Samsung | HT-AS730S | User manual | Samsung HT-AS730S Stereo Receiver User Manual

HT-AS730S
AV Receiver System
user manual
imagine the possibilities
Thank you for purchasing this Samsung product.
To receive more complete service,
please register your product at
www.samsung.com/register
HT-AS730S-XAA_0204.indd 1
2009-02-05 �� 11:46:46
Safety information
Safety Warnings
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE COVER(OR BACK). NO USER-SERVICEABLE PARTS ARE INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CLASS 1 LASER PRODUCT
KLASSE 1 LASER PRODUKT
LUOKAN 1 LASER LAITE
KLASS 1 LASER APPARAT
PRODUCTO LASER CLASE 1
This symbol indicates “dangerous voltage”
inside the product that presents a risk of
electric shock or personal injury.
This symbol indicates important instructions
accompanying the product.
CLASS 1 LASER PRODUCT
This Compact Disc player is classified as a CLASS 1 LASER product.
Use of controls, adjustments or performance of procedures other than
those specified herein may result in hazardous radiation exposure.
CAUTION
~ INVISIBLE LASER RADIATION WHEN OPEN AND
INTERLOCKS DEFEATED, AVOID EXPOSURE TO BEAM.
~ THIS PRODUCT UTILIZES A LASER. USE OF CONTROLS OR
ADJUSTMENTS OR PERFORMANCE OF PROCEDURES
OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN
HAZARDOUS RADIATION EXPOSURE. DO NOT OPEN
COVER AND DO NOT REPAIR YOURSELF. REFER
SERVICING TO QUALIFIED PERSONNEL.
WARNING
~ To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture.
~ To prevent injury, this apparatus must be securely attached to the floor/wall in accordance with the installation
instructions.
CAUTION
~ Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be
placed on the apparatus.
~ The Mains plug is used as a disconnect device and shall stay readily operable at any time.
This product satisfies FCC regulations when shielded cables and connectors are used to connect the unit to other
equipment. To prevent electromagnetic interference with electric appliances, such as radios and televisions, use
shielded cables and connectors for connections.
FCC NOTE (for U.S.A):
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
~ Reorient or relocate the receiving antenna.
~ Increase the separation between the equipment and receiver.
~ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
~ Consult the dealer or an experienced radio/TV technician for help.
Caution : FCC regulations state that any unauthorized changes or modifications to this equipment may void the
user's authority to operate it.
HT-AS730S-XAA_0204.indd 2
2009-02-05 �� 11:46:46
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may cause undesired operation.
EnG
Important Safety Instructions
IMPORTANT NOTE:
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth an uncontrolled environment.
This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Canadian Department of Communications Radio Interference Regulations
This digital apparatus (Wireless Internet Radio) does not exceed the Class B limits for radio-noise emissions from
digital apparatus as set out in the Radio Interference Regulations of the Canadian Department of Communications.
Read these operating instructions carefully before using the unit. Follow all the safety instructions listed below. Keep
these operating instructions handy for future reference.
1) Read these instructions.
2) Keep these Instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7)Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
9)Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with
one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade
or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet.
10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and
the point where they exit from the apparatus.
11) Only use attachment/accessories specified by the manufacturer.
12)Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or
sold with the apparatus. When a cart is used, use caution when moving the cart/
apparatus combination to avoid injury from tip-over.
13) Unplug this apparatus during lightning storms or when unused for long periods of time.
14)Refer all servicing to qualified service personnel. Servicing is required when the apparatus
has been damaged in any way, such as power-supply cord or plug is damaged, liquid has
been spilled or objects have fallen into the apparatus, the apparatus has been exposed to
rain or moisture, does not operate normally, or has been dropped.
HT-AS730S-XAA_0204.indd 3
2009-02-05 �� 11:46:47
Precautions
Ensure that the AC power supply in your house complies with the identification sticker located on the back of your player. Install
your player horizontally, on a suitable base (furniture), with enough space around it for ventilation (3~4inches). Make sure the ventilation slots are not covered. Do not stack anything on top of the amplifier. In order to disconnect the player completely
from the power supply, remove the mains plug from the wall outlet, especially when left unused for a long period of time.
During thunderstorms, disconnect AC main plug from the
wall outlet.
Voltage peaks due to lightning could damage the unit.
Do not expose the unit to direct sunlight or other heat
sources.
This could lead to overheating and malfunction of the unit.
Protect the player from moisture(i.e. vases) , and excess
heat(e.g.fireplace) or equipment creating strong magnetic
or electric fields (i.e.speakers...). Disconnect the power
cable from the AC supply if the player malfunctions. Your
player is not intended for industrial use.
Use of this product is for personal use only.
Condensation may occur if your player or disc have been
stored in cold temperatures.
If transporting the player during the winter, wait
approximately 2 hours until the unit has reached room
temperature before using.
The batteries used with this product contain
chemicals that are harmful to the environment.
Do not dispose of batteries in the general household
trash.
HT-AS730S-XAA_0204.indd 4
2009-02-05 �� 11:46:48
EnG
Features
Digital AV Receiver
DTS
This product is a pure digital AV receiver that performs
digital signal processing to minimize signal distortion and
loss.
Provides a full range of 6 channels by converting a digital
PCM or analog stereo signal using DTS digital matrix
decoding.
Dolby Pro Logic llx
SFE (Sound Field Effect) Using
32bit Audio Digital Signal
Processing
Dolby Pro Logic IIx is a new technology that provides
discrete 7.1 channels out of 2 channel or multi channel
sources.It also provides Music,Movie and Game modes.
Dolby Pro Logic Iix is an improved surround system that
is optimized to a 7.1 CH multimedia system, enabling
you to maximize your entertainment experience.
DTS 96/24
DTS 96/24 encodes standard 16 bit/44.1 kHz sound to
24 bit/96kHz and applies it to a 5.1 CH sound track.
DOLBY DIGITAL EX
Adds a surround back channel for more spacious sound
compared to regular 5.1 channel Dolby Digital.
DTS (Digital Theater Systems)
DTS provides a discrete 5.1 CH digital audio signal for
both music and movie contents and uses less
compression than Dolby Digital for richer sound.
iPod
You can enjoy music files by connecting your iPod
to the AV Receiver with the supplied iPod dock.
Provides more realistic surround sound with normal
stereo audio sources.
Anynet+ (HDMI-CEC) Function
Anynet+ is a function that can be used to operate this
AV Receiver with a Samsung TV remote control, by
connecting the receiver to a SAMSUNG TV using an
HDMI Cable. (This function is available only in
connection with Samsung TV and DVD player
supporting Anynet+(HDMI-CEC).)
DTS-ES
(Extended Surround)
The DTS-ES (Extended Surround) system is a new multi
digital signal format that was developed by Digital
Theater Systems Inc.
Supporting full compatibility with the conventional DTS
digital surround sound format, the DTS-ES (Extended
Surround) system improves the surround signal for a
360-degree surround effect.
DTS-ES adds an additional rear center surround channel
for 6.1 channel sound.
Accessories
Remote control
(AH59-01951K)
FM antenna
(AH42-00017A)
User’s manual
(AH68-02174R)
iPod Dock
(AH97-02650C)
ASC microphone
( AH30-00099A )
HT-AS730S-XAA_0205.indd 5
2009-02-05 �� 3:58:48
Contents
safety information
2
3
4
Safety Warnings
Important Safety Instructions
Precautions
features
5
Accessories
description
8
10
12
13
13
14
Front Panel
Rear Panel
Display
Insert Remote Control Batteries
Operation Range of the Remote Control
Tour of the Remote Control
connections
16
18
19
20
21
22
23
24
25
26
27
29
29
Speaker Positioning
Connecting the Speakers
Connecting the Video Out to your TV
Connecting External Devices/your TV via
HDMI
HDMI Function
Connecting a DVD or BD(Blu-Ray) Player
Connecting a Cable, Satellite or Set-top Box
Connecting a VCR
Connecting a CD Player
Connecting 7.1 Channel Devices
Connecting an iPod
Connecting the FM Antenna
Connecting Aux Components
setup
30
34
35
39
44
Setup Menu Tree
Input Setup
Speaker Setup
Surround Setup
Option Setup
Operation
47
48
49
52
53
54
56
Before Using the AV Receiver
Selecting Digital/Analog Input
Using the Surround Modes
Using the Speaker Adjustment Buttons
Listening to the Radio
Using an iPod
Convenient Functions
2
5
8
16
30
47
HT-AS730S-XAA_0204.indd 6
2009-02-05 �� 11:46:53
EnG
miscellaneous
58
61
appendix
63
● contents
troubleshooting
58 Operating Your TV with the Remote Control
60 Operating Your DVD or BD PLAYER with
Remote Control
61 Troubleshooting
63 Specifications
HT-AS730S-XAA_0205.indd 7
2009-02-05 �� 3:59:01
Description
Front Panel
1
15
2
14
13
12
11 10 9
8 7 6 5 4
3
1
STANDBY/ON button
Sets the AV receiver to Standby.
2
VOLUME Control
Adjusts the volume level.
3
SELECT button
Used to change the radio frequency or select detailed options in Surround mode.
4
TUNING MODE button
Used to select Manual or Auto mode for FM radio.
5
TONE CONTROL button
6
S.DIRECT
7
SURROUND button
Used to adjust the bass and treble level.
* Also used to return to the previous menu from the SETUP menu.
Used to output 2 CH PCM audio signal without any signal processing, providing higher audio quality.
This is useful for obtaining the best sound from a connnected CD player.
* Also used to select an item in the SETUP menu.
Toggles to select a surround sound mode.
* Also used to move the cursor up in the SETUP menu.
HT-AS730S-XAA_0204.indd 8
2009-02-05 �� 11:46:54
EnG
Used to select a connected 7.1 multi channel player
8
7.1CH IN
9
FUNCTION button
10
INPUT MODE
11
SETUP button
Displays the SETUP menu where you can select a menu item (INPUT, SPEAKER, SURROUND,
OPTION).
12
ASC MIC JACK
Used to connect the ASC MIC for setting up ASC (Auto Sound Calibration).
13
AUX IN Jack
Auxiliary AV input terminals used to connect a camcorder, portable DVD player or gaming device.
14
HEADPHONE Jack
Stereo headset input jack.
15
POWER button
Turns the receiver on/off.
* Also used to move the cursor down in the SETUP menu.
Used to select a source (FM, DVD, SAT, TV, VCR, CD, AUX, 7.1 MULTI CH)
* Also used to move the cursor to the right in the SETUP menu.
Toggles to select an input mode for the selected source.
* Also used to move the cursor to the left in the SETUP menu.
● description
HT-AS730S-XAA_0204.indd 9
2009-02-05 �� 11:46:54
Rear panel
1
2
3
4
5 6
7
8
IPOD
17
16 15
14
13 12 11 10 9
1
FM Antenna JACK
Connect the FM Antenna here.
2
7.1 CH ANALOG AUDIO INPUT JACKS
Receives the analog audio signal from an external player with a multi-channel port.
3
VIDEO INPUT JACKS
Receives the video signal from a video player (DVD, SAT, TV, VCR).
4
HDMI INPUT JACKS
Receives digital video and audio signals simultaneously using an HDMI cable.
5
VCR VIDEO OUTPUT JACK
Outputs the video signal to the VCR.
6
MONITOR OUTPUT JACK
Outputs the video signal to video devices (TV, Projector etc).
7
HDMI OUTPUT JACK
Outputs digital video and audio signals simultaneously using an HDMI cable.
8
SPEAKER OUTPUT TERMINALS
Speaker connection terminals
9
COMPONENT VIDEO OUTPUT JACK
Outputs the component video signal.
10
COMPONENT VIDEO INPUT JACKS
Receives the component video signal.
11
SUBWOOFER AUDIO OUTPUT JACK
Connect the subwoofer.
10
HT-AS730S-XAA_0204.indd 10
2009-02-05 �� 11:46:56
Receives the audio signal from an audio CD player.
13
VCR AUDIO OUTPUT JACK
Outputs the audio signal to a VCR.
14
AUDIO INPUT JACKS
Receives the audio signal from a video player.
15
IPOD INPUT JACK
Receives the audio/video signal from an iPod.
16
COAXIAL INPUT JACK (DIGITAL AUDIO IN)
Receives the digital coaxial audio signal.
17
OPTICAL INPUT JACKS (DIGITAL AUDIO IN)
Receives the digital optical audio signal.
● Description
CD AUDIO INPUT JACKS
EnG
12
11
HT-AS730S-XAA_0204.indd 11
2009-02-05 �� 11:46:56
Display
1
2
3 4
5
7
1
SPEAKER INDICATORS
Receives the audio/video signal from an iPod.
2
LISTENING MODE INDICATORS
Displays the current listening mode.
3
TUNING INDICATORS
Displays the status of the current radio broadcasting.
4
AUDIO INPUT INDICATORS
Displays the input signal type of the current audio source.
5
VOLUME LEVEL INDICATOR
Displays the volume level.
6
RADIO FREQUENCY INDICATOR
Displays the current radio frequency range.
7
MESSAGE DISPLAY
Informs you of the status of the receiver.
6
12
HT-AS730S-XAA_0204.indd 12
2009-02-05 �� 11:46:57
M
2. Install two AAA size batteries.
Make sure to match the “+” and “–”
ends of the batteries with the diagram
inside the compartment.
3. Replace the cover.
Assuming typical TV usage, the
batteries last for about one year.
● Description
1. Lift the cover at the back of the
remote control upward as shown.
EnG
Insert remote control batteries
Follow these precautions to avoid leaking or cracking cells:




Place batteries in the remote control so they match the polarity : (+) to (+) and (–) to (–).
Use the correct type of batteries. Batteries that look similar may differ in voltage.
Always replace both batteries at the same time.
Do not expose the batteries to heat or a flame.
operation Range of the remote control
The remote control can be used up to approximately 23 feet/7 meters in a straight line. It can also be operated at a
horizontal angle of up to 30° from the remote control sensor.
13
HT-AS730S-XAA_0205.indd 13
2009-02-05 �� 4:00:14
Tour of the Remote Control
14
HT-AS730S-XAA_0213.indd 14
2009-02-16 �� 2:54:57
POWER button
Turns the receiver on/off.
2
INPUT MODE button
Toggles to select an input mode for the selected source.
3
SLEEP button
Used to set the Sleep Timer.
4
NUMBER buttons
Used to select a TV channel.
5
SPK LEVEL/ SPK SELECT/
TEST TONE buttons
Used to select and adjust the level of a desired speaker. Also used to select the Test Tone
function.
6
MO/ST button
Select MONO or STEREO for radio broadcasting.
7
TUNER MEMORY button
Used to set a preset radio frequency.
8
VOLUME CONTROL buttons
Adjusts the volume of the selected device.
9
S.DIRECT button
Used to output 2CH PCM audio without any signal processing, providing higher audio quality.
This is useful for obtaining the best sound from a connected CD player.
10
SETUP/MENU button
Displays the SETUP menu where you can select a menu item (INPUT, SPEAKER, SURROUND,
OPTION).
11
UP/DOWN/LEFT/RIGHT
buttons
Used to navigate the menus.
12
INFO button
Displays information on the connected device currently being used.
13
SURROUND mode buttons
Used to select a surround sound mode.
14
STEREO button
Outputs the sound of the selected source in 2 CH stereo.
15
DIMMER button
Adjusts the brightness of the display.
16
FUNCTION button
Toggles to find and select an input source.
17
SELECT DEVICE buttons
Select one from the 4 provided sources that you want to control using the remote control.
18
PAUSE button
Pauses playback on a connected device.
19
TUNING MODE button
Used to select Auto or Manual mode for FM radio.
20
EXTERNAL DEVICE
PLAYBACK buttons
Used to control playback functions on external devices.
21
MUTE button
Mutes the sound of a connected device.
22
TUNING/CHANNEL buttons
Used to change the radio broadcasting frequency or TV channel.
23
RETURN button
Used to return to the previous menu from the SETUP menu.
24
ENTER button
Used to select an item in the SETUP menu.
25
EXIT button
Exits the SETUP menu.
26
ASC button
Used to set the ASC function.
27
FUNCTION selector buttons
Used to select an input source.
EnG
1
● Description
15
HT-AS730S-XAA_0204.indd 15
2009-02-05 �� 11:46:59
Connections
This section involves various methods of connecting the AV receiver to other
external components.
Before moving or installing the product, be sure to turn off the power and
disconnect the power cord.
Speaker positioning
SL
SR
SBL
SBR
Position of AV Receiver
Place AV Receiver on a dedicated stand or rack.
Subwoofer
The position of the subwoofer is not so critical. Place it
anywhere you like.
SBL
SBR
Subwoofer function
Active subwoofer with integrated 150W amplifier provides rich
bass sound.
~ Connect the SW OUT terminal of the amplifier to the
INPUT terminal of the subwoofer speaker.
~ Press the POWER button on the rear side of the subwoofer to turn the power on.
~ Using the subwoofer’s VOLUME control, you can set the desired bass level
(See page 37 "Setting the speaker level" to set the subwoofer level in the menu).
Front Speakers
Place these speakers in front of your listening position, facing inwards (about 45°) toward you.
Place the speakers so thatSBL
their tweeters
SBRwill be at the same height as your ears.
SBL
SBR
lign the front face of the front speakers with the front face of the center speaker or place them slightly
A
in front of the center speaker.
16
HT-AS730S-XAA_0204.indd 16
2009-02-05 �� 11:47:01
EnG
Speaker positioning (continued)
Center speaker
It is best to install it at the same height as the front speakers.
You can also install it directly over or under the TV.
SBL
SBL
Surround Speakers
SBR
SBR
SBL
SBR
● connections
Place these speakers behind your listening position.
If there isn't enough room, place these speakers so they face each other.
Place them about 2 to 3 feet (60 to 90cm) above your ears, facing slightly downward.
Unlike the front and center speakers, the surround speakers are used to handle mainly sound effects
and sound will not come from them all the time.
SBL SBL SBR SBR
Surround Back Speakers
If you are using two rear center speakers, place them facing forward from behind the listening position.
Place the surround back speaker about 2.3-3.3feet (70 cm to 1 m).
M`
When you attach the speakers to a wall, make sure to fasten them tightly so they do not fall off.
Speaker Configuration
For the best surround-sound experience, you should connect seven speakers and a powered
subwoofer.
The following table shows which channels you should use based on the number of speakers you have.
2 speakers
3 speakers
4 speakers
5 speakers
6 speakers
7 speakers
SBL
SBL
SBR SBL
SBR SBL
SBR SBL
SBR SBL
SBR SBL
SBL
SBL
SBR SBL
SBR SBL
SBRSBL
SBL
SBR SBL
SBR SBL
SBL
SBRSBL
SBR
SBRSS
SBR
SBR
SBR
If you’re using only one surround back speaker, connect it to the SURR BACK L terminals.
` No matter how many speakers you use, a powered subwoofer is recommended for powerful and solid bass.
17
HT-AS730S-XAA_0204.indd 17
SBR
SBR
SBR SBL
SBL
M`
SBR SBL
2009-02-05 �� 11:47:02
COnneCting tHe SpeakerS
FRONT (R)
FRONT (L)
CENTER
ACTIVE SUBWOOFER
(BUILT-IN POWER AMPLIFIER)
AV RECEIVER
SURROUND (R) SURROUND
BACK (R)
(not supplied)
SURROUND SURROUND (L)
BACK (L)
(not supplied)
Connecting Speaker Wire
1. Loosen the knob by turning counterclockwise.
2. Insert the bare part of the wire into the hole in the side of
each terminal.
3. Tighten the knob by turning clockwise to secure the wire.
M`
Keep the subwoofer speaker out of reach of children to prevent them from inserting their hands or objects
into the duct (hole).
` Never touch speaker terminals while the power is on. Doing so could result in electric shock.
` Make sure the polarities (+ and -) are correct.
Connecting the Speakers
1. Press down the terminal tab on the back of the speaker.
2. Insert the black wire into the black terminal (–) and the red wire into the
red (+) terminal, and then release the tab.
3. Connect the connecting plugs to the back of the AV Receiver.
~ Make sure the colors of the speaker terminals on the back of the
AV receiver match the colors of the connecting plugs.
Black
Red
1
HT-AS730S-XAA_0204.indd 18
2009-02-05 �� 11:47:08
EnG
Connecting the Video Out to your TV
● Connections
OPTICAL
OUT
AUDIO
OUT
VIDEO
IN
COMPONENT
IN
Video Connection
If your television is equipped with Component Video inputs, connect a Component video cable(not
supplied) from the Component Video Output (PR, PB and Y) jacks on the back of your AV Receiver to the
Component Video Input jacks on your TV.
OR
Connect the Video cable from the VIDEO OUT (MONITOR) jack on the back of your AV Receiver to the
Video Input jack on your TV.
Audio Connection
Connect the Digital Input (OPTICAL 3) on your AV Receiver to the Digital Output of the TV.
OR
Connect AUDIO IN (TV) on your AV Receiver to the Audio Out of the TV.
19
HT-AS730S-XAA_0206.indd 19
2009-02-06 �� 9:42:51
Connecting external devices/YOUR TV Via HDMI
HDMI is a digital standard interface for connection to such devices as a TV, projector, DVD player, Blu-ray player, settop
box and more.
HDMI removes any loss of signal from analog conversion, enabling you to enjoy video and audio sound quality as it was
originally created in the digital source.
By connecting through the HDMI(High-Definition Multimedia Interface) interface, you can play back digital video and audio.
DVD or Blu-RAY Player
• Connect it if you want
to use Anynet+.
SAT(Cable/Satellite/Set-top box)
game console
TV
OPTICAL
OUT
High-bandwidth Digital Content Protection System (HDCP) support
To play digital contents through the HDMI connection, both of the connected external device and TV
must support High-bandwidth Digital Content Protection System (HDCP). This product supports HDCP.
Compatibility with a TV Supporting HDMI
M`
A TV with an HDMI jack.
Video/Audio
A TV with a DVI-D jack (TV supporting HDCP)
Video
A TV with a DVI-D jack (TV not supporting HDCP)
-
Audio from SACD discs will not be heard. To play a DVD disc whose copyright is protected by CPPM, use a
player supporting CPPM.
` The quality of the audio output through the HDMI jack (sampling frequency and bit rate) may be limited by the
performance of the connected device.
` Since HDMI connection supports both video and audio, you don’t have to connect an additional audio cable.
20
HT-AS730S-XAA_0204.indd 20
2009-02-05 �� 11:47:13
EnG
HDMI FUNCTION
Using Anynet+(HDMI-CEC)
Anynet+ is a function that enables you to control other Samsung Devices with your Samsung TV's
remote control. Anynet + can be used by connecting this AV Receiver to a SAMSUNG TV using an
HDMI Cable. This is only available with SAMSUNG TVs that support Anynet+.
1. Connect the AV receiver to a Samsung TV with an HDMI cable. (See page 20)
● Connections
2. Set the Anynet+ function on your TV.
(See the TV instructions manual for more information.)
~ You can operate the volume on the AV receiver by using Volume buttons on the TV remote
control.
DVDR 1
View TV
DVDR 1 Menu
DVDR 1 Operation
Receiver : On
Connect DVDR 2
Setup
If you select the TV
Set the Anynet+(HDMI-CEC) to On by pressing the Anynet+ button on your TV.
~ Receiver : On : You can listen to audio through the AV Receiver.
~ Receiver : Off : You can listen to audio through the TV.
DTV Air 11-1
Receiver : On
Connect DVDR 1
Connect DVDR 2
Setup
MOVE ENTER
ENTER
MOVE
Move
EXIT
EXIT
If you select the DVD Player
Select THEATER to connector and set the option of each item below.
~ View TV : If Anynet+(HDMI-CEC) set to on and you select View TV,
the AV receiver will automatically switch to SAT
OPTIC2(DIGITAL IN).
~ Receiver : On : You can listen to audio through the AV receiver.
~ Receiver : Off : You can listen to audio through the TV.
Enter
Exit
DVDR 1
View TV
DVDR 1 Menu
DVDR 1 Operation
Receiver : On
MOVE
ENTER
Connect DVDR 2
EXIT
Setup
To turn off Anynet+
1. Press SETUP/MENU button, and then press the ENTER button.
~ “SETUP MODE” appears on the display and goes into Setup Mode.
DTV Air 11-1
Receiver : On
Connect DVDR 1
2. Press ◀▶ button to select the “ANYNET+ MODE”, and then press the ENTER button.
Connect DVDR 2
Setup
. Press the ▲▼button to set ANYNET+ to OFF.
- If you are using Anynet+, set ANYNET+ to ON and if not, set it to OFF.
Move
Enter
- To exit setup mode~ Press SETUP/MENU, EXIT or RETURN button.
“SETUP OFF” appears on the display and Setup Mode is exited.
M`
If you use an HDMI cable to connect a Samsung TV to your AV Receiver, you can operate the AV receiver using
the TV’s remote control. This function is available only in connection with Samsung TV and DVD player
supporting Anynet +(HDMI-CEC).
` Please check your TV for the n logo. If your TV has an n logo, then it supports the Anynet+
function.
` When you are making Anynet+ connection, do not connect more than two AV receivers (Anynet+ installed).
Otherwise, it can cause a malfunction.
` Anynet+ does not work if the function is set to iPod AUDIO.
21
HT-AS730S-XAA_0204.indd 21
2009-02-05 �� 11:47:17
Exit
Connecting a DVD or BD(Blu-Ray) Player
DVD or BD Player
OPTICAL
OUT
AUDIO
OUT
VIDEO
OUT
COMPONENT
OUT
VIDEO
IN
or
COMPONENT
IN
or
or
Video Connection
Connect a Component video cable(not supplied) from the COMPONENT IN (DVD) (PR, PB and Y) jacks
on the back of your AV Receiver to the Component Video Output jacks on your DVD/BD player.
OR
Connect a Video cable from the VIDEO IN (DVD) jack on the back of your AV Receiver to the Video
Output jack on your DVD/BD player.
Audio Connection
Connect the Digital Input (OPTICAL 1) on your AV Receiver to the Digital Output of the DVD/BD player.
OR
Connect AUDIO IN (DVD) on your AV Receiver to the Audio Out of the DVD/BD player.
22
HT-AS730S-XAA_0204.indd 22
2009-02-05 �� 11:47:19
EnG
Connecting a Cable, Satellite or Set-top box
SAT(Cable/Satellite/Set-top box)
AUDIO
OUT
VIDEO
OUT
COMPONENT
OUT
VIDEO
IN
or
● Connections
OPTICAL
OUT
COMPONENT
IN
or
or
Video Connection
Connect a Component video cable(not supplied) from the COMPONENT IN (SAT) (PR, PB and Y) jacks
on the back of your AV Receiver to the Component Video Output jacks on your SAT.
OR
Connect a Video cable from the VIDEO IN (SAT) jack on the back of your AV Receiver to the Video
Output jack on your SAT.
Audio Connection
Connect the Digital Input (OPTICAL 2) on your AV Receiver to the Digital Output of the SAT.
OR
Connect AUDIO IN (SAT) on your AV Receiver to the Audio Out of the SAT.
M`
Disconnect the power plug from the outlet if you will not use this unit for a long period of time.
` If the external component has only one audio output jack, connect it to either the right or left audio input jack
of the main unit. Connect the audio cable's red plug to the red jack and white cable to the white jack.
` If your use the AV Receiver to control your DVD/BD player, the pause function will not work.
23
HT-AS730S-XAA_0204.indd 23
2009-02-05 �� 11:47:22
COnneCting a VCr
VCR
AUDIO
OUT
VIDEO
OUT
VIDEO
IN
AUDIO
IN
VIDEO
IN
(For playback)
(For recording)
Video Connection
for playback
Connect a Video cable from the VIDEO IN (VCR) jack on the back of your AV Receiver to the Video
Output jack on your VCR.
for recording
Connect a Video cable from the VIDEO OUT (VCR) jack on the back of your AV Receiver to the Video
Input jack on your VCR.
audio Connection
for playback
Connect AUDIO IN (VCR) on your AV Receiver to the Audio Out of the VCR.
for recording
Connect AUDIO OUT (VCR) on your AV Receiver to the Audio In of the VCR.
M`
Disconnect the power plug from the outlet if you will not use this unit for a long period of time.
HT-AS730S-XAA_0204.indd 24
2009-02-05 �� 11:47:25
EnG
Connecting a CD player
CD player
● Connections
AUDIO
OUT
COAXIAL
OUT
or
Audio Connection
Connect the Digital Input (COAXIAL) on your AV Receiver to the Digital Output of the CD Player.
OR
Connect AUDIO IN (CD) on your AV Receiver to the Audio Out of the CD player.
M`
If the external component has only one audio output jack, connect it to either the right or left audio input jack
of the main unit. Connect the audio cable's red plug to the red jack and white cable to the white jack.
25
HT-AS730S-XAA_0204.indd 25
2009-02-05 �� 11:47:27
Connecting 7.1 channel devices
You can connect the AV receiver to a DVD player, SUPER AUDIO CD player or other device with 7.1 channel output.
SW
C
SW
FRONT
SURROUND
C
SUB
CENTER
WOOFER
SURROUND
BACK
5.1 CH
7.1 CH
7.1 Channel device
26
HT-AS730S-XAA_0204.indd 26
2009-02-05 �� 11:47:28
You can listen to the audio from an iPod through the main unit. For iPod operation with your receiver, see pages 28
and 54 ~ 55.
EnG
Connecting an iPod
● connections
IPOD
1. Connect the iPod dock connector to the iPod jack on your reciever.
. Place the iPod in the Dock.
~ If you want to play a movie stored in your iPod player, you should set the player's TV Out option to
On before inserting it into the dock. See page 55.
. Press the IPOD button on the remote control.
~ You can also use the FUNCTION button on the main unit.
The mode switches as follows :
FM  DVD  SAT  TV  VCR  CD  AUX  7.1 MULTI CH  IPOD AUDIO
 IPOD VIDEO.
Disconnecting an iPod
Follow the steps below to prevent damage to an iPod and data when disconnecting from your
AV receiver.
1. Press the FUNCTION button on the main unit to switch to a mode other than IPOD AUDIO or
IPOD VIDEO.
OR
1. Turn off the AV Receiver.
2. Disconnect the iPod player from the iPod dock, or remove the iPod dock connector from the AV
receiver.
M`
`
`
`
`
You must have the VIDEO (Monitor or VCR) output connected to your TV to view iPod video.
See page 24.
Adjust the volume to a moderate level before you connect your iPod and AV Receiver.
When the unit is powered on and you connect an iPod, the unit will charge your iPod's battery.
Make sure to connect the dock connector so that the label “SAMSUNG” faces upward.
“Made for iPod” means that an electronic accessory has been designed to connect specifically to iPod and has
been certified by the developer to meet Apple performance standards.
27
HT-AS730S-XAA_0204.indd 27
2009-02-05 �� 11:47:30
Connecting an iPod (Continued)
iPod models that are compatible with Ht-AS730S
M`
“Made for iPod” means that an electronic accessory has been designed to connect specifically to iPod and has been
certified by the developer to meet Apple performance standards.
` Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards.
iPod is a trademark of Apple Inc., registered in the U.S. and other countries.
28
HT-AS730S-XAA_0204.indd 28
2009-02-05 �� 11:47:31
ENG
COnneCting tHe fm antenna
1. Connect the FM antenna supplied to the FM 75Ω COAXIAL terminal as a temporary measure.
2. Slowly move the antenna wire around until you find a location where reception is good, then fasten it to a wall or
other rigid surface.
● COnneCtiOnS
FM antenna (supplied)
M
` Do not place the antenna cable close to the power cord. Keep it as far away as possible.
` If you experience poor FM reception, use an external antenna.
COnneCting aUX COmpOnentS
You can connect external devices you use for a short time (camcorder, game console, mobile equipment,etc.) to
the front of this unit for convenience.
VIDEO
OUT
AUDIO
OUT
Camcorder
HT-AS730S-XAA_0204.indd 29
2009-02-05 �� 11:47:35
setup
For your convenience, you can set this AV receiver's features for the best use.
Setup MENU TREE
Here’s a quick look at how the setup menus are organized on your AV Receiver.
INPUT
DVD
OPTICAL 1,2,3
COAXIAL
OPTICAL 1,2,3
COAXIAL
OPTICAL 1,2,3
COAXIAL
OPTICAL 1,2,3
COAXIAL
OPTICAL 1,2,3
COAXIAL
SAT
TV
CD
AUX
SPEAKER
SURROUND
OPTION
30
HT-AS730S-XAA_0204.indd 30
2009-02-05 �� 11:47:35
EnG
Setup MENU TREE (Continued)
INPUT
SPEAKER
SPEAKER SIZE
● setup
FRONT
LARGE
SMALL
LARGE
SMALL
NONE
LARGE
SMALL
NONE
LARGE
SMALL
NONE
ON
OFF
CENTER
SURROUND
SURROUND BACK
SUBWOOFER
CROSS OVER
60Hz, 80Hz, 100Hz, 120Hz, 150Hz, 180Hz, 200Hz
SPEAKER DISTANCE
FRONT LEFT
FRONT RIGHT
CENTER
SURROUND LEFT
SURROUND RIGHT
1 ~ 30 feet (1 foot steps) , default : 10 feet
SURROUND BACK LEFT
SURROUND BACK RIGHT
SUBWOOFER
SPEAKER LEVEL
FRONT LEFT
FRONT RIGHT
CENTER
SURROUND LEFT
SURROUND RIGHT
-10.0 ~ +10.0dB (1dB step) , default : 0dB
SURROUND BACK LEFT
SURROUND BACK RIGHT
SUBWOOFER
TEST TONE
AUTO
MANUAL
SURROUND
OPTION
31
HT-AS730S-XAA_0204.indd 31
2009-02-05 �� 11:47:36
Setup MENU TREE (Continued)
INPUT
SPEAKER
SURROUND
STEREO
STEREO
MULTI CH STEREO
PL IIx
MODE
Movie
Music
OFF
ON
Game
Matrix
PL
PANORAMA
DIMENSION
-7 ~ STD ~ +7
CENTER WIDTH
0~7
SFE
HALL1
HALL2
JAZZ CLUB
CHURCH
ROCK
CLASSIC
LIVE
GAME
MOVIE
NEO:6
NEO:6 MODE
MUSIC
CINEMA
CENTER IMAGE
0~7
EX/ES
AUTO
OFF
ON
TONE CONTROL
TONE SET
OFF
ON
BASS
-6dB ~ +6dB (1dB Step)
TREBLE
-6dB ~ +6dB (1dB Step)
OPTION
32
HT-AS730S-XAA_0204.indd 32
2009-02-05 �� 11:47:36
EnG
Setup MENU TREE (Continued)
INPUT
SPEAKER
SURROUND
OPTION
● setup
A/V Sync
Delay
0 ~ 200mS (10mS Step)
MP3 ENHANCER
OFF
ON
OFF
ON
SMART VOLUME
ASC SETUP
Auto Setup
DRC
Max
Std
Min
HDMI SETUP
AUTO LIPSYNC
ON
OFF
AVR
TV
On
Off
HDMI Audio
Anynet+
33
HT-AS730S-XAA_0204.indd 33
2009-02-05 �� 11:47:36
INPUT SETUP
Selecting a source device and connection jack
Select the external devices you have connected to the receiver.
1. Press SETUP/MENU button
~ “INPUT” appears on the display and goes into Setup Mode.
2. Press the ▶ button to select a desired device.
3. Press the ▲ or ▼ button to select a desired jack.
- To exit setup mode ~ Press SETUP/MENU, EXIT or RETURN button.
“SETUP OFF” appears on the display and Setup Mode is exited.
- Digital Audio Input Select INPUT JACK
AUDIO
Default
DVD
OPTIC1,2,3,COAX
OPTIC1
SAT
OPTIC1,2,3,COAX
OPTIC2
TV
OPTIC1,2,3,COAX
OPTIC3
CD
OPTIC1,2,3,COAX
COAX
AUX
OPTIC1,2,3,COAX
OPTIC1
SOURCE DEVICE
M`
You can also use SETUP, , , , ,
(ENTER), (RETURN) and
(EXIT) buttons on the front of your AV
Receiver.
` To move up one level from SETUP/MENU or EXIT SETUP when the SETUP mode is released, press the RETURN
button.
34
HT-AS730S-XAA_0204.indd 34
2009-02-05 �� 11:47:38
EnG
SPEAKER SETUP
Setting the speaker size
Signal outputs and frequency response from the speaker will be
adjusted according to your speaker configuration and whether certain
speakers are used or not.

2. Press ▲▼ button to select “SPEAKER”, and then press the
ENTER.
● setup
1. Press SETUP/MENU button.
~ “INPUT” appears on the display.

3. Press ▲▼ button to select “SPK SIZE”, and then press the
ENTER or ▶ button.
4. Press ◀▶ button to select the speaker you want.
~ Each time you press this button, FRONTCEN  SURR 
S.BACK  S.W  CROVR will be selected in turn.

5. Press ▲▼ button to set the mode (LARGE, SMALL etc.) for
the selected speaker.
6. Repeat steps 3-4 to set the mode for each speaker.
- To exit setup mode ~ Press SETUP/MENU, EXIT or RETURN button.
“SETUP OFF” appears on the display and Setup Mode is exited.
Setting the Speaker
SPEAKER
Possible Settings
Default Setting
FRONT(Front)
LARGE, SMALL
SMALL
CEN(Center)
LARGE, SMALL, NONE
SMALL
SURR(Surround)
LARGE, SMALL, NONE
SMALL
S.BACK (Surround Back)
LARGE, SMALL, NONE
SMALL
SUB(Subwoofer)
ON, OFF
ON
CROVR (Crossover Frequency)
60, 80, 100,120, 150, 180, 200(Hz)
150Hz
~
~
~
~
~
~
LARGE : Select when using large speakers. You can listen to full range sound.
SMALL : Select this when using small speakers
NONE : Select when no speaker is used
ON (subwoofer) : Select when using the subwoofer speaker.
OFF (subwoofer) : Select when not using the subwoofer speaker.
CROVR : Select the crossover frequency for the best bass response in your room.
35
HT-AS730S-XAA_0204.indd 35
2009-02-05 �� 11:47:40
SPEAKER SETUP (Continued)
Setting the speaker listening distance
If the speakers cannot be placed at equal distances from the listening
position, you can adjust the delay time of the audio signals from the
center and surround speakers.
1. Press SETUP/MENU button.
~ “INPUT” appears on the display and goes into Setup Mode.
2. Press ▲▼ button to select "SPEAKER", and then press the
ENTER.
3. Press ▲▼ button to select "SPK DISTANCE", and then press
the ENTER or ▶ button.
4. Press ◀▶ button to select the speaker you want.
~ Each time you press this button, F.L  F.R CEN  S.L
 S.R  SBL  SBR  S.W will be selected in turn.



5. Press ▲▼ button to set the speaker distance.
~ For FRONT LEFT, FRONT RIGHT, CENTER, SURR. LEFT,
SURR. RIGHT, SURR. BACK LEFT, SURR. BACK RIGHT,
SUBWOOFER Speaker, you can set the distance from the speaker to listening position between
1ft ~ 30ft (0.3~9.0m) in intervals of 1ft (0.3m).
- To exit setup mode ~ Press SETUP/MENU, EXIT or RETURN button.
“SETUP OFF” appears on the display and Setup Mode is exited.
- Setting Speaker Distance Set the distance from the speaker to listening position in intervals of 1ft(0.3m).
• F.L (front left) : 1ft ~ 30ft
• F.R (front right) : 1ft ~ 30ft
• SBR (surround back right) : 1ft ~ 30ft
• S.L (surround left) : 1ft ~ 30ft
M`
• CEN (center) : 1ft ~ 30ft
• S.R (surround right) : 1ft ~ 30ft
• SBL (surround back left) : 1ft ~ 30ft
• SW (subwoofer) : 1ft ~ 30ft
If the listening position is beyond the range of the speaker distance setup, set the speaker
distance to the maximum.
` The distance range of the overall speaker system is determined based on the F.L(front left)
speaker distance from the listening position.
` Based on the max delay channel, the distance of the front speaker is 4.9ft(5ms) and the
surround speaker can be set up to 14.7ft(15ms).
36
HT-AS730S-XAA_0204.indd 36
2009-02-05 �� 11:47:41
EnG
SPEAKER SETUP (Continued)
Setting the speaker level
You can set the balance and level of speakers.
1. Press SETUP/MENU button.
~ “INPUT” appears on the display and goes into Setup Mode.
3. Press ▲▼ button to select "SPK LEVEL", and then press the
ENTER or ▶ button.
4. Press ◀▶ button to select the speaker you want.
~ Each time you press this button, F.L  F.R CEN  S.L
 S.R  SBL  SBR  S.W will be selected in turn.
5. Press ▲▼ button to set the speaker mode.
~ You can adjust it from -10 to +10dB in 1 step increments.
~ The sound gets quieter at -10dB and louder at +10dB.

● setup
2. Press ▲▼ button to select "SPEAKER", and then press the
ENTER.


- To exit setup mode ~ Press SETUP/MENU, EXIT or RETURN button.
“SETUP OFF” appears on the display and Setup Mode is exited.
Setting Speaker Level
• F.L (front left) : -10 ~ +10dB
• F.R (front right) : -10 ~ +10dB
• CEN (center) : -10 ~ +10dB
• S.L (surround left) : -10 ~ +10dB
• S.R (surround right) : -10 ~ +10dB
• SBL (surround back left) : -10 ~ +10dB
• SBR (surround back right) : -10 ~ +10dB
• S.W (subwoofer) : -10 ~ +10dB
37
HT-AS730S-XAA_0204.indd 37
2009-02-05 �� 11:47:43
SPEAKER SETUP (Continued)
Setting the test tone
Use the test tone to check the speaker connection status or level.
1. Press SETUP/MENU button.
~ “INPUT” appears on the display and goes into Setup Mode.
2. Press ▲▼ button to select "SPEAKER", and then press the
ENTER.
3. Press ▲▼ button to select "TEST TONE", and then press the
ENTER or ▶ button.
4. Press ▲▼ button to select the option you want, and then
press the ENTER or ▶ button.
~ AUTO : Test signal will be automatically output as follows;
F.L  CEN  S.W F.R  S.R  SBR  SBL­­­­  S.L.
- During test tone output, press ▲▼ button to adjust the
speaker output level from -10 to +10 dB
by 1 step.



~ MANU (MANUAL): Enables you to adjust the output level of the speaker manually.
1) Press ◀▶ button to select the speaker you want.
Each time you press ◀▶ button, F.L  CEN  S.W F.R  S.R  SBR  SBL­­­­  S.L will
be selected in turn.
2) Press ▲▼ button to set the test tone as you want.
You can adjust the speaker output level from -10 to +10dB by 1 step.
The sound gets quieter at -10dB and louder at +10dB.
Test Tone Output
• F.L (front left) : -10 ~ +10dB
• CEN (center) : -10 ~ +10dB
• S.R (surround right) : -10 ~ +10dB
• SBR (surround back right) : -10 ~ +10dB
• S.W (subwoofer) : -10 ~ +10dB
• F.R (front right) : -10 ~ +10dB
• SBL (surround back left) : -10 ~ +10dB
• S L (surround left) : -10 ~ +10dB
- To stop test tone ~ Press SETUP/MENU or EXIT button once time.
“SETUP OFF” appears on the display and test tone stops.
38
HT-AS730S-XAA_0204.indd 38
2009-02-05 �� 11:47:45
EnG
SURROUND SETUP
Setting the stereo mode
You can select this mode when listening to sound through the front left
and right speakers and subwoofer.

● setup
1. Press SETUP/MENU button.
~ “INPUT” appears on the display and goes into Setup Mode.
2. Press ▲▼ button to select "SURROUND", and then press the
ENTER.
3. Press ▲▼ button to select "STEREO", and then press the
ENTER or ▶ button.

4. Press ▲▼ button to set STEREO mode you want.
~ STEREO:2CH : Select this for 2 CH stereo output.
~ STEREO:MULTI : Select this for Multi-CH output.

- To exit setup mode ~ Press SETUP/MENU, EXIT or RETURN button.
“SETUP OFF” appears on the display and Setup Mode is exited.
39
HT-AS730S-XAA_0204.indd 39
2009-02-05 �� 11:47:47
SURROUND SETUP (Continued)
Setting Dolby Pro Logic II X mode
This mode provides 7.1 channel sound from 2 channel sources.
1. Press SETUP/MENU button.
~ “INPUT” appears on the display and goes into Setup Mode.
2. Press ▲▼ button to select "SURROUND", and then press the
ENTER.
3. Press ▲▼ button to select "PL II x", and then press the
ENTER or ▶ button.


4. Press ▲▼ button to select the option you want, and then
press the ENTER or ▶ button.
~ MODE : Each time you press ▲▼ button, MOVIE  MUSIC
 GAME  MATRIX  PL will be selected in turn.
MOVIE : Adds realism to the movie soundtrack.
MUSIC : Provides 7.1 channel surround sound for digital, analog or existing stereo sources such as CD,
TAPE, FM, TV and stereo VCR.
GAME : Enhances the excitement of the game’s sound.
MATRIX : You will hear 7.1 channel surround sound.
PL : You will experience a surround effect with just the front left and right speakers.



~ PANORAMA : You can set it ON or OFF.
(This mode extends the front stereo image to include the
surround speakers for an exciting "wraparound" effect with side wall imaging.)
~ DIMENSION : You can set from -7 to +7.
(Incrementally adjusts the sound field (DSP)from the front or surround.)
~ CENTER WIDTH : You can set from 0 to 7.
(This sets the width of the center image. The higher the setting, the less sound comes from the
center speaker.)
M`
PANORAMA, DIMENSION and CENTER WIDTH settings are enabled only if the mode is set to
"MUSIC".
` You cannot use Dolby Pro Logic llx mode for multi channel signals such as Dolby Digital and DTS.
` Pro Logic works only for PCM audio signals with sampling frequencies of 32KHz, 44KHz or
48KHz.
` Sound will not be output from the surround back speakers if the PCM audio signal is mono.
40
HT-AS730S-XAA_0204.indd 40
2009-02-05 �� 11:47:50
EnG
SURROUND SETUP (Continued)
Setting SFE(Sound Field Effect) mode
The SFE (Sound Field Effect) function uses 9 different DSP sound field
effects to digitally simulate actual music environments such as concert
halls or cinemas.
2. Press ▲▼ button to select "SURROUND", and then press the
ENTER.
3. Press ▲▼ button to select "SFE", and then press the ENTER
or ▶ button.
4. Press ▲▼ button to set the Sound Field Effect you want.
~ Each time you press the button, HALL 1 HALL 2 JAZZ
CLUB  CHURCH  ROCK  CLASSIC  LIVE  GAME
 MOVIE will be selected in turn.

● setup
1. Press SETUP/MENU button.
~ “INPUT” appears on the display and goes into Setup Mode.


Setting NEO:6 mode
You can play back 2 channel sound over 6.1 channels when enjoying
music or a movie.
1. Press SETUP/MENU button.
~ “INPUT” appears on the display and goes into Setup Mode.

2. Press ▲▼ button to select "SURROUND", and then press the
ENTER.
3. Press ▲▼ button to select "NEO:6", and then press the
ENTER or ▶ button.

4. Press ▲▼ button to set the NEO:6 mode you want.
~ NEO:6 MODE : Each time you press ▲▼ button, MUSIC
 CINEMA will be selected in turn.
This mode decodes 2 channel signals to a high precision
digital matrix decoder for 6.1 channel sound.
MUSIC : NEO:6 MUSIC mode is optimized for music
playback
CINEMA : NEO:6 CINEMA mode is optimized for movie
playback.


~ CENTER IMAGE : Press ▲▼ button to set the sound image you want.
You can set the sound image from 0 to 7
This parameter adjusts the height of the center image through the front and center speakers. “0”
is the lowest while “7” is the highest.
- To exit setup mode~ Press SETUP/MENU, EXIT or RETURN button.
“SETUP OFF” appears on the display and Setup Mode is exited.
M`
NEO:6 mode cannot be used with DTS and Dolby Digital multi channel signals.
` Pro Logic works only for PCM audio signals with sampling frequencies of 32KHz, 44KHz or
48KHz.
41
HT-AS730S-XAA_0204.indd 41
2009-02-05 �� 11:47:53
SURROUND SETUP (Continued)
Setting EX/ES mode
When surround back speakers are connected, you can listen to 6.1 or 7.1 multi-channel sound using the built-in
Dolby Digital Surround EX or DTS ES decoder. This function works when a Dolby Digital or DTS source (such as a
DVD player) is input, and does not work with L.PCM and Dolby Digital 2 channel sources.
1. Press SETUP/MENU button.
~ “INPUT” appears on the display and goes into Setup Mode.
2. Press ▲▼ button to select "SURROUND", and then press the
ENTER.
3. Press ▲▼ button to select the “EX / ES”, and then press the
ENTER or ▶ button.
~ “EX/ES : AUTO” appears on the display.
4. Press ▲▼ button to set the EX/ES you want.
~ AUTO : If the unit receives an audio signal that it can
recognize, it will select an optimal decoder for playback in
6.1/7.1 channel.
If the amplifier does not recognize the audio signal, it will not
play in 6.1/7.1 channel automatically.



~ ON : Dolby Digital or DTS signal will be played in 6.1 / 7.1
channel using Dolby Digital Surround EX / DTS ES decoder.
~ OFF : Dolby Digital Surround EX / DTS ES decoder will not be used for playback.
- To exit setup mode~ Press SETUP/MENU, EXIT or RETURN button.
“SETUP OFF” appears on the display and Setup Mode is exited.
Dolby Digital - EX
Movie soundtracks encoded with Dolby Digital EX will play audio over the surround back channels also.
DTS-ES (Discrete 6.1, Matrix 6.1)
A surround back channel is added to the DTS 5.1 channel system, improving the sense of sound
directionality and space.
A built-in DTS-ES decoder has been equipped with this system that supports discs encoded with DTSES Direct and DTS-ES Matrix.
M`
You cannot use DTS-ES without surround back speakers connected.
` If the input source is in DTS 96/24, you will hear only 5.1 CH sound even if you have set EX/ES to
On.
42
HT-AS730S-XAA_0204.indd 42
2009-02-05 �� 11:47:54
EnG
SURROUND SETUP (Continued)
Setting Tone Control
This will enable you to adjust the bass and treble level.
1. Press SETUP/MENU button.
~ “INPUT” appears on the display and goes into Setup Mode.
3. Press ▲▼ button to select "TONE CONTROL", and then
press the ENTER or ▶ button.
3. Press ▲▼ button.
~ Each time you press this button, TONE SET  BASS 
TREBLE will be selected in turn.
~ If it is set to TONE: OFF, the Tone Control function will be
disabled..

● setup
2. Press ▲▼ button to select "SURROUND", and then press the
ENTER.


5. Press ▲▼ button to set the TONE CONTROL you want.
~ You can adjust it from -6 to +6dB by 1 step.
~ The sound gets smaller at -6dB and louder at +6dB.
- To exit setup mode ~ Press SETUP/MENU, EXIT or RETURN button.
“SETUP OFF” appears on the display and Setup Mode is exited.
M`
The Tone Control function can be applied to all channels except for the subwoofer.
` You can also press TEST TONE button on the remote control to use this function.
43
HT-AS730S-XAA_0204.indd 43
2009-02-05 �� 11:47:56
option setup
The Option menu enables you to make different audio settings to enhance your AV receiver experience.
1. Press SETUP/MENU button.
~ “INPUT” appears on the display and goes into Setup Mode.
2. Press ▲▼ button to select the “OPTION”, and then press the ENTER.
3. Press ▲▼ ◀▶ button to set the OPTION you want.
AV SYNC
Video may look slower than the audio if it is connected to a
digital TV. If this occurs, adjust the audio delay time to match the
video.
~ You can adjust it from 0 to 200mS in 10mS steps.


MP3 Enhancer
This also helps enhance your sound experience (ex. mp3
music). Use this if you want to hear better sound from a low
quality mp3 source.

~ On
~ Off

Smart Volume
This will regulate and stabilize the volume level against a drastic
volume change when changing channels or during a scene
transition.
~ Off
~ On


M`
To move up one level from SETUP/MENU or EXIT SETUP when the SETUP mode is released, press the RETURN
button.
44
HT-AS730S-XAA_0204.indd 44
2009-02-05 �� 11:47:57
EnG
option setup (Continued)
ASC (Auto Sound Calibration)
By setting the ASC function just once when you relocate or install the unit, you can have the unit
automatically recognize the distance between speakers, levels between channels, and frequency
characteristics to create a 7.1-channel sound field optimized for your environment.
1. Plug the ASC microphone into the ASC input jack.
. Press SETUP/MENU button.
● setup
2. Place the ASC microphone at the listening position.

. Press ▲▼ button to select the “OPTION”, and then press the
ENTER or ▶ button.
. Press ▲▼ button to select the “ASC SETUP”, and then press
the ENTER or ▶ button.

. Press the ENTER or ▶ button to select the “ASC AUTO”, and
then press the ENTER or ▶ button.
~ To create the optimal 7.1 channel sound field, the selections
are in the following sequence:
L ➞ C ➞ R ➞ SR ➞ SBR ➞ SBL ➞ SL ➞ SW
. If you see a message of "READY" on the screen, press the ENTER button to apply the
measurement value. And then unplug the ASC microphone.
ASC
Microphone
To cancel the ASC (Auto Sound Calibration) setup.
This will be automatically reverted if you press the SETUP/MENU, EXIT or RETURN button.
M`
Setting the ASC function takes about 3 minutes.
` Because the volume level of the tone is fixed during the ASC setup, you cannot adjust the volume using the
volume control buttons.
` If the auto sound microphone is disconnected during the ASC setup, the setup will be cancelled.
` When ASC measuring is done with a message of "READY" on the screen, The measurement value will not apply
until you press the ENTER button .
` To move up one level from SETUP/MENU or EXIT SETUP when the SETUP mode is released, press the RETURN
button.
` You can also press ASC button on the remote control to use this function.
45
HT-AS730S-XAA_0204.indd 45
2009-02-05 �� 11:48:00
option setup (Continued)
DRC
You can use this function to enjoy Dolby Digital sound when
watching movies at low volume at night.DRC compresses the
audio to make the loudest sounds quieter and the quietest
sounds louder.
~ Each time you press ▲▼ button, DRC : STD  DRC : MIN 
DRC : MAX will be selected in turn.
Setting DRC
~ STD : Sets DRC effect to standard.
~ MAX : Sets DRC effect to maximum.
~ MIN : Sets DRC effect to minimum.


HDMI Setup
Use this if you want to transfer audio signal using the HDMI cable.
1. HDMI Audio : AVR, TV
This preference determines whether audio received at the HDMI IN is output by the HDMI OUT. You
may want to turn this preference on if your TV is connected to the HDMI OUT and you want to listen
to the audio from a component that’s connected to an HDMI IN, through your TV’s speakers.
Normally, this should be set to Off.
- AVR : HDMI audio is not output
- TV : HDMI audio is output
. Anynet + Mode : Off, On
Anynet+ is a function that enables you to control other Samsung Devices with your Samsung TV's
remote control.
- On : Anynet + enabled.
- Off : Anynet - disabled.
. AUTO LIPSYNC : ON, OFF
The AV receiver can be set to automatically correct any delay between the video and the audio,
based on the data from the connected monitor.
- ON : HDMI lip sync enabled.
- OFF : HDMI lip sync disabled.
M`
HDMI Audio is enabled only if both of HDMI INPUT and HDMI OUT are connected properly and work normally.
` To move up one level from SETUP/MENU or EXIT SETUP when the SETUP mode is released, press the RETURN
button.
` This function works only if your HDMI-compatible TV supports HDMI Lip Sync.
46
HT-AS730S-XAA_0204.indd 46
2009-02-05 �� 11:48:01
EnG
Operation
Before using the AV receiver
Turning On/Off
● Operation
Connect the power plug to the outlet.
Press the POWER button of the remote control.
~ This unit will be turned on or set to Standby mode.
Remote control functions
You can operate your AMP (this AV receiver), TV, DVD and BD player
with this remote control.
See pages 58 ~ 60 for more details.
To select a function
Method 1
Press the Function button.
~ Each time you press this button, FM  DVD  SAT  TV  VCR 
CD  AUX  7.1 MULTI CH  IPOD will be selected in turn.
Method 2
Press DVD/BD, SAT, TV, VCR, CD, AUX, 7.1CH, IPOD or TUNER button.
~ You can directly select the desired function.
47
HT-AS730S-XAA_0204.indd 47
2009-02-05 �� 11:48:03
Selecting digital/analog Input
You can listen to sound in 2 channel analog , Dolby Digital or DTS using this unit.
Press the INPUT MODE button on the remote control to select the external device
you have connected.
~ Each time you press this button, input mode changes as follows:
For DVD/SAT function


or

For CD function

For AUX function

M

` You can also change input mode by pressing the INPUT MODE button on the front of your AV Receiver.
` You can change the detailed input setting in the “INPUT” setup. (See page 34)
` You can enjoy Dolby Digital or DTS if you connect the digital audio output jack of an external audio component to the optical
or coaxial digital audio input jack on the main unit.
48
HT-AS730S-XAA_0204.indd 48
2009-02-05 �� 11:48:11
EnG
Using the SURROUND modes
Using the NEO:6 MODE button
Press NEO:6 MODE button.~ Each time you press this button, MUSIC CINEMA will be selected in
turn.
● Operation
Using the SFE MODE button
Press SFE MODE button.
~ Each time you press this button, HALL 1 HALL 2 J.CLUB 
CHURCH  ROCK  CLASSIC  LIVE  GAME will be selected in
turn.
Using the
MODE button
Press
MODE button.
~ Each time you press this button, MOVIE  MUSIC  GAME 
MATRIX  PL will be selected in turn.
Using the
1. Press
EFFECT button
MODE button to select ‘MUSIC’ Mode.
2. Press
EFFECT button
~ Each time you press this button, C-WIDTH  DIMENSION 
PANORAMA will be selected in turn.
3. Press ▲▼ button to select Dolby Pro Logic IIx effect you want.
~ C-WIDTH : You can set from 0 to 7.
~ DIMENSION : You can set from -7 to +7.
~ PANORAMA : You can set it ON or OFF.
Using the STEREO button
Press STEREO button.
~ Outputs the sound of the selected source device in 2 CH stereo.
49
HT-AS730S-XAA_0204.indd 49
2009-02-05 �� 11:48:17
Using the SURROUND modes (Continued)
Using the SURROUND button on the front of the main unit
Selecting the NEO:6 mode
1. Press SURROUND button briefly to select “NEO:6” mode.
~ Each time you press this button, STEREO  PLIIx  NEO:6  SFE will be selected in turn.
2. Press SELECT ( .,, ) button.
~ Each time you press this button, MUSIC  CINEMA will be selected in turn.
Selecting the SFE mode
1. Press SURROUND button to select ‘SFE’ Mode.
~ Each time you press this button, STEREO  PLIIx  NEO:6  SFE will be selected in turn.
2. Press SELECT( .,, ) button.
~ Each time you press SELECT ( .,, ) button,
HALL 1HALL 2 J.CLUB  CHURCH  ROCK  CLASSIC  LIVE  GAME will be
selected in turn.
Selecting the PLIIX mode
1. Press SURROUND button to select “PLIIx” mode.
~ Each time you press this button, STEREO  PLIIx NEO:6  SFE will be selected in turn.
2. Press SELECT( .,, ) button.
~ Each time you press SELECT ( .,, ) button, MOVIE  MUSIC  GAME  MATRIX  PL will
be selected in turn.
M`
You cannot use Dolby Pro Logic llx mode for multi channel signals such as Dolby Digital and DTS.
` Pro Logic works only for PCM audio signals with sampling frequencies of 32KHz, 44KHz or
48KHz.
` Sound will not be output from the surround back speaker if the PCM audio signal is mono.
Selecting the STEREO mode
Press SURROUND button to select “STEREO” mode.
~ Each time you press this button, STEREO  PLIIx NEO:6  SFE will be selected in turn.
50
HT-AS730S-XAA_0204.indd 50
2009-02-05 �� 11:48:17
EnG
Using the SURROUND modes (Continued)
Surround Mode and Input Signal Chart
o = active, – = inactive
Input Signal
Decoding
DOLBY
(MUSIC,
CINEMA,
MATRIX,
GAME,
PRO LOGIC)
Dolby D Surr. EX
Dolby D (5.1ch)
Dolby D (2ch)
Dolby D (2ch Surr)
L.PCM (Audio)
Analog
L.PCM (Audio)
Analog
Dolby D (2ch)
Dolby D (2ch Surr)
Dolby D (2ch)
Dolby D (2ch Surr)
L.PCM (Audio)
Analog
Dolby D Surr. EX
Dolby D (5.1ch)
DTS-ES
DTS (5.1ch)
Dolby D (2ch)
Dolby D (2ch Surr)
L.PCM (Audio)
L.PCM 96KHz
Analog
Dolby Digital 5.1
Dolby Digital 5.1
Pro Logic II x
Pro Logic II x
Pro Logic II x
Pro Logic II x
Neo:6
Neo:6
Neo:6
Neo:6
DD+SFE
DD+SFE
SFE
SFE
Dolby Digital EX
Dolby Digital EX
DTS-ES
DTS-ES
Stereo
Stereo
Stereo
Stereo
Stereo
NEO:6
(MUSIC,
CINEMA)
SFE
EX/ES
STEREO
L/R
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
Output Channel
SL SBL
C
SubW
SR SBR
O
O
O
O
O
O
–
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
–
O
O
O
–
O
O
O
–
O
O
O
–
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
–
–
–
O
–
–
–
O
–
–
–
O
–
–
–
O
–
–
–
O
Display Information
Display Signal
Format
DIGITAL
DIGITAL
DIGITAL
DIGITAL
L.PCM
Analog
L.PCM
Analog
DIGITAL
DIGITAL
DIGITAL
DIGITAL
L.PCM
Analog
DIGITAL
DIGITAL
dts, ES
dts
DIGITAL
DIGITAL
L.PCM
L.PCM
Analog
Channel Status
L, C, R, SL, SR, SBL, SBR, SW
L, C, R, SL, SR, SW
L, C, R, SL, SR, SBL, SBR, SW
L, C, R, SL, SR, SBL, SBR, SW
L, C, R, SL, SR, SBL, SBR, SW
L, C, R, SL, SR, SBL, SBR, SW
L, C, R, SL, SR, SBL, SBR, SW
L, C, R, SL, SR, SBL, SBR, SW
L, C, R, SL, SR, SBL, SBR, SW
L, C, R, SL, SR, SBL, SBR, SW
L, C, R, SL, SR, SBL, SBR, SW
L, C, R, SL, SR, SBL, SBR, SW
L, C, R, SL, SR, SBL, SBR, SW
L, C, R, SL, SR, SBL, SBR, SW
L, C, R, SL, SR, SBL, SBR, SW
L, C, R, SL, SR, SBL, SBR, SW
L, C, R, SL, SR, SBL, SBR, SW
L, C, R, SL, SR, SBL, SBR, SW
L, R, SW
L, R, SW
L, R, SW
L, R, SW
L, R, SW
● Operation
Surround Mode
~ L/R : front speaker (left/right)
C : center speaker
SL/SR : surround speaker (left/right)
SBL/SBR : surround back speaker (left/right)
SW : subwoofer
M`
Channel status displays are dependent on the speaker configuration.
` SFE mode works with 2-ch signals.
51
HT-AS730S-XAA_0204.indd 51
2009-02-05 �� 11:48:18
USING THE SPEAKER ADJUSTMENT BUTTONS
Using the SPK SELECT button
1. Press SPK SELECT button to select the speaker you want.
• Each time you press this button, FRONTCEN  SURR 
S.BACK  S.W  CROVR SPK MODE OFF will be selected
in turn
2. Press ▲▼ button to set the mode (Large, Small etc.) for the selected
speaker.
• Repeat steps 1-2 to set the mode for each speaker.
Using the SPK LEVEL button
1. Press SPK LEVEL button to select the speaker you want.
• Each time you press this button, F.L  F.R CEN  S.L  S.R
 SBL  SBR  S.W SPK LVL OFF will be selected in turn.
2. Press ▲▼ button to set the speaker level you want.
• You can adjust it from -10 to +10dB by 1 step.
• The sound gets quieter at -10dB and louder at +10dB.
Using the Test Tone button
Press TEST TONE button.
• Test signal will be automatically output as follows; F.L  CEN  S.W
F.R  S.R  SBR  SBL­­­­  S.L
• During test tone output, press ▲▼ button to adjust the speaker output
level from -10 to +10 dB in 1 step increments.
52
HT-AS730S-XAA_0205.indd 52
2009-02-05 �� 3:59:38
EnG
LISTENING to the Radio
You can listen to the radio by using either automatic or manual tuning.
1. Press TUNER button.
M`
● Operation
2. Selected frequency.
~ Automatic tuning 1 :
1) Press TUNING MODE button to select PRESET.
2) Press TUNING/CH ( .,, ) button to select the preset frequency.
~ Automatic tuning 2 :
1) Press TUNING MODE button to select MANUAL
2) Press and hold TUNING/CH ( .,, ) button to automatically tune in frequency.
~ Manual tuning :
1) Press TUNING MODE button to select MANUAL.
2) Press TUNING/CH ( .,, ) button briefly to increase or decrease the frequency step by step.
You can also select FM by pressing the FUNCTION button on the front of your AV Receiver.
To Listen to mono/stereo
Press MO/ST button on the remote.
~ Each time you press this button, STEREO › MONO will be selected in turn.
~ If you select MONO in an area with weak reception, it will help to reduce noise.
~ This function works only with the Remote Control.
Presetting radio stations
You can preset up to 30 FM stations.
E.g.: Setting station FM 89.10 in preset 2.
1. Press TUNER button.
2. Press TUNING MODE button to select MANUAL and then press
TUNING/CH ( .,, ) button to select 89.10.
~ Refer to step 2 above to tune in automatically and manually.
3. Press TUNER MEMORY button.
~ Tuner number will blink on the display.


4. Press TUNING/CH ( .,, ) button to select preset 2.
~ You can select from presets 1 to 30.
5. Press TUNER MEMORY button.
~ Tuner number will disappear and station 89.10 will be saved
in preset 2.
6. To preset other stations, repeat steps 2 to 5.


To Listen to Preset Station
~ Press TUNING MODE button of the remote control to select the PRESET and press TUNING/CH
( .,, ) button.
53
HT-AS730S-XAA_0204.indd 53
2009-02-05 �� 11:48:21
Using AN iPod
You can enjoy playback of your iPod using the supplied remote control.
Listening to Music (IPOD audio function)
You can play music files stored in the iPod player by connecting it to the AV
receiver.
1. Connect the iPod dock connector to the iPod jack on the AV
Receiver.
2. Place the iPod in the Dock.
• Your iPod is automatically turned on.
3. Press the FUNCTION button on the remote control to select IPOD
mode.
• Press the FUNCTION button until IPOD AUDIO is selected
4. Press the PLAY button on the remote control to play.
• The AV receiver starts playing from the first track of the iPod player.
5. You can use the remote control or main unit to control simple playback functions such as PLAY,
PAUSE, STOP, F-SKIP(
) and B-SKIP (
).
M
See page 28 for compatible iPods.
Compatibility depends on the software version of your iPod.
This product only supports playing audio from your iPod.
54
HT-AS730S-XAA_0213.indd 54
2009-02-16 �� 2:54:19
EnG
Using AN iPod (Continued)
Watching a Movie (IPOD Video function)
You can play video files stored in the iPod player by connecting it to the
AV receiver.
● Operation
1. Connect the iPod dock connector to the iPod jack on the AV
receiver.
2. In the iPod screen, move to Videos > Settings and set the TV Out
option to On.
3. Place the iPod in the Dock.
4. Press the FUNCTION button on the remote control to select IPOD mode.
<iPod Screen>
• If the iPod player is connected to the AV receiver, each time you press the
the FUNCTION button, it will be toggled in the order of IPOD AUDIO 
IPOD VIDEO.
5. Set the AV IN option of the TV connected to the AV receiver to
COMPOSITE.
Follow the iPod onscreen guide through the following steps.
6. Press the , buttons on the remote control to select Videos and
press the ENTER button.
7. Press the , buttons on the remote control to select Movies and press
the ENTER button.
8. Press the , buttons to select the file to play and press the ENTER
button.
• Video files of the iPod player will be played on the TV screen.
9. You can use the remote control or main unit to control simple
/
playback functions such as PLAY, PAUSE, STOP, and
.
• If you press the PREV button within 3 seconds after the playback,
the player will stop playing and return to the list screen.
<iPod Screen>
If you press the PREV button 3 seconds or later after the playback, the player will move to the
start screen of the current file.
• Press the NEXT button to stop playing and return to the list screen.
• Press the RETURN button to return to the previous menu.
M
You must have the VIDEO (Monitor or VCR) output connected to your TV to view iPod video.
 See page 28 for compatible iPods.
Compatibility depends on the software version of your iPod.
 When the current file is played to the end, the next file will not be played automatically.
To play the next file, select a file to play in the list screen of the iPod player.
 No other screen than the playback one will appear on the TV screen. Check other screens on
the iPod player.
55
HT-AS730S-XAA_0213.indd 55
2009-02-16 �� 2:54:20
Convenient functions
Sleep timer function
You can set the time that this unit will shut itself off.
Press SLEEP button.
~ SLEEP : OFF  15  30  45  60  90  120 M (MIN) will be
selected in turn.
To check sleep timer
Press the SLEEP button.
~ The remaining time before this unit will shut itself off is shown on the
display.
~ Pressing the button again changes the sleep time from what you set previously.
To cancel sleep timer
~ Press SLEEP button until “SLEEP : OFF” appears on the display.
Mute function
This function is useful when answering a doorbell or telephone call.
Press the MUTE button.
~ MUTE appears on the display.
To output sound again
Press the MUTE button again.
~ MUTE will disappear and sound will output.
M`
SLEEP, Mute and the Adjust Display functions can only be operated with the remote control.
Reset function
Signal outputs and frequency response from the speaker will be adjusted
according to your speaker configuration and whether certain speakers
are used or not.
1. Press the MUTE button.
~ MUTE appears on the display.
2. Press “0” button five times and then press the ENTER button.
~ “INITIAL : NO” appears on the display.
3. Press ▲▼ buttons to select “YES”.
~ The unit will turn off after 5 seconds.
Using the SELECT button
1. Turn off the power and hold the SELECT ( .,, ) button for longer than 5 seconds.
~ POWER STANDBY indicator will flash.
M`
Using the RESET function will erase all stored settings.
` Do not use this unless necessary.
56
HT-AS730S-XAA_0205.indd 56
2009-02-05 �� 3:59:59
EnG
Convenient functions (Continued)
Adjust the display
You can adjust the brightness of the display.
Press the DIMMER button.
~ Each time you press this, the brightness changes as follows : DARK 
BRIGHT.
● Operation
Using headphones
Use headphones (not supplied) for private listening pleasure.
Connect the headphones to the headphone jack and listen to music.
M`
Do not turn the volume up too high when you use headphones as It may damage your hearing.
57
HT-AS730S-XAA_0204.indd 57
2009-02-05 �� 11:48:24
Miscellaneous
Operating your TV with the remote control
1. Press POWER button to turn on the TV.
2. Press TV button to set the remote to TV mode.
3. Point the remote control toward the TV.
4. While holding down POWER button, enter the code corresponding to your brand of TV.
~ If there is more than one code listed for your TV in the table, enter one at a time to determine
which code works.
~ If the code matches the TV's code, the TV will be turned off.
5. If TV is turned on or off when you press the power button of the remote control, the setting is
completed.
~ You can use the TV POWER, VOLUME, CHANNEL, MENU and Numeric buttons (0~9).
M`
The remote control may not work on some brands of TVs. Also, some operations may not be
possible depending on your brand of TV.
` The remote control will work with Samsung TVs by default.
58
HT-AS730S-XAA_0204.indd 58
2009-02-05 �� 11:48:24
EnG
Operating your TV with the remote control (Continued)
TV Brand Code List
Brand
Code Number
Brand
Luxman
LXI (Sears)
AOC
Bell & Howell
(M.Wards)
Brocsonic
Candle
Cetronic
Citizen
CINEMA
Classic
Concerto
Contec
Coronado
Craig
001, 018, 040, 048
057, 058, 081
059, 060
018
003
003, 018, 025
097
003
018
046
015
003, 005, 061, 082, 083,
084
062
003
059, 061, 063
003
002, 003, 004, 015,016,
017, 018, 019, 020, 021,
022, 023, 024, 025, 026,
027, 028, 029, 030, 032,
034, 035, 036, 040, 048,
059, 090, 099, 100
040
003
003, 015, 040, 046, 059,
061, 064, 082, 083, 084,
085
019, 065, 103
003
003
006, 040, 056, 059, 066,
067, 068
040
015, 018, 050, 059, 069
045
056, 059, 067, 086
070
059, 061, 087, 088
Croslex
Crown
CURTIS MATHES
CXC
Daewoo
Daytron
Dynasty
Emerson
Fisher
Funai
Futuretech
General Electric
(GE)
Hall Mark
Hitachi
Inkel
JC Penny
JVC
KTV
KEC
KMC
LG (Goldstar)
003, 015, 040
015
001, 015, 016, 017, 037,
038, 039, 040, 041, 042,
043, 044, 054, 086
Code Number
Brand
Code Number
018
019, 054, 056, 059, 060,
062, 063, 065, 071
015, 017, 018, 048, 054,
059, 060, 062, 072, 089
Sylvania
Symphonic
Tatung
Techwood
018, 040, 048, 054, 059,
060, 062
061, 095, 096
006
018
Marantz
Matsui
040, 054
054
Teknika
TMK
003, 015, 018, 025
018, 040
MGA
Mitsubishi/MGA
018, 040
018, 040, 054, 059, 060,
­075, 101
018
018, 019, 020, 040, 059,
060
003
003
003
006, 007, 008, 009, 054,
066, 067, 073, 074
018
003, 015, 017, 018, 048,
054, 059, 062, 069, 090
015, 017, 018, 040, 048
054, 062, 072, 112, 114,
117, 118
063, 066, 080, 091
015, 018, 059
040
006, 066, 067
017, 048, 056, 060, 061,
075
018, 059, 067, 076, 077,
078, 092, 093, 094
003, 019
040
000, 015, 016, 017, 040,
043, 046, 047, 048, 049,
054, 059, 060, 098
019, 061, 065, 101, 102,
103, 104
003, 040, 060, 061
015, 018, 019
015, 057, 064, 101, 105,
106, 115
057, 058
Toshiba
019, 057, 063, 071, 101
107, 109, 110, 111, 113
018
059, 060, 069
015, 017, 018, 040, 048,
054, 060, 064
018
040
003
058, 079
001
003, 054
054
054, 109, 114
054
054, 114
054, 112, 114
054, 112
054
103
108, 109, 113, 119, 120,
121
108
108
113
113
113
114
114
114
114
114
114
114
114
114
116
Magnavox
MTC
NEC
Nikei
Onking
Onwa
Panasonic
Penney
Philco
Philips
Pioneer
Portland
Proton
QUASAR
Radio Shack
RCA/Proscan
Realistic
Sampo
Samsung
Sanyo
Scott
Sears
Sharp
Signature 2000
(M.Wards)
Sony
Soundesign
Spectricon
SSS
Vidtech
Videch
Wards
Yamaha
York
Yupiteru
Zenith
Zonda
Dongyang
LOWE
FINLUX
YOKO
LOEWE OPTA
PHONOLA
RADIOLA
SCHNEIDER
AKAI
GRUNDIG
BLAUPUNKT
SIEMENS
CGE
IMPERIAL
MIVAR
SABA
BANG&OLUFSEN
BRIONVEGA
FORMENTI
METZ
WEGA
RADIOMARELLI
SINGER
SINUDYNE
TELEFUNKEN
● MISCELLANEOUS
Admiral (M.Wards) 056, 057, 058
A Mark
001, 015
Anam
001, 002, 003, 004,005,
006, 007, 008, 009, 010,
011, 012, 013, 014
050, 051, 052, 053, 055,
101
003, 040
001
018
59
HT-AS730S-XAA_0204.indd 59
2009-02-05 �� 11:48:25
Operating your DVD or BD player with the remote control
1. Press POWER button to turn on the DVD (BD) player.
2. Press DVD (BD) button to set the remote to DVD (BD) mode.
~ If you operate VCR, press VCR button to set the remote to VCR mode.
3. Point the remote control toward the DVD (BD).
4. While holding down POWER button, enter the code corresponding to your brand of DVD (BD).
~ If there is more than one code listed for your DVD (BD) in the table, enter one at a time to
determine which code works.
~ If the code matches the DVD (BD)'s code, the DVD (BD) will be turned off.
5. If DVD (VCR) is turned on or off when you press the power button of the remote controller, the
setting is completed.
~ You can use DVD (BD) POWER, VOLUME, PLAY, PAUSE, STOP, SKIP, MENU and Numeric
button (0~9).
M`
The remote control may not work on some brands of DVD (BD).
Also, some operations may not be possible depending on your brand of DVD (BD).
` The remote control will work with Samsung DVD (BD) by default.
DVD Brand Code List
Brand
DENON
DOONOON
DMTECH
FISHER
GE
HARMAN/KARDON
JVC
KENWOOD
LG
MAGNAVOX
MITSUBISHI
Code Number
003, 032
019
017
002
006
012
010, 013
008
001
004
005, 016
Brand
ONKYO
OPTIMUS
PANASONIC
PROSCAN
PHILIPS
PIONEER
RCA
SAMSUNG
SANYO
SONY
THETA DIGITAL
Code Number
004, 014
011
021
006
004, 023
007, 011, 022, 025
006
000, 027
002
015, 020
011
Brand
TOSHIBA
YAMAHA
ZENITH
TAEGWANG
PS2
X-BOX
APEX
Marantz
Code Number
004, 018
009, 033
004, 024
026
028
029
030
031
BD player Brand Code List
Brand
SAMSUNG
M
Code Number
000, 001, 002, 003, 004
` For the BD player, only a Samsung product can be controlled with the remote control.
60
HT-AS730S-XAA_0204.indd 60
2009-02-05 �� 11:48:25
EnG
Troubleshooting
Before requesting service, please check the following.
Symptom
Check
Remedy
• Is the power cord plugged into the
outlet?
• Connect the power plug to the outlet.
A function does not work
when the button is pressed.
• Is there static electricity in the air?
• Disconnect the power plug and connect
it again.
Sound is not produced.
• A re the speakers and external
components connected properly?
• Is the Mute function on?
• Is the volume set to minimum?
• Is the speaker setup set incorrectly to
NONE?
• Connect them correctly.
• Press Mute button to cancel the
function.
• Adjust the volume.
• Refer to pages 35 to select LARGE,
SMALL or YES.
Picture does not appear on a
TV when the function is
selected.
• Is the external component connected
properly?
Remote controller does not
work.
• Are the batteries drained?
• Is the distance between remote control
and main unit too great?
• Replace with new batteries.
• Operate at close distance.
The sound from the left/right
channels is reversed.
• A
re the left/right speaker or left/right
• C heck the left/right channel and connect it/
them correctly.
Can't receive radio
broadcasts.
• Is FM antenna connected properly?
• Connect the antenna correctly.
• If the input strength of antenna signal is
weak, install the FM antenna in a place
with good reception.
There is no sound from
surround speakers.
• Is the surround speaker connected
properly?
• Is SURR (surround) incorrectly set to
NONE in speaker setup?
• Is surround mode set to stereo?
• R efer to pages 16 ~18 to connect them
properly.
input/output cables connected
properly?
● troubleshooting
The unit will not turn on.
• Connect it correctly.
• Refer to page 35 to select LARGE or SMALL.
• R efer to pages 39 ~ 43 to select proper
Surround Mode.
61
HT-AS730S-XAA_0204.indd 61
2009-02-05 �� 11:48:25
Symptom
There is no sound from
surround back speakers
Check
• Are the surround back speakers
connected properly?
• Is the S.BACK(Surround Back) selected
to NONE in Speaker Setup?
• Is Surround Mode set to EX/ES?
Remedy
• Refer to pages 16 ~18 to connect it
properly.
• Refer to page 35 to select LARGE or
SMALL.
• Refer to page 42 to set Surround Mode
to EX/ES.
Can't select EX/ES mode.
• Is S.BACK(Surround Back) selected to
NONE in Speaker Setup?
• Is the input signal selected properly?
• Refer to page 35 to select LARGE or
SMALL.
• Use 7.1 channel external component.
Can't select Dolby Pro Logic
llx mode.
• Is the input signal selected properly?
• Select 2 channel Dolby Digital, PCM,
and Analog input signal.
Can't select NEO:6 mode.
• Is the input signal selected properly?
• Use PCM and Analog input signal.
There is no sound when
playing a DTS encoded DVD.
• Is Digital input selected?
• C heck whether the DVD player is
properly connected and refer to page
48 to select the digital input.
Product protection function
Heat protection
•T
he protection function will come on if the main unit or power transformer overheats.
"
" will appear in the display .
This function will come on :
- If speaker terminal is shorted
- If speaker cable is shorted
If there is no problem when you turn the unit on again after turning it off, PROTECTION mark will disappear on the
display and the unit will work properly.
M`
If PROTECTION appears on the display, check whether the speaker terminal is shorted and
then turn on the unit
62
HT-AS730S-XAA_0204.indd 62
2009-02-05 �� 11:48:25
EnG
Appendix
Specifications
120V, 60 Hz
Standby power consumption
0.9W
Power consumption
GENERAL
FM TUNER
AMPLIFIER
FREQUENCY
RESPONSE
HDMI
VIDEO OUTPUT
Main unit
75W
Subwoofer
90W
Weight
12.7 Ibs
Dimensions (W x H x D)
16.9 x 5.7 x 13.7 inches
Operating temperature range
41°F~+95°F
Operating humidity range
10%~75%
Frequency response
87.5~108.0MHz
Usable sensitivity
12dBf
S/N ratio
MONO/STEREO 55/55dB
Distortion
MONO/STEREO 0.3/0.8%
Stereo separation
30dB
Tuner output level
1kHz, 75kHz Dev
Rated output
20Hz~20kHz/THD = 0.9%
Front speaker(left+right)
4 Ω 100W/CH
Center speaker
4 Ω 100W/CH
Surround speaker(left+right)
4 Ω 100W/CH
Surround back
4 Ω 100W/CH
Input sensitivity/impedance
450mV/47kΩ
S/N ratio (analog input)
80dB
Separation (1kHz)
60dB
Analog input
20Hz~20kHz(±3dB)
Digital input/96kHz PCM
20Hz ~44kHz(±3dB)
Input
Compatible 1080p
Output
Compatible 1080p
TV format
NTSC/PAL
Input level/impedance
1Vp-p/75 Ω
Output level/impedance
1Vp-p/75 Ω
Video frequency response
5Hz to 10kHz(-3dB)
S/N ratio
60dB
● appendix
Power supply
* S/N ratio, distortion, separation and usable sensitivity are based on measurement using AES (Audio Engineering
Society) guidelines.
63
HT-AS730S-XAA_0205.indd 63
2009-02-05 �� 4:02:27
SAMSUNG AV receiver
LIMITED WARRANTY TO ORIGINAL PURCHASER
This SAMSUNG brand product, as supplied and distributed by Samsung Electronics America, Inc. (SAMSUNG) and delivered new, in
the original carton to the original consumer purchaser, is warranted by SAMSUNG against manufacturing defects in materials and
workmanship for a limited warranty period of:
One (1) Year Parts and Labor*
(*90 days Parts and Labor for Commercial Use)
This limited warranty begins on the original date of purchase, and is valid only on products purchased and used in the United States.
To receive warranty service, the purchaser must contact SAMSUNG for problem determination and service procedures. Warranty
service can only be performed by a SAMSUNG authorized service center. The original dated bill of sale must be presented upon
request as proof of purchase to SAMSUNG or SAMSUNG's authorized service center. Transportation of the product to and from the
service center is the responsibility of the purchaser.
SAMSUNG will repair or replace this product, at our option and at no charge as stipulated herein, with new or reconditioned parts or
products if found to be defective during the limited warranty period specified above. All replaced parts and products become the
property of SAMSUNG and must be returned to SAMSUNG. Replacement parts and products assume the remaining original
warranty, or ninety (90) days, whichever is longer.
SAMSUNG's obligations with respect to software products distributed by SAMSUNG under the SAMSUNG brand name are set
forth in the applicable end user license agreement. Non-SAMSUNG hardware and software products, if provided, are on an
“AS IS” basis. Non-SAMSUNG manufacturers, suppliers, publishers, and service providers may provide their own warranties.
This limited warranty covers manufacturing defects in materials and workmanship encountered in normal, and except to the extent
otherwise expressly provided for in this statement, noncommercial use of this product, and shall not apply to the following, including,
but not limited to: damage which occurs in shipment; delivery and installation; applications and uses for which this product was not
intended; altered product or serial numbers; cosmetic damage or exterior finish; accidents, abuse, neglect, fire, water, lightning or
other acts of nature; use of products, equipment, systems, utilities, services, parts, supplies, accessories, applications, installations,
repairs, external wiring or connectors not supplied and authorized by SAMSUNG, or which damage this product or result in service
problems; incorrect electrical line voltage, fluctuations and surges; customer adjustments and failure to follow operating instructions,
cleaning, maintenance and environmental instructions that are covered and prescribed in the instruction book; product removal or
reinstallation; reception problems and distortion related to noise, echo, interference or other signal transmission and delivery
problems. SAMSUNG does not warrant uninterrupted or error-free operation of the product.
THERE ARE NO EXPRESS WARRANTIES OTHER THAN THOSE LISTED AND DESCRIBED ABOVE, AND NO WARRANTIES
WHETHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTIES OF MERCHANTABILITY
OR FITNESS FOR A PARTICULAR PURPOSE, SHALL APPLY AFTER THE EXPRESS WARRANTY PERIODS STATED ABOVE,
AND NO OTHER EXPRESS WARRANTY OR GUARANTY GIVEN BY ANY PERSON, FIRM OR CORPORATION WITH RESPECT
TO THIS PRODUCT SHALL BE BINDING ON SAMSUNG. SAMSUNG SHALL NOT BE LIABLE FOR LOSS OF REVENUE OR
PROFITS, FAILURE TO REALIZE SAVINGS OR OTHER BENEFITS, OR ANY OTHER SPECIAL, INCIDENTAL OR
CONSEQUENTIAL DAMAGES CAUSED BY THE USE, MISUSE OR INABILITY TO USE THIS PRODUCT, REGARDLESS OF THE
LEGAL THEORY ON WHICH THE CLAIM IS BASED, AND EVEN IF SAMSUNG HAS BEEN ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES. NOR SHALL RECOVERY OF ANY KIND AGAINST SAMSUNG BE GREATER IN AMOUNT THAN THE
PURCHASE PRICE OF THE PRODUCT SOLD BY SAMSUNG AND CAUSING THE ALLEGED DAMAGE. WITHOUT LIMITING THE
FOREGOING, PURCHASER ASSUMES ALL RISK AND LIABILITY FOR LOSS, DAMAGE OR INJURY TO PURCHASER AND
PURCHASER°ØS PROPERTY AND TO OTHERS AND THEIR PROPERTY ARISING OUT OF THE USE, MISUSE OR INABILITY
TO USE THIS PRODUCT SOLD BY SAMSUNG NOT CAUSED DIRECTLY BY THE NEGLIGENCE OF SAMSUNG. THIS LIMITED
WARRANTY SHALL NOT EXTEND TO ANYONE OTHER THAN THE ORIGINAL PURCHASER OF THIS PRODUCT, IS
NONTRANSFERABLE AND STATES YOUR EXCLUSIVE REMEDY.
Some states do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of incidental or
consequential damages, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights,
and you may also have other rights which vary from state to state.
To obtain warranty hardware service, please contact SAMSUNG at:
Samsung Electronics America, Inc.
105 Challenger Road Ridgefield Park, NJ07660-0511
1-800-SAMSUNG(726-7864) and www.samsung.com
HT-AS730S-XAA_0204.indd 64
2009-02-05 �� 11:48:26
Contact SAMSUNG WORLD WIDE
If you have any questions or comments relating to Samsung products, please contact the SAMSUNG
customer care center.
Region
North America
Latin America
Europe
CIS
Asia Pacific
Country
HT-AS730S-XAA_0204.indd 65
Web Site
1-800-SAMSUNG(726-7864)
01-800-SAMSUNG(726-7864)
1-800-SAMSUNG(726-7864)
0800-333-3733
0800-124-421, 4004-0000
800-SAMSUNG(726-7864)
00-1800-5077267
800-7919267
0-800-507-7267
1-800-10-7267
800-6225
1-800-299-0013
1-800-234-7267
800-7267
1-800-682-3180
1-800-751-2676
1-800-SAMSUNG(726-7864)
0-800-100-5303
01-8000112112
BELGIUM
02 201 2418
CZECH REPUBLIC
DENMARK
800-SAMSUNG(800-726786)
8-SAMSUNG(7267864)
www.samsung.com/ca
www.samsung.com/mx
www.samsung.com/us
www.samsung.com/ar
www.samsung.com/br
www.samsung.com/cl
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com.co
www.samsung.com/be (Dutch)
www.samsung.com/be_fr (French)
www.samsung.com/cz
www.samsung.com/dk
FINLAND
30-6227 515
www.samsung.com/fi
FRANCE
3260 dites ‘SAMSUNG’(€ 0,15/Min)
0825 08 65 65 (€ 0,15/Min)
www.samsung.com/fr
GERMANY
HUNGARY
ITALIA
LUXEMBURG
NETHERLANDS
NORWAY
POLAND
PORTUGAL
SLOVAKIA
SPAIN
SWEDEN
U.K
EIRE
AUSTRIA
SWITZERLAND
RUSSIA
KAZAKHSTAN
UZBEKISTAN
KYRGYZSTAN
TADJIKISTAN
UKRAINE
LITHUANIA
LATVIA
ESTONIA
AUSTRALIA
NEW ZEALAND
CHINA
HONG KONG
INDIA
INDONESIA
JAPAN
MALAYSIA
www.samsung.de
www.samsung.com/hu
www.samsung.com/it
www.samsung.com/lu
www.samsung.com/nl
www.samsung.com/no
www.samsung.com/pl
www.samsung.com/pt
www.samsung.com/sk
www.samsung.com/es
www.samsung.com/se
www.samsung.com/uk
www.samsung.com/ie
www.samsung.com/at
www.samsung.com/ch
www.samsung.ru
www.samsung.com/kz_ru
www.samsung.com/kz_ru
SINGAPORE
THAILAND
TAIWAN
VIETNAM
TURKEY
01805 - SAMSUNG(726-7864 € 0,14/Min)
06-80-SAMSUNG(726-7864)
800-SAMSUNG(726-7864)
02 261 03 710
0900-SAMSUNG (0900-7267864) (€ 0,10/Min)
3-SAMSUNG(7267864)
0 801 1SAMSUNG(172678), 022-607-93-33
80820-SAMSUNG(726-7864)
0800-SAMSUNG(726-7864)
902-1-SAMSUNG (902 172 678)
075-SAMSUNG(726 78 64)
0845 SAMSUNG (7267864)
0818 717 100
0810-SAMSUNG(7267864, € 0.07/min)
0848-SAMSUNG(7267864, CHF 0.08/min)
8-800-555-55-55
8-10-800-500-55-500
8-10-800-500-55-500
00-800-500-55-500
8-10-800-500-55-500
8-800-502-0000
8-800-77777
8000-7267
800-7267
1300 362 603
0800 SAMSUNG (0800 726 786)
800-810-5858, 400-810-5858, 010-6475 1880
3698-4698
3030 8282, 1800 110011, 1-800-3000-8282
0800-112-8888
0120-327-527
1800-88-9999
1-800-10-SAMSUNG(726-7864)
1-800-3-SAMSUNG(726-7864), 02-5805777
1800-SAMSUNG(726-7864)
1800-29-3232, 02-689-3232
0800-329-999
1 800 588 889
444 77 11
SOUTH AFRICA
0860-SAMSUNG(726-7864 )
www.samsung.com/za
U.A.E
800-SAMSUNG (726-7864), 8000-4726
www.samsung.com/ae
PHILIPPINES
Middle East &
Africa
Customer Care Center 
CANADA
MEXICO
U.S.A
ARGENTINE
BRAZIL
CHILE
NICARAGUA
HONDURAS
COSTA RICA
ECUADOR
EL SALVADOR
GUATEMALA
JAMAICA
PANAMA
PUERTO RICO
REP. DOMINICA
TRINIDAD & TOBAGO
VENEZUELA
COLOMBIA
www.samsung.ua
www.samsung.com/lt
www.samsung.com/lv
www.samsung.com/ee
www.samsung.com/au
www.samsung.com/nz
www.samsung.com/cn
www.samsung.com/hk
www.samsung.com/in
www.samsung.com/id
www.samsung.com/jp
www.samsung.com/my
www.samsung.com/ph
www.samsung.com/sg
www.samsung.com/th
www.samsung.com/tw
www.samsung.com/vn
www.samsung.com/tr
2009-02-05 �� 11:48:26
QUESTIONS OR COMMENTS?
COUNTRY
CALL
OR VISIT US ONLINE AT
WRITE
IN THE US
1-800-SAMSUNG
(7267864)
www.samsung.com/us
Samsung Electronics America, Inc.
105 Challenger Road Ridgefield Park,
NJ 07660-0511
Code No. AH68-02174R
HT-AS730S-XAA_0204.indd 66
2009-02-05 �� 11:48:27
Download PDF

advertising