TOSHIBA MK5002MAL hard drive User manual

TOSHIBA AMERICA INFORMATION SYSTEMS

STORAGE DEVICE DIVISION

IRVINE, CALIFORNIA

MK5002MAL (HDD1242)

1.8-INCH HARD DISK DRIVE

USER MANUAL

Rev 02

11/2006

CONTENTS

Introduction..............................................................................1

Setup ........................................................................................2

Using the HDD .........................................................................3

Specifications ..........................................................................4

Drive Connectors.....................................................................6

INTRODUCTION – MK5002MAL (HDD1242)

General Features

• 1.8" sized drive

• 1 Platter

• 5.007 Gigabytes*

• 5mm High

• 15ms Average Seek Time

• ATA (1 - 5) Interface

• Ultra 66 DMA Suppoted

• 1024KB Buffer

• Rotational speed of 4,200rpm

• MTTF 300,000 Hours

*Toshiba defines a megabyte (MB) as 1,000,000 bytes and a gigabyte (GB) as 1,000,000,000 bytes.

1

SETUP – MK5002MAL (HDD1242)

Caution: Your Hard Disk Drive is a precision device and even a small drop onto any surface can cause damage. Electronstatic discharge can also damage the drive. You should ground yourself prior to handling the drive.

Figure 1. MK5002MAL Side View

Installation Notes

• Do not apply any force to the top cover, except the screw areas on top cover. Maximum force to the specified area is 2N. important Note: Disconnect power from your computer system before beginning

installation

2

USING THE HARD DISK DRIVE – MK5002MAL (HDD1242)

Backing up Data Files

To avoid data loss, regularly back up the data files on the hard disk drive.

3

SPECIFICATIONS –MK5002MAL (HDD1242)

General

Interface ATA-1/2/3/4/5

Functionality

Formatted Capacity

Rotational Speed

Avg. Rotational Latency

5.007GB*

4200rpm

7.14/ms

Spin-up Time 3.5sec (typical)

Buffer 1024KB

Seek Time

Average

Maximum

15

26

Internal Transfer Rate

Host Transfer Rate

118 ~ 175.3 Mbits/sec (max)

66.7Mbytes/sec

Interleave Factor

16.6Mbytes/sec

1:1

*Toshiba defines a megabyte (MB) as 1,000,000 bytes and a gigabyte (GB) as 1,000,000,000 bytes.

Internal Drive Characteristics

Number of Disks

Number of Data Heads

Track Density (TPI)

Logical Cylinders

Logical Heads

Logical Sectors/track

Bytes per Sector

Logical Blocks (LBA)

Reliability

Preventative maintenance

Non-recoverable read errors

Electrical

1

2

1638 (41.6k)

10,350

16

63

512

9,780,750

None

1 error per 10

13

bits read

Power Consumption

Energy Consumption Efficiency

4

0.10W/GB avg

Shock

Operating

Non-Operating

Physical

1,960m/s

9,800m/s

2

2

(200G)(2msec)

(1000G)(1msec)

Regulatory

The drive satisfies the following standards:

Underwriters Laboratories (UL) 1950

Canadian Standard Association (CSA) C22.2 No. 950

TUV Rheinland

EMC - EN50081-1

EMC - EN50082-1

EN 60 950

EN50081-1: 1992

EN55022: 1994 Class B

EN61000-3-2: 1995

EN61000-3-3: 1995

EN61000-4-2: 1995

EN61000-4-3: 1998

ENV50204: 1995

EN61000-4-4: 1995

EN61000-4-5: 1995

EN61000-4-6: 1996

EN61000-4-11: 1994

5

DRIVE CONNECTORS –MK5002MAL (HDD1242)

Figure 1. MK5002MAL HDD - INTERFACE CONNECTOR

Interface Connector

Drive Side Connector

Recommended Host Side Connector

MCD-D50 Series by DDK Connectors

MCD-D50 Series by DDK Connectors

6

Interface Signals

1

3

5

DRIVE INTERFACE SIGNALS

RESET

DD 7

DD 6

2

4

6

GROUND

DD 8

DD 9

7

19 GROUND 20 OPEN

23 DIOW/STOP 24 GROUND

25 DIOR/ 26 GROUND

-DMARDY

HSTROBE

27 IORDY/ 28 CSEL

-DMARDY/-

DSTROBE

31 INTRQ 32 IOCS16

41 3.3V (LOGIC) 42 3.3V (MOTOR)

Note: Symbol () in front of signal indicates negative logic.