Roland HP201 Musical Instrument User Manual

Roland HP201 Musical Instrument User Manual
*
0
4
5
6
4
7
2
3
04564723
-
0
1
*
07-01-1N
DIC449
Cover1,4
HP201_e.book 3 ページ 2007年1月15日 月曜日 午後5時37分
WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
ATTENTION: RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated “dangerous voltage” within the
product’s enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the
literature accompanying the product.
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS.
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
WARNING - When using electric products, basic precautions should always be followed, including the following:
1.
2.
3.
4.
5.
6.
7.
8.
9.
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with a dry cloth.
Do not block any of the ventilation openings. Install in
accordance with the manufacturers instructions.
Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades with
one wider than the other. A grounding type plug has two
blades and a third grounding prong. The wide blade or the
third prong are provided for your safety. If the provided plug
does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the
point where they exit from the apparatus.
11. Only use attachments/accessories specified by the
manufacturer.
12. Use only with the cart, stand, tripod, bracket,
or table specified by the manufacturer, or
sold with the apparatus. When a cart is used,
use caution when moving the cart/apparatus
combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when
unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing
is required when the apparatus has been damaged in any
way, such as power-supply cord or plug is damaged, liquid
has been spilled or objects have fallen into the apparatus,
the apparatus has been exposed to rain or moisture, does
not operate normally, or has been dropped.
For the U.K.
IMPORTANT: THE WIRES IN THIS MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE.
BLUE:
NEUTRAL
BROWN: LIVE
As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying
the terminals in your plug, proceed as follows:
The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK.
The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED.
Under no circumstances must either of the above wires be connected to the earth terminal of a three pin plug.
Before using this unit, carefully read the sections entitled: “IMPORTANT SAFETY INSTRUCTIONS,”
“USING THE UNIT SAFELY” (p. 4), and “Important Notes” (p. 7). These sections provide important
information concerning the proper operation of the unit. Additionally, in order to feel assured that you
have gained a good grasp of every feature provided by your new unit, owner’s manual should be read
in its entirety. The manual should be saved and kept on hand as a convenient reference.
Copyright © 2007 ROLAND CORPORATION
All rights reserved. No part of this publication may be reproduced in any form
without the written permission of ROLAND CORPORATION.
HP201_e.book 4 ページ 2007年1月15日 月曜日 午後5時37分
USING THE UNIT SAFELY
The
symbol alerts the user to important instructions or
warnings.The specific meaning of the symbol is
determined by the design contained within the triangle.
In the case of the symbol at left, it is used for general
cautions, warnings, or alerts to danger.
Used for instructions intended to alert the
user to the risk of death or severe injury
should the unit be used improperly.
Used for instructions intended to alert the
user to the risk of injury or material
damage should the unit be used
improperly.
The
symbol alerts the user to items that must never
be carried out (are forbidden). The specific thing that
must not be done is indicated by the design contained
within the circle. In the case of the symbol at left, it
means that the unit must never be disassembled.
* Material damage refers to damage or
other adverse effects caused with
respect to the home and all its
furnishings, as well to domestic animals
or pets.
The ● symbol alerts the user to things that must be
carried out. The specific thing that must be done is
indicated by the design contained within the circle. In
the case of the symbol at left, it means that the powercord plug must be unplugged from the outlet.
Do not disassemble or modify
Use only the included power cord
002a
008e
Do not disassemble or modify this device.
......................................................................................
Do not repair or replace parts
003
Never attempt to repair this device or replace
parts. If repair or part replacement should become
necessary, you must contact your dealer or a
Roland service center.
......................................................................................
Do not use or store in the following types of
locations
004
• Locations of extremely high temperature (such as
in direct sunlight, near heating equipment, or on
a device that generates heat)
• Near moisture (such as in a bathroom, near a
sink, or on a wet floor) or in locations of high
humidity
• Locations exposed to rain
• Locations of excessive dust
• Locations subject to heavy vibration
......................................................................................
Do not place in an unstable location
007
Do not place this device on an unstable stand or a
tilted surface. You must place it in a stable and
level location.
......................................................................................
Connect the power cord to an outlet of the correct
voltage
008a
You must connect the power cord to an AC outlet
of the correct voltage as marked on the device.
......................................................................................
4
You must use only the power cord included with the
device. Do not use the included power cord with
any other device.
......................................................................................
Do not bend the power cord or place heavy objects
on it
009
Do not bend the power cord excessively, or place
heavy objects on the power cord. Doing so will
damage the power cord, and may cause short
circuits or faulty connections, possibly resulting in
fire or electrical shock.
......................................................................................
Do not share an outlet with an unreasonable
number of other devices
015
Do not connect excessive numbers of electrical
devices to a single power outlet. In particular,
when using a power strip, exceeding the rated
capacity (watts/amps) of the power strip may
cause heat to be generated, possibly melting the
cable.
......................................................................................
Avoid extended use at high volume
010
This device, either by itself or used in conjunction
with headphones, amps, and/or speakers, is
capable of producing volume levels that can cause
permanent hearing damage. If you experience
impaired hearing or ringing in your ears,
immediately stop using the device and consult a
medical specialist.
......................................................................................
HP201_e.book 5 ページ 2007年1月15日 月曜日 午後5時37分
USING THE UNIT SAFELY
Do not insert foreign objects
Place in a well ventilated location
011
101a
Never allow foreign objects (flammable objects,
coins, wires, etc.) to enter this device.
This can cause short circuits or other malfunctions.
......................................................................................
Turn off the power if an abnormality or
malfunction occurs
012a
If any of the following should occur, immediately
turn off the power, disconnect the power cord from
the AC outlet, and contact your dealer or a service
center to have the device serviced.
• The power cord is damaged
• The device produces smoke or an unusual smell
• A foreign object enters the device, or liquid
spills into the device
• The device becomes wet (by rain, etc.)
• An abnormality or malfunction occurs in the device
......................................................................................
When using this device, ensure that it is placed in
a well ventilated location.
......................................................................................
Grasp the plug when connecting or disconnecting
the power cord
102b
When connecting or disconnecting the power cord
to/from an AC outlet or the device itself, you must
grasp the plug, not the cord.
......................................................................................
Periodically wipe the dust off the power cord plug
103a
From time to time, you should unplug the power
cord from the AC outlet and use a dry cloth to wipe
the dust off of it. You should also unplug the power
cord from the AC outlet if you will not be using the
device for an extended period of time. Dust or dirt
that accumulates between the power cord plug and
the AC outlet can cause a short circuit, possibly
resulting in fire.
......................................................................................
Do not allow children to use without supervision
Manage cables for safety
013
104
Do not drop or subject to strong impact
106
In households with children, take particular care
against tampering. If children are to use this device,
they must be supervised or guided by an adult.
......................................................................................
014
Do not use overseas
If you wish to use this device overseas, please
contact your dealer or a service center.
......................................................................................
Do not place containers of water on the device
026
Do not stand or place heavy objects on this device
Do not drop this device or subject it to strong
impact.
......................................................................................
016
Ensure that the connected cables are organized
and managed in a safe manner. In particular,
place the cables out of reach of children.
......................................................................................
Do not place containers of water (such as a flower
vase) or drinks on the device. Nor should you
place containers of insecticide, perfume, alcoholic
liquids, nail polish, or spray cans on the device.
Liquids that spill into the device may cause it to
malfunction, and may cause short circuits or faulty
operation.
......................................................................................
Do not stand on this device, or place heavy objects
on it.
......................................................................................
Do not connect or disconnect the power cord with
wet hands
107b
Do not connect or disconnect the power cord to the
device or AC outlet while holding the power cord
plug with wet hands.
......................................................................................
Cautions when moving this device
108d
1
2
When moving this device, please check the
following cautions. Then, make sure that at least
two persons work together in lifting and carrying
the device, all the while making sure to keep it
level. When doing so, be careful not to pinch your
hands or drop the device on your feet.
• Check whether the screws fastening the device
to its stand have become loose. If they are loose,
tighten them firmly.
• Disconnect the power cord.
3
• Disconnect external devices.
4
• Raise the adjuster of the stand (p. 14).
5
• Close the lid.
• Remove the music rest.
......................................................................................
6
5
HP201_e.book 6 ページ 2007年1月15日 月曜日 午後5時37分
USING THE UNIT SAFELY
Unplug the power cord from the AC outlet before
cleaning
109a
Before you clean the device, turn off the power and
unplug the power cord from the AC outlet (p. 12).
......................................................................................
If there is a possibility of lightning strike,
disconnect the power cord from the AC outlet
110a
If there is a possibility of lightning strike,
immediately turn off the power and disconnect the
power cord from the AC outlet.
......................................................................................
Cautions when opening/closing the lid
116
Be careful when opening/closing the lid so you do
not get your fingers pinched (p. 12). Adult
supervision is recommended whenever small
children use the unit.
......................................................................................
Keep small items out of the reach of children
118c
To prevent small items such as the following from
being swallowed accidentally, keep them out of the
reach of children.
• Included items
•Screws for assembling the stand
•Wing nut for headphone hook
• Removed parts
•Music rest attachment screws
......................................................................................
6
HP201_e.book 7 ページ 2007年1月15日 月曜日 午後5時37分
Important Notes
291b
In addition to the items listed under “IMPORTANT SAFETY INSTRUCTIONS” and “USING THE UNIT SAFELY” on pages 3 and 4–6,
please read and observe the following:
Power Supply
301
• Do not connect this unit to same electrical outlet that is
being used by an electrical appliance that is controlled by
an inverter (such as a refrigerator, washing machine,
microwave oven, or air conditioner), or that contains a
motor. Depending on the way in which the electrical
appliance is used, power supply noise may cause this unit
to malfunction or may produce audible noise. If it is not
practical to use a separate electrical outlet, connect a
power supply noise filter between this unit and the electrical
outlet.
307
• Before connecting this unit to other devices, turn off the
power to all units. This will help prevent malfunctions and/
or damage to speakers or other devices.
308
• Although the LEDs are switched off when the POWER
switch is switched off, this does not mean that the unit has
been completely disconnected from the source of power. If
you need to turn off the power completely, first turn off the
POWER switch, then unplug the power cord from the
power outlet. For this reason, the outlet into which you
choose to connect the power cord’s plug should be one that
is within easy reach and readily accessible.
Placement
351
• Using the unit near power amplifiers (or other equipment
containing large power transformers) may induce hum. To
alleviate the problem, change the orientation of this unit; or
move it farther away from the source of interference.
352a
• This device may interfere with radio and television
reception. Do not use this device in the vicinity of such
receivers.
352b
• Noise may be produced if wireless communications
devices, such as cell phones, are operated in the vicinity of
this unit. Such noise could occur when receiving or
initiating a call, or while conversing. Should you
experience such problems, you should relocate such
wireless devices so they are at a greater distance from this
unit, or switch them off.
354b
• Do not expose the unit to direct sunlight, place it near
devices that radiate heat, leave it inside an enclosed
vehicle, or otherwise subject it to temperature extremes.
Also, do not allow lighting devices that normally are used
while their light source is very close to the unit (such as a
piano light), or powerful spotlights to shine upon the same
area of the unit for extended periods of time. Excessive
heat can deform or discolor the unit.
355b
• When moved from one location to another where the
temperature and/or humidity is very different, water
droplets (condensation) may form inside the unit. Damage
or malfunction may result if you attempt to use the unit in
this condition. Therefore, before using the unit, you must
allow it to stand for several hours, until the condensation
has completely evaporated.
356
• Do not allow rubber, vinyl, or similar materials to remain on
the unit for long periods of time. Such objects can discolor
or otherwise harmfully affect the finish.
358
• Do not allow objects to remain on top of the keyboard. This
can be the cause of malfunction, such as keys ceasing to
produce sound.
359
• Do not paste stickers, decals, or the like to this instrument.
Peeling such matter off the instrument may damage the
exterior finish.
Maintenance
401b
• To clean the unit, use a dry, soft cloth; or one that is slightly
dampened. Try to wipe the entire surface using an equal
amount of strength, moving the cloth along with the grain of
the wood. Rubbing too hard in the same area can damage
the finish.
Addition
• If water droplets should adhere to this device, immediately
wipe them off using a soft dry cloth.
402
• Never use benzine, thinners, alcohol or solvents of any
kind, to avoid the possibility of discoloration and/or
deformation.
403
• The pedals of this unit are made of brass.
Brass eventually darkens as the result of the natural
oxidization process. If the brass becomes tarnished, polish
it using commercially available metal polisher.
Repairs and Data
452
• Please be aware that all data contained in the unit’s
memory may be lost when the unit is sent for repairs.
Important data should always be backed up in another
MIDI device (e.g., a sequencer), or written down on paper
(when possible). During repairs, due care is taken to avoid
the loss of data. However, in certain cases (such as when
circuitry related to memory itself is out of order), we regret
that it may not be possible to restore the data, and Roland
assumes no liability concerning such loss of data.
7
HP201_e.book 8 ページ 2007年1月15日 月曜日 午後5時37分
Important Notes
Additional Precautions
551
• Please be aware that the contents of memory can be
irretrievably lost as a result of a malfunction, or the
improper operation of the unit. To protect yourself against
the risk of loosing important data, we recommend that you
periodically save a backup copy of important data you
have stored in the unit’s memory in another MIDI device
(e.g., a sequencer).
552
• Unfortunately, it may be impossible to restore the contents
of data that was stored in the unit’s memory once it has
been lost. Roland Corporation assumes no liability
concerning such loss of data.
553
• Use a reasonable amount of care when using the unit’s
buttons, knobs, or other controls; and when using its jacks
and connectors. Rough handling can lead to malfunctions.
556
• When connecting / disconnecting all cables, grasp the
connector itself—never pull on the cable. This way you will
avoid causing shorts, or damage to the cable’s internal
elements.
557
• A small amount of heat will radiate from the unit during
normal operation.
558a
• To avoid disturbing your neighbors, try to keep the unit’s
volume at reasonable levels. You may prefer to use
headphones, so you do not need to be concerned about
those around you (especially when it is late at night).
559b
• When you need to transport the unit, pack it in shockabsorbent material. Transporting the unit without doing so
can cause it to become scratched or damaged, and could
lead to malfunction.
560
• Do not apply undue force to the music rest while it is in use.
562
• Some connection cables contain resistors. Do not use
cables that incorporate resistors for connecting to this unit.
The use of such cables can cause the sound level to be
extremely low, or impossible to hear. For information on
cable specifications, contact the manufacturer of the cable.
565
• Before opening or closing the keyboard lid, always make
sure that no pets or other small animals are located on top
of the instrument (in particular, they should be kept away
from the keyboard and its lid). Otherwise, due to the
structural design of this instrument, small pets or other
animals could end up getting trapped inside it. If such a
situation is encountered, you must immediately switch off
the power and disconnect the power cord from the outlet.
You should then consult with the retailer from whom the
instrument was purchased, or contact the nearest Roland
Service Center.
8
203
* GS (
) is a registered trademark of Roland
Corporation.
Add
* XG lite (
) is a registered trademark of Yamaha
Corporation.
HP201_e.book 9 ページ 2007年1月15日 月曜日 午後5時37分
Contents
USING THE UNIT SAFELY ............................. 4
Recording Your Performance...................... 30
Recording............................................................... 30
Important Notes .......................................... 7
Main Features ........................................... 10
Panel Descriptions ..................................... 11
Playing Back the Recorded Performance..................... 31
Erasing Recorded Performances ................................ 31
Changing Various Settings ......................... 32
Tuning to Other Instruments’ Pitches (Master Tuning) .... 32
Control Panel ..........................................................11
Lowering/Raising the Standard Pitch .................... 32
Bottom Panel/Rear Panel ..........................................11
Setting the Standard Pitch to 440.0 Hz ................. 32
Setting the Standard Pitch to 442.0 Hz ................. 32
Before You Start Playing............................ 12
Changing the Temperament...................................... 33
Connecting the Pedal Cord .......................................12
Setting the Tonic................................................. 33
Connecting the Power Cord ......................................12
Opening/Closing the Lid ..........................................12
Changing the Damper Pedal’s Resonance
(Damper Resonance)................................................ 34
Setting Up the Music Rest .........................................12
Setting the Tuning Curve (Stretch Tuning) .................... 34
Connecting Headphones ..........................................13
Disabling Everything Except Piano Play (Panel Lock) .... 35
Using the Headphone Hook.................................13
Using the V-LINK function ......................................... 35
Turning the Power On and Off ..................................13
Adjusting the Sound’s Volume ...................................14
Remembering the Settings Even when the Power is
Turned Off (Memory Backup) .................................... 36
About the Pedals .....................................................14
Restoring the Original Default Settings (Factory Reset) .. 36
About the Adjuster ...................................................14
Enjoying the Internal Songs ....................... 15
Connecting External Devices....................... 37
Connecting to Audio Equipment ................................ 37
Connecting MIDI Devices ......................................... 38
Performance ............................................. 16
What’s MIDI? .................................................... 38
Performing with a Variety of Sounds ..........................16
MIDI Send Channel Settings ................................ 38
Playing Two Sounds Together (Dual Play) ...................17
Switching Local Control On and Off ..................... 39
Adjusting the Volume Balance in Dual Play
(Dual Balance) ...................................................18
Sending Recorded Performance Data to a MIDI
Device (Composer Out)....................................... 39
Changing the Brightness of the Sound (Brilliance) ........19
Connecting to a Computer........................................ 40
Adding Liveliness to the Sound (Dynamics)..................19
Changing the USB Driver Settings ........................ 40
Playing Sounds When the Keys Are Released
(Key Off Resonance) ................................................20
Appendices ............................................... 41
Adding Reverberation to the Sound (Reverb) ...............21
Troubleshooting....................................................... 41
Changing the Depth of the Reverb Effect................21
Tone List ................................................................. 42
Adjusting the Keyboard Touch (Key Touch) .................22
Internal Song List ..................................................... 43
Transposing the Key of the Keyboard (Transpose) ........23
Easy Operation List.................................................. 44
Splitting the Keyboard Into Two Sections for Four-Hand
Performances (Twin Piano) ........................................24
MIDI Implementation Chart ....................................... 46
Changing the Way in Which the Sound is Heard
(Twin Piano Mode) .............................................25
Main Specifications ................................................. 47
Index ........................................................ 48
Using Metronome ....................................................26
Sounding the Metronome ....................................26
Changing the Beat of Metronome .........................26
Changing the Metronome Volume ........................27
Changing the Metronome Tempo .........................27
9
HP201_e.book 10 ページ 2007年1月15日 月曜日 午後5時37分
Main Features
Thank you, and congratulations on your choice of the Roland Digital Piano HP201.
To ensure that you obtain the maximum enjoyment and take full advantage of the HP201’s functionality, please
read this owner’s manual carefully.
Piano Sounds with Rich Resonance and Wide Expressive Range
• This instrument features a piano sound generator that utilizes stereo sampling, so it is capable of faithfully
recreating the sound of a high-quality concert grand piano, realistically reproducing even the finest details,
including the sound of the hammers striking the strings. With a maximum polyphony of 128 notes, it has ample
capability even for performances that make full use of pedaling.
The Playing Feel of a Grand Piano
• The Progressive Hammer Action II (PHA II) keyboard gives you a weighty playing feel in the low register while
becoming lighter in the high register, replicating the authentic feel of a piano.
• The pedal position is detected smoothly, allowing you to vary the effect by the changing the depth to which
you press the pedal. You can take advantage of the way in which subtle differences in pedaling will affect the
sound.
A Compact Cabinet that Fits Anywhere
• The newly designed cabinet projects a sense of elegant craftsmanship. It can be placed nearly anywhere, and
does not occupy excessive space.
• In addition to a sliding keyboard lid that stores inside the instrument, there’s a headphone hook for conveniently
storing your headphones when not using them.
Functionality to Assist Your Practicing
• There’s a metronome, a recorder function, and built-in song, so you can experience the kind of piano lessons
that are possible only with a digital piano.
USB (MIDI) Connector
• There’s a USB (MIDI) connector for connection to your computer, allowing you to play the HP201 using data
from your computer, or to use your computer for even more versatile music production and editing.
The HP201’s sound generator supports the GM2 system, GS format, and XG lite, allowing you to enjoy
impressive ensemble performances by using your computer or sequencer to play back commercially available
music in these formats.
10
HP201_e.book 11 ページ 2007年1月15日 月曜日 午後5時37分
Panel Descriptions
Control Panel
Rear Panel
Bottom Panel
1
Pedal Connector
2
AC Inlet
1
Pedal Connector
2
Connect the pedal cord to this connector (p. 12).
AC Inlet
Connect the supplied power cord here (p. 12).
Control Panel
3
4
4
5
6
7
8
6
[VOLUME] Knob
Adjusts the overall volume level (p. 14).
5
[TONE] Button
Used to choose the tone played by the keyboard (p. 16).
[SONG] Button
Plays the internal songs (p. 15) or the song you recorded
(p. 31). If you simultaneously press the [SONG] button
and [METRONOME] button, you’ll enter recordingstandby mode (p. 30).
7
[METRONOME] Button
Turns the metronome on/off (p. 26).
8
3
[REVERB/KEY TOUCH] Button
Adds reverberation to the sound (p. 21).
Modifies the playing feel of the keyboard (p. 22).
[POWER] Switch
Turns the power on/off (p. 13).
Bottom Panel/Rear Panel
10 MIDI Out/In Connectors
11
Connect to external MIDI devices to exchange
performance data (p. 38).
10
9
9
11 USB (MIDI) Connector
You can connect this to your computer for transferring
performance data (p. 40).
12
13
Phones Jacks
You can connect headphones to these jacks (p. 13).
12 Input Jacks
These jacks can be connected to another sound
generating device or an audio device, so that the sound
of that device will be output from the HP201’s speakers
(p. 37).
13 Output Jacks
Allows you to output the piano’s sound to sound
reinforcement equipment to obtain a more powerful
sound. These can also be connected to a tape recorder or
other recording device to record a performance (p. 37).
11
HP201_e.book 12 ページ 2007年1月15日 月曜日 午後5時37分
Before You Start Playing
Connecting the Pedal Cord
Setting Up the Music Rest
1. Connect the pedal cord to the Pedal connector on the
1. Insert the included music rest attachment screws into
bottom panel of the HP201, at the rear.
fig.00-01
the screw holes on top of the HP201, and tighten the
screws slightly.
fig.00-03
Connecting the Power Cord
1. Insert the included power cord into the AC inlet on
the bottom panel of the HP201, at the rear.
2. Put the music rest between the screws and the
HP201’s body.
2. Plug the power cord into a power outlet.
NOTE
Be sure to use the supplied power cord.
fig.00-02
3. While supporting the music rest with one hand,
secure it in place by turning the screws.
Opening/Closing the Lid
To open the lid, use both hands to lift it lightly, and
slide it away from yourself.
To close the lid, pull it gently toward yourself, and
lower it softly after it has been fully extended.
fig.00-05
When attaching the music rest, support it firmly with one
hand to make sure that you don’t drop it. Be careful, so
you don’t get your fingers pinched.
4. To remove the music rest, support it with one hand
while loosening the screws.
After removing the music rest, don’t forget to retighten the
screws.
NOTE
Do not apply excessive force to the installed music rest.
NOTE
NOTE
When opening and closing the lid, be careful not to let
your fingers get caught. If small children will be using the
HP201, adult supervision should be provided.
NOTE
If you need to move the piano, make sure the lid is closed
first to prevent accidents.
12
Be sure to use the supplied screws for attaching the music
rest.
NOTE
Before moving the HP201, be sure to remove the music
rest to prevent accidents.
HP201_e.book 13 ページ 2007年1月15日 月曜日 午後5時37分
Before You Start Playing
Connecting Headphones
Turning the Power On and Off
The HP201 has two jacks for plugging in headphones.
This allows two people to listen through headphones
simultaneously, making it very useful for lessons and when
performing piano pieces for four hands. Additionally, this
allows you to play without having to worry about bothering
others around you, even at night.
1. Plug the headphones into the Phones jack located at
the bottom left of the piano.
Connecting headphones will automatically mute the sound
from the internal speakers. The headphone volume is
adjusted by the [VOLUME] knob of the HP201 (p. 14).
fig.00-04.e
NOTE
Once the connections have been completed, turn on
power to your various devices in the order specified.
By turning on devices in the wrong order, you risk causing
malfunction and/or damage to speakers and other
devices.
1. To turn the power on, turn the [VOLUME] knob all
the way down, and then press the [POWER] switch.
The power will turn on, and the indicator of the [TONE]
button will light.
After a few seconds, you will be able to play the
keyboard to produce sound.
Use the [VOLUME] knob to adjust the volume.
NOTE
This unit is equipped with a protection circuit. A brief
Phones jack x 2
interval (a few seconds) after power up is required before
the unit will operate normally.
NOTE
fig.00-06.e
Use Stereo headphones.
Some notes on using headphones
• To prevent damage to the cord, handle the headphones
only by the headset or the plug.
• Connecting the headphones when the volume of
connected equipment is turned up may result in damage
to the headphones. Lower the volume on the HP201
before plugging in the headphones.
• Listening at excessively high volume levels will not only
damage the headphones, but may also cause hearing
loss. Use the headphones at a moderate volume level.
■ Using the Headphone Hook
Whenever you are not using the headphones, you can hang
them on the headphone hook at the lower left of the HP201.
Attaching the Headphone Hook
Press and twist the headphone hook included with the HP201
into the hole in the bottom of the HP201 (refer to the figure
below). Turn the wing nut of headphone hook to secure the
headphone hook.
Turning the Power Off
1. To turn the power off, turn the [VOLUME] knob all
the way to the left, and press the [POWER] switch.
The indicators for all buttons will go out, and the power
will turn off.
NOTE
If you need to turn off the power completely, first turn off
the [POWER] switch, then unplug the power cord from the
power outlet. Refer to “Power Supply” (p. 7).
Hole
Wing Nut
Headphone Hook
13
HP201_e.book 14 ページ 2007年1月15日 月曜日 午後5時37分
Before You Start Playing
Adjusting the Sound’s Volume
About the Adjuster
1. Turn the [VOLUME] knob to adjust the overall
If you feel that the pedal is unstable (for example if you’ve
moved the HP201 to a different location), you can adjust the
volume.
adjuster located on the bottom of the pedals as follows.
fig.00-07.e
The volume
decreases
The volume
increases
• Turn the adjuster to lower it until the adjuster is in firm
contact with the floor. The pedal may be damaged if there
is a gap between the adjuster and the floor. In particular,
when you’ve placed the HP201 on carpet, you must turn
the adjuster until it is pressing firmly against the floor.
About the Pedals
The pedals perform the following operations. You’ll use them
mainly when playing piano.
Adjuster
Damper Pedal
Soft Pedal
Sostenuto Pedal
Damper Pedal (right pedal)
While this pedal is held down, notes will be sustained for an
extended time even if you release your fingers from the
keyboard.
On an acoustic piano, holding down the damper pedal will
cause the strings for notes other than the ones you actually
play to vibrate in sympathy with what you’ve played,
producing a rich resonance. The HP201 simulates this
sympathetic vibration (damper resonance).
If the adjuster is difficult to turn, have one person lift either
the left or right side of the stand to make it easier for
another person to turn the adjuster and make the
adjustment.
NOTE
After adjusting the adjuster, press the pedals, and if the
front board moves, turn the adjuster further so that it
makes firm contact with the floor.
NOTE
Always readjust the adjuster after moving the piano.
NOTE
You can change the amount of resonance applied with
the damper pedal. Refer to “Changing the Damper
Pedal’s Resonance (Damper Resonance)” (p. 34).
Sostenuto Pedal (center pedal)
The notes you are pressing when this pedal is depressed will
be sustained.
Soft Pedal (left pedal)
This pedal is used to make the sound softer.
14
HP201_e.book 15 ページ 2007年1月15日 月曜日 午後5時37分
Enjoying the Internal Songs
The HP201 comes with 65 piano songs onboard.
The songs are played back continuously in sequence.
For more details, refer to
“Internal Song List” (p. 43).
fig.panel1-2
1
4
6
9 11 13
16 18
21 23 25
57 59 61
2 3 5 7 8 10 12 14 15 17 19 20 22 24 26 . . .
C1
C2
64
. . . 58 60 62 63 65
C3
C6
The Song You Record
1.
While holding down the [SONG] button, press the key that
corresponds to the song you wish to hear.
The built-in songs are assigned consecutively, starting with the B 0 key.
* The song you record (p. 30) is assigned to the leftmost key (A0) of the keyboard.
You can also play back a song
by simply pressing the [SONG]
button. In this case, playback
The song will begin playing when you press the key. When the selected song has
will begin with the song you
finished playing, the next song will begin playing.
selected most recently by
pressing a key.
When the last song has finished playing, playback will begin again from the first song.
However, if you’ve recorded a song, that song will play before the first built-in song
begins playing.
If there is a song you’ve
recorded, the [TONE] button’s
indicator will blink while you
Stopping the playback
2.
hold down the [SONG] button.
Press the [SONG] button, getting the button to go dark.
Playback will stop.
The next time you press the [SONG] button, the song you selected most recently by
pressing a key will play.
If there’s no song that you’ve
recorded, the first of the built-in
songs will play when you press
the [SONG] button and then
the A0 key.
• You can change the tempo of the song while it plays. The procedure is the
same as in “Changing the Metronome Tempo” (p. 27).
• You can make the metronome (p. 26) sound while the song plays.
15
HP201_e.book 16 ページ 2007年1月15日 月曜日 午後5時37分
Performance
Performing with a Variety of Sounds
The HP201 contains 20 different internal tones.
You can also select a tone by pressing the [TONE] button and a key to which a tone
For more details, refer to “Tone
is assigned.
List” (p. 42).
The “Grand Piano 1” tone is selected when the instrument is turned on.
fig.panel2-1
1
A0 B0 C1 D1 E1 F1 G1 A1 B1 C2 D2 E2
2
1.
Press the [TONE] button.
You can also switch sounds by
The button’s indicator will blink.
2.
holding down the [TONE]
Press a key to which a tone is assigned.
The [TONE] button’s indicator will change from blinking to lit.
Keys to which tones are assigned:
button and pressing a key to
which a sound is assigned.
A0–E2 keys
The tone you’ve selected is heard when you finger the keyboard.
Tone
Grand Piano1
Key
Pressed
A0
B 0
Grand Piano2
B0
Honky-tonk
C1
C 1
Harpsichord
Pop E.Piano
E1
FM E.Piano
F1
F 1
ChurchOrgan2
B1
Nason flute 8'
C2
C 2
Ballad Organ
16
Aerial Choir
Soft Pad
Morning Lite
Harp
Piano + Strings
D2
E 2
E2
NOTE
While you’re selecting a sound,
A1
B 1
Combo Jazz Organ
Orchestra Strings
G1
A 1
ChurchOrgan1
Rich Strings
D1
E 1
Vibraphone
Tone
Piano + Choir
playing the keyboard won’t
produce sound.
HP201_e.book 17 ページ 2007年1月15日 月曜日 午後5時37分
Performance
Playing Two Sounds Together (Dual Play)
Simultaneously playing two tones when one key is pressed is called “Dual play.”
fig.panel2-5
1
A0 B0 C1 D1 E1 F1 G1 A1 B1 C2 D2 E2
You can also switch sounds by
holding down the [TONE]
2
button and simultaneously
pressing two keys to which
1.
sounds are assigned.
Press the [TONE] button.
The button’s indicator will blink.
2.
Simultaneously press a white key and black key to which tones are
assigned.
The [TONE] button’s indicator will change from blinking to lit.
The black keys are assigned to sounds that are suitable for layering with the sounds
You can also use Dual Play by
combining tones that are
assigned to two white keys or
two black keys.
assigned to white keys.
Tone
Grand Piano1
Key
Pressed
A0
B 0
Grand Piano2
B0
Honky-tonk
C1
C 1
Harpsichord
FM E.Piano
B1
Nason flute 8'
C2
C 2
Harp
NOTE
Piano + Strings
You can’t use Dual Play mode
while using Twin Piano function
D2
E 2
3.
Morning Lite
A1
ChurchOrgan2
Ballad Organ
Soft Pad
G1
B 1
Combo Jazz Organ
Aerial Choir
F1
A 1
ChurchOrgan1
Orchestra Strings
E1
F 1
Vibraphone
Rich Strings
D1
E 1
Pop E.Piano
Tone
Piano + Choir
(p. 24).
E2
To cancel Dual play, press the [TONE] button and then press a key to
which a sound is assigned.
17
HP201_e.book 18 ページ 2007年1月15日 月曜日 午後5時37分
Performance
■ Adjusting the Volume Balance in Dual Play
(Dual Balance)
You can change the volume balance between the two layered sounds in Dual play.
You can adjust the dual
balance in 17 steps.
fig.panel2-2
While holding down
the [TONE] button...
When using Dual play, the tones are handled as follows according to the
combination of keys you pressed.
1.
White key and black key
White key and white key, or
black key and black key
White key: Tone 1
Left key:
Black key: Tone 2
Right key: Tone 2
Tone 1
Hold down the [TONE] button and press the “C ” or “E ” keys of
any octave above C 3.
You can also adjust the dual
The volume balance changes.
“E ” keys of any octave above
• Hold down the [TONE] button and press the “C ” key of any octave above C 3
to lower the volume of the Tone 2.
• Holding down the [TONE] button and pressing the “E ” key of any octave above
C 3 raises the volume of the Tone 2.
2.
18
To return to the original volume balance, hold down the [TONE]
button and press both the “C ” and “E ” keys of any octave above
C 3 simultaneously.
balance by using the “C ” and
C 3.
HP201_e.book 19 ページ 2007年1月15日 月曜日 午後5時37分
Performance
Changing the Brightness of the Sound (Brilliance)
You can adjust the brightness of the sound.
You can use the Memory
Backup function to store this
setting in internal memory (p.
36).
C4 D4 E4 F4 G4 A4 B4
A0
1.
Hold down the [TONE] button and press one of the keys from “C4” to
“B4” to adjust the brightness of the sound.
This is set to “0” when the
HP201 is shipped from the
Key Pressed
Setting
C4
-3
D4
-2
E4
-1
F4
0
G4
+1
A4
+2
B4
+3
Explanation
factory.
Mellow sound (three levels).
Normal sound.
Bright sound (three levels).
Adding Liveliness to the Sound (Dynamics)
You can add liveliness to the sound to give it superb clarity and distinctness.
You can use the Memory
Backup function to store this
setting in internal memory (p.
36).
C6 D6 E6 F6
A0
1.
C8
Hold down the [TONE] button and press one of the keys from “C6” to
“F6” to select the type of dynamics.
This is set to “Off” when the
HP201 is shipped from the
Key Pressed
Setting
Explanation
C6
Off
D6
1
Creates a sound with boosted bass and treble.
E6
2
Produces a sound with chords in the low registers
that are clear and distinct.
F6
3
Creates a sound with boosted bass.
factory.
Dynamics sound control is turned off.
NOTE
For some sounds, this may
cause distortion.
19
HP201_e.book 20 ページ 2007年1月15日 月曜日 午後5時37分
Performance
Playing Sounds When the Keys Are Released
(Key Off Resonance)
You can play the “key off” sound (the subtle sound produced when the keys are
released) obtained when playing an acoustic piano.
You can use the Memory
Backup function to store this
setting in internal memory (p.
36).
C4 D4 E4 F4 G4 A4 B4 C5
A0
1.
20
Hold down the [REVERB/KEY TOUCH] button and press one of the
keys from “C4” to “C5” to adjust the volume of the key-off sound.
Key Pressed
Setting
C4
Off
D4
1
E4
2
F4
3
G4
4
A4
5
B4
6
C5
7
Explanation
There will be no key-off sound.
This is set to “4” when the
HP201 is shipped from the
Higher values will produce a louder key-off sound.
factory.
HP201_e.book 21 ページ 2007年1月15日 月曜日 午後5時37分
Performance
Adding Reverberation to the Sound (Reverb)
By applying the reverb effect you can produce a pleasant reverberation, making it
sound as though you were performing in a concert hall.
fig.panel2-5
You can use the Memory
Backup function to store this
setting in internal memory (p.
36).
1.
Press the [REVERB/KEY TOUCH] button.
The button’s indicator will light, and a reverb effect will be applied to the sound.
To cancel the reverb effect, press the [REVERB/KEY TOUCH] button, getting its
indicator to go dark.
■ Changing the Depth of the Reverb Effect
The amount (depth) of the reverb effect can be set to any of ten levels.
1.
Hold down the [REVERB/KEY TOUCH] button and press the “C ” or
“E ” key.
You can change the Depth of
the Reverb Effect by pressing
any “C ” or “E ” key.
Pressing the “C ” key as you hold down the [REVERB/KEY TOUCH] button reduces
the amount of reverb effect applied. Holding down the [REVERB/KEY TOUCH] button
and pressing the “E ” key increases the reverb effect.
This is set to “4” when the
HP201 is shipped from the
factory.
While holding down
the [Reverb/Key Touch]
button...
2.
Press
To restore the reverb depth to its factory-set state, hold down the
[REVERB/KEY TOUCH] button and press the “C ” and “E ” keys
simultaneously.
21
HP201_e.book 22 ページ 2007年1月15日 月曜日 午後5時37分
Performance
Adjusting the Keyboard Touch (Key Touch)
You can adjust the touch (playing feel) of the keyboard.
fig.panel2-7
You can use the Memory
Backup function to store this
setting in internal memory (p.
36).
A0 B0 C1 D1
1.
Hold down the [REVERB/KEY TOUCH] button and press either the
“A0,” “B0,” “C1,” or “D1” key.
The feel of the keyboard will change.
Key Pressed
22
Setting
Explanation
A0
Light
Fortissimo (ff) can be produced by playing less
strongly than usual, making the keyboard feel
lighter. This setting makes it easy to play, even for
children.
B0
Medium
This allows you to play using the most natural touch.
This is the closest to the touch of an acoustic piano.
C1
Heavy
Fortissimo (ff) cannot be produced unless you play
more strongly than usual, making the keyboard feel
heavier. Dynamic fingering adds even more feeling
to what you play.
D1
Fixed
Sounds at a fixed volume, regardless of your
keyboard playing strength.
This is set to “Medium” when
the HP201 is shipped from the
factory.
HP201_e.book 23 ページ 2007年1月15日 月曜日 午後5時37分
Performance
Transposing the Key of the Keyboard
(Transpose)
By using the “Transpose function,” you can transpose your performance without
changing the notes you play. For example, even if the song is in a difficult key with
numerous sharps ( ) or flats (
), you can transpose it to a key that is easier for you
to play.
When accompanying a vocalist, you can easily transpose the pitch to a range that is
comfortable for the singer, while still playing the notes as written (i.e., with the same
fingering positions).
fig.panel2-6
1
3
-6 -4 -2
0 2 4 5 -5 -3 -1
A0
C5
While holding down
two buttons...
1.
B5
Press
Hold down the [METRONOME] and [REVERB/KEY TOUCH] buttons,
and press the key for the note you want to set as the tonic.
Keys for Setting the Transposition:
C5–B5
The keyboard will be transposed.
This is set to “0” when the
instrument is turned on.
The available range is -6–0–5 (semitone steps).
For example, if you want the E pitch to sound when you play the C key, hold down the
[METRONOME] and [REVERB/KEY TOUCH] buttons and press the E5 key.
fig.trans.e
If you play C E G
It will sound E G# B
This setting returns to the
To cancel the transposition, hold down the [METRONOME] and [REVERB/KEY
original value (0) when you turn
TOUCH] buttons and press the “C5” key (transposition 0).
off the power.
23
HP201_e.book 24 ページ 2007年1月15日 月曜日 午後5時37分
Performance
Splitting the Keyboard Into Two Sections for
Four-Hand Performances (Twin Piano)
You can divide the keyboard into two separate sections, allowing two people to
perform in the same registers.
C1
C3
1.
C4
C2
C3
C5
C4
C6
C5
C6
C3
C7
C4
C8
C5
C6
While holding down the [TONE] button and press the “C8” key.
Off
On
NOTE
The damper resonance function
B7 C8
is not operational in Twin Piano
Mode.
C7
Press
The keyboard is divided into two separate sections, and the pitch changes.
2.
24
NOTE
The right pedal now functions as the damper pedal for the right keyboard section, and
You can’t use the Dual Play
the left pedal functions as the damper pedal for the left keyboard section.
function (p. 17) while using
Twin Piano function.
To exit the function, hold down the [TONE] button and press the “B7”
key.
HP201_e.book 25 ページ 2007年1月15日 月曜日 午後5時37分
Performance
■ Changing the Way in Which the Sound is Heard
(Twin Piano Mode)
You can choose one of two ways in which the sound will be produced.
You can use the Memory
Backup function to store this
setting in internal memory (p.
36).
A7
This is set to “1” when the
C7
HP201 is shipped from the
Press
1.
While holding down the [TONE] button, press the A7 or B 7 key to
specify how the sound is to be produced.
factory.
NOTE
If you set Twin Piano mode to
“2,” reverb will no longer be
Key Pressed
A7
B
7
Setting
Explanation
1
Notes played in the keyboard’s right zone will be
heard more loudly from the right speaker than from
the left speaker. Conversely, notes played in the
keyboard’s left zone will be heard more loudly from
the left speaker than from the right speaker.
2
Notes played in the keyboard’s right zone will be
heard only from the right speaker. Notes played in
the keyboard’s left zone will be heard only from the
left speaker.
applied when you turn on Twin
Piano mode.
NOTE
For some sounds, the sound
may not be split even if you set
Twin Piano mode to “2.”
When you change the Twin
Piano mode setting, Twin Piano
will automatically be turned on.
25
HP201_e.book 26 ページ 2007年1月15日 月曜日 午後5時37分
Performance
Using Metronome
■ Sounding the Metronome
The HP201 features a built-in metronome.
fig.panel2-4
Starting the metronome
1.
Press the [METRONOME] button, getting its indicator to light.
The metronome will sound.
The button flashes in red and green in time with the beat selected at that time. The
The beat is set to “weak beats
button lights in red on the downbeats, and in green on weak beats.
only” when the power is turned
on. When the beat is set to
Stopping the metronome
2.
“weak beats only,” the
Once again press the [METRONOME] button, getting the button to go
dark.
The metronome will stop.
■ Changing the Beat of Metronome
A0 B0 C1 D1 E1
1.
26
Hold down the [METRONOME] button and press either the “A0,”
“B0,” “C1,” “D1,” or “E1” key.
Key Pressed
A0
B0
C1
D1
E1
Beat
Weak beats
only (0/4)
2/4
3/4
4/4
6/4
[METRONOME] button only
flashes in green.
HP201_e.book 27 ページ 2007年1月15日 月曜日 午後5時37分
Performance
■ Changing the Metronome Volume
The volume of the metronome can be adjusted, with eight volume levels available.
This is set to “4” when the
instrument is turned on.
C7 D7 E7 F7 G7 A7 B7 C8
1.
Hold down the [METRONOME] button and press a white key in the
“C7” to “C8” range.
Key Pressed
C7
D7
E7
F7
G7
A7
B7
C8
Volume
0
1
2
3
4
5
6
7
When the metronome volume is
set to “0,” the metronome
sound does not play.
■ Changing the Metronome Tempo
Changing the Tempo in Single Beat Increments
1.
Hold down the [METRONOME] button and press the “C ” or “E ”
key.
You can change the tempo by
pressing any “C ” or “E ”
key.
The metronome tempo changes.
Hold down the [METRONOME] button and press the “C ” key to slow down the
tempo; continue pressing for consecutive decreases.
Hold down the [METRONOME] button and press the “E ” key to increase the tempo;
continue pressing for consecutive increases.
If you hold down the [METRONOME] button and simultaneously press the “C ” key
and “E ” key, the tempo will return to the standard tempo (
tempo of the selected song.
= 108) or the original
The range available when
adjusting the tempo of the
metronome is:
Slows down
the tempo
= 10--500.
Speeds up
the tempo
Some of the built-in songs have
a tempo and time signature that
are based on eighth notes or
half notes, such as 3/8 or 2/2.
Immediately after you’ve
played back one of these
While holding down the
[METRONOME] button...
Press
songs, the tempo will be based
on eighth notes or half notes.
27
HP201_e.book 28 ページ 2007年1月15日 月曜日 午後5時37分
Performance
Selecting the Preset Tempo
C2 D2 E2 F2 G2 A2 B2 C3
A0
1.
Hold down the [METRONOME] button and press the white keys in the
“C2” to “C3” range.
The metronome tempo changes.
Key Pressed
C2
D2
E2
F2
G2
A2
B2
C3
Tempo
60
72
84
96
108
120
138
160
Setting the Tempo Value
C4 D4 E4 F4 G4 A4 B4 C5 D5 E5 F5
A0
Enter
1.
Hold down the [METRONOME] button and press the white keys in the
“C4” to “E5” range.
The tempo can be adjusted in a range of
2.
=10–500.
Key Pressed
C4
D4
E4
F4
G4
A4
B4
C5
D5
E5
F5
Tempo
1
2
3
4
5
6
7
8
9
0
Enter
Press the “F5” key to set that tempo.
Example: Setting the Tempo to
= 120
While holding down the [METRONOME] button, press the “C4 (1)” key, the “D4 (2)”
key, and the “E5 (0)” key, in that sequence, then press the “F5” key to set the tempo.
Example: Setting the Tempo to
= 86
While holding down the [METRONOME] button, press the “C5 (8)” key and the “A4
(6)” key in that sequence, then press the “F5” key to set the tempo.
28
HP201_e.book 29 ページ 2007年1月15日 月曜日 午後5時37分
Performance
Setting the Tempo According to the Interval a Key is Pressed as you
Hold Down the [METRONOME] Button (Tap Tempo)
You can set the tempo according to the interval a key is pressed as you hold down the
[METRONOME] button. This function is called “Tap Tempo.” This feature allows you
to set the tempo you have in mind quickly and easily, without indicating the tempo
numerically.
Tap Tempo
1.
Hold down the [METRONOME] button and press the “B 0” key at
least twice.
The tempo is set to the interval between presses of the key.
29
HP201_e.book 30 ページ 2007年1月15日 月曜日 午後5時37分
Recording Your Performance
You can record your own performance.
NOTE
Listening to the playback of your recorded performance can be a helpful way for you
to evaluate your own playing.
The HP201 always saves the
newly recorded song and
erases the previously recorded
song. If you want to keep a
You can also sound a count before recording starts.
song you’ve recorded, you
This is called “count-in recording,” and allows you to match the timing of the count
should send the recorded song
so that your performance will begin smoothly.
data to a MIDI device or
computer (p. 39).
Recording
NOTE
You can’t select tones or make
detailed settings, such as those
for key touch or master tuning,
while you’re recording or while
If using count-in
recording
you’re in recording-standby
mode.
Play the keyboard
Set the tempo and time signature of the metronome before you record (p. 26, p. 27).
1.
While recording or in
recording-standby mode, you
Hold down the [SONG] button and press the [METRONOME] button.
The [SONG] button’s indicator will light, and the [METRONOME] button’s indicator
will blink orange. This is called “recording-standby mode.”
can press the [REVERB/KEY
TOUCH] button to turn reverb
on/off (p. 21).
If you want to use count-in recording
2.
Press the [METRONOME] button.
The [METRONOME] button’s indicator will change from blinking to lit.
A two-measure count will sound. The [SONG] button will blink while the count-in is
sounding. After the count-in, recording begins.
When recording begins, the [SONG] button’s indicator will change from blinking to lit.
If a recorded song has been
saved, the [TONE] button’s
indicator will blink while you
If not using count-in recording
2.
press the [SONG] button.
Play the keyboard to start recording.
When recording begins, the [METRONOME] button’s indicator will change from
blinking to lit.
NOTE
After you’ve finished recording,
3.
When you’ve finished recording, press the [SONG] button or the
[METRONOME] button.
When you press the button, the indicators for all buttons will blink, and the recorded
performance (song) will be saved in internal memory.
30
don’t turn off the power until all
indicators have stopped
blinking.
HP201_e.book 31 ページ 2007年1月15日 月曜日 午後5時37分
Recording Your Performance
Playing Back the Recorded Performance
Playing back the song immediately after you’ve stopped recording
1.
Press the [SONG] button.
The song you recorded will play back.
If you record your performance
with a time signature of 0/4,
the metronome will sound at 4/
Playing back the recorded song after you’ve played other internal
songs
1.
4 during playback.
Hold down the [SONG] button and press the “A0” key.
The recorded performance will play back.
Some of the built-in songs have
a tempo and time signature that
are based on eighth notes or
half notes, such as 3/8 or 2/2.
If you record your own
performance immediately after
A0
playing back one of these
songs, the tempo of the music
that’s recorded will be based
on eighth notes or half notes.
Erasing Recorded Performances
1.
Hold down the [SONG] button and press the [TONE] button.
The recorded performance is erased.
If a recorded song has been
saved, the [TONE] button’s
indicator will blink while you
press the [SONG] button.
31
HP201_e.book 32 ページ 2007年1月15日 月曜日 午後5時37分
Changing Various Settings
Tuning to Other Instruments’
Pitches (Master Tuning)
■ Setting the Standard Pitch to
440.0 Hz
In situations such as when playing ensemble with other
instruments, you can tune the HP201’s standard pitch to the
pitch of another instrument. The standard pitch generally refers
to the pitch of the note that’s played when you finger the
middle A key. This tuning of all the instruments to a standard
pitch is called “tuning.”
1. While holding down the [METRONOME] and
The standard pitch will be set to 440.0 Hz. This is the
most commonly used setting. The A4 (Middle A) key will
sound at 440.0 Hz.
[REVERB/KEY TOUCH] buttons, press the “C1” key
on the keyboard.
You can set the standard pitch anywhere in a range of 415.3
Hz to 466.2 Hz.
This is set to “440.0 Hz” when the HP201 is shipped from the
factory.
C1
You can use the Memory Backup function to store this
setting in internal memory (p. 36).
■ Lowering/Raising the Standard
Pitch
1. While holding down the [METRONOME] and
[REVERB/KEY TOUCH] buttons, press the “C 1”
note to lower the standard pitch, or the “E 1” note
to raise it.
Lower
the pitch
Raise
the pitch
■ Setting the Standard Pitch to
442.0 Hz
The standard pitch will be set to 442.0 Hz. This setting is
often used for concert pianos. The A4 (Middle A) key will
sound at 442.0 Hz.
1. While holding down the [METRONOME] and
[REVERB/KEY TOUCH] buttons, press the “D1” key
on the keyboard.
D1
While holding down
two buttons...
Press
Each time you press the “C 1” key, the pitch will fall by
0.1 Hz. If you continue holding the key, the pitch will
continue falling.
You can confirm the pitch of A4 by holding down the
[METRONOME] and [REVERB/KEY TOUCH] buttons and
pressing either the A0, B 0, or B0 key.
Each time you press the “E 1” key, the pitch will rise by
0.1 Hz. If you continue holding the key, the pitch will
continue rising.
A0 B0
32
HP201_e.book 33 ページ 2007年1月15日 月曜日 午後5時37分
Changing Various Settings
Changing the Temperament
You can play classical styles such as Baroque using historic
temperaments (tuning methods).
Today, compositions are generally created with equal
temperament in mind and are played using equal
temperament. However in past ages of classical music, a
variety of temperaments were used. Playing a composition
with its original tuning lets you enjoy the sonorities of the
chords that the composer originally intended.
Key
Pressed
B 3
B3
Temperament/Qualities
Pythagorean
This tuning, devised by the philosopher
Pythagoras, eliminates dissonance in fourths
and fifths. Dissonance is produced by thirdinterval chords, but melodies are euphonious.
Werckmeister
This temperament combines the Mean Tone and
Pythagorean tunings. Performances are
possible in all keys (first method, number three).
This is set to “Equal” when the instrument is turned on.
1. While holding down the [METRONOME] and
[REVERB/KEY TOUCH] buttons, press the
appropriate key (F3–B3) on the keyboard.
■ Setting the Tonic
When playing with tuning other than equal temperament, you
need to specify the tonic note for tuning the song to be
performed (that is, the note that corresponds to C for a major
key or to A for a minor key).
If you choose an equal temperament, there’s no need to select
a tonic note.
1. While holding down the [METRONOME] and
F3 G3 A3 B3
A0
[REVERB/KEY TOUCH] buttons, press the tonic (root)
of the key (C4–B4).
C3
You can choose from among the seven temperaments
described below.
Key
Pressed
F3
F 3
Temperament/Qualities
C4 D4 E4 F4 G4 A4 B4
Equal
In this tuning, each octave is divided into twelve
equal steps. Every interval produces about the
same amount of slight dissonance.
Just Major
This tuning eliminates ambiguities in the fifths
and thirds. It is unsuited to playing melodies
and cannot be transposed, but is capable of
beautiful sonorities.
G3
Just Minor
The Just tunings differ from major and minor
keys. You can get the same effect with the minor
scale as with the major scale.
A 3
Kirnberger
This is an improvement of the Mean Tone and
Just tunings that provides a high degree of
freedom of modulation. Performances are
possible in all keys (third method).
A3
Mean Tone
This scale makes some compromises in just
intonation, enabling transposition to other keys.
A0
NOTE
When performing in ensemble with other instruments, be
aware that depending on the key, there may be some
shifting of the pitch. Tune the HP201 to the standard pitch
of the other instruments.
33
HP201_e.book 34 ページ 2007年1月15日 月曜日 午後5時37分
Changing Various Settings
Changing the Damper Pedal’s
Resonance (Damper Resonance)
Setting the Tuning Curve
(Stretch Tuning)
On an acoustic piano, depressing the damper pedal makes
the notes you play resonate with other strings, adding rich
reverberations and fatness to the sound. The damper pedal on
the HP201 recreates this resonance (damper resonance) when
depressed.
You can select from eight levels of depth for the resonant
sound (resonance level).
A piano is generally tuned to a pitch with a lower bass range
and a higher treble range than equal temperament. This
special tuning method for pianos is called “Stretch Tuning.”
NOTE
This effect works only with the piano tones.
Stretch Tuning is set to On when the instrument is turned
on.
You can use the Memory Backup function to store this
setting in internal memory (p. 36).
1. While holding down the [METRONOME] and
[REVERB/KEY TOUCH] buttons, the “D2” note to turn
the setting On, or press the “C2” note to turn the
setting Off.
This is set to “4” when the HP201 is shipped from the
factory.
NOTE
This setting is enabled only with the piano tones. You
cannot set this for other tones.
1. While holding down the [REVERB/KEY TOUCH]
buttons and press the appropriate key (C2–C3) on
the keyboard.
C2 D2
A0
Press
Key
Pressed
Setting
Explanation
Off
This is the standard tuning curve.
This is the right choice when using
Dual play (p. 17), or when playing
in ensemble with other instruments.
On
This tuning curve expands the bass
and treble ends somewhat.
It is suitable for performances such
as piano solos.
C2 D2 E2 F2 G2 A2 B2 C3
C2
A0
Key
Pressed
C2
D2
E2
F2
G2
A2
B2
C3
Depth of
Effect
Off
1
2
3
4
5
6
7
Larger values will produce a deeper effect.
34
D2
HP201_e.book 35 ページ 2007年1月15日 月曜日 午後5時37分
Changing Various Settings
Disabling Everything Except Piano
Play (Panel Lock)
The “Panel Lock” function locks the HP201 in a state where
only piano performance can be used, and all buttons will be
disabled. This prevents the settings from being inadvertently
modified even if children press the buttons accidentally.
NOTE
In the Panel Lock state, only the grand piano sound can
be played.
1. Turn the volume to the minimum, and press the
[POWER] switch to turn off the power.
2. Hold down the [TONE] button and press the
[POWER] switch to turn on the power.
Continue holding down the [TONE] button until the panel
indicator lights.
Using the V-LINK function
Connecting the HP201 to a V-LINK compatible image device
allows you to control the images with the HP201.
V-LINK
V-LINK (
) is a function that allows music and
images to be performed together. By using MIDI to connect
two or more V-LINK compatible devices, you can easily enjoy
a wide range of visual effects that are linked to the expressive
elements of a music performance.
How to Use the V-LINK
V-LINK is set to Off when the instrument is turned on.
1. While holding down the [METRONOME] and
[REVERB/KEY TOUCH] buttons, the “A 7” note to
turn the setting On, or press the “G7” note to turn
the setting Off.
While holding down the [TONE] button,
press the [POWER] switch.
G7
C8
Press
C1 D1 E1 F1 G1 A1 B1
Key
Pressed
G7
All buttons are disabled.
Adjust the volume by using the [VOLUME] knob.
A 7
When you play the keyboard, the grand piano sound will
be heard.
To defeat the Panel Lock function, turn the volume down to
the minimum, and turn on the power once again.
Setting
Explanation
Off
The V-LINK function is switched off.
On
The V-LINK function is switched on.
You can control images using the
twelve keys at the left end of the
keyboard.
NOTE
While V-LINK is switched on, no sound is produced when
you press any of the twelve keys at the left end of the
keyboard.
All button indicators light up when the V-LINK function is
on.
35
HP201_e.book 36 ページ 2007年1月15日 月曜日 午後5時37分
Changing Various Settings
Remembering the Settings Even
when the Power is Turned Off
(Memory Backup)
Normally, the settings of the various variations will revert to
their default values when the power is turned off. However,
you can specify that the various settings will be remembered
even when the power is turned off.
This function is called “Memory Backup.”
Restoring the Original Default
Settings (Factory Reset)
The memory backup settings can be restored to the original
default condition. This operation is referred to as “Factory
Reset.”
1. While holding down the [SONG] button and
[METRONOME] button, hold down the C8 key for
approximately five seconds.
Stored Settings
• Brilliance (p. 19)
• Dynamics (p. 19)
• Reverb On/Off, Depth of the Reverb (p. 21)
• Damper Resonance (p. 34)
C8
• Key Off Resonance (p. 20)
• Key Touch (p. 22)
• Twin Piano Mode (p. 25)
Hold down for five seconds
• Master Tuning (p. 32)
• USB Driver (p. 40) *Stored when you make the setting
2. When the indicators of all buttons start blinking,
1. While holding down the [SONG] button and
[METRONOME] button, hold down the A0 key for
approximately five seconds.
A0
Hold down for five seconds
The indicators of all buttons will blink several times. When
memory backup has been completed, the HP201 will
return to its previous state.
36
switch off the power, then turn it back on again.
HP201_e.book 37 ページ 2007年1月15日 月曜日 午後5時37分
Connecting External Devices
Connecting to Audio Equipment
You can connect audio devices to play the sound of the
HP201 through the speakers of your audio system, or to
record your performance on a tape recorder or other
recording device. When connecting, please use an audio
cable with a standard phone plug (sold separately).
Playing the sound of an audio device through the
speakers of the HP201
fig.audio2.e
Output R/L
(Line Out, Aux Out)
HP201
Connection Examples
NOTE
To prevent malfunction and/or damage to speakers or
other devices, always turn down the volume, and turn off
the power on all devices before making any connections.
NOTE
❍ Use the following procedure when turning on the power.
1. Turn on the power of the connected device.
2. Turn on the power of the HP201.
Some connection cables contain resistors. Do not use
cables that incorporate resistors for connecting to this unit.
The use of such cables can cause the sound level to be
extremely low, or impossible to hear. For information on
cable specifications, contact the manufacturer of the
cable.
Playing the sound of the HP201 through the speakers of
an audio system/Recording the performance of the
HP201 on a recording device
fig.audio1.e
Input R/L
(Line In, Aux In)
3. Adjust the volume of each device.
NOTE
You cannot use the HP201 to adjust the volume of the
connected sound generating device.
Turning off the power
1. Set the volume of the HP201 and of the connected
devices to the minimum position.
2. Turn off the power to the HP201.
3. Turn off the connected equipment.
HP201
❍ Use the following procedure when turning on the power.
1. Turn on the power of the HP201.
2. Turn on the power of the connected device.
3. Adjust the volume of each device.
When Recording HP201 Performances on a Recording
Device
4. Start recording with the connected device.
5. Perform on the HP201.
6. When the performance ends, stop recording on the
connected equipment.
37
HP201_e.book 38 ページ 2007年1月15日 月曜日 午後5時37分
Connecting External Devices
Connecting MIDI Devices
Perform on the HP201 to play a MIDI sound module
fig.midi1.e
By connecting an external MIDI device and exchanging
performance data, you can control the performances on one
device from the other. For instance, you can output sound from
the other instrument or switch tones on the other instrument.
■ What’s MIDI?
MIDI stands for Musical Instrument Digital Interface, an
international standard which allows performance information
to be communicated among electronic musical instruments and
computers.
The HP201 provides MIDI connectors, which allow
performance data to be exchanged with external devices.
When these connectors are used to connect the HP201 to
external devices, an even wider range of possibilities becomes
available.
MIDI Cable
MIDI Out/In
Connectors
THRU
MIDI
OUT
IN
MIDI Sound Module
■ MIDI Send Channel Settings
Connection Examples
NOTE
To prevent malfunction and/or damage to speakers or
other devices, always turn down the volume, and turn off
the power on all devices before making any connections.
Playing the HP201 from a MIDI sequencer/Recording an
HP201 performance on a MIDI sequencer
MIDI features sixteen MIDI channels, numbered 1–16. Simply
connecting a cable is not enough for communication to take
place. The connected devices must be set to use the same MIDI
channels. Otherwise, no sound will be produced, and no
sounds can be selected.
* The HP201 receives all channels 1–16.
fig.midi2.e
When you’re using Dual Play (p. 17) on the HP201, the
notes for “Tone 2” are transmitted on channel 5. This MIDI
transmit channel setting is fixed. If you’re using Dual Play
with an external MIDI device connected, set your device
to a channel other than channel 5.
When the HP201 is turned on, Channel “1” is selected.
1. While holding down the [METRONOME] and
MIDI Cable
[REVERB/KEY TOUCH] buttons, press the
appropriate key (C6–E 7) on the keyboard.
The MIDI transmit channel will switch to the number that
corresponds to the note you pressed.
MIDI Out/In
Connector
OUT MIDI IN
MIDI Sequencer
Set Local Off if you have connected the HP201 to a MIDI
sequencer. Refer to “Switching Local Control On and Off”
(p. 39). Also set your MIDI sequencer to MIDI Thru mode
(so that messages received at MIDI IN will be retransmitted without change from MIDI OUT). For details,
refer to the owner’s manual of your MIDI sequencer.
2
7
9 11
14 16
1 3 5 6 8 10 12 13 15
C6
38
4
C8
HP201_e.book 39 ページ 2007年1月15日 月曜日 午後5時37分
Connecting External Devices
■ Switching Local Control On and
Off
When connecting a MIDI sequencer, set Local Control to
“OFF.”
1. While holding down the [METRONOME] and
[REVERB/KEY TOUCH] buttons, the “C8” note to turn
the setting On, or press the “B7” note to turn the
setting Off.
As illustrated, information describing what has been played on
the keyboard is passed to the internal sound generator over
two different routes, (1) and (2). As a result, you hear
overlapping or intermittent sounds. To prevent this from
happening, route (1) must be severed, by setting the unit to
what is known as “Local Off.”
fig.localcont.e
B7 C8
(1) Local On
Sequencer
MIDI
IN
Sound
Generator
MIDI
OUT
Memory
MIDI
OUT
MIDI
IN
(2) Thru function On
Each note played
is sounded twice
Local Control ON
The keyboard and the internal sound generator are in a linked
state.
fig.localon.e
Sound is emitted
Key Pressed
Value
B7
Off
C8
On
■ Sending Recorded Performance
Data to a MIDI Device
(Composer Out)
When Composer Out is active, you can send performance
data recorded with the HP201 to a connected MIDI device or
computer.
Sound Generator
Local On
When you turn on the power, this is set to “Off.”
1. While holding down the [METRONOME] button and
Local Control OFF
The keyboard and the internal sound generator are in an
unlinked state. No sound will be produced by the keyboard
when it is played.
[REVERB/KEY TOUCH] button, press the F7 or F 7
key to switch Composer Out on/off.
fig.localoff.e
No sound produced
Sound Generator
Local Off
F7
C8
When a Roland MT series instrument is connected, it is not
necessary to make the Local Off setting. MT units transmit
Local Off messages when their power is switched on. If
you turn on the power in the order of the HP201 → MT
series, Local Off will be set automatically.
Local On is set when the power is switched on.
Key Pressed
Value
F7
Off
F 7
On
If Composer Out is turned on, the song data will be sent
to a connected MIDI device or computer when you play
back a recorded song.
39
HP201_e.book 40 ページ 2007年1月15日 月曜日 午後5時37分
Connecting External Devices
Connecting to a Computer
If you use a USB cable (commercially available) to connect the
USB (MIDI) connector located on the HP201’s bottom panel to
the USB connector of your computer, you’ll be able to do the
following things.
Caution
• To avoid the risk of malfunction and/or speaker damage,
always make sure to turn the volume all the way down
and turn off the power on all equipment before you make
any connections.
• Only MIDI data can be transmitted and received via USB.
• Use the HP201 to play SMF music files played back by
MIDI-compatible software.
• A USB cable is not included. If you need to obtain one,
ask the dealer where you purchased the HP201.
• By transferring MIDI data between the HP201 and your
sequencer software, you’ll be able to enjoy a wide range
of possibilities for music production and editing.
• Switch on power to the HP201 before you start up the
MIDI application on your computer. Don’t turn the
HP201’s power on/off while your MIDI application is
running.
Connect the HP201 to your computer as shown below.
fig.comp.e
■ Changing the USB Driver Settings
1. While holding down the [METRONOME] button and
[REVERB/KEY TOUCH] button, press the A7 or B 7
key to choose the USB driver.
USB(MIDI)
Connecor
Computer
USB
Cable
USB
Connector
A7
C8
Refer to the Roland website for system requirements.
Roland website: http://www.roland.com/
If connection to your computer is
unsuccessful...
Normally, you don’t need to install a driver in order to connect
the HP201 to your computer. However, if some problem
occurs, or if the performance is poor, using the Roland
original driver may solve the problem.
Key
Pressed
A7
B 7
Setting
Explanation
Original
Choose this if you want to use a
USB driver downloaded from the
Roland website.
Generic
Choose this if you want to use
the standard USB driver that was
included with your computer.
Normally, you should use this
mode.
For details on downloading and installing the Roland original
driver, refer to the Roland website.
Roland website:http://www.roland.com/
Specify the USB driver you want to use, and then install the
driver. For details, refer to “Changing the USB Driver Settings”
(next item).
40
2. Turn the power off, then on again.
HP201_e.book 41 ページ 2007年1月15日 月曜日 午後5時37分
Appendices
Troubleshooting
If you think there’s a problem, read this first.
Case
The power doesn’t
come on
The button doesn’t
work
Cause/Remedy
Is the power cord connected and plugged in
correctly? (p. 12)
Is the panel locked? (p. 35)
Turn the power off, then back on.
Is the volume level of the HP201 turned all the
way down? (p. 14)
No sound is heard
In the upper range,
the sound changes
abruptly beyond a
certain key
Are headphones plugged in? (p. 13)
Has a plug remained connected to the Phones
jack?
Plugging headphones or other plugs into the
headphone jack stops sounds from playing
through the speakers.
Is Local Off selected?
When Local Control is set to Off, no sound is
produced by playing the keyboard. Set Local
Control to “On” (p. 39).
Is V-LINK switched on?
While V-LINK is switched on, no sound is
produced when you press any of the twelve
keys at the left end of the keyboard (p. 35).
No sound is heard
Have all devices been switched on?
(when a MIDI
Are the MIDI cables connected correctly?
instrument is
Does the MIDI channel match the connected
instrument? (p. 38)
connected)
Case
A High-pitched
whine is produced
Is the HP201 in Dual play? (p. 17)
Sounds are heard
twice (doubled)
when the keyboard
is played
Tone doesn’t change
Not all played notes
are sounded
When the HP201 is connected to an external
sequencer, set it to the Local OFF mode
(p. 39).
Alternatively, the sequencer could be set so its
MIDI Thru feature is OFF.
Is the panel locked? (p. 35)
Turn the power off, then back on.
The bass range
The maximum number of notes that the
HP201 can play simultaneously is 128.
Frequent use of the damper pedal when
playing along with a song may result in
performance data with too many notes,
causing some notes to drop out.
is a vibrating
sounds odd, or there
resonance
Have you set Transpose? (p. 23)
The tuning or pitch of
the keyboard or
song is off
Depressing a pedal
has no effect, or the
pedal effect doesn’t
stop
The pedal rattles
Are the settings for the “Temperament” (p. 33)
and “Stretch Tuning” (p. 34) correct?
Is the setting for the “Master Tuning” correct?
(p. 32)
Is the pedal connected correctly?
Make sure the pedal cord is securely
connected to the pedal jack on the bottom of
the unit, at the rear (p. 12).
The volume level of
the instrument
connected to Input
jacks is too low
Cause/Remedy
On an acoustic piano, notes in the upper one
and a half octaves of the keyboard continue
to sound until they decay naturally, regardless
of the damper pedal. There is a difference in
the timbre as well. Roland pianos faithfully
simulate such characteristics of the acoustic
piano. On the HP201, the range that is
unaffected by the damper pedal will change
depending on the Transpose setting.
When listening through headphones:
Some of the more flamboyant and
effervescent piano tones feature an ample
high-end component, which may make
the sound appear to have metallic
reverberation added. Since this
reverberation becomes particularly
audible when supplemented by heavy
reverb, you may be able to diminish the
problem by reducing the amount of
reverb applied to the sound.
When listening through speakers:
Here, a different cause (such as
resonance produced by the HP201)
would be suspect. Consult your Roland
dealer or nearest Roland Service Center.
When listening through speakers:
Playing at loud volumes may cause
instruments near the HP201 to resonate.
Resonation can also occur with
fluorescent light tubes, glass doors, and
other objects. In particular, this problem
occurs more easily when the bass
component is increased, and when the
sound is played at higher volumes. Use
the following measures to suppress such
resonance.
• Place speakers so they are 10–15 cm
from walls and other surfaces.
• Reduce the volume.
• Move the speakers away from any
resonating objects.
When listening through headphones:
Here, a different cause would be suspect.
Consult your Roland dealer or nearest
Roland Service Center.
Could you be using a connection cable that
contains a resistor?
Use a connection cable that does not contain
a resistor.
Adjust the adjuster underneath the pedal so
that the adjuster presses firmly against the
floor surface (p. 14).
41
HP201_e.book 42 ページ 2007年1月15日 月曜日 午後5時37分
Tone List
[TONE] button’s Tone: While holding down the [TONE] button, press the corresponding key.
A0 B0 C1 D1 E1 F1 G1 A1 B1 C2 D2 E2
C1
C2
C3
C4
C5
[TONE] button’s tone
(p. 16, 17)
Tone
Grand Piano1
Key
Pressed
A0
B 0
Grand Piano2
B0
Honky-tonk
C1
C 1
Harpsichord
Pop E.Piano
E1
FM E.Piano
F1
F 1
ChurchOrgan2
B1
Nason flute 8'
C2
C 2
42
Soft Pad
Morning Lite
Harp
Piano + Strings
D2
E 2
Ballad Organ
Aerial Choir
A1
B 1
Combo Jazz Organ
Orchestra Strings
G1
A 1
ChurchOrgan1
Rich Strings
D1
E 1
Vibraphone
Tone
E2
Piano + Choir
C6
C7
HP201_e.book 43 ページ 2007年1月15日 月曜日 午後5時37分
Internal Song List
Song No.
Key
35
A 3
Präludium
36
A3
Jägerlied
37
B 3
38
B3
Für Elise
39
C4
Türkischer Marsch (Mozart)
40
C 4
Ständchen
41
D4
Humoreske
42
E 4
Blumenlied
43
E4
Alpenglöckchen
44
F4
Menuett G dur (Beethoven)
45
F 4
Venezianisches Gondellied
46
G4
Alpenabendröte
47
A 4
48
A4
Auf Flügeln des Gesanges
49
B 4
C2
Mazurka No.5
50
B4
Wiener Marsch
16
C 2
Gymnopédie 1
51
C5
Le Coucou
17
D2
Étude, op.25-1
52
C 5
18
E 2
Clair de Lune
53
D5
19
E2
Étude, op.10-5
54
E 5
20
F2
Dr. Gradus ad Parnassum
55
E5
Heidenröslein
21
F 2
Grande Valse Brillante
56
F5
Zigeuner Tanz
22
G2
La prière d'une Vierge
57
F 5
La Cinquantaine
23
A 2
Course en Troïka
58
G5
Csikos Post
24
A2
To The Spring
59
A 5
25
B 2
Valse, op.64-2
60
A5
26
B2
Radetzky Marsch
61
B 5
27
C3
Träumerei
62
B5
Sonatine op.36-1 (Clementi)
28
C 3
Moments Musicaux 3
63
C6
Sonatine op.20-1 (Kuhlau)
29
D3
Prélude, op.28-15
64
C 6
Sonatine No.5 (Beethoven)
30
E 3
Harmonious Blacksmith
65
D6
31
E3
Ungarische Tänze 5
32
F3
Türkischer Marsch (Beethoven)
33
F 3
Nocturne No.2
34
G3
Frühlingslied
Song No.
Key
1
B 0
2
B0
La Campanella
*
3
C1
Trio Grande
*
4
C 1
Scherzo No.2
5
D1
Sonate No.15
6
E 1
Liebesträume 3
7
E1
Étude, op.10-3
8
F1
Je te veux
9
F 1
Valse, op.64-1
10
G1
Golliwog’s Cakewalk
11
A 1
12
A1
13
B 1
14
B1
15
Song Name
La Fille aux Cheveux de Lin
*
Fantaisie-Impromptu
Arabesque 1
An der schönen, blauen
Donau
*
*
Song Name
*
Menuet Antique
Farewell to the Piano
Brautchor
Battle of Waterloo
Menuett G dur (Bach)
Spinnerlied
Gavotte
Dolly's Dreaming Awakening
La Violette
Fröhlicher Landmann
Fly Flee
* All rights reserved. Unauthorized use of this material for
purposes other than private, personal enjoyment is a
violation of applicable laws.
* Songs marked by “*” have an orchestral accompaniment.
43
HP201_e.book 44 ページ 2007年1月15日 月曜日 午後5時37分
Easy Operation List
■ Tone Settings
While holding down the [TONE] button, press the corresponding key.
A0 B0 C1 D1 E1 F1 G1 A1 B1 C2 D2 E2
C1
C2
C4 D4 E4 F4 G4 A4 B4
C3
C4
[TONE] button’s
tone (p. 16, 17)
C6 D6 E6 F6
C5
Brilliance
(p. 19)
C6
Dynamics
(p. 19)
A7 B7 C8
C7
Twin Piano
Mode (p. 25)
C8
Twin Piano
On/Off
(p. 24)
■ Metronome Settings
While holding down the [METRONOME] button, press the corresponding key.
Tap Tempo
(p. 29)
A0 B0 C1 D1 E1
C1
Beat (p. 26)
44
C2 D2 E2 F2 G2 A2 B2 C3
C4 D4 E4 F4 G4 A4 B4 C5 D5 E5 F5
C2
C4
C3
Metronome Tempo
(Reference Tempo) (p. 28)
C5
Metronome Tempo (Tempo Value)
(p. 28)
C7 D7 E7 F7 G7 A7 B7 C8
C6
C7
C8
Metronome Volume
(p. 27)
HP201_e.book 45 ページ 2007年1月15日 月曜日 午後5時37分
Easy Operation List
■ Key Touch/Damper Resonance/Key Off Resonance Settings
While holding down the [REVERB/KEY TOUCH] button, press the corresponding key.
A0 B0 C1 D1
C1
Key Touch
(p. 22)
C2 D2 E2 F2 G2 A2 B2 C3
C4 D4 E4 F4 G4 A4 B4 C5
C2
C4
C3
Damper Resonance
(p. 34)
C5
C6
C7
C8
Key Off Resonance
(p. 20)
■ Other Settings
While holding down the [METRONOME] and [REVERB/KEY TOUCH] button,
press the corresponding key.
A0 B0 C1 D1
C1
Master Tuning
(p. 32)
F3 G3 A3 B3 C4 D4 E4 F4 G4 A4 B4 C5 D5 E5 F5 G5 A5 B5 C6 D6 E6 F6 G6 A6 B6 C7 D7
C2 D2
C2
Streach Tuning
(p. 34)
C3
C4
Temperament/
Tonic Note (p. 33)
C5
C6
Transpose
(p. 23)
C7
F7 G7 A7 B7 C8
C8
Setting the MIDI
Channel (p. 38)
Composer Out
(p. 39)
USB
Driver
(p. 40)
Local
On/Off
(p. 39)
V-LINK (p. 35)
45
HP201_e.book 46 ページ 2007年1月15日 月曜日 午後5時37分
MIDI Implementation Chart
DIGITAL PIANO
Model HP201
Transmitted
Function...
Default
Changed
1
1–16
1–16
1–16
Mode
Default
Messages
Altered
Mode 3
x
Mode 3
Mode 3, 4 (M=1)
Note
Number :
True Voice
**************
0–127
0–127
Velocity
Note ON
Note OFF
O
O
O
O
After
Touch
Key’s
Ch’s
x
x
O
O
x
O
O
x
x
x
x
x
x
O
x
O
O
x
O
x
x
x
O
O
O
O
O
O
O
O
O
O
O
O
O (Reverb)
O (Chorus)
O
O
0 ... 98
**************
O
0–127
O
O
Pitch Bend
0, 32
1
5
6, 38
7
10
11
64
65
66
67
84
91
93
98, 99
100, 101
Prog
Change
: True #
System Exclusive
46
Remarks
*2
**************
15–113, 119–127
System
Common
: Song Pos
: Song Sel
: Tune
x
x
x
x
x
x
System
Real Time
: Clock
: Commands
O
O
x
x
Aux
Message
: All sound off
: Reset all controllers
: Local Control
: All Notes OFF
: Active Sense
: Reset
x
x
x
x
O
x
O (120, 126, 127)
O
O
O (123–125)
O
x
Notes
Version : 1.00
Recognized
Basic
Channel
Control
Change
Date : Jan. 1, 2007
MIDI Implementation Chart
*1
*1
*1
*1
*1
*1
*1
*1
*1
*1
*1
*1
*1
*1
*1
Bank select
Modulation
Portamento time
Data entry
Volume
Panpot
Expression
Hold 1
Portamento
Sostenuto
Soft
Portamento control
Effect1 depth
Effect3 depth
NRPN LSB, MSB
RPN LSB, MSB
Program number 1–128
* 1 O x is selectable by Sys Ex.
* 2 Recognized as M=1 even if M=1.
Mode 1 : OMNI ON, POLY
Mode 2 : OMNI ON, MONO
O : Yes
Mode 3 : OMNI OFF, POLY
Mode 4 : OMNI OFF, MONO
X : No
HP201_e.book 47 ページ 2007年1月15日 月曜日 午後5時37分
Main Specifications
Keyboard
Keyboard
88 keys, PHA II keyboard
Touch Sensitivity
Light, Medium, Heavy, Fixed
Keyboard Modes
Whole, Dual (volume balance adjustable), Twin piano
Sound Generator
Max. Polyphony
128 voices
Tones
20 tones
Tone available at time of MIDI data performance: 285 tones (including 8 drum sets, 1 SFX set)
Temperament
7 types, selectable tonic
Stretched Tuning
On/Off
Master Tuning
415.3–466.2 Hz (adjustable in increments of 0.1 Hz)
Transpose
-6–+5 (in semitones)
Effects
Reverb (10 levels), Key Off Resonance (only for piano tones, 7 levels, Off),
Damper Resonance (only for piano tones, 7 levels, Off), Dynamics (3 types, Off)
Recorder
Track
1 track
Number of songs stored
1 song
Number of notes stored
Approx. 10000 notes
Controls
Song Select, All Song Play/Stop, Rec
Tempo
Quarter note = 10 to 500
Resolution
120 ticks per quarter note
Metronome
Beat
0/4, 2/4, 3/4, 4/4, 6/4
Volume
8 levels
Others
Preset Songs
65 songs
Rated Power Output
25 W x 2
Speakers
12 cm x 2
Control
Volume
Pedals
Damper (half-pedal recognition), Soft (half-pedal recognition), Sostenuto
Other Functions
Panel Lock, V-LINK
Connectors
AC inlet, Pedal connector, Input jacks (L/Mono, R), Output jacks (L/Mono, R),
MIDI connectors (In, Out), Phones jack (Stereo) x 2, USB (MIDI) connector
Power Supply
AC 115 V, AC 117 V, AC 220 V, AC 230 V, AC 240 V (50/60 Hz)
Power Consumption
48 W
Dimensions
(including piano stand)
1387 (W) x 422 (D) x 1012 (H) mm (with Music Rest)
54-5/8 (W) x 16-5/8 (D) x 39-7/8 (H) inches
1387 (W) x 422 (D) x 822 (H) mm (without Music Rest)
54-5/8 (W) x 16-5/8 (D) x 32-3/8 (H) inches
Weight
(including the dedicated
stand)
54 kg / 119 lbs
Accessories
Owner’s manual, Power Cord, Headphones Hook, Music Rest, Music Rest attachment screws
* In the interest of product improvement, the specifications and/or appearance of this unit are subject to change without prior
notice.
47
HP201_e.book 48 ページ 2007年1月15日 月曜日 午後5時37分
Index
A
AC Inlet ............................................................... 11–12
Adjuster ..................................................................... 14
Audio Equipment ........................................................ 37
MIDI Connector .................................................... 11, 38
MIDI Devices .............................................................. 38
Music Rest ................................................................. 12
O
B
Output Jack ......................................................... 11, 37
Beat .......................................................................... 26
Bottom Panel .............................................................. 11
Brilliance ................................................................... 19
P
C
Composer Out ............................................................
Computer ..................................................................
Control Panel .............................................................
Count-in Recording .....................................................
39
40
11
30
D
Damper Pedal ............................................................ 14
Damper Resonance ............................................... 14, 34
Dual Balance ............................................................. 18
Dual Play ............................................................. 17–18
Dynamics ................................................................... 19
Panel Lock ................................................................. 35
Pedal ........................................................................ 14
Pedal Connector ................................................... 11–12
Pedal Cord ................................................................ 12
Phones Jack ......................................................... 11, 13
Playing Back
Internal Song ........................................................ 15
Recorded Performance ........................................... 31
Power ....................................................................... 13
Power Cord ............................................................... 12
[POWER] Switch ............................................ 11, 13, 35
R
Erasing
Recorded Performance ........................................... 31
Rear Panel ................................................................. 11
Recording .................................................................. 30
Reverb ...................................................................... 21
Depth ................................................................... 21
[REVERB/KEY TOUCH] Button ... 11, 20–23, 32–35, 38–40
F
S
E
Factory Reset .............................................................. 36
Headphone Hook ....................................................... 13
Headphones .............................................................. 13
Soft Pedal ..................................................................
[SONG] Button .................................. 11, 15, 30–31,
Sostenuto Pedal ..........................................................
Standard Pitch ............................................................
Stretch Tuning ............................................................
I
T
H
Input Jack ............................................................ 11, 37
Internal Song .............................................................. 15
K
Key Off Resonance ..................................................... 20
Key Touch .................................................................. 22
L
Lid ............................................................................
Local Control ..............................................................
Local Off ...................................................................
Local On ...................................................................
12
39
39
39
M
Master Tuning ............................................................ 32
Memory Backup ......................................................... 36
Metronome ................................................................ 26
Beat ..................................................................... 26
Tempo ............................................................ 27–29
Volume ................................................................. 27
[METRONOME] Button ....... 11, 23, 26–30, 32–36, 38–40
MIDI .......................................................................... 38
MIDI Channel ............................................................. 38
48
14
36
14
32
34
Tap Tempo ................................................................ 29
Temperament ............................................................. 33
Tempo ....................................................................... 27
Tone ......................................................................... 16
Tone 1 ...................................................................... 18
Tone 2 ...................................................................... 18
[TONE] Button ......................... 11, 16–19, 24–25, 31, 35
Tonic ......................................................................... 33
Transpose .................................................................. 23
Tuning ....................................................................... 32
Tuning Curve ............................................................. 34
Twin Piano ................................................................. 24
Twin Piano Mode ................................................. 24–25
U
USB (MIDI) Connector ........................................... 11, 40
USB Driver ................................................................. 40
V
V-LINK ....................................................................... 35
Volume ...................................................................... 14
Metronome ........................................................... 27
[VOLUME] Knob ............................................. 11, 13–14
HP201_e.book 49 ページ 2007年1月15日 月曜日 午後5時37分
Information
AFRICA
EGYPT
Al Fanny Trading Office
9, EBN Hagar A1 Askalany
Street,
ARD E1 Golf, Heliopolis,
Cairo 11341, EGYPT
TEL: 20-2-417-1828
REUNION
Maison FO - YAM Marcel
25 Rue Jules Hermann,
Chaudron - BP79 97 491
Ste Clotilde Cedex,
REUNION ISLAND
TEL: (0262) 218-429
SOUTH AFRICA
T.O.M.S. Sound & Music
(Pty)Ltd.
2 ASTRON ROAD DENVER
JOHANNESBURG ZA 2195,
SOUTH AFRICA
TEL: (011)417 3400
FAX: (011)417 3462
Paul Bothner(PTY)Ltd.
Royal Cape Park, Unit 24
Londonderry Road, Ottery 7800
Cape Town, SOUTH AFRICA
TEL: (021) 799 4900
ASIA
CHINA
Roland Shanghai Electronics
Co.,Ltd.
5F. No.1500 Pingliang Road
Shanghai 200090, CHINA
TEL: (021) 5580-0800
Roland Shanghai Electronics
Co.,Ltd.
(BEIJING OFFICE)
10F. No.18 3 Section Anhuaxili
Chaoyang District Beijing
100011 CHINA
TEL: (010) 6426-5050
HONG KONG
When you need repair service, call your nearest Roland Service Center or authorized Roland
distributor in your country as shown below.
PHILIPPINES
CURACAO
URUGUAY
NORWAY
JORDAN
G.A. Yupangco & Co. Inc.
339 Gil J. Puyat Avenue
Makati, Metro Manila 1200,
PHILIPPINES
TEL: (02) 899 9801
Zeelandia Music Center Inc.
Orionweg 30
Curacao, Netherland Antilles
TEL:(305)5926866
Todo Musica S.A.
Francisco Acuna de Figueroa
1771
C.P.: 11.800
Montevideo, URUGUAY
TEL: (02) 924-2335
Roland Scandinavia Avd.
Kontor Norge
Lilleakerveien 2 Postboks 95
Lilleaker N-0216 Oslo
NORWAY
TEL: 2273 0074
MUSIC HOUSE CO. LTD.
FREDDY FOR MUSIC
P. O. Box 922846
Amman 11192 JORDAN
TEL: (06) 5692696
VENEZUELA
POLAND
Instrumentos Musicales
Allegro,C.A.
Av.las industrias edf.Guitar
import
#7 zona Industrial de Turumo
Caracas, Venezuela
TEL: (212) 244-1122
ROLAND POLSKA SP. Z O.O.
UL. Gibraltarska 4.
PL-03 664 Warszawa
POLAND
TEL: (022) 679 4419
EASA HUSAIN AL-YOUSIFI
& SONS CO.
Abdullah Salem Street,
Safat, KUWAIT
TEL: 243-6399
SINGAPORE
SWEE LEE MUSIC
COMPANY PTE. LTD.
150 Sims Drive,
SINGAPORE 387381
TEL: 6846-3676
Instrumentos Fernando Giraldez
Calle Proyecto Central No.3
Ens.La Esperilla
Santo Domingo,
Dominican Republic
TEL:(809) 683 0305
TAIWAN
ECUADOR
ROLAND TAIWAN
ENTERPRISE CO., LTD.
Room 5, 9fl. No. 112 Chung
Shan N.Road Sec.2, Taipei,
TAIWAN, R.O.C.
TEL: (02) 2561 3339
Mas Musika
Rumichaca 822 y Zaruma
Guayaquil - Ecuador
TEL:(593-4)2302364
THAILAND
Theera Music Co. , Ltd.
330 Soi Verng NakornKasem,
New Road, Sumpantawongse,
Bangkok 10100, THAILAND
TEL: (02) 224-8821
AUSTRALIA/
NEW ZEALAND
AUSTRALIA/
NEW ZEALAND
Roland Corporation
Australia Pty.,Ltd.
CENTRAL/LATIN
AMERICA
INDIA
BRAZIL
Cosmos Corporation
1461-9, Seocho-Dong,
Seocho Ku, Seoul, KOREA
TEL: (02) 3486-8855
MALAYSIA
Roland Asia Pacific Sdn. Bhd.
45-1, Block C2, Jalan PJU 1/39,
Dataran Prima, 47301 Petaling
Jaya, Selangor, MALAYSIA
TEL: (03) 7805-3263
Casa Instrumental
Calzada Roosevelt 34-01,zona 11
Ciudad de Guatemala
Guatemala
TEL:(502) 599-2888
HONDURAS
Almacen Pajaro Azul S.A. de C.V.
BO.Paz Barahona
3 Ave.11 Calle S.O
San Pedro Sula, Honduras
TEL: (504) 553-2029
For Australia
Tel: (02) 9982 8266
For New Zealand
Tel: (09) 3098 715
BARBADOS
KOREA
GUATEMALA
Musique & Son
Z.I.Les Mangle
97232 Le Lamantin
Martinique F.W.I.
TEL: 596 596 426860
Parsons Music Ltd.
8th Floor, Railway Plaza, 39
Chatham Road South, T.S.T,
Kowloon, HONG KONG
TEL: 2333 1863
PT Citra IntiRama
J1. Cideng Timur No. 15J-150
Jakarta Pusat
INDONESIA
TEL: (021) 6324170
OMNI MUSIC
75 Avenida Norte y Final
Alameda Juan Pablo II,
Edificio No.4010 San Salvador,
EL SALVADOR
TEL: 262-0788
MARTINIQUE
ARGENTINA
INDONESIA
EL SALVADOR
38 Campbell Avenue
Dee Why West. NSW 2099
AUSTRALIA
Tom Lee Music Co., Ltd.
Service Division
22-32 Pun Shan Street, Tsuen
Wan, New Territories,
HONG KONG
TEL: 2415 0911
Rivera Digitec (India) Pvt. Ltd.
409, Nirman Kendra
Mahalaxmi Flats Compound
Off. Dr. Edwin Moses Road,
Mumbai-400011, INDIA
TEL: (022) 2493 9051
DOMINICAN REPUBLIC
Instrumentos Musicales S.A.
Av.Santa Fe 2055
(1123) Buenos Aires
ARGENTINA
TEL: (011) 4508-2700
A&B Music Supplies LTD
12 Webster Industrial Park
Wildey, St.Michael, Barbados
TEL: (246)430-1100
Roland Brasil Ltda.
Rua San Jose, 780 Sala B
Parque Industrial San Jose
Cotia - Sao Paulo - SP, BRAZIL
TEL: (011) 4615 5666
CHILE
Comercial Fancy II S.A.
Rut.: 96.919.420-1
Nataniel Cox #739, 4th Floor
Santiago - Centro, CHILE
TEL: (02) 688-9540
COLOMBIA
Centro Musical Ltda.
Cra 43 B No 25 A 41 Bododega 9
Medellin, Colombia
TEL: (574)3812529
COSTA RICA
JUAN Bansbach Instrumentos
Musicales
Ave.1. Calle 11, Apartado
10237,
San Jose, COSTA RICA
TEL: 258-0211
Gigamusic SARL
10 Rte De La Folie
97200 Fort De France
Martinique F.W.I.
TEL: 596 596 715222
MEXICO
Casa Veerkamp, s.a. de c.v.
Av. Toluca No. 323, Col. Olivar
de los Padres 01780 Mexico
D.F. MEXICO
TEL: (55) 5668-6699
NICARAGUA
Bansbach Instrumentos
Musicales Nicaragua
Altamira D'Este Calle Principal
de la Farmacia 5ta.Avenida
1 Cuadra al Lago.#503
Managua, Nicaragua
TEL: (505)277-2557
PANAMA
SUPRO MUNDIAL, S.A.
Boulevard Andrews, Albrook,
Panama City, REP. DE
PANAMA
TEL: 315-0101
PARAGUAY
Distribuidora De
Instrumentos Musicales
J.E. Olear y ESQ. Manduvira
Asuncion PARAGUAY
TEL: (595) 21 492147
PERU
Audionet
Distribuciones Musicales SAC
Juan Fanning 530
Miraflores
Lima - Peru
TEL: (511) 4461388
TRINIDAD
AMR Ltd
Ground Floor
Maritime Plaza
Barataria Trinidad W.I.
TEL: (868) 638 6385
EUROPE
AUSTRIA
Roland Elektronische
Musikinstrumente HmbH.
Austrian Office
Eduard-Bodem-Gasse 8,
A-6020 Innsbruck, AUSTRIA
TEL: (0512) 26 44 260
BELGIUM/FRANCE/
HOLLAND/
LUXEMBOURG
Roland Central Europe N.V.
Houtstraat 3, B-2260, Oevel
(Westerlo) BELGIUM
TEL: (014) 575811
CROATIA
ART-CENTAR
Degenova 3.
HR - 10000 Zagreb
TEL: (1) 466 8493
CZECH REP.
CZECH REPUBLIC
DISTRIBUTOR s.r.o
Voctárova 247/16
CZ - 180 00 PRAHA 8,
CZECH REP.
TEL: (2) 830 20270
DENMARK
Roland Scandinavia A/S
Nordhavnsvej 7, Postbox 880,
DK-2100 Copenhagen
DENMARK
TEL: 3916 6200
FINLAND
Roland Scandinavia As, Filial
Finland
Elannontie 5
FIN-01510 Vantaa, FINLAND
TEL: (0)9 68 24 020
GERMANY
Roland Elektronische
Musikinstrumente HmbH.
Oststrasse 96, 22844
Norderstedt, GERMANY
TEL: (040) 52 60090
GREECE/CYPRUS
STOLLAS S.A.
Music Sound Light
155, New National Road
Patras 26442, GREECE
TEL: 2610 435400
HUNGARY
Roland East Europe Ltd.
Warehouse Area ‘DEPO’ Pf.83
H-2046 Torokbalint,
HUNGARY
TEL: (23) 511011
IRELAND
Roland Ireland
G2 Calmount Park, Calmount
Avenue, Dublin 12
Republic of IRELAND
TEL: (01) 4294444
ITALY
Roland Italy S. p. A.
Viale delle Industrie 8,
20020 Arese, Milano, ITALY
TEL: (02) 937-78300
PORTUGAL
KUWAIT
LEBANON
Roland Iberia, S.L.
Portugal Office
Cais das Pedras, 8/9-1 Dto
4050-465, Porto, PORTUGAL
TEL: 22 608 00 60
Chahine S.A.L.
Gerge Zeidan St., Chahine
Bldg., Achrafieh, P.O.Box: 165857
Beirut, LEBANON
TEL: (01) 20-1441
ROMANIA
OMAN
FBS LINES
Piata Libertatii 1,
535500 Gheorgheni,
ROMANIA
TEL: (266) 364 609
TALENTZ CENTRE L.L.C.
Malatan House No.1
Al Noor Street, Ruwi
SULTANATE OF OMAN
TEL: 2478 3443
RUSSIA
QATAR
MuTek
Dorozhnaya ul.3,korp.6
117 545 Moscow, RUSSIA
TEL: (095) 981-4967
Al Emadi Co. (Badie Studio &
Stores)
P.O. Box 62, Doha, QATAR
TEL: 4423-554
SLOVAKIA
SAUDI ARABIA
DAN Acoustic s.r.o.
Povazská 18.
SK - 940 01 Nové Zámky
TEL: (035) 6424 330
SPAIN
aDawliah Universal
Electronics APL
Corniche Road, Aldossary
Bldg., 1st Floor, Alkhobar,
SAUDI ARABIA
Roland Iberia, S.L.
Paseo García Faria, 33-35
08005 Barcelona SPAIN
TEL: 93 493 91 00
P.O.Box 2154, Alkhobar 31952
SAUDI ARABIA
TEL: (03) 898 2081
SWEDEN
SYRIA
Roland Scandinavia A/S
SWEDISH SALES OFFICE
Danvik Center 28, 2 tr.
S-131 30 Nacka SWEDEN
TEL: (0)8 702 00 20
SWITZERLAND
Roland (Switzerland) AG
Landstrasse 5, Postfach,
CH-4452 Itingen,
SWITZERLAND
TEL: (061) 927-8383
Technical Light & Sound
Center
Rawda, Abdul Qader Jazairi St.
Bldg. No. 21, P.O.BOX 13520,
Damascus, SYRIA
TEL: (011) 223-5384
TURKEY
ZUHAL DIS TICARET A.S.
Galip Dede Cad. No.37
Beyoglu - Istanbul / TURKEY
TEL: (0212) 249 85 10
U.A.E.
UKRAINE
EURHYTHMICS Ltd.
P.O.Box: 37-a.
Nedecey Str. 30
UA - 89600 Mukachevo,
UKRAINE
TEL: (03131) 414-40
Zak Electronics & Musical
Instruments Co. L.L.C.
Zabeel Road, Al Sherooq Bldg.,
No. 14, Grand Floor, Dubai,
U.A.E.
TEL: (04) 3360715
UNITED KINGDOM
Roland (U.K.) Ltd.
Atlantic Close, Swansea
Enterprise Park, SWANSEA
SA7 9FJ,
UNITED KINGDOM
TEL: (01792) 702701
MIDDLE EAST
BAHRAIN
NORTH AMERICA
CANADA
Roland Canada Ltd.
(Head Office)
5480 Parkwood Way
Richmond B. C., V6V 2M4
CANADA
TEL: (604) 270 6626
Moon Stores
No.16, Bab Al Bahrain Avenue,
P.O.Box 247, Manama 304,
State of BAHRAIN
TEL: 17 211 005
Roland Canada Ltd.
(Toronto Office)
170 Admiral Boulevard
Mississauga On L5T 2N6
CANADA
TEL: (905) 362 9707
IRAN
U. S. A.
MOCO INC.
No.41 Nike St., Dr.Shariyati Ave.,
Roberoye Cerahe Mirdamad
Tehran, IRAN
TEL: (021) 285-4169
Roland Corporation U.S.
5100 S. Eastern Avenue
Los Angeles, CA 90040-2938,
U. S. A.
TEL: (323) 890 3700
ISRAEL
Halilit P. Greenspoon & Sons
Ltd.
8 Retzif Ha'aliya Hashnya St.
Tel-Aviv-Yafo ISRAEL
TEL: (03) 6823666
As of November 1, 2006 (ROLAND)
HP201_e.book 50 ページ 2007年1月15日 月曜日 午後5時37分
For EU Countries
This product complies with the requirements of European Directives EMC 89/336/EEC and LVD 73/23/EEC.
For the USA
FEDERAL COMMUNICATIONS COMMISSION
RADIO FREQUENCY INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.
Unauthorized changes or modification to this system can void the users authority to operate this equipment.
This equipment requires shielded interface cables in order to meet FCC class B Limit.
For Canada
NOTICE
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
AVIS
Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.
For the USA
DECLARATION OF CONFORMITY
Compliance Information Statement
Model Name :
Type of Equipment :
Responsible Party :
Address :
Telephone :
HP201
Digital Piano
Roland Corporation U.S.
5100 S. Eastern Avenue, Los Angeles, CA 90040-2938
(323) 890-3700
Cover1,4
*
0
4
5
6
4
7
2
3
04564723
-
0
1
*
07-01-1N
DIC449
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement