TOSHIBA e-STUDIO 165/205 Multifunctional Digital System Quick Start Guide
Below you will find brief information for Multifunctional Digital System e-STUDIO 165/205. These devices can be connected to a computer using a USB cable or to a network via TCP/IP or IPX/SPX. They support a variety of features, including printing, scanning, and sending faxes. They are compatible with Windows, Macintosh, and Unix operating systems.
Advertisement
Advertisement
MULTIFUNCTIONAL DIGITAL SYSTEMS
Quick Start Guide for
Printing Functions
DISCLAIMER NOTICE
The following notice sets out the exclusions and limitations of liability of TOSHIBA TEC CORPORATION
(including its employees, agents and sub-contractors) to any purchaser or user (‘User’) of the e-
STUDIO520/600/720/850, including its accessories, options and bundled software (‘Product’).
1. The exclusion and limitations of liability referred to in this notice shall be effective to the fullest extent permissible at law. For the avoidance of doubt, nothing in this notice shall be taken to exclude or limit
TOSHIBA TEC CORPORATION’s liability for death or personal injury caused by TOSHIBA TEC COR-
PORATION’s negligence or TOSHIBA TEC CORPORATION’s fraudulent misrepresentation.
2. All warranties, conditions and other terms implied by law are, to the fullest extent permitted by law, excluded and no such implied warranties are given or apply in relation to the Products.
3. TOSHIBA TEC CORPORATION shall not be liable for any loss, cost, expense, claim or damage whatsoever caused by any of the following:
- use or handling of the Product otherwise than in accordance with the manuals, including but not limited to Operator’s Manual, User’s Guide, and/or incorrect or careless handling or use of the Product;
- any cause which prevents the Product from operating or functioning correctly which arises from or is attributable to either acts, omissions, events or accidents beyond the reasonable control of
TOSHIBA TEC CORPORATION including without limitation acts of God, war, riot, civil commotion, malicious or deliberate damage, fire, flood, or storm, natural calamity, earthquakes, abnormal voltage or other disasters;
- additions, modifications, disassembly, transportation, or repairs by any person other than service technicians authorized by TOSHIBA TEC CORPORATION; or
- use of paper, supplies or parts other than those recommended by TOSHIBA TEC CORPORATION.
4. Subject to paragraph 1, TOSHIBA TEC CORPORATION shall not be liable to Customer for:
- loss of profits; loss of sales or turnover; loss of or damage to reputation; loss of production; loss of anticipated savings; loss of goodwill or business opportunities; loss of customers; loss of, or loss of use of, any software or data; loss under or in relation to any contract; or
- any special, incidental, consequential or indirect loss or damage, costs, expenses, financial loss or claims for consequential compensation; whatsoever and howsoever caused which arise out of or in connection with the Product or the use or handling of the Product even if TOSHIBA TEC CORPORATION is advised of the possibility of such damages.
TOSHIBA TEC CORPORATION shall not be liable for any loss, cost, expense, claim or damage caused by any inability to use (including, but not limited to failure, malfunction, hang-up, virus infection or other problems) which arises from use of the Product with hardware, goods or software which TOSHIBA TEC
CORPORATION has not directly or indirectly supplied
2 DISCLAIMER NOTICE
SOFTWARE LICENSE AGREEMENT
INSTALLING OR OTHERWISE USING THIS SOFTWARE PRODUCT CONSTITUTES YOUR ACCEP-
TANCE OF THE FOLLOWING TERMS AND CONDITIONS (UNLESS A SEPARATE LICENSE IS PRO-
VIDED BY THE SUPPLIER OF APPLICABLE SOFTWARE IN WHICH CASE SUCH SEPARATE LICENSE
SHALL APPLY). IF YOU DO NOT ACCEPT THESE TERMS, YOU MAY NOT INSTALL OR USE THIS
SOFTWARE, AND YOU MUST PROMPTLY RETURN THE SOFTWARE TO THE LOCATION WHERE
YOU OBTAINED IT.
THE SOFTWARE INSTALLED ON THIS PRODUCT INCLUDES NUMEROUS INDIVIDUAL SOFTWARE
COMPONENTS, EACH HAVING ITS OWN APPLICABLE END USER LICENSE AGREEMENT (“EULA”).
INFORMATION RELATING TO THE EULAS MAY BE FOUND IN AN ELECTRONIC FILE INCLUDED ON
THE USER DOCUMENTATION CD-ROM INCLUDED HEREWITH; HOWEVER, ALL SOFTWARE AND
DOCUMENTATION DEVELOPED OR CREATED BY OR FOR TOSHIBA TEC CORPORATION (“TTEC”)
ARE PROPRIETARY PRODUCTS OF TTEC AND ARE PROTECTED BY COPYRIGHT LAWS, INTERNA-
TIONAL TREATY PROVISIONS, AND OTHER APPLICABLE LAWS.
Grant of License
This is a legal agreement between you, the end-user (“You”), and TTEC and its suppliers. This software, fonts (including their typefaces) and related documentation (“Software”) is licensed for use with the system
CPU on which it was installed (“System”) in accordance with the terms contained in this Agreement. This
Software is proprietary to TTEC and/or its suppliers.
TTEC and its suppliers disclaim responsibility for the installation and/or use of this Software, and for the results obtained by using this Software. You may use one copy of the Software as installed on a single System, and may not copy the Software for any reason except as necessary to use the Software on a single
System. Any copies of the Software shall be subject to the conditions of this Agreement.
You may not, nor cause or permit any third party to, modify, adapt, merge, translate, reverse compile, reverse assemble, or reverse engineer the Software. You may not use the Software, except in accordance with this license. No title to the intellectual property in the Software is transferred to you and full ownership is retained by TTEC or its suppliers. Source code of the Software is not licensed to you. You will be held legally responsible for any copyright infringement, unauthorized transfer, reproduction or use of the Software or its documentation.
Term
This license is effective until terminated by TTEC or upon your failure to comply with any term of this Agreement. Upon termination, you agree to destroy all copies of the Software and its documentation.
You may terminate this license at any time by destroying the Software and its documentation and all copies.
Disclaimer of Warranty
THIS SOFTWARE IS PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR
IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY,
FITNESS FOR A PARTICULAR PURPOSE, TITLE, AND NON-INFRINGEMENT. TTEC AND ITS SUPPLI-
ERS DISCLAIM ANY WARRANTY RELATING TO THE QUALITY AND PERFORMANCE OF THE SOFT-
WARE. IF THE SOFTWARE PROVES DEFECTIVE, YOU (AND NOT TTEC OR ITS SUPPLIERS) SHALL
BE RESPONSIBLE FOR THE ENTIRE COST OF ALL NECESSARY SERVICING, REPAIR OR CORREC-
TION. TTEC AND ITS SUPPLIERS DO NOT WARRANT THAT THE FUNCTIONS CONTAINED IN THE
SOFTWARE WILL MEET YOUR REQUIREMENTS OR THAT THE OPERATION OF THE SOFTWARE
WILL BE UNINTERRUPTED OR ERROR FREE.
ALL INFORMATION CONTAINED HEREIN THAT IS PROVIDED BY TTEC AND ITS AFFILIATES PURSU-
ANT TO A EULA IS PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR
IMPLIED.
SOFTWARE LICENSE AGREEMENT 3
Limitation of Liability
IN NO EVENT WILL TTEC OR ITS SUPPLIERS BE LIABLE TO YOU FOR ANY DAMAGES, WHETHER IN
CONTRACT, TORT, OR OTHERWISE (EXCEPT PERSONAL INJURY OR DEATH RESULTING FROM
NEGLIGENCE ON THE PART OF TTEC OR ITS SUPPLIERS), INCLUDING WITHOUT LIMITATION ANY
LOST PROFITS, LOST DATA, LOST SAVINGS OR OTHER INCIDENTAL, SPECIAL OR CONSEQUEN-
TIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE SOFTWARE, EVEN IF TTEC
OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES, NOR FOR
THIRD PARTY CLAIMS.
U.S. Government Restricted Rights
The Software is provided with RESTRICTED RIGHTS. Use, duplication or disclosure by the U.S. Government is subject to restrictions set forth in subdivision (b) (3) (ii) or (c) (i) (ii) of the Rights in Technical Data and Computer Software Clause set forth in 252.227-7013, or 52.227-19 (c) (2) of the DOD FAR, as appropriate. Contractor/Manufacturer is TOSHIBA TEC Corporation, 6-78, Minami-cho, Mishima-shi, Shizuoka-ken,
411-8520, Japan.
General
You may not sublicense, lease, rent, assign or transfer this license or the Software. Any attempt to sublicense, lease, rent, assign or transfer any of the rights, duties or obligations hereunder is void. You agree that you do not intend to, and will not ship, transmit (directly or indirectly) the Software, including any copies of the Software, or any technical data contained in the Software or its media, or any direct product thereof, to any country or destination prohibited by the United States Government. This license shall be governed by the laws of Japan or, at the election of a Supplier of TTEC concerned with a dispute arising from or relating to this Agreement, the laws of the Country designated from time to time by the relevant Supplier of TTEC. If any provision or portion of this Agreement shall be found to be illegal, invalid or unenforceable, the remaining provisions or portions shall remain in full force and effect.
YOU ACKNOWLEDGE THAT YOU HAVE READ THIS LICENSE AGREEMENT AND THAT YOU UNDER-
STAND ITS PROVISIONS. YOU AGREE TO BE BOUND BY ITS TERMS AND CONDITIONS. YOU FUR-
THER AGREE THAT THIS LICENSE AGREEMENT CONTAINS THE COMPLETE AND EXCLUSIVE
AGREEMENT BETWEEN YOU AND TTEC AND ITS SUPPLIERS AND SUPERSEDES ANY PROPOSAL
OR PRIOR AGREEMENT, ORAL OR WRITTEN, OR ANY OTHER COMMUNICATION RELATING TO THE
SUBJECT MATTER OF THIS LICENSE AGREEMENT.
TOSHIBA TEC Corporation, 6-78, Minami-cho, Mishima-shi, Shizuoka-ken, 411-8520, Japan.
4 SOFTWARE LICENSE AGREEMENT
Preface
Thank you for purchasing the Toshiba multifunctional digital system e-STUDIO165/205.
This Quick Start Guide for Printing Functions is a manual for the e-STUDIO165/205 when the following option is installed:
Network Printer Kit
This Quick Start Guide for Printing Functions explains about the accessories, conditions required for network systems, connecting procedures of a network, general description of network settings, default setting lists and troubleshooting.
Be sure to read this manual before using the e-STUDIO165/205 with the options shown above.
Keep this manual handy and retain it for future reference.
Preface 5
Lineup of Our Manuals
These manuals are provided for the operation of the e-STUDIO165/205. Select and read the manual best suited to your needs.
MULTIFUNCTIONAL DIGITAL SYSTEMS
Operator's Manual for Copying Functions
Operator’s Manual for Copying Functions
This manual describes the basic operations, mainly copying functions, of this equipment. Be sure to read this before you use this equipment.
MULTIFUNCTIONAL DIGITAL SYSTEMS
Quick Start Guide for
Printing Functions
Quick Start Guide for Printing Functions (This manual)
This manual describes the operation of the equipment when the Network Printer Kit (optional) is installed on it. This also explains about the accessories, conditions required for network systems, connecting method of the network, general description of network settings and troubleshooting.
Network Administration
Guide for Printing
Functions
Network Administration Guide for Printing Functions (PDF)
This manual is only for the equipment on which the Network Printer Kit
(optional) is installed. This provides you with setup procedures by the type of platforms or networks you are utilizing, and also setup procedures for network servers to enable various network services.
MULTIFUNCTIONAL DIGITAL SYSTEMS
Setup Guide for
Printing Functions
MULTIFUNCTIONAL DIGITAL SYSTEMS
Printing Guide
Setup Guide for Printing Functions (PDF)
This manual is only for the equipment on which the Network Printer Kit
(optional) is installed. The manual consists of the following 2 parts:
Settings Using Control Panel:
This part describes the printer-related settings using the [PRINTER] and [USER FUNCTIONS] buttons on the control panel of this equipment.
Settings Using TopAccess:
This manual describes how to set up this equipment from your computer through a network using a web-based utility TopAccess. This also explains about functions to check the current status of this equipment.
Printing Guide (PDF)
This manual is only for the equipment on which the Network Printer Kit
(optional) is installed. This describes how to install client software for printing data to your computer. This also describes how to print data sent from your computer to this equipment.
6 Lineup of Our Manuals
MULTIFUNCTIONAL DIGITAL SYSTEMS
Network Fax Guide
Network Fax Guide (PDF)
This manual is only for the equipment on which the Fax Kit (optional) and the Network Printer Kit (optional) are installed. This explains about the network Fax functions, which enable Fax transmissions from a client computer through a network.
To read manuals of PDF (Portable Document Format) files
Viewing and printing this operator‘s manual of PDF files require that you install Abobe Reader or
Adobe Acrobat Reader on your PC. If Adobe Reader or Adobe Acrobat Reader is not installed on your PC, download and install it from the website of Adobe Systems Incorporated.
Lineup of Our Manuals 7
Before Reading This Manual
Signage in this manual
In this manual, some important items are descried with the signage shown below. Be sure to read these items before using this equipment.
Indicates a procedure you should follow to ensure the optimal performance of the equipment and problem-free printing.
Describes handy information that is useful to know when operating the equipment.
Pages describing items related to what you are currently doing. See these pages as required.
Trademarks
The official name of Windows 98 is Microsoft Windows 98 Operating System.
The official name of Windows Me is Microsoft Windows Me Operating System.
The official name of Windows 2000 is Microsoft Windows 2000 Operating System.
The official name of Windows XP is Microsoft Windows XP Operating System.
The official name of Windows Server 2003 is Microsoft Windows Server 2003 Operating
System.
Microsoft, Windows, Windows NT, and the brand names and product names of other
Microsoft products are trademarks of Microsoft Corporation in the US and other countries.
Apple, AppleTalk, Macintosh, Mac, TrueType, and LaserWriter are trademarks of Apple
Computer Inc. in the US and other countries.
Postscript is a trademark of Adobe Systems Incorporated.
Netscape is a trademark of Netscape Communications Corporation.
IBM, AT and AIX are trademarks of International Business Machines Corporation.
NOVELL, NetWare, and NDS are trademarks of Novell, Inc.
Other company names and product names in this manual are the trademarks of their respective companies.
©2006 TOSHIBA TEC CORPORATION All rights reserved
This manual is protected by copyright laws. No part of this manual shall be duplicated or reproduced without the permission of TOSHIBA TEC CORPORATION. TOSHIBA TEC CORPORA-
TION shall not be liable in terms of granting patents for any use of information contained in this manual by third parties.
8 Before Reading This Manual
CONTENTS
SOFTWARE LICENSE AGREEMENT ..........................................................3
Before Reading This Manual .......................................................................8
Chapter 1 INTRODUCTION
Function Enhancement by Option Configurations .................................12
Items Included in Optional Kits.................................................................14
Network Printer Kit (optional) ..................................................................14
CD-ROMs of the Network Printer Kit .......................................................15
Client Utilities CD-ROM of the Network Printer Kit .................................16
Chapter 2 SYSTEM REQUIREMENTS
General requirements..............................................................................20
When only the Network Printer Kit is installed.........................................20
When the Network Printer Kit and the Fax Kit are installed.....................21
Chapter 3 CONNECTING TO A COMPUTER
Connecting to the USB Port ......................................................................24
Connecting to the Network........................................................................25
Chapter 4 SETUP FLOW
Overview of Connecting Configurations..................................................28
Connecting the e-STUDIO165/205..........................................................28
Available functions under each connection .............................................29
Setup the network document processing system ....................................31
Setup Flow for USB Printing .....................................................................33
Setup Flow for TopAccess ........................................................................34
CONTENTS 9
Chapter 5 APPENDIX
Default settings for network setting .........................................................36
Default settings for print service ..............................................................38
Troubleshooting at Network Printing Setups ..........................................39
Network setting checklists .......................................................................39
Equipment detection and printing check..................................................43
Printer driver installation error messages ................................................49
When printing cannot be performed ........................................................55
Printer driver general errors.....................................................................55
TopAccess error messages.....................................................................57
10 CONTENTS
1.
INTRODUCTION
This chapter describes the details of option configurations.
Function Enhancement by Option Configurations..............................................12
1 INTRODUCTION
Function Enhancement by Option Configurations
This section provides you with the general descriptions of functions enabled with each option
(the Network Printer Kit and Fax Kit).
For details of the function of the Fax Kit (optional), see the Operator’s Manual for Facsimile Functions.
When the Network Printer Kit (optional) is installed, the USB terminal originally installed on this equipment will be disabled, and therefore, some functions such as GDI printing from a computer using the TOSHIBA Viewer will be disabled too.
The general descriptions of the functions and the option configurations are shown below.
When no options above are installed
Some functions such as a GDI printing using the TOSHIBA Viewer are enabled with a USB connector.
USB
To a computer
(GDI printing with TOSHIBA Viewer)
Equipment
(Copying functions)
When the Network Printer Kit is installed
Network printing is enabled when the Network Printer Kit is installed. (USB printing is also enabled with the USB connector of this kit.)
TopAccess, a web-based utility, is enabled when the Network Printer Kit is installed. You can manage or set up this equipment through TopAccess installed on a client computer.
Equipment
(Copying functions)
Network Printer Kit
(Network printing /
TopAccess)
USB
LAN
To a computer
(USB printing)
To a network
(network printing)
12 Function Enhancement by Option Configurations
When the Network Printer Kit and the Fax Kit are installed
Network printing is enabled when the Network Printer Kit is installed. (USB printing is also enabled with the USB connector of this kit.)
TopAccess, a web-based utility, is enabled when the Network Printer Kit is installed. You can manage or set up this equipment through TopAccess installed on a client computer.
Network Fax transmission (data transmission from a client computer) is enabled when the
Network Printer Kit and the Fax Kit are installed.
Transmission and reception of Fax data through public switched telephone networks are enabled when the Fax Kit is installed.
* The External Keyboard (optional) is used for entering and registering the destinations of the Fax (This is not used in network Fax functions.)
External Keyboard
Equipment
(Copying functions)
Fax Kit
Network Printer Kit
(Network printing /
TopAccess)
TEL
To a Fax machine
(Fax transmission/reception)
USB
LAN
To a computer
(USB printing)
To a network
(Network printing)
Function Enhancement by Option Configurations 13
1 INTRODUCTION
Items Included in Optional Kits
This section explains about the accessories of the options. Be sure that all the accessories described in this section are attached.
In case any of them is lacking or damaged, contact your service representative.
Network Printer Kit (optional)
The Network Printer Kit includes the following accessories:
See the following page for the content of each CD-ROM:
Quick Start Guide for Printing Functions
Font CD-ROM Client Utilities CD-ROM User Documentation CD-ROM
14 Items Included in Optional Kits
About the CD-ROM
This section explains about the CD-ROMs attached to each optional kit and the contents of each
CD-ROM.
CD-ROMs of the Network Printer Kit
User Documentation CD-ROM
The User Documentation CD-ROM includes manuals in PDF files.
See the following page for the description of each manual in this CD-ROM: (The manuals denoted with “(PDF)” are included in this CD-ROM.)
Client Utilities CD-ROM
The Client Utilities CD-ROM includes the following client software:
For Windows
PCL6 Printer Driver
PS3 Printer Driver
Network Fax Driver
Address Book Viewer
Agfa TrueType Fonts
For Macintosh
PPD file for Mac OS 8.6, 9.x, and OS X 10.1/10.2 (Classic)
PPD file for Mac OS X 10.2.4 to Mac OS X 10.4.x
For Admin’s client
MIB
CUPS (For Unix)
Others
TopAccess
For more details about the client software in the CD-ROM, see the following section:
P.16 “About the Client Software”
About the CD-ROM 15
1 INTRODUCTION
About the Client Software
This section explains about the details of the client software included in the Client Utilities CD-
ROM.
Client Utilities CD-ROM of the Network Printer Kit
Client software for printing functions
Network printing is enabled using the client software shown below. In this printing, this equipment operates as a network printer.
PCL6 printer driver
This printer driver is used for printing black and white documents that use TrueType fonts, such as a Microsoft Word, from the Windows computers.
PS3 printer driver
This printer driver is used for printing high-graphical-content documents that use PostScript fonts and graphics, such as Adobe PageMaker, from the Windows computers.
Font Manager
Font Manager allows users to manage the TrueType fonts on the Windows computers.
Macintosh PPD files
There are two PPD files provided in the Client Utilities CD-ROM: one is for Mac OS 8.6/9.x and OS X 10.1/10.2 (Classic), and the other one is for Mac OS X 10.2.4 to Mac OS X 10.4.x.
These PPD files allow users to print from the Macintosh computers over the TCP/IP or
AppleTalk network.
CUPS (For Unix)
The Client Utilities CD-ROM includes the CUPS files that enable the CUPS print system on the UNIX workstation.
Further details about the above client software are given in the Printing Guide.
Client software for network management
TopAccess
TopAccess, a web-based utility, enables you to view the information of this equipment, monitor and manage jobs, and manage the address book, etc. It also provides the administration functions to set up and maintain this equipment.
Further details about the functions of TopAccess are given in the Setup Guide for Printing
Functions.
16 About the Client Software
Client software for network fax functions
Network Fax Driver
The Network Fax Driver enables you to set up the lists for destinations, and send electronic documents as Fax documents from your computer to one or more destinations.
Address Book Viewer
The Address Book Viewer enables you to add or modify the names and numbers of Fax recipients in the address book. This utility allows you to manage the data of the Fax recipients, select and view the recipients – as well as their Fax numbers and other contact information - in the address book.
Further details about the above client software are given in the Network Fax Guide.
About the Client Software 17
1 INTRODUCTION
18 About the Client Software
2.
SYSTEM REQUIREMENTS
This chapter describes system requirements.
2 SYSTEM REQUIREMENTS
System Requirements
This equipment supports various functions under the environments shown below. The functions available for users vary depending on the environment. This section describes the environments required for each function.
The copying functions of this equipment do not require any special environments. You can utilize these functions when you turn the power of this equipment ON.
General requirements
Connector cable
This equipment requires the following cables to connect with your computers:
For USB Connection: USB 2.0 compatible cable
For Ethernet Connection: 10BASE-T/100BASE-TX STP cable with a Category 5
RJ-45 connector
When only the Network Printer Kit is installed
This equipment requires the following environments for printing functions:
TopAccess Web-base management utility
Network protocol: TCP/IP, HTTP
Browser for Windows: Microsoft Internet Explorer 5.5 or later
Netscape Navigator 7.1 or later
Browser for Macintosh:
Browser for UNIX:
Microsoft Internet Explorer 5.5 or later
Netscape Navigator 7.1 or later
Netscape Navigator 7.1 or later
Printing functions
Printing from Windows platform
Display resolution:
Display color:
CPU:
1024 x 768 dots or more
High Color (16bit) or higher is recommended
Pentium 133 MHz minimum
(Pentium 266 MHz or faster recommended)
Memory:
OS:
64MB or more for Windows 98
96MB or more for Windows Me and Windows NT 4.0
128MB or more for Windows 2000/XP/Server 2003
Windows 98 Operating System, English Version
Windows Me Operating System, English Version
Windows NT Workstation Operating System 4.0, English Version
Windows NT Server Network Operating System 4.0, English Version
Windows 2000 Professional Operating System, English Version
Windows 2000 Server Operating System, English Version
Windows XP Home Edition Operating System, English Version
Windows XP Professional Operating System, English Version
Connectability:
Network protocol:
Printing protocol:
Windows Server 2003 Operating System, English Version
USB 2.0, Ethernet
TCP/IP, IPX/SPX
Raw TCP, LPR/LPD, IPP v1.1
NetWare PSERVER with NDS or Bindery
NetWare Print Server (if printing with the NetWare file server)
NetWare 5.1 (NDS or NDPS)
NetWare 6.5 (NDS or NDPS)
20 System Requirements
USB printing is not supported by Windows NT 4.0.
Printing from Macintosh platform
Display resolution:
OS:
1024 x 768 dots or more
Mac OS 8.6, Mac OS 9.x, Mac OS X 10.1/10.2 (Classic)
Connectability:
Network protocol:
Printing protocol:
Printer driver:
Mac OS X 10.2.4 later
Ethernet
TCP/IP, AppleTalk, Bonjour (Mac OS X 10.4.x)
AppleTalk, LPR/LPD, IPP
LaserWriter 8 (Only required for Mac OS 8.6/9.x and Mac OS X
10.1/10.2 Classic)
USB printing is not supported by Macintosh.
Printing from UNIX platform
OS: Operating systems that support CUPS
Connectability:
Network protocol:
Printing protocol:
Ethernet
TCP/IP
IPPv1.1
When the Network Printer Kit and the Fax Kit are installed
The equipment must be under the environments introduced as follows to enable the printing functions and the network fax functions.
Printing function
P.10 "When only the Network Printer Kit is installed"
Network fax function
Connectability: Public Switched Telephone Network (PSTN)
System Requirements 21
2 SYSTEM REQUIREMENTS
22 System Requirements
3.
CONNECTING TO A COMPUTER
This chapter describes how to connect the connector of the optional kit to a computer or a network.
3 CONNECTING TO A COMPUTER
Connecting to the USB Port
This section describes how to connect this equipment to a computer using a USB 2.0 compatible cable.
This USB cable is not included in the accessories. Obtain one compatible with your computer.
When the Network Printer Kit is installed, the USB terminal originally installed on this equipment will be disabled. The USB connector described in this step is the connector of the Network Printer Kit.
1
After the Network Printer Kit has been installed, insert the USB cable into the deep end of the USB interface connector on the rear side of this equipment.
2
Connect the other end of the USB cable to the USB port of your computer.
3
Turn ON the power of this equipment and the power of the computer.
24 Connecting to the USB Port
Connecting to the Network
This section describes how to connect this equipment to a network.
The 10BASE-T cable and the 100BASE-TX cable are not included in the accessories. Obtain the ones compatible with the network you are utilizing.
1
After the Network Printer Kit has been installed, insert the10BASE-T or 100BASE-TX cable into the network interface connector on the rear side of this equipment.
2
Turn ON the power of this equipment.
Connecting to the Network 25
3 CONNECTING TO A COMPUTER
26 Connecting to the Network
4.
SETUP FLOW
This chapter describes how to configure the system when the optional kits are installed.
4 SETUP FLOW
Overview of Connecting Configurations
Connecting the e-STUDIO165/205
This equipment supports the various functions of electric document processing in direct connection with a USB cable, and in a network connection such as printing, scanning, and sending Email or internet fax over the Internet. To enable these functions, an administrator has to configure the proper network configuration with client computers, servers, and this equipment.
USB Connection
* USB printing is not supported by
Macintosh.
TCP/IP or IPX/SPX Local Area Network
Windows Me
Windows 2000
Windows XP
Windows Server 2003
Windows 98
Windows Me
Windows NT 4.0
Windows 2000
Windows XP
Windows Server 2003
Unix workstation
Windows Print Server
NetWare Print Server
AppleTalk or TCP/IP Local Area Network
Windows 98
Windows Me
Windows NT 4.0
Windows 2000
Windows XP
Windows Server 2003
Mac OS 8.6
Mac OS 9.x
Mac OS X
Internet
DNS Server
Email Server
28 Overview of Connecting Configurations
Available functions under each connection
Functions available vary depending on each connecting configuration. This section describes the functions available for each connection.
The configurations shown below can be utilized together. For example, this equipment can be directly connected to your computer with a USB cable, and also connected to a local area network over TCP/IP. In this case, all the functions described for each configuration are available for users.
The printing functions are available only when the Network Printer Kit is installed.
USB connection
The following functions are available when this equipment is directly connected to your computer with a USB cable:
Printing functions (Network Printer Kit required)
USB printing from Windows computers
Network fax functions
USB printing is not supported by Windows NT 4.0.
Local area network connection over TCP/IP
The following functions are available when this equipment is connected to a local area network over TCP/IP with which Windows computers, Macintosh computers or UNIX workstations are connected:
Printing functions (Network Printer Kit required)
Raw TCP or LPR printing from Windows computers
IPP printing from Windows computers
Novell printing from Windows computers through the NetWare 5.1 or 6.5 in NDS or NDPS mode
LPR, IP, IPP, and AppleTalk printing from Macintosh computers
Bonjour printing (for Mac OS X10.4.x) from Macintosh computers
IPP and LPR printing from UNIX workstations
Network management functions (Network Printer Kit required)
Monitoring and managing this equipment by client computers using the TopAccess
Network fax functions (Network Printer Kit and Fax Kit required)
Transmitting Fax data from Windows computers using the network Fax driver
Overview of Connecting Configurations 29
4 SETUP FLOW
Local area network connection over IPX/SPX
The following functions are available when this equipment is connected to a local area network over IPX/SPX with which Windows computers and NetWare file servers are connected:
Printing functions (Network Printer Kit required)
Novell Printing from Windows computers through the NetWare 5.1 or 6.5 in NDPS mode
Novell Printing from Windows computers through the NetWare 5.1 or 6.5 in NDS mode
Internet connection
The following functions are available when this equipment is connected to a network where this equipment can access the Internet:
Printing functions
IPP printing from Windows computers over the Internet (Network Printer Kit required)
30 Overview of Connecting Configurations
About Setups
First of all, you must set up the management and the operation of this equipment as a network printer and a network Fax. Although this equipment can operate successfully in the default settings, the following settings can be changed for better performance:
Default setting check
Before using this equipment through a network, check the default settings of this equipment according to the following reference:
Setup the network document processing system
This equipment is an MFP which enables you to have immediate use with the connection to a network you are utilizing.
Even in suitable conditions, however, you need to check if the functions of this equipment are under an appropriate environment for the operation and if they are set enabled as described below. Some functions may require additional settings depending on your environment.
This equipment can provide you with a more advanced document-processing system by adding a few more settings.
The following table shows the references for easy setup flows to enable these document-processing systems:
Options
Network Printer Kit
Network Printer Kit
Setup contents
USB printing
Network printing
Network Printer Kit,
Fax Kit, and External
Keyboard
Network Fax
Network Printer Kit TopAccess
Descriptions References
Setups for a USB printing
Setups for Windows computers
Setups for Macintosh computers
Setups for Unix workstations
Setups for network Fax transmission
Network Administration Guide for
Printing Functions
Setups for TopAccess
About Setups 31
4 SETUP FLOW
Default Setting Check
This section describes the items to be set before using this equipment through a network. Check if the following setups have been done:
Item
Setting the department code
Setting the paper size for each drawer
Setting the device settings
Setting the terminal ID
Description/Reference
The department codes must be set to enable a network printing on a department basis.
Reference: Operator’s Manual for Copying Functions
Chapter 5 “CHANGING EQUIPMENT’S SETTINGS”
“Department Code”
Check if the paper size of each drawer of this equipment is specified prior to network printing.
Reference: Operator’s Manual for Copying Functions
Chapter 5 “CHANGING EQUIPMENT’S SETTINGS”
“Paper Size Setting”
Check if the device settings are made prior to network printing.
Reference: Setup Guide for Printing Functions
Chapter 10 “TopAccess ADMINISTRATION TAB PAGE-
SETUP MENU”
“Setting up Device Settings”
“Setting the device settings”
If the Fax Kit is installed, specify the terminal ID to identify the Fax terminal information.
Reference: Operator’s Manual for Facsimile Functions
Chapter 5 "ENTERING VARIOUS FUNCTIONS"(??)
“Terminal ID Entry”
32 Default Setting Check
Setup Flow for USB Printing
This equipment can be used as a printer using a USB cable. When it is connected using a USB cable, setups at the initial stage are not required. When you have connected this equipment to your computer and installed printer drivers, USB printing functions are enabled.
USB printing is not supported by Windows NT 4.0.
Windows Me
Windows 2000
Windows XP
Windows Server 2003
Connecting using a USB cable
Setup Flow
Connect this equipment
Install the client software
Configuring the printer drivers
Description/Reference
Connect this equipment to your computer using a USB cable.
Reference: Quick Start Guide for Printing Functions (this manual)
• Chapter 3 “CONNECTING TO A COMPUTER”
P.24 “Connecting to the USB Port”
Install the printer driver from the Client Utilities CD-ROM.
Reference: Printing Guide
• Chapter 2 “INSTALLING CLIENT SOFTWARE”
“Installing Client Software for Windows”
“Installing the Client Software for USB Printing”
Configure the options and department codes.
Reference: Printing Guide
• Chapter 3 “PRINTING”
“Printing from Windows”
“Before Using the Printer Driver”
Setup Flow for USB Printing 33
4 SETUP FLOW
Setup Flow for TopAccess
TopAccess, a web-based device management utility, enables a remote management of this equipment for users or administrators from their computers. The following functions are available in TopAccess:
Viewing or setting the information related to this equipment
Managing the address book data
Using TopAccess administrator’s functions, administrators can set up and maintain the equipment remotely.
To enable TopAccess, administrators should set up the network connection between this equipment and your computers over TCP/IP, and should enable the HTTP network services of this equipment.
Setup Flow
Connect this equipment
Set up the TCP/IP
Set up the HTTP network service
Description/Reference
Connect this equipment to your network using a network cable.
Reference: Quick Start Guide for Printing Functions (this manual)
• Chapter 3 “CONNECTING TO A COMPUTER”
P.25 “Connecting to the Network”
Assign the IP address, Subnet mask, and Gateway address.
Reference: Setup Guide for Printing Functions
• Chapter 5 "CONFIGURING NETWORKS (EQUIP-
MENT)"
"TCP/IP Configuration"
Enable the HTTP Network Server.
Reference: Setup Guide for Printing Functions
• Chapter 5 "CONFIGURING NETWORKS (EQUIP-
MENT)"
"HTTP Configuration"
34 Setup Flow for TopAccess
5.
APPENDIX
Troubleshooting at Network Printing Setups.......................................................39
5 APPENDIX
Default Setting List
The printing-related default settings of this equipment are shown below.
The default setting values are the ones set at the factory when this equipment is shipped.
You can see the current setting values by printing the "Configuration Page" from the operation panel of this equipment. See the following page for how to print the "Configuration
Page".
Setup Guide for Printing Functions
Chapter 4 "PRINTING LISTS (EQUIPMENT)"
To Print List
"Configuration page"
Default settings for network setting
General
Link Speed/Duplex Mode ........................................... Auto
TCP/IP
Address Mode............................................................. Dynamic
IP Address .................................................................. Undefined
Subnet Mask ............................................................... Undefined
Default Gateway ......................................................... Undefined
IPX/SPX
Enable IPX/SPX.......................................................... Enable
Frame Type................................................................. Auto Sense
AppleTalk
Enable AppleTalk ........................................................ Enable
Device Name .............................................................. MFP_[NIC Serial Number]
Desired Zone .............................................................. *
DNS session
Enable DNS ................................................................ Enable
Primary DNS Server Address ..................................... 0.0.0.0
Secondary DNS Server Address ................................ 0.0.0.0
DDNS session
Enable DDNS.............................................................. Enable
Host Name .................................................................. MFP-[NIC Serial Number]
Domain Name ............................................................. Undefined
36 Default Setting List
NetWare session
Enable Bindery............................................................ Enable
Enable NDS ................................................................ Enable
Context........................................................................ Undefined
Tree............................................................................. Undefined
Search root ................................................................. Undefined
Bonjour
Enable Bonjour ........................................................... Enable
Link-Local Host Name................................................. MFP_[NIC Serial Number]
Service Name ............................................................. TOSHIBA e-STUDIO520-[serial]
HTTP network service
Enable HTTP Server................................................... Enable
Primary Port Number .................................................. 80
Secondary Port Number ............................................. 8080
SNMP network service
Enable SNMP ............................................................. Enable
Read Community ........................................................ public
Enable Authentication Trap......................................... Enable
Enable Alerts Trap ...................................................... Enable
IP Trap Address1 ........................................................ 0.0.0.0
IP Trap Community ..................................................... public
Default Setting List 37
5 APPENDIX
Default settings for print service
Raw TCP print
Enable Raw TCP ........................................................ Enable
Port Number ............................................................... 9100
LPD print
Enable LPD ................................................................ Enable
Port Number ............................................................... 515
Banners ...................................................................... OFF
IPP print
Enable IPP ................................................................. Enable
Enable Port80 ............................................................. Enable
Port Number ............................................................... 631
URL ............................................................................ http://<IP address>:631/Print
NetWare print
Login Name ................................................................ MFP_[NIC Serial Number]
Password ................................................................... Undefined
Print Queue Scan Rate .............................................. 5 seconds
38 Default Setting List
Troubleshooting at Network Printing Setups
This section describes troubleshooting when you are setting up network printing. Network printing is enabled when the Network Printer Kit is installed.
The items in the table below are described in this section, and are transcribed from other manuals (in PDF files) of this equipment.
Item
Network setting checklists
P.39 “Network setting checklists”
Equipment detection and printing check
P.43 “Equipment detection and printing check”
Printer driver installation error messages
P.49 “Printer driver installation error messages”
Transcribed from
Network Administration Guide for Printing Functions
Network Administration Guide for Printing Functions
Printing Guide
For troubleshooting when the setups have been completed, see the following page:
Network setting checklists
When a computer cannot print data to this equipment through a network, check if the settings are correctly made according to the Network Administration Guide for Printing Functions by referring to the checklists shown below. The checklist covers major printing setting items explained in the Network Administration Guide for Printing Functions.
Raw TCP or LPR printing in a Windows operating system environment:
No Check...
Yes
1 Are the IP Address properties correctly set?
2 Is the Raw TCP Printing correctly set?
Next Step
Next Step
3 Is the LPR/LPD Printing correctly set?
Next Step
4 Were the proper printer drivers installed?
Next Step
5 Is the Raw TCP or LPR port configured with correct IP address?
Next Step
6 Can you print to this equipment?
End
No For Instruction, Go To...
Set up the IP address correctly.
Set up the Raw TCP print service correctly.
Set up the LPD print service correctly.
See the Printing Guide to install proper printer drivers.
See the Printing Guide to configure the proper port.
Refer to the following section to troubleshoot the condition.
P.48 “Cannot print data to this equipment”
Troubleshooting at Network Printing Setups 39
5 APPENDIX
IPP printing in a Windows operating system environment:
No Check...
1 Are the IP Address properties correctly set?
2 Is the HTTP Server on this equipment enabled?
Yes
Next Step
Next Step
3 Is the IPP Printing correctly set?
Next Step
4 Were the proper printer drivers installed?
Next Step
5 Is the IPP port configured with correct URL?
6 Can you print to this equipment?
Next Step
End
No For Instruction, Go To...
Set up the IP address correctly.
Enable the HTTP server in the
HTTP Network Service.
Set up the IPP print service correctly.
See the Printing Guide to install proper printer drivers.
See the Printing Guide to configure proper port.
Refer to the following section to troubleshoot the condition.
P.48 “Cannot print data to this equipment”
Printing via print server in a Windows operating system environment:
No Check...
Yes
1 Are the IP Address properties correctly set?
2 Is the Raw TCP Printing correctly set?
Next Step
Next Step
3 Is the LPR/LPD Printing correctly set?
Next Step
4 Were the proper printer drivers installed?
Next Step
5 Is the Raw TCP or LPR port configured with correct IP address?
Next Step
6 Is the Windows print server correctly set?
7 Can you print to this equipment?
Next Step
End
No For Instruction, Go To...
Set up the IP address correctly.
Set up the Raw TCP print service correctly.
Set up the LPD print service correctly.
See the Printing Guide to install proper printer drivers.
See the Printing Guide to configure the proper port.
Set up the Windows print server correctly.
Refer to the following section to troubleshoot the condition.
P.48 “Cannot print data to this equipment”
40 Troubleshooting at Network Printing Setups
Novell printing in a NetWare environment:
No Check...
1 Are the IPX/SPX protocol enabled? Is the correct frame type selected?
2 If applicable, did you successfully set up queuebased printing?
Yes
Next Step
Next Step
3 Did you configure this equipment for NetWare connection?
Next Step
4 Did you configure this equipment for Novell print service?
Next Step
5 Were the proper printer drivers installed?
Next Step
6 Is the IPP port configured with correct URL?
Next Step
7 Can you see this equipment in Windows Network Neighborhood?
Next Step
8 Can you print to this equipment?
End
No For Instruction, Go To...
Set up the IPX/SPX correctly.
Set up the NetWare server properly.
Set up the NetWare network settings correctly.
Set up the Novell print service correctly.
See the Printing Guide to install proper printer drivers.
See the Printing Guide to configure the proper port.
Check that the SMB protocol is enabled in client computers.
Refer to the following section to troubleshoot the condition.
P.48 “Cannot print data to this equipment”
AppleTalk printing in a Macintosh environment:
No Check...
Yes
1 Is AppleTalk enabled on this equipment?
2 Are the IP Address properties correctly set?
Next Step
Next Step
3 Is this equipment available in the Chooser when you click the LaserWriter 8 printer icon?
Next Step
4 Can you access any other network device from the
Macintosh computer?
5 Can another Macintosh computer on the network print to this equipment? If so, compare the settings to determine which need to be changed to support printing from this machine.
Next Step
End
No For Instruction, Go To...
Enable the AppleTalk.
Set up the IP address correctly.
Make sure the AppleTalk zone is supported by the Macintosh client.
Refer to your Macintosh networking documentation or contact
Macintosh technical support.
Refer to your Macintosh networking documentation or contact
Macintosh technical support.
Troubleshooting at Network Printing Setups 41
5 APPENDIX
LPR printing in a Macintosh environment:
No Check...
Yes
1 Are the IP Address properties correctly set?
2 Is the LPR/LPD Printing correctly set?
Next Step
Next Step
3 Were the proper printer drivers installed?
Next Step
4 Is the LPR port configured with correct IP address?
Next Step
5 Can you print to this equipment?
End
No For Instruction, Go To...
Set up the IP address correctly.
Set up the LPD print service correctly.
See the Printing Guide to install proper printer drivers.
See the Printing Guide to configure the proper port.
Refer to the following section to troubleshoot the condition.
P.48 “Cannot print data to this equipment”
IPP printing in a Unix environment:
No Check...
1 Are the IP Address properties correctly set?
Yes
Next Step
2 Is the HTTP Server on this equipment enabled?
3 Is the IPP Printing correctly set?
Next Step
Next Step
4 Were the proper printer drivers installed?
Next Step
5 Is the IPP port configured with correct URL?
6 Can you print to this equipment?
Next Step
End
No For Instruction, Go To...
Set up the IP address correctly.
Enable the HTTP server in the
HTTP Network Service.
Set up the IPP print service correctly.
See the Printing Guide to install proper printer drivers.
See the Printing Guide to configure proper port.
Refer to the following section to troubleshoot the condition.
P.48 “Cannot print data to this equipment”
42 Troubleshooting at Network Printing Setups
Equipment detection and printing check
When a computer cannot detect this equipment through a network or when network printing is disabled, see the following items to solve the problem:
If the problem persists after you have followed all of the steps, contact TOSHIBA’s authorized dealer for further assistance.
Cannot see this equipment
Problem description
After configuring this equipment, you cannot detect it over the network. This could be the result of configuration conflicts within this equipment, but is more likely to be caused by network configuration errors.
The checklist below helps you identify the cause of the error and search for more information about resolving it.
No For Instruction, Go To...
Set up the proper protocols.
No Check...
Yes
1 Did a startup page print out?
If not, wait until the communication comes online.
Examine the protocol settings that print out on the startup page. Are they correct?
Next Step
2 Print out a configuration page. Make sure there are not any discrepancies or inconsistencies between the current network settings and your network environment. Change the network settings, if necessary. Use the Find Computer utility from your Windows computer to locate this equipment by its device name.
Can you find this equipment?
Next Step
3 Can you locate other computers that are in the same network as this equipment?
Next Step
4 Check link LED activity on the hub and/or NIC of this equipment and the client machine. Do the hardware components appear to be functioning properly?
Next Step
Set up the proper protocol if required.
Once you find this equipment, configure the port that it is mapped correctly to the device.
Check the network settings on the client computer to make sure they are compatible with the network settings on this equipment.
Contact your TOSHIBA service representative.
Troubleshooting at Network Printing Setups 43
5 APPENDIX
No Check...
Yes
5 Make sure that the device name for this equipment is unique and verify that the
WINS and/or DNS server database are not causing potential naming conflicts with the network settings on this equipment. If necessary, change the network settings on this equipment.
After the communication comes back online, can you see this equipment in the network?
Next Step
6 If the network environment is using complex subnet or supernet structures, is the
IP address used by this equipment within the network structures range of valid addresses?
End
No For Instruction, Go To...
Set up the NetBIOS name of the device correctly.
Please contact your local network support specialist for further assistance.
Cannot discover this equipment
Problem description
This equipment is discovered automatically using SNMP.
When Address Book Viewer cannot automatically discover this equipment over the network, the most likely cause is the limitations of the protocols on the supporting computers. In some cases, you need to add or update network components.
The following checklist helps you identify the source of the error ad directs you to where you can find more information about solving it.
No No Check...
Yes
1 Is the SNMP enabled on this equipment?
Is “public” is specify for the
Read Community?
Is “private” is specify for the
Read Write Community?
Next Step
2 Confirm that the protocol suite installed on the client computer has been updated with the latest software for the given operating system.
If your network only supports the IPX/SPX protocol, make sure that the most current version of Novell Client software is installed.
Next Step
For Instruction, Go To...
Enable the SNMP (MIB) and confirm the Read Community and
Read Write Community setting.
See the vendor’s Web site for information about product updates and technical supports.
44 Troubleshooting at Network Printing Setups
No Check...
3 Print a NIC Configuration page from this equipment.
Does this equipment support the same protocol as the network?
4 Change the protocol settings from TopAccess, if necessary, and reboot the equipment for the changes to take effect. Repeat step
2. Was the device discovered?
Yes
Next Step
Next Step
5 Check the NIC Configuration page. Are the IP
Address and subnet mask settings correct?
6 Check the router to make sure it is not filtering out this equipment packets. Is the router processing equipment packets correctly?
Next Step
Next Step
7 Can another computer within the same network segment discover this equipment?
8 Check the NIC Configuration page. Is the Unit Serial
Number part of the device name?
9 Check link activities on the port being used by this equipment and the integrity of the network cable, hub, or switch that connects this equipment to the network.
Replace any network components that you can tell or suspect are faulty.
Next Step
Next Step
End
No For Instruction, Go To...
Configure the proper protocol.
Set up the TCP/IP settings correctly.
Adjust the router settings.
Refer to the following section to troubleshoot the condition.
P.39 “Network setting checklists”
Contact your service representative.
Troubleshooting at Network Printing Setups 45
5 APPENDIX
Cannot ping this equipment
Problem description
You can check if this equipment is correctly connected to a network by executing a ping command from a computer.
If this equipment does not respond when you ping it, there is a problem either with the network configuration or with device operation.
The following checklist helps you identify the source of the error and directs you where you can find more information about solving it.
No No Check...
Yes
1 Confirm that the TCP/IP protocol suite is installed on the client computer.
Next Step
2 Look at the NIC configuration page and confirm the
TCP/IP settings are correct.
Is the IP Address entered and valid? Are the Gateway and Subnet settings correct?
Next Step
3 Reboot this equipment.
Check the NIC Configuration page that prints out. Are the TCP/IP settings correct?
Next Step
4 Try to ping this equipment again. Did this equipment respond to the ping?
Next Step
5 Can you ping this equipment from any other computer within the same network? If not, this equipment might have an IP
Address that is out of range or invalid.
6 Can you ping to another computer within the same network?
Next Step
Next Step
For Instruction, Go To...
The networking section of your operating system documentation.
Enter the correct TCP/IP settings.
The settings are not binding, contact your service representative.
Contact your local network specialist for a valid IP address for this equipment.
Check the computer’s protocol settings to make sure the gateway and subnet settings are correct.
The NIC is faulty or improperly installed. Contact your service representative.
7 If you have customized the device name, you can check if the NIC is functional by restoring the default settings. When this equipment automatically reboots and a NIC Configuration page prints, does the device name include the
NIC’s Unit Serial Number?
Next Step
46 Troubleshooting at Network Printing Setups
No Check...
8 Check link activities on the port being used by the equipment and also the integrity of the network cable, Hub, or Switch that is connecting the equipment to the network. Replace any network components that you suspect are faulty. Can you ping this equipment now?
Yes
End
No For Instruction, Go To...
Contact your service representative.
Cannot print from client computer
Problem description
After following the instructions in this guide to install and configure your hardware, network, and client software, you are still unable to print from a client computer to this equipment. This problem can arise as the result of a hardware malfunction, a network communication or configuration problem, or incorrect client setup or driver properties.
The following checklist will help you identify the source of the errors and direct you to information solving the issue.
No Check...
Yes
1 Is the copier functioning normally? Do copy jobs output properly?
Next Step
No For Instruction, Go To...
Check the device status displayed in the Device tab page of
TopAccess.
2 Check the Device page of
TopAccess. Are the options specified for the job supported by the hardware configuration? If not, delete the job, install the required components, and try again.
Next Step
3 Can you print jobs from other client computers?
Next Step
Contact your service representative.
Refer to the following section to troubleshoot the condition.
P.48 “Cannot print data to this equipment”
4 At this point, the problem you have identified is most likely related to a client-side error.
Refer to the Printing Guide to troubleshoot the error condition.
Troubleshooting at Network Printing Setups 47
5 APPENDIX
Cannot print data to this equipment
Problem description
When you are unable to print to this equipment, network printing services have not been set up correctly, or this equipment has not been properly configured to operate in your network environment. The following checklist will help you identify the source of the error and direct you to information solving the issue.
No For Instruction, Go To...
Set up the proper protocol.
No Check...
Yes
1 Have you set the protocol settings so they are compatible with your network and client protocol settings?
If data sent from a specific computer through a network to this equipment are successfully printed, this could be a network configuration error, not a hardware malfunction or the incorrect connection of this equipment.
Next Step
2 Have you set up the appropriate type(s) of print services should be supported?
Next Step
3 If you are using Novell print services, did you set up the
Novell side of network printing, such as creating print servers and attaching the print queue?
Next Step
4 If you set up Novell print services, can you see the print job using PCONSOLE or NWAdmin?
Next Step
5 Have you checked the gateway and subnet settings to make sure this equipment is part of the same network
Gateway as the client from which you are trying to print?
6 Are other services and communications performed over the network behaving in the normal and expected manner?
Next Step
End
Check the settings required for your printing environment.
Set up the NetWare server.
Refer to your Novell PCONSOLE or NWAdmin user documentation for help with using these utilities.
Set up the TCP/IP correctly.
Refer to your network documentation or use a network diagnostic utility to research a network problem.
48 Troubleshooting at Network Printing Setups
Printer driver installation error messages
Setup Needs to Copy Windows NT Files
Problem description
The wrong port type was selected from the Printer Ports dialog.
Corrective action
1. Click Cancel until the Add Printer Wizard terminates.
2. Double-click Add Printer from the Printers folder but, when prompted to select a port, choose
Local Port.
Client Software CD Now Required
Problem description
When adding a new printer driver, the end user did not choose the Have Disk option; instead, he selected the printer name from the Add Printer list.
Corrective action
1. Cancel the Add Printer Wizard.
2. Double-click Add Printer from the Printers folder but, when prompted to locate the driver, click Have Disk.
3. Select Use Existing Driver to add another copy of an existing driver or browse to the subdirectory that contains the appropriate *.inf file.
File *.DRV on Client CD Count Not Be Found
Problem description
When adding a new printer driver, the user did not choose the Have Disk option but selected the printer name from the Add Printer list.
Corrective action
1. Cancel the Add Printer Wizard.
2. Double-click Add Printer from the Printers folder, but when prompted to locate the driver, click Have Disk.
3. Browse to the subdirectory that contains the appropriate *.inf file.
Location Does Not Contain Information About Your Hardware
Problem description
The path to the *.inf file selected during driver installation is too far away. In other words, there are too many characters in the directory path.
Corrective action
Copy the directory containing the *.inf file to the local drive and resume installation.
Troubleshooting at Network Printing Setups 49
5 APPENDIX
This Port is Currently in Use
Problem description
The driver was either open, printing a job, or is in use by another printer or application, when you attempted to delete it.
Corrective action
Make sure all print jobs have completed before deleting a port. If there are still problems, exit all applications and try again. Check each driver to see if another driver is using the same port. If so, first change the driver’s port setting and delete the port.
Problem with the Current Printer Setup
Problem description
The driver was not set up properly, possibly because the installation procedure did not complete.
Corrective action
Delete the driver and reinstall it from the distribution CD-ROM.
50 Troubleshooting at Network Printing Setups
Troubleshooting
This section describes troubleshooting when you have completed the setups of network printing, as shown in the table below. (The items in this table are transcribed from other manuals (in PDF files) of this equipment.)
For troubleshooting at the time of the setups, see the following page:
P.39 “Troubleshooting at Network Printing Setups”
Transcribed from Item
Errors in hardware
General errors
Error messages on the TopAccess screen
When printing cannot be performed
Errors on client computers in Windows platform
Errors on client computers in Macintosh platform
Printer driver errors
TopAccess error messages
-
Printing Guide
Printing Guide
Setup Guide for Printing Functions
Errors in hardware
Conceivable errors in hardware are as follows:
Malfunctions of system boards, cables or connectors, or their incorrect installation
Malfunctions of the standard or optional units of this equipment, or their false operation
Damage in system software or firmware in this equipment, or their deterioration
If you assume the error comes from incorrect copying, see the Operator’s Manual for Copying
Functions to solve it.
Troubleshooting 51
5 APPENDIX
General errors
Cannot print the start page
Details
When a start page cannot be printed after the power-ON of this equipment even though start page printing has been enabled, this could be an error in the hardware. Contact our service station.
Cannot print jobs
Details
This could be an error in the software caused by the property settings of an inappropriate printer driver. However, it could be an error in the hardware when the job cannot be printed from any of the computers.
The checklist below helps you identify the cause of the error and search for more information about solving it.
NO
1
2
3
4
Check...
Is printing disabled from all the client computers connected?
Is the job monitored using print monitoring utilities, such as PCONSOLE or
Print Manager?
Can you analyze the problem by the error message and solve it?
Can you print to this equipment?
YES
Next
Step
↓
Next
Step
↓
Next
Step
↓
End
NO
⇒
⇒
⇒
⇒
For Instruction, Go To...
Refer to the following section to troubleshoot the condition:
P.43 “Equipment detection and printing check”
See the following section for troubleshooting.
P.43 “Equipment detection and printing check”
Refer to the following sections to troubleshoot the condition:
P.55 “When printing cannot be performed”
P.55 “Printer driver general errors”
P.57 “TopAccess error messages”
Contact your service representative.
52 Troubleshooting
1
2
Device status indicators (TopAccess)
You can check if this equipment requires maintenance using the TopAccess utility. In the Device tab menu, visible checking of the current status of this equipment is enabled with displayed icons when trouble has occurred in this equipment.
TopAccess Device tab menu:
1) Device status indicators
The error status of this equipment is displayed with the icon.
See the next page for the types of icons and what each icon displayed indicates.
2) Alerts
An alert message is displayed. Errors are displayed in red and warnings are displayed in yellow. See the following page for the messages to be displayed:
P.57 “TopAccess error messages”
Printer Error
The above printer error icon indicates:
- You need to remove paper from the receiving tray.
Cover Open
The Cover Open error icon indicates that you need to close the cover.
Troubleshooting 53
5 APPENDIX
Drawer Open
The Drawer Open error icon indicates that one of the drawers is opened. You must close the opened drawer to resume printing or copying.
Toner Empty
The Toner Empty icon indicates the empty status of the toner cartridge. For information on how to resolve the error condition, see “Replacing Toner Cartridge” in the Operator’s Man-
ual for Copying Functions.
Paper Empty
The Out of Paper error icon indicates the empty status of the drawer. This status does not immediately stop a print job or a copy job. If the automatic paper selection (APS) function is enabled, the print or copy job may continue by selecting paper of the same size in the other drawer. For information on how to resolve the error condition, see “When Message Lamp is
Lit/Blinking” in the Operator’s Manual for Copying Functions.
When paper has run out, you can cancel a print job in process from the control panel of this equipment. See the following page for how to cancel a print job:
Setup Guide for Printing Functions
Chapter 3 "CANCELING PRINT JOBS AND PRINTING FONT LISTS (EQUIPMENT)"
"To Cancel Print Jobs"
Paper Jam
The Paper Jam icon indicates that you must remove jammed paper from the equipment. For information on how to resolve the error condition, see “Paper Jams” in the Operator’s Man-
ual for Copying Functions.
Service calls
The Service Call error icon indicates that you must call for service. Contact your service technician.
54 Troubleshooting
When printing cannot be performed
This problem can arise as the result of a hardware malfunction, a network communication or configuration problem. Before troubleshooting the client error, ask your administrator to troubleshoot the hardware or network errors.
The following checklist helps you identify the source of the error and directs to you where you can find more information about resolving it.
Client error for Windows platform
No Check...
1 Did you mapped to the correct network port?
Yes
End
No
For Instruction, Go
To...
Client error for Macintosh platform
No Check...
1 Is this equipment you created selected in the Chooser?
Yes
End
No
For Instruction, Go
To...
Refer to “Installing the printer on Mac OS 8.6/9.x” in the Printing Guide.
Printer driver general errors
Driver Mapped to Wrong Port
Problem description
If the printer driver on a client workstation points to the wrong network port, jobs do not appear in the current jobs queue or print out.
Corrective action
1. Open the Printers folder from the Control Panel.
2. Right-click the printer driver icon.
3. Select Properties from the shortcut menu.
4. Depending on the operating system, select the following tab:
- In Windows 98/Me — Select Details. Browse to select the printer or Novell queue.
- In Windows NT 4.0/2000/XP/Server 2003 — Select Ports. Add a new port and map it to the printer.
5. Make sure that the path to the printer and the device name are correct.
\\<device name>\print
- Where <device name> is the same as the device name set from the Control Panel.
6. Click the General Tab and click Print Test Page to confirm that the settings are correct.
Troubleshooting 55
5 APPENDIX
Command Line Options Not Processed
Problem description
All print options are sent to this equipment at the start of the print job. If the print file already contains print commands, they override the command line options you set. For example, if the print file specifies the Letter media, and you specify the A4 media option with the lp command, the document is output on letter size paper (provided, of course, that all copier-related restrictions have been met).
Corrective action
Change the properties in the document you want to print and recreate the print file. Submit the print job using the LP command without setting additional parameters.
Retrieval of Printer Configuration Failed
Problem description
When accessing the printer properties, the system displayed “Retrieval of printer configuration failed”.
Corrective action
If the printer driver cannot communicate with this equipment — Verify that the system is running.
If not, turn it on. Connect to this equipment via TopAccess. If you cannot connect, reboot this equipment. If that fails, check the printer driver port assignment to make sure it is correct.
Cannot Print a Job as Expected Using PS Printer Driver
Problem description
When printing with the PS3 printer driver from the application that creates the PostScript code for printing such as Adobe Acrobat, the following print options may not work correctly.
Manual Scale
Print Paper Size
Paper Type
User Front Cover
User Back Cover
Booklet
Multiple Pages per Sheet
All options in the Effect tab
All options in the Image Quality tab
Corrective action
Disable “Use PostScript Passthrough” in the PostScript Settings dialog box and print a document.
56 Troubleshooting
Cannot Change Settings on Fonts Tab and Configuration Tab
Problem description
The Fonts Tab and Configuration tab are grayed out and they cannot be modified.
Corrective action
Users who do not have the privilege to change the printer driver setting cannot change the options in the Fonts Tab and Configuration tab. Please log in with Administrator or Power User.
TopAccess error messages
The error message will be displayed in “Alerts” field on the Device tab page of TopAccess.
TopAccess Message Corrective Action
Front Cover Open - Please Close Cover.
Close the Front Cover.
Paper Feeding Cover Open - Please Close
Cover.
Close the Paper Feeding Cover.
Transfer/Transport unit Open - Please Close
Cover.
Close the Transfer/Transport unit.
Drawer Open - Please Close Cover.
Automatic Duplexer Unit Cover Open -
Please Close Cover.
Paper Jam in Auto Duplexer Unit - Please
Clear Paper Path
Close the drawer.
Close the Automatic Duplexer Unit Cover.
Remove jammed paper.
Paper Jam in Printer - Please Clear Paper
Path
Remove jammed paper.
Paper Ejection Jam - Please Clear Paper
Path
Black Toner Empty - Please Refill.
Remove jammed paper.
Replace the black toner. Refer to the Opera-
tor’s Manual for Copying Functions for instruction.
Automatic Document Feeder Error - Please
Contact Service Technician.
Contact your service representative.
Alignment Error in Automatic Document
Feeder - Please Contact Service Technician.
Contact your service representative.
Troubleshooting 57
5 APPENDIX
TopAccess Message Corrective Action
Motor Error in Automatic Document Feeder -
Please Contact Service Technician.
Contact your service representative.
I/F Error in Automatic Document Feeder -
Please Contact Service Technician.
Contact your service representative.
Fatal Error - Please Contact Service Technician.
Contact your service representative.
Main Motor Error - Please Contact Service
Technician.
Contact your service representative.
Printer Output Error - Please Contact Service Technician.
Contact your service representative.
Printer Input Error - Please Contact Service
Technician.
Contact your service representative.
58 Troubleshooting
INDEX
D
Disclaimer notice
.......................................... 2
G
General Errors
............................................ 55
INDEX 59
60 INDEX
DP-1650/2040
OME06003900
MULTIFUNCTIONAL DIGITAL SYSTEMS
Quick Start Guide for Printing Functions
2-17-2, HIGASHIGOTANDA, SHINAGAWA-KU, TOKYO, 141-8664, JAPAN
©2006 TOSHIBA TEC CORPORATION All rights reserved
R060120B0300-TTEC
Ver B 2006-03
Advertisement
Key Features
- USB and network printing
- Network faxing
- Windows, Mac, and Unix compatibility
- Web-based management utility
- Scanning
- Email and Internet faxing