Advertisement
Advertisement
AV Control Receiver
Operating Instructions
Model No.
SA-DX1050
SA-DX950
SA-DX1050
E EB GN
Note:
“EB” on the packaging indicates the United Kingdom.
Before connecting, operating or adjusting this product, please read these instructions completely.
Please keep this manual for future reference.
RQT5802-B
Dear customer
Thank you for purchasing this product.
For optimum performance and safety, please read these instructions carefully.
These operating instructions are applicable to models SA-
DX1050 and SA-DX950, however, are intended primarily for model SA-DX1050.
Model SA-DX1050 is only for Europe.
2
RQT5802
Table of contents
Before use
Supplied accessories ................................................................
3
Safety precautions .....................................................................
3
Caution for AC Mains Lead .....................................................
4
Control reference guide ...........................................................
5
Connections
Connections ................................................................................
6
Connecting video equipment .........................................................6
Connecting audio equipment.........................................................7
Connecting digital equipment ........................................................7
Antenna connections .....................................................................8
Connecting the AC mains lead and other information ...................9
Speaker connections ..............................................................
10
Placement of speakers ................................................................10
Connecting speakers...................................................................10
Preparations
Customizing your receiver ....................................................
12
Basic steps ..................................................................................13
Adjusting speaker output level ............................................
15
Operations
DSP sound modes ...................................................................
16
STEREO mode............................................................................16
SURROUND mode......................................................................16
SFC modes..................................................................................17
Enjoying the sounds ...............................................................
18
Adjusting the tone and balance ...................................................20
Using the VCR 2 terminals ..........................................................20
Using headphones.......................................................................20
Muting the volume .......................................................................21
Adjusting the subwoofer level......................................................21
Using the TAPE MONITOR .........................................................21
Radio functions
The radio .....................................................................................
22
Manual tuning ..............................................................................22
Preset tuning ...............................................................................23
RDS broadcasts Only for Europe .......................................
24
To display RDS information.........................................................24
PTY search..................................................................................24
EON tuning ..................................................................................25
PTY displays................................................................................25
Reference
Making a recording ..................................................................
26
Timer function ...........................................................................
27
The HELP function ...................................................................
28
Maintenance ..............................................................................
28
Troubleshooting guide ...........................................................
29
Specifications ...........................................................................
30
Enjoying surround sound
Pages
Connect your equipment
6–9
Position and connect the speakers
10–11
Change the settings
12–13
Adjust speaker output level
15
Sit back and enjoy the experience
18
CAUTION
Do not place anything on top of this unit or block the heat radiation vents in any way. In particular, do not place tape decks or CD/DVD players on this unit as heat radiated from it can damage your software.
NO
Supplied accessories
Please check and identify the supplied accessories.
AC mains lead...................................................................1
For Continental Europe
(RJA0019-2K)
For the United Kingdom
(VJA0733)
For Australia and New Zealand
(RJA0035-X)
AM loop antenna set (RSA0012) .....................................1
(AM loop antenna, antenna holder, screw)
FM indoor antenna (RSA0007-L) .....................................1
Antenna plug (SJP9009) ..................................................1
(Only for the United Kingdom)
Antenna plug (RFE0014) ..................................................1
(Only for Australia and New Zealand)
Batteries ............................................................................2
Safety precautions
Placement
Set the unit up on an even surface away from direct sunlight, high temperatures, high humidity, and excessive vibration. These conditions can damage the cabinet and other components, thereby shortening the unit’s service life.
Do not place heavy items on the unit.
Voltage
Do not use high voltage power sources. This can overload the unit and cause a fire.
Do not use a DC power source. Check the source carefully when setting the unit up on a ship or other place where DC is used.
AC mains lead protection
Ensure the AC mains lead is connected correctly and not damaged. Poor connection and lead damage can cause fire or electric shock. Do not pull, bend, or place heavy items on the lead.
Grasp the plug firmly when unplugging the lead. Pulling the AC mains lead can cause electric shock.
Do not handle the plug with wet hands. This can cause electric shock.
Foreign matter
Do not let metal objects fall inside the unit. This can cause electric shock or malfunction.
Do not let liquids get into the unit. This can cause electric shock or malfunction. If this occurs, immediately disconnect the unit from the power supply and contact your dealer.
Do not spray insecticides onto or into the unit. They contain flammable gases which can ignite if sprayed into the unit.
Service
Do not attempt to repair this unit by yourself. If sound is interrupted, indicators fail to light, smoke appears, or any other problem that is not covered in these operating instructions occurs, disconnect the AC mains lead and contact your dealer or an authorized service center. Electric shock or damage to the unit can occur if the unit is repaired, disassembled or reconstructed by unqualified persons.
Extend operating life by disconnecting the unit from the power source if it is not to be used for a long time.
Remote control .................................................................1
SA-DX1050
(EUR7702KC0)
SA-DX950 for Europe
(EUR7702030)
SA-DX950 for Australia and New Zealand
(EUR7702040)
Refer to the separate booklet, “Remote Control”, for remote control operation details.
Use the numbers indicated in parentheses when asking for replacement parts.
3
RQT5802
4
RQT5802
Caution for AC Mains Lead
(For United Kingdom)
(“EB” area code model only)
For your safety, please read the following text carefully.
This appliance is supplied with a moulded three pin mains plug for your safety and convenience.
A 5-ampere fuse is fitted in this plug.
Should the fuse need to be replaced please ensure that the replacement fuse has a rating of 5-ampere and that it is approved by ASTA or BSI to BS 1362.
Check for the ASTA mark or the BSI mark on the body of the fuse.
If the plug contains a removable fuse cover you must ensure that it is refitted when the fuse is replaced.
If you lose the fuse cover the plug must not be used until a replacement cover is obtained.
A replacement fuse cover can be purchased from your local dealer.
CAUTION!
IF THE FITTED MOULDED PLUG IS UNSUITABLE
FOR THE SOCKET OUTLET IN YOUR HOME
THEN THE FUSE SHOULD BE REMOVED AND
THE PLUG CUT OFF AND DISPOSED OF
SAFELY.
THERE IS A DANGER OF SEVERE ELECTRICAL
SHOCK IF THE CUT OFF PLUG IS INSERTED
INTO ANY 13-AMPERE SOCKET.
If a new plug is to be fitted please observe the wiring code as stated below.
If in any doubt please consult a qualified electrician.
IMPORTANT
The wires in this mains lead are coloured in accordance with the following code:
Blue: Neutral, Brown: Live.
As these colours may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows:
The wire which is coloured Blue must be connected to the terminal which is marked with the letter N or coloured Black or Blue.
The wire which is coloured Brown must be connected to the terminal which is marked with the letter L or coloured Brown or Red.
WARNING: DO NOT CONNECT EITHER WIRE TO
THE EARTH TERMINAL WHICH IS MARKED WITH
THE LETTER E, BY THE EARTH SYMBOL OR
COLOURED GREEN OR GREEN/YELLOW.
THIS PLUG IS NOT WATERPROOF–KEEP DRY.
Before use
Remove the connector cover.
How to replace the fuse
The location of the fuse differ according to the type of
AC mains plug (figures A and B). Confirm the AC mains plug fitted and follow the instructions below.
Illustrations may differ from actual AC mains plug.
1. Open the fuse cover with a screwdriver.
Figure A
Figure B
2. Replace the fuse and close or attach the fuse cover.
Figure A
Fuse
(5 ampere)
Figure B
Fuse cover
Fuse
(5 ampere)
Control reference guide
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
SFC MODE
A
SPEAKERS
B
WAKE
RDS TIMER
MODE
TIME
TUNING
MEMORY
PTY SELECTOR
PRESET
DISPLAY MODE
DSP SOUND MODE
BAND FM MODE
EON PTY SEARCH
PHONES
DOWN
VOLUME
TAPE/MD
(TAPE MONITOR)
VCR1/VCR2 TV
INPUT
DVD CD TUNER
INPUT SELECTOR
PHONO
DIGITAL INPUT
UP
TAPE MONITOR
HELP
RESET
BASS/TREBLE
–
BALANCE L
DVD 6CH INPUT
+
R
VCR 1
VCR 2
VIDEO IN L AUDIO IN R
VCR 2
29 30 31
17 18 19 20 21 22 23 24 25 26 27 28
SPEAKERS
A B LOW IMP
TUNED
STEREO
MONO M
SLEEP
WAKE
RDS
RT
PS
PTY
EON kHz
MHz
L
LS
C R
S LFE RS
FIXED
PCM
DIGITAL
PRO LOGIC
SOUND MODE SFC
STEREO SURROUND
Refer to the separate booklet,“Remote
Control”, for a guide to the remote control’s buttons.
32
Reference pages are given in parentheses.
Main unit q Standby/on switch [ 8 ] ........................................................(13)
Press to switch the unit from on to standby mode or vice versa.
In standby mode, the unit is still consuming a small amount of power.
w Standby indicator [ ^ ]
When the unit is connected to the AC mains supply, this indicator lights up in standby mode and goes out when the unit is turned on.
e Wake indicator [WAKE] .......................................................(27) r Speaker select buttons [SPEAKERS, A, B]..................(13, 18)
SA-DX1050 only
MOS-FET light [MOS-FET] ...................................................(12)
Only for Europe
RDS button [RDS].................................................................(24)
For Australia and New Zealand
Timer button [TIMER, -MODE, –TIME] ................................(27)
For Europe
Timer button [TIMER, -MODE, –TIME] ................................(27) i Memory button [MEMORY] ..................................................(23) o SFC mode selector [SFC MODE] ........................................(18)
!
DSP sound mode select button
[DSP SOUND MODE] ............................................................(18)
!
Volume control [VOLUME] ..................................................(18)
SA-DX1050 only
Input indicators [INPUT] ......................................................(18)
!
Input selector [INPUT SELECTOR] ...............................(13, 18)
!
Digital input select button/indicator [DIGITAL INPUT]......(18)
!
Help/reset button [-HELP, –RESET]....................................(28)
!
DVD 6ch input select button/indicator [DVD 6CH INPUT] .....(19)
!
Headphone jack [PHONES] .................................................(20)
For Europe
Tuning/PTY select buttons
[TUNING, PTY SELECTOR, 2 , 1 ]..................................(22, 24)
For Australia and New Zealand
Tuning buttons [TUNING 2 , 1 ] ...........................................(22)
For Europe
Preset channel/display mode button
[PRESET, DISPLAY MODE] ...........................................(23, 24)
For Australia and New Zealand
Preset channel buttons [PRESET] ......................................(23)
33 34 35 36 37 38 39 40 41
For Europe
Band select/EON button [BAND, EON].........................(22, 25)
For Australia and New Zealand
Band select buttons [BAND] ...............................................(22)
For Europe
FM mode select/PTY search button
[FM MODE, PTY SEARCH] .............................................(22, 24)
For Australia and New Zealand
FM mode select button [FM MODE] ....................................(22)
@ Display section
@ Tape monitor button [TAPE MONITOR]..............................(21)
@ Tone and balance select button
[BASS/TREBLE, BALANCE] ................................................(20)
SA-DX950 only
Tape monitor indicator ........................................................(21)
@ Tone and balance adjust buttons [–, +, L, R] .....................(20)
SA-DX1050 only
VCR 2 terminals [VCR 2] ........................................................(6)
SA-DX1050 only
VCR 1/VCR 2 select button [VCR 1 l , VCR 2 k ] ...............(20)
Display section
@ Display
# Frequency unit indicators [kHz, MHz] ................................(22)
# Program format indicators [L, C, R, LS, S, LFE, RS].........(18)
# Front speaker indicators [-SPEAKERS-, Å , ı ].................(18)
# Low impedance indicator [LOW IMP] .................................(14)
# Tuned indicator [TUNED].....................................................(22)
# Stereo indicator [STEREO] ..................................................(22)
# Monaural indicator [MONO].................................................(22)
# Memory indicator [ ˜ ] ..........................................................(23)
# Timer indicators [SLEEP, WAKE] .......................................(27)
Only for Europe
RDS indicators [ RDS , PS, RT, PTY, EON] .........................(24)
$ Signal format indicators
[FIXED, PCM, , % DIGITAL, % PRO LOGIC] .....(16, 18)
$ DSP sound mode indicators
[-SOUND MODE-, SFC, STEREO, SURROUND] .................(18) 5
RQT5802
Connections
Stereo phono cable
White (L)
Red (R)
Video connection cable
To connect equipment, refer to the appropriate operating instructions.
Peripheral equipment and cables sold separately unless otherwise indicated.
Note
¡ Turn off all components before making any connections.
¡ Use digital connection to enjoy Dolby Digital or DTS ( \ page 18).
¡ Use analogue connection to enjoy sources that cannot be decoded on this unit and to record a source ( \ pages 16, 19 and
26).
Connecting video equipment
LOOP ANT
HOLDER
S-VIDEO
TV VCR1 DVD
MONITOR
OUT
IN IN
SA-DX1050 only
The S-VIDEO terminals
Connections through these terminals provide higher quality pictures than through the video terminal.
Note
+
Video signals input into the VIDEO terminals cannot be output from
R
FRONT
A L
S-VIDEO terminals or vice versa.
FM
ANT
75
Ω
LOOP
EXT
AM
ANT
L
R
OPTICAL1
(TV)
DIGITAL IN
OPTICAL2
(DVD)
COAXIAL
PHONO
GND
TV VCR1
MONITOR
OUT
IN
DVD/DVD 6CH
CENTER SURROUND
L
CD TAPE/MD
REC
(OUT)
PLAY
(IN)
TV
IN
OUT IN
FRONT
IN
SUBWOOFER
R
SUBWOOFER
OUT
L
R
– a DVD player
SPEAKERS
HAUT – PARLEURS
R L
CENTER FRONT
(CENTER, SUBWOOFER)
AUDIO OUT
(SURROUND L, R)
AC OUTLET
+
VIDEO OUT
–
AC IN
AUDIO OUT (FRONT L, R)
Note
Connect to FRONT L, R if your DVD player does not have 6 channel output.
VIDEO IN VIDEO OUT
AUDIO
OUT
AUDIO
IN
VIDEO
OUT b TV or monitor
Connection with 21 pin scart cable
TV
MONITOR
OUT
VCR1
VIDEO
IN c VCR
AUDIO
OUT
SA-DX1050 only
Connecting to the VCR 2 terminals on the front panel
TV
IN
OUT IN
6
RQT5802
CD TUNER
INPUT SELECTOR
PHONO
DIGITAL INPUT
VIDEO
IN
VIDEO
OUT
AUDIO
OUT
AV IN
AUDIO
IN
AUDIO
OUT d 21 pin scart cables
AV IN
VIDEO
OUT
TAPE
(MONITOR)
VCR1/V
VIDEO
IN
OFER LEVEL DVD 6CH INPUT
–
L
+
R
VCR 1
VCR 2
VIDEO IN L AUDIO IN R
VCR 2 e TV or monitor f VCR
VIDEO
OUT
AUDIO
OUT g Video camera, etc.
Optical fiber cable Coaxial cable
Connecting audio equipment
a Turntable
OUTPUT GND
LOOP ANT
HOLDER
S-VIDEO
TV VCR1 DVD
MONITOR
OUT
IN IN b Only for turntable with ground terminal.
FM
ANT
75
Ω
LOOP
EXT
AM
ANT
L
R
OPTICAL1
(TV)
DIGITAL IN
OPTICAL2
(DVD)
COAXIAL
GND
TV
MONITOR
OUT
VCR1
IN
DVD/DVD 6CH
OUTPUT
L
PHONO CD TAPE/MD
REC
(OUT)
PLAY
(IN)
TV
IN
OUT IN
FRONT
IN
SUBWOOFER
R
SUBWOOFER
(OUT)
L
R
+
R
FRONT
A L c CD player
–
SPEAKERS
HAUT – PARLEURS
SURROUND CENTER
R L
FRONT
R B L
+
– d Tape or MD deck
Note
If you have a graphic equalizer, connect it to the TAPE/MD
(or TAPE) terminals ( \ page 21).
Connecting digital equipment
e Satellite receiver, etc.
Optical fiber cable connection h Dust cap
¡ Do not bend the optical fiber cable.
¡ If the digital optical connector is not going to be used, be sure to attach the dust cap to prevent exposure to dust.
Note
This unit cannot decode Dolby Digital
RF (radio frequency) signals from a laser disc player.
PLAY (OUT)
REC (IN)
DIGITAL OUT Changing the digital input settings
You can change the input settings for the digital terminals if necessary (for example, if your CD player doesn’t have a coaxial output terminal). Note the equipment you have connected to the terminals, then change the settings ( \ pages 12–13).
LOOP ANT
HOLDER
S-VIDEO
TV VCR1 DVD
MONITOR
OUT
IN IN
FM
ANT
75
Ω
LOOP
EXT
AM
ANT
L
R
DIGITAL IN
OPTICAL1
(TV)
OPTICAL2
(DVD)
PHONO
GND
COAXIAL
TV
MONITOR
OUT
VCR1
IN
DVD/DVD 6CH
CENTER SURROUND
L
CD TAPE/MD
REC
(OUT)
PLAY
(IN)
TV
IN
OUT IN
FRONT
IN
SUBWOOFER
OUT
(OUT)
L
R
R
FRONT
A L
+
–
SPEAKERS
HAUT – PARLEURS
SURROUND CENTER
R L
FRONT
R B L
–
+ f CD player g DVD player
DIGITAL OUT
7
RQT5802
8
RQT5802
Connections
Antenna connections
FM antenna
Fix the other end of the antenna where reception is best.
a FM indoor antenna (included) b Adhesive tape
1 2
LOOP ANT
HOLDER
S-VIDEO
TV VCR1
MONITOR
OUT
IN
OPTICAL1
(TV)
DIGITAL IN
OPTICAL2
(DVD)
COAXIAL
TV
MONITOR
OUT
VCR1
FM
ANT
75
Ω
LOOP
EXT
AM
ANT
L
R
PHONO CD
REC
(OUT)
TAPE
PLAY
(IN)
TV
IN
(OUT)
GND
3
When mounting the antenna to a column, wall or rack d Screw
(included) c AM loop antenna (included)
AM loop antenna
¡ Fit the AM loop antenna holder
(included) onto the rear panel of this unit and then attach the AM loop antenna to it (facing in the direction of best reception).
¡ Keep the antenna cord away from tape decks, DVD players, and other cords.
To connect an outdoor antenna e Vinyl-covered wire
5–12 m
AM outdoor antenna
¡ Run a piece of vinyl wire horizontally across a window or other convenient location.
¡ Leave the loop antenna connected.
¡ Disconnect the antenna when the unit is not in use. Do not use the antenna during an electrical storm.
LOOP ANT
HOLDER
S-VIDEO
TV VCR1
MONITOR
OUT
IN
OPTICAL1
(TV)
DIGITAL IN
OPTICAL2
(DVD)
COAXIAL
TV
MONITOR
OUT
VCR1
FM
ANT
75
Ω
LOOP
EXT
AM
ANT
L
R
PHONO CD
REC
(OUT)
TAPE
PLAY
(IN)
TV
IN
(OUT)
GND
FM outdoor antenna
¡ Disconnect the FM indoor antenna.
¡ The antenna should be installed by a competent technician.
For Europe
How to use the antenna plug (included)
Only for Australia and New Zealand
Two types of wire are most commonly used for connection from the antenna: 300
Ω parallel feeder wire or 75
Ω coaxial cable. For best resistance to outside interference, the use of 75
Ω coaxial cable is suggested.
¡ To connect a 75
Ω coaxial cable q Remove a piece of the outer vinyl insulator.
a
20 mm 10 mm w Carefully pull the tabs apart to remove the cover.
LOOP ANT
HOLDER a FM outdoor anntena
S-VIDEO
TV VCR1
MONITOR
OUT
IN b 75
Ω coaxial cable
FM
ANT
75
Ω
LOOP
EXT
AM
ANT
L
R
OPTICAL1
(TV)
DIGITAL IN
OPTICAL2
(DVD)
COAXIAL
PHONO CD
REC
(OUT)
TAPE
PLAY
(IN)
TV
MONITOR
OUT
VCR1
[Only for the United Kingdom]
Antenna plug (included)
TV
IN
FM outdoor anntena
GND
75
Ω coaxial cable
300
Ω feeder wire
Antenna plug (included) e Remove the lead wire and clamp it with the plastic bar.
Lead wire
Plastic bar r Install the coaxial cable.
Clamp the cable conductor, and wind it on so that it doesn’t contact anything else.
Press down with pliers.
t Attach the cover.
¡ To connect a 300
Ω feeder wire
Loosen the screws, connect the wires, and tighten the screws to secure the connection.
300
Ω
feeder wire
(not included)
Connecting the AC mains lead and other information
(FOR THE UNITED KINGDOM ONLY)
READ THE CAUTION FOR THE
AC MAINS LEAD ON PAGE 4
BEFORE CONNECTION.
R
FRONT
A L c Cooling fan
The cooling fan operates at high power output levels only.
LEURS
SURROUND CENTER
R L
FRONT
R B L
AC IN
AC mains lead
Connect this lead only after all other cables and cords are connected.
Note
The included AC mains lead is for use with this unit only. Do not use it with other equipment.
Insertion of Connector
Even when the connector is perfectly inserted, depending on the type of inlet used, the front part of the connector may jut out as shown in the drawing.
However there is no problem using the unit.
f Connector d AC mains lead
(included) e To household mains socket g Approx. 6 mm h Appliance inlet
9
RQT5802
10
RQT5802
Speaker connections
Placement of speakers
a Center speaker b Front speaker
(left) c Front speaker
(right)
30
°
30
° d Subwoofer
120
° e Surround speaker
(left) f Surround speaker
(right)
The front, center, and surround speakers should be placed at approximately the same distance from the seating area. The angles in the diagram are approximate.
Connecting speakers
Other connections are possible depending on your speaker system.
See your speaker system’s operating instructions for details.
Front speakers
Front speakers
Place on the left and right of the TV at seated ear height so that there is good coherency between the picture and sound.
Center speaker
Place underneath or above the center of the TV. Aim the speaker at the seating area.
Surround speakers
Place on the side of or slightly behind the seating area, about one meter higher than ear level.
Subwoofer
The subwoofer can be placed in any position as long as it is at a reasonable distance from the TV.
Note that some experimentation can yield the smoothest low frequency performance. Placement near a corner can increase the apparent output level, but can result in unnatural bass.
g Front speaker
(right) h Front speaker
(left)
Speaker impedance:
A or B: 4-16
Ω
A and B: 8-16
Ω i Speaker cables
Note
If you connect speakers with an impedance under 6
Ω
, switch on “LOW IMP” ( \ page 14).
LOOP ANT
HOLDER
1 2 3
S-VIDEO
TV VCR1 DVD
MONITOR
OUT
IN IN
FM
ANT
75
Ω
GND
LOOP
EXT
AM
ANT
L
R
OPTICAL1
(TV)
DIGITAL IN
OPTICAL2
(DVD)
COAXIAL
PHONO
GND
TV
MONITOR
OUT
VCR1 DVD/DVD 6CH
CENTER SURROUND
IN
L
CD
REC
(OUT)
TAPE
PLAY
(IN)
TV
IN
(OUT) (IN)
FRONT
IN
SUBWOOFER
R
SUBWOOFER
OUT
L
R
FRONT
R A L
+
–
SPEAKERS
SURROUND
R L
CENTER
FRONT
R B L
+
–
1 2
AC IN
AC OUTLET
3
“B” terminals
For connection to a second pair of speakers.
Note
Use the A terminals to enjoy SURROUND, SFC and DVD 6CH INPUT.
Center speaker
Speaker impedance: 6-16
Ω
S-VIDEO
TV VCR1 DVD
MONITOR
OUT
IN IN
2
L IN a
TV
MONITOR
VCR1
Center speaker
OUT
DVD/DVD 6CH
CENTER SURROUND
IN L
REC
(OUT)
TAPE
PLAY
(IN)
TV
IN
(OUT) (IN)
FRONT
IN
SUBWOOFER
R
SUBWOOFER
(OUT)
L b Speaker cable
R
FRONT
R A L
+
–
SPEAKERS
SURROUND
R L
CENTER
FRONT
R B L
+
–
Surround speakers
Speaker impedance: 6-16
Ω
S-VIDEO
TV VCR1 DVD
MONITOR
OUT
IN IN c Surround speaker (right)
TAL IN
CAL2
VD)
COAXIAL
TV
MONITOR
OUT
VCR1
IN
DVD/DVD 6CH
CENTER SURROUND
L
CD
REC
(OUT)
TAPE
PLAY
(IN)
TV
IN
(OUT) (IN)
FRONT
IN
SUBWOOFER
R
SUBWOOFER
(OUT)
L
R d Speaker cable
R
FRONT
A L
+
–
SPEAKERS
SURROUND
R L
CENTER FRONT
R B L
+
–
AC IN
AC IN
Subwoofer e Surround speaker (left) f Speaker cable
LOOP ANT
HOLDER
S-VIDEO
TV VCR1 DVD
MONITOR
OUT
IN IN
FM
ANT
75
Ω
LOOP
EXT
AM
ANT
L
R
OPTICAL1
(TV)
GND
DIGITAL IN
OPTICAL2
(DVD)
COAXIAL
TV
MONITOR
OUT
VCR1
IN
DVD/DVD 6CH
CENTER SURROUND
L
PHONO CD TAPE/MD
REC
(OUT)
PLAY
(IN)
TV
IN
OUT IN
FRONT
IN
SUBWOOFER
R
SUBWOOFER
OUT
L
R
FRONT
R A L
+
–
SPEAKERS
HAUT – PARLEURS
SURROUND
R L
CENTER FRONT
R B L
INPUT
+
– h Monaural connection cable g Active subwoofer
Note
This receiver does not have an amplifier for the subwoofer.
To connect a passive subwoofer
AC
¡ Connect another amplifier and connect
Or the subwoofer to it.
¡ Connect a passive subwoofer that has front speaker terminals
(See the operating instructions of the speaker system for details.)
11
RQT5802
12
RQT5802
FRONT CENTER
SUB-WFR SURROUND
FRONT CENTER
SURROUND
CD
100 150 200
OFF STANDARD MAX
TV
DVD
OFF ON
FRONT SMALL
CENTER, SURROUND
NONE SMALL
LARGE
LARGE
SUB-WFR NO YES
1.0 m 10.0 m
Customizing your receiver
Change the settings to suit your speakers and equipment and to suit the environment in which the unit is to be used. Before making any changes, read the following descriptions, note the factory settings and ranges, and refer to the instructions for the speakers and equipment.
The settings remain intact until they are changed, even after the power is turned off.
Setting descriptions
SIZE
Change to suit the speakers you have connected.
LARGE: For speakers that can reproduce a full sound range, particularly the bass range below 100 Hz.
SMALL: For speakers that cannot adequately reproduce the bass range. This setting is sufficient for most speakers if you are using a subwoofer.
NONE: For speakers you haven’t connected (center or surround).
The factory settings are: Front: LARGE
Center and surround: SMALL
For the subwoofer, select YES if you have connected one (factory setting), or NO if you have not.
DISTANCE
Enter the distance of the speakers from the seating position so that the sound from all the speakers (except for the subwoofer) reaches you at the same time.
You can select distances between 1.0 and 10.0 m at 0.1 m intervals.
The factory settings are: Front and center: 3.0 m
COAX OPT1 OPT2
FILTER
This setting allows you to change the cut-off for bass output from the front speakers. If you set the front speakers to “SMALL”, the filter is set to 100 Hz. Raise the cut-off if the bass from the front speakers is unsatisfactory so that this bass is output through the subwoofer.
You can raise the cut-off from 100 Hz to either 150 Hz or 200 Hz.
DR COMP - Dynamic range compression
Change this setting to view software at low volume (such as late at night) and maintain audio clarity. This setting works with Dolby
Digital software. It reduces the peak level in loud scenes without affecting the sound field.
OFF: The software is played with the original dynamic range
(factory setting).
STANDARD: The level recommended by the producer of the software for household viewing.
MAX: The maximum allowable compression (recommended for night viewing).
D-INPUT - Digital input
Change these settings to suit the connections you have made to the three digital input terminals, COAX, OPT1, and OPT2 ( \ page 7), so that the correct source is selected when you turn [INPUT
SELECTOR] ( \ page 18).
The factory settings are: CD: COAX
DVD: OPT2
TV: OPT1
DIMMER
This setting allows you to dim the unit’s display (and turn off the
MOS-FET light on SA-DX1050) for better viewing in a darkened room.
The factory setting is OFF (normal brightness).
1
2
3
4
5
3
SPEAKERS
A B
SPEAKERS
A
1
4
2,5
SIZE, DISTANCE, D-INPUT
SPEAKERS
B
FILTER, DR COMP, DIMMER
INPUT SELECTOR
SPEAKERS
A B
4
INPUT SELECTOR
Customizing your receiver
Basic steps
If you allow about 10 seconds to elapse between settings, the procedure is canceled, all settings are returned to how they were, and the previous display is restored. Begin again if this occurs.
1
Press [
8
].
2
Press [A] and [B] at the same time.
3
Press [A] to select the item you want to change.
Each time you press the button:
SIZE / DISTANCE / FILTER / DR COMP / D-INPUT / DIMMER
↑
4
Change the settings (
a
below).
Repeat steps 3 and 4 to complete the necessary settings.
5
Press [A] and [B] at the same time.
Changing the settings
SIZE
1 Press [B] to select the speaker you want to set.
Each time you press the button:
FRONT / CENTER / SURROUND / SUB-WFR (Subwoofer)
↑
2 Turn [INPUT SELECTOR] to change the setting.
When you turn the selector:
FRONT: SMALL , LARGE
CENTER and SURROUND: NONE , SMALL / LARGE
SUB-WFR: NO , YES
3 Repeat 1 and 2 to change other SIZE settings.
DISTANCE
1 Press [B] to select the speaker you want to set.
Each time you press the button:
FRONT / CENTER / SURROUND
↑
2 Turn [INPUT SELECTOR] to set the distance.
3 Repeat 1 and 2 to change other DISTANCE settings.
FILTER
Turn [INPUT SELECTOR] to set the cut-off.
When you turn the selector:
100 , 150 / 200
DR COMP
Turn [INPUT SELECTOR] to change the setting.
When you turn the selector:
OFF , STANDARD / MAX
D-INPUT
1 Press [B] to select the input position you want to set.
Each time you press the button:
CD COAX / DVD OPT2 / TV OPT1
↑
These are the factory settings. Actual displays depend on the changes you make. If you change one setting, the other corresponding setting will also change.
2 Turn [INPUT SELECTOR] to change the setting.
When you turn the selector:
COAX , OPT1 ,
↑
/ OPT2
↑
3 Repeat 1 and 2 to change other D-INPUT settings.
DIMMER
Turn [INPUT SELECTOR] to change the setting.
When you turn the selector:
OFF , ON
13
RQT5802
14
RQT5802
SPEAKERS A, B
SPEAKERS
A B
SPEAKERS
A LOW IMP
Customizing your receiver
For front speakers with an impedance under 6
Ω
Turn “LOW IMP“ on if even one of your speakers has an impedance under 6
Ω
.
Press and hold [A] or [B] until “LOW IMP” lights up on the display.
Press and hold down again to cancel “LOW IMP”.
Note that when “LOW IMP” is on, SPEAKERS A and B cannot be used at the same time.
1
2
3
4
TEST
LEVEL
1
SPEAKERS
A
4
DISPLAY RETURN
/ /
DELAY LEVEL – +
SUBWOOFER SOUND MODE SFC TEST
TV/AV
–
TV VOL
+
MUTING
– VOLUME +
–
VOLUME
+
SPEAKERS
A
5
2,6
3
L C R RS LS SW
Adjusting speaker output level
Adjust the level of the speakers so they are the same apparent level as the front speakers when you are sitting where you would normally enjoy a source.
1
Press [A] to turn on SPEAKERS A.
You cannot adjust output level when SPEAKERS B is on.
2
Press [TEST] to output the test signal.
DSP sound mode switches to SURROUND mode.
The signal is output from each speaker in order for about two seconds each:
L: Front speaker (left)
C: Center speaker
R: Front speaker (right)
RS: Surround speaker (right)
LS: Surround speaker (left)
SW: Subwoofer
Speakers set as “NONE” or “NO” are skipped.
Note
The test signal will not be output if DSP is defeated ( \ page 22) or DVD 6CH INPUT is on ( \ page 19).
3
Adjust the volume to the level normally used.
Adjust the balance of the front speakers if necessary
( \ page 20).
4
Press [LEVEL] to select the speaker channel to adjust.
The current level appears on the display.
Press again to change the speaker channel.
Speakers set as “NONE” or “NO” are skipped.
5
Press [–] or [+] to adjust the level to the same apparent level as the front speakers.
C, RS, and LS can be adjusted between –10 dB and +10 dB, with zero being the current level of the front speakers.
SW can be set to MIN, between 1 to 19, or MAX.
Repeat steps 4 and 5 for each speaker channel.
6
Press [TEST] to stop the test signal.
For your reference
Subwoofer output is easily influenced by the source played. You can achieve better results by adjusting its output while listening to a source ( \ page 21).
5
– +
6
TEST
15
RQT5802
16
RQT5802
A
B
C
DSP SOUND MODE
DSP SOUND MODE
DSP SOUND MODE
DIGITAL INPUT
SPEAKERS
A
SPEAKERS
A
DIGITAL INPUT
L
SOUND MODE
STEREO
R
L
LS
C R
LFE RS
DIGITAL
SOUND MODE
SURROUND
FIXED
PCM
FIXED
DSP sound modes
The digital sound processor (DSP) in this unit can decode Dolby
Digital and DTS digital signals. It automatically determines the type of signal, PCM, Dolby Digital, or DTS, and processes it accordingly.
The DSP can add surround-like effects to stereo sources (analogue or PCM signals).
Choose from the STEREO, SURROUND, or SFC modes.
The DSP may interfere with radio reception. You can turn it off if this occurs ( \ page 22).
Output is in stereo when you turn the DSP off so sound is only heard through the front speakers.
Note
¡ PCM with a sampling frequency of 44.1 kHz is the digital signal format normally found on CDs. Some DVDs also use this format but often with a higher sampling rate.
¡ This unit cannot process other digital signal formats, such as
PCM signals with sampling frequencies of 96 kHz and 192 kHz and MPEG.
A
STEREO mode
Use this mode to play digital or analogue stereo sources or to play surround sources through two speakers. When surround sources are played in this mode, the sounds intended for the other speaker channels are played through the front speakers.
B
SURROUND mode
Select this mode when you are playing a digital surround source
(Dolby Digital or DTS) or an analogue source that is recorded with
Dolby Surround (VCR, for example).
C Changing the recognition mode
In rare cases, the unit may have trouble recognizing the digital signals on discs. With the PCM signals on CDs, this may cause the beginning of a track to be cut off. Engage the PCM FIX mode if this occurs. With DTS, the signals may not be recognized at all.
Engage the DTS FIX mode if this occurs.
This mode does not need to be changed under normal circumstances. Change it only if the unit appears to be having trouble recognizing the software you are playing.
While the input source is selected and digital input is engaged:
Press and hold [DIGITAL INPUT].
The current mode is displayed. Press again to change the mode.
Each time you press the button:
AUTO / PCM FIX / DTS FIX
↑
When a FIX mode is on, the unit cannot process other signals. This may cause noise to be output. Select “AUTO” if this occurs.
The selected mode is stored even if the unit is turned off.
A
B
DSP SOUND MODE
SFC MODE DSP SOUND MODE
SPEAKERS
A
SFC MODE
1
1
TV VCR DVD
MD
1
TUNER/BAND
2
TAPE CD
3
DIRECT TUNING/
DISC
4 5 6 ≥
10/-/--
7 8 9 0
TOP MENU MENU
ENTER
DISPLAY RETURN
/ /
DELAY LEVEL – +
SUBWOOFER SOUND MODE SFC TEST
TV/AV
–
TV VOL
+
MUTING
–
VOLUME
+
2 2
SOUND MODE SFC
DSP sound modes
A
SFC modes
Enjoy an enhanced sound experience with greater presence and spread by using these SFC (sound field control) modes with PCM or analogue stereo sources.
The SFC modes cannot be used if the input signal is Dolby Digital or DTS.
Choose from the following modes.
HALL
Imparts the reflection and spread of a large concert hall.
CLUB
Conveys the exciting and intimate atmosphere of a jazz club.
LIVE
Brings you up close for “live” stage performance and smoother vocals.
THEATER
Recreates natural sound ambience and direction.
SIM SURR (Simulated Surround)
Heightens the sensation of expanded space with stereo sources, and augments monaural sources.
B Adjusting the sound field
You can adjust the sound field by adjusting the level of the speakers and the delay time of the surround speakers. These adjustments can be made for each SFC mode.
To adjust the speaker level
1 Press [LEVEL] to select the speaker channel.
Each time you press the button:
C / RS / LS / SW
↑
Speakers set as “NONE” or “NO” are skipped.
2 Press [–] or [+] to adjust the level.
C, RS, and LS:
–10 dB to +10 dB
SW:
--- (off) , MIN , 1 – 19 , MAX
To adjust the delay time
1 Press [DELAY].
2 Press [–] or [+] to change the delay time.
Delay time can be set at 10-millisecond (ms) intervals between
10 and 100 ms.
The factory setting is 50 ms for each mode.
17
RQT5802
18
RQT5802
1
2
3
4
6
1 2 4
-
2
4
-
1
6
SPEAKERS
A
1
DSP SOUND MODE
2
SFC MODE
DOWN
INPUT SELECTOR
SPEAKERS
A
VOLUME
UP
SPEAKERS
A
3
DIGITAL INPUT
L
LS
C R
LFE RS
DIGITAL
SOUND MODE
SURROUND
Enjoying the sounds
1
Press [
8
].
2
Press [SPEAKERS A].
“SURROUND” and “SFC” do not work if you select “B”.
3
Turn [INPUT SELECTOR] to select the input source.
(SA-DX1050) The indicator corresponding to the selected source lights.
To switch between analogue and digital input (CD,
DVD, and TV)
Press [DIGITAL INPUT].
Each time you press the button:
ANALOG , DIGITAL
The indicator lights when you select “DIGITAL”.
Once you have set the mode for a source, that mode is engaged whenever you select that source.
4
Select the DSP sound mode.
1 Press [DSP SOUND MODE].
The indicator corresponding to the mode lights.
Select the mode appropriate to the source ( \ pages 16–17).
2 When you select “SFC”
Turn [SFC MODE].
Once you have set the mode for a source, that mode is engaged whenever you select that source.
5
Start playing the source.
Refer to the equipment’s instructions for details.
6
Adjust the volume.
When you finish listening
Be sure to reduce the volume and press [ 8 ] to switch the unit to standby.
For your reference
¡ If you are using a VCR and you select TAPE/MD (or TAPE),
CD, TUNER, or PHONO
The picture will remain on the screen.
¡ The signal format indicators
The following indicators light depending on the source you are playing.
% DIGITAL:
Dolby Digital sources
:
DTS sources
% PRO LOGIC:
Analogue sources in SURROUND mode
Digital sources with PCM signals in SURROUND mode
Dolby Digital sources that contain Dolby Pro Logic in
SURROUND mode
¡ The program format indicators (L, C, R, LS, S, LFE, RS)
The program format indicators light up to indicate the channels contained in the digital input signal. They do not light when input is analogue.
L: Front channel (left)
C: Center channel
R: Front channel (right)
LS: Surround channel (left)
RS: Surround channel (right)
S: If the surround channel is monaural
LFE (Low Frequency Effect): Deep-bass effect
A
B
SPEAKERS B
DVD 6CH INPUT
SPEAKERS
B
SPEAKERS
B
DVD 6CH INPUT
Enjoying the sounds
A
To switch between DVD 2 channel and 6 channel input
There may be times when you need to use analogue input for DVD, such as to enjoy sources recorded with MPEG, linear PCM and multiple channel linear PCM.
Select the analogue input mode to suit the source.
DVD: For two-channel audio.
DVD 6CH: For multiple channel audio.
Press [DVD 6CH INPUT].
Each time you press the button:
DVD , DVD 6CH
Input switches automatically to DVD if you press this button while another source is selected.
The indicator lights when you select “DVD 6CH”.
Once you have set the mode, that mode is engaged whenever you select “DVD”.
Note
¡ DVD 6CH INPUT only works when SPEAKERS A is on and
SPEAKERS B is off.
¡ You cannot use any of the DSP sound modes while DVD 6CH
INPUT is on.
¡ Speaker settings ( \ page 13) are ineffective while DVD 6CH
INPUT is on. Change the settings on the DVD player if necessary.
B To use SPEAKERS B
Use SPEAKERS B if you have connected another set of speakers to the B terminals.
Sound will be heard in stereo while SPEAKERS B is on.
Press [B].
If you don’t want sound coming from the speakers connected to the
A terminals, press [A] to turn them off.
Manufactured under license from Dolby Laboratories.
“Dolby”, “Pro Logic” and the double-D symbol are trademarks of
Dolby Laboratories.
Confidential Unpublished Works. c 1992-1997 Dolby
Laboratories. All rights reserved.
Manufactured under license from Digital Theater Systems, Inc.
“DTS” and “DTS Digital Surround” are trademarks of Digital
Theater Systems, Inc. c 1996 Digital Theater Systems, Inc. All rights reserved.
19
RQT5802
A
1
BASS/TREBLE
BALANCE
2
–
L
+
R
B
C
VCR 1
VCR 2
1 2
BASS, TREBLE
–10 dB +10 dB
BALANCE
VCR 1
VCR 2
Enjoying the sounds
A
Adjusting the tone and balance
You can adjust the tone (BASS and TREBLE) only when the DSP sound mode is STEREO and input is either analogue or PCM. You cannot adjust the tone while the DSP is defeated or if DVD 6CH
INPUT is selected.
1
Press [BASS/TREBLE, BALANCE].
Each time you press the button:
BASS / TREBLE / BALANCE
↑
BASS: To adjust the bass
TREBLE: To adjust the treble
BALANCE: To adjust the left/right sound balance
2
Press [–, L] or [+, R].
–, L: to lower the selected tone or shift the balance to the left speaker.
+, R: to raise the selected tone or shift the balance to the right speaker.
The previous display returns after a few seconds.
B
Using the VCR 2 terminals
SA-DX1050 only
This button only works when “VCR 1” is selected as the input source.
Press [VCR 1
l
, VCR 2
k
] to select
“VCR 1
l
” or “VCR 2
k
”.
C
Using headphones
q Press [A] and/or [B] to turn off the speakers.
Turning the speakers off automatically engages STEREO mode and ensures no sound is heard from the subwoofer.
w
(Sound will seem unusual if you use another DSP mode.) w Reduce the volume.
e Connect the headphones (not included).
Plug type: 6.3 mm stereo r Adjust the volume.
Note
Avoid listening for prolonged periods of time to prevent hearing damage.
1 3 2 4
20
RQT5802 a Headphones
A
B
C
MUTING
SUBWOOFER
TAPE MONITOR
TAPE MONITOR
SA-DX1050
TAPE/MD
(TAPE MONITOR)
SA-DX950
TAPE MONITOR
LEVEL
SUBWOOFER
TV VCR DVD
MD
1
TUNER/BAND
2
TAPE CD
3
DIRECT TUNING/
DISC
4 5 6 ≥ 10/-/--
7 8 9 0
TOP MENU MENU
ENTER
DISPLAY RETURN
/ /
DELAY LEVEL – +
SUBWOOFER SOUND MODE SFC
TV/AV
TEST
–
TV VOL
+
MUTING
– VOLUME +
–, +
MUTING
Enjoying the sounds
A
Muting the volume
Press [MUTING].
The message “MUTING ON NOW” runs repeatedly from right to left across the display as long as the muting function is on.
To cancel
Press [MUTING].
Muting is also canceled when the unit is turned off.
B
Adjusting the subwoofer level
You can adjust the volume of the subwoofer while listening to a source. No sound is heard from the subwoofer if “SW ---” is selected. This setting can be done for each DSP mode.
You cannot adjust the subwoofer level while the DSP is defeated or if DVD 6CH INPUT is selected.
The factory setting is “SW 10”.
Press [SUBWOOFER].
The current setting is shown.
Each time you press the button:
SW --- / SW MIN / SW 5 / SW 10 / SW 15 / SW MAX
↑
To make finer adjustments
1 Press [LEVEL] to select “SW”.
2 Press [–] or [+].
Note
Sound from the subwoofer can be distorted if you raise the unit’s volume while subwoofer level is high. Reduce subwoofer level if this occurs.
C
Using the TAPE MONITOR
Use the tape monitor if you have connected a graphic equalizer to the TAPE/MD (or TAPE) terminals.
Press [TAPE MONITOR].
The “TAPE MONITOR” indicator lights and the tape monitor comes on.
Sources other than TAPE/MD (or TAPE) can still be selected with
[INPUT SELECTOR] while the “TAPE MONITOR” indicator is on.
Press [TAPE MONITOR] again to turn the tape monitor off.
( \ See “Making a recording” on page 26 for details on how to use the tape monitor during recording.)
Note
¡ The tape monitor cannot be used when input is digital and turns off if you select digital input.
¡ Depending on the setting, the graphic equalizer can cause distortion.
21
RQT5802
22
RQT5802
A
1
2
3
B
BAND
EON
TUNING
PTY SELECTOR
3 2
FM MODE DSP SOUND MODE
INPUT SELECTOR
TUNED
STEREO
1
3
TV VCR DVD
MD
1
TUNER/BAND
2
TAPE CD
3
DIRECT TUNING/
DISC
4
7
5
8
6 ≥ 10/-/--
9 0
TOP MENU MENU
ENTER
DISPLAY RETURN
/ /
DELAY LEVEL
– +
SUBWOOFER SOUND MODE SFC TEST
TV/AV
–
TV VOL
+
MUTING
– VOLUME +
2
1
MHz
MHz
The radio
A
Manual tuning
You can tune radio stations manually by selecting the station’s frequency, or you can preset up to 30 stations into channels to make tuning simpler ( \ page 23).
1
Turn [INPUT SELECTOR] to select
“TUNER”.
2
Press [BAND] to select “FM” or “AM”.
3
Press [TUNING
2
or
1
] to select the frequency of the station.
“TUNED” lights when tuned.
“STEREO” lights during FM stereo broadcasts.
Automatic tuning
Hold down [TUNING 2 or 1 ] until the frequency begins to scroll.
Tuning stops when a station is found. (Tuning may stop if there is interference.)
Improving reception
¡ FM mode
You can improve FM reception by switching reception to monaural.
Press [FM MODE].
“MONO” lights.
Press the button again to cancel.
¡ DSP DEFEAT
You can improve reception by turning off the DSP ( a page 16).
Press and hold [DSP SOUND MODE] until “DEFEAT” appears.
Press and hold [DSP SOUND MODE] again to turn the DSP on.
¡ For your reference
DVD players can interfere with radio reception. Turn the DVD player off or move it further away from the antennas if this occurs.
To change the AM frequency step
Press and hold [BAND] for about 3 seconds when AM band is selected. (The frequency step changes from 9 kHz to 10 kHz.)
To return to the previous step, press and hold [BAND] for about 3 seconds again.
B Direct tuning q Press [TUNER/BAND].
The band changes each time you press the button.
w Press [DIRECT TUNING/DISC].
e Press the numbered buttons to enter the frequency.
e.g. To select 107.90 MHz, press [1] / [0] / [7] / [9] / [0]
Note
1. If you do not press a button while the cursor is flashing, the display returns to the frequency being received.
2. If the frequency has not been input correctly, “ERROR” will be displayed.
MEMORY
A
C
B
D
A
1 3 2 4
MEMORY
2 1
M
M
≥
10/-/--, 1–0
TV VCR DVD
MD TUNER/BAND TAPE CD
1
4
2
5
3
DIRECT TUNING/
DISC
6 ≥
10/-/--
7 8 9 0
TOP MENU MENU
ENTER
DISPLAY RETURN
/ /
DELAY LEVEL
– +
SUBWOOFER SOUND MODE SFC TEST
TV/AV
–
TV VOL
+
MUTING
–
VOLUME
+
1
PRESET
DISPLAY MODE
2
TUNING
PTY SELECTOR
The radio
Preset tuning
Choose either automatic presetting, which presets the stations the tuner can receive, or manual presetting, which allows you to select the stations to preset and the order in which they are to be preset.
There are 30 channels available for presetting.
Remember
If a new station is preset into a channel, the old station is erased.
A Automatic presetting
Presetting FM stations
Preparation: Tune to the FM frequency where you want to begin presetting ( \ page 22).
Press and hold [MEMORY].
The FM stations the unit can receive are preset in channels 1 to 30.
Presetting AM stations
Preparation: Tune to the AM frequency where you want presetting to begin ( \ page 22).
Press and hold [MEMORY].
The AM stations the unit can receive are preset in channels 21 to
30. (FM stations are replaced if any were preset in these channels.)
During automatic presetting, the memory indicator flashes and the frequency scrolls. The memory indicator and channel numbers are displayed for a second when a station is preset ( ı ).
The last station to be preset is displayed when presetting finishes.
For your reference
Even if the AC mains lead is disconnected from the household mains socket, the stations remain in memory for approximately one month.
C Manual presetting
Preset the stations one at a time.
1 Tune to the station.
2 Press [MEMORY].
3 Press [TUNING 2 or 1 ] to select a channel.
4 Press [MEMORY].
D Selecting channels
1
Press [PRESET].
The channel number flashes for about 5 seconds.
2
Press [TUNING
2
or
1
].
Hold down the buttons to change channels faster.
On the remote control
Press the numbered buttons.
For channels 1 to 9, press the corresponding number.
For channels 10 or over, press [
≥
10/-/--], then the two digits.
e.g. To select channel 21
[
≥
10/-/--] / [2] / [1]
MHz
23
RQT5802
A
1
RDS
2
PRESET
DISPLAY MODE
1
2
3
4
B
1 2 3
1
RDS
2 TUNING
PTY SELECTOR
24
RQT5802
3 FM MODE
PTY SEARCH
1 2
RDS
RDS
RDS PS
RDS
PTY
RDS
RT
RDS
MHz
MHz
MHz
RDS broadcasts
Only for Europe
RDS (radio data system) is a multiplex broadcasting system where, along with FM audio signals, stations transmit other signals to help you enjoy radio more and tune into programs easier. This unit can use the following types of signals. Some stations do not have PTY,
EON, and RT.
¡ PS (Program service): Station name.
¡ PTY (Program type): Displays the program type ( a below) and is used to search for a type of program ( a page 25).
¡ EON (Enhanced other networks): This signal is used between networked stations to make it easier for you to tune into a type of program ( a page 25).
¡ RT (Radio text): This unit can show up to 64 letters by scrolling them across the display. This text could be about the song, traffic or weather, phone-in numbers, or police information.
Note
This unit does not have the emergency broadcasts system (EBS) that tunes automatically into emergency broadcasts.
A
To display RDS information
The display normally shows the radio frequency. “RDS” lights when the station is broadcasting RDS signals. You cannot change the display if "RDS" is off.
1
Press [RDS].
2
While “RDS” is flashing
Press [PRESET, DISPLAY MODE].
The display changes each time you press the button.
q Frequency display w PS display e PTY display (“NO PTY” if there are no PTY signals, then the frequency is shown again) r RT display (no change if there are no RT signals)
B
PTY search
PTY finds programs currently broadcasting from amongst the preset
FM stations. Preset FM stations before proceeding.
1
Press [RDS].
2
While “RDS” is flashing
Press [TUNING, PTY SELECTOR,
2
,
1
] to select the program type.
The display changes each time you press the button
( a page 25 for PTY displays).
3
While the PTY display is flashing
Press [FM MODE, PTY SEARCH].
The PTY indicator flashes while searching.
The unit switches to the station broadcasting the program.
The PTY indicator flashes for another two seconds.
“SELECT PTY FIRST” scrolls across the display if you try to start a PTY search without selecting a program type.
RDS
PTY
RDS
PTY
A
1
RDS
2
TUNING
PTY SELECTOR
3
BAND
EON
RDS
RDS
PTY
MHz
RDS broadcasts Only for Europe
A
EON tuning
EON puts the unit on standby to receive programs that are going to be broadcast on a station that shares RDS signals with the current station. Preset FM stations before proceeding. EON tuning does not work if the unit is not receiving EON signals (“NO EON” is displayed.)
1
Press [RDS].
2
While “RDS” is flashing
Press [TUNING, PTY SELECTOR,
2
,
1
] to select the program type.
3
While the PTY display is flashing
Press [BAND, EON].
“EON” lights.
The current station remains tuned in until the program type starts, then the unit switches to the station and “OTHER
PROGRAM SERVICE” scrolls across the display. (It changes immediately if the selected program is broadcasting.)
To cancel EON tuning
1. Press [RDS].
2. Press [BAND, EON].
EON tuning is also canceled if you operate the tuner, change the input source, or turn the unit off.
RDS
EON
B
PTY displays
NEWS
AFFAIRS
INFO
SPORT
EDUCATE
DRAMA
CULTURE
SCIENCE
VARIED
POP M
ROCK M
M. O. R. M
LIGHT M
CLASSICS
OTHER M
WEATHER
FINANCE
CHILDREN
SOCIAL A
RELIGION
PHONE IN
TRAVEL
LEISURE
JAZZ
COUNTRY
NATIONAL
OLDIES
FOLK M
DOCUMENT
TEST
ALARM
News
Current affairs
Information
Sport
Education
Drama
Culture
Science
Varied
Pop music
Rock music
Middle-of-the-road Music
Light classical
Serious classical
Other music
Weather information
Finance
Children
Social affairs
Religion
Phone in
Travel
Leisure
Jazz music
Country music
National music
Oldies
Folk music
Documentary
Test broadcast
Emergency announcement
25
RQT5802
26
RQT5802
A
1
2
VCR 1
VCR 2
B
TAPE MONITOR
TAPE MONITOR
INPUT SELECTOR
1 2
Making a recording
Note
¡ You cannot record a source connected through a digital terminal.
When recording CD, DVD, or TV, ensure the source is connected through the corresponding analogue terminals ( \ pages 6–7) and “ANALOG” input is selected ( \ page 18).
¡ When you select DVD 6CH INPUT mode, only sound from the front left and right channels is recorded.
A
Recording on a tape or MD deck, or VCR
You can record to a tape deck connected to TAPE/MD (or TAPE)
REC (OUT) or to a VCR connected to VCR 1 (or VCR) OUT.
See the recording unit’s operating instructions for details on how to prepare it for recording.
When recording with a tape or MD deck, you can record any source except TAPE/MD (or TAPE).
When recording with a VCR, you can record any source except
TAPE/MD (or TAPE) or VCR 1/2 (or VCR).
1
Turn [INPUT SELECTOR] to select the source to be recorded.
2
SA-DX1050 only
If you selected “VCR 1” in step 1, set
[VCR 1
l
, VCR 2
k
] to the required position.
3
Begin recording.
Follow your recording unit’s operating instructions.
4
Begin the source to be recorded.
Follow your equipment’s operating instructions.
B To monitor sound being recorded onto a tape deck
It is possible to check the sound being recorded if your tape deck is a 3 head system.
Press [TAPE MONITOR] on this unit and set the monitor button on the tape deck to
“TAPE”.
Press [TAPE MONITOR] once again to turn it off.
WAKE
1
-MODE
–TIME
TIMER
2
TIMER
-MODE
–TIME
3
For Europe
3 12
WAKE
For Australia and New Zealand
3 12
SLEEP
WAKE
WAKE
WAKE
MHz
Timer function
There are two timer functions: the sleep timer and the wake timer.
Note
¡ Sleep timer:
The unit turns off after a set time.
It can be set for 30, 60, or 90 minutes.
¡ Wake timer:
The unit can be set to turn on a certain number of hours after it is turned off.
It can be set for 5, 7, or 9 hours.
Setting the timers
1
Press [TIMER, -MODE, –TIME] to select the desired timer mode.
2
[Within 5 seconds]
Press [TIMER, -MODE, –TIME] and release when the time you require is displayed.
The display changes as follows:
¡ In sleep timer mode
30 / 60 / 90 (minutes)
↑
¡ In wake timer mode
5H / 7H / 9H (hours)
↑
The display is restored 5 seconds after the setting is completed.
3
Wake timer mode only
Press [
8
] to turn off the unit.
The “WAKE” indicator lights up.
Checking the remaining time on the sleep timer and the time set for the wake timer
Press [TIMER, -MODE, –TIME] once.
Note
Do not press [TIMER, -MODE, –TIME] again before the remaining time indication goes out.
The setting may change if you do this.
Changing a setting
Repeat steps 1 and 2.
To cancel the timer
Press [TIMER, -MODE, –TIME] until “OFF” is displayed.
“SLEEP” or “WAKE” will go out.
Note
¡ The timers cannot be used together.
¡ The sleep timer turns off the receiver, and the wake timer turns on the receiver, but they do not turn off/on any externally connected components.
27
RQT5802
28
RQT5802
-HELP
–RESET
The HELP function
If you make a mistake in operation or if sound output stops, the
HELP function displays information that indicates how you can remedy the situation.
If “ERROR” or scrolling characters (“SPEAKER OFF NOW”, for example) appear on the display, do the following.
Press [-HELP, –RESET].
The remedy for the situation is displayed.
For your reference
You can reset the unit’s settings to the factory settings. If this is ever necessary, press and hold [-HELP, –RESET] for about 2 seconds until “RESET” is displayed.
This will not erase radio stations you have preset
Maintenance
If the surfaces are dirty
To clean this unit, wipe with a soft, dry cloth.
If the surfaces are extremely dirty, use a soft cloth dipped in a soapand-water solution or a weak detergent solution.
¡ Never use alcohol, paint thinner or benzine to clean this unit.
¡ Before using chemically treated cloth, read the instructions that came with the cloth carefully.
Troubleshooting guide
Before requesting service, make the below checks. If you can’t fix the system as described below, or if something not listed here occurs, refer to the enclosed directory to locate an Authorized Service Center convenient to you or contact your dealer.
Common problems Ref.Pages
No power.
No sound.
Cannot select “DIGITAL” input.
Sound stops. “OVERLOAD” appears on the display.
“F 70” appears on the display.
The picture doesn’t appear on the television.
¡ Ensure the AC mains lead is connected.
¡ Turn the volume up.
¡ Turn muting off.
¡ Check connections to speakers and other equipment.
¡ Turn on the speakers.
¡ Turn off the tape monitor.
¡ Select the correct source.
¡ Change the DIGITAL input setting to suit the type of connection you have made.
¡ Check that the digital signals can be decoded by this unit.
¡ Turn PCM FIX or DTS FIX off.
¡ Cancel “DSP DEFEAT”.
¡ Switch off the unit, determine and correct the cause, then switch the unit on.
Causes include shorting of the positive and negative speaker wires, using speakers with an impedance lower than rated for this unit, straining of the speakers through excessive volume or power, and using the unit in a hot environment.
¡ Use speakers with the right impedance rating.
¡ Turn the unit off, disconnect the AC mains lead, then reconnect and turn the unit on. Consult your dealer if “F 70” remains on the display.
¡ Change the television’s input mode to suit the connections between this unit and the television.
10–11
–
–
9
18
21
6–11
18
21
18
12–13
16
16
22
–
Sound is not heard from the center, surround, or subwoofer speakers.
DSP sound modes cannot be selected.
DSP sound modes
¡ Ensure the size settings for your speakers are correct.
¡ Check the DSP sound mode.
¡ Cancel “DSP DEFEAT”.
¡ Cancel “DSP DEFEAT”.
¡ Turn SPEAKERS B off.
¡ Turn DVD 6CH INPUT off.
Ref.Pages
12–13
16–17
22
22
19
19
The radio cannot be tuned in or there is a lot of noise and interference.
The correct AM frequency cannot be turned in.
Radio
¡ Adjust the position of the FM or AM antenna.
¡ Reduce the treble.
¡ Select “DSP DEFEAT”.
¡ Turn off nearby televisions, video decks, DVD players, and satellite receivers.
¡ You may need an outdoor antenna or an antenna with more elements.
¡ Separate the antenna from other cables, leads, and appliances.
¡ Change the frequency step. Hold [BAND] down for 10 seconds to change the step to 9 kHz.
Ref.Pages
8–9
20
22
22
8–9
–
22
29
RQT5802
30
RQT5802
Specifications
(DIN 45 500)
■ AMPLIFIER SECTION
Power output (at 230 V for Continental Europe)
(at 240 V for the United Kingdom, Australia and
New Zealand)
DIN 1 kHz (T.H.D. 1 %) 2 x 100 W (6
Ω
)
[SA-DX1050]
20 Hz–20 kHz continuous power output both channels driven
[SA-DX950]
2 x 80 W (6
Ω
)
40 Hz–20 kHz continuous power output both channels driven 2 x 80 W (6
Ω
)
Total harmonic distortion
[SA-DX1050] rated power at 20 Hz–20 kHz
[SA-DX950] rated power at 40 Hz–20 kHz half power at 1 kHz
0.09 % (6
Ω
)
0.09 % (6
Ω
)
0.03 % (6
Ω
)
Power output at 1 kHz each channel driven
DIN 1 kHz (T.H.D. 1 %)
Front
Center
2 x 100 W (6
Ω
)
100 W (6
Ω
)
2 x 100 W (6
Ω
) Surround
Power bandwidth both channels driven, –3 dB
Damping factor
10 Hz–70 kHz (6
Ω
, 0.9 %)
30 (6
Ω
)
Load impedance
Front
A or B
A and B
Center
Surround
4–16
Ω
8–16
Ω
6–16
Ω
6–16
Ω
Frequency response
PHONO RIAA standard curve (30 Hz–15 kHz) ±0.8 dB
[SA-DX1050] CD, TAPE/MD, DVD, TV, VCR 1, VCR 2
10 Hz–40 kHz, ±3 dB
[SA-DX950 for Europe]
CD, TAPE/MD, DVD, TV, VCR 10 Hz–40 kHz, ±3 dB
[SA-DX950 for Australia and New Zealand]
CD, TAPE, DVD, TV, VCR 10 Hz–40 kHz, ±3 dB
Input sensitivity and impeadance
PHONO 3 mV/47 k
Ω
[SA-DX1050] CD, TAPE/MD, DVD, TV, VCR 1, VCR 2
200 mV/22 k
Ω
[SA-DX950 for Europe]
CD, TAPE/MD, DVD, TV, VCR 200 mV/22 k
Ω
[SA-DX950 for Australia and New Zealand]
200 mV/22 k
Ω
CD, TAPE, DVD, TV, VCR
S/N at rated power (6
Ω
)
PHONO 70 dB (IHF, A: 80 dB)
[SA-DX1050] CD, TAPE/MD, DVD, TV, VCR 1, VCR 2
75 dB (IHF, A: 85 dB)
[SA-DX950 for Europe]
CD, TAPE/MD, DVD, TV, VCR 75 dB (IHF, A: 85 dB)
[SA-DX950 for Australia and New Zealand]
CD, TAPE, DVD, TV, VCR
DVD 6CH
75 dB (IHF, A: 85 dB)
100 dB (IHF A, Rated Power, S=2 V), 75 dB (IHF, A: 85 dB)
Output voltage
[SA-DX1050] TAPE/MD REC (OUT), VCR 1 OUT
[SA-DX950 for Europe]
200 mV
200 mV TAPE/MD REC (OUT), VCR OUT
[SA-DX950 for Australia and New Zealand]
TAPE REC (OUT), VCR OUT
Tone controls
200 mV
BASS
TREBLE
Channel balance (250 Hz–6.3 kHz)
Channel separation
Headphones output level and impeadance
Subwoofer frequency response (–6 dB)
50 Hz, +10 to –10 dB
20 kHz, +10 to –10 dB
±1 dB
55 dB
430 mV/330
Ω
7–200 Hz
Digital input
Optical
Coaxicial
2
1
■ FM TUNER SECTION
Frequency range
Sensitivity
S/N 30 dB
S/N 26 dB
S/N 20 dB
IHF usable sensitivity (IHF’58)
IHF 46 dB stereo quieting sensitivity
Total harmonic distortion
MONO
STEREO
S/N
MONO
STEREO
Frequency response
20 Hz–15 kHz
Alternate channel selectivity
±400 kHz
Capture ratio
Image rejection at 98 MHz
IF rejection at 98 MHz
Spurious response rejection at 98 MHz
AM suppression
Stereo separation
1 kHz
Carrier leak
19 kHz
38 kHz
Channel balance (250 Hz–6.3 kHz)
Limiting point
Bandwidth
IF amplifier
FM demodulator
Antenna terminal
■ AM TUNER SECTION
Frequency range
Sensitivity
Selectivity (at 999 kHz)
IF rejection (at 999 kHz)
87.50–108.00 MHz
1.5 µV/75
Ω
1.3 µV/75
Ω
1.2 µV/75
Ω
1.5 µV/75
Ω
22 µV/75
Ω
0.2 %
0.3 %
60 dB (73 dB, IHF)
58 dB (67 dB, IHF)
+1 dB, –2 dB
65 dB
1.5 dB
40 dB
70 dB
70 dB
50 dB
40 dB
–30 dB (–35 dB, IHF)
–50 dB (–55 dB, IHF)
±1.5 dB
1.2 µV
180 kHz
1000 kHz
75
Ω
(unbalanced)
522–1611 kHz (9 kHz steps)
530–1620 kHz (10 kHz steps)
20 µV, 330 µV/m
55 dB
50 dB
■ VIDEO SECTION
Output voltage at 1 V input (unbalanced)
Maximum input voltage
Input/output impedance
1±0.1 Vp-p
1.5 Vp-p
75
Ω
(unbalanced)
■ GENERAL
Power supply
For Continental Europe AC 230 V, 50 Hz
For the United Kingdom, Australia and New Zealand
Power consumption
Dimensions (W x H x D)
AC 230–240 V, 50 Hz
230 W
Mass
430 x 158 x 375 mm
[SA-DX1050] 10.0 k g
[SA-DX950] 9.8 k g
Power consumption in standby mode: 2 W
Notes:
1. Specifications are subject to change without notice.
Mass and dimensions are approximate.
2. Total harmonic distortion is measured by the digital spectrum analyzer.
MEMO
31
RQT5802
WARNING:
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR
PRODUCT DAMAGE, DO NOT EXPOSE THIS APPLIANCE
TO RAIN, SPLASHING, DRIPPING OR MOISTURE.
CAUTION!
DO NOT INSTALL, OR PLACE THIS UNIT, IN A BOOKCASE,
BUILT-IN CABINET OR IN ANOTHER CONFINED SPACE.
ENSURE THE UNIT IS WELL VENTILATED. TO PREVENT
RISK OF ELECTRIC SHOCK OR FIRE HAZARD DUE TO
OVERHEATING, ENSURE THAT CURTAINS AND ANY
OTHER MATERIALS DO NOT OBSTRUCT THE
VENTILATION VENTS.
SUOMI
VAROITUS:
TULIPALO-, SÄHKÖISKUVAARAN TAI MUUN VAHINGON
VÄHENTÄMISEKSI EI LAITETTA SAA ALTISTAA
SATEELLE, ROISKEELLE, VESIPISAROILLE TAI
KOSTEUDELLE.
VAROITUS!
ÄLÄ ASENNA TAI LAITA TÄTÄ LAITETTA
KABINETTITYYPPISEEN KIRJAKAAPPIIN TAI MUUHUN
SULJETTUUN TILAAN, JOTTA TUULETUS ONNISTUISI.
VARMISTA, ETTÄ VERHO TAI MIKÄÄN MUU MATERIAALI
EI HUONONNA TUULETUSTA, JOTTA VÄLTETTÄISIIN
YLIKUUMENEMISESTA JOHTUVA SÄHKÖISKU- TAI
TULIPALOVAARA.
NORSK
ADVARSEL:
FOR Å REDUSERE FAREN FOR BRANN, STRØMSJOKK
ELLER SKADER PÅ PRODUKTET, MÅ DETTE APPARATET
IKKE UTSETTES FOR REGN, VANNSPRUT, VANNDRÅPER
ELLER FUKTIGHET.
ADVARSEL!
APPARATET MÅ IKKE PLASSERES I EN BOKHYLLE, ET
INNEBYGGET KABINETT ELLER ET ANNET LUKKET STED
HVOR VENTILASJONSFORHOLDENE ER
UTILSTREKKELIGE. SØRG FOR AT GARDINER ELLER
LIGNENDE IKKE FORVERRER
VENTILASJONSFORHOLDENE, SÅ RISIKO FOR
ELEKTRISK SJOKK ELLER BRANN FORÅRSAKET AV
OVERHETING UNNGÅS.
Matsushita Electric Industrial Co., Ltd.
Osaka 542-8588, Japan
En
RQT5802-B
H0101HM0
Advertisement