advertisement
Rev. 1.0
MODEL : STm.57b
MOBILE PRINTER
All specifications are subject to change without notice
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.
DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTION
Table of Contents
1. Unpacking
2. Product overview
3. Installation & Usage
3-1. Control Panel Usage
3-2. Battery Installation
3-3. Battery removel
3-4. Battery Charging
3-5. Battery Charger Usage
3-6. Usage of Cigar Jack for charging
3-7. Belt clip usage
3-8. Roll Paper Installation
3-9. Leather case Usage
3-10. Shoulder Strap Usage
3-11. Self Test
4. Peripherals Connection
4-1. Bluetooth connectiontion
4-2. Interface Cable Connection
5. Printer Cleaning
6. Product Specification
6-1. Specification
7. CPCL Command Compatibility
10
11
12
13
8
9
6
7
4
5
2
3
4
18
19
20
20
22
14
17
17
1
1. Unpacking
Standard
Printer Battery
Belt Buckle
Recharger
USB Shelded Cable
Serial Cable
Roll paper
Optional
CD
Quick Manual
2
Battery Holder
(Cradle)
Cigar jack Printer case shoulder strap
2. Product overview
Front
Power switch
Paper feed button
Side
USB
SERIAL
Cover open button
Charger
Connector
Battery
3
3. Setting Up the Product
3-1. Control Panel Usage
3-2. Installing battery
4
Button Name function
Power button
This button is used to turn the printer on and off.
When the printer is off, press this button for approximately
2 seconds and it will turn on the power. When you press this button in a state that the printer is on, the printer will turn off.
Paper
Feed
Button
Battery
Status
Lamp
Paper output can be done manually by pressing this button.
Additionally, self-testing and Hexadecimal Dumping can be processed..
1. Refer to “3-10” for self test information.
2. Refer to the service manual regarding Hexadecimal Dumping.
1. If the Batt, LED are Lit, the battery is fully charged.
2. If you can hear beeping sound and LED light is turned off, it means
that the battery is at the lowest level.
3. If the battery is not charged at all, the printer turns off automatically.
Error
Lamp
If the red light is turned on, it means that the paper cover is open.
Push the Open to the direction as pointed by arrow in the image.
1 2
3
Open the battery cover and push up the hook to the direction as above.
Insert the battery inside printer as shown.
Close the battery cover once you inserted the battery completely.
NOTE
As the battery is not charged at the time of your purchase, charge the battery prior to using the product.
(Use the battery charger and/or the optional battery holder.)
5
6
3-3. Battery removel
Push the Open into the direction indicated with the arrow in the image.
1 2
3
Push up the hook after opening the battery cover.
Pull out the battery as shown above.
3-4. Battery Charging
②
LED
①
1. The battery can be charged only when the temperature is 0~40℃
2. Be sure that the printer is turn off and the battery to be charged is installed.
3. Connect the charger to the printer.
4. Recharging will now be started.
3-4-1 The status of lamp in charging
Status charging charging complete
Charging Lamp
Red
Green
NOTE
1. Unless the exclusive charger is used provided by the manufacturer, the printer
can be damaged, and the manufacturer is not liable for the consequential damage.
2. Before removing the battery, make sure that power is turned off.
3. Printer does not work in the status of being connected with charger only.
4. The battery should be installed to operate printer.
5. While charging, do not turn on the power.
6. Do not operate the print while charging the battery.
7. Do not connect the charger while the printer is operated.
7
8
3-5. Battery charger Usage
Optional
②
LED
①
1. Please press the battery into the holder until you can hear a snapping sound.
2. Insert DC JACK ① into the end completely as the direct shown above.
3. Plug the power code to electrical outlet.
4. While charging the battery, red light turns on.
Once the charge is completed, green light turns on.
Check the state of code connection when error occurs blinking on red light.
3-5-1 The status of lamp in charging
Status charging charging complete
Charging Lamp
Red
Green
NOTE
In the case the battery is not fixed properly in the holder, the red lamp will be blinking,
Then, extract and reinsert the battery.
3-6 Usage of Cigar Jack Charger for charging
Optional
Printer
Battery holder
Connect the car cigar JACK charger into the printer or battery holder.
Input
Output
12 ~ 24V
8.4V 0.8 ~ 1.2A
NOTE
Use the Cigar Jack offered by the manufacturer .
9
3-7. Belt clip Usage
3-8. Roll Paper Installation
Insert the belt hook screw into the hole of the belt hook.
1
2
Open the paper cover pressing the open button. Insert a sharp tool into the paper guide hole and push it in the direction of arrow as shown above.
1 2
3 4
Put the paper in the right direction after adjusting the paper guide matching the paper width. (Remove the paper core when it is used all)
10
As shown above, fasten the screw with a screw driver.
Pull out a short length of the paper and shut the paper cover.
Press the Feed Key once to arrange the paper.
11
3-9. Leather Case Usage
Optional
3-10. Shoulder Strap Usage
Optional
12
Open the Velcro
1 2
3
Put the printer into the leather case following the direction shown in the image.
Insert the strap into the hook on the printer.
1 2
3 4
Place the end of strap into the hook of shoulder strap.
Close the Velcro
After pulling out the end of strap tightly, put it into the clip to be fastened.
Fasten the strap in the opposite side with the sample way.
13
3-11. Self Test
14
Turn off the power pressing the power button for approximately
3 seconds.
While you are pressing the FEED button, press the power button
1 2
3
NOTE
1. To print ASCII pattern additionally,
press the Feed button once more
2. After printing ASCII pattern, the
self test will be finished automatically.
3. If the Feed button is not pressed
to print ASCII pattern, self test will be
finished automatically after 30 seconds.
The printout is produced.
The sample of self test printout
15
16
When the printer is installed initially or when you face a problem, you can run the self test and check the information about
-Control Circuit, Mechanism, Print Quality, ROM Version
After checking with self-test and no issues are found, you can examine other devices and software. This function is working independent of devices and software.
●
Motor protection from being overheated
The motor should be stopped and cooled about more than 30 seconds after
continuous printing 1.5 meter
4. Peripherals Connection
This product can communicate with other devices via Bluetooth communication and cable.
4-1. Bluetooth Connection
1. The Printer can be connected to devices equipped with Bluetooth communication
capacity (PDAs, PCs, etc.)
2. Use the Bluetooth connection function supported by the device to connect to the printer.
NOTE
Refer to the Bluetooth Manual for more details on connection.
17
18
4-2. Interface Cable Connection
Serial
USB
1. Connect USB or Serial cable into the cable connector on the printer.
NOTE
Use the cable offered by the manufacturer (USB, Serial)
2. Connect the interface cable into the USB or Serial port of the device
(PDA, PC, etc.)
5. Printer cleaning
If the interior of the printer is dusty, printing quality can lowered.
In such a case, follow the instructions below to clean up the printer.
NOTE
1. Make sure to turn the printer power off prior to cleaning
2. Regarding print head cleaning, as the print head sets very hot during
printing, turn off the printer power and wait approximately 10 minute before
commencement.
3. When cleaning the print head, take care not to touch the heated portion of the
print head. The print head subject to be damaged by static electricity.
4. Take care not to allow the print head to become scratched and /or
damaged in any way.
1. Use an applicator swab moistened with an alcohol solution to clean the print
head and remove any dusts.
2. Once the cleaning is completed, insert paper roll into the printer few minutes
later and close the printer cover.
Preventing Overheating
To prevent the motor from overheating, continuous driving of the printer
should be 1.5 m or less in print length. Set the pause time for 30 seconds
or more after driving the printer.
19
20
6. Pritner Specification
6-1. Specification
Printing Method
Printing Speed
Resolution
Character
Barcode
Emulation
Driver
Sensor
Paper
Reliability paper type width thickness
External Diameter
Internal Diameter
TPH
Battery
Communications standard
Battery Charger
Battery
Size input output
Battery type output
Charging time
WXDXH(mm)
WXDXH”
Direct Thermal
80mm/sec
203 DPI X 203 DPI
ALPHA NUMERIC Character, Extension Character
Code 39, Code 93, UCC/EAN-128, Code 128,
UPC-E, UPC-A, EAN-8, EAN-13, EAN-14, UPC and
EAN 2 or 5 digit extensions, Plessey, FIM, Postnet,
Interleaved 2-of-5, MSI, Codabar
CPCL
Window CE 4.2&5.0, Window Mobile 5.0
Black-mark, Gap, cover open
Thermal Paper
58mm
65㎕
Max. Φ 56mm
12.5mm +/-0.5mm
100km
Continuous Printing 54min
Standby for 19hours
Printing length: 249.8M
Serial(RS-232C), USB, Bluetooth Class2
AC100~240V, 50/6 Hz
8.4V , 800~1400mA
Li-ion
7.4V, 2200mAh
3hours 40min
104 X 74 X 154
4.0 X 2.9 X 6.0
Weight
Environmental sealing
Temperature
Humidity operation storage operation storage
500g
IP42
5~40℃
-20~60℃
35 ~ 80%
10 ~ 90%
21
22
7. CPCL Command Compatibility
NOTE
Compatible
○
Compatible with only commanders provided by the manufacturer.
●
Partially
Compatible
△
Not
Compatible x
Printer Commands
FORM
JOURNAL
UNITS
Comments
TEXT
TEXT
FONT-GROUP(FG)
TEXT CONCATENATION
MULTILINE(ML)
COUNT
SETMAG
SCALABLE TEXT
Linear Bar Codes
BARCODE
BARCODE-TEXT
Two-Dimensional Bar Codes
PDF417 (PORTABLE DATA FILE)
MAXICODE
QRCODE
DATAMATRIX
GS1(RSS)
Compatibility
○
○
○
○
○
Compatibility
○
○
○
○
○
○
X
Compatibility
○
○
Compatibility
○
○
●
●
●
Graphics
BOX
LINE
INVERSE-LINE
PATTERN
GRAPHICS
PCX
Advanced Commands
CONTRAST
TONE
JUSTIFICATION
PAGE-WIDTH
PACE
NO-PACE
WAIT
REWIND
TENSION
SPEED
SETSP
ON-OUT-OF-PAPER
ON-FEED
PREFEED
POSTFEED
PRESENT-AT
COUNTRY/CODE PAGE
FORMAT FILES
BEEP
CUT
PATIAL-CUT
MCR
○
○
X
○
○
○
○
○
○
○
X
X
X
○
○
○
X
X
●
Compatibility
○
○
○
○
○
○
Compatibility
○
○
○
23
24
Line Print Mode
SETLP
SETLF
Moving With X and Y Coordinates
LMARGIN
SETBOLD
SETSP
Special ASCII Characters
SETFF
SET-TOF
SETLP-TIMEOUT
Compatibility
○
○
○
○
○
○
○
○
○
○
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project