Sony FWD-50PX2 Flat Panel Television User Manual

Sony FWD-50PX2 Flat Panel Television User Manual
FLAT WIDE DISPLAY
FWD-50PX2
PROTOCOL MANUAL
1st Edition
Table of Contents
1. Communication Parameter ................................................................ 1
2. Pin Configuration ..................................................................................... 1
3. Communication Data Format ........................................................... 1
4. General Function ..................................................................................... 3
5. Picture/Sound .......................................................................................... 12
6. Size/Shift .................................................................................................... 14
7. Status Enquiry ........................................................................................ 16
8. User Reset ................................................................................................. 19
FWD-50PX2
1. Communication Parameter
3. Communication Data Format
(a) Control (Host → Request of Write to Display)
Communication system
RS-232C
Synchronous system
Asynchronous communication
No.
Item
Value
Baud rate
9600 bps
1
Header
0x8C:Control
Character length
8 bit
2
Category
0xXX
Parity
None
3
Function
0xXX
Start bit
1 bit
4
Data1 (Length)
0xXX
Stop bit
1 bit
5
Data2 (Data1)
0xXX
Flow control
None
:
:
0xXX
:
:
0xXX
X
DataX
0xXX
X+1
Check Sum
0xXX
2. Pin Configuration
Display side (D-sub 9-pin)
Host side (D-sub 9-pin)
FWD-50PX2
Personal computer
* Check Sum: The total from No. 1 to No. X, when value exceeds 255,1byte
of data is confirmed the bottom.
* Set the command interval to 500 ms or more when transmitting the
Control command continuously.
* Set the command interval to 500 ms or more when transmitting the same
command (Enquiry) after the Control command.
(b) Enquiry (Host → Request of Read to Display)
5
4
9
3
8
2
7
1
6
_ External view _
Pin No.
1
2
3
4
5
6
7
8
9
FWD-50PX2
Signal
NC
TD
RD
NC
GND
NC
NC
NC
NC
5
4
9
3
8
2
7
1
6
_ External view _
Pin No.
1
2
3
4
5
6
7
8
9
Signal
NC
RD
TD
NC
GND
NC
NC
NC
NC
No.
Item
Value
1
Header
0x83:Enquiry
2
Category
0xXX
3
Function
0xXX
4
Data1
0xFF
5
Data2
0xFF
6
Check Sum
0xXX
* Check Sum: The total from No.1 to No.5, when value exceeds 255, 1byte
of data is confirmed the bottom.
1
(c) Answer (Display → Response to Host)
1 Control answer
4 Error answer
No. Item
Value
No. Item
Value
1
Header
0xE0: Answer
1
Header
0x70: Answer
2
Answer*
0x00: No Function Error
2
Answer*
0x00: Completed
0x01: Check Sum Error
0x01: Limit Over
0x02: Data Length Error
0x02: Limit Under
0x03: Command Canceled
3
Check Sum 0xXX
* 0x00: Completed
0x01: Limit Over
Normal response.
The packets was received normally, but the
data value was over the upper limit.
Forcedly the monitor adjusted the data to
maximum value.
0x02: Limit Under
The packets was received normally, but the
data value was under the lower limit.
Forcedly the monitor adjusted the data to
minimum value.
0x03: Command Canceled The packets was received normally, but the
command was cancelled because the function
was not in adjustable mode, such as “_” a
function displayed as in user menu.
* Check Sum:
The total from No.1 to No.2, when value
exceeds 255, 1byte of data is confirmed the
bottom.
3
Check Sum
0xXX
* 0x00: No Function Error Packet header, category of function codes do not
exist in this protocol.
0x01: Check Sum Error The “Check Sum” value of the packet which
received is wrong.
0x02: Data Length Error The “Data Num” value of the packet which
received is wrong.
2 Enquiry answer (Complete)
No. Item
Value
1
Header
0x70: Answer
2
Answer
0x00: Completed
3
Return Data Size 0xXX
4
Return Data1
0xXX
:
:
0xXX
:
:
0xXX
X
Return DataX
0xXX
X+1 Check Sum
0xXX
* 0x00: Completed Normal response.
* Return Data returns the read value.
* Check Sum: The total from No.1 to No.X, when value exceeds 255,1byte
of data is confirmed the bottom.
3 Enquiry answer (Command cancel)
No. Item
Value
1
Header
0x70: Answer
2
Answer
0x03: Command Canceled
3
Check Sum
0xXX
* 0x03: Command Canceled The packets was received normally, but the
command was cancelled because the function
was not in adjustable mode, such as “_” a
function displayed as in user menu.
* Check Sum:
The total from No.1 to No.2, when value
exceeds 255, 1byte of data is confirmed the
bottom.
2
FWD-50PX2
4. General Function
(a) Mode Control
Syntax
Header
Category
Function
Data1
Data2
Check Sum
Control
0x8C
0x00
Code Table(1-a)[a]
0x02
Code Table(1-a)[b]
0xXX
Enquiry
0x83
0xFF
0xFF
0xXX
Answer
Header
Answer
Check Sum
Control
0x70
0x00
0x70
Completed
0x70
0x01
0x71
Limit Over
0x70
0x02
0x72
Limit Under
0x70
0x03
0x73
Command Canceled
Answer
Header
Answer
Return to Data Size
Return Data1
Check Sum
Enquiry
0x70
0x00
0x02
Code Table(1-a)[b]
0xXX
Completed
Code Table(1-a)
[a]Function
0x00
0x01
0x02
0x03
0x04
0x05
Power*1
Input Select*2
Force Status Display
Audio Mute
Auto Status Display
Closed Caption
[b]Range/Switch Code
0x00
OFF
0x01
ON
0x0A
INPUT2 RGB
0x0B
INPUT2 COMPONENT
0x0C
OPTION1 VIDEO
0x0D
OPTION1 S VIDEO
0x0E
OPTION1 RGB
0x0F
OPTION1 COMPONENT
0x10
OPTION2 VIDEO
0x11
OPTION2 S VIDEO
0x12
OPTION2 RGB
0x13
OPTION2 COMPONENT
0x20
INPUT1 DVI
0x00
ON
0x01
OFF
0x00
OFF
0x01
ON
0x00
ON
0x01
OFF
0x00
OFF
0x01
CC1
0x02
CC2
0x03
CC3
0x04
CC4
Command
Control
Enquiry
Standby
Power On
Yes
Yes
Enable
Enable
Yes
Yes
Disable
Enable
Yes
Yes
Disable
Enable
Yes
Yes
Disable
Enable
Yes
Yes
Enable
Enable
Yes
Yes
Disable
Enable
(Continued)
FWD-50PX2
3
Code Table(1-a)
[a]Function
0x06
0x0B
0x0C
0x0D
0x0E
0x0F
Color System
Picture Inversion
Picture Orbit
Orbit Range
Orbit Cycle
Language
[b]Range/Switch Code
0x00
Auto
0x01
NTSC
0x02
NTSC4.43
0x03
PAL
0x04
SECAM
0x05
PAL-M
0x06
PAL-N
0x07
PAL60
0x00
OFF
0x01
Auto
0x02
On
0x00
OFF
0x02
ON
0x00
Small
0x01
Middle
0x02
Large
0x00
10 sec
0x01
30 sec
0x02
1 min
0x03
5 min
0x00
Japanese
0x01
English
0x02
Deutsch
0x03
Français
0x04
Español
0x05
Italiano
Command
Control
Enquiry
Standby
Power On
Yes
Yes
Disable
Enable
Yes
Yes
Disable
Enable
Yes
Yes
Disable
Enable
Yes
Yes
Disable
Enable
Yes
Yes
Disable
Enable
Yes
Yes
Disable
Enable
0x10
Index Number
0x01-0xFF
Yes
Yes
Disable
Enable
0x13
Power Saving
0x00
Standard
Yes
Yes
Disable
Enable
0x01
Reduce
ON
Yes
Yes
Disable
Enable
Yes
Yes
Disable
Enable
Yes
Yes
Disable
Enable
Yes
Yes
Disable
Enable
Yes
Yes
Disable
Enable
Yes
Yes
Disable
Enable
0x14
Speaker Out
0x00
0x01
OFF
0x16
HD Mode
0x00
1080i
0x01
1035i
0x00
DTV
0x01
PC
0x17
0x18
0x1B
0x40
RGB Mode
Sync Mode
Clock Display
All White
0x00
H/Comp
0x01
Video
0x00
OFF
0x01
ON
0x00
OFF
0x01
ON
(Continued)
4
FWD-50PX2
Code Table(1-a)
[a]Function
0x41
0x49
0x65
BackGroud
Auto Dimmer
IP Setting Mode
[b]Range/Switch Code
0x00
Gray
0x01
Dark Gray
0x02
Black
0x00
OFF
0x01
ON
0x00
DHCP
0x01
Manual
Command
Control
Enquiry
Standby
Power On
Yes
Yes
Disable
Enable
Yes
Yes
Disable
Enable
Yes
Yes
Enable
Enable
No
Yes
Enable
Enable
Yes
No
Enable
Enable
Yes
Yes
Enable
Enable
No
Yes
Disable
Enable
0X02 Speed
0x66
0x67
0x68
0x24
IP Setting Execute
IP Setting Result
Speed Setting
Input Detect (Option1)
0x00
No
0x01
Yes
0x00
Done
0x01
Error 1 (UART Commu.)
0x02
Error 2 (Duplication)
0x03
Error 3 (IP Add Setting)
0x04
Error 4 (GW Add setting)
0x05
Error 5 (DNS1 Setting)
0x06
Error 6 (DNS2 Setting)
0x07
Error 7 (Sbnt Msk Setting)
0x00
100Mbps/Full Duplex
0x01
100Mbps/Half Duplex
0x02
10Mbps/Full Duplex
0x03
10Mbps/Half Duplex
0x04
Auto
0x00
U3 (HD15)
0x01
U1 (CVBS/Y, C)
0x02
U2 (BNC)
0x03
Reserved
0x04
FW31/FW32
0x05
FW50
0x06
Reserved
0x07
Reserved
0x08
Reserved
0x09
Reserved
0x0A Reserved
0x0B Reserved
0x0C Reserved
0x0D Reserved
0x0E Reserved
0x0F Not Connected
(Continued)
FWD-50PX2
5
Code Table(1-a)
[a]Function
0x25
Input Detect (Option2)
[b]Range/Switch Code
0x00
U3 (HD15)
0x01
U1 (CVBS/Y, C)
0x02
U2 (BNC)
0x03
Reserved
0x04
FW31/FW32
0x05
FW50
0x06
Reserved
0x07
Reserved
0x08
Reserved
0x09
Reserved
Command
Control
Enquiry
Standby
Power On
No
Yes
Disable
Enable
Yes
Yes
Disable
Enable
Yes
Yes
Disable
Enable
Yes
Yes
Disable
Enable
Yes
Yes
Disable
Enable
Yes
Yes
Disable
Enable
0x0A Reserved
0x0B Reserved
0x0C Reserved
0x0D Reserved
0x0E Reserved
0x0F Not Connect
0x26
0x27
0x28
0x30
0x31
Auto Shut OFF
Auto Screen Adjust
Input Setting
PAP
Active Picture
0x00
OFF
0x01
ON
0x00
OFF
0x01
ON
0x00
Selectable
0x01
Fix
0x00
OFF
0x01
P&P
0x02
PinP
0x00
Left (P&P)/Main (PinP)
0x01
Right (P&P)/Sub (PinP)
0x02
Swap*2
0x32
Picture Size (P&P)
0x00-0x0E
Yes
Yes
Disable
Enable
0x33
Sub Picture Size (PinP)
0x00
Yes
Yes
Disable
Enable
0x34
Picture Position (PinP)*3
Yes
Yes
Disable
Enable
Large
0x01
Small
0x00
Position1
0x01
Position2
0x02
Position3
0x03
Position4
(Continued)
6
FWD-50PX2
Code Table(1-a)
[a]Function
0x35
[b]Range/Switch Code
PAP Input Detect*2
(Left/Main)
0x0A INPUT2 RGB
Command
Control
Enquiry
Standby
Power On
No
Yes
Disable
Enable
No
Yes
Disable
Enable
0x0B INPUT2 COMPONENT
0x0C OPTION1 VIDEO
0x0D OPTION1 S VIDEO
0x0E OPTION1 RGB
0x0F OPTION1 COMPONENT
0x36
PAP Input Detect*2
(Right/Sub)
0x10
OPTION2 VIDEO
0x11
OPTION2 S VIDEO
0x12
OPTION2 RGB
0x13
OPTION2 COMPONENT
0x20
INPUT1 DVI
0x0A INPUT2 RGB
0x0B INPUT2 COMPONENT
0x0C OPTION1 VIDEO
0x0D OPTION1 S VIDEO
0x0E OPTION1 RGB
0x0F OPTION1 COMPONENT
0x10
OPTION2 VIDEO
0x11
OPTION2 S VIDEO
0x12
OPTION2 RGB
0x13
OPTION2 COMPONENT
0x20
INPUT1 DVI
*1: Transmit the next command 10 seconds after Power On and Power Off commands are transmitted. If not, correct data may not be able to be acquired.
*2: The command of Option 2 slot is assigned to Option 1 slot because the BKM-FW32 is installed in Option 2 slot.
*3: The Picture Position arrangement is as shown below.
1
2
3
4
IP Address
Syntax
Header
Category
Function
Data1
Data2
Data3
Data4
Data5
Check Sum
Control
0x8C
0x00
0x42
0x05
Address
00x00-0xFF
Address 1
0x00-0xFF
Address 2
0x00-0xFF
Address 3
0x00-0xFF
0xXX
Answer
Header
Answer
Check Sum
Control
0x70
0x00
0x70
Completed
0x70
0x03
0x73
Command Canceled
IP Address ex)
192.128.14.1 → 192 (0xC0) Address 0
128 (0x80) Address 1
14 (0x0E) Address 2
1
(0x01) Address 3
* IP Address command can be carried out even in the standby state.
FWD-50PX2
7
Code Table(1-a)
[a]Function
0x42
IP Address
0x45
Control Mode
[b]Range/Switch code
0x00 Main+Remocon
Command
Control
Enquiry
Standby
Power On
Yes
Yes
Enable
Enable
Yes
Yes
Disable
Enable
Yes
Yes
Enable
Enable
Yes
Yes
Enable
Enable
Yes
Yes
Enable
Enable
0x01 Main
0x02 Remocon
0x03 Both Disable
0x46
On Off Timer Mode
0x47
On Timer Enable
0x00 Every Day
0x01 Day Of Week
0x48
Off Timer Enable
bit0
Sunday 1: Enable, 0: Disable
bit1
Monday 1: Enable, 0: Disable
bit2
Tuesday 1: Enable, 0: Disable
bit3
Wednesday 1: Enable, 0: Disable
bit4
Thursday 1: Enable, 0: Disable
bit5
Friday 1: Enable, 0: Disable
bit6
Saturday 1: Enable, 0: Disable
bit7
Every day 1: Enable, 0: Disable
bit0
Sunday 1: Enable, 0: Disable
bit1
Monday 1: Enable, 0: Disable
bit2
Tuesday 1: Enable, 0: Disable
bit3
Wednesday 1: Enable, 0: Disable
bit4
Thursday 1: Enable, 0: Disable
bit5
Friday 1: Enable, 0: Disable
bit6
Saturday 1: Enable, 0: Disable
bit7
Every day 1: Enable, 0: Disable
IP Address Setting
IP Address
Syntax
Header
Category
Function
Data1
Data2
Data3
Data4
Data5
Check Sum
Control
0x8C
0x00
0x42
0x05
Address 0
0x00-0xFF
Address 1
0x00-0xFF
Address 2
0x00-0xFF
Address 3
0x00-0xFF
0xXX
Subnet Mask
Syntax
Header
Category
Function
Data1
Data2
Data3
Data4
Data5
Check Sum
Control
0x8C
0x00
0x61
0x05
Address 0
0x00-0xFF
Address 1
0x00-0xFF
Address 2
0x00-0xFF
Address 3
0x00-0xFF
0xXX
Gateway Address
8
Syntax
Header
Category
Function
Data1
Data2
Data3
Data4
Data5
Check Sum
Control
0x8C
0x00
0x62
0x05
Address 0
0x00-0xFF
Address 1
0x00-0xFF
Address 2
0x00-0xFF
Address 3
0x00-0xFF
0xXX
FWD-50PX2
DNS Primary
Syntax
Header
Category
Function
Data1
Data2
Data3
Data4
Data5
Check Sum
Control
0x8C
0x00
0x63
0x05
Address 0
0x00-0xFF
Address 1
0x00-0xFF
Address 2
0x00-0xFF
Address 3
0x00-0xFF
0xXX
DNS Secondary
Syntax
Header
Category
Function
Data1
Data2
Data3
Data4
Data5
Check Sum
Control
0x8C
0x00
0x64
0x05
Address 0
0x00-0xFF
Address 1
0x00-0xFF
Address 2
0x00-0xFF
Address 3
0x00-0xFF
0xXX
Answer
Header
Answer
Check Sum
Control
0x70
0x00
0x70
Completed
0x70
0x03
0x73
Command Canceled
IP Address ex)
192.128.14.1 → 192 (0xC0) Address 0
128 (0x80) Address 1
14 (0x0E) Address 2
1
(0x01) Address 3
* IP Address command can be carried out even in the standby state.
Code Table(1-a)
[a]Function
[b]Range/Switch code
Command
Control
Enquiry
Standby
Power On
0x42
IP Address
Yes
Yes
Enable
Enable
0x61
Subnet Mask
Yes
Yes
Enable
Enable
0x62
Gateway Address
Yes
Yes
Enable
Enable
0x63
DNS Primary
Yes
Yes
Enable
Enable
0x64
DNS Secondary
Yes
Yes
Enable
Enable
(b) Color Matrix
Syntax Header Category
Function
Data1
Data2
Data3
Data3
Check Sum
Control
Code Table(1-b)[a]
0x04
Code Table(1-c)
Code Table(1-b)[b]
Code Table(1-d)
0xXX
0x8C
0x00
Syntax
Header
Category
Function
Data1
Data2
Check Sum
Enquiry
0x83
0x00
Code Table(1-b)[a]
Code Table(1-c)
Code Table(1-d)
0xXX
Answer
Header
Answer
Check Sum
Control
0x70
0x00
0x70
Completed
0x70
0x03
0x73
Command Canceled
Answer Header Answer Return to Data Size
Return Data1
Enquiry
Code Table(1-c) Code Table(1-b)[b] Code Table(1-d) 0xXX
FWD-50PX2
0x70
0x00
0x04
Return Data2
Return Data3
Check Sum
Completed
9
Code Table(1-b)
[a]Function
0x1D
[b]Range/Switch code
Color Matrix
0x00
YCbCr
0x01
YPbPr
Command
Control
Enquiry
Standby
Power On
Yes
Yes
Disable
Enable
Code Table(1-c)
Format Select
0x00
480p
0x01
1080i
0x02
720p
0x03
480i
Code Table(1-d)
Input Select
0x00
Input2
0x01
Option1
0x02
Option2
(c) Time Control
Clock Set (Hour, Minute)
Syntax
Header
Category
Function
Data1
Data2
Data3
Check Sum
Control
0x8C
0x00
0x22
0x03
Hour: 0x00-0x17
Minute: 0x00-0x3B
0xXX
Syntax
Header
Category
Function
Data1
Data2
Check Sum
Enquiry
0x83
0x00
0x22
0xFF
0xFF
0xA3
Answer
Header
Answer
Check Sum
Control
0x70
0x00
0x70
Completed
0x70
0x01
0x71
Limit Over
0x70
0x02
0x72
Limit Under
0x70
0x03
0x73
Command Canceled
Answer
Header
Answer
Return to Data Size
Return Data1
Return Data2
Check Sum
Enquiry
0x70
0x00
0x03
Hour: 0x00-0x17*
Minute: 0x00-0x3B
0xXX
Completed
* Data of Hour: 0x80 and Minute: 0x00 is set as Return Data when a timer is not set after factory setting.
10
FWD-50PX2
Clock Set (Week)
Syntax
Header
Category
Function
Data1
Data2
Check Sum
Control
0x8C
0x00
0x23
0x02
Week: Code Table(1-e)
0xXX
Syntax
Header
Category
Function
Data1
Data2
Check Sum
Enquiry
0x83
0x00
0x23
0xFF
0xFF
0xA4
Answer
Header
Answer
Check Sum
Control
0x70
0x00
0x70
Completed
0x70
0x01
0x71
Limit Over
0x70
0x02
0x72
Limit Under
0x70
0x03
0x73
Command Canceled
Answer
Header
Answer
Return to Data Size
Return Data1
Check Sum
Enquiry
0x70
0x00
0x02
Week: FCode Table (1-e)
0xXX
Completed
Code Table(1-e)
Week Select
0x00
Sunday
0x01
Monday
0x02
Tuesday
0x03
Wednesday
0x04
Thursday
0x05
Friday
0x06
Saturday
On Timer, Off Timer
Syntax
Header
Category
Function
Data1
Data2
Data3
Check Sum
Control
0x8C
0x00
Code Table(1-f)[a]
0x03
Hour: 0x00-0x17
Minute: 0x00-0x3B
0xXX
Syntax
Header
Category
Function
Data1
Data2
Check Sum
Enquiry
0x83
0x00
Code Table(1-f)[a]
0xFF
0xFF
0xXX
Answer
Header
Answer
Check Sum
Control
0x70
0x00
0x70
Completed
0x70
0x01
0x71
Limit Over
0x70
0x02
0x72
Limit Under
0x70
0x03
0x73
Command Canceled
Answer
Header
Answer
Return to Data Size
Return Data1
Return Data2
Check Sum
Enquiry
0x70
0x00
0x03
Hour: 0x00-0x17
Minute: 0x00-0x3B
0xXX
FWD-50PX2
Completed
11
Code Table(1-f)
[a]Function
[b]Range/Switch code
Command
Control
Enquiry
Standby
Power On
Yes
Yes
Disable
Enable
Yes
Yes
Disable
Enable
Yes
Yes
Disable
Enable
Yes
Yes
Disable
Enable
Picture Inversion
0x20
Invert Start Time
0x21
Invert End Time
Clock Set
0x22
Hour, Minute
0x23
Week
On Timer
0x50
Sunday
0x51
Monday
0x52
Tuesday
0x53
Wednesday
0x54
Thursday
0x55
Friday
0x56
Saturday
0x57
Every day
Off Timer
0x58
Sunday
0x59
Monday
0x5A
Tuesday
0x5B
Wednesday
0x5C
Thursday
0x5D
Friday
0x5E
Saturday
0x5F
Every day
5. Picture/Sound
(a) Picture/Sound
Syntax
Header
Category
Function
Data1
Data2
Check Sum
Control
0x8C
0x10
Code Table(2-a)[a]
0x02
0Code Table(2-a)[b]
0xXX
Enquiry
0x83
0xFF
0xFF
0xXX
Answer
Header
Answer
Check Sum
Control
0x70
0x00
0x70
Completed
0x70
0x01
0x71
Limit Over
0x70
0x02
0x72
Limit Under
0x70
0x03
0x73
Command Canceled
Answer
Header
Answer
Return to Data Size
Return Data1
Check Sum
Enquiry
0x70
0x00
0x02
Code Table(2-a)[b]
0xXX
12
Completed
FWD-50PX2
Code Table(2-a)
[a]Function
[b]Range/Switch code
Command
Control
Enquiry
Standby
Power On
0x00
Contrast
0x00-0x64
Yes
Yes
Disable
Enable
0x01
Brightness
0x00-0x64
Yes
Yes
Disable
Enable
0x02
Chroma
0x00-0x32
Yes
Yes
Disable
Enable
0x03
Phase
0x00-0x64
Yes
Yes
Disable
Enable
0x04
Color Temp
0x00
Cool
Yes
Yes
Disable
Enable
0x01
Natural
0x02
Warm
0x03
Color1
0x04
Color2
0x05
Color3
Yes
Yes
Disable
Enable
Yes
Yes
Disable
Enable
Yes
Yes
Disable
Enable
Yes
Yes
Disable
Enable
Yes
Yes
Disable
Enable
0x09
Sharpness
0x00-0x14
0x0A
NR
0x00
OFF
0x01
Low
0x02
Mid
0x03
High
0x00
OFF
0x01
ON
0x00
High
0x01
Mid
0x02
Low
0x0C
Dynamic Picture
0x0E
Gamma Correct
0x10
Picture Mode
0x00
Standard
0x01
Vivid
0x02
User1
0x03
User2
0x04
User3
0x30
Volume
0x00-0x64
Yes
Yes
Enable
Enable
0x31
Treble
0x00-0x64
Yes
Yes
Disable
Enable
0x32
Bass
0x00-0x64
Yes
Yes
Disable
Enable
0x33
Balance
0x00-0x64
Yes
Yes
Disable
Enable
0x34
Surround
0x00
OFF
Yes
Yes
Disable
Enable
0x01
Hall
0x02
Simulate
FWD-50PX2
13
(b) Color Temp
Syntax
Header
Category
Function
Data1
Data2
Data3
Check Sum
Control
0x8C
0x10
Code Table(2-b)[a]
0x03
Code Table(2-c)
Code Table(2-b)[b]
0xXX
Syntax
Header
Category
Function
Data1
Data2
Check Sum
Enquiry
0x83
0x10
Code Table(2-b)[a]
Code Table(2-c)
0xFF
0xXX
Answer
Header
Answer
Check Sum
Control
0x70
0x00
0x70
Completed
0x70
0x03
0x73
Command Canceled
Answer
Header
Answer
Return to Data Size
Return Data1
Return Data2
Check Sum
Enquiry
0x70
0x00
0x03
Code Table(2-c)
Code Table(2-b)[b]
0xXX
Completed
Code Table(2-b)
[a]Function
[b]Range/Switch code
0x05
Red Gain
0x00-0x1E
0x06
Green Gain
0x00-0x1E
0x07
Blue Gain
0x00-0x1E
Command
Control
Enquiry
Standby
Power On
Yes
Yes
Disable
Enable
Code Table(2-c)
Format Select
0x03
Color1
0x04
Color2
0x05
Color3
6. Size/Shift
(a) 8Bits Register
Syntax
Header
Category
Function
Data1
Data2
Check Sum
Control
0x8C
0x20
Code Table(3-b)[a]
0x02
Code Table(3-b)[b]
0xXX
Enquiry
0x83
0xFF
0xFF
0xXX
Answer
Header
Answer
Check Sum
Control
0x70
0x00
0x70
Completed
0x70
0x01
0x71
Limit Over
0x70
0x02
0x72
Limit Under
0x70
0x03
0x73
Command Canceled
14
FWD-50PX2
Answer
Header
Answer
Return to Data Size
Return Data1
Check Sum
Enquiry
0x70
0x00
0x02
Code Table(3-b)[b]
0xXX
Completed
Code Table(3-b)
[a]Function
[b]Range/Switch code
Command
Control
Enquiry
Standby
Power On
0x00
H Size
0x00-0x3C
Yes
Yes
Disable
Enable
0x01
H Shift
0x00-0x3C
Yes
Yes
Disable
Enable
0x02
V Size
0x00-0x3C
Yes
Yes
Disable
Enable
0x03
V Shift
0x00-0x3C
Yes
Yes
Disable
Enable
0x04
Aspect
Yes
Yes
Disable
Enable
Yes
Yes
Disable
Enable
Yes
No
Disable
Enable
Yes
Yes
Disable
Enable
Yes
Yes
Disable
Enable
Yes
Yes
Disable
Enable
Yes
Yes
Disable
Enable
Yes
Yes
Disable
Enable
0x05
Multi Display
0x00
Wide Zoom
0x01
Zoom
0x02
Full
0x03
Sub Title
0x04
Normal
0x00
OFF
0x01
x2
0x02
x3
0x03
x4
Execute
0x06
Auto Adjust
0xFF
0x07
Dot Phase
0x00-0x1F
0x08
Auto Wide
0x00
OFF
0x01
Auto
0x00
Normal
0x01
Wide Zoom
0x00
Position1
0x01
Position2
0x02
Position3
0x03
Position4
0x00
Position1
0x01
Position2
0x02
Position3
0x03
Position4
0x04
Position5
0x05
Position6
0x06
Position7
0x07
Position8
0x08
Position9
0x09
4:3 Mode
0x0B
Multi Position (x2)*
0x0C
FWD-50PX2
Multi Position (x3)*
15
Code Table(3-b)
[a]Function
0x0D
0x0E
[b]Range/Switch code
Multi Position (x4)*
Over Scan
0x00
Position1
0x01
Position2
0x02
Position3
0x03
Position4
0x04
Position5
0x05
Position6
0x06
Position7
0x07
Position8
0x08
Position9
0x09
Position10
0x0A
Position11
0x0B
Position12
0x0C
Position13
0x0D
Position14
0x0E
Position15
0x0F
Position16
0x00
OFF
0x01
ON
Command
Control
Enquiry
Standby
Power On
Yes
Yes
Disable
Enable
Yes
Yes
Disable
Enable
* Arrangement of Multi Position.
Multi Position (x2)
Multi Position (x3)
Multi Position (x4)
1
2
1
2
3
1
2
3
4
3
4
4
5
6
5
6
7
8
7
8
9
9
10
11
12
13
14
15
16
7. Status Enquiry
(a) Model Name
Syntax
Header
Category
Function
Data1
Data2
Check Sum
Enquiry
0x83
0x30
0x00
0xFF
0xFF
0xB1
Answer
Header
Answer
Return to Data Size
Return Data1
Check Sum
Enquiry
0x70
0x00
0x02
Code Table(4-a)
0xXX
Completed
Code Table(4-a)
Format Select
0x23
16
FWD-50PX2
FWD-50PX2
(b) Serial Number
Syntax
Header
Category
Function
Data1
Data2
Check Sum
Enquiry
0x83
0x30
0x01
0xFF
0xFF
0xB2
Answer Header
Answer
Return to
Data Size
Return Data1
Return Data2
Return Data3 Return Data4 Check Sum
Enquiry
0x00
0x05
Upper 8bit
Data
MiddleUpper
Data
MiddleLower
Data
0x70
Lower 8bit
Data
0xXX
Completed
Return Data1-Data4: 0x001E8480_0x002DC6BF (2,000,000-2,999,999)
(c) Operation Time
Syntax
Header
Category
Function
Data1
Data2
Check Sum
Enquiry
0x83
0x30
0x02
0xFF
0xFF
0xB3
Answer Header
Answer
Return to
Data Size
Return Data1
Return Data2
Return Data3 Return Data4 Check Sum
Enquiry
0x00
0x05
Upper 8bit
Data
MiddleUpper
Data
MiddleLower
Data
0x70
Lower 8bit
Data
0xXX
Completed
Return Data1-Data4: 0x00000000_0xD693A3FF (0sec.-3,599,999,999sec.)
(d) Soft Version (Main CPU)
Syntax
Header
Category
Function
Data1
Data2
Check Sum
Enquiry
0x83
0x30
0x03
0xFF
0xFF
0xB4
Answer
Header
Answer
Return to Data Size
Return Data1
Return Data2
Check Sum
Enquiry
0x70
0x00
0x03
Upper 8bit Data
Lower 8bit Data
0xXX
Completed
Return Data1_Data2: 0x0000_0xFFFF
ex) In Version0.100, it is set to 01 and 00.
(e) 8bits Register
Syntax
Header
Category
Function
Data1
Data2
Check Sum
Enquiry
0x83
0x30
Code Table(4-b)
0xFF
0xFF
0xXX
Answer
Header
Answer
Return to Data Size
Return Data1
Check Sum
Enquiry
0x70
0x00
0x02
Code Table(4-b)
0xXX
Completed
Code Table(4-b)
Function
0x07
Return Data
Digital 3.3 V
0x00-0xFF
0x09
Digital 5 V
0x00-0xFF
0x0A
Temp1
0x00-0xFF
0x10
Analog 5 V/9 V
0x00-0xFF
FWD-50PX2
Unit
5 V voltage out
17
(f) Shutdown Log
Syntax
Header
Category
Function
Data1
Data2
Check Sum
Enquiry
0x83
0x30
0x11
0xFF
0xFF
0xC2
Answer
Header
Answer
Return to Data Size
Return Data1
Check Sum
Enquiry
0x70
0x00
0x02
Shutdown Log
Code Table(4-c)
0xXX
Completed
Return Data1: 0x00–0xFF
Code Table(4-c)
Shutdown Information
bit0
Reserved
bit1
1: FAN movement abnormal
0: Normal
bit2
1: Panel communication abnormal
0: Normal
bit3
1: Temperature sensor abnormal
0: Normal
bit4
1: Main power abnormal
0: Normal
bit5
1: Digital power abnormal (3.3 V, 5 V)
0: Normal
bit6
1: Analog power abnormal (12 V, 9 V)
0: Normal
bit7
Reserved
18
FWD-50PX2
Code Table(4-d)
[a]Function
[b]Range/Switch code
Command
Control
Enquiry
Standby
Power On
0x00
Model Name
0x08-0x09
No
Yes
Enable
Enable
0x01
Serial Number
0x001E8480-0x002DC6BF
Yes
Yes
(2,000,000_2,999,999)
Enable
Enable
0x02
Operation Time
0x00000000-0xD693A3FF
(0sec._3,599,999,999sec.)
Yes
Yes
Enable
Enable
0x03
Soft Version (Main)
0x0000-0xFFFF
No
Yes
Enable
Enable
0x07
Digital 3.3 V
0x00-0xFF
No
Yes
Enable
Enable
0x08
MainPower (Vs)
0x00-0xFF
No
Yes
Enable
Enable
0x09
Digital 5 V
0x00-0xFF
No
Yes
Enable
Enable
0x0A
Temp1
0x00-0xFF
No
Yes
Enable
Enable
0x0B
Temp2
0x00-0xFF
No
Yes
Enable
Enable
0x0C
Temp3
0x00-0xFF
No
Yes
Enable
Enable
0x10
Analog9 V
0x00-0xFF
No
Yes
Enable
Enable
0x11
Shutdown Log
0x00-0xFF
No
Yes
Enable
Enable
0x12
Digital 3.3 V (Failure)
0x00-0xFF
No
Yes
Enable
Enable
0x13
Digital 5 V (Failure)
0x00-0xFF
No
Yes
Enable
Enable
0x14
Analog 5 V/9 V (Failure) 0x00-0xFF
No
Yes
Enable
Enable
0x15
MainPower (Va)
0x00-0xFF
No
Yes
Enable
Enable
0x16
AnalogPower 12 V
0x00-0xFF
No
Yes
Enable
Enable
8. User Reset
Syntax
Header
Category
Function
Data1
Data2
Check Sum
Control
0x8C
0x50
Code Table(5)
0x02
0xFF
0xXX
Answer
Header
Answer
Check Sum
Control
0x70
0x00
0x70
Completed
0x70
0x03
0x73
Command Canceled
Code Table(5)
Function
Range/Switch code
Command
Control
Enquiry
Standby
Power On
Yes
No
Disable
Enable
0x00
Picture Reset
0x01
Audio Reset
Yes
No
Disable
Enable
0x02
Size Reset
Size, Shift, Dot Clock, Phase
Yes
No
Disable
Enable
0x03
Picture Reset2
Contrast, Brightness, Chroma, Phase
Yes
No
Disable
Enable
0x04
All Reset
Yes
No
Disable
Enable
FWD-50PX2
19
The material contained in this manual consists of
information that is the property of Sony Corporation.
Sony Corporation expressly prohibits the duplication of
any portion of this manual or the use thereof for any
purpose other than the operation or maintenance of the
equipment described in this manual without the express
written permission of Sony Corporation.
Le matériel contenu dans ce manuel consiste en
informations qui sont la propriété de Sony Corporation.
Sony Corporation interdit formellement la copie de
quelque partie que ce soit de ce manuel ou son emploi
pour tout autre but que des opérations ou entretiens de
l’équipement à moins d’une permission écrite de Sony
Corporation.
Das in dieser Anleitung enthaltene Material besteht aus
Informationen, die Eigentum der Sony Corporation sind.
Die Sony Corporation untersagt ausdrücklich die
Vervielfältigung jeglicher Teile dieser Anleitung oder den
Gebrauch derselben für irgendeinen anderen Zweck als
die Bedienung oder Wartung der in dieser Anleitung
beschriebenen
Ausrüstung
ohne
ausdrückliche
schriftliche Erlaubnis der Sony Corporation.
FWD-50PX2
FWD-50PX2 (SY) E
9-878-389-01
Sony Corporation
Printed in Japan
2005. 10 22
©2005
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement