Technics SA-DX940 Stereo System User Manual

Add to my manuals
79 Pages

advertisement

Technics SA-DX940 Stereo System User Manual | Manualzz

Printed in Malaysia

3-452-777-12(1)

Operating Instructions

Blu-ray Disc / DVD Player

BDP-BX1

© 2008 Sony Corporation

3-452-777-12(1)

2

WARNING

To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.

To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only.

Batteries or batteries installed apparatus shall not be exposed to excessive heat such as sunshine, fire or the like.

CAUTION

The use of optical instruments with this product will increase eye hazard. As the laser beam used in this Blu-ray Disc/DVD player is harmful to eyes, do not attempt to disassemble the cabinet.

Refer servicing to qualified personnel only.

This label is located on the laser protective housing inside the enclosure.

This symbol is intended to alert the user to the presence of uninsulated

“dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

CAUTION

You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment.

The shielded Interface cable

(Network cable) must be used with the equipment in order to comply with the limits for a digital device pursuant to Subpart B of Part 15 of

FCC Rules.

b

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

– Reorient or relocate the receiving antenna.

– Increase the separation between the equipment and receiver.

– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

– Consult the dealer or an experienced radio/TV technician for help.

Precautions

• To prevent fire or shock hazard, do not place objects filled with liquids, such as vases, on the apparatus.

• Install this unit so that the AC power cord can be unplugged from the wall socket immediately in the event of trouble.

Owner’s Record

The model and serial numbers are located at the rear of the unit.

Record the serial number in the space provided below. Refer to them whenever you call upon your

Sony dealer regarding this product.

Model No. BDP-BX1

Serial No.______________

For customers in the U.S.A

If this product is not working properly, please call 1-800-222-

7669.

For Customers in Canada

If this product is not working properly, please call 1-877-602-

2008 for Peace of Mind

Warranty Replacement service.

For other product related questions please contact our Customer

Information Service Center at

1-877-899-7669 or write to us at:

Customer Information Service 115

Gordon Baker Road, Toronto,

Ontario, M2H 3R6

Notes About the Discs

• To keep the disc clean, handle the disc by its edge. Do not touch the surface.

Dust, fingerprints, or scratches on the disc may cause it to malfunction.

• Do not expose the disc to direct sunlight or heat sources such as hot air ducts, or leave it in a car parked in direct sunlight as the temperature may rise considerably inside the car.

• After playing, store the disc in its case.

• Clean the disc with a cleaning cloth. Wipe the disc from the center out.

• Do not use solvents such as benzine, thinner, commercially available disc/ lens cleaners, or anti-static spray intended for vinyl LPs.

• If you have printed the disc’s label, dry the label before playing.

• Do not use the following discs.

– A disc that has a nonstandard shape (e.g., card, heart).

– A disc with a label or sticker on it.

– A disc that has cellophane tape or sticker adhesive on it.

• Do not resurface the playing side of a disc to remove surface scratches.

Precautions

On safety

• To prevent fire or shock hazard, do not place objects filled with liquids, such as vases, on the player, or place the player near water, such as near a bathtub or shower room.

Should any solid object or liquid fall into the cabinet, unplug the player and have it checked by qualified personnel before operating it any further.

• Do not touch the AC power cord with wet hands. Doing so may cause an electric shock.

On placement

• Place the player in a location with adequate ventilation to prevent heat build-up in the player.

• Do not place the player on a soft surface such as a rug that might block the ventilation holes.

• Do not install this player in a confined space, such as a bookshelf or similar unit.

• Do not place the player in a location near heat sources, or in a place subject to direct sunlight, excessive dust, or mechanical shock.

• If the player is brought directly from a cold to a warm location, or is placed in a very damp room, moisture may condense on the lenses inside the player.

Should this occur, the player may not operate properly. In this case, remove the disc and leave the player turned on for about half an hour until the moisture evaporates.

• Do not install the player in an inclined position. It is designed to be operated in a horizontal position only.

• Keep the player and the discs away from equipment with strong magnets, such as microwave ovens, or large loudspeakers.

• Do not place heavy or unstable objects on the player.

• Do not place any objects other than discs on the disc tray.

Doing so may cause damage to the player or the object.

• When you move the player, take out any discs. If you don’t, the disc may be damaged.

• When you move the player, disconnect the AC power cord and all other cables from the player.

On power sources

• The player is not disconnected from the AC power source as long as it is connected to the wall outlet, even if the player itself has been turned off.

• If you are not going to use the player for a long time, be sure to disconnect the player from the wall outlet. To disconnect the AC power cord, grasp the plug itself; never pull the cord.

• Observe following points to prevent the AC power cord being damaged. If the AC power cord is damaged, it may result in a fire or an electric shock.

– Do not pinch the AC power cord between the player and wall, shelf, etc.

– Do not put anything heavy on the AC power cord or pull on the AC power cord itself.

On adjusting volume

Do not turn up the volume while listening to a section with very low level inputs or no audio signals. If you do, the speakers may be damaged when a peak level section is played.

On cleaning

Clean the cabinet, panel, and controls with a soft cloth slightly moistened with a mild detergent solution. Do not use any type of abrasive pad, scouring powder or solvent such as alcohol or benzine.

,continued

3

4

On cleaning discs, disc/ lens cleaners

Do not use cleaning discs or disc/lens cleaners (including wet or spray types). These may cause the apparatus to malfunction.

On replacement of parts

In the events that this player is repaired, repaired parts may be collected for reuse or recycling purposes.

Copyrights and

Trademarks

• This product incorporates copyright protection technology that is protected by

U.S. patents and other intellectual property rights.

Use of this copyright protection technology must be authorized by Macrovision, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision.

Reverse engineering or disassembly is prohibited.

• “AVCHD” and the “AVCHD” logo are trademarks of

Matsushita Electric Industrial

Co., Ltd. and Sony

Corporation.

• Java and all Java-based trademarks and logos are trademarks or registered trademarks of Sun

Microsystems, Inc.

• , “XMB,” and “xross media bar” are trademarks of Sony

Corporation and Sony

Computer Entertainment Inc.

• This Blu-ray Disc/DVD player incorporates High-Definition

Multimedia Interface

(HDMI™) technology.

HDMI, the HDMI logo and

High-Definition Multimedia

Interface are trademarks or registered trademarks of

HDMI Licensing LLC.

• “Blu-ray Disc” is a trademark.

• “Blu-ray Disc,” “DVD+RW,”

“DVD-RW,” “DVD+R,”

“DVD-R,” “DVD VIDEO,” and “CD” logos are trademarks.

• “x.v.Color” and “x.v.Color” logo are trademarks of Sony

Corporation.

• “BRAVIA Sync” is a trademark of Sony

Corporation.

• “PhotoTV HD” and the

“PhotoTV HD” logo are trademarks of Sony

Corporation.

• Other system and product names are generally trademarks or registered trademarks of the manufacturers. ™ and ® marks are not indicated in this document.

IMPORTANT NOTICE

Caution: This player is capable of holding a still video image or on-screen display image on your television screen indefinitely. If you leave the still video image or onscreen display image displayed on your TV for an extended period of time you risk permanent damage to your television screen.

Plasma display panel televisions and projection televisions are susceptible to this.

If you have any questions or problems concerning your player, please consult your nearest Sony dealer.

Important Safety

Instructions

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other.

A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10)Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11)Only use attachments/ accessories specified by the manufacturer.

12)Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus.

When a cart is used, use caution when moving the cart/ apparatus combination to avoid injury from tip-over.

13)Unplug this apparatus during lightning storms or when unused for long periods of time.

14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

About this manual

• In this manual, “disc” is used as a general reference for the

BDs, DVDs, or CDs unless otherwise specified by the text or illustrations.

• Icons, such as

BD

, listed at the top of each explanation indicate what kind of media can be used with the function being explained.

For details, see “Playable

Discs” (page 59).

• Instructions in this manual describe the controls on the remote. You can also use the controls on the player if they have the similar symbols as those on the remote.

• The on-screen display illustrations used in this manual may not match the graphics displayed on your TV screen.

• NEED-to-know information

(to prevent incorrect operation) is listed under the b icon. NICE-to-know information (tips and other useful information) is listed under the z icon.

5

6

Table of Contents

WARNING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Guide to Parts and Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Hookups and Settings

Hooking Up the Player . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Step 1: Connecting to Your TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Connecting to an HDMI jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

About the BRAVIA Sync features (for HDMI connections only) . . . . . . 16

Connecting to component video jacks (Y, P b

, P r

) . . . . . . . . . . . . . . . . . 17

Connecting to an audio/video or S VIDEO jack . . . . . . . . . . . . . . . . . . 18

Step 2: Connecting to Your AV Amplifier (Receiver) . . . . . . . . . . . . . . . . . . . 19

Connecting to an HDMI jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Connecting to digital jacks (OPTICAL/COAXIAL) . . . . . . . . . . . . . . . . . 21

Connecting to audio L/R jacks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Step 3: Inserting the External Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Step 4: Connecting to the Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

When connecting to a broadband router directly . . . . . . . . . . . . . . . . . 24

When connecting via a wireless LAN router . . . . . . . . . . . . . . . . . . . . . 25

Step 5: Connecting the AC Power Cord . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Step 6: Preparing the Remote . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Controlling TVs with the remote . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Step 7: Easy Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Playback

Playing BDs/DVDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Using the BD’s or DVD’s menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Enjoying BonusView . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Searching for a scene quickly (Scene Search) . . . . . . . . . . . . . . . . . . . 34

Searching for a Title/Chapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Displaying the playing time and play information . . . . . . . . . . . . . . . . . 35

Adjusting pictures and sound for videos . . . . . . . . . . . . . . . . . . . . . . . . 35

Playing CDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Playing Photo Files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Settings and Adjustments

Using the Settings Displays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Network Update . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Video Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Audio Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

BD/DVD Viewing Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Photo Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

System Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Network Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Easy Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

Resetting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

Additional Information

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Self-Diagnosis Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

Playable Discs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

Video Output Resolution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

Audio Output Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

Language Code List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

Parental Control/Area Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

Terms and Conditions of Use and End User License Agreement . . . . . . . . . 66

Software License Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79

Before operating the player, please read “Terms and Conditions of Use and End User License

Agreement” (page 66).

7

8

Guide to Parts and

Controls

For more information, see the pages in parentheses.

Remote

Number 5, AUDIO, CH +, and N PLAY buttons have a tactile dot. Use the tactile dot as a reference when operating the player.

A Z OPEN/CLOSE (page 31)

Opens or closes the disc tray.

THEATER (page 16)

Switches to the optimum video mode for watching movies automatically. When connected with an AV amplifier

(receiver) using the HDMI cable, the speaker output also switches automatically. Press the button again to return to the original setting.

When connected with a Theater Modecompatible TV using the HDMI cable, the TV’s video mode switches to Theater

Mode.

b

The THEATER button functions only when connected to a Theater Mode-compatible TV.

TV [/1 (on/standby) (page 26)

Turns on the TV, or sets to standby mode.

[/1 (on/standby) (page 28)

Turns on the player, or sets to standby mode.

B Number buttons (page 34, 52)

Enters the title/chapter numbers, etc.

CLEAR

Clears the entry field.

C TIME (page 11)

Displays the elapsed/remaining playback time in the front panel display. Each time you press the button, the display switches between elapsed playback time and remaining playback time.

AUDIO (page 47)

Selects the language track when multilingual tracks are recorded on BD-

ROMs/DVD VIDEOs.

Selects the sound track on CDs.

SUBTITLE (page 47)

Selects the subtitle language when multilingual subtitles are recorded on BD-

ROMs/DVD VIDEOs.

ANGLE

Switches to other viewing angles when multi-angles are recorded on BD-ROMs/

DVD VIDEOs.

DISPLAY (page 35)

Displays the playback information on the screen.

D Color buttons (RED/GREEN/

BLUE/YELLOW)

Short cut keys for selecting items on some BD’s menus (can also be used for

BD’s Java interactive operations).

E TOP MENU (page 33)

Opens or closes the BD’s or DVD’s Top

Menu.

POP UP/MENU (page 33)

Opens or closes the BD-ROM’s Pop-up

Menu, or the DVD’s menu.

OPTIONS (page 33, 38)

The options menu that can be selected appears on the screen.

HOME (page 40)

Enters or exits the player’s home menu.

RETURN

Returns to the previous display.

</M/m/,

Moves the highlight to select a displayed item.

Center button (ENTER)

Enters the selected item.

F . PREV/NEXT > (previous/

next)

Skips to the previous/next chapter, track, or file.

To go to the beginning of the previous track, press . PREV twice.

REPLAY/ADVANCE

(instant replay/instant advance)

Replays the scene/briefly fast forwards the scene.

m/M

(fast reverse/fast forward)

Fast reverses/fast forwards the disc when pressed during playback.

Each time you press the button, search speed changes as follows*:

Playback direction

M1 (×10) t M2 (×30) t M3

(×120)

Reverse direction n1 (×1) t m1 (×10) t m2 (×30) t m3 (×120)

When you press and hold the button, fast forward/fast reverse continues at the selected speed until you release the button.

* Search speed does not change when playing

CDs.

Speed multiple values are approximate.

– To resume normal playback, press

N PLAY.

N PLAY (page 31)

Starts or re-starts playback.

Resumes playback from the point where you press x STOP (Resume Play).

Plays a slideshow when a disc containing

JPEG image files is inserted.

SCENE SEARCH (page 34)

Switches to Scene Search mode that lets you move quickly between scenes within the title currently being played back.

X PAUSE

Pauses or re-starts playback.

x STOP

Stops playback and remembers the stop

point (resume point) (page 32, 37).

The resume point for a title/track is the last point you played or the last photo for a photo folder.

G For TVs operable with the following

buttons, see page 26.

MUTING

Mutes the TV sound.

VOL (volume) +/–

Adjusts the TV volume.

CH (channel) +/–

Selects the TV channels up and down.

INPUT (input select)

Switches between TV and other input sources.

LIGHT

Lights up the 5 and 6 buttons (except

</M/m/, and ENTER) and is useful for operation in the dark.

,continued

9

10

Front panel

A [/1 (on/standby) (page 28)

Turns on the player, or sets to standby mode.

B Disc tray (page 31)

C Blu-ray Disc indicator

Lights up when a BD is recognized.

z

When the player is turned on for the first time, the Blu-ray Disc indicator lights up, then turns off when Easy Setup is complete.

D Front panel display (page 11)

E Remote sensor (page 26)

F 24P indicator (page 44)

Lights up when outputting 1080p/24 Hz video signals of BD-ROMs.

G N (play), X (pause), x (stop)

(page 31)

Starts, pauses, or stops playback.

H A (open/close) (page 31)

Opens or closes the disc tray.

To lock the disc tray (Child Lock)

You can lock the disc tray to prevent it being opened by mistake.

When the player is turned on, hold down X on the player for more than 10 seconds until

“LOCKED” appears in the front panel display. The disc tray is locked.

To unlock the disc tray, hold down X on the player until “UNLOCK” appears in the front panel display.

Front panel display

A N, X

Lights up during playback or pause.

B HD (page 43)

Lights up when outputting 720p/1080i/

1080p video signals from the HDMI

OUT jack or 720p/1080i video signals from the COMPONENT VIDEO OUT jacks.

C HDMI (page 16)

Lights up when an HDMI device is connected.

D EXT (page 23)

Lights up when the external memory is recognized.

E Playback information

You can check the time information.

Press TIME repeatedly during playback.

The display changes as follows.

When playing a BD-ROM/DVD VIDEO

Elapsed time of the current title r

Remaining time of the current title

When playing a CD

Elapsed time of the current track r

Remaining time of the current track r

Elapsed time of the current disc r

Remaining time of the current disc z

“T” (Title or Track), “C” (Chapter), or “D”

(Disc) may be displayed depending on the disc.

F Network connection indicator

Lights up when downloading the player’s software.

For details on downloading the player’s

software, see page 41.

,continued

11

12

Rear panel

A COMPONENT VIDEO OUT

(Y, P

B

, P

R

) jacks (page 17)

B LINE OUT (S VIDEO) jack

(page 18)

C LINE OUT (R-AUDIO-L) jacks

(page 18, 22)

D AC IN terminal (page 25)

E Ventilation holes

The ventilation fan is inside the player.

F EXT slot (page 23)

G DIGITAL OUT (OPTICAL/

COAXIAL) jacks (page 21)

H LINE OUT (VIDEO) jack (page 18)

I HDMI OUT jack (page 15, 20)

J LAN (100) terminal (page 24)

Hookups and

Settings

Hooking Up the Player

Check that you have the following items.

• Audio/video cable (phono plug ×3) (1)

• AC power cord (1)

• HDMI cable (1)

• Remote commander (remote) (1)

• Size AA (R6) batteries (2)

Follow steps 1 through 7 to hook up and adjust the settings of the player. Do not connect the AC power cord until you reach

“Step 5: Connecting the AC Power Cord”

(page 25).

13

14

Step 1: Connecting to Your TV

About video/HDMI OUT jacks

The player has the following video jacks. Connect the player to your TV according to the input jack on your TV.

When connecting the player to your TV using the HDMI cable, you can enjoy high quality digital pictures and sound through the HDMI OUT jack.

Jack type

High quality

Digital

Analog

Video resolution Hookup

High Definition:

1080/24p, 1080p,

1080i, 720p

Standard Definition:

480p, 480i

See “Connecting to an

HDMI jack” (page 15).

High Definition:

1080i, 720p

Standard Definition:

480p, 480i

See “Connecting to component video jacks

(Y, Pb, Pr)” (page 17).

Standard Definition:

480i

See “Connecting to an audio/video or S

VIDEO jack”

(page 18).

Standard Definition:

480i

See “Connecting to an audio/video or S

VIDEO jack”

(page 18).

Standard quality

b

• Plug in cables securely to prevent unwanted noise.

• Refer to the instructions supplied with the components to be connected.

• You cannot connect this player to a TV that does not have a video input jack.

• Do not apply too much pressure on the connecting cables. Pushing against the cabinet wall, etc., may damage the cable.

To connect to a TV with DVI input

Use an HDMI-DVI converter cable (not supplied). The DVI jack will not accept any audio signals, so you have to use another audio connection in addition to this

connection (page 19).

Furthermore, you cannot connect the HDMI

OUT jack to DVI jacks that are not HDCP compliant (e.g., DVI jacks on PC displays).

Connecting to an HDMI jack

Connect the player and your TV using an HDMI cable to enjoy high quality digital pictures and sound through the HDMI OUT jack.

If you connect a Sony TV that is compatible with the “Control for HDMI” function (page 16),

refer to the operating instructions supplied with the TV.

If you connect a 1080/24p- or 1080p-compatible TV, use a High Speed HDMI cable.

Blu-ray Disc/DVD player

HDMI cable (supplied)

TV

Notes on connecting to the HDMI OUT jack

Observe the following as improper handling may damage the HDMI OUT jack and the connector.

• Carefully align the HDMI OUT jack on the rear of the player and the HDMI connector by checking their shapes. Make sure the connector is not upside down or tilted.

• Be sure to disconnect the HDMI cable when moving the player.

• If you place the player on a cabinet with the

HDMI cable connected, do not apply too much pressure to the cabinet wall. It may damage the HDMI OUT jack or the HDMI cable.

• When connecting or disconnecting, do not screw in or rotate the HDMI connector.

,continued

15

16

About indicators for HDMI connection

When connecting an HDMI compatible component, the HDMI indicator lights up in the front panel display.

b

• Consumers should note that not all high definition television sets are fully compatible with this product and may cause artifacts to be displayed in the picture. In the case of 480p/720p/1080i/1080p scan picture problems, it is recommended that the user switch the connection to the ‘standard definition’ output. If there are questions regarding our TV set compatibility with this model 480p/

720p/1080i/1080p Blu-ray Disc/DVD player, please contact our customer service center.

• If the picture is not clear, not natural or not to your satisfaction, change the video output resolution in

step 3 of “Output Video Format” under the

“Video Settings” setup (page 43).

• Be sure to use only an HDMI cable that bears the

HDMI logo.

About the BRAVIA Sync features (for HDMI connections only)

By connecting Sony components that are compatible with the “Control for HDMI” function with an HDMI cable (supplied), operation is simplified as below:

• One-Touch Play

With one touch of the following buttons, the connected TV turns on and the input selector on the TV is switched to the player automatically.

– [/1

– HOME: The home menu appears

automatically (page 40).

– N PLAY: Playback starts automatically

(page 32).

• System Power-Off

When you turn off the TV using the power button on the TV’s remote, the player and

HDMI-compatible components turn off automatically.

• Theater

When you press THEATER, the player automatically switches to the optimum video mode for watching movies. When connected with an AV amplifier (receiver) using the HDMI cable, the speaker output also switches automatically. When connected with a Theater Mode-compatible

TV using the HDMI cable, the TV’s video mode switches to Theater Mode. Press the button again to return to the original setting.

• Language Follow

When you change the language for the onscreen display on your TV, the player’s language for the on-screen display is also changed after turning the player off and on.

To prepare for the BRAVIA Sync features

Set “Control for HDMI” to “On” in the

“System Settings” setup (page 50).

For details on settings of your TV or other connected components, refer to the operating instructions supplied with the TV or components.

z

• When connecting the Sony TV that is compatible with the “Control for HDMI” Easy Setting function using the HDMI cable, the “Control for

HDMI” setting of the player automatically switches to “On” if the “Control for HDMI” setting on the connected TV is set to “On.” Refer to the operating instructions supplied with the

TV.

• When connecting the Sony TV that is compatible with the BRAVIA Sync features using the HDMI cable, you can control the basic functions of the player with the TV’s remote if the “Control for

HDMI” setting on the connected TV is set to

“On.” Refer to the operating instructions supplied with the TV.

b

Depending on the connected component, the

“Control for HDMI” function may not work. Refer to the operating instructions supplied with the component.

Connecting to component video jacks (Y, P

B

, P

R

)

Connect the COMPONENT VIDEO OUT jacks of the player and your TV using a component video cable or three video cables (not supplied) of the same kind and length. You can enjoy high-quality pictures.

Be sure to connect to the LINE OUT (R-AUDIO-L) jacks using the audio/video cable.

Blu-ray Disc/DVD player

(green) (blue) (red) (red) (white)

Component video cable (not supplied)

Audio/video cable

(supplied)

(green) (blue) (red) (red) (white)

Match the color of the plug to that of the jack.

: Signal flow

b

When you connect the player and TV using a component video cable, disconnect the video plug

(yellow) of the audio/video cable.

TV

Match the color of the plug to that of the jack.

,continued

17

Connecting to an audio/video or S VIDEO jack

Connect the LINE OUT (VIDEO, R-AUDIO-L) jacks of the player and your TV using the audio/video cable. You can enjoy standard quality pictures and sound.

Blu-ray Disc/DVD player

S-video cable

(not supplied) or

(yellow) (red) (white)

Audio/video cable

(supplied)

(yellow) (red) (white)

Match the color of the plug to that of the jack.

18

: Signal flow

b

When you connect the player and TV using an Svideo cable, disconnect the video plug (yellow) of the audio/video cable.

TV

Step 2: Connecting to Your AV Amplifier (Receiver)

About audio/HDMI OUT jacks

The player has the following audio jacks. Connect the player to your AV amplifier (receiver) according to the input jack on your AV amplifier (receiver).

Jack type

Digital

Hookup

See “Connecting to an HDMI jack” (page 20).

Analog

See “Connecting to digital jacks (OPTICAL/

COAXIAL)” (page 21).

See “Connecting to audio L/R jacks” (page 22).

z

For correct speaker location, refer to the operating instructions supplied with the connected components.

b

• When you connect the player to your AV amplifier (receiver) using an HDMI cable, do one of the following:

– Connect your AV amplifier (receiver) to your

TV using an HDMI cable, or

– Connect the player to your TV using a video cable other than an HDMI cable (component video cable, S-video cable, or audio/video cable).

• If you connect a component that does not conform to the selected audio signal, a loud noise (or no sound) will come from the speakers, which could damage your ears or the speakers.

,continued

19

Connecting to an HDMI jack

If your AV amplifier (receiver) has an HDMI input, you can enjoy surround sound.

If you connect a Sony AV amplifier (receiver) that is compatible with the “Control for HDMI”

function (page 16), refer to the operating instructions supplied with the AV amplifier (receiver).

Blu-ray Disc/DVD player

HDMI cable (supplied)

AV amplifier (receiver)

HDMI cable (not supplied)

TV

20

z

Set the following settings and you can enjoy higher quality sound from the connected AV amplifier

(receiver).

– Set “Audio Output Priority” to “HDMI” in the

“Audio Settings” setup (page 45).

– Set “Audio (HDMI)” to “Auto” in the “Audio

Settings” setup (page 45).

– Set “BD Audio Setting” to “Direct” in the “Audio

Settings” setup (page 45).

b

Not all HDMI-compatible AV amplifiers

(receivers) accept 8ch Linear PCM signals. Refer as well to instructions supplied with the connected AV amplifier (receiver).

Connecting to digital jacks (OPTICAL/COAXIAL)

If your AV amplifier (receiver) has a Dolby

*1

Digital, Dolby Pro Logic, or DTS

*2

decoder and a digital input jack, you can enjoy Dolby Digital (5.1ch), Dolby Pro Logic (4.0ch), or DTS

(5.1ch) surround effects.

Blu-ray Disc/DVD player

Optical digital cable

(not supplied) or

Coaxial digital cable

(not supplied)

: Signal flow

1

Connect the digital jack of the player and your AV amplifier (receiver).

2

Set “Audio Output Priority” to

“Coaxial/Optical” in the “Audio

Settings” setup (page 45).

3

Make the appropriate settings in

“Dolby Digital” and “DTS” under the

“Audio Settings” setup (page 46).

Otherwise, no sound or a loud noise will come from your speakers.

*1

*2

AV amplifier (receiver)

,continued

21

22

Connecting to audio L/R jacks

If your AV amplifier (receiver) only has L and R audio input jacks, use this connection.

Blu-ray Disc/DVD player

: Signal flow

(red) (white)

Audio/video cable (supplied)

(red) (white)

Match the color of the plug to that of the jack.

AV amplifier (receiver)

Step 3: Inserting the

External Memory

To enjoy additional content (such as

BonusView) on certain Blu-ray Disc titles, you will need to use external memory.

Insert the external memory device (1 GB or larger USB flash memory, such as Sony

USM1GH) into the EXT slot as your local storage.

Insert the external memory in the V

direction into the EXT slot as far as it will go.

Check that the EXT indicator lights up in the front panel display when turning the player on.

Rear of the player

Sony USM1GH

(not supplied)

With the terminal side up

b

• Do not connect anything other than a USB flash memory, such as an HDD, etc., to the EXT slot.

• Insert the external memory straight. If you force the external memory into the slot, this will cause damage to both the external memory and the player.

• Keep the external memory away from small children to prevent them from accidentally swallowing the external memory.

• Do not apply too much pressure to the external memory in the slot, as it may cause a malfunction.

• We recommend use of the Sony USM1GH available as of April 2008.

• Other USB flash devices may support this function. However we cannot guarantee compatibility with all USB flash memories.

• When inserting a USB flash memory other than

Sony USM1GH, check the insertion direction before inserting it.

• Depending on the USB flash memory, it may stick out from the EXT slot. Do not force into the slot or apply pressure to the protruding portion of the USB flash memory.

• To avoid data corruption or damage to the external memory, turn the player off when inserting or removing the external memory.

• When the EXT indicator does not light up, turn the player off, remove and re-insert the external memory, then turn the player on again.

• Do not insert the external memory that contains photo or music files to avoid corrupting the external memory data.

To enjoy BonusView

See “Enjoying BonusView” (page 33).

To remove the external memory

1

Press [/1 to turn the player off.

2

Pull out the external memory from the

EXT slot.

23

24

Step 4: Connecting to the Network

Connect the LAN (100) terminal of the player to your Internet source using a network cable to update the player’s software using the network.

1

Connect the LAN (100) terminal of the player to your Internet source.

Methods to connect to your Internet source include:

• Connecting to a broadband router directly

• Connecting via a wireless LAN router

Refer also to the instructions supplied with the broadband router or the wireless

LAN router.

2

Make the appropriate settings in

“Internet Settings” under the

“Network Settings” setup (page 51).

When connecting to a broadband router directly

Blu-ray Disc/DVD player

Network cable

(not supplied)

Broadband router

To PC

Network cable

(not supplied)

To update the player’s software using the network

See “Network Update” (page 41) and

“Software Update Notification” (page 50).

b

Do not connect a phone line to the LAN (100) terminal, as it may cause a malfunction.

ADSL modem/

Cable modem

Internet

About network (LAN) cables

Depending on the modem or router, the type of network (LAN) cable, straight or crossing, differs. For details on the network (LAN) cables, refer to the operating instructions supplied with the modem or router.

When connecting via a wireless LAN router

Blu-ray Disc/DVD player

Step 5: Connecting the

AC Power Cord

After all of the other connections are complete, connect the supplied AC power cord to the AC IN terminal of the player.

Then plug the player and TV power cords into the AC outlet.

Network cable

(not supplied)

Ethernet/wireless

LAN media converter

1 to AC IN

2 to AC outlet

To PC

Wireless LAN router

(access point)

Network cable

(not supplied)

ADSL modem/

Cable modem

Internet

b

Do not connect the LAN terminal of the player to the LAN terminal of the PC.

25

Step 6: Preparing the

Remote

You can control the player using the supplied remote. Insert two Size AA (R6) batteries by matching the 3 and # ends on the batteries to the markings inside the battery compartment. When using the remote, point it at the remote sensor on the player

(page 10).

Controlling TVs with the remote

You can control the volume, input source, channel, and power switch of your Sony TV with the supplied remote.

b

When you replace the batteries of the remote, the code number may be reset to the default setting. Set the appropriate code number again.

TV [/1

Number buttons

26

b

• Use the batteries correctly to avoid possible leakage and corrosion. Should leakage occur, do not touch the liquid with bare hands. Observe the following:

– Do not use a new battery with an old battery, or batteries of different manufacturers.

– Do not attempt to recharge the batteries.

– If you do not intend to use the remote for an extended period of time, remove the batteries.

– If battery leakage occurs, wipe out any liquid inside the battery compartment, and insert new batteries.

• Do not expose the remote sensor (marked on the front panel) to strong light, such as direct sunlight or a lighting apparatus. The player may not respond to the remote.

MUTING

VOL +/–

INPUT

CH +/–

Available buttons

Depending on the connected unit, you may not be able to control your TV with some or all of the buttons (TV [/1, CH +/–, VOL +/–,

MUTING, or number buttons).

Buttons

TV [/1

VOL (volume)

+/–

CH (channel)

+/–

INPUT

(input select)

MUTING

Operations

Turns your TV on or off.

Adjusts the volume of your TV.

Selects the channel on your TV.

Switches your TV’s input source between the TV and other input sources.

Mutes the sound.

To control other TVs with the remote

You can control the volume, input source, channel, and power switch of non-Sony TVs as well.

If your TV is listed in the table below, set the appropriate manufacturer’s code.

b

If you enter a new code number, the code number previously entered will be erased.

1

While holding down TV [/1, enter the

TV’s manufacturer code using the number buttons.

For instance, to enter “09,” press “0” then

“9.”

Code numbers of controllable TVs

If more than one code number is listed, try entering them one at a time until you find the one that works with your TV.

Manufacturer

Sony

Admiral

Akai

AOC

Bell & Howell

Broksonic

CCE

Craig

Croslex

Crown

Curtis Mathis

Daewoo

Daytron

Emerson

Fisher

Funai

General Electric

LG/Goldstar

Gradients

Hitachi

J.C.Penney

JVC

Code number

01 (default)

10, 18

04, 12

04

18

04, 12

08, 22

14

08

14

04, 07, 12, 14

04, 12, 22

03

03, 04, 05, 12, 14,

23

11

23

04, 06, 10, 12

03, 04, 12, 17

09

02, 03, 04

04, 10, 12, 17

09

Manufacturer

KTV

LXI (Sears)

Magnavox

Marantz

Mitsubishi/MGA

NEC

Panasonic

Philco

Philips

Pioneer

Portland

Quasar

Radio Shack

RCA/PROSCAN

Samsung

Sanyo

Scott

SEMP Toshiba

Sharp

Signature2000

Sylvania

Symphonic

Toshiba

Videch

Wards

Zenith

2

Release TV [/1.

Code number

03, 04, 12, 14

04, 07, 08, 10, 11,

12

03, 04, 06, 08, 12,

21

13

04, 12, 13

04, 12

06, 19

02, 03, 04, 08, 12

08, 21

06, 07, 16

04, 12

06

04, 05, 10, 13, 14

04, 10, 12

03, 04, 12, 20

11, 14

04, 12, 14

07

03, 05, 18

18

04, 08, 12, 23

14

07, 18

02, 04, 12

03, 04, 12

15

27

Step 7: Easy Setup

Follow the steps below to make the minimum number of basic adjustments for using the player. If you do not complete Easy Setup, it will appear each time you turn on your player.

Make the settings below in the following order.

4

Select a language for the on-screen

displays using M/m, and press

ENTER.

When turned on for the first time

Wait for a short while before the player turns on and starts Easy Setup.

The initial settings message appears.

5

Select “Start,” and press ENTER.

[/1

TV [/1

</M/m/,,

ENTER

6

Select the cable type used to connect the player and your TV, and press

ENTER.

RETURN

HOME

28

1

Turn on the TV.

2

Press [/1 to turn on the player.

The player turns on after a moment.

3

Switch the input selector on your TV so that the signal from the player appears on your TV screen.

The display for OSD language selection appears.

• If the display for OSD language selection does not appear

Press HOME, and select “Easy Setup”

in the “Setup” setup (page 53). Then,

select “Start,” and press ENTER.

Select “HDMI” when connecting your

TV using the HDMI cable, and go to step

7.

b

When connecting the HDMI OUT jack and other video output jacks at the same time, select “Component Video.”

Select “Component Video” when connecting your TV using the component

video cable, and go to step 7.

Select “Video or S Video” when connecting your TV using the video

cable or S-video cable, and go to step 8.

7

Select a video output resolution for the connected TV, and press ENTER.

For details about the video output

resolution, see page 44.

When you select “HDMI” in step 6

Select from “Auto,” “480i,” “480p,”

“720p,” “1080i,” or “1080p.”

When connecting the HDMI OUT jack and other video output jacks at the same time, video signals may not output from the jacks, other than from the HDMI

OUT jack, when “Auto” or “1080p” is selected.

When connecting other equipment at the same time, press RETURN to return to step 6 and change the “TV Connection

Method” setting.

When you select “Component Video” in

step 6

b

If the picture is distorted or no picture appears, wait for about 30 seconds without pressing any buttons. The display returns to the resolution setting screen.

If the selected video output resolution is incorrect, no picture appears on the screen when you press any button in 30 seconds. In this case, press x on the player for more than

10 seconds to reset the video output resolution to the lowest resolution. To change the video output resolution, set “Output Video Format”

in the “Video Settings” setup (page 43).

8

Select an aspect ratio that matches your TV, and press ENTER.

Select “16:9” when connecting to a widescreen TV or a TV with a wide mode function.

Select “4:3” when connecting to a 4:3 screen TV without a wide mode function.

9

(Only when connecting your TV using the HDMI cable)

Set the “Control for HDMI” function to

“On” or “Off,” and press ENTER.

Select from “480i,” “480p,” “720p,” or

“1080i.”

When you change the video output resolution, a picture is displayed in the selected resolution for about 30 seconds, then the display asks for confirmation.

Follow the on-screen instructions and go to the next step.

Select “On” to use the “Control for

HDMI” function when connecting Sony components that are compatible with the

“Control for HDMI” function (page 16).

If you do not use the “Control for HDMI” function, select “Off.”

,continued

29

30

10

Select “Finish,” and press ENTER.

z

• You can reset settings to their factory settings

(page 53).

• You can run “Easy Setup” again from “Easy

Setup” in “Setup” (page 53).

Playback

Playing BDs/DVDs

BD DVD

Z OPEN/

CLOSE

Number buttons

</M/m/,,

ENTER

OPTIONS

HOME

N PLAY

X PAUSE x STOP

1

Switch the input selector on your TV so that the signal from the player appears on your TV screen.

2

Press Z OPEN/CLOSE, and place a

disc on the disc tray.

Playing side facing down

3

Press Z OPEN/CLOSE to close the

disc tray.

• When you insert a commercially available BD-ROM or DVD VIDEO, playback automatically starts depending on the disc.

b

Playback does not start by pressing N PLAY while the disc tray is open.

,continued

31

32

4

Press HOME.

5

Select “Video” using </,.

6

Select

N

PLAY or ENTER.

For commercially available BD-ROMs or DVD VIDEOs, playback starts.

For BDs or DVDs recorded on other equipment, the title list appears. Select a title using M/m, and press N PLAY or

ENTER.

Playback starts.

To stop playback

Press x STOP.

To pause playback

Press X PAUSE.

z

In the title list, “PL” (Playlist) is displayed next to the name of titles that are created and edited from their originals.

b

• Depending on the disc you may not be able to do some of the playback operations. Refer to the instruction manual supplied with the disc.

• Depending on BDs or DVDs recorded on other equipment, title lists or title names may not be displayed.

To resume playback from the point where you stopped (Resume Play)

After stopping playback, select using

M/ m, and press N PLAY or ENTER.

The player resumes playback from the point where you pressed x STOP.

To start from the beginning, press OPTIONS to select “Play from beginning,” and press

ENTER. Playback starts from the beginning of the title.

b

• The point where you stopped playing is cleared from memory when:

– you open the disc tray,

– you play another title,

– you change the settings on the player, or

– you remove the external memory (for BD-

ROMs).

• The player may not resume playback depending on the disc or stop point.

To play restricted BDs or DVDs (Parental

Control)

When you play a restricted BD, change the

“BD Parental Control” setting in the “BD/

DVD Viewing Settings” setup (page 47).

When you play a restricted DVD, the display for entering your password appears on the screen.

Enter your four-digit password using the number buttons, and press ENTER.

Playback starts.

To register or change the password, see

“Password” (page 49).

To play restricted BD-REs or BD-Rs (Disc

Lock)

When you play a BD-RE or BD-R restricted by the Disc Lock function, the display for entering your password appears on the screen.

1

Enter the four-digit password that has been registered when creating the disc using the number buttons, and press

ENTER.

2

Select a title, and press N PLAY or

ENTER.

Playback starts.

One-Touch Play (for HDMI connection only)

Press N PLAY.

The player and the connected TV turn on and the input selector on the TV is switched to the player, then playback starts automatically.

b

• When using the HDMI connection, there may be a delay before the playback picture appears on the screen, and the beginning portion of the playback picture may not be displayed.

• To use the One-Touch Play function, set “Control for HDMI” to “On” in the “System Settings”

setup (page 50).

Available OPTIONS

1

Press OPTIONS.

The options menu appears.

2

Select an item using M/m, and press

ENTER.

The available items differ depending on the disc type or player situation.

Items Details

A/V Settings

Adjusts settings for picture and sound.

• Video Settings

(page 35)

• Audio Settings

(page 36)

Title List

Play

Play from beginning

Top Menu

Menu/Popup

Menu

Stop

Title Search

Chapter

Search

Displays the title list.

Plays the title from the point where you pressed x STOP.

Plays the title from the beginning.

Displays the disc’s Top

Menu (page 33).

Displays the BD-

ROM’s Pop-up Menu or

DVD’s menu (page 33).

Stops playback.

Searches for a title and starts playback from the

beginning (page 34).

Searches for a chapter and starts playback from the beginning

(page 34).

Using the BD’s or DVD’s menu

BD DVD

To display Top Menu

When you play a BD or DVD, you can display the Top Menu.

1

Press TOP MENU during playback.

The Top Menu appears.

2

Select an item using </M/m/,.

To display Pop-up Menus

Some BD-ROMs contain Pop-up Menus that appear without interrupting playback.

1

Press POP UP/MENU during playback.

The Pop-up Menu appears.

2

Select an item using </M/m/,, color buttons, or the number buttons, and follow the on-screen instructions.

Enjoying BonusView

BD

Some BD-ROMs have bonus contents and other data that can be downloaded to the external memory (local storage) for enjoyment.

1

Turn the player off.

2

Insert the external memory (not supplied) into the EXT slot on the rear of the player.

The external memory is used as the local storage.

Make sure that the external memory is properly inserted into the player

(page 23).

3

Turn the player on.

4

Insert a BD-ROM with BonusView.

The operation method differs depending on the disc. Refer to the instruction manual supplied with the disc.

,continued

33

To delete data in the external memory

You can delete all unnecessary data at once.

1

Press HOME.

2

Select “Video” using </,.

3

Select “BD Data” using M/m, and press

OPTIONS.

4

Select “Erase,” and press ENTER.

5

Select “OK,” and press ENTER.

Searching for a scene quickly

(Scene Search)

BD DVD

You can move quickly between scenes within the title currently being played back.

1

Press SCENE SEARCH during playback or in pause mode.

Playback pauses and a bar with a scene indicator (square-shaped – indicates the current point) appears at the bottom of the screen.

2

Move the scene indicator to the scene

you are searching for using </, or m /M.

Scene indicator

4

Press SCENE SEARCH, ENTER,

N PLAY, or X PAUSE.

Playback starts.

To cancel Scene Search mode

Press SCENE SEARCH, ENTER,

N PLAY, or X PAUSE.

Playback starts from the point you pressed the button.

b

The Scene Search function is available for titles longer than 100 seconds and shorter than 100 hours.

Searching for a Title/Chapter

BD DVD

You can search for a chapter if the title contains chapter marks.

1

Press OPTIONS during playback or in pause mode.

The options menu appears.

2

Select a search method using M/m,

and press ENTER.

“Title Search” (for BD-ROMs/DVD

VIDEOs)

“Chapter Search”

The display for entering the number appears.

Example: Chapter Search

34

The current point

The scene indicator on the bar is displayed around the playing point.

3

Release the button at the point you want to watch.

The scene at which you released the button is displayed in pause mode.

To search for a scene again, move the scene indicator using </, or m/

M.

3

Enter the number of the title or chapter using the number buttons.

If you make a mistake, press CLEAR, and re-enter another number.

4

Press ENTER.

After a while, the player starts playback from the selected number.

Displaying the playing time and play information

BD DVD

You can check the title information, including the video transmission rate, etc.

Press DISPLAY.

The displayed information differs depending on the disc type and player status.

Example: When playing a BD-ROM

Adjusting pictures and sound for videos

BD DVD

To adjust the picture

1

Press OPTIONS during playback.

The options menu appears.

2

Select “A/V Settings” using M/m, and press ENTER.

3

Select “Video Settings” using M/m, and press ENTER.

The “Video Settings” screen appears.

A The current selected angle

B Title number or name

C The currently selected audio or subtitle setting

D Available functions (

angle/ audio/ subtitle)

E Playback information

Displays Disc type/Play mode/Video codec/Bit rate/Playing status bar/

Playing time (Remaining time*)

F Output resolution/Video frequency

* Displayed when you press TIME repeatedly.

z

• You can also check the playback information in

the front panel display (page 11).

• Press SUBTITLE, AUDIO, or ANGLE, and you can check each type of information.

4

Select an item using

M/m, and press

ENTER.

The default settings are underlined.

Items Details

Picture Quality

Mode

(Standard/

Brighter

Room/Theater

Room)

Optimizes the picture settings for different lighting environments.

FNR

(Off/Auto)

BNR

(Off/Auto)

Reduces random noise appearing in the picture.

Reduces mosaic-like block noise in the picture.

MNR

(Off/Auto)

Reduces minor noise around the picture outlines (mosquito noise).

5

Select or adjust the settings using </M/ m/,, and press ENTER.

To adjust any other items, repeat steps 4 and 5.

,continued

35

b

• Set the picture setting of your TV to ‘Standard’ before changing the “Picture Quality Mode” setting.

• “Video Settings” is not available when the

connected TV is set to Theater Mode (page 16).

• Depending on the disc or the scene being played,

“FNR,” “BNR” or “MNR” effects may be hard to discern.

To adjust the audio characteristics

1

Press OPTIONS during playback.

The options menu appears.

2

Select “A/V Settings” using M/m, and press ENTER.

3

Select “Audio Settings” using M/m, and press ENTER.

The “Audio Settings” screen appears.

b

• The “Audio Filter” function does not work for digital audio signals output from the HDMI OUT/

DIGITAL OUT (OPTICAL/COAXIAL) jacks.

• There may be little effect by changing the “Audio

Filter” setting depending on the disc or playback environment.

36

4

Select an item using M/m, and press

ENTER.

The default settings are underlined.

Items

AV SYNC

(short) 0 ~

120 msec

(long)

Details

Adjusts the gap between picture and sound, by delaying the sound output in relation to the picture output (0 to

120 milliseconds).

Audio Filter

(for analog audio signals only)

• Sharp: Provides a wide frequency range and spatial feeling.

Normally select this.

• Slow: Provides smooth and warm sound.

5

Select or adjust the settings using

</M/ m/,, and press ENTER.

To adjust any other items, repeat steps 4 and 5.

Playing CDs

CD

1

Insert a CD.

The Music Player screen appears.

2

Press N PLAY.

Playback starts.

To select a track

1

Press HOME.

2

Select (Music) using

</,.

3

Select , and press ENTER.

The music list appears.

4

Select a track using

M/m.

To play the selected track, press

N PLAY or ENTER.

Available OPTIONS

1

Press OPTIONS.

The options menu appears.

2

Select an item using

M/m, and press

ENTER.

The available items differ depending on the situation.

Items

Play

Play from beginning

Stop

Details

Plays the selected track.

Plays the current track from the beginning.

Stops playing the track.

Various music playback operations

Buttons

N PLAY x STOP

X PAUSE

. PREV/

NEXT > m/M

TIME

Operations

Starts playback from the point where you pressed x STOP.

Stops playback.

Pauses playback.

Skips to the beginning of the current or next track. To go to the previous track press

. PREV twice.

Fast reverse/fast forwards when pressed during playback.

Switches time information on the screen and the front

panel display (page 11).

b

The point where you stopped playing (resume point) is cleared from memory when:

– you open the disc tray, or

– you turn off the player.

37

38

Playing Photo Files

BD

*1

DATA DVD

*2

DATA CD

*3

*1

BD-REs/BD-Rs containing JPEG image files

*2

DVD+RWs/DVD+Rs/DVD-RWs/DVD-Rs containing JPEG image files

*3

CD-RWs/CD-Rs containing JPEG image files

1

Press HOME.

2

Select

3

Select , and press ENTER.

The file list or folder list appears.

4

Select a file or folder using M/m, and

press ENTER.

When you select a folder, select a file in the folder using M/m, and press ENTER.

The selected photo file is displayed.

• To play a slideshow, press N PLAY.

Available OPTIONS during playback

1

Press OPTIONS during playback.

The options menu appears.

2

Select an item using M/m, and press

ENTER.

The available items differ depending on the situation.

Items

Slideshow

Speed

Details

Changes the slideshow speed.

• Fast

• Normal

• Slow

Stop

Rotate Left

Stops a slideshow.

Rotates the photo counterclockwise by 90 degrees.

Rotate Right Rotates the photo clockwise by 90 degrees.

Various photo playback operations

Buttons

x STOP

RETURN

X PAUSE

. PREV/

NEXT >

DISPLAY

Operations

Stops a slideshow.

Pauses a slideshow.

Displays the previous or next photo.

Displays the file information.

b

• When you attempt to play the following photo files, the mark appears on the screen and they cannot be played.

– photo files larger than 8,192 pixels (width or height)

– photo files smaller than 15 pixels (width or height)

– photo files exceeding 32 MB

– photo files with extreme aspect ratios (greater than 50:1 or 1:50)

– photo files in Progressive JPEG format

– photo files that have a “.jpeg” or “.jpg” extension, but not in JPEG format

– photo files that have an extremely long name

• The following photo files cannot be played.

– photo files recorded on BD-Rs in any format other than UDF (Universal Disk Format) 2.6

– photo files recorded on BD-REs in any format other than UDF (Universal Disk Format) 2.5

• The following photo files or folders cannot be displayed in the file list or folder list.

– photo files that have an extension other than

“.jpeg” or “.jpg”

– photo files that have an extremely long name

– photo files in the 5th tree or lower

– 501th or more folders when the total number of folders and files in a single tree exceeds 500

• Photo files edited on a PC may not be played.

• Thumbnail images of some photo files may not be displayed.

• Large photo files may take some time to display or to start a slideshow.

To view best quality images

If you have a Sony TV compatible with

“PhotoTV HD,” you can enjoy best quality images by the following connection and setting.

1

Connect the player to the TV using an

HDMI cable (supplied).

2

Set the TV’s video setting to [VIDEO-A] mode.

For details on [VIDEO-A], refer to the operating instructions supplied with the

TV.

39

40

Using the Settings

Displays

Select (Setup) on the home menu when you need to change the settings of the player.

1

Press HOME.

2

Select

(Setup) using </,.

Settings and

Adjustments

3

Select the setup category icon to

change using M/m, and press ENTER.

For details on setting options and setup

category icons, see “Setting list”

(page 41).

Example: Video Settings

4

Set the options.

Setting list

You can setup the following options.

Icon Explanation

Network Update (page 41)

Updates the software of the player.

Video Settings (page 42)

Makes the video settings according to the type of connecting jacks.

Audio Settings (page 45)

Makes the audio settings according to the type of connecting jacks.

BD/DVD Viewing Settings

(page 47)

Makes detailed settings for BD/

DVD playback.

Photo Settings (page 49)

Makes the photo-related settings.

System Settings (page 50)

Makes the player-related settings.

Network Settings (page 51)

Makes detailed settings for

Internet and network.

Easy Setup (page 53)

Re-runs the Easy Setup to make the basic settings.

Resetting (page 53)

Resets the player to the factory settings.

Network Update

You can update and improve the functions of the player.

For information about update functions, refer to the following website; http://www.sony.net/

1

Select “Network Update” using M/m,

and press ENTER.

The player connects to the network, and the display asks for confirmation.

2

Select “OK” using </,, and press

ENTER.

The player starts downloading, then updating the software automatically.

When updating finishes, “FINISH” appears for 5 seconds in the front panel display, then the player automatically turns off.

3

Press [/1 to turn on the player.

The player starts up with the updated software.

z

• The “VUP */9” counter (“*” indicates update step) in the front panel display also shows progress of the update.

• You can check the current software version by selecting “System Information” in the “System

Settings” setup (page 50).

• The “Setup” settings remain after updating.

• The player informs you of newer software version information when “Software Update

Notification” is set to “On” (default) (page 50).

b

• Do not disconnect the AC power cord or network cable while downloading or updating software.

• Any operations, including opening the disc tray, are not available while updating.

• Downloading times may differ depending on the server provider or line status.

• When error messages on network connections appear, check the network connections using

“Network Diagnostic” of “Internet Settings” in

the “Network Settings” setup (page 51).

,continued

41

42

To update the software using an update disc

You can update and improve the functions of the player using an update disc provided by

Sony dealer or local authorized Sony service facility.

1

Insert the update disc.

The display asks for confirmation.

2

Select “OK,” and press ENTER.

Software update starts.

When updating finishes, “FINISH” appears for 5 seconds in the front panel display, then the disc tray automatically opens.

3

Remove the disc.

The player automatically turns off.

4

Press [/1 to turn the player on.

The player starts up with the updated software.

z

• The “VUP */9” counter (“*” indicates update step) in the front panel display also shows progress of the update.

• You can check the current software version by selecting “System Information” in the “System

Settings” setup (page 50).

• The “Setup” settings remain after updating.

• For information about other software update methods, refer to the following website or consult your nearest Sony dealer or local authorized Sony

Service facility; http://www.sony.net/

b

• Do not disconnect the AC power cord while updating.

• Any operations, including opening the disc tray, are not available while updating.

Video Settings

The default settings are underlined.

TV Type

Selects your TV type.

16:9

4:3

Select this when connecting to a wide-screen TV or a TV with a wide mode function.

Select this when connecting to a 4:3 screen TV without a wide mode function.

Screen Format

Selects the display configuration for a 4:3 screen picture on a 16:9 wide screen TV.

Original

Fixed Aspect

Ratio

Select this when connecting to a TV with a wide mode function. Displays a 4:3 screen picture in 16:9 aspect ratio even on a wide-screen

TV.

Changes the picture size to fit the screen size with the original picture aspect ratio.

DVD Aspect Ratio

Selects the display configuration for playback of 16:9 screen pictures on a 4:3 screen TV (selectable when “TV Type” is set to “4:3” and “Screen Format” is set to “Fixed

Aspect Ratio”).

Letter Box

Pan & Scan

Displays a wide picture with black bands on the top and bottom.

Displays a full-height picture on the entire screen, with trimmed sides.

Letter Box

Pan & Scan

Cinema Conversion Mode

Sets the video conversion method for 480p,

720p, 1080i, or 1080p* signals from the

HDMI OUT jack or the COMPONENT

VIDEO OUT jacks.

* HDMI only

Auto

Video

Normally select this. The player automatically detects whether the material is video-based or film-based, and switches to the appropriate conversion method.

The conversion method suited for video-based material will always be selected regardless of the material.

Output Video Format

Selects the jack type to output video signals

(“TV Connection Method”) and output resolution (“HDMI Resolution”/“Component

Resolution”).

1

Select “Output Video Format” in “Video

Settings,” and press ENTER.

2

Select the jack type to output video signals using

M/m, and press ENTER.

b

When connecting the HDMI OUT jack and other video output jacks at the same time, select “Component Video.”

TV Connection Method

HDMI Outputs signals from the HDMI OUT jack according to the “HDMI

Resolution” setting below.

Component

Video

Video or

S Video

Outputs signals from the COMPONENT

VIDEO OUT jacks according to the

“Component

Resolution” setting below.

Outputs signals from the LINE OUT VIDEO or S VIDEO jack.

3

(When you select “HDMI” or

“Component Video” only)

Select the signal type for the HDMI OUT jack or COMPONENT VIDEO OUT jacks using M/m, and press ENTER.

When you change the video output resolution, a picture is displayed in the selected resolution for about 30 seconds, then the display asks for confirmation.

Follow the on-screen instructions.

The HD indicator lights up when outputting 720p/1080i/1080p video signals.

,continued

43

44

b

• If the picture is distorted or no picture appears, wait for about 30 seconds without pressing any buttons. The display returns to the resolution setting screen.

If the selected video output resolution is incorrect, no picture appears on the screen when you press any button in 30 seconds. In this case, press x on the player for more than

10 seconds to reset the video output resolution to the lowest resolution.

• When connecting the HDMI OUT jack and other video output jacks at the same time, video signals may not output from the jacks, other than from the HDMI OUT jack, when

“Auto” or “1080p” is selected.

When connecting other equipment at the same time, press RETURN to return to step

2 and change the “TV Connection Method”

setting.

HDMI Resolution/Component Resolution

Auto (HDMI only)

Normally select this.

The player outputs signals starting from the highest resolution acceptable to the TV:

1080p > 1080i > 720p >

480p > 480i

If the resulting image format is undesirable, try another setting that suits your TV.

480i

480p

720p

Outputs 480i video signals.

Outputs 480p video signals.

Outputs 720p video signals.

1080i

1080p (HDMI only)

Outputs 1080i video signals.

Outputs 1080p video signals.

BD-ROM 1080/24p Output

Sets to output 1920 × 1080p/24 Hz video signals when playing film-based materials on

BD-ROMs (720p/24 Hz or 1080p/24 Hz).

1920 × 1080p/24 Hz video signals can be output when all of the following conditions are met.

– You connect a 1080/24p-compatible TV using the HDMI OUT jack,

– “Output Video Format” is set to “HDMI,” and

– “HDMI Resolution” is set to “Auto” or

“1080p.”

The 24P indicator lights up when outputting

1920

× 1080p/24 Hz video signals.

Auto

On

Off

Outputs 1920 × 1080p/

24 Hz video signals only when connecting a 1080/

24p-compatible TV using the HDMI OUT jack.

Outputs 1920 × 1080p/

24 Hz video signals regardless of the connected

TV type.

Select this when your TV is not compatible with 1080/

24p video signals.

b

No BD-ROM picture appears when the connected

TV is non-compatible with 1080/24p and “BD-

ROM 1080/24p Output” is set to “On.” In this case, press HOME to display the home menu, and change the “BD-ROM 1080/24p Output” setting.

YCbCr/RGB (HDMI)

Sets the color setting for video signals output from the HDMI OUT jack. Select the setting that matches the connected TV type.

Auto

Automatically detects the type of external device, and switches to the matching color setting.

YCbCr (4:2:2) Outputs YCbCr 4:2:2 video signals.

YCbCr (4:4:4) Outputs YCbCr 4:4:4 video signals.

RGB (16-235) Select this when connecting to a device with an HDCPcompliant DVI jack.

RGB (0-255) Select this when connecting to an RGB (0-255) device.

Audio Settings

The default settings are underlined.

Audio Output Priority

Selects the jack type to output audio signals.

2-channel linear PCM signals are output at

48 kHz maximum from output jacks other than the priority jacks.

HDMI Outputs audio signals from the HDMI OUT jack.

Coaxial/

Optical

Outputs audio signals from the DIGITAL OUT

(OPTICAL/COAXIAL) jack.

Stereo Analog Outputs audio signals from the LINE OUT (R-AUDIO-

L) jacks.

x.v.Color Output

Sets whether to send xvYCC information to the connected TV.

Combining xvYCC-compatible video with a

TV that supports x.v.Color display makes it possible to more accurately reproduce object colors present in the natural world.

Auto

Off

Normally select this.

Select this when the picture is unstable or colors appear unnatural.

Pause Mode

Sets the picture mode for DVD playback pause status. For BD-ROMs or discs containing AVCHD files, “Pause Mode” automatically switches to “Auto.”

Auto

Frame

Normally select this.

Dynamic moving pictures appear without blurring.

Displays static pictures at high resolution.

Audio (HDMI)

Selects the signal type for the HDMI OUT jack.

Auto

2ch PCM

Normally select this.

Outputs audio signals according to the status of the connected HDMI device.

Downmixes to 2-channel

Linear PCM signals before outputting from the HDMI

OUT jack.

b

Select “2ch PCM” when connecting a TV or an AV amplifier (receiver) that does not support Dolby

Digital or DTS, otherwise noise or no sound may result.

BD Audio Setting

Selects whether to mix or not mix interactive audio and secondary audio (commentary) when playing a BD that contains such audio.

Mix

Direct

Outputs the audio obtained by mixing the interactive audio and secondary audio to the primary audio.

Outputs the primary audio only.

,continued

45

46

Audio ATT

Lowers the audio output level to prevent sound distortion.

On

Off

Enables Audio Attenuation.

Disables Audio Attenuation.

b

“Audio ATT” does not affect the output from the

HDMI OUT jack and the DIGITAL OUT

(OPTICAL/COAXIAL) jack.

Dolby Digital

Selects the audio signals output when playing

Dolby Digital discs.

This setting affects the output from the

DIGITAL OUT (COAXIAL/OPTICAL) jack.

Downmix

PCM

Converts to output Linear

PCM signals. Select this when connecting an audio device without a built-in

Dolby Digital decoder.

Dolby Digital Select this when connecting an audio device with a builtin Dolby Digital decoder.

48kHz/96kHz PCM

Selects the maximum sampling frequency for the PCM signals output from the DIGITAL

OUT (OPTICAL/COAXIAL) jack.

48kHz/16bit

96kHz/24bit

Outputs audio signals of

96 kHz sampling as 48 kHz/

16 bit.

Outputs audio signals of

96 kHz sampling as 96 kHz/

24 bit. However, the signals will be output as 48 kHz/

16 bit if the source is copyprotected.

b

• If you select “96kHz/24bit” when an AV amplifier (receiver) that does not support 96 kHz is connected, no sound or a loud sound may result.

• “48kHz/96kHz PCM” is not effective when

“Audio Output Priority” is set to “HDMI” or

“Stereo Analog.”

DTS

Selects the audio signals output when playing

DTS discs. This setting affects the output from the DIGITAL OUT (COAXIAL/

OPTICAL) jack.

Downmix

PCM

DTS

Converts to output Linear

PCM signals. Select this when connecting to an audio device without a built-in

DTS decoder.

Select this when connecting to an audio device with a built-in DTS decoder.

Audio DRC

Selects the dynamic range (compression level of the sound) setting when playing a BD or

DVD that conforms to “Audio DRC.”

Auto Performs playback at the dynamic range specified by the disc (BD-ROM only).

Other discs are played back at the “Standard” level.

Standard

TV Mode

Performs playback at a compression level between

“TV Mode” and “Wide

Range.”

Sounds are compressed heavily. Low sounds are easier to hear.

Wide Range

No compression works. A more dynamic sound is produced.

b

• “Audio DRC” is effective only when playing

Dolby Digital, Dolby Digital Plus, and Dolby

TrueHD audio signals.

• When “Dolby Digital” is set to “Dolby Digital” in

the “Audio Settings” setup (page 46), “Audio

DRC” has no effect on the audio output from the

DIGITAL OUT (OPTICAL/COAXIAL) jack.

However, this excludes the following cases.

– when “BD Audio Setting” is set to “Mix” when playing a BD.

– when “Audio Output Priority” is set to “HDMI” or “Stereo Analog.”

Downmix

Sets the downmix method of multi-channel to two-channel sound.

Dolby

Surround

Normal

Outputs the Dolby Surround

(Pro Logic) signals in 2 channels. Select this when connecting an audio device that supports Dolby

Surround (Pro Logic).

Outputs audio signals without Dolby Surround

(Pro Logic) effect. Select this when connecting an audio device that does not support Dolby Surround

(Pro Logic).

b

“Downmix” has no effect on the bitstream audio output from the DIGITAL OUT (OPTICAL/

COAXIAL)/HDMI OUT jack.

BD/DVD Viewing

Settings

The default settings are underlined.

BD/DVD Menu

Selects the default menu language for BD-

ROMs or DVD VIDEOs.

When you select “Select Language Code,” the display for entering the language code appears. Enter the code for your language by

referring to “Language Code List” (page 65).

Audio

Selects the default track language for BD-

ROMs or DVD VIDEOs.

When you select “Original,” the language given priority in the disc is selected.

When you select “Select Language Code,” the display for entering the language code appears. Enter the code for your language by

referring to “Language Code List” (page 65).

Subtitle

Selects the default subtitle language for BD-

ROMs or DVD VIDEOs.

When you select “Select Language Code,” the display for entering the language code appears. Enter the code for your language by

referring to “Language Code List” (page 65).

BD Parental Control

Playback of some BD-ROMs can be limited according to the age of the users. Scenes may be blocked or replaced with different scenes.

1

Select “BD Parental Control” in “BD/

DVD Viewing Settings,” and press

ENTER.

2

Enter your four-digit password using the number buttons.

3

Select “OK,” and press ENTER.

,continued

47

48

4

Select the age restriction, and press

ENTER.

The lower the value, the stricter the limitation.

If you select “Select Age Restriction,” you can enter the age from “0” to “255” using

</M/m/, or the number buttons.

• To cancel the Parental Control setting, select “No Restrictions.” z

You can change the password (see “Password” on page 49).

b

• If you forget the password, reset the player

(page 53) and set a new password (see

“Password” on page 49).

• When you play discs which do not have the

Parental Control function, playback cannot be limited on this player.

• Depending on the disc, you may be asked to change the Parental Control level while playing the disc. In this case, enter your password, then change the level.

z

You can change the password (see “Password” on page 49).

b

• If you forget the password, reset the player

(page 53) and set a new password (see

“Password” on page 49).

• When you play discs which do not have the

Parental Control function, playback cannot be limited on this player.

• Depending on the disc, you may be asked to change the Parental Control level while playing the disc. In this case, enter your password, then change the level.

• When “255” is selected in “Select Age

Restriction,” the Parental Control setting is canceled.

DVD Parental Control

Playback of some DVD VIDEOs can be limited according to the age of the users.

Scenes may be blocked or replaced with different scenes.

1

Select “DVD Parental Control” in “BD/

DVD Viewing Settings,” and press

ENTER.

2

Enter your four-digit password using the number buttons.

3

Select “OK,” and press ENTER.

4

Select a level, and press ENTER.

The lower the value, the stricter the limitation.

• To cancel the Parental Control setting, select “No Restrictions.”

Parental Control Region Code

Playback of some BD-ROMs or DVD

VIDEOs can be limited according to the geographic area. Scenes may be blocked or replaced with different scenes.

1

Select “Parental Control Region

Code” in “BD/DVD Viewing Settings,” and press ENTER.

2

Enter your four-digit password using the number buttons.

3

Select “OK,” and press ENTER.

4

Select the area restriction, and press

ENTER.

When you select “Select Region Code,” the display for entering the region code appears. Enter the code for the area

restriction by referring to “Parental

Control/Area Code” (page 65).

z

You can change the password (see “Password” on page 49).

b

• If you forget the password, reset the player

(page 53) and set a new password (see

“Password” on page 49).

• When you play discs which do not have the

Parental Control function, playback cannot be limited on this player.

• Depending on the disc, you may be asked to change the Parental Control level while playing the disc. In this case, enter your password, then change the level.

Password

Sets or changes the password for the Parental

Control function. A password allows you to set a restriction on BD-ROM or DVD

VIDEO playback. If necessary, you can differentiate the restriction levels for BD-

ROMs and DVD VIDEOs.

1

Select “Password” in “BD/DVD

Viewing Settings,” and press ENTER.

2

Enter your four-digit password using the number buttons.

3

Select “OK,” and press ENTER.

Photo Settings

The default setting is underlined.

Slideshow Speed

Changes the slideshow speed.

Fast

Normal

Slow

Photos change rapidly.

Photos change at normal speed.

Photos change slowly.

To change the password

1

After step 3, enter a new password using

the number buttons.

2

Select “OK,” and press ENTER.

Hybrid Disc Playback Layer

Selects the layer priority when playing a

Hybrid Disc. To change the setting, turn the player off and on again.

BD

DVD/CD

Plays BD layer.

Plays DVD or CD layer.

49

50

System Settings

The default settings are underlined.

Auto Display

OSD

Selects your language for the player onscreen displays.

On

Off

Automatically displays information on the screen when changing the viewing titles, picture modes, audio signals, etc.

Displays information only when you press DISPLAY.

Dimmer

Adjusts the lighting of the front panel display.

Bright

Dark

Off

Bright lighting.

Low lighting.

Turns off the lighting during playback. Low lighting other than during playback.

Control for HDMI

Screen Saver

The screen saver image appears when you do not use the player for more than 15 minutes while an on-screen display, such as the home menu, is displayed on your TV screen. The screen saver image helps prevent your display device from becoming damaged

(ghosting).

On

Off

Turns on the screen saver function.

Turns off the function.

On

Off

Allows you to use the

“Control for HDMI”

function (page 16).

Turns off the function.

Standby Mode

Software Update Notification

Informs you of newer software version information. Network connections and settings are required when using this function

(page 51).

On

Off

Sets the player to inform you of newer software version

information (page 41).

Turns off the function.

Quick Start Shortens the startup time from standby mode. You can operate the player quickly after turning it on.

The default setting.

Normal

b

When “Standby Mode” is set to “Quick Start,”

– power consumption will be higher than when

“Standby Mode” is set to “Normal” and

– the ventilation fan may turn on depending on the surrounding temperature.

System Information

Displays the player’s software version information and the MAC address.

Network Settings

Internet Settings

These items are necessary when you connect to the Internet via a network cable. Enter the respective (alphanumeric) values for your broadband router or Wireless LAN router.

The items that need to be set may differ, depending on the Internet service provider or the router. For details, refer to the instruction manuals that have been provided by your

Internet service provider or supplied with the router.

1

Select “Internet Settings” in “Network

Settings,” and press ENTER.

2

Select “IP Address Acquisition,” and press ENTER.

3

Select an item, and press ENTER.

Use DHCP

Use Static IP

Address

Select this when DHCP

(Dynamic Host

Configuration Protocol) server settings are available from your

Internet service provider. The network settings necessary for the player will be assigned automatically.

Set the IP address manually according to your network environment.

• When you select “Use DHCP”

If you set “DNS Server Auto

Acquisition” to “Off,” set the following item:

– DNS Server (Primary)/DNS Server

(Secondary)

• When you select “Use Static IP

Address”

Set the following items:

– IP Address

– Subnet Mask

– Default Gateway

– DNS Server (Primary)/DNS Server

(Secondary)

b

When you set the “DNS Server (Primary)”/

“DNS Server (Secondary)” addresses manually, enter the “DNS Server (Primary)” address. Otherwise, the “Internet Settings” will be set incorrectly.

4

If your ISP has a specific proxy server setting, select “Proxy Settings” using

M/m, and press ENTER.

The “Proxy Settings” display appears.

If the proxy server does not have a

specific setting, go to step 8.

5

Set “Use of Proxy Server” to “On.”

6

Select “Proxy Server” and “Port,” and enter the settings.

To enter the proxy server, see “To enter characters” (page 52).

7

Press RETURN.

8

Select “Network Diagnostic” using M/ m, and press ENTER.

9

Select “Start,” and press ENTER.

10

Check that the message “Network connections are correct.” appears.

The setup is finished. If the message does not appear, follow the on-screen messages.

,continued

51

52

To enter characters

The display for entering characters appears when you select “Proxy Server” in “Proxy

Settings.”

1

Press a number button repeatedly to select a character.

Example:

Press the number 3 button once to enter

“D.”

Press the number 3 button three times to enter “F.”

2

Press ,, and enter the next character.

3

Press the yellow button (“Finish”) to finish.

Available buttons

Buttons

Red button

(Letter Type)

Green button

(A/a)

Details

Switches the keyboard between alphabet and numbers.

Switches the keyboard between upper case and lower case.

Blue button

(Symbol)

Yellow button

(Finish)

Displays the keyboard for symbols.

The input is entered, and the player returns to the previous display.

CLEAR

(Clear/Clear All)

RETURN

(Cancel)

Erases the selected character.

To erase all displayed characters, press and hold

CLEAR for 2 seconds or more.

Returns to the previous display, canceling the input.

</M/m/,,

ENTER

• Select an input function using </M/m/,, and press ENTER.

• Enter characters as follows: 1Select a character selection panel using

</M/m/,, and press ENTER. 2Select a character using

</,, and press ENTER.

Easy Setup

Re-runs the Easy Setup to make the basic settings.

1

Select “Easy Setup,” and press

ENTER.

2

Select “Start” using </,, and

press ENTER.

3

Follow the instructions for “Step 7:

Easy Setup” (page 28) from step 4.

Resetting

You can reset the player settings to the factory default by selecting the group of settings. All the settings within the group will be reset.

1

Select “Resetting,” and press ENTER.

2

Select “Reset to Factory Default

Settings,” and press ENTER.

3

Select the settings you want to reset to default, and press ENTER.

The display asks for confirmation.

You can reset the following settings:

– Video Settings

– Audio Settings

– BD/DVD Viewing Settings

– Photo Settings

– System Settings

– Network Settings

– All Settings

4

Select “Start” using </,, and

press ENTER.

b

When “All Settings” is selected in step 3, the Blu-

ray Disc indicator lights up, then turns off when

Easy Setup is complete.

53

54

Additional

Information

Troubleshooting

If you experience any of the following difficulties while using the player, use this troubleshooting guide to help remedy the problem before requesting repairs. Should any problem persist, consult your nearest

Sony dealer.

Power

The power does not turn on.

, Check that the AC power cord is connected securely.

, It takes a short while before the player turns on.

The message “A new software version has been found on the network.” appears on the screen when turning the player on.

, See “Network Update” (page 41) to update

the player to a newer software version.

Disc

The disc does not play.

, The disc is dirty.

, The disc is upside down. Insert the disc with the playback side facing down.

, The disc is skewed.

, You are attempting to play a disc with a format that cannot be played back by this

player (page 60).

, The region code on the BD or DVD does not match the player.

, The player cannot play a recorded disc that

is not correctly finalized (page 60).

Picture

See also “Connecting to an HDMI jack”

(page 15) when connecting equipment using

the HDMI cable.

There is no picture/picture noise appears.

, Check that all the connecting cables are securely connected.

, Check whether the connecting cables are damaged.

, Check the connection to your TV (page 14)

and switch the input selector on your TV so that the signal from the player appears on the TV screen.

, When playing a double-layer DVD, the video and audio may be momentarily interrupted at the point where the layers switch.

No picture appears when the video output resolution selected in “Output Video

Format” is incorrect.

, Press x on the player for more than 10 seconds to reset the video output resolution to the lowest resolution.

The picture does not fill the screen, even though the aspect ratio is set in “DVD

Aspect Ratio” under “Video Settings.”

, The aspect ratio of the disc is fixed on your

DVD (page 43).

Sound

See also “Connecting to an HDMI jack”

(page 20) when connecting equipment using

the HDMI cable.

There is no sound.

, Check that all the connecting cables are securely connected.

, Check whether the connecting cables are damaged.

, Check the connection to your AV amplifier

(receiver) (page 19) and switch the input

selector on your AV amplifier (receiver) so that the audio signals of the player are output from your AV amplifier (receiver).

, The player is in scan mode.

, If the audio signal does not come through the DIGITAL OUT (OPTICAL/

COAXIAL)/HDMI OUT jack, check the

audio settings (page 45).

Video signals are not output from the jacks, other than from the HDMI OUT jack, when connecting the HDMI OUT jack and other video output jacks at the same time.

, Set “Output Video Format” to “Component

Video” in the “Video Settings” setup

(page 43).

The dark area of the picture is too dark/the bright area is too bright or unnatural.

, Set “Picture Quality Mode” to “Standard”

(default) (see “Adjusting pictures and sound for videos” on page 35).

The sound is not output correctly.

, Check the “Audio Output Priority” setting

in the “Audio Settings” setup (page 45).

The sound volume is low.

, The sound volume is low on some BDs or

DVDs.

, Try setting “Audio DRC” to “TV Mode” in

the “Audio Settings” setup (page 46).

, Set “Audio ATT” to “Off” in the “Audio

Settings” setup (page 46).

The picture is not output correctly.

, Check the “Output Video Format” settings

in the “Video Settings” setup (page 43).

No BD-ROM picture appears.

, Check the “BD-ROM 1080/24p Output” setting in the “Video Settings” setup

(page 44).

The HD Audio (Dolby digital Plus, Dolby

TrueHD, DTS-HD High Resolution Audio, and DTS-HD Master Audio) is not output by bitstream.

, Set “BD Audio Setting” to “Direct” in the

“Audio Settings” setup (page 45).

, Check that the connected AV amplifier

(receiver) is compatible with each HD

Audio format.

The interactive audio is not output.

, Set “BD Audio Setting” to “Mix” in the

“Audio Settings” setup (page 45).

,continued

55

HDMI

There is no picture or no sound when connected to the HDMI OUT jack.

, Try the following: 1Turn the player off and on again. 2Turn the connected equipment off and on again. 3Disconnect and then reconnect the HDMI cable.

There is no picture or picture noise appears when connected to the HDMI OUT jack.

, The HDMI OUT jack is connected to a DVI device that does not support copyright protection technology.

, If the HDMI OUT jack is used for video output, changing the video output resolution may solve the problem

(page 43).

, Make sure that the connected component is compatible with the “Control for HDMI” function. For details, refer to the operating instructions supplied with the component.

, Check the connected component’s setting for the “Control for HDMI” function. For details, refer to the operating instructions supplied with the component.

, If you change the HDMI connection, turn the player off and on again.

, If power failure occurs, set “Control for

HDMI” to “Off,” then set “Control for

HDMI” to “On” (page 50).

, For details on the “Control for HDMI”

function, see “About the BRAVIA Sync features (for HDMI connections only)”

(page 16).

, If you connect the player to a TV through an

AV amplifier (receiver) that is not compatible with the “Control for HDMI” function, you may be unable to control the

TV from the player.

No sound is output from the HDMI OUT jack.

, The HDMI OUT jack is connected to a DVI device (DVI jacks do not accept audio signals).

The sound is not output correctly when connected to the HDMI OUT jack.

, The device connected to the HDMI OUT jack does not support the audio format of the player. Check the audio settings

(page 45).

The display language on the screen switches automatically when connected to the HDMI OUT jack.

, When “Control for HDMI” is set to “On”

(page 50), the display language on the

screen automatically switches according to the language setting of the connected TV (if you change the setting on your TV, etc.).

56

The “Control for HDMI” function does not work (BRAVIA Sync).

, Check that the AC power cord of the connected component is securely connected.

, If the HDMI indicator does not appear in the front panel display, check the HDMI

connection (page 15, 20).

, Set “Control for HDMI” to “On” (page 50).

External memory (local storage)

The external memory is not recognized.

, Try the following: 1Turn the player off.

2

Align the V mark of the EXT slot with the V mark on the external memory, and

insert the external memory (page 23).

3

Turn the player on. 4Check that the

EXT indicator lights up in the front panel display.

Bonus contents or other data that are contained in a BD-ROM cannot be played.

, Try the following: 1Remove the disc.

2

Turn the player off. 3Remove and re-

insert the external memory (page 23).

4

Turn the player on. 5Check that the

EXT indicator lights up in the front panel display. 6Insert the BD-ROM with

BonusView.

A message indicating that the local storage does not have enough space appears on the screen.

, Delete unnecessary data in the external

memory (page 34).

Operation

The remote does not function.

, The batteries in the remote are weak

(page 26).

, The distance between the remote and the player is too far.

, The remote is not pointed at the remote sensor on the player.

The file name is not correctly displayed.

, The player can only display ISO 8859-1compliant character formats. Other character formats may be displayed differently.

, Depending on the writing software used, the input characters may be displayed differently.

The disc does not start playing from the beginning.

, Resume Play is on (page 32).

Some functions such as Stop or Search cannot be performed.

, Depending on the disc, you may not be able to do some of the operations above. Refer to the operating manual supplied with the disc.

The disc tray does not open and you cannot remove the disc even after you

press A.

, Try the following: 1Turn the player off, and disconnect the AC power cord.

2

Reconnect the AC power cord while pressing down A on the player. 3Keep pressing down A on the player until the tray opens. 4Remove the disc. 5When

“WAIT” appears in the front panel display, hold down [/1 on the player for more than

10 seconds until the player turns on again.

The player does not respond to any button.

, Moisture has condensed inside the player

(page 3).

, Hold down [/1 on the player for more than

10 seconds until the indicators in the front panel display turn off.

If the player still does not respond to any button, disconnect then reconnect the AC power cord.

The language for the soundtrack/subtitle or angles cannot be changed.

, Try using the BD’s or DVD’s menu instead of the direct selection button on the remote

(page 33).

, Multi-lingual tracks/subtitles or multiangles are not recorded on the BD or DVD being played.

, The BD or DVD prohibits the changing of the language for the sound track/subtitle or angles.

The disc tray does not open and

“LOCKED” or “TLK ON” appears in the front panel display.

, When “LOCKED” appears, the player is locked. To cancel the Child Lock, hold down X on the player until “UNLOCK”

appears in the front panel display (page 10).

, When “TLK ON” appears, contact your

Sony dealer or local authorized Sony service facility.

57

58

Self-Diagnosis Function

When the self-diagnosis function is activated to prevent the player from malfunctioning, an error code appears in the front panel display, or just appears without any messages on the entire screen.

In these cases, check the following.

When an error code appears in the front panel display

Error code Corrective action

Exxxx

SYS ERR

Contact your nearest Sony dealer or local authorized Sony service facility and give the error code.

FAN ERR • Check that the ventilation holes on the rear of the player are not blocked.

• Place the player in a location with adequate ventilation to prevent heat build-up in the player.

When just appears without any messages on the entire screen

Contact your nearest Sony dealer or local authorized Sony service facility.

Playable Discs

Type

Blu-ray Disc

DVD VIDEO

Disc Logo

Icon used in this manual

Characteristics

BD

BD-ROMs and BD-REs/BD-Rs in

BDMV and BDAV mode, including

8 cm discs (single layer) and DL discs

DVD

Discs such as movies that can be purchased or rented

DVD

DVD

DVD+RWs/DVD+Rs in +VR mode or

DVD-RWs/DVD-Rs in video and VR mode, including 8 cm discs (single layer) and DVD+R DL/DVD-R DL discs

DATA DVD DATA DVD

DVD+RWs/DVD+Rs/DVD-RWs/

DVD-Rs containing JPEG* image files

CD

DATA CD

CD

DATA CD

Music CDs or CD-Rs/CD-RWs in music

CD format

CD-Rs/CD-RWs containing JPEG* image files

* JPEG format conforming to UDF (Universal Disk

Format).

Notes about BD-ROM compatibility

Since the Blu-ray Disc specifications are new and evolving, some discs may not be playable depending on the disc type and the version.

The audio output differs depending on the source, connected output jack, and selected

audio settings. For details, see page 63.

,continued

59

60

Discs that cannot be played

• BDs with cartridge

• DVD-RAMs

• HD DVDs

• DVD Audio discs

• PHOTO CDs

• Data part of CD-Extras

• VCDs/Super VCDs

• HD layer on Super Audio CDs

• BD-ROMs/DVD VIDEOs with a different

region code (page 60).

• A disc recorded in a color system other than

NTSC, such as PAL (this player conforms to the NTSC color system).

Note on playback operations of BDs/DVDs

Some playback operations of BDs/DVDs may be intentionally set by software producers. Since this player plays BDs/

DVDs according to the disc contents the software producers designed, some playback features may not be available. Refer to the instructions supplied with the BDs/DVDs.

Region code (BD-ROM/DVD VIDEO only)

Your player has a region code printed on the rear of the unit and will only play BD-ROMs/

DVD VIDEOs (playback only) labeled with identical region codes. This system is used to protect copyrights.

DVD VIDEOs labeled

ALL

will also play on this player.

Depending on the BD-ROM/DVD VIDEO, no region code may be indicated even though playing the BD-ROM/DVD VIDEO is prohibited by area restrictions.

Region code

b

Notes about BD-REs/BD-Rs, DVD+RWs/

DVD+Rs, DVD-RWs/DVD-Rs, or CD-Rs/

CD-RWs

Some BD-REs/BD-Rs, DVD+RWs/DVD+Rs,

DVD-RWs/DVD-Rs, or CD-Rs/CD-RWs cannot be played on this player due to the recording quality or physical condition of the disc, or the characteristics of the recording device and authoring software.

A DVD disc will not play if it has not been correctly finalized. For more information, refer to the operating instructions supplied with the recording device. Note that some playback functions may not work with some DVD+RWs/

DVD+Rs, even if they have been correctly finalized. In this case, view the disc using normal playback.

Music discs encoded with copyright

protection technologies

This product is designed to play back discs that conform to the Compact Disc (CD) standard.

Various music discs encoded with copyright protection technologies are being marketed by some record companies. Please be aware that among those discs, there are some that do not conform to the CD standard and may not be playable by this product.

Note on DualDiscs

A DualDisc is a two sided disc product which mates DVD recorded material on one side with digital audio material on the other side.

However, since the audio material side does not conform to the Compact Disc (CD) standard, playback on this product is not guaranteed.

Note about double-layer DVDs

The playback pictures and sound may be momentarily interrupted when the layers switch.

Note about 8 cm BD-REs/8 cm BD-Rs

Some 8 cm BD-REs/8 cm BD-Rs cannot be played on this player.

Note about BD-REs/BD-Rs

This player supports Ver. 2.1 BD-RE and Ver. 1.1 and 1.2 BD-R including organic pigment type

BD-R (LTH type).

Note about DTS 5.1 MUSIC DISCs

This player can play DTS 5.1 MUSIC DISCs.

Audio signals are output in the formats specified

under the “Audio Output Signals” table on page

63.

About playback of discs recorded in

AVCHD format

This player can play AVCHD format discs.

TM

What is the AVCHD format?

The AVCHD format is a high-definition digital video camera format used to record SD (standard definition) or HD (high definition) signals of either the 1080i specification

*1

or the 720p specification

*2

on DVDs, using efficient data compression coding technology. The MPEG-4

AVC/H.264 format is adopted to compress video data, and the Dolby Digital or Linear PCM system is used to compress audio data. The MPEG-4 AVC/

H.264 format is capable of compressing images at higher efficiency than that of the conventional image compressing format. The MPEG-4 AVC/

H.264 format enables a high definition (HD) video signal shot on a digital video camera recorder to be recorded on DVD discs, in the same way as it would be for a standard definition (SD) television signal.

*1

A high-definition specification which utilizes

*2

1080 effective scanning lines and the interlace system.

A high-definition specification which utilizes

720 effective scanning lines and the progressive system.

b

• Some AVCHD format discs may not play, depending on the recording condition.

• The AVCHD format disc will not play if it has not been correctly finalized.

61

62

Video Output Resolution

Output resolution differs depending on the “Output Video Format” setting in the “Video

Settings” setup (page 42).

Resolution setting

480i

480p

720p

1080i

1080p

When “Output Video Format” is set to

“HDMI”

LINE OUT

VIDEO/

S VIDEO jack

COMPONENT

VIDEO jack

HDMI OUT jack

When “Output Video Format” is set to

“Component Video”

LINE OUT

VIDEO/

S VIDEO jack

COMPONENT

VIDEO jack

HDMI OUT jack

480i

480i

480i

480i

480i

480p

480i

480i

480i

480p

480i

480p

480i

480i no picture

480i

480i no picture

720p

1080i

1080p

480i

480i

720p*

1080i*

720p*

1080i* unselectable unselectable unselectable

* Protected contents on DVDs are output at 480p resolution.

When “Output Video Format” is set to

“Video or S Video”

480i video signals are output from the LINE

OUT VIDEO/S VIDEO or COMPONENT

VIDEO jack, and 480p video signals are output from the HDMI OUT jack.

Audio Output Signals

The audio output differs as follows, depending on the source, output jack, and the selected settings.

Analog

Disc/source

BD

Jacks/ settings

*1

Digital

HDMI OUT jack

*2

LPCM 2ch

LPCM 5.1ch

LPCM 7.1ch

Dolby Digital

Auto

*3

LPCM 2ch

LPCM 5.1ch

LPCM 7.1ch

LPCM 5.1ch

*5

2ch PCM

*3

LPCM 2ch

LPCM 2ch

LPCM 2ch

LPCM 2ch

Dolby Digital

Plus

Dolby TrueHD

DTS

LPCM 5.1ch

*5

(Dolby Digital)

LPCM 5.1ch

*5

(Dolby Digital)

LPCM 5.1ch

*5

LPCM 2ch

LPCM 2ch

LPCM 2ch

DIGITAL OUT (OPTICAL/

COAXIAL) jacks

*2

Bitstream

*4

PCM

LPCM 2ch

LPCM 2ch

LPCM 2ch

LPCM 2ch

LPCM 2ch LPCM 2ch

Dolby Digital/

LPCM 2ch

*6

Dolby Digital/

LPCM 2ch

*6

Dolby Digital/

LPCM 2ch

*6

DTS/

LPCM 2ch

*6

LPCM 2ch

LPCM 2ch

LPCM 2ch

LPCM 2ch

LINE OUT

(R-AUDIO-

L) jacks

2ch

2ch

2ch

2ch

2ch

2ch

2ch

DTS-HD High

Resolution

Audio

DTS-HD Master

Audio

DVD LPCM

Dolby Digital

CD

DTS

LPCM

DTS 5.1 MUSIC DISC

LPCM 5.1ch

*5

(DTS core)

LPCM 2ch

LPCM 5.1ch

(DTS core)

*5

LPCM 2ch

LPCM 2ch LPCM 2ch

Dolby Digital LPCM 2ch

DTS

LPCM 2ch

LPCM 2ch

LPCM 2ch

DTS LPCM 2ch

DTS/

LPCM 2ch

*6

LPCM 2ch

DTS/

LPCM 2ch

*6

LPCM 2ch

LPCM 2ch LPCM 2ch

Dolby Digital LPCM 2ch

DTS

LPCM 2ch

LPCM 2ch

LPCM 2ch

DTS LPCM 2ch

2ch

2ch

2ch

2ch

2ch

2ch

2ch

*1

When “Audio Output Priority” is set to “Stereo

*2

Analog,” LPCM 2ch signals are output from each jack.

When “Audio Output Priority” is set to “HDMI” or “Coaxial/Optical,” LPCM 2ch signals are

*3 output from jacks other than the selected jack.

Auto: when “Audio (HDMI)” is set to “Auto” in

*4

the “Audio Settings” setup (page 45).

2ch PCM: when “Audio (HDMI)” is set to “2ch

PCM” in the “Audio Settings” setup (page 45).

Bitstream: when “Dolby Digital” is set to

*5

“Dolby Digital” or “DTS” is set to “DTS” in the

“Audio Settings” setup (page 45).

When “BD Audio Setting” is set to “Direct,” audio recorded by the source is output by bitstream. However, this audio may be output as follows depending on the audio formats supported by the AV amplifier (receiver).

– When the AV amplifier (receiver) does not support HD Audio (Dolby Digital Plus, Dolby

TrueHD, DTS-HD High Resolution Audio and

DTS-HD Master Audio) but supports Multi-ch

LPCM, up to LPCM 7.1ch is output.

– When the AV amplifier (receiver) does not support HD Audio or Multi-ch LPCM but supports Dolby Digital/DTS, a Dolby Digital or DTS bitstream is output.

– When the AV amplifier (receiver) does not support HD Audio, Multi-ch LPCM or Dolby

Digital/DTS, LPCM 2ch is output.

*6

The 2-channel or less-channel primary/ secondary audio signals are output as LPCM 2ch signals.

b

When outputting 480i/480p video signals from the

HDMI OUT jack, Dolby TrueHD and DTS-HD

Master Audio are output as LPCM, Dolby Digital, or DTS bitstream signals even if “BD Audio

Setting” is set to “Direct” in the “Audio Settings”

setup (page 45).

63

64

Specifications

System

Laser: Semiconductor laser

Inputs and outputs

(Jack name:

Jack type/Output level/Load impedance)

LINE OUT R-AUDIO-L:

Phono jack/2 Vrms/10 kilohms

DIGITAL OUT (OPTICAL):

Optical output jack/–18 dBm

(wave length 660 nm)

DIGITAL OUT (COAXIAL):

Phono jack/0.5 Vp-p/75 ohms

HDMI OUT:

HDMI 19-pin standard connector

COMPONENT VIDEO OUT

(Y, P

B

, P

R

):

Phono jack/Y: 1.0 Vp-p/

P

B

, P

R

: 0.7 Vp-p/75 ohms

LINE OUT VIDEO:

Phono jack/1.0 Vp-p/75 ohms

LINE OUT S VIDEO:

4-pin mini DIN/

Y: 1.0 Vp-p, C: 0.286 Vp-p/75 ohms

LAN (100):

100BASE-TX Terminal

EXT:

External memory slot (For connecting the external memory)

DC output: 5 V 500 mA Max

General

Power requirements:

120 V AC, 60 Hz

Power consumption:

26 W

Dimensions (approx.):

430 mm × 220 mm × 60 mm

(17 in. × 8 3 /

4

in. × 2 3 /

8

in.)

(width/depth/height) incl. projecting parts

Mass (approx.):

2.9 kg (6

3

/

8

lb)

Operating temperature:

5 ºC to 35 ºC (41 °F to 95 °F)

Operating humidity:

25 % to 80 %

Supplied accessories

See page 13.

Specifications and design are subject to change without notice.

Language Code List

For details, see page 47.

The language spellings conform to the ISO 639: 1988 (E/F) standard.

Number, Language (BD Language Code/DVD Language Code)

not specified

Parental Control/Area Code

For details, see page 47.

Number, Area (Code)

2044, Argentina (ar)

2047, Australia (au)

2046, Austria (at)

2057, Belgium (be)

2070, Brazil (br)

2079, Canada (ca)

2090, Chile (cl)

2092, China (cn)

2093, Colombia (co)

2115, Denmark (dk)

2165, Finland (fi)

2174, France (fr)

2109, Germany (de)

2200, Greece (gr)

2219, Hong Kong (hk)

2248, India (in)

2238, Indonesia (id)

2239, Ireland (ie)

2254, Italy (it)

2276, Japan (jp)

2304, Korea (kr)

2333, Luxembourg (lu)

2363, Malaysia (my)

2362, Mexico (mx)

2376, Netherlands (nl)

2390, New Zealand (nz)

2379, Norway (no)

2427, Pakistan (pk)

2424, Philippines (ph)

2428, Poland (pl)

2436, Portugal (pt)

2489, Russia (ru)

2501, Singapore (sg)

2149, Spain (es)

2499, Sweden (se)

2086, Switzerland (ch)

2543, Taiwan (tw)

2528, Thailand (th)

2184, United Kingdom (gb)

65

Terms and Conditions of

Use and End User

License Agreement

66

The Sony Blu-ray Disc player (“Product”) and associated software (“Software”) are provided and maintained by Sony

Electronics Inc. and its affiliates (“Sony”). Sony also provides and maintains associated service (the “Service”), including any subsite accessible through the Service’s Internet homepage (the

“Site”). The Software includes software embedded in the

Product; stored on any media, bundled with the Product or otherwise provided by Sony; downloaded from the Site or otherwise made accessible or provided by Sony; any such media and any printed or “on-line” or electronic documentation associated with the Product and all updates and upgrades thereto.

WHEN YOU ACCESS, BROWSE, OR USE THE SERVICE,

PRODUCT, SOFTWARE, AND/OR SITE, YOU ACCEPT,

WITHOUT LIMITATION OR QUALIFICATION, THE

TERMS AND CONDITIONS SET FORTH HEREIN, SONY’S

PRIVACY POLICY POSTED ON THE SITE, AND ANY

ADDITIONAL TERMS AND CONDITIONS OF USE SET

FORTH IN ANY PORTION OF THE SERVICE AND SITE

(COLLECTIVELY THE “AGREEMENT”). IF YOU DO NOT

AGREE WITH THE TERMS AND CONDITIONS OF THIS

AGREEMENT, SONY DOES NOT GRANT THE LIMITED

RIGHTS HEREIN, AND PLEASE DO NOT USE THE

SERVICE, PRODUCT, SOFTWARE, AND/OR SITE.

1. Ownership

The Software and all materials on the Service and/or Site, including but not limited to images, software and text (the

“Content”) are protected by copyright under U.S. copyright law, international conventions, and other copyright laws. You cannot use the Software, Service, Product, Content, and Site except as specified herein. There may be proprietary logos, service marks, and trademarks found on this Service or Site. By making them available on the Service and/or Site, Sony is not granting you any license to utilize those proprietary logos, service marks, or trademarks. Any unauthorized use of the Service, Site, Content or Software may violate copyright laws, trademark laws, the laws of privacy and publicity, and civil and criminal statutes. All title and copyright in and to the Software or materials on the

Service/Site and any copies of the Software, are owned by Sony, its licensors, or suppliers. All rights not specifically granted under this Agreement are reserved by Sony, its licensors, and suppliers.

2. Your Rights & Limited License

The Service, Site, Software, Content, and Product are only for your personal use. You are responsible for all your activities hereunder, including all legal liability incurred from your use of the Service or others who use the Service via your Product or

Account (as defined below). You may use the Service, Site,

Software, Content and Product for lawful purposes only. You may not distribute, exchange, modify, sell, or transmit anything you may copy from the Service or Site, including but not limited to any text, images, audio, and video, for any business, commercial, or public purpose. As long as you comply with the terms of this Agreement, Sony grants you a non-exclusive, nontransferable, limited right to enter, display, and use the Service,

Site, and Software as set forth in this Agreement. You agree not to interrupt/disrupt or attempt to interrupt/disrupt the operation of this Service, Site or Software in any way.

3. User Account & Privacy

As part of your usage of the Product, Service, Site, and/or

Software, Sony may require that you establish a user account

(“Account”) for which you must provide Sony true, accurate, current, and complete information about yourself and maintain/ promptly update such information. You are responsible for maintaining the confidentiality of any and all of your passwords associated with the Account. You agree to notify Sony immediately of any unauthorized use of your password or any other breach of security related to the Service, Site, and/or

Software.

Sony’s Privacy Policy is posted on the Site and at

http://products.sel.sony.com/SEL/legal/privacy.html, the terms of which are incorporated herein, and applies to your use of the Account, Product, Service, Site, and Software.

4. Automatic Update

The Software contains a functionality by which it is updated automatically when the Product is connected to a server belonging to Sony or to a third party designated by Sony. When you specify your intention not to use this automatic update functionality, or when the setting asking whether you wish to update automatically is activated and you decline to execute updates, it is assumed that you agree that the security functionality improvements, error corrections, other functional updates or any other changes offered by Sony through such updates would not be made to the Software and that your current and further use of the Software may be affected thereby.

When the automatic update functionality described in the previous paragraph is activated, it is assumed that you agree (a) that the Software will be automatically updated as necessary to improve security functionality, to correct errors, to improve update functionality, or for other purposes, and (b) that this updating of the Software may be accompanied by the augmenting, modifying, or removing of functionality of the

Software.

5. Additional Terms Governing Product Software

You may use the Software solely in conjunction with the Product that accompanied the Software. The Software is licensed, not sold. In addition to the terms set forth in other portions of this

Agreement, the Software is subject to the following:

Use of Software. You may use the Software in conjunction with the Product for personal use.

Limitation on Reverse Engineering, Decompilation and

Disassembly. You may not modify, reverse engineer, decompile, or disassemble the Software in whole or in part.

Separation of Components.The Software is licensed as a single product. Its component parts may not be separated for use on more than one device unless expressly authorized by Sony.

Data Files. The Software may create data files automatically for use with the Software. Any such data files will be deemed as part of the Software.

Rental. You may not rent or lease the Software.

Software Transfer. You may permanently transfer all of your rights under this Agreement only as part of a sale or transfer of

Software accompanying the sale or transfer of your Product, provided you retain no copies, transfer all of the Software

(including all copies, component parts, the media and printed materials, all versions and any upgrades of the Software and this

Agreement), and the recipient agrees to the terms of this

Agreement.

Dependent Software. The software, network services or other products other than Software upon which the Software’s performance depends on might be interrupted or discontinued at the discretion of the suppliers (software suppliers, service providers or Sony).

High Risk Activities. The Software is not fault-tolerant and is not designed, manufactured or intended for use or resale as online control equipment in hazardous environments requiring failsafe performance, such as in the operation of nuclear facilities, aircraft navigation or communication systems, air traffic control, direct life support machines, or weapons systems, in which the failure of the Software could lead to death, personal injury, or severe physical or environmental damage (“High Risk

Activities”). Sony and its suppliers specifically disclaim any express or implied warranty of fitness for High Risk Activities.

U.S. Government Restricted Rights. The Software is provided with RESTRICTED RIGHTS. Use, duplication, or disclosure by the United States Government is subject to restriction as set forth in subparagraph (c) (1) and (2) of the Commercial Computer

Software-Restricted Rights at 48 CFR 52.227-19, as applicable.

Manufacturer is Sony Electronics Inc., 16530 Via Esprillo, San

Diego, CA 92127.

GNU General Public, Lesser General Public, & Other Licenses.

Notwithstanding terms in this Agreement, certain portions of the

Software are governed by the GNU Lesser General Public

License, Version 2.1 (LGPL), GNU General Public License

Version 2 (GPL), and other open source code licenses (“Open

Source Licenses”), copies of which are attached hereto and incorporated herein. For such portions of the Software, to the extent there is any conflict between this Agreement and the

Open Source Licenses, the Open Source Licenses shall govern as applicable.

Certain Source Code Availability. Sony is making available the source code of certain portions of the SOFTWARE per the GPL/

LGPL LICENSES. Please see http://www.sony.com/linux for access to and instructions on obtaining such source code.

6. Changes to Service

Sony reserves the right to discontinue one, some, or all of the features of the Service you receive at any time at its discretion.

Sony may, at its discretion and from time to time change, add or remove features and functionality, upgrade or modify the

Service, Site and/or Software without notice. You may, at

Sony’s discretion, receive messages regarding these changes and new features/functionality. Any new text, content, file, data, product, services, information, software, software tool or other feature provided by Sony (through the network or by CD-ROM or other means) (including, but not limited to, any update to

Software provided to you automatically pursuant to Section 4 of this Agreement) will be subject to this Agreement; provided that, if separate terms and conditions applicable to such feature are provided to you, such terms and conditions shall apply to such feature in priority to this Agreement.

7. Confidentiality

You shall maintain the confidentiality of any information with regard to the Product and Documentation that is provided under this Agreement and is not publicly known. You agree not to disclose such information to any third party without the prior written consent.

8. Sony’s Right to Terminate or Modify Terms or

Conditions of this Agreement

Sony may add to, change, or remove any part, term, or condition of this Agreement at any time, without prior notice. Any changes to this Agreement or any terms posted on the Service and/or Site apply as soon as they are posted. By continuing to use the

Service, Product, Software and/or Site after any changes are posted, you are indicating your acceptance of those changes.

SONY MAY ADD, CHANGE, DISCONTINUE, REMOVE,

OR SUSPEND ANY OTHER CONTENT POSTED ON THE

SERVICE AND/OR SITE, INCLUDING FEATURES AND

SPECIFICATIONS OF PRODUCTS DESCRIBED OR

DEPICTED ON THE SERVICE AND/OR SITE,

TEMPORARILY OR PERMANENTLY, AT ANY TIME,

WITHOUT NOTICE AND WITHOUT LIABILITY.

WITHOUT PREJUDICE TO ANY OTHER RIGHTS, SONY

MAY SUSPEND OR TERMINATE THIS AGREEMENT

IMMEDIATELY UPON NOTICE IF YOU FAIL TO

COMPLY WITH THE TERMS AND CONDITIONS OF THIS

AGREEMENT. Upon termination, you shall destroy the

Software within fourteen (14) days after the date of such termination, and upon Sony’s request, provide Sony with the certification of such destruction. Sony may take any legal and technical remedies to prevent the violation of and/or to enforce this Agreement, including without limitation, immediate termination of your access to the Service if we believe in our discretion you are violating this Agreement.

9. Indemnification

You agree to indemnify, defend, and hold Sony and all of its agents, directors, employees, information providers, licensors and licensees, affiliates, content providers, officers, and parent

(collectively, “Indemnified Parties”), harmless from and against any and all liability and costs (including, without limitation, attorneys’ fees and costs), incurred by the Indemnified Parties in connection with any claim arising out of (i) any breach or alleged breach by you of this Agreement in any manner, (ii) any information you submit to Sony hereunder, (iii) any breach or alleged breach by you of a third party’s rights or (iv) any damage caused by or alleged to have been caused by you to the Service.

You will cooperate as fully as reasonably required in

Indemnified Party(s) defense of any claim. Sony and/or

Indemnified Parties reserve the right, at its own expense, to assume the exclusive defense and control of any matter otherwise subject to indemnification by you and you shall not in any event settle any matter without the written consent of Sony and/or Indemnified Parties.

10. DISCLAIMER OF WARRANTIES AND DAMAGES;

LIMITATION OF LIABILITY

YOU UNDERSTAND THAT USAGE OF THE PRODUCT

AND SERVICE REQUIRES INTERNET SERVICE

PROVIDED BY YOU, FOR WHICH YOU ARE SOLELY

RESPONSIBLE. OPERATION OF THE PRODUCT AND/OR

SERVICE MAY BE LIMITED OR RESTRICTED

DEPENDING UPON THE CAPABILITIES OR TECHNICAL

LIMITATIONS OF YOUR INTERNET SERVICE.

YOUR USE OF THE SOFTWARE, SERVICE, PRODUCT,

CONTENT AND/OR SITE IS AT YOUR OWN RISK. THE

SOFTWARE, SERVICE, CONTENT AND SITE ARE

PROVIDED “AS IS” AND, TO THE FULLEST EXTENT

PERMISSIBLE BY LAW, SONY MAKES NO

REPRESENTATIONS OR WARRANTIES OF ANY KIND

WHATSOEVER (1) FOR THE ACCURACY,

MERCHANTABILITY, FITNESS FOR A PARTICULAR

PURPOSE, OR NON-INFRINGEMENT ASSOCIATED

WITH THE SERVICE, SITE, AND/OR SOFTWARE; (2)

THAT THE SERVER(S) THAT MAKES THE SERVICE,

SOFTWARE, AND/OR SITE AVAILABLE ARE FREE OF

VIRUSES OR OTHER COMPONENTS THAT MAY

INFECT, HARM, OR CAUSE DAMAGE TO YOUR

COMPUTER, TELEVISION, OTHER EQUIPMENT, OR

ANY OTHER PROPERTY. FURTHERMORE, SONY DOES

NOT WARRANT OR MAKE ANY REPRESENTATIONS

REGARDING THE USE OR THE RESULTS OF THE USE OF

THE SOFTWARE, SERVICE, AND/OR SITE IN TERMS OF

ITS CORRECTNESS, ACCURACY, RELIABILITY, OR

OTHERWISE. NO ORAL OR WRITTEN INFORMATION

OR ADVICE GIVEN BY SONY OR A SONY AUTHORIZED

REPRESENTATIVE SHALL CREATE A WARRANTY OR

IN ANY WAY INCREASE THE SCOPE OF THIS

WARRANTY. SHOULD THE SOFTWARE, SERVICE, AND/

OR SITE PROVE DEFECTIVE YOU (AND NOT SONY OR

A SONY AUTHORIZED REPRESENTATIVE) ASSUME

THE ENTIRE COST OF ALL NECESSARY SERVICING,

REPAIR OR CORRECTION.

UNDER NO CIRCUMSTANCES, INCLUDING BUT NOT

LIMITED TO SONY’S NEGLIGENCE OR ISSUES

RELATED TO THIRD PARTY CONTENT PROVIDERS,

SHALL SONY BE LIABLE FOR ANY CONSEQUENTIAL,

DIRECT, INCIDENTAL, INDIRECT, PUNITIVE, OR

SPECIAL DAMAGES RELATED TO (A) THE USE OF, (B)

THE INABILITY TO USE, OR (C) ERRORS OR OMISSIONS

IN THE SOFTWARE, SERVICE, PRODUCT, AND/OR SITE,

EVEN IF SONY OR AN AUTHORIZED REPRESENTATIVE

THEREOF HAS BEEN ADVISED OF THE POSSIBILITY OF

SUCH DAMAGES. SOME STATES DO NOT ALLOW THE

EXCLUSION OR LIMITATION OF CONSEQUENTIAL OR

INCIDENTAL DAMAGES, SO THE ABOVE LIMITATION

OR EXCLUSION MAY NOT APPLY TO YOU. IN NO

EVENT SHALL SONY’S TOTAL LIABILITY TO YOU FOR

ALL DAMAGES, LOSSES, AND CAUSES OF ACTION

(WHETHER IN CONTRACT OR TORT, INCLUDING, BUT

NOT LIMITED TO, NEGLIGENCE OR OTHERWISE)

EXCEED $100.00.

,continued

67

68

11. General Provisions

This Agreement, the limited warranty accompanying the

Product, plus any additional terms posted on the Service or Site, together constitute the entire agreement between Sony and you with respect to your use of the Product, Service, Site, Content, and Software. Any notice by Sony hereunder may be made by letter, email, or posting on the Service or Site. Any cause of action you may have with respect to your use of this Site must be commenced within one (1) year after the claim or cause of action arises. If for any reason a court of competent jurisdiction finds any provision of this Agreement, or portion thereof, to be unenforceable, that provision shall be enforced to the maximum extent permissible so as to affect the intent of this Agreement, and the remaining terms and conditions of the Agreement shall continue in full force and effect. This Agreement shall be governed by and construed in accordance with the laws of the

State of Delaware, United States of America, without reference to its conflicts of law rules. You agree to submit to the personal and exclusive jurisdiction of federal or state courts in Delaware.

Software License

Information

Required public statement & License for

GPL/LGPL licensed software used in this product

This product contains software that is subject to the following

GNU General Public License (“GPL”) or GNU Lesser General

Public License (“LGPL”). These establish that customers have the right to acquire, modify, and redistribute the source code of said software in accordance with the terms of the GPL or the

LGPL.

Package List

linux-kernel.tar.gz

pump lrzsz busybox gcc glibc netbase dosfstools lzo mkcramfs hostname scfs

The source code for the above-listed software is available on the

Web.

To download, please access the following URL: http://www.sony.net/Products/Linux

Please note that Sony cannot answer or respond to any inquiries regarding the content of this source code.

GNU GENERAL PUBLIC LICENSE

Version 2, June 1991

Copyright (C) 1989, 1991 Free Software Foundation, Inc.

51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA

Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed.

Preamble

The Licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU General

Public License is intended to guarantee your freedom to share and change free software--to make sure the software is free for all its users. This General Public License applies to most of the

Free Software Foundation’s software and to any other program whose authors commit to using it. (Some other Free Software

Foundation software is covered by the GNU Lesser General

Public License instead.) You can apply it to your programs, too.

When we speak of free software, we are referring to freedom, not price. Our General Public Licenses are designed to make sure that you have the freedom to distribute copies of free software

(and charge for this service if you wish), that you receive source code or can get it if you want it, that you can change the software or use pieces of it in new free programs; and that you know you can do these things.

To protect your rights, we need to make restrictions that forbid anyone to deny you these rights or to ask you to surrender the rights. These restrictions translate to certain responsibilities for you if you distribute copies of the software, or if you modify it.

For example, if you distribute copies of such a program, whether gratis or for a fee, you must give the recipients all the rights that you have. You must make sure that they, too, receive or can get the source code. And you must show them these terms so they know their rights.

We protect your rights with two steps: (1) copyright the software, and (2) offer you this license which gives you legal permission to copy, distribute and/or modify the software.

Also, for each author’s protection and ours, we want to make certain that everyone understands that there is no warranty for this free software. If the software is modified by someone else and passed on, we want its recipients to know that what they have is not the original, so that any problems introduced by others will not reflect on the original authors’ reputations.

Finally, any free program is threatened constantly by software patents. We wish to avoid the danger that redistributors of a free program will individually obtain patent licenses, in effect making the program proprietary. To prevent this, we have made it clear that any patent must be licensed for everyone’s free use or not licensed at all.

The precise terms and conditions for copying, distribution and modification follow.

GNU GENERAL PUBLIC LICENSE TERMS AND

CONDITIONS FOR COPYING, DISTRIBUTION AND

MODIFICATION

0. This License applies to any program or other work which contains a notice placed by the copyright holder saying it may be distributed under the terms of this General Public

License. The “Program”, below, refers to any such program or work, and a “work based on the Program” means either the

Program or any derivative work under copyright law: that is to say, a work containing the Program or a portion of it, either verbatim or with modifications and/or translated into another language. (Hereinafter, translation is included without limitation in the term “modification”.) Each licensee is addressed as “you”.

Activities other than copying, distribution and modification are not covered by this License; they are outside its scope. The act of running the Program is not restricted, and the output from the

Program is covered only if its contents constitute a work based on the Program (independent of having been made by running the Program). Whether that is true depends on what the Program does.

1. You may copy and distribute verbatim copies of the

Program’s source code as you receive it, in any medium, provided that you conspicuously and appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty; keep intact all the notices that refer to this

License and to the absence of any warranty; and give any other recipients of the Program a copy of this License along with the Program.

You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange for a fee.

2. You may modify your copy or copies of the Program or any portion of it, thus forming a work based on the Program, and copy and distribute such modifications or work under the terms of Section 1 above, provided that you also meet all of these conditions: a) You must cause the modified files to carry prominent notices stating that you changed the files and the date of any change.

b) You must cause any work that you distribute or publish, that in whole or in part contains or is derived from the

Program or any part thereof, to be licensed as a whole at no charge to all third parties under the terms of this

License.

c) If the modified program normally reads commands interactively when run, you must cause it, when started running for such interactive use in the most ordinary way, to print or display an announcement including an appropriate copyright notice and a notice that there is no warranty (or else, saying that you provide a warranty) and that users may redistribute the program under these conditions, and telling the user how to view a copy of this

License. (Exception: if the Program itself is interactive but does not normally print such an announcement, your work based on the Program is not required to print an announcement.)

These requirements apply to the modified work as a whole. If identifiable sections of that work are not derived from the

Program, and can be reasonably considered independent and separate works in themselves, then this License, and its terms, do not apply to those sections when you distribute them as separate works. But when you distribute the same sections as part of a whole which is a work based on the Program, the distribution of the whole must be on the terms of this License, whose permissions for other licensees extend to the entire whole, and thus to each and every part regardless of who wrote it.

Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you; rather, the intent is to exercise the right to control the distribution of derivative or collective works based on the Program.

In addition, mere aggregation of another work not based on the

Program with the Program (or with a work based on the

Program) on a volume of a storage or distribution medium does not bring the other work under the scope of this License.

3. You may copy and distribute the Program (or a work based on it, under Section 2) in object code or executable form under the terms of Sections 1 and 2 above provided that you also do one of the following: a) Accompany it with the complete corresponding machinereadable source code, which must be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange; or, b) Accompany it with a written offer, valid for at least three years, to give any third party, for a charge no more than your cost of physically performing source distribution, a complete machine-readable copy of the corresponding source code, to be distributed under the terms of Sections

1 and 2 above on a medium customarily used for software interchange; or, c) Accompany it with the information you received as to the offer to distribute corresponding source code. (This alternative is allowed only for noncommercial distribution and only if you received the program in object code or executable form with such an offer, in accord with Subsection b above.)

The source code for a work means the preferred form of the work for making modifications to it. For an executable work, complete source code means all the source code for all modules it contains, plus any associated interface definition files, plus the scripts used to control compilation and installation of the executable. However, as a special exception, the source code distributed need not include anything that is normally distributed

(in either source or binary form) with the major components

(compiler, kernel, and so on) of the operating system on which the executable runs, unless that component itself accompanies the executable.

If distribution of executable or object code is made by offering access to copy from a designated place, then offering equivalent access to copy the source code from the same place counts as distribution of the source code, even though third parties are not compelled to copy the source along with the object code.

4. You may not copy, modify, sublicense, or distribute the

Program except as expressly provided under this License.

Any attempt otherwise to copy, modify, sublicense or distribute the Program is void, and will automatically terminate your rights under this License. However, parties who have received copies, or rights, from you under this

License will not have their licenses terminated so long as such parties remain in full compliance.

5. You are not required to accept this License, since you have not signed it. However, nothing else grants you permission to modify or distribute the Program or its derivative works.

These actions are prohibited by law if you do not accept this

License. Therefore, by modifying or distributing the

Program (or any work based on the Program), you indicate your acceptance of this License to do so, and all its terms and conditions for copying, distributing or modifying the

Program or works based on it.

,continued

69

70

6. Each time you redistribute the Program (or any work based on the Program), the recipient automatically receives a license from the original licensor to copy, distribute or modify the Program subject to these terms and conditions.

You may not impose any further restrictions on the recipients’ exercise of the rights granted herein. You are not responsible for enforcing compliance by third parties to this

License.

7. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited to patent issues), conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this License, they do not excuse you from the conditions of this License. If you cannot distribute so as to satisfy simultaneously your obligations under this License and any other pertinent obligations, then as a consequence you may not distribute the Program at all. For example, if a patent license would not permit royalty-free redistribution of the Program by all those who receive copies directly or indirectly through you, then the only way you could satisfy both it and this License would be to refrain entirely from distribution of the Program.

If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is intended to apply and the section as a whole is intended to apply in other circumstances.

It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity of any such claims; this section has the sole purpose of protecting the integrity of the free software distribution system, which is implemented by public license practices. Many people have made generous contributions to the wide range of software distributed through that system in reliance on consistent application of that system; it is up to the author/donor to decide if he or she is willing to distribute software through any other system and a licensee cannot impose that choice.

This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this License.

8. If the distribution and/or use of the Program is restricted in certain countries either by patents or by copyrighted interfaces, the original copyright holder who places the

Program under this License may add an explicit geographical distribution limitation excluding those countries, so that distribution is permitted only in or among countries not thus excluded. In such case, this License incorporates the limitation as if written in the body of this License.

9. The Free Software Foundation may publish revised and/or new versions of the General Public License from time to time. Such new versions will be similar in spirit to the present version, but may differ in detail to address new problems or concerns.

Each version is given a distinguishing version number. If the

Program specifies a version number of this License which applies to it and “any later version”, you have the option of following the terms and conditions either of that version or of any later version published by the Free Software Foundation. If the Program does not specify a version number of this License, you may choose any version ever published by the Free Software

Foundation.

10. If you wish to incorporate parts of the Program into other free programs whose distribution conditions are different, write to the author to ask for permission. For software which is copyrighted by the Free Software Foundation, write to the

Free Software Foundation; we sometimes make exceptions for this. Our decision will be guided by the two goals of preserving the free status of all derivatives of our free software and of promoting the sharing and reuse of software generally.

NO WARRANTY

11. BECAUSE THE PROGRAM IS LICENSED FREE OF

CHARGE, THERE IS NO WARRANTY FOR THE

PROGRAM, TO THE EXTENT PERMITTED BY

APPLICABLE LAW. EXCEPT WHEN OTHERWISE

STATED IN WRITING THE COPYRIGHT HOLDERS

AND/OR OTHER PARTIES PROVIDE THE PROGRAM

“AS IS” WITHOUT WARRANTY OF ANY KIND,

EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT

NOT LIMITED TO, THE IMPLIED WARRANTIES OF

MERCHANTABILITY AND FITNESS FOR A

PARTICULAR PURPOSE. THE ENTIRE RISK AS TO

THE QUALITY AND PERFORMANCE OF THE

PROGRAM IS WITH YOU. SHOULD THE PROGRAM

PROVE DEFECTIVE, YOU ASSUME THE COST OF

ALL NECESSARY SERVICING, REPAIR OR

CORRECTION.

12. IN NO EVENT UNLESS REQUIRED BY APPLICABLE

LAW OR AGREED TO IN WRITING WILL ANY

COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO

MAY MODIFY AND/OR REDISTRIBUTE THE

PROGRAM AS PERMITTED ABOVE, BE LIABLE TO

YOU FOR DAMAGES, INCLUDING ANY GENERAL,

SPECIAL, INCIDENTAL OR CONSEQUENTIAL

DAMAGES ARISING OUT OF THE USE OR INABILITY

TO USE THE PROGRAM (INCLUDING BUT NOT

LIMITED TO LOSS OF DATA OR DATA BEING

RENDERED INACCURATE OR LOSSES SUSTAINED

BY YOU OR THIRD PARTIES OR A FAILURE OF THE

PROGRAM TO OPERATE WITH ANY OTHER

PROGRAMS), EVEN IF SUCH HOLDER OR OTHER

PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF

SUCH DAMAGES.

END OF TERMS AND CONDITIONS

How to Apply These Terms to Your New Programs

If you develop a new program, and you want it to be of the greatest possible use to the public, the best way to achieve this is to make it free software which everyone can redistribute and change under these terms.

To do so, attach the following notices to the program. It is safest to attach them to the start of each source file to most effectively convey the exclusion of warranty; and each file should have at least the “copyright” line and a pointer to where the full notice is found.

<one line to give the program’s name and an idea of what it does.>

Copyright (C) <year> <name of author>

This program is free software; you can redistribute it and/or modify it under the terms of the GNU General Public License as published by the Free Software Foundation; either version 2 of the License, or (at your option) any later version.

This program is distributed in the hope that it will be useful, but

WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A

PARTICULAR PURPOSE. See the GNU General Public

License for more details.

You should have received a copy of the GNU General Public

License along with this program; if not, write to the Free

Software Foundation, Inc., 59 Temple Place - Suite 330, Boston,

MA 02111-1307, USA.

Also add information on how to contact you by electronic and paper mail.

If the program is interactive, make it output a short notice like this when it starts in an interactive mode:

Gnomovision version 69, Copyright (C) year name of author

Gnomovision comes with ABSOLUTELY NO WARRANTY; for details type ‘show w’. This is free software, and you are welcome to redistribute it under certain conditions; type ‘show c’ for details.

The hypothetical commands ‘show w’ and ‘show c’ should show the appropriate parts of the General Public License. Of course, the commands you use may be called something other than

‘show w’ and ‘show c’; they could even be mouse-clicks or menu items--whatever suits your program.

You should also get your employer (if you work as a programmer) or your school, if any, to sign a “copyright disclaimer” for the program, if necessary. Here is a sample; alter the names:

Yoyodyne, Inc., hereby disclaims all copyright interest in the program ‘Gnomovision’ (which makes passes at compilers) written by James Hacker.

<signature of Ty Coon>, 1 April 1989

Ty Coon, President of Vice

This General Public License does not permit incorporating your program into proprietary programs. If your program is a subroutine library, you may consider it more useful to permit linking proprietary applications with the library. If this is what you want to do, use the GNU Lesser General Public License instead of this License.

GNU LESSER GENERAL PUBLIC

LICENSE

Version 2.1, February 1999

Copyright (C) 1991, 1999 Free Software Foundation, Inc.

51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA

Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed.

[This is the first released version of the Lesser GPL. It also counts as the successor of the GNU Library Public License, version 2, hence the version number 2.1.]

Preamble

The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU General

Public Licenses are intended to guarantee your freedom to share and change free software--to make sure the software is free for all its users.

This license, the Lesser General Public License, applies to some specially designated software packages--typically libraries--of the Free Software Foundation and other authors who decide to use it. You can use it too, but we suggest you first think carefully about whether this license or the ordinary General Public

License is the better strategy to use in any particular case, based on the explanations below.

When we speak of free software, we are referring to freedom of use, not price. Our General Public Licenses are designed to make sure that you have the freedom to distribute copies of free software (and charge for this service if you wish); that you receive source code or can get it if you want it; that you can change the software and use pieces of it in new free programs; and that you are informed that you can do these things.

To protect your rights, we need to make restrictions that forbid distributors to deny you these rights or to ask you to surrender these rights. These restrictions translate to certain responsibilities for you if you distribute copies of the library or if you modify it.

For example, if you distribute copies of the library, whether gratis or for a fee, you must give the recipients all the rights that we gave you. You must make sure that they, too, receive or can get the source code. If you link other code with the library, you must provide complete object files to the recipients, so that they can relink them with the library after making changes to the library and recompiling it. And you must show them these terms so they know their rights.

We protect your rights with a two-step method: (1) we copyright the library, and (2) we offer you this license, which gives you legal permission to copy, distribute and/or modify the library.

To protect each distributor, we want to make it very clear that there is no warranty for the free library. Also, if the library is modified by someone else and passed on, the recipients should know that what they have is not the original version, so that the original author's reputation will not be affected by problems that might be introduced by others.

Finally, software patents pose a constant threat to the existence of any free program. We wish to make sure that a company cannot effectively restrict the users of a free program by obtaining a restrictive license from a patent holder. Therefore, we insist that any patent license obtained for a version of the library must be consistent with the full freedom of use specified in this license.

Most GNU software, including some libraries, is covered by the ordinary GNU General Public License. This license, the GNU

Lesser General Public License, applies to certain designated libraries, and is quite different from the ordinary General Public

License. We use this license for certain libraries in order to permit linking those libraries into non-free programs.

When a program is linked with a library, whether statically or using a shared library, the combination of the two is legally speaking a combined work, a derivative of the original library.

The ordinary General Public License therefore permits such linking only if the entire combination fits its criteria of freedom.

The Lesser General Public License permits more lax criteria for linking other code with the library.

We call this license the “Lesser” General Public License because it does Less to protect the user’s freedom than the ordinary

General Public License. It also provides other free software developers Less of an advantage over competing non-free programs. These disadvantages are the reason we use the ordinary General Public License for many libraries. However, the Lesser license provides advantages in certain special circumstances.

For example, on rare occasions, there may be a special need to encourage the widest possible use of a certain library, so that it becomes a de-facto standard. To achieve this, non-free programs must be allowed to use the library. A more frequent case is that a free library does the same job as widely used non-free libraries.

In this case, there is little to gain by limiting the free library to free software only, so we use the Lesser General Public License.

In other cases, permission to use a particular library in non-free programs enables a greater number of people to use a large body of free software. For example, permission to use the GNU C

Library in non-free programs enables many more people to use the whole GNU operating system, as well as its variant, the

GNU/Linux operating system.

Although the Lesser General Public License is Less protective of the users’ freedom, it does ensure that the user of a program that is linked with the Library has the freedom and the wherewithal to run that program using a modified version of the Library.

The precise terms and conditions for copying, distribution and modification follow. Pay close attention to the difference between a “work based on the library” and a “work that uses the library”. The former contains code derived from the library, whereas the latter must be combined with the library in order to run.

GNU GENERAL PUBLIC LICENSE TERMS AND

CONDITIONS FOR COPYING, DISTRIBUTION AND

MODIFICATION

0. This License Agreement applies to any software library or other program which contains a notice placed by the copyright holder or other authorized party saying it may be distributed under the terms of this Lesser General Public

License (also called “this License”). Each licensee is addressed as “you”.

A “library” means a collection of software functions and/or data prepared so as to be conveniently linked with application programs (which use some of those functions and data) to form executables.

,continued

71

72

The “Library”, below, refers to any such software library or work which has been distributed under these terms. A “work based on the Library” means either the Library or any derivative work under copyright law: that is to say, a work containing the

Library or a portion of it, either verbatim or with modifications and/or translated straightforwardly into another language.

(Hereinafter, translation is included without limitation in the term “modification”.)

“Source code” for a work means the preferred form of the work for making modifications to it. For a library, complete source code means all the source code for all modules it contains, plus any associated interface definition files, plus the scripts used to control compilation and installation of the library.

Activities other than copying, distribution and modification are not covered by this License; they are outside its scope. The act of running a program using the Library is not restricted, and output from such a program is covered only if its contents constitute a work based on the Library (independent of the use of the Library in a tool for writing it). Whether that is true depends on what the Library does and what the program that uses the Library does.

1. You may copy and distribute verbatim copies of the

Library’s complete source code as you receive it, in any medium, provided that you conspicuously and appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty; keep intact all the notices that refer to this License and to the absence of any warranty; and distribute a copy of this License along with the Library.

You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange for a fee.

2. You may modify your copy or copies of the Library or any portion of it, thus forming a work based on the Library, and copy and distribute such modifications or work under the terms of Section 1 above, provided that you also meet all of these conditions: a) The modified work must itself be a software library. b) You must cause the files modified to carry prominent notices stating that you changed the files and the date of any change. c) You must cause the whole of the work to be licensed at no charge to all third parties under the terms of this

License.

d) If a facility in the modified Library refers to a function or a table of data to be supplied by an application program that uses the facility, other than as an argument passed when the facility is invoked, then you must make a good faith effort to ensure that, in the event an application does not supply such function or table, the facility still operates, and performs whatever part of its purpose remains meaningful.

(For example, a function in a library to compute square roots has a purpose that is entirely well-defined independent of the application. Therefore, Subsection 2d requires that any application-supplied function or table used by this function must be optional: if the application does not supply it, the square root function must still compute square roots.)

These requirements apply to the modified work as a whole.

If identifiable sections of that work are not derived from the

Library, and can be reasonably considered independent and separate works in themselves, then this License, and its terms, do not apply to those sections when you distribute them as separate works. But when you distribute the same sections as part of a whole which is a work based on the

Library, the distribution of the whole must be on the terms of this License, whose permissions for other licensees extend to the entire whole, and thus to each and every part regardless of who wrote it.

Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you; rather, the intent is to exercise the right to control the distribution of derivative or collective works based on the Library.

In addition, mere aggregation of another work not based on the

Library with the Library (or with a work based on the Library) on a volume of a storage or distribution medium does not bring the other work under the scope of this License.

3. You may opt to apply the terms of the ordinary GNU General

Public License instead of this License to a given copy of the

Library. To do this, you must alter all the notices that refer to this License, so that they refer to the ordinary GNU General

Public License, version 2, instead of to this License. (If a newer version than version 2 of the ordinary GNU General

Public License has appeared, then you can specify that version instead if you wish.) Do not make any other change in these notices.

Once this change is made in a given copy, it is irreversible for that copy, so the ordinary GNU General Public License applies to all subsequent copies and derivative works made from that copy.

This option is useful when you wish to copy part of the code of the Library into a program that is not a library.

4. You may copy and distribute the Library (or a portion or derivative of it, under Section 2) in object code or executable form under the terms of Sections 1 and 2 above provided that you accompany it with the complete corresponding machinereadable source code, which must be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange.

If distribution of object code is made by offering access to copy from a designated place, then offering equivalent access to copy the source code from the same place satisfies the requirement to distribute the source code, even though third parties are not compelled to copy the source along with the object code.

5. A program that contains no derivative of any portion of the

Library, but is designed to work with the Library by being compiled or linked with it, is called a “work that uses the

Library”. Such a work, in isolation, is not a derivative work of the Library, and therefore falls outside the scope of this

License.

However, linking a “work that uses the Library” with the Library creates an executable that is a derivative of the Library (because it contains portions of the Library), rather than a “work that uses the library”. The executable is therefore covered by this License.

Section 6 states terms for distribution of such executables.

When a “work that uses the Library” uses material from a header file that is part of the Library, the object code for the work may be a derivative work of the Library even though the source code is not. Whether this is true is especially significant if the work can be linked without the Library, or if the work is itself a library. The threshold for this to be true is not precisely defined by law.

If such an object file uses only numerical parameters, data structure layouts and assessors, and small macros and small inline functions (ten lines or less in length), then the use of the object file is unrestricted, regardless of whether it is legally a derivative work. (Executables containing this object code plus portions of the Library will still fall under Section 6.)

Otherwise, if the work is a derivative of the Library, you may distribute the object code for the work under the terms of Section

6. Any executables containing that work also fall under Section

6, whether or not they are linked directly with the Library itself.

6. As an exception to the Sections above, you may also combine or link a “work that uses the Library” with the

Library to produce a work containing portions of the Library, and distribute that work under terms of your choice, provided that the terms permit modification of the work for the customer’s own use and reverse engineering for debugging such modifications.

You must give prominent notice with each copy of the work that the Library is used in it and that the Library and its use are covered by this License. You must supply a copy of this License.

If the work during execution displays copyright notices, you must include the copyright notice for the Library among them, as well as a reference directing the user to the copy of this

License. Also, you must do one of these things: a) Accompany the work with the complete corresponding machine-readable source code for the Library including whatever changes were used in the work (which must be distributed under Sections 1 and 2 above); and, if the work is an executable linked with the Library, with the complete machine-readable “work that uses the Library”, as object code and/or source code, so that the user can modify the Library and then relink to produce a modified executable containing the modified Library. (It is understood that the user who changes the contents of definitions files in the Library will not necessarily be able to recompile the application to use the modified definitions.) b) Use a suitable shared library mechanism for linking with the Library. A suitable mechanism is one that (1) uses at run time a copy of the library already present on the user's computer system, rather than copying library functions into the executable, and (2) will operate properly with a modified version of the library, if the user installs one, as long as the modified version is interface-compatible with the version that the work was made with. c) Accompany the work with a written offer, valid for at least three years, to give the same user the materials specified in Subsection 6a, above, for a charge no more than the cost of performing this distribution. d) If distribution of the work is made by offering access to copy from a designated place, offer equivalent access to copy the above specified materials from the same place. e) Verify that the user has already received a copy of these materials or that you have already sent this user a copy.

For an executable, the required form of the “work that uses the

Library” must include any data and utility programs needed for reproducing the executable from it. However, as a special exception, the materials to be distributed need not include anything that is normally distributed (in either source or binary form) with the major components (compiler, kernel, and so on) of the operating system on which the executable runs, unless that component itself accompanies the executable.

It may happen that this requirement contradicts the license restrictions of other proprietary libraries that do not normally accompany the operating system. Such a contradiction means you cannot use both them and the Library together in an executable that you distribute.

7. You may place library facilities that are a work based on the

Library side-by-side in a single library together with other library facilities not covered by this License, and distribute such a combined library, provided that the separate distribution of the work based on the Library and of the other library facilities is otherwise permitted, and provided that you do these two things: a) Accompany the combined library with a copy of the same work based on the Library, uncombined with any other library facilities. This must be distributed under the terms of the Sections above. b) Give prominent notice with the combined library of the fact that part of it is a work based on the Library, and explaining where to find the accompanying uncombined form of the same work.

8. You may not copy, modify, sublicense, link with, or distribute the Library except as expressly provided under this

License. Any attempt otherwise to copy, modify, sublicense, link with, or distribute the Library is void, and will automatically terminate your rights under this License.

However, parties who have received copies, or rights, from you under this License will not have their licenses terminated so long as such parties remain in full compliance.

9. You are not required to accept this License, since you have not signed it. However, nothing else grants you permission to modify or distribute the Library or its derivative works.

These actions are prohibited by law if you do not accept this

License. Therefore, by modifying or distributing the Library

(or any work based on the Library), you indicate your acceptance of this License to do so, and all its terms and conditions for copying, distributing or modifying the Library or works based on it.

10. Each time you redistribute the Library (or any work based on the Library), the recipient automatically receives a license from the original licensor to copy, distribute, link with or modify the Library subject to these terms and conditions.

You may not impose any further restrictions on the recipients' exercise of the rights granted herein. You are not responsible for enforcing compliance by third parties with this License.

11. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited to patent issues), conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this License, they do not excuse you from the conditions of this License. If you cannot distribute so as to satisfy simultaneously your obligations under this License and any other pertinent obligations, then as a consequence you may not distribute the Library at all. For example, if a patent license would not permit royalty-free redistribution of the Library by all those who receive copies directly or indirectly through you, then the only way you could satisfy both it and this License would be to refrain entirely from distribution of the Library.

If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is intended to apply, and the section as a whole is intended to apply in other circumstances.

It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity of any such claims; this section has the sole purpose of protecting the integrity of the free software distribution system which is implemented by public license practices. Many people have made generous contributions to the wide range of software distributed through that system in reliance on consistent application of that system; it is up to the author/donor to decide if he or she is willing to distribute software through any other system and a licensee cannot impose that choice.

This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this License.

12. If the distribution and/or use of the Library is restricted in certain countries either by patents or by copyrighted interfaces, the original copyright holder who places the

Library under this License may add an explicit geographical distribution limitation excluding those countries, so that distribution is permitted only in or among countries not thus excluded. In such case, this License incorporates the limitation as if written in the body of this License.

13. The Free Software Foundation may publish revised and/or new versions of the Lesser General Public License from time to time. Such new versions will be similar in spirit to the present version, but may differ in detail to address new problems or concerns.

Each version is given a distinguishing version number. If the

Library specifies a version number of this License which applies to it and “any later version”, you have the option of following the terms and conditions either of that version or of any later version published by the Free Software Foundation. If the Library does not specify a license version number, you may choose any version ever published by the Free Software Foundation.

,continued

73

74

14. If you wish to incorporate parts of the Library into other free programs whose distribution conditions are incompatible with these, write to the author to ask for permission. For software which is copyrighted by the Free Software

Foundation, write to the Free Software Foundation; we sometimes make exceptions for this. Our decision will be guided by the two goals of preserving the free status of all derivatives of our free software and of promoting the sharing and reuse of software generally.

NO WARRANTY

15. BECAUSE THE LIBRARY IS LICENSED FREE OF

CHARGE, THERE IS NO WARRANTY FOR THE

LIBRARY, TO THE EXTENT PERMITTED BY

APPLICABLE LAW. EXCEPT WHEN OTHERWISE

STATED IN WRITING THE COPYRIGHT HOLDERS

AND/OR OTHER PARTIES PROVIDE THE LIBRARY

“AS IS” WITHOUT WARRANTY OF ANY KIND,

EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT

NOT LIMITED TO, THE IMPLIED WARRANTIES OF

MERCHANTABILITY AND FITNESS FOR A

PARTICULAR PURPOSE. THE ENTIRE RISK AS TO

THE QUALITY AND PERFORMANCE OF THE

LIBRARY IS WITH YOU. SHOULD THE LIBRARY

PROVE DEFECTIVE, YOU ASSUME THE COST OF

ALL NECESSARY SERVICING, REPAIR OR

CORRECTION.

16. IN NO EVENT UNLESS REQUIRED BY APPLICABLE

LAW OR AGREED TO IN WRITING WILL ANY

COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO

MAY MODIFY AND/OR REDISTRIBUTE THE

LIBRARY AS PERMITTED ABOVE, BE LIABLE TO

YOU FOR DAMAGES, INCLUDING ANY GENERAL,

SPECIAL, INCIDENTAL OR CONSEQUENTIAL

DAMAGES ARISING OUT OF THE USE OR INABILITY

TO USE THE LIBRARY (INCLUDING BUT NOT

LIMITED TO LOSS OF DATA OR DATA BEING

RENDERED INACCURATE OR LOSSES SUSTAINED

BY YOU OR THIRD PARTIES OR A FAILURE OF THE

LIBRARY TO OPERATE WITH ANY OTHER

SOFTWARE), EVEN IF SUCH HOLDER OR OTHER

PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF

SUCH DAMAGES.

END OF TERMS AND CONDITIONS

How to Apply These Terms to Your New Libraries

If you develop a new library, and you want it to be of the greatest possible use to the public, we recommend making it free software that everyone can redistribute and change. You can do so by permitting redistribution under these terms (or, alternatively, under the terms of the ordinary General Public

License).

To apply these terms, attach the following notices to the library.

It is safest to attach them to the start of each source file to most effectively convey the exclusion of warranty; and each file should have at least the “copyright” line and a pointer to where the full notice is found.

<one line to give the library's name and an idea of what it does.>

Copyright (C) <year> <name of author>

This library is free software; you can redistribute it and/or modify it under the terms of the GNU Lesser General Public

License as published by the Free Software Foundation; either version 2.1 of the License, or (at your option) any later version.

This library is distributed in the hope that it will be useful, but

WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A

PARTICULAR PURPOSE. See the GNU Lesser General

Public License for more details.

You should have received a copy of the GNU Lesser General

Public License along with this library; if not, write to the Free

Software Foundation, Inc., 59 Temple Place, Suite 330, Boston,

MA 02111-1307 USA

Also add information on how to contact you by electronic and paper mail.

You should also get your employer (if you work as a programmer) or your school, if any, to sign a “copyright disclaimer” for the library, if necessary. Here is a sample; alter the names:

Yoyodyne, Inc., hereby disclaims all copyright interest in the library ‘Frob’ (a library for tweaking knobs) written by James

Random Hacker.

signature of Ty Coon, 1 April 1990

Ty Coon, President of Vice

That’s all there is to it!

Required statements for OpenSSL project used in this product

This product contains OpenSSL (including the library Original

SSLeay), which Sony uses under license with the copyright holder. In compliance with a request by the copyright holder of said software, Sony conveys the following notice and asks that you read it.

Package name: sony-target-grel-openssl-0.9.8g-020201.src.rpm

OpenSSL

Copyright (c) 1998-2006 The OpenSSL Project. All rights reserved.

Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:

1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.

2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.

3. All advertising materials mentioning features or use of this software must display the following acknowledgment:

“This product includes software developed by the OpenSSL

Project for use in the OpenSSL Toolkit. (http:// www.openssl.org/)”

4. The names “OpenSSL Toolkit” and “OpenSSL Project” must not be used to endorse or promote products derived from this software without prior written permission. For written permission, please contact [email protected].

5. Products derived from this software may not be called

“OpenSSL” nor may “OpenSSL” appear in their names without prior written permission of the OpenSSL Project.

6. Redistributions of any form whatsoever must retain the following acknowledgment:

“This product includes software developed by the OpenSSL

Project for use in the OpenSSL Toolkit (http:// www.openssl.org/)”

THIS SOFTWARE IS PROVIDED BY THE OpenSSL

PROJECT “AS IS” AND ANY EXPRESSED OR IMPLIED

WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE

IMPLIED WARRANTIES OF MERCHANTABILITY AND

FITNESS FOR A PARTICULAR PURPOSE ARE

DISCLAIMED. IN NO EVENT SHALL THE OpenSSL

PROJECT OR ITS CONTRIBUTORS BE LIABLE FOR ANY

DIRECT, INDIRECT, INCIDENTAL, SPECIAL,

EXEMPLARY, OR CONSEQUENTIAL DAMAGES

(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT

OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,

DATA, OR PROFITS; OR BUSINESS INTERRUPTION)

HOWEVER CAUSED AND ON ANY THEORY OF

LIABILITY, WHETHER IN CONTRACT, STRICT

LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR

OTHERWISE)

ARISING IN ANY WAY OUT OF THE USE OF THIS

SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF

SUCH DAMAGE.

This product includes cryptographic software written by Eric

Young ([email protected]). This product includes software written by Tim Hudson ([email protected]).

Original SSLeay License

Original SSLeay

Copyright (C) 1995-1998 Eric Young ([email protected])

All rights reserved.

This package is an SSL implementation written by Eric Young

([email protected]).

The implementation was written so as to conform with

Netscapes SSL.

This library is free for commercial and non-commercial use as long as the following conditions are aheared to. The following conditions apply to all code found in this distribution, be it the

RC4, RSA, lhash, DES, etc., code; not just the SSL code. The

SSL documentation included with this distribution is covered by the same copyright terms except that the holder is Tim Hudson

([email protected]).

Copyright remains Eric Young’s, and as such any Copyright notices in the code are not to be removed.

If this package is used in a product, Eric Young should be given attribution as the author of the parts of the library used.

This can be in the form of a textual message at program startup or in documentation (online or textual) provided with the package.

Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:

1. Redistributions of source code must retain the copyright notice, this list of conditions and the following disclaimer.

2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.

3. All advertising materials mentioning features or use of this software must display the following acknowledgement:

“This product includes cryptographic software written by

Eric Young ([email protected])”

The word ‘cryptographic’ can be left out if the rouines from the library being used are not cryptographic related :-).

4. If you include any Windows specific code (or a derivative thereof) from the apps directory (application code) you must include an acknowledgement:

“This product includes software written by Tim Hudson

([email protected])”

THIS SOFTWARE IS PROVIDED BY ERIC YOUNG “AS IS”

AND ANY EXPRESS OR IMPLIED WARRANTIES,

INCLUDING, BUT NOT LIMITED TO, THE IMPLIED

WARRANTIES OF MERCHANTABILITY AND FITNESS

FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN

NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS

BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,

SPECIAL, EXEMPLARY, OR CONSEQUENTIAL

DAMAGES (INCLUDING, BUT NOT LIMITED TO,

PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;

LOSS OF USE, DATA, OR PROFITS; OR BUSINESS

INTERRUPTION) HOWEVER CAUSED AND ON ANY

THEORY OF LIABILITY, WHETHER IN CONTRACT,

STRICT LIABILITY, OR TORT (INCLUDING

NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY

OUT OF THE USE OF THIS SOFTWARE, EVEN IF

ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

The licence and distribution terms for any publically available version or derivative of this code cannot be changed. i.e. this code cannot simply be copied and put under another distribution licence [including the GNU Public Licence.]

FreeType

The FreeType Project is copyright (C) 1996-2000 by David

Turner, Robert Wilhelm, and Werner Lemberg. All rights reserved except as specified below.

THE FREETYPE PROJECT IS PROVIDED ‘AS IS’

WITHOUT WARRANTY OF ANY KIND, EITHER

EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED

TO, WARRANTIES OF MERCHANTABILITY AND

FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT

WILL ANY OF THE AUTHORS OR COPYRIGHT

HOLDERS BE LIABLE FOR ANY DAMAGES CAUSED BY

THE USE OR THE INABILITY TO USE, OF THE

FREETYPE PROJECT.

Notice about NetBSD Software

BSD License

Copyright (c) 1994-2004 The NetBSD Foundation, Inc. All rights reserved.

Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:

1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.

2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.

3. All advertising materials mentioning features or use of this software must display the following acknowledgement:

This product includes software developed by the NetBSD

Foundation, Inc. and its contributors.

4. Neither the name of The NetBSD Foundation nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission.

THIS SOFTWARE IS PROVIDED BY THE REGENTS AND

CONTRIBUTORS “AS IS” AND ANY EXPRESS OR

IMPLIED WARRANTIES, INCLUDING, BUT NOT

LIMITED TO, THE IMPLIED WARRANTIES OF

MERCHANTABILITY AND FITNESS FOR A

PARTICULAR PURPOSE ARE DISCLAIMED. IN NO

EVENT SHALL THE REGENTS OR CONTRIBUTORS BE

LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,

SPECIAL, EXEMPLARY, OR CONSEQUENTIAL

DAMAGES (INCLUDING, BUT NOT LIMITED TO,

PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;

LOSS OF USE, DATA, OR PROFITS; OR BUSINESS

INTERRUPTION)

HOWEVER CAUSED AND ON ANY THEORY OF

LIABILITY, WHETHER IN CONTRACT, STRICT

LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR

OTHERWISE) ARISING IN ANY WAY OUT OF THE USE

OF THIS SOFTWARE, EVEN IF ADVISED OF THE

POSSIBILITY OF SUCH DAMAGE.

The following notices are required to satisfy the license terms of the software that we have mentioned in this document:

This product includes software developed by Adam Glass.

This product includes software developed by Bill Paul.

This product includes software developed by Charles M.

Hannum.

This product includes software developed by Christian E.

Hopps.

This product includes software developed by Christopher G.

Demetriou.

This product includes software developed by Christopher G.

Demetriou for the NetBSD Project.

This product includes software developed by Christos Zoulas.

This product includes software developed by Gardner

Buchanan.

This product includes software developed by Gordon W. Ross

,continued

75

76

This product includes software developed by Jonathan Stone for the NetBSD Project.

This product includes software developed by Manuel Bouyer.

This product includes software developed by Rolf Grossmann.

This product includes software developed by TooLs GmbH.

This product includes software developed by the NetBSD

Foundation, Inc. and its contributors.

This product includes software developed by the University of

California, Berkeley and its contributors.

This product includes software developed by the University of

California, Lawrence Berkeley Laboratory and its contributors.

This product includes software developed by the University of

California, Lawrence Berkeley Laboratory.

This product includes software developed for the NetBSD

Project by Wasabi Systems, Inc.

This product includes software developed for the NetBSD

Project by Matthias Drochner..

Notice about JPEG

Parts of this product utilize the research results of the

Independent JPEG Group.

Package name sony-target-grel-libjpeg-6b-020201.src.rpm.

In plain English:

1. We don’t promise that this software works. (But if you find any bugs, please let us know!)

2. You can use this software for whatever you want. You don’t have to pay us.

3. You may not pretend that you wrote this software. If you use it in a program, you must acknowledge somewhere in your documentation that you've used the IJG code.

In legalese:

The authors make NO WARRANTY or representation, either express or implied, with respect to this software, its quality, accuracy, merchantability, or fitness for a particular purpose.

This software is provided “AS IS”, and you, its user assume the entire risk as to its quality and accuracy.

This software is copyright (c) 1991-1998, Thomas G. Lane.

All Rights Reserved except as specified below.

Permission is hereby granted to use, copy, modify, and distribute this software (or portions thereof) for any purpose, without fee, subject to these conditions:

(1) If any part of the source code for this software is distributed, then this README file must be included, with this copyright and no-warranty notice unaltered; and any additions, deletions, or changes to the original files must be clearly indicated in accompanying documentation.

(2) If only executable code is distributed, then the accompanying documentation must state that “this software is based in part on the work of the Independent JPEG Group”.

(3) Permission for use of this software is granted only if the user accepts full responsibility for any undesirable consequences; the authors accept NO LIABILITY for damages of any kind.

These conditions apply to any software derived from or based on the IJG code, not just to the unmodified library. If you use our work, you ought to acknowledge us.

Permission is NOT granted for the use of any IJG author’s name or company name in advertising or publicity relating to this software or products derived from it. This software may be referred to only as “the Independent JPEG Group’s software”.

We specifically permit and encourage the use of this software as the basis of commercial products, provided that all warranty or liability claims are assumed by the product vendor.

Notice about PuTTY Software

This product contains some code of the application PuTTY.

Source package: putty-0.58.tar.gz

License text: http://www.chiark.greenend.org.uk/~sgtatham/ putty/licence.html

PuTTY is copyright 1997-2006 Simon Tatham.

Portions copyright Robert de Bath, Joris van Rantwijk, Delian

Delchev, Andreas Schultz, Jeroen Massar, Wez Furlong,

Nicolas Barry, Justin Bradford, Ben Harris, Malcolm Smith,

Ahmad Khalifa, Markus Kuhn, and CORE SDI S.A.

Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated documentation files (the “Software”), to deal in the Software without restriction, including without limitation the rights to use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of the

Software, and to permit persons to whom the Software is furnished to do so, subject to the following conditions:

The above copyright notice and this permission notice shall be included in all copies or substantial portions of the Software.

THE SOFTWARE IS PROVIDED “AS IS”, WITHOUT

WARRANTY OF ANY KIND, EXPRESS OR IMPLIED,

INCLUDING BUT NOT LIMITED TO THE WARRANTIES

OF MERCHANTABILITY, FITNESS FOR A PARTICULAR

PURPOSE AND NONINFRINGEMENT. IN NO EVENT

SHALL SIMON TATHAM BE LIABLE FOR ANY CLAIM,

DAMAGES OR OTHER LIABILITY, WHETHER IN AN

ACTION OF CONTRACT, TORT OR OTHERWISE,

ARISING FROM, OUT OF OR IN CONNECTION WITH THE

SOFTWARE OR THE USE OR OTHER DEALINGS IN THE

SOFTWARE.

Notice about fdlibm Software

@(#)fdlibm.h 1.5 95/01/18

Copyright (C) 1993 by Sun Microsystems, Inc. All rights reserved.

Developed at SunSoft, a Sun Microsystems, Inc. business.

Permission to use, copy, modify, and distribute this software is freely granted,provided that this notice is preserved.

Notice about Root Certificates

In addition, the Runtimes and Runtime Components may contain one or more root certificates (herein referred to as “Root

Certificates”). You may not modify the Root Certificates.

Notice about Nano-XML

Copyright (C) 2000-2002 Marc De Scheemaecker, All Rights

Reserved.

This software is provided ‘as-is’, without any express or implied warranty. In no event will the authors be held liable for any damages arising from the use of this software.

Permission is granted to anyone to use this software for any purpose, including commercial applications, and to alter it and redistribute it freely, subject to the following restrictions:

1. The origin of this software must not be misrepresented; you must not claim that you wrote the original software. If you use this software in a product, an acknowledgment in the product documentation would be appreciated but is not required.

2. Altered source versions must be plainly marked as such, and must not be misrepresented as being the original software.

3. This notice may not be removed or altered from any source distribution.

Glossary

AACS

“Advanced Access Content System” is a specification for managing digital entertainment contents stored on the next generation of prerecorded and recorded optical media. The specification enables consumers to enjoy digital entertainment content, including high-definition content.

AVCHD (page 61)

The AVCHD format is a high definition digital video camera format used to record

SD (standard definition) or HD (high definition) signals of either the 1080i specification

*1

or the 720p specification

*2

on

DVDs, using efficient data compression coding technology. The MPEG-4 AVC/

H.264 format is adopted to compress video data, and the Dolby Digital or Linear PCM is used to compress audio data. The MPEG-4

AVC/H.264 format is capable of compressing images at higher efficiency than that of the conventional image compression format. The MPEG-4 AVC/H.264 format enables a high definition (HD) video signal shot on a digital video camera recorder to be recorded on DVDs in the same way as for a standard definition (SD) television signal.

*1

A high definition specification that utilizes 1080 effective scanning lines and the interlace format.

*2

A high definition specification that utilizes 720 effective scanning lines and the progressive format.

BD-J application

The BD-ROM format supports Java for interactive functions.

“BD-J” offers content providers almost unlimited functionality when creating interactive BD-ROM titles.

BD-R (page 59)

BD-R (Blu-ray Disc Recordable) is a recordable, write-once Blu-ray Disc, available in the same capacities as the BD below. Since contents can be recorded and cannot be overwritten, a BD-R can be used to archive valuable data or storing and distributing video material.

BD-RE (page 59)

BD-RE (Blu-ray Disc Rewritable) is a recordable and rewritable Blu-ray Disc, available in the same capacities as the BD below. The re-recordable feature makes extensive editing and time-shifting applications possible.

BD-ROM (page 59)

BD-ROMs (Blu-ray Disc Read-Only

Memory) are commercially produced discs and are available in the same capacities as the

BD below. Other than conventional movie and video contents, these discs have enhanced features such as interactive content, menu operations using pop-up menus, selection of subtitle display, and slideshow.

Although a BD-ROM may contain any form of data, most BD-ROM discs will contain movies in High Definition format, for playback on Blu-ray Disc/DVD players.

Blu-ray Disc (BD) (page 59)

A disc format developed for recording/ playing high-definition (HD) video (for

HDTV, etc.), and for storing large amounts of data. A single layer Blu-ray Disc holds up to

25 GB, and a dual-layer Blu-ray Disc holds up to 50 GB of data.

Dolby Digital Plus (page 63)

Developed as an extension to Dolby Digital, the audio coding technology supports 7.1 multi-channel surround sound.

Dolby TrueHD (page 63)

Dolby TrueHD is a lossless coding technology that supports up to 8 channels of multi-channel surround sound for the next generation optical discs. The reproduced sound is true to the original source bit-for-bit.

DTS-HD High Resolution Audio (page 63)

Developed as an extension to DTS Digital

Surround format. It supports a maximum sampling frequency of 96 kHz, and 7.1 multichannel surround.

DTS-HD High Resolution Audio has a maximum transmission rate of 6 Mbps, with lossy compression (Lossy).

,continued

77

78

DTS-HD Master Audio (page 63)

DTS-HD Master Audio has a maximum transmission rate of 24.5 Mbps, and uses lossless compression (Lossless), and DTS-

HD Master Audio corresponds to a maximum sampling frequency of 192 kHz, and maximum of 7.1ch.

HDMI (High-Definition Multimedia

Interface) (page 15)

HDMI is an interface that supports both video and audio on a single digital connection. The

HDMI connection carries standard- to highdefinition video signals and multi-channel audio signals to AV components such as

HDMI equipped TVs, in digital form without degradation.

The HDMI specification supports HDCP

(High-bandwidth Digital Contents

Protection), a copy protection technology for digital entertainment contents for HDMI.

LTH (Low to High) (page 60)

LTH is a recording system that supports organic pigment type BD-R.

PhotoTV HD (page 39)

“PhotoTV HD” allows for a highly-detailed pictures, and photo-like expression of subtle textures and colors. By connecting Sony

“PhotoTV HD” compatible devices using an

HDMI cable, whole new world of photos can be enjoyed in breathtaking Full HD quality.

For instance, the delicate texture of the human skin, flowers, sand and waves can now be displayed on a large screen in beautiful photo-like quality.

Pop-up menu (page 33)

An enhanced menu operation available on

BD-ROMs. The pop-up menu appears when

POP UP/MENU is pressed during playback, and can be operated while playback is in progress.

x.v.Color (page 45)

x.v.Color is a familiar term for the xvYCC standard proposed by Sony.

xvYCC is an international standard for Color space in video.

This standard can express a wider color range than the currently used broadcast standard.

24p True Cinema (page 44)

Movies shot with a film camera consist of 24 frames per second.

Since conventional televisions (both CRT and flat panels) display frames either at 1/60 or 1/50 second intervals, the 24 frames do not appear at an even pace.

When connected to a TV with 24p capabilities, the player displays each frame at

1/24 second intervals — the same interval originally shot with the film camera, thus faithfully reproducing the original cinema image.

Index

Words in quotations appear in the on-screen displays.

Numerics

24p True Cinema

78

A

“A/V Settings”

35

AACS

77

ANGLE

8

AUDIO

8

“Audio Output Priority”

45

Audio output signals

63

“Audio Settings”

36

,

45

AVCHD

61

,

77

B

Batteries

26

“BD Data”

34

,

56

“BD/DVD Viewing

Settings”

47

BD-R

59

,

77

BD-RE

59

,

77

Bitstream

63

Blu-ray Disc

59

,

77

BonusView

23

,

33

BRAVIA Sync

16

,

56

C

CD

59

Chapter

34

Child Lock

10

,

57

Color buttons

9

Connecting

AV amplifier

(receiver)

19

TV

14

“Control for HDMI”

16

,

32

,

50

,

56

D

“Dimmer”

50

Disc information

35

Disc Lock

32

DISPLAY

8

Dolby Digital

21

,

46

Dolby Digital Plus

63

,

77

Dolby TrueHD

63

,

77

DTS

21

,

46

DTS-HD

63

,

77

DVD

59

E

Easy Setup

28

,

53

Enter characters

52

External memory

23

,

33

,

56

F

Front panel display

11

H

HDMI

15

,

20

,

28

,

43

,

45

,

56

,

78

HOME

9

Home menu

37

,

38

,

40

L

Language Follow

16

Local storage

23

,

33

,

56

LTH

78

M

“Music”

37

N

“Network Diagnostic”

51

“Network Settings”

51

“Network Update”

24

,

41

O

One-Touch Play

16

,

32

OPTIONS

9

,

33

,

37

,

38

“OSD”

50

P

Parental Control

32

,

47

“Photo”

38

“Photo Settings”

49

PhotoTV HD

39

,

78

Playable discs

59

POP UP/MENU

9

,

33

Q

“Quick Start”

50

R

Region code

60

Remote

8

,

26

,

27

“Resetting”

53

Resetting the player

53

Resume

9

,

32

,

37

S

SCENE SEARCH

9

Searching

34

Self-diagnosis function

58

“Setup”

40

Slideshow

38

Software update

24

,

41

,

50

“Standby Mode”

50

SUBTITLE

8

System Power-Off

16

“System Settings”

50

T

THEATER

8

,

16

Title

34

TOP MENU

9

Troubleshooting

54

“TV Type”

42

U

Update

24

,

41

V

“Video”

31

Video output resolution

62

“Video Settings”

35

,

42

X

x.v.Color

45

,

78

79

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement

Table of contents