think SAFETY... think HUBBELLSAFE HUBBELL

think SAFETY... think HUBBELLSAFE HUBBELL
®
HUBBELL
Safety Product Guide
think SAFETY...
think HUBBELLSAFE
Hubbell Safety Product Guide
Table of Contents
Hubbell Safe . ........................................................................ 3
Watertight Wiring Devices............................................ 4-5
Watertight Safety-Shroud® Twist-Lock®; Watertight Devices;
IEC Pin & Sleeve; UL/CSA Enclosure Type 4X Box
Watertight Wiring Devices
Ground Fault Circuit Interrupters.............................. 6-7
Receptacles; Portables; Sensing Modules; Circuit Testers
Temporary Power............................................................. 8-9
SPIDER® II Temporary Power Boxes; Portable Outlet Boxes;
LINKOSITY®
Motor Control
Motor Control................................................................. 10-11
Circuit-Lock® Unfused and Fused Disconnect Switches;
Manual Motor Controllers; MotorQuick®
Wire Management........................................................ 12-13
Kellems® Strain Relief; Kellems® Support Grips;
PolyTuff® Non-Metallic Liquidtight Conduit and Tubing
Arc Flash Safety................................................................. 14
ARC Flash Protection
Panel-Safe™; Mechanical Interlocks
Lockout, Tagout. ................................................................ 15
PLUGOUT®; SWITCHOUT®; Locking Switches
Cable Protection................................................................ 16
Industrial and Commercial Cord Reels
Hose and Cable Protection Systems........................ 17
Lockout Tagout
TrukTrak®, TredTrak® and AccessTrak®
Specialty Devices......................................................... 18-19
HBL5262 Series Receptacles; Tamper-Resistant and
Water Resistant Duplex Receptacles; Corrosion Resistant Devices;
Weatherproof Covers
Cable Protection
2
www.hubbell-wiring.com
Safety First with Hubbell
The safety of people and equipment matter most
Too costly to ignore
Hubbell believes that every employee in every business has the right to a safe working environment.
Not only is safety the key to allowing people to be confident and secure in their jobs, it is also critical to
enhancing productivity, reducing downtime and avoiding significant accident expenses—all of which leads
to sustainability and a lower Total Cost of Ownership (TCO).
Ensuring safety everywhere
Potential safety hazards exist in almost every workplace environment—from open office areas and factory
floors, to construction sites and retail spaces. That’s why all
employers are required to comply with strict safety codes and
regulations. Many businesses pride themselves on the number of
accident-free days, which is achieved through established formal
safety programs that include training, ongoing safety evaluations
and documentation.
Hubbell Wiring Systems is committed to helping
our customers maintain a safe workplace
environment. Since introducing the first safety
receptacle that set the industry standard,
Hubbell has always been focused on safety. That’s why Hubbell products are designed
and developed to first provide maximum safety against injury and the potential dangers
of electricity.
• Hubbell Twist-Lock® plugs and receptacles ensure mating only with the correct
voltage and amperage.
• Hubbell’s full line of watertight devices provides protection against electrical shock
in wet environments.
• All Hubbell ground fault receptacles and temporary power distribution systems
provide a high level of personnel protection.
• Hubbell Circuit-Lock® disconnects and MotorQuick® motor controllers enable safe
control and disconnection of power in the industrial environment
• Lockout-tagout features and devices offer a means to protect employees by
avoiding unintentional energizing of equipment during diagnostics or repair.
• Hubbell wire management and hose and cable protection systems safeguard
cables and cords, ultimately protecting people by preventing damaged circuits and
minimizing trip hazards.
An essential core value
As an industry leader, Hubbell is extremely involved with regulatory associations and has an extensive
knowledge of codes and regulations that businesses must comply with to ensure safety and reduce
risk. From the latest version of the National Electric Code® (NEC) to NEMA requirements and OSHA
regulations, Hubbell products comply with the latest codes to help our customers ensure proper safety
in the workplace. As part of our ongoing commitment to safety, Hubbell holds numerous ShopTalk™
Seminars across the nation to provide up-to-date information on safety requirements, potential safety
risks and products and solutions.
Hubbell understands the importance of making safety a core value in every business and the cost of
non-compliance. Keeping people and equipment safe with Hubbell products reduces risk and liability.
Think safety.
Think Hubbell.
NEC® is a registered trademark of the
National Fire Protection Association (NFPA).
www.hubbell-wiring.com
3
Connections for Wet and Damp Locations
Watertight Devices
When it comes to safety, most everyone knows that water and electricity can create a dangerous
environment. From harsh factory and construction sites to laboratories and outdoor applications,
ensuring a watertight seal for electrical devices is critical to ensuring maximum safety of personnel in
any wet environment. Hubbell Watertight Twist-Lock® devices have become the industry standard
for maintaining a watertight seal when in use and when disconnected as well as preventing
unintentional disconnects.
Watertight Safety-Shroud® Twist-Lock®
• Maintains UL/CSA Enclosure Type 4X
watertight seal when in use and when
disconnected
• Constructed from engineered high impact
thermoplastic for heavy-duty industrial
applications
• Shroud meets or exceeds California OSHA
2510.7(6) electrical safety requirement for
"skirted plugs" Title 8 Division 1 Chapter 4
Watertight Devices
• Double insulated elastomeric cover and
NEMA IEC Enclosure
Enclosure Classification
Type No. Designation Basic Description
3R
IP14
Rainproof and Sleet (Ice)
Resistant- Outdoor
4
IP56
Watertight and DusttightIndoor and Outdoor
4X
IP56
Watertight, Dusttight and
Corrosion-Resistant Indoor and Outdoor
6
IP67
Watertight, Dusttight
and Sleet (Ice) ResistantIndoor and Outdoor
12
IP52
Industrial Use, Dusttight
and Driptight- Indoor
thermoplastic body for extra safety and water
resistance
• Exclusive triple by-pass sealing system
• Corrosion-resistant nickel plated blades and
stainless steel captive assembly screws
• NEMA 4, 4X, 6, 6P, IP65, IP66, IP67
Ordering Information
Watertight Locking Devices
NEMA Rating
Color Coded by Voltage
15A
125V
15A
277V AC
20A
125V
20A
250V
20A
277V AC
20A
3Ø 250V
30A
3Ø 250V AC
30A
3Ø 480V AC
4
W
G
Poles/
Wires
Plug
Watertight Safety-Shroud®
Connector
Receptacle
Plug
Watertight
Connector Receptacle
L5-15 2P/3W
—
—
—
24W47H 25W47H 65W47H
L7-15 2P/3W
—
—
—
24W34H 25W34H 65W34H
15A 125V
NEMA L5-15P
UL/CSA
0.5 HP
W
G
15A 277V AC
NEMA L7-15P
UL/CSA
2 HP
W
G
L5-20 2P/3W HBL2311SW HBL2313SW HBL2310SW 26W47H 27W47H 67W47H
20A 125V
NEMA L5-20P
UL/CSA
1 HP
X
G
Y
L6-20 2P/3W HBL2321SW HBL2323SW HBL2320SW 26W48H 27W48H 67W48H
20A 250V
NEMA L6-20P
UL/CSA
2 HP
L7-20 2P/3W HBL2331SW HBL2333SW HBL2330SW 26W49H 27W49H 67W49H
30A 277V AC
NEMA L7-30P
UL/CSA
3 HP
X
Y
G
L15-20 3P/4W HBL2421SW HBL2423SW HBL2420SW 26W75H 27W75H 67W75H
Z
20A 3Ø 250V AC
NEMA L15-20P
UL/CSA
3 HP
X
Y
G
L15-30 3P/4W HBL2721SW HBL2723SW HBL2720SW 28W75H 29W75H 69W75H
Z
30A 3Ø 250V AC
NEMA L15-30P
UL/CSA
3 HP
X
Y
G
L16-30 3P/4W HBL2731SW HBL2733SW HBL2730SW 28W76H 29W76H 69W76H
Z
30A 3Ø 480V AC
NEMA L16-30P
UL/CSA
10 HP
For complete listing of Hubbell Products see our full line catalog.
www.hubbell-wiring.com
Maximum Protection for Electrical Connections
Watertight Devices
For food processing and waste water applications, Hubbell Watertight IEC Pin & Sleeve devices
ensure watertight performance while protecting users with a super tough, non-conductive housing
and shrouded contact pins. The opening on the plug shroud accommodates lockout/tagout locks
for maximum safety while the UL Enclosure Type 4X Box offers a variety of watertight connections
and provides maximum safety for use with Straight Blade and Twist-Lock® devices.
IEC Pin & Sleeve
• Superior construction and engineered materials for
maximum durability
• Sequential contact engagement ensures the ground
mates first and breaks last
• Thermoset polyester interiors provide unsurpassed
ability to withstand high amounts of heat which may
result from overload or arching
UL Enclosure Type 4X Box
• One step self-latching, spring loaded gasketed
cover for maintaining maximum reliability and
protection when not in use
• Corrosion, impact and chemical resistant
Valox® enclosure
• Available in common NEMA configurations,
pre-wired for installation simplicity
NEC® 110.11 (Electrical Installations)
Unless identified for use in the operating
environment, no conductors or
equipment shall be located in damp or
wet locations.
Ordering Information
IEC Watertight
Pin & Sleeve
Rating Color Coded
by Voltage
20A
3Ø 480V
30A
3Ø 250V
30A
3Ø 480V
30A
3Ø 600V
30A
3ØY 277/480V
60A
250V
60A
3ØY 120/208V
60A
3Ø 480V
60A
3Ø 600V
100A
250V
100A
3ØY 120/208V
100A
3Ø 480V
100A
3Ø 600V
Conduit Feed
UL Type 4X Rated
Poles/
Wires
Plug, Connector
and Receptacle
3P 4W
HBL420x7W
3P 4W
HBL430x9W
3P 4W
HBL430x7W
3P 4W
HBL430x5W
Straight Blade
Rating
Catalog Numbers
20A 125V
MCWF2010*
Watertight Safety-Shroud® Twist-Lock®
Rating
Catalog Numbers
20A 125V
MCWF2020
20A 250V
MCWF2030
20A 277V
MCWF2040
20A 125/250V
MCWF2070
4P 5W
HBL530x7W
3P 4W
HBL460x9W
20A 3Ø 250V
MCWF2080
HBL560x9W
20A 3Ø 480V
MCWF2090
30A 125V
MCWF2050
4P 5W
3P 4W
HBL460x7W
30A 250V
MCWF2060
3P 4W
HBL460x5W
30A 125/250V
MCWF2100
3P 4W
HBL4100x9W
30A 3Ø 250V
MCWF2110
30A 3Ø 480V
MCWF2120
30A 3Ø 600V
MCWF2130
4P 5W
NEC® 300.6(D) (Indoor Wet Locations)
For indoor wet locations where walls are
frequently washed or where there are
surfaces of absorbent materials, such as
wood, the wiring system where exposed,
including boxes, fittings, raceway and
cable shall be mounted so that there is at
least 1/4 inch (6mm) airspace between it
and the wall or supporting surface.
HBL5100x9W
3P 4W
HBL4100x7W
3P 4W
HBL4100x5W
* Type 4X Rating with cover closed
Valox® is a registered trademark of SABIC Innovative
Plastics acquired from GE.
x= device: P (Plug), C (Connector), and R (Receptacle)
www.hubbell-wiring.com
For complete listing of Hubbell Products see our full line catalog.
5
Personnel Protection and Safety
Ground Fault Circuit Interrupters (GFCIs)
Required by code, receptacles in any wet area must all be protected with ground fault circuit
interrupters (GFCIs) that stop the flow of electric current to protect people in the presence of
a ground fault. Hubbell offers AUTOGUARD™ and standard heavy duty GFCI receptacles.
AUTOGUARD™ is a self-test version that continually tests electronic circuitry automatically.
The AUTOGUARD™ unit features a green LED to indicate “power-on” and a red LED that is
both a “trip indicator” when solid, and an “end of life indicator” when flashing.
The GFCI sensing modules work in conjunction with hydraulic magnetic circuit breakers to
interrupt power in the event of a ground fault condition.
Extra Heavy Duty GFCI Receptacles
• Patented tamper-resistant design limits improper
access to energized contacts
• Heavy duty brass bridge to withstand abuse
• Self-Test units continually tests and monitors for
protection automatically
• No power at device face if reverse wired, eliminating
false assumption of protection
• 10 kA Short Circuit Current Rating
Sensing Modules
For non-residential installations all 125V
15 and 20 AMP receptacles installed in
locations specified in NEC® Article
210.8(B)(1)FR-(8) shall have ground
fault circuit interrupter protection for
personnel. These areas include:
• Monitors electrical circuit with no direct load present
(1) Bathrooms
(2) Kitchens
(3) Roof Tops
(4) Outdoors
(5) Sinks (within 6’ of edge)
(6) Indoor Wet Locations
(7) Locker Rooms / Shower Facilities
(8) Garages / Service Bays
• Enclosure Type 4X rating
at the module
• Hydraulic breakers available from 1 to 50 AMP
meets
• 120 and 240 volt modules available in automatic or
manual “safe start” reset versions
• UL 1053 Compliant
Ordering Information
GFCI Sensing Module
50A Maximum Extra Heavy Duty
GFCI Receptacles
NEMA
Rating Color
Tamper-Resistant/Weather Resistant
AUTOGUARD™
Self Test
Circuit Guard®
15A Brown GFR5262SG
GFR5262TR
125V Other GFR5262SGxx GFR5262xxTR
15A 125V
NEMA 5-15R
20A Brown GFR5362SG
GFR5362TR
125V Other GFR5362SGxx GFR5362xxTR
20A 125V
NEMA 5-20R
x=color: BK (Black), GY (Gray), I (Ivory), R (Red) and W (White)
Description
Catalog Number
120V AC Sensing Module
240V AC Sensing Module
GFSM120x
GFSM240x
x= A (Automatic) or M (Manual) Set
GFCI Sensing Module
Circuit Breakers
Catalog Number Configurator.
Example: GFSMCB120401P
GFSMCB
Ground Fault
Sensing Module
Circuit Breaker
Circuit Guard ®
Hard Wired 30A GFCI
UL Type 4X Rated
NEC® is a registered trademark of the National Fire Protection
Association (NFPA).
Description
Voltage
Alarm
Catalog Number
Hard wired;
manual and
automatic set
GFCIs.
120V AC
120V AC
240V AC
240V AC
120/240V AC
3Ø 250V AC
3Ø 120/208V AC
None
Audible
None
Audible
Audible
None
None
GFHW13x05
GFHW13x15
GFHW23x05
GFHW23x15
GFHW33x15
GFHW53x
GFHW43x
x= 1 (Automatic) or 0 (Manual) Set
6
For complete listing of Hubbell Products see our full line catalog.
120
40
120 Volt
1 thru
240 Volt
50 Amp
120/240 Volt
Circuit Guard ® Plug-In
GFCI Portable
15A, 120V AC
1P
1P
2P
3P
GFP315A
Description
Catalog Number
Three outlet plug-in
GFP315A
GFI Tester
120V AC
Description
Catalog Number
Ground fault tester
GFT2G
GFT2G
www.hubbell-wiring.com
Minimize Electrical Shock Hazards
Ground Fault Circuit Interrupters (GFCIs)
GFCIs are also critical for protecting people when using portable line cords and
outlets in a variety of indoor and outdoor applications. Hubbell Circuit Guard GFCI line
cords are available with an Automatic Set feature for providing safety in applications
where equipment is intended for continuous use but where temporary power failure is
undesirable such as pumps, pressure washers or portable lighting. Manual Set GFCIs
are also available for applications where operator injury might occur if equipment were
to restart after a power failure such as drills, saws, lathes and grinders. "Portable GFCI"
provides open-neutral protection for temporary power applications.
Portable GFCI Line Cords
• Provides a watertight housing for maximum safety in
harsh environments
• Available with either automatic and manual set
feature to fit the application
• Bright indicator light provides fault confirmation from
a distance
Portable GFCI Outlets
• Ideal for providing safety in applications requiring
multiple outlets
• Features gasketed cover to protect outlets not in use
• Ensures safety by interrupting power when leakage
to ground is 4 to 6 milliamperes
Ordering Information
Circuit Guard ®
Wired On Straight Blade
Portable GFCI Plugs
15A 125V AC
Circuit Guard ®
Portable GFCI
Line Cords
Description
Length
15A 120V AC 18 in.
6 ft.
15 ft.
25 ft.
20A 120V AC 3 ft.
Industrial Grade
GFCI Cord Line
w/ Stripped Leads
GFP4C15x
GFP6C15x
—
GFP25C15x
GFP3C20M
—
—
GFPOEMx
—
—
x= A (Automatic) or M (Manual) Set
Circuit Guard
Portable GFCI
Line Cords
®
Rating
15A
120V AC
Length
2 ft.
15 ft.
25 ft.
35 ft.
Single
Triple Tap
Cat. No.
Manual set; plug; black GFP5266C
Manual set; plug; yellow GFP5266CY
Manual Set; plug with
GFP1C
1 ft. Line cord
Commercial Grade
Description
Cat. No.
Field Wireable; black
GFP515x
w/ Flying Leads
GFP2Cx GFP2TTx
—
—
—
GFP15Lx
GFP25Cx GFP25TTx —
—
—
GFP35Lx
Circuit Guard ®
In-Line GFCI
2 ft. cord length
Single
Description
x= A (Automatic) or M (Manual) Set
x= A (Automatic) or M (Manual) Set
Description
NEC® 590.6(A)
All 125-volt, single-phase, 15-, 20-, and
30-ampere receptacle outlets that are
not a part of the permanent wiring of
the building or structure and that are
in use by personnel shall have groundfault circuit-interrupter protection
for personnel. For the purposes of
this section, cord sets or devices
incorporating listed ground-fault circuitinterrupter protection for personnel
identified for portable use shall be
permitted.
Triple Tap
Locking
Multiple Outlet
Portable GFCI
Description
www.hubbell-wiring.com
Cat. No.
GFCI Module
UL Type 3R Rated
15A 120V AC GFPIL15125x GFPIL15125TRIx
—
Rating
20A 120V AC
—
—
GFPIL20125LKx 20A, 120V AC;
20A 250V AC
—
—
GFPIL20250LKx 60 Hz
x= A (Automatic) or M (Manual) Set
Rating
4-Outlet; 2-Duplex; 15A 120V AC GFP15M
Manual Set
20A 120V AC GFP20M
Description
Cat. No.
Manual set
Auto set
GFM20
GFM20A
For complete listing of Hubbell Products see our full line catalog.
NEC® is a registered trademark of the National Fire Protection
Association (NFPA).
7
Delivery of Safe Convenient Temporary Power
Temporary Power
Construction sites and outdoor events need to ensure maximum safety when providing
temporary electrical power for equipment and lighting, especially since these applications
involve frequent plug-ins and disconnects. Hubbell temporary power distribution systems
come in a variety of device types for protecting people against electrical shock in a wide
range of applications and job sites.
SPIDER® II Temporary Power Boxes
• Incorporates the most advanced ground fault
module technology for safety
• Accommodates watertight straight blade and
Safety-Shroud® Twist-Lock® receptacles
• Heavy Duty UL Type 3R metallic enclosure
Portable Outlet Boxes
NEC® 110.12(A) (Unused Openings)
Unused openings, other than
those intended for the operation of
equipment, those intended for mounting
purposes, or those permitted as part of
the design for listed equipment, shall be
closed to afford protection substantially
equivalent to the wall of the equipment.
• Provides a safe rugged portable enclosure that can
be used in many applications and complies with
NEC® 110.12 regarding unused cable openings in
metallic boxes
NEC 110.12 Mechanical Execution
of Work. Electrical equipment shall
be installed in a neat and workmanlike
manner.
®
• Provides Type 3R protection with weatherproof
cover plates
• Maximize strain relief protection with the addition of
a Kellems® mesh grip
Ordering Information
Temporary Power Boxes
Max Rating
Type
Receptacle Rating
Receptacle Type
Protection
Overload/GFI Straight Blade Twist-Lock®
Spider® II
30A, 120/240V AC
Spider® II
50A, 120/240V AC
Spider® II
60A, 3Ø 120/208V
50A 125/240V AC
(7) Receptacles
(1) Twist-Lock® (inlet & outlet)
(7) Receptacles
(1) Twist-Lock® (inlet & outlet)
(6) Receptacles
(1) Pin and Sleeve (inlet & outlet)
(6) Receptacles
(1) (1) Twist-Lock®
(1) Twist-Lock® (inlet & outlet)
20A, 125V
30A, 120/240V
20A, 125V
50A, 125/250V
20A, 125V
60A, 3ØY, 120/208V
20A, 125V
30A, 250V
50A 125/250V
Yes/Yes
No/No
Yes/Yes
No/No
Yes/Yes
No/No
Yes/Yes
Yes/No
No/No
SDSB1A
SDTL1A
SBSB1A
SBTL1A
SCSB0
SCTL0
TPDS
TPDL
Portable Outlet Boxes and Plates
NEC® is a registered trademark of the National Fire Protection
Association (NFPA).
Description
Catalog Numbers
Box with cord strain relief, with one blank cover plate
Box with cord strain relief, with two duplex (indoor) cover
plates
Blank, non-metallic FS cover plate with foam gasket, gray
Duplex, non-metallic FS cover plate, gray
Single receptacle (1.39"), non-metallic FS cover plate, gray
Single receptacle (1.56"), non-metallic FS cover plate, gray
Rectangular opening, non-metallic FS cover plate, gray
HBLPOB1
HBLPOB1D*
HBLP14FS
HBLP8FS*
HBLP7FS
HBLP720FS
HBLP26FS
* Add Y for Yellow
8
For complete listing of Hubbell Products see our full line catalog.
www.hubbell-wiring.com
Plug and Play Power System
Modular Power
Factories and industrial environments often need flexible power distribution systems
for all types of equipment. Hubbell LINKOSITY® modular power distribution system is
ideal for ensuring safety when providing flexible power in these applications. Hubbell
LINKOSITY® provides the necessary system components to create code compliant safe
installations.
LINKOSITY®
• Reconfigurable factory defined assemblies that can
be easily installed as a cost effective alternative to
conventional wiring methods
• Cables are UL Type TC-ER with the crush and
impact resistance of metal clad cable for maximum
safety in industrial environments
• Enables fast installation and high technical
performance for 20A and 30A circuits up to 600V
• Power assemblies available in straight blade and
Twist-Lock® receptacles
NEC® Article 670 on Industrial
Machinery refers to NFPA 79-2007,
Electrical Standard for Industrial
Machinery where sections 14.1.2.2
and 14.1.5.1 specifically indicate that
molded connections factory-applied to
cable and cords are to be permitted.
NEC® 336.10(7)
Permits type TC-ER cable in transitions
between cable trays and the utilization
equipment or devices when secured
at intervals not more than 6 ft without
continuous support.
Ordering Information
Power Components
20A, 30A up to 600V
Cables and Receptacles
Device Type
Ratings
PH
PM
PN
PF
PG
PQ
PR
PS
RF
RM
20 20A up to 600V
Double Ended Cable - Male/Female Straight
Male Single Ended Straight
Male Single Ended 90°
Female Single Ended Straight
Female Single Ended 90°
Double Ended Cable with Female 90°
Double Ended Cable with Male 90°
Double Ended Cable with (2) 90° Connectors
Female Receptacle; ½" N.P.T. rear thread
Male Receptacle (Inlet); ½” N.P.T. rear thread
Wires
Conductor Colors** Length (ft.)
02 - 05 PA
Green/Yellow;
Black (all others)
23 20A up to 600V
03 PB
Specialty construction
04 Green/Yellow
(Includes isolated ground
05 White
on 6 wire and 10AWG
06 Black (all others)
super neutral conductor
**other color
on 5 and 6 wire devices)
30 30A up to 600V
04 codes available
upon request
001
005
010
015
020
025
030
035
040
045
050
1'
5'
10'
15'
20'
25'
30'
35'
40'
45'
50'
Example Catalog Number: PH2306PB05
LINKOSITY® Tees
Description
Catalog Numbers
M/F/F Tee, 20A, 2P
M/F/F Tee, 20A, 3P
M/F/F Tee, 20A, 4P
M/F/F Tee, 20A, 5P
M/F/F Tee, 20A SNIG, 4P
M/F/F Tee, 20A SNIG, 6P
M/F/F Tee, 20A SNIG, A Phase Tap
M/F/F Tee, 20A SNIG, B Phase Tap
M/F/F Tee, 20A SNIG, C Phase Tap
M/F/F Tee, 30A, 4P
TX2002002002T00
TX2003002003T00
TX2004002004T00
TX2005002005T00
TX2304002304T00
TX2306002306T00
TX2306002304A00
TX2306002304B00
TX2306002304C00
TX3004003004T00
www.hubbell-wiring.com
Closure Caps
Description
For use with
Female Receptacle Male Inlet
20A and 30A CCMBC
Receptacle
Closure Cap
CCFBC
For complete listing of Hubbell Products see our full line catalog.
NEC® is a registered trademark of the National Fire Protection
Association (NFPA).
9
Line of Sight Disconnect Means
Motor Control
Hubbell motor control devices can safely disconnect power at any point in a circuit
without powering down other equipment and sacrificing productivity. The NEC® requires
motor controllers on equipment like HVAC units, compactors and back-up generators
to have a disconnect within line of sight and allows a controller and disconnect to be
the same device. By combining both functions in one device, Hubbell CIRCUIT-LOCK®
eliminates the confusion of which switch is a motor controller or disconnect, providing
owners and operators with a renewed level of comfort and safety.
Circuit-Lock® Unfused Disconnect Switches
• Meets line of sight disconnect requirements to ensure
maximum safety
• High visibility handle is lockable to meet OSHA
lockout/tagout requirements 29CFR 1910.147
• Switch cannot be turned ON unless the Type 4X
enclosure cover is closed
• NEC 430.109(A)(6) recognizes that a manual motor
controller and disconnect can be the same unit
Circuit-Lock® Fused Disconnect Switches
NEC® 430.75(A) Disconnection.
Motor control circuits shall be
arranged so that they will be
disconnected from all sources of
supply when the disconnecting
means is in the open position.
The disconnecting means shall be
permitted to consist of two or more
separate devices, one of which
disconnects the motor and the
controller from the source(s) of power
supply for the motor, and the other(s),
the motor control circuit(s) from its
power supply. Where separate devices
are used, they shall be located
immediately adjacent to each other.
• Certified for current interrupting at full rated current
and voltage
• High visibility red handle can be locked in OFF position
• Type 4X enclosure with neoprene watertight gasket
• Accepts class "J" fuses
• Meets NEC 300.6(D) mounting requirements
Ordering Information
IP66
SUITABILITY
Circuit-Lock®
30 and 60 Ampere
Fused Disconnect Switches
Circuit-Lock®
Unfused Disconnect Switches
Description
Catalog No.
30A disconnect switch
30A disconnect switch with one
HBLAC1 auxiliary contact
60A disconnect switch
60A disconnect switch with one
HBLAC1 auxiliary contact
100A disconnect switch
100A disconnect switch with one
HBLAC1 auxiliary contact
HBLDS3
HBLDS3AC
10
FDS30*
FDS60*
Note: *Class "J" fuses not included.
HBLDS10
HBLDS10AC
Auxiliary Contacts
Catalog No.
Watertight Closure
Plug Kits
Auxiliary contacts, “break after main break” HBLAC1
1 set of n/o & n/c contacts
Auxiliary contacts, “break before main
HBLAC2
break”1 set of n/o contacts
NEC® is a registered trademark of the National Fire Protection
Association (NFPA).
Catalog No.
30A fused disconnect switch
60A fused disconnect switch
HBLDS6
HBLDS6AC
Auxiliary Contacts
for 30, 60 and 100A Switches
Description
Description
Description
Catalog No.
Normally open;A600 pilot duty
Normally closed;A600 pilot duty
ACFSNO
ACFSNC
Description
Catalog No.
For 30A fused disconnect switch MICPK30
For 60A fused disconnect switch MICPK60
Ground Block
Description
Catalog No.
For 30A switches.
For 60A and 100A switches.
HBL30RGB
HBL60100RGB
For complete listing of Hubbell Products see our full line catalog.
www.hubbell-wiring.com
Installation Safety
Motor Control
Hubbell motor control devices are also available for use with Hubbell LINKOSITY®
modular plug-and-play power distribution system. MotorQuick® offers the functionality of
a motor disconnect switch with the safety of factory pre-wired connections. LINKOSITY®
connections make motor change outs fast and simple. Heavy duty manual motor
controllers are also available for controlling and disconnecting power to equipment.
MotorQuick®
• Combines Circuit-Lock® motor disconnect with plug-
and-play LINKOSITY® system for faster installation and
replacement of motors
• Lockable handle meets OSHA lockout/tagout regulations
• Easily retrofits to existing hard wired installations with
LINKOSITY® components
Manual Motor Controllers
• Available in double-pole and three-pole 30A and
60A 600V AC controllers
• Suitable as a motor disconnect
• Type 1 and Type 3R enclosures available
• Optional finger guards (HBLFG30) fit 30A, 40A and
50A controllers
Ordering Information
Manual Motor
Controller
Type 1
30A 3 Pole 600V AC
Description
Catalog No.
HBL1389D with (1) pre-wired
LINKOSITY® female receptacle (load
side)
HBL1389D with 5 ft. pre-wired
LINKOSITY® female cable (load side)
HBL1389D with (1) pre-wired
LINKOSITY® male receptacle (line side)
and (1) pre-wired LINKOSITY® female
receptacle (load side)
HBL1389MQR
HBL1389MQ5
HBL1389MQR2
Description
Double Pole
30A 600V AC motor controller
In Type 1 enclosure;
non-metallic cover
In metal Type 1 enclosure
In NEMA 3R non-metallic
enclosure
In metal Type 3R enclosure
In NEMA 3R flip lid enclosure
60A 600V AC motor controller
HBL7832D
HBL1392D
NEC® 430.102 Location.
(A) Controller.
An individual disconnecting
means shall be provided for each
controller and shall disconnect
the controller. The disconnecting
means shall be located in sight
from the controller location.
(2) Controller Disconnect.
The controller disconnecting
means required in accordance
with 430.102(A) shall be permitted
to serve as the disconnecting
means for the motor if it is in sight
from the motor location and the
driven machinery location.
HBL1372D
HBL13R22D
HBL13R92D
HBL13R12D
HBL7862D
Manual Motor
Controller
Description
Type 4X
30A 3 Pole 600V AC
Description
Catalog No.
HBLDS3 with (1) pre-wired LINKOSITY® HBLDS3MQR
female receptacle (load side)
HBLDS3MQ5
HBLDS3 with 5 ft. pre-wired
LINKOSITY® female cable (load side)
HBLDS3 with (1) pre-wired LINKOSITY® HBLDS3MQR2
male receptacle (line side) and (1)
pre-wired LINKOSITY® female receptacle
(load side)
www.hubbell-wiring.com
Three Pole
30A 600V AC motor controller HBL7810D
In Type 1 enclosure;
HBL1389D
non-metallic cover
In metal Type 1 enclosure
HBL1379D
In NEMA 3R non-metallic
HBL13R23D
enclosure
In metal Type 3R enclosure HBL13R89D
In NEMA 3R flip lid enclosure HBL13R13D
60A 600V AC motor controller HBL7863D
In Type 3R enclosure
HBL16R93D
For complete listing of Hubbell Products see our full line catalog.
NEC® is a registered trademark of the National Fire Protection
Association (NFPA).
11
Wire Secureness and Strain Relief
Wire Management
Hubbell wire mesh grips are designed to prevent strain from being transmitted to joints
and terminals on electrical cords, cables and conduit. This provides greater security than
using a fitting alone, making electrical systems safer by preventing cable pull-out and
controlling cable arc-of-bend.The positive action mesh grips distributes loads equally
over the cable jacket.
Strain Relief Grips
• Multi-weave grip products provide arc-of-bend
control minimizing cable damage and extending
cable life
• Ideal for providing maximum safety where conduit
is subject to vibration, motion or strain
• Stainless steel mesh is corrosion resistant and
optional liquidtight fittings provide a watertight seal
Support Grips
• Ideal for ensuring safety by supporting electrical
NEC® 400.10 (Pull at Joints and
Terminals) Flexible cords and cables
shall be connected to devices and to
fittings so that tension is not transmitted
to joints or terminals.
OSHA Regulation 29 CFR
1926.405(g)(2)(iv) Strain relief.
Flexible cords shall be connected to
devices and fittings so that strain relief
is provided which will prevent pull from
being directly transmitted to joints or
terminal screws.
1926.405(g)(2)(v) Cords passing
through holes. Flexible cords and
cables shall be protected by bushings
or fittings where passing through holes
in covers, outlet boxes, or similar
enclosures.
NEC® is a registered trademark of the National Fire Protection
Association (NFPA).
cable service drops or hoses
• Positive action mesh grip design provides equal
loading throughout the entire grip length
• Available in heavy duty, standard and light duty for a
variety of applications
Ordering Information
Kellems® Deluxe
Cord Grips
Description
Grip Diameter Range
Catalog No.
Straight male
thread; ³⁄₈ in.
N.P.T. thread size
Straight male
thread; ¹⁄₂ in.
N.P.T. thread size
.250"-.312" (.63-.79)
.312"-.375" (.79-.95)
.375"-.437" (.95-1.11)
.187"-.250" (.47-.63)
.250"-.375" (.63-.95)
.375"-.500" (.95-1.27)
.500"-.625" (1.27-1.59)
07401001
07401002
07401003
07401004
07401006
07401008
07401010
90º male thread;
³⁄₈ in. N.P.T.
thread size
90º male thread;
¹⁄₂ in. N.P.T.
thread size
.250"-.312" (.63-.79)
.312"-.375" (.79-.95)
.375"-.437" (.95-1.11)
.187"-.250" (.47-.63)
.250"-.375" (.63-.95)
.375"-.500" (.95-1.27)
.500"-.625" (1.27-1.59)
07401071
07401072
07401073
07401074
07401076
07401078
07401080*
45º male thread;
¹⁄₂ in. N.P.T.
thread size
45º male thread;
³⁄₄ in. N.P.T.
thread size
.250"-.312" (.63-.79)
.375"-.500" (.95-.1.27)
.500"-.625" (1.27-1.59)
.500"-.625" (1.27-1.59)
.625"-.750" (1.59-1.90)
.750"-.875" (1.90-2.22)
074011236
074011021
074011237
074011049
074011051*
074011239*
* Cable jacket may have to be stripped to pass through
connector body.
12
Single Eye, Closed Mesh**
For permanent support when
cable end is available to be
installed through grip.
Cable Diameter
Range Inches (cm)
Approx. Breaking
Strength Lbs. (N) Catalog No.
.50"-.62" (1.27-1.57)
.63"-.74" (1.60-1.88)
.75"-.99" (1.90-2.51)
1.00"-1.24" (2.54-3.15)
1.25"-1.49" (3.17-3.78)
1.50"-1.74" (3.81-4.42)
530 (2,357)
790 (3,514)
1,020 (4,537)
1,610 (7,161)
1,610 (7,161)
1,610 (7,161)
02201013
02201014
02201015
02201017
02201018
02201019
**Change catalog number from 022 to 024 for stainless
steel. Consult factory for availability.
Single Eye, Split Mesh,
Rod Closing**
For support when cable
end is not available.
Cable Diameter
Range Inches (cm)
Approx. Breaking
Strength Lbs. (N) Catalog No.
.50"-.62" (1.27-1.57)
.63"-.74" (1.60-1.88)
.75"-.99" (1.90-2.51)
1.00"-1.24" (2.54-3.15)
1.25"-1.49" (3.17-3.78)
1.50"-1.74" (3.81-4.42)
790 (3,514)
790 (3,514)
1,020 (4,537)
1,610 (7,161)
1,610 (7,161)
1,610 (7,161)
02203013
02203014
02203015
02203017
02203018
02203019
**Change catalog number from 022 to 024 for stainless
steel. Consult factory for availability.
For complete listing of Hubbell Products see our full line catalog.
www.hubbell-wiring.com
Protect Wires from Moisture and Damage
Wire Management
Protecting electrical circuitry on the factory floor improves safety for both people and
equipment by preventing mechanical damage and moisture from impacting the integrity of
the wiring. Hubbell PolyTuff® non-metallic liquidtight conduit and fittings are commonly used
between disconnect switches and equipment in industrial applications to protect wiring
and improve safety. Metallic liquidtight fittings are also available for certain applications.
PolyTuff® Non-Metallic Liquidtight Conduit and Tubing
• Non-metallic construction ends metal fatigue and
separation problems
• Cuts cleanly with a knife or PVC cutter with no
jagged metal edges
• Handles twists, turns, bends, swtichbacks and
straightaways with ease
• Available with rigid PVC core PolyTuff® I or flexible
corrugated wall PolyTuff® II
PolyTuff® Liquidtight Fittings
• SwivelLok® nylon two-piece swivel body enables
fitting to twist from 0° to 90°
• Neoprene O-ring ensures liquidtight seal at hub
or enclosure
• Non-integral ferrule provides conduit seal and
superior pullout protection
Ordering Information
PolyTuff I ® Conduit and
PolyTuff II ® Tubing
Trade Size
(metric designator) Feet (m)
PolyTuff I
Conduit
PolyTuff II
Tubing
¼ (10)
³⁄₈ (12)
½ (16)
¾ (21)
1 (27)
1¼ (35)
1½ (41)
2 (53)
—
G1038
G1050
G1075
G1100
G1125
G1150
G1200
B2025
B2038
B2050
B2075
B2100
B2125
B2150
B2200
100 (30.5)
100 (30.5)
100 (30.5)
100 (30.5)
100 (30.5)
100 (30.5)
50 (15.2)
50 (15.2)
SwivelLok® Multi-Position
with Male Non-Metallic
Liquidtight Fittings
Trade Size
(metric designator)
Black
Gray
³⁄₈ (9)
½ (13)
¾ (19)
1 (25)
PS0389NBK
PS0509NBK
PS0759NBK
PS1009NBK
PS0389NGY
PS0509NGY
PS0759NGY
PS1009NGY
½ (13)
¾ (19)
www.hubbell-wiring.com
¼ (6)
³⁄₈ (9)
½ (13)
¾ (19)
1 (25)
1¼ (32)
1½ (38)
2 (51)
F2025
P038NBKA
P050NBKA
P075NBKA
P100NBKA
P125NBK
P150NBK
P200NBK
Trade Size
(metric designator) Black
Fitting and Conduit Kit Catalog No.
(2) PS0509NGY,
6' G1050
(2) PS0759NGY,
6' G1075
Trade Size
(metric designator) Black
Gray
–
P038NGYA
P050NGYA
P075NGYA
P100NGYA
P125NGY
P150NGY
P200NGY
(1)Where flexibility is required for
installation, operation, or maintenance.
(2)Where protection of the contained
conductors is required from vapors,
liquids or solids.
(3)For outdoor locations where listed and
marked as suitable for the purpose.
(4)For direct burial where listed and
marked for the purpose.
(5)Type LFNC-B shall be permitted to
be installed in lengths longer than 1.8
m (6 ft) where secured in accordance
with 356.30.
(6)For encasement in concrete where
listed for direct burial and installed in
compliance with 356.42.
Fixed 90°Fittings
for Non-Metallic Conduit
SwivelLok®
Flexible Conduit Kit
Trade Size
(metric designator)
Straight with Male
Non-Metallic Fittings
for Non-Metallic Conduit
NEC® 356.10 Uses Permitted. LFNC
shall be permitted to be used in exposed
or concealed locations for the following
purposes:
PS05GYKIT
PS07GYKIT
¼ (6)
³⁄₈ (9)
½ (13)
¾ (19)
1 (25)
1¼ (32)
F20259
P0389NBK
P0509NBK
P0759NBK
P1009NBK
P1259NBK
Gray
–
P0389NGY
P0509NGY
P0759NGY
P1009NGY
P1259NGY
For complete listing of Hubbell Products see our full line catalog.
NEC® is a registered trademark of the National Fire Protection
Association (NFPA).
13
Comply with OSHA Safe Work Practices
Arc Flash Safety
An arc flash is a short circuit that travels through air from one live circuit to another.
Problems including gaps in insulation, dust or corrosion on the surface of a conductor,
or even use of substandard components can cause a serious safety hazards and
equipment failures. Arc flash incidents can be extremely costly to a business and can
result in serious or even fatal burns, as well as damage to eyesight. Hubbell PANELSAFE™ and mechanical interlocks provide arc flash safety by ensuring isolation from live
electrical components.
Panel Safe
• Available in Type 4, 12 and 4X versions with
protective clear cover
• Provides overcurrent protection for both power
and data access ports
• Ensures safety with finger-safe contacts and
Hubbell GFCI functionality
Mechanical
Interlock
• Eliminates the possibility of making and breaking the
NFPA 70E:
• Electrical equipment enclosures
can ONLY be accessed by qualified
personnel with extensive protective
clothing and equipment, including
fire-resistant suits and hoods with
non-conductive wands.
NFPA 79: Electrical Standard for
Industrial Machinery
• ALL utility receptacles must be
GFCI protected
• ALL external utility receptacles
must be covered
• ALL covers must maintain
enclosure rating
circuit under load providing safe connections to portable
equipment
• Non-metallic enclosure can be connected to metallic
conduit and not interfere with the ground continuity
• Highly visible red handle can be locked out to comply
with OSHA lockout/tagout regulations
• UL/CSA certified as a manual motor controller and also
as suitable as a disconnect
Ordering Information
PANEL-SAFE™
Access Ports
Description
Power Only
20A 125V GFCI with
In-Cabinet Receptacle
Data Only
Cat. 5e Ethernet Access only
DB9 Interface Connector only
DH + Combo (DB9/8M Din)
and Cat. 5e Ethernet
Power and Data
20A 125V GFCI with
In-Cabinet Receptacle and
Cat. 5e Ethernet Access
20A 125V GFCI with
In-Cabinet Receptacle,
Cat. 5e Ethernet Access and
3A Circuit Breaker
20A 125V GFCI Power and
Cat. 5e Ethernet, DH +
Combo (DB9/8M Din)
15A 125V Power and
Cat. 5e Ethernet Access
15A 125V Power, Cat. 5e
Ethernet Access and
3A Circuit Breaker
15A 125V Power and
(2) Cat. 5e Ethernet Access
14
IEC Watertight
Pin & Sleeve
Rating Color Coded
by Voltage
20A
3Ø 480V
30A
3Ø 250V
30A
3Ø 480V
30A
3Ø 600V
30A
3ØY 277/480V
60A
3Ø 250V
60A
3ØY 120/208V
60A
3Ø 480V
60A
3Ø 600V
100A
250V
100A
3ØY 120/208V
100A
3Ø 480V
100A
3Ø 600V
NEMA
NEMA
TYPE 4, 12 TYPE 4X
PR20
—
P5E
PDB9
PDH5E
P4X5E
—
—
PR205E
PR4X205E
PR205EB PR4X205EB
P20DH5E
—
P155E
P4X155E
P155EB
P4X155EB
P155E2
—
Poles/
Wires
Mechanical
Interlock
3P 4W HBL420MI7W
3P 4W HBL430MI9W
3P 4W HBL430MI7W
3P 4W HBL430MI5W
4P 5W HBL530MI7W
3P 4W HBL460MI9W
4P 5W HBL560MI9W
3P 4W HBL460MI7W
3P 4W HBL460MI5W
3P 4W HBL4100MI9W
4P 5W HBL5100MI9W
3P 4W HBL4100MI7W
3P 4W HBL4100MI5W
For mating plug, replace MI with P. Ex. HBL420MI7W
(mechanical interlock) to HBL420P7W (mating plug)
For complete listing of Hubbell Products see our full line catalog.
www.hubbell-wiring.com
Safe Maintenance and Repairs
Lockout, Tagout for Electrical Safety
Lockout/tagout refers to specific procedures to safeguard people from the unexpected
energization or startup of machinery and equipment, or the release of hazardous energy
during service or maintenance activities. Hubbell offers many products that meet OSHA
lockout/tagout regulations including integrated lockout features in pin and sleeve plugs
and switched enclosures as well as a variety of dedicated lockout devices.
PLUGOUT® and SWITCHOUT® Lockout Devices
• Provides an approved method of complying with
OSHA lockout/tagout regulation
• Available in 15A, 20A, 30A and 60A plugout
devices enclose the equipment plug and secure
with a key padlock
Locking Switches
• Prevents unauthorized control of lighting or
ventilation control
• Keys supplied with each locking switch
• One piece integral grounding terminal provides a
low resistance ground path
Ordering Information
PLUGOUT®
Lockout Devices
Description
Typical Devices Accommodated Catalog No
Small yellow
lockout device
Medium yellow
lockout device
15 and 20A straight blade
HLDMP
plugs;15A Twist-Lock® plugs
HLD
15 and 20A, 125V straight
blade plugs; 20 and 30A
Twist-Lock® plugs
20, 30 and 60A metallic and HLD2
non-metallic Pin and Sleeve;
Hubbellock®; 50A Twist-Lock®
plugs
Large yellow
lockout device
SWITCHOUT®
Yellow Switchout Toggle switch
device
Keyed PLUGOUT
Yellow keyed
15 and 20A, 125V straight
Plugout; keyed blade; plugs with holes in
differently
blades
Yellow keyed
15 and 20A, 125V straight
Plugout; keyed blade; plugs with holes in
alike
blades
* Two devices per package
HSLDPK2*
www.hubbell-wiring.com
This section requires employers
to establish a program and utilize
procedures for affixing appropriate
lockout devices or tagout devices
to energy isolating devices, and
to otherwise disable machines or
equipment to prevent unexpected
energization, start up or release of
stored energy in order to prevent injury
to employees.
AC Barrel Key
Locking Switches
20 Amp 120-277 Volt
Description
Catalog Numbers
Single pole
Double pole
Three-Way
Four-Way
Barrel key replacement
HBL1221RKL
HBL1222RKL
HBL1223RKL
HBL1224RKL
HBL1209RKL
Locking Switches
15 Amp 120-277 Volt
Description
Catalog Numbers
HKLD
Single pole
Double pole
Three-Way
Four-Way
HBL1201L
HBL1202L
HBL1203L
HBL1204L
HKLDPK2*
20 Amp 120-277 Volt
®
NFPA 70E-2004 LO/TO Procedures
29CFR1910.147(a)(3)(i)
Description
Catalog Numbers
Single pole
Double pole
Three-Way
Four-Way
Replacement key
HBL1221L
HBL1222L
HBL1223L
HBL1224L
HBL1209
For complete listing of Hubbell Products see our full line catalog.
NEC® is a registered trademark of the National Fire Protection
Association (NFPA).
15
Eliminate Tripping Hazards
Cable Management
Cable reels can help eliminate unmanaged cords and cables that would otherwise cause
trip hazards or an increased potential of electric shock. Hubbell offers a wide range of
cord reels that provide cable protection, including watertight, industrial, commercial and
static discharge reels with grounding jaw clamps for a low resistant ground termination
for maximum safety.
Industrial Cord Reels
• Provide safe convenient power and lighting
for demanding industrial applications and
environments
• All steel construction can be ceiling. wall or
bench mounted
• Keeps cord organized and off the floor, saves
time and money and improves safety while
extending cord life
Commercial Cord Reels
• Lighter weight for the less demanding requirements
UL355 4.3, 4.4
Cord Reels, that employ GroundFault Circuit Interrupter outlet(s) and
are connected to the power supply
by means of flexible cord with an
attachment plug and/or that employ
slip rings, shall be provided with open
neutral protection as part of the GFCI.
AFL version allows cord reel installation
to conform to NEC® Article 511
concerning installation of electrical
devices in commercial garages,
repair facilities and storage locations
by positioning the switch above the
defined area where hazardous fumes
may collect.
of commercial and light industrial environments
• Eliminates unmanaged cords which can cause trip
hazards or an increased potential of electric shock
• AFL version provides automatic lamp shut-off to
switch power above the floor height requirement
• Holds cord at desired length and provides smooth
cord retraction
Ordering Information
Industrial Power Cord Reels
Cord End
NEMA
Style
HBL5269C 15A connector
HBL5369C 20A connector
Portable duplex outlet box; 15A gray duplex
Portable duplex outlet box; 20A gray duplex
Portable duplex outlet box; 15A gray GFCI duplex
Portable duplex outlet box; 20A gray GFCI duplex
HBL2313 20A connector
Pivot Base 330° Rotation
5-15R
5-20R
5-15R
5-20R
5-15R
5-20R
5-20R
–
Cable
Volts
Feet (m) AC Cable Type
45 (13.7)
45 (13.7)
45 (13.7)
45 (13.7)
45 (13.7)
45 (13.7)
45 (13.7)
–
125
125
125
125
125
125
125
–
Weight
Lbs. (kg) Catalog Number
12/3 SJEO
12/3 SJEO
12/3 SJEO
12/3 SJEO
12/3 SJEO
12/3 SJEO
12/3 SJEO
–
23 (10.4)
29 (13.2)
29 (13.2)
29 (13.2)
29 (13.2)
28 (12.7)
23 (10.4)
5 (2.3)
HBL45123C
HBL45123C20
HBL45123R
HBL45123R20
HBL45123GF15
HBL45123GF20
HBL45123TL20
HBL340PB
Commercial Cord Reels
Cord End
NEC® is a registered trademark of the National Fire Protection
Association (NFPA).
16
Triple tap outlet; 15A
Wire leads; 10A
HBL5969VBLK connector; 10A
Metallic incandescent hand lamp with
receptacle; 13A
Fluorescent hand lamp and inline
receptacle; 10A
Fluorescent hand lamp; automatic shut
off switch; 0.3A
Watts
(Max)
Cable
Feet (m)
Volts
AC
Cable Type
Weight
Lbs. (kg)
Catalog Number
1200
1250
1250
1625
40 (12.2)
25 (7.6)
25 (7.6)
25 (7.6)
125
125
125
125
12/3 SJTW
16/3 SJT
16/3 SJT
14/3 SJT
9 (4.1)
8.5 (3.9)
8.5 (3.9)
9.5 (4.3)
HBLC40123TT
HBLC25163
HBLC25163C
HBLC25143IN
1200
40 (12.2)
120
16/3 SJT
9 (4.1)
HBLC40163FL
13
40 (12.2)
120
18/2 SJTOW 8.2 (3.7)
For complete listing of Hubbell Products see our full line catalog.
HBLC40182AFL
www.hubbell-wiring.com
Prevent Damage to Cables
Hose and Cable Protection Systems
Exposed cables, cords and hoses can be a trip hazard for pedestrians, as well as a
potential shock hazard. Hubbell offers a variety of hose and cable protection systems
that provide a safe ramping system for both pedestrians and vehicles to pass over
cables and hoses.
TrukTrak® and TredTrak®
• Safeguards cables and cords from vehicle and
pedestrian traffic
• TrukTrak® is ideal for industrial environments where
trucks and forklifts are present
• TredTrak® supports pedestrian and light vehicle traffic
in public, institutional and commercial applications
• Complies with NEC Article 525 for insulating cables
at carnivals, amusement parks, convention centers
and similar public areas
AccessTrak®
• Modular cable protection for compliance with ADA
accessibility guidelines
• Expandable five channel system that limits exposure of
cables and hoses
• Protects cable and hose diameters up to 1.31 inches
NEC® 110(F)(2)
Outdoor. Outdoor electrical equipment
shall be installed in suitable enclosures
and shall be protected from accidental
contact by unauthorized personnel, or by
vehicular traffic.
OSHA 1926.416(e)(1)
Requires that worn or frayed electrical
cords or cables shall not be used.
Precautions to mitigate wear include
protection from damage and pinch points
Ordering Information
TrukTrak® and TredTrak® Systems
Description
TrukTrak®
TredTrak®
5 Channel, blue and yellow
5 Channel end caps (pair only), yellow
5 Channel female end caps (2 females), yellow
5 Channel 45° right turn, blue and yellow
5 Channel 45° left turn, blue and yellow
5 Channel “X” fitting, blue and yellow
5 Channel “Y” fitting, blue and yellow
3 Channel, blue and yellow
3 Channel end caps (pair only), yellow
2 Channel, blue and yellow
HBLTT5B
HBLTT5ECB
—
HBLTT545RB
HBLTT545LB
—
—
HBLTT3B
HBLTT3ECB
HBLTT2B
HBLTRED5B
HBLTRED5ECB
HBLTRED5ECFB
—
—
HBLTRED5XB
HBLTRED5YB
—
—
—
AccessTrak® System
Description
Catalog Number
5 Channel AccessTrak kit*, blue and gray
5 Channel AccessTrak trough, blue and gray
AccessTrak trough end rails (set), gray
AccessTrak ramps (set), blue
AccessTrak ramp end rails (set), gray
HBLAT5KITA
HBLAT5A
HBLAT5ERA
HBLAT5RAMPA
HBLAT5RAMPERA
*Consists of (1) HBLAT5A; (1 set) HBLAT5ERA; (1 set) HBLAT5RAMPA; (2 sets)
HBLRAMPERA.
www.hubbell-wiring.com
Expanded by Length
Expanded by Width
For complete listing of Hubbell Products see our full line catalog.
NEC® is a registered trademark of the National Fire Protection
Association (NFPA).
17
Enhanced Safety for Convenience Outlets
Specialty Devices
Hubbell knows that safety of people should be first in every environment. Hubbell offers
a wide variety of receptacles all designed and developed to provide maximum safety
from the factory floor to the doctor’s office to the outdoor amusement park. Hubbell’s
HBL® Extra Heavy Duty Industrial Series receptacles reduce heat buildup and provide
low resistance of fault currents while Hubbell Tamper-Resistant and Weather-Resistant
receptacles provide an additional level of safety now required for use in dwelling units
and wet and damp locations.
HBL® Extra Heavy Duty Industrial Series Receptacles
• Reinforced thermoplastic polyester base for heat
resistance and contact stability
• Exclusive nickel-plated bypass contact design
ensures uninterrupted power
• Four-point grounding system provides redundant
grounding for low resistance
• Meets NEC® 406.9 requirements
WR
Tamper-Resistant and Water Resistant Receptacles
• Spring-loaded shutter restricts access to live contacts
NEC® 406.9(B)(1) – REVISED
[Formerly 406.8(B)(1)]
by single-pronged items for maximum safety
• Only proper plug insertion opens the shutters,
2011 NEC® wording:
406.9 Receptacles in Damp or Wet
Locations. All 15- and 20-ampere, 125and 250-volt nonlocking-type receptacles
shall be listed weather-resistant type.
406.12 Tamper-Resistant Receptacles
in Dwelling Units. In all areas specified in
210.52, all nonlocking type 125-volt, 15and 20-ampere receptacles shall be listed
tamper-resistant receptacles.
406.13 – NEC Tamper-Resistant
Receptacles in Guest Rooms and Guest
Suites. All nonlocking-type, 125-volt,
15- and 20-ampere receptacles located in
guest rooms and guest suites shall be listed
tamper-resistant receptacles.
406.14 – NEC Tamper-Resistant
Receptacles in Child Care Facilities.
In all child care facilities, all nonlocking-type,
125-volt, 15- and 20-ampere receptacles
shall be listed tamper-resistant receptacles.
allowing electrical contact
• Tamper resistant meets NEC® 406.12, 406.13 and
406.14 requirements
TR
• Weather resistant meets NEC® 406.9 requirements
WR
Ordering Information
HBL® Extra Heavy Duty
Industrial Series
NEMA
15A 125V
NEMA 5-15R
20A 125V
NEMA 5-20R
Rating
Color
15A 125V Brown
Black
Ivory
Other
20A 125V Brown
Black
Ivory
Other
Receptacle
Circuit Tester
Duplex
Weather Resistant
Single
Description
HBL5262
HBL5262BK
HBL5262I
HBL5262x
HBL5362
HBL5362BK
HBL5362I
HBL5362x
HBL5262WR
HBL5262BKWR
HBL5262IWR
HBL5262xWR
HBL5362WR
HBL5362BKWR
HBL5362IWR
HBL5362xWR
HBL5261
HBL5261BK
HBL5261I
—
HBL5361
HBL5361BK
HBL5361I
HBL5361xx
Neon lights
HBL5200
visually indicate
and verify various
fault conditions in
electrical circuits
Catalog No.
x=color: GY (Gray), R (Red) and W (White). xx=color: GRY (Gray), and W (White).
TR
Commercial Specification
Grade Receptacles
NEMA
15A 125V
NEMA 5-15R
NEC® is a registered trademark of the National Fire Protection
Association (NFPA).
20A 125V
NEMA 5-20R
Rating
Color
15A 125V Brown
Black
Ivory
Other
20A 125V Brown
Black
Ivory
Other
WR
TR
WR
Standard Duplex Tamper-Resistant Weather Resistant
Tamper-Resistant
Weather Resistant
BR15
BR15BLK
BR15I
BR15x
BR20
BR20BLK
BR20I
BR20x
BR15WRTR
BR15BLKWRTR
BR15IWRTR
BR15xWRTR
BR20WRTR
BR20BLKWRTR
BR20IWRTR
BR20xWRTR
BR15TR
BR15BLKTR
BR15ITR
BR15xTR
BR20TR
BR20BLKTR
BR20ITR
BR20xTR
BR15WR
BR15BLKWR
BR15IWR
BR15xWR
BR20WR
BR20BLKWR
BR20IWR
BR20xWR
x=color: AL (Almond), GY (Gray), LA (Light Almond) and W (White). xx=color: GRY (Gray), and W (White).
18
For complete listing of Hubbell Products see our full line catalog.
www.hubbell-wiring.com
Protect Devices from Corrosion and Abuse
Specialty Devices
Some environments can be particularly corrosive for electrical connections, calling for
an extra level of safety and protection. Hubbell offers a wide range of plugs, connectors
and receptacles that are specifically designed to withstand corrosive environments like
chemical plants and wastewater treatment facilities.
Corrosion Resistant Plugs, Connectors and Receptacles
• Reinforced thermoplastic elastomer housing to
resist ultraviolet rays, oil and chemicals
• Powerful nylon cord grips on plugs prevents strain
on terminals and prevents cord pull-outs
• Plated contacts provide for reliable electrical
connections and long life
Weatherproof Covers
• UL listed for wet locations in both thermoplastic
and cast aluminum with cover closed
• Suffix "WO" are listed for wet location with cover
open and plug installed
• Available in single and dual receptacles with
individual weatherproof covers for each receptacle
Ordering Information
Corrosion
Resistant
Straight Blade
NEMA
15A 125V
NEMA 5-15R
20A 125V
NEMA 5-20R
Twist-Lock®
Rating Device
Catalog Number
15A Duplex Receptacle
125V Duplex Lift Cover
Single Receptacle
Plug
Connector
20A Duplex Receptacle
125V Duplex Lift Cover
Single Receptacle
Plug
Connector
HBL52CM62
HBL52CM21
HBL52CM61
HBL52CM66C
HBL52CM69C
HBL53CM62
HBL52CM21
HBL53CM61
HBL53CM66C
HBL53CM69C
Duplex Covers
Thermoplastic for
Vertical Mounting
Description
NEMA
W
G
15A 125V
NEMA L5-15P
UL/CSA
0.5 HP
W
G
20A 125V
NEMA L5-20P
UL/CSA
1 HP
Rating Device
Catalog Number
15A Duplex Receptacle
125V Duplex Lift Cover
Plug
Connector
Lift Cover
20A Single Receptacle
125V Plug
Connector
Lift Cover
HBL47CM00
HBL52CM21
HBL47CM20C
HBL47CM29C
HBL74CM25WOA
HBL23CM10
HBL23CM11
HBL23CM13
HBL74CM25WOA
Receptacle Covers
Vertical FS/FD Mounting
Gray
Yellow
Face Diameter
For FS/FD box mounting HBL5221 HBL52CM21
For device mounting
HBL5222 HBL52CM22
Duplex Covers
Cast Aluminum for
Horizontal Mounting
Description
406.9 Receptacles in Wet Locations.
(B) Wet Locations.
15- and 20-ampere, 125- and 250-volt
receptacles installed in a wet location shall
have an enclosure that is weatherproof
whether or not the attachment plug cap is
inserted. All 15- and 20-ampere, 125- and
250-volt nonlocking receptacles shall be
listed weather-resistant type. Exception
15- and 20-ampere, 125- through 250volt receptacles installed in a wet location
and subject to routine high-pressure spray
washing shall be permitted to have an
enclosure that is weatherproof when the
attachment plus is removed.
Catalog Number
For FS/FD box mounting HBL5206WO
For device mounting
HBL5205WO
www.hubbell-wiring.com
Cast
Aluminum
inches (mm)
Color
Thermoplastic
1.36"-1.39"
(34.5-35.3)
1.55" - 1.58"
(39.4-35.3)
1.68" - 1.72"
(42.7-43.7)
Gray
Yellow
Gray
Yellow
Gray
Yellow
HBL7423WO
HBL7420
HBL74CM23WO
—
HBL7425WOA
HBL7420*
HBL74CM25WOA
—
HBL7424WO
HBL3393
HBL74CM24WO
—
NEC® is a registered trademark of the National Fire Protection
Association (NFPA).
Wet Locations: Thermoplastic w/ cover "open"
Cast Aluminum w/ cover "closed"
For complete listing of Hubbell Products see our full line catalog.
19
®
HUBBELL Safety
Application Guide
Hubbell Supports Sustainable Building
All around the globe, there is a powerful shift towards “sustainable” thinking. Now
increased interest in energy efficiency and waste reduction has put sustainable building
design at the very forefront of the industrial, commercial and residential construction
industries.
As a leader in the industry, Hubbell Wiring Systems recognizes its role and responsibility
in safeguarding the environment. Through its GreenWise™ Sustainability Initiative, Hubbell
designs and develops innovative products that optimize sustainable building design by
saving energy, supporting space efficiency and reducing waste. Hubbell Wiring Systems
is committed to maintaining environmental stewardship in our own manufacturing and
corporate facilities through restricting the use of hazardous materials, implementing
comprehensive recycling programs and improving energy efficiency.
Website Support
The Hubbell Wiring Systems website features a landing
page dedicated to the GreenWise™ Initiative. Here you can
find quick links to Hubbell's sustainable building products,
resources and councils, financial incentives per state and
support literature.
Literature Support
Hubbell offers an extensive literature library for product
support.
Downloadable PDFs are available online.
Hubbell Watertight
Wiring Devices
Insulgrip® Wiring Devices
Application Guide
Hubbell Wiring DeviceKellems Catalog
WIRING DEVICE SAFETY EVALUATION
Lockout Tagout
Solution
Problem
Problem: A machine is being repaired or set-up. How can
employees be protected from unintentional energizing of
equipment?
Solution: Plugout devices in a full range of sizes, enclose the
equipment plug and secure with a keyed padlock.
NEC Information: Article 430.102 – Explains lock-out tag-out
procedure.
Straight Blade Receptacle 15-20 Ampere
Solution
Problem
Solution
Problem: A toggle switch controls equipment being serviced.
Unintentional actuation of the switch during service presents a
hazard to maintenance personnel.
Solution: Switchout devices on any standard toggle switch to
mechanically lock it in the off position.
NEC Information: Article 430.102 – Explains lock-out tag-out
procedure.
Mechanical Interlock
Switch
Problem
Solution
Problem
Problem: Lighting or ventilation may require only authorized
access to switch.
Solution: Barrel key locking switch prevents unauthorized
on or off activation.
TrukTrak®
Problem
Problem: Electrical, pneumatic and hydraulic cables are
being damaged when driven over and create a trip hazard.
Solution: Protect your cables and hoses with TrukTrak®,
TredTrak® and AccessTrak® non-metallic cable protectors
designed to safeguard electrical cables and cords from
vehicle and pedestrian traffic.
NEC Information: Article 527.4(H) – Protection from
accidental damage indicates that cords shall be protected
from sharp corners and projections.
Solution
Problem: Potential for dangerous arcing when equipment is
unintentionally connected / disconnected under load.
Solution: Circuit-Lock® Switched Mechanical Interlock
Enclosure virtually eliminates the possibility of making or
breaking the circuit under load or making a casual or “lazy”
connection.
NEC Information: Article 430.103 – The disconnecting means
shall open all ungrounded conductors and be designed so that
no pole can be operated independently.
Solution
SAFETY
EVALUATION
A step-by-step checklist to help
identify potential problems, from
the wiring device experts...Hubbell.
Problem: Switch controls equipment that is exposed to
frequent washdowns and cleaning chemicals.
Solution: Circuit-Lock Switched Enclosure with a UL Type 4X
(Washdown, Corrosion Resistant ) rating and a lockable handle
to meet OSHA Lockout / Tagout regulations.
NEC Information: Article 430.91 – Refers to enclosure type
ratings, and Article 430.102 (B) – refers to Lock-out, Tag-out
requirements.
Problem: A standard GFCI receptacle installed in a 4"
square box for temporary power.
Solution: Portable GFCI products with open neutral
protection as required.
OSHA Information: Meets OSHA 29 CRF 1926.404(b)(1)(ii)
and 29 CRF 1926.405(a)(2)(ii)(G) requirements for portable
power/lighting in confined space. Article 305-5 (A).
Continued on back
Problem
Problem: Using a box that is not listed for pendant
application. Open knockouts and inadequate strain relief could
potentially harm equipment or personnel.
Solution: Portable outlet boxes provide a safe rugged portable
enclosure which can be used in many different applications.
NEC Information: Article 110.12 - Refers to unused cable
openings in metallic boxes.
Printed In U.S.A. Specifications subject to change without notice. ® Registered trademark of Hubbell Incorporated.
Hubbell Incorporated (Delaware) • 185 Plains Road • Milford, CT 06460-2420 • (203) 882-4800 •
H5149
FAX (800) 255-1031
We recommend that you begin your safety inspection by
reviewing the condition of existing installed wiring devices.
Strong consideration should be given to upgrading to the
most current wiring device technology and the latest NEC
requirements.
It is extremely important that users adhere to the
manufacturer’s installation instructions when installing
and using wiring devices. Proper product selection for the
given application is important. Wiring devices are designed
to perform specific tasks within the limit of their design,
electrical rating and intended installation environment.
Hubbell offers a complete line of wiring device products
serving a wide range of applications.
A safety checklist by product type (switches, wire
management, plugs/connectors, receptacles, high-amperage
products, ground fault protection and lock-out/tag-out)
outlines some of the “inspection checkpoints” plant
electricians should be aware of when checking various types
of wiring devices. Most inspection points can be done visually
without disassembling the devices.
Solution
Visual inspections not only indicate potential failures of
products; for an experienced maintenance technician they are
an early warning system signaling the possibility of product
failure or of a potential hazard to personnel.
Portable Outlet Box
Solution
Problem
Workplace safety has a significant impact on your business.
Employee safety and productivity, machine down time, and
production throughput are all impacted by the condition
of the work environment. Hubbell Wiring Device Kellems
encourages and promotes a safe and well maintained work
place, through the proper selection, use and installation
of wiring devices. This brochure details applications, NEC
references and product solutions to assist you in achieving
those goals.
Safety Evaluation Checklist
Disconnect Switch
Problem
GFCI
HUBBELL WIRING DEVICE
SAFETY IN THE WORKPLACE
Solution
Problem
Problem: Devices are burning out from coming in contact
with water and debris.
Solution: Safety-Shrouded Twist-Lock® products that are
UL Type 4X rated for use in harsh environments.
NEC Information: Article 110.11 - Refers to deteriorating
agents, and Table 430.91 for environmental type ratings.
Problem: Misapplied receptacles installed in demanding
applications.
Solution: Industrial receptacles are made with impact
resistant nylon faces to minimize damage from impact and
abrupt pull-out. Stainless steel plates also provide excellent
strength and protection.
NEC Information: Article 110.3 & 110.12(C) – Indicates
requirements for the structural integrity of product.
Hubbell Slide Charts
PROBLEMS & SOLUTIONS
PROBLEMS & SOLUTIONS
Plug/Connector
Problem
Hubbell Safety Evaluation
Solution
Common Examples:
Hazard – A receptacle or switch with a
damaged or missing cover plate means
that the terminal screws to
which the conductors are
wired are exposed and could
be touched by a person.
In addition to this potential
hazard, grounding or short
circuiting of the conductors in
the receptacle or switch can
cause equipment, machinery or lighting
failure resulting in downtime.
Hazard – A light switch has been
damaged and will not operate
resulting in a loss of light. This
results in lost productivity
and a condition that can be
dangerous.
Hazard – Plug blades or
pins have been damaged
or tampered with and the rating
designation has been altered or removed.
Altering the contact pattern and blade
configuration allows undesirable
interchangeability. Different
configurations are designed
to prevent mating of
devices with different
ratings. For instance, a
single-phase, 125-volt,
3-wire plug will not fit into a
three-phase, 120/208V receptacle. This is
why it is important during inspections to
make sure contacts patterns are intact.
Hubbell Recommends...
www.hubbellcatalog.com/wiring
www.hubbell-wiring.com
•
Qualified electricians perform all electrical work.
•
Be aware of strict compliances to NEC and OSHA regulations.
•
Always disconnect power and use approved lock-out/tag-out procedures while
inspecting and performing electrical maintenance work.
•
Wiring devices, as with all electro-mechanical devices, require periodic
inspection and maintenance to assure the safety of the user and the proper
day-to-day performance of the product.
•
The following check list is not inclusive but may point to trouble areas in the
installation of wiring devices.
®
Wiring Device-Kellems
www.hubbell-wiring.com
Hubbell Wiring Device-Kellems • Hubbell Incorporated (Delaware) • 40 Waterview Drive • Shelton, CT 06484
Phone (800) 288-6000 • FAX (800) 255-1031
Printed in U.S.A. Specifications subject to change without notice.
®
is a registered trademarks of Hubbell Incorporated.
WLBVM002 10/10
FPO
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement