Stanton C.502 CD Player User Manual

Stanton C.502 CD Player User Manual
C.502
/
/
USER MANUAL
IMPORTANT SAFETY PREC AUTIONS
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15. Servicing - The user should not attempt any service to the appliance
beyond that described in the operating instructions. All other servicing
should be referred to qualified service personnel..
16. Ventilation - Slots and openings in the cabinet are provided for
ventilation and to ensure reliable operation of the product and to
protect it from overheating, and these openings must not be blocked
or covered. The openings should never be blocked by placing the
product on a bed, sofa, rug, or other similar surface. This product
should not be placed in a built-in installation such as a bookcase or
rack unless proper ventilation is the manufacturers instructions have
been adhered to.
17. Attachments - Do not use attachments not recommended by the product
manufacturer as they may cause hazards.
18. Accessories - Do not place this product on an unstable cart, stand,
tripod, bracket, or table. The product may fall, causing serious injury
to a child or adult, and serious damage to the product. Use only with a
cart, stand, tripod, bracket, or table recommended by the
manufacturer, or sold with the product. Any mounting of the product
should follow the manufacturer s instructions, and should use
amounting accessory recommended by the manufacturer.
19. Lightning - For added protection fo r this product during a lightning
storm, or when it is left unattended and unused for long periods of time,
unplug it from the wall outlet and disconnect the antenna or cable
system. This will prevent damage to the product due to lightning and
power-line surges.
20. Replacement Parts - When replacement parts are required, be sure
the service technician has used replacement parts specified by the
manufacturer or have the same characteristics as the original part.
Unauthorized substitutions may result in fire, electric shock, or other
hazards.
21. Safety Check - Upon completion of any service or repairs to this
product, ask the service technician to perform safety checks to
determine that the product is in proper operating condition.
22. This product is in compliance with EUWEEE
regulations. Disposal of end of life product should not
be treated as municipal waste. Please refer to your
local regulations for instructions on proper disposal of
this product.
23. Carts and Stands - The appliance should be used only
with a cart or stand that is recommended by the
manufacturer. An appliance and cart combination
should be moved with care. Quick stops, excessive
force, and uneven surfaces may cause the appliance
and cart combination to overturn.
24. This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:(1) this device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Read Instructions - All the safety and operating instructions should
be read before this product is operated.
Retain Instructions - The safety and operating instructions should be
retained for future reference.
Heed Warnings - All warnings on the appliance and in the operating
instructions should be adhered to.
Follow Instructions - All operating and use instructions should be
followed.
Water and Moisture - The appliance should not be used near water
- for example, near a bathtub, washbowl, kitchen sink, laundry tub, in
a wet basement, or near a swimming pool, and the like.
Wall or Ceiling Mounting - The product should be mounted to a wall
or ceiling only as recommended by the manufacturer.
Heat - Appliance should be situated away from heat sources such as
radiators, heat registers, stoves, or other appliances (including
amplifiers) that produce heat.
Power Sources - This product should be operated only from the type of
power source indicated on the rating label. If you are not sure of the
type of power supply to your home, consult your product dealer or
local power company. For products intended to operate from battery
power, or other sources, refer the operating instructions.
Grounding or Polarization - This product may be equipped with a
polarized alternating current li ne plug (a plug having one blade
wider than the other). This plug will fit into the power outlet only one
way. This is a safety feature. If you are unable to insert the plug fully
into the outlet, try reversing the plug. If the plug should still fail to fit,
contact your electrician to replace your obsolete outlet. Do not defeat
the safety purpose of the polarized plug.
Power-Cord Protection - Power-supply cords should be routed so
that they are not likely to be walked on or pinched by items placed
upon or against them, paying particular attention to the cord in
correspondence of plugs, convenience receptacles, and the point
where they exit from the appliance.
Cleaning - The appliance should be cleaned only as recommended by
the manufacturer. Clean by wiping with a cloth slightly damp with
water. Avoid getting water inside the appliance.
Non-use Periods - The power cord of the appliance should be
unplugged from the outlet when left unused for a long period of time.
Object and Liquid Entry - Care should be taken so that objects do
not fall and liquids are not spilled into the enclosure through openings.
Damage Requiring Service - The appliance should be serviced by
qualified service personnel when:
A. The power-supply cord or the plug has been damaged; or
B. Objects have fallen, or liquid has been spilled into the appliance; or
C. The appliance has been exposed to rain; or
D. The appliance does not appear to operate normally or exhibits a
marked change in performance; or
E. The appliance has been dropped, or the enclosure damage.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: To reduce the risk of electric shock, do not remove an y
cover. No user-serviceable parts inside. Refer servicing to qualified
service personnel only.
The lightning flash with arrowhead symbol within the equilateral triangle is intended to alert the use to the
presence of un-insulated "dangerous voltage” within the products enclosure that may be of sufficient
magnitude to constitute a risk of electric shock.
The exclamation point within the equilateral triangle is intended to alert the user to the presence of important
operation and maintenance (servicing) instructions in the literature accompanying this appliance.
CAUTION: To prevent electric shock, do not use this polarized plug with an extension cord, receptacle or other outlet
unless the blades can be fully inserted to prevent blade exposure.
1
IMPORTANT TO SAFETY
WARNING:
• TO PREVENT FIRE OR SHOCK HAZARD, DO NOT
USE THIS PLUG WITH AN EXTENSION CORD,
RECEPTACLE OR OTHEROUTLET UNLESS THE
BLADES CAN BE FULLY INSERTED TO PRES ENT
BLADE EXPOSURE.
• TO PREVENT FIRE OR SHOCK HAZARD. NO NOT
EXPOSE THIS APPLIANCE TO RAIN OR NOISTURE.
• TO PREVENT ELECTRICAL SHOCK, MATCH WIDE
BLADE PLUG TO WIDE SLOT FULLY INSERT.
NOTE:
This CD player uses the semiconductor laser. To allow
you to enjoy music at a stable operation, it is recommended
to use this in a room of 5ºC 41ºF - 35ºC 95ºF.
RATING LABEL
CAUTION:
1. Handle the power supply cord carefully
Do not damage or deform the power supply cord.
If it is damaged or deformed, it may cause electric
shock or malfunction when used. When removing
from wall outlet,be sure to remove by holding the
plug attachment and not by pulling the cord.
2. In order to prevent electric shock, do not open the
top cover. If a problem occurs, contact your dealer.
3. Do not place metal objects or spill liquid inside the
CD player. Electric shock or malfunction may result.
CLASS 1 LABEL
CAUTION:
USE OF CONTROLS OR ADJUSTMENTS OR
REFORMANCE OF PROCEDURES OTHER THAN
T H O S E S P E C I F I E D H E R E I N M AY R E S U LT I N
HAZARDOUS RADIATION EXPOSURE.
THE COMPACT DISC PLAYER SHOULD NOT BE
ADJUSTED OR REPAIRED BY ANYONE EXCEPT
PROPERLY QUALIFIED SERVICE PERSONNEL.
Please, record and retain the Model name and serial
number of your set shown on the rating label.
Model No. ___________ Serial No. ___________
DOUBLE INSULATED - WHEN SERVICING , USE
ONLY IDENTICAL REPLACEMENT PARTS.
CAUTION: TO REDUCE THE RISK
OF ELECTRIC SHOCK, DO NOT
REMOVE THE COVER (OR BACK) .
THERE ARE NO SERVICEABLE
PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
NOTE:
This unit may cause interference to radio and television
reception.
Line Voltage Selection (for multiple
voltage model only)
The desired voltage may be set with the
115V
VOLTAGE SELECTOR switch on the rear
panel, using a screwdriver.
Do not twist the VOLTAGE SELECTOR
230V
switch with excessive force as this may
cause damage
If the VOLTAGE SELECTOR switch does not move
smoothly, please contact a qualified serviceman.
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to
alert the user to the presence of uninsulated
“dangerous voltage" within the product's
enclosure that may be of sufficient magnitude to constitute a risk of electric shock
to persons.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
FOR U.S.A. & CANADA MODEL ONLY
CAUTION
TO PREVENT ELECTRIC SHOCK DO NOT USE
THIS (POLARIZED) PLUG WITH AN EXTENSION
CORD, RECEPTACLE OR OTHER OUTLET UNLESS
T H E B L A D E S C A N B E F U L LY I N S E RT E D TO
PREVENT BLADE EXPOSURE.
2
NOTE ON USE
•
•
•
•
•
•
•
•
Allow for sufficient heat dispersion when installed in a rack.
Handle the power cord carefully.
Hold the plug when unplugging the cord.
Keep the set free from moisture, water, and dust.
Unplug the power cord when not using the set for long periods of time.
Do not obstruct the ventilation holes. (For sets with ventilation holes.)
Do not let foreign objects in the set.
Do not let insecticides, benzene, and thinner come in contact with the set.
Never disassemble or modify the set in any way.
For 220 volt use in USA, USA nema style 220 volt plug. For other countries, use proper plug for the local outlet.
MAIN FEATURES
(1) 8 times oversampling 1 bit D/A converter.
(2) 4 different scan speeds.
(3) Frame search.
(4) Auto cue.
(5) 20 sec Anti-shock.
(6) Pitch display.
(7) MP3 playback.
MAIN UNIT
2
1
3
2
6
5
7
(1)POWER
(2)DISC HOLDER
(3)OPEN/CLOSE
(4)REMOTE CONTROL CONNECTOR
4
5
(5)AUDIO OUT L AND R
(6)DIGITAL OUT SOCKET
(7)VOLTAGE SELECTOR (FOR DUAL VOLTAGE
ONLY)
3
MAIN FEATURES
CONTROL UNIT
/
(1)OPEN/CLOSE
(2)SINGLE/CONTINUE
(3)TIME
(4)TRACK BACKWARD
(5)+10/FOLDER
(6)TRACK FORWARD
(7)F. BACKWARD
(8)F. FORWARD
(9)PITCH SLIDER
(10)LCD
7
/
(11)LOOP IN
(12)LOOP OUT
(13)RELOOP
(14)JOG WHEEL
(15)CUE
(16)PLAY/PAUSE
(17)PITCH RANGE
(18)PITCH LOCK
(19)PITCH DOWN
(20)PITCH UP
(21)RELAY
(22)RELAY LED
(23)PITCH 4% LED
(24)PITCH 8% LED
(25)PITCH 16% LED
(26)PITCH LOCK LED
(27)FADER START CONNECTOR
(28)CONTROL CONNECTOR
7
(8) TIME BAR INDICATOR
(9) LOOP INDICATOR
(10)RELOOP INDICATOR
(11) PITCH INDICATOR
(12)PITCH METER
(13) TIME DISPLAY
(14) CHARACTER DISPLAY
(15) TOTAL REMAIN INDICATOR
(16) REMAIN INDICATOR
(17) ELAPSED INDICATOR
(1)AUTO CUE
(2) TRACK INDICATOR
(3)FOLDER/TRACK INDICATOR
(4)PLAY/PAUSE INDICATOR
(5)CUE INDICATOR
(6)SINGLE INDICATOR
(7)MP3 INDICATOR
4
1. Checking the Contents
Check that the carton contains the following items:
1) Main unit
2) Control unit
3) Operating instructions (this booklet)
4) Two pair of RCA pin cord.
5) Control cords (1 meter)
6) Power cord
7) Two fader start cables
2. Installing the Unit
Mount the unit onto your console or rack with 19" EIA rack
rails.
CAUTION:
The player will work normally when the main unit is
mounted with the front panel at within 15 degrees of the
vertical plane. If the unit is tilted excessively, discs may
not be loaded or unloaded properly.
The control panel's LCDs are designed to be
clearly visible within the angles shown in Figure 2.
Mount the control unit so that the visual angle is
within this range.
Max
15
45
5
Main unit
Control
Panel Button
Figure1
Figure2
Connections
1) Turn off the POWER switch.
2) Connect the RCA pin cord to the input on your mixer.
3) Connect the control cords to the REMOTE connector on the main unit.
CAUTION:
Be sure to use the supplied control cords. Using another type of cable may result in damage.
Be sure the power is off when connecting the control cords. Otherwise the units may not work properly.
NAMES AND FUNCTIONS
Main Unit Front Panel
(1) POWER (Power ON/OFF Switch)
When the POWER switch is pressed , the power
turns on.
(2) DISC HOLDER
Place the discs in the holder . Press the OPEN/
CLOSE button to open and close the disc holder.
(3) OPEN/CLOSE
Press it to open and close the disc holder . The
control unit also includes OPEN/CLOSE button.
The disc holder cannot be opened during playback,
so stop playback before pressing the button.
(4) REMOTE CONTROL CONNECTOR
Connect this connector to the control unit using
the included control cord.
(5) AUDIO OUT
The audio signals from each player are output
from these jacks.
(6) DIGITAL OUT SOCKET
The music signal of this socket is digital. Connect
the output to the respective digital input of a digital
amplifier for example.
5
NAMES AND FUNCTIONS
Control Unit
(1)OPEN/CLOSE
Press it to open and close the disc holder. The main
unit also includes OPEN/CLOSE buttons. The disc
holder cannot be opened during playback, so stop
playback before pressing the button.
(2) SGL/CTN (Single/Continuous Button)
Press it to switch between the single and continuous
play modes. The SINGLE mode is indicated by the
SINGLE indicator on the LCD
(3)TIME CD MODE
Press this button to switch the time display among
the elapsed time and remaining time and total
remaining time of the disc.
(4)TRACK BACKWARD
Use this button to go back to the beginning of the
current track or select a previous track for playing.
(5)+10/FOLDER
CD mode use this button to skip ahead 10 tracks.
Mp3 mode press this button to select the next folder.
(6) TRACK FORWARD
Use this button to skip to the next CD track.
(7).(8)F.FORWARD/F.BACKWARD
Press these buttons to perform scan function during
pause mode or during play mode.
(9) PITCH SLIDER
Use the slider to adjust the CD pitch . Slide up to
decrease pitch, down to increase pitch.
(10) LCD
(11) LOOP IN
Used for setting a start loop point and releasing the
loop action.
(12) LOOP OUT
Used for setting the end loop point and releasing the
loop action.
(13) RELOOP
Depending on mode, as explained further, this button
is used for either repeating a previously set loop or
seamlessly stuttering on the last set cue point.
(14)JOG WHEEL
When the dial is turned during CD pause, the
point at which the sound is being produced moves
by a number of frames corresponding to the number
of clicks.
Clockwise moves the point forward, counterclockwise
moves the point backward.
(15)CUE (Cue Button)
Press the CUE button during playback to return to
the position at which playback started.
(16)PLAY/PAUSE
Use this button to start playback. Press once to start
playback , once again to set the pause mode , and
once more to resume playback.
(17)PITCH RANGE
Choose from pitch percentages of 4%,8% and 16%.
(18)PITCH LOCK
Use this button to enable or disable BPM adjustment
with the pitch sliders. BPM adjustment with the pitch
sliders is enabled when the PITCH LED lights.
(19)PITCH DOWN
The CD slows down while this button is pressed.
Release the button to return to the original BPM.
(20)PITCH UP
The CD speeds up while this button is
pressed. Release the button to return to the
original BPM.
(21)RELAY
Press this button when Disc 1 ends the CD player
will automatically change to Disc 2 and when Disc
2 ends it will return to Disc 1,etc.
(22)RELAY LED
(23)PITCH 4%LED
(24)PITCH 8% LED
(25)PITCH 16% LED
(26)PITCH LOCK LED
(27)FADER START
Via the Control socket, the respective CD-player
can be remotely controlled. If you are using a mixer
with fader start-function connect the player with
the Control Out- socket. Please note that these
sockets must never be connected with any voltage.
(28)CONTROL CONNECTOR
Connect this connector to the REMOTE connector
on the main unit using the included control cord.
6
CONTROLS AND FUNCTIONS
7
7
1. AUTO CUE
This will indicate if the Auto Cue is on or off. Press
and hold the SGL/CTN for 1 sec. to turn the Auto Cue
function on and off.
2.TRACK INDICATOR
This 3-digit indicator displays the current track. The
number displayed in the track indicator is a direct
reference to a track being selected or a track in play,
pause, or cue mode.
3.FOLDER/TRACK INDICATOR
This indicator shows you if you are looking at the
track number or the folder number.
4.PLAY / PAUSE INDICATOR
When the unit is in play mode the “PLAY”indicator
will glow, when the drive is in pause mode the “PAUSE”
indicator will glow.
5.CUE INDICATOR
This indicator will glow when the unit is in CUE mode
and will flash every time a new CUE POINT is set.
6.SINGLE INDICATOR
This indicates that the CD drive is in single play mode.
The track will play once and return to CUE mode. If
the single indicator is not on, the unit is in continuous
mode and the drive will play all the remaining tracks
on the disc until you stop it or power is interrupted.
7.MP3 INDICATOR
This will indicate that a Mp3 disc is loaded in the drive.
8.TIME BAR INDICATOR
This bar gives a visual approximation of a track' s
or disc's remaining time. This bar will begin to flash
when a CD is ending or a track if the unit is in"
SINGLE" mode.
9.LOOP INDICATOR
Appears when the CD is repeating a particular area
with the music on the CD.
10.RELOOP INDICATOR
Appears when the CD has a loop set previously
and can go back loop again.
11.PITCH INDICATOR
Indicator will light up when the Pitch is activated.
12.PITCH METER
Shows the percentage change in pitch of the song.
The meter will display the pitch percentage applied
by the PITCH SLIDER.
13.TIME DISPLAY
This displays the Minutes, Seconds, and Frames.
The meter will display either the elapsed time, or
remaining time of a track.
14.CHARACTER DISPLAY
This will display the name of the file, artist, and title
when a Mp3 disc is loaded.
15.TOTAL REMAIN INDICATOR
When TOTAL and REMAIN are visible, this indicates
that the Time Display is showing total remaining
disc time.
16.REMAIN INDICATOR
When the REMAIN indicator is visible this indicates
that the Time Display is showing remaining track
time.
17.ELAPSED INDICATOR
It is for showing time as it is taking place.
7
1. Opening and Closing the Disc Holder
Turn the unit power on . Press the OPEN/CLOSE button to open the disc holde r. OPEN/CLOSE buttons are
provided on both the main unit and control unit.
The disc holder cannot be opened during playback to prevent playback from being interrupted if the OPEN/CLOSE
button is pressed accidentally. Stop the playback first, then press the OPEN/CLOSE button.
2. Loading discs
Hold the disc by the edges and place it in the disc holder, then press the
OPEN/CLOSE button again to close the disc holder. The unit will show the total
track number and the total playing time for about 2 seconds then enter the cue
condition, the cue point will be set to the music starting point of the first track
automatically.
Figure 2-1
CAUTION:
Do not place any foreign objects in the disc holder, and do not place more than one disc in the disc holder at a
time.
Do not push the disc holder in manually when the power is off, as this may result in malfunction and damages
the player.
3. Selecting Tracks
Press the SKIP button once to move to the next higher or lower track.
Hold the SKIP button to change tracks continuously at a higher speed.
When a new track is selected during playback , playback begins as soon as the skip search operation is completed.
If the skip
button is pressed while at the last track, the first track is selected . In the same way, if the skip
button is pressed while at the first track, the last track is selected.
4. Starting Playback
Press the PLAY/PAUSE button during the pause or cue condition to start playback. The PLAY indicator will light.
The point at which playback starts is automatically stored in the memory as the cue point . The pickup then
returns to the cue point when the CUE button is pressed. (Back Cue)
Figure 4-1
5. Stopping Playback
There are two ways to stop playback.
1. Press the PLAY/PAUSE button during playback to pause at that point.
2. Press the CUE button during playback to return to the cue point and enter pause condition.(Back Cue)
CUE
Figure 5
8
6. Pausing
Press the PLAY/PAUSE button to switch between play and pause.
The play indicator flashes when the pause mode is set.
Figure 6 show the relationship between the play and pause.
6
4
2
3
7
5
1
1
2
3
4
The player has completed the cue or pause operation
and is waiting for the play start command.
When the PLAY/PAUSE button is pressed and enter
play mode is entered.
Playing.
The pause mode is set when the PLAY/PAUSE button
is pressed again.
5
6
7
Figure 6
Pausing.
Playback resumes when the PLAY/PAUSE button
is pressed again.
Playing.
7. Cueing
"Cueing" is the action of preparing for playback.
Press CUE button, the player will enter cue mode, the playback returns to cue point and enter pause condition,
the cue indicator lights up and the play indicator flashes. When PLAY/PAUSE button is pressed, play starts
from the cue point.
When the track search operation is completed after pressing the SKIP buttons, the player automatically finds
the position at which the sound starts and cues there(Auto Cue).
If the CUE button is pressed after the search operation or the scanning operation, the playback returns to cue
point and enters pause condition.
Figure 7-1 shows the relationship between the play and back cue operations.
2
8
3
1
1
2
3
4
9
6
4
2
8
3
7
5
1
The player has completed the cue or pause operation
and is waiting for the play start command.
When the PLAY/PAUSE button is pressed, playback
starts and the cue point is stored in the memory.
Playing.
The pause mode is set when the PLAY/PAUSE button
9
5
6
7
8
9
Figure 7-1
is Pressed again.
Pausing.
When the PLAY/PAUSE button is pressed again;
Playing.
Press the CUE button.
The pickup returns to the cue point.(Back Cue)
Cue point setting:
When play starts from pause by pressing the IN button or Scanning or Frame Search; also skip to a new track
by using skip button, the begin play point will be set to the new cue point.
When a new cue point is set, the cue indicator lights by flash for about 1 second.
NOTE: During cue mode, if the CUE button is pressed and hold, playback will start from the cue point, when the
button is released, the player will return to the cue mode automatically, it allows you to check the cue point.
8. Jog Wheel - The jog wheel serves two functions depending on the current operating mode:
The jog wheel will act as a slow frame search control when the unit is in pause or cue mode allowing you to set
a specific cue point or find a particular starting point.
The wheel also works as a momentary pitch bend during playback . Turning the wheel clockwise will
increase the pitch percentage up to +16%, and turning the wheel in the counterclockwise direction will
decrease the pitch percentage up to -16%. The pitch bend will be determined by how fast you turn the wheel.
9
9. Scanning (Fast forward/Fast backward)
Scanning is a function for moving quickly forward or backward when the
or
button is pressed.
The scanning speed depends on how long you hold the button.
Press and hold the
or
to begin scanning. The disc moves rapidly forward or backward and the sound is
output. The current scan point is indicated on the LCD.
Press and hold the
to scan in the forward scanning,
to scan in the reverse scanning.
10. Time display
MP3 MODE
Press the TIME button to select time display MP3 mode:
1 Elapsed time of a track.
2 Remaining time of a track.
ELAPSED
REMAIN
Figure 10-1
CD MODE
Press this button to switch the time display
It switches between the elapsed time and remaining time and total remaining time of the disc.
ELAPSED
TOTAL
REMAIN
REMAIN
Figure 10-2
11. Matching the Beats Per Minute (BPM)
There are two tools available for matching the BPM of the two CDs:
1
Use the pitch slider to adjust the BPM statically.
2
Use the PITCH BEND buttons to change the BPM temporarily.
Use the JOG WHEEL to change the BPM temporarily.
1)Pitch Slider
1
To adjust the BPM by sliding the pitch slider up or down, press the PITCH button to turn on the PITCH
adjustment function before use.
2
Slide the pitch slider up to decrease BPM, or down to increase BPM. The adjustment range is +/-4%,+/-8%
+/-16%
2)Pitch Bending
The BPM increases or decreases respectively while the PITCH BEND+ or PITCH BEND- button is pressed.
The BPM increase depends on how long you hold the button. If you hold the button for about 1/2 second,
the BPM wil l go either to +16% for PITCH BEND+ or -16% for PITCH BEND-. If you tap the button, the
BPM will only change a little so you can change the beat slightly without audible changes in the music.
The CD will return to the tempo indicated by the Pitch slider when you let go of the PITCH BEND+ or -.
Figure 11-1 shows an example of how to use the pitch bend function . In this example , both players are
playing and the
BPM has already been matched with the pitch sliders.
The bass beats also match
CD1
bass beat
bass beat
PITCH BEND
CD2
bass beat
bass beat
10
12. Fader start
You have the possibility to start the respective CD player directly from the mixer. Make sure that the Control
socket is connected with the respective socket on the mixer. Additionally, the Audio out sockets have to be
connected with the Line input sockets of your mixer. Please note that the Fader start function only works
with the appropriate mixers. Insert the CD and select the desired track. Start playback from your mixer.
13. Relay
In the Relay operation, the device automatically switches to the other player after every track. In this way,
you have the possibility to enlarge the music program by using several CDs.
To start, press the Relay button. Press the Single button (the display shows “ SINGLE” ) on both CD players.
Start playback of CD1. As soon as the current track of CD1 is finished, the player automatically starts CD2.
The first CD player goes into Pause-mode. Press the single button again for continuous mode (the “SINGLE”
display is not lit). When playback of all tracks of CD1 is finished, the player automatically starts CD2 and Cd1
is goes into pause-mode.
You can load a new CD or memorize a Cue point for either player in the Pause Mode.
When playback of all tracks or the current track of CD2 is finished, the player automatically starts CD1 and
CD2 goes into pause-mode.
CAUTION: The Relay operation does not work properly if the two CD players are connected to different power
amplifiers.
11
BEFORE SWITCHING OFF THE POWER
When you have finished using the CD player, before switching off the power, be sure that the disc holder had been
closed with the OPEN/CLOSE button.
CAUTION:
Do not forcibly close the disc holder when the power is off.
PWER OFF
PWER OFF
Do not switch off the power when the disc holder is open.
Switch off the power after the disc holder has been
closed with the OPEN/CLOSE button.
COMPACT DISCS
1. Precautions on handling compact discs
Do not allow fingerprints, oil or dust to get on the
surface of the disc.
If the disc is dirty, wipe it off with a soft dry cloth.
Do not use benzene, thinner, water, record spray,
electrostatic-proof chemicals, or silicone-treated
cloths to clean discs.
Always handle discs carefully to prevent damaging
the surface; in particular when removing a disc from
its case or returning it.
Do not bend the disc.
Do not apply heat.
Do not enlarge the hole in the center of the disc.
Do not write on the label (printed side) with a hardtipped implement such as a pencil or ball point pen.
Condensation will form if a disc is brought into a
warm
area from a colder one, such as outdoors in winter.
Do not attempt to dry the disc with a hair dryer, etc.
2. Precaution on storage
After playing a disc, always unload it from the player.
Always store the disc in the jewel case protect from
dirt or damage.
Do not place discs in the following areas:
1 Areas exposed to directs sunlight for a considerable
time.
2 Areas subject to accumulation of dust or high
humidity.
3 Areas affected by heat from indoor heaters, etc.
SPECIFIC ATIONS
GENERAL
Dimensions:
Main unit:
Control unit:
Weight:
Power supply:
Power consumption:
482(W) x 88.8(H) x 251(D) mm
19” (W) x 3 1/2” (H) x 9 4/5” (D)
482(W) x 88.8(H) x 60(D) mm
19” (W) x 3 1/2” (H) x 2 1/3(D)
5.3 kgs / 11.7 lbs
1.8 kgs / 3.9 lbs
Player unit:
Control unit:
Dual Voltage:
AC 115/230V, 50/60Hz
Single Voltage:
AC 100V, 50/60Hz (For Japan)
AC 110V, 60Hz (For Taiwan)
AC 120V, 60Hz (For U.S.A.,Canada,Mexico)
AC 220V, 50Hz (For United Arab Emirates,Chile,Aegentina)
AC 220V, 60Hz (For Philippines)
AC 230V, 50Hz (For Europe,New Zealand,South Africa,Singapore,Israel)
AC 240V, 50Hz (For Australia,U.K)
25W
12
WARRANTY & RETURN POLICY
WARRANTY & RETURN POLICY
Warranty
Through Stantons authorized dealers around the World, Stanton, or one of Stantons authorized distributors outside the U.S., will, without charge, repair
or replace, at the sole discretion of the entity responsible for making the repair or providing the replacement, any Stanton merchandise proved defective
in material or workmanship for a period of one (1) year following the date of original purchase. Exceptions to this warranty are as noted below:
The warranty for mechanical parts which are subject to wear and tear are limited to the earlier of either thirty (30) days following the date of original
purchase or the following number of cycles: Faders - 15,000; Rotary potentiometers - 10,000; and Switches - 10,000.
Stanton will warrant all replacement parts and repairs for ninety (90) days from the date of original shipment. Repairs made necessary by reason of mi use, alteration, normal wear, or accident are not covered under this warranty.
Returns
Authorized Stanton dealers are only authorized to sell and distribute merchandise within a specific country. All goods requiring warranty repair or replacement must be returned (freight prepaid if not hand-delivered) to the authorized Stanton dealer from whom the merchandise was purchased and in the
same country where the merchandise was purchased. For purposes of purchases made via the Internet, the merchandise must be returned to the authorized Stanton dealer in the country where the authorized Stanton dealer which sold the merchandise to purchaser is located and not the authorized Stanton
dealer in the country where the purchaser is located or the country in which the merchandise was received. Any returns to a non-authorized dealer or to
an authorized Stanton dealer not in the same country as the merchandise was intended to be sold or as set forth above will void this warranty.
To initiate a warranty repair, you must contact the authorized Stanton dealer from whom you purchased the merchandise, and follow such authorized
Stanton dealers return policy.
Stanton assumes no risk and shall be subject to no liability for damage or loss resulting from the specific use or application made of the merchandise.
Stantons liability for any claim, whether based on breach of contract, negligence, infringement of any rights of any party, or product liability, and relating
to the merchandise shall not exceed the price received by Stanton from our purchase of such merchandise. In no event will Stanton be liable for any
special, incidental or consequential damages (including loss of use, loss of profit and claims of third parties) however caused, whether by the negligence
of Stanton or otherwise. To the extent permitted by law and except as otherwise provided above, Stanton disclaims any express or implied warranties of
merchantability or fitness for a particular purpose.
The above warranty provides you with specific legal rights. You may also have additional rights, which are subject to variation from state to state and
country to country.
If there is a dispute regarding the warranty of merchandise that does not fall under the warranty conditions stated above, please include a written explanation with the merchandise when returned pursuant to the terms and conditions set forth herein.
Please register your product online at www.stantondj.com.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement