Toshiba 3000 Marine Radio User Manual

Add to my manuals

advertisement

Toshiba 3000 Marine Radio User Manual | Manualzz

Tools Required for Proper

Disassembly and Reassembly:

1. Phillips screwdriver (Size 0)

2. Phillips Screwdriver (Size 1)

3. Flat head screwdriver (5mm)

4. Hex driver (5mm)

5. Security Torx(Size8)

6. Case Separator

7. ESD Wrist Strap

8. ESD mats

9. Tweezers

TABLE OF CONTENTS:

1. BATTERY PACK REMOVAL

2. OPTIONAL PC CARD REMOVAL

3. MODULAR BAY REMOVAL

4. DVD-ROM/CDR-W DRIVE REMOVAL

5. HDD REMOVAL

6. MEMORY MODULE REMOVAL

7. KEYBOARD REMOVAL

8. CONTROL BOARD REMOVAL

9. COOLING MODULE REMOVAL

10. CPU REMOVAL

11. TOP COVER REMOVAL

12. VIDEO BOARD REMOVAL

13. MODEM BOARD REMOVAL

14. WIRELESS LAN CARD REMOVAL

15. SYSTEM BOARD REMOVAL

16. DISPLAY MASK REMOVAL

17. FL INVERTER AND LCD REMOVAL

FIELD REPLACEABLE UNIT DOCUMENTATION

Satellite TM

3000 Series

BATTERY PACK REMOVAL OPTIONAL PC CARD REMOVAL

Battery release lever

Battery pack

1. Turn the computer upside down as shown.

2. Slide the battery release lever in the direction of the

arrow.

3. Slide the battery pack forward and lift it out.

MODULAR BAY REMOVAL

PC card

Eject button

1. Push the eject button to pop it out.

2. Press the eject button and remove the PC card.

NOTE: Before removing any PCMCIA device, make

sure it is “STOPPED” in the PC Card Manager.

DVD-ROM/CDR-W DRIVE REMOVAL

DVD-ROM/CDR-W connector

DVD-ROM/CDR-W

Release lever

Select baydevice

1. Turn the computer upside down.

2. Slide the release lever in the direction of the arrow.

3. Pull out the modular bay device in the direction of the

arrow.

DVD-ROM/CDR-W bracket

M2.5x4 black screws

1. Remove four M2.5x4 black screws securing the

DVD-ROM/CDR-W to the bracket.

2. Slide the DVD-ROM/CDR-W out of the bracket.

3. Disconnect the DVD-ROM/CDR-W connector from

the drive.

TOSHIBA

Tough Enough for Today’s World

FIELD REPLACEABLE UNIT DOCUMENTATION

Satellite TM

3000 Series

HDD REMOVAL HDD REMOVAL

M3x4 silver screws

HDD bracket

HDD assy M2.5x3 black screws

1. Turn the computer upside down.

2. Remove two M2.5x3 black screws securing

HDD assembly.

3. Slide the HDD assembly in the direction of the arrow

to disconnect from the system board.

4. Lift the HDD assembly out of the HDD bay.

.

MEMORY MODULE REMOVAL

Insulator

HDD connector

5. Remove two M3x4 silver screws securing the

HDD bracket to the drive and lift off the bracket.

6. Peel off the HDD insulator.

Memory clips

Memory cover

M2x3 Black screws

1. Turn the computer upside down.

2. Remove two M2x3 black screws and remove the

memory cover.

Memory module

3. Spread the memory clips securing the memory

module and pull the memory module out of the

connector on a 45 degree angle.

TOSHIBA

Tough Enough for Today’s World

FIELD REPLACEABLE UNIT DOCUMENTATION

Satellite TM

3000 Series

KEYBOARD REMOVAL

Wireless switch

Control board cable

Display panel

JP1

Keyboard holder

Board switch

Case separator

1. Open the display panel.

2. Using the case separator, unlatch the keyboard holder

at the top of the keyboard.

KEYBOARD REMOVAL

M2.5x3 silver screws Keyboard holder

3. Disconnect the control switch/LED board cable

from the keyboard holder.

4. Remove four M2.5x3 silver screws securing the

keyboard clip.

Note: When reinstalling the keyboard holder, make sure

that the wireless switch is latch properly to the control

switch board switch.

CONTROL BOARD REMOVAL

Keyboard

Control switch board

IPS switch cable

Keyboard cable JP5 JP4

4. Lift out the keyboard and set it as shown above.

5 Disconnect the keyboard cable from JP5 and IPS switch

cable from JP4 on the video board and lift out the

keyboard.

M2.5x3 black screws

1. Remove four M2.5x3 black screws securing the

control switch board.

2. Disconnect the control switch/LED board from JP4

on the main PCB.

TOSHIBA

Tough Enough for Today’s World

FIELD REPLACEABLE UNIT DOCUMENTATION

Satellite TM

3000 Series

COOLING MODULE REMOVAL

M2.5x3 black screws

Heatsink cover

Heatsink

1. Remove four M2.5x3 brass screws securing the

heatsink cover.

Silver screws

2. Remove four silver screws securing the heatsink.

3. Lift out the heatsink.

CPU REMOVAL TOP COVER REMOVAL

CPU

Open

CPU lock

Lock

Flat head screwdriver

1. Using a 5mm flat head screw driver, insert the screwdriver

into the CPU lock slot and turn it counterclockwise.

2. Lift out the CPU.

M2.5x3 black screw Cable cover

1. Remove one M2.5x3 flat head screw securing the

cable cover.

NOTE: In order to properly lock the CPU, a 5mm flat

head screw driver must be used.

TOSHIBA

Tough Enough for Today’s World

FIELD REPLACEABLE UNIT DOCUMENTATION

Satellite TM

3000 Series

TOP COVER REMOVAL

LCD/FL cable

M2.5x15 silver flat head screw

Grey coax cable

IPS switch cable Black coax cable

2. Turn the computer right side up and open the display panel.

3. Disconnect the following four cables:

- Black and Gray coax cables

- IPS switch cable from PJ1

4. Remove one M2.5x15 silver flat head screws securing

the LCD/FL cable and disconnect the LCD/FL cable.

M2.5x6 black screws

5. Remove six M2.5x6 black screws

(four at the back and two at the bottom cover)

securing the display assembly.

6. Lift out the display assembly.

M2.5x3 black screw

M2.5x6

black screw

M2.5x18

black screws

M2.5x5 silver screws

7 Remove the following thirteen screws from the bottom

cover:

- M2.5x6 black screw

- M2.5x18 black screws

M2.5x14 black screw M2.5x14 torx screw

8. Remove the following 9 screws from the top cover:

- Six M2.5x3 black screws

- One M2.5x14 black screw

- One M2.5x14 Torx screw(Size 8)

- One M2.5x5 silver screws

9. Unlatch the top cover from the bottom cover.

TOSHIBA

Tough Enough for Today’s World

FIELD REPLACEABLE UNIT DOCUMENTATION

Satellite TM

3000 Series

MODEM BOARD REMOVAL VIDEO BOARD REMOVAL

JP8

Video board

JP11 System board

1. Disconnect the video board from JP8 and JP11 on

the system board.

WIRELESS LAN CARD REMOVAL

RJ11 cable Modem board JP13

1. Disconnect the modem board from JP13 on the

system board.

2. Disconnect the RJ11 cable from the modem board.

Mini PCI

Clips

Wireless LAN card

1. Push the Mini PCI slot clips outward and pull the

Wireless LAN card out of the connector on a

30 degree angle.

TOSHIBA

Tough Enough for Today’s World

FIELD REPLACEABLE UNIT DOCUMENTATION

Satellite TM

3000 Series

SYSTEM BOARD REMOVAL

Hex screws

Stud screws

M2.5x4 brass screws Metal shield

1. Remove the following eleven screws securing the

system board:

- 2 M2.5x4 brass screws securing the metal shield

- 5 M2.5x4 brass screws securing the HDD shield

- 1 M2.5x4 brass screw on the system board

- 4 stud screws from the CPU socket

System board

2. Remove four hex screws at the back of the computer

securing the system board.

3. Lift out the system board.

TOSHIBA

Tough Enough for Today’s World

FIELD REPLACEABLE UNIT DOCUMENTATION

Satellite TM

3000 Series

14” DISPLAY MASK REMOVAL FL INVERTER AND 14” LCD REMOVAL

LCD module

Latch

Display mask

LCD

Mask seals

1. Remove two rubber seals at the top corners of the

display assembly and two mask seals at the bottom

corners of the display assembly.

2. Remove

four M2.5x5 silver screws securing the display

mask.

3. There are 21 latches securing the display mask.

Carefully insert your fingers between the display mask

and the LCD module and pry open the latches starting

from the bottom six latches, to the five latches on the

right and left sides, ending with the top six latches.

LCD/

FL cable

FL inverter board

Tape

M2x4 brass screws FL cable

1. Peel off the tape securing the FL cable.

2. Remove two M2.5x5 silver screw securing

FL inverter board.

3. Carefully lift up the FL inverter board and disconnect

the LCD/FL cable from CN1 and the FL cable

from CN2.

4. Remove two 2.5x6 black screws securing the LCD

top cover.

M2x3 silver screws

LCD/FL cable

5. Lay the top cover as shown above.

6. Peel off two capton tapes securing the LCD/FL cable

and disconnect the cable.

7. Remove four M2x3 silver screws securing the LCD

module to the LCD brackets and lift out the module.

NOTE: When you open and close the display assembly

with the top cover off, hold it by the hinges to

prevent the brackets from bending.

TOSHIBA

Tough Enough for Today’s World

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement