Toshiba ES4 Answering Machine User Manual

Telecommunication Systems Division
®
Voice Processing Systems
Stratagy iES32, ES4, ES80,
ES96, ES96R
User Guide
January 2003
Publication Information
Toshiba America Information Systems, Inc., Telecommunication
Systems Division, reserves the right, without prior notice, to revise
this information publication for any reason, including, but not limited
to, utilization of new advances in the state of technical arts or to
simply change the design of this document.
Further, Toshiba America Information Systems, Inc.,
Telecommunication Systems Division, also reserves the right,
without prior notice, to make such changes in equipment design or
components as engineering or manufacturing methods may warrant.
© Copyright 2003
Toshiba America Information Systems, Inc.
Telecommunication Systems Division
All rights reserved. No part of this manual, covered by the copyrights
hereon, may be reproduced in any form or by any means—graphic,
electronic, or mechanical, including recording, taping, photocopying,
or information retrieval systems—without express written permission
of the publisher of this material.
Strata is a registered trademark of Toshiba Corporation.
STG-UG-ESALL-VB
4016230
Stratagy and Perception are registered trademarks of Toshiba
America Information Systems, Inc.
Version B, January 2003
Trademarks, registered trademarks, and service marks are the
property of their respective owners.
TOSHIBA AMERICA INFORMATION SYSTEMS, INC. (“TAIS”)
Telecommunication Systems Division License Agreement
IMPORTANT: THIS LICENSE AGREEMENT (“AGREEMENT”) IS A LEGAL AGREEMENT BETWEEN YOU (“YOU”) AND TAIS. CAREFULLY READ THIS LICENSE AGREEMENT. USE OF ANY
SOFTWARE OR ANY RELATED INFORMATION (COLLECTIVELY, “SOFTWARE”) INSTALLED ON OR SHIPPED WITH A TAIS TELECOMMUNICATION SYSTEM PRODUCT OR OTHERWISE MADE
AVAILABLE TO YOU BY TAIS IN WHATEVER FORM OR MEDIA, WILL CONSTITUTE YOUR ACCEPTANCE OF THESE TERMS, UNLESS SEPARATE TERMS ARE PROVIDED BY THE SOFTWARE
SUPPLIER. IF YOU DO NOT AGREE WITH THE TERMS OF THIS LICENSE AGREEMENT, DO NOT INSTALL, COPY OR USE THE SOFTWARE AND PROMPTLY RETURN IT TO THE LOCATION
FROM WHICH YOU OBTAINED IT IN ACCORDANCE WITH APPLICABLE RETURN POLICIES. EXCEPT AS OTHERWISE AUTHORIZED IN WRITING BY TAIS, THIS SOFTWARE IS LICENSED FOR
DISTRIBUTION ONLY TO END-USERS PURSUANT TO THIS LICENSE AGREEMENT.
1. License Grant. The Software is not sold; it is licensed upon payment of applicable charges. TAIS grants to you a personal, non-transferable and non-exclusive right to use the copy of the Software
provided under this License Agreement. You agree you will not copy the Software except as necessary to use it on one TAIS system at a time at one location. Modifying, translating, renting, copying,
distributing, transferring or assigning all or part of the Software, or any rights granted hereunder, to any other persons and removing any proprietary notices, labels or marks from the Software is strictly
prohibited; You agree violation of such restrictions will cause irreparable harm to TAIS and provide grounds for injunctive relief, without notice, against You or any other person in possession of the Software.
You and any other person whose possession of the software violates this License Agreement shall promptly surrender possession of the Software to TAIS, upon demand. Furthermore, you hereby agree not
to create derivative works based on the Software. TAIS reserves the right to terminate this license and to immediately repossess the software in the event that You or any other person violates this License
Agreement.
2. Intellectual Property. You acknowledge that no title to the intellectual property in the Software is transferred to you. You further acknowledge that title and full ownership rights to the Software will remain
the exclusive property of TAIS and/or its suppliers, and you will not acquire any rights to the Software, except the license expressly set forth above. You will not remove or change any proprietary notices
contained in or on the Software. The Software is protected under US patent, copyright, trade secret, and/or other proprietary laws, as well as international treaties. Any transfer, use, or copying of the
software in violation of the License Agreement constitutes copyright infringement. You are hereby on notice that any transfer, use, or copying of the Software in violation of this License Agreement constitutes
a willful infringement of copyright.
3. No Reverse Engineering. You agree that you will not attempt, and if you employ employees or engage contractors, you will use your best efforts to prevent your employees and contractors from
attempting to reverse compile, reverse engineer, modify, translate or disassemble the Software in whole or in part. Any failure to comply with the above or any other terms and conditions contained herein will
result in the automatic termination of this license and the reversion of the rights granted hereunder back to TAIS.
4. Limited Warranty. THE SOFTWARE IS PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND. TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, TAIS AND ITS SUPPLIERS
DISCLAIM ALL WARRANTIES WITH REGARD TO THE SOFTWARE, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE WARRANTY OF NON-INFRINGEMENT OF THIRD
PARTY RIGHTS, THE WARRANTY OF YEAR 2000 COMPLIANCE, AND THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS
TO THE QUALITY AND PERFORMANCE OF THE SOFTWARE IS WITH YOU. NEITHER TAIS NOR ITS SUPPLIERS WARRANT THAT THE FUNCTIONS CONTAINED IN THE SOFTWARE WILL MEET
YOUR REQUIREMENTS OR THAT THE OPERATION OF THE SOFTWARE WILL BE UNINTERRUPTED OR ERROR-FREE. HOWEVER, TAIS WARRANTS THAT ANY MEDIA ON WHICH THE
SOFTWARE IS FURNISHED IS FREE FROM DEFECTS IN MATERIAL AND WORKMANSHIP UNDER NORMAL USE FOR A PERIOD OF NINETY (90) DAYS FROM THE DATE OF DELIVERY TO YOU.
5. Limitation Of Liability. TAIS’ ENTIRE LIABILITY AND YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LICENSE AGREEMENT SHALL BE AT TAIS’ OPTION REPLACEMENT OF THE MEDIA OR
REFUND OF THE PRICE PAID. TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, IN NO EVENT SHALL TAIS OR ITS SUPPLIERS BE LIABLE TO YOU FOR ANY CONSEQUENTIAL,
SPECIAL, INCIDENTAL OR INDIRECT DAMAGES FOR PERSONAL INJURY, LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, LOSS OF BUSINESS INFORMATION/DATA, OR ANY
OTHER PECUNIARY LOSS OF ANY KIND ARISING OUT OF THE USE OR INABILITY TO USE THE SOFTWARE, EVEN IF TAIS OR ITS SUPPLIER HAS BEEN ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES. IN NO EVENT SHALL TAIS OR ITS SUPPLIERS BE LIABLE FOR ANY CLAIM BY A THIRD PARTY.
6. State/Jurisdiction Laws. SOME STATES/JURISDICTIONS DO NOT ALLOW THE EXCLUSION OF IMPLIED WARRANTIES OR LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY MAY LAST, OR
THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO SUCH LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU. THIS LIMITED WARRANTY GIVES YOU
SPECIFIC RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE/JURISDICTION TO STATE/JURISDICTION.
7. Export Laws. This License Agreement involves products and/or technical data that may be controlled under the United States Export Administration Regulations and may be subject to the approval of the
United States Department of Commerce prior to export. Any export, directly or indirectly, in contravention of the United States Export Administration Regulations, or any other applicable law, regulation or
order, is prohibited.
8. Governing Law. This License Agreement will be governed by the laws of the State of California, United States of America, excluding its conflict of law provisions.
9. United States Government Restricted Rights. The Software is provided with Restricted Rights. Use, duplication, or disclosure by the United States Government, its agencies and/or instrumentalities is
subject to restrictions as set forth in subparagraph (c)(1)(ii) of The Rights in Technical Data and Computer Software Clause at DFARS 252.227-7013 (October 1988) or subparagraphs (c)(1) and (2) of the
Commercial Computer Software - Restricted Rights at 48 CFR 52.227-19, as applicable.
10. Severability. If any provision of this License Agreement shall be held to be invalid, illegal or unenforceable, the validity, legality and enforceability of the remaining provisions hereof shall not in any way be
affected or impaired.
11. No Waiver. No waiver of any breach of any provision of this License Agreement shall constitute a waiver of any prior, concurrent or subsequent breach of the same or any other provisions hereof, and no
waiver shall be effective unless made in writing and signed by an authorized representative of the waiving party.
YOU ACKNOWLEDGE THAT YOU HAVE READ THIS LICENSE AGREEMENT AND THAT YOU UNDERSTAND ITS PROVISIONS. YOU AGREE TO BE BOUND BY ITS TERMS AND CONDITIONS. YOU
FURTHER AGREE THAT THIS LICENSE AGREEMENT CONTAINS THE COMPLETE AND EXCLUSIVE AGREEMENT BETWEEN YOU AND TAIS AND SUPERSEDES ANY PROPOSAL OR PRIOR
AGREEMENT, ORAL OR WRITTEN, OR ANY OTHER COMMUNICATION RELATING TO THE SUBJECT MATTER OF THIS LICENSE AGREEMENT.
Toshiba America Information Systems, Inc.
Telecommunication Systems Division
9740 Irvine Boulevard
Irvine, California 92618-1697
United States of America
TSD 081601
5932
Toshiba America Information Systems, Inc.
Telecommunication Systems Division
Limited Warranty
Toshiba America Information Systems, Inc., (“TAIS”) warrants that this voice processing equipment (except for fuses, lamps,
and other consumables) will, upon delivery by TAIS or an authorized TAIS dealer to a retail customer in new condition, be free
from defects in material and workmanship for twenty-four (24) months after delivery. This warranty is void (a) if the equipment
is used under other than normal use and maintenance conditions, (b) if the equipment is modified or altered, unless the
modification or alteration is expressly authorized by TAIS, (c) if the equipment is subject to abuse, neglect, lightning, electrical
fault, or accident, (d) if the equipment is repaired by someone other than TAIS or an authorized TAIS dealer, (e) if the
equipment’s serial number is defaced or missing, or (f) if the equipment is installed or used in combination or in assembly with
products not supplied by TAIS and which are not compatible or are of inferior quality, design, or performance.
Customer will, at its sole cost and expense, provide the necessary Uninterruptible Power Supply (UPS) equipment as specified
by TAIS in the Stratagy Voice Processing General Description for use with the Stratagy ES system at all times. System failures
and/or damages resulting from either not using a UPS with the Stratagy ES or the use of a UPS not equivalent to that specified by
TAIS are not covered by this warranty.
The sole obligation of TAIS or Toshiba Corporation under this warranty, or under any other legal obligation with respect to the
equipment, is the repair or replacement by TAIS or its authorized dealer of such defective or missing parts as are causing the
malfunction with new or refurbished parts (at their option). If TAIS or one of its authorized dealers does not replace or repair
such parts, the retail customer’s sole remedy will be a refund of the price charged by TAIS to its dealers for such parts as are
proven to be defective, and which are returned to TAIS through one of its authorized dealers within the warranty period and no
later than thirty (30) days after such malfunction, whichever first occurs.
Under no circumstances will the retail customer or any user or dealer or other person be entitled to any direct, special, indirect,
consequential, or exemplary damages, for breach of contract, tort, or otherwise. Under no circumstances will any such person be
entitled to any sum greater than the purchase price paid for the item of equipment that is malfunctioning.
To obtain service under this warranty, the retail customer must bring the malfunction of the machine to the attention of one of
TAIS’ authorized dealers within the twenty-four (24) month period and no later than thirty (30) days after such malfunction,
whichever first occurs. Failure to bring the malfunction to the attention of an authorized TAIS dealer within the prescribed time
results in the customer being not entitled to warranty service.
THERE ARE NO OTHER WARRANTIES FROM EITHER TOSHIBA AMERICA INFORMATION SYSTEMS, INC., OR
TOSHIBA CORPORATION WHICH EXTEND BEYOND THE FACE OF THIS WARRANTY. ALL OTHER WARRANTIES,
EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE, AND FITNESS FOR USE, ARE EXCLUDED.
No TAIS dealer and no person other than an officer of TAIS may extend or modify this warranty. No such modification or
extension is effective unless it is in writing and signed by the vice president and general manager, Telecommunication Systems
Division.
Contents
Introduction
Organization .............................................................................................................. vii
Conventions .............................................................................................................. viii
Action/Response Table ........................................................................................ ix
Related Documents/Media ........................................................................................... x
Stratagy eBrochure and Advisor CD-ROM .......................................................... x
Chapter 1 – The Grand Tour
Overview ...................................................................................................................... 2
Features to Personalize Your Mailbox ........................................................................ 4
Message Folders .......................................................................................................... 4
Single Message Folder .......................................................................................... 5
Dual Message Folders ........................................................................................... 5
Multiple Message Folders ..................................................................................... 6
Message Types ............................................................................................................. 8
Forwarded Message .............................................................................................. 8
Reply Message ...................................................................................................... 8
Fax Message .......................................................................................................... 9
E-mail Message ..................................................................................................... 9
Greetings .................................................................................................................... 10
Personal ............................................................................................................... 10
System ................................................................................................................. 10
Busy ..................................................................................................................... 10
Special Delivery Options ........................................................................................... 11
Urgent .................................................................................................................. 11
Private ................................................................................................................. 11
Stratagy ES User Guide
01/03
i
Contents
Chapter 2 –Getting Started
Return Receipt .....................................................................................................11
Future Delivery ...........................................................................................................11
Message Destination Selections .................................................................................12
Personal Distribution Lists ...................................................................................12
System Distribution Lists .....................................................................................13
Directory ..............................................................................................................13
User Options ...............................................................................................................14
User Prompts ..............................................................................................................15
Chapter 2 – Getting Started
User Tutorial ...............................................................................................................17
Step 1: Access Your Mailbox ....................................................................................18
Step 2: Record Your Name ........................................................................................20
Step 3: Record Your Personal Greeting ....................................................................21
Step 4: Change Your Security Code ..........................................................................22
Step 5: Exit Your Mailbox or User Mode .................................................................22
Chapter 3 – Play Messages
Access Messages ........................................................................................................24
Playback Controls .......................................................................................................24
Play Messages ............................................................................................................26
Special Functions .......................................................................................................29
Retrieve and Listen to E-mail Messages ....................................................................33
Chapter 4 – Send Messages
Recording Controls .....................................................................................................38
Send a Message ..........................................................................................................39
Forward a Message .....................................................................................................43
Reply to the Current Message ....................................................................................46
Special Delivery Options ............................................................................................48
Future Delivery ...........................................................................................................49
Send a Direct Fax .......................................................................................................50
ii
Stratagy ES User Guide
01/03
Contents
Chapter 5 –Manage Mailbox
Chapter 5 – Manage Mailbox
Change Greeting ........................................................................................................ 54
Create or Record Over a Personal Greeting ........................................................ 55
Select a Personal Greeting ................................................................................... 57
Review a Personal Greeting ................................................................................ 58
Change User Options ................................................................................................. 59
Change Do Not Disturb (DND) Setting .............................................................. 60
Change Call Screening Setting ............................................................................ 61
Change Security Code ......................................................................................... 62
Select Busy Greeting ........................................................................................... 63
Create or Record Over Busy Greeting ................................................................ 64
Record Your Name .............................................................................................. 66
Change Message Notification ............................................................................. 68
Set Automatic Message Copy ............................................................................. 70
Review Option Settings ....................................................................................... 73
Manage Personal Distribution Lists ........................................................................... 74
Manage Guest Mailboxes .......................................................................................... 76
Use Guest Mailboxes ................................................................................................. 77
Manage Personal Folders ........................................................................................... 78
Appendix A – Using Stratagy ES with a Strata CTX
Call Forward .............................................................................................................. 81
Message Waiting ........................................................................................................ 83
Responding to a Lit Msg LED ............................................................................ 83
Turning On/Off Message Waiting LED on Another Extension .......................... 84
Toshiba Proprietary Integration ................................................................................. 84
Soft Key Control of Voice Mail .......................................................................... 84
Call Record to Stratagy ES .................................................................................. 90
Direct Transfer to Voice Mailbox .............................................................................. 91
Voice Mail Conference .............................................................................................. 91
Stratagy ES User Guide
01/03
iii
Contents
Appendix B –Fax Printer Driver
Appendix B – Fax Printer Driver
Configure/Personalize Fax Printer Driver ..................................................................94
Use Fax Printer Driver ...............................................................................................97
SES Fax Client Screen ...............................................................................................98
Schedule Fax for Future Delivery ............................................................................100
Appendix C – Automatic Speech Recognition
Reach Destination .....................................................................................................102
Access Your Mailbox ...............................................................................................102
Send a Message ........................................................................................................103
Appendix D – Unified Messaging (UM) with Outlook Integration
Stratagy ES Message Window .................................................................................106
Address Book Feature ..............................................................................................108
Update Stratagy ES Address Book Manually ....................................................108
Update Stratagy ES Address Book Automatically ............................................108
Using UM Feature ....................................................................................................109
Voice Mail Options ..................................................................................................112
Play Voice Message ...........................................................................................112
Reply to Voice Message ....................................................................................113
Forward Voice Message ....................................................................................114
Send Voice Message ..........................................................................................115
View Fax ..................................................................................................................115
Appendix E – Unified Messaging with IP Integration
Configure Windows for Stratagy ES Codec .............................................................118
Check Codec is Installed on PC .........................................................................118
Configure Windows ..........................................................................................119
Record Stratagy ES Voice Messages (using Windows Sound Recorder) ................120
Send .WAV File as Voice Message .........................................................................121
Appendix F – Remote User Password Administration for TTS
Set Remote User Password .......................................................................................124
iv
Stratagy ES User Guide
01/03
Contents
Appendix G –Using Stratagy ES with a Strata Legacy System
Appendix G – Using Stratagy ES with a Strata Legacy System
Call Forward ............................................................................................................ 126
Set Call Forward to Stratagy ES ........................................................................ 126
Cancel Call Forward .......................................................................................... 130
Cancel the Programmed Call Forward Voice Mail Code .................................. 130
Message Retrieval .................................................................................................... 131
Glossary ...................................................................................................................... 133
Index .............................................................................................................................. 137
Stratagy ES User Guide
01/03
v
Contents
Appendix G –Using Stratagy ES with a Strata Legacy System
vi
Stratagy ES User Guide
01/03
Introduction
This guide describes the voice messaging capabilities and procedures for making the
Stratagy ES and Stratagy iES32 Voice Processing System work for you.
Organization
This guide is divided as follows:
• Chapter 1 – The Grand Tour is an overview of the Stratagy ES system. Topics
covered are: features to personalize your mailbox; an explanation of message
folders, greetings, types and destinations; special delivery options; and available
user options and prompts.
• Chapter 2 – Getting Started provides instructions on those features you need
when accessing Stratagy ES for the first time, including changing your security
code and recording your name.
• Chapter 3 – Play Messages contains step-by-step instructions on playing
messages.
• Chapter 4 – Send Messages details how to send, forward, and reply to a message.
• Chapter 5 – Manage Mailbox provides step-by-step instructions on recording
greetings, using destination (distribution) lists, and activating options such as Do
Not Disturb and Call Screening.
• Appendix A – Using Stratagy ES with a Strata CTX outlines Call Forward,
Message Waiting, Toshiba Proprietary Integration (i.e., Soft Key Control of Voice
Mail and Call Record features), and the Direct Transfer to Voice Mail and Voice
Mail Conferencing features.
• Appendix B – Fax Printer Driver provides step-by-step instructions on
configuring and using the fax printer driver.
Stratagy ES User Guide
01/03
vii
Introduction
Conventions
• Appendix C – Automatic Speech Recognition contains step-by-step instructions
on using the optional speech recognition feature.
• Appendix D – Unified Messaging with Outlook Integration contains step-bystep instructions on using the optional Unified Messaging feature.
• Appendix E – Unified Messaging with IP Integration contains instructions on
recording and sending a .wav file using Windows® Sound Recorder.
• Appendix F – Remote User Password Administration for TTS provides
instructions on how to update the Stratagy ES software with your e-mail log on
password so that the system can read your e-mail messages via Text-to-Speech
(TTS).
• Appendix G – Using Stratagy ES with a Strata Legacy System explains how to
program your Toshiba proprietary telephone for Call Forward and Message
Retrieval when using your integrated Stratagy ES system.
• Glossary defines frequently-used Stratagy ES voice processing system features
and functions.
• Index
Conventions
Conventions
Note
Important!
Extension Number
Description
Elaborates specific items or references other information. Within
some tables, general notes apply to the entire table and numbered
notes apply to specific items.
Calls attention to important instructions or information.
Press to answer a call to the Extension Number. Each station can have
multiple extension buttons. Incoming calls ring the extension button(s)
from the top down. For example, station 10’s extensions ring 10-1 first,
then 10-2, 10-3, and 10-4. A station is considered busy when all
extensions are being used.
Note
viii
The naming convention for DKT assignments within Toshiba is
Directory Numbers. For clarity and ease of understanding, the
terms Extension Number and Phantom Extension Number will be
used in this document in lieu of PDN and PhDN.
Stratagy ES User Guide
01/03
Introduction
Conventions
Conventions
$ULDOEROG
Courier
Description
Represents telephone buttons.
Shows a computer keyboard entry or screen display.
“Type”
Indicates entry of a string of text.
“Press”
Indicates entry of a single key. For example: Type prog then press
Enter.
Plus (+)
Shows a multiple PC keyboard or phone button entry. Entries
without spaces between them show a simultaneous entry. Example:
Esc+Enter. Entries with spaces between them show a sequential
entry. Example: # + 5.
Tilde (~)
Means “through.” Example: 350~640 Hz frequency range.
➤
Denotes the step in a one-step procedure.
➤
Denotes a procedure.
See Figure 10
Grey words within the printed text denote cross-references. In the
electronic version of this document (Library CD-ROM), crossreferences appear in blue hypertext.
Action/Response Table
Actions you perform appear
in this column. They can
consist of either a single step
or a series of numbered
steps.
Stratagy ES User Guide
01/03
The immediate response to the action performed
appears in this column. Additional notes and comments
are also included.
ix
Introduction
Related Documents/Media
Related Documents/Media
Note Some documents listed here may appear in different versions on the CD-ROM
or in print. To find the most current version, check the version/date in the
Publication Information on the back of the document’s title page.
Important!
•
•
•
•
•
Read this User Guide first, then use it with the Quick Reference Guide.
Stratagy General Description
Stratagy Enterprise Server (ES) Installation & Maintenance Manual
Stratagy Enterprise Server System Administrator Guide
Stratagy Enterprise Server Quick Reference Guide
Stratagy Library CD-ROM
Stratagy eBrochure and Advisor CD-ROM
Packaged with every Stratagy shipped is a CD-ROM containing Stratagy eBrochure,
and an end-user tutorial, Stratagy Advisor. Additional copies of this CD-ROM can be
purchased from your Dealer Sales Representative.
eBrochure
The eBrochure provides a description of each of the Stratagy products along with
audio supplemented mini-demonstrations illustrating the capabilities of Stratagy voice
processing. Also included on the CD-ROM is an electronic copy of this Stratagy
General Description.
Advisor
The Stratagy Advisor is an end-user tutorial that can be used as a learning tool for the
new user or as a refresher course for existing Stratagy users.
The Stratagy Advisor program covers general topics—such as play messages, send
messages, etc.—that are applicable to all models of Stratagy systems. The Stratagy
iES32 and Stratagy ES tutorials are separated into two sections: the Telephone User
Interface (TUI) and Unified Messaging. All presentations interact with the viewer in
order to provide a better understanding of how Stratagy works.
x
Stratagy ES User Guide
01/03
The Grand Tour
1
This chapter provides an overview of the system and covers the following general
topics:
•
•
•
•
•
•
•
•
•
Features to personalize your mailbox
Message folders
Message types
Greetings
Special delivery options
Message destinations
User options
User prompts
User Tutorial (New User)
Stratagy ES User Guide
01/03
1
The Grand Tour
Overview
Overview
Stratagy ES manages multiple voice processing functions simultaneously 24-hours-aday, seven-days-a-week. Your mailbox is always available for callers to leave private
voice or fax (optional feature) messages. In addition, you can update your greeting at
your convenience or send and receive messages from any touchtone telephone.
Callers control their own progress through the system. They no longer have to wait for
a person to answer the telephone. If your extension is busy or you do not answer,
callers can transfer to an operator, call another extension, or record a private, detailed
message.
A representative in your company is assigned as the System Administrator for the
system. The System Administrator is responsible for system maintenance that
includes configuring your mailbox to suit your needs.
The configuration affects how and which features you can access. Whenever possible,
this guide provides information concerning feature exceptions and which features may
be configured to work differently.
You can access your mailbox from any tone-dialing telephone using your security
code. After you access Stratagy ES, you hear the number of messages you have in
your message folder(s), followed by a prompt from the Main Menu options (see
Figure 1). You can then:
•
•
•
•
•
Listen to your messages
Send or forward messages
Reply to messages
Manage your mailbox (e.g., change your greetings, create distribution lists, etc.)
Listen to your e-mail messages
Note This feature is only available to users of Stratagy ES with Unified Messaging
(UM) and Text-to-Speech (TTS) capabilities. Check with your System
Administrator to find out if your system is configured for this feature.
2
Stratagy ES User Guide
01/03
Stratagy ES User Guide
01/03
Exit User Mode
Cancel message and select new
destination
Cancel and Return to Main Menu
Set Return Receipt request
(On/Off)
Return to previous menu
Set Future Delivery
Record
Record a message, comment or reply
(Press
when finished.)
Send and Return to Main Menu
Review recording
Re-record
Append recording
Select Additional Destinations
Mailbox number plus
Directory
Personal Distribution List
(1~25)
Press
when finished.
Special Delivery Options
Set Urgent status (On/Off)
Set Private status (On/Off)
Multiple Destinations
Personal Distribution List (1~25)
Directory plus name
Mailbox number plus
Enter one of the following:
SEND MESSAGES
Stratagy ES Main Menu
Requires UM and TTS
Optional feature
Figure 1
††
†
Future Delivery Review
(Play, Save, Delete)
Continuous Delete
Access New/Saved message folders
(toggle)
Continuous Play
Return to previous menu
Send Current Fax to fax machine for
print†
Message Date and Time
Send All Fax documents to fax
machine for print within a folder†
Immediate Fax print of current fax
document†
Immediate Fax print of all fax
documents within a folder†
Return to Main Menu
(number of messages to be deleted
plays)
Play the next message
Replay the current message
Save the current message
Standard Save Message Folder
~
Personal Message Folder(s)
Play the Previous message
Delete the current message
Forward the current message
Reply to the current message
Special Functions
PLAY MESSAGES
MAIN MENU
Select
~
for a Personal Message
Folder
Review folder name/comment
Record folder name/comment
Return to previous menu
Return to a Main Menu
Change Greeting
Select
~
for a Personal Greeting
or
for the System Greeting
Change User Options
Change Do Not Disturb (On/Off)
Change Call Screening (On/Off)
Change Security Code
Select Busy Greeting (toggle)
Record Busy Greeting
Record your Name
Change message Notification
Set Automatic Message Copy
Review Option Settings
Return to previous menu
Manage Personal Distribution Lists
Manage Guest Mailboxes
Manage Personal Message Folders
MANAGE MAILBOX
HANG UP
Return to Main Menu
(number of e-mail messages to be
deleted plays)
Delete e-mail messages
Cancel deletion of e-mail
messages
5464
Reply to the current e-mail message
Forward the current e-mail message
Listen to e-mail message
Replay the current e-mail message
Save the current e-mail message
Delete the current e-mail message
Retrieve and Listen to
E-MAIL MESSAGES††
The Grand Tour
Overview
3
The Grand Tour
Features to Personalize Your Mailbox
Features to Personalize Your Mailbox
The Stratagy ES Voice Processing System offers a variety of features to personalize
your mailbox. The following are a few of those features:
• Mailbox Security Code – Your mailbox has a security code. The code must be
entered by you in order to “log into” your mailbox, giving you access to your
messages, settings, greetings, etc. (see “Change Your Security Code” on page 22).
• Name Recording – Your name is announced whenever the directory is accessed,
you select the system greeting, or a message is sent by another Stratagy ES user.
When you first enter your mailbox, you need to record your name (see “Record
Your Name” on page 20).
• Personal Greetings – You can record up to seven personal greetings that are
played when you are unavailable (see “Change Greeting” on page 54).
• Guest Users – You can create guest mailboxes that can be used by clients, friends,
etc. Users frequently use this feature to create guest mailboxes for clients, so that
they can easily exchange confidential information (see “Manage Guest Mailboxes”
on page 76).
• Personal Folders – You can save your messages in up to seven personal folders
you create. The folders are for only your use and you can change them whenever
necessary (see “Manage Personal Folders” on page 78).
Message Folders
Messages in the Stratagy ES are stored in message folders and play in the order
received – FIFO (First In, First Out) or LIFO (Last In, First Out).
Your mailbox has one of the following folder configurations:
• A single message folder where all messages reside.
• Dual message folders – new, saved.
• Multiple message folders where, in addition to the new and saved folders, you can
create up to seven personal folders for your messages.
Note Consult your System Administrator for your mailbox’s programming.
4
Stratagy ES User Guide
01/03
The Grand Tour
Message Folders
Single Message Folder
Your messages reside in one message folder. When you access your mailbox,
Stratagy ES announces you have “x messages, y is (are) new, z is (are) urgent, w
fax(es).” New messages play based on the type (urgent messages play first) and order
received (FIFO/LIFO). If no new messages exist, Stratagy ES plays any saved
messages in the mailbox.
After you play the last message in the folder, Stratagy ES prompts, “End of
messages.” You can choose to return to the top of the folder, etc.
Dual Message Folders
Your messages reside in one of two folders—new or saved. When you access your
mailbox, Stratagy ES announces you have “x new, y is (are) urgent and z saved
messages, w fax(es).”
New Message Folder
New messages consist of messages that are unheard.
When you pressfrom the Main Menu to play messages, Stratagy ES automatically
accesses the New Message Folder. A new message begins to play based on the type
(urgent messages play first) and order received (FIFO/LIFO). After you play the last
message in the folder, Stratagy ES prompts, “End of messages.” You can choose to
return to the top of the folder, or go to the top of the saved folder.
Your Message Waiting LED only extinguishes when all new messages have been
either deleted or saved.
Note You can enable a Message Pending feature on your mailbox. When enabled, the
system marks new messages that have been partially heard (for more than two
seconds by default) as Pending. Pending messages remain in the New Message
Folder; however, if the New Message Folder contains only Pending Messages,
your Message Waiting LED goes out. This allows you to retain messages in the
New Message Folder, yet alert you when new messages arrive. Messages
marked as Pending also submit a Return Receipt notification to the sender of
the message, if it was requested. Consult your System Administrator for further
information.
Stratagy ES User Guide
01/03
5
The Grand Tour
Message Folders
If no new messages exist, Stratagy ES automatically accesses the Saved Message
Folder. If you are in the Saved Message Folder, you can toggle back to the New
Message Folder by pressing.
Saved Message Folder
Saved messages consist of messages that:
• You save by pressing either during or after playing the message. Stratagy
prompts, “This message will be saved in the Saved Message Folder.”
• Stratagy ES automatically saves when you do not press (delete) after playing the
message.
Messages are not moved to the Saved Message Folder until you log out of your
mailbox, enabling you to return to the new message folder and replay the message.
Access the Saved Message Folder from the Main Menu by pressingor from the
New Message Folder by pressing. Stratagy ES automatically accesses the Saved
Message Folder when no new messages exist.
After you play the last message in the folder, Stratagy ES prompts, “End of
messages.” You can choose to return to the top of the folder, or go to the top of the
new message folder by pressing .
Multiple Message Folders
Your messages reside in up to nine folders— one new (folder 0), one saved (folder 1)
and up to seven personal folders (folders 2~8), created by you for the purpose of
saving your messages. The personal folders are for only your use. When you access
your mailbox, Stratagy ES announces the number of messages you have in the same
manner as the example in “Dual Message Folders” on page 5.
Message folders enable you to store saved messages topically, providing better
organization of important correspondence. You can record a comment for each folder,
such as “Messages from Toshiba America,” to assist you in locating the right folder in
which to store or retrieve a message.
Note To create or change personal folders, see “Manage Personal Folders” on page
78.
6
Stratagy ES User Guide
01/03
The Grand Tour
Message Folders
New Message Folder
The New Message Folder is configured identically for both the Dual Message and
Multiple Message Folder mailboxes with the following exception:
If no new messages exist in a Multiple Message Folder mailbox, Stratagy ES accesses
the Saved Message Folder (if you have not created any personal folders) or plays the
name/comment/number of all available personal folders. You are then requested to
enter the folder number.
Saved Message Folder/Personal Message Folders
Saved messages consist of messages that:
• Stratagy ES automatically saves when you do not press (delete) after playing the
entire message. The message is saved in the Saved Message Folder (folder 1), the
default destination for saved messages. Stratagy ES prompts, “This message will
be saved.”
• You save by pressing either during or after playing the message. Stratagy ES
checks your mailbox for Personal Message Folders.
If personal folders do not exist, Stratagy ES saves the message in the Saved
Message Folder (folder 1). Stratagy prompts, “This message will be saved.”
If Personal Message Folders do exist, Stratagy ES plays the recorded name/
comment and number of all available personal folders. You are requested to enter a
valid folder number where you want the message saved. If you know the personal
folder number you want, you can select it at anytime. You do not have to listen to
the entire list of available folders. If an invalid number is entered, Stratagy ES
automatically saves the message in folder 1.
Messages are not moved to a “save” folder until you log out of your mailbox, enabling
you to return to the new message folder and replay the message.
After you play the last message in the folder, Stratagy ES prompts, “End of
messages.” You can choose to return to the top of the folder, go to the top of another
folder, etc.
Stratagy ES User Guide
01/03
7
The Grand Tour
Message Types
Access Folders
When you press from the New or Saved Message Folders or from the Main
Menu, Stratagy ES checks your mailbox for personal folders. Depending upon
whether it finds any, Stratagy ES performs the following procedures:
Access Method
No Personal Folders
From New or Saved
Message Folder, press .
From Main Menu, press
.
Personal Folders
Stratagy ES prompts you to:
Goes to Saved Message
Folder.
•
Enter a personal folder number.
or press...
•
for the New Message Folder.
•
for the Saved Message Folder.
Message Types
The Stratagy ES has the following special types of messages—forwarded, reply, fax,
and e-mail.
Forwarded Message
Any message sent to you can be forwarded to one or more individual destinations or a
personal or system distribution list. When forwarding a message, recording a message
(comment) is optional.
Reply Message
Messages from other Stratagy ES users to which you want to send an immediate
response can be sent as a reply message. When replying to a message, Stratagy ES
does not prompt you to select the destination if the original message was recorded
within a user’s mailbox. If the message was not recorded from a user’s mailbox, you
can still reply to the message but the system requests that you enter a destination
mailbox number.
When listening to a reply message, a prompt notifies the user of the name/mailbox
number of the person who sent the reply.
8
Stratagy ES User Guide
01/03
The Grand Tour
Message Types
Fax Message
Note Fax Messaging is an optional feature in the Stratagy ES. Check with your
System Administrator to find out if your system is configured for this feature.
Fax messages can be sent to your mailbox and stored or forwarded along with voice
messages. When you access your mailbox, Stratagy ES tells you the number of fax
messages that are in your mailbox. Once you access the fax message, Stratagy ES
plays the header information that includes the number of pages received. You cannot
listen to the actual fax document.
You can forward the fax to other users as you would a voice message, including
sending a voice comment with the fax to provide information about the message. You
can also print the fax. See “Special Functions” on page 29 for details.
E-mail Message
Note This feature is only available to users of Stratagy ES with Unified Messaging
(UM) and Text-to-Speech (TTS) capabilities. Check with your System
Administrator to find out if your system is configured for this feature.
You can retrieve and listen to your e-mail messages from your mailbox. Once you
access the e-mail message, Stratagy ES plays the header information that includes
sender information and time and then plays the content. Upon playing the e-mail
message you can:
• Delete it from your e-mail Inbox on your computer. e-mails that are not deleted
remain in your e-mail Inbox and are played the next time you access this function.
• Forward it to other users that have UM privileges. The destination user must have
both a Stratagy ES voice mailbox and an e-mail address that has been defined in
the destination user’s mailbox.
• Reply to a e-mail message. The Stratagy ES generates an e-mail message with your
recorded reply attached as an audio .wav file, and sent back to the originator.
Stratagy ES User Guide
01/03
9
The Grand Tour
Greetings
Greetings
You can select either a personal or system greeting to play to callers when you do not
answer or when your telephone is busy.
Depending on how your system is configured, callers may hear a separate busy
greeting—the system or the custom busy greeting. See “Change User Options” on
page 59 for details.
Personal
Personal greetings are greetings that you record for callers. Stratagy ES stores all
recorded greetings under the personal greeting number (1~7) for your mailbox. Using
the greeting number, you can select which greeting plays.
The System Administrator can also schedule your greetings to automatically play at
different times. If you choose, you can override the automatic schedule using “Select a
Personal Greeting” on page 57.
System
The system greeting is a standard prerecorded greeting with all Stratagy ES systems. It
cannot be recorded over or deleted. The greeting states, “Please leave a message for
(name).” Stratagy ES adds your name from the name recording that you made (see
“Record Your Name” on page 20).
Busy
If your mailbox is configured for a personal busy greeting, you can record a custom
busy greeting that plays when your extension is busy. If a custom greeting is not
recorded, the default system busy greeting plays.The custom busy greeting can also be
turned On/Off using the Select Your Busy Greeting option on the Change User
Options Menu (see “Select Busy Greeting” on page 63).
Note The System Administrator must configure your mailbox for the custom busy
greeting option to be available.
10
Stratagy ES User Guide
01/03
The Grand Tour
Special Delivery Options
Special Delivery Options
In addition to recording and sending a new message, you can mark the message
urgent, private, or request a return receipt.
Urgent
Messages can be marked urgent by the sender and always play first in the New
Message Folder. After the message plays, the urgent status is removed.
Private
Messages can be marked private by the sender. The same options, such as saving and
deleting, apply to the private messages; however, a private message cannot be
forwarded or copied using the Automatic Message Copy feature. Once a message is
sent, the private status cannot be removed.
Return Receipt
You can mark a message for Return Receipt if you want verification that it has been
played. When a user completely plays a message marked for Return Receipt, a
notification is sent back to the sender. Stratagy ES notifies the sender the time the
message was heard and by whom and then plays the original message as a reminder of
the message. This can be helpful if multiple messages were sent to the same
destination with Return Receipt requested.
Future Delivery
Stratagy ES can be configured so that your message is delivered at a future specified
time and date. After marking the message for future delivery, you can review (play,
save, delete) the message at any time before it is sent (see “ Future Delivery Review”
on page 30).
Stratagy ES User Guide
01/03
11
The Grand Tour
Message Destination Selections
Message Destination Selections
At the beginning of the Send Messages menu, you are asked to enter the destination
mailbox number(s).You can choose to enter a single destination (e.g., mailbox
number) or multiple destinations (e.g., mailbox number, personal lists). Using the
Multiple Destinations option enables you to address your message to all the recipients
at the start of the menu.
You can then record your message and, if desired, add additional destinations when
prompted later in the menu. Valid destinations are:
• Mailbox Number
Note If you don’t know the user’s mailbox number, you can locate the mailbox
number on Stratagy ES’s system-wide directory by pressing .
•
•
•
•
Personal distribution list
System distribution list
Audio Messaging Interchange Specification (AMIS) Proxy mailbox number
AMIS Gateway number plus a remote mailbox number
Note AMIS analog networking is an optional feature and enables a Stratagy mailbox
user to send, receive and reply to relayed voice messages over any remote voice
mail system that supports the AMIS analog protocol.
See “Send a Message” on page 39 for instructions on using these options.
Personal Distribution Lists
You can create up to 25 Personal Distribution Lists consisting of other system users.
You can add or delete users at any time. The lists are for only your use.
At the time you create a list, you are given the option of recording a “list comment”
that serves as the title or name for the list. The comment plays each time you use the
list to confirm that you have chosen the correct distribution list.
12
Stratagy ES User Guide
01/03
The Grand Tour
Message Destination Selections
System Distribution Lists
In addition to Personal Distribution Lists, Stratagy ES supports system-wide
distribution lists created by the System Administrator for use by everyone in your
company. You should check with your System Administrator to find out which lists
are available.
The “list comment” for the selected system list is played whenever you enter the
mailbox number to confirm that the right list has been chosen.
Important!
When creating lists, you should keep in mind that Stratagy ES does not
check for duplicate users on separate lists when sending a message. For
example, if you select Personal Distribution List #1 and #3 as destinations for your message and Mailbox Number 1001 is on both lists, the
message is sent twice to Mailbox Number 1001.
Directory
Using your telephone’s dial pad, you can enter the digits corresponding to the first few
letters of a user’s name or the first letters of a system distribution list name.
Stratagy ES plays the recorded name and mailbox number that matches the
combination of entered digits. You can then select the name or go on to the next name
in the directory.
Each mailbox can be identified with up to two names. These names are entered into
the automated directory by the System Administrator and enhance the directory’s
search/find capabilities. Common choices for the names are the first and last names of
the user, last name of the user and a commonly misspelled version of the last name or
in the case of a system distribution list, two words that might appear in the list title.
Stratagy ES User Guide
01/03
13
The Grand Tour
User Options
User Options
You can set your mailbox for Do Not Disturb (DND) or call screening, select or record
a busy greeting (plays when your telephone is busy), designate where or how you are
notified of a message, and set your mailbox to automatically copy messages to another
mailbox.
The following is a brief description of each of the options. Please see “Change User
Options” on page 59 for more detailed information.
Important!
The System Administrator must activate these features for them to be
available.
• DND – When a caller enters your extension number, the Stratagy ES automatically
sends the call to your mailbox without first ringing your telephone.
• Call Screening – Stratagy ES asks callers for their name. Without the caller’s
knowledge, the system relays that information to you. You can decide to receive
the call, let the call forward to your mailbox, or transfer the call to another
extension with or without an announcement.
• Busy Greeting – You can record your own custom busy greeting that plays when
callers reach your extension, and it is busy.
• Message Notification – Your mailbox can have notification records programmed
by the System Administrator with a specific notification method (message waiting
lights, pagers, voice, etc.) and the time/day when that notification record applies.
Once you have turned on a specific notification record, Stratagy ES automatically
calls you at the designated number and with the chosen method to notify you of
your messages.
• Automatic Message Copy – You can set your mailbox to automatically copy all
messages or just urgent messages to another mailbox during specified times of the
day.
14
Stratagy ES User Guide
01/03
The Grand Tour
User Prompts
User Prompts
The Stratagy ES system prompts only for menu options available to you. You do not
hear prompts for options:
• Not available in your Stratagy ES system (i.e., fax).
• Not configured for your mailbox by the System Administrator (e.g., guest users,
DND).
Check with your System Administrator to verify which user options and features are
available to you.
Stratagy ES User Guide
01/03
15
The Grand Tour
User Prompts
16
Stratagy ES User Guide
01/03
Getting Started
2
This chapter instructs you on accessing and exiting your mailbox and outlines the user
tutorial steps.
User Tutorial
When you log on to the Stratagy ES Voice Processing system for the very first time,
you hear a tutorial that walks you through the following basic steps:
• Record your name. Your name is announced whenever the directory is accessed,
you select the system greeting, or another Stratagy ES user sends a message to you.
• Record your personal greeting. Your personal greeting automatically plays when
you are not available to answer your telephone.
• Change the default security code for your mailbox to ensure privacy. You should
change it on a regular basis.
Note If you do not complete the tutorial before hanging up, Stratagy ES saves any
completed portion (e.g., your name recording) and restarts where you left off
the next time you log on to your mailbox. Once the Stratagy ES tutorial is
completed successfully, it cannot be replayed.
Stratagy ES User Guide
01/03
17
Getting Started
Step 1: Access Your Mailbox
Step 1: Access Your Mailbox
The Main Menu (shown below) is your starting point for all of Stratagy ES’s
messaging features. Pressing from most menus returns you to the Main Menu.
To access your mailbox, you need to know:
• The telephone number to access Stratagy ES
• Your mailbox number
• Your default security code
Please ask your System Administrator if you do not have this information.
MAIN
MAINMENU
MENU
Play Messages
Send Messages
Manage Mailbox
Listen to E-mail Messages
Messages
Exit user mode
Exit user
Hang
Up mode
Each time you access your mailbox, Stratagy ES announces:
• The number of new and saved messages you have in your message folder(s).
• The number of messages that will be purged upon exiting your mailbox, if
applicable.
Stratagy ES then plays the Main Menu options.
18
Stratagy ES User Guide
01/03
Getting Started
Step 1: Access Your Mailbox
If you receive new messages while you are logged on to your mailbox, Stratagy ES
informs you that new messages have arrived every time you return to the Main Menu.
1. From an internal telephone,
call Stratagy ES on
___________
...or from an external
telephone, call Stratagy ES
on ___________.
2. When Stratagy ES answers,
press .
3. Enter your mailbox
number.
4. Enter the default security
code.
If you make a mistake
while entering the code,
press to re-enter.
The system answers with your standard
company greeting.
Stratagy ES prompts you to enter your mailbox
number.
Stratagy ES prompts you to enter your security
code.
You are now in your mailbox. Stratagy ES plays
the number of messages you have and then
prompts you with a list of choices from the
Main Menu.
Note If the Stratagy ES is fully integrated with the telephone system, Stratagy ES is
informed of your mailbox number and prompts you for your security code.
Consult your System Administrator for information on how your system is
integrated.
Stratagy ES User Guide
01/03
19
Getting Started
Step 2: Record Your Name
Step 2: Record Your Name
Your name is announced whenever the directory is accessed, you select the system
greeting, or a message is sent by you to another Stratagy ES user.
When you first enter your mailbox, the Stratagy ES tutorial prompts you to record
your name and walks you through the entire recording sequence. You can re-record
your name at any time (see “Record Your Name” on page 66).
1. At the tone, state your name
slowly and clearly (if you
like, you can also state your
extension).
2. Press when done.
3. After your name plays,
press:
To accept the recording
Re-record
20
Stratagy ES plays your name recording.
Your recording becomes part of your mailbox
and Stratagy ES prompts you to record your
personal greeting.
Stratagy ES returns you to the record your name
prompt.
Stratagy ES User Guide
01/03
Getting Started
Step 3: Record Your Personal Greeting
Step 3: Record Your Personal Greeting
The tutorial now prompts you to record your personal greeting. This greeting becomes
your Personal Greeting #1. You can record up to six other greetings (see “Create or
Record Over a Personal Greeting” on page 55 for instructions).
Personal greetings should be informative and advise callers when you will be
available to return their calls or respond to their messages. You can update personal
greetings as often as you want.
Sample Greeting
“Hi. This is Mary Smith of the Toshiba Marketing Department. It is Monday, June 19,
and I am in the office today. I am either on the telephone or have stepped away for a
few minutes and your call has been forwarded to my voice mailbox. If at the tone you
leave a detailed message and a telephone number where I can reach you, I will be
happy to return your call.”
1. At the tone, begin recording
your greeting.
2. Press when done.
3. After your greeting plays,
press:
To accept the recording
Re-record
Stratagy ES User Guide
01/03
The following information should be included:
•
•
•
•
•
•
Your name
Company and/or department
Date
Your availability
Instructions to leave a detailed message
Call coverage options
Stratagy ES plays your greeting.
Your greeting becomes Personal Greeting #1
and Stratagy ES prompts you to change your
security code.
Stratagy ES returns you to the record your
greeting prompt.
21
Getting Started
Step 4: Change Your Security Code
Step 4: Change Your Security Code
You should change your security code on a regular basis to ensure the privacy of your
messages and personal greetings (see “Change Security Code” on page 62).
Stratagy ES prompts you to enter your new security code and notifies you of the
number of allowable digits. For example, Stratagy ES might prompt “the new security
code must have at least three digits and 16 maximum digits” or “the new security code
must be exactly four digits.”
1. Enter your new security
code + .
2. Re-enter your new security
code + .
Stratagy ES prompts you to re-enter your new
security code for verification.
After entering the security code a second time,
Stratagy ES announces that your security code
has been changed.
You have completed the tutorial. Stratagy ES announces “mailbox number xxx is
enabled,” and announces the number of messages in your mailbox. You can now
perform any of the functions available on the Stratagy ES Main Menu or exit the
mailbox.
Step 5: Exit Your Mailbox or User Mode
➤ To exit your mailbox, press
to hang up
...or to exit the user mode,
press .
Stratagy prompts, “Thank you for calling.
Good-bye.”
Stratagy ES can be configured so that you can
exit your mailbox without leaving the
Stratagy ES system. Please ask your System
Administrator to find out if your system is
configured for this or some other function when
pressing.
If you have the “0 to EXIT User Mode”
capability, you hear Stratagy ES’s instructional
greeting. You can now access another user or a
different mailbox.
22
Stratagy ES User Guide
01/03
Play Messages
3
This chapter explains how to use the Play Messages feature. It covers:
•
•
•
•
•
Accessing messages
Playback controls
Playing messages
Special functions
Retrieve and listen to e-mail messages
Stratagy ES lights the message waiting light on your telephone when a voice or fax
message has been left for you on the Stratagy ES system.
Note Your telephone system and telephone must support a message waiting light for
this feature to function.
If configured, Stratagy ES automatically turns off your message waiting light on your
telephone when your new message folder is empty or only Pending messages remain
(see “Message Folders” on page 4).
All new messages must be deleted, saved, or pending (partially heard) for Stratagy ES
to turn off the message waiting light on your telephone. The Message Waiting LED
remains on only if there are new messages in the folder.
Stratagy ES User Guide
01/03
23
Play Messages
Access Messages
Access Messages
Once you press to play your messages, the following telephone keys assist you in
going through your messages:
Takes you to the next message or back to the top of the folder when you have
reached the last message in the folder.
Replays the current message.
you to the previous message or back to the last message in the folder when
Takes
you have reached the top of the message folder.
If you receive new messages while you are accessing your mailbox, Stratagy ES
notifies you every time you return to the Main Menu that new messages have arrived.
Note See “Message Folders” on page 4 on using access keys and .
Playback Controls
While playing a message, you can pause, control the volume, location, and speed of
playback using the following keys (shown below).
Press
to play Previous Message
(from first message go to last)
Play Next Message
(from last message go to first)
Pause/Resume
(toggle or 30 secs.)
Turn Up volume
Go Forward (advance)
Back Up (rewind)
3095
Press twice to
Change Speed (toggle)
Turn Down volume
24
Stratagy ES User Guide
01/03
Play Messages
Playback Controls
Play Next Message
Plays next message in folder. If you are at the last message in the folder, goes to the
first message in the same folder.
Replay Current Message
Plays previous message in folder. If you are at the first message in the folder, goes to
the last message in the same folder.
Play Previous Message
Plays previous message in folder. If you are at the first message in the folder, goes to
the last message in the same folder.
Pause/Resume (toggle or 30 seconds)
At any time while playing messages, you can press to pause the playback. The
message resumes playing as soon as you press or automatically at the end of a
defined amount of time (default is 30 seconds). You can pause the playback as many
times as necessary.
Turn Up Volume, Turn Down Volume
Each time you pressor, the volume of messages adjusts one increment until the
maximum number of increments is reached. Stratagy ES saves the current level when
you exit.
Back Up (rewind)
The message backs up/rewinds and then begins playing. The default is five seconds
(set by the System Administrator).
Go Forward (advance)
The message goes forward/advances and then begins playing. The default is five
seconds (set by the System Administrator).
Change Speed (toggle)
Two speeds are available for playing messages: normal and fast (level set for your
mailbox by the System Administrator). When you exit the Play Messages Menu, the
system returns to the default speed.
Stratagy ES User Guide
01/03
25
Play Messages
Play Messages
Play Messages
When you access your mailbox, Stratagy ES tells you the number of urgent, new,
saved, and fax messages (if supported by your system; check with your System
Administrator) you have in your mailbox.
When you press from the Main Menu to play messages (menu shown below),
Stratagy ES automatically accesses the New Message Folder. If no messages exist in
the New Message Folder, Stratagy ES automatically accesses the Saved Message
Folder or Personal Folders.
If your mailbox is empty, the Stratagy ES Main menu prompt does not include “press
to play messages.”
From the Main Menu:
Play Messages
Play the next message
Replay the current message
Save the current mesage
Play the Previous message
Delete the current message
Forward the current message
Reply to the current message
Special Functions
Immediate Fax print of all fax documents
within a folder†
Immediate Fax print of current fax document†
Send All Fax documents to fax machine
for print within a folder†
While playing a message, you can press:
Pause/Resume (toggle or 30 seconds)
Turn Up volume
Turn Down volume
Backup (rewind)
Go Forward (advance)
Change Speed (toggle)
4554
Send Current Fax to fax machine for print†
Message Date and Time
Future Delivery Review (Play, Save, Delete)
Continuous Delete
New/Saved message folder (toggle)
Continuous Play
Return to previous menu
Return to the Main Menu
† Optional feature
26
Stratagy ES User Guide
01/03
Play Messages
Play Messages
1. From the Main Menu,
press.
While the message plays,
you can select to pause/
resume, to turn up
volume, to turn down
volume, to back up
(rewind), to go forward
(advance), and/or to
change speed (toggle).
2. (Optional) While the
message plays or
immediately after, you can
select one of the following:
Play the next message
A message plays.
Skips to the beginning of the next message.
Note If you reach the end of your messages,
pressing takes you back to the top of
Save the current
message
(Optional) For Multiple
Folder mailboxes:
Enter a folder number
( for Saved Message
Folder, ~ for Personal
Folders).
Note To create or change
the same folder.
Single or dual message folders: Stratagy ES
saves the message and the Play Messages Menu
plays.
Multiple message folders: Stratagy ES plays the
recorded names/comment/numbers of all
available folders. You are requested to enter a
valid folder number where you want the
message saved.
If an invalid number is entered, Stratagy ES
automatically saves the message in folder .
personal folders, see
“Manage Personal
Folders” on page 78.
Stratagy ES User Guide
01/03
27
Play Messages
Play Messages
Note Messages are not moved to the saved
folder until you log out of your mailbox,
enabling you to return to the new
message folder and replay the message.
Delete the current
message
The Play Messages Menu plays.
Flags the current message for deletion. The Play
Messages Menu plays. When you exit Play
Messages, Stratagy ES tells you the number of
messages to be deleted. If you do not want to
delete a message, save the message before
exiting your mailbox.
Note Stratagy ES can be programmed to purge
Forward the current
message
Reply to the current
message
Special Functions
Replay the current
message
Play the previous
message
messages after a preset length of time.
Consult your System Administrator.
Stratagy ES notifies you before purging
messages.
With the exception of private messages, all
messages can be forwarded to a single user,
multiple users, or a destination list. See
“Forward a Message” on page 43 for details on
this feature.
Your reply is sent to the originator of the
message. In addition, you can send your reply to
a single user, multiple users, or a destination list.
See “Reply to the Current Message” on page 46
for details on this feature.
Stratagy ES prompts with the options. See
“Special Functions” on page 29 for instructions
on using this option.
The current message plays from the beginning.
The previous message plays from the beginning.
Note If you are at the top of the message
folder, pressing takes you to the
bottom of the same folder.
28
Stratagy ES User Guide
01/03
Play Messages
Special Functions
Return to Main Menu
Stratagy ES tells you the total number of
messages that will be deleted when you log out
of your mailbox, and then returns to the Main
Menu.
Special Functions
You can print or send faxes, check the date and time a message was sent, or review a
message set for future delivery in the Play Messages Menu.
When you play a message, this option is available by pressing Special Functions.
Note If a message does not contain a fax, Stratagy ES does not play Fax options.
➤ Press an option number:
Immediate Fax print of
all fax documents
within a folder
Immediate Fax print of
current fax document
Send all Fax documents
within a folder to a fax
machine for print
Enter fax machine’s
telephone number.
Press to accept entry
...or to re-enter fax
number.
Send Current Fax to fax
machine for print
Stratagy ES User Guide
01/03
Retrieves (prints) all the faxes from your
mailbox while calling from a fax machine (or
other device capable of receiving a fax) with a
handset.
Retrieves (prints) the current fax from your
mailbox while calling from a fax machine (or
other device capable of receiving a fax) with a
handset.
Stratagy ES prompts for the fax machine’s
telephone number.
The system sends all fax messages to a fax
machine (or other device capable of receiving a
fax) for retrieval (print). The Play Messages
Menu plays.
Stratagy ES prompts for the fax machine’s
telephone number.
29
Play Messages
Special Functions
Enter fax machine’s
telephone number.
Press to accept entry
...or to re-enter fax
number.
Message Date and Time
The system sends a fax message currently
residing in your mailbox to a fax machine (or
other device capable of receiving a fax) for
retrieval (print). The Play Messages Menu
plays.
The date and time the message was received
plays, followed by the entire message.
Note If your System Administrator
Future Delivery Review
While the message is
playing or immediately
after, you can press to
play the next message, to save the current
message, to delete the
current message and/or
to return to the Special
Functions Menu.
Continuous Delete
30
programmed an automatic date and time
stamp for all messages, the stamp plays
automatically at the beginning of each
message.
Stratagy ES announces the total number of
future delivery messages and plays the first
message (i.e., future delivery time/date,
destination mailbox, and the entire message)
based on chronological order. Stratagy ES
automatically saves the message for future
delivery.
Stratagy ES prompts for or entry.
Stratagy ES User Guide
01/03
Play Messages
Special Functions
Press to delete all
messages
Deletes multiple messages at one time in your
New, Saved or Personal Message Folder(s)
without additional action from you.
Note See the Continuous Play feature on page
32 before using Continuous Delete.
The number of messages deleted is based on a
preset length of time (designated in minutes) set
by your System Administrator on a system-wide
basis.
The deletion starts with the first
message in the folder and
continues until the preset time has
expired. Both heard and unheard
messages are deleted. If there are
multiple folders, the deletion
occurs only in the folder you are
in when you pressfor
continuous delete.
Returns to Play Messages Menu.
Stratagy ES checks the system for any personal
folders you have created. If personal folders
exist, Stratagy ES prompts for a personal folder
number. If none exist, this feature operates as a
toggle and moves you back and forth between
the New and Saved Message Folders.
Important!
...or to cancel option.
New/Saved message
folder (toggle)
If personal folders exist,
enter a folder number
...or to go to new
folder, to go to Saved
Message Folder, or to
return to previous menu.
Stratagy ES User Guide
01/03
31
Play Messages
Special Functions
Continuous Play
Plays many messages at a time in your New,
Saved or Personal Message Folder(s) without
additional action from you.
Note Messages played in the New Message
Folder remain as new messages and are
not automatically saved.
The number of messages played is based on a
preset length of recorded time (designated in
minutes) and therefore varies. (Your System
Administrator sets the length of time on a
system-wide basis.) The messages played are
those whose cumulative time is equal to, or less
than, the designated number of minutes.
Important! The playback starts with the first
message in the folder and
continues until the preset time has
expired. If there are multiple
folders, the playback occurs only
in the folder you are in when you
pressfor continuous playback.
Return to previous
Ask your System Administrator to verify that
you have this option.
Stratagy ES returns to the Play Messages Menu.
menu
32
Stratagy ES User Guide
01/03
Play Messages
Retrieve and Listen to E-mail Messages
Retrieve and Listen to E-mail Messages
Note This feature is only available to users of Stratagy ES with Unified Messaging
(UM) and Text-to-Speech (TTS) capabilities. Check with your System
Administrator to find out if your system is configured for this feature.
When you press (menu shown below) from the Main Menu, Stratagy ES announces
how many new e-mail messages you have, and gives you the opportunity to have them
read to you. By pressing , Stratagy ES retrieves and begins reading your e-mail
messages using an automated voice.
The order in which they are read to you, is determined by your e-mail service. In most
cases, this is in the order in which they were received.
From the Main Menu:
Retrieve and Listen to E-mail Messages
Listen to e-mail message
Replay the current e-mail message
Save the current e-mail mesage
Delete the current e-mail message
Forward the current e-mail message
Reply to the current e-mail message
Return to the Main Menu
Delete e-mail messages
Cancel deletion of e-mail messages
5453
1. From the Main Menu, press
.
2. Press to play your e-mail
messages.
Stratagy ES User Guide
01/03
The system accesses your e-mail account and
prompts you with the number of new e-mail
messages you have. The E-mail Message Menu
plays.
An e-mail message plays. The system tells you
if a attachment(s) is present. Stratagy ES can
only alert you of the presence of attachments, it
cannot administer them in any way.
33
Play Messages
Retrieve and Listen to E-mail Messages
3. (Optional) While the
message plays or
immediately after, you can
select one of the following:
Play the next e-mail
message
Skips to the beginning of the next e-mail
message.
Note If you reach the end of your e-mail
messages, pressing takes you back to
Save the current e-mail
message
Delete the current
e-mail message
the previous menu.
The e-mail message remains in your e-mail
mailbox and the E-Mail Message Menu plays.
Marks the current e-mail message for deletion
from your e-mail account. The Listen to E-mail
Message Menu plays.
If you only press and then hang
up, the message is not deleted.
You must press to exit this menu
in order for the deletion to be
complete.
Stratagy ES requests address information. After
the first destination has been entered, additional
destinations can be entered by pressing . The
destination user must have a Stratagy ES voice
mailbox with an e-mail address designated
within that mailbox.
Important!
Forward the current
e-mail message
Comments can be
recorded for this
message, which is
attached as a standard
.wav file to the original
message.
If the destination mailbox does not support
e-mail, the system informs you that this was an
invalid entry. E-mail messages cannot be
forwarded to Stratagy ES Personal or System
Distribution Lists.
Note Check with your System Administrator to
see if your mailbox is set up for this
feature.
34
Stratagy ES User Guide
01/03
Play Messages
Retrieve and Listen to E-mail Messages
Reply to the current
e-mail message
Replay the current
e-mail message
Return to Main Menu
Stratagy ES User Guide
Delete e-mail
messages that are
marked for deletion
Cancels deletion of
e-mail messages
marked for deletion
01/03
Stratagy ES creates an e-mail message with
your reply attached as a standard .wav audio file
and sent to the originator.
The current e-mail message plays from the
beginning.
Stratagy ES tells you the total number of e-mail
messages that will be deleted when you leave
this menu, and asks for confirmation.
Stratagy ES deletes all the messages you
marked for deletion and returns you to the Main
Menu.
Stratagy ES saves the messages and the E-mail
Message Menu plays.
35
Play Messages
Retrieve and Listen to E-mail Messages
36
Stratagy ES User Guide
01/03
Send Messages
4
You can record and send a message from any touchtone telephone to another
Stratagy ES user, several users, or to a personal or system distribution list.
This chapter covers:
•
•
•
•
•
•
•
Recording controls
Send a message
Forward a message
Reply to the current message
Special Delivery options
Future Delivery
Send a fax
Stratagy ES User Guide
01/03
37
Send Messages
Recording Controls
Recording Controls
While recording a message, you can pause/resume the recording or end the recording
using the following keys (shown below).
Pause/Resume
(toggle or 30 secs.)
End recording
3096
Pause/Resume (toggle or 30 seconds)
At any time while recording messages to another mailbox in the system, you can press
to pause the recording. The message resumes recording as soon as you press .
Stratagy ES prompts you with, “Begin recording... (Beep).”
If within a defined amount of time (default is 30 seconds) you do not press ,
Stratagy ES restarts another 30-second pause. If during the second 30-second pause
you:
• Do not press any key, Stratagy ES assumes you have cancelled the message and
returns to the Main Menu.
• Press , Stratagy ES returns you to the Send Messages Menu and you can send,
review or record over the message.
End Recording
After recording a message, press to end the recording.
38
Stratagy ES User Guide
01/03
Send Messages
Send a Message
Send a Message
Using the Send Messages Menu (shown below), you can record a message and send it
to single mailbox or multiple destinations (e.g., personal or system distribution list),
forward a message (with a comment), or reply to a message sent you.
From the Main Menu:
Play Messages
Forward the current message
Reply to the current message
Send Messages
While recording a message, you
can press:
Pause/Resume (toggle or 30
seconds)
End recording
Enter destination (one of the following):
Mailbox number plus
Directory plus name
Personal Distribution List (1~25)
Select from the following:
Mailbox number plus
Directory plus name
Multiple Destinations
Record
Record a message, comment, or reply.
(Press
when finished.)
Personal Distribution List (1~25)
Press
when finished.
Send and Return to Main menu
Review recording
Re-record
Append recording
Select Additional Destinations
Special Delivery Options
Set Urgent status (On/Off)
Set Private status (On/Off)
Set Return Receipt request (On/Off)
Return to previous menu
Set Future Delivery
Cancel message and select new destination
Cancel and return to Main Menu
Stratagy ES User Guide
01/03
Set the Hour (1~12)
AM
PM
Set the Minutes (0~59)
Set the Day (1~31)
Set the Month (1~12)
Set the Year (last two digits)
Return to previous menu
(message delivery time plays)
4555
39
Send Messages
Send a Message
1. From the Main Menu,
press .
2. Enter one of the following
destinations:
0DLOER[QXPEHU plus .
Press again to record a
message without playing
the user’s name.
Stratagy ES prompts you to enter the destination
(i.e., mailbox number, Personal or System
Distribution List, or Multiple Destinations).
If you entered a user’s mailbox number,
Stratagy ES plays the user’s name or mailbox
number for confirmation.
If you entered a system distribution list mailbox
number, Stratagy ES plays the list comment or
number for confirmation. Ask your System
Administrator for more information about
system lists available to you.
Note If your Stratagy ES system is designed
Directory plus the first
letters (Q=7, Z=9) of
the user’s first or last
name
with a fixed length number for your
mailbox number, do not press after
entering a mailbox number. See your
System Administrator for specific
operation of your system.
Stratagy ES plays the first match for the
combination of letters you entered.
Note See your System Administrator for
specific operation of your system.
...or the first letters of a
system distribution list
name.
Note Entry must be at least
three letters long.
Pressto select the
name as the destination,
to hear the next name,
or to cancel your
entry and re-enter.
40
Stratagy ES User Guide
01/03
Send Messages
Send a Message
plus a Personal
Distribution List
number (~).
Multiple Destinations
Stratagy ES plays the list comment or number
for confirmation. See “Manage Personal
Distribution Lists” on page 74 to create or
revise a destination (distribution) list.
You are prompted for the destinations: mailbox
number, directory and/or Personal
Distribution List.
Note If you forget to enter any destination(s),
you can press Additional Destinations
after you record your message to add
destinations (see page 42).
3. Record a message after the
tone. When finished,
press .
While recording, you can
press to pause/resume
(toggle or 30 seconds) the
recording.
4. Press again to send the
message immediately
Stratagy ES tells you that your message has
been sent and returns you to the Main Menu.
Important!
...or before sending the
message, you can use all of
the following options in
any combination as often as
desired.
Review recording
Re-record
If you pressto send your
message, you cannot use the
special recording and sending
options.
The recording plays.
The system prompts you to record at the beep.
Presswhen done.
Stratagy ES User Guide
01/03
41
Send Messages
Send a Message
Append recording
Presswhen done.
Select Additional
Destinations
Special Delivery
Options
Set Future Delivery
Cancel message and
select new destination
Cancel and Return to
the Main Menu
42
The appended recording plays after the already
recorded portion of the message. The system
prompts you to record at the beep.
Send the message to additional destinations.
(See Step 2 on page 40 for instructions.)
You can send a message as urgent, private, or
with a return receipt request. The settings may
be used in any combination and may be changed
prior to sending the message.
See “Special Delivery Options” on page 48 for
instructions on using this option.
You can have your message delivered at a future
specified time and date. See “Future Delivery”
on page 49 for instructions on using this option.
Cancels the message and returns you to Step 2
on page 40.
Cancels the message and returns you to the
Main Menu.
Stratagy ES User Guide
01/03
Send Messages
Forward a Message
Forward a Message
Any message sent to you that is not marked as Private can be forwarded to a single
destination or a personal or system distribution list. When forwarding a message,
recording a message (comment) is optional.
1. From the Play Messages
Menu, press .
2. Enter one of the following
destinations:
0DLOER[QXPEHU plus .
Press again to record a
message without playing
the user’s name.
Stratagy ES prompts you to enter the destination
(i.e., mailbox number, Personal or System
Distribution List or Multiple Destinations).
If you entered a user’s mailbox number,
Stratagy ES plays the user’s name or mailbox
number for confirmation.
If you entered a system distribution list mailbox
number, Stratagy ES plays the list comment or
number for confirmation. Ask your System
Administrator for more information about
system lists available to you.
Note If your Stratagy ES system is designed
Directory plus the first
letters (Q=7, Z=9) of
the user’s first or last
name
with a fixed length number for your
mailbox number, do not press after
entering a mailbox number. See your
System Administrator for specific
operation of your system.
Stratagy ES plays the first match for the
combination of letters you entered.
Note See your System Administrator for
specific operation of your system.
...or the first letters of a
system distribution list
name.
Note Entry must be at least
three letters long.
Stratagy ES User Guide
01/03
43
Send Messages
Forward a Message
Pressto select the
name as the destination,
to hear the next name,
or to cancel your entry
and re-enter.
plus a Personal
Distribution List
number (~).
Multiple Destinations
Stratagy ES plays the list comment or number
for confirmation. See “Manage Personal
Distribution Lists” on page 74 to create or
revise a destination (distribution) list.
You are prompted for the destinations: mailbox
number, directory and/or Personal
Distribution List.
Note If you forget to enter any destination(s),
you can press Additional Destinations
after you record your message to add
destinations (see page 45).
3. (Optional) Press to record
a message (comment) after
the tone. When finished,
press .
While recording, you can
press to pause/resume
(toggle or 30 seconds) the
recording.
4. Press again to forward
the message immediately
Stratagy ES tells you that your message has
been forwarded and returns you to the Main
Menu.
Important!
If you press to forward your
message, you cannot use the
special recording and sending
options.
...or before sending the
message, you can use any
of the following options:
44
Stratagy ES User Guide
01/03
Send Messages
Forward a Message
Review recording
Re-record
Presswhen done.
Append recording
Presswhen done.
Select Additional
Destinations
Special Delivery
Options
Set Future Delivery
Cancel message and
select new destination
Cancel and Return to
the Main Menu
Stratagy ES User Guide
01/03
The forwarding comment plays.
The system prompts you to record the comment
at the beep.
The appended forwarding comment plays after
the already recorded message comment. The
system prompts you to record at the beep.
Send the forwarded message to additional
destinations. (See Step 2 on page 43 for step-bystep instructions.) You may repeat this step as
often as necessary.
You can send a message as urgent, private, or
with a return receipt request. The settings may
be used in any combination and may be changed
prior to sending the message.
See “Special Delivery Options” on page 48 for
instructions on using this option.
You can have your message delivered at a future
specified time and date. See “Future Delivery”
on page 49 for instructions on using this option.
Cancels the message and returns you to Step 2
on page 43.
Cancels the message and returns you to the
Main Menu.
45
Send Messages
Reply to the Current Message
Reply to the Current Message
Stratagy ES lets you reply to a message that you are currently playing.
When you reply to a message sent from within a Stratagy ES user’s mailbox, you do
not have to select a destination since Stratagy ES “remembers” the source of the
message. You can send the reply to additional destinations.
If the message was not recorded from a user’s mailbox, you may still reply to the
message but you must enter the destination mailbox number.
When the originator(s) receives and plays the reply, he/she hears the prompt, “Reply
message from [name or mailbox number].”
1. From the Play Messages
Menu, press .
2. (Optional) If the message
was not recorded from a
user’s mailbox, you must
enter a destination (see Step
2 on page 40 for
instructions).
3. Record your reply after the
tone. When finished,
press .
While recording, you can
press to pause/resume
(toggle or 30 seconds) the
recording.
4. Press again to send the
reply immediately
You are prompted to record your reply to the
message.
Stratagy ES tells you that your reply has been
sent and returns you to the Main Menu.
Important!
46
If you press to send your reply
you cannot use the special
recording and sending options.
Stratagy ES User Guide
01/03
Send Messages
Reply to the Current Message
...or before sending the
message, you can use
any of the following
options:
Review recording
Re-record
Presswhen done.
Append recording
Presswhen done.
Select Additional
Destinations
Special Delivery
Options
Set Future Delivery
Cancel reply
Cancel and Return
to the Main Menu
Stratagy ES User Guide
01/03
The recording plays.
The system prompts you to record at the beep.
The appended recording plays after the already
recorded portion of the message. The system
prompts you to record at the beep.
Send the message to additional destinations.
(See Step 2 on page 40 for instructions.)
You can send a message as urgent, private, or
with a return receipt request. The settings may
be used in any combination and may be changed
prior to sending the message.
See “Special Delivery Options” on page 48 for
instructions on using this option.
You can have your message delivered at a future
specified time and date. See “Future Delivery”
on page 49 for instructions on using this option.
Cancels the reply and returns you to Step 3 on
page 46.
Cancels the message and returns you to the
Main Menu.
47
Send Messages
Special Delivery Options
Special Delivery Options
You can send a message as urgent, private, or with a return receipt request. The
settings may be used in any combination and may be changed prior to sending the
message.
When you send, forward or reply to a message, this option is available by pressing Special Delivery Options.
➤ Enter an option number:
Set Urgent status
(toggle)
To remove the urgent
status, press then again.
Set Private status
(toggle)
To remove the private
status, press then again.
Set Return Receipt
request (toggle)
To remove the return
receipt request, press then again.
Return to previous
Urgent messages play first in the New Message
Folder.
Private messages cannot be forwarded.
Stratagy ES notifies you when and by whom the
message was received and plays the original
message.
Only messages that have been deleted, saved, or
marked as Pending (if so enabled) by the
destination mailbox submit a Return Receipt
notification.
Stratagy ES returns you to the previous menu.
menu
48
Stratagy ES User Guide
01/03
Send Messages
Future Delivery
Future Delivery
Stratagy ES can be configured so that your message is delivered at a future specified
time and date. When you send, forward or reply to a message, this option is available
by pressing Set Future Delivery.
Since each of the settings default to the current time/date, you do not need to enter all
the options. For example, if you have recorded a message and want to have it
delivered that afternoon at 2:30 p.m., you only need to enter the hour (2), select p.m.
and enter the minutes (30) using options 1 and 2.
After marking the message for future delivery, you can review (play, save, delete) the
message at any time before it is sent. See Chapter 3 – Play Messages for instructions
on using the Future Delivery Review option.
➤ Enter an option number and
press .
Set Hour (~)
AM
PM
Set Minutes (~)
Set Day (~)
Set Month (~)
Set Year (two or four
digits)
Return to previous
menu
Stratagy ES prompts you to select a.m. or p.m.
Two-digit numbers less than the last two digits
of the current year are set for the twenty-first
century. For example, enter to set 2001.
Stratagy ES plays the message delivery time
and date and returns you to the previous menu.
Note Once the message has been sent, you can
review, continue to send (save), or delete
this message using the Future Delivery
Review option on the Play Messages
Menu. (See Chapter 3 – Play Messages.)
Stratagy ES User Guide
01/03
49
Send Messages
Send a Direct Fax
Send a Direct Fax
Stratagy ES enables you to send a fax to a mailbox when you are calling from a fax
machine handset.
1. Put the document to be
faxed into the fax machine.
2. From the fax machine
handset, dial the number for
Stratagy ES.
3. Press .
4. Enter the destination
mailbox. Finish by pressing
.
5. (Optional) Press to record
a comment.
Begin recording at the tone.
Finish by pressing .
After recording, you can
press:
Review comment
Re-record
Press when done.
Append recording
Presswhen done.
Cancel recording
Save recording
50
The company greeting plays.
The system prompts you to enter the destination
mailbox for your fax.
Stratagy ES prompts you to record a comment,
enter an additional destination or send the fax.
The system prompts you to record at the beep.
The complete comment plays.
The system prompts you to record at the beep.
The appended comment plays after the already
recorded portion. The system prompts you to
record at the beep.
The comment is canceled. The system returns to
the previous menu.
Stratagy ES tells you that the comment has been
recorded and returns to the previous menu.
Stratagy ES User Guide
01/03
Send Messages
Send a Direct Fax
6. (Optional) Press Additional Destinations.
7. Press the 6WDUW key on the
fax machine and hang up
the handset.
Stratagy ES User Guide
01/03
Send the message to additional destinations.
(See Step 2 on page 43 for step-by-step
instructions.) You can repeat this step as often as
necessary.
The fax is processed and sent to the destination
mailbox(es).
51
Send Messages
Send a Direct Fax
52
Stratagy ES User Guide
01/03
5
Manage Mailbox
Stratagy ES provides special options to customize and manage your mailbox features
(menu shown below).
From the Main Menu:
Manage Mailbox
Change Greeting
Change User Options
Manage Personal Distribution Lists
Manage Guest Mailboxes
Manage Personal Folders
Return to Main Menu
4576
Stratagy ES User Guide
01/03
53
Manage Mailbox
Change Greeting
Change Greeting
You can select either a personal or system greeting to play callers when you do not
answer or when your telephone is busy.
This section discusses the three basic greeting controls (menu shown below):
• Create or record over a personal greeting
• Select a personal greeting
• Review a personal greeting
From the Main Menu:
Manage Mailbox
From the Manage Mailbox Menu:
Change Greeting
~
Select a Personal Greeting
Select System Greeting
Review selected greeting
Record (new) greeting
Review recording
Re-record
Append recording
Cancel recording
Save recording
Return to previous menu
Review current greeting
Return to previous menu
4550
54
Stratagy ES User Guide
01/03
Manage Mailbox
Change Greeting
Create or Record Over a Personal Greeting
Personal greetings should be informative and advise callers when you will be
available to return their calls or respond to their messages. You can prerecord
greetings for the days of the week when you are out of the office or on vacation. You
can update personal greetings as often as you want.
You can record and store up to seven different recorded greetings from which you can
select as your personal greeting. The System Administrator can also schedule your
greetings to play automatically at different times.
1. From the Manage Mailbox
Menu, press .
2. Enter a number from ~.
3. Press to record the
greeting (speak slowly and
clearly). Press when
done.
Stratagy ES plays the Change Greeting options.
Your greeting is identified by the number
chosen. For example, you can record a general
greeting as greeting 1, then record a greeting for
holidays as greeting 2. Later, you can choose
which one plays. You can re-record a greeting at
any time.
The following information should be included
in your Personal Greeting:
•
•
•
•
•
•
Your name
Company and/or department
Date
Your availability
Instructions to leave a detailed message
Call coverage options
Sample Greeting
“Hi. This is Mary Smith of the Toshiba
Marketing Department. It is Monday, June 19,
and I am in the office today. I am either on the
telephone or have stepped away for a few
minutes and your call has been forwarded to my
voice mailbox. If at the tone you leave a detailed
message and a telephone number where I can
reach you, I will be happy to return your call.”
Stratagy ES User Guide
01/03
55
Manage Mailbox
Change Greeting
4. (Optional) After recording,
you can press:
Review recording
Re-record
Press when done.
Append recording
Press when done.
Cancel recording
Save recording
5. Press to return to the
previous menu.
6. Press and select another
greeting number (~).
7. Repeat Step 3 on page 55
for any additional greetings
you want to record.
8. To return to the Main
Menu, press .
56
You can repeat options 1~3 as many times as
you wish.
The complete greeting plays.
The system prompts you to record at the beep.
Appending a greeting enables you to add
information to the end of your already recorded
greeting. The system prompts you to record at
the beep.
The greeting is canceled. The system returns to
the previous menu.
Stratagy ES tells you that greeting (number) has
been recorded and returns to the previous menu.
Again, you are given the option to review or
record over the greeting you have just recorded.
You are given the option to record another
greeting.
The last greeting selected or
recorded is the greeting that
callers hear as your mailbox
greeting.
Stratagy ES plays the Main Menu options.
Important!
Stratagy ES User Guide
01/03
Manage Mailbox
Change Greeting
Select a Personal Greeting
1. From the Manage Mailbox
Menu, press .
2. Enter a personal greeting
number (~)
...or to select the system
greeting.
Stratagy ES plays the Change Greeting options.
Your callers hear the selected greeting when you
do not answer or when your telephone is busy.
Your callers hear the system greeting when you
do not answer or when your telephone is busy.
Note If you have recorded a busy greeting, this
greeting does not play when your
telephone is busy (see “Select Busy
Greeting” on page 63 for details).
The last greeting selected or
recorded is the greeting that
callers hear as your mailbox
greeting.
The current greeting plays.
Important!
...or to review the current
greeting.
3. Press to return to the
previous menu
...or to return to the
Manage Mailbox Menu
...or to return to the
Main Menu.
Stratagy ES User Guide
01/03
Stratagy ES returns to the previous menu.
The Manage Mailbox Menu plays.
The Main Menu plays.
57
Manage Mailbox
Change Greeting
Review a Personal Greeting
1. From the Manage Mailbox
Menu, press .
2. Press to review the
current greeting
Stratagy ES plays the Change Greeting options.
The current greeting plays. Stratagy ES prompts
you with the Change Greeting Menu options.
Note Pressing does not affect the current
...or enter a number from
~, then press to review
the greeting.
3. Press to return to the
previous menu
...or to return to the
Manage Mailbox Menu
...or to return to the
Main Menu.
58
greeting selection.
The greeting plays. Stratagy ES prompts you
with the Change Greeting Menu options.
Stratagy ES returns to the previous menu.
The Manage Mailbox Menu plays.
The Main Menu plays.
Stratagy ES User Guide
01/03
Manage Mailbox
Change User Options
Change User Options
Stratagy ES provides a number of special options to improve time management and
productivity (menu shown below). For example, the DND feature can provide blocks
of time for meetings or projects uninterrupted by the ringing of a telephone.
From the Main Menu:
Manage Mailbox
From the Manage Mailbox Menu:
Change User Options
Change Do Not Disturb (On/Off)
Change Call Screening (On/Off)
Change Security Code
Select Busy Greeting (toggle)
Record Busy Greeting
Record your Name
Change message Notification
Set Automatic Message Copy
Review Option Settings
Return to previous menu
4553
Important!
• If you do not hear all the options for this menu, they may not be configured for your
mailbox or system. Please ask your System Administrator to verify which user
options are available to you.
• If the DND, Call Screening or busy greeting features do not function after you have
enabled them, contact your System Administrator. These features can only operate
if Stratagy ES performs as the Automated Attendant (AA) and your telephone
system or telephone may be performing that function instead.
Stratagy ES User Guide
01/03
59
Manage Mailbox
Change User Options
Change Do Not Disturb (DND) Setting
If you set this feature to On, Stratagy ES automatically sends calls to your mailbox
without first ringing your telephone. The System Administrator can also set this
feature to turn On or Off automatically at pre-scheduled times and/or days of the
week.
1. From the Manage Mailbox
Menu, press .
2. Press .
Stratagy ES plays the Change User Options
Menu.
A prompt verifies the current status (On/Off) of
the DND feature.
DND on the Stratagy ES voice
processing system is different
from the DND features for your
telephone system. If your
telephone comes with a DND
button or feature, it works
independently from this feature on
Stratagy ES.
Pressing toggles the DND feature On and Off.
Important!
3. (Optional) Press again to
reset the feature, if
required.
4. Press to return to the
Manage Mailbox Menu
...or to return to the
Main Menu.
60
You can select another user Manage Mailbox
option.
You can select another Main Menu option.
Stratagy ES User Guide
01/03
Manage Mailbox
Change User Options
Change Call Screening Setting
If you set this feature to On, Stratagy ES asks callers for their name and company.
Without the caller’s knowledge, the system relays that information to you and
provides you with special options to handle the call (menu shown below).
Receive the call
Reject the call and let the call forward
to your mailbox
Transfer the call to another extension
with an announcement
Transfer the call to another extension
without an announcement
The System Administrator can also set this feature to turn On or Off automatically at
pre-scheduled times and/or days of the week.
1. From the Manage Mailbox
Menu, press .
2. Press .
3. (Optional) Press again to
reset the feature, if
required.
4. Press to return to the
Manage Mailbox Menu
...or to return to the
Main Menu.
Stratagy ES User Guide
01/03
Stratagy ES plays the Change User Options
Menu.
A prompt verifies the current status (On/Off) of
the Call Screening feature.
Pressing toggles the Call Screening feature
On and Off.
You can select another user Manage Mailbox
option.
You can select another Main Menu option.
61
Manage Mailbox
Change User Options
Change Security Code
Each mailbox in the system has a security code. The code must be entered by you in
order to “log on” to your mailbox, enabling you to access your messages, settings,
greetings, etc.
Note You can change your security code as often as you wish to ensure the privacy of
your messages and personal greetings.
1. From the Manage Mailbox
Menu, press .
2. Press .
3. Enter your new security
code + .
4. Re-enter your new security
code + .
62
Stratagy ES plays the Change User Options
Menu.
Stratagy ES prompts you to enter your new
security code and notifies you of the number of
allowable digits.
For example, Stratagy ES might prompt “the
new security code must have at least 3 digits
and 16 maximum digits” or “the new security
code must be exactly 4 digits.”
Stratagy ES prompts you to re-enter your new
security code for verification.
After entering the security code a second time,
Stratagy ES announces that your security code
has been changed.
Stratagy ES User Guide
01/03
Manage Mailbox
Change User Options
Select Busy Greeting
1. From the Manage Mailbox
Menu, press .
2. Press.
3. (Optional) Press again to
reset the feature, if
required.
Stratagy ES plays the Change User Options
Menu.
A prompt verifies the current status (custom/
system) of the Busy Greeting feature.
Pressing toggles between selecting your
custom busy greeting and the system busy
greeting.
Note The custom busy greeting must be
4. Press to return to the
Manage Mailbox Menu
...or to return to the
Main Menu.
Stratagy ES User Guide
01/03
recorded before it can be selected (see
“Create or Record Over Busy Greeting”
on page 64).
You can select another user Manage Mailbox
option.
You can select another Main Menu option.
63
Manage Mailbox
Change User Options
Create or Record Over Busy Greeting
You can record your own custom busy greeting (menu shown below) that plays when
callers reach your extension and it is busy. While your callers are listening to the busy
greeting, they can enter a different mailbox number, press to hold (if configured for
your mailbox by the System Administrator), or remain on the line to leave a message.
From the Change User Options Menu:
Record Busy Greeting
Record a greeting
Press
when done.
Review recording
Re-record
Append recording
Cancel recording
Save recording
4556
Note Depending on the configuration of your telephone and telephone system,
Stratagy ES may not receive a busy tone when callers reach your extension. If
Stratagy ES doesn’t receive a busy tone, your selected personal greeting plays
instead.
If a custom greeting is not recorded, the default system busy greeting plays.
64
Stratagy ES User Guide
01/03
Manage Mailbox
Change User Options
1. From the Manage Mailbox
Menu, press .
2. Press.
3. Begin recording at the tone.
Press when done.
4. (Optional) After recording,
you can press:
Review greeting
Re-record
Begin recording at the
tone. Press when
done.
Append recording
Begin recording at the
tone. Presswhen
done.
Cancel recording
Save recording
5. Press to return to the
Manage Mailbox Menu
...or to return to the
Main Menu.
Stratagy ES User Guide
01/03
Stratagy ES plays the Change User Options
Menu.
Stratagy ES prompts you to record your custom
busy greeting.
Sample Greeting:
“Thanks for calling. I’m currently on the phone.
If you would like to hold, press star, or you can
leave me a message after the tone.”
The complete greeting plays.
The system prompts you to record at the beep.
The appended greeting plays after the already
recorded portion of the greeting. The system
prompts you to record at the beep.
The greeting is canceled. The system returns to
the previous menu.
Stratagy ES tells you that the greeting has been
recorded and returns to the previous menu.
You can select another user Manage Mailbox
option.
You can select another Main Menu option.
65
Manage Mailbox
Change User Options
Record Your Name
Your name is announced whenever the directory is accessed, you select the system
greeting, or a message is sent by another Stratagy ES user.
Stratagy ES prompts you through the entire recording sequence (menu shown below).
You can re-record your name at any time simply by repeating these steps.
From the Change User Options Menu:
Record your Name
Record your name and
press
when done.
Review recording
Re-record
Append recording
Cancel recording
Save recording
4557
Note Some Stratagy ES systems may not be configured to play your name when you
log on to your mailbox.
66
Stratagy ES User Guide
01/03
Manage Mailbox
Change User Options
1. From the Manage Mailbox
Menu, press .
2. Press .
3. At the tone, state your name
slowly and clearly.
Press when done.
4. (Optional) After recording,
you can press:
Review recording
Re-record
Press when done.
Append recording
Press when done.
Cancel recording
Save recording
Stratagy ES plays the Change User Options
Menu.
Stratagy ES prompts you to record your name.
Your newly recorded name plays.
You can re-record your name as often as you
wish.
You can add a short comment that plays at the
end of the recording (for example, a vacation
announcement).
You can cancel your newly recorded name (and
extension) and return to the previous menu.
Stratagy ES confirms that your name has been
recorded. Stratagy ES returns to the previous
menu.
When your mailbox is accessed, you can select
either the system or personal greeting to play.
See Chapter 5 – Manage Mailbox for
instructions on selecting and creating greetings.
Stratagy ES User Guide
01/03
67
Manage Mailbox
Change User Options
Change Message Notification
Your mailbox can have notification records programmed by the System Administrator
with a specific notification method (message waiting lights, pagers, voice, etc.) and
the time/day when that notification record applies. The repeat count (how many times
the notification is attempted) and interval for retrying the notification is also set.
Once you have enabled a notification record by entering the template number (menu
shown below), Stratagy ES automatically performs the chosen notification method.
The Stratagy ES enables you to change digits that a notification may use in an attempt
to notify you of a message. These digits could be the number where you can be
reached, your paging service, or the number that displays in a digital pager’s LCD
screen. It depends on how the notification event has been programmed.
From the Change User Options Menu:
Change message Notification
Enter notification template number
or enter
for a list of templates
Enable/Disable notification template
(toggle)
Change notification digits
Save changes
Return to previous menu
4558
1. From the Manage Mailbox
Menu, press .
2. Press.
3. Enter the notification
template number
68
Stratagy ES plays the Change User Options
Menu.
You are told the number of notification records
you have and are prompted to enter the
notification record number.
Stratagy ES confirms the template number,
either speaks or spells the template title, states
whether the template is enabled or disabled, and
tells you the phone number (if applicable).
Stratagy ES User Guide
01/03
Manage Mailbox
Change User Options
...or if you do not
remember the template
number you want, press
.
Press to select the
notification template or to hear the next record.
4. Press an option number:
Enable/disable
notification template
(toggle)
Change notification
digits
Enter the new
notification digits and
press .
Save changes
Return to previous
menu
5. Press to return to the
Manage Mailbox Menu
...or to return to the
Main Menu.
Stratagy ES User Guide
01/03
The system plays a template header record for
each notification template consisting of the
template number and title (e.g., CTX message
light on). After each header record plays, you
are asked to select the record or hear the next
record.
Pressing toggles the notification template
between Enable and Disable. After pressing , a
prompt verifies the current status.
Stratagy ES verifies the number entered.
Stratagy ES tells you that the notification
template changes have been recorded.
Stratagy ES returns to the previous menu.
Stratagy ES cancels the change message
notification options and returns to the previous
menu.
You can select another user Manage Mailbox
option.
You can select another Main Menu option.
69
Manage Mailbox
Change User Options
Set Automatic Message Copy
When enabled, the Automatic Message Copy feature (menu shown below)
automatically copies messages from your mailbox to a designated mailbox.
You can choose to copy all your messages or only the messages marked urgent,
designate the mailbox destination for the copies, and set the time of day for copying
the messages that arrive at your mailbox. You can also set a time delay, if one is
needed.
From the Change User Options Menu:
Enable/Disable copy (toggle)
Set Automatic Message Copy
Enter copy Destination
Copy All Messages
Copy Urgent Messages
Confirm
Return to previous menu
Re-enter
4559
Cancel and return to
previous menu
Set Delay Time
Set Hour
Set Minutes
Set Day
Save changes and return to
previous menu
Set copy Start Time
Set Hour
AM
PM
Set Minutes
Return to previous menu
Set copy End Time
Set Hour
AM
PM
Set Minutes
Return to previous menu
Save changes and return to
previous menu
Return to previous menu
70
Stratagy ES User Guide
01/03
Manage Mailbox
Change User Options
1. From the Manage Mailbox
Menu, press .
2. Press .
3. Press to copy all
messages
...or to copy only urgent
messages
...or to return to previous
menu.
4. (Optional) You can select
all of the following options
in any combination:
Enable/Disable (toggle)
Enter message
destination
Press to confirm the
number, to erase and
re-enter, or to cancel
and return to previous
menu.
Stratagy ES User Guide
01/03
Stratagy ES plays the Change User Options
Menu.
Stratagy ES plays the Automatic Message Copy
Menu.
Stratagy ES confirms the automatic message
copy for all messages is enabled/disabled, the
mailbox where the message will be copied,
delay time, and auto copying starting/ending
times.
Stratagy ES confirms the automatic message
copy for urgent messages is enabled/disabled,
the mailbox where the message will be copied,
delay time, and auto copying starting/ending
times.
Stratagy ES returns to the previous menu.
Pressing toggles the message copy feature On/
Off.
A prompt verifies the mailbox number and
prompts you for an entry of , or .
Pressing saves the mailbox number.
71
Manage Mailbox
Change User Options
Set delay time
Select one of the
following:
Set hour
Set minutes
Set day
Returns to previous
menu
Set Copy Start Time.
Enter an option number
and press .
Set Hour (~)
AM
PM
Set Minutes (~)
Set Copy End Time.
Enter an option number
and press .
Set Hour (~)
AM
PM
Set Minutes (~)
72
Stratagy ES prompts you to enter the time.
Only one of the following entries are allowed.
System prompts for number of hours to delay
message (maximum is 24 hours). Once you
have entered the value, Stratagy ES saves the
entry and returns to the previous menu.
System prompts for number of minutes to delay
message (maximum is 60 minutes). Once you
have entered the value, Stratagy ES saves the
entry and returns to the previous menu.
System prompts for number of days to delay
message (maximum is 25 days). Once you have
entered the value, Stratagy ES saves the entry
and returns to the previous menu.
Saves current entry and returns to the auto copy
message.
Stratagy ES prompts you to enter the time.
Stratagy ES prompts you to select AM or PM.
Stratagy ES prompts you to enter the time.
Stratagy ES prompts you to select AM or PM.
Stratagy ES User Guide
01/03
Manage Mailbox
Change User Options
Saves changes and
returns to previous
menu.
Cancel changes and
returns to previous
menu.
Return to the Manage
Mailbox Menu
...or to return to
Main Menu.
Saves the changes and returns to the auto copy
message.
Cancels changes and returns to the auto copy
message.
You can select another user Manage Mailbox
option.
You can select another Main Menu option.
Review Option Settings
1. From the Manage Mailbox
Menu, press .
2. Press to Review your
Option Settings.
3. Press to return to the
Manage Mailbox Menu
...or to return to the
Main Menu.
Stratagy ES User Guide
01/03
Stratagy ES plays the Change User Options
Menu.
Stratagy ES verifies the status of your DND,
Call Screening options and plays your selected
busy message and name recording.
You can select another user Manage Mailbox
option.
You can select another Main Menu option.
73
Manage Mailbox
Manage Personal Distribution Lists
Manage Personal Distribution Lists
The Manage Personal Distribution Lists feature enables you to create and manage up
to 25 personal distribution lists. The lists consist of the mailboxes to which you most
frequently send messages.
At the time you create a list, you are given the option of recording a “list comment”
that serves as the title or name for the list. The comment plays each time you use the
list to confirm that you have chosen the correct distribution list.
From the Manage Personal Distribution Lists Menu (shown below), you can review
the list contents, add and delete mailboxes to the list, and record a list comment.
From the Main Menu:
Manage Mailbox
From the Manage Mailbox Menu:
Manage Personal Distribution Lists
Select ~ for a Personal Distribution Lists
Review current list
Add a mailbox to the list
Delete a mailbox from the list
Record a list Comment
Return to previous menu
Return to previous menu
1. From the Manage Mailbox
Menu, press .
2. Select the desired list
number ~.
3. After selecting a list, you
can press:
Review your current list
Add a Mailbox to the
list
74
Stratagy ES plays the Manage Personal Lists
options.
The system prompts you with the name (and
extension) of each mailbox on the list.
Stratagy ES prompts you to enter the mailbox
number.
Stratagy ES User Guide
01/03
Manage Mailbox
Manage Personal Distribution Lists
Enter the mailbox
number or press for
Stratagy ES directory
assistance. Press when
done.
Delete a Mailbox from
the list
Enter the mailbox
number or press for
Stratagy ES directory
assistance. Press when
done.
Record a list Comment
Record your comment.
Press when done.
(Optional) After
recording, you can press
to review recording, to rerecord, to append
the recording, to
cancel the recording or
to save the recording
and return to the
previous menu.
4. Press to return to the
previous menu
...or to return to the
Manage Mailbox Menu
...or to return to the
Main Menu.
Stratagy ES User Guide
01/03
The name (and extension) plays. You can add
additional mailbox numbers as needed.
Stratagy ES prompts you to enter the mailbox
number.
The name (and extension) plays. The system
prompts “Deleted.”
When sending a message, the comment plays
each time the destination list is selected.
Stratagy ES prompts you to record the
comment.
Stratagy ES returns to the previous menu.
You can select another Manage Mailbox option.
You can select another Main Menu option.
75
Manage Mailbox
Manage Guest Mailboxes
Manage Guest Mailboxes
Guest mailboxes provide limited access to the Stratagy ES system for temporary and
project-oriented employees, such as consultants and contractors. Guest users may only
send and receive messages to their host and other guests that share the same host
mailbox.
The Guest mailboxes are selected from a system-generated list and assigned on a peruse basis. See your System Administrator for details if you have this feature.
Managing guest mailboxes entails creating and deleting guest mailboxes and resetting
a guest password (menu shown below).
From the Main Menu:
Manage Mailbox
From the Manage Mailbox Menu:
Manage Guest Mailboxes
Create a Guest Mailbox
Delete a Guest Mailbox
Review your Guest Mailboxes
Reset Guest Password
Return to previous menu
4560
1. From the Manage Mailbox
Menu, press .
2. Select one of the following:
Create a Guest Mailbox
Delete a Guest Mailbox
Enter the mailbox
number. Press when
done.
76
Stratagy ES plays the Manage Guest Mailboxes
options.
The system prompts with a Guest Mailbox
number. Be sure to make a note of the number
and the person you assign.
Stratagy ES prompts you to enter the mailbox
number.
The system confirms the Guest Mailbox is
deleted.
Stratagy ES User Guide
01/03
Manage Mailbox
Use Guest Mailboxes
Review your Guest
Mailboxes
Reset Guest Password
Enter the mailbox
number.
3. Press to return to the
Manage Mailbox Menu
...or to return to the
Main Menu.
The system lists your Guest Mailbox numbers.
Stratagy ES prompts you to enter the mailbox
number.
Stratagy ES resets the password for the guest
mailbox.
You can select another user Manage Mailbox
option.
You can select another Main Menu option.
Use Guest Mailboxes
A guest user can access his/her mailbox in the same manner as a regular Stratagy ES
user. The guest can play and send messages but is denied access to all Manage
Mailbox Menu features except “ Change Security Code” and “ Record your
Name.”
Note See “Access Your Mailbox” on page 18 for instructions on accessing the guest
mailbox.
Stratagy ES User Guide
01/03
77
Manage Mailbox
Manage Personal Folders
Manage Personal Folders
Your messages can reside in up to nine folders—one new, one saved and seven
personal folders created by you for the purpose of saving your messages. The personal
folders are for only your use.
At the time you create a folder, you are given the option of recording a “name/
comment” that serves as the title or name for the folder (menu shown below). The
comment plays each time you use the folder to confirm that you have chosen the
correct one.
When you access your mailbox, Stratagy ES announces that you have “x number of
new messages and x number of saved messages.” When you press from the Play
Messages menu to save a message, Stratagy ES plays the folder number and the
recorded name/comment of each of the available folders.
You are requested to enter a valid folder number where you want the message saved. If
an invalid number is entered, Stratagy ES automatically saves the message in folder (i.e., standard save folder).
From the Main Menu:
Manage Mailbox
From the Manage Mailbox Menu:
Manage Personal Folders
Select ~ for a Personal Folder
Review folder name/comment
Record folder name/comment
Review recording
Re-record a folder Comment
Append a folder Comment
Cancel recording
Save recording and return to previous
menu
Return to previous menu
78
Stratagy ES User Guide
01/03
Manage Mailbox
Manage Personal Folders
1. From the Manage Mailbox
Menu, press .
2. Enter a number from ~.
3. After selecting a folder, you
can press:
Review folder name/
comment
Record the name and
comment
At the tone, state the
folder name and
comment slowly and
clearly. Press when
done.
4. (Optional) After recording,
you can press:
Review recording
Stratagy ES plays the Manage Personal Folders
options.
Number 1 is reserved for the standard save
folder and cannot be used.
The system plays the folder name and comment.
Re-record
Press when done.
The newly recorded folder name/comment
plays.
You can re-record the folder name/comment as
often as you wish.
Append recording
Press when done.
You can add a short comment that plays at the
end of the original comment.
Cancel recording
You can cancel your newly recorded folder
name/comment and return to the previous menu.
Stratagy ES confirms that the folder name/
comment has been recorded. Stratagy ES returns
to the Manage Personal Folders menu.
Save recording
Stratagy ES User Guide
01/03
79
Manage Mailbox
Manage Personal Folders
5. Press to return to the
previous menu
...or to return to the
Manage Mailbox Menu
...or to return to the
Main Menu.
80
Stratagy ES returns to the previous menu.
You can select another Manage Mailbox option.
You can select another Main Menu option.
Stratagy ES User Guide
01/03
Using Stratagy ES with a
Strata CTX
A
This appendix covers the use of Stratagy ES voice mail with the Strata CTX. Call
Forward, Message Waiting, Toshiba Proprietary Integration, Direct Transfer to Voice
Mail and Voice Mail Conference features are all described.
Note Check with your System Administrator about your company’s phone system
and telephones.
Call Forward
Note See Strata CTX 3000/2000-series Telephone User Guide for additional
information on programming and using this feature on your phone.
There are two types of Call Forwarding: System and Station.
• System Call Forward (which is set in Programming) automatically directs calls to a
predefined location, such as Voice Mail.
• Station Call Forward enables you to assign Call Forward destinations for each
extension on your phone. Each extension can be independently set for a different
Call Forward feature. You can set a flexible button to perform any Call Forward
function.
Call Forward must be set prior to receiving the call.
Note Station Call Forward takes priority over System Call Forward.
Table 1 on page 82 contains the Call Forward Button sequences for performing Call
Forward. There are two ways to perform each Call Forward function. One, enter the
button sequence as described, or two, program a flexible button to perform the
sequence.
Stratagy ES User Guide
01/03
81
Using Stratagy ES with a Strata CTX
Call Forward
➤ To use the Call Forward button sequence
➤ Follow the instructions in Table 1 below shown under “Button Sequence.” Some
features require additional input, such as:
• Destination – If the destination is an outside number, press after entering the
destination. The CTX accepts destination numbers of up to 32 digits.
• Timer – This is a two digit entry representing how long (8 to 160 seconds) your
telephone should ring before forwarding the call. If you enter one digit, you
must press after entering the single digit.
Also, in the following table, (Tone) means that a confirmation tone plays at that point
in the sequence.
Table 1
Call Forward Procedures
Feature
Button Sequence
Call Forward - Station
Call Forward Any Call (Internal and Incoming Line)
All Call
Press Extension button + (Tone) + Destination No. (Tone)
Busy
Press Extension button + (Tone) + Dest. No. (Tone)
No Answer
Press Extension button + (Tone) + Dest. No. (Tone) + Timer + Busy No Answer
Press Extension button + + Dest. No. + Timer + Cancel
Press Extension button + (Tone)
Call Forward - System
Call Forward - Incoming Line Calls
All Calls
Extension button + (Tone) + Dest. No. (Tone)
Busy
Extension button + (Tone) + Dest. No. (Tone)
No Answer
Extension button + + Dest. No. (Tone) + Timer (Tone) + Busy No Answer
Extension button + + Dest. No. (Tone) + Timer (Tone) + Cancel
Extension button + (Tone)
Call Forward - System
82
Activate
(Tone)
Cancel
(Tone)
Stratagy ES User Guide
01/03
Using Stratagy ES with a Strata CTX
Message Waiting
Message Waiting
Use your 0VJLED/button and LCD to see/retrieve message(s).
An extension can receive up to four simultaneous Message Waiting indications and
LCD messages. One message is reserved for the Message Center.
Your phone can be programmed to have up to four additional (flexible) Message
Waiting buttons/LEDs. Ask if these buttons have been programmed on your phone. If
so, substitute them when the 0VJ button/LED is mentioned in the following steps.
Responding to a Lit Msg LED
1. On an LCD phone, if you see a “+” press 6FUROO to display additional messages;
otherwise, go to Step 2. The “+” indicates additional messages. The LCD can show
up to three station messages for your extension and three for each additional
(phantom) extension that you may have.
2. Press 0VJ, then lift the handset. Your phone rings the extension or voice mail
device that sent the indication. The LED continues to flash red.
3. After answering the message(s), place the handset back on-hook.
4. If the Msg LED continues to flash, you have more messages; repeat Steps 1~3
above to retrieve them. Voice mail devices turn off the LED/LCD indications after
a short delay, after you checked all messages.
5. To manually turn off your Msg LED, press your extension button, then press
. Do this step for each message received.
Stratagy ES User Guide
01/03
83
Using Stratagy ES with a Strata CTX
Toshiba Proprietary Integration
Turning On/Off Message Waiting LED on Another
Extension
If you call an extension and it’s busy or there is no answer, you can light that
extension’s Message Waiting LED and enable that extension to call you back.
1. Dial an internal extension. You hear busy tone or there’s no answer.
2. Press 0VJ or . The Msg LED flashes red on the called phone. At your phone, the
Msg LED lights steady red and the LCD shows the station number where you set a
Message Waiting light.
3. Press 6SNU. Your Msg LED turns Off. The Msg LED on the called telephone
flashes until the called party presses the flashing 0VJ button - which calls you
back.
4. To turn Off a Message LED that you have set on another extension, press plus
the extension number that has the message light set. Then hang up to release your
telephone.
Toshiba Proprietary Integration
If your company’s Toshiba Strata CTX phone system has the Proprietary Integration
with your Stratagy ES enabled, you have two additional features at your disposal—
Soft Key Control of Voice Mail and Call Record to Voice Mail. If you cannot access
these features, check with your System Administrator.
Soft Key Control of Voice Mail
If you have a Strata 3000 or 2000-series digital phone equipped with a Liquid Crystal
Display (LCD), many standard functions of the Stratagy ES voice mail system can be
displayed on the digital telephone LCD and operated by Soft Keys. Feature prompting
makes voice mail functions easy to use via visual displays on the telephone in place of
listening to voice prompts over the handset, although the Stratagy ES voice prompts
still play when soft keys are used.
Note For general information on using Soft Keys on your phone, please see the
Strata CTX DKT3000/2000-Series Telephone User Guide.
84
Stratagy ES User Guide
01/03
Using Stratagy ES with a Strata CTX
Toshiba Proprietary Integration
When your telephone is idle, and a message
arrives for an extension on your phone, the Msg
LED is activated for the appropriate extension and
updates the LCD with this display (shown right).
If urgent messages are in the extension’s mailbox,
the SAVED display is replaced with the number of
URGENT messages.
Mode
Feature
1 NEW/5 SAVED
Page
Scroll
DIRECT SS
SYSTEM SD
PERSONAL SD
EXTERNAL DIR
INTERNAL DIR
5951
Soft Keys
Soft Keys
Once connected to your Stratagy ES voice
mailbox, the LCD displays the Stratagy ES Main
Menu options (shown at right). See Table 2 on
page 86 below for a list of Main Menu soft keys.
Mode
VOICE MAIL MAIN MENU
Page
Feature
Scroll
3 NEW / 2 SAVED
SEND
PLAY MSGS
MANAGE MBX
HANGUP
EXIT
5951
Soft Keys
Soft Keys
You are then able to perform many of the standard
Stratagy ES voice mail functions using the Soft
Keys on your phone (Play Messages menu
example shown at right). See Table 3 on page 86
for a list of Soft Keys.
Mode
Page
Feature
FRM: 5555
Scroll
MSG LENGTH: 00:54
NEXT
REPLAY
SAVE
PREVIOUS
DELETE
FORWARD
SPL FUNCT
BACKUP
PAUSE PLAY
GO FORWARD
PREV MENU
5953
Soft Keys
Stratagy ES User Guide
01/03
Soft Keys
85
Using Stratagy ES with a Strata CTX
Toshiba Proprietary Integration
Table 2
Stratagy ES Main Menu Soft Keys for CTX Digital Telephones
DKT 3014 SDL
DKT 3010 SD
DKT 3020 SD
DKT 2010 SD
DKT 2020 SD
PLAY MSGS
PLAY
PLAY
Play Messages
SEND
SEND
SEND
Send Messages
MANAGE MBX
MGMT
MGMT
Manage Mailbox
EXIT
Exit Mailbox
HANGUP
Table 3
QUIT
Disconnect from Stratagy ES
Soft Keys for CTX Digital Telephones
DKT 3014 SDL
DKT 3010 SD
DKT 3020 SD
DKT 2010 SD
DKT 2020 SD
ADD
ADD
ADD
ADD DESTS
ADD MBX
Voice Mail Functions
Confirm automatic copy destination
ACCEPT
Create a Guest Mailbox
Additional Destinations
ADD
ADD
Add a mailbox to the list
ALL MSGS
Copy All Messages
AM?
AM
APPEND
APND
Append recording
AUTO COPY
Set Automatic Msg Copy
BACK UP
Backup (rewind)
BSY GRT REC
Record Busy Greeting
BUSY GREET
Select Busy Greeting (toggle)
CALL SCREEN
Change Call Screening (On/Off)
CANCEL
Cancel recording
CANCEL MSG
CANC
CNCL
CHG
GREETING
Cancel message and select new
destination
Change notification digits
CHANGE
86
Voice Mail Functions
GRT
GRT
Change Greeting
Stratagy ES User Guide
01/03
Using Stratagy ES with a Strata CTX
Toshiba Proprietary Integration
Table 3
Soft Keys for CTX Digital Telephones (continued)
DKT 3014 SDL
DKT 3010 SD
DKT 3020 SD
DKT 2010 SD
DKT 2020 SD
Voice Mail Functions
CONT DELETE
Continuous Delete
CONT PLAY
Continuous Play
DATE & TIME
DATE
Message Date and Time
Set Delay Time
DELAY TIME
DELETE
DEL
DEL
Delete the message/guest mailbox
DELETE MBX
DEL
DEL
Delete a mailbox from the personal
distribution list
DELETE MSG
Delete message (Future Delivery Review)
DESTINATION
Enter automatic copy destination
DIRECTORY
DIR
DIR
Directory plus name
DND
DND
DND
Change Do Not Disturb (On/Off)
Enable/Disable:
ENABLE/
DISABLE
END TIME
•
Notification template (toggle)
•
Automatic copy
Set copy End Time
FOLDERS
FLDR
FORWARD
FWD
New/Saved message folder
FWD
Forward the current message
FUTURE DLVR
Set Future Delivery, Future Delivery
Review
GO FORWARD
Go forward (advance)
GUEST MBXES
GST
GST
Manage Guest Mailboxes
IMM ALL FAX
SNDN
Immediate Fax (all faxes in folder)
IMM THS FAX
SND1
Immediate Fax (current fax doc)
MARK PRIVAT
PRV
PRV
Set Private status (On/Off)
MARK
URGENT
URG
URG
Set Urgent status (On/Off)
Stratagy ES User Guide
01/03
87
Using Stratagy ES with a Strata CTX
Toshiba Proprietary Integration
Table 3
Soft Keys for CTX Digital Telephones (continued)
DKT 3014 SDL
MSG
FOLDERS
DKT 3010 SD
DKT 3020 SD
FLDR
DKT 2010 SD
DKT 2020 SD
FLDR
MSG NOTIFY
Manage Personal Folders
Change message Notification
MULTI ENTRY
MULTI
MULTI
Multiple Destinations
NAME
RECORD
NAME
NAME
Record your Name
NEXT
NEXT
NEXT
Play next message
Play next message (Future Delivery
Review)
NEXT MSG
NEXT NAME
NEXT
NEXT
PAUSE
PAUS
PAUS
PAUSE PLAY
Play next name
Pause recording
Pause playback
PER DST LST
LIST
LIST
Manage Personal Distribution Lists
PERSONAL
LIST
LIST
LIST
Personal distribution list (1~25)
PM?
PM
PREVIOUS
Play the Previous message
Return to previous menu
PREV MENU
PREV
REC
COMMENT
COMM
COMM
Record a list Comment
RECORD
REC
REC
Record
Re-enter automatic copy destination
REENTER
REENTER
NAM
REDO
REDO
Re-enter name or Exit
Replay current message
REPLAY
88
Voice Mail Functions
REPLY
RPLY
RPLY
Reply to the current message
RE RECORD
RREC
RREC
Re-record
Stratagy ES User Guide
01/03
Using Stratagy ES with a Strata CTX
Toshiba Proprietary Integration
Table 3
Soft Keys for CTX Digital Telephones (continued)
DKT 3014 SDL
DKT 3010 SD
DKT 3020 SD
DKT 2010 SD
DKT 2020 SD
Voice Mail Functions
RESET
PWORD
RSET
RSET
Reset Guest Password
RETRN RECPT
RTRC
RTRC
Set Return Receipt request (On/Off)
REVIEW
REVW
REVW
Review recording/guest mailboxes
REVIEW LIST
REVW
REVW
Review current list
REV OPTIONS
SAVE
Review Option Settings
SAVE
SAVE
SAVE MSG
Save the message/recording/changes
Save message (Future Delivery Review)
SECURITY
COD
CODE
CODE
Change Security Code
SELECT NAME
PICK
PICK
Select name
SEND MSG
SEND
SEND
Send and Return to Main menu
SET DAY
Set the Day (1~31)
SET HOUR
Set the Hour (1~12)
SET MINUTES
Set the Minutes (0~59)
SET MONTH
Set up Month (1~12)
SET YEAR
Set up Year (last two digits)
SPCL FUNCT
SPCL
Special Functions
SND ALL FAX
FAXN
Send All Fax (in folder to fax dev)
SND THS FAX
FAX1
Send Current Fax (to fax device)
SPCIAL SEND
SPCL
SPCL
START TIME
STOP
Set copy Start Time
STOP
STOP
URGENT
MSGS
USER OPTNS
Special Delivery Options
End recording
Copy Urgent Messages
OPTN
YES
Stratagy ES User Guide
OPTN
Change User Options
Resume playback
01/03
89
Using Stratagy ES with a Strata CTX
Toshiba Proprietary Integration
Call Record to Stratagy ES
While on an active call, a station user can record the conversation and store it in a
Stratagy ES voice mailbox. Recordings can also be paused or restarted. Depending
upon your System Administrator, you are given either a manual method of recording
that allows you to designate the mailbox where the recording will be sent or an auto
method that automatically sends the recording to a predefined mailbox that is assigned
to the phone you are using. This may be your personal mailbox.
Note Ask your System Administrator which method you need to use when recording
a call.
This feature requires the presence of a 5HFRUG and a 365(6 (Pause/Resume)
button on your telephone. Feature codes are not available.
Important!
Stratagy ES mailboxes have a definable limit on the length one message
can be. If you plan on doing lengthy recordings using this feature, see
your System Administrator so your message recording time can be
properly defined.
➤ To record a call
1. With a call in progress, press 5HFRUG.
If you are using the auto method, the Record LED flashes rapidly and there is
approximately a one second interval (in extreme busy conditions, up to five
seconds) before the recording starts and the Record LED changes to the in-use
interval flash rate. You are now recording. Continue to Step 3.
...or if you are using the manual method, the Record LED flashes green rapidly.
Continue to Step 2.
2. (Manual method only) If you want to record the call to the predefined mailbox
associated with the phone you are using, press . The Record LED flashes rapidly
and there is approximately a one second interval (in extreme busy conditions, up to
five seconds) before the recording starts and the Record LED changes to the in-use
interval flash rate. You are now recording.
...or if you want to record this call to another mailbox, enter the mailbox number
(usually the extension number). Finish by pressing .The Record LED flashes
rapidly and there is approximately a one second interval (in extreme busy
conditions, up to five seconds) before the recording starts and the Record LED
changes to the in-use interval flash rate. You are now recording.
90
Stratagy ES User Guide
01/03
Using Stratagy ES with a Strata CTX
Direct Transfer to Voice Mailbox
3. To stop recording, press 5HFRUG. The LED turns off and the recording stops. To
resume recording at this point, you need to begin a new recording, see Step 1 on
previous page.
Pause/Resume Recording
You can pause the recording while continuing the conversation by pressing 365(6.
The PS/RES LED flashes red. Your conversation is no longer being recorded.
To resume recording as part of the same message, press the 365(6 button again.
You can pause and resume indefinitely throughout the conversation. The only limit
may be a message length imposed by the voice mail system.
Direct Transfer to Voice Mailbox
An internal user on the Strata CTX can transfer a call directly to another person’s
voice mailbox without waiting for the call to forward from the called party’s
telephone. The voice mailbox does not even need to be associated with an active
telephone in the Strata CTX.
Direct Transfer to Voice Mail simplifies getting a call for a busy or absent employee to
his/her mailbox. It eliminates the need for the caller to enter the desired mailbox
number after being connected to the voice mail system.
➤ To transfer a call directly to Voice Mail (VM)
1. While on a call, press &QI7UQ. You hear feature dial tone.
2. Press 'LUHFW7UDQVIHUWR90 or enter . You hear entry tone.
3. Enter the VM mailbox number (usually the same as the extension number), then
press . The call transfers immediately and your extension becomes idle. The
transferred party hears the greeting associated with the specified mailbox and can
then leave a message.
Note See Strata CTX 3000/2000-series Telephone User Guide for information on
programming this feature on your phone.
Voice Mail Conference
Voice Mail ports may be included in conference calls. This enables all members of the
conference to listen to and play voice mail messages.
Stratagy ES User Guide
01/03
91
Using Stratagy ES with a Strata CTX
Voice Mail Conference
92
Stratagy ES User Guide
01/03
Fax Printer Driver
B
The Stratagy ES Fax Printer Driver enables you to select a document that you have
created on your computer and after converting it to a Tagged Image Format (TIFF),
gives you the option to store the file locally on your hard drive, send it to another
Stratagy ES user’s mailbox, or transmit it to a remote facsimile device using the fax
ports of the Stratagy ES.
Notes
• The ability of sending faxes through the Stratagy ES requires the server be updated
with the optional Fax Server Feature Group. Check with your System
Administrator to find out if your system is configured for the Fax Server Feature
Group.
• This printer driver can only be used on computers running Windows® 2000/ME/98
and Windows NT®.
Stratagy ES User Guide
01/03
93
Fax Printer Driver
Configure/Personalize Fax Printer Driver
Configure/Personalize Fax Printer Driver
Note To use this printer driver, you must first load the Stratagy ES Fax Printer Driver
on your computer. See your System Administrator for details.
1. From Windows, select
Start, Settings, then Control
Panel.
5621
2. From the Control Panel
screen, select SES
FaxClient.
5622
94
Stratagy ES User Guide
01/03
Fax Printer Driver
Configure/Personalize Fax Printer Driver
3. In the Host name: field on
the SES tab screen, type the
computer name or IP
address for the Stratagy ES.
Check with your System
Administrator for this
information.
4. Click on Login tab.
5623
5. Fill in the following fields
on the screen:
• Mailbox Id – Type your
mailbox number in the
Stratagy ES.
• SAC – Type your
mailbox’s security code.
• Verify SAC – For
verification, type your
mailbox’s security code
again.
Stratagy ES User Guide
01/03
95
Fax Printer Driver
Configure/Personalize Fax Printer Driver
• Never show the Login
dialog – Check/uncheck
whether or not you want
to type your mailbox
number and security
code each time you use
the Stratagy ES Fax
Printer Driver.
6. Click the Cover Page tab.
6590
7. Fill in the Name/Company/
Phone/Fax and E-mail
fields. This information
becomes the From: data on
the cover page each time
you send a fax using the
Stratagy ES Fax Printer
Driver.
8. For custom cover pages, the
Image field needs to define
the location of the template
file being used for the cover
page.
Note If a custom cover page is
desired, see your System
Administrator for details.
96
Stratagy ES User Guide
01/03
Fax Printer Driver
Use Fax Printer Driver
Use Fax Printer Driver
1. With the document
displayed on your PC’s
monitor, select the Print
option from the File menu.
2. From the Name field’s
drop-down menu, select
StratagyES Fax.
5625
3. Click OK.
5822
Note If you removed the check mark from the
Never show the Login dialog field (SES
Fax Client Setup screen) when you
configured the fax printer driver, this
screen does not display. See Step 5 on
page 95 for details.
Stratagy ES User Guide
01/03
97
Fax Printer Driver
SES Fax Client Screen
4. Type your mailbox number
and security code in the
fields provided.
Once authorization has been satisfied, the SES
Fax Client window displays (see “SES Fax
Client Screen” on page 98).
Note This is a security feature
to prevent unauthorized
use of Stratagy ES fax
features.
SES Fax Client Screen
The SES Fax Client screen (shown below) enables you to create and send a fax using
Stratagy ES. Using the fields on this screen, you can address the fax (destination, fax
number), add a cover page or a note to the fax, and enter destination information
(name/company/fax/phone/e-mail) that will appear on the top of the cover page.
6585
98
Stratagy ES User Guide
01/03
Fax Printer Driver
SES Fax Client Screen
Table 4
SES Fax Client Screen Fields
BUTTON
DESCRIPTION
Document Title
Defines the name of the document that you are attempting to fax.
Pages
Provides a page count of the fax document.
Destination Type
Enables you to select the type of destination for this fax. The three options
are Local file, Mailbox, or Phone number.
Phone/Mailbox List/
Path
Depending on which Destination Type was selected, this field defines the fax
number, mailbox number, or file name.
Browse
Enables you to browse for a path/directory where you can store the TIF file,
or to peruse the Stratagy ES user directory for a destination mailbox number.
Add
Adds the defined destination to the list for distribution.
Remove
Removes the highlighted destination from the list.
Add List
Enables you to select a previously created list to the distribution.
Save List
Saves the currently defined list entries as a distribution list.
Add Cover Page
Provides the bottom portion of the screen where destination information can
be defined.
Schedule
Enables you to schedule the fax for future delivery.
Send
Sends the fax to the defined destinations.
To (Name/Company/
Fax/Phone/Email)
Defines destination information (such as a recipients name, company, phone
number, etc.). This information appears on the cover page.
Add a Note
Provides a text box where comments can be written and added to the cover
page.
Stratagy ES User Guide
01/03
99
Fax Printer Driver
Schedule Fax for Future Delivery
Schedule Fax for Future Delivery
1. After filling out the SES Fax Client
screen, click Schedule. The Schedule
Fax screen displays (shown right).
2. Using the drop-down menu select the
date.
3. Using the scroll buttons, set the time of
day.
4. Click Send
6586
100
Stratagy ES User Guide
01/03
Automatic Speech Recognition
C
Note Automatic Speech Recognition (ASR) is an optional feature in the Stratagy ES.
Check with your System Administrator to find out if your system is configured
for this feature.
Stratagy ES’s ASR feature enables you to speak into the phone and accomplish the
following tasks:
• Reach a destination by saying the user’s name
• Log into your mailbox by saying a login command
• Send a message by saying “send message” or “quick message”
A typical company instructional greeting when you reach your company’s main phone
number would be, “Thank you for calling ABC Corporation. Please say the full name
of the person you wish to reach or enter the extension number. You can also say ‘send
message’ to send a message or ‘login’ to login to your mailbox.”
This appendix covers the general procedures for each of these tasks.
Stratagy ES User Guide
01/03
101
Automatic Speech Recognition
Reach Destination
Reach Destination
After listening to your company’s instructional greeting and saying the user’s name,
Stratagy ES follows this procedure:
• Stratagy ES identifies the name and transfers your call to the user’s mailbox.
• If Stratagy ES is not sure about the spoken name, it prompts you with the name
match it has made and requests that you confirm the choice by saying “yes” or
“no.” If you say “yes,” Stratagy ES transfers your call to the user’s mailbox.
...or if Stratagy ES cannot make a match for the spoken name (first or last name) or
you say “no” when prompted to confirm the spoken name, it prompts you to repeat
the name. If Stratagy ES recognizes the name when you repeat it, it transfers your
call to the user’s mailbox.
• If Stratagy ES still cannot identify the spoken name, it prompts you to spell the
first and last name. If Stratagy ES recognizes the name, it transfers your call to the
user’s mailbox.
...or if Stratagy ES cannot make a match, it transfers your call to the company
operator.
Note At any time during these steps, you can say “operator help” and reach the
company operator.
Access Your Mailbox
After listening to your company’s instructional greeting and speaking one of the login
commands (i.e., mailbox login, mailbox logon, user login, user logon, access mailbox,
log me in), Stratagy ES follows this procedure:
• Stratagy ES prompts you for your name. If Stratagy ES recognizes the name, it
then prompts you for your password.
...or if Stratagy ES does not recognize the name, it follows the same steps as in
“Reach Destination” procedure except it does not transfer you to an operator as a
final solution. Instead, Stratagy ES requests that you hang up and try again.
• You enter your password using the telephone dial pad. Stratagy ES gives you
access to your mailbox.
102
Stratagy ES User Guide
01/03
Automatic Speech Recognition
Send a Message
Send a Message
After listening to your company’s instructional greeting and saying either “send
message” or “quick message,” Stratagy ES follows this procedure:
• Stratagy ES prompts you to speak the name of the user for whom you want to leave
a message. Stratagy ES identifies the name and transfers your call to the user’s
mailbox where you can leave the message.
...or if Stratagy ES does not recognize the name, it follows the same steps as in the
“Reach Destination” procedure except it does not transfer you to an operator as a
final solution. Instead, Stratagy ES requests you hang up and try again.
Stratagy ES User Guide
01/03
103
Automatic Speech Recognition
Send a Message
104
Stratagy ES User Guide
01/03
Unified Messaging (UM)
with Outlook Integration
D
Unified Messaging (UM) lets you efficiently access e-mail, voice mail and fax
messages all within your e-mail inbox. You can also retrieve, save and forward all
these different types of messages as easily as you currently retrieve messages from
your telephone.
This appendix discusses how to play and send voice messages with Stratagy ES UM
using Outlook Integration. It also includes instructions on how to configure your
computer and Microsoft’s Outlook® to integrate with the Stratagy ES and how to set
up the different options for voice message playback and management.
Stratagy ES can integrate with Outlook e-mail client to provide innovative UM
functions. This integration enables you to play your voice messages over your
multimedia PC speakers or through your telephone.You can also view faxes on your
PC screen, no more going back and forth to the fax machine!
Note See the Stratagy Advisor CD-ROM for more UM information.
Stratagy ES User Guide
01/03
105
Unified Messaging (UM) with Outlook Integration
Stratagy ES Message Window
Stratagy ES Message Window
The Stratagy ES Message window (see Figure 2 below and Table 5 on page 107)
enables you to manage both your voice and fax messages from your PC.
The Message window displays when you select a message from the Microsoft
Outlook Inbox window. Using the toolbar, buttons and slides on the Message window,
you can perform all the necessary functions to play, send, forward or reply to a
message or view a fax.
Configure
Stratagy Voice
Mail Button
Standard
Outlook
Toolbar
Record Stratagy
Voice Message
Button
Telephone
Playback
Multimedia
Buttons
Voice Reply
Playback Slide
Voice Forward
Fax Viewer
5423
Volume Slide
Figure 2
106
Speed Slide
Stratagy ES Message Window
Stratagy ES User Guide
01/03
Unified Messaging (UM) with Outlook Integration
Stratagy ES Message Window
Table 5
Stratagy ES Message Box Buttons
BUTTON
DESCRIPTION
Multimedia
Enables you to play, rewind, fast forward, pause and stop message playback.
Playback Slide
Enables you to move to a specific part of the message by dragging this slide
button.
Volume Slide
You can adjust the volume of a message by moving the slider.
Speed Slide
If you are playing the message through your telephone, you can use this slide
bar to change the speed of the playback.
Voice Forward
Lets you easily forward a message to a co-worker.
Voice Reply
Displays only when you receive a message from a co-worker, enabling you to
reply to the sender.
Telephone Playback
Displays when you set up Outlook to play or record voice messages using
your telephone. Clicking on it, directs Stratagy ES to call your telephone to
start the play or record process.
Note
Fax Viewer
Displays when the message contains a fax. When you click on this button,
Outlook launches your computer’s designated application for viewing the
Tagged Image File Format (TIFF) files.
Note
Standard Outlook
Toolbar
While Stratagy ES is processing the call to your telephone, the icon
displays an off-hook receiver.
If your computer is not configured to view TIFF files, ask your
System Administrator for assistance.
You can also use this toolbar for sending voice replies and forwarding voice
messages to anyone that has e-mail.
Note
If you’re sending a voice message to someone who’s not on the
Stratagy ES system, you must also send the Stratagy ES audio
driver so the recipient can play the message on their computer. Your
System Administrator has details about this driver.
Configure Stratagy
Voice Mail
Using this button, you can select personal preferences, such as playing voice
messages through your PC speakers or telephone.
Record Stratagy
Voice Message
Using this button, you can easily record voice messages for co-workers or
any co-workers who use the Stratagy ES system.
Stratagy ES User Guide
01/03
107
Unified Messaging (UM) with Outlook Integration
Address Book Feature
Address Book Feature
➤ The Stratagy ES Address Book makes it easy to find and select addresses for user’s
mailboxes. The address book lists all voice mailbox addresses in the system.
The address book can be manually or automatically updated with the most current
mailbox list.
Update Stratagy ES Address Book Manually
➤ From the
Microsoft
Outlook Inbox
screen (shown at
right), select
Tools, then
Synchronize
Stratagy Address
Book. Stratagy ES
updates the
address book with
the most current
mailbox list.
5338
Update Stratagy ES Address Book Automatically
➤ The Stratagy ES Address book can be automatically updated with the Stratagy ES
at regular intervals (set number of days). See Step 9 on page 111 for instructions on
setting the feature.
108
Stratagy ES User Guide
01/03
Unified Messaging (UM) with Outlook Integration
Using UM Feature
Using UM Feature
Step 1: Configure Your Computer for UM
Note This step may have already been performed for you. Check with your System
Administrator.
Before using UM features, you’ll need to configure the Stratagy ES to coordinate and
synchronize information with your computer.
1. From the Standard Outlook toolbar,
click Configure Stratagy Voice Mail
(see Figure 2 on page 106). The
Stratagy ES Message Configuration
(Media Setting) screen displays
(shown right).
Note Using this screen, you can set up
your system to play voice
messages through speakers, and
determine how your Stratagy ES
messages are managed within
Outlook.
2. From the Media Setting tab screen,
select PC Speaker/Microphone or
Telephone handset as your choice for
playing and recording your messages.
• PC Speaker/Microphone – The
5421
messages play over your PC’s
speaker/microphone.
• Telephone handset – If you choose Telephone handset, you need to enter either
an extension number or direct dial number in the Telephone Number field. This
number is where you will receive your voice messages. A Telephone icon will
display on the Stratagy Message window indicating that you have chosen this
option.
3. In the next section of the screen, select the method you want Stratagy ES to use
when processing a message after you select it to play in Outlook.
Stratagy ES User Guide
01/03
109
Unified Messaging (UM) with Outlook Integration
Using UM Feature
• Save the message to my Stratagy personal folder – If you select this option, you
need to select one of your personal folders from the drop-down list where the
messages will be stored.
Important!
The default setting is folder “1” which is your saved message folder.
The Multiple Message Folder Feature must be enabled in order to use
folders 2~8. (See “Manage Personal Folders” on page 78.)
• Delete the message from Stratagy – Deletes the message automatically from
your Stratagy mailbox after it has been downloaded to Outlook.
Important!
If you choose to have messages deleted from the Stratagy ES mailbox,
the only copy of these messages that will be left will be on your computer.
4. Click OK and a dialog box informs
you that the changes will be applied
next time you open the message. Click
OK again, then User Information tab.
The User Information screen displays
(shown right).
5. In the Mailbox number field, type the
mailbox number of the user. Press
Enter.
6. In the Mailbox security code field,
type the security code for the
previously defined mailbox. Press
Enter.
7. The next two fields, Server name/IP
address and Domain name, should be
filled in by your System
Administrator.
8. In the Email password field, type your
e-mail password if you are going to use the e-mail Text-to-Speech (TTS) feature.
Press Enter.
53391
110
Stratagy ES User Guide
01/03
Unified Messaging (UM) with Outlook Integration
Using UM Feature
Notes
• The mailbox number, Server name/IP address and Domain name should have been
filled in during the installation of the Stratagy ES Outlook Integration software.
These fields are available if changes are required.
• Without this password, the TTS e-mail feature does not work.
• This password must match the one entered in the E-mail Server (e.g., Exchange)
account password for the TTS e-mail feature to function.
9. In the Synchronize StratagyES Address Book every ___ Days field, type the
interval (number of days) you wish to have Outlook synchronize with the
Stratagy ES for the latest directory updates. After the specified amount of days, an
automatic synchronization takes place.
To disable automatic synchronization, type zero for the number of days.
10. Click Apply.
Step 2: View Message Log
When you receive a
voice or fax message in
your Stratagy ES
mailbox, an e-mail
message is inserted into
your Outlook Inbox
(shown at right). The
Subject field tells you
what type of message
you received—voice,
fax or a voice and fax.
5422
Stratagy ES User Guide
01/03
111
Unified Messaging (UM) with Outlook Integration
Voice Mail Options
Step 3: Select Message
➤ Double-click on a message listed in the Microsoft Outlook Inbox. The Stratagy ES
Message window displays (see Figure 2 on page 106), enabling you to manage
both your voice and fax messages from your PC.
See “Voice Mail Options” on page 112 and “View Fax” on page 115 for
instructions on using your voice and fax mail.
Note When you listen to and delete a Stratagy ES message by telephone, the e-mail
listing is not deleted from the Outlook screen. If you click on the screen listing,
you are alerted that the message has already been deleted by telephone. You
must now delete it from the Outlook screen.
Voice Mail Options
UM voice mail option enables you to:
•
•
•
•
Play a voice message
Reply to a voice message
Forward a voice message
Send a voice message
Play Voice Message
➤ From the Stratagy Voice and Fax Message screen, click Play on the multimedia
e
us
5424
Pa
p
to
En
d
w
ar
Sk
i
Fo
r
p
Sk
i
y
Pl
a
St
op
ec
or
d
k
R
ac
B
p
Sk
i
Sk
i
p
to
St
ar
t
d
bar. The voice message plays. While the message is playing you can use the other
multimedia buttons to navigate through the message (see Figure 3).
Figure 3
112
Multimedia Bar (Buttons)
Stratagy ES User Guide
01/03
Unified Messaging (UM) with Outlook Integration
Voice Mail Options
1. From the Stratagy Voice and
Fax Message screen, click
Voice Reply. Another message
form displays with the To field
filled in with the address of the
original sender (shown right).
2. Click Record (see Figure 3) on
the multimedia bar.
3. Speak your message clearly
into the microphone.
4. Click Stop on the multimedia
bar.
5. Click Send on the toolbar. The
Reply Message window closes.
The Outlook Inbox remains on the screen.
6. (Optional) From the Outlook Inbox screen, type a brief note into the Comments
field about the voice message so you will not have to replay it to review the
contents.
Stratagy ES User Guide
01/03
5524
Reply to Voice Message
113
Unified Messaging (UM) with Outlook Integration
Voice Mail Options
Forward Voice Message
5425
1. From the Stratagy Message
window, click Voice Forward.
Another message form
displays (shown right).
5426
2. Click To field. The Select
Names screen displays (shown
right).
3. From the Show Names from
the field drop-down list, select
the Stratagy ES Address Book.
4. Select a name or names from
the address book. Click OK.
The screen in Step 1 above
displays with the To field filled
in with your destination(s).
5. (Optional) To record a
comment to go along with the
forwarded message, click
Record on the multimedia bar.
6. Speak your message clearly into the microphone. When finished, click End
Recording on the Standard Outlook Toolbar (see Figure 2 on page 106).
7. Click Send. The Reply Message window closes. The Outlook Inbox remains on the
screen.
114
Stratagy ES User Guide
01/03
Unified Messaging (UM) with Outlook Integration
View Fax
1. From the Stratagy Voice and
Fax Message screen, click
Record Stratagy Voice
Message in the Standard
Outlook toolbar.
2. Click To field. The Select
Names screen displays (shown
right).
3. From the Show Names from
the field drop-down list, select
Stratagy ES Address Book.
4. Select a name or names from
the address book. Click OK.
The screen in Step 1 above
displays with the To field filled in with your destination(s).
5. Click Record (see Figure 3) on the multimedia bar.
6. Speak your message clearly into the microphone.
7. Click Stop.
8. Click Send. The Message window closes. The Outlook Inbox is still displayed.
5426
Send Voice Message
View Fax
UM enables you to view a fax message.
➤ From the Stratagy Voice and Fax Message screen, click Fax Viewer (see Figure 2
on page 106). The Stratagy ES Message window launches your computer’s
designated application for displaying TIFF files.
Note Most imaging software lets you edit the fax, zoom in and out, rotate its view.
You need to check with your System Administrator on your software’s features.
Stratagy ES User Guide
01/03
115
Unified Messaging (UM) with Outlook Integration
View Fax
116
Stratagy ES User Guide
01/03
Unified Messaging with
IP Integration
E
This appendix provides instructions on how to configure your computer to properly
record .wav files in the correct format to send into Stratagy ES as voice messages.
Note This process is only necessary if your computer is configured to use Unified
Messaging with Internet Protocol (IP) Standard Integration.
Stratagy ES User Guide
01/03
117
Unified Messaging with IP Integration
Configure Windows for Stratagy ES Codec
Configure Windows for Stratagy ES Codec
Note Before beginning the setup procedure, the TAIS Audio Codec must be installed
on your PC.
Check Codec is Installed on
PC
5950
1. Click Start >Settings > Control Panel >
Sounds and Multimedia > Hardware tab
(shown right).
2. Confirm if the Stratagy ES Audio Codec
is present. If it is present, continue with
this setup. If it is not, contact your
System Administrator to have the Codec
installed on your PC.
118
Stratagy ES User Guide
01/03
Unified Messaging with IP Integration
Configure Windows for Stratagy ES Codec
Configure Windows
5558
1. Click Start > Settings > Control Panel >
Multimedia (shown right).
2. In the Recording section of the
Multimedia Properties window, click
Customize. The Sound Selection screen
displays (shown right).
Sound Selection screen directly by
selecting Start > Programs >
Accessories > Entertainment >
Sound Recorder > File > Properties > Convert Now.
5559
Note In Windows 2000 you can access the
3. From the Sound Selection screen, select Toshiba ADPCM from the Format field’s
drop-down menu (this value is only present if the TAIS Audio Codec has been
properly installed).
4. From the Attributes field, select 8,000 KHz, 4 Bit, Mono from the drop-down
menu.
Stratagy ES User Guide
01/03
119
Unified Messaging with IP Integration
Record Stratagy ES Voice Messages (using Windows Sound Recorder)
5561
5. Click Save As and the Save As dialog
box displays. Type Stratagy ES Format
in the available field.
5560
6. Click OK. The Sound Selection screen
displays (shown right).
7. From the Sound Selection screen, click
OK.
8. From the Multimedia Properties screen,
click OK to quit Multimedia Properties.
This completes the setup.
Record Stratagy ES Voice Messages (using
Windows Sound Recorder)
This procedure explains one way in which to record a .wav file that can be sent into
the Stratagy ES as a voice message. Other multimedia software can be used to perform
this function provided that the software provides a way to set the recording
compression rate. To use Microsoft Sound Recorder, perform the following:
1. From the Start Menu, select Programs > Accessories > either Multimedia
(Windows NT®) or Entertainment (Windows 98 & Windows 2000) > Sound
Recorder.
2. Click Record (red button) and record your message through the multimedia
microphone connected to your PC.
3. When finished recording, click on File > Save As.
4. Select a folder in which to save the .wav file.
5. Enter a File name for the .wav file.
6. Click Change. The Sound Selection window displays.
7. From the Name field’s drop-down menu, select Stratagy ES Format. The attributes
should change to reflect the proper compression of 8,000 KHz, 4 Bit, Mono.
8. Click OK to close the Sound Selection window. The Save As window displays.
9. If the target folder information is correct, click Save.
120
Stratagy ES User Guide
01/03
Unified Messaging with IP Integration
Send .WAV File as Voice Message
1. To send the .wav file
into Stratagy ES as
either a new, reply, or
forwarded voice
message to a mailbox,
attach the .wav file to an
e-mail message (shown
right).
2. Make sure that the
address for the message
is correct. The
addressing convention
for sending voice
messages into a Stratagy
ES is defined as <target
mailbox
number>@<system
computer name.domain>.
5562
Send .WAV File as Voice Message
Note As a quick tip, every time you get a Stratagy ES voice message from a
Stratagy ES voice mail user, add that address to your personal address book.
If other Stratagy ES mailbox addresses are entered in either the To:, cc:, or bcc:
fields, those mailboxes also receive your message.
Stratagy ES User Guide
01/03
121
Unified Messaging with IP Integration
Send .WAV File as Voice Message
122
Stratagy ES User Guide
01/03
Remote User Password
Administration for TTS
F
This appendix provides instructions on how to update the Stratagy ES software with
your e-mail log on password so that the system can retrieve e-mail messages and read
them via Text-to-Speech (TTS).
Note This procedure is only required if you have TTS Privileges and you use Unified
Messaging with the Internet Protocol (IP) Standard Integration.
Please contact your System Administrator to confirm your mailbox privileges.
To update the Stratagy ES with your e-mail password, the Stratagy ES Remote User
Password Administration applet must be installed on the your computer.
• Without the password, the TTS e-mail feature does not work.
• This password must match the E-mail Server (e.g., Exchange) account password for
the TTS feature to work.
Stratagy ES User Guide
01/03
123
Remote User Password Administration for TTS
Set Remote User Password
Set Remote User Password
➤ To install Stratagy ES Remote User Password Administration applet
1. Insert the Stratagy ES Software CD-ROM into your computer.
2. From the Main
Menu, select
Remote User
Password
Administration.
The Stratagy ES
Remote User
Password
Administration
screen displays
(shown right).
6588
3. Enter the Stratagy
ES mailbox number
for the user.
4. Enter that mailbox’s security code.
5. Enter the password that you enter to log into your e-mail service.
6. Enter the computer name or IP address of the host Stratagy ES system on the local
network. Your System Administrator should have this information.
7. Enter the computer name or IP address of the host SMTP server on the local
network.
8. Click Send Update. The applet will securely send your e-mail password directly
into the Stratagy ES system. Your System Administrator should have this
information.
124
Stratagy ES User Guide
01/03
Using Stratagy ES with a
Strata Legacy System
G
Notes
• Toshiba Legacy systems are Strata DK8/16, DK14, DK40i, DK424i, DK24/56/96.
For information on Strata CTX systems, see Appendix A – Using Stratagy ES with
a Strata CTX.
• The naming convention for DKT assignments within Toshiba is Directory
Numbers. For clarity and ease of understanding, the terms Extension Number and
Phantom Extension Number will be used in this document in lieu of PDN and
PhDN.
This appendix explains the procedures for programming Toshiba Legacy proprietary
telephones for Call Forward and Message Retrieval when using a Stratagy ES Voice
Processing System with one of the following Toshiba telephone systems:
• Strata DK14, DK40i, DK424i
Note Any reference to Strata DK 424i in this appendix, should be read to include
DK424 and DK280. Any reference to DK40i should be read to include DK40
and DK16e.
• Strata DK8/16, DK24/56/96
Once programmed, your Stratagy ES voice processing system can answer calls when
you are busy or not available. It can give callers choices when you do not answer, such
as: recording a message, dialing another extension, or dialing 0 for assistance.
Note This appendix does not include the procedures for Call Forward and Message
Retrieval with a standard telephone. Consult the appropriate Toshiba Standard
Telephone User Guide for these instructions.
Stratagy ES User Guide
01/03
125
Using Stratagy ES with a Strata Legacy System
Call Forward
If you have a Strata telephone system, you need to program your telephone only once
for the Call Forward and Message Retrieval functions. Then you can follow the
appropriate steps for using Call Forward and Message Retrieval.
Notes
• If you do not have Call Forward keys, you can use access codes instead. Refer to
the appropriate User Guide for the Call Forward access/cancellation codes or
check with your System Administrator.
• If the Stratagy ES is fully integrated with your telephone system, you may not need
to enter a Voice Mail ID code for Call Forwarding or Message Retrieval. Please
consult your System Administrator if Voice Mail ID codes are required.
• With most Toshiba proprietary telephones, you can store the sequence of steps on a
Speed Dial button for quick access. Refer to the appropriate Quick Reference or
User Guide for your telephone for information and instructions on using Speed
Dial buttons.
Call Forward
To direct forwarded calls to your mailbox and to ensure that callers receive your
personal greeting, additional internal access digits must be programmed initially from
your telephone for your extension number and for each phantom extension number by
your telephone. These digits are called voice mail ID codes.
Note Your telephone must be the owner of the phantom extension number to store a
voice mail ID code for the phantom extension number.
Set Call Forward to Stratagy ES
Skip to “To forward calls to Stratagy ES” on page 128 if you have already performed
this function. Once programmed, this code is automatically sent to the Stratagy ES
system whenever calls are forwarded to the Stratagy ES system from your telephone,
enabling callers direct access into your mailbox.
126
Stratagy ES User Guide
01/03
Using Stratagy ES with a Strata Legacy System
Call Forward
➤ To program the Stratagy ES Voice Mail Code from a Strata DK telephone
1. Press the extension number
or phantom extension
number.
2. For Strata DK14, DK40i,
and DK424, press ...or for Strata DK8/16 and
DK24/56/96, press .
3. Press .
4. Enter your Stratagy ES
mailbox number.
5. Press 5HGLDO.
6. Press 6SNU.
You hear a dial tone.
You hear a confirmation tone. Display
telephones show “#656 I.D. CODE SET.”
You have completed programming and hear a
confirmation tone. Display telephones show
“656 I.D. CODE SET.”
You hear a confirmation tone. Display
telephones show “DATA PROGRAMED.”
Resets your telephone to the idle condition.
Notes
• To change the voice mail code, repeat steps.
• In order for the button to function properly
while using the Stratagy ES system with a
Toshiba Strata system, the 6SHHG'LDO
(5(36'6) button and the 5HGLDO (5'/)
button must be provided on your Toshiba
proprietary telephone.
Stratagy ES User Guide
01/03
127
Using Stratagy ES with a Strata Legacy System
Call Forward
➤ To forward calls to Stratagy ES
1. Press the appropriate &DOO
)RUZDUG button
...or press the extension
number or phantom
extension number, then
enter the appropriate Call
Forward access code.
2. Dial the Stratagy ES system
number _____________.
128
The Call Forward LED flashes, or you hear a
confirmation tone.
You hear a confirmation tone if an access code
is dialed. Display telephones show “CALL
FORWARD TO.”
Call Forward Access Codes
Strata
DK8/16 and
DK24/54/96
Strata
DK14,
DK40i, and
DK424i
Call Forward All Calls
Call Forward Busy
Call Forward No Answer
Call Forward Busy No
Answer
You hear a confirmation tone.
Stratagy ES User Guide
01/03
Using Stratagy ES with a Strata Legacy System
Call Forward
3. (Optional) For Call
Forward-No Answer and
Call Forward- Busy/No
Answer, you can set the
number of seconds that
your telephone rings before
forwarding.
If you pressed a Call
Forward button in Step 1,
enter the numberof seconds
(a)
...or if you pressed a
extension number or
phantom extension number
in Step 1, press 6SHHG
'LDO and enter the number
of seconds (a).
4. Press the same Call
Forward button used in
Step 1
...or if you used an access
code sequence, press
5HGLDO, then 6SNU.
Stratagy ES User Guide
01/03
Note Some older telephones do not have
6SHHG'LDO and 5HGLDO buttons. You
may need to press 6'6 (or 5(3) + the
number of seconds (08~60) + 5'/ or + the number of seconds (08~60) + .
The Call Forward LED lights steady.
129
Using Stratagy ES with a Strata Legacy System
Call Forward
Cancel Call Forward
1. Press the appropriate &DOO
)RUZDUG button, then
6SNU
...or press the extension
number or phantom
extension number, then
enter the appropriate Call
Forward access code.
The Call Forward LED turns OFF, or you hear a
confirmation tone. Call Forward registration is
canceled.
You hear a confirmation dial tone. Display
telephones show “CALL FORWARD TO.”
Dialing the access code (e.g., ) and no
station number cancels any Call Forward type.
See “To forward calls to Stratagy ES” on page
128 for access codes.
2. Press 6SNU (63($.(5).
Cancel the Programmed Call Forward Voice Mail Code
1. Press the extension number
or phantom extension
number.
2. For Strata DK14, DK40i,
and DK424i, press .
...or for Strata DK8/16 and
DK24/56/96, press .
3. Press 5HGLDO.
You hear a dial tone.
You hear a confirmation tone. Display
telephones show “#656 (or 656) ID CODE
SET.”
You will hear a confirmation tone. Display
telephones show “DATA PROGRAMED.” The
voice mail code is canceled.
4. Press 6SNU (63($.(5).
130
Stratagy ES User Guide
01/03
Using Stratagy ES with a Strata Legacy System
Message Retrieval
Message Retrieval
You can program your 0VJ or phantom extension number/message waiting buttons to
automatically retrieve your voice mail messages when you press it.
Skip to “To retrieve messages with Msg or Phantom Extension Number/Message
Waiting button” on page 132 if you have already performed this function. Once
programmed, this key does not need to be programmed again.
➤ To program your 0VJ button to retrieve messages
1. Press the extension number
or phantom extension
number.
2. For Strata DK8/16 and
DK24/56/96, press .
For Strata DK14, DK40i,
and DK424i, press .
3. Press (the Voice Mail
ID code for Message
Retrieval).
4. Enter your Stratagy ES
mailbox number + .
5. Enter your security
code + .
6. Press 5HGLDO.
You hear a dial or confirmation tone after you
press the button.
You hear a confirmation tone. “657” or “#657”
is the Stratagy ES System Identification code
for message retrieval from voice mail.
Your telephone must have the 6SHHG'LDO
(5(3, 6'6) button and the 5HGLDO (5'/)
button for the button to function properly
while using the Stratagy ES system.
By storing your security code, you avoid having
to enter your code every time you access your
mailbox.
Important! Including your security code in
this programming will enable
anyone to retrieve your messages
from your phone. If a security code
is not desired, do not include it.
You hear a confirmation tone. Display
telephones show, “DATA PROGRAMED.”
7. Press 6SNU.
Stratagy ES User Guide
01/03
131
Using Stratagy ES with a Strata Legacy System
Message Retrieval
➤ To retrieve messages with Msg or Phantom Extension Number/Message Waiting
button
➤ When the Message LED
flashes…
For Strata DK14, DK40i,
and DK424i, press 0VJ or
[Phantom Extension
Number/MW]
...or for the Strata DK8/16
and DK24/56/96, press the
extension number + 0VJ.
Stratagy ES is called and you are automatically
connected to your mailbox.
The system automatically calls Stratagy ES.
Note Pressing 0VJ before the extension
number cancels the message waiting
notification (e.g., the message light goes
Off even though the registered messages
may not have been retrieved).
➤ To cancel automatic retrieval
➤ For Strata DK14, DK40i, and DK424i, press the extension number or phantom
extension number + + 5HGLDO
...or for the Strata DK8/16 and DK24/56/96, press the extension number or
phantom extension number + + 5HGLDO.
Note If you have a Toshiba telephone system, see Chapter 5 – Manage Mailbox for
further instructions on using the Call Forward and Message Retrieval features.
If you have one of the telephones listed in that chapter, you may need to
program your telephone (once) so that the message waiting key works properly.
Depending upon your telephone system and telephone, a message waiting light
is lit on your telephone when a voice message has been left for you on the
Stratagy ES system.
If configured, Stratagy ES automatically turns off your message waiting light
on your telephone when your new message queue is empty or only partially
heard messages remain. All unheard messages must be accessed and partially
heard, deleted or saved for Stratagy ES to turn off the message waiting light on
your telephone.
132
Stratagy ES User Guide
01/03
Glossary
This glossary defines frequently-used Stratagy ES voice processing system features and
functions.
Term
Definition
Busy Greeting
You can select your custom busy or the system busy greeting for
callers to hear when your telephone is busy. If you do not record
your custom busy greeting, the system busy greeting
automatically plays.
Call Screening
Call Screening operates in On/Off mode. When On, Stratagy ES
asks callers for their name and company. Without the caller’s
knowledge, the system relays that information to you. You can
decide to receive the call, let the call forward to your mailbox, or
transfer the call to another extension with or without
announcement.
Caller
Someone who calls into the Stratagy ES system. A caller can
obtain information, leave a message for someone, and/or
provide information.
Called Party
The telephone user the caller reached. See “User.”
Directory
A caller enters digits corresponding to the first few letters of a
user’s name and Stratagy ES plays the recorded name (and
optionally extension) that matches the entered digits. Stratagy
ES offers the caller the option of selecting the name and being
transferred or hearing the next name.
Stratagy ES User Guide
01/03
133
Glossary
Do Not Disturb ~ Name Recording
Term
134
Definition
Do Not Disturb
Do Not Disturb operates in On/Off mode. When On, Stratagy ES
automatically sends calls to your mailbox without ringing your
telephone first.
Fax Messages
Fax messages sent to your mailbox. With the optional fax mail
feature, your mailbox can receive, store, and forward fax
messages along with voice messages. When you access your
mailbox, Stratagy ES tells you the number of fax messages in
your mailbox; and when you play the message, states the
number of pages received. You cannot listen to the actual fax
information. If you are calling from a fax machine, the fax can be
transmitted on the same telephone connection; otherwise, you
can direct the fax to a fax machine’s number. The system redials
the designated fax number and transmits the document.
FIFO (First In, First Out)
Messages play in either FIFO or LIFO order. FIFO plays
messages from oldest to newest.
Future Delivery
With future delivery, you can arrange for your message to be
delivered at a specific time and date in the future. Once you
send the message, you can use the Play Messages—Future
Delivery Review option to review, continue to send, or delete the
message.
Guest Mailbox
Guest mailboxes provide limited access to the Stratagy ES
system for temporary and project-oriented employees, such as
consultants and contractors. Guest users can only send and
receive messages to their Host mailbox and other guests of the
Host mailbox.
LIFO (Last In, First Out)
Messages play in either LIFO or FIFO order. LIFO plays
messages from newest to oldest.
Mailbox
A user mailbox records messages from callers. A user
periodically checks the mailbox for messages, etc., or a variety
of automatic notification methods can be employed. There is
generally one mailbox for each extension, although several
mailboxes can share a single extension when multiple users
share the same telephone line.
Name Recording
Your name (and optionally, extension) recording is used for the
directory, system greeting, and mailbox.
Stratagy ES User Guide
01/03
Glossary
New Message Folder ~ Saved Message Folder
Term
Definition
New Message Folder
The new message folder contains unheard and partially heard
messages. When playing new messages, urgent messages
always play first.
Personal Folders
Mailboxes configured for multiple folders can create up to seven
personal folders for saving messages. The folders can only be
accessed by the mailbox user that created them.
Personal Greetings
You may record up to seven personal greetings which are
played for callers when you are unavailable. Although only one
greeting can be in effect at any one time, you can switch
between the greetings by entering the greeting number, or preschedule different greetings to play at a certain time and/or day.
Greetings can be reviewed or re-recorded. You can also select
the default system greeting.
Personal Distribution List
A mailbox user can create/modify up to seven personal
destination (distribution) lists and list comments for identification.
When sending messages, you can select a mailbox number,
personal distribution list, system distribution list, and/or the
directory as the destination.
Private Messages
You can mark a message “private,” meaning the message
cannot be forwarded by the recipient to another user. The
recipient is told the message has the Private attribute set when
listening to his/her messages.
Return Receipt
When sending, forwarding, or replying to a message, you can
request a return receipt. Stratagy ES notifies you when and by
whom the message was received. The recipient is not notified
that receipt verification was requested and cannot circumvent
the procedure.
Saved Message Folder
The saved message folder contains messages that you saved or
that were automatically saved by the system. Messages flagged
to be saved can be stored in the saved message folder.
Mailboxes configured for Personal folders have the option of
saving messages in a personal folder created by the mailbox
user.
Stratagy ES User Guide
01/03
135
Glossary
Security Code ~ User Notification
Term
136
Definition
Security Code
Each mailbox in the system has a security code. You must enter
your security code to access your mailbox. The security code
ensures the privacy of your messages, personal greetings, etc.
System Administrator
The representative in your company responsible for configuring
the Stratagy ES system and your mailbox to suit you and your
companies needs.
System Greeting
Pre-recorded greeting that adds your recorded name: “Please
leave a message for (name).” Can be used by any user on the
Stratagy ES system. Based on your selection, callers hear the
system greeting or a personal greeting.
System Distribution List
System-wide destination (distribution) list the System
Administrator creates for Stratagy ES system users. When
sending messages, you can choose a mailbox number, personal
distribution list, system distribution list, and/or the directory as
the destination.
Toshiba Proprietary
Integration
Proprietary integration between Strata CTX phone system and
Stratagy ES voice mail. Provides a Soft Key Control of Voice
Mail feature that enables the user to perform many of the
standard functions using soft keys on the Strata 3000/2000series digital telephones.
Urgent Messages
Messages are stamped Urgent by the sender and by default, are
played first, followed by all other messages. The System
Administrator can set a notification record to use pager
notification exclusively whenever Urgent messages are
received.
User
Subscriber of the mailbox, also known as a mailbox user. A user
has access to one or more mailboxes in the system by knowing
the security codes. Once a user accesses his/her mailbox, he/
she can play back messages, delete those messages, send
them to other mailboxes, etc.
User Notification
Each mailbox can have notification records set by the System
Administrator to automatically call and notify you of your
messages. You can enable/disable the notify method for each of
these records or change the notification telephone number.
Stratagy ES User Guide
01/03
Index
A
C
about this guide
conventions, viii
organization, vii
related documents/media, x
access your mailbox, 18
ASR, 101
automatic message copy, 70
Automatic Speech Recognition, 101
call forward
system, 81
call record, 90
call screening, 61
change
greeting, 54
security code, 22, 62
user options, 59
continuous
delete, 30
play, 32
copy
automatic message, 70
B
basic functions
delete, 28, 34
forward, 28
play, 27, 34
replay current message, 28, 35
reply, 28
save, 27, 34
busy greeting, 10
record, 64
select, 63
buttons
extension, viii
Stratagy ES User Guide 01/03
D
date/time of message, 30
delete messages, 28, 34
destination
additional users, 42, 45, 47
directory, 13, 40, 43
mailbox number, 40, 43
multiple destinations, 41, 44
personal list, 12, 41, 44
system list, 13
137
Index
E~M
direct transfer to voice mailbox, 91
directory, 40, 43
distribution lists, 12, 13
E
e-mail messages, 9, 33
exit mailbox, 22
extension number, viii
sample, 21, 55
system, 10
guest mailboxes
manage, 76
use, 77
L
lists
personal distribution, 41, 44
F
fax messages, 9, 29
schedule for future delivery, 100
fax printer driver, 93
folders, 31
dual message, 5
new, 5
multiple message, 6
personal, 78
single message, 5
forward message, 8, 28, 43
future delivery, 11
faxes, 100
review, 30
setting, 42, 47, 49
G
getting started, 17
greeting
busy, 10, 64
change, 54
personal, 10
change your selection, 57
create, 55
record over, 55
review greeting, 58
138
M
mailbox, 19, 40, 43
access, 18
exit, 22
manage options, 53
personalize, 4
security code, 22
manage
guest mailboxes, 76
mailbox, 53
personal folders, 78
menu
main, 3
message waiting, 83
message waiting light
on [PhDN/MW], 84
on another telephone, 84
messages
access, 24
additional destinations, 42, 45, 47
append, 42, 47
automatic copy, 70
continuous delete, 30
continuous play, 32
control
Stratagy ES User Guide 01/03
Index
N~P
back up (rewind), 25
change speed, 25
go forward (advance), 25
pause/resume, 25, 44, 46
play next, 25
play previous, 25
replay current, 25
volume, 25
date and time, 30
delete, 28, 34
destination, 12
e-mail, 9, 33
fax, 9, 29
folders, 4
dual message, 5
saved, 6, 7
multiple message, 6
personal, 78
single message, 5
forward, 8, 28, 43
future delivery, 11, 30, 49
new message folder, 5, 31
notification, 68
play, 23
private, 11, 48
reply, 8, 28, 46
re-record, 41, 47
return receipt request, 11, 48
review recording, 41, 47
save, 27, 34
saved message folder, 6, 7, 31
send, 37
special delivery options, 11
types, 8
urgent, 11, 48
Stratagy ES User Guide 01/03
Msg button/LED, 83
multiple destinations, 41, 44
N
name
recording, 20, 66
new/saved messages, 5, 31
notification, 68
P
pause/resume playback, 25, 27, 44, 46
pause/resume recording, 38, 41
personal
distribution list, 41, 44
folders, 78
greeting, 10
change your selection, 57
create, 55
record over, 55
review, 58
sample, 55
play messages, 23
special functions, 29
playback
back up (rewind), 25
change speed, 25
continuous delete, 30
continuous play, 32
go forward (advance), 25
next message, 25, 27, 34
pause/resume, 25, 27, 44, 46
previous message, 25, 28
replay, 28, 35
replay current message, 25
volume, 25
private messages, 11, 48
139
Index
R~U
R
record
busy greeting, 64
messages
append
comment, 45
recording, 42, 47
re-record
comment, 45
message, 41, 47
review
comment, 45
recording, 41, 47
name, 20, 66
pause/resume, 38, 41
personal greeting, 21
record to voice mail, 90
reply message, 8, 28, 46
set future delivery, 49
special functions, 48
return receipt request, 11, 48
S
save messages
personal folders, 27
security code, 17
change, 22, 62
send messages, 37
soft keys, 84
special delivery options
private, 48
return receipt request, 48
urgent, 48
special functions, 29, 48
continuous delete, 30
140
continuous play, 32
date/time, 30
future delivery review, 30
immediate print all faxes, 29
immediate print current fax, 29
new/saved folder, 31
send fax, 29
Strata 3000/2000 digital phones, 84
Strata CTX, 84
Strata DK24/56/96, 8/16 and 280 telephones
call forward, 126
message retrieval, 131
system
greeting, 10
T
text-to-speech, 33
Toshiba Proprietary Integration, 84, 136
Toshiba telephone systems, 132
tutorial, 17
Stratagy ES Advisor, x
U
unified messaging, 105
address book feature, 108
configuration, 109
forward voice message, 114
message received, 111
play voice message, 112
reply to voice message, 113
select message, 112
send voice message, 115
update address book automatically, 108
update address book manually, 108
view fax, 115
Stratagy ES User Guide 01/03
Index
V~V
voice mail options, 112
unified messaging (IP integration), 117
configure windows for Stratagy ES
Codec, 118
record .wav file, 120
send .wav file, 121
urgent messages, 11, 48
user options
automatic message copy, 70
busy greeting, 14, 64
call screening, 14, 61
change, 59
do not disturb, 14, 60
message notification selection, 14, 68
security code, 62
user prompts, 15
user tutorial, 17
V
voice mail conference, 91
volume control, 25, 27
Stratagy ES User Guide 01/03
141
Index
V~V
142
Stratagy ES User Guide 01/03

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project