Samsung | AV-R720 | Instruction manual | Samsung AV-R720 Home Theater System User Manual

Digital Surround
AV Receiver System
AV-R720
HT-AS720
THIS APPLIANCE IS MANUFACTURED BY:
Instruction Manual
AH68-01989B
Safety Warnings
GB
Precautions
PREPARATION
Use of controls, adjustments or performance of procedures other than
those specified herein may result in hazardous radiation exposure.
CLASS 1 LASER PRODUCT
KLASSE 1 LASER PRODUKT
LUOKAN 1 LASER LAITE
KLASS 1 LASER APPARAT
PRODUCTO LASER CLASE 1
CAUTION-INVISIBLE LASER RADIATION WHEN OPEN
AND INTERLOCKS DEFEATED, AVOID
EXPOSURE TO BEAM.
This symbol indicates that dangerous voltage which
can cause electric shock is present inside this unit.
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT OPEN
This symbol alerts you to important operating and
maintenance instructions accompanying the unit.
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO
NOT REMOVE REAR COVER. NO USER
SERVICEABLE PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
WARNING: To reduce the risk of fire or electric shock, do not
expose this appliance to rain or moisture.
Ensure that the AC power supply in your house complies with the identification sticker located on the back of your player. Install
your player horizontally, on a suitable base (furniture), with enough space around it for ventilation (7.5~10cm). Make sure
the ventilation slots are not covered. Do not stack anything on top of the amplifier. In order to disconnect the player completely
from the power supply, remove the mains plug from the wall outlet, especially when left unused for a long period of time.
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE
BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
CLASS 1 LASER PRODUCT
This Compact Disc player is classified as a CLASS 1 LASER product.
• This apparatus shall always be connected to a AC outlet with a protective grounding connection.
• To disconnect the apparatus from the mains, the plug must be pulled out from the mains socket, therefore the mains
plug shall be readily operable.
Wiring the Main Power Supply Plug(UK Only)
IMPORTANT NOTICE
The main lead on this equipment is supplied with a moulded plug incorporating a fuse. The value of the fuse is indicated on the pin face of the plug
and if it requires replacing, a fuse approved to BS1362 of the same rating must be used.
Never use the plug with the fuse cover removed. If the cover is detachable and a replacement is required, it must be of the same colour as the fuse
fitted in the plug. Replacement covers are available from your dealer.
If the fitted plug is not suitable for the power points in your house or the cable is not long enough to reach a power point, you should obtain a suitable
safety approved extension lead or consult your dealer for assistance.
However, if there is no alternative to cutting off the plug, remove the fuse and then safely dispose of the plug. Do not connect the plug to a main
socket as there is a risk of shock hazard from the bared flexible cord.
Never attempt to insert bare wires directly into a main socket. A plug and fuse must be used at all times.
During thunderstorms, disconnect AC main plug from
the wall outlet.
Voltage peaks due to lightning could damage the unit.
Do not expose the unit to direct sunlight or other heat
sources.
This could lead to overheating and malfunction of
the unit.
Protect the player from moisture(i.e. vases) , and excess
heat(e.g.fireplace) or equipment creating strong magnetic
or electric fields (i.e.speakers...). Disconnect the power
cable from the AC supply if the player malfunctions. Your
player is not intended for industrial use.
Use of this product is for personal use only.
Condensation may occur if your player or disc have been
stored in cold temperatures.
If transporting the player during the winter, wait
approximately 2 hours until the unit has reached room
temperature before using.
The battery used with this product contain chemicals
that are harmful to the environment.
Do not dispose of batteries in the general household
trash.
IMPORTANT
The wires in the main lead are coloured in accordance with the following code:–
BLUE = NEUTRAL
BROWN = LIVE
As these colours may not correspond to the coloured markings identifying the terminals in your plug, proceed as follows:–
The wire coloured BLUE must be connected to the terminal marked with the letter N or coloured BLUE or BLACK. The wire coloured
BROWN must be connected to the terminal marked with the letter L or coloured BROWN or RED.
WARNING: DO NOT CONNECT EITHER WIRE TO THE EARTH TERMINAL WHICH IS MARKED WITH THE
LETTER E OR BY THE EARTH SYMBOL
, OR COLOURED GREEN OR GREEN AND YELLOW.
2
This marking shown on the product or its literature, indicates that it should not
be disposed with other household wastes at the end of its working life.
To prevent possible harm to the environment or human health from uncontrolled
waste disposal, please separate this from other types of wastes and recycle it
responsibly to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this
product, or their local government office, for details of where and how they
can take this item for environmentally safe recycling.
Business users should contact their supplier and check the terms and
conditions of the purchase contract.
This product should not be mixed with other commercial wastes for disposal.
3
Features
Contents
PREPARATION
This product is a pure digital AV receiver that performs digital signal processing to minimise
signal distortion and loss.
Safety Warnings ..............................................................................................................2
Precautions......................................................................................................................3
Features ..........................................................................................................................4
Description ......................................................................................................................6
Dolby Pro Logic IIx is a new technology that provides discrete 7.1 channel out of 2 channel
or multi channel sources.It also provides Music,Movie and Game modes.
DTS 96/24
DTS is a surround format that implements 5.1 channel multi channel sound at 96KHz/24bit.
In addition, it can also reproduce the matrix 6.1 of DTS 96/24 decorder signals.
PREPARATION
Digital AV Receiver
Dolby Pro Logic llx
GB
CONNECTIONS
Connecting the speakers.................................................................................................10
Connecting external devices ...........................................................................................12
Anynet+ ...........................................................................................................................16
Connecting the FM antennas ..........................................................................................17
OPERATION
DOLBY DIGITAL EX
Adds a surround back channel for more spacious sound compared to regular 5.1 channel
Dolby Digital.
DTS (Digital Theater Systems)
DTS plays back 5.1 channel sound with less compression than Dolby Digital for richer sound.
DTS-ES (Extended Surround)
DTS-ES adds an additional rear center surround channel for 6.1 channel sound.
It is compatible with existing DTS Digital Sound formats.
DTS
Reproduces digital PCM or analogue stereo over 6.1 channel using a high precision
DTS digital matrix.
Before using the AV receiver ...........................................................................................18
Selecting digital/analogue input ......................................................................................19
Setting the speaker mode................................................................................................20
Setting the speaker listening distance ...........................................................................22
Setting digital input ..........................................................................................................23
Setting HDMI AUDIO.......................................................................................................24
Setting DRC (Dynamic Range Compression) .................................................................25
Test tone .........................................................................................................................26
Setting speaker level .......................................................................................................28
Dolby Pro Logic llx mode.................................................................................................29
Setting Dolby Pro Logic llx effect ....................................................................................30
Setting NEO:6 mode........................................................................................................31
Setting EX/ES mode........................................................................................................32
Setting Tone Control ........................................................................................................33
SFE mode........................................................................................................................34
Stereo mode ....................................................................................................................35
RADIO OPERATION
Provides more realistic surround sound with normal stereo audio sources.
Listening to radio ............................................................................................................36
Presetting radio stations .................................................................................................37
About RDS broadcasting .................................................................................................38
Anynet+ (HDMI-CEC) Function
MISCELLANEOUS
Anynet+ is a function that can be used to operate this AV Receiver with a Samsung TV
remote control, by connecting the receiver to a SAMSUNG TV using an HDMI Cable.
(This function is available only in connection with Samsung TV and DVD player supporting
Anynet +(HDMI-CEC).)
Convenient functions ......................................................................................................40
Operating your TV with the remote control......................................................................43
Operating your DVD (VCR) with the remote control........................................................45
Before calling for service .................................................................................................47
Specifications ..................................................................................................................49
SFE (Sound Field Effect) Using 24bit Audio Digital Signal Processing
4
5
GB
Description
TONE CONTROL button
POWER STANDBY Indicator
POWER button
Remote control sensor SURROUND button
AUX IN Jack
HEADPHONE Jack
CD AUDIO INPUT JACKS HDMI OUTPUT JACK
VCR AUDIO
VCR VIDEO INPUT JACK
FM ANTENNA JACK
INPUT JACKS
VCR VIDEO OUTPUT JACK
HDMI INPUT
7.1 CH ANALOG
JACKS
FRONT SPEAKER TERMINALS
AUDIO INPUT JACKS
SURROUND SPEAKER TERMINALS
7.1CH IN STEREO button
VOLUME CONTROL
FUNCTION button
INPUT MODE button
SETUP button
TUNING MODE button
SELECT( , ) button
CENTER SPEAKER TERMINALS SURROUND BACK SPEAKER
TERMINALS
MONITOR VIDEO OUTPUT JACK
DVD VIDEO INPUT JACK
SAT(Cable/Satellite/Set-top box) VIDEO INPUT JACK
SUBWOOFER AUDIO OUTPUT JACK
DVD OPTICAL DIGITAL
AUDIO INPUT JACK
[ Display ]
SAT (Anynet+)
OPTICAL AUDIO INPUT JACK
CD COAXIAL DIGITAL
AUDIO INPUT JACK
DOLBY DIGITAL EX INDICATOR
SPEAKER INDICATORS
PREPARATION
[ Rear panel ]
[ Front panel ]
VCR AUDIO OUTPUT JACKS
DVD AUDIO INPUT JACKS
DIGITAL LIVE SURROUND
INDICATOR INDICATOR
L.PCM INDICATOR
SAT AUDIO INPUT JACKS
RADIO
BROADCASTING
RECEIVING INDICATOR
√√ Accessories œœ
RADIO FREQUENCY
INDICATOR
FRONT DISPLAY
RADIO STEREO INDICATORS
Remote control
FM antenna
User’s manual
DTS INDICATOR
6
7
GB
Description (Cont'd)
PREPARATION
[ Remote control ]
Insert remote control batteries
TV button
AMP button
DVD button
VCR button
DIMMER button
POWER button
NUMBER (0~9) buttons
SLEEP button
SUBWOOFER button
EX/ES button
1
TV/VIDEO, FUNCTION button
CD button
VCR button
DVD button
Remove the battery
cover in the direction
of the arrow.
2
Insert two 1.5V AAA
batteries, paying
attention to the correct
polarities (+ and –).
3
Replace the battery
cover.
7.1 CH button
SAT button
AUX button
INPUT MODE button
MO/ST button
TUNER button
EXTERNAL DEVICE PLAYBACK button
MUTE button
VOLUME CONTROL button
SETUP/MENU button
TUNING/CHANNEL button
TUNING MODE button
NEO : 6 MODE button
STEREO button
Range of operation of the remote control
The remote control can be used up to approximately 23 feet/7 meters in a straight line. It can also be operated
at a horizontal angle of up to 30° from the remote control sensor.
CURSOR/ENTER button
DRC button
INFO button
Follow these precautions to avoid leaking or cracking batteries:
• Place batteries in the remote control so they match the polarity:(+) to (+)and (–)to (–).
• Use the correct type of batteries. Batteries that look similar may differ in voltage.
• Always replace both batteries at the same time.
• Do not expose batteries to heat or flame.
TUNER MEMORY button
MODE button
EFFECT button
TEST TONE button
RDS selection buttons
SPK LEVEL button
SPK SELECT button
SFE MODE button
8
9
GB
Connecting the speakers
Before moving or installing the product, be sure to turn off the power and disconnect the power cord.
ACTIVE SUBWOOFER
(BUILT-IN POWER AMPLIFIER)
PS-AW720S
FRONT (R)
PS-AF720S
SURROUND
BACK (R)
PS-AB720S
SURROUND
BACK (R)
PS-AB720S
SR
SBL
Surround Speakers
• Place AV Receiver on a dedicated stand or rack.
• Place these speakers behind your listening position.
• If there isn't enough room, place these speakers so they
face each other.
• Place them about 60 to 90cm (2 to 3feet) above your
ears, facing slightly downward.
❈ Unlike the front and center speakers, the surround
speakers are used to handle mainly sound effects and
sound will not come from them all the time.
• Place these speakers in front of your listening
position, facing inwards (about 45°) toward you.
• Place the speakers so that their tweeters will be at the
same height as your ears.
• Align the front face of the front speakers with the front
face of the center speaker or place them slightly in
front of the center speaker.
Center speaker
• It is best to install it at the same height as the front speakers.
• You can also install it directly over or under the TV.
Subwoofer
• The position of the subwoofer is not so critical.
Place it anywhere you like.
MAIN UNIT
AV-R720
SYSTEM MODEL NAME : HT-AS720S
SBR
Position of AV Receiver
Front Speakers
Surround Back Speakers SBL SBR
CENTER
PS-AC720S
MAIN UNIT
FRONT SPEAKER
CENTER SPEAKER
SURROUND SPEAKER
SURROUND BACK SPEAKER
ACTIVE SUBWOOFER
AV-R720
PS-AF720S
PS-AC720S
PS-AR720S
PS-AB720S
PS-AW720S
√ CONNECTING SPEAKER WIRE
1. Loosen the knob by turning counterclockwise.
2. Insert the bare part of the wire into the hole in the side of each terminal.
3. Tighten the knob by turning clockwise to secure the wire.
• If you are using two rear center speakers, place them
facing forward from behind the listening position.
• Place the surround back speaker about 70 cm to 1 m
(2.3~3.3feet) above surround speakers, facing slightly
downwards.
• When you attach the speakers to a wall, make sure to
fasten them tightly so they do not fall off.
Subwoofer function
Active subwoofer with integrated 150W amplifier provides rich bass sound.
10
SURROUND (L)
PS-AR720S
CONNECTIONS
SL
FRONT (L) SURROUND (R)
PS-AF720S
PS-AR720S
1
Connect the SW OUT terminal of the amplifier (AV-R720) to the INPUT
terminal of the subwoofer speaker.
2
Press the POWER button on the rear side of the subwoofer to turn
the power on.
3
Using the subwoofer’s VOLUME control, you can set the desired bass level
(See page 28 "Setting Speaker Level" to set the subwoofer level in the menu).
√ Connecting the Speakers
1. Press down the terminal tab on the back of the speaker.
2. Insert the black wire into the black terminal (–) and the red wire
into the red (+) terminal, and then release the tab.
3. Connect the connecting plugs to the back of the AV receiver.
• Make sure the colors of the speaker terminals match the colors
of the connecting plugs.
Caution
• Keep the subwoofer speaker out of reach of children to
prevent them from inserting their hands or objects
into the duct (hole).
1
2
Black
Red
• Never touch speaker terminals while the power is on.
Doing so could result in electric shock.
• Make sure the polarities (+ and -) are correct.
• This system is capable of reproducing 6.1/7.1 channel
sound, however only 5.1 speakers are supplied.
11
GB
Connecting external devices
Connecting video devices
Before moving or installing the product, be sure to turn off the power and disconnect the power cord.
SAT(Cable/Satellite/Settop Box)
DVD or Blu-RAY Player
CONNECTIONS
• If the external component has only one audio output
jack, connect it to either the right or left audio input
jack of the main unit.
• Connect the audio cable's red plug to the red jack
and white cable to the white jack.
or
or
TV
• Disconnect the power plug from the outlet if you will not use this unit for a long period of time.
• Even though the Digital Audio inputs are labelled DVD, SAT and CD, you can connect your DVD/SAT/CD player to
either the OPTICAL or COAXIAL digital audio input (as long as it matches the Digital audio output on your player).
TV
VCR
12
13
GB
Connecting external devices
(cont’d)
Connecting audio/7.1 channel devices
Connecting external devices via HDMI
Before moving or installing the product, be sure to turn off the power and disconnect the power cord.
By connecting through the HDMI(High-Definition Multimedia Interface) interface, you can play back digital video and audio
without conversion to analog.
DVD or Blu-RAY Player
SAT(Cable/Satellite/Set-top box)
CONNECTIONS
CD Player
• Connect it if you
want to use Anynet+.
• Audio from SACD discs will not be played. To play a
DVD disk whose copyright is protected by CPPM, use a
player supporting CPPM.
• The quality of the audio output through the HDMI jack
(sampling frequency and bit rate) may be limited by the
performance of the connected device.
• Since HDMI connection supports both video and audio,
you don’t have to connect an additional audio cable.
TV
High-bandwidth Digital Content Protection System (HDCP) support
To play digital contents through the HDMI connection, both of the connected external device and TV must support High-bandwidth Digital Content
Protection System (HDCP). This product supports HDCP.
TV
DVD/Blu-RAY or 7.1 channel player
COMPATIBILITY WITH A TV SUPPORTING HDMI
A TV with an HDMI jack.
Video/Audio
A TV with a DVI-D jack (TV supporting HDCP)
Video
A TV with a DVI-D jack (TV not supporting HDCP)
-
• If you use an HDMI cable to connect a Samsung TV to the DVD Player, you can operate the AV receiver using the TV’s remote
control. This function is available only in connection with Samsung TV and DVD player supporting Anynet +(HDMI-CEC).
logo. If your TV has an
logo, then it supports the Anynet+ function.
• Please check the
14
15
Anynet+
GB
Connecting external devices
(Cont'd)
Using Anynet+(HDMI-CEC)
Connecting AUX components
1 Connect the AV receiver to a Samsung TV with an HDMI cable. (See page 15)
the Anynet+ function on your TV. (See the TV instruction manual for more information.)
2 Set
•
You can connect external devices you use (camcorder, game console, mobile equipment,etc.) to the front of this unit for
convenience.
You can operate the AV receiver by using the TV remote control.
(Available TV button : VOLUME
,
button.)
CONNECTIONS
If you select TV
Set the Anynet+(HDMI-CEC) function to <On> on your TV.
• Receiver : On : You can listen to audio through the AV Receiver.
• Receiver : Off : You can listen to audio through the TV.
MOVE
MOVE
ENTER
ENTER
EXIT
EXIT
If you select the DVD Player
Camcorder
Select THEATER to connector and set the option of each items below.
• View TV : If Anynet+(HDMI-CEC) set to on and you select View TV, the AV receiver will
automatically switch to SAT OPTIC2(DIGITAL IN).
• Receiver : On : You can listen to audio through the AV receiver.
• Receiver : Off : You can listen to audio through the TV.
MOVE
ENTER
EXIT
To turn off Anynet+
1 Press SETUP/MENU button, and then press the ENTER button.
• “SETUP MODE” appears on the display and goes into Setup Mode.
2 Press œ √ button to select the “ANYNET+ MODE”, and then press the ENTER
button.
3 Press the …† button to set ANYNET+ to OFF.
- If you are using Anynet+, set ANYNET+ to ON and if not, set it to OFF.
Connecting the FM antenna
To exit setup mode
• Wait for about 5 seconds or press SETUP button.
“SETUP OFF” appears on the display and Setup Mode is exited.
• When selecting View TV, you must have a digital optical cable connected
from the TV to the AV receiver to listen to the TV sound through the AV
receiver.
Caution
• When you are making Anynet+ connection, do not connect more than two AV receivers
(Anynet+ installed). Otherwise, it can cause a malfunction.
With Anynet+
You can operate this unit, power on your TV, or watch a movie by pressing the Play button on
your Samsung TV's remote control.
16
FM antenna (supplied)
FM antenna connection
1. Connect the FM antenna supplied to the FM 75Ω COAXIAL terminal as a temporary measure.
2. Slowly move the antenna wire around until you find a location where reception is good, then fasten it to a
wall or other rigid surface.
17
Before using the AV receiver
GB
Selecting digital/analogue Input
You can listen to sound in 2 channel analog , Dolby Digital or DTS using this unit.
Turning On/Off
Connect the power plug to the outlet.
Press the POWER button of the remote control.
• This unit will be turned on or set to Standby mode.
Remote control functions
You can operate your AMP (this AV receiver), TV, DVD and VCR with this
remote control.
See pages 43-46 for more details.
Method 1
Press the FUNCTION button.
• Each time you press this button, FM ➝ 7. 1 MULTI CH ➝ CD ➝ DVD
MAIN UNIT
Press the INPUT MODE button.
Press the INPUT MODE button.
• Each time you press this button, input mode changes
• Each time the button is pressed, input mode changes
OPERATION
To select a function
REMOTE CONTROL
as follows:
as follows:
For DVD/SAT function
➝ SAT ➝ VCR ➝ AUX will be selected in turn.
Method 2
Press CD, VCR, DVD, 7.1CH, SAT, AUX or TUNER button.
√
√
√
√
or
• You can directly select the desired function.
For CD function
√
• You can change the digital input setting for DVD, SAT and CD functions in the “DIGITAL IN” setup.
(See page 23)
• You can enjoy Dolby Digital or DTS if you connect the digital audio output jack of an external audio
component to the optical or coaxial digital audio input jack on the main unit.
18
19
GB
Setting the speaker mode
Signal outputs and frequency response from the speaker will be adjusted according to your speaker configuration
and whether certain speakers are used or not.
√
REMOTE CONTROL
1 Press SETUP/MENU button, and then press ENTER button.
• “SETUP MODE” appears on the display and goes into Setup Mode.
button to select the “SPK SETUP”, and then
2 Press
press ENTER button.
MAIN UNIT
SETUP button, and then press ENTER ( ) button.
1 Press
“SETUP MODE” appears on the display and goes into Setup Mode.
button to select the speaker you want.
3 Press
Each time you press this button, FRONT ➝ CEN ➝ SURR ➝ S.BACK ➝
•
•
2 Press
SUB ➝ CROVR will be selected in turn.
Press …† button to set the mode (LARGE, SMALL etc.)
4 for
the selected speaker.
3 Press
SUB ➝ CROVR will be selected in turn.
To exit setup mode
4 Press …† button to set the mode (LARGE, SMALL etc.)
• Wait for about 5 seconds or press SETUP/MENU button.
for the selected speaker.
“SETUP OFF” appears on the display and Setup Mode is exited.
5 Repeat steps 3-4 to set the mode for each speaker.
Using the SPK SELECT button
1 Press SPK SELECT button to select the speaker you want.
To exit setup mode
• Each time you press this button, FRONT ➝ CEN ➝ SURR ➝ S.BACK ➝
• Wait for about 5 seconds or press SETUP button.
SUB ➝ CROVR will be selected in turn.
“SETUP OFF” appears on the display and Setup Mode is exited.
2 Press …† button to set the mode (LARGE, SMALL etc.)
for the selected speaker.
3 Repeat steps 1-2 to set the mode for each speaker.
Press SUBWOOFER button on the remote.
• Each time you press this button, SUB : YES, SUB : NO will be selected in turn.
• If FRONT is set to LARGE, you can select YES or NO for SUB.
• If FRONT is set to SMALL, SUB is automatically set to YES.
NO cannot be selected.
20
button to select the speaker you want.
• Each time you press this button, FRONT ➝ CEN ➝ SURR ➝ S.BACK ➝
5 Repeat steps 3-4 to set the mode for each speaker.
To turn the SUBWOOFER on or off.
OPERATION
button to select the “SPK SETUP”, and then
press ENTER ( ) button.
Setting the Speaker
SPEAKER
FRONT(Front)
CEN(Centre)
SURR(Surround)
S.BACK (Surround Back)
SUB(Subwoofer)
CROVR
(Crossover Frequency)
Possible Settings
LARGE,SMALL
LARGE,SMALL,NONE
LARGE,SMALL,NONE
LARGE,SMALL,NONE
YES,NO
60,80,100,120,
150,180,200(Hz)
Default Setting
SMALL
SMALL
SMALL
SMALL
YES
150Hz
• LARGE : Select when using large speakers. You can listen to full
range sound.
• SMALL : Select this when using small speakers
• NONE : Select when no speaker is used
• YES (subwoofer) : Select when using the subwoofer speaker.
• NO (subwoofer) : Select when not using the subwoofer speaker.
• CROVR : Select the crossover frequency for the best bass response
in your room.
21
Setting the speaker listening distance
Setting digital input
If the speakers cannot be placed at equal distances from the listening position, you can adjust the
delay time of the audio signals from the centre and surround speakers.
You can set the digital input for a DVD/SAT/CD player to either OPTICAL or COAXIAL to match the
connections you've made .
√
GB
√
SETUP/MENU button, and then press ENTER button.
1 Press
“SETUP MODE” appears on the display and goes into Setup Mode.
•
1 Press SETUP/MENU button, and then press ENTER
button.
• “SETUP MODE” appears on the display and goes into Setup Mode.
2 Press
button to select the “DIST SETUP”, and then
press ENTER button.
button to select the speaker you want.
3 Press
Each time you press this button, F.L ➝ CEN ➝ F.R ➝ S.R ➝ SBR ➝ SBL ➝
•
S.L ➝ S.W will be selected in turn.
• For F.L, CEN, F.R, S.W, S.R, SBR, SBL, S.L Speaker, you can set the distance
from the speaker to listening position between 0.3~9.0m in intervals of
0.3m.
button to select the “DIGITAL IN”, and then
press ENTER button.
3 Press
button to select the the CD, DVD or SAT
function.
• Each time you press this button, CD ➝ DVD ➝ SAT will be selected in turn.
OPERATION
4 Press …† button to set the speaker distance.
2 Press
…† button to set the digital input.
4 Press
Each time you press this button, COAXIAL ➝ OPTICAL2 ➝ OPTICAL1
•
will be selected in turn.
To exit setup mode
• Wait for about 5 seconds or press SETUP/MENU button.
“SETUP OFF” appears on the display and Setup Mode is exited.
To exit setup mode
• Wait for about 5 seconds or press SETUP/MENU button.
“SETUP OFF” appears on the display and Setup Mode is exited.
Setting Speaker Distance
Set the distance from the speaker to listening position in intervals of 0.3m.
• F.L (front left) : 0.3m ~ 9m
• F.R (front right) : 0.3m ~ 9m
• SBR (surround back right) : 0.3m ~ 9m
• S.L (surround left) : 0.3m ~ 9m
• CEN (centre) : 0.3m ~ 9m
• S.R (surround right) : 0.3m ~ 9m
• SBL (surround back left) : 0.3m ~ 9m
• SW (subwoofer) : 0.3m ~ 9m
• If the listening position is beyond the range of the speaker distance setup,
set the speaker distance to the maximum.
• The distance range of the overall speaker system is determined based on
the F.L(front left) speaker distance from the listening position.
• Based on the max delay channel, the distance of the front speaker is
1.5m(5ms) and the surround speaker can be set up to 4.5m(15ms).
22
• You can select only one digital input for each function.
Example) If you have selected COAXIAL for the CD function,
you cannot select COAXIAL for the DVD or SAT function.
Function
DVD
SAT
CD
Digital input
OPTICAL1
OPTICAL2
COAXIAL
23
Setting HDMI AUDIO
Setting DRC (Dynamic Range Compression)
You can set HDMI audio settings.
You can use this function to enjoy Dolby Digital sound when watching movies at low volume at night.
DRC compresses the audio to make the loudest sounds quieter and the quietest sounds louder.
√
Before using!
• Press the INPUT MODE button to select HDMI1 or HDMI2. (see page 19)
• If you select Digital (Optical, Coaxial) or Analogue, the HDMI audio setting will be
deactivated.
1 Press SETUP/MENU button, and then press ENTER
button.
• “SETUP MODE” appears on the display and goes into Setup Mode.
2 Press
• “HDMI : AVR” appears on the display.
…† button to set the HDMI audio.
3 Press
Each time you press this button, HDMI : AVR ➝ HDMI : TV will be selected
•
in turn.
To exit setup mode
• Wait for about 5 seconds or press SETUP/MENU button.
“SETUP OFF” appears on the display and Setup Mode is exited.
√
1 Press SETUP/MENU button, and then press ENTER
button.
• “SETUP MODE” appears on the display and goes into Setup Mode.
2 Press
button to select the “DRC SETUP”, and
then press ENTER button.
• “DRC:STD” appears on the display.
…† button to set the DRC.
3 Press
Each time you press this button, DRC : STD ➝ DRC : MAX ➝ DRC : MIN
•
OPERATION
button to select the “HDMI AUDIO”, and then
press ENTER button.
GB
will be selected in turn.
To exit setup mode
• Wait for about 5 seconds or press SETUP/MENU button.
“SETUP OFF” appears on the display and Setup Mode is exited.
Using the DRC button
Press DRC button.
• Each time you press this button, DRC : STD ➝ DRC : MAX ➝ DRC : MIN will be
selected in turn.
Setting HDMI AUDIO
• AVR : Audio is played on this product.
• TV : Audio is played on a TV connected to the HDMI OUT jack and no audio is
played on this product.
Setting DRC
• STD : Sets DRC effect to standard.
• MAX : Sets DRC effect to maximum.
• MIN : Sets DRC effect to minimum.
• This function is available when both video input and outputs HDMI.
• HDMI AUDIO setting is available only when the HDMI output is
connected to a TV.
• If you do not hear sound from the TV, should change the HDMI audio
output setting for your DVD PLAYER or SAT to PCM.
24
25
GB
Test tone
Use the test tone check the speaker connection status or level.
To automatically output test tone
To Manually Output Test Tone
√
1 Press SETUP/MENU button, and then press ENTER
button.
• “SETUP MODE” appears on the display and the unit goes into Setup Mode.
2
Press
button to select the “TEST-T AUTO”,
and then press ENTER button.
• Test signal will be automatically output as follows; F.L ➝ CEN ➝ F.R ➝
To stop test tone
• Press SETUP/MENU button once time.
“SETUP OFF” appears on the display and test tone stops.
SETUP/MENU button, and then press ENTER button.
1 Press
“SETUP MODE” appears on the display and goes into Setup Mode.
•
2 Press ➛❿ button to select the “TEST-T MANU”, and then
press ENTER button.
➛❿ button to select the speaker you want..
3 Press
Each time you press ➛❿button, F.L ➝ CEN ➝ F.R ➝ S.R ➝ SBR ➝ SBL
•
OPERATION
S.R ➝ SBR ➝ SBL ➝ S.L ➝ S.W .
• During test signal output, press …† button to adjust the individual speaker
output level from -10 to +10 dB by 1 step.
√
➝ S.L ➝ S.W will be selected in turn.
4 Press …† button to set the test tone as you want.
• You can adjust the speaker output level from -10 to +10dB by 1 step.
• The sound gets quieter at -10dB and louder at +10dB.
To stop test tone
• Press SETUP/MENU button once time.
Using the Test Tone button
“SETUP OFF” appears on the display and test tone stops.
Press TEST TONE button.
• Test signal will be automatically output as follows; F.L ➝ CEN ➝ F.R ➝ S.R ➝
SBR ➝ SBL ➝ S.L ➝ S.W.
• During test tone output, press …† button to adjust the speaker output level from
-10 to +10 dB by 1 step.
Test Tone Output
• F.L (front left) : -10 ~ +10dB
• CEN (centre) : -10 ~ +10dB
• F.R (front right) : -10 ~ +10dB
• S.R (surround right) : -10 ~ +10dB
• SBR (surround back right) : -10 ~ +10dB
• SBL (surround back left) : -10 ~ +10dB
• S.L (surround left) : -10 ~ +10dB
• S.W (subwoofer) : -10 ~ +10dB
26
27
Setting speaker level
Dolby Pro Logic llx mode
You can set the balance and level of speakers.
This mode provides 7.1 channel sound from 2 channel sources.
√
GB
REMOTE CONTROL
Press
MODE button.
• Each time you press this button, CINEMA ➝ MATRIX ➝ GAME
1 Press SETUP/MENU button, and then press ENTER
➝ PL ➝ MUSIC will be selected in turn.
button.
• “SETUP MODE” appears on the display and goes into Setup Mode.
2 Press
button to select the “LEVEL SETUP”, and then
press ENTER button.
3 Press
button to select the speaker you want.
button, F.L ➝ CEN ➝ F.R ➝ S.R ➝ SBR ➝ SBL
➝ S.L ➝ S.W will be selected in turn.
• Each time you press
• You can adjust it from -10 to +10dB by 1 step.
• The sound gets quieter at -10dB and louder at +10dB.
To exit setup mode
• Wait for about 5 seconds or press SETUP/MENU button.
“SETUP OFF” appears on the display and Setup Mode is exited.
Using the SPK LEVEL button
SURROUND button to select “DPLIIx MODE”.
1 Press
Each time you press this button, DPLIIx ➝ NEO:6 ➝ SFE ➝ STEREO
OPERATION
4 Press …† button to set the speaker mode.
MAIN UNIT
•
will be selected in turn.
2 Press SELECT(
,
) button.
) button, CINEMA ➝ MATRIX ➝
GAME ➝ PL ➝ MUSIC will be selected in turn.
• Each time you press SELECT (
) button, MUSIC ➝ PL ➝ GAME ➝
MATRIX ➝ CINEMA will be selected in turn.
• Each time you press SELECT (
To exit setup mode
• Wait for about 5 seconds.
1 Press SPK LEVEL button to select the speaker you want.
• Each time you press this button, F.L ➝ CEN ➝ F.R ➝ S.R ➝ SBR ➝ SBL ➝ S.L
➝ S.W ➝ SPK LVL OFF will be selected in turn.
2 Press …† button to set the speaker level you want.
• You can adjust it from -10 to +10dB by 1 step.
• The sound gets quieter at -10dB and louder at +10dB.
Dolby Pro Logic llx mode
• MUSIC : Provides 7.1 channel surround sound for digital, analog or existing stereo
sources such as CD, TAPE, FM, TV and stereo VCR.
• CINEMA : Adds realism to the movie soundtrack.
• MATRIX : You will hear 7.1 channel surround sound.
• GAME : Enhances the excitement of the game's sound.
• PL : You will experience a surround effect with just the front left and right speakers.
Setting Speaker Level
• F.L (front left) : -10 ~ +10dB
• CEN (centre) : -10 ~ +10dB
• F.R (front right) : -10 ~ +10dB
• S.R (surround right) : -10 ~ +10dB
• SBR (surround back right) : -10 ~ +10dB
• SBL (surround back left) : -10 ~ +10dB
• S.L (surround left) : -10 ~ +10dB
• S.W (subwoofer) : -10 ~ +10dB
28
• You cannot use Dolby Pro Logic llx mode for multi channel signals such as
Dolby Digital and DTS.
• Pro Logic works only for PCM audio signals with sampling frequencies of
32KHz, 44KHz or 48KHz.
• Sound will not be output from the surround back speaker if the PCM audio signal
is mono.
29
Setting Dolby Pro Logic llx effect
Setting NEO:6 mode
This function works only in Dolby PRO LOGIC IIx MUSIC Mode.
You can play back 2 channel sound over 6.1 channels when enjoying music or a movie.
Press SETUP/MENU button, and then press ENTER
1 button.
• “SETUP MODE” appears on the display and goes into Setup Mode.
2
GB
REMOTE CONTROL
Press NEO:6 MODE button.
• Each time you press this button, MUSIC ➝ CINEMA will be selected in turn.
MAIN UNIT
Press
button to select the “
and then press ENTER button.
MODE”,
SURROUND button briefly to select “NEO:6” mode.
1 Press
Each time you press this button, DPLIIx ➝ NEO:6 ➝ SFE ➝ STEREO will
•
be selected in turn.
button.
3 Press
Each time you press this button,
•
C-WIDTH ➝ DIMENSION ➝
PANORAMA will be selected in turn.
want.
• Wait for about 5 seconds or press SETUP/MENU button.
“SETUP OFF” appears on the display and Setup Mode is exited.
1 Press
2 Press
To set the height of the center sound image
If your TV (or screen) is installed high on a wall, you can raise the center
sound image of the front and center speakers to compensate.
1 Press SETUP/MENU button, and then press ENTER button.
“SETUP MODE” appears on the display and goes into Setup Mode.
2 Press button to select the “NEO:6 MODE”, and then
•
To exit setup mode
Using the
•
EFFECT button
MODE button to select ‘MUSIC’ Mode.
EFFECT button.
• Each time you press this button, C-WIDTH ➝ DIMENSION ➝ PANORAMA
will be selected in turn.
3 Press …† button to select Dolby Pro Logic IIx effect you want.
• C-WIDTH : You can set from 0 to 7.
• DIMENSION : You can set from -7 to +7.
• PANORAMA : You can set it ON or OFF.
Dolby Pro Logic llx effect
• C-WIDTH : This sets the width of the centre image. The higher the setting, the
less sound comes from the centre speaker.
• DIMENSION : Incrementally adjusts the sound field (DSP)from the front or surround.
• PANORAMA : This mode extends the front stereo image to include the surround
speakers for an exciting "wraparound" effect with side wall imaging.
press ENTER button.
• “CEN -- IMG : 2” appears on the display.
3 Press …† button to set the sound image you want.
• You can set the sound image from 0 to 5.
• This parameter adjusts the height of the center image through the front and
center speakers. “0” is the lowest while “5” is the highest.
To exit setup mode
• Wait for about 5 seconds or press SETUP/MENU button.
“SETUP OFF” appears on the display and Setup Mode is exited.
NEO : 6 Mode
This mode decodes 2 channel signals to a high precision digital matrix decoder.
for 6.1 channel sound.
• MUSIC : NEO:6 MUSIC mode is optimized for music playback
• CINEMA : NEO:6 CINEMA mode is optimized for movie playback.
• NEO:6 mode cannot be used with DTS and Dolby Digital multi channel signals.
• Pro Logic works only for PCM audio signals with sampling frequencies of
32KHz, 44KHz or 48KHz.
30
31
OPERATION
Press …† button to set the
4 Dolby
Pro Logic llx effect you
SELECT( , ) button.
2 Press
Each time you press this button, MUSIC ➝ CINEMA will be selected in turn.
Setting EX/ES mode
Setting Tone Control
When surround back speakers are connected, you can listen to 6.1 or 7.1 multi-channel sound
using the built-in Dolby Digital Surround EX or DTS ES decoder. This function works when a Dolby Digital or
DTS source (such as a DVD player) is input, and does not work with L.PCM and Dolby Digital 2 channel sources.
This function allows setting up the tone quality of the front speaker.
SETUP/MENU button, and then press ENTER button.
1 Press
“SETUP MODE” appears on the display and goes into Setup Mode.
2 Press button to select the “EX/ES SETUP”, and then
GB
•
press ENTER button.
1 Press SETUP/MENU button, and then press the ENTER button.
“SETUP MODE” appears on the display and goes into Setup Mode.
2 Press button to select the “TONE CONTROL”, and
•
• “EX/ES : AUTO” appears on the display.
…† button to set
3 Press
the EX/ES you want.
• Each time you press this button,
EX/ES : AUTO ➝ EX/ES : ON ➝
EX/ES : OFF will be selected in turn.
then press the ENTER button.
3 Press
button.
• Each time you press this button, BASS ➝ TREBLE ➝ TONE : OFF will be
selected in turn.
• If it is set to TONE: OFF, the Tone Control function will be disabled.
To exit setup mode
• Wait for about 5 seconds or press SETUP/MENU button.
Using the EX/ES button
• You can adjust it from -6 to +6dB by 1 step.
• The sound gets smaller at -6dB and louder at +6dB.
OPERATION
“SETUP OFF” appears on the display and Setup Mode is exited.
4 Press …† button to set the tone control you want.
To exit setup mode
• Wait for about 5 seconds or press SETUP/MENU button.
Press EX/ES button.
• Each time you press this button, EX/ES : AUTO ➝ EX/ES : ON ➝ EX/ES : OFF
“SETUP OFF” appears on the display and Setup Mode is exited.
will be selected in turn.
• The EX/ES button on the remote control is enabled only if the input source is of
Dolby Digital or DTS.
EX/ES Mode
• AUTO : If the unit receives an audio signal that it can recognize, it will select an
optimal decoder for playback in 6.1/7.1 channel.
If the amplifier does not recognize the audio signal, it will not play in
6.1/7.1 channel automatically.
• ON : Dolby Digital or DTS signal will be played in 6.1 / 7.1 channel using Dolby
Digital Surround EX / DTS ES decoder.
• OFF : Dolby Digital Surround EX / DTS ES decoder will not be used for playback.
Dolby Digital - EX
Movie soundtracks encoded with Dolby Digital EX will play audio over
the surround back channels also.
• You cannot use Dolby Digital-EX in the system without
Surround Back speakers connected.
• EX/ES Mode must be set to On when playing back discs
DTS-ES (Discrete 6.1, Matrix 6.1)
A surround back channel is added to the DTS 5.1 channel
system, improving the sense of sound directionality and space.
A built-in DTS-ES decoder has been equipped with this system
that supports discs encoded with DTS-ES Direct and DTS-ES
Matrix.
• Tone Control function is available only in the Stereo mode.
• You cannot use DTS-ES without surround back
speakers connected.
encoded with 6.1 channel Dolby Digital-EX.
• Some discs encoded with Dolby Digital-EX do not contain
an identification signal. In this case, set EX/ES to ON.
32
33
GB
SFE mode
Stereo mode
The SFE (Sound Field Effect) function uses 7 different DSP sound field effects to digitally simulate actual music
environments such as concert halls or cinemas.
You can select this mode when listening to sound through the front left and right speakers and subwoofer.
REMOTE CONTROL
REMOTE CONTROL
Press SFE MODE button.
Press STEREO button.
• Each time you press this button, HALL ➝ THEATER ➝ ARENA ➝ CLUB ➝
• “STEREO” appears in the display and
DOME ➝ STADIUM ➝ CHURCH will be selected in turn.
Stereo Mode is selected.
MAIN UNIT
Press SURROUND button to select ‘STEREO’.
• Each time you press this button, DPLIIx ➝ NEO:6 ➝ SFE ➝ STEREO will be
selected in turn.
• If you press the STEREO button on the player, it will switch to STEREO mode.
To exit setup mode
• Wait for about 5 seconds.
Surround Mode and Input Signal Chart
SURROUND button to select ‘SFE’ Mode.
1 Press
Each time you press this button, DPLIIx ➝ NEO:6 ➝ SFE ➝ STEREO
•
will be selected in turn.
SELECT( , ) button.
2 Press
Each time you press Select (
) button, HALL
,
•
THEATER ARENA CLUB DOME STADIUM CHURCH will be selected
in turn.
To exit setup mode
OPERATION
MAIN UNIT
o = active, – = inactive
Surround
Mode
DOLBY
(MUSIC,
CINEMA,
MATRIX,
GAME,
PRO LOGIC)
NEO:6
(MUSIC,
CINEMA)
• Wait for about 5 seconds.
SFE
EX/ES
STEREO
Input Signal
Decoding
Output Channel
SL SBL SubW
L/R C SR
SBR
Display Information
Display Signal Format
Channel Status
Dolby D Surr. EX
Dolby Digital 5.1
O
O
O
O
O
DIGITAL
L, C, R, SL, SR, SBL, SBR, SW
Dolby D (5.1ch)
Dolby Digital 5.1
O
O
O
–
O
DIGITAL
L, C, R, SL, SR, SW
Dolby D (2ch)
Pro Logic II x
O
O
O
O
O
DIGITAL
L, C, R, SL, SR, SBL, SBR, SW
Dolby D (2ch Surr)
Pro Logic II x
O
O
O
O
O
DIGITAL
L.PCM (Audio)
Pro Logic II x
O
O
O
O
O
L.PCM
L, C, R, SL, SR, SBL, SBR, SW
Analog
Pro Logic II x
O
O
O
O
O
ANALOGUE
L, C, R, SL, SR, SBL, SBR, SW
L.PCM (Audio)
Neo:6
O
O
O
O
O
L.PCM
L, C, R, SL, SR, SBL, SBR, SW
Analog
Neo:6
O
O
O
O
O
ANALOGUE
L, C, R, SL, SR, SBL, SBR, SW
Dolby D (2ch)
Neo:6
O
O
O
O
O
DIGITAL
L, C, R, SL, SR, SBL, SBR, SW
Dolby D (2ch Surr)
Neo:6
O
O
O
O
O
DIGITAL
L, C, R, SL, SR, SBL, SBR, SW
Dolby D (2ch)
DD+SFE
O
O
O
–
O
DIGITAL
L, C, R, SL, SR, SW
Dolby D (2ch Surr)
DD+SFE
O
O
O
–
O
L.PCM (Audio)
SFE
O
O
O
–
O
L.PCM
L, C, R, SL, SR, SW
Analog
SFE
O
O
O
–
O
ANALOGUE
L, C, R, SL, SR, SW
Dolby D Surr. EX
Dolby Digital EX
O
O
O
O
O
DIGITAL
Dolby D (5.1ch)
Dolby Digital EX
O
O
O
O
O
DIGITAL
DTS-ES
DTS-ES
O
O
O
O
O
dts, ES
L, C, R, SL, SR, SBL, SBR, SW
DTS (5.1ch)
DTS-ES
O
O
O
O
O
dts
L, C, R, SL, SR, SBL, SBR, SW
Dolby D (2ch)
Stereo
O
–
–
–
O
DIGITAL
Dolby D (2ch Surr)
Stereo
O
–
–
–
O
DIGITAL
L.PCM (Audio)
Stereo
O
–
–
–
O
L.PCM
L.PCM 96KHz
Stereo
O
–
–
–
O
L.PCM
L, R, SW
Analog
Stereo
O
–
–
–
O
ANALOGUE
L, R, SW
DIGITAL
L, C, R, SL, SR, SBL, SBR, SW
L, C, R, SL, SR, SW
L, C, R, SL, SR, SBL, SBR, SW
L, C, R, SL, SR, SBL, SBR, SW
L, R, SW
L, R, SW
L, R, SW
L/R : front speaker (left/right) C : centre speaker SL/SR : surround speaker (left/right) SBL/SBR : surround back speaker (left/right)
SW : subwoofer
34
• Channel status displays are dependent on the speaker configuration.
• SFE mode works with 2-ch signals.
35
Listening to radio
Presetting radio Stations
You can listen to the chosen band (FM) by using either automatic or manual tuning.
You can preset up to 30 FM stations.
REMOTE CONTROL
E.g.: Setting station FM 89.10 in preset 2 .
1 Press TUNER button.
2 Selected frequency.
1 Press TUNER button.
TUNING MODE button to
2 Press
select MANUAL and then press
• Automatic tuning 1
:
TUNING/CH(
select 89.10.
1) Press TUNING MODE button to select PRESET.
2) Press TUNING/CH ( , ) button to select the preset frequency.
• Automatic tuning 2
:
automatically and manually.
3 Press TUNER MEMORY button.
:
1) Press TUNING MODE button to select MANUAL.
2) Press TUNING/CH ( , ) button briefly to increase or decrease the
frequency step by step.
• Tuner number will blink on the display.
4 Press TUNING/CH(
5 Press TUNER MEMORY button.
• Tuner number will disappear and station 89.10
will be saved in preset 2.
RADIO OPERATION
:
6 To preset other stations, repeat
1) Press TUNING MODE button to select PRESET.
2) Press TUNING/CH ( , ) button to select the preset frequency.
steps 2 to 5.
:
1) Press TUNING MODE button to select MANUAL
2) Press and hold TUNING/CH ( , ) button to automatically tune in frequency.
• Manual tuning
) button
• You can select from presets 1 to 30.
1 Press FUNCTION button to select FM.
2 Select the frequency.
• Automatic tuning 2
,
to select preset 2.
MAIN UNIT
• Automatic tuning 1
) button to
,
• Refer to step 2, page 36, to tune in
1) Press TUNING MODE button to select MANUAL
2) Press and hold TUNING/CH ( , ) button to automatically tune in frequency.
• Manual tuning
GB
To Listen to Preset Station
:
• Press TUNING MODE button of the remote control to select the PRESET
1) Press TUNING MODE button to select MANUAL.
2) Press TUNING/CH ( , ) button briefly to increase or decrease the
frequency step by step.
and press TUNING/CH (
,
) button.
To Listen to mono/stereo
Press MO/ST button on the remote.
• Each time you press this button, STEREO ➝ MONO will be selected in turn.
• If you select MONO in the area with weak reception,
it will help to reduce noise.
• This function works only with the Remote Control.
36
36
37
GB
About RDS broadcasting
Using the RDS (Radio Data System) to receive FM stations
RDS allows FM stations to send an additional signal along with their regular program signals.
For example, the stations send their station names, as well as information about what type of
program they broadcast, such as sports or music, etc.
When tuned to an FM station which provides the RDS service,the RDS indicator
lights up on the display.
• Description on RDS function
1. PTY (Program Type) : Displays the type of programme currently being broadcast
2. PS NAME (Program Service Name) : Indicates the name of broadcasting station
and is composed of 8 characters.
3. RT (Radio Text) : Decodes the text broadcast by a station (if any) and is composed
of maximum 64 characters.
4. CT (Clock Time) : Decodes the real time clock from the FM frequency.
• Some stations may not transmit PTY, RT or CT information therefore this may not be
displayed in all cases.
5. TA (Traffic Announcement) : When this symbol flashes it shows that the traffic
announcement is in progress.
• RDS may not operate correctly if the station tuned is not transmitting
RDS signal properly or if the signal strength is weak.
You can see the RDS signals the station sends on the display.
TO show the RDS signals
Press RDS DISPLAY while listening to an FM station.
Each time you press the button, the display change to show you the following information :
PS (Program Service) : While searching, "PS" appears and then the station names will be
displayed. "NO PS" appears if no signal is sent.
RT(Radio Text) : while searching, "RT" appears and then text messages the station
sends will be displayed. "NO RT" appears if no signal is sent.
Frequency : station frequency (non-RDS service)
About characters shown in the display
When the display shows PS, or RT signals, the following characters are used.
• The display window cannot differentiate upper case and lower case letters and always
uses upper case letters.
• The display window cannot show accented letters, “A,” for instance, may stands for
accented “A’s” like “À, Â, Ä, Á, Åand Ã.”
• If searching finishes at once, “PS”, and “RT” will not appear on the display.
One of the advantages of the RDS service is that you can locate a particular kind of programme from
the preset channels by specifying the PTY codes.
To search for a programme using the PTY codes
Before you start, remember...
•
•
•
•
The PTY Search is only applicable to preset
stations.
To stop searching any time during the process,
press PTY SEARCH while searching.
There is a time limit in doing the following steps.
If the setting is cancelled before you finish, start
from step 1 again.
When pressing the buttons on the primary remote
control, make sure that you have selected the FM
station using the primary remote control.
1
2
3
Press PTY SEARCH while listening to an
FM station.
Press the PTY-or PTY+until the PTY code
you want appears on the display.
• The display gives you the PTY codes described
to the right.
Press PTY SEARCH again, while the PTY
code selected in the previous step is still on
the display.
• The centre unit searches 15 preset FM
stations, stops when it finds the one you
have selected, and tunes in that station.
Display
NEWS
AFFAIRS
• Several subjects including current affairs,
documentary, discussion and analysis.
INFO
SPORT
EDUCATE
DRAMA
• Information including weights and measures,
returns and forecasts, matters interesting the
customer, medical information, etc.
• Sports
• Education
• Drama, radio serial etc.
CULTURE
• Culture : national or local culture including the
religious problem, social science, language,
theatre,etc.
SCIENCE
• Natural science and technology
VARIED
• Others: lectures, entertainment programmes
(quiz and game shows), interviews, comedy
and satirical plays etc.
POP M
• Pop music
ROCK M
• Rock music
M.O.R.M
• Current contemporary music considered to be
“easy listening.”
LIGHT M
• Light classical music - classical music and
instrumental and chorus music
CLASSICS
• Heavy classical music - orchestra music,
symphony, chamber music and opera
OTHER M
• Other music - jazz, R&B country music
WEATHER
• Weather
FINANCE
• Finance
CHILDREN
• Children’s programmes
SOCIAL A
• Social affairs
RELIGION
• Religion
PHONE IN
• Phone in
TRAVEL
• Travel
LEISURE
• Leisure
JAZZ
• Jazz music
COUNTRY
• Country music
NATION M
• National music
OLDIES
• Oldies music
FOLK M
• Folk music
DOCUMENT
38
Program Type
• News including an announced opinion and
report
RADIO OPERATION
What information can RDS signals provide?
PTY (Program Type) indication and PTY-SEARCH function
• Documentary
39
GB
Convenient functions
Sleep timer function
Reset function
You can set the time that this unit will shut itself off.
Press the SLEEP button.
• SLEEP : OFF ➝ 15 ➝ 30 ➝ 45 ➝ 60 ➝ 90 ➝ 120 M (MIN) will be selected in turn.
REMOTE CONTROL
1 Press the MUTE button.
MUTE appears on the display.
2 Press “0” button five times and then
•
To check sleep timer
Press SLEEP button.
• The remaining time before this unit will shut itself off is shown on the display.
• Pressing the button again changes the sleep time from what you set previously.
To cancel sleep timer
press ENTER button.
• “INITIAL : NO” appears on the display.
…† buttons to select “YES”.
3 Press
The unit will turn off after 5 seconds.
•
• Press SLEEP button until “SLEEP : OFF” appears on the display.
MAIN UNIT
Mute function
This function is useful when answering a doorbell or telephone call.
1 Turn off the power and hold the SELECT(
) button for
longer than 5 seconds.
• POWER STANDBY indicator will flash.
Press the MUTE button.
• MUTE appears on the display.
To output sound again
Caution!
• Using the RESET function will erase all stored settings.
• Do not use this unless necessary.
Press MUTE button again.
• MUTE will disappear and sound will output.
MISCELLANEOUS
• SLEEP, Mute and the Adjust Display function can only be
operated with the remote control.
40
41
Convenient functions (cont’d)
Adjust the display
You can adjust the brightness of the display.
Press the DIMMER button.
Operating your TV with the remote control
1
Press POWER button to turn on
the TV.
2
Press TV button to set the remote to TV
mode.
3
Point the remote control toward the TV.
4
While holding down POWER button,
enter the code corresponding to your
brand of TV.
GB
• Each time you press this, the brightness changes as follows : DARK ➝ BRIGHT.
Using headphones
Use headphones (not supplied) for private listening pleasure.
Connect the headphones to the headphone jack and listen to
music.
• If there is more than one code listed for your TV in the table,
enter one at a time to determine which code works.
• If the code matches the TV's code, the TV will be turned off.
MISCELLANEOUS
5
If TV is turned on or off when you press the
power button of the remote control, the
setting is completed.
• You can use the TV POWER, VOLUME, CHANNEL, MENU and
Numeric buttons (0~9).
• Do not turn the volume up too high when you use headphones as It
may damage your hearing.
• The remote control may not work on some brands of TVs. Also, some operations
may not be possible depending on your brand of TV.
• The remote control will work with Samsung TVs by default.
42
43
Operating your TV with the remote control
GB
Operating your DVD or VCR with the remote control
(cont’d)
TV Brand Code List
Brand
Code Number
44
LUXMAN
LXI (SEARS)
MAGNAVOX
MARANTZ
MATSUI
MGA
MITSUBISHI/MGA
MTC
NEC
NIKEI
ONKING
ONWA
PANASONIC
PENNEY
PHILCO
PHILIPS
PIONEER
PORTLAND
PROTON
QUASAR
RADIO SHACK
RCA/PROSCAN
REALISTIC
SAMPO
SAMSUNG
SANYO
SCOTT
SEARS
SHARP
SIGNATURE 2000 (M.WARDS)
SONY
SOUNDESIGN
SPECTRICON
SSS
Code Number
018
019, 054, 056, 059, 060,
062, 063, 065, 071
015, 017, 018, 048, 054,
059, 060, 062, 072, 089
040, 054
054
018, 040
018, 040, 054, 059, 060,
075, 101
018
018, 019, 020, 040, 059,
060
003
003
003
006, 007, 008, 009, 054,
066, 067, 073, 074
018
003, 015, 017, 018, 048,
054, 059, 062, 069, 090
015, 017, 018, 040, 048
054, 062, 072, 112, 114,
117, 118
063, 066, 080, 091
015, 018, 059
040
006, 066, 067
017, 048, 056, 060, 061,
075
018, 059, 067, 076, 077
078, 092, 093, 094
003, 019
040
000, 015, 016, 017, 040,
043, 046, 047, 048, 049,
054, 059, 060, 098
019, 061, 065, 101, 102,
103, 104
003, 040, 060, 061
015, 018, 019
015, 057, 064, 101, 105,
106, 115
057, 058
050, 051, 052, 053, 055,
101
003, 040
001
018
Brand
SYLVANIA
SYMPHONIC
TATUNG
TECHWOOD
TEKNIKA
TMK
TOSHIBA
VIDTECH
VIDECH
WARDS
YAMAHA
YORK
YUPITERU
ZENITH
ZONDA
DONGYANG
LOWE
FINLUX
YOKO
LOEWE OPTA
PHONOLA
RADIOLA
SCHNEIDER
AKAI
GRUNDIG
BLAUPUNKT
SIEMENS
CGE
IMPERIAL
MIVAR
SABA
BANG&OLUFSEN
BRIONVEGA
FORMENTI
METZ
WEGA
RADIOMARELLI
SINGER
SINUDYNE
TELEFUNKEN
Code Number
018, 040, 048, 054, 059,
060, 062
061, 095, 096
006
018
003, 015, 018, 025
018, 040
019, 057, 063, 071, 101
107, 109, 110, 111, 113
018
059, 060, 069
015, 017, 018, 040, 048,
054, 060, 064
018
040
003
058, 079
001
003, 054
054
054, 109, 114
054
054, 114
054, 112, 114
054, 112
054
103
108, 109, 113, 119, 120,
121
108
108
113
113
113
114
114
114
114
114
114
114
114
114
116
1
Press POWER button to turn on the DVD
(VCR).
2
Press DVD button to set the remote to
DVD mode.
3
Point the remote control toward the DVD
(VCR).
4
While holding down POWER button, enter
the code corresponding to your brand of
DVD (VCR).
• If you operate VCR, press VCR button to set the remote to VCR mode.
• If there is more than one code listed for your DVD (VCR) in
the table, enter one at a time to determine which code works.
• If the code matches the DVD (VCR)'s code, the DVD (VCR)
will be turned off.
5
If DVD (VCR) is turned on or off when you
press the power button of the remote
controller, the setting is completed.
MISCELLANEOUS
056, 057, 058
001, 015
001, 002, 003, 004,005,
006, 007, 008, 009, 010,
011, 012, 013, 014
AOC
001, 018, 040, 048
BELL & HOWELL (M.WARDS) 057, 058, 081
BROCSONIC
059, 060
CANDLE
018
CETRONIC
003
CITIZEN
003, 018, 025
CINEMA
097
CLASSIC
003
CONCERTO
018
CONTEC
046
CORONADO
015
CRAIG
003, 005, 061, 082, 083,
084
CROSLEX
062
CROWN
003
CURTIS MATHES 059, 061, 063
CXC
003
DAEWOO
002, 003, 004, 015,016,
017, 018, 019, 020, 021,
022, 023, 024, 025, 026,
027, 028, 029, 030, 032,
034, 035, 036, 040, 048,
059, 090, 099, 100
DAYTRON
040
DYNASTY
003
EMERSON
003, 015, 040, 046, 059,
061, 064, 082, 083, 084,
085
FISHER
019, 065, 103
FUNAI
003
FUTURETECH
003
GENERAL ELECTRIC (GE) 006, 040, 056, 059, 066,
067, 068
HALL MARK
040
HITACHI
015, 018, 050, 059, 069
INKEL
045
JC PENNY
056, 059, 067, 086
JVC
070
KTV
059, 061, 087, 088
KEC
003, 015, 040
KMC
015
LG (GOLDSTAR)
001, 015, 016, 017, 037,
038, 039, 040, 041, 042,
043, 044, 054, 086
ADMIRAL (M.WARDS)
A MARK
ANAM
Brand
• You can use DVD (VCR) POWER, VOLUME, PLAY, PAUSE,
STOP, SKIP, MENU and Numeric button (0~9).
• The remote control may not work on some brands of DVD (VCR).
Also, some operations may not be possible depending on your brand
of DVD (VCR).
• The remote control will work with Samsung DVD (VCR) by default.
45
Operating your DVD or VCR with the remote control
GB
Before calling for service
(cont’d)
VCR Brand Code List
Brand
ADMIRAL (M.WARDS)
AWIA
AKAI
ANAM
AOC
AUDIO DYNAMIC
BELL & HOWELL (M.WARDS)
BROKSONIC
CANON
CAPEHART
CITIZEN
CRAIG
CRITERION
CURTIS MATHES
DAEWOO
DAYTRON
DBX
EMERSON
FISHER
FUNAI
GENERAL ELECTRIC (GE)
GO VIDEO
HARMAN KARDON
HITACHI
JVC
KENWOOD
LG (GOLDSTAR)
LXI (SEARS)
MAGIN
MAGNAVOX
MARANTZ
MARTA
46
043, 106
044, 045, 046
088, 089, 090
001, 002, 003, 004, 005,
033
091
019, 047, 092
048, 093
092, 094, 095
001, 033, 049, 091
011
050
050, 072, 096
051
001, 031, 032, 033, 044,
091
006, 007, 008, 009, 010,
011, 012, 013, 014, 015,
016, 017, 018, 046, 051,
091
011
019, 047, 052, 092
025, 031, 032, 044, 046,
094, 095, 097, 098, 099
009, 048, 053, 054, 055,
100
044
001, 031, 032, 033, 056,
091
059, 060, 061
019
020, 021, 049, 054, 062,
100
051
001, 033, 049, 091
001, 033
025
047, 048, 052, 062, 091,
092
001, 033, 047, 052, 063,
064, 065, 092
047, 050, 052, 092
019, 020, 021, 022, 023,
024, 025, 026, 027, 028,
029, 030, 050
020, 025, 044, 048, 050,
053, 054, 055, 062, 100
072
001, 031, 032, 033, 049,
066, 067, 091
001, 019, 033, 047, 052,
092, 110
025, 050
Brand
MEI
MEMOREX
MINOLTA
MITSUBISHI/MGA
MTC
MULTITECH
NEC
OLYMPIC
OPTIMUS
ORION
PANASONIC
PENNEY
PENTAX
PHILCO
PHILIPS
PILOT
PIONEER
PORTLAND
QUASAR
RICO
RCA/PROSCAN
REALISTIC
SAMSUNG
SANYO
SANSUI
SCOTT
SEARS
SHARP
SINGER
SIGNATURE 2000 (M.WARDS)
SHINTOM
SONY
STS
SYLVANIA
SYMPHONIC
TANDY
Code Number
001, 033
001, 025, 033, 054, 091,
100
020, 021, 062
068, 069, 070, 101, 102
072
044, 057, 069
019, 047, 052, 057, 092
049, 091
101
103
001, 004, 033, 049, 067,
091, 107
019, 020, 072
001, 020, 021, 033, 062
001, 033, 046, 049, 091,
094
001, 030, 033, 049, 050,
066, 091
025
049
011
001, 033, 049, 067, 091,
107, 108
036
001, 020, 021, 031, 032,
033, 049, 051, 062, 066,
070, 091, 104
001, 009, 025, 033,
044, 048, 054, 091,
101, 105
000, 006, 031, 032, 057,
058, 071, 072, 073, 074,
075, 076, 077, 078, 079,
080, 081
008, 009, 046, 048, 050,
054, 058, 093, 100
092
006, 051, 054, 057, 069,
070, 100, 101
020, 021, 025
043, 105, 106
096
043, 044, 054, 100, 106
096
034, 035, 036, 037, 038,
039, 040, 041, 042,082,
083, 084, 085, 086
020
001, 033, 044, 049, 066,
091
044
009
Brand
TASHIRO
TATUNG
TEAC
TECHNICS
TEKNIKA
TOSHIBA
TOTEVISION
TAEKWANG
UNITECH
VECTOR RESEARCH
VIDEO CONCEPTS
VIDEOSONIC
WARDS
YAMAHA
ZENITH
Code Number
050
047, 052, 092
044, 047, 052, 092
001, 033, 049, 091
001, 025, 033
006, 051
025, 072
087
072
019
019
072
001, 020, 031, 032, 033,
043, 050, 054, 072, 100,
105, 106, 109
019, 047,048, 052, 092,
019, 047,048, 052, 092
DVD Brand Code List
Brand
DENON
DOONOON
DMTECH
FISHER
GE
HARMAN/KARDON
JVC
KENWOOD
LG
MAGNAVOX
MITSUBISHI
ONKYO
OPTIMUS
PANASONIC
PROSCAN
PHILIPS
PIONEER
RCA
SAMSUNG
SANYO
SONY
THETA DIGITAL
TOSHIBA
YAMAHA
ZENITH
TAEGWANG
PS2
X-BOX
APEX
MARANTZ
Code Number
003, 032
019
017
002
006
012
010, 013
008
001
004
005, 016
004, 014
011
021
006
004, 023
007, 011, 022, 025
006
000, 027
002
015, 020
011
004, 018
009, 033
004, 024
026
028
029
030
031
Check
Symptom
Remedy
The unit will not turn on.
• Is the power cord plugged into the outlet?
• Connect the power plug to the outlet.
A function does not work
when the button is pressed.
• Is there static electricity in the air?
• Disconnect the power plug and connect it
again.
• Are the speakers and external
•
Sound is not produced.
•
•
•
components connected properly?
Is the Mute function on?
Is the volume set to minimum?
Is the speaker setup set incorrectly to
NONE?
Do you see the message of “NOT
SUPPORT” in playing a MPEG audio file?
Picture does not appear on a TV
when the function is selected.
• Is the external component connected
Remote controller does
not work.
• Are the batteries drained?
• Is the distance between remote
The sound from the
left/right channels is
reversed.
• Are the left/right speaker or left/right
Can't receive radio
control and main unit too great?
input/output cables connected
properly?
• Is FM antenna connected properly?
• Is SURR (surround) incorrectly set to
NONE in speaker setup?
• Is surround mode set to stereo?
centre speaker
• Refer to pages 20~21 to select LARGE,
SMALL or YES.
• The file format of MPEG is not supported.
Change the audio format of the source
device (Blu-RAY Player) to PCM.
• Connect it correctly.
• Replace with new batteries.
• Operate at close distance.
• Check the left/right channel and connect
it/them correctly.
• Connect the antenna correctly.
weak, install the FM antenna in a place
with good reception.
properly?
There is no sound from
• Adjust the volume.
• If the input strength of antenna signal is
• Is the surround speaker connected
surround speakers.
• Press Mute button to cancel the function.
properly?
broadcasts.
There is no sound from
• Connect them correctly.
MISCELLANEOUS
HQ
INSTANT REPLAY
JCL
JCP
JC PENNY
Code Number
• Refer to pages 12~13 to connect them
properly.
• Refer to pages 20~21 to select LARGE or
SMALL.
• Refer to pages 29~35 to select proper
Surround Mode.
• Is the centre speaker connected properly?
• Refer to pages 10~11 to connect it properly.
• Is CEN (centre) incorrectly selected to
• Refer to pages 20~21 to select LARGE or
NONE in speaker setup?
• Is the surround mode selected to stereo?
SMALL.
• Refer to pages 29~35 to select other
Surround Modes.
47
Before calling for service (cont’d)
Symptom
Check
• Refer to pages 10~11 to connect it properly.
connected properly?
There is no sound from
surround back speakers
GENERAL
• Is the S.BACK(Surround Back) selected
to NONE in Speaker Setup?
• Is Surround Mode set to EX/ES?
Specifications
Remedy
• Are the surround back speakers
• Refer to pages 20~21 to select LARGE or
SMALL.
• Refer to page 32 to set Surround Mode
to EX/ES.
• Is S.BACK(Surround Back) selected to
Can't select EX/ES mode.
Can't select Dolby Pro
NONE in Speaker Setup?
• Refer to pages 20~21 to select LARGE or
SMALL.
• Is the input signal selected properly?
• Use 7.1 channel external component.
• Is the input signal selected properly?
• Select 2 channel Dolby Digital, PCM, and
Logic llx mode.
FM TUNER
Analogue input signal.
Can't select NEO:6 mode.
• Is the input signal selected properly?
There is no sound when
playing a DTS encoded
DVD.
• Is Digital input selected?
• Use PCM and Analogue input signal.
AMPLIFIER
• Check whether the DVD player is properly
connected and refer to page 24 to select
the digital input.
FREQUENCY
RESPONSE
VIDEO
OUTPUT
• The protection function will come on if the main unit or power
transformer overheats.
"
" will appear in the display .
This function will come on :
- If speaker terminal is shorted
- If speaker cable is shorted
If there is no problem when you turn the unit on again after
turning it off, PROTECTION mark will disappear on the
display and the unit will work properly.
48
• If PROTECTION appears on the display,
check whether the speaker terminal is shorted
and then turn on the unit
S
P
E
A
K
E
R
S
Power supply
Standby power consumption
Main unit
Power consumption
Subwoofer
Weight
Dimensions (W x H x D)
Operating temperature range
Operating humidity range
Frequency response
Usable sensitivity
S/N ratio
Distortion
Stereo separation
Tuner output level
Rated output
Front speaker(left+right)
Center speaker
Surround speaker(left+right)
Surround back
Input sensitivity/impedance
S/N ratio (analog input)
Separation (1kHz)
Analog input
Digital input/96kHz PCM
TV format
Input level/impedance
Output level/impedance
Video frequency response
S/N ratio
Speaker system
Impedance
Rated input
Maximum input
Dimensions (W x H x D)
Weight
Front / Surround / Surround back
4Ω x 6
100W
200W
100 x 270 x 97 mm
1.4 Kg / 1.2 Kg / 1.2 Kg
230V, 50 Hz
0.9W
100W
90W
5.8 kg
430 x 145 x 350 mm
+5°C~+35°C
10%~75%
87.5~108.0MHz
12dBf
MONO/STEREO 55/55dB
MONO/STEREO 0.3/0.8%
30dB
1kHz, 75kHz Dev
20Hz~20kHz/THD = 10%
4 Ω 100W/CH
4 Ω 100W/CH
4 Ω 100W/CH
4 Ω 100W/CH
450mV/47kΩ
80dB
60dB
20Hz~20kHz(±3dB)
20Hz ~44kHz(±3dB)
NTSC/PAL
1Vp-p/75 Ω
1Vp-p/75 Ω
5Hz to 10kHz(-3dB)
60dB
Centre
4Ω
100W
200W
300 x 90 x 94 mm
1.4 Kg
MISCELLANEOUS
Product protection function
Heat protection
GB
Subwoofer speaker
8Ω
150W
300W
311 x 378 x 443 mm
14.4 Kg
❈ S/N ratio, distortion, separation and usable sensitivity are based on measurement using AES (Audio Engineering Society) guidelines.
49
Download PDF

advertising