advertisement
▼
Scroll to page 2
of 72
4-130-031-11(3) Home Theatre System Operating Instructions HT-SF360 HT-SS360 ©2009 Sony Corporation For customers in Australia WARNING To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. To reduce the risk of fire, do not cover the ventilation opening of the apparatus with newspapers, tablecloths, curtain, etc. Do not place the naked flame sources such as lighted candles on the apparatus. To reduce the risk of fire or electric shock, do not expose this apparatus to dripping or splashing, and do not place objects filled with liquids, such as vases, on the apparatus. Do not install the appliance in a confined space, such as a bookcase or built-in cabinet. As the main plug is used to disconnect the unit from the mains, connect the unit to an easily accessible AC outlet. Should you notice an abnormality in the unit, disconnect the main plug from the AC outlet immediately. Do not expose batteries or apparatus with batteryinstalled to excessive heat such as sunshine, fire or the like. The unit is not disconnected from the mains as long as it is connected to the AC outlet, even if the unit itself has been turned off. To prevent injury, this apparatus must be securely attached to the floor/wall in accordance with the installation instructions. For models of area code SP, TH only This symbol is intended to alert the user to the presence of the Hot Surface that may be hot if it is touched during the normal operation. 2GB Disposal of Old Electrical & Electronic Equipment (Applicable in the European Union and other European countries with separate collection systems) For customers in Europe Disposal of Old Electrical & Electronic Equipment (Applicable in the European Union and other European countries with separate collection systems) This symbol on the product or on its packaging indicates that this product shall not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. The recycling of materials will help to conserve natural resources. For more detailed information about recycling of this product, please contact your local Civic Office, your household waste disposal service or the shop where you purchased the product. Disposal of waste batteries (applicable in the European Union and other European countries with separate collection systems) This symbol on the battery or on the packaging indicates that the battery provided with this product shall not be treated as household waste. On certain batteries this symbol might be used in combination with a chemical symbol. The chemical symbols for mercury (Hg) or lead (Pb) are added if the battery contains more than 0.0005% mercury or 0.004% lead. By ensuring these batteries are disposed of correctly, you will help prevent potentially negative consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of the battery. The recycling of the materials will help to conserve natural resources. In case of products that for safety, performance or data integrity reasons require a permanent connection with an incorporated battery, this battery should be replaced by qualified service staff only. To ensure that the battery will be treated properly, hand over the product at end-of-life to the applicable collection point for the recycling of electrical and electronic equipment. For all other batteries, please view the section on how to remove the battery from the product safely. Hand the battery over to the applicable collection point for the recycling of waste batteries. For more detailed information about recycling of this product or battery, please contact your local Civic Office, your household waste disposal service or the shop where you purchased the product. Notice for customers: The following information is only applicable to equipment sold in the countries applying EU Directives. The manufacturer of this product is Sony Corporation, 1-7-1 Konan Minato-ku Tokyo, 108-0075 Japan. The Authorized Representative for EMC and product safety is Sony Deutschland GmbH, Hedelfinger Strasse 61, 70327 Stuttgart, Germany. For any service or guarantee matters please refer to the addresses given in separate service or guarantee documents. 3GB On Copyrights About This Manual • The instructions in this manual are for model HT-SF360 and HT-SS360. • In this manual, models of area code CEL is used for illustration purposes unless stated otherwise. Any difference in operation is clearly indicated in the text, for example, “Models of area code AU only”. The HT-SF360 consists of: • Receiver • Speaker systema) – Front speaker – Center speaker – Surround speaker – Subwoofer STR-KS360S SS-MSP36F SS-CNP36 SS-SRP36F SS-WP36 The HT-SS360 consists of: • Receiver • Speaker systema) – Front speaker – Center speaker – Surround speaker – Subwoofer a) STR-KS360S SS-MSP36S SS-CNP36 SS-SRP36S SS-WP36 About area codes The area code of the receiver you purchased is shown on the lower portion of the rear panel (see the illustration below). SPEAKERS FRONT L SUR R SUR L CENTER SUBWOOFER Area code Any differences in operation, according to the area code, are clearly indicated in the text, for example, “Models of area code AA only”. 4GB This receiver incorporates High-Definition Multimedia Interface (HDMI TM) technology. HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC. “x.v.Colour” and “x.v.Colour” logo are trademarks of Sony Corporation. “BRAVIA” is a trademarks of Sony Corporation. Be sure to use only the supplied speakers. • The instructions in this manual describe the controls on the supplied remote. You can also use the controls on the receiver if they have the same or similar names as those on the remote. FRONT R This receiver incorporates Dolby* Digital and Pro Logic Surround and the DTS** Digital Surround System. * Manufactured under license from Dolby Laboratories. Dolby, Pro Logic, and the doubleD symbol are trademarks of Dolby Laboratories. ** Manufactured under license under U.S. Patent #’s: 5,451,942; 5,956,674; 5,974,380; 5,978,762; 6,487,535 & other U.S. and worldwide patents issued & pending. DTS and DTS Digital Surround are registered trademarks and the DTS logos and Symbol are trademarks of DTS, Inc. © 1996-2008 DTS, Inc. All Rights Reserved. “S-AIR” and its logo are trademarks of Sony Corporation. Table of Contents Description and location of parts .................. 6 Tuner Operations Getting Started 1: Installing the speakers............................. 13 2: Connecting the speakers ......................... 15 3: Connecting the TV .................................. 16 4: Connecting the audio/video components 17 5: Connecting the antennas ......................... 21 6: Preparing the receiver and the remote..... 22 7: Calibrating the appropriate settings automatically (AUTO CALIBRATION) ...................... 23 8: Adjusting the speaker levels (TEST TONE)........................................ 27 Playback Selecting a component ................................ 28 Enjoying sound/images from the components connected to the receiver ... 29 Amplifier Operations Navigating through menus .......................... 31 Settings for the HDMI (SET HDMI menu) ................................ 35 Settings for the Auto Calibration (A.CAL menu) ....................................... 35 Settings for the Speaker (SP SETUP menu) ................................. 36 Adjusting the level (LEVEL menu) ............ 37 Adjusting the tone (TONE menu) ............... 37 Settings for the Custom Menu (CUSTOM menu) .................................. 38 Settings for the S-AIR (S-AIR menu)......... 39 Listening to FM/AM radio ..........................41 Presetting radio stations...............................42 Using the Radio Data System (RDS) ..........44 (Models of area code CEL, CEK only) Using “BRAVIA” Sync features What is “BRAVIA” Sync?...........................45 Preparing for the “BRAVIA” Sync..............45 Playing back components with one-touch operation (One-Touch Play) ...................47 Enjoying the TV sound from the speakers connected to the receiver (System Audio Control) .........................47 Turning off the receiver with the TV (System Power Off)................................48 Using the Power Saving function (Power Save)...........................................49 Other Operations Changing the brightness of the display (DIMMER).............................................50 Changing the display setting (DISPLAY).............................................50 Using the Sleep Timer (SLEEP)..................51 Switching the audio input mode (IN MODE) ............................................51 Using an S-AIR Product..............................52 Using the Remote Changing the input button assignments.......60 Enjoying Surround Sound Additional Information Selecting the sound field ............................. 40 Glossary.......................................................61 Precautions ..................................................63 Troubleshooting...........................................64 Specifications ..............................................69 Index.............................................. Back cover 5GB Description and location of parts Front panel 1 2 3 4 5 6 7 INPUT SELECTOR ?/1 MASTER VOLUME ACTIVE STANDBY Name Function A ?/1 (on/standby) Press to turn the receiver on or off (page 22, 29, 30). B ACTIVE STANDBY lamp Lights up in amber when the Control for HDMI and/or S-AIR standby mode are set to on and the receiver is on standby mode. Note If the ACTIVE STANDBY lamp is flashing, see page 68. C Display The current status of the selected component or a list of selectable items appears here (page 7). D White lamp Lights up when the receiver is on and DSPL is set to on in DISPLAY function (page 50). Lights off when the receiver is in standby mode or DSPL is set to off in DISPLAY function. E Remote sensor Receives signals from remote commander. F MASTER VOLUME Turn to adjust the volume level of all speakers at the same time (page 28, 29, 30). G INPUT SELECTOR Press to select the input source to playback (page 28, 29, 30, 42). 6GB Indicators on the display 12 3 qd 4 qs 5 6 7 8 qa q; 9 Name Function Name Function A LFE Lights up when the disc being played back contains an LFE (Low Frequency Effect) channel and the LFE channel signal is actually being reproduced. F HDMI Lights up when a playback component is connected to this receiver using an HDMI jack (page 19). B SLEEP Lights up when the sleep timer is activated (page 51). G Preset station indicators C Playback channel indicators The letters (L, C, R, etc.) indicate the channels being played back. The boxes around the letters vary to show how the receiver downmixes the source sound. Front Left Front Right Center (monaural) Surround Left Surround Right Surround (monaural or the surround components obtained by Pro Logic processing) Example: Recording format (Front/ Surround): 3/2.1 Sound Field: A.F.D. AUTO Lights up when using the receiver to tune in radio stations you have preset. For details on presetting radio stations, see page 42. H Tuner indicators Lights up when using the receiver to tune in radio stations (page 41), etc. I COAX Lights up when the source signal is a digital signal being input through the COAX IN jack. J OPT Lights up when the source signal is a digital signal being input through the OPT IN jack. K “ PL” lights up when the receiver applies Pro Logic processing to 2 channel signals in order to output the center and surround channel signals. “ PLII” lights up when the Pro Logic II Movie/Music decoder is activated. L R C SL SR S L SW D D E S-AIR SL C PL/ PLII R SR Lights up when receiver is decoding Dolby Digital signals. Note When playing a Dolby Digital format disc, be sure that you have made digital connections. Lights up when the S-AIR transmitter (not supplied) is connected. L DTS Lights up when the receiver is decoding DTS signals. Note When playing a DTS format disc, be sure that you have made digital connections. M SW Lights up when the audio signal is output from the SUBWOOFER jack. 7GB Rear panel 1 2 34 5 L L R R 6 7 TV DIGITAL ANTENNA EZW-T100 AM AUTO AUDIO IN AUDIO IN AUDIO IN SA-CD/CD CAL MIC VIDEO 1 TV SPEAKERS DC5V COAX IN OPT IN VIDEO 2 SAT OPT IN 700mA MAX HDMI FRONT R FRONT L SUR R SUR L CENTER SUBWOOFER A SPEAKERS section BD IN B S-AIR (EZW-T100) CAUTION Please do not remove the slot cover until you want to install the wireless transmitter. HDMI IN/ OUT jacks C DMPORT DMPORT jack Connects to a DIGITAL MEDIA PORT adapter (page 18). D AUTO CALIBRATION section AUTO CAL Connects to the MIC jack supplied optimizer microphone for the Auto Calibration function (page 24). E AUDIO INPUT section White (L) Red (R) 8GB AUDIO IN jacks SAT IN OUT OPT IN jacks Connects to a DVD player, etc. The COAX IN jack COAX IN provides a better jack sound quality (page 20). Connects to a wireless transmitter (not supplied) (page 52). slot DVD IN F DIGITAL INPUT/OUTPUT section Connects to the supplied speakers and subwoofer (page 15). With slot cover DMPORT Connects to a Super Audio CD player, CD player, etc. (page 18, 20). Connects to a DVD player, satellite tuner, or a Blu-ray disc player. The image is output to a TV or a projector while the sound can be output from a TV or/and speakers connected to this receiver (page 19). G ANTENNA section FM ANTENNA jack Connects to the supplied FM wire antenna (page 21). AM ANTENNA terminals Connects to the supplied AM loop antenna (page 21). Basic operations Remote commander Remote Button Function You can use the supplied remote RM-AAU058 to operate the receiver and to control the Sony audio/video components that the remote is assigned to operate (page 60). B ?/1 (on/standby) RM-AAU058 Saving the power in standby mode 1 TV ?/1 DMPORT AV ?/1 ?/1 – When “CONTROL FOR HDMI” is set to “CTRL ON” and “P.SAVE” is set to “SAVE ON” (page 35). – When S-AIR standby “STBY” is set to “STBY OFF” (page 59). 2 ws SYSTEM STANDBY wa VIDEO1 VIDEO2 SAT TV BD DVD SA-CD/CD TUNER BD/DVD TOP MENU MENU F1 F2 AUDIO THEATRE DIGITAL ANALOG w; ql 1 2 3 4 5 6 7 8 9 0 DISPLAY 4 ENTER TOOLS/ OPTIONS qk qj 7 8 9 q; qa qs qh RETURN/EXIT TV CH – PRESET – < . MENU/HOME TV CH + PRESET + < > TUNING + TUNING – m C Input buttons 6 SOUND FIELD AMP MENU CLEAR 3 5 H M X x Press one of the buttons to select the component you want to use. The buttons are factory assigned to control Sony components. You can change the button assignments following the steps in “Changing the input button assignments” on page 60. G SOUND FIELD Press to select a sound field. I AMP MENU Press to display the menu of the receiver. K Press to turn off the sound temporarily. Press again to restore the sound. qd (Muting) qf TV qg Press to turn the receiver on or off. To turn off all Sony components, press ?/1 and AV ?/1 (A) at the same time (SYSTEM STANDBY). L Q +*/– , V/v/B/b Press to adjust the volume. Press V, v, B or b to select the settings. Then, press to enter the selection. continued 9GB Tuner operations Common operations Remote Button Function Remote Button Function H ENTER Press to enter the selection. M MENU/HOME Press to display the menu. A TV ?/1 AV ?/1 (on/standby) N PRESET +/– Press to select a preset station. Press to turn on or off the Sony audio/video components that the remote is assigned to operate (page 60). Press A ?/1 and B TV ?/1/AV ?/1 at the same time to turn off the receiver and all other components that the remote is assigned to operate (SYSTEM STANDBY). H ENTER Press to enter the selection. T Numeric buttons (number 5*) Press to select channels and tracks directly. Q TUNING +/– Press to scan the station. , V/v/B/b Press to select the menu items and to enter the selection. R DISPLAY Press to display information during TUNER function. S CLEAR Press to clear a mistake when you input a wrong character. DMPORT operations Remote Button Function N ./> m/M Press to skip the track. Press to fast reverse or fast forward. H* (playback)/ Play mode button. X (pause, press again to resume normal playback/ x (stop) To control the component 1 To control the TV Press and hold (O) TV (yellow) button while pressing the buttons with a yellow dot or yellow printing to control the TV. Remote Button Function D AUDIO To change the screen format (Screen mode) manually to suit the broadcast. E THEATRE Press to sets the optimal picture settings automatically for watching movies, when you connect a Sony TV which is compatible with the THEATRE button. Also, the audio is automatically switched to the audio output of this receiver when you connect the TV and the receiver with HDMI connection, and the Control for HDMI function is set to on. F Press to display the guide when you are watching analog and digital channels. Press one of the input buttons C (TV, BD, DVD or SAT) to select the component you want to operate. The component assigned to the selected input button becomes operable. 2 Referring to the following table, press the corresponding button for the operation. (Guide) H (Previous channel) 10GB Select the desired audio signal. Press to return to the previous channel watched (for more than five seconds). Remote Button Function Remote Button Function J TOOLS/ OPTIONS Press to enable you to access various viewing options and change/make adjustments according to the source and screen format. V K Press to turn off the sound. (Muting) L +*/– M MENU/HOME N TV CH +/– c/C P RETURN/ EXIT Q , V/v/B/b R DISPLAY / (Info/Text reveal) S / (Text) Press to adjust the volume. Press to allow you to select channels or input sources and change the settings for your TV. In TV mode: Press to select the next (+) or previous (–) channel. In Text mode: Press to select the next (c) or previous (C) page. Remote Button Function D F1 F2 Press to select the HDD. Press to select the Blu-ray Disc/DVD. M MENU/HOME Press to display the menu. N . Press to skip chapters. < Press to select the menu item and enters the selection. Press to display the TV’s information on the TV screen. (Displays the current channel number, etc.) Press to jump backward while viewing live or recorded programs. < Press to jump forward while viewing recorded programs. > Press to skip forward to the next available chapter. m/M Press to fast reverse or to fast forward the disc when pressed during playback. H* (playback)/ Play mode button. X (pause, press again to resume normal playback/ x (stop) Q , V/v/B/b U BD/DVD TOP MENU, MENU Press to select a menu item and enters the selection. Press to display the top menu or disc menu. Press to display Text. T Numeric buttons (number 5*) Press to select channels. Press ENTER (H) to change channels immediately. U ANALOG Press to change to analog mode. DIGITAL In TV mode: Press to select input. In Analogue Text mode: Press to hold the current page. To control the DVD recorder/Blu-ray Disc recorder Return to the previous screen of any displayed menu. In digital mode: Press to display brief details of the program currently being watched. In analogue mode: Press to display information such as current channel number and screen format. In Text mode: Press to reveal hidden information (e.g. answers to a quiz). / (Input select/ Text hold) Press to change to digital mode. continued 11GB To control the DVD player/Blu-ray Disc player To control the SAT Remote Button Function F Remote Button Function Press to display the guide menu. M MENU/HOME Press to display the menu. N ./> Press to skip chapters. M MENU/HOME Press to display the menu. Press to jump backward. Q Press to select a menu item and enters the selection. < < m/M Press to jump forward. Press to fast reverse or to fast forward the disc when pressed during playback. H* (playback)/ Play mode button. X (pause, press again to resume normal playback/ x (stop) Q , V/v/B/b U BD/DVD TOP MENU, MENU Press to select a menu item and enters the selection. Press to display the top menu or disc menu. To control the HDD/DVD COMBO Remote Button Function D F1 Press to select the HDD. F2 Press to select the DVD. M MENU/HOME Press to display the menu. N ./> Press to specify the previous/next chapter/track. < < m/M Press to change to replay mode. Press to advance. Press to fast reverse or to fast forward the disc when pressed during playback. H* (playback)/ Play mode button. X (pause, press again to resume normal playback/ x (stop) Q , V/v/B/b U BD/DVD TOP MENU, MENU 12GB Press to move the highlight (cursor) and selects the item. Press to display the top menu or disc menu. (Guide) , V/v/B/b * The number 5, 2 + and H buttons have tactile dots. Use the tactile dots as references when operating the receiver. Notes • Some functions explained in this section may not work depending on the model. • The above explanation is intended to serve as an example only. Therefore, depending on the component, the above operation may not be possible or may operate differently than described. HT-SS360 only Getting Started Getting Started 1: Installing the speakers This receiver allows you to use a 5.1 channel speaker system. To fully enjoy theater-like multi channel surround sound, be sure to connect all the speakers (two front speakers, a center speaker, and two surround speakers) and a subwoofer (5.1 channel). You can place your speakers as shown below. AFront speaker (left) BFront speaker (right) CCenter speaker DSurround speaker (left) ESurround speaker (right) FSubwoofer HT-SF360 only Tip Since the subwoofer does not emit highly directional signals, you can place it wherever you want. 13GB Installing the speakers on a flat surface Installing the speakers on the wall Before you install the speaker and subwoofer, be sure to attach the supplied foot pads to prevent vibration or movement as shown in the illustration below. You can install your speakers on the wall. 1 Example of HT-SS360 front speaker Prepare screws (not supplied) that are suitable for the hook on the back of each speaker. See the illustrations below. 4 mm more than 25 mm 4.6 mm 10 mm Hook on the back of the speaker Attach the supplied foot pad to the below speakers Model Speakers HT-SF360 center speaker and subwoofer HT-SS360 all the speakers and subwoofer Installing the speakers on the speaker stand 2 Fasten the screws to the wall. The screws should protrude 5 to 7 mm. For the center speaker 160 mm 5 mm to 7 mm For greater flexibility in positioning the speakers, you are recommended to use the speaker stand below. Model Speaker Stand HT-SF360 Supplied. For details, refer to the supplied speaker stand installation guide. HT-SS360 Optional WS-FV11 or WS-FV10D speaker stand (available only in certain countries). For details, refer to the operating instructions supplied with the speaker stand. 14GB For the front speakers of HT-SF360 5 mm to 7 mm 217 mm For the surround speakers of HT-SF360 Before connecting the cords, be sure to disconnect the AC power cord (mains lead). C B F For the front and surround speakers of HT-SS360 A 5 mm to 7 mm 3 Hang the speakers on the screws. SPEAKERS 4.6 mm FRONT R FRONT L SUR R SUR L CENTER SUBWOOFER 10 mm Connector A A Rear of speaker A D E Notes • Use screws that are suitable for the wall material and strength. As a plaster board wall is especially fragile, attach the screws securely to a beam and fasten them to the wall. Install the speakers on a vertical and flat wall where reinforcement is applied. • Contact a screw shop or installer regarding the wall material or screws to be used. • Sony is not responsible for accident or damage caused by improper installation, insufficient wall strength or improper screw installation, natural calamity, etc. • For HT-SF360, if you install the speakers on the wall, you do not need to attach the supplied speaker stand. A Speaker cord (supplied) AFront speaker (left) BFront speaker (right) CCenter speaker DSurround speaker (left) ESurround speaker (right) FSubwoofer continued 15GB Getting Started 100 mm 5 mm to 7 mm 2: Connecting the speakers Note on speaker cords The connector of the speaker cords are the same color as the speaker jack to be connected. When connecting a speaker cord, be sure to match the colored connector to the speaker jack on the receiver: Connector Speaker jack Red FRONT R White FRONT L Grey SUR R Blue SUR L Green CENTER Purple SUBWOOFER 3: Connecting the TV You can watch the selected input image when you connect the HDMI OUT jack to a TV. It is not necessary to connect all the cords. Connect audio and video cords according to the jacks of your components. Before connecting the cords, be sure to disconnect the AC power cord. TV Audio signal Audio/video signal To connect the speakers correctly Check the speaker type by referring to the speaker label* at the rear panel of the speakers. Character on speaker label Speaker type L Front left R Front right SL Surround left SR Surround right * The center speaker and subwoofer do not have the character on the speaker label. For details on the speaker type, see page 4. A L L R B TV DIGITAL C ANTENNA R AM AUDIO IN AUDIO IN AUDIO IN COAX IN OPT IN VIDEO 1 TV SA-CD/CD VIDEO 2 SAT OPT IN mA MAX HDMI BD IN RT DVD IN SAT IN OUT A Audio cord (not supplied) B Optical digital cord (not supplied) C HDMI cable (not supplied) We recommend that you use a Sony HDMI cable. Notes • Be sure to turn on the receiver when the video and audio signals of a playback component are being output to a TV via the receiver. Unless the power is turned on, neither video nor audio signals will be transmitted. • When connecting optical digital cords, insert the plugs straight in until they click into place. • Do not bend or tie optical digital cords. 16GB Tips 4: Connecting the audio/ video components How to hook up your components This section describes how to hook up your components to this receiver. Before you begin, refer to “Component to be connected” below for the pages which describe how to connect the audio/video components. Before connecting the cords, be sure to disconnect the AC power cord (mains lead). After hooking up all your components, proceed to “5: Connecting the antennas” (page 21). Component to be connected To connect See TV page 16 Audio components • Super Audio CD player/ CD player • DIGITAL MEDIA PORT adapter page 18 Components with HDMI jack page 19 Video components • Satellite tuner, Set-top box • DVD player, DVD recorder • VCR page 20 17GB Getting Started • To output the sound of the TV from the speakers connected to the receiver, be sure to – connect the audio output jacks of the TV to the TV IN jacks of the receiver. – turn off the TV’s volume or activate the TV’s muting function. • All the digital audio jacks are compatible with 32 kHz, 44.1 kHz, 48 kHz, and 96 kHz sampling frequencies. Connecting audio components The following illustration shows how to connect audio components such as Super Audio CD player, CD player and DIGITAL MEDIA PORT adapter. You can also view the images on the TV screen by connecting the video output of the DIGITAL MEDIA PORT adapter to the video input of the TV. Super Audio CD player, CD player Audio signal A Notes on connecting DIGITAL MEDIA PORT adapter • Do not connect or disconnect the DIGITAL MEDIA PORT adapter while the receiver is turned on. • Be sure to make DMPORT connections firmly, insert the connector straight in. • As the connector of the DIGITAL MEDIA PORT adapter is fragile, be sure to handle with care when placing or moving the receiver. • When connecting the DIGITAL MEDIA PORT adapter, be sure the connector is inserted with the arrow mark facing toward the arrow mark on the DMPORT jack. To detach the DIGITAL MEDIA PORT adapter, press and holed both sided of the connector and then pull out the connector. 1 2 L L R R TV DIGITAL EZW-T100 AUTO AUDIO IN AUDIO IN AUDIO IN SA-CD/CD CAL MIC VIDEO 1 TV DC5V COAX IN OPT IN VIDEO 2 SAT OPT IN 700mA MAX HDMI DMPORT BD IN DVD IN SAT IN TV DIGITAL MEDIA PORT adapter B A Audio cord (not supplied) B Video cord (not supplied) * The type of connector varies depending on the DIGITAL MEDIA PORT adapter. For details, refer to the operating instructions supplied with the DIGITAL MEDIA PORT adapter. 18GB DC5V 700mA DM PO RT MAX 1 Connecting components with HDMI jacks TV, etc. By connecting Sony “BRAVIA” Sync compatible components using HDMI cables, ““BRAVIA” Sync Features” makes operations simpler (page 45). C L L R B A TV DIGITAL ANTENNA R AM AUDIO IN AUDIO IN AUDIO IN COAX IN OPT IN VIDEO 1 TV SA-CD/CD VIDEO 2 SAT OPT IN mA MAX HDMI BD IN RT A DVD IN SAT IN OUT A A Audio/video signals Audio/video signals Audio/video signals Blu-ray disc player DVD recorder, DVD player a) Satellite tuner/ Set-top box HDMI features • A digital audio signals transmitted by HDMI can be output from the speakers connected to the receiver. This signal supports Dolby Digital, DTS and Linear PCM. • This receiver supports xvYCC transmission. • This receiver supports the Control for HDMI function. For details, see “Using “BRAVIA” Sync features” (page 45). A HDMI cable (not supplied) We recommend that you use a Sony HDMI cable. B Optical digital cord (not supplied)b) C Audio cord (not supplied)b) a) If you connect a DVD player, be sure to change the factory setting of the DVD button on the remote so that you can use the button to control your DVD player. For details, see “Changing the input button assignments” (page 60). b) Connect at least one of the audio cords (B or C). continued 19GB Getting Started HDMI is the abbreviated name for HighDefinition Multimedia Interface. It is an interface which transmits video and audio signals in digital format. Sony recommends that you connect components to the receiver using an HDMI cable. With HDMI, you can easily enjoy both high quality sound and high quality images. However, it is necessary to connect the audio output of the TV to the audio input of the receiver using an optical cord to listen to the TV multi channel surround sound broadcasting from the receiver. Audio/video signals Audio signals Notes on HDMI connections • An audio signal input to the HDMI IN jack is output from the SPEAKERS jacks and HDMI OUT jack. It is not output from any other audio jacks. • Video signals input to the HDMI IN jack can only be output from the HDMI OUT jack. • The multi/stereo area audio signals of a Super Audio CD are not output. • Audio signals (sampling frequency, bit length, etc.) transmitted from an HDMI jack may be suppressed by the connected component. Check the setup of the connected component if the image is poor or the sound does not come out of a component connected via the HDMI cable. • Sound may be interrupted when the sampling frequency, the number of channels or the audio format of the audio output signals from the playback component is switched. • When the connected component is not compatible with copyright protection technology (HDCP), the image and/or the sound from the HDMI OUT jack may be distorted or may not be output. In this case, check the specification of the connected component. • You can enjoy multi channel Linear PCM only with an HDMI connection. • Set the image resolution of the playback component to 720p, 1080i or 1080p when you output 96 kHz multi channel sound over an HDMI connection. • You may need to make certain settings on the image resolution of the player before you can enjoy multi channel Linear PCM. Refer to the operating instructions of the player. • Refer to the operating instructions of each component connected for details. • We do not recommend using an HDMI-DVI conversion cable. When you connect an HDMI-DVI conversion cable to a DVI-D component, the sound and/or the image may not be output. 20GB Connecting video components The following illustration shows how to connect video components such as DVD player, DVD recorder, VCR, etc. It is not necessary to connect all the cords. Connect audio and video cords according to the jacks of your components. DVD recorder, DVD player Satellite tuner, Set-top box Audio signal Audio signal B L L R R TV DIGITAL ANTENNA AM AUTO AUDIO IN AUDIO IN AUDIO IN SA-CD/CD CAL MIC VIDEO 1 TV DC5V C COAX IN OPT IN VIDEO 2 SAT OPT IN 700mA MAX HDMI BD IN DMPORT DVD IN SAT IN OUT A Audio signal VCR A Audio cord (not supplied) B Coaxial digital cord (not supplied) C Optical digital cord (not supplied) Notes 5: Connecting the antennas Connect the supplied AM loop antenna and FM wire antenna. Before connecting the antennas, be sure to disconnect the AC power cord (mains lead). FM wire antenna (supplied) AM loop antenna (supplied) Tip All the digital audio jacks are compatible with 32 kHz, 44.1 kHz, 48 kHz, and 96 kHz sampling frequencies. L L R TV DIGITAL ANTENNA R AM AUDIO IN AUDIO IN AUDIO IN COAX IN OPT IN VIDEO 1 TV SA-CD/CD VIDEO 2 SAT OPT IN mA MAX HDMI RT BD IN DVD IN SAT IN OUT * The shape of the connector varies depending on the area code of this receiver. Notes • To prevent noise pickup, keep the AM loop antenna away from the receiver and other components. • Be sure to fully extend the FM wire antenna. • After connecting the FM wire antenna, keep it as horizontal as possible. 21GB Getting Started • To input multi channel digital audio from the DVD player, set the digital audio output setting on the DVD player. Refer to the operating instructions supplied with the DVD player. • When connecting optical digital cords, insert the plugs straight in until they click into place. • Do not bend or tie optical digital cords. • Be sure to connect the video output of the DVD player, DVD recorder and VCR to the TV, so that the image is displayed on the TV. Refer to the operating instructions of each connected component for details. • You cannot do recording on the DVD recorder or VCR via this receiver. For details, refer to the operating instructions supplied with the DVD recorder or VCR. 6: Preparing the receiver and the remote Connecting the AC power cord (mains lead) Inserting batteries into the remote Insert two R6 (size-AA) batteries in the RM-AAU058 Remote Commander. Observe the correct polarity when installing batteries. Connect the AC power cord (mains lead) to a wall outlet. AC power cord (mains lead) SPEAKERS Notes FRONT R FRONT L SUR R SUR L CENTER To the wall outlet Performing initial setup operations Before using the receiver for the first time, initialize the receiver by performing the following procedure. This procedure can also be used to return settings you have made to their factory defaults. Be sure to use the buttons on the receiver for this operation. 1,2 INPUT SELECTOR ?/1 MASTER VOLUME ACTIVE STANDBY 1 Press ?/1 to turn on the receiver. 2 Hold down ?/1 for 5 seconds. “CLEARED” appears. All the settings you have changed or adjusted are reset to the initial settings. 22GB • Do not leave the remote in an extremely hot or humid place. • Do not use a new battery with old ones. • Do not mix manganese batteries and other kinds of batteries. • Do not expose the remote sensor to direct sunlight or lighting apparatuses. Doing so may cause a malfunction. • If you do not intend to use the remote for an extended period of time, remove the batteries to avoid possible damage from battery leakage and corrosion. • When you replace the batteries, the remote buttons may be reset to their factory settings. If this happens, reassign the buttons again (page 60). • When the remote no longer operates the receiver, replace all the batteries with new ones. (AUTO CALIBRATION) This receiver is equipped with DCAC (Digital Cinema Auto Calibration) Technology which allows you to perform automatic calibration as follows: • Check the connection between each speaker and the receiver. • Adjust the speaker level. • Measure the distance of each speaker from your listening position. • Measure the frequency characteristics.* * The measurement result is not utilized for signals with a sampling frequency of more than 96 kHz. The DCAC is designed to obtain proper sound balance in your room. However, you can adjust the speaker levels manually according to your preference. For details, see “8: Adjusting the speaker levels (TEST TONE)” (page 27). Before you perform Auto Calibration Before you perform the Auto Calibration, set up and connect the speakers (page 13, 15). • The AUTO CAL MIC jack is used for the supplied optimizer microphone only. Do not connect other microphones to this jack. Doing so may damage the receiver and the microphone. • During the calibration, the sound that comes out of the speakers is very loud. The volume of the sound cannot be adjusted. Pay attention to the presence of children or to the effect on your neighborhood. • Perform the Auto Calibration in a quiet environment to avoid the effect of noise and to get a more accurate measurement. • If there are any obstacles in the path between the optimizer microphone and the speakers, the calibration cannot be performed correctly. Remove any obstacles from the measurement area to avoid measurement error. Notes • If the muting function has been activated before you perform Auto Calibration, the muting function will be set to off automatically. • When you use the S-AIR product, disconnect the headphones. continued 23GB Getting Started 7: Calibrating the appropriate settings automatically Example: HT-SS360 L L R R Performing Auto Calibration TV DIGITAL ANTENNA EZW-T100 AM AUTO AUDIO IN AUDIO IN AUDIO IN SA-CD/CD CAL MIC VIDEO 1 TV SPEAKERS DC5V COAX IN OPT IN VIDEO 2 SAT OPT IN 700mA MAX HDMI FRONT R FRONT L SUR R SUR L CENTER SUBWOOFER DMPORT BD IN DVD IN SAT IN Optimizer microphone OUT TV ?/1 DMPORT AV ?/1 ?/1 ?/1 switch SYSTEM STANDBY VIDEO1 VIDEO2 SAT TV BD DVD SA-CD/CD TUNER BD/DVD TOP MENU MENU F1 F2 AUDIO THEATRE DIGITAL ANALOG 1 2 3 4 5 6 7 8 9 CLEAR 0 SOUND FIELD AMP MENU ENTER 2 +/– ,V,v,B,b RETURN/EXIT 2 Connect the supplied optimizer microphone to the AUTO CAL MIC jack. Set up the optimizer microphone. Place the optimizer microphone at your listening position.You can also use a stool or tripod so that the optimizer microphone remains at the same height as your ears. Tip When you face the speaker towards the optimizer microphone, you will get a more accurate measurement. 24GB AMP MENU TOOLS/ OPTIONS DISPLAY 1 Input buttons MENU/HOME 1 2 Press AMP MENU. 3 Press menu. Press V/v repeatedly to select “A.CAL”. or b to enter the “START” appears on the display. 4 Press to start the measurement. Measurement starts in 5 seconds. While the time is counting down, stand away from the measurement area to avoid measurement error. The measurement process will take approximately 30 seconds to complete. The table below shows the display when measurement starts. Measurement for Display Speaker existance TONE Speaker gain, distance, frequency response T.S.P. Subwoofer gain and distance WOOFER 2 Notes Press V/v repeatedly to select the item. Then, press . Item Explanation SAVE Saves the measurement results and exits the setting process. WRN CHK Displays warning concerning the measurement results. See “When you select “WRN CHK”” (page 26). DIST Displays the measurement result for speaker distance. LEVEL Displays the measurement result for speaker level. EXIT Exits the setting process without saving the measurement results. Tips • When Auto Calibration starts: – Stand some distance from the speakers and the listening position to avoid measurement failure. This is because test signals are output from the speakers during measurement. – Avoid making noise to get a more accurate measurement. • The Auto Calibration function will be canceled when you do the following during the measurement process: – Press ?/1 or . – Press input buttons on the remote or INPUT SELECTOR on the receiver. – Change the volume level. Confirming/saving the measurement results 1 After “SAVE” is displayed for 50 seconds, the measurement result is saved automatically, without the need to save the procedure. 3 Confirm the measurement result. When the measurement ends, a beep sounds and the measurement result appears on the display. Measurement Display result Note Explanation When the measurement process completes properly SAVE Proceed to step 2. When the measurement process fails ERROR XXXX See “When error codes appear” (page 25). Save the measurement result. Select “SAVE” in step 2. The measurement results are saved. When error codes appear Try the remedies and perform the Auto Calibration again. Error code Cause and remedies ERROR 32 • The sound input from the optimizer microphone is out of the acceptable range. • The optimizer microphone or subwoofer may be damaged. Contact your Sony dealer or local authorized Sony service facility. ERROR F 33 The front speakers are not connected. Check that the front speakers are connected properly. ERROR SR 33 Either the surround left or surround right speaker is not connected. Check that the surround speakers are connected properly. continued 25GB Getting Started • If “PHONES” appears, you cannot perform the Auto Calibration. Disconnect the headphones from the S-AIR product you are using, then restart the Auto Calibration. • If “CHK MIC” appears, you cannot perform the Auto Calibration. Connect the calibration mic, then restart the Auto Calibration. Error code Cause and remedies ERROR SW 33 The subwoofer may be damaged. Contact your Sony dealer or local authorized Sony service facility. When you select “WRN CHK” If a warning on the measurement result is present, detailed information is displayed. Press or B to return to step 2 of “Confirming/saving the measurement results”. Warning code Explanation WARN 40 The Auto Calibration has completed. However, the noise level is high. You may be able to perform the Auto Calibration properly if you try it again, even though the measurement cannot be performed in all environments. Try to perform the Auto Calibration in a quiet environment. WARN 41 WARN 42 The sound input from the optimizer microphone is out of the acceptable range. The distance between the optimizer microphone and the speakers is too closed. Set them away, and then try to perform the Auto Calibration. WARN 43 The distance and position of a subwoofer cannot be detected. This may be caused by noise. Try to perform the Auto Calibration in a quiet environment. NO WARN There is no warning information. When you select “DIST” or “LEVEL” You can check the speaker distance or speaker level. When you have finished Disconnect the optimizer microphone from the receiver. 26GB Note If you have changed the position of the speakers, it is recommended that you perform Auto Calibration again in order to enjoy the surround sound. Clearing the measurement result You can delete the result of Auto Calibration. If there is no saved data, you cannot delete the result. 1 2 Press AMP MENU. 3 Press V/v repeatedly to select “A.CAL CLR”, then press or b. 4 Press V/v repeatedly to select “YES”, then press . Press V/v repeatedly until “A.CAL” appears, then press or b. The saved result is deleted. The settings for speaker distance and speaker level return to their defaults. 8: Adjusting the speaker levels (TEST TONE) You can adjust the speaker levels while listening to the test tone from your listening position. AMP MENU CLEAR DISPLAY 0 ENTER AMP MENU TOOLS/ OPTIONS 7 , V,v,B,b 2 +/– RETURN/EXIT 1 Notes • “CNT LVL” does not appear when you set “CNT N” in the “SP SETUP” setting. • “SR LVL” and “SL LVL” do not appear when you set “SUR N” in the “SP SETUP” setting. MENU/HOME You can adjust from –6.0 dB to +6.0 dB in 0.5 dB steps. Press AMP MENU. Note “SET HDMI” appears on the display. 2 Press V/v repeatedly until “LEVEL” appears, then press or b. 3 Press V/v repeatedly until “T. TONE” appears, then press or b. 4 Press V/v repeatedly to select “T. TONE Y”, then press . The test tone is output from each speaker in sequence as follows: Front left t Center t Front right t Surround right t Surround left t Subwoofer 5 6 Press V/v repeatedly to adjust the speaker level, then press or b. If you do not adjust for a certain period, the test tone is emitted from the next speaker in sequence. 8 Repeat step 6 and 7 to adjust the other speaker level. 9 After you have finished making adjustments, press V/v until “T. TONE” appears, then press or b. 10 Press V/v repeatedly to select “T. TONE N”, then press . 11 Press AMP MENU. The AMP menu turns off. Press B until “T. TONE” appears. Press V/v repeatedly to select the desired speaker, then press or b. The test tone is emitted from the speaker that is being adjusted only. • FL LVL: adjusts the front left speaker level. • CNT LVL: adjusts the center speaker level. When a test tone is not output from the speakers • The speaker cords may not be connected securely. • The speaker cords may have the short-circuit problem. • The test tone signals are not output from the HDMI OUT jack. 27GB Getting Started • FR LVL: adjusts the front right speaker level. • SR LVL: adjusts the surround right speaker level. • SL LVL: adjusts the surround left speaker level. • SW LVL: adjusts the subwoofer level. Playback Selecting a component TV ?/1 DMPORT AV ?/1 ?/1 SYSTEM STANDBY VIDEO1 VIDEO2 SAT TV BD/DVD TOP MENU MENU BD DVD SA-CD/CD TUNER F1 Input buttons F2 AUDIO THEATRE DIGITAL ANALOG 1 2 4 5 6 7 8 9 CLEAR 0 ENTER Selected input [Display] Components that can be played back DMPORT [DMPORT] DIGITAL MEDIA PORT adapter connected to the DMPORT jack VIDEO1 or VIDEO2 [VIDEO 1 or VIDEO 2] VCR, etc., connected to the VIDEO 1 or VIDEO 2 jack BD [BD] Blu-ray disc player, etc., connected to the BD jack DVD [DVD] DVD player, DVD recorder, etc., connected to the DVD jack SAT [SAT] Satellite tuner, set-top box, etc., connected to the SAT jack TV [TV] TV, etc., connected to the TV jack SA-CD/CD [SA-CD/CD] Super Audio CD/CD player, etc., connected to the SA-CD/CD jack 3 SOUND FIELD AMP MENU DISPLAY TOOLS/ OPTIONS 2 +/– RETURN/EXIT 1 TUNER Built-in radio tuner [FM or AM band] MENU/HOME Press the input button to select a component. 2 Turn on the component and start playback. You can also use INPUT SELECTOR on the receiver. The selected input appears on the display. 3 Press 2 +/– to adjust the volume. You can also use MASTER VOLUME on the receiver. To activate the muting function Press . The muting function will be canceled when you do the following. • Press again. • Increase the volume. • Turn off the receiver. To avoid damaging your speakers Before you turn off the receiver, be sure to turn down the volume level. 28GB Tips Enjoying sound/images from the components connected to the receiver ?/1 ?/1 SYSTEM STANDBY Input buttons VIDEO1 VIDEO2 SAT TV BD DVD SA-CD/CD TUNER BD/DVD TOP MENU MENU F1 Enjoying a satellite tuner F2 AUDIO THEATRE DIGITAL ANALOG 1 2 3 4 5 6 7 8 9 CLEAR 0 ENTER SOUND FIELD 1 SOUND FIELD AMP MENU DISPLAY For details, refer to the operating instructions of the TV. 2 Turn the satellite tuner and the receiver on. 3 Press SAT. TOOLS/ OPTIONS 2 +/– RETURN/EXIT TV CH – PRESET – < . MENU/HOME TV CH + PRESET + < > TUNING – m You can also use INPUT SELECTOR on the receiver to select “SAT”. 4 TUNING + H M X x 5 Enjoying TV 1 Turn on the TV and choose a program. Change the TV input. For details, refer to the operating instructions of the TV. TV TV Turn on the TV. Adjust the volume of the receiver. Tip The sound may be output from the TV’s speaker. In this case, turn the volume of the TV’s speaker down to the minimum. For details, refer to the operating instructions of the TV. 2 3 4 Turn the receiver on. Press TV. Adjust the volume of the receiver. 29GB Playback TV ?/1 DMPORT AV ?/1 • When you connect a Sony TV, the audio input of the TV is switched and the image from the TV tuner is displayed on the TV screen automatically by pressing the TV button. To change this setting, see “Changing the input button assignments” (page 60). • The sound may be output from the TV’s speaker. In this case, turn the volume of the TV’s speaker down to the minimum. Enjoying Blu-ray Disc or DVD 1 2 3 Turn on the Blu-ray Disc or DVD player (recorder) and the receiver. Press DVD or BD. 5 6 Play back the disc. Adjust the volume. Tip Even if you playback Dolby True HD, Dolby Digital Plus or DTS-HD with a connected component compatible with these sound formats, the receiver accepts as Dolby Digital or DTS. When you connect the component to the receiver using an HDMI cable to playback these high-quality sound formats, set the connected component to output the sound in multi channel PCM, if possible. Enjoying a VCR 1 2 Turn on the TV. 3 Press VIDEO 1 or VIDEO 2. Turn the VCR player and the receiver on. You can also use INPUT SELECTOR on the receiver to select “VIDEO 1” or “VIDEO 2”. 30GB 5 Play back the tape on the VCR. Enjoying a Super Audio CD/CD 1 Turn on the Super Audio CD player/CD player, then place the disc on the tray. 2 3 Turn on the receiver. Press SA-CD/CD. You can also use INPUT SELECTOR on the receiver to select “SA-CD/CD”. Change the TV input. For details, refer to the operating instructions of the TV. Change the TV input. For details, refer to the operating instructions of the TV. Turn on the TV. You can also use INPUT SELECTOR on the receiver to select “DVD” or “BD”. Be sure to change the factory setting of the DVD input button on the remote so that you can use the button to control your DVD player. For details, see “Changing the input button assignments” (page 60). 4 4 4 Adjust the volume. Enjoying a connected component through DMPORT connection 1 Press DMPORT. You can also use INPUT SELECTOR on the receiver to select “DMPORT”. 2 Start playback of the connected component. Tip When listening to MP3 or other compressed music using a portable audio source, you can enhance the sound. Press SOUND FIELD repeatedly to select “P. AUDIO” (page 40). To return to the previous display Amplifier Operations Press B. Navigating through menus To exit the menu Press AMP MENU. By using the amplifier menus, you can make various adjustments to customize the receiver. 8 9 CLEAR 0 ENTER Amplifier Operations 7 SOUND FIELD AMP MENU AMP MENU TOOLS/ OPTIONS DISPLAY , V,v,B,b RETURN/EXIT 1 MENU/HOME Press AMP MENU. “SET HDMI” appears on the display. 2 Press V/v repeatedly to select the menu you want. 3 Press menu. 4 Press V/v repeatedly to select the parameter you want to adjust. 5 Press or b to enter the parameter. 6 Press V/v repeatedly to select the setting you want. 7 Press setting. or b to enter the or b to enter the 31GB Overview of the menus The following options are available in each menu. For details on navigating through menus, see page 31. Menu [Display] Parameters [Display] Settings Initial setting HDMI settings [SET HDMI] (page 35) Control for HDMIa)b) [CONTROL FOR HDMI] CTRL ON, CTRL OFF CTRL ON Volume limita) [VOL LIM] MAX, 39……1, MIN MAX Power savea) [P.SAVE] SAVE ON, SAVE OFF SAVE ON Auto Calibration settings [A.CAL] (page 35) Auto calibration starta) [START] For details, see “Performing Auto Calibration” (page 24). Clear Auto Calibration resulta)c) YES, NO [A.CAL CLR] NO Speaker settings [SP SETUP] (page 36) Center speakera) [CNT SP] CNT Y, CNT N CNT Y Surround speakersa) [SUR SP] SUR Y, SUR N SUR Y Front left speaker distancea)d) [FL DIST] FL 0.00 m to FL 7.00 m (0.10 m step) FL 3.00 m Center speaker distancea)d) [CNT DIST] CNT 0.00 m to CNT 7.00 m (0.10 m step) CNT 3.00 m 32GB Front right speaker distancea)d) FR 0.00 m to FR 7.00 m [FR DIST] (0.10 m step) FR 3.00 m Surround right speaker distancea)d) [SR DIST] SR 0.00 m to SR 7.00 m (0.10 m step) SR 3.00 m Surround left speaker distancea)d) [SL DIST] SL 0.00 m to SL 7.00 m (0.10 m step) SL 3.00 m Subwoofer distancea)d) [SW DIST] SW 0.00 m to SW 7.00 m (0.10 m step) SW 3.00 m Parameters [Display] Settings Initial setting Level settings [LEVEL] (page 37) Test tonea) [T. TONE] T. TONE N, T. TONE Y T. TONE N Front left speaker levela) [FL LVL] FL –6 dB to FL +6 dB (0.5 dB step) FL 0.0 dB Center speaker level [CNT LVL] CNT –6 dB to CNT +6 dB (0.5 dB step) CNT 0.0 dB Front right speaker level [FR LVL] FR –6 dB to FR +6 dB (0.5 dB step) FR 0.0 dB Surround right speaker level [SR LVL] SR –6 dB to SR +6 dB (0.5 dB step) SR 0.0 dB Surround left speaker level [SL LVL] SL –6 dB to SL +6 dB (0.5 dB step) SL 0.0 dB Subwoofer level [SW LVL] SW –6 dB to SW +6 dB (0.5 dB step) SW 0.0 dB Tone settings [TONE] (page 37) Bass level [BASS] BASS –6 dB to BASS +6 dB (0.5 dB step) BASS 0.0 dB Treble level [TREBLE] TRE –6 dB to TRE +6 dB (0.5 dB step) TRE 0.0 dB Custom settings [CUSTOM] (page 38) Digital broadcast language selectiona) [DUAL] MAIN, SUB, MAIN/SUB MAIN Synchronizes audio with video outputa) [A/V SYNC] SYNC OFF, SYNC 1 to SYNC 20 SYNC OFF Audio Dynamics range compressiona) [AUD. DRC] DRC OFF, DRC STD, DRC MAX DRC OFF Brightness of the displaya) [DIMMER] DIMMER Y, DIMMER N DIMMER N Displaya) [DISPLAY] DSPL ON, DSPL OFF DSPL ON Sleep timer a) [SLEEP] SLP OFF, SLP 10M, SLP 20M…. SLP 90M SLP OFF Switching the audio input modea)e) [IN MODE] AUTO, OPT AUTO continued 33GB Amplifier Operations Menu [Display] Menu [Display] Parameters [Display] Settings Initial setting S-AIR settings [S-AIR] (page 52) S-AIR IDf) [S-AIR ID] ID A, ID B, ID C ID A PAIRINGf) [PAIRING] START, CONDIN START S-AIR modef) [MODE] PARTY, SEPARATE PARTY RF Changef) [RF CHNG] RF AUTO, RF ON, RF OFF RF AUTO RF Powerf)g) [RF POWER] PWR HIGH, PWR LOW PWR HIGH S-AIR standbyf) [STBY] STBY ON, STBY OFF STBY OFF a) For details, refer to the page in the parentheses. FOR HDMI” scroll across the display, then “CONTROL” appears. c) This parameter is only available when the result of the Auto Calibration is saved. d) When the Auto Calibration result is saved, you can adjust the setting in 0.01 meter increment. e) This parameter is only available when SAT input is selected. f) This parameter is only available if the S-AIR transmitter (not supplied) is inserted to the EZW-T100 slot on the receiver. g) This parameter is only available when using the EZW-T100A wireless transceiver (for model of area code CEL, CEK only). b) “CONTROL 34GB Settings for the HDMI (SET HDMI menu) (A.CAL menu) SET HDMI menu parameters You can use the A.CAL menu to make settings for the Auto Calibration function to suit your preference. Select “A.CAL” in the amplifier menus. For details on adjusting the parameters, see “Navigating through menus” (page 31) and “Overview of the menus” (page 32). x CONTROL FOR HDMI (Control for HDMI) A.CAL menu parameters Lets you turn the Control for HDMI function on or off. For details, see “Preparing for the “BRAVIA” Sync” (page 45). x START (Auto Calibration start) x VOL LIM (Volume limit) Lets you start the Auto Calibration function. For details, see “Performing Auto Calibration” (page 24). Lets you set the volume limit of your receiver. For details, see “Using the Volume Limit function” (page 48). x A.CAL CLR (Clear Auto Calibration result) x P.SAVE (Power Save) Lets you save the power consumption during power standby mode while Control for HDMI function is set to on. For details, see “Using the Power Saving function (Power Save)” (page 49). Lets you delete the Auto Calibration result. For details on the operation, see “Clearing the measurement result” (page 26). 35GB Amplifier Operations You can use the SET HDMI menu to make various adjustments for HDMI settings. Select “SET HDMI” in the amplifier menus. For details on adjusting the parameters, see “Navigating through menus” (page 31) and “Overview of the menus” (page 32). Settings for the Auto Calibration Settings for the Speaker x SR DIST (Surround right speaker distance) (SP SETUP menu) x SL DIST (Surround left speaker distance) You can use the SP SETUP menu to set the distance of the speakers connected to this receiver. Select “SP SETUP” in the amplifier menus. For details on adjusting the parameters, see “Navigating through menus” (page 31) and “Overview of the menus” (page 32). Lets you set the distance from your listening position to the surround speakers. SP SETUP menu parameters x CNT SP (Center speaker) Lets you select the center speaker. x SUR SP (Surround speaker) Lets you select the surround speakers. x FL DIST (Front left speaker distance) x FR DIST (Front right speaker distance) Lets you set the distance from your listening position to the front speaker (A). If both front speakers are not placed an equal distance from your listening position, set the distance to the closest speaker. A 30˚ 100˚-120˚ 30˚ A 100˚-120˚ x CNT DIST (Center speaker distance) Lets you set the distance from your listening position to the center speaker. 36GB x SW DIST (Subwoofer distance) Lets you set the distance from your listening position to the subwoofer. Notes • “CNT DIST” does not appear when you set “CNT N” in the “SP SETUP” setting. • “SR DIST” and “SL DIST” do not appear when you set “SUR N” in the “SP SETUP” setting. Tip When the Auto Calibration result is saved, you can adjust the speakers distance in 1 cm steps. If the Auto Calibration result is not saved, you can adjust the speakers distance in 10 cm steps. Adjusting the tone (LEVEL menu) (TONE menu) You can use the LEVEL menu to adjust the level of each speaker. Select “LEVEL” in the amplifier menus. For details on adjusting the parameters, see “Navigating through menus” (page 31) and “Overview of the menus” (page 32). You can use the TONE menu to adjust the tonal quality (bass/treble level) of the speakers. Select “TONE” in the amplifier menus. For details on adjusting the parameters, see “Navigating through menus” (page 31) and “Overview of the menus” (page 32). LEVEL menu parameters x T. TONE (Test tone) Lets you adjust the speaker levels while listening to the test tone from your listening position. For details, see “8: Adjusting the speaker levels (TEST TONE)” (page 27). TONE menu parameters x BASS (Bass level) x TREBLE (Treble level) x FL LVL (Front left speaker level) x CNT LVL (Center speaker level) x FR LVL (Front right speaker level) x SR LVL (Surround right speaker level) x SL LVL (Surround left speaker level) x SW LVL (Subwoofer level) Notes • “CNT LVL” does not appear when you set “CNT N” in the “SP SETUP” setting. • “SR LVL” and “SL LVL” do not appear when you set “SUR N” in the “SP SETUP” setting. 37GB Amplifier Operations Adjusting the level Settings for the Custom Menu (CUSTOM menu) You can use the CUSTOM menu to make settings for the audio to suit your preference. Select “CUSTOM” in the amplifier menus. For details on adjusting the parameters, see “Navigating through menus” (page 31) and “Overview of the menus” (page 32). CUSTOM menu parameters x AUD. DRC (Audio dynamic range compression) Lets you compress the dynamic range of the sound track. This may be useful when you want to watch movies at low volumes late at night. Audio dynamic range compression is possible with Dolby Digital sources only. • DRC OFF The audio dynamic range is not compressed. • DRC STD The audio dynamic range is compressed as intended by the recording engineer. • DRC MAX The audio dynamic range is compressed dramatically. Tip x DUAL (Digital broadcast language selection) Lets you select the language you want to listen to during digital broadcast. This feature only functions for Dolby Digital sources. • MAIN (Main) Sound of the main language will be output. • SUB (Sub) Sound of the sub language will be output. • MAIN/SUB (Main/Sub) Sound of the main language will be output through the front left speaker and sound of the sub language will be output through the front right speaker simultaneously. x A/V SYNC (Synchronizes audio with video output) Audio dynamic range compression lets you compress the dynamic range of the soundtrack based on the dynamic range information included in the Dolby Digital signal. “DRC STD” is the standard setting, but it only enacts light compression. Therefore, we recommend using the “DRC MAX” setting. This greatly compresses the dynamic range and lets you view movies late at night at low volumes. Unlike analog limiters, the levels are predetermined and provide a very natural compression. x DIMMER (Brightness of the display) Lets you adjust the brightness of the display. For details, see “Changing the brightness of the display (DIMMER)” (page 50). Lets you delay the audio output so that the time gap between the audio output and visual display is minimized. You can adjust from OFF, 1 (10 ms) to 20 (200 ms) in 1 (10 ms) steps. x DISPLAY (Display) Notes Lets you set the timer to power off the receiver automatically. For details, see “Using the Sleep Timer (SLEEP)” (page 51). • You may not be able to adjust the delay between sound and image perfectly using this function. • This function is useful only for Dolby Digital, DTS and Linear PCM (2ch) input by optical and coaxial audio input signals. 38GB Lets you turn on and off the display. For details, see “Changing the display setting (DISPLAY)” (page 50). x SLEEP (Sleep timer) x IN MODE (Switching the audio input mode) Lets you set the audio input mode of inputs. For details, see “Switching the audio input mode (IN MODE)” (page 51). This parameter is only available when SAT input is selected. Settings for the S-AIR (S-AIR menu) For details on S-AIR, see “Using an S-AIR Product” (page 52). Amplifier Operations 39GB Enjoying Surround Sound 4 5 6 7 8 9 SOUND FIELD SOUND FIELD AMP MENU Selecting the sound field CLEAR 0 ENTER Press SOUND FIELD repeatedly to select the sound field you want. This receiver can create multi channel surround sound. You can select one of the optimized sound fields from the receiver’s preprogrammed sound fields. For details, see “Types of sound field available” (page 40). Types of sound field available Sound field for Sound field [Display] Effect A.F.D. mode 2CH STEREO [2CH ST] When multi channel surround formats are input, the signals are downmixed to 2 channel. A.F.D. STANDARD [A.F.D. STD] Presents the sound as it was recorded/encoded without adding any surround effects. However, this receiver will generate a low frequency signal for output to the subwoofer when there is no LFE signals. A.F.D. MULTI [A.F.D. MULT] Reproduce sound from any of the format to 2 or more speakers. PRO LOGIC [DOLBY PL] Performs Dolby Pro Logic decoding. The source recorded in 2 channel format is decoded into 4.1 channels. PRO LOGIC II MOVIE [PLII MV] Performs Dolby Pro Logic II Movie mode decoding. This setting is ideal for movies encoded in Dolby Surround. In addition, this mode can reproduce sound in 5.1 channel for watching videos of overdubbed or old movies. PRO LOGIC II MUSIC [PLII MS] Performs Dolby Pro Logic II Music mode decoding. This setting is ideal for normal stereo sources such as CDs. MOVIE-D.C.S.-a) [MV-D.C.S.-] The system reproduces the sound characteristics of the Sony Pictures Entertainment “Cary Grant Theater” cinema production studio. This is a standard mode, great for watching almost any type of movie. Movie Music Others b) a) D.C.S. SPORTS [SPORTS] Reproduces the feeling of sports broadcasting. NEWS [NEWS] The systems provided the clearer sound for the voice program such as news. PORTABLE AUDIO ENHANCER [P. AUDIO] Reproduces a clear enhanced sound image from your portable audio device. This mode is ideal for MP3 and other compressed music. HEADPHONE 2CH [HP 2CH] Output the sound from headphone left and right. Multi channel surround formats are downmixed to 2 channels. HEADPHONE THEATER [HP THEA] Output the sound as surround from headphone left and right. technology is used. For details, see “Glossary” (page 61). decoding mode appears when you connect the headphones to surround amplifier (S-Air sub unit) (not supplied). b) This 40GB Notes Tuner Operations Listening to FM/AM radio You can listen to FM and AM broadcasts through the built-in tuner. Before operation, make sure you have connected the FM and AM antennas to the receiver (page 21). Tip The tuning scale for direct tuning differs depending on the area code as shown in the following table. For details on area codes, see page 4. Area code FM AM AU, SP, TW, TH, CN 50 kHz 9 kHz* CEL, CEK 50 kHz 9 kHz * The AM tuning scale can be changed (page 43). Tuning into a station automatically (Auto Tuning) VIDEO1 VIDEO2 SAT TV BD DVD SA-CD/CD TUNER BD/DVD TOP MENU MENU F1 AUDIO THEATRE DIGITAL ANALOG Tip You can identify the encoding format of DVD software, etc., by looking at the logo on the package. TUNER F2 1 2 3 4 5 6 7 8 9 CLEAR 0 ENTER SOUND FIELD AMP MENU DISPLAY DISPLAY TOOLS/ OPTIONS , V,v,B,b MENU/ HOME RETURN/EXIT TV CH – PRESET – < . TUNING – MENU/HOME TV CH + PRESET + < > TUNING – m TUNING + H M X x TUNING + TV continued 41GB Tuner Operations • The effects provided by the virtual speakers may cause increased noise in the playback signal. • When listening with sound fields that employ the virtual speakers, you will not be able to hear any sound coming directly from the surround speakers. • This function does not work when: – signals with a sampling frequency of more than 48 kHz is input. – the multi channel Linear PCM signals are received via an HDMI IN jack. • The sound is not output from multiple speakers depending on the source. • Depending on the disc or source, the beginning of the sound may be cut off as the optimum mode is automatically selected. To avoid cutting the sound, select “A.F.D. STD.”. • When the input signal is multi channel source, Dolby Pro Logic II MOVIE/MUSIC are canceled and the multi channel source is output directly. • When the bilingual broadcast sound is input, Dolby Pro Logic II MOVIE/MUSIC are not effective. • Multi channel Linear PCM is not available for “P. AUDIO.” • Depending on the input stream, the decoding mode may not be effective. • When you select “MV-D.C.S.-” depending on the input stream, Dolby Pro Logic may be applied automatically. • When changing the sound mode while using the S-AIR receiver (not supplied), sound from the SAIR receiver (not supplied) may skip. 1 Press TUNER repeatedly to select the FM or AM band. You can also use INPUT SELECTOR on the receiver. 2 Press TUNING + or TUNING –. Press TUNING + to scan from low to high; press TUNING – to scan from high to low. The receiver stops scanning whenever a station is received. To stop the automatic tuning manually, press TUNING + or –. Presetting radio stations You can preset up to 20 FM stations and 10 AM stations. Then you can easily tune in the stations you often listen to. Presetting radio stations VIDEO1 VIDEO2 SAT TV BD DVD SA-CD/CD TUNER TUNER BD/DVD TOP MENU MENU F1 F2 AUDIO THEATRE DIGITAL ANALOG If an FM program is noisy If an FM program is noisy, you can select monaural reception. There will be no stereo effect, but reception will improve. 1 2 3 Press MENU/HOME. DISPLAY . PRESET +/– To improve reception, reorient the supplied antennas (aerials). 4 5 6 7 8 9 CLEAR 0 ENTER DISPLAY SOUND FIELD TOOLS/ OPTIONS MENU/ HOME RETURN/EXIT TV CH – PRESET – < . MENU/HOME TV CH + PRESET + < > TUNING – m TUNING + H M X x TUNING +/– TV 1 Press TUNER repeatedly to select the FM or AM band. You can also use INPUT SELECTOR on the receiver. Press MENU/HOME. Tip 3 , V,v,B,b Press V/v repeatedly to select “MONO”. Press 2 AMP MENU Press V/v repeatedly until “FM MODE” appears, then press or b. • STEREO: stereo reception. • MONO: monaural reception. The default setting is STEREO. 4 5 Numeric buttons 1 2 Press and hold TUNING + or TUNING – until the auto scanning starts. Scanning stops when the receiver tunes in a station. “ST” (for stereo program) light up in the display. 3 4 42GB Press MENU/HOME. Press V/v repeatedly until “MEMORY” appears in the display. 5 or b. Press A preset number appears in the display. 6 Press V/v repeatedly to select the preset number you want. You can select the preset number directly by pressing the number buttons. 7 Press Tuning to preset stations 1 Press TUNER repeatedly to select the FM or AM band. 2 Press PRESET + or PRESET – repeatedly to select the preset station you want. . Each time you press the button, the receiver tunes in one preset station. You can also press the numeric buttons to select the preset station you want. Then, press ENTER to enter the selection. “COMPLETE” appears in the display, and the station is stored. 8 9 Press MENU/HOME. Repeat 2 to 8 to store other stations. Restart from step 3. Changing the AM tuning interval (Except model of area code CEL, CEK) You can enter a name for preset stations. These names (for example, “XYZ”) appear in the display when a station is selected. Note that no more than one name can be entered for each preset station. 1 The AM tuning interval can be set to either 10 kHz or 9 kHz. 1 Press TUNER/BAND repeatedly until “AM” appears in the display. 2 3 Press MENU/HOME. Press V/v repeatedly until “AM STEP” appears in the display, then press or b. “9K STEP” or “10K STEP” appears in the display. 4 Press . “COMPLETE” appears in the display. The AM tuning interval is changed. 5 Press MENU/HOME. Note If you change the interval, AM preset stations will be erased. Press TUNER repeatedly to select the FM or AM band. You can also use INPUT SELECTOR on the receiver. 2 Press PRESET + or PRESET – repeatedly to select the preset station you want to create an index name for. 3 4 Press MENU/HOME. 5 6 Press Press V/v repeatedly to select “NAME IN”. . Create a name by using V/v/B/b. Press V/v repeatedly to select a character, then press b to move the cursor to the next position. Letters, numbers and other symbols can be input for a radio station name. continued 43GB Tuner Operations To change the preset number Naming preset station If you enter a wrong character Press B/b repeatedly until the character to be changed flashes, then press V/v repeatedly to select the desired character. To erase the character, press B/b repeatedly until the character to be erased flashes, then press CLEAR. 7 Press . “COMPLETE” appears in the display and the station name is stored. 8 Press MENU/HOME. Using the Radio Data System (RDS) (Models of area code CEL, CEK only) This receiver also allows you to use RDS (Radio Data System), which enables radio stations to send additional information along with the regular program signal. You can display RDS information. Notes Viewing the station name or frequency in the display When the receiver is set to “FM” or “AM”, you can check the frequency using the display. Press DISPLAY. • RDS is operable only for FM stations. • Not all FM stations provide RDS service, nor do they provide the same type of services. If you are not familiar with the RDS services in your area, check with your local radio stations for details. Receiving RDS broadcasts Each time you press DISPLAY, the display changes as shown. Station namea) y Frequencyb) Simply select a station on the FM band using automatic tuning (page 41), or preset tuning (page 42). a) This When you tune in a station that provides RDS services, the program service name* appears on the display. is displayed if you have entered a name for a preset station. b) Returns to the original display when several seconds have elapsed. Note RDS may not work properly if the station you tuned to is not transmitting the RDS signal properly or if the signal strength is weak. Displaying RDS information While receiving an RDS station, press DISPLAY repeatedly. Each time you press the button, RDS information on the display changes cyclically as follows: Program Service name t Frequency 44GB Using “BRAVIA” Sync features What is “BRAVIA” Sync? To use the “BRAVIA” Sync, set the Control for HDMI function to on for both the receiver and the connected component. The receiver is compatible with the “Control for HDMI-Easy Setting” function. When your TV is compatible with the “Control for HDMI-Easy Setting” function When you connect a Sony TV with the “Control for HDMI-Easy Setting” function, the Control for HDMI function of the receiver can be turned on simultaneously by turning the Control for HDMI function of the TV on. 1 Make sure that the receiver, TV, and playback components are connected using an HDMI cable (not supplied). (The respective components must be compatible with the Control for HDMI function.) 2 Turn on the receiver, TV and playback Control for HDMI is a mutual control function standard used by HDMI CEC (Consumer Electronics Control) for HDMI (HighDefinition Multimedia Interface). The Control for HDMI function does not work in the following cases: • When you connect the receiver to a component which does not correspond with Sony’s Control for HDMI function. • When you connect the receiver and components using other than HDMI connection. components. 3 Turn the Control for HDMI function of the TV on. The Control for HDMI function of this receiver and all the connected components are simultaneously turned on. During setup, “SCANNING” appears in the display, and once setting is completed, “COMPLETE” will appear. Wait until the setup is complete. For details on setting the TV, refer to the operating instructions supplied with the TV. We recommend that you connect the receiver to products featuring “BRAVIA” Sync. Note Depending on the connected component, the Control for HDMI function may not work. Refer to the operating instructions of the component. continued 45GB Using “BRAVIA” Sync features “BRAVIA” Sync is compatible with a Sony TV, Blu-ray Disc/DVD Player, AV amplifier, etc., that is equipped with the Control for HDMI function. By connecting Sony components that are compatible with the “BRAVIA” Sync with an HDMI cable (not supplied), operation is simplified as follows: • One-Touch Play: When you play back a component such as a DVD/Blu-ray disc player, the receiver and the TV are turned on automatically and switched to the appropriate HDMI input. Be sure that the System Audio Control setting is set to on. • System Audio Control: While watching TV, you can select to output the sound from the TV speaker or the speakers connected to the receiver. • System Power Off: When you turn off the TV, the receiver and connected components are also turned off simultaneously. Preparing for the “BRAVIA” Sync When your TV is not compatible with the “Control for HDMI-Easy Setting” function Turn the Control for HDMI function of the receiver and the connected component on individually. 7 8 9 CLEAR 0 ENTER SOUND FIELD AMP MENU DISPLAY AMP MENU TOOLS/ OPTIONS , V,v,B,b RETURN/EXIT MENU/HOME 1 Perform the steps given in “When your TV is compatible with the “Control for HDMI-Easy Setting” function” (page 45). 2 Press AMP MENU. “SET HDMI” appears on the display. 3 Press or b to enter the menu. 4 Press V/v repeatedly to select “CONTROL FOR HDMI”. “CONTROL FOR HDMI” scrolls across the display, then “CONTROL” appears. 5 Press or b to enter the parameter. 6 Press V/v repeatedly to select “CTRL ON”. Control for HDMI function is activated. 7 Set the Control for HDMI function of the connected component to on. 8 Select the HDMI input (BD, DVD, SAT) of the receiver and TV to match the HDMI output of the connected component, so that the image from the connected component is displayed. For details on setting the TV and connected components, refer to the operating instructions of the respective components. 46GB Notes • You cannot perform One-Touch Play and System Audio Control during Control for HDMI-Easy Setting operation. • Before you do the Control for HDMI-Easy Setting from the TV, be sure to turn on the TV, connected components and receiver. • When you unplug the HDMI cable or change the connection, perform the steps given in “When your TV is compatible with the “Control for HDMIEasy Setting” function” (page 45) or “When your TV is not compatible with the “Control for HDMIEasy Setting” function” (page 46). • If the playback components cannot function after you have made the settings for Control for HDMIEasy Setting, check the Control for HDMI setting on your TV. • If the connected components do not support the Control for HDMI-Easy Setting, you need to set the Control for HDMI function for the connected components to on before you perform the Control for HDMI-Easy Setting from the TV. Playing back components with one-touch operation (One-Touch Play) You can enjoy sound and image from the components connected to the receiver via HDMI connections by a simple operation. Play back a connected component. The receiver and the TV are turned on automatically and switched to the appropriate HDMI input. Note Be sure that the System Audio Control setting is set to on. Watching a DVD/Blu-ray disc by simple operation Note Depending on the TV, the start of the content may not be output. Tip You can enjoy the components that are connected to the HDMI jacks, even if you turn the receiver off. The ACTIVE STANDBY indicator lights up in amber. (System Audio Control) You can enjoy the TV sound from the speakers connected to the receiver by a simple operation. You can operate System Audio Control function using the TV menu. For details, refer to the operating instructions supplied with the TV. When System Audio Control function is turned on, the receiver will turns on and switches to the appropriate input automatically. TV sound is output from the speakers connected to the receiver, and the volume of the TV is minimized simultaneously. You can use the System Audio Control function as follows. • If you turn on the receiver while the TV is turned on, the System Audio Control function will automatically be set to on and the TV sound will output from the speakers connected to the receiver. However, if you turn off the receiver, the sound will output from the TV speakers. • You can adjust the receiver’s volume when you adjust the TV volume. Notes • If System Audio Control does not function according to your TV setting, refer to the operating instructions supplied with the TV. • When you connect a TV that does not have System Audio Control function, the System Audio Control function does not work. • If the TV is turned on before turning on the receiver, the TV sound will not be output for a moment. 47GB Using “BRAVIA” Sync features You can also select a connected component, such as a DVD/Blu-ray disc player using the TV menu. In this case, the receiver and the TV switch to the appropriate HDMI input. Enjoying the TV sound from the speakers connected to the receiver Using the Volume Limit function When the System Audio Control function is active, and the output method changes from the TV speaker to the speakers connected to the receiver automatically, loud sound may be output depending on the volume level of the receiver. You can prevent this by limiting the maximum volume level. 1 2 3 4 Press AMP MENU. Press v/V repeatedly until “SET HDMI” appears, then press or b. Turning off the receiver with the TV (System Power Off) When you turn the TV off by using the POWER button on the TV’s remote, the receiver and the connected components turn off automatically. You can also use the receiver’s remote to turn off the TV. TV ?/1 DMPORT AV ?/1 ?/1 SYSTEM STANDBY Press v/V repeatedly until “VOL LIM” appears, then press or b. VIDEO1 VIDEO2 SAT TV BD SA-CD/CD TUNER BD/DVD TOP MENU MENU F1 F2 AUDIO THEATRE DIGITAL ANALOG Press v/V repeatedly to select the maximum volume level you want. The maximum volume level changes as follows: TV ?/1 DVD 1 2 3 4 5 6 7 8 9 CLEAR 0 SOUND FIELD AMP MENU DISPLAY ENTER TOOLS/ OPTIONS MAX y 39 y 38 y ...... y 2 y 1 y MIN 5 Press AMP MENU. RETURN/EXIT TV CH – PRESET – < . The AMP MENU turns off. Notes • This function is available only when the Control for HDMI function is set to on. • This function is not available when the output method changes from the speakers connected to the receiver to the TV speaker. Tips • Sony recommends that you set the maximum volume level to a little lower than the volume you usually listen to. • Regardless of the maximum volume level you set, the MASTER VOLUME on the receiver and the 2 +/– button of the remote are operable. • If you do not want to limit the maximum volume level, select “MAX.” 48GB MENU/HOME TV CH + PRESET + < > TUNING – m TUNING + H M X x TV TV Press TV and TV ?/1 at the same time. The TV, receiver and the components connected via HDMI are turned off. Notes • Set the TV Standby Synchro to “ON” before using the System Power Off function. For details, refer to the operating instructions supplied with the TV. • Depending on the status, the connected components may not be turned off. For details, refer to the operating instructions supplied with the connected components. Notes Using the Power Saving function (Power Save) You can reduce the receiver’s power consumption when you connect a “BRAVIA” Sync-compatible TV to this receiver during active standby mode if the TV is turned off and HDMI signal transmission is stopped. 4 5 6 7 8 9 CLEAR 0 ENTER • The power saving function may not work for some TVs compatible with the “BRAVIA” Sync. In this case, set “P.SAVE” to “SAVE OFF.” • Depending on your components, it may take time before image or sound is output. • This function is available only when the Control for HDMI function is set to on. SOUND FIELD AMP MENU AMP MENU TOOLS/ OPTIONS DISPLAY , V,v,B,b MENU/HOME TV CH + PRESET + < > TUNING – m 1 Using “BRAVIA” Sync features RETURN/EXIT TV CH – PRESET – < . TUNING + H M Press AMP MENU. “SET HDMI” appears on the display. 2 Press menu. 3 Press V/v repeatedly to select “P.SAVE”, then press or b. 4 Press V/v repeatedly to select the setting, then press or b. or b to enter the • SAVE ON: Reduces power consumption in standby mode. HDMI signal transmission occurs only when the TV is on. • SAVE OFF: No reduction. HDMI signal transmission occurs continuously. 5 Press AMP MENU. The AMP MENU turns off. 49GB Other Operations Changing the brightness of the display (DIMMER) Changing the display setting (DISPLAY) You can change the display setting. 1 You can change the brightness of the display. 1 “SET HDMI” appears on the display. 2 Press V/v repeatedly until “CUSTOM” appears, then press or b. Press V/v repeatedly until “CUSTOM” appears, then press or b. 3 Press V/v repeatedly until “DIMMER” appears, then press or b. Press V/v repeatedly until “DISPLAY” appears, then press or b. 4 Press V/v repeatedly to change the display setting, then press . Press AMP MENU. “SET HDMI” appears on the display. 2 3 4 Press V/v repeatedly to select the brightness of the display, then press . • DIMMER Y: Low lighting. • DIMMER N: Bright lighting. 5 Press AMP MENU. The AMP menu turns off. 50GB Press AMP MENU. • DSPL ON: The display appears all the time. • DSPL OFF: The display appears when you operate the receiver. 5 Press AMP MENU. The AMP menu turns off. Using the Sleep Timer (SLEEP) You can set the receiver to turn off at a preset time when you sleep while listening to music. You can preset the time in 10 minutes decrements. 1 Press AMP MENU. “SET HDMI” appears on the display. 2 3 4 (IN MODE) You can select the audio input mode setting when you connect satellite tuner or set-top box to both HDMI IN jack and optical digital input jack on the receiver and SAT input has been selected. 1 Press AMP MENU. “SET HDMI” appears on the display. 2 Press V/v repeatedly until “SLEEP” appears, then press or b. Press V/v repeatedly to select “CUSTOM”. 3 Press menu. Press V/v repeatedly to select the preset time. 4 Press V/v repeatedly to select “IN MODE”. The minutes display (the remaining time) changes as follows: 5 SLP OFF y SLP 10M y SLP 20M Y Y SLP 90M y SLP 80M ...... SLP 30M Press or b to enter the parameter. 6 Press V/v repeatedly to select the audio input mode you want. 7 Press AMP MENU. Press . Press AMP MENU. or b to enter the The AMP menu turns off. The AMP menu turns off. Audio input modes x AUTO Gives priority to HDMI audio signals if there are both digital (HDMI and optical) connections. x OPT Specifies the digital audio signals input to the DIGITAL SAT OPT IN jack. 51GB Other Operations 5 6 Press V/v repeatedly until “CUSTOM” appears, then press or b. Switching the audio input mode Using an S-AIR Product This receiver is compatible with the S-AIR function (page 62), which allows wireless sound transmission between S-AIR products. When you purchase the S-AIR product, you need to perform the following settings to establish the sound transmission. Room B S-AIR sub unit (S-AIR receiver) Room A S-AIR main unit (this receiver) INPUT SELECTOR ?/1 MASTER VOLUME ACTIVE STANDBY About S-AIR products There are two types of S-AIR product. • S-AIR main unit (this receiver): The S-AIR main unit is for transmitting sound. You can use up to 3 S-AIR main units. (The number of usable S-AIR main unit depends on the use environment.) • S-AIR sub unit (not supplied): The S-AIR sub unit is for receiving sound. – Surround amplifier: You can enjoy surround speaker sound wirelessly. – S-AIR receiver: You can enjoy system sound in another room. These S-AIR products can be purchased as an option (the S-AIR products lineup differs depending on the area). Notes or instruction from the surround amplifier or S-AIR receiver in this operating instructions is refer only when the surround amplifier or S-AIR receiver is used. S-AIR sub unit (surround amplifier) Inserting the wireless transmitter/transceiver To make use of the S-AIR function, you need to insert the wireless transmitter (not supplied) into the S-AIR main unit and the wireless transceiver (not supplied) into the S-AIR sub unit. Notes • Before inserting the wireless transmitter/ transceiver, be sure to disconnect the AC power cord (mains lead). • Do not touch the terminals of the wireless transmitter/transceiver. 52GB To insert the wireless transmitter into the S-AIR main unit 1 Remove the screws and detach the slot cover. Notes • Insert the wireless transmitter with the S-AIR logo facing up. • Insert the wireless transmitter so that the V marks are aligned. • Do not insert other than the wireless transmitter into the EZW-T100 slot. 3 Use the screws that you removed from Slot cover step 1 to fasten the wireless transmitter. 0 -T10 EZW 0 -T10 EZW L EZW-T100 R AUTO AUDIO IN CAL MIC VIDEO 1 DC5V 700mA MAX DMPORT • Remove the screws from the slot cover bearing the caution mark. Do not remove other screws. • The slot cover is no longer necessary. However, keep it after detaching. 2 Insert the wireless transmitter. Do not use other screws to fasten the wireless transmitter. To insert the wireless transceiver into the S-AIR sub unit For details on installing the wireless transceiver into the surround amplifier and S-AIR receiver, refer to the operating instructions supplied with the surround amplifier and S-AIR receiver. EZW-T100 slot 0 -T10 EZW Wireless transmitter 53GB Other Operations Notes Note Establishing sound transmission between the S-AIR main unit and S-AIR sub unit (ID setting) When you match the ID of the S-AIR main unit and the S-AIR sub unit, you can establish sound transmission. You can use multiple S-AIR products by setting a different ID for each unit. 4 7 8 SOUND FIELD 9 AMP MENU CLEAR 0 For details on setting the ID of the surround amplifier and S-AIR receiver, refer to operating instructions supplied with the surround amplifier and S-AIR receiver. Sound transmission is established as follows (example): ENTER INPUT SELECTOR ?/1 MASTER VOLUME ACTIVE STANDBY ID A ID B AMP MENU TOOLS/ OPTIONS DISPLAY , V/v/b ID A RETURN/EXIT TV CH – PRESET – < . MENU/HOME TV CH + PRESET + < > TUNING – S-AIR sub unit ID A S-AIR sub unit ID B S-AIR sub unit TUNING + m H M To set the ID of the S-AIR main unit 1 2 Press AMP MENU. 3 Press menu. 4 Press V/v repeatedly to select “S-AIR ID”. 5 Press or b to enter the parameter. 6 Press V/v repeatedly to select the desired ID (A, B or C) then press . Press V/v repeatedly to select “S-AIR”. or b to enter the To exit the menu Press AMP MENU. 54GB Other S-AIR main unit S-AIR main unit 6 5 To set the ID of the S-AIR sub unit Pairing the S-AIR main unit with a specific S-AIR sub unit (Pairing operation) To establish sound transmission, you need to set the same ID for your S-AIR main unit and S-AIR sub unit. However, if your neighbors have S-AIR products and their IDs are the same as yours, your neighbors could receive the sound of your S-AIR main unit or vice versa. To prevent this, you can pair the S-AIR main unit with a specific S-AIR sub unit by performing the pairing operation. 2 x Before pairing Sound transmission is established by the ID (example). Your room • To set the ID of the S-AIR main unit, see “To set the ID of the S-AIR main unit” (page 54). • To set the ID of the S-AIR sub unit, refer to the operating instructions supplied with the S-AIR sub unit. Neighbor S-AIR main unit INPUT SELECTOR ?/1 MASTER VOLUME ACTIVE STANDBY ID A ID A ID A S-AIR sub unit S-AIR sub unit x After pairing Sound transmission is established between the paired S-AIR main unit and S-AIR sub unit(s) only. Your room Neighbor 3 4 Press AMP MENU. 5 Press menu. 6 Press V/v repeatedly to select “PAIRING”. 7 Press or b to enter the parameter. 8 Press V/v repeatedly to select the setting you want, then press . S-AIR main unit INPUT SELECTOR ?/1 MASTER VOLUME ACTIVE STANDBY ID A ID A S-AIR sub unit Pairing 1 Place the S-AIR sub unit that you want to pair near the S-AIR main unit. Note Remove headphones from the surround amplifier (if connected). or b to enter the • START: The S-AIR main unit starts pairing. • CONDIN: you can check the current ID. When the pairing setting is timed out, “NO PAIR” appears in the display. No transmission S-AIR sub unit Press V/v repeatedly to select “S-AIR”. 9 Start pairing of the S-AIR sub unit. x For the surround amplifier Refer to the operating instructions supplied with surround amplifier. x For the S-AIR receiver Refer to the operating instructions supplied with S-AIR receiver. 10 Pairing completed. “COMPLETE” appears in the display. To exit the menu Press AMP MENU. continued 55GB Other Operations ID A Match the IDs of the S-AIR main unit and the S-AIR sub unit. 1 Note Perform the pairing within several minutes after step 8. Otherwise, the pairing is canceled automatically and the “INCOMP” display appears. • To set the ID of the S-AIR main unit, see “To set the ID of the S-AIR main unit” (page 54). • To set the ID of the S-AIR receiver, refer to the operating instructions supplied with S-AIR receiver. To cancel pairing Reset the ID of the S-AIR main unit. For details, see “To set the ID of the S-AIR main unit” (page 54). You can set the same ID as before. Notes • When you are using another S-AIR sub unit, such as a surround amplifier, do not change the ID of the S-AIR main unit. Set the ID of the S-AIR receiver to the match the ID of the S-AIR main unit. • When you pair the S-AIR main unit and another S-AIR sub unit, such as a surround amplifier, you also need to pair between the S-AIR main unit and the S-AIR receiver. For details, see “Pairing the S-AIR main unit with a specific S-AIR sub unit (Pairing operation)” (page 54). Enjoying the system’s sound in another room (For the S-AIR receiver only (not supplied)) You can enjoy the system’s sound in another room by using the S-AIR receiver. The S-AIR receiver can be placed in another room for enjoying the system’s sound there. For details of the S-AIR receiver, refer to the operating instructions supplied with S-AIR receiver. Note Sources with copyright protection may not be playable on S-AIR products. 4 5 6 7 8 9 CLEAR 0 ENTER SOUND FIELD AMP MENU DISPLAY TOOLS/ OPTIONS , V,v,B,b RETURN/EXIT TV CH – PRESET – < . MENU/HOME TV CH + PRESET + < > TUNING – m 56GB TUNING + H M AMP MENU Set the ID of the S-AIR receiver to match the S-AIR main unit. 2 3 Press AMP MENU. 4 Press menu. 5 Press V/v repeatedly to select “MODE”. 6 Press or b to enter the parameter. Press V/v repeatedly to select “S-AIR”. or b to enter the 7 Press V/v repeatedly to select the setting you want. • PARTY: The S-AIR sub unit outputs sound according to function set on the S-AIR main unit. • SEPARATE: You can select the input you want for the S-AIR receiver while the input of the S-AIR main unit remain unchanged. When “SEPARATE” is set, the functions you can select are “MAIN UNIT”, “SACD/CD”, “TUNER FM”, “TUNER AM” and “DMPORT”. To enjoy the same function as the S-AIR main unit, select “MAIN UNIT”. 8 Changing the channel for better sound transmission If you use multiple wireless systems which sharing the 2.4 GHz band, such as wireless LAN or Bluetooth, the transmission of S-AIR products or other wireless systems may be unstable. In this case, the transmission may be improved by changing the following “RF CHNG” setting. 5 6 7 8 9 CLEAR 0 Notes AMP MENU , V,v,B,b RETURN/EXIT TV CH – PRESET – < . MENU/HOME TV CH + PRESET + < > TUNING – m TUNING + H M 1 2 Press AMP MENU. 3 Press menu. 4 Press V/v repeatedly to select “RF CHNG”. 5 Press or b to enter the parameter. Press V/v repeatedly to select “S-AIR”. or b to enter the continued 57GB Other Operations • When the sound is other than 2 channel stereo, multi channel sound is downmixed to 2 channel. • When “TUNER FM” or “TUNER AM” is selected on the receiver, you can only select the same band for the tuner on the S-AIR product. ENTER TOOLS/ OPTIONS DISPLAY Select the desired function on the S-AIR product. Adjust the volume on the S-AIR receiver. SOUND FIELD AMP MENU When the sound is other than 2 channel stereo, multi channel sound is down mixed to 2 channel. 9 4 6 Press V/v repeatedly to select the setting you want, then press . • RF AUTO: Normally select this. The system change “RF CHNG” to “RF ON” or “RF OFF” automatically. • RF ON: The system transmits sound by searching the better channel for transmitting. • RF OFF: The system transmits sound by fixing the channel for transmitting. To exit the menu Press AMP MENU. Changing the RF output power (For EZW-T100A wireless transceiver only) 1 2 Press AMP MENU. 3 Press menu. 4 Press V/v repeatedly until “RF POWER” appears in the front panel display, then press or b. 5 Press V/v to select the desired setting. Notes • When the wireless transmitter is not inserted in the S-AIR main unit, you cannot set “RF CHNG”. • In most cases, you will not need to change this setting. • If “RF CHNG” is set to “RF OFF,” transmission between the S-AIR main unit and S-AIR sub unit can be performed using one of the following channels. – S-AIR ID A: equivalent channel for IEEE 802.11b/g channel 1 – S-AIR ID B: equivalent channel for IEEE 802.11b/g channel 6 – S-AIR ID C: equivalent channel for IEEE 802.11b/g channel 11 • The transmission may be improved by changing the transmission channel (frequency) of the other wireless system(s). For details, refer to the operating instructions of the other wireless system(s). 58GB Press V/v repeatedly to select “S-AIR”. or b to enter the • “HIGH”: Normally select this. • “LOW”: The RF output power is decreased. 6 Press . The setting is made. 7 Press AMP MENU. The receiver menu turns off. Enjoying the S-AIR receiver while the S-AIR main unit is in standby mode (For the S-AIR receiver only (not supplied)) You can enjoy the S-AIR receiver while the S-AIR main unit is in standby mode by setting “STBY” to “STBY ON”. 4 5 6 7 8 9 CLEAR 0 SOUND FIELD AMP MENU ENTER AMP MENU TOOLS/ OPTIONS DISPLAY To exit the menu Press AMP MENU. Notes • When you set “STBY” to “STBY ON”, the power consumption increases during the standby mode. • When the wireless transmitter is not inserted in the S-AIR main unit, you cannot set “STBY”. • When the wireless transmitter is removed from the S-AIR main unit, “STBY” is set to “STBY OFF” automatically. • When you turn the system off while “STBY” is set to “STBY ON”, you cannot use any buttons other than ?/1 button. • The sound of the S-AIR receiver may be cut off by operation of the S-AIR main unit. , V,v,B,b RETURN/EXIT TV CH – PRESET – < . MENU/HOME TV CH + PRESET + < > TUNING – m TUNING + H M 1 2 Press AMP MENU. 3 Press menu. 4 Press V/v repeatedly to select “STBY”. 5 Press or b to enter the parameter. 6 Press V/v repeatedly to select the setting you want, then press . Other Operations Press V/v repeatedly to select “S-AIR”. or b to enter the • STBY OFF: You cannot enjoy the S-AIR receiver while the S-AIR main unit is in standby mode. • STBY ON: You can enjoy the S-AIR receiver while the S-AIR main unit is in standby mode or turned on. 59GB 2 Using the Remote Changing the input button assignments You can change the factory settings of the input buttons to suit the components in your system. For example, if you connect a Blu-ray Disc player to the DVD jack on the receiver, you can set the DVD button on this remote to control the Blu-ray Disc player. You cannot assign any component other than a TV to the TV (white) button of the remote. Notes • You can change the remote assignments for BD, DVD and SAT input buttons. • When the receiver is in VIDEO1, VIDEO2 or SA-CD/CD mode, you cannot operate the selected component. TV ?/1 DMPORT AV ?/1 ?/1 ?/1 DMPORT TV (white) VIDEO2 SAT TV BD/DVD TOP MENU MENU BD DVD SA-CD/CD TUNER F1 Input buttons F2 AUDIO THEATRE 1 2 3 4 5 6 7 8 9 CLEAR 0 SOUND FIELD AMP MENU DISPLAY ENTER TOOLS/ OPTIONS 2– RETURN/EXIT 1 MENU/HOME Hold down the input button of which you want to change the assignment. Example: Hold down DVD. 60GB Example: Press 3. Now you can use the DVD button to control the Blu-ray Disc player. Categories and the corresponding buttons for BD, DVD, and SAT Categories Press DVD player (command mode DVD1) 1 DVD recorder (command mode DVD3)a) 2 Blu-ray disc player (command mode BD1)b) 3 Blu-ray disc recorder (command mode BD3) 4 Euro Digital Satellite Receiverc) 7 SYSTEM STANDBY VIDEO1 DIGITAL ANALOG Numeric button Referring to the following table, press the corresponding button for the category you want. a) The default setting of the DVD button. Sony DVD recorders are operated with a DVD1 or DVD3 setting. For details, refer to the operating instructions of the DVD recorders. b) The default setting of the BD button. For details on the BD1 or BD3 setting, refer to the operating instructions of the Blu-ray Disc player or Blu-ray Disc recorder. c) The default setting of the SAT button. Categories and the corresponding buttons for TV Categories Press TV d) 5 TV e) 6 d) The default setting of the TV (white) button. When this setting is selected, the audio input of the TV is switched and the image from the TV tuner is displayed on the TV screen automatically by pressing the TV (white) button. e) When this setting is selected, the audio input of the TV is switched automatically by pressing the TV (white) button. To clear all remote button assignments Press and hold 2 –, then press ?/1 and DMPORT at the same time. The remote is reset to its factory settings. Additional Information Glossary x Digital Cinema Sound (DCS) A unique sound reproduction technology for home theater developed by Sony, in cooperation with Sony Pictures Entertainment, for enjoying the exciting and powerful sound of movie theaters at home. With this “Digital Cinema Sound” developed by integrating a DSP (Digital Signal Processor) and measured data, the ideal sound field intended by filmmakers can be experienced at home. x Dolby Digital Digital audio encoding/decoding technology developed by Dolby Laboratories, Inc. It consists of front (Left/Right), center, surround (Left/Right) and subwoofer channels. It is a designated audio standard for DVD-video and also known as 5.1 channel surround. Since surround information is recorded and reproduced in stereo, more realistic sound with fuller presence is delivered than with Dolby surround. This technology converts 2 channel stereo recorded audio into 5.1 channel for playback. There is a MOVIE mode for movies and MUSIC mode for stereo sources such as music. Old movies encoded in the traditional stereo format can be enhanced with 5.1 channel surround sound. x Dolby Surround (Dolby Pro Logic) Audio processing technology developed by Dolby Laboratories, Inc. Center and mono surround information is matrixed into two stereo channels. When reproduced, audio is decoded and output in 4 channel surround sound. This is the most common audio processing method for DVD-video. continued 61GB Using the Remote/Additional Information x Dolby Pro Logic II x DTS Digital Surround Digital audio encoding/decoding technology for theaters developed by DTS, Inc. It compresses audio less than Dolby Digital, delivering a higher quality sound reproduction. x HDMI (High-Definition Multimedia Interface) HDMI (High-Definition Multimedia Interface) is an interface that supports both video and audio on a single digital connection, allowing you to enjoy high quality digital picture and sound. The HDMI specification supports HDCP (High-bandwidth Digital Contents Protection), a copy protection technology that incorporates coding technology for digital video signals. x S-AIR (Sony Audio Interactive Radio frequency) Recent times have seen the rapid spread of DVD media, Digital Broadcasting, and other high-quality media. To ensure that the subtle nuances of these high-quality media are transmitted with no deterioration, Sony has developed a technology called “S-AIR” for the radio transmission of digital audio signals with no compression, and has incorporated this technology into the EZW-T100. This technology transfers digital audio signals with no compression using the 2.4 GHz band range of ISM band (Industrial, Scientific, and Medical band), such as wireless LANs and Bluetooth applications. x S-master x L.F.E. (Low Frequency Effects) Sound effects of low frequencies which are output from a subwoofer in Dolby Digital or DTS, etc. By adding a deep bass with a frequency between 20 to 120 Hz, audio becomes more powerful. x Sampling frequency To convert analog audio to digital, analog data should be quantified. This process is called sampling, and the number of times per second the analog data is quantified is called the sampling frequency. A standard music CD stores data quantified at 44,100 times per second, which is expressed as a sampling frequency of 44.1 kHz. Generally speaking, a higher sampling frequency means better sound quality. S-master is an all-digital amplifier technology developed by Sony, which effectively minimizes the occurrence of sound fragmentation and jitter, delivering superb dialog clarity and faithful reproduction of the original sound. The compact amplifier section supports a higher power efficiency and improved thermal performance. x TSP (Time Stretched Pulse) A TSP signal is a highly precise measuring signal that utilizes impulse energy, measuring a wide band, from low to high, in a short period. The amount of energy used to measure signals is important to ensure measurement accuracy in a normal indoor environment. Using TSP signals makes it possible to measure signals effectively. x x.v.Colour x.v.Colour is a more familiar term for the xvYCC standard proposed by Sony, and is a trademark of Sony. xvYCC is an international standard for colour space in video. This standard can express a wider colour range than the currently used broadcast standard. 62GB On placement Precautions On safety Should any solid object or liquid fall into the cabinet, unplug the receiver and have it checked by qualified personnel before operating it any further. On power sources • Before operating the receiver, check that the operating voltage is identical with your local power supply. The operating voltage is indicated on the nameplate on the back of the receiver. • The unit is not disconnected from the AC power source (mains) as long as it is connected to the wall outlet, even if the unit itself has been turned off. • If you are not going to use the receiver for a long time, be sure to disconnect the receiver from the wall outlet. To disconnect the AC power cord, grasp the plug itself; never pull the cord. • The AC power cord must be changed only at a qualified service shop. • Place the receiver in a location with adequate ventilation to prevent heat buildup and prolong the life of the receiver. • Do not place the receiver near heat sources, or in a place subject to direct sunlight, excessive dust, or mechanical shock. • Do not place anything on top of the cabinet that might block the ventilation holes and cause malfunctions. • Do not place the receiver near equipment such as a TV, VCR, or tape deck. If the receiver is being used in combination with a TV, VCR, or tape deck, and is placed too close to that equipment, noise may result, and picture quality may suffer. This is especially likely when using an indoor antenna. Therefore, we recommend using an outdoor antenna. • Use caution when placing the receiver or speakers on surfaces that have been specially treated (with wax, oil, polish, etc.) as staining or discoloration of the surface may result. On operation Before connecting other components, be sure to turn off and unplug the receiver. On heat buildup If you encounter color irregularity on a nearby TV screen The center speaker is magnetically shielded to allow it to be installed near a TV set. However, color irregularities may still be observed on certain types of TV sets. As the front, surround speakers and subwoofer are not magnetically shielded, we recommend that you place the surround speakers and subwoofer slightly further away from TV set (page 13). If color irregularity is observed... Turn off the TV set, then turn it on again after 15 to 30 minutes. continued 63GB Additional Information Although the receiver heats up during operation, this is not a malfunction. If you continuously use this receiver at a large volume, the cabinet temperature of the top, side and bottom rises considerably. To avoid burning yourself, do not touch the cabinet. If color irregularity is observed again... Place the speaker further away from the TV set. If howling occurs Reposition the speakers or turn down the volume on the receiver. Troubleshooting If you experience any of the following difficulties while using the receiver, use this troubleshooting guide to help you remedy the problem. Audio On cleaning Clean the cabinet, panel, and controls with a soft cloth slightly moistened with a mild detergent solution. Do not use any type of abrasive pad, scouring powder, or solvent, such as alcohol or benzine. If you have any questions or problems concerning your receiver, please consult your nearest Sony dealer. There is no sound, no matter which component is selected, or only a very low-level sound is heard. • Check that the speakers and components are connected securely. • Check that both the receiver and all components are turned on. • Check that MASTER VOLUME is not set to “VOL MIN”. • Press to cancel the muting function. • Check that you have selected the correct component with the input buttons. • The protective device on the receiver has been activated. Turn off the receiver, eliminate the short-circuit problem, and turn on the power again. • Check that the IN MODE setting is correct for SAT input. There is no sound from a specific component. • Check that the component is connected correctly to the audio input jacks for that component. • Check that the cord(s) used for the connection is (are) fully inserted into the jacks on both the receiver and the component. There is no sound from one of the front speakers. • Make sure you have connected to both the L and R jacks of an analog component, and not only to either the L or R jack. Use an audio cord (not supplied). 64GB There is no sound from digital sources (from OPTICAL input jack). • Check that the IN MODE is set to “AUTO” for SAT input. There is severe hum or noise. • Check that the speakers and components are connected securely. • Check that the connecting cords are away from a transformer or motor, and at least 3 meters away from a TV set or fluorescent light. • Move your audio components away from the TV. • The plugs and jacks are dirty. Wipe them with a cloth slightly moistened with alcohol. There is pop noise from a specific component connected to this receiver when you turn on the component. • Check that the IN MODE is set to “AUTO” for SAT input (page 51). There is no sound, or only a very lowlevel sound is heard from the center/ surround speakers. • Select a MOVIE-D.C.S.- mode (page 40). • Adjust the speaker level (page 27). • Check that the speakers are connected securely. The surround effect cannot be obtained. • Make sure the sound field function is on (press SOUND FIELD). • Sound fields do not function for signals with a sampling frequency of more than 48 kHz. There is no sound from the component connected to the DIGITAL MEDIA PORT adapter. • Adjust the volume of this receiver. • The DIGITAL MEDIA PORT adapter and/or component is not connected correctly. Turn off the receiver, then reconnect the DIGITAL MEDIA PORT adapter and/or component. • Check the DIGITAL MEDIA PORT adapter and/or component device to make sure it supports this receiver. Video There is no picture or an unclear picture appears on the TV screen or monitor. • Make sure you have connected the video output of your video component to the TV. • Move your audio components away from the TV. • Depending on the DIGITAL MEDIA PORT adapter, video output may not be possible. continued 65GB Additional Information There is no sound from the subwoofer. • Check that the subwoofer is connected correctly and securely. Dolby Digital or DTS multi channel sound is not reproduced. • Check that the DVD, etc. you are playing is recorded in Dolby Digital or DTS format. • When connecting the DVD player, etc., to the digital input jacks of this receiver, check the audio setting (the settings for the audio output) of the connected component. HDMI The volume turns down when the output method changes from the TV speaker to the speakers connected to the receiver. • The Volume Limit function is working. For details, see “Using the Volume Limit function” (page 48). The source sound input to the HDMI jack on the receiver is not output from the receiver or the TV speaker. • Check the setting of CONTROL FOR HDMI in the SET HDMI menu (page 35). • Check the HDMI connection (page 19). • You cannot listen to the Super Audio CD by connecting HDMI. • Depending on the playback component, you may need to set up the component. Refer to the operating instructions supplied with each component. The source image input to the HDMI jack on the receiver is not output from the TV. • Check the HDMI connection (page 19). • Depending on the playback component, you may need to set up the component. Refer to the operating instructions supplied with each component. The control for HDMI function does not work. • Check the HDMI connection (page 19). • Make sure “CONTROL FOR HDMI” is set to “CTRL ON” in SET HDMI menu. • Make sure the connected component is compatible with the Control for HDMI function. • Check the Control for HDMI settings on the connected component. Refer to the operating instructions of the connected component. • Repeat the procedures of “Preparing for the “BRAVIA” Sync” if you change the HDMI connection, connect/disconnect the AC power cord, or there is a power failure (page 45). 66GB No sound is output from the receiver and TV speaker while using the System Audio Control function. • Make sure the TV is compatible with the System Audio Control function. • If you cannot listen to the sound of a component connected to the receiver – Select the appropriate input when you want to watch a program on a component connected via HDMI connection to the receiver. – Change the TV channel when you want to watch a TV broadcast. – Select the component or input you want to watch when you watch a program on the component connected to the TV. Refer to the operating instructions of the TV on this operation. When the receiver is in standby mode, there is no image or sound on the TV. • When the receiver is in standby mode, image and sound are output from the HDMI component selected the last time you turned off the system. If you are enjoying other component, play the component and perform the One-Touch Play operation, or turn on the system to select the HDMI component you want to enjoy. • Make sure “P.SAVE” is set to “SAVE OFF” in the SET HDMI menu if you connect component not compatible with the “BRAVIA” Sync to the receiver (page 49). S-AIR function S-AIR connection is not established (sound transmission is not established), e.g., the indicator of the S-AIR sub unit turns off, flashes, or turns red. • If you use another S-AIR main unit, place it more than 8 m away from this S-AIR main unit. • Confirm the S-AIR IDs of the S-AIR main unit and S-AIR sub unit (page 54). • Another S-AIR sub unit is paired to the S-AIR main unit. Pair the desired S-AIR sub unit with the S-AIR main unit (page 54). • The S-AIR main unit is paired to another S-AIR sub unit. Cancel pairing. • Place the S-AIR main unit and S-AIR sub unit separately from other wireless devices. • Avoid using any other wireless devices. • The S-AIR sub unit is turned off. Make sure the AC power cord (mains lead) is connected and turn on the S-AIR sub unit. Tuner The FM reception is poor. • Use a 75-ohm coaxial cable (not supplied) to connect the receiver to an outdoor FM antenna as shown below. If you connect the receiver to an outdoor antenna, ground it against lightning. To prevent a gas explosion, do not connect the ground wire to a gas pipe. Outdoor FM antenna Receiver ANTENNA Additional Information No sound is heard from the S-AIR product. • If you use another S-AIR main unit, place it more than 8 m away from this S-AIR main unit. • Confirm the S-AIR IDs of the S-AIR main unit and S-AIR sub unit (page 54). • Confirm the pairing setting (page 54). • Place the S-AIR main unit and S-AIR sub unit closer to each other. • Avoid use of equipment that generates electromagnetic energy, such as a microwave oven. • Place the S-AIR main unit and S-AIR sub unit separately from other wireless devices. • Avoid using any other wireless devices. • Change the “RF CHNG” setting (page 57). • Change the S-AIR ID settings of the S-AIR main unit and S-AIR sub unit. • Turn off the receiver and S-AIR sub unit, then turn on again. There is noise or the sound skips. • If you use another S-AIR main unit, place it more than 8 m away from this S-AIR main unit. • Place the S-AIR main unit and S-AIR sub unit closer to each other. • Avoid use of equipment that generates electromagnetic energy, such as a microwave oven. • Place the S-AIR main unit and S-AIR sub unit separately from other wireless devices. • Avoid using any other wireless devices. • Change the “RF CHNG” setting (page 57). • Change the S-AIR ID settings of the S-AIR main unit and S-AIR sub unit. AM Ground wire (not supplied) To ground continued 67GB Radio stations cannot be tuned in. • Check that the antennas are connected securely. Adjust the antennas and connect an external antenna, if necessary. • The signal strength of the stations is too weak (when tuning in with automatic tuning). Change to monaural reception (page 42). • No stations have been preset or the preset stations have been cleared (when tuning by scanning preset stations). Preset the stations (page 42). RDS does not work.a) • Make sure that you are tuned to an FM RDS station. • Select a stronger FM station. The RDS information that you want does not appear.a) • Contact the radio station and find out whether they actually provide the service in question. If so, the service may be temporarily out of order. a) Models of area code CEL, CEK only. Remote control The remote does not function. • For receiver operation, you can only use the DISPLAY button when the TUNER input is selected. • Point the remote at the remote sensor on the receiver. • Remove any obstacles in the path between the remote and the receiver. • Replace all the batteries in the remote with new ones, if they are weak. • Make sure you select the correct input on the remote. 68GB Others The ACTIVE STANDBY lamp is flashing. • The receiver is in protection mode. Turn off the receiver and turn it on again. Error messages If an error message appears while you perform Auto Calibration, see “When error codes appear” (page 25) to solve the problem. If you are unable to remedy the problem using the troubleshooting guide Clearing the receiver’s memory may remedy the problem (page 22). However, note that all memorized settings will be reset to their factory settings and you will have to readjust all settings on the receiver. If the problem persist Consult your nearest Sony dealer. Note that if service personnel changes some parts during repair, these parts may be retained. In the event of a problem with S-AIR function, have a Sony dealer check the entire system together (S-AIR main unit and S-AIR sub unit). Reference sections for clearing the receiver’s memory To clear See All memorized settings page 22 Inputs Specifications Amplifier section Models of area code CEL, CEK, AU, TW Power Output1) Stereo mode (rated) 108 W + 108 W (3 ohms at 1 kHz, THD 1%) Surround mode (reference) RMS Output (3 ohms at 1 kHz, THD 10%) FRONT2): 143 W/ch CENTER2): 143 W SUR2): 143 W/ch (1.5 ohms at 70 Hz, THD 10%) SUBWOOFER2): 285 W 1) Measured under the following conditions: Area code FM tuner section Tuning range 87.5 – 108.0 MHz Antenna FM wire antenna Antenna terminals 75 ohms, unbalanced Intermediate frequency 10.7 MHz AM tuner section Tuning range Area code Tuning scale 10 kHz step 9 kHz step AU 530 – 1,710 kHz 531 – 1,710 kHz TW, TH, SP 530 – 1,610 kHz 531 – 1,602 kHz CEL, CEK – 531 – 1,602 kHz Antenna Loop antenna Intermediate frequency 450 kHz General Power requirements Area code Power requirements CEL, CEK, SP 220 – 240 V AC, 50/60 Hz AU 240 V AC, 50 Hz TW 110 V AC, 60 Hz TH 220 V AC, 50/60 Hz Power requirements CEL, CEK 230 V AC, 50 Hz AU, SP 240 V AC, 50 Hz TW 110 V AC, 60 Hz TH 220 V AC, 50 Hz 2) Reference power output for front, center, surround speakers and subwoofer. Depending on the sound field settings and the source, there may be no sound output. Power output (DIGITAL MEDIA PORT) DC OUT: 5 V, 700 mA MAX Power consumption Area code Power consumption CEL, CEK, AU, TW 165 W TH, SP 140 W continued 69GB Additional Information Models of area code SP, TH Power Output1) Stereo mode (rated) 90 W + 90 W (3 ohms at 1 kHz, THD 1%) Surround mode (reference) RMS Output (3 ohms at 1 kHz, THD 10%) FRONT2): 125 W/ch CENTER2): 125 W SUR2): 125 W/ch (1.5 ohms at 80 Hz, THD 10%) SUBWOOFER2): 210 W Analog Sensitivity: 1 V/50 kohms Digital (Coaxial) Impedance: 75 ohms Tone Gain levels ±10 dB, 0.5 dB step Reproduction frequency range: 28 – 20,000 Hz Power consumption (during standby mode) 0.3 W (When Control for HDMI and S-AIR standby are off) Dimensions (w/h/d) (Approx.) 430 × 66.5 × 333 mm including projecting parts and controls Mass (Approx.) 3.4 kg Speaker section HT-SF360 only • Front speaker (SS-MSP36F) • Surround speaker (SS-SRP36F) • Center speaker (SS-CNP36) Front/Surround speaker Full range Center speaker Full range, Magnetically shielded Speaker unit Front/Surround speaker 65 mm, cone type Center speaker 30 × 60 mm, cone type Enclosure type Front/Surround speaker Bass reflex Center speaker Acoustic suspension Rated Impedance 3 ohms Dimension (w/h/d) (Approx.) Front speaker 113 × 830 × 83 mm (without stand) 315 × 1,015 – 1,345 × 315 mm (with stand) Surround speaker 108 × 540 × 78 mm (without stand) 290 × 1,045 – 1,235 × 290 mm (with stand) Center speaker 380 × 50 × 64 mm (with foot) Mass (Approx.) Front speaker 1.6 kg (without stand) 3.3 kg (with stand) Surround speaker 1.1 kg (without stand) 2.6 kg (with stand) Center speaker 0.38 kg 70GB • Subwoofer (SS-WP36) Speaker unit 160 mm, cone type Enclosure type Bass reflex Rated Impedance 1.5 ohms Dimensions (w/h/d) (Approx.) 220 × 395 × 325 mm (with foot) Mass (Approx.) 5.6 kg HT-SS360 only • Front speaker (SS-MSP36S) • Surround speaker (SS-SRP36S) • Center speaker (SS-CNP36) Front/Surround speaker Full range Center speaker Full range, Magnetically shielded Speaker unit Front/Surround speaker 65 mm, cone type Center speaker 30 × 60 mm, cone type Enclosure type Front/Surround speaker Bass reflex Center speaker Acoustic suspension Rated Impedance 3 ohms Dimension (w/h/d) (Approx.) Front/Surround speaker 102 × 163 × 77 mm (with foot) Center speaker 380 × 50 × 64 mm (with foot) Mass (Approx.) Front speaker 0.52 kg Surround speaker 0.48 kg Center speaker 0.38 kg • Subwoofer (SS-WP36) Speaker unit 160 mm, cone type Enclosure type Bass reflex Rated Impedance 1.5 ohms Dimensions (w/h/d) (Approx.) 220 × 395 × 325 mm (with foot) Mass (Approx.) 5.6 kg Supplied speakers Front speaker (2) Center speaker (1) Surround speaker (2) Subwoofer (1) Supplied accessories Operating Instructions (this manual) Quick Setup Guide (1) Speaker Stand Installation Guide (HT-SF360 only) (1) FM wire antenna (1) AM loop antenna (1) Remote commander • RM-AAU058 (1) R6 (size-AA) batteries (2) Optimizer microphone (ECM-AC2) (1) Speaker cords (5) Foot pads • Speakers – HT-SS360 only (20) – HT-SF360 only (4) • Subwoofer (4) Screws (small) (HT-SF360 only) (12) Screws (large) (HT-SF360 only) (8) For details on the area code of the component you are using, see page 4. Design and specifications are subject to change without notice. Additional Information Halogenated flame retardants are not used in the certain printed wiring boards. 71GB Index A H S AUTO CALIBRATION 23 HDMI connecting 19 Control for HDMI 35 S-AIR 52 Satellite tuner/Set-top box connecting 19 enjoying 29 Selecting component 28 Sleep Timer 51 Speakers connecting 15 Super Audio CD player connecting 18 playback 30 System Audio Control 47 System Power Off 48 B Blu-ray disc player connecting 19 playback 30 C CD player connecting 18 playback 30 Control for HDMI connecting 19 preparing 45 D Digital Cinema Sound (DCS) 40, 61 DIMMER 50 DISPLAY 50 Dolby Digital 61 DTS 62 DVD player connecting 20 playback 30 DVD recorder connecting 20 E I IN MODE 51 Initial setup 22 M Menu A.CAL 35 CUSTOM 38 LEVEL 37 S-AIR 39 SET HDMI 35 SP SETUP 36 TONE 37 Muting 28 O One-Touch Play 47 P PAIRING 54 Power Save 49 R RDS 44 Remote commander 9 Error messages 68 (3) Sony Corporation Printed in Malaysia T TEST TONE 27 Tuner connecting 21 Tuning automatically 41 to preset stations 43 TV connecting 16 enjoying 29 V VCR connecting 20 playback 30 Volume Limit 48
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement