Sony DSR 1800, DSR 1800P Digital Video Cassette Recorder Operating Instructions

Sony DSR 1800, DSR 1800P Digital Video Cassette Recorder Operating Instructions

Below you will find brief information for Digital Video Cassette Recorder DSR 1800, Digital Video Cassette Recorder DSR 1800P. The DSR-1800/1800P is a 1/4-inch digital video cassette recorder using the DVCAM digital recording format. It achieves stable, superb picture quality by digitally processing video signals separated into color difference signals and luminance signals (component method). The unit is equipped with a variety of functions needed for videocassette recorders and players used in professional digital video editing systems. It supports the ClipLinkTM function developed by Sony Corporation for highly efficient video editing. When connected to a Sony EditStationTM, the unit serves as part of a powerful non-linear editing system*. The unit is also equipped with a full-fledged analog interface to support hybrid systems that combine conventional analog equipment with digital equipment.

advertisement

Assistant Bot

Need help? Our chatbot has already read the manual and is ready to assist you. Feel free to ask any questions about the device, but providing details will make the conversation more productive.

DSR 1800, DSR 1800P Operating Instructions | Manualzz
3-204-675-12(2)
Digital
Videocassette
Recorder
Operating Instructions
Before operating the unit, please read this manual
thoroughly and retain it for future reference.
DSR-1800/1800P
© 2000 Sony Corporation
Owner’s Record
The model and serial numbers are located at the rear.
Record these numbers in the spaces provided below. Refer
to them whenever you call upon your Sony dealer
regarding this product.
Model No.
WARNING: THIS WARNING IS APPLICABLE FOR
USA ONLY.
Using this unit at a voltage other than 120 V may require
the use of a different line cord or attachment plug, or both.
To reduce the risk of fire or electric shock, refer servicing
to qualified service personnel.
Serial No.
WARNING
To prevent fire or shock hazard, do not
expose the unit to rain or moisture.
To avoid electrical shock, do not open the
cabinet. Refer servicing to qualified
personnel only.
For customers in the USA
This equipment has been tested and found to comply with
the limits for a Class A digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when
the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in
accordance with the instruction manual, may cause
harmful interference to radio communications. Operation
of this equipment in a residential area is likely to cause
harmful interference in which case the user will be
required to correct the interference at his own expense.
THIS APPARATUS MUST BE EARTHED.
You are cautioned that any changes or modifications not
expressly approved in this manual could void your
authority to operate this equipment.
The shielded interface cable recommended in this manual
must be used with this equipment in order to comply with
the limits for a digital device pursuant to Subpart B of Part
15 of FCC Rules.
Caution
Television programs, films, video tapes and other
materials may be copyrighted.
Unauthorized recording of such material may be contrary
to the provisions of the copyright laws.
This symbol is intended to alert the user to
the presence of uninsulated “dangerous
voltage” within the product’s enclosure
that may be of sufficient magnitude to
constitute a risk of electric shock to
persons.
This symbol is intended to alert the user to
the presence of important operating and
maintenance (servicing) instructions in
the literature accompanying the
appliance.
2
For customers in Europe (DSR-1800P only)
This product with the CE marking complies with both the
EMC Directive (89/336/EEC) and the Low Voltage
Directive (73/23/EEC) issued by the Commission of the
European Community.
Compliance with these directives implies conformity to
the following European standards:
• EN60065: Product Safety
• EN55103-1: Electromagnetic Interference (Emission)
• EN55103-2: Electromagnetic Susceptibility (Immunity)
This product is intended for use in the following
Electromagnetic Environment(s):
E1 (residential), E2 (commercial and light industrial), E3
(urban outdoors) and E4 (controlled EMC environment,
ex. TV studio).
Table of Contents
Chapter 1 Overview
Features........................................................................5
DVCAM Format ............................................................. 5
A Wealth of Interfaces .................................................... 6
Facilities for High-Efficiency Editing............................. 6
Other Features ................................................................. 7
Optional Accessories....................................................... 7
Location and Function of Parts..................................8
Front Panel ...................................................................... 8
Rear Panel ..................................................................... 16
Chapter 2 Recording and Playback
Usable Cassettes.......................................................21
Inserting and Ejecting Cassettes ................................... 23
Recording...................................................................25
Settings for Recording .................................................. 25
Recording Procedure..................................................... 28
Playback .....................................................................31
Settings for Playback .................................................... 31
Playback Procedure....................................................... 32
Repeat Playback—Automatic Cyclical Playback ......... 34
Setting Points A and B for Repeat Playback................. 34
Cuing Up to Any Desired Position Set as Point
A or B .................................................................. 39
Chapter 3 Convenient Functions for Editing Operation
Setting the Time Data ................................................41
Displaying Time Data and Operation Mode
Indications ........................................................... 41
Using the Internal Time Code Generator ...................... 43
Synchronizing Internal and External Time Codes ........ 45
Rerecording the Time Code—TC Insert Function........ 45
High-Speed and Low-Speed Search—Quickly
and Accurately Determining Editing Points .....48
Search Operations via External Equipment .................. 48
Search Operations on This Unit .................................... 49
Digitally Dubbing Signals in DVCAM Format..........50
3
Chapter 4 Menu Settings
Menu Organization ....................................................53
Menu Contents...........................................................56
Setup Menu ................................................................... 56
Auto Mode (AUTO FUNCTION) Execution Menu..... 69
Changing Menu Settings ..........................................70
Buttons Used to Change Settings.................................. 70
Changing the Settings of Basic Items ........................... 70
Displaying Enhanced Items .......................................... 72
Changing the Settings of Enhanced Items .................... 72
Returning Menu Settings to Their Factory Default
Settings ................................................................ 73
Displaying Supplementary Status Information.......74
Chapter 5 Connections and Settings
Connections for a Digital Non-Linear Editing
System .................................................................77
Connections for a Cut Editing System ....................79
Connections for an A/B Roll Editing System ..........80
Connections for SDTI (QSDI) Dubbing ....................86
Connections for Analog Recording .........................87
Adjusting the Sync and Subcarrier Phases ............88
Chapter 6 Maintenance and Troubleshooting
Maintenance ...............................................................91
Condensation................................................................. 91
Regular Checks ............................................................. 91
Head Cleaning............................................................... 93
Troubleshooting ........................................................94
Error Messages.............................................................. 96
Alarm Messages ............................................................ 96
Appendixes
Precautions ................................................................99
Specifications ..........................................................100
ClipLink Guide .........................................................104
What Is ClipLink? ....................................................... 104
Example System Configuration and Operation
Flow ................................................................... 105
Data Generated When Shooting.................................. 106
Glossary ...................................................................109
Index .........................................................................111
4
Overview
Features
The DSR-1800/1800P is a 1/4-inch digital video cassette
recorder using the DVCAM digital recording format. It
achieves stable, superb picture quality by digitally
processing video signals separated into color difference
signals and luminance signals (component method).
The unit is equipped with a variety of functions needed for
videocassette recorders and players used in professional
digital video editing systems. It supports the ClipLinkTM
function developed by Sony Corporation for highly
efficient video editing. When connected to a Sony
EditStationTM, the unit serves as part of a powerful nonlinear editing system*.
The unit is also equipped with a full-fledged analog
interface to support hybrid systems that combine
conventional analog equipment with digital equipment.
Chapter
1
Because the recording is digital, multi-generation dubbing
can be performed with virtually no deterioration of quality.
Wide track pitch
The recording track pitch is 15 µm, fully 50 percent wider
than the 10-µm track pitch of the DV format. Thanks to this
feature, the DVCAM format sufficiently meets the
reliability and precision requirements of professional
editing.
High-quality PCM digital audio
PCM recording makes for a wide dynamic range and a
high signal-to-noise ratio, thereby enhancing sound
quality.
There are two recording modes: 2-channel mode (48-kHz
sampling and 16-bit quantization), which offers sound
quality equivalent to the DAT (Digital Audio Tape)
format, or 4-channel mode (32-kHz sampling and 12-bit
quantization).
* Non-linear editing: This is an editing method that uses video and audio
signals digitally encoded and recorded on a hard disk as digital data. When
compared with conventional (linear) editing methods, non-linear editing
offers vastly improved efficiency in editing operations, for example, by
eliminating tape transport time.
Playback compatibility with DV and
DVCPRO formats
The main features of the unit are described in the
following.
A DV cassette recorded on a DV format VCR as well as a
DVCPRO (25M) format recorded cassette can be played
back on this unit.
DVCAM Format
DVCAM is based on the consumer DV format, which uses
the 4:1:1 component digital format, and provides a 1/4-inch
digital recording format for professional use.
Note
When playing back a tape recorded in DVCPRO (25M)
format, the SDTI and i.LINK outputs (see “Digital
interfaces” on page 6) of this unit are muted. Furthermore,
it is not possible to playback the cue-audio track of the
tape.
High picture quality, high stability
Video signals are separated into color difference signals
and luminance signals, which are encoded and compressed
to one-fifth size before being recorded to ensure stable and
superb picture quality.
Features
5
Support for three cassette sizes
Chapter 1 Overview
There are two sizes of DVCAM cassette: standard and
mini. You can use either size with this unit.
The unit also accepts L and M sizes of DVCPRO cassette.
• When a cassette is inserted, the reel mechanism of the
unit automatically adjusts to the size of the inserted
cassette.
• The capacity of a standard cassette is 184 minutes of
recording/playback, and that of a mini cassette is 40
minutes.
Facilities for High-Efficiency Editing
The unit provides an abundance of functions that enhance
editing efficiency and precision.
Cross-fade editing
For audio editing, you can select from cut-in editing, fadein/fade-out editing, and cross-fade editing.
Support for ClipLink function
A Wealth of Interfaces
Digital interfaces
The following optional digital interfaces are available for
use with the unit.
SDTI (QSDI)* (optional DSBK-1802 SDTI (QSDI)
Input/Output Board): When the unit is fitted with the
optional DSBK-1802 board, SDTI (QSDI)-format
video, audio and time code signals can be transferred
between the unit and the Sony EditStation at normal
speed. When this unit is connected to another
DVCAM VCR, it is possible to copy compressed
signals between the two VCRs.
SDI (serial digital interface)/AES/EBU (optional
DSBK-1801 SDI/AES/EBU Input/Output Board):
When the unit is fitted with the optional DSBK-1801
board, it can input and output D1 (component) format
digital video and audio signals and also AES/EBUformat digital audio signals.
i.LINK (DV)** (optional DSBK-1803 i.LINK/DV
Input/Output Board): When the unit is fitted with the
optional DSBK-1803 board (i.LINK compatible), it
can input and output digital video and audio signals in
DV format.
* SDTI is the name of a standard interface established as SMPTE 305M.
QSDI is a type of SDTI. This unit uses SDTI to transmit DV data, and the
input/output connectors are labeled “SDTI (QSDI).”
** i.LINK and are trademarks and indicate that this product is in agreement
with IEEE1394-1995 specifications and their revisions.
Analog interfaces
The unit also comes with analog interfaces enabling it to be
connected to analog video and audio equipment.
Analog video: These interfaces include a component
interface, composite interface, and S-video interface.
Analog audio: Four channels each of input and output are
provided. It is also possible to connect a microphone to
the unit.
6
Features
In response to commands sent from the EditStation, index
pictures recorded on tape or ClipLink log data recorded in
the cassette memory can be transferred to the EditStation.
The EditStation operator can then efficiently use these
pictures and data in a preliminary editing session.
For an overview of the ClipLink function, see the appendix
“ClipLink Guide” (page 104).
Internal time code generator and reader
An internal time code generator and reader enables time
code compliant with SMPTE (for DSR-1800)/EBU (DSR1800P) format to be recorded and played back. This allows
editing to single frame precision.
Outputting or inputting time code (LTC) to or from an
external device is also possible using the TIME CODE IN/
OUT connectors.
The unit is also compatible with VITC.
Remote control
The unit can be operated by remote control from an editing
control unit that supports the RS-422A interface or from an
optional SIRCS*-compatible remote control unit such as
the DSRM-10.
* SIRCS (Sony Integrated Remote Control System): A command protocol
to remote control Sony professional videocassette recorders/players.
Playback control using search dial
The search dial on the front panel of the unit allows you to
carry out playback operation in jog or shuttle mode
without requiring an external editing control unit or remote
control unit to be connected to the unit.
High-speed search function
The unit has a picture search function that allows you to
view color picture at playback speeds up to 85 times
normal speed in forward and reverse directions.
When remote-controlling this unit in shuttle mode from an
editing control unit or a remote control unit, you can search
at any speed in the range 0 (still) to 60 times normal speed
in both directions. You can also search frame-by-frame in
jog mode.
At search speeds up to 10 times normal speed in both
directions, you can also hear playback audio.
Compatible with wide-screen aspect ratio
(16:9)
Digital jog sound function
Rack mountable
1
When searching at speeds in the range +1 to + /30 or
−1/30 to −1* times normal speed, the digital jog sound
function is enabled. The audio signal is saved in temporary
memory, and replayed according to the search speed. This
allows searching on the sound track.
* The positive direction refers to forward movement of the tape, and the
negative direction to reverse movement.
Video process control
For analog video output and SDI-format video output, you
can adjust the video output level, chroma signal output
level, setup level (for DSR-1800), black level (for DSR1800P), and chroma phase.
When you use the optional RMM-130 Rack Mount Kit,
you can mount this unit onto an EIA-standard 19-inch rack
(height = 4 units).
Optional Accessories
DSBK-1801 SDI/AES/EBU Input/Output
Board
When installed in the unit, this optional board enables
digital video and audio signals in the D1 format and also
AES/EBU-format digital audio signals to be transferred
between this unit and digital Betacam VCRs or other
digital equipment.
Other Features
DSBK-1802 SDTI (QSDI) Input/Output
Board
Menu system for functionality and
operation settings
This interface allows video, audio and time code signals in
SDTI (QSDI) format to be transferred at normal speed
between this unit and the Sony EditStation. When this unit
is connected to another DVCAM VCR, it is possible to
copy compressed signals between the two VCRs.
The unit provides a menu system to make its various
functions easier to use and set up its operation conditions.
Superimposition function
Time code values, operation mode indications, error
messages, and other text data can be superimposed and
output in analog composite video signals.
Easy maintenance functions
Self-diagnostic/alarm function: This function
automatically detects setup and connection errors,
operation faults, and other problems. It also displays a
description of the problem, its cause, and the
recommended response on the video monitor screen or
time counter display.
Digital hours meter: The digital hours meter functions
include four kinds of tally operations for operating
hours, head drum usage hours, tape transport hours,
and tape threading/unthreading times. The tally results
can be viewed on the video monitor or the time counter
display.
Chapter 1 Overview
Using the frame memory function, the unit can show
noise-free slow-motion playback at speeds ranging from 0
to 1/2 times normal speed in both directions.
The unit can record and play back aspect ratio information.
When video accompanied by wide-screen aspect ratio
information is recorded or played back, the unit can output
the video signal also containing the aspect ratio
information.
Digital slow-motion playback
DSBK-1803 i.LINK/DV Input/Output Board
This board allows you to connect the unit to other
equipment provided with a Sony DV connector to carry
out editing or dubbing of digital video and audio signals.
RMM-130 Rack Mount Kit
This kit can be used to mount the unit onto an EIAstandard 19-inch rack.
Features
7
Location and Function of Parts
Front Panel
a POWER switch
Chapter 1 Overview
b Audio level meters
A Input selection/audio mode
display section (see page 9)
c Cassette compartment
POWER
dB
0
OVER
dB
0
dB
0
OVER
dB
0
dB
0
OVER
dB
0
dB
0
-12
1
-12
1
-12
1
-12
-20
0
-20
0
-20
0
-20
-30
-40
-60
-1
-2
-30
-40
1
-60
-1
-2
-30
-40
2
-60
-1
-2
-30
-40
3
-60
OVER
dB
INPUT
V:SDTI
SDTI
i.LINK
0
1
VIDEO
0
CH11/2
-1
AUDIO
-2
CH23/4
4
PB FS
A
COMPOSITE Y-R,B S VIDEO
SDI
SG
ANALOG AES/EBU
SDI
SG
ANALOG AES/EBU
SDI
SG
48k44.1k32k REC MODE
2CH4CH
B
MARK
B Menu control panel (inside of
the door) (see page 10)
F Remote control setting
section (see page 15)
g AUDIO INPUT LEVEL control knobs
f CONTROL S connector
e HEADPHONES connector
d PHONE LEVEL control knob
a POWER switch
Press the “ ” side to power the unit on. When the unit is
powered on, the display windows in the front panel lights.
To power the unit off, press the “ ” side of the switch.
E Search control section
(see page 14)
D Display section (see page 13)
C Tape transport control section (see page 12)
c Cassette compartment
Accepts DVCAM, DV and DVCPRO (25M)
videocassettes.
For details of usable cassettes, see page 21.
b Audio level meters
These show the audio levels of channels 1 to 4 (recording
levels in recording mode or E-E mode* and playback level
in playback mode).
* E-E mode: Abbreviation of “Electric-to-Electric mode.” In this mode,
video and audio signals input to the VCR are output after passing through
internal electric circuits, but not through magnetic conversion circuits such
as heads and tapes. This can be used to check input signals and for
adjusting input signal levels.
8
Location and Function of Parts
d PHONE LEVEL control knob
Controls the volume of the headphones connected to the
HEADPHONES connector.
e HEADPHONES connector (stereo phone jack)
Connect stereo headphones for headphone monitoring
during recording or playback.
The audio signal you want to monitor can be selected with
the MONITOR SELECT switches on the menu control
panel.
g AUDIO INPUT LEVEL control knobs
When recording, you can use these knobs to set audio input
levels for CH-1 (channel 1), CH-2, CH-3 and CH-4,
respectively.
You can make these knobs inoperative with the REC
LEVEL menu item (see page 64).
Chapter 1 Overview
f CONTROL S connector (stereo minijack)
Connect a SIRCS-compatible remote control unit such as
the DSRM-10.
A Input selection/audio mode display section
a INPUT display
b VIDEO display
c AUDIO CH1 1/2 display
d AUDIO CH2 3/4 display
e REC MODE display
f PB FS display
a INPUT display
Indicates the input signal selected with the SDTI/i.LINK
button in the INPUT SELECT section.
V:SDTI: Digital video signal in SDTI(QSDI) format
SDTI: Digital video and audio signals in SDTI(QSDI)
format
i.LINK: Digital video and audio signals in i.LINKcompatible DV format
The SDTI/i.LINK button to function fully requires the
optional DSBK-1802 and 1803 boards to be installed. The
signal without the corresponding optional board installed
in the unit can be neither selected nor indicated.
b VIDEO display
Indicates the input video signal selected with the VIDEO
IN button in the INPUT SELECT section.
COMPOSITE: Composite video signal
Y−R, B: Y, R−Y and B−Y component video signals
S VIDEO: S-video signal
SDI: SDI video signal (optional DSBK-1801 board
required)
SG: Video test signal
d AUDIO CH2 3/4 display
Indicates the input audio signal selected with the CH-2,3/4
button in the INPUT SELECT section. The indications
available are the same as for the AUDIO CH1 1/2 display
described above.
e REC MODE (audio recording mode) display
Indicates the audio recording mode (2CH or 4CH) selected
with the REC MODE menu item (see page 63).
f PB FS (playback audio sampling frequency)
display
Indicates the sampling frequency (48 kHz, 44.1 kHz or 32
kHz) at which audio is recorded on tape.
c AUDIO CH1 1/2 display
Indicates the input audio signal selected with the CH-1,1/2
button in the INPUT SELECT section.
ANALOG: Analog audio signal
AES/EBU: Digital audio signal in AES/EBU format
(optional DSBK-1801 board required)
SDI: SDI audio signal (optional DSBK-1801 board
required)
SG: Audio test signal
Location and Function of Parts
9
B Menu control panel
The menu control panel is located on the inside of the door
at the lower front of the unit. Pull the top of the door to
open it.
a MONITOR SELECT switches
Chapter 1 Overview
b INPUT SELECT section
c MENU button
d COUNTER SEL button
e RESET (NO) button
MIX
A
B
f SET (YES) button
MARK
g
buttons
h TC PRESET button
i SC PHASE control
j SYNC PHASE control
a MONITOR SELECT switches
Use these switches to select the channels for audio output
via the AUDIO MONITOR OUT connector on the rear
panel and the HEADPHONES connector on the front
panel.
Use the left switch to select the basic channel setting, then
use the right switch to select the output format (monaural,
stereo, or mix).
The following table lists the correspondence of left/right
switch settings and channel/output format selections.
Switch setting
Selected channel and output
format
Left
switch
HEADPHONES AUDIO
connector
MONITOR OUT
connector
Right
switch
CH1/3
CH2/4
Channel 1 only
(monaural)
CH2/4
Channels 1 and Channels 1 and
2 (stereo)
2 (mix)
CH2/4
Channel 2 only
(monaural)
Channel 2 only
(monaural)
CH2/4
Channel 3 only
(monaural)
Channel 3 only
(monaural)
CH2/4
Channels 3 and Channels 3 and
4 (stereo)
4 (mix)
CH2/4
Channel 4 only
(monaural)
MIX
CH1/2
CH3/4
CH1/3
MIX
CH1/3
MIX
CH1/3
MIX
CH1/2
CH3/4
CH1/3
MIX
CH1/3
MIX
10
Location and Function of Parts
Channel 1 only
(monaural)
Channel 4 only
(monaural)
b INPUT SELECT section
CH1,1/2 (audio channel 1 or 1/2) button
Each press of this button cycles through the following
input audio signal selection options for audio channel 1
(when in 2-channel mode) or for audio channels 1 and 2
(when in 4-channel mode).
• Analog audio signal(s) input to the AUDIO IN CH-1
connector (when in 2-channel mode) or AUDIO IN CH1 and CH-2 connectors (when in 4-channel mode)
• Digital audio signal in AES/EBU format input to the
DIGITAL AUDIO (AES/EBU) IN CH-1/2 connector
(optional DSBK-1801 board required)
• SDI audio signal input to the SDI IN connector (optional
DSBK-1801 board required)
• Audio test signal (selected with the INT AUDIO SG
menu item (see page 65) generated by the internal signal
generator
In the input selection/audio mode display section, the
AUDIO CH1 1/2 display shows the selection made with
this button.
CH2,3/4 (audio channel 2 or 3/4) button
Each press of this button cycles through the input audio
signal selection options for audio channel 2 (when in 2channel mode) or for audio channels 3 and 4 (when in 4channel mode). The input audio signal selection options
corresponding to those for the CH1,1/2 button described
above are available.
In the input selection/audio mode display section, the
AUDIO CH2 3/4 display shows the selection made with
this button.
SDTI/i.LINK (SDTI(QSDI) interface/i.LINK selection)
button
Each press of this button cycles through the following
input signal selection options.
• Digital video signal in SDTI(QSDI) format input to the
SDTI(QSDI) IN connector (optional DSBK-1802 board
required)
c MENU button
Press this button to display the menu on the monitor screen
and the time counter display. Press it again to return from
the menu display to the usual display.
Chapter 1 Overview
VIDEO IN button
Each press of this button cycles through the following
input video signal selection options.
• Composite video signal input to the VIDEO IN
connectors
• Component video signals input to the COMPONENT
VIDEO IN connectors
• S-video signal input to the S VIDEO IN connector
• SDI video signal input to the SDI IN connector (optional
DSBK-1801 board required)
• Video test signal (selected with the INT VIDEO SG
menu item (see page 62) generated by the internal signal
generator
In the input selection/audio mode display section, the
VIDEO display shows the selection made with this button.
When this is selected, use the CH1,1/2 button and
CH2,3/4 button to select the required input audio signals.
• Digital video and audio signals in SDTI(QSDI) format
input to the SDTI(QSDI) IN connector (optional DSBK1802 board required)
• Digital video and audio signals in i.LINK-compatible
DV format, input to the DV IN/OUT connector
(optional DSBK-1803 board required)
In the input selection/audio mode display section, the
INPUT display shows the selection made with this button.
On how to use the menu, see Chapter 4 “Menu Settings.”
d COUNTER SEL (selection) button
Selects the type of time data to be shown in the time
counter display. Each press of this button cycles through
three indicator display options: COUNTER (CNT: count
value of the time counter), TC (time code), and U-BIT
(user bits).
Note
When the REMOTE button in the remote control setting
section is lit, the COUNTER SEL button does not operate.
In this case, make the time data selection via the remote
equipment that is connected to the REMOTE connector on
the rear panel.
e RESET (NO) button
Press this button to:
• reset menu settings,
• reset the time count (COUNTER) shown in the time
counter display to zero, or
• send a negative response to the prompts issued by the
unit.
f SET (YES) button
Press this button to:
• save new settings, such as selected menu items and time
code settings, to the memory of the unit, or
• send a positive response to the prompts issued by the
unit.
g Arrow (JjKk) buttons
Use these buttons to move around the menu items, and also
for setting time code and user bit data.
For details on setting time code and user bit data, see
“Using the Internal Time Code Generator” on page 43.
Location and Function of Parts
11
h TC (time code) PRESET button
Use this button when setting an initial time code value and
user bit data.
respect to the reference video signal. Use a cross-point
(Phillips) screwdriver to turn it.
For details on setting time code and user bit data, see
“Using the Internal Time Code Generator” on page 43.
j SYNC (synchronization) PHASE control
Turn this control to accurately adjust the synchronization
phase of the output video signal of the unit with respect to
the reference video signal. Use a cross-point (Phillips)
screwdriver to turn it.
Chapter 1 Overview
i SC (subcarrier) PHASE control
Turn this control to accurately adjust the subcarrier phase
of the composite video output signal of the unit with
C Tape transport control section
a EJECT button
b REW button
c REC button
f STOP button
e F FWD button
d PLAY button
a EJECT button
When you press this button, it lights and the cassette is
automatically ejected after a few seconds.
b REW (rewind) button
When you press this button, it lights and the tape starts
rewinding (maximum 85 times normal speed).
When the F. FWD/REW menu item (see page 57) is set to
PB, you can monitor the playback picture during the
rewind.
c REC (record) button
When you press this button while holding down the PLAY
button, it lights and recording begins.
d PLAY button
When you press this button, it lights and playback begins.
If you press this button during recording or editing, the
recording or editing operation is stopped and this unit
enters playback mode.
12
Location and Function of Parts
e F FWD (fast forward) button
When you press this button, it lights and the tape is fast
forwarded (maximum 85 times normal speed).
When the F. FWD/REW menu item (see page 57) is set to
PB, you can monitor the playback picture during the fast
forward.
f STOP button
Press this button to stop the current tape transport
operation.
Note
No tape transport control buttons other than the EJECT
and STOP buttons will work while the REMOTE button in
the remote control setting section is lit. This can be
changed with the LOCAL ENABLE menu item (see page
57).
D Display section
a Recording/playback format indicators
b ClipLink indicator
c VITC indicator
Chapter 1 Overview
d Time data type indicators
e Time counter display
i CHANNEL CONDITION indicators
h SERVO indicator
g Cassette memory indicator
f REC INHIBIT indicator
j REPEAT indicator
k Tape end alarm indicator
l SHUTTLE/JOG indicators
m NOT EDITABLE indicator
a Recording/playback format indicators
DVCAM: This lights when a tape recorded in DVCAM
format is played back.
DV: This lights when a tape recorded in consumer DV
format is played back.
LP: This lights when a tape recorded in LP mode is played
back.
When a tape recorded in DVCPRO (25M) format or any
other format than those mentioned above is played back,
none of the above indicators lights.
Note
A tape recorded in LP mode cannot be played back
correctly. When a tape recorded in LP mode is played
back, “DV LP” flashes and audio is muted.
b ClipLink indicator
Lights when a cassette is loaded on which ClipLink log
data is stored in the cassette memory.
For details of ClipLink log data, see the appendix
“ClipLink Guide” (page 104).
Location and Function of Parts
13
c VITC indicator
Lights when VITC is being read or recorded regardless of
the data shown in the time counter display.
Chapter 1 Overview
d Time data type indicators
One of the three indicators (COUNTER, U-BIT, and TC)
lights to indicate the type of time data currently shown in
the time counter display.
COUNTER: Count value of the time counter
U-BIT: User bit data
TC: SMPTE time code (for DSR-1800) or EBU time code
(for DSR-1800P)
e Time counter display
Indicates the count value of the time counter, time code,
VITC, or user bit data depending on the settings of the
COUNTER SEL button on the menu control panel and the
TC SELECT menu item (see page 61).
Also used to display error messages and setup menu data.
f REC (recording) INHIBIT indicator
Lights in the following cases:
• The REC/SAVE switch on the loaded cassette is in the
SAVE position.
• The REC INHIBIT menu item (see page 57) is set to
ON.
l SHUTTLE/JOG indicators
When searching in shuttle mode using the search dial, the
SHUTTLE indicator lights, and when searching in jog
mode using the search dial, the JOG indicator lights. When
the search dial is turned clockwise causing playback to
take place in the forward direction, the G indicator lights.
When the search dial is turned counterclockwise causing
playback to take place in the reverse direction, the g
indicator lights. When the tape is stopped, the s indicator
lights.
For more information about the search dial, see “Search
dial” in the next section.
m NOT EDITABLE indicator
Lights during playback of a tape that contains a recording
in other than the DVCAM format. When this indicator is
lit, the recordings contained in the tape can be used as
source material for editing, but editing operations such as
insert editing and assemble editing cannot be performed.
This indicator also lights when the audio recording mode
selected on this unit does not coincide with that of the
loaded tape.
E Search control section
g Cassette memory indicator
Lights when a cassette provided with a memory chip
(“cassette memory”) is loaded.
h SERVO indicator
This indicator lights when the drum servo and capstan
servo are locked*.
* Servo lock: This refers to the synchronization of the phase of the drum
rotation and the reference signal for the tape transport position, so that the
video heads can trace the same pattern on the tape for playback and
recording.
i CHANNEL CONDITION indicators
These three-color indicators show the state of the playback
signal.
Green: The state of the playback signal is good.
Yellow: The playback signal is somewhat deteriorated, but
playback is possible.
Red: The playback signal is deteriorated. When the red
indicator remains on, head cleaning or an internal
inspection is necessary.
j REPEAT indicator
This indicator lights when the REPEAT MODE menu item
(see page 56) is set to ON.
k Tape end alarm indicator
Starts flashing when the remaining capacity of the tape is
for about 2 minutes.
14
Location and Function of Parts
b Search dial
a SEARCH button
a SEARCH button
To use the search dial for playback in shuttle or jog mode,
press this button, turning it on. Pressing the dial toggles
between shuttle and jog modes. In shuttle mode, the
SHUTTLE indicator in the display section lights, and in
jog mode, the JOG indicator in the display section lights.
b Search dial
Turn this to carry out playback in the modes shown in the
following table. Turning the dial clockwise lights the G
indicator in the display section and plays back in the
forward direction. Turning the dial counterclockwise
lights the g indicator in the display section and plays back
in the reverse direction. When the tape is stopped, the s
indicator in the display section lights.
Pressing this dial toggles playback between shuttle mode
and jog mode. When playing back in shuttle mode, the
SHUTTLE indicator in the display section lights, and
when playing back in jog mode, the JOG indicator lights.
You can carry out noiseless playback in the range of ±1/2
times normal speed.
Playback mode
Operation and functions
Shuttle
Press the SEARCH button or the search
dial so that the SHUTTLE indicator in
the display section lights, then turn the
search dial.
Playback is carried out at a speed
determined by the position of the search
dial. The maximum shuttle mode
playback speed can be changed with the
SHUTTLE menu item (see page 57).
Jog
Press the SEARCH button or the search
dial so that the JOG indicator in the
display section lights, then turn the
search dial. Playback is carried out at a
speed determined by the speed of
rotation of the search dial. The playback
speed is up to ±1 times normal speed by
factory default.
The search dial has no detents.
c i.LINK button
When carrying out remote control between this unit and
the unit connected to the DV IN/OUT connector, press
this button, turning it on. This requires the optional DSBK1803 board to be installed.
Chapter 1 Overview
Playback modes using the search dial
b 9PIN button
When carrying out remote control between this unit and
the unit connected to the REMOTE connector, press this
button, turning it on.
You can use the SEARCH ENABLE menu item (see page
57) to select either of the following as the operation to be
performed to put the unit into search mode (shuttle or jog).
• Either press the SEARCH button or, except during
recording/editing, turn the search dial (factory default
setting).
• Press the SEARCH button.
F Remote control setting section
a REMOTE button
b 9PIN button
c i.LINK button
a REMOTE button
When remote-controlling this unit from the unit connected
to the REMOTE connector or DV IN/OUT connector,
press this button, turning it on.
When reverting to local mode to use the buttons in the tape
transport control section, press this button again, turning it
off.
Location and Function of Parts
15
Rear Panel
A Analog video signal input/output section (see page 17)
Chapter 1 Overview
B Digital signal input/output section (see page 18)
IN
ANALOG VIDEO
VIDEO IN
LOW
OFF
LEVEL
DIGITAL AUDIO(AES/EBU)
OUT
IN
OUT
IN CH-1/2
CH-3/4
OUT CH-1/2 CH-3/4
TIME CODE
S VIDEO
IN
AUDIO IN
SDI
SDTI(QSDI)
DV IN/OUT
HIGH LOW
ON OFF
600Ω
LEVEL
COMPONENT VIDEO IN
Y
HIGH LOW
ON OFF
600Ω
R-Y
LEVEL
REF.VIDEO
IN
B-Y
HIGH LOW
ON OFF
600Ω
LEVEL
HIGH
ON
600Ω
VIDEO OUT
OUT
1
2
(SUPER)
S VIDEO COMPONENT VIDEO OUT
OUT
Y
R-Y
IN
B-Y
OUT
VIDEO CONTROL
MONITOR OUT
AUDIO OUT
AUDIO
REMOTE
CH-1
CH-2
CH-3
CH-4
CH-1
CH-2
CH-3
CH-4
~AC IN
D External device connectors (see page 20)
C Analog audio signal input/output section (see page 19)
AC IN connector
Use the supplied power cord to connect this to an AC
outlet.
16
Location and Function of Parts
AC IN connector
A Analog video signal input/output section
ANALOG VIDEO
VIDEO IN
S VIDEO
IN
COMPONENT VIDEO IN
Y
R-Y
REF.VIDEO
IN
B-Y
VIDEO OUT
OUT
1
2
(SUPER)
S VIDEO
OUT
Y
d REF. VIDEO IN/OUT connectors
Chapter 1 Overview
e VIDEO OUT 1 and 2 (SUPER)
connectors
c COMPONENT VIDEO IN Y/R−Y/B−Y connectors
b S VIDEO IN connector
a VIDEO IN connectors
TIME CODE
VIDEO OUT
2
S VIDEO COMPONENT VIDEO OUT
OUT
Y
R-Y
B-Y
IN
OUT
h TIME CODE IN/OUT connectors
g COMPONENT VIDEO OUT Y/R−Y/B−Y connectors
f S VIDEO OUT connector
a VIDEO IN connectors (BNC type)
Input an analog composite video signal. This connector
block has a built-in automatic 75 Ω termination switch.
When a signal is input to the left VIDEO IN connector
with no bridging (loop-through) connection made, the
connector is terminated with an impedance of 75 Ω
automatically. To connect the signal input to the left
VIDEO IN connector also to other equipment, use the right
VIDEO IN connector (marked
). When the right
VIDEO IN connector is used, the built-in 75 Ω termination
switch turns off automatically.
b S VIDEO IN connector (4-pin)
Input an S-video signal with separated Y (luminance) and
C (chroma: 3.58 MHz for DSR-1800 or 4.43 MHz for
DSR-1800P) components to this connector.
c COMPONENT VIDEO IN Y/R−Y/B−Y connectors
(BNC type)
Input analog component video signals (Y/R−Y/B−Y) to
these connectors.
d REF. (reference) VIDEO IN/OUT connectors
(BNC type)
Input a reference video signal. The IN connector block has
a built-in automatic 75 Ω termination switch. When a
signal is input to the left REF. VIDEO IN connector with
no bridging (loop-through) connection made, the
connector is terminated with an impedance of 75 Ω
automatically. To connect the reference video signal input
to the left REF. VIDEO IN connector also to other
equipment, use the right REF. VIDEO IN connector
(marked
). When the right REF. VIDEO IN connector
Location and Function of Parts
17
is used, the built-in 75 Ω termination switch turns off
automatically.
The REF. VIDEO OUT connector outputs a reference
video signal, except when i.LINK is selected in the INPUT
SELECT section (see page 11).
g COMPONENT VIDEO OUT Y/R−Y/B−Y
connectors (BNC type)
These connectors output analog component video signals
(Y/R−Y/B−Y).
Chapter 1 Overview
h TIME CODE IN/OUT connectors (BNC type)
Input SMPTE time code (for DSR-1800) or EBU time
code (for DSR-1800P) externally generated to the IN
connector.
The OUT connector outputs a time code according to the
operating state of the unit, as follows:
During playback: the playback time code
During recording: the time code generated by the internal
time code generator or the time code input to the TIME
CODE IN connector. When the EE OUT PHASE menu
item (see page 61) is set to MUTE, no time code is output.
e VIDEO OUT 1 and 2 (SUPER) connectors (BNC
type)
These connectors output analog composite video signals.
When the CHARA. DISPLAY menu item (see page 59) is
set to ON (factory default setting), connector 2 (SUPER)
outputs a signal with superimposed text information.
f S VIDEO OUT connector (4-pin)
This connector outputs an S-video signal with separated Y
(luminance) and C (chroma: 3.58 MHz for DSR-1800 or
4.43 MHz for DSR-1800P) components.
B Digital signal input/output section (optional DSBK-1801/1802/1803 boards required)
DV IN/OUT
a
DV IN/OUT connector
SDTI(QSDI)
IN
OUT
b SDTI (QSDI) IN/OUT connectors
SDI
IN
OUT
DIGITAL AUDIO(AES/EBU)
IN CH-1/2
CH-3/4
OUT CH-1/2 CH-3/4
f DIGITAL AUDIO (AES/EBU) OUT connectors
e DIGITAL AUDIO (AES/EBU) IN connectors
d SDI OUT connectors
c SDI IN and active through output connectors
18
Location and Function of Parts
a
DV IN/OUT connector (6-pin IEEE-1394)
(optional DSBK-1803 i.LINK/DV Input/Output
Board required)
This i.LINK-compatible connector (subsequently referred
to also as the i.DV IN/OUT connector) inputs and outputs
digital video and audio signals in DV format.
c SDI (Serial Digital Interface) IN (input) and active
through output connectors (BNC type) (optional
DSBK-1801 SDI/AES/EBU Input/Output Board
required)
Input digital video and audio signals in SDI format to the
left-hand connector. The right-hand connector is for an
active-through connection.
Note
d SDI (Serial Digital Interface) OUT connectors
(BNC type) (optional DSBK-1801 SDI/AES/EBU
Input/Output Board required)
Output SDI-format digital video and audio signals. The
same signals are output from both connectors.
b SDTI (QSDI) (Serial Data Transport Interface
(QSDI)) IN/OUT connectors (BNC type) (optional
DSBK-1802 SDTI (QSDI) Input/Output Board
required)
The IN connector inputs and the OUT connector outputs
digital video and audio signals in SDTI (QSDI) format.
e DIGITAL AUDIO (AES/EBU) IN connectors
(BNC type) (optional DSBK-1801 SDI/AES/EBU
Input/Output Board required)
Input digital audio signals in AES/EBU format to these
connectors.
The left-hand connector (CH-1/2) is for audio channels 1
and 2, and the right-hand connector (CH-3/4) is for audio
channels 3 and 4.
Note
When searching at speeds in the range +1/2 to +1/30 or
−1/2 to −1/30 times normal speed, the audio signal output
from this connector and monitored on external equipment
may sound differently from the audio signal played back
on this unit.
Chapter 1 Overview
When searching at speeds in the range +1/2 to +1/30 or
−1/2 to −1/30 times normal speed, the audio signal output
from this connector and monitored on external equipment
may sound differently from the audio signal played back
on this unit.
f DIGITAL AUDIO (AES/EBU) OUT connectors
(BNC type) (optional DSBK-1801 SDI/AES/EBU
Input/Output Board required)
These connectors output digital audio signals in AES/EBU
format.
The left-hand connector (CH-1/2) is for audio channels 1
and 2, and the right-hand connector (CH-3/4) is for audio
channels 3 and 4.
C Analog audio signal input/output section
a AUDIO IN LEVEL/600 Ω switches
AUDIO IN
LOW
OFF
LEVEL
HIGH LOW
ON OFF
600Ω
LEVEL
HIGH LOW
ON OFF
600Ω
LEVEL
HIGH LOW
ON OFF
600Ω
LEVEL
HIGH
ON
600Ω
c AUDIO OUT CH-1 to CH-4 connectors
MONITOR OUT
AUDIO OUT
AUDIO
CH-1
CH-2
CH-3
CH-4
b AUDIO IN CH-1 to CH-4 connectors
CH-1
CH-2
CH-3
CH-4
d AUDIO MONITOR OUT connector
a AUDIO IN LEVEL/600 Ω switches
Set these switches for each channel as shown in the
following table, according to the audio input levels to the
AUDIO IN CH-1 to CH-4 connectors and the required
impedance.
Location and Function of Parts
19
Settings of the AUDIO IN LEVEL/600 Ω switches
Audio input
Switch setting
VIDEO CONTROL
Chapter 1 Overview
Level
Impedance
−60 dBu
(microphone input)
High impedance
(about 20 kΩ)
LOW-OFF
(left position)
+4/0/−3 a)/−
−6 dBu
(line audio input)
High impedance
(about 20 kΩ)
HIGH-OFF
(middle
position)
−6 dBm
+4/0/−3 a)/−
(line audio input)
600 Ω
HIGH-ON
(right position)
a VIDEO CONTROL connector
REMOTE
a) Selectable on DSR-1800P only
b AUDIO IN CH-1 (channel 1) to CH-4 connectors
(XLR 3-pin, female)
Use these connectors to connect separate channels of
analog audio input from a player VCR or other external
audio equipment.
You can switch the audio input level setting with the
LEVEL SELECT menu item (see page 64).
c AUDIO OUT CH-1 (channel 1) to CH-4 connectors
(XLR 3-pin, male)
These connectors output channel-1 to channel-4 analog
audio signals, respectively.
It is possible to use the AUDIO OUT CH-3 and AUDIO
OUT CH-4 connectors for audio monitor output for
channels 1 and 2, respectively (use the OUTPUT CH3/4
menu item (see page 65)).
d AUDIO MONITOR OUT connector (RCA phono
jack)
This connector outputs audio signals for monitoring. The
audio signals to be output from this connector can be
selected with the MONITOR SELECT switches on the
menu control panel.
20
D External device connectors
Location and Function of Parts
b REMOTE connector
a VIDEO CONTROL connector (D-sub 15-pin)
For remote control of the internal digital video processor,
connect an optional remote control unit such as the UVR60/60P or BVR-50/50P to this connector.
b REMOTE connector (D-sub 9-pin)
When controlling this unit from an editing control unit
such as the ES-3, ES-7, PVE-500, BVE-600/800/910/
2000, or RM-450/450CE, connect the unit to the editing
control unit via this connector using the optional 9-pin
remote control cable.
Recording and Playback
Chapter
2
Usable Cassettes
This unit can use the DVCAM cassettes listed below.
Model name
Size
PDV-64ME/94ME/124ME/184ME
Standard size
PDVM-12ME/22ME/32ME/40ME
Mini size
The numbers in each model name indicate the maximum recording/playback
time (in minutes) for each model. For example, the PDV-184ME has a
maximum recording/playback time of 184 minutes.
Cassettes usable for playback only
All consumer DV cassettes and large- and medium-size DVCPRO (25M)
cassettes are usable for playback only.
Notes
• If you insert an incorrect type of cassette, it will be automatically ejected.
• When operating this unit as a player, you can also use DV cassettes on the
unit. However, it is the best choice to always use DVCAM cassettes because
they are more reliable than DV cassettes whatever your purpose may be:
playback, editing, or long-period storage of recordings.
• Cassettes that have been recorded by a DV-format recorder can be played
back on this unit but cannot be used for recording at editing operation. When
you insert such a cassette into this unit, the NOT EDITABLE indicator lights
up in the display section on the front panel of this unit.
Usable Cassettes
21
DVCAM cassettes
The following figure illustrates the DVCAM cassettes.
REC/SAVE switch
For details of this switch, see “Preventing accidental
erasure” on page 23
Mini size
Standard size
Chapter 2 Recording and Playback
Cassette memory
This memory is used to store ClipLink log data.
For details of ClipLink log data, see the appendix
“ClipLink Guide”(page 104).
Notes on using cassettes
• Before storing the cassette for a long period of time, rewind the tape to the
beginning and be sure to put the cassette in its storage case, preferably on end
instead of flat on its side.
Storing a cassette in any other condition (not rewound, out of its case, etc.)
may cause the video and audio contents to become damaged over time.
• If the cassette memory connector (contact point) becomes dirty, connection
problems may occur, causing a loss of functions. Remove away any dust or
dirt from this area before using the cassette.
• If the cassette is dropped on the floor or otherwise receives a hard impact, the
tape may become slackened and may not record and/or play back correctly.
For information about how to check the tape for slack, see the next section.
Checking the tape for slack
Using a paper clip or a similar object, turn the reel gently in the direction shown
by the arrow. If the reel does not move, there is no slack. Insert the cassette into
the cassette compartment, and after about 10 seconds take it out.
Paper clip, etc.
Reel
22
Usable Cassettes
Preventing accidental erasure
Set the REC/SAVE switch on the cassette to SAVE to prevent accidental
erasure of recorded contents.
REC/SAVE switch
Set to SAVE
REC
SAVE
Inserting and Ejecting Cassettes
Inserting a cassette
This unit accepts three sizes of cassette: L (standard size), M (medium size:
DVCPRO) and S (mini size). When inserting a cassette in the unit, make sure
its tape window faces upward as shown in the following figure.
Outer guides
Chapter 2 Recording and Playback
To enable re-recording
Set the REC/SAVE switch to REC.
When this switch is set to SAVE, the unit cannot record on the tape.
Mini size (Insert the cassette into the
middle of the cassette compartment.)
Standard size
Tape window facing upward
Inner guides
Medium size (Align the cassette with
the outer guides, then slide it in over
the inner guides.)
Tape window facing upward
Usable Cassettes
23
No double insertion of cassettes
When you insert a cassette, the orange lock-out plate appears in the cassette
compartment to prevent double insertion.
Ejecting a cassette
Press the EJECT button.
dB
0
-12
-20
-30
-40
-60
Chapter 2 Recording and Playback
24
OVER
dB
0
dB
0
1
-12
0
-20
-1
-2
-30
-40
1
-60
OVER
dB
0
dB
0
1
-12
0
-20
-1
-2
-30
-40
2
-60
OVER
dB
0
dB
0
1
-12
0
-20
-1
-2
-30
-40
3
-60
OVER
dB
INPUT
V:SDTI
SDTI
i.LINK
0
1
VIDEO
0
CH11/2
-1
AUDIO
-2
4
CH23/4
PB FS
COMPOSITE Y-R,B S VIDEO
ANALOG AES/EBU
ANALOG AES/EBU
48k44.1k32k REC MODE
SDI
SG
SDI
SG
SDI
SG
2CH4CH
EJECT button
Usable Cassettes
Recording
This section describes the necessary settings and operations to perform
recording on this unit. The same settings and operations apply whether you are
using the unit as part of an editing system, for dubbing*, or as a stand-alone
recorder.
* For dubbing of SDTI (QSDI) format signals, use the AUTO FUNCTION menu item SDTI (QSDI)
DUBBING (see page 69). For details, see “Digitally Dubbing Signals in DVCAM Format” on page
50.
For the necessary connections for recording and the settings not covered in this
section, see Chapter 5 “Connections and Settings.”
Player (DSR-1600/1600P, etc.)
dB
0
OVER
dB
0
-12
-20
-60
dB
0
1
-12
0
-20
-1
-30
-40
-2
-30
-40
1
-60
OVER
dB
0
dB
0
1
-12
0
-20
-1
-2
-30
-40
2
-60
OVER
dB
0
dB
0
1
-12
0
-20
-1
-2
-30
-40
3
-60
OVER
dB
0
1
0
-1
-2
48k44.1k32k
PB FS
4
2
1
Chapter 2 Recording and Playback
Settings for Recording
Video monitor
Audio level meters
Input selection/audio mode
display section
3
dB
0
-12
-20
-30
-40
-60
OVER
dB
0
dB
0
1
-12
0
-20
-1
-2
-30
-40
1
-60
OVER
dB
0
dB
0
1
-12
0
-20
-1
-2
-30
-40
2
-60
OVER
dB
0
dB
0
1
-12
0
-20
-1
-2
-30
-40
3
-60
OVER
dB
INPUT
V:SDTI
SDTI
REMOTE button
i.LINK
0
1
VIDEO
0
CH11/2
-1
AUDIO
-2
4
CH23/4
PB FS
COMPOSITE Y-R,B S VIDEO
ANALOG AES/EBU
ANALOG AES/EBU
48k44.1k32k REC MODE
SDI
SG
SDI
SG
SDI
SG
2CH4CH
7
Recorder (DSR-1800/1800P)
A
B
MARK
5
6
4
Note
When controlling this unit from an editing control unit connected to the
REMOTE connector, see “Remote control setting section” (page 15).
Recording
25
1
Power on the video monitor, then set its input switches according to the
signals input from this unit.
2
Set up the player to play back a tape.
For details, refer to the operating instructions for the player.
3
Power on this unit by pressing on the
4
When the REMOTE button is not lit (the external editing control unit is not
used), use the COUNTER SEL button to select the type of time data to be
used.
side of the POWER switch.
Each press of this button cycles through three options: COUNTER (CNT
value), TC (time code), and U-BIT (user bit data). The time data type
indicator for each option lights as it is selected.
Chapter 2 Recording and Playback
Selected time data
Time data type indicator
Count value of the time counter
COUNTER
Time code
TC
User bit data
U-BIT
When the REMOTE button is lit, selection of the time data type is carried
out at the editing control unit.
5
Select the formats of video and audio input signal to be recorded.
Use the buttons in the INPUT SELECT section to select the desired signal
formats. Each selection is shown by a lit indicator in the input selection/
audio mode display section.
Video input signal
(input connector)
Corresponding button
in the INPUT SELECT
section
Lit indicator in the
input selection/audio
mode display section
Composite signal
(VIDEO IN)
VIDEO IN
COMPOSITE in VIDEO
group
Separated Y/C signal
(S VIDEO IN)
VIDEO IN
S VIDEO in VIDEO
group
Component signal
(COMPONENT VIDEO
IN)
VIDEO IN
Y−R, B in VIDEO group
SDI signal (SDI IN)
VIDEO IN
SDI a) in VIDEO group
SDTI (QSDI) signal
(SDTI (QSDI) IN)
SDTI/i.LINK
SDTI a): both SDTI video
and audio input
signals are
recorded.
V:SDTI a): only SDTI
video input signal is
recorded.
i.LINK-compatible digital SDTI/i.LINK
video signal in DV format
(i.DV IN/OUT)
i.LINK a)
Internal test video signal VIDEO IN
SG in VIDEO group
a) The indicator does not light even if you press the corresponding button in the INPUT SELECT
section unless the required optional digital input/output board (DSBK-1801/1802/1803) is
installed.
26
Recording
Audio input signal
(input connector)
Corresponding button
in the INPUT SELECT
section
Lit indicator in the
input selection/audio
mode display section
Analog signal
(AUDIO IN CH-1 to CH4)
CH-1,1/2 and CH-2,3/4
ANALOG in AUDIO
group
AES/EBU signal
(DIGITAL AUDIO (AES/
EBU) IN)
CH-1,1/2 and CH-2,3/4
AES/EBU a) in AUDIO
group
SDI signal (SDI IN)
CH-1,1/2 and CH-2,3/4
SDI a) in AUDIO group
SDTI (QSDI) signal
(SDTI (QSDI) IN)
SDTI/i.LINK
SDTI a)
i.LINK a)
Internal test audio signal CH-1,1/2 and CH-2,3/4
SG in AUDIO group
a) The indicator does not light even if you press the corresponding button in the INPUT SELECT
section unless the required optional digital input/output board (DSBK-1801/1802/1803) is
installed.
Caution
Once you have started recording, you cannot change the input signal
selection.
6
Select the audio mode.
Select either two-channel mode (2CHANNEL) or four-channel mode
(4CHANNEL) with the REC MODE menu item (see page 63). The
corresponding indicator lights in the REC MODE display.
Audio mode
Lit indicator in the REC MODE display
2-channel mode
2CH
4-channel mode
4CH
Chapter 2 Recording and Playback
i.LINK-compatible digital SDTI/i.LINK
audio signal in DV format
(i.DV IN/OUT)
Cautions
• In the DVCAM format, there are two audio recording modes, with either
two channels at 48 kHz or four channels at 32 kHz. It is not possible to
select other modes (for example with four channels at 48 kHz).
• During audio editing, if a signal used in assemble or insert editing is in a
different mode from the base tape, the signals will be discontinuous at the
edit points, and correct editing will not be obtained. For this reason, audio
editing between different modes is inhibited on this unit.
For smooth editing operations, check the audio recording mode of the
base tape beforehand.
• Once you have started recording, you cannot change the audio mode
selection.
• If on a tape there is a point where the audio mode is switched, it is not
possible to carry out insert editing over a section including that point.
7
Use the AUDIO INPUT LEVEL control knobs to adjust audio input levels.
Watching the audio level meter, adjust the level so that the meter does not
indicate higher values than 0 dB when the audio signal is at its maximum.
When the level exceeds 0 dB, the OVER indicator lights.
The factory-preset audio recording level is −20 dB (DSR-1800) or −18 dB
(DSR-1800P). This setting can be changed using the LEVEL SELECT
menu item (see page 64).
Recording
27
Recording Procedure
This section describes the procedure to perform recording on this unit, showing
an example session in which playback signals coming from a player VCR will
be recorded on the tape loaded in the unit.
1
dB
0
OVER
dB
-20
-30
-40
-60
dB
0
0
-12
1
-12
0
-20
-1
-2
-30
-40
1
-60
OVER
dB
dB
0
0
1
-12
0
-20
-1
-2
-30
-40
2
-60
OVER
dB
dB
0
0
1
-12
0
-20
-1
-2
-30
-40
3
-60
OVER
dB
INPUT
V:SDTI
SDTI
i.LINK
0
VIDEO
1
0
CH11/2
-1
AUDIO
CH23/4
-2
PB FS
4
COMPOSITE Y-R,B S VIDEO
ANALOG AES/EBU
ANALOG AES/EBU
48k44.1k32k REC MODE
SDI
SG
SDI
SG
SDI
SG
2CH4CH
REMOTE button
Chapter 2 Recording and Playback
Recorder
(DSR-1800/1800P)
dB
0
-12
-20
-30
-40
-60
OVER
dB
0
dB
0
1
-12
0
-20
-1
-2
-30
-40
1
-60
OVER
dB
0
dB
0
1
-12
0
-20
-1
-2
-30
-40
2
-60
OVER
dB
0
dB
0
1
-12
0
-20
-1
-2
-30
-40
3
-60
OVER
2
dB
0
1
0
-1
-2
4
PB FS
48k44.1k32k
Player
(DSR-1600/1600P, etc.)
3
Notes
• When controlling this unit from an editing control unit connected to the
REMOTE connector of this unit, press the REMOTE button to turn it on.
When not, turn off the button.
• If you intend to use a tape recorded on this unit in a system comprising a DSR85/85P and an ES-7 EditStation, it is recommended to record color bars on at
least the first 40 seconds of the tape.
When transferring digital signals from the DSR-85/85P to the ES-7
EditStation at four times normal speed, there must be recording for
approximately 40 seconds before the IN point.
28
Recording
1
After checking the following items, hold the cassette with the tape window
facing upward, then insert it into the recorder (this unit) as illustrated on
page 23.
.
Item to check
See section
Make sure that the REC/SAVE switch “Preventing accidental erasure” on
of the cassette is set to REC.
page 23
Check for tape slack.
“Checking the tape for slack” on page
22
Make sure that the “HUMID!” alarm is “Condensation” on page 91
not shown in the time counter display.
The cassette is automatically drawn into the unit and the tape is wound
round the head drum. The tape is stationary while the head drum rotates, and
the STOP button lights.
Note
When ejecting and loading cassettes, make sure that the unit has been
powered on.
2
Hold down the REC button and press the PLAY button.
Chapter 2 Recording and Playback
If the REC INHIBIT indicator lights:
It indicates that the REC/SAVE switch of the loaded cassette has been set
to SAVE. Press the EJECT button in the tape transport control section to
remove the cassette, then set the REC/SAVE switch to REC and reload the
cassette.
This puts the unit into recording mode, and the tape starts moving.
3
Press the PLAY button on the player.
The player starts the playback operation, at which point this unit starts
recording the input playback signals.
Cautions
• Once you have started recording, you cannot change the audio mode
selection.
• If on a tape there is a point where the audio mode is switched, it is not
possible to carry out insert editing over a section including that point.
Recording
29
If the following indicators light when a cassette is loaded
Indicator
It means:
Cassette memory indicator The loaded cassette contains a cassette memory.
ClipLink indicator
There is ClipLink log data stored in the cassette
memory on the loaded cassette.
Caution
With such a cassette, carrying out recording destroys
the ClipLink log data.
NOT EDITABLE indicator
The recording format of the tape is “DV,” or a
DVCPRO tape is inserted.
Replace the tape with one that has been recorded in
DVCAM format.
Chapter 2 Recording and Playback
The audio recording mode selected on this unit does
not coincides with that of the tape.
• When your current purpose is recording, you can
use the tape as it is.
• When your current purpose is editing, set the unit
for the same audio recording mode as with the
tape.
For more details, see “Troubleshooting” on page
94.
To perform the following operations
Operation
Do this:
Stop recording.
Press the STOP button.
The unit enters stop mode, and will automatically
switch to standby off mode after the time period set
with the STOP TIMER menu item (see page 62).
Remove the cassette.
Press the EJECT button.
After a few seconds, the tape is unwound from the
head drum and the cassette is automatically ejected.
If a CNT value is shown on the time counter display
(assuming the time data type indicator “COUNTER”
is lit), the CNT value is reset.
Inhibit the unit from
Set the CHARA. DISPLAY menu item (see page 59)
outputting text information to OFF.
(time data, operation mode
indications, etc.) to the
video monitor.
Change the time period
before the unit switches
from stop mode to standby
off mode.
30
Recording
Change the setting of the STOP TIMER menu item
(see page 62).
Playback
This section describes the settings and operations necessary to perform playback
on this unit. The same settings and operations apply whether you are using the
unit as part of an editing system, for dubbing, or as a stand-alone player VCR.
For the necessary connections for playback and the settings not covered in this
section, see Chapter 5 “Connections and Settings.”
Settings for Playback
Chapter 2 Recording and Playback
Video monitor
2
Player (DSR-1800/1800P)
1
dB
0
-12
-20
-30
-40
-60
OVER
dB
0
dB
0
1
-12
0
-20
-1
-2
-30
-40
1
-60
OVER
dB
0
dB
0
1
-12
0
-20
-1
-2
-30
-40
2
-60
OVER
dB
0
dB
0
1
-12
0
-20
-1
-2
-30
-40
3
-60
OVER
dB
INPUT
V:SDTI
SDTI
i.LINK
0
1
VIDEO
0
CH11/2
-1
AUDIO
-2
4
CH23/4
PB FS
COMPOSITE Y-R,B S VIDEO
ANALOG AES/EBU
ANALOG AES/EBU
48k44.1k32k REC MODE
SDI
SG
SDI
SG
SDI
SG
2CH4CH
1
Power on this unit by pressing on the
2
Power on the video monitor and set its switches as shown below.
side of the POWER switch.
Switch
Setting
75 Ω termination switch
ON (or attach a 75 Ω terminator.)
Input switch
Set according to the type of input signal from this
unit.
Playback
31
Playback Procedure
1
dB
0
-12
-20
-30
-40
-60
OVER
dB
0
dB
0
1
-12
0
-20
-1
-2
-30
-40
1
-60
OVER
dB
0
dB
0
1
-12
0
-20
-1
-2
-30
-40
2
-60
OVER
dB
0
dB
0
1
-12
0
-20
-1
-2
-30
-40
3
-60
OVER
dB
INPUT
V:SDTI
SDTI
i.LINK
0
1
VIDEO
0
CH11/2
-1
AUDIO
-2
4
CH23/4
PB FS
COMPOSITE Y-R,B S VIDEO
ANALOG AES/EBU
ANALOG AES/EBU
48k44.1k32k REC MODE
SDI
SG
SDI
SG
SDI
SG
2CH4CH
REMOTE button
2
Chapter 2 Recording and Playback
Note
When controlling this unit from an editing control unit connected to the
REMOTE connector of this unit, press the REMOTE button turning it on. When
not, turn off the button.
1
Insert a cassette.
For details of cassette insertion see page 23, and for usable cassette types
see page 21.
The cassette is automatically drawn into the unit. The STOP button will
light, and a few seconds later a still image will appear on the monitor screen.
2
Press the PLAY button.
This starts the playback operation. When the tape is played back all the way
to the end, the unit automatically rewinds it and then stops.
32
Playback
If the following indicators light when a cassette is loaded
Indicator
It means:
Cassette memory indicator The loaded cassette contains a cassette memory.
ClipLink indicator
There is ClipLink log data stored in the cassette
memory on the loaded cassette.
NOT EDITABLE indicator
The tape was recorded in the DV format, or a
DVCPRO tape is inserted.
You cannot use it as a recording tape for editing.
To perform the following operations
Do this:
Stop playback.
Press the STOP button.
The unit enters stop mode, and will automatically
switch to standby off mode after the time set with the
STOP TIMER menu item (see page 62).
Adjust the audio playback
level.
Use the audio level control on the monitor.
Play back in shuttle mode
while monitoring the video.
Press the SEARCH button or search dial to light the
SHUTTLE indicator in the display section, then rotate
the search dial.
Playback is carried out at the speed determined by
the angular position of the search dial.
The maximum speed for shuttle playback can be
changed using the SHUTTLE menu item (see page
57).
Chapter 2 Recording and Playback
Operation
Play back in jog mode while Press the SEARCH button or search dial to light the
monitoring the video.
JOG indicator in the display section, then rotate the
search dial.
Playback is carried out at the speed according to the
speed of the search dial rotation. The playback
speed range is ±1 times normal speed by factory
default.
The search dial has no detents.
Inhibit the unit from
Set the CHARA. DISPLAY menu item (see page 59)
outputting text information to OFF.
(time data, operation mode
indications, etc.) to the
video monitor.
Remove the cassette.
Press the EJECT button.
If a CNT value is shown on the time counter display,
the CNT value is reset.
Disable the automatic
rewind function.
Set the AUTO REW menu item (see page 58) to
DISABLE.
Change the time period
before the unit switches
from stop mode to standby
off mode.
Change the setting of the STOP TIMER menu item
(see page 62).
Playback
33
Repeat Playback—Automatic Cyclical Playback
Proceed as follows to perform automatic cyclical playback of recording (repeat
playback) between selected start and end points.
1
Set the desired repeat start and end points with the REPEAT FUNCTION
menu item (see page 56).
You can set points A and B as start and end points by following the
procedure described in the next section.
2
Set the REPEAT MODE menu item (see page 56) to ON.
The REPEAT indicator lights.
Chapter 2 Recording and Playback
3
Press the SET (YES) button to save the new setting and close the menu.
4
Press the PLAY button.
The unit repeats playback between the repeat start and end points set in step
1.
Setting Points A and B for Repeat Playback
You can set the repeat playback start point (point A) and end point (point B) by
using the current tape position or inputting time code values.
To perform repeat playback after setting points A and B, press the PLAY button
when the REMOTE button is off. When the DSRM-10 Remote Control Unit is
connected to the CONTROL S connector on the front panel, you can also start
repeat playback by pressing its PLAY button with the REMOTE button of this
unit off.
Setting the current tape position as point A or B
Proceed as follows to set the current tape position as point A or B for repeat
playback.
Buttons used for
setting the current
tape position as
point A
A
B
MARK
Buttons used for setting the
current tape position as
point B
In the following explanation of how to set points A and B for repeat
playback, these three buttons are referred to as the KA button, Bk
button, and SET (YES) MARK button, respectively.
34
Playback
While holding down the SET (YES) MARK button on the menu control panel,
press the KA or Bk button. The time code value of the current tape
position is set as point A or B, and a message “A set” or “B set” is displayed for
0.5 second in the time counter display.
Once set, the point A or B time code value is held in the non-volatile memory
of the unit until changed. It is not lost when the unit is powered off.
Note
When setting point A or B, you can only use a time code value. Even when
COUNTER is selected with the COUNTER SEL button, you cannot use a CNT
value to set point A or B.
Inputting time code values for points A and B
Using the following procedure, you can modify the time code value for point A
or B.
1,15
Chapter 2 Recording and Playback
To check the point A or B time code value
Press the KA or Bk button on the menu control panel. While the button is
held down, the point A or B time code value is displayed on the monitor and in
the time counter display.
If you hold down the KA and Bk buttons simultaneously, the value shown
is the point B time code value minus the point A time code value. If the point A
time code value is greater than the point B time code value, a minus sign (−) is
shown before the value.
8,11 12 2,3,4,6,10,11
A
B
MARK
5,7,9,12 13
1
Press the MENU button.
The following menu display appears.
SYSTEM MENU
SETUP MENU
AUTO FUNCTION
HOURS METER
Setup menu
Time counter display
Monitor screen
Playback
35
2
With “SETUP MENU” selected, press the Bk button.
The display changes as follows.
SETUP MENU
OPERATIONAL FUNCTION
DISPLAY CONTROL
TIME CODE
SETUP BANK OPERATION
MENU GRADE
Operational
Time counter display
:BASIC
Monitor screen
Chapter 2 Recording and Playback
3
With “OPERATIONAL FUNCTION” selected, press the Bk button.
The display changes as follows.
SETUP MENU
OPERATIONAL FUNCTION
REPEAT FUNCTION
AUTO EE SELECT
LOCAL ENABLE :STP&EJ
>REP FUNC
Time counter display
Monitor screen
4
With “REPEAT FUNCTION” selected, press the Bk button.
The contents of the REPEAT FUNCTION menu item are displayed.
SETUP MENU
OPERATIONAL FUNCTION
REPEAT FUNCTION
:OFF
REPEAT MODE
:T.TOP
REPEAT TOP
:V.END
REPEAT END
A PRESET
B PRESET
Monitor screen
36
Playback
>> REPEAT MD
Time counter display
5
Press the j button to select “REPEAT TOP.”
SETUP MENU
OPERATIONAL FUNCTION
REPEAT FUNCTION
REPEAT MODE
:OFF
REPEAT TOP
:T.TOP
REPEAT END
:V.END
A PRESET
B PRESET
>> REP TOP
Time counter display
Monitor screen
6
Press the Bk button.
Chapter 2 Recording and Playback
The display changes as follows.
SETUP MENU
OPERATIONAL FUNCTION
REPEAT FUNCTION
:T.TOP
REPEAT TOP
* TAPE TOP :V.END
A POINT
>>> Tape top
Time counter display
Monitor screen
7
Press the j button to select “A POINT.”
SETUP MENU
OPERATIONAL FUNCTION
REPEAT FUNCTION
REPEAT TOP
:T.TOP
* TAPE TOP :V.END
A POINT
>>> A point
Time counter display
Monitor screen
Playback
37
8
Press the KA button.
The display changes as follows.
SETUP MENU
OPERATIONAL FUNCTION
REPEAT FUNCTION
:OFF
REPEAT MODE
.A
REPEAT TOP
:V.END
REPEAT END
A PRESET
B PRESET
>> REP TOP
Time counter display
Monitor screen
Chapter 2 Recording and Playback
9
Press the j button to select “A PRESET.”
SETUP MENU
OPERATIONAL FUNCTION
REPEAT FUNCTION
:OFF
REPEAT MODE
.A
REPEAT TOP
:V.END
REPEAT END
A PRESET
B PRESET
>> A preset
Time counter display
Monitor screen
10Press the Bk button.
The A PRESET MODE screen appears. The time code value of the current
point A is displayed below the screen title.
A PRESET MODE
A
@00:00:00:00
INC/DEC
SHIFT
CLEAR
DATA SAVE
TO MENU
: ( )( )KEY
: ( )( )KEY
: RESET KEY
:
SET KEY
: MENU KEY
Monitor screen
11Use the KA or Bk button to select the digit in the time code value
display that you want to change.
Each press of the button causes the digit to the left or right to begin flashing.
Holding the button down moves the flashing digit continuously.
If you want to clear the time code value, press the RESET (NO) button. The
value is cleared to 00:00:00:00, and the leftmost digit begins flashing.
38
Playback
12Press the J or j button to increment or decrement the value of the flashing
digit.
Each press of the button increments or decrements the value. Holding the
button down increments or decrements the value continuously. To change
other digits, return to step 11.
13Press the SET (YES)
MARK button to confirm the defined value.
The message “NOW SAVING...” is displayed on the monitor screen and
“Saving...” is shown in the time counter display while the new setting is
being saved in memory.
Caution
The new setting may be lost if you power off the unit during the saving
operation. Wait until the saving operation is completed before powering the
unit off.
After the saving operation is completed, the monitor screen and time
counter display return to the REPEAT FUNCTION setting display as
shown in step 9.
14To set point B, refer to steps 5 to 13. (Select “REPEAT END” in step 5, “B
Chapter 2 Recording and Playback
If you want to discard the changed value
Press the MENU button instead of pressing the SET (YES) MARK button
to return to the menu display, then press the MENU button again to end the
menu operation without saving the changed value into memory.
POINT” in step 7, and “B PRESET” in step 9.)
15Press the MENU button to close the menu.
Cuing Up to Any Desired Position Set as Point A or B
You can set any desired tape position as point A or B and cue up to the set point
when required. To cue up to point A or B, holding down the KA or Bk
button on the menu control panel, press the REW button in the tape transport
control section.
For the methods of setting points A and B, see the previous section.
Playback
39
Chapter 2 Recording and Playback
Playback
40
Convenient Functions
for Editing Operation
Setting the Time Data
This unit is provided with the following functions related
to time data.
• Display and reset CNT value
• Set, display, record, and play back SMPTE/EBU time
code and user bit data
• Set, display, record, and play back VITC
The unit can output the time code read from the tape as an
analog (LTC) signal while in normal-speed playback
mode, and receive an external analog time code (LTC)
signal.
Chapter
3
Use the DISPLAY CONTROL menu items (see page 59)
to select the information displayed and the character type
and position of the indications.
When you set the SUB STATUS menu item (see page 59)
to other than OFF, you can also display supplementary
status information on the monitor screen such as editing
mode settings and the operating mode of the internal time
code generator.
For details of supplementary status information, see
“Displaying Supplementary Status Information” on page
74.
Note
The unit outputs no signal from the TIME CODE OUT
connector unless it is in normal-speed playback mode.
The following explains how to use these functions.
Displaying Time Data and Operation
Mode Indications
Time data and operation mode indications can be
displayed on the monitor screen.
Time data can also be displayed in the time counter display
on this unit.
To view time data and operation mode
indications on the monitor screen
Set the CHARA. DISPLAY menu item (see page 59) to
ON (factory default setting).
The time data and the indication of the current operation
mode are superimposed on the video signal that is being
output from the VIDEO OUT 2 (SUPER) connector, and
can be viewed on the monitor screen.
Setting the Time Data
41
Monitor screen contents
The contents of the monitor screen are shown below.
C Drop frame indication for time code generator
(for DSR-1800 only)
.
Drop frame mode (factory default setting)
:
Non-drop frame mode
A Time data type
Time data
B Drop frame indication
for time code reader a)
C Drop frame indication
for time code
generator a)
D VITC field
indication
0 0 : 0 4 . 4 7 . 0 7 *
T C R
P L A Y
L O C K
E DSR-1800/1800P operation mode
a) This character (.) can appear on the DSR-1800 only. The
character to appear in these two columns is always a colon
( : ) on the DSR-1800P.
Chapter 3 Convenient Functions for Editing Operation
A Time data type
The following time data type indications are displayed.
(blank)
Display fields 1 and 3.
*
Display fields 2 and 4.
E DSR-1800/1800P operation mode
Display
Operation mode
CASSETTE OUT
Cassette is not loaded.
THREADING
Tape loading
UNTHREADING
Tape unloading
STANDBY OFF
Standby off mode
T. RELEASE
Tape tension released
STOP
Stop mode
F. FWD
Fast forward mode
REW
Rewind mode
Preroll mode
Indication
Description
PREROLL
CNT
Count value of the time counter
PLAY
Playback mode (servo unlocked)
TCR
Time code data from time code reader
(factory default setting)
PLAY LOCK
Playback mode (servo locked)
PLAY-PAUSE
Temporary stop of playback
UBR
User bit data from time code reader
REC
Record mode (servo unlocked)
TCR.
Time code data from VITC reader a)
REC LOCK
Record mode (servo locked)
UBR.
User bit data from VITC reader a)
REC-PAUSE
Temporary stop of recording
TCG
Time code data from time code generator
EDIT
Edit mode (servo unlocked)
UBG
User bit data from time code generator
EDIT LOCK
Edit mode (servo locked)
T*R b)
Time code data from time code reader. The
asterisk indicates an interpolation by the time
code reader to make up for the time code
data not correctly read from the tape.
JOG STILL
Still picture in jog mode
JOG FWD
Jog mode in forward direction
JOG REV
Jog mode in reverse direction
User bit data from the time code reader. The
asterisk indicates that last data is retained by
the time code reader, as the new data has
not been read correctly from the tape.
SHUTTLE (Speed)
Shuttle mode
U*R b)
a) You can switch between TC and VITC using the TC SELECT menu item
(see page 61).
b) “*” is displayed when data cannot be read in correctly.
B Drop frame indication for time code reader (on
DSR-1800 only)
42
D VITC field indication
.
Drop frame mode (factory default setting)
:
Non-drop frame mode
Setting the Time Data
AUTO EDIT
Automatic editing mode
PREVIEW
Preview mode
REVIEW
Review mode
To display the desired time data in the time
counter display
To reset the CNT value
Press the RESET (NO) button on the menu control panel.
This resets the CNT value to 0:00:00:00.
Note
Time data type indicators
During playback, if the recording on the tape includes
discontinuities, the counter may operate incorrectly at the
corresponding points.
Time counter display
dB
0
OVER
-12
-20
-30
-40
-60
dB
0
dB
0
1
-12
0
-20
-1
-2
-30
-40
1
-60
OVER
dB
0
dB
0
1
-12
0
-20
-1
-2
-30
-40
2
-60
OVER
dB
0
dB
0
1
-12
0
-20
-1
-2
-30
-40
3
-60
OVER
dB
INPUT
V:SDTI
SDTI
Using the Internal Time Code
Generator
i.LINK
0
1
VIDEO
0
CH11/2
-1
AUDIO
-2
4
CH23/4
PB FS
COMPOSITE Y-R,B S VIDEO
ANALOG AES/EBU
ANALOG AES/EBU
48k44.1k32k REC MODE
SDI
SG
SDI
SG
SDI
SG
2CH4CH
You can set the initial time code value before recording the
time code generated by the internal time code generator
onto a tape. In addition, you can use the user bits to record
such data as the date, time, scene number, reel number, or
other useful information.
COUNTER SEL button
B
MARK
To set the initial time code value and user
bit data
Open the door on the lower part of the front panel, and
press the COUNTER SEL button.
Each press of this button cycles through three options:
CNT value, time code, and user bit data. The time data type
indicator for each option lights as it is selected.
Time data
type
indicator
Time data shown in the time counter
display
COUNTER
CNT (count value of the time counter)
TC
Time code (when recording, the time code is
generated by the internal time code
generator; when playing back, the time code
is read from the tape.)
U-BIT
User bit data (when recording, the user bit
data is according to the most recent settings;
when playing back, the user bit data is read
from the tape.)
Note
When the REMOTE button on the front panel is lit, the
COUNTER SEL button does not operate while the tape is
moving. In such cases, use the external equipment
connected to the REMOTE connector on the rear panel to
select the time data.
1
A
B
MARK
2
1
3
4,5,6
Chapter 3 Convenient Functions for Editing Operation
A
When an external time code generator is connected to the
TIME CODE IN connector, the internal time code
generator can be locked to (synchronized with) an external
time code.
7
Press the COUNTER SEL button to light the time data
type indicator “TC” or “U-BIT.”
TC: To set the initial time code value.
U-BIT: To set user bit data
The current time code value or user bit data is shown
in the time counter display.
Setting the Time Data
43
2
Set the TIME CODE menu items (see page 60) as
shown below.
Menu item
Setting
TC MODE
“INT PRESET”
RUN MODE
“FREE RUN” or “REC RUN”
DF MODE
Normally “ON (DF)”
(for DSR-1800 only)
3
Press the TC PRESET button on the menu control
panel.
The current setting is shown on the monitor screen and
in the time counter display on the front panel. The
leftmost digit keeps flashing.
One of the following menu screens is displayed on the
monitor depending on the setting made in step 1.
Chapter 3 Convenient Functions for Editing Operation
TC PRESET MODE
UB PRESET MODE
TCG 00:00:00:00
UBG 00:00:00:00
INC/DEC : ( )( )KEY
SHIFT : ( )( )KEY
CLEAR : RESET KEY
DATA SAVE :
SET KEY
ABORT : TC PRESET KEY
INC/DEC : ( )( )KEY
SHIFT : ( )( )KEY
CLEAR : RESET KEY
DATA SAVE :
SET KEY
ABORT : TC PRESET KEY
Initial time code value setting
screen
User bit setting screen
Note
If you press the TC PRESET button while CNT value
is being displayed, the message “COUNTER MODE
IS SELECTED.” will appear on the monitor screen
and “CNT mode!” will appear in the time counter
display on the front panel. If this happens, press the
COUNTER SEL button to light the time data type
indicator “TC” or “U-BIT.”
4
Use the K and k buttons to move the flashing digit
to the value to be changed.
5
Use the J and j buttons to change the value of the
flashing digit.
Enter hexadecimal values (0 to 9, A to F) when setting
user bit data.
6
44
Repeat steps 4 and 5 until you have set the desired
values for all digits.
To set a value of 00:00:00:00, simply press the RESET
(NO) button.
Setting the Time Data
7
Press the SET (YES) button.
The message “NOW SAVING...” appears on the
monitor screen, “Saving...” appears in the time counter
display, and the new settings are stored in memory.
After this saving operation is completed, the monitor
screen and the time counter display return to their
usual status.
Note
The set data may be lost if you power off the unit while
the above saving operation is in progress. Wait until
the saving operation is completed before powering off.
Advancement of internal time code
generator
The internal time code generator can advance in either of
two modes, which can be set with the RUN MODE menu
item (see page 60).
FREE RUN: Advancement starts when the data saving
operation is completed.
REC RUN: Advancement starts when recording starts and
stops when recording stops.
To set the current time as the initial time
code value
In step 2 above, set the RUN MODE menu item to FREE
RUN, then set the current time (format: HH:MM:SS:FF =
hours: minutes:seconds:frame number) in step 3 and
subsequent steps.
Synchronizing Internal and External
Time Codes
Rerecording the Time Code—TC
Insert Function
The internal time code generator can be synchronized with
an external time code (LTC) input to this unit.
The TC insert function makes it possible to use the internal
time code generator to rewrite time code or user bits when
the time code recorded on a tape is discontinuous.
You can start recording time code from an initial value
which can be set freely (see page 43).
To synchronize the internal time code to
external time code
Input an external time code (LTC) signal to the TIME
CODE IN connector, then set the TC MODE menu item
(see page 60) to EXT REGEN.
The internal time code generator locks onto the external
time code and starts advancing. Once the internal time
code generator has been synchronized in this way, you can
disconnect the external time code input and this unit will
maintain the synchronized time code.
Notes
• Use a tape which is recorded in the DVCAM format.
(You cannot use the TC insert function with a tape
recorded in DV format.)
• The time code recording starts from the current tape
position. Cue the tape up beforehand to the required start
position.
• If you use a tape on which ClipLink log data is recorded,
the ClipLink log data will be lost.
Note
Once an external time code signal has been input, the
internal time code advancement mode and frame count
mode are automatically set as follows:
Advancement mode: FREE RUN
Frame count mode: Same as external time code (drop
frame or non-drop frame)
To confirm external synchronization
Press the STOP button to put the unit into stop mode, then
press the REC button.
Look at the time counter display and check that the time
code value displayed there matches the external time code
value.
A
B
MARK
1
1
2,4
3,5
7,8
Open the door on the lower part of the front panel, then
press the MENU button.
SYSTEM MENU
SETUP MENU
AUTO FUNCTION
HOURS METER
Setup menu
Time counter display
Chapter 3 Convenient Functions for Editing Operation
When the selected input mode is “SDTI” or “i.LINK” (the
SDTI or i.LINK indicator is lit in the INPUT display),
setting the TC MODE menu item (see page 60) to EXT
REGEN causes the internal time code generator to
automatically synchronize with the external time code
input to the unit via the SDTI or i.LINK interface.
Monitor screen
Setting the Time Data
45
2
Press the J or j button to select “AUTO
FUNCTION.”
SYSTEM MENU
SETUP MENU
AUTO FUNCTION
HOURS METER
5
Press the k button.
The following message appears.
Auto func
TC INSERT
Time counter display
Set tape!
Time counter display
INSERT THE TAPE IN
THIS VTR.
ABORT:MENU KEY
Monitor screen
Monitor screen
3
Press the k button.
6
This displays the items in the level 1 of the auto mode
execution menu.
Chapter 3 Convenient Functions for Editing Operation
AUTO FUNCTION MENU
SDTI DUBBING
i.LINK DUBBING
TC INSERT
A message to confirm the TC insert operation appears.
TC INSERT
TC insert?
Time counter display
Time counter display
START TC INSERT?
START:YES KEY
ABORT:MENU KEY
Monitor screen
Monitor screen
4
Press the j button to select “TC INSERT.”
AUTO FUNCTION MENU
SDTI DUBBING
i.LINK DUBBING
TC INSERT
Monitor screen
46
SDTI DUB
Insert the cassette.
Setting the Time Data
TC insert
Time counter display
To cancel the TC insert operation
Press the MENU button.
7
Press the SET (YES) button.
Time code recording starts from the current tape
position.
TC INSERT
Executing
Time counter display
EXECUTING.
TCR 00:00:00:00
UBR 00:00:00:00
ABORT:MENU KEY
Monitor screen
When the recording ends, the message “TC INSERT
COMPLETED. PUSH THE YES BUTTON.” appears
on the monitor screen and “Completed” appears in the
time counter display.
Press the SET (YES) button to exit the menu.
Chapter 3 Convenient Functions for Editing Operation
8
Setting the Time Data
47
High-Speed and LowSpeed Search—Quickly
and Accurately
Determining Editing
Points
Use the search function to easily locate the desired scene
and to quickly and accurately determine edit points.
When F. FWD/REW under the AUTO EE SELECT menu
item (see page 57) is set to PB (factory default setting), you
can use the F FWD and REW buttons on this unit or
external equipment for high-speed search.
Search Operations via External
Equipment
Note
When controlling this unit from external equipment, be
sure to turn on or off the buttons in the remote control
setting section on the front panel of the unit as shown in the
following table.
External equipment Buttons in the remote control
setting section
Editing control unit
connected to the
REMOTE connector
Turn on both the REMOTE and 9PIN
buttons.
SIRCS-compatible
remote control unit
connected to the
CONTROL S
connector
Turn off the REMOTE button.
Equipment
Turn on both the REMOTE and
connected to the i.DV i.LINK buttons.
IN/OUT connector
For description on how to carry out search operations via
external equipment, see the operating instructions for the
equipment.
Chapter 3 Convenient Functions for Editing Operation
You can control the unit in the following operation modes
from an editing control unit (ES-7, PVE-500, etc.)
connected to the REMOTE connector on the rear panel or
from a SIRCS-compatible remote control unit such as the
DSRM-10 connected to the CONTROL S connector on the
front panel.
Shuttle: Use this mode to view color video playback at
speeds ranging from 0 to 60 times normal speed in
both directions.
Note
When controlling the unit from the DSRM-10 for
shuttle-mode search, the maximum search speed is 16
times normal speed in both directions.
Jog: Use this mode for low-speed search and frame-byframe search.
Digital slow: Use this mode for noise-free color video
playback at speeds ranging from 0 to 1/2 times normal
speed in both directions.
Still: Use this mode to view a still picture of any field.
Jog audio: Use this mode to monitor the audio at speeds
ranging from 1 to 1/30 times normal speed in both
directions.
48
High-Speed and Low-Speed Search—Quickly and Accurately Determining Editing Points
Search Operations on This Unit
SHUTTLE indicator
When you perform searching on this unit, be sure to turn
off the REMOTE button on the front panel.
dB
0
-12
-20
-30
-40
-60
OVER
dB
0
dB
0
1
-12
0
-20
-1
-2
-30
-40
1
-60
OVER
dB
0
dB
0
1
-12
0
-20
-1
-2
-30
-40
2
-60
OVER
dB
0
dB
0
1
-12
0
-20
-1
-2
-30
-40
3
-60
OVER
dB
INPUT
V:SDTI
SDTI
i.LINK
0
1
VIDEO
0
CH11/2
-1
AUDIO
-2
4
CH23/4
PB FS
COMPOSITE Y-R,B S VIDEO
ANALOG AES/EBU
ANALOG AES/EBU
48k44.1k32k REC MODE
SDI
SG
SDI
SG
SDI
SG
2CH4CH
Playing back in jog mode
In jog mode, you can control the speed of playback by the
speed of turning the search dial. The playback speed range
is ±1 times normal speed by factory default. The speed
variation range and pattern can be changed with the JOG
RESPONSE menu item (see page 58).
To carry out playback in jog mode, use the following
procedure.
JOG indicator
dB
0
-12
-20
-30
-40
-60
OVER
dB
0
dB
0
1
-12
0
-20
-1
-2
-30
-40
1
-60
OVER
dB
0
dB
0
1
-12
0
-20
-1
-2
-30
-40
2
-60
OVER
dB
0
dB
0
1
-12
0
-20
-1
-2
-30
-40
3
-60
OVER
dB
INPUT
V:SDTI
SDTI
3 1 1,2,3
1
Pressing the search dial toggles between jog mode and
shuttle mode.
i.LINK
0
1
VIDEO
0
CH11/2
-1
AUDIO
-2
4
CH23/4
PB FS
COMPOSITE Y-R,B S VIDEO
ANALOG AES/EBU
ANALOG AES/EBU
48k44.1k32k REC MODE
SDI
SG
SDI
SG
SDI
SG
Press the SEARCH button or search dial so that the
SHUTTLE indicator in the display section is lit.
2CH4CH
2
Turn the search dial to the desired angle corresponding
to the desired playback speed.
1 1,2,3
1
Press the SEARCH button or search dial so that the
JOG indicator in the display section is lit.
Turn the search dial in the desired direction at the
speed corresponding to the desired playback speed.
Playback in jog mode starts.
3
To stop playback in shuttle mode, return the search
dial to the center position, or press the STOP button.
To return to normal-speed playback
Press the PLAY button.
Pressing the search dial toggles between jog mode and
shuttle mode.
2
3
To alternate between normal-speed playback and
shuttle mode playback
Set the search dial to the position corresponding to the
desired shuttle playback speed, then switch between
normal-speed playback and shuttle playback by pressing
the PLAY and SEARCH buttons alternately.
For intermittent shuttle mode playback, press the STOP
and SEARCH buttons alternately.
Chapter 3 Convenient Functions for Editing Operation
Playback in shuttle mode starts.
To stop playback in jog mode, stop turning the search
dial.
Playing back in shuttle mode
In shuttle mode, you can control the speed of playback by
the angular position of the search dial. The range of
playback speed is ±32 times normal speed by factory
default. This can be changed with the SHUTTLE menu
item (see page 57). The search dial has detents at the
positions of still image and ±10 times normal speed.
To carry out playback in shuttle mode, use the following
procedure.
High-Speed and Low-Speed Search—Quickly and Accurately Determining Editing Points
49
Use the following procedure.
Digitally Dubbing Signals
in DVCAM Format
A
In addition to straightforward tape dubbing, you can also
use this unit to dub automatically from the beginning of the
tape to the end through the SDTI (QSDI) or i.LINK
interface.
• To use the SDTI (QSDI) interface, the optional DSBK1802 board is required.
• To use the i.LINK interface, the optional DSBK-1803
board is required.
When a tape recorded on a DSR-1/1P Digital
Videocassette Recorder or DSR-130/130P Digital
Camcorder is dubbed, the ClipLink log data held in the
cassette memory is also copied.
B
MARK
1,9
1
2,4
3,4,5
7
Press the MENU button on the menu control panel.
SYSTEM MENU
SETUP MENU
AUTO FUNCTION
HOURS METER
Setup menu
Time counter display
Notes
Chapter 3 Convenient Functions for Editing Operation
• Use a tape recorded in the DVCAM format. A tape
recorded in DV format cannot be used as a source tape
for dubbing through the SDTI (QSDI) or i.LINK
interface.
• Regardless of the audio recording mode setting of this
unit, dubbing is performed with the original audio
recording mode unchanged (two-channel/48 kHz mode
or four-channel/32 kHz mode).
• Approximately the last 2 minutes of the tape may not be
copied because of differences in tape lengths. (If an
index picture is recorded in this portion, it may also not
be copied.)
• A continuous recorded section of approximately 5
seconds is required before the recording start point. It is
recommended to record beforehand color bars or a
similar signal at the start point of the source tape to be
dubbed on this unit.
Connections for dubbing via SDTI (QSDI)
interface
To carry out dubbing through the SDTI (QSDI) interface,
connect the REMOTE and SDTI (QSDI) IN/OUT
connectors on this unit to those on the DSR-85/85P/80/
80P/60/60P/70/70P/2000/2000P/1800/1800P/1600/
1600P.
For details of the connections and switch settings, see
“Connections for SDTI (QSDI) Dubbing” on page 86.
Connections for dubbing via i.LINK interface
To carry out dubbing through the i.LINK interface,
connect the i.DV IN/OUT connectors on this unit and the
player.
50
Digitally Dubbing Signals in DVCAM Format
Monitor screen
2
Press the J or j button to select “AUTO
FUNCTION.”
SYSTEM MENU
SETUP MENU
AUTO FUNCTION
HOURS METER
Monitor screen
Auto func
Time counter display
3
6
Press the k button.
This displays the items in the level 1 of the auto mode
execution menu.
AUTO FUNCTION MENU
SDTI DUBBING
i.LINK DUBBING
TC INSERT
Insert the source tape in the player, and the recording
tape in this unit.
A message to confirm the dubbing operation appears.
SDTI DUBBING
(A/V/TC/CM)
SDTI DUB
Start dub?
Time counter display
Time counter display
START QSDI DUBBING?
START:YES KEY
ABORT:MENU KEY
Monitor screen
Monitor screen
4
Press the k button to display the menu level 2 for the
item “SDTI DUBBING,” and select the data to be
dubbed with the j button.
To cancel the dubbing operation
Press the MENU button.
7
>A/V/TC/CM
Time counter display
SDTI DUBBING
(A/V/TC/CM)
Executing
Time counter display
EXECUTING.
TCR 00:00:00:00
UBR 00:00:00:00
Monitor screen
ABORT:MENU KEY
Monitor screen
5
Press the k button.
The following message appears.
SDTI DUBBING
(A/V/TC/CM)
To end the dubbing operation while it is in progress
Press the STOP button.
Set tape!
When the dubbing is completed, message
“COMPLETED” appears on the monitor screen and
“Completed” in the time counter display.
The source tape and recording tape are both
automatically rewound to the beginning, and the
cassettes ejected. When the cassette is ejected, this unit
returns to the state in step 5.
Time counter display
INSERT RECORD TAPE IN
THIS VTR AND SOURCE
TAPE IN THE PLAYER VTR.
ABORT:MENU KEY
Chapter 3 Convenient Functions for Editing Operation
The tape is automatically wound back to the
beginning, and dubbing starts.
Example: Selecting “A/V/TC/CM”
AUTO FUNCTION MENU
SDTI DUBBING
A/V
A/V/TC
A/V/TC/CM
Press the SET (YES) button.
8
To continue by dubbing another tape, repeat steps 6
and 7.
9
When the dubbing is completed, press the MENU
button to exit the menu.
Monitor screen
Digitally Dubbing Signals in DVCAM Format
51
If the following message appears in step 6 for an
A/V/TC/CM dubbing operation
SDTI DUBBING
(A/V/TC/CM)
CM capacity!
Time counter display
CM MEMORY STORAGE
CAPACITY OF THE RECORD
TAPE IS TOO SMALL.
ABORT:MENU KEY
Monitor screen
When carrying out A/V/TC/CM dubbing, if you insert the
cassettes in step 6, the cassette memory capacity of the
cassettes inserted in both this unit and the player are
checked automatically.
If the cassette memory capacity of the source tape is larger
than that of the recording tape, the above message appears.
In this case, replace the recording tape by a tape with a
larger cassette memory capacity.
Chapter 3 Convenient Functions for Editing Operation
If the following message appears in step 7 for an
A/V/TC/CM dubbing operation
SDTI DUBBING
(A/V/TC/CM)
Copy CM?
Time counter display
SDTI DUBBING IS ABORTED.
EXECUTE CM COPY?
COPY
:YES KEY
NOT COPY:NO KEY
Monitor screen
When carrying out A/V/TC/CM dubbing, if you press the
STOP button to stop dubbing in step 7, or if dubbing stops
because the source tape is longer than the recording tape,
the above message appears to confirm whether or not to
copy the contents of the cassette memory.
To copy the contents of the cassette memory, press the
SET (YES) button.
If you do not wish to copy the contents of the cassette
memory, press the RESET (NO) button. If you press the
RESET (NO) button, however, the contents of the cassette
memory may not agree with the material recorded on the
tape.
52
Digitally Dubbing Signals in DVCAM Format
Menu Settings
Chapter
4
Menu Organization
As shown in the following figure, the menu system
consists of four levels and is functionally divided into three
subsystems: the setup menu, the auto mode (AUTO
FUNCTION) execution menu and the digital hours meter
display menu. This chapter mainly describes the setup
menu, showing its contents and how to operate it.
For details of the AUTO FUNCTION menu, see “Digitally
Dubbing Signals in DVCAM Format” on page 50 and
“Rerecording the Time Code—TC Insert Function” on
page 45.
For details of the digital hours meter display, see “Regular
Checks” on page 91.
The items of the setup menu are divided into several
functional groups on level 1, and except for the MENU
GRADE item the settings themselves are made on level 2
or level 3.
Also, the menu items are divided into two categories
according to how frequently they are accessed: the “basic”
items, to which frequent access is normally required, and
the “enhanced” items, which are less frequently used. In
the following figure, the items shown in boldface are basic
items, and the other items are enhanced items.
The menu settings are saved in non-volatile memory,
which means they are not erased when you power off the
unit after executing the setting operation.
Menu Organization
53
Menu organization
Menu selection level
SETUP MENU
Level 1
OPERATIONAL FUNCTION
Level 2
Level 3
REPEAT FUNCTION
REPEAT MODE
REPEAT TOP
REPEAT END
A PRESET
B PRESET
AUTO EE SELECT
CASSETTE OUT
F.FWD/REW
STOP
STANDBY OFF
LOCAL ENABLE
REC INHIBIT
A1 EDIT CH
A2 EDIT CH
SEARCH ENABLE
MAX SRCH SPEED
SHUTTLE
F.FWD/REW
JOG RESPONSE
PREROLL TIME
AFTER CUE-UP
PLAY START
AUTO REW
A MODE CHANGE
Chapter 4 Menu Settings
DISPLAY CONTROL
CHARA. DISPLAY
CHARA. POSITION
CHARA. TYPE
CHARA. VSIZE
DISPLAY INFO
SUB STATUS
MENU DISPLAY
PEAK HOLD
OVER DISP HOLD
BRIGHTNESS
ALARM
REF ALARM
TIME CODE
TC MODE
RUN MODE
DF MODE a)
TC SELECT
VITC
TCG REGEN
UB BINARY GP.
VITC POS SEL-1
VITC POS SEL-2
VITC OUTPUT
EE OUT PHASE
MUTE IN SRCH
TAPE PROTECTION
FROM STOP
FROM STILL
STOP TIMER
STILL TIMER
NEXT MODE
(Continued)
a) Menu item for DSR-1800 only
54
Menu Organization
Menu selection level
Level 1
Level 2
Level 3
(Continued)
VIDEO CONTROL
AUDIO CONTROL
EE DELAY
INT VIDEO SG
STD/NON-STD
OUT REF SEL
SETUP REMOVE a)
SETUP ADD a)
CC(F1) BLANK a)
CC(F2) BLANK a)
WIDE MODE
ESR MODE
PROCESS CONTROL
CONTROL DEV
C PHASE MODE
ADJ RANGE
VIDEO GAIN
CHROMA GAIN
CHROMA PHASE
SETUP LEVEL a)
BLACK LEVEL b)
INPUT BLANK b)
LINE 335
REC MODE
INPUT ARRANGE
REC LEVEL
LEVEL SELECT
INT AUDIO SG
OUTPUT CH3/4
OUTPUT PHASE
JOG CONTROL
SHUTTLE MUTE
AUDIO EDIT
DV PB ATT
REF LEVEL
CH1 IN LEVEL
CH2 IN LEVEL
CH3 IN LEVEL
CH4 IN LEVEL
OUTPUT LEVEL
SYSTEM EE MODE
SETUP BANK OPERATION
RECALL BANK1
RECALL BANK2
RECALL BANK3
RECALL BANK4
SAVE BANK 1
SAVE BANK 2
SAVE BANK 3
SAVE BANK 4
Chapter 4 Menu Settings
DIGITAL PROCESS
MENU GRADE
AUTO FUNCTION
SDTI DUBBING
i.LINK DUBBING
TC INSERT
HOURS METER
A/V
A/V/TC
A/V/TC/CM
A/V
A/V/TC
A/V/TC/CM
T1:OPERATION
T2:DRUM ROTATION
T3:TAPE RUNNING
CT:THREADING
a) Menu item for DSR-1800 only
b) Menu item for DSR-1800P only
Menu Organization
55
Menu Contents
Setup Menu
Examples:
The purpose and settings of the setup menu items are
described below.
Indications of menu items and settings
• In the table below entitled “Menu contents,” the
indication of each menu item or setting on the monitor
screen is shown first, then the indication of the same item
or setting in the time counter display of this unit is shown
in square brackets ([ ]).
Indication on monitor
screen
Indication in time counter
display
OPERATIONAL FUNCTION
[Operational]
CASSETTE OUT
[>> Cass. out]
*EE
[>>> EE]
• Settings preceded by an asterisk (such as *EE) are
factory default settings.
• In the time counter display, one to three “>” symbols
may precede item or setting indications depending on the
current menu level. Larger numbers of “>” symbols
indicate lower menu levels.
Menu contents
OPERATIONAL FUNCTION [Operational]: Operation
settings
REPEAT FUNCTION [>REP
FUNC]: Make settings for
repeat playback mode.
Description of settings
REPEAT MODE
*OFF [>>> OFF]: Do not put the unit into repeat playback
[>>REPEAT MD]:
mode.
Determine whether or ON [>>> ON]: Put the unit into repeat playback mode.
not to put the unit into ON (FREEZE) [>>> FREEZE]: Put the unit into freeze
repeat playback mode.
playback mode. In this case, while the unit is cueing up to
the repeat start point, the freeze picture of the repeat end
point is displayed.
Chapter 4 Menu Settings
REPEAT TOP [>>REP
TOP]: Determine
whether the repeat
start point is the
beginning of tape or
point A.
*TAPE TOP [>>>Tape top]: The repeat start point is the
beginning of tape.
A POINT [>>>A point]: The repeat start point is point A as set
by the user.
REPEAT END [>>REP
*VIDEO END [>>>VD end]: The repeat end point is the end
END]: Determine
of the video recorded portion.
whether the repeat end TAPE END [>>>Tape end]: The repeat end point is the end of
point is the end of the
tape.
video recorded portion, B POINT [>>>B point]: The repeat end point is point B as set
the end of tape or point
by the user.
B.
A PRESET [>>A preset]: For details, see “Setting Points A and B for Repeat Playback”
Specify a time code
on page 34.
value to be used as the
setting of point A.
B PRESET [>>B preset]: For details, see “Setting Points A and B for Repeat Playback”
Specify a time code
on page 34.
value to be used as the
setting of point B.
56
Menu Contents
OPERATIONAL FUNCTION [Operational]: Operation
settings
Description of settings
AUTO EE SELECT [> Auto EE]: CASSETTE OUT [>>
Determine whether the unit
Cass. out]: Operations
enters EE mode or PB mode
when the cassette has
when audio and video
been ejected
signals from other equipment
F. FWD/REW [>> F. FWD/
are input.
REW]: Operations
When this unit is used as the
when in fast forward or
recorder for cut editing, it is
rewind mode
possible to output the input
audio and video signals to
STOP [>> STOP]:
the monitor. This enables
Operations when in
editing operation to be
stop mode
carried out using a single
monitor.
STANDBY OFF [>> STBY
OFF]: Operations
when in standby off
mode
*EE [>>> EE]: Output video and audio signals received from
other equipment.
PB [>>> PB]: Mute video and audio signals.
LOCAL ENABLE [> Local ENA]: Select which of the tape
transport control buttons (EJECT, REW, PLAY, F FWD,
STOP, and REC) operate when the REMOTE button is lit.
ALL DISABLE [>> All DIS]: All of the tape transport control
buttons are disabled.
*STOP & EJECT [>> STOP & EJ]: Only the STOP and
EJECT buttons are enabled.
ALL ENABLE [>> All ENA]: All of the tape transport control
buttons are enabled, and settings such as preroll time
change or time data display selection are effective.
REC INHIBIT [>REC INH]: Determine whether to prohibit
recording on tape.
*OFF [>> OFF]: Do not prohibit recording on tape.
ON [>> ON]: Prohibit recording on tape. (The REC INHIBIT
indicator on the front panel lights.)
EE [>>> EE]: Output video and audio signals received from
other equipment.
*PB [>>> PB]: The unit enters playback mode and outputs a
playback video signal. Audio signals are muted.
EE [>>> EE]: Output video and audio signals received from
other equipment.
*PB [>>> PB]: The unit enters playback mode and outputs a
still picture.
EE [>>> EE]: Output video and audio signals received from
other equipment.
*PB [>>> PB]: The unit enters playback mode and outputs a
still picture.
A2 EDIT CH [> A2 Edit CH]: Determine which audio channel *CH-2 [>> CH-2]: Assign to channel 2.
the EDIT PRESET command set on an editing control unit CH-3 [>> CH-3]: Assign to channel 3.
(such as the PVE-500) for A2 is assigned to.
CH-4 [>> CH-4]: Assign to channel 4.
CH-3 & CH-4 [>> CH-3&4]: Assign to channel 3 and channel
4.
SEARCH ENABLE [>Search ENA]: Select how the unit enters *DIAL DIRECT [>> DIAL]: Press the SEARCH button or,
the search mode.
except during recording or editing, turn the search dial.
VIA SEARCH KEY [>> via KEY]: Press the SEARCH button.
MAX SRCH SPEED [>Max
SRCH]: Specify the
maximum tape speed in
search mode (shuttle) and
F.FWD (fast forward)/REW
(rewind) mode.
SHUTTLE [>>SHUTTLE]:
Specify the maximum
tape speed in search
mode (shuttle).
X60 [>>> X60]: Maximum 60 times normal speed
*X32 [>>> X32]: Maximum 32 times normal speed
X16 [>>> X16]: Maximum 16 times normal speed
F.FWD/REW [>>F.FWD/
REW]: Specify the
maximum tape speed
in F.FWD/REW mode.
MAX [>>> MAX]: No maximum tape speed is specified.
*X85 [>>> X85]: Maximum 85 times normal speed
X60 [>>> X60]: Maximum 60 times normal speed
X32 [>>> X32]: Maximum 32 times normal speed
Chapter 4 Menu Settings
A1 EDIT CH [> A1 Edit CH]: Determine which audio channel *CH-1 [>> CH-1]: Assign to channel 1.
the EDIT PRESET command set on an editing control unit CH-2 [>> CH-2]: Assign to channel 2.
(such as the PVE-500) for A1 is assigned to.
CH-3 [>> CH-3]: Assign to channel 3.
CH-1 & CH-2 [>> CH-1&2]: Assign to channel 1 and channel
2.
Note
When this item is set to MAX, the playback video signal is
muted.
Menu Contents
57
OPERATIONAL FUNCTION [Operational]: Operation
settings
Description of settings
JOG RESPONSE [>JOG dial]: Select the tape speed
*TYPE1 (-1 to +1) [>> type 1]: Tape speed varies linearly
characteristics for the search dial rotation rate in jog mode.
over the range −1 to +1.
TYPE2 (-3 to +3) [>> type 2]: Tape speed varies stepwise as
shown in the figure below over the range −3 to +3.
(Characterized by a zone around −1 and +1 where the
tape speed is independent of the rotation rate)
TYPE3 (-3 to +3) [>> type 3]: Tape speed varies linearly over
the range −3 to +3, as shown in the figure below.
TYPE3
TYPE2
Speed
+3
FWD
+1
RVS
+3
FWD
Rotation rate
Rotation rate
-1
RVS
Speed
FWD
RVS
-3
FWD
RVS
-3
Chapter 4 Menu Settings
PREROLL TIME [> Preroll]: Set the preroll time.
0 SEC [>> 0 sec] to 15 SEC [>> 15 sec]: The preroll time
can be set in one-second increments to between 0 and 15
seconds.
A preroll time of at least 5 seconds is recommended when
using this unit for editing. When an editing control unit such as
the PVE-500 has been connected, this setting is disabled and
the setting on the editing control unit is in effect. Operations
such as the preroll time setting and the time data switching
operation are also performed on the editing control unit.
Factory default setting: 5 SEC [>> 5 sec]
AFTER CUE-UP [> After CUE]: Select the operating mode
following cue-up.
*STOP [>> STOP]: Stop mode
STILL [>> STILL]: Output still pictures in search mode.
PLAY START [> PLAY start]: Set the timing for switching from 16 FRAME DELAY [>> 16 delay] to 4 FRAME DELAY
stop mode to playback mode.
[>> 4 delay]: The larger the numerical value, the
In an editing system including an editing control unit such as
longer the delay. By adjusting this setting, it is
the PVE-500, you can adjust this setting so that the delay
possible to reduce the phase synchronization time
before switching to playback mode is the same on all the decks
and preroll time during editing.
of the editing system. It is then no longer necessary to
Factory default setting: 5 FRAME DELAY [>> 5 delay] (for
synchronize the decks for editing, and the preroll time can be
DSR-1800) or 4 FRAME DELAY [>> 4 delay] (for DSRshortened.
1800P)
AUTO REW [>Auto REW]: Select whether to rewind the tape DISABLE [>> DISABLE]: Do not rewind the tape
automatically when recording or playback reaches the end
automatically.
of a tape.
*ENABLE [>> ENABLE]: Rewind the tape automatically.
A MODE CHANGE [>Aud change]: Determine whether or not *OFF [>> OFF]: Do not permit.
to permit an insert editing that uses a different audio
ON [>> ON]: Permit.
recording mode (2- or 4-channel mode) from that which
was used for the tape loaded in the recorder.
58
Menu Contents
DISPLAY CONTROL [Display]: Settings related to
indications on the monitor and the unit
Description of settings
CHARA. DISPLAY [> Chara disp]: Determine whether or not
to output text (such as time code values) from the VIDEO
OUT 2 (SUPER) connector.
OFF [>> OFF]: Do not output text. (In spite of this setting,
pressing the MENU button causes menu text to be
output.)
*ON [>> ON]: Output text.
CHARA. POSITION [> Chara pos]: Set the position of text
Use JjK k buttons on the menu control panel to adjust the
superimposed on output from the VIDEO OUT 2 (SUPER) text position while watching the monitor screen.
To return to the level 1 of the setup menu, press the MENU
connector to the monitor.
button.
CHARA. TYPE [> Chara type]: Set the type of characters in
text superimposed on output from the VIDEO OUT 2
(SUPER) connector to the monitor.
Make the following settings while watching the monitor screen.
*WHITE (WITH BKGD) [>> White]: White characters on black
background
BLACK (WITH BKGD) [>> Black]: Black characters on white
background
WHITE/OUTLINE [>> W/outline]: White characters with black
outline
BLACK/OUTLINE [>> B/outline]: Black characters with white
outline
CHARA. VSIZE [>Chara size]: Determine the vertical size of Make the selection while watching the monitor screen.
characters such as time code output from the VIDEO OUT *×
×1 [>> ×1]: Standard size
2 (SUPER) connector for superimposed display on the
×2 [>> ×2]: 2 times standard size
monitor.
SUB STATUS [> Sub status]: Select supplementary status
*OFF [>> OFF]: Nothing of supplementary status information
information superimposed on output from the VIDEO OUT EDIT PRESET [>> Edit pre]: Indications of the editing mode
2 (SUPER) connector to the monitor.
settings made from the connected editing control unit
TC MODE [>> TC mode]: Indications of the operating mode
of internal time code generator
REMAIN [>> Remain]: Remaining capacity of the tape
AUDIO MIXING [>> Aud Mix]: Indications of input audio
mixing
ALL [>> ALL]: All of the above-mentioned items of
supplementary status information
Chapter 4 Menu Settings
DISPLAY INFO [> DISP info]: Select information
*TIME DATA & STATUS [>> Time&STA]: Time data and
superimposed on output from the VIDEO OUT 2 (SUPER)
operating mode indications
connector to the monitor.
TIME DATA & UB [>> Time&UB]: Time data selected using
the COUNTER SEL button, and user bit data (When user
bit data is selected using the COUNTER SEL button, user
bit data and time code are shown.)
TIME DATA & CNT [>> Time&CNT]: Time data selected
using the COUNTER SEL button, and CNT value (When
CNT is selected using the COUNTER SEL button, CNT
value and time code are shown.)
TIME DATA & TIME[>> Time&Time]: Time data and VITC
TIME DATA ONLY [>> Time]: Time data only
REC DATE & TIME [>> REC Date]: The time data selected
with the COUNTER SEL button is shown in the time
counter display, and the date and time of recording are
shown on the monitor screen.
For details of supplementary status information displayed on
the monitor when a setting other than OFF is selected, see
“Displaying Supplementary Status Information” on page 74.
MENU DISPLAY [> Menu DISP]: Set the type of characters in Make the following settings while watching the monitor screen.
menu text superimposed on output from the VIDEO OUT 2 *WHITE (WITH BKGD) [>> White]: White characters on black
(SUPER) connector to the monitor.
background
BLACK (WITH BKGD) [>> Black]: Black characters on white
background
WHITE/OUTLINE [>> W/outline]: White characters with black
outline
BLACK/OUTLINE [>> B/outline]: Black characters with white
outline
Menu Contents
59
DISPLAY CONTROL [Display]: Settings related to
indications on the monitor and the unit
Description of settings
PEAK HOLD [>Peak hold]: Set the peak hold time for the
audio level meters.
OFF [>> OFF] to 1.5 SEC [1.5 sec]: Set the peak hold time in
the range of OFF (no peak hold) to 1.5 seconds in 0.1
second steps.
Factory default setting: OFF [>> OFF]
OVER DISP HOLD [> Hold OVER]: Determine whether or not *OFF [>> OFF]: Do not hold the OVER indication display.
to hold the OVER indication display on the audio level
ON (HOLD) [>> ON]: Hold the OVER indication display.
meters once the indications light.
Note
With ON selected, once the display is held it will remain held
unless you change the setting to OFF.
BRIGHTNESS [> Brightness]: Set the brightness of front
panel indicators.
Set brightness as a percentage of the maximum.
100% [>> 100%]
*75% [>> 75%]
50% [>> 50%]
ALARM [> ALARM]: Determine whether alarm messages are OFF [>> OFF]: Alarm messages are not issued.
issued or not.
*ON [>> ON]: Alarm messages are issued.
REF ALARM [> REF ALARM]: Determine whether alarm
messages related to reference video signal are issued or
not.
OFF [>> OFF]: Alarm messages are not issued.
*ON (LIMITED) [>> ON (Limit)]: Alarm messages are issued
only during recording mode, EE mode, and while editing.
ON [>> ON]: Alarm messages are issued.
TIME CODE [Time code]: Settings related to the time code Description of settings
generator
Chapter 4 Menu Settings
TC MODE [> TC mode]: Determine the time code to use:
*INT PRESET [>> PRESET]: Use internal time code with a
internal time code using a preset initial value, regenerated
preset initial value.
internal time code (locked to time code read from tape), or INT REGEN [>> REGEN]: Use internal time code locked to
external time code.
time code read from tape.
EXT REGEN [>> EXT]: Use external time code selected as
follows.
• When TC is selected
External time code input to the TIME CODE IN
connector
• When VITC is selected
The VITC time code present in the input video signal
Note
When the selected input mode is SDTI or i.LINK (the V:SDTI,
SDTI, or i.LINK indicator is lit in the Input selection/audio
mode display section), setting this item to EXT REGEN
causes the internal time code generator to automatically
synchronize with the external time code input to the unit via
the SDTI or i.LINK interface.
RUN MODE [> RUN mode]: Select the advancement (RUN)
mode of the time code generator.
*FREE RUN [>> FREE RUN]: Time code generator keeps
running.
REC RUN [>> REC RUN]: Time code generator only runs
while recording.
Note
Set to FREE RUN when carrying out editing with an editing
control unit. With the REC RUN setting, editing will not be
carried out correctly.
(For DSR-1800 only)
*ON (DF) [>> ON (DF)]: Drop frame mode
DF MODE [> DF mode]: Select whether the time code
OFF (NDF) [>> OFF (NDF)]: Non-drop frame mode
generator and time counter operate in drop frame mode or
non-drop frame mode.
Normally select drop frame mode, to keep in
synchronization with real time. The non-drop frame mode
is useful for example when using computer graphics, and
working on a frame count basis.
60
Menu Contents
TIME CODE [Time code]: Settings related to the time code Description of settings
generator
TC SELECT [>TC select]: Determine which to display in the
time counter display, TC or VITC.
VITC [>> VITC]: Display VITC.
*TC [>> TC]: Display TC.
VITC [> VITC]: Determine whether to record the internally
generated time code as VITC.
OFF [>> OFF]: Do not record the internally generated time
code as VITC. (VITC present in the input video signal is
recorded unchanged.)
*ON [>> ON]: Record the internally generated time code as
VITC.
TCG REGEN [>TCG regen]: Select the signal to be
*TC & UB [>> TC & UB]: Both the time code and user bits are
regenerated when the time code generator is in the
regenerated.
regeneration mode (i.e., when the TC MODE menu item is TC [>> TC]: Only the time code is regenerated.
set to INT REGEN or EXT REGEN).
UB [>> UB]: Only the user bits are regenerated.
*000: NOT SPECIFIED [>> 000]: Character set not specified
001: ISO CHARACTER [>> 001]: 8-bit characters conforming
to ISO 646 and ISO 2022
010: UNASSIGNED-1 [>> 010]: Undefined
Note
011: UNASSIGNED-2 [>> 011]: Undefined
When the TC MODE menu item is set to EXT REGEN, the
user-bit binary group flag setting follows the setting on the time 100: UNASSIGNED-3 [>> 100]: Undefined
101: PAGE/LINE [>> 101]: Multiplex
code input to this unit.
110: UNASSIGNED-4 [>> 110]: Undefined
111: UNASSIGNED-5 [>> 111]: Undefined
UB BINARY GP. [> Binary Gp.]: Select the user bit binary
group flag of the time code generator.
VITC POS SEL-1 [>VITC pos-1]: Select a line to insert the
VITC in.
(For DSR-1800)
12 LINE [>> 12 line] to 20 LINE [>> 20 line]: Select any line
from 12 to 20.
Factory default setting: 16 LINE [>> 16 line]
Note
You can insert the VITC signal in two places. To insert it in two (For DSR-1800P)
places, set both this item and also VITC POS SEL-2.
Select a line to insert the VITC in.
9 LINE [>> 9 line] to 22 LINE [>> 22 line]: Select any line
from 9 to 22.
Factory default setting: 19 LINE [>> 19 line]
(For DSR-1800)
12 LINE [>> 12 line] to 20 LINE [>> 20 line]: Select any line
from 12 to 20.
Factory default setting: 18 LINE [>> 18 line]
Note
You can insert the VITC signal in two places. To insert it in two (For DSR-1800P)
places, set both this item and also VITC POS SEL-1.
Select a line to insert the VITC in.
9 LINE [>> 9 line] to 22 LINE [>> 22 line]: Select any line
from 9 to 22.
Factory default setting: 21 LINE [>> 21 line]
VITC OUTPUT [>VITC out]: Select the time code to be output OFF [>> OFF]: Do not output VITC.
as VITC.
TC [>> TC]: Output TC after converting it into VITC.
*VITC [>> VITC]: Output VITC.
EE OUT PHASE [>EE out]: Determine the output phase for
the LTC signal output from the TIME CODE OUT
connector when recording time code and in STOP REC
mode (forced EE mode).
*MUTE [>>mute]: Mute the output.
THROUGH [>> through]: Output the time code input to the
TIME CODE IN connector as it is. (See example
configuration on page 67.)
VIDEO INPUT PHASE [>> V input]: Output the time code
with the same phase as the input video signal phase.
(See example configuration on page 67.)
VIDEO OUTPUT PHASE [>> V output]: Output the time code
with the same phase as the output video signal phase.
(See example configuration on page 68.)
MUTE IN SRCH [>Mute in SR]: Select whether to mute the
output from the TIME CODE OUT connector in search
(jog/shuttle) mode.
OFF [>> OFF]: Do not mute.
*ON [>> ON]: Mute.
Menu Contents
Chapter 4 Menu Settings
VITC POS SEL-2 [>VITC pos-2]: Select a line to insert the
VITC in.
61
TAPE PROTECTION [Tape protct]: Settings related to tape
and video head protection
Description of settings
FROM STOP [> From STOP]:
STOP TIMER [>> STP
Set the time to switch from
timer]: Set the time to
stop mode to tape protection
switch from stop mode
mode.
to tape protection
mode.
5 MIN [>>> 5 min] to 0.5 SEC [>>> 0.5 sec]: Select time from
12 settings ranging from 0.5 second to 5 minutes in steps
of 0.1 second.
Factory default setting: 1MIN [>>> 1min]
FROM STILL [> From STILL]:
Set the time to switch from
still search mode to tape
protection mode. Also select
the type of tape protection
mode.
STILL TIMER [>> STL
5 MIN [>>> 5 min] to 0.5 SEC [>>> 0.5 sec]: Select time from
timer]: Set the time to
12 settings ranging from 0.5 second to 5 minutes in steps
switch from still search
of 0.1 second.
mode to tape
Factory default setting: 1MIN [>>> 1min]
protection mode.
NEXT MODE [>> Next
*STEP FWD [>>> Step]: The tape is advanced at 1/30 times
mode]: Select the type
normal speed for about 2 seconds.
of tape protection
STANDBY OFF [>>> STANDBY]: Standby off mode
mode to follow still
search mode when the
time set with the STILL
TIMER menu item
elapses.
VIDEO CONTROL [Video]: Settings related to video control Description of settings
EE DELAY [>EE delay]: An E-E video signal is output delayed *SYNC DELAY [>> sync]: Delay the sync signal by the
with respect to the video input signal by the time for video
corresponding amount of time before attaching it.
circuit processing. With this item, select whether or not to VIDEO DELAY [>> video]: Attach a sync signal with the same
delay the sync signal attached to the output video signal by
timing as the input signal.
an amount corresponding to the video signal delay.
INT VIDEO SG [>Video SG]: Select the test signal to be
*75% COLOR BARS [>>75% bars]: 75% color bar signal
output from the internal test signal generator. When SG is BLACK BURST [>>BB]: Black burst signal
selected using the VIDEO IN button, the internal test signal
generator outputs the selected test signal. This signal can
be recorded.
Chapter 4 Menu Settings
STD/NON-STD [>STD/N-STD]: Select the STD or NON-STD
mode in accordance with the composite video or S-video
input.
*FORCED STD [>> STD]: The STD mode is always used
(forced STD mode).
FORCED NON-STD [>> NON-STD]: Use this setting when
the input video signal is unstable (forced NON-STD
mode).
OUT REF SEL [>Out Ref.]: Select the reference video signal
to use.
*REF VIDEO [>> REF]: Use the signal input to a REF. VIDEO
IN connector as the reference video signal. The input
video signal to be edited is required to be in
synchronization with the reference video signal.
INPUT VIDEO [>> INPUT]: Use the input video signal
selected with the VIDEO IN button in the INPUT SELECT
section.
(For DSR-1800 only)
*OFF [>> OFF]: Do not remove black setup.
SETUP REMOVE [> Setup rmv]: Determine whether or not to ON (REMOVE) [>> ON]: Remove black setup.
remove black setup (7.5 IRE) from input analog video
signals when converting them into digital signals.
62
(For DSR-1800 only)
SETUP ADD [> Setup add]: Determine whether or not to add
black setup to analog video output signals.
*OFF [>> OFF]: Do not add black setup.
ON (ADD) [>> ON]: Add black setup.
(For DSR-1800 only)
CC(F1) BLANK [>CC1 blank]: Select whether to mute the
closed caption signal to be superimposed on the 1st field
of the output video signal.
*OFF [>> OFF]: Do not mute.
ON [>> ON]: Mute.
(For DSR-1800 only)
CC(F2) BLANK [>CC2 blank]: Select whether to mute the
closed caption signal to be superimposed on the 2nd field
of the output video signal.
*OFF [>> OFF]: Do not mute.
ON [>> ON]: Mute.
Menu Contents
VIDEO CONTROL [Video]: Settings related to video control Description of settings
WIDE MODE [>Wide mode]: Determine whether to retain
wide-screen aspect ratio information accompanying video
being recorded or played back.
*AUTO [>> Auto]: When video being recorded or played back
is accompanied by wide-screen aspect ratio information,
retain the information.
OFF [>> OFF]: Ignore wide-screen aspect ratio information.
ON [>> ON]: Whenever recording or playing back video, retain
wide-screen aspect ratio information.
ESR MODE [>ESR mode]: Select whether to enable the edge *OFF [>> OFF]: Do not enable.
subcarrier reducer (ESR).
ON [>> ON]: Enable.
When playing back a composite signal, set this to ON.
PROCESS CONTROL [>Proc
ctrl]
CONTROL DEV [>>Ctrl
dev]: Select the
method of controlling
the internal digital
video processor.
*REMOTE [>>>REMOTE]: Use the optional UVR-60/60P or
BVR-50/50P Remote Control Unit to remote control the
internal digital video processor.
MENU [>>> MENU]: Use the setup menu to change the
settings for the internal digital video processor.
C PHASE MODE [>>C
Phas MD]: Select the
phase rotation mode
for chroma phase
control.
The effect of this setting
applies to the output levels
of all of the composite
video, S video, SDI and
component video signals.
*U/V (COMPOSITE) [>>> Cmpst]: Select this setting when
observing the composite video output level using a
composite vectorscope.
PB/PR (COMPONENT) [>>> Cmpnt]: Select this setting
when observing the component video output level using a
component vectorscope.
ADJ RANGE [>>Adj
range]: Select the
variable range of the
VIDEO and CHROMA
gains.
*−
−3 to +3 (dB) [>>> −3/+
+3]: −3 dB to +3 dB
WIDE [>>> wide]: −∞ to +3 dB
VIDEO GAIN [>>V gain]:
00H to 3FFH
Adjust the video output Factory default setting: 200H
level.
00H to 3FFH
Factory default setting: 200H
CHROMA PHASE [>>C
phase]: Adjust the
chroma phase.
00H to FFH
Factory default setting: 80H
(For DSR-1800 only)
SETUP LEVEL [>>Setup
lev]: Adjust the black
setup level.
00H to 3FFH
Factory default setting: 200H
(For DSR-1800P only)
BLACK LEVEL [>>Black
lev]: Adjust the black
level.
00H to 3FFH
Factory default setting: 200H
LINE 335 [>>Line 335]:
Switch blanking on or
off for the 335th line of
the input video signal.
BLANK [>>> blank]: Blank.
THROUGH [>>> through]: Do not blank.
Chapter 4 Menu Settings
(For DSR-1800P only)
INPUT BLANK [>Input blnk]
CHROMA GAIN [>>C
gain]: Adjust the
chroma output level.
AUDIO CONTROL [Audio]: Settings related to audio
control
Description of settings
REC MODE [>REC mode]: Select the audio recording mode.
*2CHANNEL (48kHz) [>> 2 ch]: 2-channel, 48-kHz mode
4CHANNEL (32kHz) [>> 4 ch]: 4-channel, 32-kHz mode
Menu Contents
63
AUDIO CONTROL [Audio]: Settings related to audio
control
Description of settings
INPUT ARRANGE [>Input arng]: Make settings for input
audio mixing.
Make settings using the arrow buttons (KkJj) to move the
cursor and the SET (YES) button to toggle the setting on and
off.
AUDIO INPUT SOURCE
ARRANGE
1
in1 in2 in3 in4
ch1:*on
ch2:
on
ch3:
ch4
2
on
@ @on
on
ON/OFF :
TO MENU :
3
SET KEY
MENU KEY
4
1 Input audio channel 1 (“in1”) is recorded on audio channel 1
(“ch1”) on tape.
2 Input audio channels 2 and 4 (“in2” and “in4”) are recorded
mixed on audio channel 2 (“ch2”) on tape.
3 Input audio channel 4 (“in4”) is recorded on audio channel 3
(“ch3”) on tape.
4 Input audio channel 3 (“in3”) is recorded on audio channel 4
(“ch4”) on tape.
*VARIABLE [>> Variable]: Enable.
PRESET [>> Preset]: Disable.
LEVEL SELECT [>Level Sel]
REF LEVEL [>>REF
Level]: Select the
audio reference level
(headroom) for
recording on tape.
*−
−20 dB [>>> −20dB] (factory default setting for DSR-1800)
*−
−18 dB [>>> −18dB] (factory default setting for DSR-1800P)
−16 dB [>>> −16dB]
−12 dB [>>> −12dB]
CH1 IN LEVEL [>>CH1
input]: Select the
audio level setting
according to the audio
level of the signal input
to the AUDIO IN CH-1
connector.
*+
+4 dBm [>>> +4dBm]
0 dBm [>>> 0dBm]
−3 dBm [>>> −3dBm] (for DSR-1800P only)
−6 dBm [>>> −6dBm]
CH2 IN LEVEL [>>CH2
input]: Select the
audio level setting
according to the audio
level of the signal input
to the AUDIO IN CH-2
connector.
*+
+4 dBm [>>> +4dBm]
0 dBm [>>> 0dBm]
−3 dBm [>>> −3dBm] (for DSR-1800P only)
−6 dBm [>>> −6dBm]
CH3 IN LEVEL [>>CH3
input]: Select the
audio level setting
according to the audio
level of the signal input
to the AUDIO IN CH-3
connector.
*+
+4 dBm [>>> +4dBm]
0 dBm [>>> 0dBm]
−3 dBm [>>> −3dBm] (for DSR-1800P only)
−6 dBm [>>> −6dBm]
CH4 IN LEVEL [>>CH4
input]: Select the
audio level setting
according to the audio
level of the signal input
to the AUDIO IN CH-4
connector.
*+
+4 dBm [>>> +4dBm]
0 dBm [>>> 0dBm]
−3 dBm [>>> −3dBm] (for DSR-1800P only)
−6 dBm [>>> −6dBm]
OUTPUT LEVEL [>>Out
Level]: Select the
analog audio output
reference level.
*+
+4 dBm [>>> +4dBm]
0 dBm [>>> 0dBm]
−3 dBm [>>> −3dBm] (for DSR-1800P only)
−6 dBm [>>> −6dBm]
Chapter 4 Menu Settings
REC LEVEL [>Rec level]: Determine whether to enable or
disable the AUDIO INPUT LEVEL control knobs on the
front panel.
64
Menu Contents
AUDIO CONTROL [Audio]: Settings related to audio
control
Description of settings
INT AUDIO SG [>Audio SG]: Select the operation of the
internal audio test signal generator.
SILENCE [>> silence]: Silent signal
*1kHz SINE [>> 1kHz]: 1-kHz, −20 dB FS sine wave signal
When you select SG as the audio input in the INPUT SELECT
section on the front panel, the audio test signal generated by
the internal audio test signal generator is input.
OUTPUT CH3/4 [>OUT ch3/4]: Select the signals to be output *LINE OUT [>> line out]: Output the audio channel-3 and
from the AUDIO OUT CH-3 and AUDIO OUT CH-4
audio channel-4 signals from the AUDIO OUT CH-3 and
connectors.
AUDIO OUT CH-4 connectors as they are.
MONITOR OUT [>> monitor]: Output the monitor audio Lchannel (CH-1) and monitor audio R-channel (CH-2)
signals from the AUDIO OUT CH-3 and AUDIO OUT CH4 connectors, respectively.
OUTPUT PHASE [>Out phase]: Select the audio playback
signal output timing.
AUDIO OUTPUT PHASE: 0 to FF (Select in this range.)
The reference position corresponds to a setting of 80H. When
a value smaller than 80H is selected, the output timing is
advanced, and when a value larger than 80H is selected, the
output timing is delayed. (80H = 128 samples = approx. 2.7
ms, 1 sample = approx. 20 µs)
Factory default setting: 80H
JOG CONTROL [> Jog ctrl]: Select whether to adjust the
audio playback speed during slow playback.
OFF [>> OFF]: Do not adjust the audio playback speed.
*ON [>> ON]: Adjust the audio playback speed.
SHUTTLE MUTE [>Shutl mute]: Set the audio muting
conditions during shuttle playback.
*OFF [>> OFF]: Not muted.
CUEUP or PREROLL [>> CUEUP]: Muted during cue-up or
preroll operations.
FULL [>> FULL]: Muted in shuttle mode.
AUDIO EDIT [>Audio edit]: Specify the type of editing for
audio signals.
CUT EDIT [>> Cut edit]: Cut editing (Discontinuity in audio
signal may result at the editing point, causing noise during
playback.)
*CROSS FADE [>> Cross]: Cross-fade
Chapter 4 Menu Settings
IN/OUT
FADE IN/OUT [>> Fade]: Fade in and fade out
IN
OUT
DV PB ATT [>DV PB ATT]: When playing back a tape
recorded in consumer DV format, select whether to
attenuate the audio output level.
OFF [>> OFF]: Do not attenuate.
*ON [>> ON]: Attenuate.
DIGITAL PROCESS [Digi. proc]: Settings related to digital
process
Description of settings
SYSTEM EE MODE [>System EE]: Select the bypass E-E
mode or system E-E mode.
*OFF [>> OFF]: Bypass E-E (ordinary setting)
ON [>> ON]: System E-E
Menu Contents
65
SETUP BANK OPERATION [Setup Bank]: Settings related
to menu bank operations
Description of settings
RECALL BANK1 [>Recall 1]: Recall menu settings from
menu bank 1.
(1) Select the bank you want to recall, then press the k
button.
Message “RECALL OK?” appears.
(2) To recall, press the SET (YES) button.
To quit recalling, press the RESET (NO) button.
RECALL BANK2 [>Recall 2]: Recall menu settings from
menu bank 2.
RECALL BANK3 [>Recall 3]: Recall menu settings from
menu bank 3.
RECALL BANK4 [>Recall 4]: Recall menu settings from
menu bank 4.
SAVE BANK 1 [>Save 1]: Save current menu settings to menu (1) Select the bank you want to save, then press the k
bank 1.
button.
Message “SAVE OK?” appears.
SAVE BANK 2 [>Save 2]: Save current menu settings to menu
(2) To save, press the SET (YES) button.
bank 2.
To quit saving, press the RESET (NO) button.
SAVE BANK 3 [>Save 3]: Save current menu settings to menu
bank 3.
SAVE BANK 4 [>Save 4]: Save current menu settings to menu
bank 4.
Menu banks
This unit allows four different complete sets of menu settings to be saved in what are termed “menu banks” numbered 1 to 4.
Saved sets of menu settings can be recalled for use as required.
MENU GRADE [Menu grade]: Selection of menu items to
be displayed
Description of settings
Determine whether to display basic items only or both basic
and enhanced items on the monitor screen and in the time
counter display when using the menu.
*BASIC [> Basic]: Display basic items only.
ENHANCED [> Enhanced]: Display both basic and enhanced
items.
Chapter 4 Menu Settings
66
Menu Contents
EE OUT PHASE settings for time code
output
Use the following as reference information when setting
the EE OUT PHASE menu item (see page 61).
• THROUGH mode
In this mode, the LTC signal is output with the phase
synchronized with the input time code signal. This mode
is appropriate when recording signals from multiple
devices on a number of VCRs.
When the camcorder is in genlock mode, the time code
precision is ±0 frames. When the camcorder is not in
genlock mode, it is ±1 frame.
• VIDEO INPUT PHASE mode
The time code output signal is synchronized with the
input video signal.
This mode is appropriate when the output from a single
device is recorded on a number of VCRs. The
connections are loop-through connections.
In this mode, the same time code is recorded on all of the
VCRs 1 to n.
VIDEO OUT
VIDEO IN
VIDEO LOOP THRU
TIME CODE IN
TIME CODE OUT
VIDEO IN
Output device
(VCR, camera, etc.)
AUDIO IN
VIDEO IN
TIME CODE IN
Camcorder 1
DSR-1800/1800P (1st unit)
VIDEO LOOP THRU
TIME CODE OUT
TIME CODE IN
DSR-1800/1800P (1st unit)
TIME CODE OUT
DSR-1800/1800P (2nd unit)
VIDEO IN
AUDIO IN
TIME CODE IN
Camcorder 2
TIME CODE OUT
DSR-1800/1800P (2nd unit)
VIDEO IN
VIDEO LOOP THRU
TIME CODE OUT
DSR-1800/1800P (nth unit)
VIDEO IN
Camcorder n
AUDIO IN
Composite video or SDI (video and audio) signal
TIME CODE IN
Time code signal
Chapter 4 Menu Settings
TIME CODE IN
TIME CODE OUT
DSR-1800/1800P (nth unit)
Composite video or S-video signal
Audio signal
Time code signal
Menu Contents
67
• VIDEO OUTPUT PHASE mode
The time code output signal is synchronized with the
output video signal.
This mode is appropriate when outputting signals from a
single device to a number of VCRs using separate cables
for video, audio, and time code.
In this mode, the same time code is recorded on all of the
VCRs 1 to n.
VIDEO OUT
VIDEO IN
AUDIO OUT
VIDEO OUT
AUDIO IN
TIME CODE OUT
AUDIO OUT
TIME CODE IN
Output device
(VCR, camera, etc.)
TIME CODE OUT
DSR-1800/1800P (1st unit)
VIDEO IN
VIDEO OUT
AUDIO IN
AUDIO OUT
TIME CODE IN
TIME CODE OUT
DSR-1800/1800P (2nd unit)
Chapter 4 Menu Settings
VIDEO IN
VIDEO OUT
AUDIO IN
AUDIO OUT
TIME CODE IN
TIME CODE OUT
DSR-1800/1800P (nth unit)
•
•
•
•
Composite video signal
S-video signal
Analog component signal
SDI (video and audio) signal
Audio signal
Time code signal
68
Menu Contents
Auto Mode (AUTO FUNCTION) Execution Menu
The following table shows the purpose and function of the
items in the auto mode execution menu.
For details of the use of individual items, see “Digitally
Dubbing Signals in DVCAM Format” on page 50 and
“Rerecording the Time Code—TC Insert Function” on
page 45.
Menu contents
SDTI DUBBING [SDTI DUB]: Selection of data for SDTI
dubbing
Settings
For dubbing through the SDTI (QSDI) interface, select data that A/V [> A/V]: Dub the audio and video.
the dubbing applies to.
A/V/TC [> A/V/TC]: Dub the audio, video, and time code.
A/V/TC/CM [> A/V/TC/CM]: Dub the audio, video, time code,
and cassette memory contents.
Note
When A/V is selected, the time code recorded follows the
setting of the TIME CODE menu items (see page 60) in the
setup menu.
i.LINK DUBBING [i.LINK DUB]: Selection of data for i.LINK
dubbing
Settings
For dubbing through the i.LINK interface, select data that the
dubbing applies to.
A/V [> A/V]: Dub the audio and video.
A/V/TC [> A/V/TC]: Dub the audio, video, and time code.
A/V/TC/CM [> A/V/TC/CM]: Dub the audio, video, time code,
and cassette memory contents.
TC INSERT [TC insert]: Time code rewriting
Settings
Rewrite the time code from an initial value which can be set
freely.
−
Menu Contents
Chapter 4 Menu Settings
Note
When A/V is selected, the time code recorded follows the
setting of the TIME CODE menu items (see page 60) in the
setup menu.
69
Changing Menu Settings
This section explains how to change menu settings.
Changing the Settings of Basic
Items
The factory default setting is to display only the basic
items. To change the settings of basic items proceed as
follows.
Buttons Used to Change Settings
1
3,5,7
2,4,6
Use the following buttons on the menu control panel to
change the menu settings.
Menu control buttons
Functions
MENU button
• Opens the menu and
launches menu control
mode.
• Closes the menu and exits
menu control mode.
J and j buttons
These buttons move the
highlighted cursor up and
down within the current level
to select an item or setting.
Hold down one of these
buttons to make the
highlighted cursor move
continuously.
Chapter 4 Menu Settings
K and k buttons
• Press the k button to go
down one level.
• Press the K button to go
up one level.
Hold down one of these
buttons to make the
highlighted cursor move
continuously.
RESET (NO) button
• Returns the setting to the
factory default setting.
• Sends a negative
response to prompts on
the monitor screen.
SET (YES) button
• Saves the new setting in
memory.
• Sends a positive response
to prompts on the monitor
screen.
A
Changing Menu Settings
9
MARK
8
1
Press the MENU button on the menu control panel.
The menu selection level display appears on the
monitor. In the figure below, “SETUP MENU” is
selected (shown in reverse video).
The time counter display of this unit shows only the
currently selected item. When the item name is long, it
is abbreviated.
Menu selection level display
SYSTEM MENU
SETUP MENU
AUTO FUNCTION
HOURS METER
Monitor screen
70
B
Setup menu
Time counter display
2
With “SETUP MENU” selected, press the k button.
5
This displays all items on menu level 1.
Level-1 menu display
SETUP MENU
OPERATIONAL FUNCTION
DISPLAY CONTROL
TIME CODE
SETUP BANK OPERATION
MENU GRADE
Operational
Time counter display
:BASIC
Monitor screen
3
Press the J or j button to select the required item.
Example: Display when “DISPLAY CONTROL” is selected
SETUP MENU
OPERATIONAL FUNCTION
DISPLAY CONTROL
TIME CODE
SETUP BANK OPERATION
MENU GRADE
Press the J or j button to select the item whose
setting you wish to change.
For menu items on level 3, press the k button to go
to the level 3, then press the J or j button to select the
item whose setting you wish to change.
Example: Display when “BRIGHTNESS” is selected
SETUP MENU
DISPLAY CONTROL
CHARA.DISPLAY :ON
CHARA.POSITION
CHARA.TYPE
:WHITE
CHARA.VSIZE
:x1
DISPLAY INFO
:T&STA
SUB STATUS
:OFF
MENU DISPLAY
:WHITE
PEAK HOLD
:OFF
OVER DISP HOLD :OFF
BRIGHTNESS
:75%
ALARM
:ON
> Brightness
Time counter display
Monitor screen
6
Press the k button.
This displays all possible settings for the item selected
in step 5.
Display
Time counter display
SETUP MENU
DISPLAY CONTROL
BRIGHTNESS
:75%
100%
* 75%
50%
:BASIC
>> 75%
Time counter display
Chapter 4 Menu Settings
Monitor screen
4
Press the k button.
Monitor screen
This displays the menu level 2 for the menu item
selected in step 3.
7
Example: Level-2 display for “DISPLAY CONTROL”
SETUP MENU
DISPLAY CONTROL
CHARA.DISPLAY :ON
CHARA.POSITION
CHARA.TYPE
:WHITE
CHARA.VSIZE
:x1
DISPLAY INFO
:T&STA
SUB STATUS
:OFF
MENU DISPLAY
:WHITE
PEAK HOLD
:OFF
OVER DISP HOLD :OFF
BRIGHTNESS
:75%
ALARM
:ON
> Chara disp
Time counter display
Current settings
Press the J or j button to change the setting of the
item.
SETUP MENU
DISPLAY CONTROL
BRIGHTNESS
:75%
100%
* 75%
50%
>> 50%
Time counter display
Monitor screen
Monitor screen
8
To change other settings, press the K button to return
to the previous screen, then repeat steps 5 to 7 as
required.
Changing Menu Settings
71
9
When you have completed the settings, press the SET
(YES) button.
Displaying Enhanced Items
The message “NOW SAVING...” appears on the
monitor screen, and “Saving...” appears in the time
counter display, while the new settings are saved in
memory.
When the saving operation is completed, the monitor
screen and time counter display return to their normal
indications.
The factory default setting is not to display enhanced
items.
To display enhanced items, set the MENU GRADE menu
item (see page 66) to ENHANCED, following the
procedure in the previous section “Changing the Settings
of Basic Items.” (In step 3, first select “MENU GRADE,”
and next select “ENHANCED,” then press the SET (YES)
button to save the setting in memory.)
With this done, when you press the MENU button and the
k button to display the setup menu, all basic and
enhanced items in the menu level 1 appear.
Notes
• If you power off the unit before saving operation is
completed, settings may be lost. Wait until the
saving is completed before powering off the unit.
• If, instead of pressing the SET (YES) button, you
press the MENU button, the new settings are not
saved. The message “ABORT!” appears on the
monitor screen and “Abort!” in the time counter
display for about 0.5 second, and the system exits
the menus. To change more than one setting, be sure
to press the SET (YES) button after making the
settings.
Changing the Settings of Enhanced
Items
To change the settings of enhanced items, first carry out
the procedure in the previous section “Displaying
Enhanced Items,” then proceed as follows.
Chapter 4 Menu Settings
On-screen indication
Meaning
Right-pointing arrow (k) at
the right of a menu item
See step 1 of the foregoing
operating procedure.
Pressing the k button
switches to the next lower
menu level or to a setting
selection screen.
Left-pointing arrow (K) at
the left of a menu item
See step 4 of the foregoing
operating procedure.
Pressing the K button
returns to the previous
(higher) menu level.
Character string at the right of Current setting of the menu
item.
a menu item
See step 4 of the foregoing
• When shown with a colon
operating procedure.
(:): the current setting is
the same as the factory
default setting.
• When shown with a raised
dot (•): the current setting
is different from the factory
default setting.
See step 2 of the operating
procedure in “Changing the
Settings of Enhanced Items”
on page 72.
An asterisk in a complete list
of settings
See step 6 of the foregoing
operating procedure.
Factory default setting.
2
1
Meanings of indications on the monitor
screen
A
B
MARK
4
3
1
Press the MENU button on the menu control panel.
The menu selection level display appears on the
monitor.
2
With “SETUP MENU” selected, press the k button.
This displays all basic and enhanced items on menu
level 1.
Level-1 menu display
SETUP MENU
OPERATIONAL FUNCTION
DISPLAY CONTROL
TIME CODE
TAPE PROTECTION
VIDEO CONTROL
AUDIO CONTROL
DIGITAL PROCESS
SETUP BANK OPERATION
MENU GRADE
Menu grade
Time counter display
ENHAN
Current setting
Monitor screen
72
Changing Menu Settings
3
4
Follow the same procedure as in steps 3 to 8 of the
procedure in the section “Changing the Settings of
Basic Items” on page 70 using the arrow buttons to
select an item and change its setting.
When you have completed the settings, press the SET
(YES) button.
The message “NOW SAVING...” appears on the
monitor screen, and “Saving...” appears in the time
counter display, while the new settings are saved in
memory.
When the saving operation is completed, the monitor
screen and time counter display return to their normal
indications.
Returning Menu Settings to Their
Factory Default Settings
4
Press the SET (YES) button.
The message “NOW SAVING...” appears on the
monitor screen, and “Saving...” appears in the time
counter display, while the settings of all items are
returned to their factory default settings. These factory
default settings are saved in memory.
Note
If you power off the unit while settings are being
saved, settings may not be correctly returned to their
factory default settings. Wait until the saving is
completed before powering off the unit.
To abandon the resetting operation
Instead of pressing the SET (YES) button, press the
RESET (NO) button. The display returns to menu
level 1, leaving the settings unchanged.
After making menu setting changes, to return settings to
their factory default settings (setting initialization), use the
following procedure.
To return a particular setting to its factory
default setting
Chapter 4 Menu Settings
In the display for changing the target setting, press the
RESET (NO) button.
Carry out the procedure in the section “Changing the
Settings of Basic Items” on page 70 up to step 6, then with
the current setting displayed (in the example, if the setting
has been changed it will be “100%” or “50%”), press the
RESET (NO) button. The setting returns to its factory
default setting of “75%.”
To return all settings to their factory
default settings
Use the following procedure.
1
Press the MENU button on the menu control panel to
display the menu selection.
2
Press the k button to display level 1 of the setup
menu.
3
Press the RESET (NO) button.
A message appears, to confirm whether or not you
wish to return all settings to their factory default
settings.
Monitor screen
message
“INITIALIZE ALL ITEMS TO
FACTORY PRESET VALUES?”
Message in the time “Init setup?”
counter display
Changing Menu Settings
73
Displaying
Supplementary Status
Information
When you set the SUB STATUS menu item (see page 59)
to other than OFF, you can view supplementary status
information on the monitor screen below the operating
mode display area.
When the SUB STATUS menu item is set to TC MODE:
On-screen
indication
Meaning
INT PRESET FREE
[IP F]
The internal time code generator is
operating in FREE RUN mode.
INT PRESET REC
[IP R]
The internal time code generator is
operating in REC RUN mode.
INT REGEN-T&U
[IRTU]
The internal time code generator is
in synchronization with the playback
time code (LTC) read from tape.
EXT LTC-T&U
[ELTU]
The internal time code generator is
in synchronization with the external
time code (LTC) input to the unit
and is generating the same time
code value and user bit value as
those of the external time code
(regeneration).
EXT VITC-T&U
[EVTU]
The internal time code generator is
in synchronization with VITC
present in the external video signal
input to the unit and is generating
the same time code value and user
bit value as those of the external
time code (regeneration).
EXT QSDI-T&U
[EQTU]
The internal time code generator is
in synchronization with the external
time code input to the unit via SDTI
(QSDI) interface and is generating
the same time code value and user
bit value as those of the external
time code (regeneration).
EXT QSDI.V-T&U
[EQTU]
The internal time code generator is
in synchronization with the external
VITC input to the unit via SDTI
(QSDI) interface and is generating
the same time code value and user
bit value as those of the external
time code (regeneration).
EXT DVIN-T&U
[EDTU]
The internal time code generator is
in synchronization with the external
time code input to the unit via i.LINK
(DV IN) interface and is generating
the same time code value and user
bit value as those of the external
time code (regeneration).
EXT DVIN.V-T&U
[EDTU]
The internal time code generator is
in synchronization with the external
VITC input to the unit via i.LINK (DV
IN) interface and is generating the
same time code value and user bit
value as those of the external time
code (regeneration).
0 0 : 0 4 . 4 7 . 0 7
T C R
P L A Y
I N S
V
L O C K
A 1 2 3 4
T C
Supplementary status information
The following items of supplementary status information
are displayed depending on the setting of the SUB
STATUS menu item.
Chapter 4 Menu Settings
Setting of SUB
STATUS menu item
Items of supplementary
information displayed
EDIT PRESET
Editing mode settings made on the
editing control unit
TC MODE
Operating mode of the internal time
code generator
REMAIN
Remaining capacity of the tape
AUDIO MIXING
Setting for input audio mixing
ALL
All of the above items
The following tables show the on-screen indications of
supplementary information and their meaning.
In each table, the indications given in brackets such as
[ASM] are the indications displayed when the SUB
STATUS menu item is set to ALL.
For the display format when ALL is selected, see page 75.
When the SUB STATUS menu item is set to EDIT PRESET:
74
On-screen indication
Meaning
ASM [ASM]
Assemble editing mode
INS V A1234 TC
[V1234T]
INS: Insert editing mode
V A1234 TC: Channels or
signals selected for
insert editing
V: Video
A1234: Audio 1, 2, 3, 4
TC: Time code
Displaying Supplementary Status Information
When the SUB STATUS menu item is set to REMAIN:
On-screen
indication
Meaning
REMAIN 184 min
Remaining capacity of the tape in
minutes.
When the remaining capacity has
not been detected, “REMAIN --min” appears.
When the SUB STATUS menu item is set to AUDIO
MIXING:
On-screen indication
Meaning
1234
[MIX]
Input audio channels
selected for mixing
1234: Input audio channels
1, 2, 3 and 4
Example display:
12
2
3
34
Input audio channels 3 and
4 are mixed and recorded
on audio channel 4 on tape.
Input audio channel 3 is recorded
on audio channel 3 on tape.
Input audio channel 2 is recorded
on audio channel 2 on tape.
Input audio channels 1 and 2 are mixed and
recorded on audio channel 1 on tape.
Display format of supplementary status
information when the SUB STATUS menu item is
set to ALL
All items of supplementary status information are
displayed in the order shown below.
Chapter 4 Menu Settings
T C R
0 0 : 0 4 : 4 7 . 0 7
P L A Y
V 1 2 3 4 T
Editing mode settings
L O C K
M I X
E D T U V
Operating mode of the internal
time code generator
(The rightmost “V” appears
when the VITC menu items
(see page 61) is set to ON.)
Setting for input audio mixing
Displaying Supplementary Status Information
75
Chapter 4 Menu Settings
76
Displaying Supplementary Status Information
Connections and
Settings
Chapter
5
Connections for a Digital Non-Linear Editing System
This unit can be connected to an ES-7 EditStation to
configure a digital non-linear editing system.
If you use the SDTI (QSDI) interface with the optional
DSBK-1802 board installed in the unit, you can transfer
video, audio, time code, and other compressed data
between this unit and the ES-7.
The unit supports ClipLink functions, enabling index
pictures recorded on tape and ClipLink log data stored in
cassette memory to be transferred to the ES-7 in an instant.
For a general description of ClipLink functions, see the
appendix “ClipLink Guide” (page 104).
The following figure shows a connection diagram for a
non-linear editing system in which this unit serves as the
recorder.
For connections of the ES-7 and its peripheral devices
such as the ESBK-7011 Control Panel, the ESBK-7045
Disk Unit, etc., refer to your ES-7 Operating Instructions.
Note
The example connections shown in this chapter assume
that DSR-1600/1600P and DSR-1800/1800P units have
the optional DSBK-1801, DSBK-1802, and DSBK-1803
boards installed as required.
Connections for a Digital Non-Linear Editing System
77
REF.
VIDEO
IN
SDTI(QSDI)
IN
SDTI(QSDI)OUT
REMOTE
VIDEO OUT 2
(SUPER)
DSR-1800/1800P
(recorder)
Composite
video input
1
1
B B OUT(1/2/3/4)
1
QSDI OUTPUT
1
QSDI INPUT
2
RECORDER
AUDIO
MONITOR OUT
ES-7 EditStation
3
Audio input
A 75 Ω coaxial cable (not supplied)
B 9-pin remote control cable
(not supplied)
C Cable with RCA phono plugs
(not supplied)
Video monitor
Settings on the DSR-1800/1800P
Button
Setting
REMOTE
On (lit)
For details of video/audio input and audio mode settings,
see “Settings for Recording” on page 25.
Chapter 5 Connections and Settings
78
Connections for a Digital Non-Linear Editing System
Connections for a Cut Editing System
The following figure shows a cut editing system
configuration that includes two DSR-1800/1800P units to
serve as the player and recorder.
When using a VCR other than the DSR-1800/1800P, refer
to its instruction manual.
When you select assemble or insert editing mode on
the editing control unit, the two DSR-1800/1800P
units (recorder and player) will automatically enter the
selected editing mode.
A 75 Ω coaxial cable (not supplied)
B 9-pin remote control cable
(not supplied)
C Cable with RCA phono plugs
(not supplied)
1
DSR-1800/1800P
(player)
DSR-1800/1800P
(recorder)
SDTI(QSDI)IN
SDTI(QSDI)OUT
REF.
VIDEO
OUT
VIDEO
OUT 2
(SUPER)
AUDIO
MONITOR
OUT
REMOTE
3
2
1
Composite
video input
VIDEO
OUT 2
(SUPER)
AUDIO
MONITOR
OUT
REMOTE
1
3
2
Composite
video input
Audio input
1
Audio input
PLAYER
REF.
VIDEO IN
Main monitor
RECORDER
Editing control unit (RM-450/
450CE, PVE-500, etc.) a)
Settings on the DSR-1800/1800Ps (recorder and
player)
Button
Recorder
Player
REMOTE
On (lit)
On (lit)
9PIN
On (lit)
On (lit)
a) For the settings on the editing control unit, see
“Settings on an editing control unit” on page
85.
About reference video signals
In order to provide stable video and audio signals for
analog editing, it is necessary for the built-in time base
corrector (TBC) to operate correctly. To ensure this, input
a reference video signal synchronized with the video signal
to the REF. VIDEO IN connector.
Chapter 5 Connections and Settings
Source monitor
For details of the video/audio input and audio mode
settings for the recorder, see “Settings for Recording” on
page 25.
Connections for a Cut Editing System
79
Connections for an A/B Roll Editing System
The following is an example configuration of A/B roll
editing system using the DSR-1800/1800P.
In this configuration, the recorder is a DSR-1800/1800P
unit, player 1 is a DSR-1600/1600P unit, and player 2 is an
analog Betacam UVW-1600/1600P Videocassette Player
unit. To create a final tape (a tape that contains a
completely packaged program) in Betacam format, use a
Betacam VCR such as the UVW-1800/1800P as the
recorder.
The purpose of the following figure is to clearly indicate
the flow of signals among the component devices in this
system. The specific connections and settings are
described beginning on page 82.
Chapter 5 Connections and Settings
80
Connections for an A/B Roll Editing System
Main video monitor
Source video monitor
Audio system monitor
Video signal generator
(Sony Tektronix TSG130, etc.)
DSR-1800/1800P
(recorder)
DPS-D7 or other delay
unit a)
MXP-290 Audio
Mixer
PVE-500, etc. (editing control unit)
DFS-500/500P
DME Switcher
UVW-1600/1600P
(player 2)
Video signal
Audio signal
Reference video signal
Chapter 5 Connections and Settings
DSR-1600/1600P (player 1)
Control signal
a) When using a DFS-500/500P DME Switcher, the phase of the video signals processed by
the DFS-500/500P is delayed. It is therefore necessary to connect a delay unit between the
MXP-290 Audio Mixer’s output and the audio input to the DSR-1800/1800P (recorder).
Connections for an A/B Roll Editing System
81
Audio monitor system connections
Reference video signal connection
The following shows an example of audio monitor system
connections.
When you perform recording, be sure to input a reference
video signal.
For details of these connections, refer to the instruction
manual for each connected device.
For details of reference video signals, see “About
reference video signals” on page 79.
Speaker (right channel)
Speaker (left channel)
DFS-500/500P DME Switcher
BLACK
BURST
OUT
4 3 2 1
Audio amplifier
REF. VIDEO IN
L
R
L
DSR-1800/1800P
(recorder)
R
Cables with RCA phono plugs
MONITOR
OUT 2
MONITOR
OUT 1
DSR-1600/1600P
(player 1)
REF. VIDEO IN
MXP-290 Audio Mixer
Chapter 5 Connections and Settings
REF. VIDEO IN 75 Ω
termination switch: ON
REF. VIDEO IN
REF.
VIDEO
IN
UVW-1600/1600P
(player 2)
PVE-500 Editing Control Unit
REF. VIDEO IN 75 Ω termination switch: ON
Use 75 Ω coaxial cables for all of these connections.
82
Connections for an A/B Roll Editing System
Control signal connections
The following shows an example of control signal
connections to enable the editing control unit to control all
other A/B roll editing system devices.
DSR-1800/1800P (recorder)
REMOTE
9-pin remote control cable a)
DSR-1600/1600P (player 1)
REMOTE
Mixer control mode
selection switch:
PARALLEL
RECORDER
UVW-1600/1600P (player 2)
PVE-500 Editing
Control Unit
PLAYER 1
MIXER
SWITCHER
PLAYER 2
REMOTE
DFS-500/500P DME Switcher
9-pin remote control cable a)
EDITOR
Chapter 5 Connections and Settings
9-pin remote control cable
a)
MXP-290 Audio Mixer
9-pin/15-pin mixer control cable (not supplied)
EDITOR (15-pin)
a) For the 9-pin remote control cable, use an optional
RCC-5G/10G/30G cable.
Connections for an A/B Roll Editing System
83
Video/audio signal connections
In this example, analog component signals are used as the
video signals and XLR 3-pin connectors are used as audio
input/output connectors.
The following shows an example of video/audio signal
connections in an A/B roll editing system.
DSR-1800/1800P COMPONENT VIDEO IN
(recorder)
Y, R–Y, B–Y
1
VIDEO INPUTS
COMPONENT 2
DFS-500/500P DME Switcher
PGM OUT
COMPONENT 1
CH-2
AUDIO IN
CH-1
3
3
CH-1 OUT
1 VIDEO INPUTS
COMPONENT 1
CH-2 OUT
2
DSR-1600/1600P COMPONENT VIDEO OUT
(player 1)
Y, R–Y, B–Y
DPS-D7 or other delay unit
3 CH-1 IN
CH-2 IN
3
LINE OUT 2
LINE OUT 1
MXP-290
Audio Mixer
MIC/LINE 4
IN
3 2
1
3
CH-2
3
3
3
COMPONENT 1
OUTPUT
Chapter 5 Connections and Settings
A 12-pin/3-BNC cross cable
(not supplied; consult your
Sony dealer about this cable.)
B 12-pin dubbing cable
(not supplied)
UVW-1600/1600P (player 2)
AUDIO OUTPUT
CH-1
CH-2
C Cable with XLR
connectors (not supplied)
Settings on the DSR-1800/1800P (recorder)
84
AUDIO OUT
CH-1
Switch/menu
Setting
AUDIO IN LEVEL/600 Ω
switches
HIGH-ON
LEVEL SELECT menu item
Normally +4 dBm (see page
64)
Connections for an A/B Roll Editing System
For details of the video/audio input and audio mode
settings, see “Settings for Recording” on page 25.
Connection of a video monitor
Settings on an editing control unit
Set up the following connections to enable monitoring of
video and audio signals on a video monitor. In addition to
the video and audio signals, you can have time data, the
operation mode of the unit, alarm messages, and other
information displayed as text on the monitor screen by
setting the CHARA. DISPLAY menu item (see page 59)
to ON (factory default setting).
When connecting an editing control unit, make the settings
as follows, according to the model.
PVE-500
No settings are required.
BVE-600/900/910/2000 (NTSC model) or FXE-100/
120
Set the VCR constants as follows.
1
75 Ω termination switch: ON (or attach a 75
Ω terminator)
Input switches: Set according to the type of
input signals.
Video monitor
2
3
4
5
6
7
8
9
10 11 12 13 14 15
80 15 00 96 05 05 03 80 0A 08 FE 00 80 5A FF
BVE-600/900/910/2000 (PAL model) or FXE-100P/
120P
Set the VCR constants as follows.
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15
81 15 00 7D 05 05 02 80 0A 07 FE 00 80 4C FF
RM-450/RM-450CE
Set the DIP switches as follows.
• Left switches
Composite
video input
2
Audio input
1
VIDEO
OUT
2(SUPER)
AUDIO
MONITOR OUT
7
6
5
4
3
2
1
0
OFF
−
−
OFF
−
−
−
−
• Right switches (RM-450)
)
7
6
5
4
3
2
1
0
OFF
−
OFF
ON
OFF
OFF
ON
ON
• Right switches (RM-450CE)
DSR-1800/1800P (recorder)
B 75 Ω coaxial cable
(not supplied)
6
5
4
3
2
1
0
−
OFF
ON
OFF
OFF
ON
ON
BVE-800
Set the DIP switches as follows.
• SW2
1
2
3
4
5
6
7
8
ON
OFF
ON
ON
−
ON
ON
−
• SW3 (NTSC model)
1
2
3
4
5
6
7
8
ON
ON
ON
OFF
−
ON
OFF
OFF
• SW3 (PAL model)
1
2
3
4
5
6
7
8
OFF
OFF
OFF
ON
−
ON
OFF
OFF
Connections for an A/B Roll Editing System
Chapter 5 Connections and Settings
A Cable with RCA phono plugs
(not supplied)
7
ON
85
Connections for SDTI (QSDI) Dubbing
The following shows an example of connections for
digitally dubbing SDTI (QSDI) signals (see page 50), with
the DSR-1800/1800P used as the recorder and a DSR1600/1600P unit as the player.
DSR-1600/1600P (player)
REMOTE
SDTI(QSDI)OUT
1
SDTI(QSDI)IN
DSR-1800/1800P
(recorder)
2
REMOTE
VIDEO OUT 2
(SUPER)
1
Composite
video input
Chapter 5 Connections and Settings
86
AUDIO
MONITOR OUT
3
Audio input
A 75 Ω coaxial cable (not supplied)
Video monitor
B 9-pin remote control cable
(not supplied)
C Cable with RCA phono plugs
(not supplied)
Settings on the DSR-1800/1800P (recorder) and
DSR-1600/1600P (player)
Model
Switch/button
Setting
DSR-1800/1800P
(recorder)
REMOTE button
Off (unlit)
9PIN button
On (lit)
DSR-1600/1600P
(player)
REMOTE button
On (lit)
9PIN button
On (lit)
Connections for SDTI (QSDI) Dubbing
Connections for Analog Recording
video signals are analog component signals and the audio
signals are recorded from audio channels 1 and 2.
The following shows connections for a system in which
analog playback signals from another recorder or player
are recorded on a DSR-1800/1800P. In this system, the
Video monitor
A Cable with RCA phono plugs
(not supplied)
B 75 Ω coaxial cable
(not supplied)
C Cable with XLR connectors
(not supplied)
Composite
video input
2
Audio input
2
1
2 a)
REF.
VIDEO
IN
COMPONENT VIDEO OUT
Y,R–Y,B–Y
VIDEO
OUT
2(SUPER)
REF.VIDEO
OUT
AUDIO
MONITOR OUT
COMPONENT
VIDEO IN
Y,R–Y,B–Y
AUDIO OUT
CH-1
DSR-1600/1600P (player)
CH-2
DSR-1800/1800P (recorder)
CH-2
3
3
a) Three 75 Ω coaxial cables are used,
one each for Y, R−Y, and B−Y.
Settings on the DSR-1800/1800P (recorder)
Switch/menu/input/audio
mode a)
Setting
AUDIO IN LEVEL/600 Ω
switches
HIGH-ON
LEVEL SELECT menu item
Normally +4 dBm (see page
64)
REMOTE button
Off (unlit)
Video input
Component
Audio input
Analog
Audio mode
2 channel/48 kHz
Chapter 5 Connections and Settings
AUDIO IN
CH-1
a) For details of the video/audio input and audio mode settings, see “Settings
for Recording” on page 25.
Connections for Analog Recording
87
Adjusting the Sync and Subcarrier Phases
After configuring the editing system, use a vectorscope to
adjust the sync and subcarrier phases of the recorder and
players. Subcarrier phase adjustment is necessary when
using composite signals and Y/C signals.
When using two or more players, as in an A/B roll editing
system, it is necessary to synchronize the sync and
subcarrier (for composite signals) phases of the signals to
be edited. If they are not synchronized, picture instabilities
or color break-up may occur at edit points.
DSR-1600/1600P (player 1)
Switcher (DFS-500/500P) a)
DSR-1800/1800P (recorder)
UVW-1600/1600P (player 2)
75 Ω coaxial cable (A) b)
75 Ω coaxial cable (B) b)
Vectorscope (Sony Tektronix
1750/1751, etc.)
PVE-500 Editing
Control Unit
Chapter 5 Connections and Settings
88
a) The sync and subcarrier phases of the
output signal from the DFS-500/500P
switcher are automatically adjusted.
b) Ensure that the 75 Ω coaxial cables (A) and
(B) (not supplied) are of the same length.
Adjusting the Sync and Subcarrier Phases
Performing a phase adjustment operation
Note
1
When component signals are used the subcarrier phase
indicator does not appear.
Press the SCH button on the vectorscope.
The vectorscope switches to SCH mode.
2
8
Press the B channel button on the vectorscope.
Output the player 2 signal from the PVE-500, and
repeat steps 6 and 7 to adjust the sync and subcarrier
phases of the output from player 2.
This displays the black burst signal from the switcher.
3
Press the EXT button on the vectorscope.
This switches the vectorscope to external
synchronization mode.
4
Adjust the phase synchronization control on the
vectorscope so that the sync and subcarrier phases are
close to the reference line.
Sync phase
Subcarrier phase
Reference line
Align the sync and subcarrier phases of the black
burst signal to the reference line.
5
Output the player 1 signal from the PVE-500.
6
Press the A channel button on the vectorscope.
7
Chapter 5 Connections and Settings
This displays the sync and subcarrier phases
(composite signals only) of the signal from player 1.
On player 1, adjust the SYNC PHASE and SC PHASE
controls on the menu control panel, using a Phillips
screwdriver, so that the output from player 1 on
channel A is in correct phase alignment with the black
burst signal on channel B.
This indicator
moves as you
turn the SYNC
PHASE control.
This indicator
moves as you
turn the SC
PHASE control.
Adjust the sync and subcarrier phases of the output
signal from player 1.
Adjusting the Sync and Subcarrier Phases
89
Chapter 5 Connections and Settings
90
Adjusting the Sync and Subcarrier Phases
Maintenance and
Troubleshooting
Maintenance
Chapter
6
Regular Checks
Digital hours meter
Condensation
If you move the unit suddenly from a cold to a warm
location, or if you use it in a very humid place, moisture
from the air may condense on the head drum. This is called
condensation, and if a tape is run in this state, the tape may
stick to the drum and can be easily damaged. To lessen the
risk of this occurring, this unit is equipped with a
condensation detection system.
If condensation occurs while the unit is
operating:
The alarm message “MOISTURE HAS BEEN
DETECTED.” appears on the monitor screen, and the
alarm message “HUMID!” in the time counter display. At
the same time the unit ejects the cassette automatically. If
this happens, leave the unit powered on and wait until the
alarm messages disappear.
If the condensation alarm message appears
immediately after powering on:
Leave the unit powered on and wait until the alarm
message disappears. You cannot load a cassette into the
unit while the alarm message is being displayed.
Once the alarm message disappears, the unit is ready for
use.
The digital hours meter keeps cumulative counts of the
total operating time, the head drum rotation time, the tape
transport operating time, and the number of threading/
unthreading operations. These counts can be displayed on
the monitor screen and in the time counter display of this
unit. Use them as guidelines for scheduling maintenance.
In general, consult your Sony dealer about necessary
periodic maintenance checks.
Digital hours meter display modes
The digital hours meter has the following four display
modes.
• T1 (OPERATION) mode
The cumulative total hours during which the unit is
powered on is displayed in 10-hour increments.
• T2 (DRUM ROTATION) mode
The cumulative total hours of drum rotation with tape
threaded is displayed in 10-hour increments.
• T3 (TAPE RUNNING) mode
The cumulative total hours of tape transport operation
for fast forward, rewind, playback, and search (except in
still search mode) is displayed in 10-hour increments.
• CT (THREADING) mode
The cumulative number of tape threading/unthreading
operation pairs is displayed in 10-operation pair
increments.
For all modes except T1 (OPERATION), there are two
types of count: a “trip” count, which is resettable, and the
cumulative total from manufacture, which is unresettable.
Maintenance
91
Displaying the digital hours meter
Use the following procedure.
1
Press the MENU button on the menu control panel.
The menu selection level display appears on the
monitor screen and in the time counter display.
Menu selection level display
SYSTEM MENU
SETUP MENU
AUTO FUNCTION
HOURS METER
Setup menu
Time counter display
Hours meter
Time counter display
Monitor screen
3
HOURS METER
T1
00000 X10 HOURS
T2 0000/00000 X10 HOURS
T3 0000/00000 X10 HOURS
CT 0000/00000 X10 COUNT
The four-digit value to the left of the slash (/) is the
resettable trip count, and the right value is the cumulative
total from manufacture.
Press the j button to select “HOURS METER.”
SYSTEM MENU
SETUP MENU
AUTO FUNCTION
HOURS METER
Resettable trip counts
Unresettable counts
T1:OPERATION
T2:DRUM ROTATION
T3:TAPE RUNNING
CT:THREADING
Monitor screen
2
Digital hours meter indications on the monitor
screen
All four counts (T1, T2, T3, and CT) are indicated on the
monitor screen.
Press the k button.
The cumulative counts by the digital hours meter are
indicated on the monitor screen and in the time counter
display.
Digital hours meter indications in the time
counter display
One of the four indications appears in the time counter
display at a time. Use the J and j buttons on the menu
control panel to change the item displayed.
Initially, only the trip value appears. Hold down the k
button to display also the cumulative total from
manufacture, which will appear to the right of the trip
value and the slash (/).
The following illustrates the digital hours meter
indications in the time counter display in all four display
modes. The right-hand indication for each display mode is
the indication you can view while holding down the k
button on the menu control panel.
T1 (OPERATION) mode:
Oper. 00000
T2 (DRUM ROTATION) mode:
Chapter 6 Maintenance and Troubleshooting
92
Drum 0000
0000/00000
T3 (TAPE RUNNING) mode:
Tape 0000
0000/00000
CT (THREADING) mode:
Thread 0000
Maintenance
0000/00000
To end the digital hours meter display
Press the MENU button on the menu control panel.
To reset the trip values
About this operation, consult your Sony dealer.
Head Cleaning
Always use the DVM12CL (mini size) or DV12CL
(standard size) Cleaning Cassette to clean the video and
audio heads. You can run the cleaning cassette for 10
seconds per cleaning operation. Follow the instructions for
the cleaning cassette, as inappropriate use of the cleaning
cassette can damage the heads.
To clean the heads
Insert the cleaning cassette. This automatically starts
cleaning. You cannot operate any tape transport control
buttons other than the EJECT button during the cleaning
operation.
After about 10 seconds, the cleaning cassette will be
automatically ejected.
Chapter 6 Maintenance and Troubleshooting
Maintenance
93
Troubleshooting
If an alarm message appears on the monitor screen, or if
the unit appears to be malfunctioning, please check the
following before contacting your Sony dealer.
Tape problems
Symptom
Cause
Recording is not
possible.
The cassette’s REC/SAVE switch is set Set the REC/SAVE switch to REC, or use another cassette.
to SAVE. a)
The unit’s tape
transport control
buttons (PLAY, F FWD,
REW, etc.) do not
work.
The REMOTE button is lit and the
LOCAL ENABLE menu item is set to
STOP & EJECT or ALL DISABLE. a)
Press the REMOTE button to turn it off, or change the setting
of the LOCAL ENABLE menu item (see page 57) to ALL
ENABLE.
No cassette is loaded. a)
Insert a cassette (see page 23).
The NOT EDITABLE
indicator on the front
panel lights up.
Remedy
The audio recording mode selected on • When your current purpose is editing, press the REMOTE
this unit does not coincides with that of
button to turn it off and set the unit for the same audio
recording mode as with the tape using the REC. MODE
the loaded tape. a)
menu item (see page 63), then turn on the REMOTE
button again.
• When your current purpose is recording, you can use the
tape currently loaded in the unit.
The recording format of the currently
loaded tape is “DV” or “DVCPRO.” a)
Replace the tape with one recorded in the DVCAM format.
a) In these states, an alarm message appears on the monitor screen and in the
time counter display.
Time data problems
Symptom
Cause
Remedy
Cannot freely set the
initial time data value.
The TC MODE menu item is set to EXT Change the setting of the TC MODE menu item (see page
60) to INT PRESET.
REGEN. a)
CNT is selected as the time data type
to be displayed (the COUNTER time
data type indicator is lit). a)
Press the COUNTER SEL button to make the TC or U-BIT
time data type indicator light up (the CNT value cannot be
set freely).
The REMOTE button is lit and the
LOCAL ENABLE menu item is set to
STOP & EJECT or ALL DISABLE. a)
Press the REMOTE button to turn it off or change the setting
of the LOCAL ENABLE menu item (see page 57) to ALL
ENABLE.
The tape is running,
The MENU button or TC PRESET
but the time data is not button on the menu control panel has
shown in the time
been pressed.
counter display.
Chapter 6 Maintenance and Troubleshooting
94
Press the button once again to exit the menu control mode,
time code preset mode, or digital hours meter display mode.
(In either of the menu control mode and time code preset
mode, the time data is not shown in the time counter display.)
The U-BIT time data type indicator is lit. Press the COUNTER SEL button to make the COUNTER or
TC time data type indicator light up.
a) In these states, an alarm message appears on the monitor screen and in the
time counter display.
Input problem
Symptom
Cause
It is not possible to
No SDTI signal is input to the unit.
record an SDTI (QSDI)
signal.
a) In this state, an alarm message appears on the monitor screen and in the
time counter display.
Troubleshooting
Remedy
a)
Connect an SDTI signal to the SDTI (QSDI) IN connector.
Monitor problems
Symptom
Cause
Remedy
Data is not
superimposed on the
monitor screen.
The CHARA. DISPLAY menu item is
set to OFF.
Set the CHARA. DISPLAY menu item (see page 59) to ON.
The monitor is not connected to the
VIDEO OUT 2 (SUPER) connector of
this unit.
Connect the monitor to the VIDEO OUT 2 (SUPER)
connector. (You must make this connection to display any
type of text on the monitor.)
The image on the
monitor screen is too
bright.
The 75 Ω termination switch for video
input on the monitor is in the OFF
position, or a 75 Ω terminator is not
fitted to its video input connector.
Set the 75 Ω termination switch to ON or connect a
terminator.
The image on the
monitor screen is too
dark.
In a video signal loop-through
connection of video monitors, 75 Ω
termination switches for video input on
monitors other than the loop-end
monitor are in the ON position.
Set the 75 Ω termination switches to OFF on all monitors
other than the loop-end monitor.
Symptom
Cause
Remedy
The AUDIO INPUT
LEVEL control knobs
do not work.
The REC LEVEL menu item is set to
PRESET.
Set the REC LEVEL menu item (see page 64) to VARIABLE.
The image is too dark
when recording a
composite video
signal.
Audio problem
Note
To be able to perform this operation, it is necessary to set the
MENU GRADE menu item (see page 66) to ENHANCED.
Editing restriction
Symptom
Cause
Execution of video
This phenomenon cannot be avoided with an editing system using this unit as the recorder.
editing in insert mode
erases subcode data
(user bit data, etc.)
recorded on tape other
than time code data.
Chapter 6 Maintenance and Troubleshooting
Troubleshooting
95
Error Messages
This unit is provided with a self-diagnostic function that
detects internal abnormalities. When it detects an
abnormality, it outputs an error message to the monitor
screen and indicates an error code in the time counter
display.
Note
To display error messages on the monitor screen, connect
the monitor to the VIDEO OUT 2 (SUPER) connector, and
set the CHARA. DISPLAY menu item (see page 59) to
ON (factory default setting).
ERROR
AN ERROR HAS BEEN
DETECTED. INFORM SERVICE
OF FOLLOWING CODE:
02-603
PRESS EJECT KEY
TO EJECT TAPE.
Error message
Error code
Direction
Error code
Error02-603
Monitor screen
Time counter display
If an error message appears, follow the direction indicated
on the monitor screen.
Alarm Messages
When operating this unit, the unit may sometimes output
alarm messages such as the one shown below to the
monitor screen and the time counter display.
ALARM
REMOTE MODE IS SELECTED
PRESS REMOTE BUTTON
TURNING IT OFF
Cause of
alarm
Direction
REMOTE!
Monitor screen
Chapter 6 Maintenance and Troubleshooting
96
If such an alarm message appears, a connection or
operation error may have been made, or condensation on
heads may have occurred. Follow the direction indicated
on the monitor screen.
Note
To display alarm messages on the monitor screen, it is
necessary for the monitor to be connected to the VIDEO
OUT 2 (SUPER) connector, and set the following menu
items to ON.
• CHARA. DISPLAY (see page 59)
• ALARM (see page 60)
• REF ALARM (see page 60)
Troubleshooting
Time counter display
Alarm messages and associated directions
Alarm message on monitor screen
(Cause)
Direction
A cleaning tape has been inserted.
The tape will automatically be ejected after cleaning is Cleaning Tp
completed.
A non-standard signal is being used for
input video.
Use a standard signal.
VIN NON-STD
A non-standard ref. signal is being used
for REF. VIDEO.
Use a standard signal.
REF NON-STD
Abnormal settings selected in setup
menu.
Correct the setup menu settings. Contact your Sony
dealer if this alarm message appears again after
making corrections.
ILL. SETUP!
Audio mixing mode cannot be changed
during recording.
−
REC mode!
Audio not editable on this tape.
Use a tape recorded in 2-channel/48 kHz or
4-channel/32 kHz mode.
2CH/32kHz!
Use a tape having audio signals recorded in locked
mode.
UNLOCK mode
Audio REC mode selection different from Select the same audio recording mode as that of the
audio on tape.
tape.
Alarm message in time
counter display
Fs 44.1kHz!
A mode err
Audio REC (recording) mode cannot be
changed during recording.
−
REC mode!
Cassette adaptor not usable.
Use a tape without cassette adaptor.
Adaptor!
Counter mode is selected.
Use the COUNTER SEL button to light the TC or UBIT time data type indicator in the display section.
CNT mode!
Input selection cannot be changed in
REC (recording) mode.
−
REC mode!
Input signal does not conform to DVCAM/ −
DV format.
Unknown Sig
Input signal is 625/50. (For DSR-1800)
−
625/50 sig! (For DSR-1800)
Input signal is 525/60. (For DSR-1800P)
−
525/60 sig! (For DSR1800P)
Input video is not detected.
Check the VIDEO display in the input selection/audio No INPUT!
mode display section and supply an appropriate video
signal.
Input video signal does not synchronize
with REF. VIDEO signal.
Use a reference video signal or connect the recorder
REF. VIDEO OUT connector to the player REF.
VIDEO IN connector.
ILL. REF!
Moisture has been detected.
Keep the power on and wait until this alarm message
disappears.
HUMID!
No cassette in VTR.
Load a cassette.
No Cass.!
Rec inhibit mode is selected.
Set the REC INHIBIT menu item (see page 57) to
OFF.
REC INHI.!
Record inhibit plug on the cassette is set Set the REC/SAVE switch on the cassette to REC.
to inhibit.
REC INHI.!
Remote mode is selected.
REMOTE!
Turn off the REMOTE button.
Chapter 6 Maintenance and Troubleshooting
Note
When connecting the recorder REF. VIDEO OUT
connector to the player REF. VIDEO IN connector, set
the STD/NON-STD menu item (see page 62) to
FORCED NON-STD.
Troubleshooting
97
Alarm messages and associated directions
Alarm message on monitor screen
(Cause)
Direction
Alarm message in time
counter display
Tape cannot be replayed.
Use a tape recorded in 525/60 format. (For DSR1800)
625/50 Tape (For DSR1800)
Use a tape recorded in 625/50 format. (For DSR1800P)
525/60 Tape (For DSR1800P)
Tape end has been detected.
Use a new cleaning tape.
Tape end!
Tape not editable.
Use a tape recorded in DVCAM format.
Not DVCAM!
Use a tape recorded in 525/60 format. (For DSR1800)
625/50 Tape (For DSR1800)
Use a tape recorded in 625/50 format. (For DSR1800P)
525/60 Tape (For DSR1800P)
Tape not recordable.
Use a DVCAM/DV ME tape.
REC INHI.!
Tape not usable.
Use a DVCAM/DV/DVCPRO (25M) tape.
ILL. Tape!
TC EXTERNAL is selected.
Set the TC MODE menu item (see page 60) to INT
PRESET.
TC EXT!
TCG REGEN mode is selected.
Set the TC MODE menu item (see page 60) to INT
PRESET.
REGEN mode!
TCG RUN mode is set to REC RUN.
Set the RUN MODE menu item (see page 60) to
FREE RUN.
REC RUN!
Chapter 6 Maintenance and Troubleshooting
98
Troubleshooting
Appendixes
Precautions
On safety
• Should any liquid or solid object fall into the cabinet,
unplug the unit and have it checked by qualified
personnel before operating it further.
• Unplug the unit from the wall outlet if it is not to be used
for an extended period of time.
• To disconnect the cord, pull it out by the plug. Never pull
the cord itself.
On operation and storage locations
Avoid operation or storage in any of the following places.
• Location subject to extremes of temperature (operating
temperature range 5ºC to 40ºC (41ºF to 104ºF))
• Location subject to direct sunlight for long periods, or
close to heating appliances (Note that the interior of a car
left in summer with the windows closed can exceed 50ºC
(122ºF).)
• Damp or dusty places
• Location subject to severe vibrations
• Location near equipment generating strong
electromagnetic emissions
• Location near transmitting stations generating strong
radio waves
Avoid violent impacts
Dropping the unit, or otherwise imparting a violent shock
to it, is likely to cause it to malfunction.
Do not obstruct ventilation openings
To prevent the unit from overheating, do not obstruct
ventilation openings, by for example wrapping the unit in
a cloth while it is in operation.
On cleaning
If the casing or panel is dirty, wipe it gently with a soft dry
cloth. In the event of extreme dirt, use a cloth steeped in a
neutral detergent to remove the dirt, then wipe with a dry
cloth. Applying alcohol, thinners, insecticides, or other
volatile solvents may result in deforming the casing or
damaging the finish.
On repacking and shipping
Save the original shipping carton and packing material;
they will come in handy if you ever have to ship your unit.
For maximum protection, repack your unit as it was
originally packed at the factory, and take care not to impart
violent shocks in transit.
Operate the unit in a horizontal position
This unit is designed to be operated in a horizontal
position. Do not operate it on its side, or tilted through an
excessive angle (exceeding 20º).
Precautions
99
Specifications
Dimensions (w/h/d, excluding projections)
427 × 174 × 400 mm
(167/8 × 67/8 × 153/4 inches)
General
Appendixes
100
Specifications
320(12 5/8)
174(6 7/8)
34(1 3/8)
400(15 3/4)
Signal system
372(14 3/4)
18(23/32)
DSR-1800: NTSC
DSR-1800P: PAL
Power requirements
100 V to 240 V AC, 50/60 Hz
Power consumption (with all options installed)
DSR-1800:
100 W/120 V
DSR-1800P for Europe:
100 W/220 V
DSR-1800P for USA and Canada:
100 W/120 V
Peak inrush current
(1)Power ON, current probe method:
40 A (100 V), 40 A (240 V)
(2)Hot switching inrush current,
measured in accordance with
European standard EN55103-1:
40 A (230 V)
Operating temperature
5ºC to 40ºC (41ºF to 104ºF)
Storage temperature
−20ºC to +60ºC (−4ºF to +140ºF)
Operating relative humidity
Less than 80%
Storage relative humidity
Less than 90%
Mass
13 kg (28 lb 10 oz)
427(16 7/8)
Unit: mm (inches)
Tape transport control system
Tape speed
DSR-1800: 28.193 mm/s
DSR-1800P: 28.221 mm/s
Recording/playback time
Using PDV-184ME standard-size
cassette:
Maximum 184 minutes
Using PDVM-40ME mini-size cassette:
Maximum 40 minutes
Fast forward/rewind time
Using PDV-184ME standard-size
cassette:
Less than 3 minutes
Using PDVM-40ME mini-size cassette:
Less than 1 minute
Search speed
When controlling via RS-422A interface:
Maximum 60 times normal speed in
both directions
When controlling from DSRM-10
Remote Control Unit:
Jog mode: 0 (still) to 2 times normal
speed in both directions
Shuttle mode: 8 speeds from 0 (still) to
16 times normal speed in both
directions
Video performance
Input connectors
Band width
Digital signal inputs
SDTI (QSDI) IN (with optional DSBK-1802 SDTI (QSDI)
Input/Output Board installed)
BNC type, SDTI (QSDI) format (270
Mbps)
SDI IN (with optional DSBK-1801 SDI/AES/EBU Input/
Output Board installed)
BNC type (×2, active-through), Serial
Digital Interface format (270 Mbps),
SMPTE 259M/CCIR656-III
i.DV IN/OUT (with optional DSBK-1803 i.LINK/DV
Input/Output Board installed)
6-pin IEEE 1394 connector
S/N
Y/C delay
K-factor
Composite (DSR-1800):
30 Hz to 4.2 MHz ±1.0 dB (Y)
Composite (DSR-1800P):
25 Hz to 4.8 MHz ±1.0 dB (Y)
S-video (DSR-1800):
30 Hz to 5.0 MHz ±1.0 dB (Y),
5.75 MHz +0/−3.0 dB (Y) (TM)
S-video (DSR-1800P):
25 Hz to 5.0 MHz ±1.0 dB (Y),
5.5 MHz +1.0/−2.0 dB (Y),
5.75 MHz +0/−3.0 dB (Y) (TM)
Component (DSR-1800):
30 Hz to 5.0 MHz ±1.0 dB (Y),
5.75 MHz +0/−3.0 dB (Y) (TM),
30 Hz to 1.3 MHz ±1.0 dB (C),
1.5 MHz +0/−5.0 dB (C)
Component (DSR-1800P):
25 Hz to 5.0 MHz ±1.0 dB (Y),
5.5 MHz +1.0/−2.0 dB (Y),
5.75 MHz +1.0/−3.0 dB (Y) (TM),
25 Hz to 1.5 MHz ±1.0 dB (C),
2.0 MHz +1.0/−2.0 dB (C)
Composite I/O (Y):
53 dB or more
S-video I/O (Y): 55 dB or more
Component I/O (Y): 55 dB or more
30 ns or less
2.0% or less (K2T, KPB)
Processor adjustment range
Analog video inputs
REF. VIDEO IN
BNC type (×2, loop-through)
Black burst
0.286 V (DSR-1800) or 0.3 V (DSR1800P), 75 Ω, negative sync
Composite sync
VIDEO IN
BNC type (×2, loop-through), composite,
1.0 Vp-p, 75 Ω, sync negative
COMPONENT VIDEO IN
BNC type (×3)
Y: 1.0 Vp-p, 75 Ω, negative sync
R−Y/B−Y: 0.7 Vp-p (75% color bars
for DSR-1800 or 100% color bars for
DSR-1800P), 75 Ω
S VIDEO IN
DIN 4-pin
Y: 1.0 Vp-p, 75 Ω
C: 0.286 Vp-p (DSR-1800) or
0.3 Vp-p (DSR-1800P), 75 Ω (burst
level)
Video level
±3 dB/−∞ to 3 dB selectable
Chrome level ±3 dB/−∞ to 3 dB selectable
Setup/Black level
±30 IRE (±210 mV)
Chroma phase ±30°
Y/C delay
±100 ns
System phase Sync: ±1 µs*
SC: ±180°
Analog audio inputs
AUDIO IN
XLR 3-pin, female (×4), +4/0/−3*/−6
dBm, 600 Ω ON/OFF/−60 dBu, high
impedance, balanced
* +2 µs to -3 µs when using a TBC remote control unit
* Selectable on DSR-1800P only
Audio performance
Time code input
TIME CODE IN
BNC type, SMPTE time code (DSR1800) or EBU time code (DSR1800P), 0.5 Vp-p to 18 Vp-p, 3.3 kΩ,
unbalanced
Specifications
Appendixes
Frequency response
Two-channel (48 kHz) mode:
20 Hz to 20 kHz +0.5 dB/−1.0 dB
Four-channel (32 kHz) mode:
20 Hz to 14.5 kHz +0.5 dB/−1.0 dB
Dynamic range More than 90 dB
Distortion (THD + N)
Less than 0.05% (48 kHz)
Digital audio inputs
DIGITAL AUDIO (AES/EBU) IN (with optional DSBK1801 SDI/AES/EBU Input/Output Board installed)
BNC type (×2), complying with AES3id-1995
101
Output connectors
Digital signal outputs
SDTI (QSDI) OUT (with optional DSBK-1802 SDTI
(QSDI) Input/Output Board installed)
BNC type, SDTI (QSDI) format (270
Mbps)
SDI OUT (with optional DSBK-1801 SDI/AES/EBU
Input/Output Board installed)
BNC type (×2, active-through), Serial
Digital Interface format (270 Mbps),
SMPTE 259M/CCIR656-III
i.DV IN/OUT (with optional DSBK-1803 i.LINK/DV
Input/Output Board installed)
6-pin IEEE 1394 connector
Analog video outputs
REF. VIDEO OUT
BNC type ×1
Black burst
0.286 V (DSR-1800) or 0.3 V (DSR1800P), 75 Ω, negative sync
Composite sync
VIDEO OUT 1, 2 (SUPER)
BNC type (×2), composite, 1.0 Vp-p,
75 Ω, sync negative
COMPONENT VIDEO OUT
BNC type (×3), Y/R−Y/B−Y
Y: 1.0 Vp-p, 75 Ω, sync negative
R−Y: 0.7 Vp-p, 75 Ω (75% color bars for
DSR-1800 or 100% color bars for
DSR-1800P)
B−Y: 0.7 Vp-p 75 Ω (75% color bars for
DSR-1800 or 100% color bars for
DSR-1800P)
S VIDEO OUT DIN 4-pin
Y: 1.0 Vp-p, 75 Ω, sync negative
C: 0.286 Vp-p (DSR-1800) or 0.3 Vp-p
(DSR-1800P), 75 Ω (burst level)
Analog audio outputs
AUDIO OUT XLR 3-pin, male (× 4), +4/0/−3*/−6
dBm, 600 Ω loading, low impedance,
balanced
AUDIO MONITOR OUT
Phono jack, −11 dBu ±1 dBu, 47 kΩ,
unbalanced
* Selectable on DSR-1800P only
Appendixes
102
Digital audio outputs
DIGITAL AUDIO (AES/EBU) OUT (with optional
DSBK-1801 SDI/AES/EBU Input/Output Board installed)
BNC type (×2), complying with AES3id-1995
Specifications
Output for headphones
HEADPHONES
Stereo phone jack, −∞ to −13 dBu, 8 Ω,
unbalanced
Time code output
TIME CODE OUT
BNC type, SMPTE time code (DSR1800), EBU time code (DSR-1800P),
2.2 Vp-p ±3 dB, 600 Ω, unbalanced
Remote control connectors
REMOTE
D-sub 9-pin, for connection of editing
control unit*, RS-422A standard
CONTROL S Stereo minijack, for connection of
SIRCS-compatible remote control unit
(DSRM-10)
VIDEO CONTROL
D-sub 15-pin, for connection of TBC
remote control unit**
i.DV IN/OUT (with optional DSBK-1803 i.LINK/DV
Input/Output Board installed)
6-pin IEEE 1394 connector
* ES-7, PVE-500, RM-450/450CE, BVE-600/800/910/2000/9100/9100P,
etc.
**UVR-60/60P, etc.
Supplied accessories
AC power cord (1)
Operating Instructions (1)
Optional accessories
DSBK-1801 SDI/AES/EBU Input/Output Board
DSBK-1802 SDTI (QSDI) Input/Output Board
DSBK-1803 i.LINK/DV Input/Output Board
RCC-5G/10G/30G 9-pin remote control cable (length: 5 m
(16 ft)/10 m (33 ft)/30 m (98 ft))
RMM-130 Rack Mount Kit
Digital video cassette
Standard size: PDVM-64ME/94ME/
124ME/184ME
Mini size: PDVM-12ME/22ME/32ME/
40ME
Cleaning cassette
DV12CL (standard size), DVM12CL
(mini size)
Related equipment
ES-3/7 EditStation
Linear editing control unit: PVE-500, RM-450/450CE,
BVE-600/800/910/2000/9100/9100P
DME switcher: DFS-300/300P, DFS-500/500P,
DFS-700/700P
DXC-D30/D30P Color Video Camera
DSR-1/1P/300A Digital Videocassette Recorder
DSR-85/85P/2000/2000P Digital Videocassette Recorder
DSR-1600/1600P Digital Videocassette Player
DSR-300/300P/500WS/500WSP/130/130P/150/150P
Digital Camcorder
DSRM-10 Remote Control Unit
TBC remote control unit: UVR-60/60P, BVR-50/50P
Design and specifications are subject to change without
notice.
Appendixes
Specifications
103
ClipLink Guide
What Is ClipLink?
The ClipLink function greatly improves the efficiency of
the video production process as a whole by recording
various editing-related data on tape when shooting. As
such, ClipLink is a revolutionary function that transcends
the conventional separation of shooting and editing.
How ClipLink Changes Video Production
Techniques
The following describes various ways in which ClipLink*
video production differs from conventional video
production.
* The ClipLink system is a video production system which uses the cassette
memory function.
Recording of ClipLink log data lightens the
shooting workload
When you start shooting a scene, ClipLink log data such as
the scene number and time code data are automatically
recorded into the cassette memory. This eliminates the
need for a conventional “shot list” compiled by someone
using a stopwatch, clipboard and pencil. You can also
designate unwanted scenes as “NG” (no good) and
automatically skip all “NG” scenes when editing.
Recorded index pictures drastically cut editing
time
The ClipLink function also features index pictures as a
time-saving tool for rough editing. Each index picture is a
compressed image taken from the start of each scene,
which is recorded onto the tape as a still picture. When
editing, begin by transferring only the index pictures and
the ClipLink log data to the EditStation’s hard disk. You
can also transfer OK scenes only (“NG” scenes are
skipped).
Next, begin rough editing by viewing the index pictures on
the EditStation’s GUI display and rearranging them as you
wish. This eliminates the difficult work of matching up a
handwritten shot list with recorded scenes. After you have
completed this rough editing, you can then transfer only
the recordings needed for your video program.
Appendixes
104
ClipLink Guide
High-speed transfer of recordings
It is also possible to transfer the editing material itself
between the DSR-85/85P and ES-7 at four times normal
speed. In other words, the transfer can be carried out in one
fourth of the real time duration. It is of course possible to
carry out a transfer at four times normal speed when
backing up video and audio data recorded on the disk drive
to the DSR-85/85P, or in the opposite direction when
loading data backed up on the DSR-85/85P to the disk
drive. Thus the time required is much shorter than with
conventional equipment (for which, for example,
transferring a 40-minute segment of video takes 40
minutes).
Example System Configuration and Operation Flow
The following illustration shows an example system
configuration for using the ClipLink function and a typical
ClipLink operation flow.
Shooting
DVCAM standard cassette or DVCAM mini cassette
DVCAM camcorder
(DSR-130/130P/
300/300P/500WS/
500WSP)
Index pictures: recorded on
tape
ClipLink log data: recorded in
cassette memory
ClipLink log data recorded onto DVCAM
cassettes links shooting and editing
operations.
ClipLink log data transfer
ES-7 EditStation nonlinear editing system
DSR-85/1800/1600 a) or
DSR-85P/1800P/1600P a)
Digital Videocassette
Recorder/Player
Index pictures
Video output (SDTI) b)
ClipLink log data
RS-422A interface
Editing
ES-7 EditStation nonlinear editing system
DSR-85 c)/1800/1600 a) or
DSR-85P c)/1800P/1600P a)
Digital Videocassette
Recorder/Player
Actual AV data
SDTI input/output b)
Appendixes
a) The DSR-1600/1600P is a videocassette player.
b) To transfer SDTI signals between the DSR-1800/1800P and ES-7, installation of the DSBK-1802
SDTI (QSDI) Input/Output Board on the DSR-1800/1800P is required; to send an SDTI signal from
the DSR-1600/1600P to the ES-7, installation of the DSBK-1602 SDTI (QSDI) Output Board on the
DSR-1600/1600P is required.
c) Between the DSR-85/85P and ES-7, quadruple transfer is possible through the SDTI interface.
ClipLink Guide
105
ClipLink log data
Data Generated When Shooting
The following describes the kinds of data that is generated
when using the ClipLink function.
ClipLink log data can be recorded automatically or
manually into the cassette memory for use as a convenient
alternative to the conventional “shot list.”
ClipLink log data includes the following items.
Index pictures
When shooting, a single-frame image from the Mark IN
point at the start of each scene is recorded as a still picture
into the camcorder’s internal memory. These images are
called “index pictures.” When you finish shooting, the
index pictures from all scenes are recorded onto the tape
after the last scene.
ClipLink log data Description
Reel number
Data (maximum length: 8 digits)
(cassette number) consisting of alphanumeric characters
and/or symbols (This is left blank at
shipping.)
Scene number
A three-digit number from 001 to 198
(starts at 001 and is automatically
incremented with each scene.)
Take number
This cannot be changed (set to “1” at
shipping).
OK/NG
Indicates the OK/NG status of a
particular scene. (In the OK case,
nothing is recorded.)
Mark IN/OUT
point time codes
These are the time codes that indicate
the Mark IN and Mark OUT points for
each scene (HH:MM:SS). These time
codes are recorded when the camera
has been set to MARK mode.
The time code value is rounded up at
each Mark IN point and rounded down
at each Mark OUT point, to a whole
number of seconds.
For details, see “Time codes recorded
for Mark IN/OUT points” on page 108.
Cue point time
code
This is the time code that indicates the
cue points (valid up to the frame digit).
This time code is recorded when the
camera has been set to CUE mode.
When in this mode, the time codes at
the start and end of a recording (the
Rec IN and Rec OUT time codes) are
automatically recorded as Mark IN and
OUT points, respectively.
Tape
Scene 1
Scene 2
Scene 3
DVCAM camcorder’s
internal memory
Scene n
After shooting, the index
pictures in the internal
memory are recorded onto
the video tape.
Up to 32 index pictures can be recorded onto the tape space
normally occupied by one frame, as shown below.
Index picture
(72)
60
(144)
120
(216)
180
(288)
240
(360)
300
(432)
360
(504)
90
1
180
270
2
360
450
3
540
630
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
420
480 lines (NTSC) or 576
lines (PAL)
0
(PAL) NTSC
720 dots
Appendixes
106
Seven frame spaces are reserved at the end of the last scene
as a recording area for index pictures. (A cassette with 16
Kbits of cassette memory can record up to 198 index
pictures, and a cassette with 4 Kbits of cassette memory
can record up to 45 index pictures.)
ClipLink Guide
How to record ClipLink log data
The following describes how to record the various
ClipLink log data items.
OK/NG status
To designate a scene as “NG,” press the NG button on the
camera while shooting the scene or at any time before you
begin shooting the next scene.
All scenes that do not receive an “NG” designation are
recorded as “OK” scenes.
(When you exit the VCR recording mode, changing the
OK/NG status is no longer possible.)
Mark IN/OUT point time codes
This data is especially useful when shooting a video
program for which a scenario has been created.
Set the camera to MARK mode before you start shooting.
While shooting, each time you press the camera’s TAKE
button, Mark IN and Mark OUT point time codes are
recorded alternately.
Index picture 1
Start
recording
Index picture 1
Index picture 2
End
recording
Start
recording
Mark IN
(manual
recording)
Mark IN
(manual
recording)
Cue point time codes
This type of data is especially useful when shooting scenes
that may contain unexpected events, such as when
shooting for sports coverage or documentaries.
Set the camera to CUE mode before you start shooting.
While shooting, each time you press the camera’s TAKE
button, the current time code is recorded as a cue point
time code.
Rec IN
(automatic
recording)
Cue point
time code
(manual
recording)
Cue point
time code
(manual
recording)
End
recording
Rec OUT
(automatic
recording)
Cue point
time code
(manual
recording)
Mark OUT
(manual
recording)
Mark OUT
(manual
recording)
Appendixes
ClipLink Guide
107
Time codes recorded for Mark IN/OUT points
There is a gap between actual time codes and Mark IN/
OUT time codes recorded in the cassette memory, as
shown in the figure below. The time code value is rounded
up at each Mark IN point and rounded down at each Mark
OUT point, to a whole number of seconds.
Mark IN
(or Rec IN)
Actual time code
12:23:15:10
Cue
12:34:20:20
12:23:16
(The index
picture is the
image around
12:23:15:10.)
Recording capacity for Mark IN/OUT point
time codes and cue point time codes
When in MARK mode, up to 198 pairs of Mark IN and
Mark OUT points can be recorded (if using a cassette with
16 Kbits of cassette memory).
When in CUE mode, up to 396 time code points (including
all cue point time codes and all Mark (Rec) IN and Mark
(Rec) OUT point time codes) can be recorded (if using a
cassette with 16 Kbits of cassette memory).
Appendixes
108
ClipLink Guide
12:39:24:23
Rounded down
Rounded up
Time code
recorded in the
cassette memory
Mark OUT
(or Rec OUT)
12:34:20:20
12:39:24
Glossary
A/B roll editing
An editing method that uses two or
more playback VCRs to create
special effects such as dissolve and
wipe, and uses one record VCR to
record the results of the editing.
Using an editing control unit allows
efficient control of the VCRs and
very precise editing.
Drop frame mode
Time code runs at 30 frames/sec. The
NTSC system, however, runs at
about 29.97 frames/sec. Drop frame
mode adjusts this difference. The
time code and video are synchronized
by dropping the first two frames of
the time code every minute, except at
the ten-minute marks.
AES/EBU format
A unified format for digital audio
signals. It allows a single connector
to carry the signals for two channels.
EE mode
EE is an abbreviation of “Electric to
Electric”. Video and audio signals are
supplied to the VCR’s internal
circuits, but not to the recording
heads.
B−
−Y signal
A chrominance signal determined by
subtracting the Y (luminance) signal
from the B (blue) signal. One of the
component signals.
Capstan
A drive mechanism that moves the
tape at a specified speed. Its rotation
normally synchronizes with a
reference sync signal.
Chrominance signal
Color signal containing color
information such as hue and
saturation. Also called C signal.
Head drum
A metal cylinder to which a video
head is attached. This drum is rotated
at high speeds in synchronization
with the sync signal during recording
and playback.
Linear editing
Editing while playing back video and
audio signals recorded on video tape.
See also “Non-linear editing.”
Composite signal
A composite video signal containing
video, burst and sync signals.
Loading
When being loaded, the tape is pulled
out of the cassette case and threaded
along the specified tape path and
wrapped round the drum to be ready
for recording or playback. Generally,
this is done automatically when you
place the cassette at the cassette
entrance of the VCR. Also called
threading.
Condensation
Condensation of moisture on the tape
transport mechanisms of VCRs
including the head drum. If moisture
condenses on the head drum, the tape
adheres to the drum and causes
malfunction.
Loop-through connection
A connection which allows a signal
input to an input connector to pass
through the unit and exit from an
output connector as input to external
equipment. Also called bridging
connection.
Component signals (YRB)
A video signal consisting of a
luminance signal (Y) and two
chrominance signals (R−Y, B−Y).
Non-linear editing
Editing while playing back video and
audio signals recorded on hard disks.
Video scenes stored on disk can be
cued up quickly, for increased editing
efficiency. See also “Linear
editing.”
PCM audio
This is an audio signal represented by
pulse code modulation. The analog
audio signal is first broken down into
a sequence of pulses, and these are
then represented digitally.
Preroll
Running of a video tape to a prior to
an edit-start point to enable the tape
to reach a steady speed and to be
synchronized with other video tapes.
R−
−Y signal
A chrominance signal determined by
subtracting the Y (luminance) signal
from the R (red) signal. One of the
component signals.
Reference video signal
A video signal consisting of a sync
signal or sync and burst signals, used
as a reference.
Setup (for DSR-1800)
The difference between the reference
black level and the blanking level of
a composite signal.
SMPTE
Abbreviation of Society of Motion
Picture and Television Engineers, a
professional association established
in the USA.
Glossary
Appendixes
Luminance signal
The signal that determines the
brightness of the picture. Also called
Y signal. One of the component
signals.
Non-drop frame mode
The number of frames of the time
code and video run is not adjusted.
When you use the time code in nondrop frame mode, the real playback
time will be about 86 seconds shorter
per day than the time code. If you edit
frame by frame or if you determine
the length of a shot by counting the
time code, use drop frame mode.
109
S/N
Abbreviation of Signal-to-Noise
(ratio). The higher the S/N value, the
less noise and higher the picture
quality.
Search mode
A VCR operating mode used when
searching for specific scenes, by
viewing the video output or time code
values while playing back the tape at
various speeds in forward or reverse
direction.
Servo lock
Synchronizing the drum rotation
phase and tape transport phase with a
reference signal during playback and
recording so that the video heads scan
the tape in the same pattern during
playback and recording.
Standby Off mode
One of two conditions in the stop
mode. The drum does not rotate and
tape is slackened. There is no damage
to the video heads and the tape, but
the VCR is not ready for immediate
recording or playback.
Standby On mode
One of two conditions in the stop
mode. The drum is rotating and the
tape is wrapped round the drum. The
VCR is ready for recording or
playback, so a still picture can be
obtained.
Subcarrier
A sine wave imposed on the
luminance portion of a video signal
and modulated to carry color
information. Its amplitude represents
color saturation and its phase
represents hue.
Superimpose
To put a set of characters onto a
picture so that both can be seen at the
same time.
S-video
A signal format in which Y
(luminance) and C (chrominance)
signals are separated to reduce
interference between them so that
noiseless images are reproduced.
Sync signal
A reference signal consisting of
vertical and horizontal sync signals
used for synchronizing the scanning
patterns of the video camera and the
monitor.
TBC
Abbreviation of Time Base
Corrector. Electronic circuits to
electrically stabilize the playback
signals by removing color variation
and roll in the playback picture
caused by irregularity in drum
rotation and tape movement. Time
base correction reduces deterioration
of picture quality when transmitting
or copying playback signals.
Threading
See “Loading.”
Time code
Signals recorded on the tape to
supply information on tape position
such as the hour, minute, second and
frame, to assist in setting edit points
or searching for particular scenes.
Unloading
When the EJECT button is pressed,
the VCR automatically winds the
tape back into the cassette case. Also
called “Unthreading.”
User bits
Sections of time code information
consisting of a total of 32 bits that can
be used for recording information
such as date, tape ID number,
program ID number, etc.
Appendixes
110
Glossary
Index
Numerics
9PIN button 15
A/B roll editing system 80
AC IN connector 16
Alarm messages 96
Analog audio signal input/output
section 19
Analog interfaces 6
Analog recording 87
Analog video signal input/output
section 17
Arrow buttons 11
Aspect ratio 7
AUDIO CH1 1/2 display 9
AUDIO CH2 3/4 display 9
AUDIO IN CH-1 to CH-4 connectors
20
AUDIO IN LEVEL/600-ohm switches
19
AUDIO INPUT LEVEL control knobs
9
Audio level meters 8
AUDIO MONITOR OUT connector
20
Audio monitor system connections 82
AUDIO OUT CH-1 to CH-4
connectors 20
Audio performance 101
AUTO FUNCTION execution menu
69
Auto mode execution menu 69
B
Basic items 53, 70
C
Cassette compartment 8
Cassette memory indicator 14
CH1,1/2 button 11
CH2,3/4 button 11
CHANNEL CONDITION indicators
14
ClipLink 6
example system configuration
105
guide 104
index pictures 104, 106
log data 104, 106
ClipLink indicator 13
D
DIGITAL AUDIO (AES/EBU) IN
connectors 19
DIGITAL AUDIO (AES/EBU) OUT
connectors 19
Digital dubbing 50
Digital hours meter 7, 91
display modes 91
indications in the time counter
display 92
indications on the monitor 92
Digital jog sound function 7
Digital signal input/output section 18
Digital slow-motion playback 7
Display section 13
Drop frame indication 42
DSBK-1801 SDI/AES/EBU Input/
Output Board 7
DSBK-1802 SDTI (QSDI) Input/
Output Board 7
DSBK-1803 i.LINK/DV Input/Output
Board 7
DVCAM 5
E
EBU 6
Editing control unit 85
EE OUT PHASE settings 67
THROUGH mode 67
VIDEO INPUT PHASE mode 67
VIDEO OUTPUT PHASE mode
68
EJECT button 12
Enhanced items 53, 72
Error messages 96
External device connectors 20
F
F FWD button 12
Factory default settings 73
FREE RUN 44
Front panel 8
Index
A
COMPONENT VIDEO IN Y/R-Y/BY connectors 17
COMPONENT VIDEO OUT Y/R-Y/
B-Y connectors 18
Condensation 91
Connections 77
analog recording 87
audio monitor system 82
control signal 83
for A/B roll editing system 80
for cut editing system 79
for digital non-linear editing
system 77
for dubbing via i.LINK interface
50
for dubbing via SDTI (QSDI) 50,
86
video monitor 85
video/audio signals 84
CONTROL S connector 9
Control signal connections 83
COUNTER 43
COUNTER SEL button 11
Cue point 107
Cut editing system 79
H
Head cleaning 93
HEADPHONES connector 9
I
i.DV IN/OUT connector 19
i.LINK (DV) 6
i.LINK button 15
Index pictures 104, 106
Initial time code value 43
INPUT display 9
INPUT SELECT section 11
Input selection/audio mode display
section 9
Interfaces 6
Internal time code generator 43
FREE RUN 44
REC RUN 44
J
JOG indicator 14
Jog mode 15, 49
Jog sound function 7
L
Log data 104, 106
cue point 107
Mark IN/OUT points 107, 108
OK/NG status 107
recording capacity 108
M
Maintenance 91
condensation 91
head cleaning 93
regular checks 91
Mark IN/OUT points 107, 108
Menu 53
changing settings 70
contents 56
factory default settings 73
Index
111
item indications 56
MENU button 11
Menu control panel 10
MONITOR SELECT switches 10
N
Non-linear editing 5, 77
NOT EDITABLE indicator 14
Index
O
OK/NG status 107
Operation mode indications 41, 42
Optional accessories 102
P
PB FS display 9
PCM digital audio 5
Phases adjustment 88
PHONE LEVEL control knob 8
PLAY button 12
Playback 49
Playback modes 15
jog mode 49
shuttle mode 49
POWER switch 8
Precautions 99
Processor adjustment range 101
R
Rack mount 7
Rear panel 16
REC button 12
REC INHIBIT indicator 14
REC MODE display 9
REC RUN 44
Recording/playback format indicators
13
REF. VIDEO IN/OUT connectors 17
Reference video signals 79
Regular checks 91
Related equipment 103
REMOTE button 15
REMOTE connector 20
Remote control 6
Remote control setting section 15
REPEAT indicator 14
Rerecording time code 45
RESET (NO) button 11
REW button 12
RMM-130 Rack Mount Kit 7
RS-422A interface 6
S
S VIDEO IN connector 17
112
Index
S VIDEO OUT connector 18
SC PHASE control 12
SDI IN connector 19
SDI OUT connectors 19
SDI/AES/EBU 6
SDTI (QSDI) 6
dubbing 86
SDTI (QSDI) IN/OUT connectors 19
SDTI/i.LINK button 11
Search 6, 14, 48, 49
via external equipment 48
SEARCH button 14
Search control section 14
Search dial 14
SERVO indicator 14
SET (YES) button 11
Setup menu 56
AUDIO CONTROL 63
DIGITAL PROCESS 65
DISPLAY CONTROL 59
MENU GRADE 66
OPERATIONAL FUNCTION
56
SETUP BANK OPERATION 66
TAPE PROTECTION 62
TIME CODE 60
VIDEO CONTROL 62
SHUTTLE indicator 14
Shuttle mode 15, 49
SIRCS 6
Slow-motion playback 7
SMPTE 6
Specifications 100
STOP button 12
Subcarrier phase 88
Superimposition 7, 18
Supplementary status information 74
Supplied accessories 102
Sync phase 88
SYNC PHASE control 12
Synchronizing time codes 45
T
Tape end alarm indicator 14
Tape transport control section 12
TC 43
TC insert function 45
TC PRESET button 12
Time code
generator/reader 6
rerecording 45
TIME CODE IN/OUT connectors 18
Time counter display 14, 43
Time data
displaying 41
setting 41
Time data type 42
COUNTER 43
indicators 14
TC 43
U-BIT 43
Track pitch 5
Troubleshooting 94
alarm messages 96
error messages 96
U
U-BIT 43
V
VIDEO CONTROL connector 20
VIDEO display 9
VIDEO IN button 11
VIDEO IN connectors 17
Video monitor connection 85
VIDEO OUT 1 and 2 (SUPER)
connectors 18
Video performance 101
Video process control 7
Video/audio signal connections 84
VITC field indication 42
VITC indicator 14
W
Wide-screen 7
Sony Corporation
Printed in Japan

advertisement

Key Features

  • DVCAM digital recording format
  • Superb picture quality
  • Professional digital video editing system
  • ClipLinkTM function for efficient editing
  • Full-fledged analog interface
  • Multi-generation dubbing without quality loss
  • Wide track pitch for reliability and precision
  • High-quality PCM digital audio
  • Playback compatibility with DV and DVCPRO formats

Frequently Answers and Questions

What is the recording format used by the DSR-1800/1800P?
The DSR-1800/1800P uses the DVCAM digital recording format.
What kind of editing systems is the DSR-1800/1800P compatible with?
The DSR-1800/1800P is compatible with professional digital video editing systems, including non-linear editing systems when connected to a Sony EditStationTM.
Can I use analog equipment with the DSR-1800/1800P?
Yes, the DSR-1800/1800P has a full-fledged analog interface to support hybrid systems that combine conventional analog equipment with digital equipment.

Related manuals

Download PDF

advertisement