Film Capacitors Metallized Polypropylene Film Capacitors (MKP) Series/Type: B32671L ... B32672L

Film Capacitors Metallized Polypropylene Film Capacitors (MKP) Series/Type: B32671L ... B32672L
Film Capacitors
Metallized Polypropylene Film Capacitors (MKP)
Series/Type:
B32671L ... B32672L
Date:
December 2012
© EPCOS AG 2012. Reproduction, publication and dissemination of this publication, enclosures hereto and the
information contained therein without EPCOS' prior express consent is prohibited.
Metallized polypropylene film capacitors (MKP)
B32671L ... B32672L
High V AC, high temperature (wound)
Typical applications
Electronic ballasts (resonant circuits)
SMPS
High-frequency AC loads
Pulse circuits
Dimensional drawing
Climatic
Max. operating temperature: 125 °C
Climatic category (IEC 60068-1): 55/110/56
Construction
Dielectric: metallized polypropylene (PP)
Wound capacitor technology
Plastic case (UL 94 V-0)
Epoxy resin sealing
Dimensions in mm
Features
Very high AC voltages for all frequency
ranges
Very small dimensions
High peak voltage for short time periods
High peak current
High pulse withstand capability
RoHS-compatible
Halogen-free capacitors available on request
Lead spacing
±0.4
10
15
Terminals
Parallel wire leads, lead-free tinned
Special lead lengths available on request
Marking
Manufacturer's logo
lot number, series number
Rated capacitance (coded)
Capacitance tolerance (code letter)
Rated AC voltage
Date of manufacture (coded)
Delivery mode
Bulk (untaped)
Taped (Ammo pack or reel)
For notes on taping, refer to chapter "Taping and packing“.
Please read Cautions and warnings and
Important notes at the end of this document.
Page 2 of 30
Lead diameter Type
d1
0.6
B32671L
0.8
B32672L
B32671L ... B32672L
High V AC, high temperature (wound)
Overview of available types
Lead spacing 10 mm
15 mm
Type
B32671L
B32672L
Page
4
6
VRMS (V AC)
200 250 250 500 600 700 160 200 250 250 500 600 700 900
VR (V DC)
400 630 1000 1000 1600 2000 250 420 630 1000 1300 1600 2000 2000
CR (nF)
0.68
1.0
1.2
1.5
2.2
2.7
3.3
3.9
4.7
5.6
6.2
6.8
8.2
10
12
15
22
33
47
56
68
100
150
220
330
390
470
680
1000
Please read Cautions and warnings and
Important notes at the end of this document.
Page 3 of 30
B32671L
High V AC, high temperature (wound)
Ordering codes and packing units (lead spacing 10 mm)
VRMS
VR
CR
f ≤1 kHz
V AC
V DC nF
200
400
22
33
47
68
100
250
630
15
22
33
47
56
250
1000
4.7
6.8
10
15
22
500
1000
3.3
3.9
4.7
5.6
6.2
6.8
8.2
10
12
Max. dimensions
w×h×l
mm
4.0 × 9.0 × 13.0
4.0 × 9.0 × 13.0
5.0 × 11.0 × 13.0
5.0 × 11.0 × 13.0
6.0 × 12.0 × 13.0
4.0 × 9.0 × 13.0
5.0 × 11.0 × 13.0
5.0 × 11.0 × 13.0
6.0 × 12.0 × 13.0
6.0 × 12.0 × 13.0
4.0 × 9.0 × 13.0
4.0 × 9.0 × 13.0
5.0 × 11.0 × 13.0
5.0 × 11.0 × 13.0
6.0 × 12.0 × 13.0
4.0 × 9.0 × 13.0
4.0 × 9.0 × 13.0
4.0 × 9.0 × 13.0
5.0 × 11.0 × 13.0
5.0 × 11.0 × 13.0
5.0 × 11.0 × 13.0
6.0 × 12.0 × 13.0
6.0 × 12.0 × 13.0
6.0 × 12.0 × 13.0
Ordering code
(composition see
below)
B32671L4223+***
B32671L4333+***
B32671L4473+***
B32671L4683+***
B32671L4104+***
B32671L6153+***
B32671L6223+***
B32671L6333+***
B32671L6473+***
B32671L6563+***
B32671L9472+***
B32671L9682+***
B32671L9103+***
B32671L9153+***
B32671L9223+***
B32671L0332+***
B32671L0392+***
B32671L0472+***
B32671L0562+***
B32671L0622+***
B32671L0682+***
B32671L0822+***
B32671L0103+***
B32671L0123+***
Ammo
pack
pcs./MOQ
4000
4000
3320
3320
2720
4000
3320
3320
2720
2720
4000
4000
3320
3320
2720
4000
4000
4000
3320
3320
3320
3320
2720
2720
Reel
pcs./
MOQ
6800
6800
5200
5200
4400
6800
5200
5200
4400
4400
6800
6800
5200
5200
4400
6800
6800
6800
5200
5200
5200
5200
4400
4400
MOQ = Minimum Order Quantity, consisting of 4 packing units.
Further E series, intermediate capacitance values and closer tolerances on request.
Composition of ordering code
+ = Capacitance tolerance code:
K = ±10%
J = ±5%
Please read Cautions and warnings and
Important notes at the end of this document.
*** = Packaging code:
289 = Ammo pack
189 = Reel
000 = Untaped (lead length 6 1 mm)
Page 4 of 30
Untaped
pcs./
MOQ
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
B32671L
High V AC, high temperature (wound)
Ordering codes and packing units (lead spacing 10 mm)
VRMS
VR
CR
f ≤1 kHz
V AC
V DC nF
600
1600
1.2
1.5
2.2
2.7
3.3
3.9
4.7
700
2000
1.0
1.2
1.5
2.2
2.7
3.3
3.9
4.7
Max. dimensions
w×h×l
mm
4.0 × 9.0 × 13.0
4.0 × 9.0 × 13.0
5.0 × 11.0 × 13.0
5.0 × 11.0 × 13.0
6.0 × 12.0 × 13.0
6.0 × 12.0 × 13.0
6.0 × 12.0 × 13.0
4.0 × 9.0 × 13.0
4.0 × 9.0 × 13.0
4.0 × 9.0 × 13.0
5.0 × 11.0 × 13.0
5.0 × 11.0 × 13.0
5.0 × 11.0 × 13.0
6.0 × 12.0 × 13.0
6.0 × 12.0 × 13.0
Ordering code
(composition see
below)
B32671L1122+***
B32671L1152+***
B32671L1222+***
B32671L1272+***
B32671L1332+***
B32671L1392+***
B32671L1472+***
B32671L8102+***
B32671L8122+***
B32671L8152+***
B32671L8222+***
B32671L8272+***
B32671L8332+***
B32671L8392+***
B32671L8472+***
Ammo
pack
pcs./MOQ
4000
4000
3320
3320
2720
2720
2720
4000
4000
4000
3320
3320
3320
2720
2720
Reel
pcs./
MOQ
6800
6800
5200
5200
4400
4400
4400
6800
6800
6800
5200
5200
5200
4400
4400
MOQ = Minimum Order Quantity, consisting of 4 packing units.
Further E series, intermediate capacitance values and closer tolerances on request.
Composition of ordering code
+ = Capacitance tolerance code:
K = ±10%
J = ±5%
Please read Cautions and warnings and
Important notes at the end of this document.
*** = Packaging code:
289 = Ammo pack
189 = Reel
000 = Untaped (lead length 6 1 mm)
Page 5 of 30
Untaped
pcs./
MOQ
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
B32672L
High V AC, high temperature (wound)
Ordering codes and packing units (lead spacing 15 mm)
VRMS
f ≤1 kHz
V AC
160
200
250
250
VR
CR
V DC nF
250 150
220
330
470
680
1000
420
68
100
150
220
330
470
680
630
33
47
68
100
150
220
390
1000
10
15
22
33
47
68
100
150
Max. dimensions
w×h×l
mm
5.0 × 10.5 × 18.0
6.0 × 11.0 × 18.0
7.0 × 12.5 × 18.0
8.5 × 14.5 × 18.0
9.0 × 17.5 × 18.0
11.0 × 18.5 × 18.0
5.0 × 10.5 × 18.0
5.0 × 10.5 × 18.0
6.0 × 11.0 × 18.0
7.0 × 12.5 × 18.0
8.0 × 14.0 × 18.0
9.0 × 17.5 × 18.0
11.0 × 18.5 × 18.0
5.0 × 10.5 × 18.0
5.0 × 10.5 × 18.0
6.0 × 11.0 × 18.0
7.0 × 12.5 × 18.0
8.5 × 14.5 × 18.0
9.0 × 17.5 × 18.0
11.0 × 18.5 × 18.0
5.0 × 10.5 × 18.0
5.0 × 10.5 × 18.0
5.0 × 10.5 × 18.0
6.0 × 11.0 × 18.0
7.0 × 12.5 × 18.0
8.5 × 14.5 × 18.0
9.0 × 17.5 × 18.0
11.0 × 18.5 × 18.0
Ordering code
(composition see
below)
B32672L2154+***
B32672L2224+***
B32672L2334+***
B32672L2474+***
B32672L2684+***
B32672L2105+***
B32672L4683+***
B32672L4104+***
B32672L4154+***
B32672L4224+***
B32672L4334+***
B32672L4474+***
B32672L4684+***
B32672L6333+***
B32672L6473+***
B32672L6683+***
B32672L6104+***
B32672L6154+***
B32672L6224+***
B32672L6394J***
B32672L0103+***
B32672L0153+***
B32672L0223+***
B32672L0333+***
B32672L0473+***
B32672L0683+***
B32672L0104+***
B32672L0154J***
Ammo
pack
pcs./MOQ
4680
3840
3320
2720
2560
4680
4680
3840
3320
2920
2560
4680
4680
3840
3320
2720
2560
4680
4680
4680
3840
3320
2720
2560
Reel
pcs./
MOQ
5200
4400
3600
2800
2800
2200
5200
5200
4400
3600
3000
2800
2200
5200
5200
4400
3600
2800
2800
2200
5200
5200
5200
4400
3600
2800
2800
2200
MOQ = Minimum Order Quantity, consisting of 4 packing units.
Further E series, intermediate capacitance values and closer tolerances on request.
Composition of ordering code
+ = Capacitance tolerance code:
K = ±10%
J = ±5%
Please read Cautions and warnings and
Important notes at the end of this document.
*** = Packaging code:
289 = Ammo pack
189 = Reel
000 = Untaped (lead length 6 1 mm)
Page 6 of 30
Untaped
pcs./
MOQ
4000
4000
4000
2000
2000
1000
4000
4000
4000
4000
2000
2000
1000
4000
4000
4000
4000
2000
2000
1000
4000
4000
4000
4000
4000
2000
2000
1000
B32672L
High V AC, high temperature (wound)
Ordering codes and packing units (lead spacing 15 mm)
VRMS
f ≤1 kHz
V AC
500
600
700
VR
CR
V DC nF
1300
6.8
10
22
33
47
68
1600
6.2
6.8
8.2
10
12
15
22
33
47
2000
1.0
1.2
1.5
2.2
2.7
3.3
3.9
4.7
5.6
6.2
6.8
8.2
Max. dimensions
w×h×l
mm
5.0 × 10.5 × 18.0
5.0 × 10.5 × 18.0
7.0 × 12.5 × 18.0
8.5 × 14.5 × 18.0
9.0 × 17.5 × 18.0
11.0 × 18.5 × 18.0
5.0 × 10.5 × 18.0
5.0 × 10.5 × 18.0
6.0 × 11.0 × 18.0
6.0 × 11.0 × 18.0
6.0 × 12.0 × 18.0
7.0 × 12.5 × 18.0
8.5 × 14.5 × 18.0
9.0 × 17.5 × 18.0
11.0 × 18.5 × 18.0
5.0 × 10.5 × 18.0
5.0 × 10.5 × 18.0
5.0 × 10.5 × 18.0
5.0 × 10.5 × 18.0
5.0 × 10.5 × 18.0
5.0 × 10.5 × 18.0
5.0 × 10.5 × 18.0
5.0 × 10.5 × 18.0
6.0 × 11.0 × 18.0
6.0 × 11.0 × 18.0
6.0 × 11.0 × 18.0
6.0 × 12.0 × 18.0
Ordering code
(composition see
below)
B32672L7682+***
B32672L7103+***
B32672L7223+***
B32672L7333+***
B32672L7473+***
B32672L7683J***
B32672L1622+***
B32672L1682+***
B32672L1822+***
B32672L1103+***
B32672L1123+***
B32672L1153+***
B32672L1223+***
B32672L1333+***
B32672L1473J***
B32672L8102+***
B32672L8122+***
B32672L8152+***
B32672L8222+***
B32672L8272+***
B32672L8332+***
B32672L8392+***
B32672L8472+***
B32672L8562+***
B32672L8622+***
B32672L8682+***
B32672L8822+***
Ammo
pack
pcs./MOQ
4680
4680
3320
2720
2560
4680
4680
3840
3840
3840
3320
2720
2560
4680
4680
4680
4680
4680
4680
4680
4680
3840
3840
3840
3840
Reel
pcs./
MOQ
5200
5200
3600
2800
2800
2200
5200
5200
4400
4400
4400
3600
2800
2800
2200
5200
5200
5200
5200
5200
5200
5200
5200
4400
4400
4400
4400
MOQ = Minimum Order Quantity, consisting of 4 packing units.
Further E series, intermediate capacitance values and closer tolerances on request.
Composition of ordering code
+ = Capacitance tolerance code:
K = ±10%
J = ±5%
Please read Cautions and warnings and
Important notes at the end of this document.
*** = Packaging code:
289 = Ammo pack
189 = Reel
000 = Untaped (lead length 6 1 mm)
Page 7 of 30
Untaped
pcs./
MOQ
4000
4000
4000
2000
2000
1000
4000
4000
4000
4000
4000
4000
2000
2000
1000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
B32672L
High V AC, high temperature (wound)
Ordering codes and packing units (lead spacing 15 mm)
VRMS
f ≤1 kHz
V AC
700
900
VR
CR
Max. dimensions
w×h×l
V DC nF
mm
2000
10
7.0 × 12.5 × 18.0
12
8.5 × 14.5 × 18.0
15
8.5 × 14.5 × 18.0
22
9.0 × 17.5 × 18.0
33
11.0 × 18.5 × 18.0
2000
0.68 5.0 × 10.5 × 18.0
1.0
5.0 × 10.5 × 18.0
1.2
6.0 × 11.0 × 18.0
1.5
6.0 × 11.0 × 18.0
2.2
7.0 × 12.5 × 18.0
2.7
8.0 × 14.5 × 18.0
3.3
8.5 × 14.5 × 18.0
3.9
9.0 × 17.5 × 18.0
4.7
9.0 × 17.5 × 18.0
5.6 11.0 × 18.5 × 18.0
6.2 11.0 × 18.5 × 18.0
6.8 11.0 × 18.5 × 18.0
Ordering code
(composition see
below)
B32672L8103+***
B32672L8123+***
B32672L8153+***
B32672L8223+***
B32672L8333J***
B32672L9681+***
B32672L9102+***
B32672L9122J***
B32672L9152+***
B32672L9222+***
B32672L9272J***
B32672L9332+***
B32672L9392J***
B32672L9472+***
B32672L9562+***
B32672L9622J***
B32672L9682K***
Ammo
pack
pcs./MOQ
3320
2720
2720
2560
4680
4680
3840
3840
3320
2920
2720
2560
2560
Reel
pcs./
MOQ
3600
2800
2800
2800
2200
5200
5200
4400
4400
3600
3000
2800
2800
2800
2200
2200
2200
MOQ = Minimum Order Quantity, consisting of 4 packing units.
Further E series, intermediate capacitance values and closer tolerances on request.
Composition of ordering code
+ = Capacitance tolerance code:
K = ±10%
J = ±5%
Please read Cautions and warnings and
Important notes at the end of this document.
*** = Packaging code:
289 = Ammo pack
189 = Reel
000 = Untaped (lead length 6 1 mm)
Page 8 of 30
Untaped
pcs./
MOQ
4000
2000
2000
2000
1000
4000
4000
4000
4000
4000
2000
2000
2000
2000
1000
1000
1000
B32671L ... B32672L
High V AC, high temperature (wound)
Technical data
Operating temperature range
Max. operating temperature Top,max
Upper category temperature Tmax
Lower category temperature Tmin
Rated temperature TR
Dissipation factor tan δ (in 10-3) at
at 20 °C
(upper limit values)
+125 °C
+110 °C
55 °C
+85 °C
≤27 nF 27 nF< CR ≤0.1 µF 0.1 µF < CR ≤1 µF >1 µF
0.8
1 kHz 0.8
10 kHz 1.0
1.0
100 kHz 2.0
3.0
> 100 GΩ (CR ≤ 0.33 µF)
< 30000 s (CR > 0.33 µF)
0.8
1.0
0.8
Insulation resistance Rins
at 20 °C, rel. humidity ≤ 65%
(minimum as-delivered values)
DC test voltage
1.6 VR, 2 s
TA (°C)
DC voltage derating
AC voltage derating
Category voltage VC
(continuous operation with VDC TA ≤ 85
VC = VR
VC,RMS = VRMS
or VAC at f ≤ 1 kHz)
85<TA≤110 VC = VR (165TA)/80
VC,RMS=VRMS (165TA)/80
TA (°C)
DC voltage (max. hours) AC voltage (max. hours)
Operating voltage Vop for
short operating periods
TA ≤ 100
Vop = 1.25 VC (2000 h)
Vop = 1.0 VC,RMS (2000 h)
(VDC or VAC at f ≤ 1 kHz)
100<TA≤125 Vop = 1.25 VC (1000 h)
Vop = 1.0 VC,RMS (1000 h)
Damp heat test
56 days/40 °C/93% relative humidity
Limit values after damp
Capacitance change ∆C/C
≤ 2%
heat test
Dissipation factor change ∆ tan δ
≤ 1.0 10-3 (at 1 kHz)
Insulation resistance Rins
≥ 50 GΩ
Reliability:
Failure rate λ
1 fit (≤ 1 10-9/h) at 0.5 VR, 40 °C
Service life tSL
200 000 h at 1.0 VR, 85 °C
For conversion to other operating conditions and temperatures,
refer to chapter "Quality, 2 Reliability".
Failure criteria:
Total failure
Short circuit or open circuit
Failure due to variation
Capacitance change ∆C/C
> 10%
of parameters
Dissipation factor tan δ
> 4 upper limit values
Insulation resistance Rins
< 1500 MΩ
Please read Cautions and warnings and
Important notes at the end of this document.
Page 9 of 30
B32671L ... B32672L
High V AC, high temperature (wound)
Pulse handling capability
"dV/dt" represents the maximum permissible voltage change per unit of time for non-sinusoidal
voltages, expressed in V/µs.
"k0" represents the maximum permissible pulse characteristic of the waveform applied to the
capacitor, expressed in V2/µs.
Note:
The values of dV/dt and k0 provided below must not be exceeded in order to avoid damaging the
capacitor.
dV/dt values
Lead spacing
Type
VRMS (V AC)
VR (V DC)
CR (nF)
1.0
1.2
1.5
2.2
2.7
3.3
3.9
4.7
5.6
6.2
6.8
8.2
10
12
15
22
33
47
56
68
100
10 mm
B32671L
200
250
400
630
dV/dt in V/µs
540
400
540
400
540
400
540
540
400
400
Please read Cautions and warnings and
Important notes at the end of this document.
1000
500
1000
810
810
810
810
810
Page 10 of 30
4700
4300
3800
3400
3200
3100
2700
2500
2300
600
1600
6000
5600
5200
5000
4700
4500
4000
700
2000
11000
10000
9500
9000
8600
8500
8200
8000
B32671L ... B32672L
High V AC, high temperature (wound)
dV/dt values
Lead spacing 15 mm
Type
B32672L
VRMS (V AC)
160
200
VR (V DC)
250
420
CR (nF)
dV/dt in V/µs
0.68
1.0
1.2
1.5
2.2
2.7
3.3
3.9
4.7
5.6
6.2
6.8
8.2
10
12
15
22
33
47
56
68
200
100
200
150
170
200
220
170
200
330
170
200
390
470
170
200
680
170
200
1000
170
Please read Cautions and warnings and
Important notes at the end of this document.
630
250
1000
500
1300
600
1600
700
2000
900
2000
300
300
300
300
300
300
300
445
445
445
445
445
445
445
445
1000
1000
1000
1000
1000
1000
3600
3500
3100
2800
2600
2300
2000
1700
1400
10000
9400
9000
7500
7100
6800
6000
5500
5000
4700
4500
4200
3900
3600
3300
2900
2300
15000
15000
14100
13500
11000
10600
10000
9000
8200
7500
7000
6700
Page 11 of 30
B32671L ... B32672L
High V AC, high temperature (wound)
k0 values
Lead spacing 10 mm
Type
B32671L
VRMS (V AC)
200
VR (V DC)
400
CR (nF)
k0 in V2/µs
1.0
1.2
1.5
2.2
2.7
3.3
3.9
4.7
5.6
6.2
6.8
8.2
10
12
15
22
150000
33
150000
47
150000
56
68
150000
100
150000
250
630
1000
200000
200000
200000
200000
200000
400000
400000
400000
400000
400000
Please read Cautions and warnings and
Important notes at the end of this document.
500
1000
9400000
8600000
8200000
7600000
6800000
6200000
5400000
5000000
4600000
Page 12 of 30
600
1600
14400000
14000000
13800000
13600000
13300000
13100000
12000000
700
2000
25000000
23000000
22500000
22000000
21500000
21000000
20900000
20800000
B32671L ... B32672L
High V AC, high temperature (wound)
k0 values
Lead spacing
Type
VRMS (V AC)
VR (V DC)
CR (nF)
0.68
1.0
1.2
1.5
2.2
2.7
3.3
3.9
4.7
5.6
6.2
6.8
8.2
10
12
15
22
33
47
56
68
100
150
220
330
390
470
680
1000
15 mm
B32672L
160
200
250
420
k0 in V2/µs
120000
120000
100000 120000
100000 120000
100000 120000
100000 120000
100000
100000
Please read Cautions and warnings and
Important notes at the end of this document.
250
630
1000
500000
500000
500000
500000
500000
500000
500000
1000000
1000000
1000000
1000000
1000000
1000000
1000000
1000000
500
1300
700
2000
900
2000
20300000
19600000
19200000
18600000
18200000
18000000
16800000
15800000
13100000
11520000 12700000
3000000 11200000 12300000
9920000 11800000
3000000 8960000 11100000
8320000 10600000
7360000 10400000
3000000 6400000 9300000
3000000 5440000 9000000
3000000 4480000
3000000
30000000
30000000
29400000
28000000
27500000
27300000
27000000
25200000
23500000
19500000
19000000
18400000
Page 13 of 30
600
1600
B32671L ... B32672L
High V AC, high temperature (wound)
Impedance Z versus frequency f
(typical values)
Please read Cautions and warnings and
Important notes at the end of this document.
Page 14 of 30
B32671L
High V AC, high temperature (wound)
Permissible AC voltage VRMS versus frequency f (for sinusoidal waveforms TA ≤ 100 °C)
For TA >100 °C, please refer to "General technical information", section 3.2.3.
Lead spacing 10 mm
400 V DC/200 V AC
630 V DC/250 V AC
1000 V DC/250 V AC
1000 V DC/500 V AC
Please read Cautions and warnings and
Important notes at the end of this document.
Page 15 of 30
B32671L
High V AC, high temperature (wound)
Permissible AC voltage VRMS versus frequency f (for sinusoidal waveforms TA ≤ 100 °C)
For TA >100 °C, please refer to "General technical information", section 3.2.3.
Lead spacing 10 mm
1600 V DC/600 V AC
Please read Cautions and warnings and
Important notes at the end of this document.
2000 V DC/700 V AC
Page 16 of 30
B32672L
High V AC, high temperature (wound)
Permissible AC voltage VRMS versus frequency f (for sinusoidal waveforms TA ≤100 °C)
For TA >100 °C, please refer to "General technical information", section 3.2.3.
Lead spacing 15 mm
250 V DC/160 V AC
420 V DC/200 V AC
630 V DC/250 V AC
1000 V DC/250 V AC
Please read Cautions and warnings and
Important notes at the end of this document.
Page 17 of 30
B32672L
High V AC, high temperature (wound)
Permissible AC voltage VRMS versus frequency f (for sinusoidal waveforms TA ≤100 °C)
For TA >100 °C, please refer to "General technical information", section 3.2.3.
Lead spacing 15 mm
1300 V DC/500 V AC
1600 V DC/600 V AC
2000 V DC/700 V AC
2000 V DC/900 V AC
Please read Cautions and warnings and
Important notes at the end of this document.
Page 18 of 30
B32671L ... B32672L
High V AC, high temperature (wound)
Operation at overvoltages during heating and ignition of lamps (TA ≤40 °C)
In lighting applications, the capacitors can be subjected to overvoltages during the heating and ignition periods. An overvoltage occurs when the operation voltage exceeds the permissible
AC voltage at the resonant frequency fr.
For a repetitive application of on/off switching pulses (as for example in the life tests applied by
electronic ballast manufacturers), limits have to be imposed on the time periods under overvoltage and on the duty cycle, in order to keep the capacitance value within the required margins:
The overvoltage time tOV should be less than 1 sec.
The maximum duty cycle of the overvoltage is given by
where VRMS,ov is the RMS voltage during period tOV
and VRMS is the permissible AC voltage for continuous operation at the resonant frequency fr
(given by the “permissible AC voltage versus frequency f” graphics in theprevious pages).
The drift of capacitance depends on the Vpp attained, and the total time under overvoltage,
which is calculated in hours as follows:
(Ni tOV) / 3600
where Ni is the number of overvoltage impulses and tOV is expressed in seconds.
The maximum drift of capacitance as a function of both parameters is provided graphically in the
following pages.
Please read Cautions and warnings and
Important notes at the end of this document.
Page 19 of 30
B32671L
High V AC, high temperature (wound)
Estimation of the maximum drift of capacitance value in function of the number of total
hours overvoltage
Lead spacing 10 mm
500 V AC/1000 V DC
Please read Cautions and warnings and
Important notes at the end of this document.
600 V AC/1600 V DC
Page 20 of 30
B32672L
High V AC, high temperature (wound)
Estimation of the maximum drift of capacitance value in function of the number of total
hours overvoltage
Lead spacing 15 mm
600 V AC/1600 V DC
Please read Cautions and warnings and
Important notes at the end of this document.
700 V AC/2000 V DC
Page 21 of 30
B32671L ... B32672L
High V AC, high temperature (wound)
Mounting guidelines
1
Soldering
1.1
Solderability of leads
The solderability of terminal leads is tested to IEC 60068-2-20, test Ta, method 1.
Before a solderability test is carried out, terminals are subjected to accelerated ageing (to
IEC 60068-2-2, test Ba: 4 h exposure to dry heat at 155 °C). Since the ageing temperature is far
higher than the upper category temperature of the capacitors, the terminal wires should be cut off
from the capacitor before the ageing procedure to prevent the solderability being impaired by the
products of any capacitor decomposition that might occur.
Solder bath temperature
235 ±5 °C
Soldering time
2.0 ±0.5 s
Immersion depth
2.0 +0/0.5 mm from capacitor body or seating plane
Evaluation criteria:
Visual inspection
Wetting of wire surface by new solder ≥90%, free-flowing solder
1.2
Resistance to soldering heat
Resistance to soldering heat is tested to IEC 60068-2-20, test Tb, method 1A.
Conditions:
Series
Solder bath temperature Soldering time
MKT boxed (except 2.5 × 6.5 × 7.2 mm) 260 ±5 °C
coated
uncoated (lead spacing > 10 mm)
MFP
MKP (lead spacing > 7.5 mm)
MKT boxed (case 2.5 × 6.5 × 7.2 mm)
MKP (lead spacing ≤ 7.5 mm)
MKT uncoated (lead spacing ≤ 10 mm)
insulated (B32559)
Please read Cautions and warnings and
Important notes at the end of this document.
Page 22 of 30
10 ±1 s
5 ±1 s
<4s
recommended soldering
profile for MKT uncoated
(lead spacing ≤ 10 mm) and
insulated (B32559)
B32671L ... B32672L
High V AC, high temperature (wound)
Immersion depth
2.0 +0/0.5 mm from capacitor body or seating plane
Shield
Heat-absorbing board, (1.5 ±0.5) mm thick, between capacitor
body and liquid solder
Evaluation criteria:
Visual inspection
∆C/C0
tan δ
Please read Cautions and warnings and
Important notes at the end of this document.
No visible damage
2% for MKT/MKP/MFP
5% for EMI suppression capacitors
As specified in sectional specification
Page 23 of 30
B32671L ... B32672L
High V AC, high temperature (wound)
1.3
General notes on soldering
Permissible heat exposure loads on film capacitors are primarily characterized by the upper category temperature Tmax. Long exposure to temperatures above this type-related temperature limit
can lead to changes in the plastic dielectric and thus change irreversibly a capacitor's electrical
characteristics. For short exposures (as in practical soldering processes) the heat load (and thus
the possible effects on a capacitor) will also depend on other factors like:
Pre-heating temperature and time
Forced cooling immediately after soldering
Terminal characteristics:
diameter, length, thermal resistance, special configurations (e.g. crimping)
Height of capacitor above solder bath
Shadowing by neighboring components
Additional heating due to heat dissipation by neighboring components
Use of solder-resist coatings
The overheating associated with some of these factors can usually be reduced by suitable countermeasures. For example, if a pre-heating step cannot be avoided, an additional or reinforced
cooling process may possibly have to be included.
EPCOS recommends the following conditions:
Pre-heating with a maximum temperature of 110 °C
Temperature inside the capacitor should not exceed the following limits:
MKP/MFP 110 °C
MKT 160 °C
When SMD components are used together with leaded ones, the leaded film capacitors should
not pass into the SMD adhesive curing oven. The leaded components should be assembled after the SMD curing step.
Leaded film capacitors are not suitable for reflow soldering.
Uncoated capacitors
For uncoated MKT capacitors with lead spacings ≤10 mm (B32560/B32561) the following measures are recommended:
pre-heating to not more than 110 °C in the preheater phase
rapid cooling after soldering
Please read Cautions and warnings and
Important notes at the end of this document.
Page 24 of 30
B32671L ... B32672L
High V AC, high temperature (wound)
Cautions and warnings
Do not exceed the upper category temperature (UCT).
Do not apply any mechanical stress to the capacitor terminals.
Avoid any compressive, tensile or flexural stress.
Do not move the capacitor after it has been soldered to the PC board.
Do not pick up the PC board by the soldered capacitor.
Do not place the capacitor on a PC board whose PTH hole spacing differs from the specified
lead spacing.
Do not exceed the specified time or temperature limits during soldering.
Avoid external energy inputs, such as fire or electricity.
Avoid overload of the capacitors.
The table below summarizes the safety instructions that must always be observed. A detailed description can be found in the relevant sections of the chapters "General technical information" and
"Mounting guidelines".
Topic
Storage conditions
Flammability
Resistance to
vibration
Safety information
Reference chapter
"General technical
information"
Make sure that capacitors are stored within the
4.5
specified range of time, temperature and humidity "Storage conditions"
conditions.
Avoid external energy, such as fire or electricity
5.3
(passive flammability), avoid overload of the
"Flammability"
capacitors (active flammability) and consider the
flammability of materials.
Do not exceed the tested ability to withstand
5.2
vibration. The capacitors are tested to
"Resistance to vibration"
IEC 60068-2-6.
EPCOS offers film capacitors specially designed
for operation under more severe vibration regimes
such as those found in automotive applications.
Consult our catalog "Film Capacitors for
Automotive Electronics".
Please read Cautions and warnings and
Important notes at the end of this document.
Page 25 of 30
B32671L ... B32672L
High V AC, high temperature (wound)
Topic
Safety information
Soldering
Do not exceed the specified time or temperature
limits during soldering.
Cleaning
Use only suitable solvents for cleaning capacitors.
Embedding of
When embedding finished circuit assemblies in
capacitors in
plastic resins, chemical and thermal influences
finished assemblies must be taken into account.
Caution: Consult us first, if you also wish to
embed other uncoated component types!
Please read Cautions and warnings and
Important notes at the end of this document.
Page 26 of 30
Reference chapter
"Mounting guidelines"
1 "Soldering"
2 "Cleaning"
3 "Embedding of
capacitors in finished
assemblies"
B32671L ... B32672L
High V AC, high temperature (wound)
Symbols and terms
Symbol
α
αC
A
βC
C
CR
∆C
∆C/C
∆C/CR
dt
∆t
∆T
∆tan δ
∆V
dV/dt
∆V/∆t
E
ESL
ESR
f
f1
f2
fr
FD
FT
i
IC
English
Heat transfer coefficient
Temperature coefficient of capacitance
Capacitor surface area
Humidity coefficient of capacitance
Capacitance
Rated capacitance
Absolute capacitance change
Relative capacitance change (relative
deviation of actual value)
Capacitance tolerance (relative deviation
from rated capacitance)
Time differential
Time interval
Absolute temperature change
(self-heating)
Absolute change of dissipation factor
Absolute voltage change
Time differential of voltage function (rate
of voltage rise)
Voltage change per time interval
Activation energy for diffusion
Self-inductance
Equivalent series resistance
Frequency
Frequency limit for reducing permissible
AC voltage due to thermal limits
German
Wärmeübergangszahl
Temperaturkoeffizient der Kapazität
Kondensatoroberfläche
Feuchtekoeffizient der Kapazität
Kapazität
Nennkapazität
Absolute Kapazitätsänderung
Relative Kapazitätsänderung (relative
Abweichung vom Ist-Wert)
Kapazitätstoleranz (relative Abweichung
vom Nennwert)
Differentielle Zeit
Zeitintervall
Absolute Temperaturänderung
(Selbsterwärmung)
Absolute Änderung des Verlustfaktors
Absolute Spannungsänderung
Differentielle Spannungsänderung
(Spannungsflankensteilheit)
Spannungsänderung pro Zeitintervall
Aktivierungsenergie zur Diffusion
Eigeninduktivität
Ersatz-Serienwiderstand
Frequenz
Grenzfrequenz für thermisch bedingte
Reduzierung der zulässigen
Wechselspannung
Frequency limit for reducing permissible Grenzfrequenz für strombedingte
AC voltage due to current limit
Reduzierung der zulässigen
Wechselspannung
Resonant frequency
Resonanzfrequenz
Thermal acceleration factor for diffusion Therm. Beschleunigungsfaktor zur
Diffusion
Derating factor
Deratingfaktor
Current (peak)
Stromspitze
Category current (max. continuous
Kategoriestrom (max. Dauerstrom)
current)
Please read Cautions and warnings and
Important notes at the end of this document.
Page 27 of 30
B32671L ... B32672L
High V AC, high temperature (wound)
Symbol
IRMS
iz
k0
LS
λ
λ0
λtest
Pdiss
Pgen
Q
ρ
R
R
Ri
Rins
RP
RS
S
t
T
τ
tan δ
tan δD
tan δP
tan δS
TA
Tmax
Tmin
tOL
Top
TR
Tref
tSL
VAC
English
(Sinusoidal) alternating current,
root-mean-square value
Capacitance drift
Pulse characteristic
Series inductance
Failure rate
Constant failure rate during useful
service life
Failure rate, determined by tests
Dissipated power
Generated power
Heat energy
Density of water vapor in air
Universal molar constant for gases
Ohmic resistance of discharge circuit
Internal resistance
Insulation resistance
Parallel resistance
Series resistance
severity (humidity test)
Time
Temperature
Time constant
Dissipation factor
Dielectric component of dissipation
factor
Parallel component of dissipation factor
Series component of dissipation factor
Ambient temperature
Upper category temperature
Lower category temperature
Operating life at operating temperature
and voltage
Operating temperature
Rated temperature
Reference temperature
Reference service life
AC voltage
Please read Cautions and warnings and
Important notes at the end of this document.
German
(Sinusförmiger) Wechselstrom
Inkonstanz der Kapazität
Impulskennwert
Serieninduktivität
Ausfallrate
Konstante Ausfallrate in der
Nutzungsphase
Experimentell ermittelte Ausfallrate
Abgegebene Verlustleistung
Erzeugte Verlustleistung
Wärmeenergie
Dichte von Wasserdampf in Luft
Allg. Molarkonstante für Gas
Ohmscher Widerstand des
Entladekreises
Innenwiderstand
Isolationswiderstand
Parallelwiderstand
Serienwiderstand
Schärfegrad (Feuchtetest)
Zeit
Temperatur
Zeitkonstante
Verlustfaktor
Dielektrischer Anteil des Verlustfaktors
Parallelanteil des Verlfustfaktors
Serienanteil des Verlustfaktors
Umgebungstemperatur
Obere Kategorietemperatur
Untere Kategorietemperatur
Betriebszeit bei Betriebstemperatur und
-spannung
Beriebstemperatur
Nenntemperatur
Referenztemperatur
Referenz-Lebensdauer
Wechselspannung
Page 28 of 30
B32671L ... B32672L
High V AC, high temperature (wound)
Symbol
VC
VC,RMS
English
Category voltage
Category AC voltage
VCD
Vch
VDC
VFB
Vi
Vo
Vop
Vp
Vpp
VR
Corona-discharge onset voltage
Charging voltage
DC voltage
Fly-back capacitor voltage
Input voltage
Output voltage
Operating voltage
Peak pulse voltage
Peak-to-peak voltage Impedance
Rated voltage
Amplitude of rated AC voltage
R
VRMS
German
Kategoriespannung
(Sinusförmige)
Kategorie-Wechselspannung
Teilentlade-Einsatzspannung
Ladespannung
Gleichspannung
Spannung (Flyback)
Eingangsspannung
Ausgangssspannung
Betriebsspannung
Impuls-Spitzenspannung
Spannungshub
Nennspannung
Amplitude der Nenn-Wechselspannung
VSC
Vsn
(Sinusoidal) alternating voltage,
root-mean-square value
S-correction voltage
Snubber capacitor voltage
Z
Impedance
Spannung bei Anwendung "S-correction"
Spannung bei Anwendung
"Beschaltung"
Scheinwiderstand
Lead spacing
Rastermaß
Please read Cautions and warnings and
Important notes at the end of this document.
(Sinusförmige) Wechselspannung
Page 29 of 30
Important notes
The following applies to all products named in this publication:
1. Some parts of this publication contain statements about the suitability of our products for
certain areas of application. These statements are based on our knowledge of typical requirements that are often placed on our products in the areas of application concerned. We
nevertheless expressly point out that such statements cannot be regarded as binding
statements about the suitability of our products for a particular customer application.
As a rule, EPCOS is either unfamiliar with individual customer applications or less familiar
with them than the customers themselves. For these reasons, it is always ultimately incumbent on the customer to check and decide whether an EPCOS product with the properties described in the product specification is suitable for use in a particular customer application.
2. We also point out that in individual cases, a malfunction of electronic components or
failure before the end of their usual service life cannot be completely ruled out in the
current state of the art, even if they are operated as specified. In customer applications
requiring a very high level of operational safety and especially in customer applications in
which the malfunction or failure of an electronic component could endanger human life or
health (e.g. in accident prevention or lifesaving systems), it must therefore be ensured by
means of suitable design of the customer application or other action taken by the customer
(e.g. installation of protective circuitry or redundancy) that no injury or damage is sustained by
third parties in the event of malfunction or failure of an electronic component.
3. The warnings, cautions and product-specific notes must be observed.
4. In order to satisfy certain technical requirements, some of the products described in this
publication may contain substances subject to restrictions in certain jurisdictions (e.g.
because they are classed as hazardous). Useful information on this will be found in our Material Data Sheets on the Internet (www.epcos.com/material). Should you have any more detailed questions, please contact our sales offices.
5. We constantly strive to improve our products. Consequently, the products described in this
publication may change from time to time. The same is true of the corresponding product
specifications. Please check therefore to what extent product descriptions and specifications
contained in this publication are still applicable before or when you place an order. We also
reserve the right to discontinue production and delivery of products. Consequently, we
cannot guarantee that all products named in this publication will always be available. The
aforementioned does not apply in the case of individual agreements deviating from the foregoing for customer-specific products.
6. Unless otherwise agreed in individual contracts, all orders are subject to the current version of the "General Terms of Delivery for Products and Services in the Electrical Industry" published by the German Electrical and Electronics Industry Association
(ZVEI).
7. The trade names EPCOS, BAOKE, Alu-X, CeraDiode, CeraLink, CSMP, CSSP, CTVS,
DeltaCap, DigiSiMic, DSSP, FilterCap, FormFit, MiniBlue, MiniCell, MKD, MKK, MLSC,
MotorCap, PCC, PhaseCap, PhaseCube, PhaseMod, PhiCap, SIFERRIT, SIFI, SIKOREL,
SilverCap, SIMDAD, SiMic, SIMID, SineFormer, SIOV, SIP5D, SIP5K, ThermoFuse,
WindCap are trademarks registered or pending in Europe and in other countries. Further
information will be found on the Internet at www.epcos.com/trademarks.
Page 30 of 30
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement