Subfloor Condition and Preparation

Subfloor Condition and Preparation
USER GUIDE TB-9054
Conductive Epoxy Adhesive
Application Instructions & Safety Data Sheets
Made in the
United States of America
Subfloor Condition and Preparation
The adhesive is designed for tile installations above-,
on- or below-grade, and where moisture is not a factor.
The subfloor must be level, clean, dry, and free of
contaminants like powdery residue, concrete curing
compound, or old adhesive. For optimum adhesion, the
surface of the subfloor should be abraded to a texture
similar to that of 80- to 100-grit sandpaper. Protrusions
should be removed; cracks and depressions should be
filled with good grade cementatious underlayment, and
uneven areas should be leveled.
Temperature and Preconditioning
Figure 1. 8403 Conductive Epoxy Adhesive
Description
SCS’s 8403 adhesive is a conductive, high-solids,
2-part epoxy adhesive that is recommended for
installation of 8400 Series Static Control Vinyl Floor
Tile, both conductive and static-dissipative tiles. It
provides an efficient electrical groundplane underneath
the entire floor to drain electrostatic charges to ground.
The black adhesive is supplied in “gallon units”, each
consisting of two gallon-sized cans, Part A and Part
B, that are pre-measured to provide the proper mix
ratio when the contents of the two cans are combined.
The coverage rate for each gallon unit is typically 135
square feet.
Both the floor tile and the conductive adhesive should
be preconditioned to the job site environment for 48
hours prior to installation. Recommended storage,
conditioning, and installation temperature range is 65°F
to 85°F.
Mixing
Part A
Part B
Mixed
Material
Epoxy
Curative
--
Color
Translucent
Black
Black
Weight/
Gallon
9.2 lb/gal
8.3 lb/gal
8.9 lb/gal
The mixing ratio, Part A to Part B, is unequal parts by
volume. All of the conductive pigment is contained
in Part B. Each part should be thoroughly mixed
individually in its own can before the two parts are
combined. (Two wooden mixing paddles are provided
in each carton; use a separate paddle to stir each
part.) Pour the entire premixed contents of the Part A
into the can holding the premixed Part B and mix the
two parts together for 3 to 5 minutes. NOTE: Thorough
mixing is extremely important to attain the specified
electrical properties and complete chemical cure. A
variable-speed electric drill (3/8”) with a mixing paddle
should be used to mix Parts A and B together in the
Part B can. Mixing speed should not exceed 200 rpm;
higher speeds will create excessive heat, speeding
up the curing action of the epoxy in the can, making it
thicker and more difficult to spread.
Specific
Gravity
1.1
0.99
1.05
Spreading
Flash Point 93°F
54°F
93°F
Weight/
Gallon
93%
86%
89%
VOC
79 g/l
150 g/l
115 g/l
Electrical
-Resistance
After Curing
--
< 3.0 x 106
Shelf Life
1 year
--
Technical Data
1 year
Immediately after mixing, pour the entire contents of
the can onto the floor. If the mixed compound is left
in the can, it will generate excessive heat and start
to cure prematurely, making it unusable. Spread
the adhesive as soon as possible using a 1/16"
square-notched trowel (2 mm x 2 mm) with 1/16" (2
mm) flats, held at a 45° angle to the floor surface.
SCS - 926 JR Industrial Drive, Sanford, NC 27332 • (919) 718-0000 • Website: StaticControl.com
TB-9054 Page 1 of 12 April 2016
© 2016 DESCO INDUSTRIES INC.
Employee Owned
Spread Rate
Typical spread rate for 8403 conductive adhesive,
using the recommended trowel, is approximately
135 square feet per unit. Actual spread rate varies
with subfloor porosity and applicator technique, and
the installer should adjust according to conditions.
Snapping chalk lines on the floor to outline sections
135 square feet in area will make the spread rate
control easier.
Tile Installation
After the adhesive has been spread, allow it to “flash
off” for a short time (typically 15 to 20 minutes) before
starting to install tile. The working life of the spread
adhesive is about one hour. These times will vary
with temperature, and the installer should adjust
according to conditions. “Drop” each tile into place
and press firmly into the adhesive; do not “slide” the
tile into position. NOTE: Throughout the installation,
the installer should periodically lift a tile to ensure
that there is adequate adhesive transfer. The back
of each tile should be at least 90% covered with
adhesive. Work from the “dry” side to avoid contact
with the freshly laid tiles; if working on top of the tiles is
necessary, use a kneeling board to avoid accidentally
shifting any tiles. Shortly after each section has been
laid, it must be rolled twice with a 150-lb (70 kilogram)
sectioned roller, first in one direction and then in a
perpendicular direction. Roll the entire floor once again
at completion. Use a hand roller in areas that cannot
be reached with a large roller.
RoHS 2, REACH, and Conflict Minerals Statement
None of the RoHS 2 restricted materials or REACH
substances of very high concern as of 2014/12/17,
or Conflict Minerals are intentionally added in
manufacturing this product. Ref: European Union
Directive 2011/65/EU and Regulation (EC) No.
1907/2006/CE. See SCS Limited Warranty at
StaticControl.com.
Limited Warranty, Warranty Exclusions, Limit of
Liability and RMA Request Instructions
See SCS Warranty
http://www.StaticControl.com/Warranty.aspx
Clean Up
Clean excess adhesive on the tile and tools promptly
using a soapy solution or denatured ethyl alcohol or
isopropyl alcohol (friction alcohol).
Cure Time
Typically, newly installed tile can withstand foot traffic
24 hours after installation. Allow a full 48 hours for
curing before moving any equipment onto the new
floor.
Grounding
SCS recommends installing one
copper grounding strip per
1,000 square feet throughout
the installation. A thin coating of
adhesive should be applied on
top of grounding strip to ensure
good contact with tile backing.
SCS - 926 JR Industrial Drive, Sanford, NC 27332 • (919) 718-0000 • Website: StaticControl.com
TB-9054 Page 2 of 12
© 2016 DESCO INDUSTRIES INC.
Employee Owned
Safety Data Sheet
NFPA Designation 704
May be used to comply with ANSI Z400.1-2004, 29 CFR
1910.1200, Regulation (EC) No 1272/2008 (CLP Regulation)
and GHS. Standards must be consulted for specific
requirements.
Degree of Hazard
4 = Extreme
3 = High
2 = Moderate
Health
(Blue)
3
2
1 = Slight
0 = Insignificant
Special Hazard
Flammability
(Red)
0
Instability
(Yellow)
HMIS RATING: Health 2, Flammability 3, Physical Hazard 0, Personal Protection B
SECTION 1 — CHEMICAL PRODUCT AND COMPANY IDENTIFICATION
Product Name/Identity:
SCS 8403 Conductive Epoxy Adhesive, Part A
Chemical Name:
Epoxy Resin
Manufacturer:Milamar Coatings, Inc.
Address:
311 NW 122nd Street, Suite 100
Oklahoma City, OK 73114
Telephone:405-755-8448
Emergency Number:
800-255-3924 or 813-248-0585 (International)
SECTION 2 — HAZARDS IDENTIFICATION
Classification:
Flammable liquid
Category 3
Eye irritation
Category 2A-2B
Labelling:
Flame, Exclamation mark.
Warning.
Flammable liquid and Eye irritation.
Symbol:
Signal word:
Hazard statement:
Precautionary statements:
IF SWALLOWED: Immediately call your doctor or physician. Do NOT
induce vomiting.
Do not eat, drink or use with open flame.
Wash hands thoroughly after handling.
Keep container tightly closed.
Keep away from heat/sparks/open flame.
Store in cool ventilated place.
SECTION 3 — COMPOSITION/INFORMATION ON INGREDIENTS
Mixtures
Chemical Identity
CAS No.
Concentration
Reaction products of epichlorohydrin and bisphenol A
25085-99-8
70-80%
Epoxy resin
28064-14-4
10-15%
Amorphous silica
112945-54-5
<5%
Ethanol
64-17-5
<10%
SECTION 4 — FIRST AID MEASURES
Description of necessary first-aid measures:
Remove contact lenses at once. Immediately flush eyes with large amounts of Eye Contact: water or normal saline for at least 30 minutes. Hold eyelids apart while flushing to
rinse entire surface of eye and lids with water.
Skin Contact: Immediately flush skin with plenty of water for at least 15 minutes while removing
contaminated clothing and shoes. Call a Physician if irritation persists. Wash
clothing before reuse. Contaminated Leather Articles, including shoes, cannot be
econtaminated and should be destroyed to prevent reuse.
SCS - 926 JR Industrial Drive, Sanford, NC 27332 • (919) 718-0000 • Website: StaticControl.com
TB-9054 Page 3 of 12
© 2016 DESCO INDUSTRIES INC.
Employee Owned
Inhalation: Remove victim to fresh air if effects occur. If not breathing, give artificial
respiration. Get immediate medical attention.
Ingestion: Do not induce vomiting. If patient is conscious and can swallow, give two
glasses of water (16oz.). Get immediate medical attention. Never give anything by mouth to an unconscious or convulsing person.
Most Important symptoms/effects, acute and delayed:
Signs and Symptoms: Irritation as noted above. Skin sensitization (allergy) may be evidenced by
rashes, especially hives.
Aggravated medical conditions:
Pre-existing skin and eye disorders may be aggravated by exposure to this
product. Preexisting skin and lung allergies may increase the chance of
developing increased allergy symptoms from exposure to this product.
Other Health Effects: Based on animal studies, repeated exposure to components of this
product may cause damage to liver, kidney, and respiratory systems.
Reports have associated repeated and prolonged occupational exposure
to solvents with permanent brain and nervous system damage. Intentional
misuse by deliberately concentrating and inhaling vapors may be harmful
or fatal.
Indication of immediate medical attention and special treatment needed, if necessary:
Contact a poison control center for additional treatment information. As a
precaution, exposure to liquids, vapors, mists, or fumes should be
minimized.
SECTION 5 — FIREFIGHTING MEASURES
Suitable extinguishing media:
Use alcohol type foam, dry chemical, or CO2.
Specific hazards arising from the chemical:
Flash Point is 93°F TCC. None Known.
Special protective actions for fire-fighters: Use water spray to cool fire Exposed surfaces and to protect personnel. If
a leak or spill has not ignited, use ER spray to disperse the vapors.
Contain the runoff stream. Try to cover liquid pills with foam. Do not enter
confined fire space without full bunker gear (helmet with face shield,
bunker coats, gloves, and rubber boots), including a positive pressure
IOSH approved self contained breathing apparatus.
SECTION 6 — ACCIDENTAL RELEASE MEASURES
Personal precautions,
protective equipment and
emergency procedures:
Methods and materials for
containment and clean up:
Ventilate the area. Avoid breathing vapor. Use self-contained breathing
apparatus or supplied air for large spills or confined areas.
Contain spill if possible. Wipe up or absorb on suitable material and pick
up with shovels. Do not use sawdust, wood chips, or other cellulosic
materials to absorb the spill. Prevent entry into sewers and waterways.
Dispose of in accordance with federal, state, and local regulations.
SECTION 7 — HANDLING AND STORAGE
Precautions for safe handling:
Ground all transfer equipment. Take precautionary measures against static
discharge. Handle as an industrial chemical.
Conditions for safe storage,
including any incompatibilities:
Ground all transfer equipment. Take precautionary measures against
static discharge. Handle as an industrial chemical. Keep container tightly
closed when not in use. Practice good caution and personal cleanliness
to avoid skin and eye contact. Hold bulk storage under nitrogen blanket.
Store in a cool, dry place with adequate ventilation. Keep away from open
flames and high temperatures.
SCS - 926 JR Industrial Drive, Sanford, NC 27332 • (919) 718-0000 • Website: StaticControl.com
TB-9054 Page 4 of 12
© 2016 DESCO INDUSTRIES INC.
Employee Owned
SECTION 8 — EXPOSURE CONTROLS/PERSONAL PROTECTION
Control parameters
Component
CAS No.
Percent
Exposure Limits
Reaction products of epichlorohydrin and
bisphenol A
25085-99-8
70-80%
None established
Source
Epoxy resin
28064-14-4
10-15%
None established
Amorphous silica
112945-54-5
<5%
5 mg/m3 TWA, Respirable
OSHA
Ethanol
64-17-5
<10%
1000 ppm TWA
OSHA
N/A
Appropriate engineering controls: Individual protection measures, such as personal protective equipment:
Provide adequate ventilation. Avoid breathing of vapors or mists. Airborne
Respiratory Protection: concentrations should be kept to lowest levels possible. When exposures
are not adequately controlled, use an approved respirator. Selection of
air-purifying or positive-pressure supplied air will depend on the specific
operation and the potential airborne concentration of material. For
emergency conditions, use an approved positive-pressure self-contained
breathing apparatus.
Protective clothing such as uniforms, coveralls, or lab coats must be
Protective Clothing: worn. Launder or dryclean when soiled. Gloves and goggles resistant
to chemicals and petroleum distillates required. When handling large
quantities, impervious suits, gloves, and rubber boots must be worn.
SECTION 9 — PHYSICAL AND CHEMICAL PROPERTIES
Appearance (physical state, color, etc.):Clear/White Paste
Odor: Little to No Odor
Odor threshold: N/A
pH: N/A
Melting point/freezing point: N/A
Initial boiling point and boiling range: Not Determined
Flash Point: 93°F TCC
Not Determined
Evaporation rate: Flammability (solid, gas): N/A
Upper/lower flammability or explosive N/A
limits:
Vapor pressure: Not Determined
Vapor Density: Not Determined
Relative density (specific gravity): 1.148
Solubility(ies): Not Soluble (Water)
Partition coefficient; n-octanol/water: N/A
Auto-ignition temperature: N/A
Decomposition temperature: N/A
Viscosity:N/A
SECTION 10 — STABILITY AND REACTIVITY
Reactivity: N/A
Chemical stability: Excess heating over long periods of time degrades the resin.
Possibility of hazardous reactions: Will not occur by itself, but masses of more than 1 pound of product plus
an aliphatic amine will cause irreversible polymerization with considerable
heat buildup.
Conditions to avoid: Avoid exposure to heat, light, flame, or other sources of ignition. Can
react vigorously with strong oxidizing agents, strong lewis or mineral
acids, and strong mineral and organic base/especially primary and
secondary amines. Reaction with some curing agent may produce
considerable heat.
SCS - 926 JR Industrial Drive, Sanford, NC 27332 • (919) 718-0000 • Website: StaticControl.com
TB-9054 Page 5 of 12
© 2016 DESCO INDUSTRIES INC.
Employee Owned
Incompatible materials: N/A
Hazardous decomposition products: Hazardous combustion products may include intense heat, dense black
smoke, carbon monoxide, carbon dioxide, as well as organic compounds
of unknown structure.
SECTION 11 — TOXICOLOGICAL INFORMATION
Likely routes of exposure: N/A
Symptoms related to the physical, chemical and toxicological characteristics:
Eye Contact: Irritating and will injure eye tissue if not removed promptly.
Skin Contact: May cause irritation. Has been known to cause allergic skin reaction in
humans. Prolonged contact may cause blisters.
Inhalation: High vapor concentrations are irritating to the eyes and respiratory tract,
may cause headaches and dizziness.
Ingestion: Oral toxicity is considered to be extremely low.
Delayed and immediate effects and N/A
also chronic effects from short and
long term exposure:
Numerical measures of toxicity:
Ingredient Name
CAS No.
Percent
Acute Oral LD50
Acute Oral LD50
Acute Inhalation
LC50
Reaction products of
epichlorohydrin and
bisphenol A
25085-99-8
70-80%
>5.0 g/kg (rat)
>6.0 g/kg (rat)
Not available
Epoxy resin
28064-14-4
10-15%
>5.0 g/kg (rat)
>3.0 g/kg (rat)
>1.7 mg/L (rat)
Amorphous silica
112945-54-5
<5%
>5000 mg/kg (rat)
No data
No data
Ethanol
64-17-5
<10%
Not available
Not available
Not available
SECTION 12 — ECOLOGICAL INFORMATION
Ecotoxicity: N/A
N/A
Persistence and degradability: Bioaccumulative potential: N/A
Mobility in soil: N/A
Other adverse effects: N/A
SECTION 13 — DISPOSAL CONSIDERATIONS
Disposal methods: Dispose of in accordance with federal, state, and local regulations.
SECTION 14 — TRANSPORT INFORMATION
UN number: UN proper shipping name: Transport hazard class(es): Packing group, if applicable: Environmental hazards: Transport in bulk: Special precautions for user: UN 1866
UN 1866, Resin Solution, Flammable, 3, PG III
3
III
N/A
N/A
N/A
SCS - 926 JR Industrial Drive, Sanford, NC 27332 • (919) 718-0000 • Website: StaticControl.com
TB-9054 Page 6 of 12
© 2016 DESCO INDUSTRIES INC.
Employee Owned
SECTION 15 — REGULATORY INFORMATION
DSL/NDSL:
These items are specified in the public Portion of the Domestic
Substances List: CAS Number 28064-14-4 with Maximum Weight 15%.
CAS Number 64-17-5 with Maximum Weight 10%.
TSCA:
These items are listed on the U.S. Toxic Substance
Control Act: CAS Number 64-17-5 with Maximum Weight 10%.
DSL/NDSL: These items are specified in the public Portion of the Domestic
Substances List: CAS Number 25085-99-8 with Maximum Weight 80%
CAS Number 28064-14-4 with Maximum Weight 15%. CAS Number
64-17-5 with Maximum Weight 10%.
REACH SVHC: No items in this product are on REACH’s list of Substances of Very High
Concern.
EINECS: All components are included in the EINECS inventories.
SARA Title III: This product is not subject to the reporting requirements of SARA Title
III Section 313.
SECTION 16 — OTHER INFORMATION
HMIS RATING: Health 2, Flammability 3, Physical Hazard 0, Personal Protection B
NFPA RATING: Special Hazard: N/A, Health: 2, Flammability: 3, Instability: 0
SDS Updated: 2016-03-29
Disclaimer
OTHER INFORMATION: This information relates only to the specific material designated and may not be valid
for such material used in combination with any other materials or in any other process. Such information is to
the best of the company’s knowledge and believed accurate and reliable as of the date indicated. However,
no representation, warranty or guarantee of any kind, express or implied, is made as to its accuracy, reliability
or completeness and we assume no responsibility for any loss, damage or expense, direct or consequential,
arising out of use. It is the user’s responsibility to satisfy himself as to the suitableness and completeness of such
information for his own particular use.
SCS - 926 JR Industrial Drive, Sanford, NC 27332 • (919) 718-0000 • Website: StaticControl.com
TB-9054 Page 7 of 12
© 2016 DESCO INDUSTRIES INC.
Employee Owned
Safety Data Sheet
NFPA Designation 704
May be used to comply with ANSI Z400.1-2004, 29 CFR
1910.1200, Regulation (EC) No 1272/2008 (CLP Regulation)
and GHS. Standards must be consulted for specific
requirements.
Degree of Hazard
4 = Extreme
3 = High
2 = Moderate
Health
(Blue)
3
2
1 = Slight
0 = Insignificant
Special Hazard
Flammability
(Red)
0
Instability
(Yellow)
HMIS RATING: Health 2, Flammability 3, Physical Hazard 0, Personal Protection B
SECTION 1 — CHEMICAL PRODUCT AND COMPANY IDENTIFICATION
Product Name/Identity:
SCS 8403 Conductive Epoxy Adhesive, Part B
Chemical Name:
Polyamine Hardener
Manufacturer:Milamar Coatings, Inc.
Address:
311 NW 122nd Street, Suite 100
Oklahoma City, OK 73114
Telephone:405-755-8448
Emergency Number:
800-255-3924 or 813-248-0585 (International)
SECTION 2 — HAZARDS IDENTIFICATION
Classification:
Flammable liquid
Category 3
Eye irritation
Category 2A-2B
Labelling:
Flame, Exclamation mark.
Warning.
Flammable liquid and Eye irritation.
Symbol:
Signal word:
Hazard statement:
Precautionary statements:
IF SWALLOWED: Immediately call your doctor or physician. Do NOT
induce vomiting.
Do not eat, drink or use with open flame.
Wash hands thoroughly after handling.
Keep container tightly closed.
Keep away from heat/sparks/open flame.
Store in cool ventilated place.
SECTION 3 — COMPOSITION/INFORMATION ON INGREDIENTS
Mixtures
Chemical Identity
CAS No.
Concentration
Polyamine Adduct
Proprietary
60-70%
Methanol
67-56-1
10%
Ethanol
64-17-5
<10%
Carbon Black
1333-86-4
10-15%
SECTION 4 — FIRST AID MEASURES
Description of necessary first-aid measures:
Remove contact lenses at once. Immediately flush eyes with large amounts of Eye Contact: water or normal saline for at least 30 minutes. Hold eyelids apart while flushing to
rinse entire surface of eye and lids with water.
Skin Contact: Immediately flush skin with plenty of water for at least 15 minutes while removing
contaminated clothing and shoes. Call a Physician if irritation persists. Wash
clothing before reuse. Contaminated Leather Articles, including shoes, cannot be
econtaminated and should be destroyed to prevent reuse.
SCS - 926 JR Industrial Drive, Sanford, NC 27332 • (919) 718-0000 • Website: StaticControl.com
TB-9054 Page 8 of 12
© 2016 DESCO INDUSTRIES INC.
Employee Owned
Inhalation: Remove victim to fresh air if effects occur. If not breathing, give artificial
respiration. Get immediate medical attention.
Ingestion: Do not induce vomiting. If patient is conscious and can swallow, give two
glasses of water (16oz.). Get immediate medical attention. Never give anything by mouth to an unconscious or convulsing person.
Most Important symptoms/effects, acute and delayed:
Signs and Symptoms: Irritation as noted above. Skin sensitization (allergy) may be evidenced by rashes, especially hives.
Aggravated medical conditions:
Pre-existing skin and eye disorders may be aggravated by exposure to this
product. Preexisting skin and lung allergies may increase the chance of
developing increased allergy symptoms from exposure to this product.
Other Health Effects: Based on animal studies, repeated exposure to components of this product
may cause damage to liver, kidney, and respiratory systems. Reports have
associated repeated and prolonged occupational exposure to solvents with
permanent brain and nervous system damage. Intentional misuse by
deliberately concentrating and inhaling vapors may be harmful or fatal.
Indication of immediate medical attention and special treatment needed,
if necessary:
Contact a poison control center for additional treatment information. As a
precaution, exposure to liquids, vapors, mists, or fumes should be
minimized.
SECTION 5 — FIREFIGHTING MEASURES
Suitable extinguishing media:
Use alcohol type foam, dry chemical, or CO2.
Specific hazards arising from the chemical:
Flash Point is 93°F TCC. None Known.
Special protective actions for fire-fighters: Use water spray to cool fire Exposed surfaces and to protect personnel. If
a leak or spill has not ignited, use ER spray to disperse the vapors. Contain the runoff stream. Try to cover liquid pills with foam. Do not enter
confined fire space without full bunker gear (helmet with face shield,
bunker coats, gloves, and rubber boots), including a positive pressure
IOSH approved self contained breathing apparatus.
SECTION 6 — ACCIDENTAL RELEASE MEASURES
Personal precautions, protective Ventilate the area. Avoid breathing vapor. Use self-contained breathing
equipment and emergency procedures: apparatus or supplied air for large spills or confined areas.
Methods and materials for containment Contain spill if possible. Wipe up or absorb on suitable material and pick
and clean up:
up with shovels. Do not use sawdust, wood chips, or other cellulosic
materials to absorb the spill. Prevent entry into sewers and waterways.
Dispose of in accordance with federal, state, and local regulations.
SECTION 7 — HANDLING AND STORAGE
Precautions for safe handling: Ground all transfer equipment. Take precautionary measures against static
discharge. Handle as an industrial chemical.
Conditions for safe storage, including
any incompatibilities:
Ground all transfer equipment. Take precautionary measures against
static discharge. Handle as an industrial chemical. Keep container tightly
closed when not in use. Practice good caution and personal cleanliness to
avoid skin and eye contact. Hold bulk storage under nitrogen
blanket. Store in a cool, dry place with adequate ventilation. Keep away
from open flames and high temperatures.
SCS - 926 JR Industrial Drive, Sanford, NC 27332 • (919) 718-0000 • Website: StaticControl.com
TB-9054 Page 9 of 12
© 2016 DESCO INDUSTRIES INC.
Employee Owned
SECTION 8 — EXPOSURE CONTROLS/PERSONAL PROTECTION
Control parameters
Component
CAS No.
Percent
Exposure Limits
Polyamine Adduct
Proprietary
60-70%
None established
Methanol
67-56-1
<10%
200 ppm (TWA)
OSHA
OSHA
Ethanol
64-17-5
<10%
1000 ppm (TWA)
Carbon Black
1333-86-4
10-15%
None established
Source
N/A
Appropriate engineering controls: Individual protection measures, such as personal protective equipment:
Provide adequate ventilation. Avoid breathing of vapors or mists. Airborne
Respiratory Protection: concentrations should be kept to lowest levels possible. When exposures
are not adequately controlled, use an approved respirator. Selection of
air-purifying or positive-pressure supplied air will depend on the specific
operation and the potential airborne concentration of material. For
emergency conditions, use an approved positive-pressure self-contained
breathing apparatus.
Protective Clothing: Protective clothing such as uniforms, coveralls, or lab coats must be
worn. Launder or dryclean when soiled. Gloves and goggles resistant
to chemicals and petroleum distillates required. When handling large
quantities, impervious suits, gloves, and rubber boots must be worn.
SECTION 9 — PHYSICAL AND CHEMICAL PROPERTIES
Appearance (physical state, color, etc.):Black Paste
Odor: Amine
Odor threshold: N/A
pH: N/A
Melting point/freezing point: N/A
Initial boiling point and boiling range: Not Determined
Flash Point: 54°F TCC
Not Determined
Evaporation rate: Flammability (solid, gas): N/A
Upper/lower flammability or explosive N/A
limits:
Vapor pressure: Not Determined
Vapor Density: Not Determined
Relative density (specific gravity): 0.99
Solubility(ies): Not Soluble (Water)
Partition coefficient; n-octanol/water: N/A
Auto-ignition temperature: N/A
Decomposition temperature: N/A
Viscosity:N/A
SECTION 10 — STABILITY AND REACTIVITY
Reactivity: N/A
Chemical stability: Excess heating over long periods of time degrades the resin.
Possibility of hazardous reactions: Will not occur by itself.
Conditions to avoid: Avoid exposure to heat, light, flame, or other sources of ignition. Can react
vigorously with strong oxidizing agents.
Incompatible materials: N/A
Hazardous decomposition products: Hazardous combustion products may include intense heat, dense black
smoke, carbon monoxide, carbon dioxide, as well as organic compounds
of unknown structure.
SCS - 926 JR Industrial Drive, Sanford, NC 27332 • (919) 718-0000 • Website: StaticControl.com
TB-9054 Page 10 of 12
© 2016 DESCO INDUSTRIES INC.
Employee Owned
SECTION 11 — TOXICOLOGICAL INFORMATION
Likely routes of exposure: N/A
Symptoms related to the physical, chemical and toxicological characteristics:
Eye Contact: Irritating and will injure eye tissue if not removed promptly.
Skin Contact: May cause irritation. Has been known to cause allergic skin reaction in
humans. Prolonged contact may cause blisters.
Inhalation: High vapor concentrations are irritating to the eyes and respiratory tract,
may cause headaches and dizziness.
Ingestion: Oral toxicity is considered to be extremely low.
Delayed and immediate effects and N/A
also chronic effects from short and
long term exposure:
Numerical measures of toxicity:
Ingredient Name
CAS No.
Percent
Acute Oral LD50
Acute Oral LD50
Acute Inhalation
LC50
Polyamine Adduct
Proprietary
60-70%
<=2.0 g/kg (rat)
<=2.0 g/kg
<=5.0 mg/L
Methanol
67-56-1
<10%
2000 mg/kg
(rabbit)
Not available
Not available
Ethanol
64-17-5
<10%
Not available
Not available
Not available
Carbon Black
1333-86-4
10-15%
>8.0 g/kg (rat)
Not available
Not available
SECTION 12 — ECOLOGICAL INFORMATION
Ecotoxicity: N/A
N/A
Persistence and degradability: Bioaccumulative potential: N/A
Mobility in soil: N/A
Other adverse effects: N/A
SECTION 13 — DISPOSAL CONSIDERATIONS
Disposal methods: Dispose of in accordance with federal, state, and local regulations.
SECTION 14 — TRANSPORT INFORMATION
UN number: UN2924
UN 2924, Flammable Liquid, Corrosive, nos, 3(8), PG II, (methanol and
UN proper shipping name: polyamines)
3(8)
Transport hazard class(es): Packing group, if applicable: II
Environmental hazards: N/A
Transport in bulk: N/A
Special precautions for user: N/A
SECTION 15 — REGULATORY INFORMATION
These items are listed and subjected to the reporting requirements of the
SARA Title III: SARA Title III Section 313 Inventory of the Emergency Planning and
Community Right-To-Know Act of 1986 and of 40 CFR37: CAS Number
67-56-1 with Maximum Weight 10%
California proposition 65:
These items are listed in the California Safe Drinking Water and Toxic
Enforcement Act: CAS Number 67-56-1 with Maximum Weight 10%.
CAS Number 1333-86-4 with Maximum Weight 15%.
These items are listed on the U.S. Toxic Substance Control Act: CAS
TSCA:
Number 67-56-1 with Maximum Weight 10%. CAS Number 64-17-5 with
Maximum Weight 20%. CAS Number 1333-86-4 with Maximum Weight
15%.
SCS - 926 JR Industrial Drive, Sanford, NC 27332 • (919) 718-0000 • Website: StaticControl.com
TB-9054 Page 11 of 12
© 2016 DESCO INDUSTRIES INC.
Employee Owned
DSL/NDSL: These items are specified in the public Portion of the Domestic
Substances List: CAS Number 67-56-1 with Maximum Weight 10%.
CAS Number 64-17-5 with Maximum Weight 10%. CAS Number
1333-86-4 with Maximum Weight 15%.
REACH SVHC: No items in this product are on REACH’s list of Substances of Very High
Concern.
EINECS: All components are included in the EINECS inventories.
SECTION 16 — OTHER INFORMATION
HMIS RATING: Health 2, Flammability 3, Physical Hazard 0, Personal Protection B
NFPA RATING: Special Hazard: N/A, Health: 2, Flammability: 3, Instability: 0
SDS Updated: 2016-03-29
Disclaimer
OTHER INFORMATION: This information relates only to the specific material designated and may not be valid
for such material used in combination with any other materials or in any other process. Such information is to
the best of the company’s knowledge and believed accurate and reliable as of the date indicated. However,
no representation, warranty or guarantee of any kind, express or implied, is made as to its accuracy, reliability
or completeness and we assume no responsibility for any loss, damage or expense, direct or consequential,
arising out of use. It is the user’s responsibility to satisfy himself as to the suitableness and completeness of such
information for his own particular use.
SCS - 926 JR Industrial Drive, Sanford, NC 27332 • (919) 718-0000 • Website: StaticControl.com
TB-9054 Page 12 of 12
© 2016 DESCO INDUSTRIES INC.
Employee Owned
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement