Stanton S-500 CD Player User Manual

Stanton S-500 CD Player User Manual
USER MANUAL
IMPORTANT TO SAFETY
IMPORTANT TO SAFETY
NOTE:
This CD player uses the semiconductor laser. To allow
you to enjoy music at a stable operation, it is
recommended to use this in a room of 5℃ 41℉ - 35℃
95℉.
WARNING:
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT
EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
CAUTION:
1. Handle the power supply cord carefully
Do not damage or deform the power supply cord. If it is
damaged or deformed, it may cause electric shock or
malfunction when used. When removing from wall
outlet, be sure to remove by holding the plug
attachment and not by pulling the cord.
RATING LABE
2. In order to prevent electric shock, do not open the
top cover. If a problem occurs, contact your dealer.
CLASS 1 LABEL
3. Do not place metal objects or spill liquid inside the
CD player. Electric shock or malfunction may result.
Please, record and retain the Model name and serial
number of your set shown on the rating label.
Model No. ___________ Serial No. ___________
CAUTION:
USE OF CONTROLS OR ADJUSTMENTS OR
REFORMANCE OF PROCEDURES OTHER THAN
THOSE SPECIFIED HEREIN MAY RESULT IN
HAZARDOUS RADIATION EXPOSURE.
CAUTION: TO REDUCE THE
RISK OF ELECTRIC SHOCK,
DO NOT REMOVE THE COVER
(OR BACK) . THERE ARE NO
SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
THE COMPACT DISC PLAYER SHOULD NOT BE
ADJUSTED OR REPAIRED BY ANYONE EXCEPT
PROPERLY QUALIFIED SERVICE PERSONNEL.
DOUBLE INSULATED - WHEN SERVICING, USE ONLY
IDENTICAL REPLACEMENT PARTS.
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to
alert the user to the presence of uninsulated
"dangerous voltage" within the product's
enclosure that may be of sufficient
magnitude to constitute a risk of electric
shock to persons.
NOTE:
This unit may cause interference to radio and television
reception.
• Line Voltage Selection (for multiple voltage
model only)
 The desired voltage may be set with the
VOLTAGE SELECTOR switch on the rear
panel, using a screwdriver.
 Do not twist the VOLTAGE SELECTOR
switch with excessive force as this may
cause damage.
 If the VOLTAGE SELECTOR switch does not move
smoothly, please contact a qualified serviceman.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
•FOR U.S.A. & CANADA MODEL ONLY
CAUTION
TO PREVENT ELECTRIC SHOCK DO NOT USE THIS
(POLARIZED) PLUG WITH AN EXTENSION CORD,
RECEPTACLE OR OTHER OUTLET UNLESS THE
BLADES CAN BE FULLY INSERTED TO PREVENT
BLADE EXPOSURE.
2
SAFETY INSTRUCTIONS
1. Read Instructions - All the safety and operating
plugs, convenience receptacles, and the point where
they exit from the appliance.
instructions should be read before the appliance is
13. Cleaning - The appliance should be cleaned only as
operated.
2. Retain
Instructions - The
recommended by the manufacturer.
safety and operating
Clean by wiping with a cloth slightly damp with water.
instructions should be retained for future reference.
Avoid getting water inside the appliance.
3. Heed Warnings-All warnings on the appliance and in
14. Disconnect power cord before servicing.
the operating instructions should be adhered to.
4. Follow Instructions-All operating and use instructions
15. Replace critical components
should be followed.
only with factory parts
or recommended equivalents.
5. Water and Moisture-The appliance should not be
16. For AC line powered units - Before returning repaired
used near water - for example, near a bathtub,
unit to user, use an ohm-meter to measure from both
washbowl, kitchen sink, laundry tub, in a wet
AC plug blades to all exposed metallic parts. The
basement, or near a swimming pool, and the like.
resistance should be more than 100,000 ohms.
6. Carts and Stands-The appliance should be used only
17. Non-use Periods-The power cord of the appliance
with a cart or stand that is recommended by the
should be unplugged from the outlet when left unused
manufacturer.
for a long period of time.
6A. An appliance and cart combination
18. Object and Liquid Entry-Care should be taken so that
should be moved with care. Quick
objects do not fall and liquids are not spilled into the
stops, excessive force, and uneven
enclosure through openings.
surfaces may cause the appliance and
19. Damage Requiring Service-The appliance should be
cart combination to overturn.
serviced by qualified service personnel when:
7. Wall or Ceiling Mounting-The appliance should be
A. The power-supply cord or the plug has been
mounted to a wall or ceiling only as recommended by
damaged; or
the manufacturer.
B. Objects have fallen, or liquid has been spilled into
8. Ventilation-The appliance should be situated so that
the appliance; or
its location or position does not interfere with its proper
C. The appliance has been exposed to rain; or
ventilation. For example, the appliance should not be
D. The appliance does not appear to operate normally
situated on a bed, sofa, rug, or similar surface that
or exhibits a marked change in performance; or
may block the ventilation openings; or, placed in a
E. The appliance has been dropped, or the enclosure
built-in installation, such as a bookcase or cabinet that
damaged.
may impede the flow of air through the ventilation
20. Servicing-The user should not attempt any service to
openings.
the appliance beyond that described in the operating
9. Heat-The appliance should be situated away from
instructions. All other servicing should be referred to
heat sources such as radiators, heat registers, stoves,
qualified service personnel.
or other appliances (including amplifiers) that produce
21 Ventilation – The appliance should be situated so that
heat.
ist location or position does not interfere with its proper
10. Power Sources-The appliance should be connected
ventilation. For example, the appliance should not be
to a power supply only of the type described in the
siruated on a bed, sofa, rug, or similar surface that
operating instructions or as marked on the appliance.
may block the ventilation openings; or, placed in a
11. Grounding or Polarization - Precautions should be
built-in installation, such as a bookcase or cabinet that
taken so that the grounding or polarization means of
may impede the flow of air through the ventilation
an appliance is not defeated.
openings.
12. Power-Cord Protection- Power-supply cords should
22 Cleaning – The appliance should be cleaned only as
be routed so that they are not likely to be walked on or
recommended by the manufacturer.
pinched by items placed upon or against them, paying
23 Nonuse Periods – The power cord of the appliance
particular attention to the cord in correspondence of
should be unplugged from the outlet when left unused
for a long period of time.
3
NOTE ON USE
•
•
•
•
•
•
•
•
Allow for sufficient heat dispersion when installed on a rack.
Handle the power cord carefully.
Hold the plug when unplugging the cord.
Keep the set free from moisture, water, and dust.
Unplug the power cord when not using the set for long periods of time.
Do not obstruct the ventilation holes. (For sets with ventilation holes.)
Do not let foreign objects in the set.
Do not let insecticides, benzene, and thinner come in contact with the set.
Never disassemble or modify the set in any way.
For 220 volt use in USA, USA nema style 220 volt plug. For other countries, use proper plug for the local outlet.
MAIN FEATURES
(1)
(2)
(3)
(4)
(5)
(6)
8 times oversampling 1 bit D/A converter.
3 different speed scan.
Frame search.
Auto cue.
20 tracks program play.
Pitch display.
MAIN UNIT
2
3
1
2
6
4
5
4
(1)POWER
(2) Disc Holder
(3) OP/CL
(4) REMOTE CONTROL CONNECTOR
(5) AUDIO OUT
(6) DIGITAL OUT SOCKET
4
5
MAIN FEATURES
CONTROL UNIT
1 16 4 9
3 12 10 2
1314 15 11
5
6
7
8 18 1 16 4 9
17
1314 15 11
3 12 10 2
5
CONNECT
TO
MAIN UNIT
CONNECT
TO
MAIN UNIT
2
1
CONTROL
6
17
CONTROL
2
19
7
8
1
19
20
20
(11)CUE (Cue Button)
(12)PROG.
(13)B.SKIP
(14)SEARCH/SCAN
(15)SEARCH/SCAN
(16)F.SKIP
(17)PITCH (Pitch Indicator)
(18)REALY
(19)CONTROL CONNECTOR
(20)CONTROL SOCKETS
(1) OP/CL
(2) TIME (Time Button)
(3) LCD (Liquid Crystal Display)
(4) LOOP (Loop button)
(5) PITCH - (Pitch Bend - Button)
(6) PITCH +(Pitch Bend + Button)
(7) PITCH (Pitch Button)
(8) Pitch Slider
(9) PLAY/PAUSE
/ (Play/Pause Button)
(10)SGL/CTN (Single/Continuous Button)
LCD
TRACK
21
M
22
S
(21) ~(24)TRACK, MINUTE,
FRAME Displays
(25) BAR Indicator
(26) ELAPSED Indicator
(27) CONTINU Indicator
(28) SINGLE Indicator
(29) REMAIN Indicator
(30) PITCH DISPLAY
F
23 24 25 26 27 28 29 30
5
SECOND
and
PREPARATIONS
1. Checking the Contents
Check that the carton contains the following items:
1) Main unit
2) Control unit
3) Operating instructions (this booklet)
4) Pair of RCA pin cord.
5) Control cords (1 meter)
2. Installing the Unit
Mount the unit onto your console or rack with 19" EIA rack rails.
CAUTION:
l The player will work normally when the main unit is
mounted with the front panel at within 15 degrees of the
vertical plane. If the unit is tilted excessively, discs may
not be loaded or unloaded properly.
(Figure 1)
l The control panel's LCDs are designed to be
clearly visible within the angles shown in Figure 2.
Mount the control unit so that the visual angle is within
this range.
Max.
15°
45°
5°
Control
panel Button
Main unit
.
Figure 1
Figure 2
Connections
1) Turn off the POWER switch.
2) Connect the RCA pin cord to the input on your mixer.
3) Connect the control cords to the REMOTE connector on the main unit.
CAUTION:
• Be sure to use the supplied control cords. Using another type of cable may result in damage.
• Be sure the power is off when connecting the control cords. Otherwise the units may not work properly.
6
NAMES AND FUNCTIONS
Main Unit Front Panel
(1) POWER (Power ON/OFF Switch)
When the POWER switch is pressed, the power turns
on.
(2) Disc Holder
Place the discs in the holder. Press the OPEN/CLOSE
button to open and close the disc holder.
(3) OP/CL
Press it to open and close the disc holder. The control
unit also includes OP/CL button. The disc holder
cannot be opened during playback, so stop playback
before pressing the button.
(4) REMOTE CONTROL CONNECTOR
Connect this connector to the control unit using the
included control cord.
(5) AUDIO OUT
The audio signals from each player are output from
these jacks.
(6) DIGITAL OUT SOCKET
The music-signal of this socket is digital. Connect the
output to the respective input of a digital amplifier for
example.
CONTROL UNIT
(1) OP/CL
Press it to open and close the disc holder. The main
unit also includes OP/CL buttons. The disc holder
cannot be opened during playback, so stop playback
before pressing the button.
(2) TIME (Time Button)
Press this button to switch the time display between
the elapsed time and remaining time and total remain
time.
The selected mode is indicated by the ELAPSED and
REMAIN and TOTAL REMAIN indicator on the LCD.
(3) LCD
(4) LOOP (Loop Button)
Press the LOOP button to set the loop start point,
press the LOOP button again to set the loop end point.
(5) PITCH - Button
The CD slows down while this button is pressed.
Release the button to return to the original BPM.
(6) PITCH + Button
The CD speeds up while this button is pressed.
Release the button to return to the original BPM.
(7) PITCH (Pitch Button)
Use these button to enable or disable BPM adjustment
with the pitch sliders. BPM adjustment with the pitch
sliders is enabled when the PITCH LED lights.
(8) Pitch Slider
Use the slider to adjust the CD pitch. Slide up to
decrease the pitch, down to increase the pitch.
(9) PLAY/PAUSE Button
Use the button to start playback. Press once to start
playback, once again to set the pause mode, and once
more to resume playback.
(10) SGL/CTN (Single/Continuous Button)
Press it to switch between the single and continuous
play modes. The SINGLE mode is indicated by the
SINGLE indicator on the LCD.
(11) CUE (Cue Button)
Press the CUE button during playback to return to the
position at which playback started.
(12) PROG.
Press the PROGRAM button, the player will enter the
program mode and stop the CD playback.
(13) B. SKIP
Use these button to go back to the beginning of the
current track or select a previous track for playing.
(14) ,(15)SEARCH/SCAN
Press these buttons to perform frame search function
during pause mode or to perform scan function during
play mode.
(16) F. SKIP
Use these button to skip to the next CD track.
(17) PITCH (Pitch Indicator)
Moving the pitch slider will change the pitch only when
the pitch LED is illuminated.
(18) REALY
By pressing the RELAY button, the playback
automatically switches to the other player after every
track.
(19) Control connector
Connect this connector to the REMOTE connector on
the main unit using the included control cord.
(20) Control socket
Via the Control socket, the respective CD-player can be
remotely controlled. If you are using a mixer with fader
start-function connect the player with the Control Outsocket. Please note that these sockets must never be
connected with any voltage.
LCD
(21) ~(24)TRACK, MINUTE, SECOND and FRAME
Displays
These displays indicate information for the CD’s current
position and time.
(25) BAR Indicator
These ten indicators provide a visual display of the
approximate position of the pickup within the current
track.
(26) ELAPSED Indicator
It indicates that the time shown for the display is the
elapsed time.
(27) CONTINU Indicator
When the indicator lights, the function will cause the
unit to play continuously.
(28) SINGLE Indicator
When the indicator lights, playback will stop at the
beginning of the next track.
(29) REMAIN Indicator
It indicates that the time shown on the display is the
remaining time of playing track.
(30) PITCH DISPLAY
It shows the BPM change range, the BPM changes
within a range of +/-12%.
7
OPERATIONS
1. Opening and Closing the Disc Holder
l
l
Turn the unit power on. Press the OPEN/CLOSE button to open the disc holder. OPEN/CLOSE buttons are provided
on both the main unit and control unit.
The disc holder cannot be opened during playback to prevent playback from being interrupted if the OPEN/CLOSE
button is pressed accidentally. Stop the playback first, then press the OPEN/CLOSE button.
2. Loading discs
l
Hold the disc by the edges and place it in the disc holder, then press the OPEN/CLOSE button again to close the disc
holder. The unit will show the total track number and the total playing time for about 2 seconds then enter the cue
condition, the cue point will be set to the music starting point of the first track automatically.
Figure 2-1
l
l
CAUTION:
Do not place any foreign objects in the disc holder, and do not place more than one disc in the disc holder at a time.
Do not push the disc holder in manually when the power is off, as this may result in malfunction and damage the
player.
3. Selecting Tracks
l
l
l
l
Press the SKIP button once to move to one higher or lower track.
Hold the SKIP button to change tracks continuously at a higher speed.
When a new track is selected during playback, playback begins as soon as the skip search operation is completed.
button is pressed while at the last track, the first track is selected. In the same way, if the skip
If the skip
button is pressed while at the first track, the last track is selected.
4. Starting Playback
l
l
Press the PLAY/PAUSE button during the pause or cue condition to start playback, the PLAY indicator lights.
The point at which playback starts is automatically stored in the memory as the cue point. The pickup then returns to
the cue point when the CUE button is pressed .(Back Cue)
Figure 4-1
5. Stopping Playback
l
There are two ways to stop playback.
1). Press the PLAY/PAUSE button during playback to pause at that point.
2). Press the CUE button during playback to return to the cue point and enter pause condition.(Back Cue)
CUE
Figure 5-1
8
OPERATIONS
6. Pausing
l
l
l
Press the PLAY/PAUSE button to switch between the play and pause.
The pause indicator lights when the pause mode is set.
Figure 6-1 show the relationship between the play and pause.
2
4
6
3
7
1
5
Figure 6-1
ŒThe player has completed the cue or pause operation and is waiting for the play start command.
•When the PLAY/PAUSE button is pressed, playback starts and the cue point is stored in the memory.
ŽPlaying.
•The pause mode is set when the PLAY/PAUSE button is pressed again
•Pausing.
‘Playback resumes when the PLAY/PAUSE button is pressed again.
’Playing.
7. Cueing
l
l
l
l
l
"Cueing" is the action of preparing for playback.
Press CUE button, the player will enter cue mode, the playback returns to cue point and enter pause condition, the
cue and pause indicator light up. When PLAY/PAUSE button is pressed, play starts from the cue point.
When the track search operation is completed after pressing the SKIP buttons, the player automatically finds the
position at which the sound starts and cues there(Auto Cue).
If the CUE button is pressed after the search operation or the scanning operation, the playback return to cue point and
enter pause condition.
Figure 7-1 shows the relationship between the play and back cue operations.
2
8
2
3
1
9
4
6
8
3
1
7
5
9
Figure 7-1
ŒThe player has completed the cue or pause operation and is waiting for the play start command.
•When the PLAY/PAUSE button is pressed, playback starts and the cue point is stored in the memory.
ŽPlaying.
•The pause mode is set when the PLAY/PAUSE button is pressed again.
•Pausing.
‘When the PLAY/PAUSE button is pressed again, playback resumes and the new cue point is stored in the
memory.
’Playing.
“Press the CUE button.
”The pickup returns to the cue point.(Back Cue)
l
Cue point setting:
When play starts from pause or skip to a new track by using skip button, the begin play point will be set to the new cue
point.
When a new cue point is set, the cue indicator lights by flash for about 1 second.
NOTE: Daring cue mode, if the CUE button is pressed and hold, playback will start from the cue point, when the button is
released, the player will return to the cue mode automatically, it allows you to check the cue point.
9
OPERATIONS
8. Frame search
l
l
l
Frame search is a function for monitoring the sound at a certain section of the disc and manually changing the position.
Searching is used to set play start points with precision.
or
while in pause or cue mode to begin searching. The sound for one revolution of the disc is
Press the
output repeatedly. The point at which the sound starts is indicated on the LCD.
If the time display and the CUE point are the same, the CUE indicator lights.
9. Scanning (Fast forward/Fast backward)
l
l
l
l
or
button is pressed.
Scanning is a function for moving quickly forward or backward when the
This unit supports 3 different speed, the scanning speed depends on how long you hold the button. If you hold the
button for a about 3 seconds, the scanning speed will be changed, when you release the button, the scanning
or
speed return to normal speed.
or
to begin scanning. The disc moves rapidly forward or backward and the sound is
Press and hold the
output. The current scan point is indicated on the LCD.
to scan in the forward scanning,
to scan in the reverse scanning.
Press and hold the
10. Time display
Press TIME button to select time display mode:
ΠElapsed time of a track.
• Remaining time of a track.
ELAPSED
REMAIN
TIME
TIME
Figure 10-1
11. Matching the Beats Per Minute (BPM)
There are two tools available for matching the BPM of the two CDs:
• Use the pitch slider to adjust the BPM statically.
‚ Use the PITCH BEND buttons to change the BPM temporarily.
1) Pitch Slider
ΠTo adjust the BPM by sliding the pitch slider up or down, press the PITCH button to turn on the PITCH
adjustment function before use.
• Slide the pitch slider up to decrease BPM, or down to increase BPM. The adjustment range is +/-10%.
l
l
l
l
2) Pitch Bending
The BPM increases or decreases respectively while the PITCH BEND+ or PITCH BEND- button is pressed.
The BPM increase depends on how long you hold the button. If you hold the button for about 1/2 second, theBPM will
go either to +16% for PITCH BEND+ or -16% for PITCH BEND-. If you tap the button, the BPM will only change a little
so you can change the beat slightly without audible changes in the music.
The CD will return to the tempo indicated by the Pitch slider when you let go to the PITCH BEND+ or -.
Figure 11-1 shows an example of how to use the pitch bend function. In this example, both players are playing and the
BPM has already been matched with the pitch sliders.
The bass beats also match
CD1
bass beat
Bass beat
PITCH BEND
CD2
bass beat
Bass beat
Figure 11-1
10
OPERATIONS
12. Program play
ΠPress the PROGRAM button, the player will enter the program mode and the CD will stop rotating.
• Select the desired track by pressing the SKIP button, then press the PROGRAM button again. The selected
track will be added to the program sequence.
Ž Repeat step 2 operation. A maximum of 20 tracks can be programmed at one time.
• Press the PLAY/PAUSE button to start the program play from the first selection.
• Press the program button again during program play to stop play.
‘ Press and hold the program button more than 2 seconds to cancel the program mode and erase all the current
program contents.
13. Loop Play
Œ
•
Ž
Press the LOOP button to set the loop start point A, the LOOP indicator will flashes on the LCD.
Press the LOOP button again to set the loop end point B, after the B point is set, the playback will enter the loop play
from A to B repeatedly.
Press the LOOP button again, the loop play function is canceled, the LOOP indicator goes out.
14. Faderstart
With the S-500, you have the possibility to start the respective CD-player direcatly from the mixer. Make sure that the
Control socket is connected with the respective socket on the mixer. Additionally, the Audio out socket have to be
connected with the Line-input sockets of your mixer. Please note that the Faderstart function only works with the
appropriate mixers. Insert the CD and select the desired track. Start playback from your mixer.
15. Relay
In the Relay-operation, the device automatically switches to the other player after every track. In this way, you have the
possibility to enlarge the music program by using several CDs.
Possibility 1:
Connect the Control-sockets of the two CD-players with one another. The Relay-button must remain unpressed (LED off).
Press the Single-button (The display shows “SINGLE”) on both CD-player. Start playback of CD1. As soon as the
current track of CD1 is finished, the player automatically starts CD2. The first CD-player goes into Pause-mode. You
can enter a new CD or memorize a Cue-point at the respective player in the Pause-Mode.
CAUTION: The Relay-operation does not work properly if the two CD-players are connected to different power amplifiers.
Possibility 2:
Press the Relay-button (LED on).
In the Single-mode, the device automatically starts with the playback of the other CD-player of the other CD-player at
the end of the track.
During the Relay-operation, the Faderstart-function is disabled.
You can switch the Relay-operation off via the Relay-button (LED on) and the Faderstart-function will work again.
11
BEFORE SWITCHING OFF THE POWER
When you have finished using the CD player, before switching off the power, be sure that the disc holder had been closed
with the OPEN/CLOSE button.
CAUTION:
Do not forcibly close the disc holder when the power is off.
POWER OFF
POWER OFF
û
Do not switch off the power when the disc holder is open.
Switch off the power after the disc holder has been closed
with the OPEN/CLOSE button.
COMPACT DISCS
Ÿ
1. Precautions on handling compact discs
Ÿ Do not allow fingerprints, oil or dust to get on the
surface of the disc.
If the disc is dirty, wipe it off with a soft dry cloth.
Ÿ Do not use benzene, thinner, water, record spray,
electrostatic-proof chemicals, or silicone-treated cloths
to clean discs.
Ÿ Always handle discs carefully to prevent damaging
the surface; in particular when removing a disc from its
case or returning it.
Ÿ Do not bend the disc.
Ÿ Do not apply heat.
Ÿ Do not enlarge the hole in the center of the disc.
Ÿ Do not write on the label (printed side) with a hardtipped implement such as a pencil or ball point pen.
Condensation will form if a disc is brought into a warm
area from a colder one, such as outdoors in winter. Do
not attempt to dry the disc with a hair dryer, etc.
2. Precaution on storage
Ÿ After playing a disc, always unload it from the
player.
Ÿ Always store the disc in the jewel case protect from
dirt or damage.
Ÿ Do not place discs in the following areas:
• Areas exposed to directs sunlight for a considerable time.
‚ Areas subject to accumulation of dust or high
humidity.
ƒ Areas affected by heat from indoor heaters, etc.
SPECIFICATIONS
GENERAL
Dimensions:
Weight:
Main unit:
482(W) x 88.8(H) x 262(D) mm
Control unit:
482(W) x 88.8(H) x 80(D) mm
Player unit:
5 kgs
Control unit:
2 kgs
Power supply:
115 / 230V AC, 50 / 60Hz
Power consumption:
25W
502-S500-1082
12
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement