Toshiba ME00070B Remote Starter User Manual
CONTENTS 10.3 CONTENTS Quick Start AC53b Utilisation Codes ....................................... 32 2 1. Caution Statements 1.1 Cautions and warnings ............................................ 3 2. General Description 2.1 2.2 Feature list .............................................................. 4 Part Number format ................................................ 4 3. Specifications 3.1 3.2 3.3 3.4 3.5 Current ratings ........................................................ Dimensions & weights ............................................. Semiconductor fuses .............................................. Power terminations ................................................. General technical data ............................................ 5 7 7 8 8 4. Installation 4.1 4.2 4.3 4.4 General layout diagrams ......................................... 9 Power termination configuration .............................. 9 Mounting instructions .............................................. 9 Ventilation ............................................................. 10 5. Power Circuits 5.1 5.2 5.3 5.4 5.5 5.6 5.7 Overview .............................................................. 3 Wire connection ................................................. 3 Wire connection (Bypass operation) ................... 6 Wire connection ................................................. 6 Wire connection (Bypass operation) ................... Power factor correction ......................................... Line contactors ..................................................... 11 11 11 11 11 11 12 6. Control Circuits 6.1 6.2 6.3 6.4 Electrical Schematic .............................................. Control Supply ...................................................... Control Wiring ....................................................... RS485 Serial Communication ............................... 13 13 13 14 7. Programming & Operation 7.1 7.2 7.3 7.4 Programming Procedure ....................................... Function List ......................................................... Function Descriptions ........................................... Operation .............................................................. 17 18 18 24 8. Application Examples 8.1 8.2 8.3 8.4 Installation With Line Contactor ............................. Installation With Bypass Contactor ........................ Soft Braking .......................................................... Two Speed Motor ................................................. 26 26 27 28 9. Trouble Shooting 9.1 9.2 9.3 9.4 Trip Codes ............................................................ Trip Log ................................................................ General Faults ...................................................... Tests and Measurements ...................................... 29 30 30 31 10. Appendix 10.1 10.2 Typical Start Current Requirements ...................... 32 AC53a Utilisation Codes ....................................... 32 TMS7 SERIES ME00070B 1 QUICK START QUICK START 4. Use the <UP> and/or <DOWN> keys adjust the FLC setting to match the FLC of the connected motor. For simple applications TMS7 soft starters can be installed using the three simple steps outlined below. For applications with advanced control, protection or interface requirements a comprehensive review of this Users Manual is recommended. 5. Press the <STORE> key to store the new FLC setting. 6. Exit the programming mode by simultaneously pressing then releasing the <FUNCTION> and <STORE> keys. 1. Installation & Connection WARNING - ELECTRICAL SHOCK HAZARD The TMS7 contains dangerous voltages when connected to line voltage. Only a competent electrician should carry out the electrical installation. Improper installation of the motor or the TMS7 may cause equipment failure, serious injury or death. Follow this manual and National Electrical Codes (NEC ®) and local safety codes. 1. Ensure the correct TMS7 model has been selected for the connected motor and application type. 2. Mount the TMS7 making sure to allow adequate clearance top and bottom for the free circulation of air through the starter. (Refer to section 4.3 Mounting Instructions for further detail.) 3. Connect the supply cables to starter input terminals L1, L2 & L3. 3. Operation 4. Connect the motor cables to starter output terminals T1, T2 & T3. The TMS7 is now ready to control the motor. Motor operation can be controlled using the <START> and <STOP> keys on the TMS7 local control panel. Two other commonly used functions that may be useful for basic installations are Function 2. Current Limit and Function 5. Stop Ramp Time. These functions can be adjusted in the same manner as described above. (For a more detailed description of the programming procedure refer to section 7.1 Programming Procedure.) 5. Connect a control supply to starter input terminals A1 & A2 or A2 & A3. (Refer to section 6.2 Control Supply for further detail). (OP TIONAL) F1 L1 T1 L1B L2 3 PHASE SUPPLY T2 L3 T3 L3B C45 models 460V C24 model s +10 -15 400V +10 -15 230V OR 575V M L2B A1 +10 -15 A2 +10 -15 A3 OR E Legend F1 Semiconductor Fuses 2. Programming Basic application requires only that the TMS7 be programmed with the connected motor's nameplate full load current (FLC). To program the TMS7 with the motor's FLC do the following: 1. Put the TMS7 into program mode by simultaneously pressing then releasing the <FUNCTION> and <STORE> keys. 2. Select Function 1. Motor Full Load Current by holding down the <FUNCTION> key and then press the <UP> key until the display shows "1". 3. Release the <FUNCTION> key to display the currently stored value of Function 1. Motor Full Load Current. 2 ME00070B TMS7 SERIES CAUTION STATEMENTS Caution Statements WARNING - ELECTRICAL SHOCK HAZARD CAUTION This symbol is used throughout this manual to draw attention to topics of special importance to the installation and operation of the TMS7 soft starter. The TMS7 contains dangerous voltages when connected to line voltage. Only a competent electrician should carry out the electrical installation. Improper installation of the motor or the TMS7 may cause equipment failure, serious injury or death. Follow this manual and National Electrical Codes (NEC®) and local safety codes. GROUNDING AND BRANCH CIRCUIT PROTECTION CAUTION It is the responsibility of the user or person installing the TMS7 to provide proper grounding and branch circuit protection according to the National Electric Code (NEC ®) and local codes. It is the installers responsibility to adhere to all instructions in this manual, to follow good electrical practice and to seek advice before operating this equipment in a manner other than as detailed in this manual. • Ensure that the TMS7 is completely isolated from the power supply before attempting any work on the unit. • Do not apply voltage to the control input terminals. These are active 12/24VDC inputs and must be controlled with potential free circuits. • Ensure contacts/switches operating the control inputs are suitable for low voltage, low current switching ie, gold flash or similar. • Ensure cables to the control inputs are segregated from AC power and control wiring. • Entry of metal swarf into the cabinet can cause equipment failure. • Do not connect Power Factor Correction capacitors to the output of the TMS7. If static power factor correction is employed, it must be connected to the supply side of the TMS7. • Before installing the TMS7 without a line contactor ensure such connection meets local regulations and by -laws. • If installing the TMS7 within a non-ventilated enclosure a bypass contactor must be utilised to prevent excessive heat build-up. • If installing a by-pass contactor ensure phase connections are correctly made ie L1B-T1, L2B-T2, L3B-T3 • Removing control voltage resets the thermal model. The examples and diagrams in this manual are included solely for illustrative purposes. Users are cautioned that the information contained in this manual is subject to change at any time and without prior notice. In no event will responsibility or liability be accepted for direct or indirect or consequential damages resulting from the use or application of this equipment. TMS7 SERIES ME00070B 3 GENERAL DESCRIPTION 2.2 Part Number Format General Description TMS7- 2.1 Feature List - - - Enclosure E0 = IP00 E4 = IP42 Control Supply Voltage C24 = 230 VAC & 400 VAC C45 = 460 VAC & 575 VAC Supply Voltage V5 = 200 VAC ~ 525 VAC V7 = 200 VAC ~ 690 VAC Nominal kW Ratings (@ AC53a 3- 30:70-10) eg. 4022 = 22kW Starting • Current Limit mode. • Ramp Start mode. Stopping • Soft stop. • Pump stop. • Soft braking. Protection • Overcurrent protection. • Motor thermistor input. • Current imbalance. • Phase rotation. • Stall protection. • Undercurrent. • Supply frequency. • Shorted SCR. • Power circuit. • Motor connection. • RS485 failure. Interface • Remote control inputs (4 x fixed). • Relay outputs (1 fixed, 3 x programmable). • 4-20mA output (1 x fixed). • RS485 link. Human Interface • Local push buttons. (Start, Stop, Reset, Local/Remote) • Local programming buttons. (Function,Up,Down, Store) • LED parameter display • Phase indicator LEDs Power connection. • 3 Wire • 6 Wire • Bypass connections to retain motor protection even when bypassed. • 17 Amps to 1562 Amps (3 Wire) 26 Amps to 2345 Amps (6 Wire) • 200VAC to 525VAC (V5 models) • 200VAC to 690VAC (V7 models) Sundry features • IP42 (<253 Amps) • IP00 (>302 Amps) • Current read-out • Motor temperature read-out • Fault History (eight position). • Multiple function sets. • Restart Delay. • Low current alarm. • High current alarm. • Motor overtemperature alarm. • Auto-reset. • Function lock/Password protection. • Load defaults function settings. 4 ME00070B TMS7 SERIES SPECIFICATIONS Specifications 3.1 Current Ratings TMS7-4007 TMS7-4015 TMS7-4018 TMS7-4022 TMS7-4030 TMS7-4037 TMS7-4045 TMS7-4055 TMS7-4075 TMS7-4090 TMS7-4110 TMS7-4132 TMS7-4150 TMS7-4185 TMS7-4220 TMS7-4250 TMS7-4315 TMS7-4400 TMS7-4500 TMS7-4600 TMS7-4700 TMS7-4800 TMS7 SERIES 17 33 38 44 67 87 94 123 137 198 236 244 302 405 513 585 628 775 897 1134 1385 1563 15 29 34 39 58 75 81 106 119 171 204 211 267 361 456 524 568 710 831 989 1210 1366 14 26 30 35 51 66 71 93 105 151 179 186 233 313 393 450 489 606 706 872 1066 1202 AC53a 3-10:70-10 45oC <1000 metres 12 22 26 30 45 58 62 81 92 132 156 164 201 267 331 376 412 502 578 759 921 1030 TMS7-4007 TMS7-4015 TMS7-4018 TMS7-4022 TMS7-4030 TMS7-4037 TMS7-4045 TMS7-4055 TMS7-4075 TMS7-4090 TMS7-4110 TMS7-4132 TMS7-4150 TMS7-4185 TMS7-4220 TMS7-4250 TMS7-4315 TMS7-4400 TMS7-4500 TMS7-4600 TMS7-4700 TMS7-4800 ME00070B 26 50 57 66 101 131 141 185 206 297 354 366 453 608 770 878 942 1163 1346 1701 2078 2345 Start Current (%FLC) 350% 400% 23 44 51 59 87 113 122 159 179 257 306 317 401 542 684 786 852 1065 1247 1484 1815 2049 21 39 45 53 77 99 107 140 158 227 269 279 350 470 590 675 734 909 1059 1308 1599 1803 450% AC53a 4.5-30:70-10 45oC <1000 metres 300% AC53a 4-20:70-10 45oC <1000 metres 450% AC53a 4.5-30:70-10 45oC <1000 metres AC53a 4-20:70-10 45oC <1000 metres Start Current (%FLC) 350% 400% AC53a 3.5-15:70-10 45oC <1000 metres AC53a 3-10:70-10 45oC <1000 metres 300% Continuous Operation (Not Bypassed), 6 Wire Connection AC53a 3.5-15:70-10 45oC <1000 metres Continuous Operation (Not Bypassed), 3 Wire Connection 18 33 39 45 68 87 93 122 138 198 234 246 302 401 497 564 618 753 867 1139 1382 1545 5 SPECIFICATIONS TMS7-4007 TMS7-4015 TMS7-4018 TMS7-4022 TMS7-4030 TMS7-4037 TMS7-4045 TMS7-4055 TMS7-4075 TMS7-4090 TMS7-4110 TMS7-4132 TMS7-4150 TMS7-4185 TMS7-4220 TMS7-4250 TMS7-4315 TMS7-4400 TMS7-4500 TMS7-4600 TMS7-4700 TMS7-4800 6 18 34 41 47 67 88 96 125 141 202 238 254 302 405 513 585 628 775 897 1153 1403 1574 18 34 41 47 62 82 90 120 127 187 224 228 285 395 513 585 626 775 897 1153 1403 1574 16 34 41 47 54 71 78 103 111 162 194 198 245 336 435 504 528 672 798 1006 1275 1474 14 28 34 39 47 61 66 88 96 140 166 172 209 282 356 410 436 542 632 850 1060 1207 ME00070B TMS7-4007 TMS7-4015 TMS7-4018 TMS7-4022 TMS7-4030 TMS7-4037 TMS7-4045 TMS7-4055 TMS7-4075 TMS7-4090 TMS7-4110 TMS7-4132 TMS7-4150 TMS7-4185 TMS7-4220 TMS7-4250 TMS7-4315 TMS7-4400 TMS7-4500 TMS7-4600 TMS7-4700 TMS7-4800 27 51 62 71 101 132 144 188 212 303 357 381 453 608 770 878 942 1163 1346 1730 2105 2361 27 51 62 71 94 122 136 181 190 281 336 342 427 592 770 878 939 1163 1346 1730 2105 2361 450% AC53b 4.5-30:330 45oC <1000 metres Start Current (%FLC) 350% 400% AC53b 4-20:340 45oC <1000 metres 300% AC53b 3-10:350 45oC <1000 metres 450% AC53b 4.5-30:330 45oC <1000 metres AC53b 4-20:340 45oC <1000 metres Start Current (%FLC) 350% 400% AC53b 3.5-15:345 45oC <1000 metres AC53b 3-10:350 45oC <1000 metres 300% Bypassed Operation, 6 Wire Connection AC53b 3.5-15:345 45oC <1000 metres Bypassed Operation ,3 Wire Connection 24 51 62 71 82 106 117 155 166 243 290 297 368 504 653 756 793 1009 1197 1509 1912 2212 20 42 52 59 71 91 99 132 145 210 250 259 314 424 534 614 654 813 948 1276 1591 1811 TMS7 SERIES SPECIFICATIONS 3.2 Dimensions & Weights A B mm mm 3.3 C a b Wei ght mm mm mm Kg Semiconductor fuses can be used with the TMS7 to reduce the potential of damage to SCRs from transient overload currents and for Type 2 coordination. Suitable Bussman semiconductor fuses are detailed below. IP42/NEMA 1 TMS7-4007 TMS7-4015 TMS7-4018 TMS7-4022 TMS7-4030 TMS7-4037 TMS7-4045 TMS7-4055 TMS7-4075 TMS7-4090 TMS7-4110 TMS7-4132 TMS7-4150 TMS7-4185 TMS7-4220 TMS7-4250 TMS7-4315 TMS7-4400 TMS7-4500 TMS7-4600 TMS7-4700 TMS7-4800 380 185 180 365 130 6 380 185 250 365 130 7 425 270 275 410 200 17.5 425 390 275 410 IP00 300 23 F Series Fuses TMS7-4007 TMS7-4015 TMS7-4018 TMS7-4022 TMS7-4030 TMS7-4037 TMS7-4045 TMS7-4055 TMS7-4075 TMS7-4090 TMS7-4110 TMS7-4132 TMS7-4150 TMS7-4185 TMS7-4220 TMS7-4250 TMS7-4315 TMS7-4400 TMS7-4500 TMS7-4600 TMS7-4700 TMS7-4800 42 690 430 294 522 320 49 855 574 353 727 500 120 TMS7-4007 ~ TMS7-4132 o 6 .5 A 170M Series Fuses TMS7-4007 TMS7-4015 TMS7-4018 TMS7-4022 TMS7-4030 TMS7-4037 TMS7-4045 TMS7-4055 TMS7-4075 TMS7-4090 TMS7-4110 TMS7-4132 TMS7-4150 TMS7-4185 TMS7-4220 TMS7-4250 TMS7-4315 TMS7-4400 TMS7-4500 TMS7-4600 TMS7-4700 TMS7-4800 o 12 .0 a o 6 .5 b B C TMS7-4150 ~ TMS7-4800 o 9 .0 o 16 A a o 9 .0 b B Semiconductor Fuses C ≤415VAC 63AFE 160AFEE 200FM 200FM 200FM 250FM 250FM 250FM 280FM 500FMM 630FMM 630FMM 630FMM 500FMM 700FMM *500FMM *500FMM *700FMM - Supply Voltage ≤525VAC ≤575VAC 63AFE 63AFE 160AFEE 160AFEE 180FM 180FM 180FM 180FM 180FM 180FM 250FM 250FM 250FM 250FM 250FM 250FM 280FM 280FM 450FMM 450FMM 630FMM 630FMM 630FMM 630FMM 500FMM 500FMM 500FMM 500FMM 700FMM 700FMM *500FMM *500FMM *500FMM *500FMM *700FMM *700FMM - Starter I2 t ≤695VAC 63AFE 1,150 160AFEE 10,500 180FM 15,000 180FM 18,000 180FM 15,000 250FM 51,200 250FM 80,000 250FM 97,000 280FM 97,000 450FMM 145,000 630FMM 414,000 630FMM 414,000 500FMM 211,000 500FMM 320,000 700FMM 781,000 *500FMM 1,200,000 *500FMM 1,200,000 *700FMM 2,532,000 4,500,000 4,500,000 6,480,000 12,500,000 Supply Voltage ≤415VAC ≤525VAC ≤575VAC ≤695VAC 170M1315 170M1319 170M1319 170M1319 170M1319 170M3017 170M1322 170M1322 170M1322 170M6141 170M3023 170M3023 170M5144 170M6012 170M6014 170M5017 170M6019 170M6021 170M6021 170M6021 170M6021 170M6021 170M1314 170M1317 170M1318 170M1318 170M1318 170M3017 170M1321 170M1322 170M1322 170M6141 170M3023 170M3023 170M5144 170M4016 170M6014 170M6015 170M6018 170M6020 170M6020 170M6020 170M6021 170M6021 170M1314 170M1317 170M1318 170M1318 170M1318 170M3017 170M1321 170M1322 170M1322 170M6141 170M3023 170M3023 170M5144 170M6011 170M4018 170M6014 170M6017 170M6017 170M6151 170M6151 *170M5018 *170M5018 Starter I2 t 170M1314 1,150 170M1317 10,500 170M1318 15,000 170M1318 18,000 170M1318 15,000 170M3017 51,200 170M1321 80,000 170M1322 97,000 170M1322 97,000 170M6141 145,000 170M3023 414,000 170M3023 414,000 170M5144 211,000 170M6011 320,000 170M4018 781,000 170M6014 1,200,000 170M6017 1,200,000 170M6017 2,532,000 170M6151 4,500,000 170M6151 4,500,000 *170M5018 6,480,000 *170M5018 12,500,000 *Two parallel connected fuses required per phase TMS7 SERIES ME00070B 7 SPECIFICATIONS 3.4 Power Terminations 6 mm Outputs Run Output (R34,R33) .......... Normally Open, 5A @ 250VAC/360VA ................................................................... 5A @ 30VDC resistive Prog. Output A (R44,R43) ..... Normally Open, 5A @ 250VAC/360VA ................................................................... 5A @ 30VDC resistive Prog. Output B (R24,R23) .... Normally Open, 5A @ 250VAC/360VA, ................................................................... 5A @ 30VDC resistive Prog Output C (R14,R12,R11) ... Changeover, 5A @ 250VAC/360VA ....................................................................5A @ 30VDC resistive Analogue Output (C6,C7) .................................................. 4-20mA 6 mm 14 mm 3 mm 1 6 mm TMS7-4007~ TMS7-4022 (3.5 NM, 2.6 FT- LBS) 4 mm TMS7-4030~ TMS7-4055 (3.5 NM, 2.6 FT-LBS) 8 mm 8 mm 20 mm 5 mm 26 mm TMS7- 4075 (8.5 NM, 6.3 FT- LBS) 6 mm TMS7-4090 ~ TMS7-4110 (8.5 NM, 6.3 FT-LBS) 10.5 mm 10 mm 28 mm 6 mm 32 mm TMS7-4132 ( 17 NM, 12.5 FT- LBS) 13 mm TMS7-4150 ~ TMS7-4500 12.5 mm 51 mm 16 mm TMS7-4600 ~ TMS7-4800 3.5 General Technical Data Supply Supply voltage (V5 models) ...... 3 x 200~525VAC (3 Wire Connection) 3 x 200~440VAC (6 Wire Connection) Supply voltage (V7 models) .... 3 x 200~ 690VAC (3 Wire Connection) 3 x 200~440VAC (6 Wire Connection) Electronics Supply (C24 models) ................... 230VAC (+10%/-15%) or 400VAC (+10%/-15%) Electronics Supply (C45 models) ................... 460VAC (+10%/-15%) or 575VAC (+10%/-15%) Supply frequency (at start) ......................................... 50Hz (± 2Hz) or 60Hz (±2Hz) Supply frequency (during start) ...................... > 45Hz (50Hz supply) or > 55Hz (60Hz supply) Supply frequency (during run) .......................... >48Hz (50Hz supply) or > 58Hz (60Hz supply) Sundry Enclosure Rating TMS7-4007~4132 ........................ IP42 (NEMA 1) Enclosure Rating TMS7-4150~4800 ................. IP00 (Open Chassis) Rated short- circuit current (with semi-conductor fuses) ............ 100kA Rated insulation voltage ...................................................... 690 V Surges ......................................... 2kV line to earth, 1kV line to line Fast transients ...................................................... 2.0kV / 5.0 kHz Rated impulse withstand voltage ............................................ 2 kV Form designation .............................................................. Form 1 Electrostatic discharge ...... 4kV contact discharge, 8 kV air discharge Equipment class (EMC) ................................................... Class A1 Radio-frequency electromagnetic field 0.15 MHz - 80 MHz: 140dBµV .................................................................80 MHz - 1 GHz: 10 V/m Pollution degree ................................................ Pollution Degree 3 Operating Temperatures ............................................ -5oC / +60oC Relative Humidity ........................... 5 – 95% (max non condensing) 1 This product has been designed for class A equipment. Use of the product in domestic environments may cause radio interference, in which case the user may be required to employ additional mitigation methods. Standards Approvals CE ..................................................................... IEC 60947-4-2 UL1 ................................................................................ UL508 C-UL1 ............................................................. CSA 22.2 No.14 Cü .............................................. AS/NZS 3947-4-2, CISPR-11 1 Requires the use of semi-conductor fuses; is applicable for supply voltages up to 600V; excludes models TMS-4600 ~ TMS7-4800. Control Inputs Start (I34,I33) ................ Normally Open, Active 24VDC, 8mA approx. Stop (I22,I21) ............. Normally Closed, Active 24VDC, 8mA approx. Reset (I12,I11) ............ Normally Closed, Active 24VDC, 8mA approx. FLC Select (I44,I43) .......Normally Open, Active 24VDC, 8mA approx. 8 ME00070B TMS7 SERIES INSTALLATION Input/Output Installation Output Input 6.1 General Layout Diagrams TMS7-4007 ~ TMS7-4055 Input/Output Input Output To adjust the bus bar configuration first remove the TMS7 cover and main control module. Next loosen and remove the bus bar fixing bolts. The bus bars can then be removed and reinstalled into the starter in the desired configuration. The fixing bolts should then be refitted and tightened to a torque of 8.5NM. When re-orienting bus bars L1, L2, L3 the current transformers must also be relocated. TMS7-4075 ~ TMS7-4132 Care must be taken to ensure that foreign matter does not contaminate the jointing compound and become trapped between the bus bar and its mounting plate. If the paste does become contaminated, clean and replace with a jointing compound suitable for aluminium to aluminium, or aluminium to copper joints. 4.3 Mounting Instructions Models TMS7-4007 ~ 4132 can be wall mounted or installed inside another enclosure. These models can be mounted side by side with no clearance but a 100mm allowance must be made top and bottom for air intake and exhaust. 100mm Minimum Clearance 100mm Minimum Clearance 100mm Minimum Clearance 100mm Minimum Clearance 100mm Minimum Clearance 100mm Minimum Clearance TMS7-4150 ~ TMS7-4800 Models TMS7-4150 ~ 4800 have an IP00 rating and must be mounted in another enclosure. These models can be mounted side by side with no clearance but a 200mm allowance must be made top and bottom for air intake and exhaust. 200mm Minimum Clearance 200mm Minimum Clearance 4.2 Power Termination Configuration The bus bars on models TMS7-4150 ~ TMS7-4800 can be adjusted to provide four different input/output power terminal configurations. 200mm Minimum Clearance TMS7 SERIES ME00070B 200mm Minimum Clearance 9 INSTALLATION 4.4 Ventilation When installing TMS7 starters in an enclosure there must be sufficient air flow through the enclosure to limit heat rise within the enclosure. Temperature within the enclosure must be kept at, or below, the TMS7 maximum ambient temperature rating. If installing an TMS7 within a totally sealed enclosure a bypass contactor must be employed to eliminate heat dissipation from the soft starter during run. Soft starters dissipate approximately 4.5 watts per amp. The table below shows air flow requirements for selected motor currents. If other heat sources are installed in an enclosure along with the TMS7 an additional air flow allowance must be made for these items. Note that heat generation from semiconductor fuses, if used, can be eliminated by installing these within the bypass loop. Motor Amps 10 20 30 40 50 75 100 125 150 175 200 250 300 350 400 450 500 550 600 10 Heat (watts) 45 90 135 180 225 338 450 563 675 788 900 1125 1350 1575 1800 2025 2250 2475 2700 Required Airflow m3/min m3/hour 5oC 10oC 5oC 10oC Rise Rise Rise Rise 0.5 0.2 30 15 0.9 0.5 54 27 1.4 0.7 84 42 1.8 0.9 108 54 2.3 1.1 138 69 3.4 1.7 204 102 4.5 2.3 270 135 5.6 2.8 336 168 6.8 3.4 408 204 7.9 3.9 474 237 9.0 4.5 540 270 11.3 5.6 678 339 13.5 6.8 810 405 15.8 7.9 948 474 18.0 9.0 1080 540 20.3 10.1 1218 609 22.5 11.3 1350 675 24.8 12.4 1488 744 27.0 13.5 1620 810 ME00070B TMS7 SERIES POWER CIRCUITS Power Circuits Connect the three OUTPUT terminals (T1, T2, T3) of the TMS7 to the motor windings ensuring that the connections are made to one end of each winding only. It is imperative to connect the output of the TMS7 to the same end of each winding and this is usually marked on the motor terminations. 5.1 Overview TMS7 starters can be wired with a number of different power circuits depending on application requirements. L1 L2 L3 5.2 3 Wire Connection This is the standard connection format. Supply voltage is connected to the starter input terminals L1, L2 & L3. The motor cables are connected to the soft starter output terminals T1, T2 & T3. ( OPTI ONAL) K1 M (OPTIONAL ) F1 L1 T1 MOTOR TERMINALS 6 WIRE CONNECTION L1B L2 3 PHASE SUPPLY T2 M L2B L3 T3 The six terminations to the motor windings are usually arranged in two rows of three so that the links can be fitted across from the top three terminations to the lower terminations. In this case connect the TMS7 to the top terminations only. Connect the other three motor terminals to the input of the TMS7 in a manner that connects the end of each winding to a different phase from the input. This is most easily achieved by replacing each delta link in the motor terminal box by one phase of the controller. For example if the delta links are fitted U1-V2,V1-W2,W1-U2 - Connect the incoming phases to L1,L2,L3 on the TMS7. - Connect the TMS7 to the motor. T1-U1, T2-V1, T3-W1 - Connect the other motor terminals to the TMS7’S input W2-L1, U2-L2, V2-L3 L3B Legend T1 T2 T3 E K1 Line Contactor F1 Semiconductor Fuses 5.3 3 Wire Connection (Bypassed Operation) TMS7 starters can be bypassed while the motor is running. Special terminals (L1B, L2B, L3B) are provided for connection of the bypass contactor. Use of these terminals enables the TMS7 to continue to provide all protection and current monitoring functions even when bypassed. The TMS7 Run Output (Terminals R34 & R33) should be used to control operation of the bypass contactor. The bypass contactor can be AC1 rated for the motor full load current. K 2M 5.5 6 Wire Connection (Bypassed Operation) (OPTIONAL) K1M TMS7 units are capable of 6 Wire (Inside Delta) connection and can be bypassed. (O PT IONAL) F1 L1 T1 L1B L2 3 P HA SE SUPP LY T2 M K2 M L2B L3 T3 L3B E K1 M (OPTIONAL ) F1 L1 Run Output T1 L1B R33 Legend K1M Line Contactor K2M Bypass Contactor F1 Semiconductor Fuses 3 PHAS E S UP PLY R34 U1 L2 T2 L2B U2 M W1 L3 K2M V1 V2 W2 T3 L3B E 5.4 6 Wire Connection K 1M Line Con tactor K 2M Bypass Co ntacto r F1 Semiconductor Fuses TMS7 units are capable of 6 Wire (Inside Delta) connection as well as 3 Wire connection. When connected in this configuration the soft starter carries only phase current, this means the motor FLC current can be 50% greater than the soft starter’s FLC current rating. K1M 3 PHASE SUPPLY L2 U1 T2 L2B L3 Lege nd K1 Line Conta ctor F1 Se micon ducto r Fuses TMS7 SERIES V1 W1 K 2M CAUTION: Under no circumstance should power factor correction capacitors be connected between the CAUTION soft starter and the motor. Connecting power factor correction capacitors to the output of the soft starter will result in damage to the soft starter. U2 M R34 If static power factor correction is employed, it must be connected to the supply side of the soft starter. T1 L1 B Run Output 5.6 Power Factor Correction (OP TIO NA L) F1 L1 R33 Legend V2 W2 T3 L3B E ME00070B 11 POWER CIRUCITS 5.7 Line contactors The TMS7 is designed to operate with or without a line contactor. In many regions there is a statutory requirement that a line contactor be employed with electronic motor control equipment. From a safety point of view, this is the preferable option, however is not necessary for starter operation. An additional benefit gained by use of a line contactor is isolation of the starter SCR’s in the off state, when they are most susceptible to damage from voltage transients. The TMS7 can directly control a line contactor via the Main Contactor Control output. As an alternative to a line contactor, either a circuit breaker with a no volt release coil operated by the TMS7 trip output, or a motor operated circuit breaker can be considered. If a motor operated circuit breaker is used as a line contactor, the potential delay between the breaker being told to close and phase power being applied to the TMS7 could cause the TMS7 to trip on installation faults. Closing the motorized breaker directly and using the breaker’s auxiliary contacts, or preferably a slave relay with gold flash contacts, to control the TMS7 can avoid this. Line contactors must be selected such that their AC3 rating is equal to or greater than the full load current rating of the connected motor. 12 ME00070B TMS7 SERIES CONTROL CIRCUITS Control Circuits Input Voltages 6.1 Electrical Schematic (C45 L1 Models) T1 L2 T2 OR 5 75V C24 models +10 -15 400V +10 -15 2 30V OR FLC SELECT +10 -15 +10 -15 A1 A2 C3 GND C4 RS48 5 SERIAL INTERFACE A3 C5 I44 R44 PROGRAMMABLE R 43 OUTPUT A (Main Contactor) I43 R3 4 I3 4 START R33 I22 R23 I2 1 995-0083200 RUN OUTPUT Remote push button control PROGRAMMABLE OUTPUT B (Start/Run) I44 R 14 I12 R ESET 995-0083100 I3 3 R2 4 STOP 995-0082900 TMS7 operation can be controlled using either the local push buttons, remote control inputs or the serial communications link. The <LOCAL/REMOTE> push button can be used to switch between local and remote control. Refer to Function 20. Local/Remote Operation for details. Remote Control Inputs The TMS7 has four remote control inputs. Contacts used for controlling these inputs should be low voltage, low current rated (Gold flash or similar). E C45 models TMS7-4132~ TMS7-4800 6.3 Control Wiring T3 L3 B 460V TMS7-4030~ TMS7-4110 TO MOTOR L2 B L3 TMS7-4007~ TMS7-4022 110/230 VAC L1B 3 PHASE SUPPLY Part Number R12 I11 R11 I43 PROGRAMMABLE OUTPUT C I34 (Tripped) I33 MOTOR THERMISTOR C1 C6 C2 C7 I22 4-20 mA OUTPUT (MOTOR CUR RENT) I21 I12 I11 6.2 Control Supply R44 R43 R34 (C24 Models) 110/460 VAC 110/575 VAC TMS7 SERIES R24 TMS7-4132~ TMS7-4800 995-0082100 995-0082500 995-0082300 995-0082700 995-0082400 995-0082800 I 33 I 22 I 21 I 12 I 11 Start Stop Reset The TMS7 provides four relay outputs, one fixed and three programmable. Functionality of the programmable outputs is determined by the settings of Functions 21, 22 & 23. Part Number TMS7-4030~ TMS7-4110 Reset I 34 FLC Select Relay Outputs R33 TMS7-4007~ TMS7-40047 Stop I 43 Ensure cables to the control inputs are segregated from AC power and control wiring. Maximum VA 11VA 18VA 24VA 41VA 56VA For circumstances where the available control supply voltage is not suitable for direct connection to the TMS7 the following range of auto-transformers are available as accessories. These auto-transformers can be mounted within the TMS7 in models. Input Voltages Start I 44 CAUTION: Do not apply voltage to the control inputs. The inputs are active 24VDC and must be controlled with potential free circuits. CAUTION Ensure contacts/switches operating the control inputs are suitable for low voltage, low current switching ie, gold flash or similar. Voltage must be connected to the TMS7 control voltage terminals. The required control voltage is dependent upon the TMS7 model ordered. • TMS7xxxx-xx-C24-xx models: 230VAC (A2-A3) or 400VAC (A1-A2) • TMS7xxxx-xx-C45-xx models: 460VAC (A1-A2) or 575VAC (A2-A3) TMS7 Model TMS7-4007~TMS7-4022 TMS7-4030~TMS7-4055 TMS7-4075~TMS7-4110 TMS7-4132~TMS7-4500 TMS7-4600~TMS7-4800 FLC Select Two wire control R23 R14 R12 R11 Programmable Output A (*Main Contactor) Run Output Programmable Output B (*Start/Run) Programmable Output C Functionality Assignmen - Tripped - Overcurrent trip - Undercurrent trip - Motor thermistor trip - St arter overt emperature t - Phase imbalance trip - Electronic shearpin trip - Low current alarm - High current alarm - Motor overload alarm - St art/Run - Main Contactor (*Tripped) * = default functionality ME00070B 13 CONTROL CIRCUITS Host controller to TMS7 Start signal START Output voltage SEND TMS7 S LAV E ADDRES S N RELAY FUNCTIONS ACK N RECEIV ED Main contactor TIMEOUT Y Y D Start/Run DATA/ C COMMA ND SE ND REQUEST SEND COMM AND Run Y TI MEOUT Pre-start Tests C1 C2 Thermistor Input Motor thermistors C1 C2 Thermistor Input N ACK N RECEIV ED DATA RECI EVE D Y Y N LRC VALID Y LRC ERROR TIME OUT ERROR E ND TMS7 to host controller START NOTE: The thermistor circuit must be closed before the TMS7 will run. N EOT DETECT Y RECEIVE ADDRESS CAUTION The thermistor circuit should be run in screened N cable and must be electrically isolated from earth and all other power and control circuits. N ENQ EOT Y Y N L RC VALI D If no motor thermistors are connected to the TMS7 thermistor input there must be a link across the thermistor input terminals C1 & C2. Y N ADDRESS VALI D Y SEND ACK 6.4 RS485 Serial Communication N N STX EOT Y Y The TMS7 has a non-isolated RS485 serial communication link. RECEIVE DATA RS485 TIME OUT N RE CE IVE DATA Motor Thermistors Motor thermistors (if installed in the motor) may be connected directly to the TMS7. A trip will occur when the resistance of the thermistor circuit exceeds approximately 2.8kΩ. The TMS7 can be reset once the thermistor circuit resistance falls below approximately 2.8kΩ No motor thermistors Y N - C3 GND C4 N N Y EOT ETX Y + C5 N L RC VALI D SEND NAK Y NOTE: Power cabling should be kept at least 300mm away from communications cabling. Where this cannot CAUTION be avoided magnetic shielding should be provided to reduce induced common mode voltages. Data transmitted to and from the TMS7 must be in 8 bit ASCII, no parity, 1 stop bit. Baud rate is set by Function. 61 RS485 Baud Rate. The TMS7 can be programmed to trip if the RS485 link fails by setting Function 60. RS485 Timeout. The starter address is assigned using Function 62. RS485 Satellite Address. The flow charts below show typical form of communication between an TMS7 and host controller. 14 N SEND DATA CONTROL TMS7 Y SEND DATA SEND ACK The following code sequences are used in the communications between the host and the TMS7 (network). Address slave unit. ASCII EOT [nn] ENQ or 04h [n1]h [n2]h 05h LRC [LRC1]h [LRC2]h Slave response. ASCII ACK or 06h ME00070B TMS7 SERIES CONTROL CIRCUITS NOTE: If no TMS7 starter is configured to the specific slave address, no response will be received by the host. The host software timeout should be set to a CAUTION minimum of 250 ms. Status Read ASCII 6= 7= 8= 9= 10 = NOTE: Slave address must be two digit, addresses less than 10 must have a leading zero (0). 11 = CAUTION Master command to slave. ASCII STX [command] or 02h [c1]h [c2]h [c3]h Data Read ASCII Current D10 LRC [LRC1]h [LRC2]h ETX 03h Temp D12 [command] = 3 byte ASCII command (or request) selected from the tables below. LRC = Longitudinal Redundancy Check. Slave response if Command and LRC correct ASCII ACK or 06h Slave response of Read request correct and LRC correct. ASCII STX [data] LRC ETX or 02h [d3]h [d2]h [d1]h [d0]h [LRC1]h [LRC2]h 03h ASCII STX B 1 0 Each command, status or data request is a 3 byte string as detailed below. Invalid command/request strings cause the TMS7 to respond with a NAK (15h). ASCII Status_1 C12 Trip Version Trip Code C14 C16 C18 TMS7 SERIES C10 Comment Requests motor current. The data is 4 byte decimal ASCII. Minimum value 0000, Maximum value 9999 Amps. Requests the calculated value of the motor thermal model as a % of Motor Thermal Capacity. The data is 4 byte decimal ASCII. Minimum value 0000%. Trip point 0105%. For example Command String (Start); ASCII STX B 1 or 02h 42h 31h Slave response if Read request or LRC invalid. ASCII NAK or 15h Status Read Status Phase rotation trip Stall trip Power circuit fault Undercurrent trip Starter heatsink overtemperature Invalid motor connection Each command string sent to and from the TMS7 includes a check sum. The form used is the Longitudinal Redundancy Check (LRC) in ASCII hex. This is an 8-bit binary number represented and transmitted as two ASCII hexadecimal characters. To calculate LRC: 1. Sum all ASCII bytes 2. Mod 256 3. 2's complement 4. ASCII convert Slave response if Command and LRC incorrect ASCII NAK or 15h Command ASCII Start B10 Stop B12 Reset B14 Coast to B16 stop Comment Comment Initiates a start. Initiates a stop Resets a trip state Initiates an immediate removal of voltage from the motor. Any soft settings are ignored. Hex 02h 42h 31h 30h A5h A5h 5Ah 01h 5Bh ASCII 5 or 35h B 42h Binary 0000 0010 0100 0010 0011 0001 0011 0000 1010 0101 1010 0101 0101 1010 0101 1011 0101 1011 0 30h SUM (1) MOD 256 (2) 1's COMPLEMENT +1= 2's COMPLEMENT (3) ASCII CONVERT (4) LRC CHECKSUM The complete command string becomes ASCII STX B 1 0 5 or 02h 42h 31h 30h 35h Comment Requests the configuration status of the TMS7. Requests the operational status of the TMS7. Requests the trip status of the TMS7. RS485 protocol version number. 255 = No trip 0= Shorted SCR 1= Reserved 2= Motor Thermal model trip 3= Motor thermistor 4= Current imbalance trip 5= Supply frequency trip ME00070B B 42h ETX 03h To verify a received message containing an LRC; 1. Convert the last two bytes of message from ASCII to binary. 2. Left shift 2nd to last byte 4 bits. 3. Add this result to the last byte to get the binary LRC. 4. Add up all the bytes of the message, except the last two. 5. Add the binary LRC. 6. The least significant byte should be zero. For example: ASCII STX ETX B 1 0 5 B 15 CONTROL CIRCUITS or 02h 03h 42h 31h 30h 35h 42h Trip bits (negative logic 0 = true). The table below shows the complement of these bits to give positive logic (1 = true). Status Bit Function NOT Trip.7 Phase Loss NOT Trip.6 Undercurrent NOT Trip.5 Phase Rotation NOT Trip.4 Overcurrent NOT Trip.3 Over Temperature NOT Trip.2 Installation NOT Trip.1 Stall Protection NOT Trip.0 Thermistor 1. 35h (ASCII hex) = 5H = 00000101 42h (ASCII hex) = Bh = 00001011 Note: 03h is the EXT character (end of transmission) and is not part of the message. 2. 00000101 = 01010000 3. 01010000 + 00001011 = 01011011 4. 02h + 42h + 31h + 30h = A5h 5. A5h + 5Bh = 100h 6. The least significant byte is zero so the message and LRC match. Response or status bytes are sent from the TMS7 as an ASCII string. STX d1 = d2 = d3 = d4 = [d1]h [d2]h [d3]h [d4]h LRC1 LRC2 ETX 30h 30h 30h plus upper nibble of status byte right shifted by four binary places. 30h plus lower nibble of status byte. For example status byte = 1Fh, response is STX 30h 30h 31h 3Fh LRC1 LRC2 ETX Status bits (positive logic 1 = true) Status Function Comment Bit Status.7 50 Hz Only one of either Status.7 or Status.6 can be at logic 1 when the TMS7 is operating. Status.6 60 Hz Status.5 Unallocated Status.4 Soft stop Status.3 Positive Will be at logic 0 when there is a phase negative phase rotation. rotation Status.2 Unallocated Status.1 Unallocated Status.0 Unallocated Status_1 bits (negative logic 0 = true) Status Bit Function Comment NOT Status_1.7 NOT Status_1.6 NOT Status_1.5 NOT Restart Status_1.4 Delay NOT Overload Motor is operating in an overload Status_1.3 condition. NOT Run Status_1.2 NOT Output On Status_1.1 NOT Power On Status_1.0 16 ME00070B TMS7 SERIES PROGRAMMING Programming 7.1 Programming Procedure Step 1. 1. Enter program mode. Simultaneously press and release the <FUNCTION> and <STORE> keys. (When in program mode the three LEDs to the right of the numeric display will be illuminated.) Step 4. 1. 2. Step 2. 1. 2. 3. Press the <STORE> key to store the displayed setting into memory. Verify the new set point has been correctly stored by pressing and then releasing the <FUNCTION> key. The LED display should now show the new set point. Select the function number to be viewed or adjusted. Press and hold the <FUNCTION> key. Using the <UP> and <DOWN> keys select the required function number. (Function numbers are left justified and blink). When the required function number is dispalyed, release the <FUNCTION> key. The display changes to show the function set point currently stored in memory. (Function values are right justified and do not blink) Step 5. 1. Step 3. 1. Store the new function set point. Exit program mode. Once all function settings have been made, exit the programming mode by simultaneously pressing and releasing the <FUNCTION> and <STORE> keys. Alter the function set point. Review the current function set point and, if necessary, use the <UP> or <DOWN> keys to adjust the setting. (Pressing the <FUNCTION> key will restore the original setting). TMS7 SERIES ME00070B 17 PROGRAMMING 7.2 Function List No. Function Primary Motor Settings 1 2 3 4 5 6 7 8 9 Motor full load current Current limit Minimum current Start ramp time Stop ramp time Motor trip class Current imbalance sensitivity Undercurrent protection Stall protection 7.3 Default Setting 1. Soft stop mode Default Setting: Model Dependant (Amps) Description: Sets the TMS7 for the connected motor’s full load current. Adjustment: Set to the Full Load Current (amps) rating shown on the motor nameplate. 2. Local/Remote operation Relay output A functionality Relay output B functionality Relay output C functionality Default Setting: 350% FLC Description: Sets the current limit for the Constant Current start mode. 0 11 10 0 eg. Function 2. Current Limit = 350% x FLC Protection Settings 30 31 32 Phase rotation Restart delay Current imbalance Current Limit Range: 100 – 550 % FLC 0 Starter Functionality 20 21 22 23 Motor Full Load Current Range: Model Dependant (Amps) 350 350 1 0 10 5 20 400 Start/Stop Formats 10 Function Descriptions 700% 0 15 0 500% Set Points 40 41 42 43 Low current alarm High current alarm Motor temperature alarm Field calibration 50 105 80 100 300% Analogue Output (Motor Current - % FLC) 50 51 4-20mA output range - max 4-20mA output range - min 100% 100 0 50% Serial Communications 60 61 62 RS485 timeout RS485 baud rate RS485 satellite address 0 4 20 ( % Full Speed) Adjustment: The required setting for the Current Limit function is installation dependant and should be set such that: • The motor is supplied with sufficient start current to enable it to produce torque adequate to easily accelerate the connected load. • Desired starting performance is obtained. • TMS7 ratings are not exceeded. Auto Reset 70 71 72 73 80 81 82 83 84 85 86 87 88 Auto-reset - configuration Auto-reset - number of resets Auto-reset - group A & B delay Auto-reset - group C delay Secondary Motor Settings Motor full load current Current limit Minimum current Start ramp time Stop ramp time Motor trip class Current imbalance sensitivity Undercurrent protection Stall protection 0 1 5 5 350 350 1 0 10 5 20 400 3. Current imbalance trip delay Minimum Current Range: 100 – 550 % FLC Default Setting: 350% FLC Description: Sets the minimum current level for the Ramp Start mode. Function. 2 Current Limit = 350% x FLC Function. 3 Minimum Current = 200% x FLC Function. 4 Start Ramp Time = 10 secs Protection Delays 90 100% ROTOR SPEED 700% 3 Read Only Data 100 Model Number 101 Fault History - 500% Restricted Functions 110 111 112 113 Access code Update access code Function lock Restore function settings 0 0 0 0 300% 100% 50% 100% ROTOR SPEED (% Full Speed) 18 ME00070B TMS7 SERIES PROGRAMMING Adjustment: Function 3 Minimum Current and Function 4 Start Ramp Time are used together to activate and control the Ramp Start mode. If the Ramp Start mode is required, set the Minimum Current so that the motor begins to accelerate immediately a start is initiated. Ramp Start mode is not required, set the Minimum Current equal to the Current Limit. Ramp Start mode should be considered in preference to Current Limit start mode in applications where: • Required start torque can vary from start to start. For example conveyors may start loaded or unloaded. In this case set Function 3 Minimum Current to a level that will start motor in the light load condition and Function 2 Current Limit to a level that will start the motor in the high load condition. • Starting time of an easily broken away load needs to be extended, for example pumps. • A generator set supply is limited and a slower application of load will allow greater time for the generator set to respond. 4. Time or Maximum DOL Start Time. This information is available from the motor data sheet or direct from the motor supplier. NOTE: The TMS7 motor thermal model assumes a locked rotor current of 600%. If the connected CAUTION motor’s locked rotor current differs from this, greater accuracy can be achieved by using a normalised MTC figure. A normalised MTC figure can be calculated as follows: 2 %LRC MTC = X Max Start Time 600 NOTE: Setting Function 6 Motor Trip Class according to the motor’s actual thermal capacity allows CAUTION safe use of the motor’s full overload capability both to start the load and ride through overload conditions. Additionally, a more conservative approach can be taken by setting a reduced MTC for easy to start loads that will not experience transient operating overloads as a part of normal operation. Using a reduced MTC figure has the advantage of maximising motor life. The life of a motor is strongly influenced by its maximum winding temperature, with a 'rule of thumb' stating that the expected life span of a motor is halved for every ten degree rise in temperature. The temperature rise is dependent on the motor losses and the motor cooling. The highest stress on the motor is during start, and can be minimised by restricting the duration and frequency of starts. A reduced MTC setting (Function 6) will also cause the TMS7 protection to operate before the motor is thermally stressed. Start Ramp Time Range: 1 – 30 Seconds Default Setting: 1 Second Description: Sets the ramp time for the Current Ramp start mode. Adjustment: Set the Start Ramp Time to optimise start performance. 5. Stop Ramp Time Range: 0 – 100 Seconds Default Setting: 0 Second (Off) Description: Sets the soft stop ramp time for soft stopping of the motor. Adjustment: Set the Stop Ramp Time to produce the desired motor stopping performance. Two soft stop modes are provided by the TMS7. Use Function 10. Soft Stop Mode to select the desired mode. A suitable reduced MTC figure can be established by observing the modeled motor temperature as shown on the TMS7 LED display, and adjusting the MTC parameter such that after a normal start which has been preceded by a period of running at maximum load, the calculated motor temperature is approaching 90%. t(s) If utilising the Soft Stop function and a line contactor, the contactor must not be opened until the end of the stop ramp time. The TMS7 programmable outputs A,B or C can be set for control of the line contactor. Refer Functions 21, 22, 23 for programmable output assignment details. Cold start curves 10000 6. Motor Trip Class Range: 0 – 60 Seconds Default Setting: 10 Seconds 1000 NOTE: A setting of 0 seconds disables the TMS7 motor thermal model. Use this setting only if another form CAUTION of motor protection is used. Description: Sets the motor thermal capacity used by the TMS7 motor thermal model. Adjustment: Set the Motor Trip Class (MTC) according to the motor’s thermal capacity. 100 MTC = 10 Sec MTC = 5 Sec A motor’s thermal capacity is expressed as the maximum time (seconds) a motor can maintain locked rotor current conditions from cold, and is often referred to as Maximum Locked Rotor TMS7 SERIES MTC = 30 Sec MTC = 20 Sec 10 1 100 ME00070B 300 500 700 I (% FLC) 19 PROGRAMMING 7. 1 = TMS7 Local/Remote push button disabled while motor running. 2 = Local control only. (TMS7 push buttons enabled, remote inputs disabled) 3 = Remote control only. (TMS7 push buttons disabled, remote inputs enabled) Default Setting: 0 (Local/Remote button enabled) Current Imbalance Sensitivity Range: 1 – 10 1 = Highest sensitivity (lowest imbalance) I 5 = Average sensitivity I 10 = Lowest sensitivity (highest imbalance) Description: Sets the sensitivity of the current imbalance protection. Description: Enables and disables the local push buttons and remote control inputs. Also determines when and if the Local/Remote push button can be used to switch between local and remote control. Adjustment: Set as required Adjustment: The factory setting is suitable for most applications however the sensitivity can be adjusted to accommodate site specific tolerances 21. Default Setting: 5 8. Relay Output A Functionality Range: 0 –11 0 = Tripped 1 = Overcurrent trip 2 = Undercurrent trip 3 = Motor thermistor trip 4 = Starter overtemperature trip 5 = Phase imbalance trip 6 = Electronic shearpin trip 7 = Low current alarm 8 = High current alarm 9 = Motor overload alarm 10 = Start/Run 11 = Main contactor. Undercurrent Protection Range: 15% – 100% FLC Default Setting: 20% FLC Description: Sets the trip point for the TMS7 undercurrent protection as a percentage of motor full load current. Adjustment: Set to a level below the motors normal working range and above the motor’s magnetising (no load) current. To disable the undercurrent protection make a setting less than the magneti sing current of the motor, typically 25% - 35% of rated Full Load Current. NOTE: Undercurrent protection is only operative during ‘run’. Start signal Output voltage CAUTION 9. Stall Protection RELAY FUNCTIONS Range: 80% – 550% FLC Main contactor Default Setting: 400% FLC Description: Sets the trip point for the TMS7 stall protection as a percentage of motor full load current. Adjustment: Set as required. Start/Run Run Pre-start Tests NOTE: Stall protection is operative only during ‘run’. Default Setting: 11 (Main Contactor) Description: Assigns the functionality of programmable relay output A. Adjustment: Set as required CAUTION 10. Soft Stop Mode 22. Range: 0 – 1 0 = Standard soft stop 1 = Pump control Range: 0 - 11 Default Setting: 10 (Start/Run) Default Setting: 0 (Standard soft stop) Description: Assigns the functionality of programmable relay output B. Description: Sets the active soft stop mode. Adjustment: The standard soft stop mode automatically monitors motor deceleration and will provide optimum control for most applications. Pump control may however offer superior performance in some applications and can be of particular benefit in some pumping applications. Adjustment: Refer Function 21 Relay Output A Functionality for adjustment detail. 23. Relay Output C Functionality Range: 0 - 11 Default Setting: 0 (Tripped) 20. Local/Remote Operation Range: 0 – 3 0 = TMS7 Local/Remote push button always enabled. 20 Relay Output B Functionality Description: Assigns the functionality of programmable relay output C. ME00070B TMS7 SERIES PROGRAMMING Adjustment: Refer Function 21 Relay Output A Functionality for adjustment detail. 30. Adjustment: The motor overtemperature alarm can be assigned to the Programmable Relay Outputs A, B or C for indication of a motor temperature (as calculated by the Motor Thermal Model) in excess of the programmed value. A trip condition occurs when motor temperature reaches 105%. Phase Rotation Range: 0 – 2 0 = Off (forward and reverse rotation accepted) 1 = Forward rotation only (reverse rotation prohibited) 2 = Reverse rotation only (forward rotation prohibited) Default Setting: 0 (Off) 43. Default Setting: 100% Description: Sets the valid phase rotations for the TMS7 phase rotation protection. The TMS7 examines the incoming three phases and trips if phase rotation does not match the allowable rotations specified by Function 30. Description: Adds a gain to the TMS7 current monitoring circuits. The TMS7 is factory calibrated with an accuracy of ± 5%. The field calibration function can be used to match the TMS7 current readout with an external current metering device. Adjustment: Use the following formula to calculate the setting required. Current shown on TMS7 display Field Calibration = (Function 43) Current measured by external device Adjustment: Set as required. 31. Field Calibration Range: 85% - 115% Restart Delay Range: 1 – 254 seconds Default Setting: 15 Second Description: Sets the minimum time between the end of a stop and the beginning of the next start. Adjustment: Set as required. During the restart delay period the LEDs to the right of the TMS7 LED display will flash indicating the motor cannot yet be restarted. 32. e.g. 112 Amps CAUTION 50. 4-20mA Output Range - Max Range: 0 – 255% Description: Enables or disables the phase imbalance protection. Adjustment: Set as required. Default Setting: 100 % Description: Determines the value represented by a 20mA signal from the analogue output. Adjustment: Set as required to show percentage of motor current. Low Current Alarm Range: 1 – 100% FLC Default Setting: 50% FLC 51. Description: Sets the current level (% FLC) at which the low current alarm operates. 4-20mA Output Range - Min Range: 0 – 255% Default Setting: 0 % Adjustment: The low current alarm can be assigned to the Programmable Relay Outputs A, B or C for indication of a motor current lower than the programmed value. 41. 108 Amps NOTE: All current based functions are affected by this adjustment. Current Imbalance Range: 0 – 1 0 = On 1 = Off Default Setting: 0 (On) 40. 96% = Description: Determines the value represented by a 4mA signal from the analogue output. Adjustment: Set as required to show percentage of motor current. High Current Alarm Range: 50 – 550% FLC Default Setting: 105% FLC 60. Description: Sets the current level (% FLC) at which the high current alarm operates. Range: 0 – 100 Seconds Adjustment: The high current alarm can be assigned to the Programmable Relay Outputs A, B or C for indication of a motor current in excess of the programmed value. Description: Sets the maximum allowable period of RS485 serial inactivity. Adjustment: Set as required. 42. Default Setting: 0 seconds (Off) NOTE: A setting of 0 seconds disables the RS485 – Timeout Protection and enables the TMS7 to CAUTION continuing operating even if the RS485 link becomes inactive. Motor Temperature Alarm Range: 0 – 105% Motor Temperature Default Setting: 80% Description: Sets the temperature (%) at which the motor overtemperature alarm operates. TMS7 SERIES RS485 Timeout ME00070B 21 PROGRAMMING 61. Description: Sets maximum number of reset attempts for the Auto-reset function. Adjustment: The Auto-reset counter increases by one after each trip, up to the maximum number of resets set in Function 71. Auto-Reset – Number Of Resets. The fault is then latched and a manual reset is required. The Auto-reset counter decreases by one, to a minimum of zero, after each successful start/stop cycle. Refer Function 70 Auto-Reset – Configuration for further detail. RS485 Baud Rate Range: 1 – 5 1 = 1200 baud 2 = 2400 baud 3 = 4800 baud 4 = 9600 baud 5 = 19200 baud Default Setting: 4 (9600 baud) Description: Sets the baud rate for RS485 serial activity. 72. Adjustment: Set as required. Auto-Reset – Group A & B Delay Range: 5 – 999 seconds 62. RS485 Satellite Address Default Setting: 5 seconds Range: 1 - 99 Description: Sets the delay for resetting of Group A & B trips. Default Setting: 20 Adjustment: Refer Function 70 Auto-Reset – Configuration for further detail. Description: Assigns the TMS7 an address for RS485 serial communication. Adjustment: Set as required. 70. 73. Range: 5 – 60 minutes Auto-Reset - Configuration Default Setting: 5 minutes Description: Sets the delay for resetting of Group C trips. Adjustment: Refer Function 70 Auto-Reset – Configuration for further detail. Range: 0 – 3 0 = Off 1 = Reset Group A trips 2 = Reset Group A & B trips 3 = Reset Group A, B & C trips Default Setting: 0 (Off) Description: Determines which trips will be automatically reset. TMS7 soft starters can be programmed with two separate sets of motor data. The primary motor settings are adjusted using Functions 1 ~ 9. The secondary motor settings are adjusted using Functions 80 ~ 88. When commanded to start the TMS7 checks the state of the FLC Select input (Terminals I43 & I44). In the event of an open circuit the primary motor settings are used. In the event of a closed circuit the secondary motor settings are used. Adjustment: A setting of other than 0 causes the TMS7 to automatically reset, and after a delay if the start signal is still present, attempt to start the motor. The Auto-reset function can be programmed to reset faults according to the table below: Trip Group A B C Auto-Reset – Group C Delay Trip Conditions Phase imbalance, Phase loss Undercurrent, Electronic shearpin Overcurrent, Motor thermistor, Starter overtemperature 80. Motor Full Load Current Range: Model Dependant (Amps) Default Setting: Model Dependant (Amps) Operation of the Auto-reset function is controlled according to the following function settings: Description: Sets the TMS7 for the connected motor’s full load current. Adjustment: Refer to Function 1 for further detail. Function 70. Auto-reset – Configuration Function 71. Auto-reset – Number of resets Function 72. Auto-reset – Group A & B Delay Function 73. Auto-reset – Group C Delay 81. Range: 100 – 550 % FLC Default Setting: 350% FLC Description: Sets the current limit for the Constant Current start mode. CAUTION: Operation of the auto-reset function will reset a trip state and if the start signal is still present, CAUTION allow the motor to restart. Ensure that personal safety is not endangered by such operation and that all relevant safety measures and/or regulations are complied with before utilising this function. 71. Adjustment: Refer to Function 2 for further detail. 82. Minimum Current Range: 100 – 550 % FLC Default Setting: 350% FLC Description: Sets the minimum current level for the Ramp Start mode. Adjustment: Refer to Function 3 for further detail. Auto-Reset – Number Of Resets Range: 1 - 5 Default Setting: 1 22 Current Limit ME00070B TMS7 SERIES PROGRAMMING 83. Default Setting: 3 Seconds Start Ramp Time Description: Sets the delay period between detection of a phase imbalance greater than allowed by the setting made in Function 7 & 86. Current Imbalance Sensitivity and a trip condition. Adjustment: Set as required. Range: 1 – 30 Seconds Default Setting: 1 Second Description: Sets the ramp time for the Current Ramp start mode. Adjustment: Refer to Function 4 for further detail. 84. 100. Stop Ramp Time Range: 1 - 22 Default Setting: Model Dependant Range: 0 – 100 Seconds Default Setting: 0 Second (Off) Description: A diagnostic parameter used to identify the power assembly type. Description: Sets the soft stop ramp time for soft stopping of the motor. Adjustment: Refer to Function 5 for further detail. 85. 101. Default Setting: n/a Description: Displays the TMS7 Fault History. Adjustment: Use the <UP> and <DOWN> keys to scroll through the trip log. Refer to Section 9, Trouble Shooting Procedure for a description of the trip log and fault conditions. Default Setting: 10 Seconds NOTE: A setting of 0 seconds disables the TMS7 motor thermal model. Use this setting only if another form of motor protection is used. CAUTION Description: Sets the motor thermal capacity used by the TMS7 motor thermal model. Adjustment: Refer to Function 6 for further detail. 110. Default Setting: 0 Description: Entering the correct password does two things 1. Temporarily changes the function lock to Read/Write irrespective of the state specified by Function 112 Function Lock. This allows function settings to be adjusted during the current programming session. On exit of the current programming session function settings are again protected according to Function 112. Function Lock. 2. Provides access to parameters 111 - 113. Adjustment: Enter password. The default password is 0. Contact your supplier if the password is lost or forgotten Current Imbalance Sensitivity Default Setting: 5 Description: Sets the sensitivity of the current imbalance protection. 111. Default Setting: 0 Description: Changes the current password. Adjustment: Set as required, remembering to make note of the new password. Undercurrent Protection Range: 15% – 100% FLC Default Setting: 20% FLC 112. Description: Sets the trip point for the TMS7 undercurrent protection as a percentage of motor full load current. Adjustment: Refer to Function 8 for further detail. Stall Protection Default Setting: 400% FLC Description: Sets the trip point for the TMS7 stall protection as a percentage of motor full load current. Adjustment: Refer to Function 9 for further detail. 113. Current Imbalance Trip Delay Restore Function Settings Range: 0, 50 Range: 3 – 254 Seconds TMS7 SERIES Function Lock Range: 0 – 1 0 = Read/Write 1 = Read Only Default Setting: 0 (Read / Write) Description: Allows protection of all function settings. Note that when this function has been changed from 0 (Read/Write) to 1 (Read Only) the new setting takes effect only when program mode is exited. Adjustment: Set as required. Range: 80% – 550% FLC 90. Update Password Range: 0 - 999 Adjustment: Refer to Function 7 for further detail. 88. Password Range: 0 - 999 Range: 1 – 10 1 = Highest sensitivity (lowest imbalance) I 5 = Average sensitivity I 10 = Lowest sensitivity (highest imbalance) 87. Fault History Range: n/a Motor Trip Class Range: 0 – 60 Seconds 86. Model Number ME00070B 23 PROGRAMMING Default Setting: 0 Description: Allows function adjustments be returned to the factory defaults. Adjustment: Set to 50 to load default parameter settings. 7.4 Operation Once installed, wired and programmed according to the instructions earlier in this manual the TMS7 can be operated. Local control panel. 1. 2. 3. Numeric LED Display: The information being displayed is indicated by the LEDs to the right of the display. During operation either motor current (Amps) or the calculated motor temperature (%) can be displayed. Use the <UP> or <DOWN> keys select what information is displayed. In the event of a trip state the relevant trip code will be shown. If motor current exceeds the maximum current able to be shown on the numeric display, the display will show dashes. Starter Status LEDs: Start: Voltage is being applied to the motor terminals. Run: Full voltage is being applied to the motor terminals. Trip: The TMS7 has tripped. Remote: The TMS7 is in remote control mode. Operational Push Buttons: These push buttons can be used to control TMS7 operation when in local control mode. The <LOCAL/REMOTE> push button can be used to switch between local and remote control. NOTE: When control power is applied to the TMS7 it may be in either local or remote control mode according to the mode it was in when control power was CAUTION removed. The factory default is local control. 24 ME00070B TMS7 SERIES PROGRAMMING NOTE: Function 20. Local/Remote Operation can be used to limit operation to either local or remote mode operation. If the <LOCAL/REMOTE> push button is CAUTION used in an attempt to switch to a prohibited mode the numeric display will show 'OFF'. NOTE: Simultaneously pressing the <STOP> and <RESET> push buttons causes the TMS7 to immediately remove voltage from the motor, CAUTION resulting in a coast to stop. Any soft settings are ignored. circuit the primary motor settings are used. In the event of a closed circuit the secondary motor settings are used. Primary Motor Settings Function Settings 1 ~ 9 I44 Primary Motor Settings Function Settings 80 ~ 88 I44 I43 I43 FLC Select FLC Select 4. Programming Buttons: Refer to section 7.1. 5. Remote Control Inputs Status: These LEDs indicate the state of the circuits across the TMS7 remote control inputs. NOTE: All LEDs and the Numeric display are illuminated for approx imately 1 second to test their operation CAUTION when control power is first applied . Remote control. TMS7 operation can be controlled via the remote control inputs when the soft starter is in remote mode. Use the <LOCAL/REMOTE> push button to switch between local and remote modes. Refer to section 6.3 Control Wiring for further detail. Restart delay. Function 31. Restart Delay sets the delay period between the end of a stop and the beginning of the next start. During the restart delay period the LEDs to the right of the numeric display will flash indicating that a restart cannot yet be attempted. Pre-start tests. Before applying voltage to the motor when a start is initiated, the TMS7 first performs a series of tests to check the motor connection and supply conditions. Secondary motor settings. TMS7 starters can be programmed with two motor parameter sets. The primary motor parameters are set using functions 1~9. The secondary motor parameters are set using functions 80~88. When commanded to start the TMS7 checks the state of the FLC Select input (Terminals I43 & I44). In the event of an open TMS7 SERIES ME00070B 25 APPLICATION EXAMPLES Application Examples 8.1 Installation With Line Contactor K1M F1 8.2 Installation With Bypass Contactor K1M L1 T1 L1B L2 3 PHASE SUPPLY T2 TO MOTOR L2B F1 L3 460V OR 575V +10 -15 +10 -15 C24 mo dels 400V OR 230V +10 -15 +10 -15 E A1 A2 A3 C3 G ND L3 C4 TO MO TOR T3 L3B C5 E C4 5 mod els CO NT ROL SUPPLY R43 R34 T2 L2B R44 I34 L2 3 PHASE SUPPLY I44 I43 T1 L1B L3B C45 mode ls L1 T3 460V OR 575V K1M C 24 mo dels +10 -15 400V +10 -15 230V OR A1 +10 -15 A2 +10 -15 A3 C3 GND C4 C5 R33 I33 S1 I22 R24 I44 R23 I43 I21 S2 I12 I11 R34 R14 S3 R12 C1 C6 C2 C7 I34 R24 S2 I2 2 I21 S1 I12 I11 Legend K1M S1 S2 F1 Line Contactor Start Contact Reset Pushbutton Semiconductor Fuses (optional) MOT OR THERMIST OR Description: The TMS7 is applied with a line contactor (AC3 rated). The line contactor is controlled by the TMS7 Main Contactor output, which by default is assigned to RELAY OUTPUT A (terminals R44, R43). The control supply must be sourced from before the contactor. K1M R23 R14 R12 R11 C1 C6 C2 C7 L egend K1M Bypass Co ntactor S1 Reset Pushbutton S2 Stop Pushbutton S3 Start Pushbutton F1 Semi conductor Fuses (optional) Description: The TMS7 is applied with a bypass contactor (AC1 rated). The bypass contactor is controlled by the TMS7 RUN OUTPUT (terminals R34, R33). Function Settings: Function 21. Relay Output A Functionality = 11 (Assigns the Main Contactor function to Relay Output A) 26 CONT ROL SUPPLY R33 I33 R11 MOTOR THERMISTOR R44 R43 Function Settings: - no special settings required. ME00070B TMS7 SERIES APPLICATION EXAMPLES 8.3 Soft Braking 3 PHASE SUPPLY CO NTR OL SUPPLY THERMISTO R IN PUT A1 A2 A3 CONTROL SUPPLY C1 C2 THERMISTO R IN PUT F1 L1 L2 L3 FLC SELECT START T1 T2 T3 E I44 K3 A K2M I 43 I34 I33 STO P I2 2 K2A R11 RELAY OUTPUT C RESET I 21 I12 I11 R12 S3 K1 A K3A S2 K2T K1T S1 K4 A CON TRO L SUPPLY A2 K1 M K1 A K1M K2M K1A K1 M Y1 Y2 CO NTACTORS TO BE MECHANICAL LY INTERL OCKED K1 M K2M K1A K2A K3A K1T K2M Y1 K2 T Y2 K4 A M1 LEG EN D A2 F1 K1 A K2 A K3 A K4 A SHAFT RO TATION SEN SO R SEMI -CO NDUCTOR FUSES ( OPTION AL) RUN RELAY START RELAY BRAKE RELAY ROTATIO N SENSING REL AY K1M K2M K1T K2T S1 S2 S3 LINE CONTACTO R ( RUN) LINE CONTACTO R ( BR AKE) RUN DEL AY TIMER BR AKE DELAY TI MER START PUSHBUTTO N STOP PU SHBUTTON RESET PUSHBU TTON Description: For high inertia loads that require more braking torque than is available from the D.C.Brake feature, the TMS7 can be configured for 'Soft Braking'. In this application the TMS7 is employed with forward run and braking contactors. On receipt of a start signal (pushbutton S1) the TMS7 closes the forward run contactor (K1M) and controls the motor according to the programmed Primary Motor Settings. On receipt of a stop signal (pushbutton S2) the TMS7 opens the forward run contactor (K1M) and closes the braking contactor (K2M) after a delay of approximately 2-3 seconds (K1T). K3A is also closed to activate the Secondary Motor Settings which should be user programmed for the desired stopping performance characteristics. When motor speed approaches zero the shaft rotation sensor (A2) stops the soft starter and opens the braking contactor (K2M). Function Settings: - Function 23. Relay Output C Functionality = 0 (Assigns the Trip function to Relay Output C) - Functions 1~9 (Sets starting performance characteristics) - Functions 80~88 (Sets braking performance characteristics) TMS7 SERIES ME00070B 27 APPLICATION EXAMPLES 8.4 Two Speed Motors K3M SEE NOT E1. T4 T5 T6 K2M L1 L1B L2 L2B L3 L3B 3 PHASE SUPPLY T1 T1 TO DUAL SPEED MOTOR DAHLANDER T YPE T2 T2 T3 T3 K1M E A1 CONTROL SUPPLY K1A A2 SUPPLY A3 I44 C1 I43 FLC SELECT THERM. C2 MOT OR THERM ISTOR I34 K1M K2M I33 START I22 I21 STO P S1 I12 K3M K1M I11 RESET R11 OUT PUT C K2A K2M K1A K3M K3M R14 R12 K1M K2M CONTROL SUPPLY K2A REM OTE LOW SPEED START INPUT LEGEND K1A K1A REMOTE HIGH SPEED START INPUT K2A K1A K2A K1M K2M K3M S1 REM OTE START RELAY (LOW SPEED) REMO TE START RELAY (HIGH SPEED) LINE CONTACTOR (HIGH SPEED) LINE CONTACT OR (LO W SPEED) STAR CONTACT OR (HIGH SPEED) RESET PUSHBUTT ON 1. NOTES CONTACTORS K2M AND K3M MUST BE MECHANICALLY INTERLOCKED. Description: The TMS7 can be configured for control of dual speed Dahlander type motors. In this application the TMS7 is employed with a High Speed contactor (K1M), Low Speed contactor (K2M) and a Star contactor (K3M). On receipt of a High Speed start signal the High Speed contactor (K1M) and Star contactor (K3M) are closed. The TMS7 then controls the motor according to the Primary Motor Parameter set. (Function Numbers 1~9) On receipt of a Low Speed start signal the Low Speed contactor (K2M) is closed. The relay contact across Input A is also closed causing the TMS7 to control the motor according to the Secondary Parameter set (Function Numbers 80~88). Function Settings: - Function 23. Relay Output C Functionality = 0 (Assigns the Trip function to Relay Output C) 28 ME00070B TMS7 SERIES TROUBLE SHOOTING Section 9 Code Trouble Shooting 9.1 Trip Codes When the TMS7 enters the trip state the cause of the trip is indicated on the LED display panel. Code Description 0 Shorted SCR The TMS7 has detected a shorted SCR(s). 1. Determine the affected phase using the 3 phase indicators LEDs located on the left hand side of the TMS7 cover. Damaged SCRs are indicated by an extinguished phase indicator LED (all phase indicator LEDs should be illuminated when input voltage is present but the motor is not running). SCR damage can be verified using the Power Circuit Test described in the Test & Measurement chapter of this section. 2. Replace the damaged SCR. Overcurrent trip The motor has been overloaded and the motor’s thermal limit, as calculated by the TMS7 motor thermal model, has been reached. 1. Remove the cause of the overload and let the motor cool before restarting. 3 Motor thermistor trip The motor thermistors have indicated an overtemperature situation. 1. Identify and correct the cause of the motor overheating. 2. If no thermistors are connected to the TMS7, ensure there is a closed circuit across the motor thermistor input (terminals C1 & C2). 4 5 Current imbalance trip An imbalance in the phase currents has exceeded the limits set in Function 7. Current Imbalance Sensitivity. 1. Monitor the supply voltage 2. Check the motor circuit Supply frequency trip Supply frequency has varied outside the TMS7’s specified range. 1. Correct the cause of the frequency variations. 2. Check the three phase supply to the TMS7. Loss of all three phases is seen by the TMS7 as a 0Hz situation and may be the cause of a supply frequency trip. 3. Check the three phase supply to the TMS7 is connected to input terminals L1, L2, L3. Incorrect connection of the incoming supply to the output terminals T1, T2, T3 means there is no supply connected to the TMS7 input. This will be seen as TMS7 SERIES 6 Phase rotation trip The TMS7 has detected a phase rotation that has been prohibited by the setting made in Function 30. Phase Rotation Protection. 1. Change the incoming phase rotation. 7 Stall trip The TMS7 has measured a current equal to the limit set in Function 9. Stall Protection. 1. Identify and correct the cause of the instantaneous overload event. 8 Power circuit fault The TMS7 has detected a fault in the power circuit. 1. Ensure that the motor is correctly connected to the TMS7 and verify the circuit. 2. Check that voltage is correctly applied to all three TMS7 input terminals (L1, L2 & L3). 3. Reset the trip condition by removing and reapplying control voltage to the TMS7. 2 Description connected to the TMS7 input. This will be seen as a 0Hz situation and may the cause of a supply frequency trip. 9 Undercurrent trip The TMS7 has measured a run current lower than the limit set in Function 8. Undercurrent Protection. 1. Identify and correct the cause of the undercurrent event. F Heatsink overtemperature trip The TMS7 heatsink temperature sensor has indicated and excess heatsink temperature. 1. Verify that the TMS7 has sufficient ventilation. 2. Verify that cooling air is able to freely circulate through the TMS7. 3. Verify that the TMS7 cooling fans (if fitted) are working. P Invalid motor connection The TMS7 cannot detect a valid motor circuit. 1. Ensure the motor is connected to the TMS7 in a valid configuration. Refer to Section 5 Power Circuits for further detail. C RS485 communication fault The RS485 link connected to the TMS7 has been inactive for a period of time greater than set in Function 60. RS485 – Timeout Protection. 1. Restore the RS485 link. E EEPROM read/write failure The TMS7 has failed to read or write to the internal EEPROM. Reset the TMS7. If the problem persists contact your supplier. Out of range FLC The TMS7 has detected that the motor is connected in the 3 Wire configuration and that Function 1. Motor FLC or Function 80 Motor FLC (secondary motor settings) has been set in excess of the TMS7’s maximum capability for this connection format. 1. Reduce the motor FLC setting and then reset the TMS7. Note that the TMS7 cannot be reset until the FLC setting has been corrected. 2. Alternatively, remove control voltage from the TMS7 and reconnect the motor in 6 Wire. ME00070B 29 TROUBLE SHOOTING Code 9.3 General Faults Description TMS7 and reconnect the motor in 6 Wire. Symptom Incorrect main control module. The TMS7 is fitted with an incompatible main control module. 1. Fit a suitable main control module. u Uncontrolled start. Power factor correction capacitors connected to the TMS7 output. Remove any power factor correction from the output of the soft starter. Connection of power factor correction capacitors to the output of a soft starter can result in damage to the SCRs so they should be checked by using the SCR test described in section 9.4 Tests and Measurements. CPU error Reset the TMS7. If the problem persists contact your supplier. 9.2 Fault History Damaged SCRS. Verify soft starter operation using the SCR test described in section 9.4 Tests and Measurements. The TMS7 includes a Fault History Log that records the last eight trip events. Each trip is numbered. Trip number 1 is the most recent trip with trip number 4 being the oldest. 1-4 Trip Code Trip Number Cause Damaged firing circuit. Verify the TMS7 SCR firing circuit using the Power Circuit Test described in section 9.4 Tests and Measurements. 1 = Most recent trip 2 = Previous trip TMS7 will not operate. . . . 4 = Oldest trip Local push buttons not active. The TMS7 may be in remote control mode. (Refer to Function 20. Local/Remote Operation) Remote control inputs not active. The TMS7 may be in local control mode. (Refer to Function 20. Local/Remote Operation) The Fault History can be viewed by selecting Function 101. Fault History and using the <UP> and <DOWN> keys to scroll through the Fault History. Faulty start signal. Verify any circuits connected to the TMS7 remote control inputs. The state of the remote circuits is indicated by the TMS7 remote control input LEDs. The LEDs are illuminated when there is a closed circuit. For there to be a successful start there must be a closed circuit across the start, stop and reset circuits. NOTE: The TMS7 records trips in the Fault History log immediately after they are detected, this requires CAUTION control voltage to be present after the trip. Trips caused by or involving a loss of control voltage may not be recorded. A ‘marker’ can be inserted into the Fault History log to identify trips that have occurred after placement of the ‘marker’. To insert a ‘marker’ enter the programming mode and move to Function 101. Fault History. Then simultaneously depress the <UP> and <DOWN> and <STORE> keys. The marker is added as the most recent fault and is displayed as three horizontal lines as shown below. No, or incorrect control voltage. Ensure the correct control voltage is applied to the inputs A1, A2, A3. Restart delay active. The TMS7 cannot be started during the restart delay period. The period of the restart delay is set using Function 31. Restart Delay. Auto-reset function active. If there has been a trip and the auto-reset function is active the fault must be manually reset before a manual restart can be attempted. (Refer to Functions 70, 71, 72 & 73 ) NOTE: Trip makers must be separated by at least one trip and cannot be placed consecutively. TMS7 in programming mode. The TMS7 will not run while in programming mode. CAUTION The motor will not accelerate to full speed. Start current too low. Check the load is not jammed. Increase start current using Function 2. Current Limit. Function setting Incorrect programming procedure. cannot be made or Function settings must be stored using the are not recorded. <STORE> button. Refer to section 7.1 Programming Procedure for further detail. Function settings are locked. Ensure that Function 112. Function Lock is set for Read/Write. 30 ME00070B TMS7 SERIES TROUBLE SHOOTING Symptom Erratic motor operation and tripping. Test Cause SCRs not latching. SCRs require a minimum current flow to ‘latch’ on. In situations where very small motors are being controlled by large soft starters the current drawn may be insufficient to latch on the SCRs. Increase motor size or reduce soft start size. Soft stop ends before the programmed ramp time. Motor will not stall. The TMS7 has significantly reduced the voltage applied to the motor without detecting a reduction in motor speed. This indicates that with present motor loading further control of the voltage will be ineffectual, hence the soft stop function has halted. TMS7 display shows a ‘h’ The START button on the local control panel is stuck. Release the button to restore normal operation. TMS7 will not enter The TMS7 is running. The TMS7 must be the programming stopped before programming mode can be mode. accessed. No, or incorrect control voltage. Ensure the correct control voltage is applied to the inputs A1, A2, A3. Procedure 2. Remove the motor cables from the output terminals of the TMS7 (T1, T2 & T3). 3. Use a 500 VDC insulation tester to measure the resistance between the input and output of each phase of the TMS7 (L1-T1, L2-T2, L3-T3). Note that low voltage ohm meters or multimeters are not adequate for this measurement. 4. The measured resistance should be close to 33kΩ and approximately equal on all three phases. 5. If a resistance of less than about 10kΩ is measured across the SCR, the SCR should be replaced. 6. If a resistance greater than about 60kΩ is measured across the SCR there could be a fault with the TMS7 control module or firing loom. 9.4 Tests & Measurements Test Run performance test. Procedure This test verifies correct operation of the TMS7 during run. 1. Control input test Measure the voltage drop across each phase of the TMS7 (L1–T1, L2–T2, L3–T3). The voltage drop will be less than approximately 2 VAC when the TMS7 is operating correctly. This test verifies circuits connected to the TMS7 remote control inputs. (Start, Stop, Reset & FLC Select) 1. Measure the voltage across each input. With the remote circuit closed there should be 0VDC measured. If 24VDC is measured the switch/control is incorrectly connected or faulty. Start performance This test verifies correct operation of the test. TMS7 during start. Power circuit test. 1. Determine the expected start current by multiplying the settings made in Function 1. Motor Full Load Current and Function 2. Current Limit. 2. Start the motor and measure the actual start current. 3. If the expected start current and the actual start current are the same, the TMS7 is performing correctly. This test verifies the TMS7 power circuit including the SCR, firing loom and control module. 1. TMS7 SERIES Remove the incoming supply from the TMS7 (L1, L2, L3 and control supply). ME00070B 31 APPENDIX Appendix 10.1 The above table is intended as a guide only. Individual machine and motor characteristics will determine the actual start current requirements. Typical Start Current Requirements 10.2 Compressor - Screw (loaded) — Compressor - Screw (unloaded) — Conveyor - Belt — Conveyor - Roller — Conveyor - Screw — Crusher - Cone — Crusher - Jaw — — — Crusher - Rotary Crusher - Vertical Impact Debarker — Dryer — — — Dust Collector Edger Fan - Axial (Damped) 10.3 — Fan - Axial (Un-damped) — Fan - Centrifugal (Damped) Fan - High Pressure 90 A: AC-53b 3.5-15 : 345 — — Grinder Hydraulic Power Pack Off Time (seconds) Start Time (seconds) Start Current (multiple of FLC) Starter Current Rating (Amps) — — — — — — Mill Mill - Ball Mill - Hammer Mill - Roller Mixer Palletiser Starter Current Rating: The Full Load Current rating of soft starter given the parameters detailed in the remaining sections of the utilisation code. Start Current: The maximum available start current given the parameters detailed in the remaining sections of the utilisation code. Start Time: The maximum available start time given the parameters detailed in the remaining sections of the utilisation code. Off Time: The minimum allowable time between end of one start and the beginning of the next start given the parameters detailed in the remaining sections of the utilisation code. — — Planer Press — — Pump - Centrifugal Pump - Positive Displacement — — — Pump - Slurry Re-pulper AC53b Utilisation Codes AC53b Utilisation Category Format — — Fan - Centrifugal (Un-damped) — — Rotary Table Sander — Saw - Bandsaw — Saw - Circular — — Separator Shredder 32 Starter Current Rating: The Full Load Current rating of soft starter given the parameters detailed in the remaining sections of the utilisation code. Start Current: The maximum available start current given the parameters detailed in the remaining sections of the utilisation code. Start Time: The maximum available start time given the parameters detailed in the remaining sections of the utilisation code. On-load Duty Cycle: The maximum permissible percentage of each operating cycle that the soft starter can operate given the parameters detailed in the remaining sections of the utilisation code. Starts Per Hour: The maximum available number of starts per hour given the parameters detailed in the remaining sections of the utilisation code. — — Compressor - Recip (unloaded) Slicer Starts Per Hour On-load Duty Cycle (% ) Start Time (seconds) Start Current (multiple of FLC) Starter Current Rating (Amps) — — — Chipper Compressor - Recip (loaded) Tumbler 78 A: AC-53a 3.5-15 : 50-10 — Centrifuge Pump - Bore 450% 400% 350% 300% Atomiser Bottle Washer AC53a Utilisation Category Format — — Agitator AC53a Utilisation Codes — — ME00070B TMS7 SERIES
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
Download PDF
advertisement