCES.
For additional information, visit TACP’s web site:
www.tacp.toshiba.com
Others
ALL WARRANTIES IMPLIED BY THE LAW OF ANY
STATE OF THE U.S.A., INCLUDING THE IMPLIED
WARRANTIES OF MERCHANT ABILITY AND
FITNESS FOR A PA R TICULAR PURPOSE, ARE
EXPRESSLY LIMITED TO THE DURATION OF THE
LIMITED WARRANTIES SET FOR THE ABOVE.
WITH THE EXCEPTION OF ANY WARRANTIES IMPLIED BY THE LAW OF ANY STATE OF THE U.S.A.
AS HEREBY LIMITED, THE FOREGOING WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER
WARRANTIES, GUARANTEES, AGREEMENTS AND
SIMILAR OBLIGATIONS OF TACP OR THI WITH
RESPECT TO THE REP AIR OR REPLACEMENT
OF ANY PARTS. IN NO EVENT SHALL TACP BE
LIABLE FOR CONSEQUENTIAL OR INCIDENTAL
DAMAGES.
No person, agent, distributor, dealer or company is
authorized to change , modify or extend the terms of
these warranties in any manner whatsoever. The time
within which action must be commenced to enforce
any obligation of TACP ar ising under this warranty
or under any law of the United States or of any state
thereof is hereby limited to 90 days from the date you
discovered or should have discovered, the defect. This
limitation does not apply to implied warranties arising
under the law of any state of the U.S.A.
67
TOSHIBA
Printed in China
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement