Operating instructions | Sharp XL-DH229 Stereo System User Manual

Sharp XL-DH229 Stereo System User Manual
ENGLISH
MODEL
XL-DH229P
MICRO COMPONENT SYSTEM
OPERATION MANUAL
XL-DH229P Micro Component System consisting of XL-DH229P (main unit) and CP-DH229P (speaker system).
M I C RO
COM
PON
ENT
SYST
EM
XL-DH229
iPhone, iPod, iPod classic, iPod nano, and
iPod touch are trademarks of Apple Inc.,
registered in the U.S. and other countries.
“Made for iPod” and “Made for iPhone” mean that an electronic accessory has been designed to connect specifically
to iPod or iPhone, respectively, and has been certified by the developer to meet Apple performance standards. Apple
is not responsible for the operation of this device or its compliance with safety and regulatory standards.
Accessories
RRM
CGA
232
AWS
A
Please confirm that the following accessories are included.
iPhone® adaptor x 2
(GCOVAA238AWSA - No 12)
(GCOVAA239AWSA - No 15)
Remote control x 1
(RRMCGA246AWSA)
AM loop antenna x 1
(QANTLA004AWZZ)
FM antenna x 1
(92LFANT1535A)
Special Note
Supply of this product does not convey a license nor imply any right to distribute content created with this product in
revenue-generating broadcast systems (terrestrial, satellite, cable and/or other distribution channels), revenue generating
streaming applications (via Internet, intranets and/or other networks), other revenue-generating content distribution
systems (pay-audio or audio-on-demand applications and the like) or on revenue-generating physical media (compact
discs, digital versatile discs, semiconductor chips, hard drives, memory cards and the like). An independent license for
such use is required. For details, please visit http://mp3licensing.com
MPEG Layer-3 audio coding technology licensed from Fraunhofer IIS and Thomson.
TINSZA756AWZZ
XL-DH229P_USA_EN_cover.indd 1
Printed in Malaysia
11A R AS 1
12/21/2010 5:53:34 PM
SPECIAL NOTES
NOTE
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause
harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or
more of the following measures:
O Reorient or relocate the receiving antenna.
O Increase the separation between the equipment and
receiver.
O Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
O Consult the dealer or an experienced radio/TV
technician for help.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO
NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
Explanation of Graphical Symbols:
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to
alert the user to the presence of uninsulated
“dangerous voltage” within the product’s
enclosure that may be of sufficient
magnitude to constitute a risk of electric
shock to persons.
The exclamation point within an equilateral
triangle is intended to alert the user to
the presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR
MOISTURE.
WARNING
FCC Regulations state that any unauthorized changes or
modifications to this equipment not expressly approved by
the manufacturer could void the user’s authority to operate
this equipment.
This product is classified as a CLASS 1 LASER PRODUCT
Caution - Use of any controls, adjustments or procedures
other than those specified herein may result in hazardous
radiation exposure.
FOR YOUR RECORDS
For your assistance in reporting this unit in case of loss or theft,
please record below the model number and serial number which
are located on the rear of the unit. Please retain this information.
Model number
..............................................
Serial number
..............................................
Date of purchase ..............................................
Place of purchase ..............................................
Note to CATV system installer:
This reminder is provided to call the CATV system installer’s
attention to Article 820 of the National Electrical Code that
provides guidelines for proper grounding and, in particular,
specifies that the cable ground shall be connected to the
grounding system of the building, as close to the point of cable
entry as practical.
IMPORTANT SAFETY INSTRUCTIONS
Electricity is used to perform many useful functions, but
it can also cause personal injuries and property damage
if improperly handled. This product has been engineered
and manufactured with the highest priority on safety.
However, improper use can result in electric shock and/or
fire. In order to prevent potential danger, please observe
the following instructions when installing, operating and
cleaning the product. To ensure your safety and prolong
the service life of this product, please read the following
precautions carefully before use.
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7)
Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
8) Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug
has two blades and a third grounding prong. The wide
blade or the third prong are provided for your safety. If
the provided plug does not fit into your outlet, consult
an electrician for replacement of the obsolete outlet.
10) Protect the power cord from being walked on or
pinched particularly at plugs, convenience receptacles,
and the point where they exit from the apparatus.
E-1
XL-DH229P_USA_EN.indd 1
12/28/2010 3:23:54 PM
IMPORTANT SAFETY INSTRUCTIONS (continued)
11) Only use attachments/accessories specified by the
manufacturer.
12) Use only with the cart, stand, tripod,
bracket, or table specified by the
manufacturer, or sold with the apparatus.
When a cart is used, use caution when
moving the cart/apparatus combination
to avoid injury from tip-over.
13) Unplug this apparatus during lightning storms or when
unused for long periods of time.
14) Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has
been exposed to rain or moisture, does not operate
normally, or has been dropped.
Additional Safety Information
15) Power Sources - This product should be operated
only from the type of power source indicated on the
marking label. If you are not sure of the type of power
supply to your home, consult your product dealer or
local power company. For product intended to operate
from battery power, or other sources, refer to the
operating instructions.
16) Overloading - Do not overload wall outlets, extension
cords, or integral convenience receptacles as this can
result in a risk of fire or electric shock.
17) Object and Liquid Entry - Never push objects of any
kind into this product through openings as they may
touch dangerous voltage points or short-out parts that
could result in a fire or electric shock. Never spill liquid
of any kind on the product.
18) Damage Requiring Service - Unplug this product from
the wall outlet and refer servicing to qualified service
personnel under the following conditions:
a) When the AC cord or plug is damaged,
b) If liquid has been spilled, or objects have fallen
into the product,
c) If the product has been exposed to rain or water,
d) If the product does not operate normally by
following the operating instructions. Adjust only
those controls that are covered by the operating
instructions as an improper adjustment of other
controls may result in damage and will often
require extensive work by a qualified technician
to restore the product to its normal operation,
e) If the product has been dropped or damaged in
any way, and
f) When the product exhibits a distinct change in
performance - this indicates a need for service.
19) Replacement Parts - When replacement parts are
required, be sure the service technician has used
replacement parts specified by the manufacturer or
have the same characteristics as the original part.
Unauthorized substitutions may result in fire, electric
shock, or other hazards.
20) Safety Check - Upon completion of any service or
repairs to this product, ask the service technician to
perform safety checks to determine that the product is
in proper operating condition.
21) Wall or ceiling mounting - When mounting the product
on a wall or ceiling, be sure to install the product
according to the method recommended by the
manufacturer.
22) Power Lines - An outside antenna system should not
be located in the vicinity of overhead power lines or
other electric light or power circuits, or where it can
fall into such power lines or circuits. When installing
an outside antenna system, extreme care should
be taken to keep from touching such power lines or
circuits as contact with them might be fatal.
23) Protective Attachment Plug - The product is equipped
with an attachment plug having overload protection.
This is a safety feature. See Instruction Manual
for replacement or resetting of protective device.
If replacement of the plug is required, be sure the
service technician has used a replacement plug
specified by the manufacturer that has the same
overload protection as the original plug.
24) Stand - Do not place the product on an unstable
cart, stand, tripod or table. Placing the product on an
unstable base can cause the product to fall, resulting
in serious personal injuries as well as damage to the
product. Use only a cart, stand, tripod, bracket or
table recommended by the manufacturer or sold with
the product. When mounting the product on a wall,
be sure to follow the manufacturer’s instructions. Use
only the mounting hardware recommended by the
manufacturer.
E-2
XL-DH229P_USA_EN.indd 2
12/28/2010 3:23:54 PM
For U.S. customer only
CONSUMER LIMITED WARRANTY
SHARP ELECTRONICS CORPORATION warrants to the first consumer purchaser that this Sharp brand product (the
"Product"), when ship in its original container, will be free from defective workmanship and materials, and agrees that it will,
at its option, either repair the defect or replace the defective Product or part thereof with a new or remanufactured equivalent
at no charge to the purchaser for parts or labor for the period(s) set forth below.
This warranty does not apply to any appearance items of the Product nor to the additional excluded item(s) set forth below
nor to any Product the exterior of which has been damaged or defaced, which has been subjected to improper voltage or
other misuse, abnormal service or handling, or which has been altered or modified in design or construction.
In order to enforce the rights under this limited warranty, the purchaser should follow the steps set forth below and provide
proof of purchase to the servicer.
The limited warranty described herein is in addition to whatever implied warranties may be granted to purchasers by law.
ALL IMPLIED WARRANTIES INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR USE ARE
LIMITED TO THE PERIOD(S) FROM THE DATE OF PURCHASE SET FORTH BELOW. Some states do not allow
limitations on how long an implied warranty lasts, so the above limitation may not apply to you.
Neither the sales personnel of the seller nor any other person is authorized to make any warranties other than those
described herein, or to extend the duration of any warranties beyond the time period described herein on behalf of Sharp.
The warranties described herein shall be the sole and exclusive warranties granted by Sharp and shall be the sole and
exclusive remedy available to the purchaser. Correction of defects, in the manner and for the period of time described
herein, shall constitute complete fulfillment of all liabilities and responsibilities of Sharp to the purchaser with respect to the
Product, and shall constitute full satisfaction of all claims, whether based on contract, negligence, strict liability or otherwise.
In no event shall Sharp be liable, or in any way responsible, for any damages or defects in the Product which were caused
by repairs or attempted repairs performed by anyone other than an authorized servicer. Nor shall Sharp be liable or in any
way responsible for any incidental or consequential economic or property damage. Some states do not allow the exclusion
of incidental or consequential damages, so the above exclusion may not apply to you.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY
FROM STATE TO STATE.
Model Specific Section
Your Product Model Number & Description:
XL-DH229P MICRO COMPONENT SYSTEM
(Be sure to have this information available when you need
service for your Product.)
Warranty Period for this Product:
One (1) year parts and labor from the date of purchase.
Additional Item(s) Excluded from Warranty Coverage
(if any):
Non-functional accessories, supplies, and consumable
items.
Where to Obtain Service:
At a Sharp Authorized Servicer located in the United States.
To find a location of the nearest Sharp Authorized Servicer,
call Sharp toll free at 1-800-BE-SHARP.
What to do to Obtain Service:
Ship prepaid or carry in your Product to a Sharp Authorized
Servicer. Be sure to have Proof of Purchase available. If
you ship the Product, be sure it is insured and packaged
securely.
TO OBTAIN SUPPLY, ACCESSORY OR PRODUCT INFORMATION, CALL 1-800-BE-SHARP
SHARP ELECTRONICS CORPORATION
Sharp Plaza, Mahwah, New Jersey 07495-1163
System connections
Q Precautions
O
Please ensure that the equipment is positioned in a well ventilated area
and ensure that there is at least 4" (10 cm) of free space along the sides,
top and back of the equipment.
4" (10 cm) 4" (10 cm)
4" (10 cm)
M I C RO C O M P O N E N T S Y S T E M
XL-DH229
O
O
O
O
4" (10 cm)
Use the unit on a firm, level surface free from vibration.
Place the speakers at least 12" (30 cm) away from any CRT TV to avoid
color variations across the TV screen. If the variations persist, move
the speakers further away from the TV. LCD TV is not prone to such
variation.
Keep the unit away from direct sunlight, strong magnetic fields, excessive
dust, humidity and electronic/electrical equipment (home computers,
facsimiles, etc.) which generate electrical noise.
Do not place anything on top of the unit.
XL-DH229P_USA_EN.indd 3
O
Do not expose the unit to moisture, to temperatures higher than 140˚F
(60˚C) or to extremely low temperatures.
If your system does not work properly, disconnect the AC power cord
from the AC outlet. Plug the AC power cord back in, and then turn on
your system.
O In case of an electrical storm, unplug the unit for safety.
O Hold the AC power plug by the head when removing it from the AC outlet,
as pulling the cord can damage internal wires.
O The AC power plug is used as a disconnect device and shall always
remain readily operable.
O Do not remove the outer cover, as this may result in electric shock.
Refer internal service to your local SHARP service facility.
O This unit should only be used within the range of 41˚F - 95˚F
(5˚C - 35˚C).
Warning:
The voltage used must be the same as that specified on this unit. Using this
product with a higher voltage other than that which is specified is dangerous
and may result in a fire or other type of accident causing damage. SHARP will
not be held responsible for any damage resulting from use of this unit with a
voltage other than that which is specified.
O
E-3
12/28/2010 3:23:54 PM
System connections (continued)
Make sure to unplug the AC power cord before making any connections.
Video cable
(not supplied)
TV
To video input jack
LEFT
Wire
RIGHT
AM loop
antenna
SPEAKERS
Installing the AM loop
antenna
< Assembling >
FM antenna
External FM antenna
for better reception
(not supplied)
< Attaching to
the wall >
Wall
Plug in with the
lever side facing
to the left.
Screws
(not supplied)
AC outlet
(AC 120 V ~ 60 Hz)
Q Volume control
The sound level at a given volume setting depends on
speaker efficiency, location, and various other factors. It is
advisable to avoid exposure to high volume levels, which
occurs while turning the unit on with the volume control
setting up high, or while continually listening at high
volumes. Excessive sound pressure from earphones and
headphones can cause hearing loss.
Q Speaker connection
O Use speakers with an impedance of 4 ohms or more,
as lower impedance speakers can damage the unit.
O Do not make a mistake when connecting the right and
left speakers. The right speaker is the one on the right
side when you face the unit.
O Insert the speaker plug fully with the lever side facing
to the left.
O Hold the speaker plug when removing it from the unit.
Pulling the wire may cause malfunction to the unit.
O Do not allow any objects to fall into or to be placed in
the bass reflex ducts.
O Do not stand or sit on the speakers. You may be
injured.
Remote control
Q Battery installation
Use 2 “AAA” size batteries (UM/SUM-4, R3, HP-16 or
similar). Batteries are not included.
Plastic film covering can be removed or peeled off.
1 Open the battery cover.
2 Insert the batteries according to the direction indicated
in the battery compartment.
When inserting or removing the batteries, push them
toward the battery terminals.
3 Close the battery cover.
Caution:
O Replace all old batteries with new ones at the same time.
O Do not mix old and new batteries.
O Remove the batteries if the unit will not be used for a long
period of time. This will prevent potential damage due to
battery leakage.
O Do not use rechargeable batteries (nickel-cadmium battery,
etc.).
O Installing the batteries incorrectly may cause the unit to
malfunction.
O Batteries (battery pack or batteries installed) shall not be
exposed to excessive heat such as sunshine, fire or the like.
E-4
XL-DH229P_USA_EN.indd 4
12/28/2010 3:23:54 PM
Q Auto power on function
Remote control (continued)
Notes concerning use:
O Replace the batteries if the operating distance is
reduced or if the operation becomes erratic.
O Periodically clean the transmitter on the remote control
and the sensor on the unit with a soft cloth.
O Exposing the sensor on the unit to strong light may
interfere with operation. Change the lighting or the
direction of the unit.
O Keep the remote control away from moisture, heat,
shock, and vibrations.
General control
When you press any of the following buttons, the unit turns on.
O iPod® / iPhone, CD, USB, AUDIO IN, TUNER (BAND)
on the remote control: Selected function is activated.
O
button on the main unit: The unit turns on and
playback of the last function will start (CD, TUNER,
USB, iPod, AUDIO IN).
Q Auto power off function
The main unit will enter the stand-by mode (when iPod/
iPhone is not docked) after 15 minutes of inactivity during:
iPod/iPhone: No connection.
AUDIO IN: No detection of input signal or very low sound
audibility.
TUNER: No reception of broadcast signal.
CD / USB: In the stop mode.
Note:
However, if iPod/iPhone is docked, the unit will begin charging.
“CHARGE MODE” will be displayed.
Q Muting
The volume is muted temporarily when pressing the MUTE
button on the remote control. Press again to restore the volume.
Q X-Bass control
When the power is first turned on, the unit will enter the
extra bass mode which emphasizes the bass frequencies,
and “X-BASS” will appear. To cancel the extra bass mode,
press the X-BASS button on the remote control.
Q Bass control
1 Press the BASS/TREBLE button to select “BASS”.
2 Within 5 seconds, press the VOLUME (+ or -) button
to adjust the bass.
Q To turn the power on
The first time the unit is plugged in, the unit will enter the
demonstration mode.
Function
Main unit
Remote
control
Power on/
off
Demo on/
off
1 Press the BASS/TREBLE button to select “TREBLE”.
2 Within 5 seconds, press the VOLUME (+ or -) button to
Operation
Press to turn the
power on or to
go to stand-by
mode.
____
Q Treble control
Press to enter to
demonstration on
or off mode.
Q Display brightness control
To dim the display brightness, press the DEMO/DIMMER
button on the remote control.
Q Volume auto fade-in
If you turn off and on the main unit with the volume set to
27 or higher, the volume starts at 16 and fades in to the
last set level.
Q Volume control
Turn the volume knob toward VOL +/- (on main unit) or
press VOLUME +/- (on remote control) to increase or
decrease the volume.
adjust the treble.
Q Equalizer
When
the
EQUALIZER
MODE button is pressed,
the current mode setting will
be displayed. To change to
a different mode, press the
EQUALIZER MODE button
repeatedly until the desired
sound mode appears.
FLAT
GAME
Equalizer off.
For game.
CLASSIC For classical music.
POPS
For pop music.
VOCAL
Vocals are enhanced
JAZZ
For jazz.
Q Function
When the FUNCTION button on main unit is pressed, the
current function will change to different mode. Press the
FUNCTION button repeatedly to select desired function.
CD
FM STEREO
FM MONO
AM
iPod
USB
AUDIO IN
Note:
The backup function will protect the memorized function
mode for a few hours should there be a power failure or
the AC power cord becomes disconnected.
E-5
XL-DH229P_USA_EN.indd 5
12/28/2010 3:23:55 PM
Listening to the iPod or iPhone
iPhone and iPod operations
Made for:
O iPhone 3GS
O iPhone 3G
O iPhone
O iPod touch (3rd generation)
O iPod touch (2nd generation)
O iPod touch (1st generation)
O iPod classic
O iPod with video
O iPod nano (5th generation)
O iPod nano (4th generation)
O iPod nano (3rd generation)
O iPod nano (2nd generation)
O iPod nano (1st generation)
O iPod with color display
O iPod mini
Caution:
Please update your iPod unit to the latest software version
from Apple’s homepage before using it.
Notes:
O Once the iPod or iPhone is connected to the unit it will
begin charging.
O The message “This accessory is not made to work with
iPhone” or similar, may appear on the iPhone screen
when:
- battery is low.
- the iPhone is not properly docked (eg. slanting).
If this occurs, remove and re-dock the iPhone.
O This product is made for iPhone. To prevent
random interference when iPhone is docked, the
headphone output is disabled, and “HP INVALID”
will be displayed. You may also experience brief
audio interference during incoming calls.
Q iPod and iPhone adaptor connection
Notes:
O Please use the adaptor supplied with your iPod or
iPhone unit.
O You can use an audio cable to connect your iPod to the
AUDIO IN jack if:
1. your iPod adaptor does not fit into the iPod dock on
the main unit.
2. you have an iPod that does not have an iPod
adaptor.
3. you have an iPod that does not have an iPod 30 pin
connector.
iPhone
Adaptor No.
iPhone
Description
Q To insert iPod or iPhone adaptor
1 Open the iPod cover by pulling up the tip.
2 Insert the iPod or iPhone adaptor into unit and
connect your iPod or iPhone.
iPhone (bottom)
iPhone
Dock connector
iPhone adaptor
iPhone dock
iPhone connector
Caution:
Unplug all accessories from the iPod or iPhone before
inserting it into the dock.
Q To remove iPod or iPhone adaptor
Insert the tip of a screwdriver (“-” type,
small) into the adaptor hole as shown
and lift upward to remove.
Q iPod or iPhone playback
1 Press the ON/STAND-BY button to turn the power on.
2 Press the iPod/iPhone button on the remote control
or FUNCTION button repeatedly on the main unit to
select iPod function.
3 Insert iPod or iPhone unit in iPod dock of main unit.
“DOCK OK” will be displayed for 3 seconds.
4 Press the
(iPod/iPhone
) button to start
playback.
Q iPhone playback
Capacity
12
iPhone
15
iPhone 3G
8GB & 16GB
15
iPhone 3GS
16GB & 32GB
4GB & 8GB & 16GB
O Sound will only switch from iPhone to the main unit after
authentication process is completed in approximately 10
seconds.
O Incoming calls will pause the playback and iPhone
ringtones will be heard from the main unit speakers only.
O Once the calls are answered, the conversation can
only be heard through the built-in iPhone speaker. Turn
on the iPhone speaker or undock the iPhone to start
conversation.
Q To disconnect iPod or iPhone
Simply remove the iPod or iPhone from the iPod dock. It is
safe to do so even during playback.
E-6
XL-DH229P_USA_EN.indd 6
12/28/2010 3:23:55 PM
Listening to the iPod or iPhone
(continued)
Q Various iPod functions
Function
Q Navigating the iPod and iPhone menus
Main
unit
unit. Press it again to go back to previous menu.
or ) button to select an item on the
menu and then press ENTER button.
Note:
When navigating the iPod or iPhone menu with remote control,
do not operate any of the buttons on the iPod or iPhone unit. The
volume level is adjusted by pressing the VOL (+ or -) button on
the main unit or the remote control. Adjusting the volume on the
iPod and iPhone units give no effect.
Press in the pause
mode.
Pause
Press in the playback
mode.
Track
up/down
Press in the playback
or pause mode. If you
press the button in the
pause mode, press the
button to start the
desired track.
Press and hold down in
the playback mode.
Release the button to
resume playback.
____
Fast
forward/
reverse
iPod and iPhone operations:
The operations described below depend on the generation iPod
and iPhone you are using.
____
iPod back light ON.
Press for more than
2 seconds to toggle
the video out display
between iPod or TV.
Press to toggle repeat
mode.
____
Press and hold down to
toggle shuffle mode.
____
Repeat
Shuffle
Q Watching videos on a TV connected to iPod
or iPhone
1 Press the DISPLAY (TV OUT) button for more than 2
seconds. “TV DISP” will appear on display.
2 Press the ENTER button to start playback.
Notes:
O If the TV Out setting is already turned on at video menu,
the video is automatically displayed on the TV screen when
ENTER key is pressed.
O To return to watching video on iPod or iPhone screen, press
the MENU button to enter video menu. Then press the
DISPLAY (TV OUT) button for more than 2 seconds until
“iPod DISP” appears.
O During iPod or iPhone video playback, pressing the DISPLAY
(TV OUT) button will not toggle video out display between
iPod and TV.
iPod or iPhone playback detection function:
Once the play button on the iPod or iPhone unit is pressed,
the main unit will automatically change to iPod function
overriding the previous function selected.
Caution:
O Unplug all accessories for the iPod or iPhone before inserting
it into the iPod dock.
O Stop button ( ) at main unit is invalid during iPod function.
____
Display
System on operation:
When the main unit is powered on, the iPod and iPhone units will
automatically power on when docked in the unit.
System off (stand-by operation):
When the main unit is turned to stand-by mode, the docked iPod
and iPhone unit will automatically turn to stand-by mode.
Operation
Play
1 Press the MENU button to view the menu on iPod or iPhone
2 Use the PRESET (
Remote
control
iPod
Menu
____
iPod
Enter
____
Press to view the iPod
menu during iPod
function.
Press to confirm the
selection.
iPod
Cursor
Up/Down
____
Press to select the iPod
menu.
Listening to a CD or MP3/WMA disc
Q Disc playback
1 Press the ON/STAND-BY button to turn the power on.
2 Press the CD button on the remote control or
3
4
5
6
FUNCTION button repeatedly on the main unit to
select CD function.
Press the OPEN/CLOSE button to open the disc tray.
Place the disc on the disc tray, label side up.
Press the OPEN/CLOSE button to close the disc tray.
Press the
(CD/USB
) button to start playback.
After the last track is played, the unit will stop
automatically.
Notes for CD or MP3/WMA disc:
O When the end of the last track is reached during fast
forward, “END” will appear on the display and CD
operation will be paused. When the beginning of the
first track is reached during fast reverse, the unit will
enter the playback mode (only for CD).
O Rewritable multi-session discs with unfinished writing,
can still be played.
E-7
XL-DH229P_USA_EN.indd 7
12/28/2010 3:23:55 PM
Q Repeat play
Listening to a CD or MP3/WMA disc
(continued)
Repeat play can play one track, all tracks or a programed
sequence continuously.
Q Various disc functions
Function
Main
unit
Remote
control
Operation
Play
Press in the stop mode.
Stop
Press in the playback
mode.
Pause
Press in the playback
mode. Press the
button to resume playback
from the paused point.
Press in the playback or
stop mode.
If you press the button in
the stop mode, press the
button to start the
desired track.
Press and hold down in the
playback mode.
Release the button to
resume playback.
Track up/
down
____
Fast
forward/
reverse
____
To repeat one track:
Press the PLAY MODE button repeatedly until “1-REPEAT”
(CD/USB
) button.
appears. Press the
To repeat all tracks:
Press the PLAY MODE button repeatedly until “ALL
(CD/USB
) button.
REPEAT” appears. Press the
To repeat desired tracks:
Perform steps 1 - 5 in “Programed play” section and
then press the PLAY MODE button repeatedly until “ALL
REPEAT” appears.
To cancel repeat play:
Press the PLAY MODE button repeatedly until “NORMAL”
” disappears.
appears and “
Q Random play
The tracks on the disc can be played in random order
automatically.
To random play all tracks:
Press and hold down PLAY MODE button on the remote
(CD/USB
control until “RANDOM” appears. Press the
) button.
Advanced CD or MP3/WMA disc playback
To cancel random play:
Press the PLAY MODE button until “NORMAL” appears
and “R” disappears.
RRMCGA232AWSA
Q Direct track search
By using the Numeric buttons, the desired tracks on the
current disc can be played.
Use the Numeric buttons on the remote control to select
the desired track while playing the selected disc.
O The Numeric buttons allow you to select up to number 9.
O When selecting number 10 or higher, use the “10+”
button.
A. For example, to choose 13
1 Press the “10+” button once.
2 Press the “1” button.
3 Press the “3” button.
Selected track
B. For example, to choose 130
1 Press the “10+” button twice.
2 Press the “1” button.
3 Press the “3” button.
4 Press the “0” button.
number
Notes:
O If you press the
button during random play, you can move
to the track selected next by the random operation. On the
other hand, the
button does not allow you to move to
the previous track. The beginning of the track being played
will be located.
O In random play, the unit will select and play tracks
automatically. (You cannot select the order of the tracks.)
Caution:
After performing repeat play, be sure to press the (CD/
USB ) button. Otherwise, the disc will play continuously.
Q Programed play (CD)
You can choose up to 32 selections for playback in the
order you like.
1 While in the stop mode, press the MEMORY button on the
remote control to enter the programing save mode.
2 Press the
Notes:
O A track number higher than the number of tracks on the
disc cannot be selected.
O During random play, direct search is not possible.
To stop playback:
Press the (CD/USB ) button.
or
buttons on the remote control to
select the desired track.
Selected track number
E-8
XL-DH229P_USA_EN.indd 8
12/28/2010 3:23:55 PM
Q Procedure to playback MP3/WMA disc
with folder mode on
Advanced CD or MP3/WMA disc
playback (continued)
To play back CD-R/RW.
3 Press the MEMORY button to save the track number.
4 Repeat steps 2 - 3 for other tracks. Up to 32 tracks
1 Press the CD button, and load an MP3/WMA disc. Press
the FOLDER button and disc info will be displayed.
MP3 indicator
Disc
WMA indicator
Name
can be programed. If you want to check the programed
tracks, press the MEMORY button repeatedly. If you
make a mistake, the programed tracks can be cleared
by pressing the CLEAR button.
5 Press the
(CD/USB
) button to start playback.
TOTAL indicator
Q Programed play (MP3/WMA)
Total number of folder
Total number of files
2 Press the FOLDER button, and press the PRESET ( or )
button to select desired playback folder. (Folder mode on)
FOLDER
indicator
1 While in the stop mode, press the MEMORY button to
enter the programing save mode.
2 Press the PRESET (
3
4
Then press the
or
button on the remote control
to select the desired tracks.
3 Press the MEMORY button to save the folder and track
number.
4 Repeat steps 2 - 3 for other folder/tracks. Up to 32
tracks can be programed.
5 Press the
(CD/USB
First track number in
the folder
Select desired file to be played back by pressing the
or
button.
(CD/USB
) button. Playback will start and
Press the
file name will be displayed.
O Title, Artist and Album name are displayed if they are
recorded on the disc.
O In case of playback with the folder mode on, press
the PRESET ( or ) button, and the folder can be
selected even though it is in playback/pause mode. It
will continue playback/pause mode in the 1st track of the
selected folder.
O Display content can be changed by pressing the
DISPLAY button.
FOLDER number
or
) button on the remote
control to select the desired folder.
) button to start playback.
To cancel the programed play mode:
During programed stop mode, press the (CD/USB )
button. The display will show “MEM CLEAR” and all the
programed contents will be cleared.
Adding tracks to the program:
If a program has been previously stored, the “MEMORY”
indicator will be displayed. Press the MEMORY button
repeatedly to go to the last program memory. Then follow
steps 2 - 3 to add tracks. The new tracks will be stored after
the last track of the previous program.
File name display
Title display
Album display
Artist display
Note:
If “NO SUPPORT” is displayed, it means “Copyright protected
WMA file” or “Not supported playback file” is selected.
Listening to USB mass storage
device/MP3 player
Notes:
O When a disc is ejected, the program is automatically
canceled.
O If you press the ON/STAND-BY button to enter the standby mode or change the function from CD to another, the
programed selections will be cleared.
O During the program operation, random play is not possible.
Note:
This product is not compatible with MTP and AAC file
systems from USB mass storage device or MP3 player.
E-9
XL-DH229P_USA_EN.indd 9
12/28/2010 3:23:55 PM
Listening to USB mass storage device/
MP3 player (continued)
Q To play back USB/MP3 player with folder
mode off
1 Press the USB button on the remote control or
FUNCTION button repeatedly on main unit to select
USB function. Connect the USB memory device that
has MP3/WMA format files on the unit. When the USB
memory is connected to the main unit, the device
information will be displayed.
2 Select desired file to be played back by pressing the
or
button.
3 Press the
(CD/USB
) button. Playback will
start and the file name will be displayed.
O Title, Artist and Album name are displayed if they
are recorded in the USB memory device.
O Display content can be changed by pressing the
DISPLAY button.
Note:
To pause playback:
(CD/USB
Press the
) button.
Q To play back USB/MP3 player with folder
mode on
O USB cable is not recommended for use in this audio
system to connect to USB memory device. Use of the
USB cable will affect the performance of this audio
system.
O This USB memory cannot be operated via USB hub.
O The USB terminal in this unit is not intended for a PC
connection but is used for music streaming with a USB
memory device.
O External HDD-storage cannot be played back via USB
terminal.
O If the data inside the USB memory is large, it may take
longer time for the data to be read.
O This product can play WMA and MP3 files. It will
automatically detect the file type being played. If
unplayable file is played on this product, “NO SUPPORT”
is indicated and the file will be automatically skipped.
This will take a few seconds. If abnormal indications
appear on the display due to the unspecified file, turn
off the unit and then turn it on again.
O This product relates to USB mass storage devices and
MP3 players. It may however face some irregularities
due to various unforeseen reasons from some devices.
Should this happen, turn off the unit and then turn it
on again.
O The USB port is only intended for direct connection to
a USB memory device without any cable.
O During CD function, MP3 player will not be charging.
1 Press the USB button on the remote control or
FUNCTION button repeatedly on main unit to select
USB function. Connect the USB memory device that
has MP3/WMA format files on the unit. When the USB
memory is connected to the main unit, the device
information will be displayed.
2 Press the FOLDER button, and press the PRESET
( or ) button to select desired playback folder. To
start playback with folder mode on, go to step 4. To
change the playback folder, press the PRESET ( or
) button to select another folder.
3 Select desired file to be played back by pressing the
or
button.
4 Press the
(CD/USB
) button. Playback will
start and the file name will be displayed.
O Title, Artist and Album name are displayed if they
are recorded in the USB memory device.
O Display content can be changed by pressing the
DISPLAY button.
Q To remove USB memory device
1 Press the (CD/USB ) button to stop playback.
2 Disconnect USB memory device from the USB
terminal.
Notes:
O SHARP will not be held liable for the loss of data while
the USB memory device is connected to the audio
system.
O Files compressed in MP3 and/or WMA format can be
played back when connected to the USB terminal.
O This USB memory’s format supports FAT 16 or FAT
32.
O SHARP cannot guarantee that all USB memory
devices will work on this audio system.
Advanced USB playback
The following functions are the same as CD
operations:
Page
Direct track search ........................................................ 8
Repeat play .................................................................... 8
Random play .................................................................. 8
Programed play...........................................................8-9
Note:
If USB memory device is not connected, “NO MEDIA” will
be shown on the display.
Notes:
O This unit only supports “MPEG-1 Audio Layer-3”
format. (Sampling Frequency is 32, 44.1, 48kHz)
O Playback order for MP3 files may differ depending on
the writing software used during file download.
O Bitrate which is supported by MP3 is 32~320 kbps,
WMA is 64~160 kbps.
O For MP3/WMA files, please put “.MP3” “.WMA”
extension. Files cannot be played back if there is no
MP3/WMA extension.
O Playlists are not supported on this unit.
O This unit can display Folder Name or File Name up to
32 characters.
O Maximum total number of MP3/WMA files is 1024.
Maximum total number of folders is 255 inclusive of
root directory.
O The display playback time may not be displayed
correctly when playing back a variable bitrate file.
O The ID3TAG information supported are TITLE, ARTIST
and ALBUM only. Title name, artist name and album
name can be displayed by pressing the DISPLAY
button during file playback or pause mode.
O WMA meta tag also supports title, artist and album
name which are recorded in WMA files. Copyright
protected WMA files cannot be played back.
E-10
XL-DH229P_USA_EN.indd 10
12/28/2010 3:23:55 PM
4 Within 30 seconds, press the MEMORY button to store
Listening to the radio
that station in memory. If the “MEMORY” and preset
number indicators disappear before the station is
memorized, repeat the operation from step 2.
5 Repeat steps 1 - 4 to set other stations, or to change
a preset station. When a new station is stored in the
memory, the station previously memorized for that
preset channel number will be erased.
Note:
The backup function protects the memorized stations for a few
hours should there be a power failure or the AC power cord
become disconnected.
Q To recall a preset station
1 Press the PRESET (
or ) button for less than 0.5
seconds to select the desired station.
Q To scan the preset stations
The stations saved in the memory can be scanned
automatically. (Preset memory scan)
1 Press the PRESET (
Q Tuning
1 Press the ON/STAND-BY button to turn the power on.
2 Press the FUNCTION button on the main unit
or TUNER (BAND) button on the remote control
repeatedly to select the desired frequency band (FM
stereo, FM mono or AM).
3 Press the TUNING ( or ) (TUNING (
or
))
button to tune in to the desired station.
O Manual tuning:
or
))
Press the TUNING ( or ) (TUNING (
button repeatedly to tune in to the desired station.
O Auto tuning:
or
))
When the TUNING ( or ) (TUNING (
button is pressed for more than 0.5 seconds, scanning
will start automatically and the tuner will stop at the first
receivable broadcast station.
Notes:
O When radio interference occurs, auto scan tuning may
stop automatically at that point.
O Auto scan tuning will skip weak signal stations.
O To stop the auto tuning, press the TUNING ( or )
or
)) button again.
(TUNING (
To receive an FM stereo transmission:
O Press the FUNCTION button on main unit or TUNER (BAND)
button on the remote control to select stereo mode and “ST”
indicator will be displayed. “ ” will appear when an FM
broadcast is in stereo.
O If the FM reception is weak, press the TUNER (BAND) button
to extinguish the “ST” indicator. The reception changes to
monaural, and the sound becomes clearer.
Q Presetting a station
or
) button for more than
0.5 seconds. The preset number will flash and the
programed stations will be tuned in sequentially, for 5
seconds each.
2 Press the PRESET ( or ) button again when the
desired station is located.
Q To erase entire preset memory
1 Press the POWER ON/STAND-BY button to enter the standby mode.
2 While pressing down the FUNCTION button, press the POWER
ON/STAND-BY button until “TUNER CLEAR” appears.
Setting the clock (Remote control only)
In this example, the clock is set for the 12-hour (AM 12:00) display.
1 Press the ON/STAND-BY button to turn the power on.
2 Press the CLOCK/TIMER button.
3 Within 10 seconds, press the MEMORY button. Press
the
or
button to select 12-hour or 24-hour display
and then press the MEMORY button.
The 12-hour display will appear.
(AM 12:00 - PM 11:59)
You can store 40 AM and FM stations in memory and
recall them at the push of a button. (Preset tuning)
1 Perform steps 1 - 3 in “Tuning”.
2 Press the MEMORY button.
3 Within 30 seconds, press the PRESET (
The 12-hour display will appear.
(AM 0:00 - PM 11:59)
or ) button
to select the preset channel number. Store the stations
in memory, in order, starting with preset channel 1.
The 24-hour display will appear.
(0:00 - 23:59)
4 To adjust the hour, press the
or
button and then
or
button
press the MEMORY button. Press the
once to advance the time by 1 hour. Hold it down to
advance continuously.
E-11
XL-DH229P_USA_EN.indd 11
12/28/2010 3:23:55 PM
Setting the clock (continued)
5 To adjust the minutes, press the
or
button and
or
then press the MEMORY button. Press the
button once to advance the time by 1 minute.
To confirm the time display:
Press the CLOCK/TIMER button. The time display will
appear for about 5 seconds.
When you select the tuner, select a station by pressing the
or
button, and then press the MEMORY button. If
a station has not been programmed, “NO PRESET” will be
displayed and timer setting will be cancelled.
9 Adjust the volume using the VOLUME control, and then press
the MEMORY button. Do not turn the volume up too high.
10 Press the ON/STAND-BY button to enter the power stand-by
mode. The “TIMER” indicator lights up and the unit is ready
for timer playback.
Note:
The “CLOCK” will appear or time will be displayed when the AC
power supply is restored after a power failure or unplugging the
unit. If incorrect, readjust the clock as follows.
To readjust the clock:
Perform “Setting the clock” from step 1. If the “CLOCK” does not
appear in step 2, step 3 (for selecting the 24-hour or 12-hour
display) will be skipped.
To change the 24-hour or 12-hour display:
1 Clear all the programed contents. [Refer to “Factory reset,
clearing all memory” on page 14 for details.]
2 Perform “Setting the clock” from step 1 onwards.
Timer and sleep operation (Remote
control only)
Once timer:
Once timer play works for one time only at a preset time.
Daily timer:
Daily timer play works at the same preset time every day that we
set. For example, set the timer as a wake-up call every morning.
Using the once timer and daily timer in combination:
For example, use the once timer to listen a radio program, and
use the daily timer to wake up.
1 minute or more
Daily timer
Start
Once timer
Stop
Start
Stop
Q Timer playback
Before setting timer:
O Check that the clock is set to the correct time (refer to
page 11-12). If it is not set, you cannot use the timer
function.
O For timer playback: Plug in USB or load discs or dock iPod
to be played.
1 Press the ON/STAND-BY button to turn the power on.
2 Press and hold the CLOCK/TIMER button.
3 Within 10 seconds, press the
or
button to select
4
5
6
7
8
“ONCE SET” or “DAILY SET”, and press the MEMORY
button. Set the clock to the correct time if “ONCE SET” or
“DAILY SET” does not appear.
Within 10 seconds, press the
or
button to select
“TIMER SET”, and press the MEMORY button.
To adjust the hour, press the
or
button and then press
the MEMORY button.
or
button and then
To adjust the minutes, press the
press the MEMORY button.
Set the time to finish as in steps 5 and 6 above.
To select the timer playback source (CD, TUNER, USB,
iPodor AUDIO IN), press the
or
button. Press the
MEMORY button.
11 When the preset time is reached, playback will start. The
volume will increase gradually until it reaches the preset
volume. The “ ” indicator will blink during once timer
playback. The “DAILY” indicator will blink during daily timer
playback.
12 When the timer end time is reached, the system will enter the
power stand-by mode automatically.
Once timer:
The timer will be cancelled.
Daily timer:
The timer operates at the same time every day. It will continue
until the daily timer setting is cancelled. Cancel the daily timer
when it is not in use.
Notes:
O When performing timer playback using another unit
connected to the USB terminal or AUDIO IN socket, select
“USB” or “AUDIO IN” in step 8.
O This unit will turn on or enter the power stand-by mode
automatically. However, the connected unit will not turn on
or off. To stop the timer playback, follow step “Cancelling the
timer setting” of this page.
Checking the timer setting:
1 Turn the power on and press and hold down the CLOCK/
TIMER button.
2 Within 10 seconds, press the
or
button to select
“ONCE SET” or “DAILY SET”, and press the MEMORY
button.
3 Within 10 seconds, press the
or
button to select
“TIMER CALL”, and press the MEMORY button.
Canceling the timer setting:
1 Turn the power on and press and hold down the CLOCK/
TIMER button.
2 Within 10 seconds, press the
or
button to select
“ONCE SET” or “DAILY SET”, and press the MEMORY
button.
3 Within 10 seconds, press the
or
button to select
“TIMER OFF”, and press the MEMORY button. Timer will be
canceled (the setting will not be canceled).
Reusing the memorized timer setting:
The timer setting will be memorized once it is entered. To reuse
the same setting, perform the following operations.
1 Turn the power on and press and hold down the CLOCK/
TIMER button.
2 Within 10 seconds, press the
or
button to select
“ONCE SET” or “DAILY SET”, and press the MEMORY
button.
3 Within 10 seconds, press the
or
button to select
“TIMER ON”, and press the MEMORY button.
4 Press the ON/STAND-BY button to enter the power standby mode.
E-12
XL-DH229P_USA_EN.indd 12
12/28/2010 3:23:55 PM
Timer and sleep operation
(Remote control only) (continued)
Enhancing your system
The connection cord is not included. Purchase a commercially
available cord as shown below.
Q Sleep operation
Portable
audio
player, etc.
The radio, compact disc, iPod and USB can all be turned
off automatically.
1 Play back the desired sound source.
2 Press the SLEEP button.
3 Within 10 seconds, press the SLEEP button repeatedly
to select the time.
10
20
30 ....... 80
90
Audio cable
(not supplied)
4 “SLEEP” will appear.
5 The unit will enter the power stand-by mode
automatically after the preset time has elapsed. The
volume will be turned down 1 minute before the sleep
operation finishes.
To confirm the remaining sleep time:
1 While “SLEEP” is indicated, press the SLEEP button.
M I C RO C O M P O N E N T S Y S T E M
XL-DH229P
To cancel the sleep operation:
Press the ON/STAND-BY button while “SLEEP” is
indicated. To cancel the sleep operation without setting
the unit to the stand-by mode, proceed as follows.
1 While “SLEEP” is indicated, press the SLEEP button.
2 Within 10 seconds, press the SLEEP button repeatedly
to select “SLEEP 00”.
Q To use timer and sleep operation together
Sleep and timer playback:
For example, you can fall asleep listening to the radio and
wake up to CD in the next morning.
1 Set the sleep time (see above, steps 1 - 5).
2 While the sleep timer is set, set the timer playback
(steps 2 - 9, page 12).
Sleep timer setting
Timer playback setting
90 minutes
Sleep operation will
automatically stop
End time
Desired time
Timer playback start
time
Q Listening to the playback sounds of
portable audio player, etc.
1 Use a connection cord to connect the portable audio
player etc. to the AUDIO IN jack. When using video
equipment, connect the audio output to this unit and
the video output to a television.
2 Press the ON/STAND-BY button to turn the power on.
3 Press the AUDIO IN button on the remote control or
FUNCTION button repeatedly on main unit to select
AUDIO IN function.
4 Play the connected equipment. If volume level of the
connected device is too high, sound distortion may
occur. Should this happen, lower the volume of the
connected device. If volume level is too low, increase
the volume of the connected device.
Note:
To prevent noise interference, place the unit away from the
television.
Q Headphones
O Do not turn the volume on to full at switch on and listen
to music at moderate levels. Excessive sound pressure
from earphones and headphones can cause hearing
loss.
O Before plugging in or unplugging the headphone,
reduce the volume.
O Be sure your headphone has a 1/8" (3.5 mm) diameter
plug and impedance between 16 and 50 ohms. The
recommended impedance is 32 ohms.
O Plugging in the headphone disconnects the speakers
automatically. Adjust the volume using the VOLUME
control.
E-13
XL-DH229P_USA_EN.indd 13
12/28/2010 3:23:55 PM
Q iPod and iPhone
Troubleshooting chart
Many potential problems can be resolved by the owner without calling a
service technician.
If something is wrong with this product, check the following before calling your
authorized SHARP dealer or service center.
Q General
Symptom
O Did a power failure occur? Reset the
clock. (Refer page 11)
O When a button is
pressed, the unit does
not respond.
O Set the unit to the power stand-by
mode and then turn it back on.
O If the unit still malfunctions, reset it.
(Refer page 14)
O No sound is heard.
O Is the volume level set to “MIN”?
O Are the headphones connected?
O Are the speaker wires disconnected?
Q CD player
Symptom
Possible cause
O Playback does not start. O Is the disc loaded upside down?
O Playback stops in
O Does the disc satisfy the standards?
the middle or is not
O Is the disc distorted or scratched?
performed properly.
O Is the unit located near excessive
vibrations?
O Is the disc very dirty?
O Has condensation formed inside
the unit?
Q Remote control
Symptom
O The remote control
does not operate.
Possible cause
O Is the AC power cord of the unit
plugged in?
O Is the battery polarity correct?
O Are the batteries dead?
O Is the distance or angle incorrect?
O Does the remote control sensor
receive strong light?
Q Tuner
Symptom
O The radio makes
unusual noises
continuously.
Possible cause
O The iPod or iPhone is not playing.
O The iPod or iPhone is not properly
connected to the unit.
O Is the AC power cord of the unit
plugged in?
O The video cable is not properly
connected.
O The TV/monitor’s input selection is not
properly set.
O The iPod TV out feature has not been
set to output video.
O iPod or iPhone will not
charge.
O The iPod or iPhone is not making full
contact with the connector.
O Using iPod (3rd generation).
O The iPod or iPhone is not supported.
Refer to page 6 for compatible models.
O “This accessory is not
made to work with
iPhone” or similar,
appears on iPhone
screen.
O The iPhone battery is low. Please
charge the iPhone.
O iPhone is not properly docked.
Possible cause
O The clock is not set to
the correct time.
O Playback sounds are
skipped, or stopped in
the middle of a track.
Symptom
O No sound is produced.
No image appears on
the TV/monitor.
Possible cause
O Is the unit placed near the TV or
computer?
O Is the FM antenna or AM loop antenna
placed properly? Move the antenna
away from the AC power cord if it is
located nearby.
Q Condensation
Sudden temperature changes, storage or operation in an extremely humid
environment may cause condensation inside the cabinet (CD pickup, etc.) or
on the transmitter on the remote control. Condensation can cause the unit to
malfunction. If this happens, leave the power on with no disc in the unit until
normal playback is possible (about 1 hour). Wipe off any condensation on the
transmitter with a soft cloth before operating the unit.
Q If problem occurs during operation
When this product is subject to strong outdoor interference (mechanical
shock, excessive static electricity, abnormal supply voltage due to lightning,
etc.) or if it is operated incorrectly, it may malfunction.
If such a problem occurs, do the following:
1 Set the unit to the stand-by mode and turn the power on again.
2 If the unit is not restored in the previous operation, unplug and plug in the
unit again, and then turn the power on.
Note:
If neither operation above restores the unit, clear all the memory by resetting
it.
Q Factory reset, clearing all memory
1
2
Press the POWER ON/STAND-BY button to enter the power stand-by
mode.
While pressing down the OPEN/CLOSE button, press the POWER
ON/STAND-BY button until “ALL CLEAR” appears.
Q USB
Symptom
O Device cannot be
detected.
Possible cause
O
O
O
O
Is there any MP3/WMA file available?
Is the device properly connected?
Is it an MTP device?
Does the device contain AAC file only?
O Playback does not start. O Is it a copyright protected WMA file?
O Is it a false MP3 file?
O Wrong time display.
O Wrong file name
display.
O Is Variable Bitrate file being played
back?
O Is the File Name written in Chinese or
Japanese characters?
Caution:
This operation will erase all data stored in memory including clock, timer
settings, tuner preset, and CD program.
Q Before transporting the unit
Remove the iPod/iPhone, USB memory device and disc from the unit. Then,
set the unit to the power stand-by mode. Carrying the unit with iPod/iPhone or
USB memory device left docked or discs left inside might damage the unit.
E-14
XL-DH229P_USA_EN.indd 14
12/28/2010 3:23:55 PM
Troubleshooting chart (continued)
Q Amplifier
Q Care of compact discs
Output power
RMS: Total 100 watt (50 W per channel
into 4 ohms at 1 kHz, 10% Total
harmonic distortion.)
FTC: 37.5 watt minimum RMS per
channel into 4 ohms from 100 Hz
to 20 kHz, 10% Total harmonic
distortion.
Output terminals
Speakers: 4 ohms
20Hz - 20kHz
Video output: 1 Vp-p
Headphones: 16-50 ohms
(recommended: 32 ohms)
Input terminals
Audio In (audio signal):
250 mV/47 k ohms
Compact discs are fairly resistant to damage, however mistracking can occur
due to an accumulation of dirt on the disc surface. Follow the guidelines below
for maximum enjoyment from your CD collection and player.
O Do not write on either side of the disc, particularly the non-label side from
which signals are read. Do not mark this surface.
O Keep your discs away from direct sunlight, heat, and excessive
moisture.
O Always hold the CDs by the edges. Fingerprints, dirt, or water on the
CDs can cause noise or mistracking. If a CD is dirty or does not play
properly, clean it with a soft, dry cloth, wiping straight out from the center,
along the radius.
Maintenance
Q USB
Q Cleaning the CD pickup lens
In order to ensure proper operation of the CD player, preventative maintenance
(cleaning of the laser pickup lens) should be performed periodically. Lens
cleaners are commercially available. Contact your local CD software dealer
for options.
USB host interface
O
Complies with USB 1.1 (Full
Speed)/2.0 Mass Storage Class.
Support Bulk only and CBI protocol.
Support file
O
O
MPEG 1 Layer 3
WMA (Non DRM)
Bitrate support
O
O
MP3 (32 ~ 320 kbps)
WMA (64 ~ 160 kbps)
Other
O
Maximum total number of MP3/WMA
files is 1024.
Maximum total number of folders is
255 INCLUSIVE of root directory.
The ID3TAG information supported
are TITLE, ARTIST and ALBUM
only.
Supports ID3TAG version 1 and
version 2.
Q Cleaning the cabinet
Periodically wipe the cabinet with a soft cloth and a diluted soap solution,
then with a dry cloth.
Caution:
O Do not use chemicals for cleaning (gasoline, paint thinner, etc.). It may
damage the cabinet.
O Do not apply oil to the inside of the unit. It may cause malfunctions.
O
O
O
Specifications
O
As part of our policy of continuous improvement, SHARP reserves the right
to make design and specification changes for product improvement without
prior notice. The performance specification figures indicated are nominal
values of production units. There may be some deviations from these values
in individual units.
File system support
O
O
Support USB devices with Microsoft
Windows/DOS/FAT 12/FAT 16/ FAT
32.
2 kbyte block length for sector.
Q General
Q Tuner
Power source
AC 120 V ~ 60 Hz
Power consumption
42 W
Frequency range
Dimensions
Width: 6 - 1/2" (165 mm)
Height: 8 - 2/3" (220 mm)
Depth: 9 - 1/4" (235 mm)
FM: 87.5 - 108 MHz
AM: 530 - 1,710 kHz
Preset
40 (FM and AM station)
8.6 lbs. (3.9 kg)
Q Speaker
Weight
Q CD player
Type
2-way type speaker system
2" (5 cm) tweeter
4" (10 cm) woofer
Type
Single disc multi-play compact disc player
Signal readout
Non-contact, 3-beam
semiconductor laser pickup
Maximum input power
100 W
Rated input power
50 W
D/A converter
Multi bit D/A converter
Impedance
4 ohms
Frequency response
20 - 20,000 Hz
Dimensions
Dynamic range
90 dB (1 kHz)
Width: 5 - 13/16" (148 mm)
Height: 8-11/16" (220 mm)
Depth: 6-7/16" (163 mm)
Weight
3.6 lbs (1.6 kg)/each
E-15
XL-DH229P_USA_EN.indd 15
12/28/2010 3:23:55 PM
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising