null  Specification
VIDEO CASSETTE RECORDER
HR-J4010UM
INSTRUCTIONS
LPT0793-001A
COPYRIGHT © 2003 VICTOR COMPANY OF JAPAN, LTD.
Dear Customer,
Thank you for purchasing the JVC VHS video cassette recorder.
Before use, please read the safety information and precautions to
ensure safe use of your new VCR.
CAUTIONS
WARNING: DANGEROUS VOLTAGE INSIDE
WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO
NOT EXPOSE THIS UNIT TO RAIN OR
MOISTURE.
UM
Printed in Thailand
J4F12701A K
03/02
0203-AH-OR-OR
CAUTION
■ When you are not using the VCR for a long period of time, it is
recommended that you disconnect the power cord from the
AC outlet.
■ Dangerous voltage inside. Refer internal servicing to qualified
service personnel. To prevent electric shock or fire hazard,
remove the power cord from the AC outlet prior to
connecting or disconnecting any signal lead or aerial.
■ Changes or modifications not approved by JVC could void
user’s authority to operate the equipment.
The POWER
/l button does not completely shut off mains
power from the unit, but switches operating current on and off.
“ ” shows electrical power standby and “ l ” shows ON.
This unit is produced to comply with Standard IEC 60065.
• Cassettes marked “VHS” (or “S-VHS”) can be used with this video
cassette recorder. However, S-VHS recording is not possible with
this model.
• This model is equipped with SQPB (S-VHS QUASI PLAYBACK)
that makes it possible to play back S-VHS recordings with
regular VHS resolution.
• HQ VHS is compatible with existing VHS equipment.
POWER SYSTEM:
This set operates on voltage of AC 110 – 220V~, 50/60 Hz with
automatic switching.
Use the conversion plug (provided) depending on the type of
your AC WALL outlet.
The rating plate and safety caution are on the rear of the unit.
IMPORTANT:
It may be unlawful to record or play back copyrighted material
without the consent of the copyright owner.
4F12701AE Cov-07
1
30/1/03, 5:04 PM
When the equipment is installed in a cabinet or a shelf, make sure
that it has sufficient space on all sides to allow for ventilation
(10 cm or more on both sides, on top and at the rear).
When discarding batteries, environmental problems must be
considered and the local rules or laws governing the disposal of
these batteries must be followed strictly.
Failure to heed the following precautions may result in damage
to the VCR, Remote or video cassette.
1. DO NOT place the VCR ...
... in an environment prone to extreme temperatures or humidity.
... in direct sunlight.
... in a dusty environment.
... in an environment where strong magnetic fields are generated.
... on a surface that is unstable or subject to vibration.
2. DO NOT block the VCR’s ventilation openings or holes.
(If the ventilation openings or holes are blocked by a newspaper
or cloth, etc., the heat may not be able to get out.)
3. DO NOT place heavy objects on the VCR or Remote.
4. DO NOT place anything which might spill on top of the VCR or
Remote.
(If water or liquid is allowed to enter this equipment, fire or electric
shock may be caused.)
5. DO NOT expose the apparatus to dripping or splashing.
6. DO NOT use this equipment in a bathroom or places with water.
Also DO NOT place any containers filled with water or liquids
(such as cosmetics or medicines, flower vases, potted plants, cups,
etc.) on top of this unit.
7. DO NOT place any naked flame sources, such as lighted candles,
on the apparatus.
8. AVOID violent shocks to the VCR during transport.
4F12701AE Cov-07
2
MOISTURE CONDENSATION
Moisture in the air will condense on the VCR when you move it
from a cold place to a warm place, or under extremely humid
conditions—just as water droplets form on the surface of a glass
filled with cold liquid. Moisture condensation on the head drum will
cause damage to the tape. In conditions where condensation may
occur, keep the VCR’s power turned on for a few hours to let the
moisture dry.
How to use the Remote
Before use, insert two AAA size batteries into the Remote with the
polarity ( and ) matched correctly as indicated on the battery
compartment or on the lid.
● Point the Remote toward the remote sensor on the target
component.
● The maximum operating distance of the remote control is about 5 m.
NOTE:
If the Remote does not work properly, remove its batteries, wait for
a few seconds, replace the batteries and then try again.
Video heads cleaning
The heads get dirty in the following cases:
● in an environment prone to extreme temperature or humidity.
● in a dusty environment
● flaw, dirt or mold on video tapes
● continuous usage for a long time
Use a dry cleaning cassette — TCL-2 — when:
● Rough, poor picture appears while a tape is played back.
● The picture is unclear or no picture appears.
30/1/03, 5:04 PM
Buttons, Connectors and Indicators
Front Panel
POWER
Cassette loading slot
CH–/+
REC
PLAY
PLAY
POWER
VIDEO
AUDIO
STOP/EJECT
TV/VCR
VIDEO/AUDIO input
connectors
TIMER
TV/VCR indicator
TIMER indicator
REC
POWER
CH
REW
Remote sensor
REW
POWER indicator
REC indicator
FF
REC
FF
STOP/EJECT
Rear Panel
AC power cord
UHF/VHF IN (ANT)
UHF/VHF
IN(ANT)
OUT
VIDEO
AUDIO OUT(TV)
CH
3
4
AUDIO/VIDEO OUT
3/4 CHANNEL
SELECTTOR SWITCH
UHF/VHF OUT (TV)
4F12701AE Cov-07
3
30/1/03, 5:04 PM
– Buttons, Connectors and Indicators –
Connections and VCR channel
Setting
Remote
POWER
POWER
Number keys
AUX
REC
1
1
2
3
4
5
6
7
8
9
–
0 (AUX)
PAUSE
Situate VCR
3
Connect VCR to TV
PAUSE
PLAY
REW
STOP
2
Place the VCR on a stable, horizontal surface.
+
CH
REC
CH–/+
Check contents
Make sure the package contains all of the accessories listed
in “Specifications”.
PLAY
REW
FF
Antenna or cable
Coaxial cable
FF
ENTER
MENU
MENU
SET–/+
ENTER
STOP
– SET +
TV/VCR
TV/VCR
CANCEL
C.RESET
TIMER
SP/EP
DISPLAY
Flat feeder
TIMER
CANCEL
C.RESET
SP/EP
Matching transformer
(not supplied)
UHF/VHF
IN(ANT)
TV POWER
TV POWER
–
TV CH
+
INPUT
–
TV VOL
+
DISPLAY
AC power cord
OUT
VIDEO
TV CH–/+
INPUT
AUDIO OUT(TV)
TV VOL–/+
CH
UHF/VHF
OUT
IN(ANT)
VIDEO
3
4
L
AUDIO
OUT(TV)
R
This Remote transmit A code
signals only; it is not applicable
to B code signals.
AC outlet
On-screen display
To audio/video input connectors
Back of VCR
If you press DISPLAY on the Remote, you can see the current VCR
status on the TV screen. Press DISPLAY again to exit on-screen
display.
The indications are not recorded even if the VCR is in the recording
mode.
TV
WHILE WATCHING TV
DAY AND CLOCK TIME
8 : 30 AM THU
CH 125
CHANNEL
TAPE
SPEED
REAL TIME COUNTER
00 : 00 : 00 SP
WHILE OPERATING A TAPE
OPERATING MODE
8 : 30 AM THU
CH 125
AUTO REPEAT
AUTO TRACKING
TAPE IN
AUTO TR.
00 : 00 : 00 SP
4F12701AE Cov-07
Audio/video cable
(not supplied)
4
To 75 Ω terminal
RF cable
(supplied)
RF Connection
1 Disconnect the TV antenna from the TV.
2 Connect the TV antenna cable to the UHF/VHF IN
terminal on the rear of the VCR.
3 Connect the supplied RF cable between the UHF/VHF
OUT terminal on the rear of the VCR and the TV’s
antenna input terminal.
AV Connection
(improves picture quality during tape playback.)
If your TV is equipped with audio/video input connectors
1 Connect the antenna, VCR and TV as shown in the
illustration.
2 Connect an audio/video cable between the AUDIO/
VIDEO OUT connectors on the rear of the VCR and the
audio/video input connectors on the TV.
• Even if you are using audio/video cables to connect your
VCR to your TV, you must also connect it using the RF
cable. This will ensure that you can record one show while
watching another.
30/1/03, 5:04 PM
– Connections and VCR channel Setting –
4
Initial Settings
Set VCR channel
To view playback of a recorded tape, or to watch a program
selected by the VCR's channel selector, the TV must be set to
channel 3 or 4 (video channel) when a TV is connected with
the 75 ohm coaxial cable only.
Language Setting
The default setting is “ESPAÑOL”.
1
1 Set the 3/4 Channel selector switch (Rear of the VCR) to
CH 3 or 4.
2 Turn ON the TV and set to CH 3 or 4 to correspond with
the channel selected in 1.
Access Menu screen, then
Language screen
Press MENU on the Remote. Press
SET –/+ to select “LANGUAGE”, then
press ENTER.
MENU
CLOCK SET
TIMER REC SET
AUTO REPEAT ON OFF
CH SET UP
LANGUAGE/IDIOMA/LANGUE
NO NOISE BACKGROUND
ON OFF
〈+/—/ENTER/MENU〉
LANGUAGE/IDIOMA/LANGUE
3
4
5
Press POWER to turn on the VCR.
The POWER indicator will light.
Press TV/VCR to select the VCR
position.
The TV/VCR indicator will light.
Select any channel to receive a
TV station in your area.
The channel number will appear
on the screen for about 4 seconds.
2
CAN 125
Select language
ENGLISH
ESPAÑOL
This VCR offers you the language
FRANCAIS
choice to view menus and some
〈+/–/ENTER/MENU〉
messages — in English, Spanish or
French. Press SET –/+ to select your desired language, then
press ENTER.
Press MENU twice to return to normal screen.
Clock Setting
Preparations
You must set the date and time for timer recording.
1
Access Menu screen, then Clock
Set screen
Press MENU on the Remote. Press
SET –/+ to select “CLOCK SET”, then
press ENTER.
2
Set month, day, year and time
Press SET –/+ until the desired month
appears, then press ENTER. Set the
day, year and time in the same way.
MENU
CLOCK SET
TIMER REC SET
AUTO REPEAT ON OFF
CH SET UP
LANGUAGE/IDIOMA/LANGUE
NO NOISE BACKGROUND
ON OFF
〈+/—/ENTER/MENU〉
MONTH
3
DAY
YEAR
1 (WED)
2000
TIME
12 : 00 AM
〈+/—/ENTER/CANCEL/MENU〉
3
Start clock
MONTH
Press MENU twice and normal screen
appears.
DAY
YEAR
TIME
3
26 (WED)
2003
8 : 30 AM
〈+/—/ENTER/CANCEL/MENU〉
To make corrections any time during the process
Press CANCEL repeatedly until the item you want to change
blinks, then press SET –/+.
NOTE:
After a power failure or disconnection of the power over 18
hours, the timer settings will be lost. In this case, reset the
present time.
4F12701AE Cov-07
5
30/1/03, 5:05 PM
– Initial Settings –
Tuner Setting
This VCR is equipped with a channel memory feature which
allows channels to skip up or down to the next channel set
into memory, skipping over unwanted channels. Before
selecting channels, they must be programmed into the VCR’s
memory. In addition to normal VHF and UHF channels, this
VCR can receive up to 113 Cable TV channels. To use this
VCR with an antenna, set the TV/CATV menu option to the
TV mode. When shipped from the factory, this menu option
is in the CATV mode.
– TV/CATV Selection
1
Setting channels manually
– Manual Channel Set
You can add the channels you want or delete the channels
you do not want manually.
1
Press MENU on the Remote. Press
SET –/+ to select “CH SET UP”, then
press ENTER.
2
Access Menu screen, then CH
Set Up screen
Press MENU on the Remote. Press
SET –/+ to select “CH SET UP”, then
press ENTER.
MENU
CLOCK SET
TIMER REC SET
AUTO REPEAT ON OFF
CH SET UP
LANGUAGE/IDIOMA/LANGUE
NO NOISE BACKGROUND
ON OFF
Perform TV/CATV Selection
Press SET –/+ to select “TV/CATV”,
then press ENTER to select the TV
or CATV mode. The arrow indicates
the selected mode.
Access ADD/DELETE Mode
Press SET –/+ to select “ADD/
DELETE”, then press ENTER.
MENU
CLOCK SET
TIMER REC SET
AUTO REPEAT ON OFF
CH SET UP
LANGUAGE/IDIOMA/LANGUE
NO NOISE BACKGROUND
ON OFF
〈+/—/ENTER/MENU〉
CH SET UP
TV CATV
AUTO CH MEMORY
ADD/DELETE
〈+/–/ENTER/MENU〉
〈+/—/ENTER/MENU〉
3
2
Access Menu screen, then CH
Set Up screen
Add or Delete desired channels
ADD
CH 012
CH SET UP
1
TV CATV
AUTO CH MEMORY
ADD/DELETE
2
〈+/–/ENTER/MENU〉
TV
- VHF/UHF channels
CATV - CABLE TV channels
Press SET –/+ on the Remote to
select a channel number you
want to add or delete.
〈+/–/ENTER/MENU〉
To add channels
Press ENTER until “ADD” appears on the screen to set to
add the unmemorized channel.
To delete channels
Press ENTER until “DELETE” appears on the screen to set
to delete the channel from memory.
Press MENU twice to return to normal screen.
Repeat 1 to 2 to add or delete other channel.
Setting channels automatically
– Auto Channel Memory
3
The VCR can receive a maximum of
181 channels by presetting the
channels into memory.
NOTE: You can’t select “CH SET UP” if you set the channel
to “L”.
Access Menu screen, then CH
Set Up screen
Press MENU on the Remote. Press
SET –/+ to select “CH SET UP”, then
press ENTER.
1
2
Perform Auto Channel Memory
Press SET –/+ to select “AUTO CH
MEMORY”, then press ENTER.
MENU
CLOCK SET
TIMER REC SET
AUTO REPEAT ON OFF
CH SET UP
LANGUAGE/IDIOMA/LANGUE
NO NOISE BACKGROUND
ON OFF
Press MENU three times to return to normal screen.
〈+/—/ENTER/MENU〉
CH SET UP
TV CATV
AUTO CH MEMORY
ADD/DELETE
〈+/–/ENTER/MENU〉
3
Complete Auto Channel Memory
The auto tuning will start. The
channel display will count up and
when finished, the screen returns to
normal.
4F12701AE Cov-07
6
CH 001
30/1/03, 5:05 PM
Playback
Slow-motion
Press PLAY ( ) on the
OR Press Play (
Remote.
VCR.
• Playback will proceed at
1/10 th of the normal speed.
• Press PLAY ( ) to resume
normal playback.
Basic Playback
1 Load a cassette
) on the
PLAY
POWER
VIDEO
AUDIO
STOP/EJECT
TV/VCR
TIMER
REC
POWER
CH
REW
FF
REC
Make sure the window side is up, the rear
label side is facing you and the arrow on
the front of the cassette is pointing
towards the VCR.
• Do not apply too much pressure when
inserting.
• The VCR turns on, and the counter on
the on-screen display is reset, automatically.
• If the cassette’s record safety tab has been removed, playback
begins automatically.
2
Start playback
Press PLAY (
).
NOTE:
During slow motion picture, some noise might appear on
the TV screen. Use the SET–/+ on the Remote to eliminate
the noise.
Speed search
) or FF
) or
Press REW (
OR Press REW (
(
) on the Remote.
FF (
) on the VCR.
• Press PLAY ( ) to resume
normal playback.
Variable speed search
Press REW (
) or FF
OR Press REW (
) or FF
(
) repeatedly on the
(
) repeatedly on
Remote.
the VCR.
• Press PLAY ( ) to resume
normal playback.
• Each time you press REW
(
) or FF (
) the
playback speed changes.
During playback
TAPE SPEED
Stop playback
Press STOP (
Remote.
) on the
OR Press STOP/EJECT (■/
) on the VCR.
PICTURE SEARCH SPEED
PRESS ONCE
PRESS TWICE
SP
3X
5X
EP
9X
15X
When the tape is not running
Rewind/fast-forward
Press REW (
) or FF
) on the Remote.
(
) or FF
OR Press REW (
) on the VCR.
(
Pause playback and view still picture
Press PAUSE.
• Press PLAY ( ) to resume
normal playback.
Pause and Frame-by-Frame playback
Press PAUSE to pause, then
press PAUSE repeatedly.
Press PLAY ( ) to resume
normal playback.
Eject the tape
Press STOP/EJECT (■/ ) on
the VCR.
• You can also eject the
cassette when the VCR is
turned off.
Turn off the VCR
Press POWER on the
Remote.
4F12701AE Cov-07
7
30/1/03, 5:05 PM
OR Press POWER (
the VCR.
/l) on
– Playback –
Playback Features
Recording
Adjusting tracking condition
– Tracking Adjustment
It may be unlawful to record or play back copyrighted
material without the consent of the copyright owner.
Accidental erasure prevention
To prevent accidental recording on a recorded cassette,
remove its record safety tab. To record on
it later, cover the hole with adhesive
tape.
Automatic tracking adjustment
Whenever you insert a tape and start playback, automatic
tracking starts working and continuously analyzes the signal
to enable optimum picture quality during playback.
Manual tracking adjustment
If automatic tracking cannot eliminate noises well during
playback, press SET –/+ on the Remote to eliminate the
noises. Press it briefly for a fine adjustment, or press and
hold for a coarse adjustment.
• Press SP/EP on the Remote to reactivate automatic
tracking.
Playing back tape repeatedly
– Auto Repeat Play
1
Access Menu screen
Press MENU on the Remote.
Press SET –/+ to select “AUTO
REPEAT”.
MENU
CLOCK SET
TIMER REC SET
AUTO REPEAT ON OFF
CH SET UP
LANGUAGE/IDIOMA/LANGUE
NO NOISE BACKGROUND
ON OFF
〈+/—/ENTER/MENU〉
2
3
Select ON/OFF
Press ENTER to select “ON” or
“OFF”.
Press MENU to return to normal
screen.
Start Auto Repeat Play
Press PLAY. The tape will play
over and over until the repeat
mode is canceled.
MENU
CLOCK SET
TIMER REC SET
AUTO REPEAT ON OFF
CH SET UP
LANGUAGE/IDIOMA/LANGUE
NO NOISE BACKGROUND
ON OFF
〈+/—/ENTER/MENU〉
Record safety tab
Basic Recording
1 Load a cassette
Make sure the record safety tab is
intact. If not, cover the hole with
adhesive tape before inserting the
cassette.
• The VCR turns on, and the counter
is reset, automatically.
2 Select recording channel
CH 110
Press CH–/+ or the Number keys on
the Remote [CH–/+ on the VCR].
• If you connect the TV and the VCR
only using the RF connection, press
TV/VCR on the Remote so that the
TV/VCR indicator lights to view the program to be
recorded.
3
Set tape speed
Press SP/EP.
00 : 00 : 00 SP
4 Start recording
On the VCR, press REC. Or on the
Remote, while holding REC, press
PLAY ( ).
The REC indicator will light.
During recording
Pause recording
Press PAUSE.
• Press PAUSE to resume recording.
• You can select channel in the
recording pause mode.
Stop recording
Press STOP (
Remote.
4F12701AE 08-Back
8
) on the
30/1/03, 5:05 PM
OR Press STOP/EJECT
(■/ ) on the VCR.
CH 110
– Recording –
Recording Features
Timer Recording
Specifying recording length
- One Touch Timer Recording (OTR)
Timer recording can be programmed on-screen with
the remote control. The built-in timer allows automatic
unattended recording of up to 8 programs within 1
month.
The One-touch Timer Recording feature provides a
simple and convenient way to make a timed
recording.
EXAMPLE: One-touch Timer Recording for 30 minutes.
When a TV is connected with an audio/video cable, turn the
TV on and select the video input mode on the TV.
1
Load a cassette tape with the
erase prevention tab intact.
2
Press SP/EP to select the desired
tape speed SP or EP.
The counter and SP or EP will
appear on the screen for about 4
seconds.
Press the Number keys or CH –/+
to select the channel to be
recorded.
The channel number will appear
on the screen and display for
about 4 seconds.
4
Press REC on the VCR or while
holding REC, press PLAY ( ) on
the Remote to begin recording.
Press REC on the VCR again to
stop recording after 30 minutes.
Each additional press of REC will
increase recording time as shown
in the chart below, up to a
maximum of 5 hours. The OTR
and recording time will appear on
screen for about 4 seconds.
NOTES: • Press REC to increase
the time needed for
recording (See the
chart ).
• To cancel OTR, press
STOP ( ) or turn off
the power.
OTR 0 : 30
CH 125
Press Recording time
once
NORMAL REC
twice
0:30
3 times
1:00
4 times
1:30
5 times
2:00
6 times
3:00
7 times
4:00
8 times
5:00
9 times NORMAL REC
During recording…
• If you connect the TV and the VCR only using the RF
connection to view pictures from the VCR, press TV/VCR
on the Remote so that TV/VCR indicator goes off. (The TV
broadcast being recorded disappears.)
• If you are using the AV connection to view pictures from
the VCR, change the TV’s input mode from AV to TV.
Then, select the channel you want to watch, on the TV.
9
When a TV is connected with an audio/video cable, turn the
TV and this VCR on and select the video input mode on the
TV.
1
Press MENU on the Remote.
Check the “TIMER REC SET”
option is selected, then press
ENTER.
2
Press SET –/+ to select one
of the program lines, then
press ENTER.
CH 125
Watching one program while recording another
4F12701AE 08-Back
• After timer recording is completed, the VCR turns off
automatically.
• You can program the timer recording while a regular
recording is in progress; the menu screens will not be
recorded.
• The timer recording will start at 20 seconds before the
time you predetermined.
EXAMPLE: Program a timer recording for the 26th day,
channel 125 (CATV), 11:00 - 11:30 PM on timer program
number 1 (Tape speed: EP).
00 : 00 : 00 SP
3
NOTES:
3
Press SET –/+ to select the
date, then press ENTER.
4
Set the start time, end time,
channel and tape speed as in
step 3.
NOTE: To record from external
source, press SET –/+
and set the channel to
"L". "L" will appear
next to CH 125 (or 69).
5
To enter other programs,
repeat step 2 through 4. Or,
press MENU twice to return
to the normal screen.
6
Press TIMER on the Remote.
The power will go off, the
TIMER indicator will light and
the VCR stands by for
recording.
MENU
CLOCK SET
TIMER REC SET
AUTO REPEAT ON OFF
CH SET UP
LANGUAGE/IDIOMA/LANGUE
NO NOISE BACKGROUND
ON OFF
〈+/—/ENTER/MENU〉
DATE
START
END
CH
–––––
–––––
–––––
–––––
–––––
–––––
–––––
–––––
–:––
–:––
–:––
–:––
–:––
–:––
–:––
–:––
–:––
–:––
–:––
–:––
–:––
–:––
–:––
–:––
––
––
––
––
––
––
––
––
DATE
START
〈+/–/ENTER/CANCEL/MENU〉
26(SU)
------------------------------------
-:--:--:--:--:--:--:--:--
END
-:--:--:--:--:--:--:--:--
CH
-----------------
〈+/–/ENTER/CANCEL/MENU〉
To use the VCR while it is in timer recording standby mode
Press TIMER. After you use the VCR, press TIMER again
to put the VCR into timer recording standby mode.
30/1/03, 5:05 PM
–
–
–
–
–
–
–
–
-
– Timer Recordings –
TO CORRECT THE SETTINGS
IF THE PROGRAM OVERLAPS ANOTHER
When setting the Timer Recording, press ENTER until the
desired setting blinks, then re-enter the setting using SET –/+.
When finished, press ENTER.
NOTE: Do not overlap programs as portions of the
conflicting programs will be lost. The first
recording time has priority over the next recording
time as shown in the diagram.
NOTES: • The VCR cannot be used while the TIMER
indicator is lit.
• After a power failure or disconnection of the
power plug over 18 hours, all programmed
recording settings must be reset upon
resumption of power. In this case, reset the clock
and reprogram any timer recordings.
• Press CANCEL to move cursor backward for
correction.
TO SET DAILY/WEEKLY TIMER
When setting the date in step 3 in the Setting the Timer
Recording section on the previous page, press SET –
repeatedly.
The setting changes as follows:
8 : 00
9 : 00
One month later
minus one day
WKL-WE
(Weekly Wednesday)
Deleted Parts
Program 3
Non Recorded Portion Parts
Recording
Control Settings
Prog.1
MO-SA (Monday to Saturday)
MO-FR (Monday to Friday)
WKL-TH (Weekly Thursday)
TO CONFIRM THE SETTINGS
DATE START END CH
26 (WE) 11:00PM 11:30PM 125 EP
–––––
–––––
–––––
–––––
–––––
–––––
–––––
–:––
–:––
–:––
–:––
–:––
–:––
–:––
–:––
–:––
–:––
–:––
–:––
–:––
–:––
––
––
––
––
––
––
––
DATE
START
END
CH
–––––
–––––
–––––
–––––
–––––
–––––
–––––
–––––
–:––
–:––
–:––
–:––
–:––
–:––
–:––
–:––
–:––
–:––
–:––
–:––
–:––
–:––
–:––
–:––
––
––
––
––
––
––
––
––
〈+/–/ENTER/CANCEL/MENU〉
–
–
–
–
–
–
–
TO CANCEL A PROGRAM
Press the SET –/+ to select the
“TIMER REC SET” option in the
MENU. Then press SET –/+ to
select the unnecessary program,
and press CANCEL to cancel the
program.
4F12701AE 08-Back
10
〈+/–/ENTER/CANCEL/MENU〉
Prog.2
Prog.3
NOTES: • The everyday/every week recording can be made
continuously until the recording is canceled or
the tape reaches the end.
• During timer recording, the automatic rewinding
mechanism does not function.
SU-SA (Sunday to Saturday)
Press SET –/+ to select the
“TIMER REC SET” option in the
MENU. Then press ENTER to
display the timer program list.
Press MENU twice to return to
the normal screen.
11 : 00
Program 2
Example
The current day (Friday)
10 : 00
Program 1
–
–
–
–
–
–
–
–
30/1/03, 5:05 PM
Editing
Other Functions
BLUE BACK — ON/OFF
When this function is set to “ON”, the TV screen becomes all
blue in the following cases:
When receiving a channel not in use.
When stopping playback.
1
2
3
Press MENU on the remote. Press SET –/+ to select
“NO NOISE BACKGROUND”.
You can use your VCR as the playback or recording VCR.
You can use a camcorder as the playback VCR and your VCR
as the recording VCR. Refer also to the other components’
instruction manuals for connection and its operations.
1 Make connections
Example: When using this VCR as the playback VCR
Press ENTER to select “ON”.
Press MENU to return to normal screen.
This VCR (for playback)
JVC TV Remote Control
To AUDIO/VIDEO OUT
This Remote can control some functions (TV POWER,
INPUT, TV CH –/+ and TV VOL –/+) of a remote
controllable JVC TV without setting.
NOTE:
Audio/video cable
(not supplied)
• It’s not possible to operate a unit not equipped with a
remote sensor.
• This Remote can control a JVC TV only.
To audio/video input
Another VCR (for recording)
• When using this VCR as the recording VCR, connect this
VCR’s audio/video input connectors to the audio/video
output connectors on the other VCR. If the playback VCR
is monaural, connect the audio output connector on the
playback VCR to the left audio input connector on this
VCR.
2 Load cassettes
Insert the playback cassette into the playback VCR and the
cassette to be recorded on into the recording VCR.
3 Select input mode on recording VCR
Select the correct external input on the recording VCR.
On this VCR (when using this VCR as the recording VCR);
Select “L” — when connecting the other VCR to the audio/video
input connectors on the front panel.
Press O (AUX) or CH–/+ on the Remote [CH–/+ on the VCR].
4 Start playback
Press PLAY (
) on the playback VCR.
5 Start recording
Press REC on the recording VCR.
4F12701AE 08-Back
11
30/1/03, 5:05 PM
Before Requesting Service
Make sure by first checking the following points.
SYMPTOM
CAUSE
POSSIBLE SOLUTION
POWER
No power.
The AC power cord is not connected.
Although the power is on, it
does not operate.
Cassette is not inserted.
Connect the AC power cord to the AC
outlet.
Insert a video cassette.
Antenna connection is not correct.
Connect it correctly.
Antenna cable is disconnected.
Reconnect the antenna cable.
The video channel is not in the correct
position.
Set it to CH 3 or 4.
The TV is not set to the video channel
3 or 4.
Set the TV channel selector to the 3 or 4
position.
The TV/VCR selector is set at TV mode
(The TV/VCR indicator is not lit).
Press the TV/VCR selector button (The TV/
VCR indicator will light).
INPUT is set to the LINE mode.
Press the Number key or CH –/+ button to
select your desired TV program.
The erase prevention tab of the video
cassette is broken off.
Place a piece of vinyl tape over the gap.
INPUT is set to the LINE mode.
Press the Number key or CH –/+ button to
select your desired TV program.
Reset the present time.
TV BROADCAST RECEPTION
A TV program that is selected by
the VCR does not appear on the
screen.
RECORDING
TV recording does not work.
The time is not set correctly.
Timer recording does not work.
The recording start/end time is not set
correctly.
Set the start/end time.
The TIMER button has not been
pressed (The TIMER indicator is not lit).
Press the TIMER button (The TIMER
indicator is lit).
The TV is not set to the video channel 3
or 4.
Set to the video channel 3 or 4 or
adjust the fine tuning button on your
TV set.
Tracking adjustment beyond range of
automatic tracking circuit.
Adjust tracking manually using the SET – or
+ buttons on the remote control.
Video heads are dirty.
The tape is worn or damaged.
Have the video heads cleaned.
Try another tape.
It is not aimed at the remote sensor.
Aim it at the remote sensor.
Distance too far or too much light in
the room.
Operate within 15 feet (5 meters) reduce
the light in the room.
There is an obstacle in the path of the
beam.
Clear the path of the beam.
The batteries are weak.
Replace the batteries.
The +, – polarity of the batteries are
not inserted correctly.
Insert correctly.
The TV/VCR function is in the VCR
mode.
Set to TV, or turn off the VCR power
button.
PLAYBACK
No picture on screen when
playing back a recorded tape.
Noise bars on screen.
REMOTE CONTROL
Remote control does not work.
TV programs cannot be seen
using the TV selector.
4F12701AE 08-Back
12
30/1/03, 5:05 PM
Specifications
GENERAL
Power requirement
Power consumption
Power on
Power off
Temperature
Operating
Storage
Operating position
Dimensions (W x H x D)
Weight
Format
Maximum recording time
SP
EP
:
AC 110 V-220 V~, 50Hz/60 Hz
:
:
9W
2.0 W
:
:
:
:
:
:
5°C to 40°C (41°F to 104°F)
–20°C to 60°C (–4°F to140°F)
Horizontal only
360 mm x 95 mm x 224 mm
3.2 kg
VHS NTSC standard
:
:
210 min. with ST-210 video cassette
630 min. with ST-210 video cassette
:
NTSC-type color signal and EIA monochrome signal, 525 lines/60 fields
:
:
:
DA-4 (Double Azimuth) head helical scan system
42 dB
230 lines
:
:
100 Hz to 10,000 Hz
RCA connectors (IN x 1, OUT x 1)
:
Frequency-synthesized tuner
:
:
:
:
Channels 2–13
Channels 14–69
113 Channels
Channel 3 or 4 (switchable; preset to Channel 3 when shipped) 75 ohms,
unbalanced
VIDEO/AUDIO
Signal system
Recording/Playback
system
Signal-to-noise ratio
Horizontal resolution
Frequency range
Normal audio
Input/Output
TUNER
Tuning system
Channel coverage
VHF
UHF
CATV
RF output
TIMER
:
Clock reference
:
Program capacity
Memory backup for timer :
Quartz
1-month programmable timer/8 programs
Approx. 18 hours
ACCESSORIES
:
Provided accessories
RF cable (F-type), Infrared remote control unit, “AAA” battery x 2, Conversion plug
Specifications shown are for SP mode unless specified otherwise.
E. & O.E. Design and specifications subject to change without notice.
4F12701AE 08-Back
13
30/1/03, 5:05 PM
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement