Safety-First and MOTORQUICK CIRCUIT-LOCK Manual Motor Controllers and Disconnects

Safety-First and MOTORQUICK CIRCUIT-LOCK Manual Motor Controllers and Disconnects
CIRCUIT-LOCK® and MOTORQUICK®
Manual Motor Controllers and Disconnects
A Safety-First Priority
www.hubbell-wiring.com
®
Wiring Device-Kellems
Hubbell’s Circuit-Lock® Manual Motor Controllers
"Suitable as Motor Disconnects"
Hubbell manufactures one of the most complete lines of motor disconnects on the market. Designed to ensure
maximum reliability and performance, Hubbell Circuit-Lock® motor controllers meet or exceed all industry requirements.
Because our Circuit-Lock® motor controllers are also disconnects, they ensure safety, compliance, flexibility and
productivity for today’s industrial and commercial environments. Whether controlling motor loads, safely terminating
power or isolating equipment, Hubbell has the solution for you—no matter what the environment or application.
Hubbell
Safety
Safety of personnel and
equipment is paramount
in any manufacturing
environment. Hubbell
Circuit-Lock® motor
controllers withstand
short circuits and provide
a high degree of safety
across the factory floor.
Disconnect Switches for
Variable Frequency Drives
(VFDs) safely terminate
power to prevent risk of
injury and damage to highperformance output devices
used for controlling today’s
conveyor systems.
Hubbell
Flexibility
Hubbell
Productivity
With Hubbell’s wide range
of Circuit-Lock® motor
controllers and disconnects
that offer several mounting
options, NEC® line of sight
requirements are easily
achieved at the equipment
or on the wall in virtually
any industrial environment.
Switches with a compact
footprint, a variety of
NEMA® type enclosures
and plug-and-play
LINKOSITY® make switch
placement easier and
more flexible than ever.
Circuit-Lock® keeps assembly
lines, goods and services
moving. By offering a dual
motor controller-disconnect
rating, power can be safely
terminated at any point in the
circuit to perform maintenance
on a single motor without
shutting down the entire
line. With the plug-and-play
LINKOSITY® power system,
MotorQuick® reduces motor
change-out time by more than
65% to get equipment up and
running faster.
Variable Frequency Disconnects
Hubbell
Compliance
Compliance with codes
and regulations is a must in
any industrial environment.
Hubbell motor controllers
meet a variety of
requirements, including
OSHA lockout/tagout,
NSF certification for
hygiene and hazardous
location ratings. Each
Circuit-Lock® motor
controller is UL listed
as “Suitable as Motor
Disconnect”. The NEC®
allows for the disconnect
and controller to be in
one unit.
Each Controller is Also a Disconnect
NEC® is a registered trademark of the National Fire Protection Association (NFPA).
NEMA® is a registered trademark of the National Electrical Manufacturers Association.
2
For complete listing of Hubbell Products see our full line catalog.
www.hubbell-wiring.com
Circuit-Lock® Non-Metallic Disconnect Switches, MotorQuick® and VFDs
Non-metallic disconnect switches control motor loads in wet or
corrosive environments, while MotorQuick® provides faster motor
change-outs and VFD switches reduce equipment damage and
stress on electrical systems.
Fused and Unfused Non-Metallic
Disconnect Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 4
MotorQuick® and VFD Switches . . . . . . . . . . . . . . . . . . . . . Page 5
Stainless Steel, Hazardous Location Disconnects and Mechanical Interlocks
Stainless steel disconnect switched enclosures are ideal for
withstanding harsh environments, while hazardous location
disconnects prevent explosion hazards where flammable gases
and combustible particles are present.
NEMA 4X Stainless Steel Disconnect Switches . . . . . . . . . Page 6
Hazardous Location Disconnects and
Mechanical Interlocks. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 7
IEC and Insulgrip® Pin and Sleeve; Twist-Lock® Mechanical Interlocks
Hubbell’s line of mechanical interlocks provide a horsepower rated
receptacle and a means of disconnect for a variety of portable
equipment, while eliminating the possibility of making lazy
connections or breaking circuits under load.
IEC and Insulgrip® Pin and Sleeve
Mechanical Interlocks. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 8
Watertight Safety-Shroud® Twist-Lock®
Mechanical Interlocks. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 9
600V AC Manual Motor Controllers/Disconnects and Enclosures
Motor loads in industrial environments are easily disconnected with
Hubbell’s complete line of AC manual motor controllers/disconnects,
available in a wide variety of enclosure types including NEMA® 1, 3R
or 4X.
AC Manual Motor Controllers/Disconnects. . . . . . . . . . . . Page 10
Enclosed AC Manual Motor Controllers/Disconnects. . . . . . Page 11
Horsepower Ratings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 12
NEMA® is a registered trademark of the National Electrical Manufacturers Association.
www.hubbell-wiring.com
For complete listing of Hubbell Products see our full line catalog.
3
Circuit-Lock® Non-Metallic Disconnect Switches
"Suitable as Motor Disconnects"
Hubbell Circuit-Lock® Non-Metallic Disconnect Switches
comply with both the controller and disconnect requirements
of the NEC®, making them ideal for meeting line-of-sight
requirements in a variety of industrial environments. They
feature a high visibility red handle that can be locked in
the "OFF" position to comply with OSHA lockout/tagout
regulations. For maximum reliability, the external stainless steel
hardware and rugged enclosure resist abuse and corrosion,
while a neoprene gasket ensures a watertight seal.
• Heavy duty, corrosion resistant Type 4X Valox® enclosure
• Superior safety—switches can only be turned ON with
the cover closed
• Easy installation with adjustable mounting feet and
fully removable covers
• Fused disconnect switches accept Class "J" fuses
• Unfused units are NSF Certified
FDS30
HBLDS3
Fused Disconnect Switches
3 Pole 600V AC
FDS60
Amp
Description
Catalog Number
30
Circuit-Lock fused disconnect switch.
FDS30*
60
Circuit-Lock fused disconnect switch.
FDS60*
Auxiliary contact, normally open, A600 pilot duty.
ACFSNO
Auxiliary contact, normally closed, A600 pilot duty.
ACFSNC
Unfused Disconnect Switches in Non-Metallic Enclosure**
3 Pole 600V AC
Amp
ACFSNO
30
60
HBLDS3
HBLAC1
HBLAC2
100
Description
Catalog Number
Circuit-Lock disconnect switch.
HBLDS3
Circuit-Lock disconnect switch with HBLAC1 auxiliary contact.
HBLDS3AC
Circuit-Lock disconnect switch with HBLAC2 auxiliary contact.
HBLDS3AC2
Circuit-Lock disconnect switch without conduit knockout or conduit fitting.
HBLDS3NK
Circuit-Lock disconnect switch with HBLAC1 auxiliary contact without conduit
knockout or conduit fitting.
HBLDS3ACNK
Circuit-Lock disconnect switch with 3 auxiliary contacts, w/o conduit knockouts.
Break before main break – 1 set “normally open”, 1 set “normally closed”.
Break after main break – 2 sets “normally open”, 1 set “normally closed”.
HBLDS33ACNK
Circuit-Lock disconnect switch.
HBLDS6
Circuit-Lock disconnect switch with HBLAC1 auxiliary contact.
HBLDS6AC
Circuit-Lock disconnect switch.
HBLDS10
Circuit-Lock disconnect switch with HBLAC1 auxiliary contact.
HBLDS10AC
“Break After Main Break”, 1 set of n/o contacts, 1 set of n/c contacts.
HBLAC1
“Break Before Main Break”, 1 set of n/o contacts.
HBLAC2
Note: *Class “J” fuses not included.
**Certified by NSF, International.
NEC® is a registered trademark of the National Fire Protection Association (NFPA).
Valox® is a trademark of SABIC Innovative Plastics, acquired from General Electric Company.
4
For complete listing of Hubbell Products see our full line catalog.
www.hubbell-wiring.com
MotorQuick® and Variable Frequency Drive (VFD) Switches
Plug and Play Technology
MotorQuick® combines the plug-and-play technology of Hubbell’s
LINKOSITY® power system with the versatility of Circuit-Lock® motor
disconnect switches to drastically reduce the time it takes to replace
motors. These quick disconnect switches feature lockable handles to
meet OSHA lockout/tagout regulations and include pre-wired LINKOSITY
receptacles to meet a variety of application needs. The quick disconnect
LINKOSITY terminations, combined with the ability to conveniently
pre-wire spare motors with a LINKOSITY inlet without shutting down
the entire line, reduces motor change-out time by more than 65%.
The result is equipment up and running in a fraction of the time
providing productivity and bottom-line savings.
• Plug and play design allows for faster installation
• Reduces motor change-out time by more than 65%
• Crush and impact resistant MC cables
Quick Disconnect Switches
30A 3 Pole 600V AC
Type 1 Non-Metallic Enclosure
Catalog Number
HBL1389D with one pre-wired LINKOSITY® female receptacle (load side).
HBL1389MQR
HBL1389D with 5 foot pre-wired LINKOSITY® female cable (load side).
HBL1389MQ5
HBL1389D with one pre-wired LINKOSITY male receptacle (line side) and
one pre-wired LINKOSITY® female receptacle (load side).
HBL1389MQR2
®
Type 4X Non-Metallic Enclosure
HBLDS3 with one pre-wired LINKOSITY® female receptacle (load side).
HBLDS3MQR
HBLDS3 with 5 foot pre-wired LINKOSITY female cable (load side).
HBLDS3MQ5
HBLDS3 with one pre-wired LINKOSITY® male receptacle (line side)
and one pre-wired LINKOSITY® female receptacle (load side).
HBLDS3MQR2
®
HBL1389MQR2
HBL1389MQ5
HBLDS3MQR
HBLDS3MQ5
Note: See page 6 for stainless steel option.
Accessories
Description
Catalog Number
3P 4W LINKOSITY male receptacle for installation on motor.
®
RM3004PA001
3P 4W LINKOSITY® double ended (male/female) 5-50 foot cable.
PH3004PAxxx*
Lock-on cover for LINKOSITY® connections.
PH2030C
Note: *Cables available from 5-50 feet in 5 foot increments. To purchase larger cable, replace the xxx with the required
length in feet. (Examples: PH3004PA005 = 5 foot cable, PH3004PA015 = 15 foot cable.)
Hubbell's Disconnect Switch for Variable Frequency Drives
(VFDs) prevents downtime from out-of-sequence equipment
shutdowns when using VFDs, the most common method
of controlling conveyor system motors. The HBLDS3VFD
integrates an early-break auxiliary contact installed in the
HBLDS3 30 Amp disconnect switch enclosure. The contact
interfaces directly with VFDs to execute a coast-to-stop,
preventing damage to the disconnect switch and highperformance VFD output devices.
• Thoroughly tested for effective use with VFDs
• Powers down the drive prior to opening the motor disconnect
• Prevents damage to the disconnect switch and the VFD
Unfused Disconnect Switches
30A 3 Pole 600V AC
Description
Catalog Number
Non-Metallic enclosure, Circuit-Lock disconnect switch for use with
variable frequency drives.
HBLDS3VFD
Stainless Steel enclosure, Circuit-Lock disconnect switch for use with
variable frequency drives.
HBLDS3SSVFD
www.hubbell-wiring.com
For complete listing of Hubbell Products see our full line catalog.
HBLDS3VFD
HBLDS3SSVFD
5
Disconnect Switches in Stainless Steel Enclosure
"Suitable as Motor Disconnects"
Hubbell’s stainless steel disconnect switch has been certified by
NSF International for hygiene applications in food and beverage
processing. These switched enclosures are designed for harsh
environments to withstand exposure to water, chemicals, oils and
frequent wash-downs. They feature 304 Series Stainless Steel
and are UL listed Type 4X and 12 with a high visibility red handle
that can be locked in the "OFF" position for compliance with
OSHA lockout/tagout regulations. The DIN-rail mounted switch
accommodates up to two auxiliary contacts for control circuit
applications.
• Certified by NSF for hygiene in food processing applications
• Cover is embossed with ON and OFF
• Compact footprint
•MotorQuick® option (30A only)
• Increased depth accommodates up to 1½" size conduits
Unfused Disconnect Switches in Stainless Steel Enclosure
3 Pole 600V AC
Amp
HBLDS3SS
HBLDS6SS
30
60
100
Description
Catalog Number
Circuit-Lock disconnect switch.
HBLDS3SS
Circuit-Lock disconnect switch with HBLAC1 auxiliary contact.
HBLDS3SSAC
Circuit-Lock disconnect switch for use with variable frequency drives.
HBLDS3SSVFD
Circuit-Lock disconnect switch.
HBLDS6SS
Circuit-Lock disconnect switch with HBLAC1 auxiliary contact.
HBLDS6SSAC
Circuit-Lock disconnect switch.
HBLDS10SS
Circuit-Lock disconnect switch with HBLAC1 auxiliary contact.
HBLDS10SSAC
MotorQuick® Unfused Disconnect Switches in Stainless Steel Enclosures
3 Pole 600V AC
Amp
HBLDS3SSMQR
30
Description
Catalog Number
HBLDS3SS with one pre-wired LINKOSITY® female receptacle (load side).
HBLDS3SSMQR
HBLDS3SS with 5 foot pre-wired LINKOSITY® female cable (load side).
HBLDS3SSMQ5
HBLDS3SS with one pre-wired LINKOSITY male receptacle (line side) and
one pre-wired LINKOSITY® female receptacle (load side).
HBLDS3SSMQR2
®
Accessories
HBLAC1
6
HBLAC2
Description
Catalog Number
“Break After Main Break”, 1 set of n/o contacts, 1 set of n/c contacts.
HBLAC1
“Break Before Main Break”, 1 set of n/o contacts.
HBLAC2
For complete listing of Hubbell Products see our full line catalog.
www.hubbell-wiring.com
Hazardous Location Unfused Disconnect Switches,
Mechanical Interlocks and Plugs
Heavy Duty Industrial Environments
Hubbell’s hazardous location unfused disconnect and mechanical
interlock switches are ideal for applications with the presence of
flammable gases or vapors, or ignitable dusts and fibers. They
are also suitable for use in outdoor or indoor damp, wet and dirty
locations or in areas where frequent wash-downs, heavy rain or
water spray routinely occurs. Compact in size to reduce cost
over industry standard sizes, these switches are easy to position
on the wall or piece of equipment. The enclosures are made of
copper-free aluminum and have a polyester/epoxy finish to prevent
corrosion. The high visibility handles can be locked to meet OSHA
lockout/tagout regulations.
•Compact size provides application flexibility and cost savings
•Fewer cover bolts reduces installation and maintenance time
•Removable ductile mounting lugs adjust to irregular mounting surfaces
•UL 98 certified switch
Class I, Div. 1 & 2, Groups B,C,D
Class l, Zones 1 & 2, Groups llB+ H2, llA
Class II, Div. 1 & 2, Groups E,F,G
Class III
NEMA 3, 4, 4X, 7(B,C,D), 9(E,F,G)
Unfused Disconnect Switches
3 Pole 600V AC/230V DC
Amp
30
60
100
Description
Catalog Number
Disconnect switch.
HBLB7NFD13A
Disconnect switch with auxiliary contact.
HBLB7NFD13AA
Disconnect switch.
HBLB7NFD26A
Disconnect switch with auxiliary contact.
HBLB7NFD26AA
Disconnect switch.
HBLB7NFD21A
Disconnect switch with auxiliary contact.
HBLB7NFD21AA
HBLB7NFD13A
Hubbell hazardous location mechanical interlocks and plugs offer
superior safety. The plug and switch are interlocked so that the
switch cannot be turned “ON” without the plug fully inserted, and
the plug cannot be removed when the switch is in the “ON” position.
The switch features a copper-free aluminum construction with
epoxy finish and a chemical-resistant Valox® handle mechanism.
HBLB7NFD26A
•Plug and switch are interlocked for superior safety
•UL1686 C1 listed and fully interchangeable with other UL1686 C1 devices
•Compact size and footprint for easy placement
•NEMA 4X with receptacle lid turned shut or with plug locking ring tightened
Unfused Mechanical Interlocks and Plugs
Amp
30
60
Poles/Wires
Voltage AC
Receptacle
Plug
3 Pole, 2 Wire
600V AC
HBLVSQ3023
HBLVP3385
4 Pole, 3 Wire
600V AC
HBLVSQ3034
HBLVP3485
3 Pole, 2 Wire
600V AC
HBLVSQ6023
HBLVP6385
4 Pole, 3 Wire
600V AC
HBLVSQ6034
HBLVP6485
Note: HBLVSQ Series 30A models come standard with 1" drilled and tapped conduit openings top and bottom plus two 1" x ¾"
reducers and one ¾" close-up plug for maximum flexibility.
60A models come with one 1½" opening on top and bottom and one 1½" close-up plug.
HBLVSQ3034
HBLVP3485
Valox® is a trademark of SABIC Innovative Plastics, acquired from General Electric Company.
www.hubbell-wiring.com
For complete listing of Hubbell Products see our full line catalog.
7
Circuit-Lock® Pin and Sleeve Mechanical Interlocks
IP67
20, 30, 60 and 100 Ampere – North American Ratings,
32 Ampere – International Rating
SUITABILITY
Hubbell Circuit-Lock® Pin and Sleeve Mechanical Interlocks are a
revolutionary design that incorporates a disconnect switch and pin
and sleeve receptacle in a compact non-metallic unit. These devices
offer maximum safety by preventing users from mating or breaking
a circuit under load—Hubbell’s interlock mechanism detects the
presence of a plug and prevents it from being removed when the
switch is in the "ON" position. It features a high visibility red handle
that can be locked to meet OSHA lockout/tagout regulations,
and the enclosure door can be locked to prevent unauthorized
access. The rugged, corrosion-resistant Type 4X Valox® enclosure
features adjustable mounting feet for flexible installation, while the
receptacle’s spring-loaded cover with gasket is dust tight and
provides a watertight seal when turned and locked.
•
•
•
•
•
Mechanically interlocked to prevent mating and breaking under load
Available in both IEC and UL1686-C1 Insulgrip® styles
Fused disconnects accept Class "J" fuses
Fully removable door for ease of wiring
IEC reverse service units available for safely connecting generators
Circuit-Lock® Pin and Sleeve Mechanical Interlocks
Amp
20
Poles/Wires
Voltage AC
Unfused
Reverse Service
Fused*
120/240V
HBL420MI12W
—
—
3Ø 240V
HBL420MI9W
—
—
3Ø 480V
HBL420MI7W
—
—
120V
HBL330MI4W
—
—
240V
HBL330MI6W
—
—
480V
HBL330MI7W
—
—
120/240V
HBL430MI12W
—
HBL430MIF12W
3Ø 240V
HBL430MI9W
HBL430MI9WR
HBL430MIF9W
3Ø 480V
HBL430MI7W
HBL430MI7WR
HBL430MIF7W
4 Pole,
5 Wire
3ØY 120/208V
HBL530MI9W
—
—
3ØY 277/480V
HBL530MI7W
—
HBL530MIF7W
3 Pole, 4 Wire
380V 50HZ-440V 60Hz
HBL432MI3W
—
—
120V
HBL360MI4W
—
—
240V
HBL360MI6W
—
—
480V
HBL360MI7W
—
—
120/240V
HBL460MI12W
HBL460MI12WR
HBL460MIF12W
3Ø 240V
HBL460MI9W
HBL460MI9WR
HBL460MIF9W
3Ø 480V
HBL460MI7W
HBL460MI7WR
HBL460MIF7W
4 Pole,
5 Wire
3ØY 120/208V
HBL560MI9W
—
HBL560MIF9W
3ØY 277/480V
HBL560MI7W
—
—
2 Pole, 3 Wire
240V
HBL3100MI6W
—
—
120/240V
HBL4100MI12W
HBL4100MI12WR —
3Ø 240V
HBL4100MI9W
HBL4100MI9WR
—
3Ø 480V
HBL4100MI7W
HBL4100MI7WR
—
3ØY 120/208V
HBL5100MI9W
—
—
3 Pole,
4 Wire
2 Pole,
3 Wire
30
HBL420MI7W
32
3 Pole,
4 Wire
2 Pole,
3 Wire
60
HBL430MIF7W
100
3 Pole,
4 Wire
3 Pole,
4 Wire
4 Pole, 5 Wire
Insulgrip® Mechanical Interlocks - Style II
HBL430MIS2W
Amp
Poles/Wires
Voltage
Unfused
Fused*
30
60
3 Pole, 4 Wire
3 Pole, 4 Wire
600V AC/250V DC
600V AC/250V DC
HBL430MIS2W
HBL460MIS2W
HBL430MIFS2W
HBL460MIFS2W
Note: 20A, 30A, 32A – 1 inch N.P.T. hub supplied; 60A, 100A – 1¼ inch hub supplied.
*Class “J” fuses not included.
Valox® is a trademark of SABIC Innovative Plastics, acquired from General Electric Company.
8
For complete listing of Hubbell Products see our full line catalog.
www.hubbell-wiring.com
Twist-Lock® Mechanical Interlock Switched Safety Enclosures
Circuit-Lock® Unfused Safety Shroud® Twist-Lock®
IP66
SUITABILITY
Hubbell's Twist-Lock® Mechanical Interlock integrates an angled
watertight Hubbell Safety-Shroud® Twist-Lock® receptacle with a
linked disconnect switch that prevents making lazy connection or
breaking the circuit while under load. The switch cannot be turned
"ON" until the plug is properly inserted and locked, and the plug
cannot be removed until the switch is turned "OFF". The pre-molded
conduit entry hole is offset to prevent condensation from reaching
interior components, while speeding installation by making it easier
to pull conductors. Twist-Lock® Mechanical Interlocks offer superior
flexibility—they can be used in a horizontal or vertical position, and
the Type 4X corrosion-resistant enclosure allows for top, bottom or
back feed options.
• Mechanically interlocked to prevent mating and breaking under load
• Switched enclosures sold separately from receptacle for custom
electrical configurations
• Type 4X rated system with and without the plug inserted
• Horsepower rated switch
• Enclosure is designed for top, bottom or back feed options
Switched Safety Enclosures (Receptacles Sold Separately Listed Below)
Description
Ratings
Catalog Number
Mechanical Interlock accommodates Amperage and voltage ratings will be determined
HBLMITL
20A or 30A Watertight Safety-Shroud® by the choice of the Watertight Safety-Shroud®
Twist-Lock® receptacles.
Twist-Lock® selected. Supplied with ¾" N.P.T. Hub.
HBLMITL Accepts the Following Watertight Safety-Shroud® Twist-Lock® Receptacles:
Amp
Poles/Wires
2 Pole,
3 Wire
20
3 Pole,
4 Wire
NEMA Config.
Ref. Number
Max. HP
Rating*
Receptacle
Mating Plug
120
L5-20
1
HBL2310SW
HBL2311SW
208-240
L6-20
2.5
HBL2320SW
HBL2321SW
277
L7-20
3
HBL2330SW
HBL2331SW
120/240
L14-20
2.5
HBL2410SW
HBL2411SW
240 3Ø
L15-20
5 ([email protected])
HBL2420SW
HBL2421SW
480 3Ø
L16-20
10
HBL2430SW
HBL2431SW
L21-20
3
HBL2510SW
HBL2511SW
120
L5-30
1
HBL2610SW
HBL2611SW
208-240
L6-30
3
HBL2620SW
HBL2621SW
120/240
L14-30
3
HBL2710SW
HBL2711SW
240 3Ø
L15-30
7.5
HBL2720SW
HBL2721SW
480 3Ø
L16-30
15
HBL2730SW
HBL2731SW
600 3Ø
L17-30
15
HBL2740SW
HBL2741SW
120/208 3ØY
L21-30
7.5
HBL2810SW
HBL2811SW
277/480
L22-30
7.5
HBL2820SW
HBL2821SW
347/600
L23-30
7.5
HBL2830SW
HBL2831SW
Voltage AC
4 Pole, 5 Wire 120/208 3ØY
2 Pole,
3 Wire
30
3 Pole,
4 Wire
4 Pole,
5 Wire
HBLMITL
HBL2320SW
HBL2321SW
Note: *HP ratings for the final unit are determined by the HP rating of the switch, limited by the full load current capability of the
receptacle at 80% of rated current, number of phases and line voltage. HP ratings listed above are AC only.
Switched Safety Enclosures (Receptacles Sold Separately**)
Description
Ratings
Catalog Number
Switched Twist-Lock® enclosure
accommodates any NEMA 2 pole,
3 wire to 4 pole, 5 wire grounding
receptacle.
Switched enclosure for use with
3 pole 4 wire 30A Hubbellock®
receptacle.
Amperage, voltage, and horsepower ratings
will be determined by the choice of the NEMA
20 or 30A Twist-Lock® receptacle selected.
SETL3
Amperage, voltage, and horsepower ratings
will be determined by the choice of the
4 wire Hubbellock®.
SEHBL3
SETL3
SEHBL3
Note: **Please see the full line catalog for a complete selection of Twist-Lock and Hubbellock devices.
www.hubbell-wiring.com
For complete listing of Hubbell Products see our full line catalog.
9
600V AC Manual Motor Controllers/Disconnects
“Suitable as Motor Disconnects”
For use in nearly any industrial environment, Hubbell AC Manual Motor
Controllers/Disconnects can be easily integrated into equipment and
enclosures for either box or panel-mount installation. Rated “Suitable
as Motor Disconnect,” they feature a quick make and slow break
operation that ensures reliability and long life. Hubbell AC Manual
Motor Controllers/Disconnects have a 10,000 Amp high fault short
circuit withstand rating and a heat-resistant thermoset body that
provides resistant to arc tracking and superior dielectric strength.
The 30 Amp controller features a brass terminal screw clamping plate
for secure back or side wiring, and the 60 Amp version is available
with front or back wiring.
• All switches are “Suitable as a Motor Disconnect”
• Strong “ON/OFF” action with a quick make and
slow break operation
• Heat-resistant thermoset body provides superior
dielectric strength
• Optional side guards available for close wall
applications and finger safe environments
30A, 40A and 50A
60A and 85A
600V AC Manual Motor Controllers/Disconnects
HP Rating
Amp
30
HBL7810D
HBL7853D
40
50
60
HBL7863D
HBLFG30
85
Poles
120V AC
1Ø
240V AC
3Ø
480V AC
3Ø
600V AC
3Ø
Catalog Number
Toggle-type
Wire
2
Standard
Back/Side
2
5
10
15
HBL7832D
2
Short
Back/Side
2
5
10
15
HBL7832DS
2
Standard
Back/Side
2
5
10
15
HBL7832DX*
3
Standard
Back/Side
3
7.5
15
20
HBL7810D
3
Short
Back/Side
3
7.5
15
20
HBL7810DS
2
Standard
Side
2
5
10
15
HBL7842D
3
Standard
Side
3
7.5
15
20
HBL7843D
2
Standard
Side
2
5
10
15
HBL7852D
3
Standard
Side
3
7.5
15
25
HBL7853D
2
Standard
Back
—
10
15
20
HBL7862D
3
Standard
Back
—
10
25
30
HBL7863D
2
Standard
Front
—
10
15
20
HBL7862FWD
3
Standard
Front
—
10
25
30
HBL7863FWD
2
Standard
Back
—
10
15
20
HBL7882D
3
Standard
Back
—
10
25
40
HBL7883D
Optional Side Guard, for close wall applications and finger safe environments.
HBLFG30
Note: *HBL7832DX is a 50 piece bulk pack of the HBL7832D.
10
For complete listing of Hubbell Products see our full line catalog.
www.hubbell-wiring.com
NEMA Disconnect Switches
“Suitable as Motor Disconnects”
Circuit-Lock® NEMA 1 Enclosures with Switch
Ideal for use in industrial environments, i.e. conveyor systems, industrial fans, etc.
HP Rating
Amp
Poles
30
30
Enclosure Material
120V AC
1Ø
240V AC
3Ø
480V AC
3Ø
600V AC
3Ø
Catalog Number
2
Thermoplastic/Steel
2
5
10
15
HBL1392D
3
Thermoplastic/Steel
3
7.5
15
20
HBL1389D
2
Aluminum
2
5
10
15
HBL1372D
3
Aluminum
3
7.5
15
20
HBL1379D
HBL1389D
HBL1379D
HBL1390
HBL1370
HBL13R22D
HBL13R12D
HBL13R89D
HBL16R93D
HBL16S63D
HBL13X33D
Circuit-Lock® NEMA 1 Enclosures without Switch
For use with 30A switches shown on page 10.
No. Equipment
Grounds
Description
Cover Material
Base Material
For use with 30A switch.
Thermoplastic
Steel
1
Catalog Number
HBL1390
For use with 30A switch.
Aluminum
Aluminum
2
HBL1370
Circuit-Lock® NEMA 3/3R Enclosures with Switch*
Ideal for use on outdoor equipment.
HP Rating
Amp
Poles
30
30
Enclosure Material
120V AC
1Ø
240V AC
3Ø
480V AC
3Ø
600V AC
3Ø
Catalog Number
2
Thermoplastic
2
5
10
15
HBL13R22D
3
Thermoplastic
3
7.5
15
20
HBL13R23D
2
Aluminum
2
5
10
15
HBL13R12D†
3
Aluminum
3
7.5
15
20
HBL13R13D†
240V AC
3Ø
480V AC
3Ø
600V AC
3Ø
Catalog Number
Note: *Drill weep-hole to alter from NEMA 3 to NEMA 3R.
†
Equipped with HBLFG30 sidewall insulation barriers.
Circuit-Lock® NEMA 3R Enclosures with Switch
Ideal for use in outdoor environments.
HP Rating
Amp
Poles
30
60
Enclosure Material
120V AC
1Ø
2
Aluminum
2
5
10
15
HBL13R92D
3
Aluminum
3
7.5
15
20
HBL13R89D
2
Aluminum
—
10
15
20
HBL16R92D
3
Aluminum
—
10
25
30
HBL16R93D
Circuit-Lock® NEMA 3R Enclosures without Switch
For use with switches shown on page 10.
Description
Enclosure Material
Catalog Number
For use with 30A switch.
Aluminum
HBL13R90
For use with 60A switch.
Aluminum
HBL16R90
Circuit-Lock® NEMA 4X Enclosures with Rotary Handle
Ideal for use in environments where wash-down is necessary, i.e. food processing, laboratories, etc.
HP Rating
Amp
30
60
Poles
Enclosure Material
120V AC
1Ø
240V AC
3Ø
480V AC
3Ø
600V AC
3Ø
Catalog Number
2
Stainless Steel
3
7.5
15
20
HBL13S33D
3
Valox®
3
7.5
15
20
HBL13X33D
3
Stainless Steel
—
10
25
30
HBL16S63D
3
Valox®
—
10
25
30
HBL16X63D
Finger Guard option for 30A switch.
HBLFG30
NO/NC auxiliary contact, 10A 120/250V AC for 30 and 60 Amp rotary switches.
HBLAUX
Valox® is a trademark of SABIC Innovative Plastics, acquired from General Electric Company.
www.hubbell-wiring.com
For complete listing of Hubbell Products see our full line catalog.
11
CIRCUIT-LOCK® and MOTORQUICK®
®
Manual Motor Controllers and Disconnects
Wiring Device-Kellems
Quick Reference Guide
Circuit-Lock® Switched Enclosures
HBL1379D
HBL13R89D
HBLDS3
HBL16R93D
HBL13S33D
FDS30
Catalog Number
Amp Description
HBL1372D
HBL1379D
HBL1392D
HBL1389D
HBL13R22D
HBL13R23D
HBL13R12D
HBL13R13D
HBL13R92D
HBL13R89D
HBL16R92D
HBL16R93D
HBLDS3*
HBLDS3AC*
HBLDS3NK
HBLDS3ACNK
HBLDS33ACNK
HBLDS6*
HBLDS6AC*
HBLDS10*
HBLDS10AC*
HBL13S33D
HBL13X33D
HBL16S63D
HBL16X63D
FDS30
FDS60
30
30
30
30
30
30
30
30
30
30
60
60
30
30
30
30
30
60
60
100
100
30
30
60
60
30
60
NEMA 1 Aluminum
NEMA 1 Aluminum
NEMA 1 Non-Metallic
NEMA 1 Non-Metallic
NEMA 3/3R Non-Metallic
NEMA 3/3R Non-Metallic
NEMA 3R Die Cast Aluminum
NEMA 3R Die Cast Aluminum
NEMA 3R Aluminum
NEMA 3R Aluminum
NEMA 3R Aluminum
NEMA 3R Aluminum
TYPE 4X Non-Metallic
TYPE 4X Non-Metallic
TYPE 4X Non-Metallic
TYPE 4X Non-Metallic
TYPE 4X Non-Metallic
TYPE 4X Non-Metallic
TYPE 4X Non-Metallic
TYPE 4X Non-Metallic
TYPE 4X Non-Metallic
NEMA 4X Stainless Steel
NEMA 4X Non-Metallic
NEMA 4X Stainless Steel
NEMA 4X Non-Metallic
NEMA 4X Non-Metallic Fused Disconnect
NEMA 4X Non-Metallic Fused Disconnect
HP
Phase Poles
1
3
1
3
1
3
1
3
1
3
1
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
2
3
2
3
2
3
2
3
2
3
2
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
120
240
480
600
2
3
2
3
2
3
2
3
2
3
—
—
1
1
1
1
1
7.5
7.5
7.5
7.5
3
3
—
—
2
3
5
7.5
5
7.5
5
7.5
5
7.5
5
7.5
10
10
7.5
7.5
7.5
7.5
5
30
30
30
30
7.5
7.5
10
10
7.5
15
10
15
10
15
10
15
10
15
10
15
15
25
15
15
15
15
10
50
50
50
50
15
15
25
25
15
30
15
20
15
20
15
20
15
20
15
20
20
30
15
15
15
15
10
50
50
50
50
20
20
30
30
20
40
120
240
480
600
3
3
3
1
1
1
7.5
7.5
7.5
7.5
7.5
7.5
15
15
15
15
15
15
20
20
20
15
15
15
120
240
480
600
2
2
2
3
3
2
3
2
3
—
—
—
—
—
—
5
5
5
7.5
7.5
5
7.5
5
7.5
10
10
10
10
10
10
10
10
10
15
15
10
15
10
15
15
25
15
25
15
25
15
15
15
20
20
15
20
15
25
20
30
20
30
20
40
Note: *Stainless steel version carries the same HP rating.
MotorQuick® Disconnect Switches
Catalog Number
HBLDS3MQR
HBL1389MQR
HBL1389MQ5
HBL1389MQR2
HBLDS3MQR
HBLDS3MQ5
HBLDS3MQR2
HBLDS3MQ5
Amp Description
30
30
30
30
30
30
NEMA 1 Non-Metallic
NEMA 1 Non-Metallic
NEMA 1 Non-Metallic
NEMA 4X Non-Metallic
NEMA 4X Non-Metallic
NEMA 4X Non-Metallic
HP
Phase Poles
3
3
3
3
3
3
3
3
3
3
3
3
Circuit-Lock® Switches
Catalog Number
HBL7810D
HBL7853D
HBL7843D
HBL7863D
HBL7832D
HBL7832DS
HBL7832DX
HBL7810D
HBL7810DS
HBL7842D
HBL7843D
HBL7852D
HBL7853D
HBL7862D
HBL7863D
HBL7862FWD
HBL7863FWD
HBL7882D
HBL7883D
Amp Description
30
30
30
30
30
40
40
50
50
60
60
60
60
85
85
Toggle Switch
Short Toggle Switch
Toggle Switch, Bulk Pack
Toggle Switch
Short Toggle Switch
Toggle Switch
Toggle Switch
Toggle Switch
Toggle Switch
Toggle Switch
Toggle Switch
Toggle Switch – Front Wire
Toggle Switch – Front Wire
Toggle Switch
Toggle Switch
HP
Phase Poles
1
1
1
3
3
1
3
1
3
1
3
1
3
1
3
2
2
2
3
3
2
3
2
3
2
3
2
3
2
3
®
Wiring Device-Kellems
www.hubbell-wiring.com
Hubbell Wiring Device-Kellems • Hubbell Incorporated (Delaware) • 40 Waterview Drive • Shelton, CT 06484 • Phone (800) 288-6000 • FAX (800) 255-1031
Printed in U.S.A. Specifications subject to change without notice. ® Registered trademarks of Hubbell Incorporated.
WLBSB001 11/12
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement