advertisement
HM66_EN.book Page 1 Thursday, February 23, 2006 2:49 PM
Integrated High Definition
DLP
™
Projection Television
HIGH-DEFINITION TELEVISION
50HM66
56HM66
IMPORTANT NOTE
Before connecting, operating, or adjusting this product, carefully read the Important Safety, Installation, Care, and Service information in the Installation Guide.
For an overview of steps for setting up your new TV, see page 4.
Note: To display a High Definition picture, the TV must be receiving a
High Definition signal (such as an over-the-air High Definition TV broadcast, a High Definition digital cable program, or a High Definition digital satellite program). For details, please contact your TV antenna installer, cable provider, or satellite provider.
Note: If the TV is powered off and then quickly on again when the lamp unit is hot, it may take several minutes for the picture to appear on-screen. This is a property of DLP
TM
TV lamp technology and is NOT a sign of malfunction. For details, see "IMPORTANT NOTICE ABOUT
HOT LAMP RESTART" on page 2.
© 2006 TOSHIBA CORPORATION
All Rights Reserved
A
IB
AM
ER
ICA
CONSUMER PR
OD
UC
TS
IS
O
1400
1 FILE No.
A9
64
5
Owner’s Record
The model number and serial number are on the back of your TV. Record these numbers in the spaces below.
Refer to these numbers whenever you communicate with your Toshiba dealer about this TV.
Model number:
Serial number:
YC/N
VX1A00001000
HM66 (E/F) Web 213:276
HM66_EN.book Page 2 Thursday, February 23, 2006 2:49 PM
CAUTION: This television is for use only with the Toshiba stand indicated below. Use with other carts or stands is capable of resulting in instability, causing possible injury.
Television Stand Model
50HM66 ST5066
56HM66 ST5666
Welcome to Toshiba
Thank you for purchasing this Toshiba TV, one of the most innovative DLP™ projection TVs on the market. We have provided two separate guides to facilitate the installation and operation of your TV.
Please use the Guides in the order shown below to get the most enjoyment from your new TV.
• The “Installation Guide” explains how to connect your TV to your antenna and equipment.
• The “Operating Guide” (this Guide) provides step-by-step instructions for using your TV’s many features.
7) This TV contains several cooling fans to moderate the internal temperature. You may be able to hear the fans for several minutes after the TV is turned off.
This is a function of the Quick Restart™ feature and is not a sign of TV malfunction. You can set the Quick Restart™ feature to stop the fans as soon as the TV is powered off. See “Setting the Quick Restart™ feature”
(- page 20).
8) The yellow and blue LED lights at the bottom center of the
TV front indicate your TV’s current status. If either light flashes, see “LED indications” (- page 46).
9) Every time the TV power cord is plugged in, the yellow LED will blink until the TV enters standby mode (plugged in but not powered on). This is normal and is not a sign of malfunction.
“Voice announce” feature
When certain non-standard conditions occur, the LEDs on the TV will blink and the TV will play a recorded
“voice announcement” describing the condition (see the
LED indication table on page 46 for the specific conditions that include a voice announcement).
To repeat the voice announcement and hear additional information, press the MENU button on the TV while the
LEDs are blinking.
Important notes about your
DLP™ projection TV
1) The light source for this TV is a projection lamp unit with a limited service life. When the lamp wears out, the picture may become dark or black or the lamp may fail, at which time you must replace the lamp unit. See “Lamp unit replacement and care” (- pages 47–49).
2) When the lamp mode is set to Low Power, every time the
TV is powered on, the lamp will initially be in High Bright mode but will switch to Low Power mode after a short period of time. You may notice a change in screen brightness when this happens. This is normal and is not a sign of malfunction.
(- page 42 for details.)
3) Every time the TV is powered on, it may take several minutes for the picture to obtain full brightness (- IMPORTANT
NOTICE ABOUT “HOT LAMP RESTART,” at right).
4) The TV’s display is manufactured using an extremely high level of precision technology; however, an occasional pixel
(dot of light) may show constantly on the screen. This is a structural property of DLP™ (Digital Light Processing™) technology and is not a sign of malfunction. Such pixels are not visible when the picture is viewed from a normal viewing distance.
5) Always sit approximately 10–25 feet away from the TV and as directly in front of it as possible. The picture quality may be affected by your viewing position and length of viewing time. If you sit too closely to the TV for too long, you may suffer from eye fatigue. See item 29 of the “care” information in the separate Installation Guide.
6) Depending on the media you are viewing, it is possible, although unlikely, that a limited number of viewers may see a “rainbow effect” on the screen, which can, in rare instances, result in eye fatigue. This is a rare occurrence related to DLP technology and is not a sign of TV malfunction.
IMPORTANT NOTICE ABOUT “HOT LAMP RESTART”
When the TV has been powered on long enough for the lamp unit to get hot, it may take several minutes for the picture to appear on-screen in the following situations:
• When the Quick Restart™ feature is set to OFF and you turn the TV off and then on again within a few minutes; or
• If the TV is on when a short-term power failure, power surge, or other similar power failure occurs, such that the TV loses and regains power within a few minutes.
This is a property of DLP TV lamp technology and is
NOT a sign of malfunction.
If this occurs, the yellow LED on the TV front panel will blink
(and the blue LED will be lit solid) until the TV is finished restarting the lamp and the normal picture appears. If both
LEDs are blinking, you will need to turn the TV off and then on again to restart the lamp.
Trademark Information
• This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use of this copyright protection technology must be authorized by
Macrovision, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision. Reverse engineering or disassembly is prohibited.
• WOW, SRS and l symbol are trademarks of SRS Labs, Inc.
WOW technology is incorporated under license from SRS Labs, Inc.
• *Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are registered trademarks of Dolby
Laboratories.
• CableCARD™ is a trademark of Cable Television Laboratories, Inc.
• HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.
• Digital Light Processing™, DLP™ and the DLP™ medallion are trademarks of Texas Instruments.
2
HM66 (E/F) Web 213:276
HM66_EN.book Page 3 Thursday, February 23, 2006 2:49 PM
Contents
Chapter 1: Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Features of your new TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Overview of steps for installing, setting up, and using your new TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
TV front and side panel controls and connections . . . . . . . . . 5
TV back panel connections. . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Chapter 2: Using the remote control . . . . . . . . . . . . . . . . . . . 7
Preparing the remote control for use. . . . . . . . . . . . . . . . . . . . 7
Installing the remote control batteries . . . . . . . . . . . . . . . . . . 7
Remote control effective range. . . . . . . . . . . . . . . . . . . . . . . . 7
Learning about the remote control . . . . . . . . . . . . . . . . . . . . . 8
Using the remote control to control your other devices . . . . . 9
Remote Control functional key chart . . . . . . . . . . . . . . . . . . 10
Programming the remote control to control your other devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Remote control codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Chapter 3: Menu layout and navigation . . . . . . . . . . . . . . . . .14
Main menu layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Setup/Installation menu layout . . . . . . . . . . . . . . . . . . . . . . . 15
Navigating the menu system. . . . . . . . . . . . . . . . . . . . . . . . . 15
Chapter 4: Setting up your TV . . . . . . . . . . . . . . . . . . . . . . . .16
Selecting the menu language . . . . . . . . . . . . . . . . . . . . . . . . 16
Configuring the antenna input sources for the ANT 1 and ANT 2 terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Programming channels into the TV’s channel memory . . . . 17
Programming channels automatically . . . . . . . . . . . . . . 17
Manually adding and deleting channels in the channel memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Programming your favorite channels . . . . . . . . . . . . . . . . . . 18
Setting the ColorStream HD audio mode . . . . . . . . . . . . . . . 20
Setting the HDMI™ audio mode . . . . . . . . . . . . . . . . . . . . . 20
Viewing the CableCARD™ menu . . . . . . . . . . . . . . . . . . . . 20
Setting the Quick Restart™ feature . . . . . . . . . . . . . . . . . . . 20
Viewing the digital signal meter . . . . . . . . . . . . . . . . . . . . . . 21
Viewing the system status. . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Chapter 5: Using the TV’s basic features . . . . . . . . . . . . . . . .23
Selecting the video input source to view . . . . . . . . . . . . . . . 23
Labeling the video input sources . . . . . . . . . . . . . . . . . . . . . 23
Tuning channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Using the Channel Browser™ . . . . . . . . . . . . . . . . . . . . 24
Tuning your favorite channels . . . . . . . . . . . . . . . . . . . . 26
Tuning to the next programmed channel . . . . . . . . . . . . 26
Tuning to a specific channel (programmed or unprogrammed) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Switching between two channels using Channel
Return . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Switching between two channels using SurfLock™ . . . 26
Selecting the picture size . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Scrolling the TheaterWide
®
picture (TheaterWide 2 and 3 only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Using the auto aspect ratio feature . . . . . . . . . . . . . . . . . . . . 29
Selecting the cinema mode
(480i signals only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Adjusting the picture. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Selecting the picture mode . . . . . . . . . . . . . . . . . . . . . . . 30
Adjusting the picture quality . . . . . . . . . . . . . . . . . . . . . 30
Using the closed caption mode . . . . . . . . . . . . . . . . . . . . . . . 31
Closed Caption Advanced . . . . . . . . . . . . . . . . . . . . . . . 31
Digital closed captions . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Adjusting the audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Muting the sound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Using the digital audio selector . . . . . . . . . . . . . . . . . . . 32
Selecting stereo/SAP broadcasts . . . . . . . . . . . . . . . . . . 33
Adjusting the audio quality . . . . . . . . . . . . . . . . . . . . . . 33
Using the StableSound
®
feature. . . . . . . . . . . . . . . . . . . 34
Turning off the built-in speakers . . . . . . . . . . . . . . . . . . 34
Selecting the optical audio output format . . . . . . . . . . . 34
Using the Locks menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Entering the PIN code . . . . . . . . . . . . . . . . . . . . . . . . . . 35
If you cannot remember your PIN code. . . . . . . . . . . . . 35
Changing your PIN code . . . . . . . . . . . . . . . . . . . . . . . . 35
Blocking TV programs and movies by rating (V-Chip) . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Blocking channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Unlocking programs temporarily . . . . . . . . . . . . . . . . . . 38
Using the input lock feature . . . . . . . . . . . . . . . . . . . . . . 38
Using the control panel lock feature . . . . . . . . . . . . . . . 39
Setting the sleep timer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Displaying TV setting information on-screen using
RECALL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Understanding the auto power off feature . . . . . . . . . . . . . . 40
Understanding the last mode memory feature . . . . . . . . . . . 40
Chapter 6: Using the TV’s advanced features . . . . . . . . . . . . . 41
Using the advanced picture settings features . . . . . . . . . . . . 41
Using dynamic contrast . . . . . . . . . . . . . . . . . . . . . . . . . 41
Using CableClear
®
/DNR (digital noise reduction) . . . . 41
Using MPEG noise reduction. . . . . . . . . . . . . . . . . . . . . 41
Selecting the color temperature . . . . . . . . . . . . . . . . . . . 42
Selecting the lamp mode . . . . . . . . . . . . . . . . . . . . . . . . 42
Using the Game Mode feature . . . . . . . . . . . . . . . . . . . . 43
Using the advanced audio settings features . . . . . . . . . . . . . 43
Using the SRS WOW™ surround sound feature . . . . . . 43
Chapter 7: Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . 44
General troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
LED indications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Chapter 8: Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Lamp unit replacement and care . . . . . . . . . . . . . . . . . . . . . . 47
Replacing the lamp unit
(User-replaceable component). . . . . . . . . . . . . . . . . 47
When to replace the lamp unit . . . . . . . . . . . . . . . . . . . . 47
How to replace the lamp unit . . . . . . . . . . . . . . . . . . . . . 48
Disposing of the used lamp unit. . . . . . . . . . . . . . . . . . . 49
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Limited United States Warranty for DLP™ Television Models . . . . . . . . . . . . . . . . . . . . 51
Limited Canada Warranty for DLP™ Television Models . . . . . . . . . . . . . . . . . . . . 52
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
3
HM66 (E/F) Web 213:276
HM66_EN.book Page 4 Thursday, February 23, 2006 2:49 PM
Chapter 1: Introduction
NOTICE OF POSSIBLE TV STAND INSTABILITY
DANGER: RISK OF SERIOUS PERSONAL
INJURY OR DEATH! Use this TV only with the TOSHIBA TV stand listed in the
“Specifications” section of this manual. Use with other stands may result in instability, causing possible injury or death.
CAUTION:This television is for use only with the Toshiba stand indicated below. Use with other carts or stands is capable of resulting in instability, causing possible injury.
Television Stand Model
50HM66
56HM66
ST5066
ST5666
Features of your new TV
The following are just a few of the many exciting features of your new Toshiba widescreen, integrated HD, DLP™ projection TV:
•
•
•
•
•
•
•
Integrated digital tuning (8VSB ATSC and QAM) eliminates the need for a separate digital converter set-top box (in most cases).
Digital CableCARD™ slot for viewing encrypted digital
Cable TV programs (- Installation Guide).
Two HDMI™ digital, high-definition multimedia interfaces (- Installation Guide).
Two sets of ColorStream
®
HD high-resolution component video inputs (- Installation Guide).
SRS WOW™ (- page 43), audio technologies.
Digital Audio Out optical audio connection with Dolby
®
Digital optical output format (- page 34; also see
Installation Guide).
CableClear
®
DNR digital picture noise reduction
(- page 41).
“Voice announce” feature
When certain non-standard conditions occur, the LEDs on the TV will blink and the TV will play a recorded
“voice announcement” describing the condition (see the
LED indication table on page 46 for the specific conditions that include a voice announcement).
To repeat the voice announcement and hear additional information, press the MENU button on the TV while the
LEDs are blinking.
Overview of steps for installing, setting up, and using your new TV
Follow these steps to set up your TV and begin using its many exciting features.
1
Carefully read the important safety, installation, care, and service information in the separate Installation Guide.
Keep this manual for future reference.
2
Observe the following when choosing a location for the
TV:
•
•
•
•
•
Read the separate Installation Guide.
Read “Important notes about your DLP™ projection
TV” (- page 2).
Place the TV on the applicable optional TV stand listed in the “Specifications” section (if available for this TV model) or on a sturdy, level, stable surface that can safely support the size and weight of the unit.
Place the TV in a location where light does not reflect on the screen.
Place the TV far enough from walls and other objects to allow proper ventilation. Inadequate ventilation may cause overheating, which will damage the TV. THIS
TYPE OF DAMAGE IS NOT COVERED UNDER
THE TOSHIBA WARRANTY.
3
Do not plug in any power cords until AFTER you have connected all cables and devices to your TV.
4
BEFORE connecting cables or devices to the TV, learn the functions of the TV’s connections and controls
(
-
pages 5-6).
5
Connect your other electronic device(s) to the TV
(
-
Installation Guide).
6
Install the batteries in the remote control (
-
page 7).
7
See “Learning about the remote control” (
-
page 8) for an overview of the buttons on the remote control.
8
Program the remote control to operate your other device(s) (
-
pages 9–13).
9
AFTER connecting all cables and devices, plug in the power cords for your TV and other devices.
10
After you plug in the TV power cord, the yellow LED
(on the TV front ) will blink 3 times. Wait several seconds until the yellow LED stops blinking and then press p on the TV or remote control.
See “LED indications” (- page 46).
11
See “Menu layout and navigation” for a quick overview of navigating the TV’s menu system (
-
page 14).
12
Program channels into the TV’s channel memory
(
-
page 17).
13
For details on using the TV’s features, see Chapters 5 and 6.
14
For help, refer to the Troubleshooting Guide
(
-
Chapter 7).
15
For lamp unit replacement instructions, see Chapter 8.
16
For technical specifications and warranty information, see
Chapter 8.
17
Enjoy your new TV!
4
HM66 (E/F) Web 213:276
HM66_EN.book Page 5 Thursday, February 23, 2006 2:49 PM
Chapter 1: Introduction
TV front and side panel controls and connections
Front of TV
Right side of TV
1
3
7*
2
4
10
8
5
6
9
1
Remote sensor (behind the screen) — Point the remote control toward this area of the TV screen. See “Remote control effective range” (- page 7).
2
Blue, Yellow and Green/Red LEDs
See “LED indications” (- page 46) for additional information.
3
POWER — Press to turn the TV on and off.
If the TV stops responding to the controls on the remote control or TV control panel and you cannot turn off the
TV, press and hold the POWER button on the TV control panel for 5 or more seconds to reset the TV.
4
CHANNEL U u — When no menu is on-screen, these buttons change the channel (programmed channels only;
- page 17). When a menu is on-screen, these buttons function as up/down menu navigation buttons.
5
VOLUME + – — When no menu is on-screen, these buttons adjust the volume level. When a menu is onscreen, these buttons function as left/right menu navigation buttons.
6
INPUT — Repeatedly press to change the source you are viewing (ANT 1, VIDEO 1, VIDEO 2,
ColorStream HD-1, ColorStream HD-2, HDMI 1,
HDMI 2, ANT 2).
Control panel Side panel
7
*MENU (ENTER) — Press to access the menu system
(- pages 14–15). When a menu is on-screen, the MENU button on the TV’s side control panel functions as the
Enter button.
8
ARROWS BbC c — When a menu is on-screen, these buttons function as up/down/left/right menu navigation buttons.
9
EXIT — Press to instantly close an on-screen menu.
10 VIDEO-2 IN — The side panel A/V connections are referred to as “VIDEO 2” and include standard A/V connections plus optional S-video.
5
HM66 (E/F) Web 213:276
HM66_EN.book Page 6 Thursday, February 23, 2006 2:49 PM
Chapter 1: Introduction
TV back panel connections
For an explanation of cable types and connections, see the Installation Guide.
1 2 3 4 5
6 7
8 9
1
VIDEO 1 IN — Standard (composite) video and standard audio inputs plus optional S-video inputs for connecting devices with composite video or S-video output.
Note: Standard (composite) video and S-video cables carry only video information; separate audio cables are required for a complete connection.
2
ColorStream
®
HD-1 and ColorStream
®
HD-2 —
Two sets of ColorStream
®
high-definition component video inputs (with standard stereo audio inputs) for connecting devices with component video output, such as a Toshiba DVD player with ColorStream
®
.
Note: Component video cables carry only video information; separate audio cables are required for a complete connection.
ColorStream
®
HD-1 and ColorStream
®
HD-2
Audio IN — ColorStream HD-1/2 audio input terminals are shared with HDMI 1/2 analog audio input terminals, and their use can be configured in the Setup menu
(- “Setting the ColorStream HD audio mode” page 20).
3
Variable Audio OUT — Standard analog audio outputs for connecting an analog amplifier with external speakers.
4
A/V OUT — Standard composite video and analog audio outputs for connecting a VCR for editing and dubbing.
5
IR OUT — For controlling infrared remote-controlled devices through the TV. You can connect up to two devices with an IR blaster cable, and then control the devices using the TV’s IR pass-through features.
6
6
ANT 1 and ANT 2 — Two inputs that support analog
(NTSC) and digital (ATSC) off-air antenna signals and analog and digital (QAM) Cable TV signals.
Note: If you have an antenna only, connect it to ANT 1. If you have both cable TV and an antenna, connect the cable TV to ANT 1 and the antenna to ANT 2.
7
HDMI™ 1 and 2 IN — Two High-Definition Multimedia
Interface inputs receive digital audio and uncompressed digital video from an HDMI device or uncompressed digital video from a DVI device. Also see item 2.
8
Digital Audio OUT — Optical audio output in Dolby
Digital or PCM (pulse-code modulation) format for connecting an external Dolby Digital decoder, amplifier,
A/V receiver, or home theater system with optical audio input.
9
CableCARD™ slot — For use with a digital security card and digital cable TV service (provided by your local cable operator) to view encrypted digital programming
(- page 20).
HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.
CableCARD is a trademark of Cable Television Laboratories, Inc.
HM66 (E/F) Web 213:276
HM66_EN.book Page 7 Thursday, February 23, 2006 2:49 PM
Chapter 2: Using the remote control
Preparing the remote control for use
Your TV remote control can operate your TV and many other devices such as cable converter boxes, satellite receivers,
VCRs, DVD players, and HTIBs (home theater in a box), even if they are different brands.
If you have a Toshiba device:
Your TV remote control is preprogrammed to operate most
Toshiba devices (- page 11).
If you have a non-Toshiba device or a Toshiba device that the remote control is not preprogrammed to operate:
You can program the TV remote control so it will operate the other device (- pages 9–13).
• Always remove batteries from remote control if they are
dead or if the remote control is not to be used for an extended period of time. This will prevent battery acid from leaking into the battery compartment.
Remote control effective range
For optimum performance, aim the remote control directly at the TV and make sure there is no obstruction between the remote control and the TV.
Point remote control toward remote sensor on front of TV.
Installing the remote control batteries
1
Remove the battery cover from the back of the remote control.
Squeeze tab and lift cover.
2
Install two “AAA” size batteries, making sure to match the + and – signs on the batteries to the signs on the battery compartment.
16.4 ft (5m)
3
Reinsert the battery cover in the remote control until the tab snaps.
Caution: Never throw batteries into a fire.
Notes:
• Be sure to use AAA size batteries.
• Dispose of batteries in a designated disposal area.
• Batteries should always be disposed of with the
environment in mind. Always dispose of batteries in accordance with applicable laws and regulations.
• If the remote control does not operate correctly, or if the
operating range becomes reduced, replace batteries with new ones.
• When necessary to replace batteries in the remote control,
always replace both batteries with new ones. Never mix battery types or use new and used batteries in combination.
7
HM66 (E/F) Web 213:276
HM66_EN.book Page 8 Thursday, February 23, 2006 2:49 PM
Chapter 2: Using the remote control
Learning about the remote control
The buttons used for operating the TV only are described here.
For a complete list of the remote control’s functions, see the remote control functional key chart (- page 10).
1
POWER turns the TV on and off. Press p to turn on the
TV. The blue LED indicator on the TV front will be illuminated. Press p again to turn off the TV.
Note: The Quick Restart™ setting will affect the amount of time it takes for the picture to appear when you turn on the
TV (
- page 20).
2
FREEZE freezes the picture. Press again to restore the moving picture.
3
SLEEP accesses the sleep timer ( page 39).
4
PIC SIZE cycles through the five pictures sizes: Natural,
TheaterWide 1/2/3, and Full ( page 27).
5
Channel Numbers (0–9, –/100) directly tune channels. The “–” button is used to tune digital channels
(
-
page 26) or to display the favorite channel list
( page 19).
6
INPUT selects the video input source ( -
page 23).
7
CH Bb cycles through programmed channels when no menu is on-screen (
-
page 17) and functions as page up/ down when a menu is on-screen.
8
VOL + – adjusts the volume level.
9
HOME (~) accesses the home function of the Channel
Browser™ feature (- page 26).
10 RECALL displays TV setting information on-screen
(- page 40).
11 CH RTN returns to the last viewed channel (- page 26).
12 MUTE reduces or turns off the sound (- page 32).
13
3 C / # c While watching TV, these buttons open the
Channel Browser™ banner and tune to the previous/next channel in the channel history (- page 24). (Also see
“Arrow buttons”.)
14 Arrow buttons (
BbC c) When a menu is on-screen, these buttons select or adjust programming menus. (Also see 3 C / # c.)
15 FAV Bb tunes to the next higher/lower favorite channel
(- page 19).
16 ENTER activates highlighted items in the main menu system.
17 MENU accesses the main TV menu system (
-
pages 14 and 15).
18 EXIT closes on-screen menus.
19 MODE SELECT Switch switches between TV,
CABLE/SAT, DVD, and VCR modes (
-
page 9). Set to
“TV” to control the TV.
Note: The error message “NOT AVAILABLE” may appear if you press a key for a function that is not available.
8
HM66 (E/F) Web 213:276
HM66_EN.book Page 9 Thursday, February 23, 2006 2:49 PM
Chapter 2: Using the remote control
Using the remote control to control your other devices
If you have a non-Toshiba device or a Toshiba device that the remote control is not preprogrammed to operate, you must first program the remote control to recognize the device (if you have not already done so) (- pages 11–13).
•
•
•
To use your TV remote control to operate a:
Cable converter box or satellite receiver, set the MODE
SELECT Switch to CABLE/SAT.
VCR, set the MODE SELECT Switch to VCR.
DVD player or HTIB, set the MODE SELECT Switch to
DVD.
Note: Even after the TV remote control is programmed, it may not operate certain features on your other device. If this happens and you wish to use those features, you will need to use the device’s original remote control.
Point the remote control directly at the device.
1
POWER Turns the selected device on and off.
2
Channel Numbers (0-9) Press to directly access channels (as opposed to < ,).
3
+10 Press to directly access DVD chapters higher than 10.
4
CH Bb
B selects the next higher channel; b selects the next lower channel (for channels programmed into memory only).
5
GUIDE Displays channel guide.
6
INFO Displays TV status information on-screen.
7
BbC c Press to navigate DVD menus (may not work on some DVD players).
8
ENTER Required by some satellite receivers and DVD players.
9
DVD CLEAR Press to reset the title and chapter number.
10 PLAY Begins playback of a tape or DVD.
11 PAUSE Press during play or record mode to pause the picture; press again to restart.
12 STOP Stops the tape or DVD.
13 SKIP
z Skips forward to locate later DVD chapters.
14 FF Fast-forwards the tape or DVD. (Press during play mode to view the picture moving rapidly forward.)
15 SKIP
Z Skips back to beginning of current DVD chapter or locates previous chapters.
16 REW Rewinds/reverses the tape or DVD. (Press during play mode to view the picture moving rapidly backward.)
17 TV/VCR To view one program while recording another, press to select TV mode.
18 REC Starts tape recording.
19 TOP MENU Accesses a DVD’s top menu.
20 SET UP Accesses a DVD’s setup menu.
21 MODE SELECT Switch Set to “TV” to control the TV;
“CABLE/SAT” to control a cable converter box or satellite receiver; “DVD” to control a DVD player or
HTIB; “VCR” to control a VCR.
9
HM66 (E/F) Web 213:276
HM66_EN.book Page 10 Thursday, February 23, 2006 2:49 PM
Chapter 2: Using the remote control
Remote Control functional key chart
Notes:
• “---” = key does not send a signal in that remote control mode.
• sTV = key will affect the TV, even when the remote control is not in the “TV” device mode.
REMOTE CONTROL KEY
POWER
SLEEP
INPUT
1-9
0
100/–/+10
RECALL
CH RTN
INFO
MENU
Bb/FAVBb
C c
3
#
ENTER
EXIT/DVD CLEAR
VOL + –
CH
Bb
PIC SIZE
MUTE
GUIDE
FF
PAUSE/STEP
PLAY
REW
HOME
STOP
FREEZE
SKIP Z
SKIP z
TV/VCR
REC
SET UP
TOP MENU
Toshiba TV (TV)
Power
Sleep timer
TV/Video select
Digit 1-9
Digit 0
– (sub channel)
RECALL
Previous channel
---
Menu/DVD Menu
Menu select/
FAV up/down
Menu select/
Channel Browser™
Menu select/
Channel Browser™
Enter
Exit
Volume up/down
Channel up/down
Picture size
Sound mute
---
---
---
---
---
Channel Browser™
Home
---
---
---
---
---
Freeze picture
---
---
---
---
---
---
---
---
---
---
---
---
---
---
CABLE
Power s TV s TV
Digit 1-9
Digit 0
--s TV
---
---
---
---
--s TV
Channel up/down s TV s TV
---
--s TV
---
---
SAT (satellite) VCR
---
---
---
---
Power s TV s TV
Digit 1-9
Digit 0
– (sub CH) s TV
---
Info
Menu
Menu up/down
Menu left
Menu right
---
---
---
---
Select Enter
Exit s TV
Channel up/down s TV s TV
SAT Guide
---
--s TV
---
---
Power s TV s TV
Digit 1-9
Digit 0
100
Display
---
---
---
---
---
---
---
--s TV
Channel up/down s TV s TV
---
Fast FWD
Pause
Play
Rewind
---
Stop s TV
---
---
TV/VCR
Record (2 click)
---
---
Menu right
Enter
DVD Clear s TV
--s TV s TV
---
Fast FWD
Pause
Play
Rewind
---
Stop s TV
Skip REV
Skip FWD
---
---
DVD Setup
Top Menu
DVD
Power s TV s TV
Digit 1-9
Digit 0
+10 s TV
---
---
DVD Menu
Menu up/down
Menu left
10
HM66 (E/F) Web 213:276
HM66_EN.book Page 11 Thursday, February 23, 2006 2:49 PM
Chapter 2: Using the remote control
Programming the remote control to control your other devices
Your Toshiba TV remote control is preprogrammed to operate most Toshiba devices. To program your TV remote control to operate a non-Toshiba device (or a Toshiba device that it is not preprogrammed to operate), follow the steps below. For details on using the remote control to operate the device, see page 9.
1
In the remote control code table (- page 12), find the code for your device. If more than one code is listed, try each one separately until you find one that works.
2
Set the MODE SELECT Switch to the type of device you are programming the remote control to operate —
CABLE/SAT (for a cable converter box or satellite receiver), DVD (for a DVD player or HTIB [home theater in a box]), or VCR (for a VCR or TV/VCR combo).
3
While holding down E, press the Channel Number buttons to enter the 3-digit code for your device.
4
To test the code, turn on the device, point the remote control at it, and press p. See notes below.
•
If the correct code was entered, the device will turn off.
•
If the device does not respond, repeat steps 1–4 using another code.
•
If the device does not respond to another code, you will need to use the remote control that came with the device.
5
Remember to set the MODE SELECT Switch back to TV to control the TV.
6
For future reference, write down the code(s) you used:
DEVICE CODE DEVICE CODE
Notes:
• In addition to POWER, confirm that all necessary keys on the
TV remote control operate your device. If some keys are not operational, repeat the device code setup using another code (if other codes are listed for your device). If, after trying all listed codes, the necessary keys do not operate your device, use the device’s original remote control.
• Every time you change the batteries, you will need to
reprogram the remote control.
• Some newer VCRs respond to either of two codes. These
VCRs have a switch labeled “VCR1/VCR2.” If your VCR has this kind of switch and does not respond to the codes for your VCR brand, set the switch to the other position (“VCR1” or “VCR2”) and reprogram the remote control.
11
HM66 (E/F) Web 213:276
HM66_EN.book Page 12 Thursday, February 23, 2006 2:49 PM
Chapter 2: Using the remote control
Remote control codes
In some cases you may not be able to operate your device with the TV remote control. Your other device may use a code that is not recognized by the
TV remote control. If this happens, use the device’s remote control.
Cable converter box
ABC
Archer
Cableview
Century
Citizen
Contec
Diamond
Eagle
GE
Gemini
General Instruments
Hamlin
Hitachi
Jasco
Jerrold
Magnavox
Memorex
Multi Canal
Novavision
Panasonic
Philco
Philips
Pioneer
Proscan
Radio Shack
RCA
Realistic
Recoton
Samsung
Scientific Atlanta
Sears
Signature
Signature 2000
Sprucer
Starcom
Stargate
Sylvania
TeleView
Texscan
Tocom
U. S. Electronics
United Cable
Universal
Wards
061, 062, 063, 082,
084, 087, 091, 092,
096, 098
065, 092, 097, 099
064, 094
092
090, 092, 097
083, 085, 086, 088,
093, 098
093
091
061, 062
069, 070, 094
062, 089, 096
093
062, 095, 096
097
062, 069, 071, 082,
086, 089, 091, 096
072, 096
091, 092, 104
090
101
081, 083, 085
087
066, 067, 068, 070,
072, 073, 074, 075,
091, 092
076, 077
061, 062
092, 097, 099
064, 081
065
102
077, 090
063, 078, 079, 080,
088, 098, 101, 105
095
062
096
081, 085
069, 082, 087, 096,
103, 104
069, 090
095, 100
090
100
071, 084, 085
087, 096, 098
082
065, 092, 097, 099,
102, 103
096
Satellite receiver
Alphastar
Chaparral
DISH Network
038, 059
034
057
12
Drake
Echostar
Express Vu
Fujitsu
GE
General Instruments
Hitachi
Hughes
Hughes Network
Systems
Intersat
Janeil
JVC
Kenwood
Magnavox
Optimus
Pansat
Primestar
Proscan
Radio Shack
RCA
Realistic
Samsung
Sony
Star Choice
Star Trak
STS
Toshiba
Uniden
Zenith
TV/VCR Combo
Action
GE
Goldstar
Panasonic
Precision
Quasar
Realistic
Sony
Toshiba
Totevision
Zenith
DVD player
Aiwa
Apex
BOSE
Broksonic
Clarion
078
059, 062
065
065
078
065
079
074
057
009, 010, 065
065
DVD/VCR Combo
Go Video
JVC
RCA
Samsung
Sanyo
Zenith
DVD=087,
VCR=081
DVD=088,
VCR=082
DVD=089,
VCR=083
DVD=090,
VCR=084
DVD=091,
VCR=085
DVD=092,
VCR=086
006, 015
016, 017
097
018
019
020, 040, 044, 046,
050, 053
018, 041, 051
057
027
008, 009, 013
010, 011, 012, 022,
023, 031, 049
033
033
019
048
027
017, 057
029
060
058
036, 052
015, 042
008, 009, 013
022, 023, 030
008, 009, 013, 016
030
059
014, 055
057
025, 026, 037, 054
024
000, 001, 002, 003,
004, 005, 006, 007,
020, 031, 056
021, 028, 030, 032,
035, 039, 043, 045,
047, 058
027
Classic
Daewoo
Denon
Emerson
Fisher
Funai
GE
Go Video
GPX
Hitachi
JVC
Kenwood
Konka
Magnavox
Memorex
Mintek
NAD
Nakamichi
Norcent
Onkyo
Oritron
Panasonic
Philips
Pioneer
Proscan
Qwestar
RCA
Sampo
Samsung
Sansui
Sanyo
Sharp
Sherwood
Sony
Sylvania
Teac
Technics
Techwood
Toshiba
Yamaha
Zenith
Portable DVD player
Aiwa
Audiovox
Panasonic
RCA
093
094, 095
024, 096, 099
098
VCR
Admiral
Aiko
Aiwa
Akai
Audiovox
Bell & Howell
Broksonic
Calix
Carver
CCE
Citizen
Colortyme
Craig
049
019
018
003, 004, 037, 038,
039, 058, 069
010
007, 068
008, 017
010
026
019
009, 010, 011, 012,
013, 014, 015, 019,
057, 073
005
009, 010, 016, 061,
065, 079
020
021
022, 023, 024, 025
026, 027
028
027
001, 029, 030
087
031
005, 032, 033, 034,
035
003, 007, 036, 042,
088
037
008, 009
004, 038
039
040
026
041
043
044
058
010, 045, 046, 047,
048, 049, 050
004, 051
052, 053, 054, 055
001, 056
057, 058
001, 002, 059, 089
060
061, 062, 086, 090
073
063, 091
064, 067
074
011, 012, 065, 066,
068, 069, 070
027
071
072
075
000, 013, 076, 077,
078
079, 080, 081
014, 082, 092
HM66 (E/F) Web 213:276
HM66_EN.book Page 13 Thursday, February 23, 2006 2:49 PM
Chapter 2: Using the remote control
Jensen
JVC
Kenwood
Kodak
LG
Lloyds
Logik
LXI
Magnasonic
Magnavox
Marantz
Memorex
Curtis Mathes
Daewoo
Daytron
Denon
Dimensia
Electrohome
Emerson
Fisher
Fuji
Funai
Garrard
GE
Go Video
Goldstar
Gradiente
Harman Kardon
Hitachi
JBL
JC Penney
MGA
MGN
Minolta
Mitsubishi
Montgomery Ward
Motorola
MTC
Multitech
NEC
Nikko
Noblex
Optimus
Optonica
Orion
061, 063, 065
024, 025, 037
005, 006, 007, 014,
037, 043, 062, 063,
068, 082
005, 006, 007, 012,
014, 037, 043, 053,
068, 071
010
010
053, 073, 079
061
010
061, 065, 078
026, 027, 034, 044,
057, 061, 072
005, 006, 007, 012,
014, 026, 053, 067
007, 009, 010, 016,
018, 034, 049, 063,
065, 066, 068, 075,
079
020, 028, 039
056
024, 025, 035, 063
020, 024, 025, 028,
039, 043, 065
049
049
009, 046, 061
009, 012, 018
005, 006, 007, 012,
014, 037, 043, 053,
054, 067, 070
010
009
010, 049, 065
031
054, 057, 062, 065,
068, 072
001, 005, 009, 012,
014, 040, 048, 053,
056, 057
011, 013, 015, 017,
018, 019, 057, 078
078
063
001, 048
010, 020, 065
003, 008, 010, 011,
017, 018, 020, 028,
039, 054, 057, 062,
065, 068, 072
007, 016, 021, 022,
023, 057, 064, 068,
070, 071, 079
004, 041
018, 073
018
001, 002, 009, 040,
042, 048, 056
056, 059, 061, 081
005, 010, 014, 054,
056, 065, 067
018, 065
005
024, 025, 035, 037,
042, 063, 070, 080
076
005, 006, 007, 008,
009, 010, 023, 024,
025, 026, 035, 056,
Panasonic
Pentax
Pentex Research
Philco
Philips
Pioneer
Portland
Proscan
Proton
Quasar
Radio Shack
Radio Shack/Realistic
Radix
RCA
Realistic
Ricoh
Runco
Samsung
Sansui
Sanyo
Scott
Sears
Sharp
Shintom
Signature
Signature 2000
Singer
Sony
STS
Sylvania
Symphonic
Tandy
Tashiko
Tatung
Teac
Technics
Teknika
Toshiba
Totevision
Unitec
Unitech
Vector Research
Video Concepts
007, 009, 016, 054,
064, 068, 071, 075,
079, 085
008, 011, 017, 028,
030, 057, 065, 072
007, 010, 016, 021,
022, 023, 024, 025,
035, 053, 057, 063,
064, 065, 068, 071,
075, 079
013, 020, 031, 049,
051, 060, 066
004, 025, 032, 061
049
075
047, 061
004, 032, 033, 041,
052, 058, 070, 074,
076, 077, 080
035
018, 026, 027, 028,
044, 072
018, 051, 053, 073,
079
007
010
037
018, 029, 037
036
010, 018, 065
000, 011, 021, 023,
024, 028, 030, 039,
057, 074, 078, 079
009, 010, 065
073
009
005, 006, 011, 012,
053
005, 006, 011, 012,
039, 053
036, 045, 046, 057,
061, 072, 079
012, 024, 025, 035,
042, 053, 063
014
026, 027, 063
026, 031, 044, 057
006, 024, 043, 055
012, 013, 015
001, 002, 048
061
045
010, 031, 065
007, 009, 010, 016,
018, 020, 021, 022,
031, 049
010
001, 002, 003, 009,
024, 025, 029, 035,
040, 042, 045, 048,
055, 056, 063, 071,
083
007, 009, 010, 011,
016, 018, 020, 021,
022, 031, 049, 051,
056, 060, 065, 075,
079
047
034
009, 011, 038, 056,
073, 084
006, 037, 043, 061
Wards
White Westinghouse
XR-1000
Yamaha
Zenith
HTIB
Lasonic
Panasonic
Venturer
009, 010, 011, 016,
018, 020, 024, 025,
031, 035, 049, 051,
056, 057, 060, 065,
066, 079
073
018
005, 006, 007, 014,
037, 053
004, 032, 034, 041,
047, 069, 086
083
084
085
13
HM66 (E/F) Web 213:276
HM66_EN.book Page 14 Thursday, February 23, 2006 2:49 PM
Chapter 3: Menu layout and navigation
Main menu layout
The illustrations below and on the next page provide a quick overview of your TV’s menu system.
To open the main menus (illustrated below), press Y on the remote control or TV control panel.
Icon
Applications
Video
Audio
Preferences
Locks
Setup
Item
Channel Browser
Digital CC/Audio Selector
CableCARD™
Picture Settings
Advanced Picture Settings
Theater Settings
Audio Settings
Advanced Audio Settings
Audio Setup
Favorite Channels
Closed Caption Mode
Closed Caption Advanced
Input Labeling
Menu Language
Channel Browser Setup
Enable Rating Blocking
Edit Rating Limits
Channels Block
Input Lock
Front Panel Lock
New PIN Code
Installation
Sleep Timer
ColorStream HD1 Audio
HDMI 1 Audio
ColorStream HD2 Audio
HDMI 2 Audio
Quick Restart
Option
S [Launches the Channel Browser™]
S [Launches the ATSC Digital CC Selector] (This option is not available, if you are not on a digital channel).
S Dynamic list of items provided by Cable company.
(This option is not available if a CableCARD™ is not inserted.)
S [Picture Settings edit window]
S [Advanced Picture Settings edit window]
S [Theater Settings edit window]
S [Audio Settings window]
S [Advanced Audio Settings window]
S [Audio Setup window]
S [Favorite Channels edit window]
S Off/CC1/CC2/CC3/CC4/T1/T2/T3/T4
S [Closed Caption Advanced window]
S [Input Labeling edit window]
S English / Français / Español
S [Channel Browser Setup window]
S Off/On
S [Edit Rating Limits edit window]
S [Channels Block edit window]
S Off/Video/Video+
S Off/On
S [New PIN Code entry window]
S [Opens the Installation menu (- page 15)]
S [Sleep Timer edit window]
S No/Yes
S Auto / Digital / Analog
S No/Yes
S Auto / Digital / Analog
S Off/On
14
HM66 (E/F) Web 213:276
HM66_EN.book Page 15 Thursday, February 23, 2006 2:49 PM
Chapter 3: Menu layout and navigation
Setup/Installation menu layout
To open the Installation menu (illustrated below), press Y on the remote control or TV control panel, open the Setup menu, select Installation, and press T.
Icon
Press Y.
Open the
Setup menu, and then open the
Installation sub-menu.
Terrestrial
Item
Input Configuration
Channel Program
Channel Add/Delete
Signal Meter
Option
S [Input Configuration window]
S ANT1 S [Scans for new channels on desired
Antenna]
S ANT2 S [Scans for new channels on desired
Antenna]
S [Channel Add / Delete Window]
S [Signal Meter Window]
System Status
System Information
S [Opens the System Information window]
Navigating the menu system
You can use the buttons on the remote control or TV control panel to access and navigate your TV’s on-screen menu system.
•
•
•
•
•
Press Y to open the menu system.
When a menu is open, use the up/down/left/right arrow buttons (BbC c) on the remote control or TV control panel to move in the corresponding direction in the menu.
Press T to save your menu settings or select a highlighted item. (A highlighted menu item appears in a different color in the menu.)
All menus close automatically if you do not make a selection within 60 seconds, except the signal meter menu, which closes automatically after about 5 minutes.
To close a menu instantly, press O.
Note: The menu background may sometimes appear black, depending on the signal the TV is receiving.
This is not a sign of malfunction.
Applications
Channel Browser
Digital CC/Audio Selector
CableCARD
Navigate ENTER Select CH RTN Back EXIT Exit
15
HM66 (E/F) Web 213:276
HM66_EN.book Page 16 Thursday, February 23, 2006 2:49 PM
Chapter 4: Setting up your TV
Selecting the menu language
You can choose from three different languages (English,
French and Spanish) for the on-screen display of menus and messages.
To select the menu language:
1
Press Y and open the Preferences menu.
2
Highlight Menu Language and press c.
3
Press B or b to select your preferred menu language and press T.
Configuring the antenna input sources for the ANT 1 and ANT 2 terminals
To configure the ANT 1 and ANT 2 input sources:
1
Press Y and open the Setup menu.
2
Highlight Installation and press T. (A new set of
Installation menu icons will appear on-screen, as shown in step 3 below.)
Preferences
Favorite Channels
Closed Caption Mode
Closed Caption Advanced
Input Labeling
Off
Menu Language English
Channel Browser Setup
English
Français
Español
Navigate ENTER Select CH RTN Back EXIT Exit
4
Press O to close the Preferences menu.
Setup
Installation
Sleep Timer
ColorStream HD1 Audio
HDMI 1 Audio
ColorStream HD2 Audio
HDMI 2 Audio
Quick Restart
No
Auto
No
Auto
On
Navigate ENTER Select CH RTN Back EXIT Exit
3
Open the Terrestrial menu, highlight Input
Configuration, and press T.
Terrestrial
Input Configuration
Channel Program
Channel Add/Delete
Signal Meter
Navigate
ENTER Select CH RTN
Back
EXIT
Exit
4
Press B or b to highlight ANT 1, and press C or c to select the input source (Cable or Antenna) for the
ANT 1 input on the TV.
5
Press b to highlight Antenna 2 in and then C or c to select the input source (Cable or Antenna) for the ANT 2 input on the TV, if applicable. If you have not connected anything to the ANT 2 input, skip this step.
Input Configuration
Antenna 1 In
Antenna 2 In
Cancel
Cable
Antenna
Done
6
To save your new settings, highlight Done and press T.
To revert to your original settings, highlight Cancel and press T.
16
HM66 (E/F) Web 213:276
HM66_EN.book Page 17 Thursday, February 23, 2006 2:49 PM
Chapter 4: Setting up your TV
Programming channels into the
TV’s channel memory
When you press < or , on the remote control or TV control panel, your TV will stop only on the channels you program into the TV's channel memory.
Follow the steps below to program channels into the TV’s channel memory.
Programming channels automatically
Your TV can automatically detect all active channels in your area and store them in its memory. After the channels are programmed automatically, you can manually add or erase individual channels.
Notes:
• You must configure the antenna input sources before
programming channels (
- page 16).
• If the input signal type is set to Cable for an antenna input,
the automatic channel programming process erases channels that were previously programmed into the TV’s memory.
• If the input signal type is set to Antenna, the automatic
channel programming process does NOT erase channels that were previously programmed into the TV’s memory, but adds newly found channels to the existing set of programmed channels. To remove a channel from the memory, you must manually delete it.
• To tune the TV to a channel not programmed in the channel
memory, you must use the Channel Number buttons on the remote control.
• Programming channels for an antenna input configured for
Cable will take substantially longer than for an antenna input configured for Antenna. This is normal; however, once channel programming is completed, you should not have to repeat the programming process again unless your Cable
TV service lineup changes significantly.
• If you have a CableCARD™ inserted, channel programming
for ANT 1 is disabled because the CableCARD™ automatically loads the Cable channel list into the TV’s channel memory. See Installation Guide for details on
CableCARD™.
To program channels automatically:
1
Make sure you have configured the antenna input sources
(
- page 16).
2
Press Y and open the Setup menu.
3
Highlight Installation and press T. (A new set of
Installation menu icons will appear on-screen, as shown in step 4.)
Setup
Installation
Sleep Timer
ColorStream HD1 Audio
HDMI 1 Audio
ColorStream HD2 Audio
HDMI 2 Audio
Quick Restart
No
Auto
No
Auto
On
Navigate ENTER Select CH RTN Back EXIT Exit
4
Open the Terrestrial menu, highlight Channel
Program, and press T.
Terrestrial
Input Configuration
Channel Program
Channel Add/Delete
Signal Meter
Navigate ENTER Select CH RTN Back EXIT Exit
5
Highlight ANT 1 or ANT 2, depending on which antenna input you want to program channels for, and then press T to start automatic channel programming.
ANT 1 Antenna
Scanning channels, please wait ...
52%
Abort
The TV will automatically cycle through all the channels for the antenna input you selected, and store all active channels in the channel memory. While the TV is cycling through the channels, the message “Scanning channels, please wait” appears (as shown above).
6
To cancel channel programming, either press O or highlight Abort in the on-screen display and press T.
When channel programming is done, press < or , to view the programmed channels.
Manually adding and deleting channels in the channel memory
After automatically programming channels into the channel memory, you can manually add or delete individual channels.
To add or delete channels in the channel memory:
1
Press Y and open the Setup menu.
2
Highlight Installation and press T. (A new set of
Installation menu icons will appear on-screen, as shown in step 3.)
(continued)
17
HM66 (E/F) Web 213:276
HM66_EN.book Page 18 Thursday, February 23, 2006 2:49 PM
Chapter 4: Setting up your TV
3
Open the Terrestrial menu, highlight Channel Add/
Delete, and then press T.
Terrestrial
Input Configuration
Channel Program
Channel Add/Delete
Signal Meter
Navigate ENTER Select CH RTN Back EXIT Exit
4
The illustration below left shows channels programmed for the ANT 1 antenna input. To view the list of channels programmed for the ANT 2 antenna input, press Bb to highlight ANT 2 and press T.
Channel Add/Delete
6
7
4
5
2
2 - 1
2 - 2
3
7 - 1
8
Analog
Digital
Digital
Analog
Analog
Analog
Analog
Analog
Digital
Analog
ANT 1
ANT 2
Reset
Cancel
Done
Channel Add/Delete
9
10
7
8
5
6
3
4
1
2
Analog
Analog
Analog
Analog
Analog
Analog
Analog
Analog
Analog
Analog
ANT 1
ANT 2
Reset
Cancel
Done
To add a channel to the channel memory:
Highlight the unchecked box next to the channel number you want to add, and then press T to check the box.
To manually add digital subchannels on a physical channel:
Use the Channel Numbers and the Dash (=) on the remote control to enter the channel number (for example, 56–1).
If the channel is found, the number will be added to the list and the box will be checked.
If the channel is not found, a message will appear.
To remove a channel from the channel memory:
Highlight the checked box next to the channel number you want to remove, and then press T to uncheck the box.
To save your new settings:
Highlight Done and press T.
To revert to your original settings:
Highlight Cancel and press T before saving.
To remove all channels from the channel memory:
Highlight Reset and press T, and then highlight Done and press T.
Notes:
• This action applies to the current antenna input only. To
delete/add channels on the other input, highlight the input you want (ANT1, or ANT 2) and press
T.
• This action cannot be cancelled unless you highlight Cancel
and press
T before saving your changes.
Channel Add/Delete
4
5
6
2
2 - 1
2 - 2
3
7
7 - 1
8
Analog
Digital
Digital
Analog
Analog
Digital
Analog
Analog
Digital
Analog
ANT 1
ANT 2
Reset
Cancel
Done
Programming your favorite channels
You can program up to 18 channels as favorite channels into two Favorite Channel lists (nine channels from the ANT 1 input, and nine from the ANT 2 input). You can then scan through your favorite channels only, skipping other channels you do not normally watch.
To add and delete channels in the Favorite Channels lists:
1
Press Y and open the Preferences menu.
2
Highlight Favorite Channels and press T.
3
Use Bb to select either ANT 1, or ANT 2, and press T.
4
Highlight Edit and press T.
Preferences
Favorite Channels
Closed Caption Mode
Closed Caption Advanced
Input Labeling
Off
Menu Language English
Channel Browser Setup
Favorite Channels
Empty Empty
Empty
Empty
Empty
Empty
Empty
Empty
Empty
ANT 1
ANT 1
ANT 2
Edit
Done
Navigate ENTER Select CH RTN Back EXIT Exit
To add a channel to the selected Favorite Channel list:
Use Bb to highlight an unchecked box next to a channel you want to set as a favorite, and then press T to check the box.
Note: You must first use Channel Program or Channel Add/
Delete to add channels to the channel memory before setting up favorite channels.
18
HM66 (E/F) Web 213:276
HM66_EN.book Page 19 Thursday, February 23, 2006 2:49 PM
Chapter 4: Setting up your TV
To delete the channel from the selected Favorite
Channel list:
Highlight a checked box and press T to uncheck it.
Edit Favorite Channels ANT 1
2
3
4
Only 9 favorite channels are allowed, please deselect other channels first.
OK
9
10
11
Reset
Cancel
Done
Note: If you try to add more than nine favorite channels per input, an error message will appear. You will need to delete
(uncheck) a channel before you can add another.
When done, highlight Done and press T.
•
•
To program favorite channels for another input:
Either... Highlight ANT 1, or ANT 2, which will change the favorite channel settings in the selected input. (This will not change the TV’s current input.)
Or... Press + to select ANT 1, or ANT 2 and then repeat steps 1–4, on page 18.
Favorite Channels ANT 2
6 Empty Empty
ANT 1
ANT 2
Empty Empty Empty
Empty Empty Empty
Edit
Done
To clear your favorite channel lists:
1
Press Y and open the Preferences menu.
2
Highlight Favorite Channels and press T.
3
Highlight Edit and press T.
4
Highlight Reset and press T.
5
Highlight Done and press T.
Edit Favorite Channels
2
2 - 1
2 - 2
4 - 1
5
17 - 1
17 - 2
28 - 1
28 - 2
28 - 3
ANT 2
Reset
Cancel
Done
To tune your favorite channels for the current ANT input:
Press M / m.
To tune your favorite channels using the favorite channel list:
1
Press = to display the favorite channel list.
2
Press the corresponding number button (1-9) to select your desired channel.
5
6
3
4
1
2
7
8
9
CH 4-1
CH 4-2
CH 9
CH 10
CH 12
CH 17
CH 19
- - -
- - -
Note: To tune your favorite channels for another input, press
+ to select the other input.
19
HM66 (E/F) Web 213:276
HM66_EN.book Page 20 Thursday, February 23, 2006 2:49 PM
Chapter 4: Setting up your TV
Setting the ColorStream HD audio mode
To set the ColorStream HD audio mode:
1
Press Y and open the Setup menu.
2
Highlight ColorStream HD1(or 2) Audio and press c.
3
Press B or b to select Yes or No and press T to display the information.
Setup
Installation
Sleep Timer
ColorStream HD1 Audio
HDMI 1 Audio
ColorStream HD2 Audio
HDMI 2 Audio
Quick Restart
No
Auto
No
Auto
On
No
Yes
Navigate ENTER Select CH RTN Back EXIT Exit
Note: The analog audio terminals for the ColorStream HD and
HDMI inputs are used in common. When the ColorStream HD
1 (or 2) audio mode is set to Yes, the HDMI 1 (or 2) audio mode is set to Digital and will be greyed out. When the ColorStream
HD 1 (or 2) audio mode is set to No, the HDMI 1 (or 2) Audio changes to Auto.
Viewing the CableCARD™ menu
A CableCARD™ enables you to view encrypted digital channels. See “Connecting a digital CableCARD™”
(- Installation Guide) for connection and subscription information.
Note: Connecting your TV directly to the Audio/Video output of your Set-Top-Box will assure a more vivid picture and enhance your viewing enjoyment.
After the CableCARD™ is inserted, a CableCARD™ option appears in the Applications menu, with informational screens provided by your digital CableCARD™ service (see illustrations below).
CableCard Connected -- Acquiring channel information.
CableCard services will only operate with cable signal connected to Antenna 1.
To view the CableCARD™ menu:
1
Press Y and open the Applications menu.
2
Highlight CableCARD™ and press c.
3
Press B or b to select one of the side menu items and press T to display the information.
Setting the HDMI™ audio mode
To set the HDMI audio mode:
1
Press Y and open the Setup menu.
2
Highlight HDMI 1 (or 2) Audio and press c.
3
Press b or B to select the HDMI audio mode (Auto,
Digital, or Analog) and press T. (Auto is the recommended mode.) See “Connecting an HDMI or DVI device to the HDMI input” (- Installation Guide).
Applications
Channel Browser
Digital CC/Audio Selector
CableCARD
IP Service
Conditional Access
CableCARD(tm) Status
Network Setup
CableCARD(tm) Pairing
Navigate ENTER Select CH RTN Back EXIT Exit
Note: The CableCARD™ menu is for informational purposes only and has no user-adjustable options.
Setup
Installation
Sleep Timer
ColorStream HD1 Audio
HDMI 1 Audio
ColorStream HD2 Audio
HDMI 2 Audio
Quick Restart
No
Auto
No
Auto
On
Auto
Digital
Analog
Navigate
ENTER
Select
CH RTN
Back
EXIT
Exit
Note: The ColorStream HD1/HD2 Audio settings influence the
HDMI Audio settings. If ColorStream HD1 (or 2) Audio is set to
No, the HDMI 1 (or 2) Audio setting changes to Auto. If either
ColorStream HD1 (or 2) Audio is set to Yes, the HDMI 1 (or 2)
Audio setting is set to Digital and will be greyed out.
Setting the Quick Restart™ feature
With the Quick Restart™ feature set to On, the TV will stay in
Standby mode for several minutes after the TV is turned off
(see Note on page 21).
If the TV is turned on from Standby mode, the full picture appears immediately.
20
HM66 (E/F) Web 213:276
HM66_EN.book Page 21 Thursday, February 23, 2006 2:49 PM
Chapter 4: Setting up your TV
To set the Quick Restart™ feature:
1
Press Y and open the Setup menu.
2
Highlight Quick Restart and press c.
3
Press b or B to select either On or Off and Press T.
Setup
Installation
Sleep Timer
ColorStream HD1 Audio
HDMI 1 Audio
ColorStream HD2 Audio
HDMI 2 Audio
Quick Restart
No
Auto
No
Auto
On
Off
On
Navigate ENTER Select CH RTN Back EXIT Exit
Note: If Quick Restart is set to Off and you turn off the TV, it can take several seconds for the picture to appear when you turn on the TV again. See “important notice about hot lamp restart,” below.
If Quick Restart is set to On and you turn off the TV, the following will occur for a few minutes:
• The screen (lamp) lights dimly; and
• The fans continue to run.
This is a function of the Quick Restart Shutdown mode and is not a TV malfunction. If you do not prefer this, set the Quick
Restart feature to Off.
When the Quick Restart feature is set to Off, if you repeatedly turn the TV on and off in a short period of time, the useful service life of the lamp may be shorter than the average useful service life (
- page 47).
IMPORTANT NOTICE ABOUT “HOT LAMP RESTART”
When the TV has been powered on long enough for the lamp unit to get hot, it may take several minutes for the picture to appear on-screen in the following situations:
•
When the Quick Restart™ feature is set to
Off
and
• you turn the TV off and then on again within a few minutes; or
If the TV is on when a short-term power failure, power surge, or other similar power failure occurs, such that the TV loses and regains power within a few minutes.
This is a property of DLP™ TV lamp technology and is NOT a sign of malfunction.
If this occurs, the yellow LED on the TV front panel will blink (and the blue LED will be lit solid) until the TV is finished restarting the lamp and the normal picture appears. If both LEDs are blinking, you will need to turn the TV off and then on again to restart the lamp.
Viewing the digital signal meter
You can view the digital signal meter in the ANT 1 and ANT
2 digital TV input sources only.
To view the digital signal meter:
1
Press Y and open the Setup menu.
2
Highlight Installation and press T.
3
A new set of Installation menu icons will appear onscreen, as shown below.
Open the Terrestrial menu, highlight Signal Meter, and press T.
Terrestrial
Input Configuration
Channel Program
Channel Add/Delete
Signal Meter
Navigate ENTER Select CH RTN Back EXIT Exit
4
Press BbC c to select the antenna input and digital channel whose signal you want to check.
Note: The physical digital channel number listed in the
Signal Meter screen may not correspond to a virtual TV channel number. Contact your local broadcasters to obtain the RF channel numbers for your local digital stations.
Signal Meter
Signal Locked
Antenna
Physical Digital Channel
Virtual Digital Channel
Done
0
Peak 0
1
4
4/1
To close the screen and return to the Terrestrial menu:
Highlight Done and press T.
To return to normal viewing:
Press O.
21
HM66 (E/F) Web 213:276
HM66_EN.book Page 22 Thursday, February 23, 2006 2:49 PM
Chapter 4: Setting up your TV
Viewing the system status
To view the system status:
1
Press Y and open the Setup menu.
2
Highlight Installation and press T. A new set of
Installation menu icons will appear on-screen, as shown below right.
To cancel the reset:
Highlight No and press T.
Note: If you have previously set the TV to High Bright mode, and have restored Factory Defaults, the TV will default to Low
Power mode. To set the TV back to High Bright mode, see page 42.
Setup
Installation
Sleep Timer
ColorStream HD1 Audio
HDMI 1 Audio
ColorStream HD2 Audio
HDMI 2 Audio
Quick Restart
No
Auto
No
Auto
On
System Status
System Infomation
Navigate ENTER Select CH RTN Back EXIT Exit Navigate ENTER Select CH RTN Back EXIT Exit
3
Open the System Status menu, highlight System
Information, and press T.
4
Press C c to scroll through the menu bar to check the
Product Information and Software Version.
System Information
System Information
Product Information
Brand:
Model:
Toshiba
50HM66
Software Version
2.2.26.0
Jan 24 2006 - 11:04:47
FW: 17
Done
Done
To close the screen and return to the Installation menu:
Highlight Done and press T.
To return to normal viewing:
Press O.
Restore Factory Defaults
To restore all settings and channels to their factory default values:
1
Follow steps 1–3 above.
2
Press C c to scroll through the menu bar to select
Factory Defaults.
3
Enter your PIN code (or 0000 if no PIN code has been set).
4
Highlight Yes and press T. The TV will turn off automatically after a few seconds. After the TV turns off, unplug the TV power cord and then plug it in again to complete the restore process.
System Information
Press YES to confirm. After the TV turns off, unplug it and plug it back in to complete the reset.
No
Yes
22
HM66 (E/F) Web 213:276
HM66_EN.book Page 23 Thursday, February 23, 2006 2:49 PM
Chapter 5: Using the TV’s basic features
Selecting the video input source to view
To select the video input source to view:
1
Press + on the remote control or INPUT on the TV control panel.
2
Press 0–7 to select the input source you want to view, which will depend on the input terminals you used to connect your devices (- Installation Guide).
The current signal source displays in the top right corner of the Input Selection screen.
Input Selection
0
1
2
Video 1
5
6
3
4
Video 2
ColorStream HD1
ColorStream HD2
HDMI 1
7
HDMI 2
ANT 2
0 7 / INPUT to Select
ANT 1
Notes:
• When the Input Selection screen is open, you also can use
Bb on the remote control (or the CHANNEL U u buttons on
the control panel) to change the input.
• You can repeatedly press
+ on the remote control or the
INPUT button on the TV control panel to change the input.
• You can label the video input sources according to the
specific devices you have connected to the TV
(
- “Labeling the video input sources” at right).
• The source can be “hidden” (
- “Labeling the video input
sources” at right).
Labeling the video input sources
You can label each video input source according to the type of device you connected to each source, from the following preset list of labels:
•
•
“– –”(default label)
Cable
•
•
•
•
DTV
Satellite/DSS
VCR
Laser Disk
•
•
•
•
•
•
DVD
Audio Receiver
Compact Disc
Video Recorder
Game Console
Hide (to hide an unused input in the Input Selection screen)
Note: If you select ANT 2 in the Input selection screen, you can select either “– –” or “Hide”.
To label the video input sources:
1
Press Y and open the Preferences menu.
2
Highlight Input Labeling and press T.
3
Press B or b to highlight the video source you want to label.
Preferences
Favorite Channels
Closed Caption Mode
Closed Caption Advanced
Off
Input Labeling
Menu Language
Channel Browser Setup
English
Navigate ENTER Select CH RTN Back EXIT Exit
Input Labeling
Video 1
Video 2
ColorStream HD 1
ColorStream HD 2
HDMI 1
HDMI 2
ANT 2
Reset
DVD
Cable
Video Recorder
Hide
DTV
Satellite/DSS
- -
Done
4
Press C or c to select the desired label for that input source. If a particular input is not used, you can select
Hide as the label, which will cause that input to be
“grayed out” in the input list and skipped over when you press + on the remote control.
5
To save the new input labels, highlight Done and press
T. To revert to the factory default labels, highlight
Reset and press T.
(continued)
23
HM66 (E/F) Web 213:276
HM66_EN.book Page 24 Thursday, February 23, 2006 2:49 PM
Chapter 5: Using the TV’s basic features
Input labeling example:
The screen below left shows the default Input Selection screen (with none of the inputs labeled). The screen below right is an example of how you could label the inputs if you had connected a DVD player to VIDEO 1, Cable TV to VIDEO 2, a video recorder to ColorStream HD1, a DTV set-top box to
HDMI 1, and a satellite/DSS set-top box to HDMI 2. Also note that the ColorStream HD2 input is labeled “Hidden,” which means that the input will be skipped over when + is pressed.
Input Selection
4
5
6
7
2
3
0
1
Video 1
Video 2
ColorStream HD1
ColorStream HD2
HDMI 1
HDMI 2
ANT 2
0
-
7
/ INPUT to Select
ANT 1
Input Selection screen with no inputs labeled
Input Selection
6
7
4
5
0
1
2
3
DVD
Cable
Video Recorder
ColorSteram HD2 (Hidden)
DTV
Satellite/DSS
ANT 2
ANT 1
0 7 / INPUT to Select
Input Selection screen with all inputs labeled except input 4, which has been hidden.
To clear the input labels:
1
Press Y and open the Preferences menu.
2
Highlight Input Labeling and press T.
3
Highlight Reset and press T.
Tuning channels
Using the Channel Browser™
The Channel Browser™ stores the most recently viewed channels or inputs in a history list. In addition, it provides a list of all the available channels on the ANT1 input (up to 2000), the ANT2 input (up to 2000) and a list of all the inputs on the
TV. This feature allows you to:
•
Keep a history of the last 32 channels or inputs viewed.
•
•
•
•
Quickly surf and tune your recently viewed channels/inputs from the Channel Browser™ banner (illustrated on the next page).
Surf via Browse mode (to immediately tune channels as you highlight them in the Channel Browser™ banner) or Select mode (to surf over channels in the browser banner before you select one to tune).
Quickly change inputs from the Inputs List.
Set a “HOME” source for an ANT1 or ANT2 channel or TV input.
To set the Channel Browser™:
1
Press Y and open the Preferences menu.
2
Highlight Channel Browser Setup and press T.
3
Press B to highlight Navigation, and then press C or c to select either Browse Mode or Select Mode.
Channel Browser Setup
Navigation
History List
ANT1 List
ANT2 List
Inputs List
Reset
Select Mode
Power Off Clear(On)
On
On
On
Done
4
Press b to highlight History List field, then press C or c to select the setting you prefer either Power Off Clear
(On), On or Off.
Note: When History List is set to On, the channels and inputs stored in the list will be saved through power on and off. When History List is set to Power Off Clear (On), the channels and inputs stored in the list will be cleared with every power on/off cycle of the TV.
5
Press b to highlight ANT1 List field, then press C or c to select On or Off.
6
Press b to highlight ANT2 List field, then press C or c to select On or Off.
7
Press b to highlight Inputs List field, then press C or c to select On or Off.
8
To save your entries, highlight Done and press T.
To return to factory defaults, highlight Reset and press
T.
24
HM66 (E/F) Web 213:276
HM66_EN.book Page 25 Thursday, February 23, 2006 2:49 PM
Chapter 5: Using the TV’s basic features
•
•
•
To open the Channel Browser™ banner:
Press 3 C, # c, or i on the remote control.
Press 3 C to surf back from the most recently viewed channel through the last 32 channels or inputs in the History list, ANT 1 channels list, ANT 2 channels list or the inputs list.
Press # c to surf forward from the previous item in the channel history, ANT 1, ANT 2, or inputs up to the most recently viewed item or end of list.
Elements of the Channel Browser™ banner
1 2 3 4
1
4
History
1
87-1
ANT 1
1
6
BLOCKED
CABLE
ClrStrmHD2
__
4
1
4-1
AAA 480i
Hold HOME key
3 sec to program
ANT 1(4)
5
1
Input type
6 7 8 9 10 11
2
Highlighted item (channel or input)
3
Channels stored in the channel history
4
Home instructions (this will be replaced once there are at least 6 items in the History, ANT 1 or Inputs lists)
5
Current list (History, ANT 1, ANT 2 or Inputs)
6
Current input
7
Current antenna type (cable or TV)
8
Active channel number
9
Channel call letters (if available)
10 Resolution
11 Home source
To toggle between History, ANT 1, ANT 2 and
Inputs:
After opening the Channel Browser™ banner, press B or b to toggle between History, ANT 1, ANT 2 and Inputs.
Note: The Channel Browser™ banner opens in History List by default. Once another list has been selected, the
Channel Browser™ will open in the last selected list.
To tune to a channel or input in Browse mode:
1
While watching TV, press 3 C or # c to open the
Channel Browser™ banner and surf back to a previous item or surf forward to the next item in the list.
In Browse mode, when you stop on an item in the browser banner, it will be highlighted and the TV will automatically tune to the channel or input.
2
Press O to close the Channel Browser™ banner.
Note: The Channel Browser™ banner will close automatically if you do not make a selection within 30 seconds.
To tune to a channel or input in Select mode:
1
While watching TV, press 3 C or # c to open the
Channel Browser™ banner and surf back to a previous item or surf forward to the next item in the list.
In Select mode, when you stop on an item in the browser banner, it will be highlighted but the TV will not automatically tune to the channel or input.
2
Press T to tune the TV to the highlighted item.
3
Press O to close the Channel Browser™ banner.
Adding and clearing channels and inputs in the channel history
Adding channels and inputs to the channel history:
The Channel Browser™ automatically creates a history of the last 32 channels or inputs that were tuned by adding that channel or input to the right of the list (revisited items are moved to the end of the list).
The Channel Browser™ will store the following channels:
•
All channels that are tuned using the numeric buttons on the remote control.
•
All channels that are tuned to using < or ,, M or m on the remote control and inputs that are tuned to for at least
5 seconds.
Note: The TV will automatically tune to the previously viewed channel or input whenever an item is selected that cannot be tuned for various reasons.
•
•
Clearing channels from the channel history:
Turning off the TV will clear the channel history only if
History List in the Channel Browser Setup is set to
“Power Off Clear (On).”
Reconfiguring the ANT 1 or ANT 2 input will clear the channel history.
•
•
Note: See page16 for details on configuring the antenna input.
Removing the CableCARD™ will clear the channel history.
Once 32 channels or inputs are stored in the history list, the oldest item will be removed from the list when a new channel or input is tuned.
25
HM66 (E/F) Web 213:276
HM66_EN.book Page 26 Thursday, February 23, 2006 2:49 PM
Chapter 5: Using the TV’s basic features
Using the Home feature
To set a channel or input as Home:
1
Tune the TV to the channel or input you would like to set as the Home source.
2
Press and hold i on the remote control for 3 seconds.
When HOME is saved, the Channel Browser™ banner will appear at the bottom of the screen and the HOME icon will flash green.
To tune to HOME:
Press the i button on the remote to tune to your HOME channel or input. The Channel Browser™ banner will display when HOME is tuned unless all lists have been turned to “Off” in the Channel Browser Setup.
Note: If all lists are turned to off, Home may not be set at this time; however, if it is already set, pressing the
i button on the
remote will tune to the Home source, but will not display the
Channel Browser™ .
Tuning your favorite channels
To tune to the channels you programmed as Favorite Channels, see page 18.
Tuning to the next programmed channel
To tune to the next programmed channel:
Press < or , on the remote control or TV control panel.
Note:This feature will not work unless you program channels into the TV’s channel memory (
- page 17).
Tuning to a specific channel (programmed or unprogrammed)
Tuning analog channels:
Press the Channel Number buttons (0–9) on the remote control. For example, to select channel 125, press 1, 2, 5.
Tuning digital channels:
Press the Channel Number buttons (0–9) on the remote control, followed by the dash (=) button and then the subchannel number. For example, to select digital channel 125-1, press 1, 2, 5, –, 1.
Note: If a digital channel is not programmed–either through the automatic channel scan (
- page 17) or the channel add/
delete function (
- page 17)–you will have to tune the RF
channel using the Channel Number and the dash (
=) buttons
on the remote control.
Switching between two channels using
Channel Return
The Channel Return feature allows you to switch between two channels without entering an actual channel number each time.
1
Select the first channel you want to view.
2
Select a second channel using the Channel Number buttons (and the dash (=) button if selecting a digital channel).
3
Press R on the remote control. The previous channel will display. Each time you press R, the TV will switch back and forth between the last two channels that were tuned.
Note:If you press
R from a non-antenna input, the TV
will return to the last-viewed ANT input and channel.
Switching between two channels using
SurfLock™
The SurfLock™ feature temporarily “memorizes” one channel in the R button, so you can return to that channel quickly from any other channel by pressing R. To memorize a channel in the R button:
1
Tune the TV to the channel you want to program into the
R button.
2
Press and hold R for about 2 seconds until the message
“Channel Memorized” appears on the screen. The channel has been programmed into the R button.
3
You can then change channels repeatedly, and when you press R, the memorized channel will be selected.
The TV will return to the memorized channel one time only.
Once you press R and then change channels again, the CH
RTN memory will be cleared and the button will function as
Channel Return, by switching back and forth between the last two channels that were tuned.
26
HM66 (E/F) Web 213:276
HM66_EN.book Page 27 Thursday, February 23, 2006 2:49 PM
Chapter 5: Using the TV’s basic features
Selecting the picture size
You can view many program formats in a variety of picture sizes—Natural, TheaterWide 1, TheaterWide 2,
TheaterWide 3, and Full.
The way the image displays in any of the picture sizes will vary depending on the format of the program you are viewing.
Select the picture size that displays the current program the way that looks best to you.
Your picture size preferences can be saved for each input on your TV.
To select the picture size:
1
Press I on the remote control.
2
While the Picture Size screen is on-screen, press the corresponding number button (0–4) to select the desired picture size.
Picture Size
0
Natural
3
4
1
2
TheaterWide 1
TheaterWide 2
TheaterWide 3
Full
0
-
4
/
PIC SIZE to Select
Notes:
• You also can repeatedly press
I to select the desired
picture size (or press
Bb on the remote control while the
Picture Size screen is open).
• Full may not be available for some program formats (it will
be “grayed out” in the Picture Size screen).
• You also can select the picture size using the menu system.
Select Picture Size in the Theater Settings menu. Select the input for which you want to save your picture settings. To save your settings, highlight Done and press
T.
Theater Settings
Picture Size
Picture Scroll
Cinema Mode
Auto Aspect Ratio
Reset
- -
Natural
Film
On
Done
Using these functions to change the picture size (i.e., changing the height/ width ratio) for any purpose other than your private viewing may be prohibited under the Copyright
Laws of the United States and other countries, and may subject you to civil and criminal liability.
•
Natural picture size
The image is displayed close to its originally formatted proportion. Some program formats will display with sidebars and/or bars at the top and bottom.
Natural picture size example: The way the image displays will vary depending on the format of the program you are currently watching.
Conventional picture on a conventional TV screen
Conventional picture in Natural size on your wide-screen TV
TheaterWide 1 picture size (For 4:3 format program)
•
The center of the picture remains close to its original proportion, but the left and right edges are stretched wider to fill the screen.
TheaterWide 1 picture size example
TheaterWide 2 picture size (for letter box programs)
•
•
The picture is stretched wider to fill the width of the screen, but only slightly stretched taller.
The top and bottom edges of the picture are hidden. To view the hidden areas, see “Scrolling the TheaterWide
®
picture”
(- page 28).
A B C D E F G - - - - - - - - - - - - - - - -
TheaterWide 2 picture size example
(continued)
27
HM66 (E/F) Web 213:276
HM66_EN.book Page 28 Thursday, February 23, 2006 2:49 PM
Chapter 5: Using the TV’s basic features
TheaterWide 3 picture size (for letter box programs with subtitles)
•
•
The picture is stretched wider to fill the width of the screen, but only slightly stretched taller.
The top and bottom edges are hidden. To view the hidden areas (such as subtitles or captions), see “Scrolling the
TheaterWide
®
picture”.
Scrolling the TheaterWide
®
picture
(TheaterWide 2 and 3 only)
You can set separate scroll settings for the TheaterWide 2 and
TheaterWide 3 modes for each input.
To set the scroll settings:
1
Press Y and open the Video menu.
2
Highlight Theater Settings and press T.
A B C D E F G - - - - - - - - - - - - - - - -
A B C D E F G - - - - - - - - - - - - - - - - - - - - - - - - - -
TheaterWide 3 picture size example
Full picture size (for 16:9 [480i, 480p] source programs only)
•
•
If receiving a squeezed 4:3 format program, the picture is stretched wider to fill the width of the screen, but not stretched taller.
None of the picture is hidden.
Video
Picture Settings
Advanced Picture Settings
Theater Settings
Full picture size example
Notes:
• If you select one of the TheaterWide
®
picture sizes, the top and bottom edges of the picture (including subtitles or captions) may be hidden. To view the hidden edges, either scroll the picture (TheaterWide 2 and 3 only) or try viewing the program in Full or Natural picture size.
• When selecting the picture size, the way the image displays
will vary depending on the format of the program you are currently watching.
Navigate
ENTER Select CH RTN
Back
EXIT
Exit
3
In the Picture Size field, select either TheaterWide 2 or TheaterWide 3 (you cannot scroll in any other mode).
4
Press b to highlight the Picture Scroll field.
5
Press C or c to scroll the picture up and down as needed, from –10 to +20.
Theater Settings
Picture Size
Picture Scroll
Cinema Mode
Auto Aspect Ratio
-5
TheaterWide 2
Film
On
Reset Done
6
To save the new settings, highlight Done and press T.
To revert to the factory defaults, highlight Reset and press T.
28
HM66 (E/F) Web 213:276
HM66_EN.book Page 29 Thursday, February 23, 2006 2:49 PM
Chapter 5: Using the TV’s basic features
Using the auto aspect ratio feature
When the auto aspect ratio feature is set to On, the picture size is automatically selected when one of the following input sources is received:
•
A 480i signal from the VIDEO 1, VIDEO 2, ColorStream
HD-1, or ColorStream HD-2 input.
•
A 1080i, 480i, 480p, or 720p signal from the HDMI input.
Aspect ratio of signal source
Automatic aspect size (automatically selected when Auto Aspect is On)
4:3 normal Natural (with sidebars)
4:3 letter box TheaterWide 2
Full 16:9 full
Not defined
(no ID-1 data or HDMI aspect data)
Selecting the picture size (- page 27)
Note: The auto aspect ratio feature is not applicable to antenna or cable input sources.
To turn on the auto aspect ratio feature:
1
Press Y and open the Video menu.
2
Highlight Theater Settings and press T.
3
In the Auto Aspect Ratio field, select On.
Theater Settings
Picture Size
Picture Scroll
Cinema Mode
Auto Aspect Ratio
-1
Natural
Film
On
Reset Done
4
To save the new settings, highlight Done and press T.
To revert to the factory defaults, highlight Reset and press T.
To turn off the auto aspect ratio feature:
Select Off in step 3 above.
Selecting the cinema mode
(480i signals only)
When you view a DVD (480i signal; 3:2 pulldown processed) from a DVD player connected to the VIDEO 1, VIDEO 2,
ColorStream HD-1/HD-2 (component video), or HDMI inputs on the TV, smoother motion can be obtained by setting the Cinema Mode to Film.
To set the Cinema Mode to Film:
1
Press Y and open the Video menu.
2
Highlight Theater Settings and press T.
3
In the Cinema Mode field, select Film.
Theater Settings
Picture Size
Picture Scroll
Cinema Mode
Auto Aspect Ratio
-1
Natural
Film
On
Reset Done
4
To save the new settings, highlight Done and press T.
To revert to the factory defaults, highlight Reset and press T.
To set the Cinema Mode to Video:
Select Video in step 3 above.
29
HM66 (E/F) Web 213:276
HM66_EN.book Page 30 Thursday, February 23, 2006 2:49 PM
Chapter 5: Using the TV’s basic features
Adjusting the picture
Selecting the picture mode
You can select your desired picture settings from four different modes, as described below.
Mode
Sports
Standard
Movie
Preference
Picture Quality
Bright and dynamic picture (factory setting)
Standard picture settings (factory setting)
Lower contrast for darkened room (factory setting)
Your personal preferences
To select the picture mode using the menu system:
1
Press Y and open the Video menu.
2
Highlight Picture Settings and press T.
3
In the Mode field, select the picture mode you prefer.
ANT 1 Picture Settings
Mode
Contrast
Brightness
Color
Tint
Sharpness
Reset
100
50
50
0
50
Sports
Done
Picture Settings
Mode
Mode: Standard
Standard
4
To save the new settings, highlight Done and press T.
To revert to the factory defaults, highlight Reset and press T.
Notes:
• The picture mode you select affects the current input
only (ANT 1 in the example above). You can select a different picture mode for each input.
• If you select one of the factory-set picture modes
(Sports, Standard, or Movie) and then change a picture quality setting (for example, increase the contrast or change the color temperature), the picture mode automatically changes to Preference in the
Picture Settings menu.
• If you have previously set the TV to High Bright mode,
and have chosen Reset in item 4 above, the TV will default to Low Power mode. To set the TV back to High
Bright mode, see page 42.
Adjusting the picture quality
You can adjust the picture quality (contrast, brightness, color, tint, and sharpness) to your personal preferences.
Selection
contrast brightness color tint sharpness
C
lower darker paler reddish softer
Pressing
c
higher lighter deeper greenish sharper
To adjust the picture quality:
1
Press Y and open the Video menu.
2
Highlight Picture Settings and press T.
3
Press B or b to select the picture quality you want to adjust (Contrast, Brightness, Color, Tint, or
Sharpness), and then press C and c to adjust the setting, as described in the table above.
ANT 1 Picture Settings
Mode
Contrast
Brightness
Color
Tint
Sharpness
Reset
100
50
50
0
50
Sports
Done
Mode: Preference Picture Settings
Contrast
70
4
To save the new settings, highlight Done and press T.
To revert to the factory defaults, highlight Reset and press T.
The picture qualities you adjusted are automatically saved in the Preference mode (- “Selecting the picture mode,” above left).
30
HM66 (E/F) Web 213:276
HM66_EN.book Page 31 Thursday, February 23, 2006 2:49 PM
Chapter 5: Using the TV’s basic features
Using the closed caption mode
The closed caption mode has two options:
•
Captions—An on-screen display of the dialogue, narration, and sound effects of TV programs and videos that are closed captioned (usually marked “CC” in program guides).
•
Text—An on-screen display of information not related to the current program, such as weather or stock data (when provided by individual stations).
To view captions or text:
1
Press Y and open the Preferences menu.
2
Highlight
Closed Caption Mode
and press c.
3
Press B or b to select the desired closed caption mode and press T.
Preferences
Favorite Channels
Closed Caption Mode Off
Closed Caption Advanced
Input Labeling
Menu Language
Channel Browser Setup
English
Off
CC1
CC2
CC3
CC4
T1
T2
Navigate ENTER Select CH RTN Back EXIT Exit
•
To view captions:
Highlight CC1, CC2, CC3, or CC4. (CC1 displays translation of the primary language in your area.)
Giant pandas eat leaves.
•
Note: If the program or video you selected is not closed captioned, no captions will display on-screen.
To view text:
Highlight T1, T2, T3, or T4.
WORLD WEATHER
Temps Current
F C Weather
LONDON 51 11 Clear
MOSCOW
PARIS
ROME
TOKYO
57 14
53 12
66 19
65 18
Cloudy
Clear
Cloudy
Rain
•
Note: If text is not available in your area, a black rectangle may appear on your screen. If this happens, turn the
Closed Caption Mode Off.
To turn off the Closed Caption mode:
Select Off in step 3 above.
Note: A closed caption signal may not display in the following situations:
• When a videotape has been dubbed
• When the signal reception is weak
• When the signal reception is non-standard
Closed Caption Advanced
You can customize the closed caption display characteristics by changing the text size, type, edge, color, and the background color. You cannot set the Caption Text and
Background as the same color.
Notes:
• This feature is available for digital channels only.
• You cannot set the Caption Text and Background as the
same color.
To customize the closed captions:
1
Press Y and open the Preferences menu.
2
Highlight Closed Caption Advanced and press T.
3
Press B or b to highlight the characteristic you want to change, and then press C or c to select the format for that characteristic.
Closed Caption Advanced
Caption Size
Caption Text Type
Caption Text Edge
Caption Text Color
Background Color
Reset
Auto
Auto
Auto
Auto
Auto
Done
4
To save the new settings, highlight Done and press T.
To revert to the factory defaults, highlight Reset and press T.
Caption Size Auto, Small, Standard, Large
Caption Text
Type
Auto, Default, Mono w. Serif, Prof. w. Serif,
Mono w/o Serif, Prop w/o Serif, Casual,
Cursive, Small Capitals
Caption Text
Edge
Caption Text
Color
Background
Color
Auto, None, Raised, Depressed, Uniform,
Left Drop Shadow, Right Drop shadow
Auto, Black, White, Red, Green, Blue,
Yellow, Magenta, Cyan
Auto, Black, White, Red, Green, Blue,
Yellow, Magenta, Cyan
31
HM66 (E/F) Web 213:276
HM66_EN.book Page 32 Thursday, February 23, 2006 2:49 PM
Chapter 5: Using the TV’s basic features
Digital closed captions
You can use the Digital CC/Audio Selector to select digital closed caption services (if available), which will temporarily override closed captions for digital channels only.
When such services are not available, the Digital CC/Audio
Selector presents a default list of services. If the selected service is not available, the next best service will be used instead.
To select digital closed captions:
1
Press Y and open the Applications menu.
2
Highlight Digital CC/Audio Selector and press T.
4
Press O.
Applications
Channel Browser
Digital CC/Audio Selector
CableCARD
Navigate ENTER Select CH RTN Back EXIT Exit
3
Press B or b to select Closed Caption, and then press
C or c to select the desired service.
Closed Caption
Audio
CC 1
None
Adjusting the audio
Muting the sound
Press W to partially reduce (1/2 MUTE) or turn off (MUTE) the sound. Each time you press W, the mute mode will change in the following order:
1/2 Mute Mute Volume
If the closed caption mode is set to Off when you select
“MUTE” mode, the closed caption feature is automatically activated. To mute the audio without automatically activating the closed caption feature, use Z to set the volume to 0. See
“Using the closed caption mode” (- page 31) for more information on closed caption modes.
Using the digital audio selector
You can use the Digital CC/Audio Selector to conveniently switch between audio tracks on a digital channel (for those channels that have multiple audio tracks). This temporarily overrides the audio track chosen by the language option under
Audio Setup (see “Selecting stereo/SAP broadcasts,” on page 33).
To use the digital audio selector:
1
Press Y and open the Applications menu.
2
Highlight Digital CC/Audio Selector and press T.
Applications
Channel Browser
Digital CC/Audio Selector
CableCARD
Navigate ENTER Select CH RTN Back EXIT Exit
3
Press B or b to select Audio, and then press C or c to select the desired service.
Closed Caption
Audio
CC 1
None
4
Press O.
32
HM66 (E/F) Web 213:276
HM66_EN.book Page 33 Thursday, February 23, 2006 2:49 PM
Chapter 5: Using the TV’s basic features
Selecting stereo/SAP broadcasts
The multi-channel TV sound (MTS) feature allows you to output high-fidelity stereo sound. MTS also can transmit a second audio program (SAP) containing a second language, music, or other audio information (when provided by individual stations).
The MTS feature is not available when the TV is in VIDEO mode. When the TV receives a stereo or SAP broadcast, the word “STEREO” or “SAP” appears on-screen when E is pressed.
To listen to stereo sound:
1
Press Y and open the Audio menu.
2
Highlight Audio Setup and press T.
Audio
Audio Settings
Advanced Audio Settings
Audio Setup
3
In the MTS field, select Stereo.
Audio Setup
MTS
Language
Speakers
Optical Output Format
Reset
Stereo
English
On
Dolby Digital
Done
4
To save the new settings, highlight Done and press T.
To reset the settings to the factory defaults, highlight
Reset and press T.
Notes:
• If you leave the TV in Stereo mode because it will
automatically output the type of sound being broadcast
(stereo or monaural).
• If the stereo sound is noisy, select Mono to reduce the
noise.
To listen to an alternate language on an ATSC digital station (if available):
Highlight the Language field in step 3 above, and then press
C or c to select the language you prefer.
To listen to a second audio program on an analog station (if available):
Select SAP in step 3 above.
Notes:
• A second audio program (SAP) can be heard only on those
TV stations that offer it. For example, a station might broadcast another language as a second audio program. If you have SAP on, you will see the current program on the screen but hear the other language instead of the program’s normal audio.
• If you have SAP on and the station you are watching is not
broadcasting a second audio program, the station’s normal audio will be output. However, occasionally there is no sound at all in SAP mode. If this happens, set the MTS feature to Stereo mode.
Adjusting the audio quality
You can adjust the audio quality by adjusting the bass, treble, and balance.
To adjust the audio quality:
1
Press Y and open the Audio menu.
2
Highlight Audio Settings and press T.
3
Press b or B to highlight the item you want to adjust
(Bass, Treble, or Balance).
Audio Settings
Bass
Treble
Balance
StableSound
Reset
100
100
0
Done
Off
4
Press C or c to adjust the level.
•
C makes the bass or treble weaker or increases the
balance in the left channel (depending on the item selected).
• c makes the bass or treble stronger or increases the
balance in the right channel (depending on the item selected).
5
To save the new settings, highlight Done and press T.
To reset the settings to the factory defaults, highlight
Reset and press T.
33
HM66 (E/F) Web 213:276
HM66_EN.book Page 34 Thursday, February 23, 2006 2:49 PM
Chapter 5: Using the TV’s basic features
Using the StableSound
®
feature
The StableSound
®
feature limits the highest volume level to prevent extreme changes in volume when the signal source changes (for example, to prevent the sudden increase in volume that often happens when a TV program switches to a commercial).
To turn on the StableSound
®
feature:
1
Press Y and open the Audio menu.
2
Highlight Audio Settings and press T.
3
In the StableSound field, select On.
Audio Settings
Bass
Treble
Balance
StableSound
Reset
100
100
0
Done
On
4
To save the new settings, highlight Done and press T.
To revert to the factory defaults, highlight Reset and press T.
Note: The RESET function returns your audio adjustments to the following factory settings:
Bass . . . . . . . . . center (50)
Treble. . . . . . . . center (50)
Balance . . . . . . center (0)
StableSound. . . Off
To turn off the StableSound feature:
Select Off in step 3 above.
Turning off the built-in speakers
You can use this feature to turn off the TV speakers when you connect an audio system to your TV (- “Connecting a digital audio system” and “Connecting an analog audio system” in the
Installation Guide).
To turn off the built-in speakers:
1
Press Y and open the Audio menu.
2
Highlight Audio Setup and press T.
3
In the Speakers field, select Off.
Audio Setup
MTS
Language
Speakers
Optical Output Format
Reset
Stereo
English
Off
Dolby Digital
Done
4
To save the new settings, highlight Done and press T.
To revert to the factory defaults, highlight Reset and press T.
To turn on the built-in speakers:
Select On in step 3 above.
Selecting the optical audio output format
You can use this feature to select the optical audio output format when you connect a Dolby Digital decoder or other digital audio system to the Optical Audio Out terminal on the TV
(- “Connecting a digital audio system” in the Installation
Guide).
To select the optical audio output format:
1
Press Y and open the Audio menu.
2
Highlight Audio Setup and press T.
3
In the Optical Output Format field, select either
Dolby Digital or PCM, depending on your device.
Audio Setup
MTS
Language
Speakers
Optical Output Format
Reset
Stereo
English
On
Dolby Digital
Done
4
To save the new settings, highlight Done and press T.
To revert to the factory defaults, highlight Reset and press T.
34
HM66 (E/F) Web 213:276
HM66_EN.book Page 35 Thursday, February 23, 2006 2:49 PM
Chapter 5: Using the TV’s basic features
When the correct PIN code is entered, the Locks menu opens.
Using the Locks menu
The Locks menu includes the Enable Rating Blocking, Edit
Rating Limits, Channels Block, Input Lock, Front (control)
Panel Lock, and New PIN Code features. You can use these features after entering the correct PIN code.
Entering the PIN code
1
Press Y and highlight the Locks menu icon.
Locks
Enable Rating Blocking
Edit Rating Limits
Channels Block
Input Lock
Front Panel Lock
New PIN Code
Off
Off
Off
EXIT
Exit Navigate
ENTER Select CH RTN
Back
2
Press b, which displays the PIN code entry screen.
•
The Lock System screen (below) appears if a PIN code has not been stored. Press the Channel Number buttons to enter a new four-digit code, enter the code a second time to confirm, and press T.
Lock System
Please enter a 4 digit PIN code
Confirm PIN code
Locks
Enable Rating Blocking
Edit Rating Limits
Channels Block
Input Lock
Front Panel Lock
New PIN Code
Off
Off
Off
Navigate ENTER Select MENU Back EXIT Exit
If you cannot remember your PIN code
While the PIN code entering screen is displayed, press E four times within five seconds. The PIN code will be cleared and you can enter a new PIN code.
Changing your PIN code
1
Press Y and highlight the Locks menu icon.
2
Press b to display the PIN code entering screen.
3
Enter your four-digit PIN code and press T.
4
Press b to highlight New PIN Code and press T.
Cancel Done
•
The Locks/Active screen (below) appears if the PIN code is already stored. Use the Number buttons to enter your four-digit code and press T.
Locks Active
Please enter the 4 digit PIN code
* * * *
Cancel
Done
If the wrong PIN code is entered, the message “Incorrect PIN code, please try again!” appears. Highlight Retry and press
T. Enter the code again and press T.
Locks
Enable Rating Blocking
Edit Rating Limits
Channels Block
Input Lock
Front Panel Lock
New PIN Code
Off
Off
Off
Navigate ENTER Select MENU Back EXIT Exit
5
Press the Number buttons to enter a new four-digit code.
Retype the numbers to confirm the PIN code you entered.
6
Press T. The new PIN code is now active.
New PIN Code
Please enter a 4 digit PIN code
* * * *
Confirm PIN code
* * * *
Cancel
Done
35
HM66 (E/F) Web 213:276
HM66_EN.book Page 36 Thursday, February 23, 2006 2:49 PM
Chapter 5: Using the TV’s basic features
Blocking TV programs and movies by rating (V-Chip)
Some TV programs and movies include signals that classify the content of the program (violence, sex, dialog, language).
The V-Chip feature in this TV detects the signals and blocks the programs according to the ratings you select. (See the tables at below right for rating descriptions.)
Note: Rating blocking is a function of the V-Chip feature in this
TV, which supports the U.S. V-Chip system only.
To block and unblock TV programs and movies:
1
Press Y and highlight the Locks menu icon.
2
Press b to display the PIN code entering screen.
3
Enter your four-digit PIN code and press T.
4
Press b to highlight Enable Rating Blocking.
5
Press c and b to select On, and press T.
Locks
Enable Rating Blocking
Edit Rating Limits
Channels Block
Input Lock
Front Panel Lock
New PIN Code
Off
Off
Off
Off
On
EXIT
Exit Navigate
ENTER Select MENU
Back
6
Press b to highlight Edit Rating Limits and press T.
The Edit Rating Limits screen (below) appears.
7
Press BbC c and then press T to select the level of blocking you prefer. A box with an “5” is a rating that will be blocked. As you highlight a rating, a definition for the rating appears at the bottom of the screen.
8
When done selecting the ratings you want to block, highlight Done and press T.
Edit Rating Limits
TV (V-CHIP) FV D L S V
TV-Y
TV-Y7
TV-G
TV-PG
TV-14
TV-MA
"None" Rated
Movies
G
PG
PG-13
R
NC-17
X
Children
Youth
Alt RS
Cancel
Done
Blocking TV programs and movies by alternate ratings:
The alternate rating system is provided by some broadcasters as a supplement the standard V-Chip ratings. This system is dependant on the broadcaster’s information.
1
Repeat steps 1-6 above.
2
Highlight Alt RS and press T. The Edit Alternate
Ratings screen will appear. (This button will only be available if your television has detected that the broadcaster is send alternate ratings with that program.)
3
Press B b C c and then press T to select the level of blocking you prefer. A box with and “5” is a rating that will be blocked. (The information contained within this menu window will depend on what the broadcaster is providing.)
4
When done selecting the ratings you want to block, highlight Done and press T.
5
In the Edit Rating Limits screen, highlight Done and press T.
Edit Alternate Ratings
Humor Level
DH
MH
H
VH
EH
Intelligence level
VL
LL
NL
HL
VH
TEST-MAX
Cancel
Done
Note: The above illustration is example data only. The
Alternate Ratings screen on your TV may not look the same.
Independent rating system for broadcasters
Ratings Description and Content themes
TV-MA
TV-14
TV-PG
TV-G
TV-Y7,
TV-Y7FV
TV-Y
Mature Audience Only (This program is specifically designed to be viewed by adults and therefore may be unsuitable for children under 17.)
L) Crude or indecent language S) Explicit sexual activity V) Graphic violence
Parents Strongly Cautioned (This program contains some material that many parents would find unsuitable for children under 14 years of age.)
D)
Intensely suggestive dialog
L)
Strong, coarse language
S)
Intense sexual situations
V)
Intense violence
Parental Guidance Suggested (This program contains material parents may find unsuitable for younger children.)
D)
Some suggestive dialog
L)
Infrequent coarse language
S)
Some sexual situations
V)
Moderate violence
General Audience (Most parents would find this program suitable for all ages.)
Directed to Older Children (This program is designed for children age 7 and above. Note: Programs in which fantasy violence may be more intense or more combative than other programs in this category are designated Y7FV.)
All Children (This program is designed to be appropriate for all children.)
36
HM66 (E/F) Web 213:276
HM66_EN.book Page 37 Thursday, February 23, 2006 2:49 PM
Chapter 5: Using the TV’s basic features
Independent rating system for movies
Ratings Description and Content themes
X
NC-17
X-rated (For adults only)
Not intended for anyone 17 and under
R
PG-13
PG
G
Restricted (Under 17 requires accompanying parent or adult)
Parents Strongly Cautioned (Some material may be inappropriate for children under 13)
Parental Guidance Suggested (Some material may not be suitable for children)
General Audience (Appropriate for all ages)
Notes:
• If you place an “
5” in the box next to “‘None’ Rated,”
programs rated “None” will be blocked; however, programs that do not provide any rating information will not be blocked.
• To display the rating of the program you are watching, press
E on the remote control. If it is rated “None,” the word
“NONE”appears in the RECALL screen (as shown below right). If rating information is not provided, no rating will appear in the RECALL screen.
L V NONE
Blocking channels
With the Channels Block feature, you can block specific channels. You will not be able to tune blocked channels unless you clear the setting first.
To block channels:
1
Press Y and highlight the Locks menu icon.
2
Press b to display the PIN code entering screen.
3
Enter your four-digit PIN code and press T (- page 35).
4
Press b to highlight Channels Block and then press T.
5
Using BbC c buttons, select the input for which you want to change the rating limits (ANT1, or ANT2) and press T.
A list of the channels available for that input will be displayed along with the call letters for each channel, if available.
6
Press Bb to highlight the channel you want to block, and press T, which puts an “5” in the box next to that channel.
Channels Block
4
5
6
7
1
2
3
8
9
10
ANT 2
ANT 1
ANT 2
Allow All
Block All
Cancel
Done
7
Repeat step 6 for other channels you want to block.
8
Highlight Done and press T.
To unblock individual channels:
In step 6 above, press Bb to highlight the channel you want to unblock, and then press T to remove the “5” from the box, and then highlight Done, and then press T.
To block all channels at once:
Highlight Block All in step 6 above, and then highlight Done, and press T.
To unblock all locked channels at once:
Highlight Allow All in step 6 above, and then highlight Done and press T.
Channels Block
3
4
5
1
2
6
7
8
9
10
ANT 1
ANT 1
ANT 2
Allow All
Block All
Cancel
Done
Locks
Enable Rating Blocking
Edit Rating Limits
Channels Block
Input Lock
Front Panel Lock
New PIN Code
Off
Off
Off
Navigate
ENTER Select MENU
Back
EXIT
Exit
(continued)
37
HM66 (E/F) Web 213:276
HM66_EN.book Page 38 Thursday, February 23, 2006 2:49 PM
Chapter 5: Using the TV’s basic features
Unlocking programs temporarily
If you try to tune the TV to a program that exceeds the rating limits you set, the TV will enter program lock mode and the following message will appear on-screen:
This program exceeds the rating limit you set.
Push 'mute' to enter PIN.
You can either temporarily unlock the program or select an unlocked program to watch.
To temporarily unlock the program:
1
Press W.
2
Enter your four-digit PIN code and press T. If the correct code is entered, the program lock mode is released and the normal picture appears. All locking is disabled until the
TV is turned off, and will be enabled when the TV is turned on again.
Locks Active
Enter PIN code to temporaily unblock.
* * * *
Cancel
Done
Using the input lock feature
You can use the Input Lock feature to lock the video inputs
(VIDEO 1, VIDEO 2, ColorStream HD-1, ColorStream
HD-2, HDMI 1, and HDMI 2) and channels 3 and 4. You will not be able to view the input sources or channels until you unlock the inputs.
To lock/unlock the video inputs:
1
Press Y and highlight the Locks menu icon.
2
Press b to display the PIN code entering screen.
3
Enter your four-digit PIN code and press T.
4
Press b to highlight Input Lock and press c.
5
Press B or b to select the level of video input locking you prefer, as described below.
Video: Locks VIDEO 1, VIDEO 2, ColorStream HD1/
HD2, HDMI 1/HDMI 2.
Video+: Locks VIDEO 1, VIDEO 2, ColorStream HD1/
HD2, HDMI 1/HDMI 2, and channels 3 and 4.
•
Select Video+ if you play video tapes via an ANT input.
•
When a CableCARD™ is inserted, Video+ will not lock channels 3 and 4.
Locks
Enable Rating Blocking
Edit Rating Limits
Channels Block
Input Lock
Front Panel Lock
New PIN Code
Off
Off
Off
Off
Video
Video +
Navigate ENTER Select MENU Back EXIT Exit
Off: Unlocks all video inputs and channels 3 and 4.
6
Press T.
38
HM66 (E/F) Web 213:276
HM66_EN.book Page 39 Thursday, February 23, 2006 2:49 PM
Chapter 5: Using the TV’s basic features
Using the control panel lock feature
You can lock the control panel to prevent your settings from being changed accidentally (by children, for example). When the control panel lock is On, none of the controls on the TV control panel will operate except POWER.
To lock the control panel:
1
Press Y and highlight the Locks menu icon.
2
Press b to display the PIN code entering screen.
3
Enter your four-digit PIN code and press T.
4
Press b to highlight Front Panel Lock.
5
Press c and B or b to highlight On and press T. When the control panel is locked and a button on the control panel except POWER button is pressed, the message
“NOT AVAILABLE” appears.
Setting the sleep timer
You can set the sleep timer to turn off the TV after a set length of time (maximum of 180 minutes).
To set the sleep timer:
Press [ on the remote control to set the length of time until the TV turns off. Repeatedly press [ to increase the time in
10-minute increments or press B or b to increase or decrease the time in 10-minute increments, to a maximum of 180 minutes.
To cancel the sleep timer:
Press [ until it is set to 0 minutes.
To set the sleep timer using the on-screen menus:
1
Press Y and open the Setup menu.
2
Highlight Sleep Timer and press T.
Locks
Enable Rating Blocking
Edit Rating Limits
Channels Block
Input Lock
Front Panel Lock
New PIN Code
Off
Off
Off
Off
On
Navigate ENTER Select MENU Back EXIT Exit
To unlock the control panel:
Highlight Off in step 5 above, or press and hold the
VOLUME – button on the TV control panel for about 10 seconds until the volume icon appears on-screen.
Setup
Installation
Sleep Timer
ColorStream HD1 Audio
HDMI 1 Audio
ColorStream HD2 Audio
HDMI 2 Audio
Quick Restart
No
Auto
No
Auto
On
Navigate ENTER Select CH RTN Back EXIT Exit
3
Press the Number buttons to enter the length of time in
10-minute increments.
Sleep Timer
Enter total minutes until the TV turns off automatically (Maximum
180 minutes)
1 2 0
Cancel
4
Highlight Done and press T.
Done
Notes:
• When a power failure occurs, the sleep timer setting
may be cleared.
• To display the amount of time left on the sleep timer,
press
E.
To display the remaining sleep time:
Press [.
Sleep Timer
120 Minutes
Note: A message will display on-screen when there is one minute remaining on the sleep timer.
39
HM66 (E/F) Web 213:276
HM66_EN.book Page 40 Thursday, February 23, 2006 2:49 PM
Chapter 5: Using the TV’s basic features
Displaying TV setting information on-screen using RECALL
To display TV setting information on-screen:
Press E on the remote control.
The following information will display on-screen
(if applicable):
STEREO
NC-17
Sleep Timer: 18 min.
Lamp High Bright
Natural
480i
ANT 1
CABLE
81-1
•
•
•
•
Sample RECALL screen
Current input (ANT 1, ANT 2, VIDEO 1, etc.)
If ANT 1 or ANT 2 is the current input, whether it is Cable
TV (“CABLE”) or off-air (“TV”)
Channel number (if in ANT 1 or ANT 2 mode)
Signal strength indicator (bar graph in lower right corner of screen; for ATSC signal only)
•
•
•
•
•
•
Note: The signal strength indicator will react to fading and increasing signals.
Remaining time on sleep timer (if set)
Stereo or SAP audio status
V-Chip rating status
Picture size
Video resolution
Lamp mode (appears only if the TV is in High Bright mode)
To close the RECALL screen:
Press E again.
Understanding the auto power off feature
The TV will automatically turn itself off after approximately
15 minutes if it is tuned to a vacant channel or a station that completes its broadcast for the day. This feature functions in
ANT 1 and ANT 2 modes only.
Understanding the last mode memory feature
If the power is cut off while you are viewing the TV, the
Last Mode Memory feature automatically turns on the TV when the power is resupplied.
Note: You should unplug the TV’s power cord if it is possible that you will be away from the TV for an extended period of time after the power is restored.
40
HM66 (E/F) Web 213:276
HM66_EN.book Page 41 Thursday, February 23, 2006 2:49 PM
Chapter 6: Using the TV’s advanced features
Using the advanced picture settings features
Using dynamic contrast
When dynamic contrast is set to
On
, the TV will detect changes in the picture quality that affect the appearance of your contrast settings and then automatically adjust the video.
When dynamic contrast is set to
Off
, the settings selected in the
Contrast
field in
Picture Settings
will be used.
To select dynamic contrast preferences:
\
1
Press Y and open the
Video
menu.
2
Highlight
Advanced Picture Settings
and press T.
3
In the
Dynamic Contrast
field, select either
On
or
Off
.
Advanced Picture Settings ANT 1
Dynamic Contrast
CableClear
MPEG Noise Reduction
Color Temperature
Lamp Mode
Game Mode
On
Auto
Low
Cool
Low Power
Off
Reset Done
4
To save the new settings, highlight
Done
and press T. To revert to the factory defaults, highlight
Reset
and press
T.
Note: If you select the Movie picture mode and then set the dynamic contrast to On, the picture mode will automatically change to Preference in the Picture
Settings menu.
Using CableClear
®
/DNR (digital noise reduction)
The CableClear
®
digital noise reduction feature allows you to reduce visible interference in your TV picture. This may be useful when receiving a broadcast with a weak signal
(especially a Cable channel) or playing a noisy video cassette or disc.
To change the CableClear/DNR settings:
1
Press Y and open the Video menu.
2
Highlight Advanced Picture Settings and press T.
3
In the CableClear/DNR field, select your desired setting.
Advanced Picture Settings
Dynamic Contrast
CableClear
MPEG Noise Reduction
Color Temperature
Lamp Mode
Game Mode
Reset
On
Auto
Low
Cool
Low Power
Off
Done
ANT 1
Notes:
• If the current input is ANT 1, ANT 2, VIDEO 1, or VIDEO
2, the menu will display the text “CableClear.” The available selections are Off, Low, Middle, High, and
Auto.
• If the current input is ColorStream HD1, ColorStream
HD2, or HDMI, the menu will display the text DNR. The available selections are Off, Low, Middle, High and
Auto. Auto will react proportionally to the strength of the noise. Low, Middle, and High will reduce the noise in varying degrees, from lowest to highest, respectively.
4
To save the new settings, highlight Done and press T.
To revert to the factory defaults, highlight Reset and press T.
Using MPEG noise reduction
The MPEG noise reduction feature allows you to reduce visible interference caused by MPEG compression. Choices for MPEG noise reduction are
Off
,
Low
,
Middle
, and
High
.
Off
is automatically selected when this feature is disabled (“grayed out”).
To select the MPEG noise reduction level:
1
Press Y and open the
Video
menu.
2
Highlight
Advanced Picture Settings
and press T.
3
Press B or b to highlight the MPEG Noise Reduction field, and then press C or c to select either Off, Low,
Middle or High.
Advanced Picture Settings
Dynamic Contrast
CableClear
MPEG Noise Reduction
Color Temperature
Lamp Mode
Game Mode
Reset
On
Auto
Low
Cool
Low Power
Off
Done
ANT 1
4
To save the new settings, highlight Done and press T.
To revert to the factory defaults, highlight Reset and press T.
(continued)
41
HM66 (E/F) Web 213:276
HM66_EN.book Page 42 Thursday, February 23, 2006 2:49 PM
Chapter 6: Using the TV’s advanced features
Selecting the color temperature
You can change the quality of the picture by selecting from three preset color temperatures (cool, medium, and warm), as described below.
Mode
cool medium warm
Picture Quality
blueish neutral reddish
To select the color temperature:
1
Press Y and open the Video menu.
2
Highlight Advanced Picture Settings and press T.
3
In the Color Temperature field, select the mode you prefer (Cool, Medium, or Warm).
Advanced Picture Settings
Dynamic Contrast
CableClear
MPEG Noise Reduction
Color Temperature
Lamp Mode
Game Mode
Reset
On
Auto
Low
Cool
Low Power
Off
Done
ANT 1
4
To save the new settings, highlight Done and press T.
To revert to the factory defaults, highlight Reset and press T.
Note: If you select one of the factory-set picture modes
(Sports, Standard, or Movie) and then change the color temperature mode, the picture mode automatically changes to Preference in the Picture Settings menu.
Selecting the lamp mode
You can select either the High Bright or Low Power lamp mode.
•
The High Bright mode is useful when additional picture brightness is desired (such as in a bright room).
To select the lamp mode:
1
Press Y and open the Video menu.
2
Highlight Advanced Picture Settings and press T.
Video
Picture Settings
Advanced Picture Settings
Theater Settings
Navigate ENTER Select CH RTN Back EXIT Exit
3
In the Lamp Mode field, select High Bright or Low
Power, whichever you prefer.
Advanced Picture Settings
Dynamic Contrast
CableClear
MPEG Noise Reduction
Color Temperature
Lamp Mode
Game Mode
Reset
On
Auto
Low
Cool
Low Power
Off
Done
ANT 1
4
To save the new settings, highlight Done and press T.
To revert to the factory defaults, highlight Reset and press T.
Note: If you set the lamp mode to Low Power, each time you turn on the TV, the lamp will start out in High Bright mode but will switch to Low Power mode after a short period of time. You may notice a change in screen brightness when this happens. This is normal and is not a sign of malfunction.
42
HM66 (E/F) Web 213:276
HM66_EN.book Page 43 Thursday, February 23, 2006 2:49 PM
Chapter 6: Using the TV’s advanced features
Using the Game Mode feature
You can use the Game Mode feature for shorter frame delays when playing a video game requiring split-second timing between the on-screen display and input from the controller
(such as music creation and high-action games).
Note: To use the Game Mode feature, the current video input must be Video 1, Video 2, ColorStream HD1,
ColorStream HD2, HDMI 1 or HDMI 2. The Game Mode cannot be turned on when any other video input is selected.
To turn on Game Mode:
1
Press Y and open the Video menu.
2
Highlight Advanced picture settings and press T.
3
Press B or b to highlight the Game Mode field, and then press C or c to select On.
Advanced Picture Settings
Dynamic Contrast
CableClear
MPEG Noise Reduction
Color Temperature
Lamp Mode
Game Mode
Reset
On
Auto
Low
Cool
Low Power
On
Done
Video 1
To turn off Game Mode:
Select Off in step 3 above or change the video input.
You can change the video input in any of the following ways:
• pressing
+ on the remote control (- page 23);
• changing the channel using the Numbers or
< / ,, R,
3 C, # c, or M / m;
• Turning the TV off and back on again will set Game Mode to
Off.
Using the advanced audio settings features
Using the SRS WOW™ surround sound feature
WOW™ is a special combination of SRS Labs audio technologies (SRS 3D, SRS FOCUS, and SRS TruBass) that creates a thrilling surround sound experience with deep, rich bass from stereo sound sources. Your TV’s audio will sound fuller, richer, and wider.
To adjust the WOW™ settings:
1
Put the TV in STEREO mode (- “Selecting stereo/SAP broadcasts” page 33).
2
Press Y and open the Audio menu.
3
Highlight Advanced Audio Settings and press T.
4
Press b or B to highlight the WOW feature you want to adjust, and then press C or c to adjust the item.
Advanced Audio Settings
WOW: SRS 3D
WOW: SRS FOCUS
WOW: SRS TruBass
Reset
Off
Off
Low
Done
•
WOW: SRS 3D — To turn the surround sound effect
On or Off.
Note: If the broadcast is monaural, the SRS 3D effect will not work.
•
•
WOW: SRS Focus — To turn the vocal emphasis effect
On or Off.
WOW: SRS TruBass — To select the desired bass expansion level (Off, Low, or High).
5
To save the new settings, highlight Done and press T.
To revert to the factory defaults, highlight Reset and press T.
WOW, SRS and l symbol are trademarks of SRS Labs, Inc.
WOW technology is incorporated under license from SRS Labs, Inc.
43
HM66 (E/F) Web 213:276
HM66_EN.book Page 44 Thursday, February 23, 2006 2:49 PM
General troubleshooting
Before calling a service technician, please check this entire chapter for a possible cause of the problem and some solutions you can try.
Black box on screen
• The Closed Caption feature is set to one of the Text modes (T1, T2, T3, or T4). Set the Closed Caption feature to Off (- page 31).
TV plays a recorded anouncement when LEDs are blinking
•
When certain non-standard conditions occur, the LEDs on the TV will blink and the TV will play a recorded
“voice announcement” describing the condition (see
“LED indications” on page 46 for details).
TV stops responding to controls
•
If the TV stops responding to the controls on the remote control or TV control panel and you cannot turn off the
TV, press and hold the POWER button on the TV control panel for 5 or more seconds to reset the TV.
Other problems
•
If your TV’s problem is not addressed in this
Troubleshooting section or the recommended solution has not worked, use the Restore Factory Defaults procedure (- page 22).
TV will not turn on
•
•
•
•
•
Make sure the power cord is plugged in, and then press p.
The remote control batteries may be dead. Replace the batteries or try the control panel buttons.
If you have recently replaced the lamp unit, make sure the lamp unit and lamp unit door are installed properly
(- pages 47–49).
The lamp unit may need to be replaced (- pages 47–49).
Also see “LED indications” (- page 46).
If the TV is powered off and then quickly on again when the lamp unit is hot, it may take several minutes for the picture to appear on-screen. This is a property of DLP TV lamp technology and is NOT a sign of malfunction. For details, see IMPORTANT NOTICE ABOUT “HOT
LAMP RESTART” (- page 2).
Picture problems
General picture problems
•
Check the antenna/cable connections (- Installation
•
Guide).
Press + on the remote control or INPUT on the TV control panel and select a valid video input source
•
•
(- page 23). If no device is connected to any of the inputs on the TV, no picture will display when you select that particular input source. For device connection details, see the Installation Guide.
Antenna reception may be poor. Use a highly directional outdoor antenna (if applicable).
The station may have broadcast difficulties. Try another channel.
44
Chapter 7: Troubleshooting
•
•
•
•
Adjust the picture qualities (- page 30).
If you are using a VCR, make sure L on the remote control is set correctly (- page 9).
If you have two VCRs connected to your TV, make sure you have not connected the same VCR to the TV’s output and input connections at the same time (- Installation
Guide).
Do not connect both a standard video cable and an Svideo cable to the same set of VIDEO inputs (VIDEO 1, or VIDEO 2) at the same time (- Installation Guide).
Noisy picture
•
If you are watching a tuned analog channel (off-air broadcast or Cable TV), set the CableClear
®
/DNR feature to AUTO to reduce visible interference in the TV picture (- page 41).
Video Input Selection problems
• If the Input Selection window does not appear when you press + on the remote control or INPUT on the TV control panel, press + a second time, which will change to the next video input source and display the Input
Selection window.
Cannot view external signals or channel 3 or 4
•
If you cannot view signals from external devices connected to VIDEO 1, VIDEO 2, or ColorStream
®
, or from channels 3 or 4, make sure the Input Lock is set to Off (- page 38).
Poor color or no color
•
The station may have broadcast difficulties. Try another
•
• channel.
Adjust the Tint and/or Color (- page 30).
When the ColorStream
®
signal source is active, the
VIDEO OUT terminal outputs blank video. To receive video from the VIDEO OUT signal, a standard video or
S-video IN terminal must be used instead of the
ColorStream
®
connections.
Picture brightness changes soon after turning on TV
•
If you set the lamp mode to Low Power, each time you turn on the TV, the lamp will start out in High Bright mode but will switch to Low Power mode after a short period of time. You may notice a change in screen brightness when this happens. This is normal and is not a sign of malfunction (- page 42).
Poor composite or S-video picture
• If the TV is connected to an external A/V device (e.g.,
DVD player, video game system, set-top box, etc.) try using a ColorStream or HDMI video connection instead.
Picture and sound are out of sync
• As with all products that contain a digital display, in rare instances, when viewing certain content (e.g.. television broadcasts, video games, DVDs), you may notice that the sound and picture are slightly out of sync. This phenomenon can be caused by various factors including, without limitation, video processing within the TV, video processing in an attached gaming system, and video processing or different compression rates used by broadcasters in their programming. You may want to try one or more of the following suggestions, which may help to reduce the effect of this phenomenon:
HM66 (E/F) Web 213:276
HM66_EN.book Page 45 Thursday, February 23, 2006 2:49 PM
Chapter 7: Troubleshooting
– If the TV is connected to an A/V receiver that has a programmable audio delay feature, use this feature to help synchronize the sound to the picture.
– If you notice this phenomenon only on certain TV channels, please contact your local broadcast, cable, or satellite provider to inform them of this issue.
Sound problems
•
•
•
•
•
•
•
•
Check the antenna/cable connections (- Installation
Guide).
The station may have broadcast difficulties. Try another channel.
The sound may be muted. Press z.
If you hear no sound, try setting the MTS feature to
Stereo mode (- page 33).
Make sure the Speakers function in the Audio Setup menu is set correctly (- page 34).
If you are not receiving a second audio program from a known SAP source, make sure the MTS feature is set to
SAP mode (- page 33).
If you hear audio that seems “incorrect” for the program you are watching (such as music or a foreign language), the SAP mode may be on. Set the MTS feature to Stereo mode (- page 33).
When using an external audio amplifier, if you connect the amplifier to the VAR. AUDIO OUT terminals, the volume of the TV and amplifier must be set above 0 or you will not hear any sound (- Installation Guide).
Remote control problems
•
•
•
•
•
Make sure the remote control is set to the correct device mode (- pages 9–10).
Remove all obstructions between the remote control and the TV.
The remote control batteries may be dead. Replace the batteries (- page 7).
Your TV remote control may not operate certain features on your external device. Refer to the owner’s manual for your other device to determine its available features. If your TV remote control does not operate a specific feature on another device, use the remote control that came with the device (- pages 9–13).
If the TV still does not act as expected, use the Restore
Factory Defaults procedure (- page 22).
Channel tuning problems
•
•
•
•
Make sure the remote control is set to the correct device mode (- page 8).
The channel may have been erased from the channel memory by the Channel Add/Delete feature. Add the channel to the channel memory (- page 17).
The channel may be blocked by the Channels Block feature. Unblock the channel (- page 37).
If you are unable to tune digital channels, check the antenna configuration (- page 16). If you are still unable to tune digital channels, clear all channels from the channel list (- page 18) and reprogram channels into the channel memory (- page 17). If you are still unable to tune digital channels, use the Restore Factory Defaults procedure (- page 22). Also see “TV stops responding to controls” and “Other problems” (- page 44).
Closed caption problems
•
•
•
If the program or video you selected is not closedcaptioned, no captions will display on-screen
(- page 31).
If text is not available, a black rectangle may appear onscreen. If this happens, turn off the closed caption feature
(- page 31).
A closed caption signal may not display correctly in the following situations: a) when a videotape has been dubbed; b) when the signal reception is weak; or c) when the signal reception is nonstandard (- page 31).
Rating blocking (V-Chip) problems
•
•
If you forget your PIN code: While the PIN code entering screen is displayed, press E four times within 5 seconds. The PIN code you previously stored will be cleared (- page 35).
The V-Chip feature is available for the U.S. V-Chip system only (- page 36).
45
HM66 (E/F) Web 213:276
HM66_EN.book Page 46 Thursday, February 23, 2006 2:49 PM
Chapter 7: Troubleshooting
LED indications
The yellow blue and red/green LED lights on the TV (at the bottom center of the TV) indicate the TV’s status, as described below:
Note: If the TV loses A/C power (e.g., a power outage occurs or the power cord is unplugged), when power is restored, the yellow
LED will blink while the TV is booting until the remote control is usable. This is normal and is not a sign of malfunction.
TV front
Yellow LED Blue LED Red/Green LED
“Voice announce” feature
When certain non-standard conditions occur, the LEDs on the TV will blink and the TV will play a recorded
“voice announcement” describing the condition (see the table below for the specific conditions that include a voice announcement).
To repeat the voice announcement and hear additional information, press the MENU button on the TV while the
LEDs are blinking.
LED Indication Condition Solution Voice announce
1) Blue is ON (solid).
2) Yellow blinks.
The TV is operating properly.
In LPS mode (standby with Quick Restart ON).
– –
See “Setting the Quick Restart™ feature” (
- page 20).
–
3) Blue is ON (solid).
Yellow blinks.
The lamp is not working properly.
The TV will automatically try to restart itself eight times
(see item #4).
Note: If the TV is powered off and then quickly on again when the lamp unit is hot, it may take several minutes for the picture to appear on-screen. This is a property of
DLP TV lamp technology and is NOT a sign of malfunction. For details, see “Setting the Quick
Restart™ feature” and “IMPORTANT NOTICE ABOUT
HOT LAMP RESTART” (
- page 21).
–
4) Yellow is ON
(solid). Red blinks.
The lamp is not working properly after the eighth automatic restart (see item #3).
Turn the TV OFF and then ON again. If the problem persists, contact Consume Solutions at
1-800-631-3811.
“Lamp not working”
5) Yellow is ON
(solid).
The lamp unit door is not seated properly.
Turn OFF the TV and unplug the power cord. Review
“Lamp unit replacement and care” in Chapter 8 to ensure that the lamp door is installed securely.
“Lamp door is open.”
6) Red blinks.
7) Blue is ON (solid).
Green blinks.
Fan stopped (POD).
8) Blue blinks slowly. Abnormal operation of
BUS line.
9) Blue blinks quickly. Power Protect
Detection.
10)Blue blinks quickly.
Red blinks.
11)Blue blinks quickly.
Yellow blinks.
Red blinks.
Fan stopped
(light engine).
The color wheel has stopped.
An abnormal temperature increase has occurred.
Turn OFF the TV and unplug the power cord. Plug the power cord in again and turn ON the TV.
Turn OFF the TV. Check to make sure all slots and openings in the TV cabinet are not covered, blocked, or dusty. Turn ON the TV again.
“Fan stopped.”
“Fan stopped.”
–
–
“Color wheel stopped.”
“Temperature warning.”
If, after trying solutions, the problem still exists:
•
In the U.S., call TACP Consumer Solutions at 1-800-631-3811.
•
In Canada, locate the nearest Toshiba authorized service depot by directing your web browser to www.toshiba.ca; click
“Home Entertainment,” and then click “Support.”
46
HM66 (E/F) Web 213:276
HM66_EN.book Page 47 Thursday, February 23, 2006 2:49 PM
Chapter 8: Appendix
Lamp unit replacement and care
Replacing the lamp unit
(User-replaceable component)
WARNING: RISK OF ELECTRIC
SHOCK!
TO REDUCE THE RISK OF ELECTRIC
SHOCK, NEVER REMOVE TV COVERS, EXCEPT AS
SPECIFIED HEREIN. REFER ALL SERVICING NOT
SPECIFIED IN THIS MANUAL TO QUALIFIED SERVICE
PERSONNEL. Failure to follow this WARNING may result in death or serious injury.
The light source for this TV is a mercury lamp with internal atmospheric pressure that increases during use. The lamp has a limited service life that varies depending on product use and user settings.
As is generally the case with all projection TVs that use projection lamps as a light source, the brightness of the lamp in this TV may vary somewhat over the expected service life and will generally decrease over time. Because of the many variables that can affect the useful service life of the lamp, your experience may vary from other users.
Note : The lamp is warranted only for the periods and to the extent set forth in the Limited Warranty applicable to this set.
See “Limited United States Warranty” (
- page 51) or “Limited
Canada Warranty” (
- page 52), as applicable.
•
•
If you use the lamp beyond its service life:
you may notice a reduction in the colors and/or brightness of the picture; and the strength of the quartz glass in the lamp will be reduced and the lamp may rupture (often making a loud noise when this happens). If the lamp ruptures, the TV will not operate until the lamp unit is replaced.
CAUTION: Always handle the lamp unit with care.
The lamp unit in this TV was designed for safe replacement by consumers; however, if the lamp unit is subjected to intentional abuse (such as excessive mechanical abuse or handling by children or pets), the unit may break, exposing sharp edges or pinch points.
When to replace the lamp unit
•
•
•
You should replace the lamp unit:
if the picture darkens and/or colors fade; if the screen (lamp) does not light (LED indication #4,
- page 46); or if you hear a loud noise and the picture goes black, which may indicate a lamp rupture (LED indication #4,
- page 46).
To obtain a replacement lamp unit:
In warranty:
Out of warranty:
In the U.S.
Visit www.tacp.toshiba.com/service or call toll-free 1-800-631-3811.
Visit www.ceaccessories.toshiba.com or consult your consumer electronics dealer.
In Canada
Locate a Toshiba parts distributor by visiting
www.toshiba.ca. Click “Home Entertainment” and then click “Support.”
Always replace the lamp unit with the model currently recommended by Toshiba.
For more information, please contact us at the telephone numbers listed above, or visit the websites listed above, as applicable.
Using any lamp other than those recommended by
Toshiba may cause damage to the TV and/or lamp.
SUCH DAMAGE IS NOT COVERED UNDER YOUR
TOSHIBA WARRANTY.
47
HM66 (E/F) Web 213:276
HM66_EN.book Page 48 Thursday, February 23, 2006 2:49 PM
Chapter 8: Appendix
How to replace the lamp unit
WARNING: RISK OF ELECTRIC
SHOCK!
TO REDUCE THE RISK OF ELECTRIC
SHOCK, NEVER REMOVE TV COVERS, EXCEPT AS
SPECIFIED HEREIN. REFER ALL SERVICING NOT
SPECIFIED IN THIS MANUAL TO QUALIFIED SERVICE
PERSONNEL. Failure to follow this WARNING may result in death or serious injury.
•
•
Required tools:
Manual screwdrivers (Phillips and slotted)
Soft, lint-free gloves
1
Turn off the TV and unplug the power cord.
WARNING: Eye damage may result from directly viewing the light produced by this lamp.
Always turn off the TV and unplug the power cord before opening the lamp unit door.
2
STOP! Allow the lamp to cool for at least one (1) hour
before replacing it.
4
Using a manual Phillips screwdriver, loosen the two screws on the lamp unit.
Lamp unit screws
WARNING: RISK OF ELECTRIC
SHOCK!
The lamp unit door is provided with an interlock to reduce the risk of electric shock and excessive ultraviolet radiation. Never defeat its purpose or attempt
to service without removing the lamp unit door
completely. Failure to follow this WARNING may result in death or serious injury.
[
5
Grasp the lamp unit handle and gently pull the lamp unit straight out of the TV. Set the old lamp unit aside
(- “Disposing of the used lamp unit” on page 49).
3
On the lamp unit door on the back of the TV, loosen the screw by using manual screwdriver, and then remove the lamp unit door.
Lamp unit door detail
TV back
NOTE:
Wear soft, lint-free gloves when replacing the lamp unit.
6
Carefully insert the new lamp unit straight into the TV until it is fully seated.
Loosen screw using manual screwdriver
48
HM66 (E/F) Web 213:276
HM66_EN.book Page 49 Thursday, February 23, 2006 2:49 PM
Chapter 8: Appendix
Notes:
• Never subject the lamp unit to excessive shock.
• Never touch the lamp unit glass or otherwise get it dirty.
Doing so may affect the image quality and reduce the service life of the lamp. See “Cleaning the lamp unit glass” below.
CLEANING THE LAMP UNIT GLASS
If you accidentally touch the lamp unit glass or otherwise get it dirty, wipe it with a lint-free lens cleaning cloth (such as a cloth for cleaning camera lenses or eyeglasses).
CAUTION:
NEVER clean a hot lamp with any type of flammable liquid or aerosol cleaning agent.
Many ordinary cleaning agents (such as glass cleaners) contain chemicals that may be flammable at certain temperatures. If the lamp unit is not allowed to cool for at least one (1) hour, such chemicals may ignite.
9
Replace the screw and tighten using a manual screwdriver.
Hand tighten using manual screwdriver
Lamp unit door
NOTE:
Make sure the lamp unit door is installed securely; otherwise, the TV may not turn on.
7
Using a manual phillips screwdriver, tighten the two lamp unit screws.
Note: Hand-tighten only. Do not use an electric screwdriver.
Lamp unit screws
(use manual Phillips screwdriver only)
NOTE :
Make sure the lamp unit and screws are installed securely; otherwise, the TV may not turn on and the lamp life may be shortened.
8
Reattach the lamp unit door, making sure to insert the hooks on the left side of the lamp unit door inside the opening in the TV cabinet.
Insert the hooks inside the
TV cabinet opening.
Lamp unit door
10
Plug in the power cord and turn on the TV. After the initial warmup period (which may take several seconds for full picture brightness), the TV should operate normally. If any of the following conditions exist, turn off the TV, unplug the power cord, and repeat steps 1–9 to ensure that the lamp unit and lamp unit door are installed correctly:
• No picture
• Dark picture
• TV will not turn on
If, after repeating steps 1–9, the problem still exists:
•
In the U.S., call TACP consumer solutions at 1-800-
631-3811.
•
In Canada, locate the nearest Toshiba authorized service depot by directing your web browser to www.toshiba.ca; click “Home Entertainment,” and then click “Support.”
Disposing of the used lamp unit
•
•
Place the used lamp unit in the empty box from the new unit.
Keep the lamp unit out of reach of children and pets.
CAUTION: Always handle the lamp unit with care.
The lamp unit in this TV was designed for safe replacement by consumers; however, if the lamp unit is subjected to intentional or accidental abuse (such as excessive mechanical abuse or handling by children or pets), the unit may break, exposing sharp edges or pinch points.
•
Dispose of the used lamp unit by the approved method for your area.
NOTE :
The lamp unit contains mercury.
Disposal of mercury may be regulated due to environmental considerations. For disposal or recycling information, contact your local authorities or the Electronic Industries Alliance
(www.eiae.org).
49
HM66 (E/F) Web 213:276
HM66_EN.book Page 50 Thursday, February 23, 2006 2:49 PM
Chapter 8: Appendix
Specifications
Notes:
• This model complies with the specifications listed
below.
• Designs and specifications are subject to change
without notice.
• This model may not be compatible with features and/or
specifications that may be added in the future.
Television System
NTSC standard
ATSC standard (8VSB)
Digital Cable (64 QAM, 256 QAM; in-the-clear, unencrypted*)
Channel Coverage
VHF: 2 through 13
UHF: 14 through 69
Cable TV: Mid band (A-8 through A-1, A through I)
Super band (J through W)
Hyper band (AA through ZZ, AAA, BBB)
Ultra band (65 through 94, 100 through 135)
Power Source
120 V AC, 60 Hz
Power Consumption
215 W (average)
28 W in standby mode (using a CableCARD™)
24 W in standby mode (without a CableCARD™)
Audio Power
10 W + 10 W
Speaker Type
Main: Two 2-3/8 × 4-3/4 inches (6×12 cm) round
Tweeter: Two 1-5/16 inches (33 mm) round
Video/Audio Terminals
S-VIDEO INPUT:
Y: 1 V(p-p), 75 ohm, negative sync.
C: 0.286 V(p-p) (burst signal), 75 ohm
VIDEO/AUDIO INPUT:
VIDEO: 1 V(p-p), 75 ohm, negative sync.
AUDIO: 150 mV(rms) (30% modulation equivalent, 22 k ohm or greater)
ColorStream
®
(component video) HD INPUT:
VIDEO:Y: 1V(p-p), 75 ohm
P
R
: 0.7 V(p-p), 75 ohm
P
B
: 0.7 V(p-p), 75 ohm
Suggested formats: 1080i, 480p, 480i, 720p
AUDIO: 150 mV(rms), 22 k ohm or greater
HDMI™ INPUT:
HDMI compliant (type A connector)
HDCP compliant
E-EDID
**
compliant
Suggested formats: 1080i, 480p, 480i, 720p
HDMI Audio: 2-channel PCM; 32/44.1/48 kHz sampling frequency; 16/20/24 bits per sample
VIDEO/AUDIO OUTPUT (also for recording):
VIDEO: 1 V(p-p), 75 ohm, negative sync.
AUDIO: 150 mV(rms) (30% modulation equivalent,
2.2 k ohm or less)
VARIABLE AUDIO OUTPUT:
0–300 mV(rms) (30% modulation equivalent, 2.2 k ohm or less)
DIGITAL AUDIO OUTPUT:
Optical type
Dimensions
50HM66: Width: 47-3/16 inches (1,199 mm)
Height: 30-11/16 inches (780 mm)
Depth: 16-5/8 inches (422 mm)
56HM66: Width: 52-3/8 inches (1,330 mm)
Height: 33-3/4 inches (857 mm)
Depth: 18-3/8 inches (467 mm)
Weight
50HM66:64 lbs (29.0 kg)
56HM66:72 lbs (32.7 kg)
Operating conditions
Temperature: 41ºF–95ºF (5ºC–35ºC)
Humidity: 20–80% (no moisture condition)
Supplied Accessories
• Remote control with two size “AAA” batteries
• Dual-wand IR blaster cable
• Installation Guide
• Operating Guide (this book)
Optional Stands
50HM66:ST 5066
56HM66:ST 5666
* Encrypted channels can be viewed on this TV using a
CableCARD.™ (
- Installation Guide).
** E-EDID = Enhanced-Extended Display Identification
50
HM66 (E/F) Web 213:276
HM66_EN.book Page 51 Thursday, February 23, 2006 2:49 PM
Chapter 8: Appendix
Limited United States Warranty for DLP™ Television Models
Toshiba America Consumer Products, L.L.C. (“TACP”) makes the following limited warranties to original consumers in the United States.
THESE LIMITED WARRANTIES EXTEND TO THE ORIGINAL
CONSUMER PURCHASER OR ANY PERSON RECEIVING THIS DLP™
TELEVISION AS A GIFT FROM THE ORIGINAL CONSUMER
PURCHASER AND TO NO OTHER PURCHASER OR TRANSFEREE.
DLP™ TELEVISIONS PURCHASED IN THE U.S.A. AND USED
ANYWHERE OUTSIDE OF THE U.S.A., INCLUDING, WITHOUT
LIMITATION, CANADA AND MEXICO, ARE NOT COVERED BY THESE
WARRANTIES.
DLP™ TELEVISIONS PURCHASED ANYWHERE OUTSIDE OF THE
U.S.A., INCLUDING, WITHOUT LIMITATION, CANADA AND MEXICO,
AND USED IN THE U.S.A., ARE NOT COVERED BY THESE
WARRANTIES.
Limited One (1) Year Warranty on Parts and Labor
TACP warrants this DLP™ Television and its parts against defects in materials or workmanship for a period of one (1) year after the date of original retail purchase. DURING THIS PERIOD, TACP WILL, AT TACP’S
OPTION, REPAIR OR REPLACE A DEFECTIVE PART WITH A NEW OR
REFURBISHED PART WITHOUT CHARGE TO YOU FOR PARTS OR
LABOR. During this period, TACP Authorized Service Station personnel will come to your home when warranty service is required. Depending on the type of repair required, the service will either be performed in your home or the DLP™ Television will be taken to a TACP Authorized Service
Station for repair and returned to your home at no cost to you.
Limited One (1) Year Warranty on Lamp Unit
TACP warrants the original lamp unit contained in this DLP™ Television against defects in materials or workmanship for a period of one (1) year after the date of original retail purchase. DURING THIS PERIOD, TACP
WILL, AT TACP’S OPTION, EXCHANGE A DEFECTIVE LAMP UNIT
WITH A NEW OR REFURBISHED LAMP UNIT WITHOUT CHARGE TO
YOU. LABOR CHARGES FOR LAMP UNIT REPLACEMENT ARE YOUR
RESPONSIBILITY AND ARE NOT COVERED UNDER THIS
WARRANTY. The lamp unit is a user-replaceable component.
Rental Units
The warranty for DLP™ Television rental units begins on the date of the first rental or thirty (30) days after the date of shipment to the rental firm, whichever comes first.
Limited Warranty for Commercial Units
TACP warrants DLP™ Televisions, including the lamp units contained therein, that are sold and used for commercial purposes as follows: all parts are warranted against defects in materials or workmanship for a period of ninety (90) days after the date of original retail purchase.
DURING THIS PERIOD, TACP WILL, AT TACP’S OPTION, REPAIR OR
REPLACE A DEFECTIVE PART WITH A NEW OR REFURBISHED PART
WITHOUT CHARGE TO YOU.
Owner’s Manual and Product Registration
Read this owner’s manual thoroughly before operating this DLP™ television.
Complete and mail the enclosed product registration card or register your
DLP™ Television online at www.tacp.toshiba.com/service as soon as possible. By registering your DLP™ Television you will enable TACP to bring you new products specifically designed to meet your needs and help us to contact you in the unlikely event a safety notification is required under the Consumer Product Safety Act. Failure to register your product does not diminish your warranty rights.
Your Responsibility
THE ABOVE WARRANTIES ARE SUBJECT TO THE FOLLOWING
CONDITIONS:
(1) You must retain your original bill of sale or provide other proof of purchase.
(2) All warranty servicing of this DLP™ Television must be performed by an Authorized TACP Service Station.
(3) The warranties from TACP are effective only if this DLP™ Television is purchased and operated in the Continental U.S.A. or Puerto Rico.
(4) Labor service charges for set installation, setup, adjustment of customer controls, and installation or repair of antenna systems are not covered by this warranty. Reception problems caused by inadequate antenna systems, misaligned satellite dishes, cable television distribution, VCRs, DVD players/recorders, personal computer level IEEE1394 devices, and any other connected signal source device are your responsibility.
(5) Warranties extend only to defects in materials or workmanship as limited above, and do not extend to any DLP™ Television or parts that have been lost or discarded by you or to damage to the DLP™
Television or parts caused by fires, misuse, accident, Acts of God
(such as lightning or fluctuations in electric power), improper installation, improper maintenance, or use in violation of instructions furnished by TACP; use or malfunction through simultaneous use of this DLP™ Television and connected equipment; or to units that have been modified or had the serial number removed, altered, defaced, or rendered illegible.
How to Obtain Warranty Service
If, after following all of the operating instructions in this manual and reviewing the section titled “Troubleshooting,” you find that service is needed:
(1) To find the nearest TACP Authorized Service Station, visit TACP’s website at www.tacp.toshiba.com/service or contact TACP’s
Consumer Solution Center toll free at 1-800-631-3811.
(2) You must present your original bill of sale or other proof of purchase to the TACP Authorized Service Station.
For additional information, visit TACP’s web site: www.tacp.toshiba.com.
ALL WARRANTIES IMPLIED BY THE LAW OF ANY STATE OF THE
U.S.A., INCLUDING THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE,
ARE EXPRESSLY LIMITED TO THE DURATION OF THE LIMITED
WARRANTIES SET FORTH ABOVE. WITH THE EXCEPTION OF ANY
WARRANTIES IMPLIED BY THE LAW OF ANY STATE OF THE U.S.A.
AS HEREBY LIMITED, THE FOREGOING WARRANTY IS EXCLUSIVE
AND IN LIEU OF ALL OTHER WARRANTIES, GUARANTEES,
AGREEMENTS, AND SIMILAR OBLIGATIONS OF TACP WITH
RESPECT TO THE REPAIR OR REPLACEMENT OF ANY PARTS. IN NO
EVENT SHALL TACP BE LIABLE FOR CONSEQUENTIAL OR
INCIDENTAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, LOST
PROFITS, BUSINESS INTERRUPTION, OR MODIFICATION OR
ERASURE OF RECORDED DATA CAUSED BY USE, MISUSE OR
INABILITY TO USE THIS DLP™ TELEVISION).
No person, agent, distributor, dealer, or company is authorized to change, modify, or extend the terms of these warranties in any manner whatsoever.
The time within which an action must be commenced to enforce any obligation of TACP arising under the warranty or under any statute or law of the United States or any state thereof is hereby limited to ninety (90) days from the date you discover, or should have discovered, the defect.
This limitation does not apply to implied warranties arising under the law of any state of the U.S.A.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU
MAY ALSO HAVE OTHER RIGHTS WHICH MAY VARY FROM STATE
TO STATE IN THE U.S.A. SOME STATES OF THE U.S.A. DO NOT
ALLOW LIMITATIONS ON THE DURATION OF AN IMPLIED
WARRANTY, WHEN AN ACTION MAY BE BROUGHT, OR THE
EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL
DAMAGES. THEREFORE, THE ABOVE PROVISIONS MAY NOT APPLY
TO YOU UNDER SUCH CIRCUMSTANCES. 05
51
HM66 (E/F) Web 213:276
HM66_EN.book Page 52 Thursday, February 23, 2006 2:49 PM
Chapter 8: Appendix
Limited Canada Warranty for DLP™ Television Models
Toshiba of Canada Limited (“TCL”) makes the following limited warranties to original consumers in Canada.
THESE LIMITED WARRANTIES EXTEND TO THE ORIGINAL
CONSUMER PURCHASER OR ANY PERSON RECEIVING THIS DLP™
TELEVISION AS A GIFT FROM THE ORIGINAL CONSUMER
PURCHASER AND TO NO OTHER PURCHASER OR TRANSFEREE.
PRODUCTS PURCHASED IN THE U.S.A. AND USED IN CANADA ARE
NOT COVERED BY THESE WARRANTIES.
PRODUCTS PURCHASED IN CANADA AND USED IN THE U.S.A. ARE
NOT COVERED BY THESE WARRANTIES.
Limited One (1) Year Warranty on Parts and Labor*
TCL warrants this DLP™ television television and its parts against defects in materials or workmanship for a period of one (1) year after the date of original retail purchase. DURING THIS PERIOD, TCL WILL, AT TCL’S
OPTION, REPAIR OR REPLACE A DEFECTIVE PART WITH A NEW OR
REFURBISHED PART WITHOUT CHARGE TO YOU FOR PARTS OR
LABOR. TCL Authorized Service Depot personnel will come to your home when warranty service is required. Depending on the type of repair required, either the service will be performed in your home or the set will be taken to the TCL Authorized Service Depot for repair and returned to your home at no cost to you. IN-HOME SERVICE ONLY APPLIES WITHIN
100 KILOMETERS OF AN AUTHORIZED TCL SERVICE DEPOT.
Limited One (1) Year Warranty on Lamp Unit*
TCL warrants the lamp unit in this DLP™ television against defects in materials or workmanship for a period of one (1) year after the date of original retail purchase. DURING THIS PERIOD, TCL WILL, AT TCL’S
OPTION, EXCHANGE A DEFECTIVE LAMP UNIT WITH A NEW OR
REFURBISHED LAMP UNIT WITHOUT CHARGE TO YOU. LABOR
CHARGES FOR LAMP UNIT REPLACEMENT ARE NOT COVERED
UNDER WARRANTY. The lamp unit is a user-replaceable component.
Rental Units
The warranty for rental units, including the lamp units contained therein, begins with the date of first rental or thirty (30) days from the date of shipment to the rental firm, whichever comes first.
*Limited Warranty for Commercial Units
TCL warrants DLP™ televisions, including the lamp units contained therein, sold and used for commercial purposes as follows: all parts are warranted against defects in materials or workmanship for a period of ninety (90) days after the date of original purchase. DURING THIS
PERIOD, TCL WILL, AT TCL’S OPTION, REPAIR OR REPLACE A
DEFECTIVE PART WITH A NEW OR REFURBISHED PART WITHOUT
CHARGE TO YOU. ON-SITE SERVICE ONLY APPLIES WITHIN 100
KILOMETERS OF AN AUTHORIZED TCL SERVICE DEPOT.
Owner’s Manual and Product Registration
Read this owner’s manual thoroughly before operating this DLP™ television.
Register your product online at www.toshiba.ca as soon as possible.
By registering your product you will enable TCL bring you new products specifically designed to meet your needs and help us to contact you in the unlikely event a safety notification is required under the Consumer
Product Safety Act. Failure to register your product does not diminish your warranty rights.
Your Responsibility
THE ABOVE WARRANTIES ARE SUBJECT TO THE FOLLOWING
CONDITIONS:
(1) You must provide your bill of sale or other proof of purchase.
(2) All warranty servicing of this DLP™ television must be performed by an Authorized TCL Service Depot.
(3) These warranties from TCL are effective only if the DLP™ television is purchased in Canada from an authorized TCL dealer and operated in
Canada.
(4) Labor charges for installation, setup, adjustment of customer controls, and installation or repair of antenna systems are not covered by these warranties. Reception problems caused by inadequate antenna systems are your responsibility.
(5) Warranties extend only to defects in materials or workmanship as limited above, and do not extend to any DLP™ television or parts that have been lost or discarded by you or to damage to the television or parts caused by fires, misuse, accident, Acts of God (such as lightning or fluctuations in electric power), improper installation, improper maintenance, or use in violation of instructions furnished by
TCL; use or malfunction through simultaneous use of this product and connected equipment; or to units that have been modified or had the serial number removed, altered, defaced, or rendered illegible.
How to Obtain Warranty Services
If, after following all of the operating instructions in this manual and checking the “Troubleshooting” section, you find that service is needed:
(1) To find the nearest TCL Authorized Service Depot, visit TCL’s web site at www.toshiba.ca.
(2) Present your bill of sale or other proof of purchase to the Authorized
Service Depot.
For additional information, visit TCL’s web site: www.toshiba.ca
ALL WARRANTIES IMPLIED BY THE LAW OF ANY PROVINCE OF
CANADA, INCLUDING THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE,
ARE EXPRESSLY LIMITED TO THE DURATION OF THE LIMITED
WARRANTIES SET FORTH ABOVE. WITH THE EXCEPTION OF ANY
WARRANTIES IMPLIED BY THE LAW OF ANY PROVINCE OF CANADA
AS HEREBY LIMITED, THE FOREGOING WARRANTY IS EXCLUSIVE
AND IN LIEU OF ALL OTHER WARRANTIES, GUARANTEES,
AGREEMENTS, AND SIMILAR OBLIGATIONS OF TCL WITH RESPECT
TO THE REPAIR OR REPLACEMENT OF ANY PARTS. IN NO EVENT
SHALL TCL BE LIABLE FOR CONSEQUENTIAL OR INCIDENTAL
DAMAGES (INCLUDING, BUT NOT LIMITED TO, LOST PROFITS,
BUSINESS INTERRUPTION, OR MODIFICATION OR ERASURE OF
RECORDED DATA CAUSED BY USE, MISUSE, OR INABILITY TO USE
THIS PRODUCT).
No person, agent, distributor, dealer, or company is authorized to change, modify, or extend the terms of these warranties in any manner whatsoever.
The time within which action must be commenced to enforce any obligation of TCL arising under this warranty or under any law of Canada or of any province thereof is hereby limited to 90 days from the date you discover, or should have discovered, the defect. This limitation does not apply to implied warranties arising under the law of any province of
Canada.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU
MAY ALSO HAVE OTHER RIGHTS, WHICH MAY VARY FROM
PROVINCE TO PROVINCE IN CANADA. SOME PROVINCES OF
CANADA DO NOT ALLOW LIMITATIONS ON THE DURATION OF AN
IMPLIED WARRANTY, LIMITATIONS ON THE TIME WITHIN WHICH AN
ACTION MAY BE BROUGHT, OR THE EXCLUSION OR LIMITATION OF
INCIDENTAL OR CONSEQUENTIAL DAMAGES; THEREFORE, THE
ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU
UNDER SUCH CIRCUMSTANCES.
52
HM66 (E/F) Web 213:276
HM66_EN.book Page 53 Thursday, February 23, 2006 2:49 PM
Chapter 8: Appendix
A copy of the GPL source code in this product may be obtained by contacting Toshiba Consumer Solutions at (800)631-3811. There will be a charge to cover the costs of providing the source code.
A copy of the LGPL source code in this product may be obtained by contacting Toshiba Consumer Solutions at (800)631-3811. There will be a charge to cover the costs of providing the source code.
USB Protocol Copyright © 2005 The NetBSD Foundation, Inc. All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:
(1) Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
(2) Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
(3) Neither the name of The NetBSD Foundation nor the names of its contributors may be used to endorse or promote products derived from this software without specified prior written permission.
THIS SOFTWARE IS PROVIDED BY THE NETBSD FOUNDATION, INC.
AND CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED
WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL
THE FOUNDATION OR CONTRIBUTORS BE LIABLE FOR ANY
DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE
OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH
DAMAGE.
This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit (http://www.openssl.org).
This product includes cryptographic software written by Eric Young
OpenSSL 0.9.7d Copyright © 1998-2000 the OpenSSL Project. All Rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:
(1) Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
(2) Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
(3) All advertising materials mentioning features or use of this software must display the following acknowledgement: This product includes software developed by the OpenSSL Project for use in the OpenSSL
Toolkit (http://openssl.org).
(4) The names “OpenSSL Toolkit” and “Open SSL Project” must not be used to endorse or promote products derived from this software without prior written permission. For written permission, please contact [email protected].
(5) Products derived from this software may not be called “OpenSSL” nor may “Open SSL” appear in their names without prior written permission of the OpenSSL Project.
(6) Redistributions of any form whatsoever must retain the following acknowledgement: “This product includes software developed by the
OpenSSL Project for use in the OpenSSL Toolkit (http:// www.openssl.org).”
THIS SOFTWARE IS PROVIDED BY THE OpenSSL PROJECT “AS IS”
AND ANY EXPRESSED OR IMPLIED WARRANTIES, INCLUDING, BUT
NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
ARE DISCLAIMED. IN NO EVENT SHALL THE OpenSSL PROJECT OR
CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR
PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN
IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. This product includes cryptographic software written by Eric Young
([email protected]). This product includes software written by Tim
Hudson ([email protected]).
Copyright © 1995-1998 Eric Young ([email protected]). All Rights reserved. This package is an SSL implementation written by Eric Young
([email protected]). The implementation was written so as to conform with Netscapes SSL. This library is free for commercial and noncommercial use so long as the following conditions are adhered to. The following conditions apply to all code found in this distribution, be it the
RC4, RSA, Ihash, DES, etc., code; not just the SSL code. The SSL documentation included with this distribution is covered by the same copyright terms except that the holder is Tim Hudson ([email protected]).
Copyright remains Eric Young’s, and as such any Copyright notices in the code are not to be removed. If this package is used in a product, Eric
Young should be given attribution as the author of the parts of the library used. This can be in the form of a textual message at program startup or in documentation (online or textual) provided with the package.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:
(1) Redistributions of source code must retain the copyright notice, this list of conditions and the following disclaimer.
(2) Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
(3) All advertising materials mentioning features or use of this software must display the following acknowledgement: “This product includes cryptographic software written by Eric Young ([email protected]).”
The word ‘cryptographic’ can be left out if the routines from the library being used are not cryptographic related.
(4) If you include any Windows specific code (or derivative thereof) from the apps directory (application code) you must include an acknowledgement: “This product includes software written by Tim
Hudson ([email protected]).”
THIS SOFTWARE IS PROVIDED BY ERIC YOUNG “AS IS” AND ANY
EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED
TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO
EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR
ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE
OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH
DAMAGE. The license and distribution terms for any publicly available version or derivative of this code cannot be changed, i.e. this code cannot simply be copied and put under another distribution license (including the
GNU Public License).
53
HM66 (E/F) Web 213:276
HM66_EN.book Page 54 Thursday, February 23, 2006 2:49 PM
Index
A
Antenna input configuration ............ 16
Audio quality adjustments
............... 33
Auto aspect .................................... 29
Auto power off
................................ 40
B
Back of the TV
.................................. 6
Blocking channels .......................... 37
C
CableClear DNR ............................ 41
CH RTN button
............................... 26
CH
U u
buttons..............................
26
Channel Browser Setup
.................. 24
Channel Browser™ ........................ 24
Channel Browser™ banner
............. 25
Channel Number buttons ................ 26
Channel programming
Automatic programming
........... 17
Manually adding and deleting ... 17
Cinema mode ................................. 29
Closed captions
.............................. 31
Color temperature .......................... 42
ColorStream HD audio
.................... 20
D
Defaults, restore TV factory
............ 22
Digital audio selector ...................... 32
Digital signal meter
......................... 21
DNR (Digital Noise Reduction) ........ 41
Dynamic contrast
............................ 41
F
Favorite channels
........................... 18
Features, TV .................................... 4
Front of the TV
................................. 5
H
HDMI audio mode
.......................... 20
I
INPUT button
................................. 23
Installation, setup ............................. 4
Integrated digital tuning
.................... 4
L
Labeling video input ........................ 23
Lamp mode
.................................... 42
Lamp unit replacement .................... 47
Language selection
......................... 16
Last mode memory feature ............. 40
LED indications
............................... 46
LOCKS menu
Channels, blocking ................... 37
Enable rating blocking
.............. 36
New PIN code .......................... 35
Panel lock
................................ 39
Unlocking programs temporarily
................. 38
Video inputs, locking ................ 38
Locks menu .................................... 35
M
MPEG noise reduction .................... 41
MTS feature
................................... 33
MUTE button .................................. 32
O
Optical audio output format ............. 34
P
Picture adjustment .......................... 30
Picture mode
.................................. 30
Picture quality ................................. 30
Picture scroll
................................... 28
Picture size selection ...................... 27
POWER button
................................. 5
Q
Quick Restart™
.............................. 20
R
RECALL button
.............................. 40
Remote control
Battery installation ...................... 7
Device code table
.................... 12
Effective range ........................... 7
Functional key chart
................. 10
Learning about the buttons ......... 8
Programming
........................... 11
S
SAP sound .....................................33
Scroll settings
.................................28
Selecting Menu Language ...............16
Side panel control
.............................5
Sleep timer .....................................39
Speaker On/Off
...............................34
Specifications .................................50
StableSound
®
.................................34
Stereo sound ..................................33
SurfLock™
......................................26
System status .................................22
T
TheaterWide
®
picture size ...............27
Troubleshooting
..............................44
V
V-Chip blocking (Locks menu)
.........35
Video input label .............................23
Video input lock
..............................38
W
Warranty
Canada
....................................52
U.S.
.........................................51
WOW:SRS 3D ................................43
WOW:SRS Focus
...........................43
WOW:SRS TruBass ........................43
54
HM66 (E/F) Web 213:276
HM66_EN.book Page 55 Thursday, February 23, 2006 2:49 PM
Notes
55
HM66 (E/F) Web 213:276
HM66_EN.book Page 56 Thursday, February 23, 2006 2:49 PM
Corporate Headquarters: 82 TOTOWA ROAD, WAYNE, NJ 07470, U.S.A.
NATIONAL SERVICE DIVISION: 1420-B TOSHIBA DRIVE, LEBANON, TN 37087, U.S.A.
HEAD OFFICE: 191 McNABB STREET, MARKHAM, ONTARIO, L3R 8H2, CANADA – TEL: (905) 470-5400
SERVICE CENTERS:
TORONTO: 191 McNABB STREET, MARKHAM, ONTARIO L3R 8H2, CANADA – TEL: (905) 470- 5400
MONTREAL: 18050 TRANS CANADA, KIRKLAND, QUEBEC, H9J 4A1, CANADA – TEL: (514) 390-7766
VANCOUVER: 22171 FRASERWOOD WAY, RICHMOND, B.C., V6W 1J5, CANADA – TEL: (604) 303-2500
MANUFACTURED BY
CableClear, ColorStream, StableSound, and TheaterWide are registered trademarks of Toshiba America Consumer Products, L.L.C.
Channel Browser, SurfLock, and Quick Restart are trademarks of Toshiba America Consumer Products, L.L.C.
Digital Light Processing™, DLP™ and the DLP™ medallion are trademarks of Texas Instruments.
PRINTED IN USA
(06-03)
HM66 (E/F) Web 213:276
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 4 Chapter 1: Introduction
- 4 Features of your new TV
- 4 your new TV
- 5 TV front and side panel controls and connections
- 6 TV back panel connections
- 7 Chapter 2: Using the remote control
- 7 Preparing the remote control for use
- 7 Installing the remote control batteries
- 7 Remote control effective range
- 8 Learning about the remote control
- 9 Using the remote control to control your other devices
- 10 Remote Control functional key chart
- 11 devices
- 12 Remote control codes
- 14 Chapter 3: Menu layout and navigation
- 14 Main menu layout
- 15 Setup/Installation menu layout
- 15 Navigating the menu system
- 16 Chapter 4: Setting up your TV
- 16 Selecting the menu language
- 16 and ANT 2 terminals
- 17 Programming channels into the TV’s channel memory
- 17 Programming channels automatically
- 17 memory
- 18 Programming your favorite channels
- 20 Setting the ColorStream HD audio mode
- 20 Setting the HDMI™ audio mode
- 20 Viewing the CableCARD™ menu
- 20 Setting the Quick Restart™ feature
- 21 Viewing the digital signal meter
- 22 Viewing the system status
- 23 Chapter 5: Using the TV’s basic features
- 23 Selecting the video input source to view
- 23 Labeling the video input sources
- 24 Tuning channels
- 24 Using the Channel Browser
- 26 Tuning your favorite channels
- 26 Tuning to the next programmed channel
- 26 unprogrammed)
- 26 Return
- 26 Switching between two channels using SurfLock
- 27 Selecting the picture size
- 28 and 3 only)
- 29 Using the auto aspect ratio feature
- 29 (480i signals only)
- 30 Adjusting the picture
- 30 Selecting the picture mode
- 30 Adjusting the picture quality
- 31 Using the closed caption mode
- 31 Closed Caption Advanced
- 32 Digital closed captions
- 32 Adjusting the audio
- 32 Muting the sound
- 32 Using the digital audio selector
- 33 Selecting stereo/SAP broadcasts
- 33 Adjusting the audio quality
- 34 feature
- 34 Turning off the built-in speakers
- 34 Selecting the optical audio output format
- 35 Using the Locks menu
- 35 Entering the PIN code
- 35 If you cannot remember your PIN code
- 35 Changing your PIN code
- 36 by rating (V-Chip)
- 37 Blocking channels
- 38 Unlocking programs temporarily
- 38 Using the input lock feature
- 39 Using the control panel lock feature
- 39 Setting the sleep timer
- 40 RECALL
- 40 Understanding the auto power off feature
- 40 Understanding the last mode memory feature
- 41 Chapter 6: Using the TV’s advanced features
- 41 Using the advanced picture settings features
- 41 Using dynamic contrast
- 41 /DNR (digital noise reduction)
- 41 Using MPEG noise reduction
- 42 Selecting the color temperature
- 42 Selecting the lamp mode
- 43 Using the Game Mode feature
- 43 Using the advanced audio settings features
- 43 Using the SRS WOW™ surround sound feature
- 44 Chapter 7: Troubleshooting
- 44 General troubleshooting
- 46 LED indications
- 47 Chapter 8: Appendix
- 47 Lamp unit replacement and care
- 47 (User-replaceable component)
- 47 When to replace the lamp unit
- 48 How to replace the lamp unit
- 49 Disposing of the used lamp unit
- 50 Specifications
- 51 for DLP™ Television Models
- 54 Index
- 48 HM66 (E/F) Web