Toshiba SD-V390-S-TU Speaker System User Manual

Toshiba SD-V390-S-TU Speaker System User Manual
DVD VIDEO PLAYER &
VIDEO CASETTE RECORDER
SD-V390-S-TU
OWNER’S MANUAL
Before connecting, operating or adjusting this product,
please read this instruction booklet carefully and completely.
©2002 Toshiba Corporation
This device does not tape-record copy protected DVD Video Discs.
1-49
Safety Precautions
CAUTION: The apparatus should not be exposed to water
(dripping or splashing) and no objects filled with liquids, such
as vases, should be placed on the apparatus.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
FCC WARNING: This equipment may generate or use radio
frequency energy. Changes or modifications to this
equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The
user could lose the authority to operate this equipment if an
unauthorized change or modification is made.
CAUTION: TO REDUCE THE RISK
OF ELECTRIC SHOCK
DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
This lightning flash with arrowhead symbol within an
equilateral triangle is intended to alert the user to
the presence of uninsulated dangerous voltage
within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of electric
shock to persons.
The exclamation point within an equilateral triangle
is intended to alert the user to the presence of
important operating and maintenance (servicing)
instructions in the literature accompanying the
product.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO
RAIN OR MOISTURE.
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH
WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
ATTENTION: POUR ÉVITER LES CHOC ÉLECTRIQUES,
INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE
DANS LA BORNE CORRESPONDANTE DE LA PRISE ET
POUSSER JUSQU’AU FOND.
WARNING: Do not install this equipment in a confined space
such as a book case or similar unit.
NOTE TO CABLE/TV INSTALLER: This reminder is provided to
call the cable TV system installer’s attention to Article 820-40 of
the National Electric Code (U.S.A.). The code provides guidelines
for proper grounding and, in particular, specifies that the cable
ground shall be connected to the grounding system of the
building, as close to the point of the cable entry as practical.
CAUTION:
This DVD+VCR employs a Laser System.
To ensure proper use of this product, please read this owner’s
manual carefully and retain for future reference should the unit
require maintenance, contact an authorized service location.
Use of controls, adjustments, or the performance of procedures other than those specified herein may result in hazardous radiation exposure.
To prevent direct exposure to laser beam, do not try to open
the enclosure. Visible laser radiation when open. DO NOT
STARE INTO BEAM.
REGULATORY INFORMATION: FCC Part 15
This product has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the product is
operated in a residential installation. This product generates,
uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur
in a particular installation. If this product does cause harmful
interference to radio or television reception, which can be
determined by turning the product off and on, the user is
encouraged to try to correct the interference by one or more
of the following measures:
z Reorient or relocate the receiving antenna.
z Increase the separation between the product and
receiver.
z Connect the product into an outlet on a circuit different
from that to which the receiver is connected.
z Consult the dealer or an experienced radio/TV technician
for help.
NOTES ON COPYRIGHTS:
It is forbidden by law to copy, broadcast, show, broadcast
via cable, play in public, or rent copyrighted material without
permission.
This product features the copy protection function developed
by Macrovision. Copy protection signals are recorded on some
discs. When recording and playing the pictures of these discs
on a VCR, picture noise will appear.
This product incorporates copyright protection technology that
is protected by method claims of certain U.S. patents and other
intellectual property rights owned by Macrovision Corporation
and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is
intended for home and other limited viewing uses only unless
otherwise authorized by Macrovision Corporation. Reverse
engineering or disassembly is prohibited.
SERIAL NUMBER: The serial number is found on the back of
this unit. This number is unique to this unit and not available to
others. You should record requested information here and
retain this guide as a permanent record of your purchase.
Model No. ___________________________________
Serial No. ___________________________________
1-50
CAUTION:
PLEASE READ AND OBSERVE ALL WARNINGS AND
INSTRUCTIONS IN THIS OWNER’S MANUAL AND THOSE
MARKED ON THE UNIT. RETAIN THIS BOOKLET FOR
FUTURE REFERENCE.
This set has been designed and manufactured to assure personal safety.
Improper use can result in electric shock or fire hazard. The safeguards
incorporated in this unit will protect you if you observe the following procedures for installation, use, and servicing.
This unit does not contain any parts that can be repaired by the user.
DO NOT REMOVE THE CABINET COVER, OR YOU MAY BE
EXPOSED TO DANGEROUS VOLTAGE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL ONLY.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
Read These Instructions
All safety and operating instructions should be read before the
product is operated.
Follow All Instructions
All operating and use instructions should be followed.
Keep These Instructions
The safety and operating instructions should be retained for future
reference.
Heed All Warnings
All warnings on the product and in the operating instructions should
be adhered to.
Power Sources
This product should be operated only from the type of power
source indicated on the marking label. If you are not sure of the
type of power supply in your home, consult your product dealer or
local power company. For products intended to operate from battery power, or other sources, refer to the operating instructions.
Grounding or Polarization
Do not defeat the safety purpose of the polarized plug has two
blades with one wider than the other. A grounding-type plug has
two blades and a third grounding prong. The wide blade or the
prong are provided for your safety. If the provided plug does not fit
into your outlet, consult an electrician for replacement of the obsolete outlet.
Ventilation
Slots and openings in the cabinet are provided for ventilation and to
ensure reliable operation of the product and to protect it from overheating. These openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa,
rug or other similar surface. This product should not be placed in a
built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered
to.
Heat
Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce
heat.
Water and Moisture
Do not use this apparatus near water. For example: near a bath
tub, wash bowl, kitchen sink, Laundry tub, in a wet basement; or
near a swimming pool.
Cleaning
Unplug this product from the wall outlet before cleaning. Do not use
liquid cleaners or aerosol cleaners. Clean only with dry cloth.
Power-Cord Protection
Protect the power cord from being walked on or pinched particularly
at plugs, convenience receptacles, and the point where they exit
from the apparatus.
Overloading
Do not overload wall outlets, extension cords, or integral convenience receptacles, this can result in a risk of fire or electric shock.
Lightning
Unplug this apparatus apparatus during lightning storms or when
unused for long periods of time. This will prevent damage to the
product due to lightning and power-line surges.
Object and Liquid Entry
Never push objects of any kind into this product through openings
as they may touch dangerous voltage points or short-out parts that
could result in a fire or electric shock. Never spill liquid of any kind
on the product.
15. Attachments
Only use attachments/accessories specified by the manufacturer.
16. Accessories
Use only with the cart, stand, tripod, bracket, or
table specified by the manufacturer or sold with
the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination to
PORTABLE CART
avoid injury from tip-over.
WARNING
17. Disc Tray
Keep your fingers well clear of the disc tray as it is closing. It can
cause personal injury.
18. Burden
Do not place a heavy object on or step on the product. The object
may fall, causing serious personal injury and serious damage to the
product.
19. Connecting
When you connect the product to other equipment, turn off the
power and unplug all of the equipment from the wall outlet. Failure
to do so may cause an electric shock and serious personal injury.
Read the owner’s manual of the other equipment carefully and follow the instructions when making any connections.
20. Sound Volume
Reduce the volume to the minimum level before you turn on the
product. Otherwise, sudden high volume sound may cause hearing
or speaker damage.
21. Sound Distortion
Do not allow the product to output distorted sound for a longtime. It
may cause speaker overheating and fire.
22. Earphone
When you use the earphone, keep the volume at a moderate level.
If you use the earphone continuously with high volume sound, it
may cause hearing damage.
23. Laser Beam
Do not look into the opening of the disc tray or ventilation opening
of the product to see the source of the laser beam. It may cause
sight damage.
24. Disc
Do not use a cracked, deformed, or repaired disc. These discs are
easily broken and may cause serious personal injury and product
malfunction.
25. Damage Requiring Service
Refer all servicing to qualified service personnel. Servicing is
required when the apparatus has been damaged in any way, such
as power-supply cord or plug is damaged, liquid has been spilled or
objects have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normal, or has been
dropped.
26. Servicing
Do not attempt to service this product yourself as opening or
removing the cover may expose you to dangerous voltage or other
hazards. Refer all servicing to qualified service personnel.
27. Replacement parts
When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or
have the same characteristics as the original part. Unauthorized
substitutions may result in fire, electric shock, or other hazards.
28. Safety Check
Upon completion of any service or repairs to this product, ask the
service technician to perform safety checks to determine that the
product is in proper operating condition.
1-51
INTRODUCTION
IMPORTANT SAFETY INSTRUCTIONS
Table of Contents
Introduction
Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . 2
IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . 3
Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Before Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6
Playable Discs . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Notes on Discs . . . . . . . . . . . . . . . . . . . . . . . . . . 6
About Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Display Window. . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Preparation
Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-14
Connecting Antenna/Cable TV to a DVD+VCR . . 11
Basic TV Connections . . . . . . . . . . . . . . . . . . . . 12
Optional, Preferred TV Connections . . . . . . . 13-14
Before Operation - VCR Part . . . . . . . . . . . . . . 15-17
On-Screen Display(OSD) . . . . . . . . . . . . . . . . . . 15
Setting the On-Screen Display . . . . . . . . . . . . . . 15
Setting the VCR Setup Menu . . . . . . . . . . . . . . . 16
Channel Selection . . . . . . . . . . . . . . . . . . . . . . . 16
Setting the Clock . . . . . . . . . . . . . . . . . . . . . . . . 17
Before Operation - DVD Part . . . . . . . . . . . . . . 18-21
General Explanation. . . . . . . . . . . . . . . . . . . . . . 18
On-Screen Display . . . . . . . . . . . . . . . . . . . . . . . 18
Initial Settings . . . . . . . . . . . . . . . . . . . . . . . . 19-22
z General Operation . . . . . . . . . . . . . . . . . . . . 19
z Language . . . . . . . . . . . . . . . . . . . . . . . . . . 19
z Picture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
z Sound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
z Others . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
z Parental Control . . . . . . . . . . . . . . . . . . . . . . 21
Operation
Operation with tape . . . . . . . . . . . . . . . . . . . . . 22-28
Normal Playback . . . . . . . . . . . . . . . . . . . . . . . . 22
Special Effect Playbacks . . . . . . . . . . . . . . . . . . 22
z Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
z Still Picture and Frame-by-Frame Playback . 22
z Slow Motion . . . . . . . . . . . . . . . . . . . . . . . . . 22
z Instant Skip . . . . . . . . . . . . . . . . . . . . . . . . . 22
VISS (VHS Index Search System) . . . . . . . . . . . 23
Normal Recording . . . . . . . . . . . . . . . . . . . . . . . 23
Timer Recording . . . . . . . . . . . . . . . . . . . . . . 24-25
One touch Timer Recording(OTR) . . . . . . . . . . . 25
Dubbing and Editing. . . . . . . . . . . . . . . . . . . . . . 26
Copying from DVD to VCR. . . . . . . . . . . . . . . . . 26
VHS Hi-Fi Stereo System/MTS Broadcast . . . . . 27
Tape Counter Memory Feature. . . . . . . . . . . . . . 28
Additional Information . . . . . . . . . . . . . . . . . . . . 28
z S-VHS Quasi Playback (SQPB) . . . . . . . . . . 28
z Auto Play System. . . . . . . . . . . . . . . . . . . . . 28
z Video Head Cleaning . . . . . . . . . . . . . . . . . . 28
z Blank Search . . . . . . . . . . . . . . . . . . . . . . . . 28
Operation with DVD and Video CD . . . . . . . . . 29-32
Playing DVD and Video CD . . . . . . . . . . . . . . . . 29
General Features . . . . . . . . . . . . . . . . . . . . . . . . 29
z Moving to another TITLE . . . . . . . . . . . . . . . 29
z Moving to another CHAPTER. . . . . . . . . . . . 29
z Slow Motion . . . . . . . . . . . . . . . . . . . . . . . . . 29
z Still Picture and Frame-by-Frame Playback . 30
z Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
z Random. . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Time Search . . . . . . . . . . . . . . . . . . . . . . .
Selecting the sound enhancement . . . . . . .
z Repeat. . . . . . . . . . . . . . . . . . . . . . . . . . . .
z Repeat A-B . . . . . . . . . . . . . . . . . . . . . . . .
z Zoom . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
z Marker Search . . . . . . . . . . . . . . . . . . . . . .
Special DVD Features . . . . . . . . . . . . . . . . . . .
z Checking the contents of DVD Video discs: Menus
z Title Menu . . . . . . . . . . . . . . . . . . . . . . . . .
z Disc Menu . . . . . . . . . . . . . . . . . . . . . . . . .
z Camera Angle . . . . . . . . . . . . . . . . . . . . . .
z Changing the Audio Language . . . . . . . . . .
z Changing the Audio Channel . . . . . . . . . . .
z Subtitle . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operation with Audio CD . . . . . . . . . . . . . . . . . .
Playing an Audio CD . . . . . . . . . . . . . . . . . . . .
z Pause . . . . . . . . . . . . . . . . . . . . . . . . . . . .
z Moving to another Track . . . . . . . . . . . . . .
z Repeat Track/ All/ Off. . . . . . . . . . . . . . . . .
z Search. . . . . . . . . . . . . . . . . . . . . . . . . . . .
z Random . . . . . . . . . . . . . . . . . . . . . . . . . .
z Repeat A-B . . . . . . . . . . . . . . . . . . . . . . . .
z Selecting the sound enhancement . . . . . . .
z Changing the Audio Channel . . . . . . . . . . .
Operation with MP3 Disc. . . . . . . . . . . . . . . . . . .
Playing an MP3 disc . . . . . . . . . . . . . . . . . . . .
z Pause . . . . . . . . . . . . . . . . . . . . . . . . . . . .
z Moving to another Track . . . . . . . . . . . . . .
z Repeat Track/ All/ Off. . . . . . . . . . . . . . . . .
Notes on MP3 Discs . . . . . . . . . . . . . . . . . . . .
Operation with JPEG Disc. . . . . . . . . . . . . . . . . .
Viewing a JPEG disc . . . . . . . . . . . . . . . . . . . .
z Moving to another File . . . . . . . . . . . . . . . .
z Repeat All/ Off . . . . . . . . . . . . . . . . . . . . . .
Operation with WMA Disc . . . . . . . . . . . . . . . . . .
Playing an WMA disc . . . . . . . . . . . . . . . . . . . .
z Pause . . . . . . . . . . . . . . . . . . . . . . . . . . . .
z Moving to another Track . . . . . . . . . . . . . .
z Repeat Track/ All/ Off. . . . . . . . . . . . . . . . .
Programmed Playback . . . . . . . . . . . . . . . . . . . .
Programmed Playback with Audio CD, MP3
JPEG and WMA Discs . . . . . . . . . . . . . . . . . . .
Programmed Playback with Video CD . . . . . . .
z Repeat Programmed Tracks/All/Off . . . . . .
z Repeat Programmed All/Off . . . . . . . . . . . .
z Erasing a Track/File from Program List. . . .
z Erasing the Complete Program List . . . . . .
Additional Information - DVD Part . . . . . . . . . . .
One Touch Replay . . . . . . . . . . . . . . . . . . . . . .
Screen Saver . . . . . . . . . . . . . . . . . . . . . . . . . .
Video Mode Setting . . . . . . . . . . . . . . . . . . . . .
z
z
. 30
. 30
. 31
. 31
. 31
. 31
. 32
. 32
. 32
. 32
. 32
. 32
. 32
. 32
. 33
. 33
. 33
. 33
. 33
. 33
. 33
. 33
. 33
. 33
. 34
. 34
. 34
. 34
. 34
. 34
. 35
. 35
. 35
. 35
. 36
. 36
. 36
. 36
. 36
. 37
.
.
.
.
.
.
.
.
.
.
37
37
38
38
38
38
39
39
39
39
Reference
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . 40-41
Language Code List . . . . . . . . . . . . . . . . . . . . . . . 42
Country/Area Code List. . . . . . . . . . . . . . . . . . . . . 43
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45-46
About the symbols for instructions
Indicates hazards likely to cause harm to the unit
itself or other material damage.
Indicates special operating features of this unit.
Indicates tips and hints for making the task easier.
1-52
Before Use
Title (DVD only)
The main film content or accompanying feature content
or music album.
Each title is assigned a title reference number enabling
you to locate it easily.
Video CD (VCD)
(8 cm / 12 cm disc)
Audio CD
(8 cm/12 cm disc)
In addition, this unit can play a DVD-R, CD-R or
CD-RW that contains audio titles, MP3 or JPEG files.
Notes
– Depending on the conditions of the recording equipment or the CD-R/RW disc itself, some CD-R/RW
discs cannot be played on the unit.
– The unit cannot play discs that contain data other
than MP3 and CD-DA data.
– Do not attach any seal or label to either side (the
labeled side or the recorded side) of a disc.
– Do not use irregularly shaped CDs (e.g., heartshaped or octagonal). It may result in malfunctions.
Notes on DVDs and Video CDs
Some playback operations of DVDs and Video CDs
may be intentionally fixed by software manufacturers.
As this unit plays DVDs and Video CDs according to
disc content designed by the software manufacturer,
some playback features of the unit may not be available, or other functions may be added.
Refer also to the instructions supplied with the DVDs
and Video CDs. Some DVDs made for business purposes may not be playable on this unit.
Regional code of the DVD+VCR and DVDs
This DVD+VCR is designed and manufactured
for playback of region 1 encoded DVD software.
The region code on the labels of some DVD
discs indicates which type of DVD+VCR can
play those discs. This unit can play only DVD discs
labeled 1 or ALL. If you try to play any other discs, the
message “Check Regional Code” will appear on the TV
screen. Some DVD discs may not have a region code
label even though their playback is prohibited by area
limits.
1
Note on DTS-encoded CDs
When playing DTS-encoded CDs, excessive noise may
be exhibited from the analog stereo output. To avoid
possible damage to the audio system, turn down the
volume before playing back such discs, adjust the volume gradually, and keep the volume level low. To enjoy
DTS Digital SurroundTM playback, an external 5.1 channel DTS Digital SurroundTM decoder system must be
connected to the digital output of the unit.
Chapter (DVD only)
Sections of a picture or a musical piece that are smaller
than titles. A title is composed of one or several chapters. Each chapter is assigned a chapter number to
enable you to locate the chapter you want. Depending
on the disc, chapters may not be recorded.
Track (Video CD and audio CD only)
Sections of a picture or a musical piece on a video CD
or an audio CD. Each track is assigned a track number,
enabling you to locate the track you want.
Scene
On a video CD with PBC (Playback control) functions,
moving pictures and still pictures are divided into sections called “Scenes”. Each scene is displayed in the
menu screen and assigned a scene number, enabling
you to locate the scene you want.
A scene is composed of one or several tracks.
Types of video CDs
There are two types of video CDs:
Video CDs equipped with PBC (Version 2.0)
PBC (Playback control) functions allow you to interact
with the system via menus, search functions, or other
typical computer-like operations. Moreover, still pictures
of high resolution can be played if they are included in
the disc.
Video CDs not equipped with PBC (Version 1.1)
Operated in the same way as audio CDs, these discs
allow playback of video pictures as well as sound, but
they are not equipped with PBC.
Remote control battery installation
AAA
AAA
DVD
(8 cm/12 cm disc)
Detach the battery cover on the rear of the
remote control, and insert two R03 (size
AAA) batteries with
and
aligned
correctly.
Caution
Do not mix old and new batteries. Never mix different
types of batteries (standard, alkaline, etc.).
Remote Control Operation Range
Point the remote control at the remote sensor and press
the buttons.
z Distance: About 23 ft (7 m) from the front of the
remote sensor
z Angle: About 30° in each direction of the front of the
remote sensor
1-53
INTRODUCTION
Disc-related terms
Playable Discs
Before Use (Continued)
Precautions
Handling the unit
When shipping the unit
The original shipping carton and packing materials
come in handy. For maximum protection, re-pack the
unit as it was originally packaged at the factory.
Cleaning discs
Fingerprints and dust on the disc can cause poor picture quality and sound distortion. Before playing, clean
the disc with a clean cloth. Wipe the disc from the center out.
When setting up the unit
The picture and sound of a nearby TV, VCR, or radio
may be distorted during playback. In this case, position
the unit away from the TV, VCR, or radio, or turn off the
unit after removing the disc.
To keep the surface clean
Do not use volatile liquids, such as insecticide spray,
near the unit. Do not leave rubber or plastic products in
contact with the unit for a long period of time. They will
leave marks on the surface.
Cleaning the unit
To clean the cabinet
Use a soft, dry cloth. If the surfaces are extremely dirty,
use a soft cloth lightly moistened with a mild detergent
solution. Do not use strong solvents such as alcohol,
benzine, or thinner, as these might damage the surface
of the unit.
To obtain a clear picture
The DVD+VCR is a high-tech, precision device. If the
optical pick-up lens and disc drive parts are dirty or
worn, the picture quality will be poor.
Regular inspection and maintenance are recommended
after every 1,000 hours of use. (This depends on the
operating environment.)
For details, please contact your nearest dealer.
No
Yes
Do not use strong solvents such as alcohol, benzine,
thinner, commercially available cleaners, or anti-static
spray intended for older vinyl records.
About Symbols
About the
symbol display
“
” may appear on the TV screen during operation.
This icon means the function explained in this owner’s
manual is not available on that specific DVD video disc.
About the disc symbols for instructions
A section whose title has one of the following symbols are
applicable only to those discs represented by the symbol.
DVD DVD
VCD2.0 Video CDs with the PBC (playback control)
function.
VCD1.1 Video CDs without the PBC (playback control)
function.
CD
Audio CDs.
MP3 MP3 Discs.
Notes on Discs
Setting the Output Source
Handling discs
You must select one of your output sources (DVD or
VCR) to view on the TV screen.
Do not touch the playback side of the disc.
Hold the disc by the edges so that fingerprints will not
get on the surface.
Do not stick paper or tape on the disc.
• If you want to view output source of DVD deck:
Press DVD on the remote or DVD/VCR on the front panel
until DVD indicator in the display window lights and output
source of DVD deck is viewed on the TV screen.
• If you want to view output source of VCR deck:
Press VCR on the remote or DVD/VCR on the front panel
until VCR indicator in the display window lights and output
source of VCR deck is viewed on the TV screen.
Storing discs
After playing, store the disc in its case.
Do not expose the disc to direct sunlight or sources of
heat, or leave it in a parked car exposed to direct sunlight, as there may be a considerable temperature
increase inside the car.
NOTES
• If you insert a disc when the DVD+VCR is in the VCR
mode, the DVD+VCR will be set to DVD mode
automatically.
• If you insert a cassette tape without prevention tab
when the DVD+VCR is in the DVD mode, the
DVD+VCR will be set to VCR mode automatically.
1-54
Front Panel
Cassette Compartment (VCR deck)
Insert a video cassette here.
Remote Sensor
Point the DVD+VCR remote control here.
Display window
Shows the current status of the DVD+VCR.
OPEN/CLOSE
Opens or closes the disc tray.
CHANNEL (v/V)
To scan up or
down through
memorized channels.
DVD/VCR indicator
Indicates the active deck.
DVD/VCR SELECT
Toggles control between the
DVD deck and the VCR deck.
LINE 2 (VIDEO IN/AUDIO IN
(Left/Right))
Connect the audio/video output
of an external source (Audio
system, TV/Monitor, Another
VCR).
STOP
Stops playback.
PLAY
To play back a recorded tape.
ON/STANBY
Switches the DVD+VCR ON and OFF.
REW
DVD: Go to beginning of current chapter/track or to previous chapter/track.
Press and hold for a fast reverse search.
VCR: Rewinds the tape during the STOP mode or for fast reverse picture search.
FWD
DVD: Go to NEXT chapter/track. Press and hold for two seconds for a fast forward search.
VCR: Advances the tape during the STOP mode or for fast forward picture search.
REC
To record normally or to activate One-touch Timer Recording
by repeated presses.
1-55
INTRODUCTION
EJECT
Ejects the tape in the VCR deck.
Disc Tray (DVD deck)
Insert a disc here.
Display Window
DVD DVD inserted.
VCD Video CD inserted
CD Audio CD inserted.
A y B Indicates A-B repeat mode.
ALL Indicates repeat all mode.
ANGLE active.
MP3 MP3 disc inserted.
PROG. Programmed playback active.
TITLE Indicates current title number.
CHP/TRK Indicates current chapter or track number.
VCR DVD+VCR functions are available and channels
are selected at DVD+VCR.
TIMER DVD+VCR is in timer recording or a timer
recording is programmed.
REC DVD+VCR is Recording.
CDREC DVD to VCR copy is in
progress.
A
B
PROG. TITLE CHP/TRK VCR TIMER
REC
CDREC HI-FI
AM
SP
LP
EP
ALL MP3
VCD
DVD
ST
SAP CH
CH DVD+VCR is tuned to Channel XX.
SAP Indicates when a SAP BILINGUAL
broadcast is being received.
ST Indicates a stereo broadcast is
being received.
Indicates total playing time, elapsed time, remaining time or
current deck status (Playback, Pause, etc).
HI-FI Indicates the unit is playing back a tape recorded in Hi-Fi.
SP LP EP Displays the recording and playback speed.
AM Indicates AM time. (PM is not displayed.)
A cassette is in the VCR deck.
1-56
Remote Control
DVD/VCR select button
POWER
Select the output source (DVD or VCR)
to view on the TV screen.
Switches DVD+VCR ON and OFF.
0-9 numerical buttons
- Opens and closes the disc tray.
- Ejects the tape in the VCR deck.
Selects numbered options in a menu.
INPUT SELECT
PROGRAM
To select the VCR deck’s source (Tuner,
LINE 1, or LINE 2).
ANGLE
Accesses or removes Program menu.
COUNT RESET, CLEAR
z
- Resets tape counter to M 0:00:00
- Removes a track number on the
program menu or a mark on the
MARKER SEARCH menu.
Selects a DVD camera angle if
available.
SUBTITLE
z
Selects a subtitle language.
AUDIO
CLK/CNT, DISPLAY
z
Accesses On-Screen display.
Switches among the clock, tape counter
and tape remaining modes on the display.
Selects an audio language (DVD) or an
audio channel (CD).
INSTANT REPLAY z
Replays through 10 seconds of
playback.
BLANK SEARCH
Finds end points of recording.
PLAY z
z
Starts playback.
TOP MENU
z
Displays the disc’s Title menu, if
available.
Rewinds the tape during the STOP
mode or for fast reverse picture search.
Accesses menu on a DVD disc.
REW
FWD
z
z
z
Advances the tape during the STOP
mode or for fast forward picture search.
z
Stops playback.
z
z
A-B REPEAT, SP/SLP
- Repeats sequence.
- Selects recording speed
z
z
Skip to beginning of current chapter or track,
press twice in quick successions to go to
previous chapter or track.
Press and hold button for about two seconds
to search backward. (For DVD only)
>
REPEAT
Repeat chapter, track, title, all.
Pause playback or recording
temporarily/press repeatedly for frameby-frame playback.
SKIP
ZOOM
Enlarges DVD video image.
PAUSE/STILL, PAUSE/STEP z
.
RETURN
- Removes the setup menu.
- Displays the menu of a video CD with
PBC.
SLOW z
Forward slow playback of tape.
STOP z
SKIP
MENU
MARKER
Marks any point during playback.
z
VISS, SEARCH
- Enters the VISS function mode.
- Displays MARKER SEARCH menu.
z
z
RANDOM, INSTANT SKIP
- Plays tracks in random order.
- Fast forwards picture search through
30 seconds of recording.
Skip to next chapter or track.
Press and hold button for about two seconds
to search backward.(For DVD only)
z
REC/OTR
Records normally or activates One
touch Timer Recording with repeated
presses.
SETUP, VCR MENU
Accesses or removes DVD setup menu
and VCR menu.
z
TV/VCR
AUTO TRK
Adjusts automatically the tape’s picture
onscreen.
To view channels selected by the VCR
tuner or by the TV tuner.
b/B/v/V (left/right/up/down) z
- Selects an option in the menu
- CH/TRK (+/-): Selects channel of VCR.
Adjusts manually the tape’s picture
onscreen.
ENTER
z
- Acknowledges menu selection.
- Displays functions on the TV screen.
Note
This remote control use the same buttons for VCR and DVD
functions (ex. PLAY).
When using a VCR, first press the VCR button.
When using a DVD, first press the DVD button.
1-57
INTRODUCTION
EJECT, OPEN/CLOSE
Rear Panel
DVD/VCR OUT (VIDEO/AUDIO (Left/Right))
Connect to a TV with video and audio inputs.
LINE 1 (VIDEO IN/AUDIO IN (Left/Right))
Connect the audio/video output of an external source (Audio system, TV/Monitor,
Another VCR).
COMPONENT OUT (Y Pb Pr)
Connect to a TV with Y Pb Pr inputs.
ANALOG OUT (Left/Right) (DVD OUT)
Connect to a TV, amplifier, receiver, or stereo system.
Video Output Select Switch
Select either S-VIDEO or COMPONENT, depending
on how you connect DVD Player to the TV.
S-VIDEO OUT (DVD OUT)
Connect to a S-Video Input on TV.
AC Power Cord
Plug into the power source.
DIGITAL AUDIO OUT (OPTICAL) (DVD OUT)
Connect to digital (optical) audio equipment.
UHF/VHF OUT (DVD/VCR OUT)
Connect to a TV with RF coaxial inputs.
DIGITAL AUDIO OUT (COAXIAL) (DVD OUT)
Connect to digital (coaxial) audio equipment.
UHF/VHF IN (ANTENNA INPUT)
Connect the VHF/UHF/CATV antenna to this terminal.
Do not touch the inner pins of the jacks on the rear
panel. Electrostatic discharge may cause permanent
damage to the unit.
1-58
Connections
z
z
z
Depending on your TV and other equipment you wish to
connect, there are various ways you could connect the
DVD+VCR. Use connections described on pages 11-14.
Please refer to the manuals of your TV, VCR, Stereo
System or other devices as necessary to make the best
connections.
For better sound reproduction, connect the DVD+VCR’s
DVD/VHS AUDIO OUT jack to the audio in jacks of your
amplifier, receiver, stereo or audio/video equipment. See
Optional, Preferred TV Connections on page 13-14.
Caution
z
z
z
Make sure the DVD+VCR is connected directly to the TV.
Tune the TV to the correct video input channel.
Do not connect the DVD+VCR’s DVD/VHS AUDIO OUT
jack to the phono in jack (record deck) of your audio
system.
Do not connect your DVD+VCR via your VCR. The DVD
image could be distorted by the copy protection system.
Connecting Antenna/Cable TV to
DVD+VCR
If your cable wire is connected to your TV without a converter
or descrambler box, unscrew the wire from your TV and attach
it to the ANT.IN jack on the DVD+VCR. Use the supplied round
coaxial cable to connect between the DVD+VCR’s RF.OUT
jack and the 75 ohm antenna input jack on the TV. With this
connection, you can receive all midband, super band, and
hyperband channels.
With Cable Box
If a converter is required in your cable system, follow the
instruction below:
The cable hookup permits both TV and DVD+VCR operation.
To view or record CATV channel
1 Tune the TV to the DVD+VCR output channel (CH 3 or 4).
2 Set the DVD+VCR channel selector to the output channel of
the Cable Converter box by pressing the CH/TRK (+/-) or
number (0-9) of your DVD+VCR. (Example: CH3)
3 Select the channel to view at the Cable Converter Box.
Notes
z
z
the antenna leads from the rear of the
1 Disconnect
TV.
the type of cable from your antenna. If it is
2 Identify
a round cable as illustrated, it is a 75 ohm coaxial
antenna cable. This cable will connect directly to
With this connection, you CANNOT record one program
while viewing another.
If you are using a cable box to tune channels, it is not necessary to do Auto Channel Programming(Auto Channel Set)
as indicated on page 16.
Cable TV
Wall Jack
Back Panel of
Typical Cable Box
the jack marked ANT.IN on your DVD+VCR.
Tip
If your antenna lead wire is a flat type antenna cable,
connect it to a Antenna Adaptor (300-ohm to 75-ohm)
(not supplied) and slip the Adaptor onto the ANT.IN
jack. The Adaptor does not screw on to the DVD+VCR,
it just slips over the jack.
Antenna
Antenna
Cable TV
Wall Jack
Flat Wire
(300 ohm)
Rear of DVD+VCR
300/75 ohm
Adaptor
(Not supplied)
OR
OR
Rear of DVD+VCR
1-59
PREPARATION
Without Cable Box
Tips
Connections (Continued)
Basic TV Connections
Rear of TV
Make one of the following connections, depending on
the capabilities of your existing equipment.
z
ANTENNA
INPUT
AUDIO INPUT
L
VIDEO
INPUT
R
RF coaxial connection
Connect the RF.OUT jack on the DVD+VCR to the
antenna in jack on the TV using the 75-ohm Coaxial
Cable supplied (R).
R
Note
If you use this connection, tune the TV to the
DVD+VCR’s RF output channel (CH 3 or 4).
How to set the DVD+VCR’s RF output channel
1. When the DVD+VCR is turned off, press and hold
CHANNEL v or CHANNEL V on the front panel for
about five seconds.
It will turn itself on and “RF 03” or “RF 04” appears in the
display window.
2. Press CHANNEL v or CHANNEL V on the front
panel or CH/TRK (+/-) on the remote control to
change the RF output channel (CH 03 or CH 04).
3. Turn off and on the DVD+VCR.
4. Press the TV CH to 3 or 4 depending on the RF
output channel you had selected.
Now you can watch the DVD+VCR playback on CH3
or CH4 of your TV.
Rear of DVD+VCR
Audio/Video connection
1
Connect the DVD/VHS VIDEO OUT jack on the
DVD+VCR to the video in jack on the TV using the
video cable supplied (V).
the Left and Right DVD/VHS AUDIO OUT
2 Connect
jacks on the DVD+VCR to the audio left/right in
jacks on the TV (A1) using the supplied audio
cables.
Note
If you use this connection, set the TV’s source selector
to VIDEO.
1-60
A1
V
Connections (Continued)
Optional, Preferred TV Connections
z
S-VIDEO
INPUT
Notes
You can ONLY watch and listen to DVD playback
through the connections shown below.
When using the COMPONENT VIDEO OUT jacks,
set the video output select switch to COMPONENT. When using the S-VIDEO OUT jack, set the
video output select switch to S-VIDEO.
COMPONENT VIDEO INPUT
Pr
S
C
Pb
AUDIO INPUT
Y
R
L
A2
S-Video connection
1
Connect the S-VIDEO OUT jack on the DVD+VCR
to the S-Video in jack on the TV using the optional
S-Video cable (S).
the Left and Right AUDIO OUT jacks of
2 Connect
the DVD+VCR to the audio left/right in jacks on the
TV using the supplied audio cables (A2).
Component Video (Color Stream®) connection
1
Connect the COMPONENT VIDEO OUT jacks on
the DVD Player to the corresponding in jacks on
the TV using an optional Y Pb Pr cable (C).
Rear of DVD+VCR
the Left and Right AUDIO OUT jacks of
2 Connect
the DVD+VCR to the audio left/right in jacks on the
TV (A2) using the supplied audio cables.
Note
If the TV has an S-video input, connect the DVD player
with the S-video cable. When using an S-video cable,
do not connect the yellow video cable.
Progressive Scan (ColorStream® pro) connection
z
z
1
If your television is a high-definition or “digital ready”
television, you may take advantage of the DVD
Player’s progressive scan output for the highest
video resolution possible.
If your TV does not accept the Progressive Scan format, the picture will appear scrambled if you select
Progressive Scan output from the DVD Player.
Connect the COMPONENT VIDEO OUT jacks on
the DVD Player to the corresponding in jacks on
the TV using an optional Y Pb Pr cable (C).
the Left and Right AUDIO OUT jacks of
2 Connect
the DVD Player to the audio left/right in jacks on the
TV (A2) using the supplied audio cables.
Notes
– Set the Progressive to “On” from the setup menu, see
page 19.
– Progressive scan does not function simultaneously
with the analog video connections (yellow VIDEO
OUT jack).
1-61
PREPARATION
z
Rear of TV
Connections (Continued)
Optional, Preferred TV Connections
Rear of DVD+VCR
Note
You can ONLY listen to DVD playback using COAXIAL
(X), OPTICAL (O) and AUDIO OUT (A2) connections.
The tuner and VCR will still be heard through the
RF.OUT (R) or DVD/VHS AUDIO OUT (A1) jack. (See
page 12.)
Connecting to an amplifier equipped with two
channel analog stereo or Dolby Surround
A1
Connect the Left and Right AUDIO OUT (or DVD/VHS
AUDIO OUT) jacks on the DVD+VCR to the audio left
and right in jacks on your amplifier, receiver, or stereo
system using the audio cables (A1, A2) supplied.
Connecting to an amplifier equipped with two
channel digital stereo (PCM) or to an Audio/Video
receiver equipped with a multi-channel decoder
(Dolby Digital™, MPEG 2, or DTS)
1
Connect one of the DVD+VCR’s DIGITAL AUDIO
OUT jacks (OPTICAL O or COAXIAL X) to the corresponding in jack on your amplifier. Use an optional digital (optical O or coaxial X) audio cable.
will need to activate the DVD+VCR’s digital
2 You
output. (See Digital Audio Output on page 20).
A2
L
X
R
COAXIAL
AUDIO INPUT
O
OPTICAL
DIGITAL INPUT
Amplifier (Receiver)
Accessory Audio/Video (A/V) Connections to
DVD+VCR
Connect the VHS IN 1 or AV INPUT jacks on the
DVD+VCR to the audio/video out jacks on your
accessory component, using the optional audio/video
cables.
Accessory Component:
VCR, Camcorder,
Video Camera,
Satellite Receiver,
Laser Disc Player
Digital Multi-channel sound
A digital multi-channel connection provides the best
sound quality. For this you need a multi-channel
Audio/Video receiver that supports one or more of the
audio formats supported by your DVD+VCR (MPEG 2,
Dolby Digital and DTS). Check the receiver manual and
the logos on the front of the receiver.
Jack panel of Accessory
AUDIO
OUTPUT
R
L
Caution:
Due to the DTS Licensing agreement, the digital output
will be in DTS digital out when DTS audio stream is
selected.
VIDEO
OUTPUT
Notes
– If the audio format of the digital output does not match
the capabilities of your receiver, the receiver will
produce a strong, distorted sound or no sound at all.
– Six Channel Digital Surround Sound via digital connection can only be obtained if your receiver is
equipped with a Digital Multi-channel decoder.
– To see the audio format of the current DVD in the onscreen display, press AUDIO.
OR
Rear of DVD+VCR
1-62
Front of DVD+VCR
Before Operation - VCR Part
Some of these functions will be displayed every time the
VCR is operated.
❶
❷
❸
PLAY
SP
HI-FI
JUL 5 , SAT
❹
❺
CH 4
STEREO
2:15 PM
❻
❶ TAPE SPEED DISPLAY
❼
If the Extended Data Service (XDS) signals are provided
along with normal TV signal in your area or during playback of a tape recorded with Extended Data Service
(XDS) signals, the station ID, program title and program
details are shown on the TV screen.
When viewing a channel with Extended Data Service
(XDS) signals, press ENTER then the station ID will
appear on the TV screen. Press ENTER again and the
program details will appear on the TV screen.
When viewing a tape recorded with Extended Data
Service (XDS) signals, press ENTER twice then the program title and program details will appear on the TV
screen.
Program Details
Shows the current tape speed.
LENGTH: Indicates the run length of a program.
TIME REMAINING: Indicates the remaining time of a
program.
RATING: Indicates the rating of the current program
(N/A, G, PG, PG-13, R, NC-17, X and Not Rated). The
rating N/A means that the motion picture ratings are not
applicable to this program.
❷ FUNCTION DISPLAY
Indicates the function in progress.
❸ HI-FI DISPLAY
Indicates when this unit is playing back tape recorded with
Hi-Fi.
❹ CHANNEL DISPLAY
Indicates the selected channel (or LINE1, LINE2).
❺ STEREO/SAP DISPLAY (MONO is not displayed)
SP
WABC
CH 4
STEREO
PROGRAM DETAILS
“Home video”
Shows the type of audio signal received by the VCR tuner.
❻ DATE DISPLAY
“Home video”
JUL 5 , SAT
Shows the current date. (Month/Date/Day of the week
format)
Shows the current time, the tape counter and remaining time
on the tape.
Each press of the ENTER changes the TV screen in the
following sequence.
STOP
SP
2:15 PM
Easy Information Screen
(Station ID)
❼ CLOCK/COUNT/REMAIN DISPLAY
CH 4
STEREO
LENGTH 01:00
TIME REMAINING 00:26
RATING N/A
Easy Information Screen
(Program details)
Setting the On-Screen Display
The SETUP, clock setting, and timer recordings are
accessed conveniently with On-Screen Menu Displays
that lead you through each step. The following pages
describe the On-screen selections to be set.
Menu Selection
JUL 5 , SAT
Your VCR allows remote control adjustment of several
features.
Press VCR MENU and the MAIN menu will
appear.
1
Select the desired menu with v/V button and
2 then
press ENTER.
2:15 PM
2:15 PM
0:35:40
REM 1:58
MAIN MENU
Notes
z
z
z
The function displays can be seen displayed on the TV
screen for 5 seconds.
The clock (or tape counter, tape remaining) mode will continue until you press ENTER.
The tape counter and the remaining tape length indicator
appear only when a cassette is inserted. Also, the remaining
tape length indicator appears after any tape operation.
CLOCK SET (page 17)
PROGRAM (page 24)
TUNING (page 16)
SETUP (page 16)
Note
Menus remain on-screen for 3 minutes.
3 Press VCR MENU when finished.
1-63
PREPARATION
Easy Information
On-Screen Display (OSD)
Before Operation - VCR Part (Continued)
Setting the VCR Setup Menu
Channel Selection
VCR MENU and the MAIN menu will
1 Press
appear.
Press v/V to select the SETUP menu, then
2 press
ENTER.
The SETUP menu will appear.
This DVD+VCR is equipped with a frequency
synthesized tuner capable of receiving up to 181
channels. These include VHF channels 2-13, UHF
channels 14-69 and CATV channels 1-125.
Preparation:
z
Connect the DVD+VCR to the desired type of antenna or
cable TV system, as shown in Connecting Antenna/Cable TV
to DVD+VCR on page 11.
AUTO CHANNEL PROGRAMMING
VCR MENU and the MAIN menu will
1 Press
appear.
v/V to select the TUNING menu, then
2 Press
press ENTER.
The TUNING menu will appear.
Press v/V to choose a desired option on the
3 SETUP
menu. Then press b/B to choose a
desired setting.
FUNCTION OSD
The on-screen display of this DVD+VCR can be turned on or off.
z FUNCTION OSD can be switched between ON and OFF by
pressing b/B.
LANGUAGE SELECT
The on-screen programming of this DVD+VCR can be
displayed in either English, Spanish, or French.
z LANGUAGE SELECT can be switched among ENGLISH,
SPANISH and FRENCH by pressing b/B.
AUDIO MODE
The DVD+VCR has two separate audio playback systems, the
high quality VHS Hi-Fi system and standard NORMAL mono system. The same audio is generally recorded on both systems. The
VHS Hi-Fi system plays on separate (left and right) channels, and
the NORMAL system plays monaural sound. The normal track is
always played so the cassette can be played on a DVD+VCR that
does not have VHS Hi-Fi.
z AUDIO MODE can be switched between HI-FI and
NORMAL by pressing b/B.
BROADCAST TYPE (STEREO/SAP/MONO)
Multichannel Television Sound (MTS) carries stereo and/or
Second Audio Program (SAP) bilingual signals. Set this display to
the desired position when both MTS stereo and SAP signals are
received. When only one of the MTS signal is received, the
DVD+VCR automatically selects the corresponding receiving
mode (Stereo or SAP) regardless of the selected position. For
normal operation, the display should be in the STEREO position.
The DVD+VCR will then record a STEREO program when available,
and record a mono program IF the program is NOT IN STEREO.
For weak STEREO and/or SAP broadcasts, changing the display to mono may give clearer sound.
z BROADCAST TYPE can be switched among STEREO, SAP,
and MONO by pressing b/B.
AUDIO OUTPUT (STEREO/LEFT/RIGHT)
Used during playback [when AUDIO MODE (HI-FI/NORMAL) is
in HI-FI position] for selecting the audio output signals from the
AUDIO OUT terminals (L ch and R ch), and RF.OUT.
This display setting should normally be left in the stereo position, so that when a stereo tape is played, the stereo sound will
be heard through the left and right channels. If a mono tape is
played and the audio output is set to stereo, the same mono
sound will be heard from both left and right channels.
z AUDIO OUTPUT can be switched among STEREO, LEFT,
and RIGHT by pressing b/B.
4
Press VCR MENU when finished.
Press V to choose the SOURCE SELECT option,
3 then
press b/B to select TUNER.
bB
Press / repeatedly to switch among TUNER, LINE1
and LINE2.
Press v/V to choose the AUTO CHANNEL SET
4 option,
then press b/B to set the channel.
The tuner will automatically cycle through all
available channels in the area and place them in
the tuner’s memory.
the AUTO CHANNEL SET PROCEEDING is
5 After
complete, make sure the TUNING BAND is set
appropriately (TV or CATV) by pressing v/V and
choosing the correct TUNING BAND (TV or
CATV) by pressing b/B using the TUNING
menu.
Remember, TV is for the air antenna reception,
CATV is for cable or wireless cable connection.
6 Press VCR MENU to return to the TV screen.
Use CH/TRK (+/-) or CHANNEL (v/V) on the
7 front
panel to cycle the DVD+VCR through the
channels in memory.
TO ADD OR ERASE CHANNELS FROM MEMORY
This feature allows you to add or erase channels from
memory manually.
1
Press V to choose the CH. ADD/DEL option on the
TUNING menu. Press b/B to select a channel to
add or erase.
2
Press ENTER to add or erase the channel.
Repeat steps 1 and 2 to add or erase channels.
3
Press VCR MENU to return to the TV screen.
1-64
Before Operation - VCR Part (Continued)
Setting the Clock
Manual Clock Set
Things to know before starting
z
z
There are cases where the TV station does not send or sends
wrong date and/or time information and the DVD+VCR sets the
incorrect time.
If this happens we recommend that you set the clock manually.
The clock uses the 12-hour system. (Be sure to set AM
and PM correctly.)
The initial Clock Setting is JANUARY 1, 2003, 12:00 AM.
Example: July 5, 2003 ; 2:15 AM
VCR MENU and the MAIN menu will
1 Press
appear.
Press v/V to choose the CLOCK menu.
2 Press
ENTER and the CLOCK menu will appear.
Auto Clock Set
The Auto Clock Set feature is set to ON at the factory. In the
ON setting, the DVD+VCR looks for a channel carrying XDS
(Extended Data Services) information. XDS updates the clock
using the Coordinated Universal Time.
The Auto Clock Feature enables the DVD+VCR to set up
the clock when the DVD+VCR is turned off.
VCR MENU and the MAIN menu will
1 Press
appear.
Press b/B to choose the month.
Press v/V to choose the CLOCK menu.
3
2 Press ENTER and the CLOCK menu will appear.
Press V to choose the DAY option.
4 Use
b/B to choose the day.
The day of the week will display automatically.
V to choose the AUTO CLOCK SET option.
3 Press
Press b/B to choose ON.
The Auto Clock Set feature is set to ON at the factory. In
the ON setting, the DVD+VCR looks for a channel
carrying XDS (Extended Data Services) information. XDS
updates the clock using the Coordinated Universal Time.
4
Press
item.
Press
Press V to choose the YEAR option.
5 Use
b/B to choose the year.
Press V to choose the TIME option.
6 Use b/B to choose the time.
Press and hold
continuously.
7
V to choose the DAYLIGHT SAVINGS
b/B to advance clock
Press E to choose the DAYLIGHT SAVINGS
item.
Use b/B to choose AUTO, ON or OFF.
If you choose AUTO, the VCR sets the clock using the
DST information broadcast in the signal (channel).
If you choose ON, the VCR sets the clock when the
Daylight Saving Time is started and ended.
b/B to choose AUTO, ON or OFF.
If you choose AUTO, the VCR sets the clock using the
DST information broadcast in the signal (channel).
If you choose ON, the VCR sets the clock when the
Daylight Saving Time is started and ended.
V to choose the TIME ZONE item.
5 Press
Press b/B to choose the correct time zone
(AUTO, EASTERN, CENTRAL, MOUNTAIN,
PACIFIC, ALASKA or HAWAII).
If “AUTO” is selected as the time zone, the VCR sets the
clock using the first Coordinated Universal Time information it finds in a broadcast signal.
6 Press VCR MENU when finished.
off the DVD+VCR and the auto clock set7 Turn
ting works.
8 Press VCR MENU when finished.
Note
If setting the clock manually, “AUTO CLOCK SET” must
set to “OFF”.
If set to “ON”, an incorrect date and/or time will be
entered again when the DVD+VCR is turned off.
1-65
PREPARATION
Note
The DVD+VCR gives you two ways to set the time and
date: the Auto Clock Feature or manually. The Auto
Clock Feature enables the DVD+VCR to set up the clock
when the DVD+VCR is turned off.
Before Operation - DVD Part
Temporary Feedback Field Icons
General Explanation
This manual gives the basic instructions for operating
the DVD+VCR. Some DVDs require specific operation
or allow only limited operation during playback. When
this occurs, the symbol
appears on the TV screen,
indicating that the operation is not permitted by the
DVD+VCR or is not available on the disc.
TITLE
CHAPT
TRACK
ALL
On-Screen Display
A
The general playback status can be displayed on the
TV screen. Some options can be changed on the menu.
OFF
Repeat Chapter
Repeat Track (non-PBC Video CDs
and Audio CD only)
Repeat Disc (non-PBC Video CDs
and Audio CD only)
Repeat A-B
Repeat Off
Resume play from this point
Action prohibited or not available
On-screen display operation
1 Press DISPLAY during playback.
Use v/V to select an option.
2 The
selected option will be highlighted.
b/B to change the setting of an option.
3 Use
The number buttons can also be used for setting
numbers (e.g., title number). For some functions,
B
Repeat Title
z
z
Notes
Some discs may not provide all of the features on the
on-screen display example shown below.
If no button is pressed for 10 seconds, the on-screen
display disappears.
press ENTER to execute the setting.
DVD
Function (Press v/V to select desired option)
Options
1/3
Shows the current title number and total number of
titles, and skips to the desired title number.
b/B, or
Numeric, ENTER
1/12
Shows the current chapter number and total number of
chapters, and skips to the desired chapter number.
b/B, or
Numeric, ENTER
Shows the elapsed playing time, and
searches the point by the elapsed time directly.
Numeric, ENTER
Title Number
Chapter Number
Time search
Audio language
and Digital Audio
Output mode
Subtitle language
Angle
VCD2.0
0:16:57
1 ENG
D
5.1 CH
OFF
1/1
Sound
NORM.
Shows the current audio soundtrack language,
encoding method, and channel number, and
changes the setting.
Shows the current subtitles language, and
changes the setting.
Shows the current angle number and total number of
angles, and changes the angle number.
Shows the current sound mode, and
changes the setting.
b/B, AUDIO
b/B, SUBTITLE
b/B, ANGLE
b/B
VCD1.1
Function (Press v/V to select desired item)
Items
Track Number
1/4
Time
Audio Channel
Sound
Selection Method
0:16:57
Displays the current track number, total number of tracks
and PBC On mode, and skips to the desired track number.
Displays the elapsed playing time (Display only)
Selection Method
b / B, or
Numbers, ENTER
–
STER.
Displays the audio channel, and
changes you make to the audio channel.
b/B
NORM.
Displays the current sound mode, and
any changes you make to the setting.
b/B
1-66
Before Operation - DVD Part (Continued)
Picture
You can set your own Personal Preferences on the
DVD+VCR.
TV Aspect
4:3 Letterbox: Select when a standard 4:3 TV is connected. Displays theatrical images with masking bars
above and below the picture.
4:3 Panscan: Select when a standard 4:3 TV is connected. Displays pictures cropped to fill your TV screen.
Both sides of the picture are cut off.
16:9 Wide: Select when a 16:9 wide TV is connected.
General Operation
1
2
Press SETUP.
The setup menu appears.
Disc Audio
Original
Disc Subtitle
English
Disc Menu
French
Rating
German
Area Code
Spanish
TV Aspect
Italian
Menu Language
Chinese
Progressive Scan
Polish
Digital Audio Output
Hungarian
5.1 Speaker Setup
Russian
Others
Other — — — —
Disc Audio
4:3 Letterbox
Disc Subtitle
4:3 Panscan
Disc Menu
16:9 Wide
Rating
Area Code
TV Aspect
Menu Language
Progressive Scan
Use v/V to select the desired option.
The screen will show the current setting for the
selected option, as well as alternate setting(s).
Digital Audio Output
5.1 Speaker Setup
Others
the desired option is selected, press B,
3 While
then v/V to select the desired setting.
ENTER to confirm your selection.
4 Press
Some options require additional steps.
SETUP, RETURN, or PLAY to exit the
5 Press
setup menu.
Progressive Scan
Language
Disc Language
DVD
DVD
Select a language for the disc’s Menu, Audio, and Subtitle.
DVD
Progressive Scan Video provides the highest resolution
pictures with less flicker and line structure.
If you are using the COMPONENT VIDEO OUT jacks,
but are connecting the DVD Player to a standard (analog) television, set Progressive Scan to Off.
If you are using the Component Video jacks for
connection to a TV or monitor that is compatible with a
progressive scan signal, set Progressive Scan to On.
Original : The original language set for the disc is selected.
Other : To select another language, press number buttons to enter
the corresponding 4-digit number according to the language code
list on page 42. If you enter the wrong language code, press
CLEAR.
Disc Audio
Off
Disc Subtitle
On
Disc Menu
Rating
Area Code
TV Aspect
Notes
Disc Language selection may not work for some DVDs.
Menu Language
Progressive Scan
Digital Audio Output
Disc Audio
Original
5.1 Speaker Setup
Disc Subtitle
English
Others
Disc Menu
French
Rating
German
Area Code
Spanish
TV Aspect
Italian
Menu Language
Chinese
Progressive Scan
Polish
Digital Audio Output
Hungarian
5.1 Speaker Setup
Russian
Others
Other — — — —
Notes
– Progressive Scan is available only when the VIDEO
OUTPUT switch on the rear panel is set to COMPONENT.
Menu Language
Select a language for the setup menu. This is the menu
you see when you press SETUP.
Disc Audio
English
Disc Subtitle
Spanish
Disc Menu
French
Rating
Area Code
TV Aspect
Menu Language
Progressive Scan
Caution
Once the setting for progressive scan output is entered, an
image will only be visible on a progressive scan compatible
TV or monitor. If you set Progressive Scan to On in error,
you must reset the unit. Pointing the remote at the player,
press the STOP key to stop any disc that is playing. Next,
press the STOP key again and hold it for five seconds
before releasing it. The video output will be restored to the
standard setting, and a picture will once again be visible on
a conventional analog TV or monitor.
Digital A dio O tp t
1-67
PREPARATION
Initial Settings
Before Operation - DVD Part (Continued)
Sound
Dynamic Range Control (DRC)
Digital Audio Output
With the DVD format, you can hear a program’s soundtrack in the most accurate and realistic presentation
possible, thanks to digital audio technology. However,
you may wish to compress the dynamic range of the
audio output (the difference between the loudest sounds
and the quietest ones). Then, you may listen to a movie
at a lower volume without losing clarity of sound. Set
DRC to On for this effect.
Each DVD disc has a variety of audio output options.
Set the DVD+VCR’s Digital Audio Output according to
the type of audio system you use.
DOLBY DIGITAL/PCM: Select DOLBY DIGITAL/PCM if
you connected the DVD+VCR’s DIGITAL AUDIO OUT
jack to a Dolby Digital decoder (or an amplifier or other
equipment with a Dolby Digital decoder).
Stream/PCM: Select Stream/PCM if you connected the
DVD+VCR’s DIGITAL AUDIO OUT jack to an amplifier
or other equipment with a DTS decoder, Dolby Digital
decoder or MPEG decoder.
PCM: Select when connected to a 2 channel digital
stereo amplifier. The DVD+VCR output sounds in the
PCM 2ch format when you play a DVD video disc
recorded with a Dolby Digital, MPEG1, or MPEG2
recording system.
Disc Audio
DOLBY
DIGITAL
Disc Subtitle
Stream/PCM
Disc Menu
PCM
/PCM
Set Vocal to On only when a multi-channel karaoke
DVD is playing. The karaoke channels on the disc will
mix into normal stereo sound.
PBC
Set Playback Control (PBC) to On or Off.
On: Video CDs with PBC are played according to the PBC.
Off: Video CDs with PBC are played the same way as Audio
CDs.
B.L.E. (Black Level Expansion)
Rating
Area Code
Vocal
Sample Freq.
TV Aspect
48 KHz
Menu Language
96KHz
Progressive Scan
To select the black level of playback pictures. Set your
preference and monitor’s ability.
On: Expanded grey scale. (0 IRE cut off)
Off: Standard grey scale. (7.5 IRE cut off)
Digital Audio Output
5.1 Speaker Setup
Others
Pluge (Blacker than Black)
Sample Frequency
To change the Sample Frequency setting, first select
the desired Digital Audio Output as indicated as above.
If your receiver or amplifier is NOT capable of handling
96KHz signals, select 48KHz. When this choice is
made, this unit will automatically convert any 96KHz
signals to 48KHz so your system can decode them.
If your receiver or amplifier is capable of handling
96KHz signals, select 96KHz. When this choice is
made, this unit will pass each type of signal through
without any further processing.
For proper adjustment of your television brightness
settings utilizing a commercially available test disc.
On: Select when you adjust the level of your TV using a
commercially available test disc that contains pluge
signals.
Off: For normal use.
DNR (Digital Noise Reduction)
You can reduce ambient noise in the picture.
DNR1: Normal level
DNR2: Expanded level.
Off:
Off.
Others
The DRC, Vocal, PBC, B.L.E., Pluge and DNR settings
can be changed.
z Press v/V to select the desired item and press
ENTER. The setting of the selected item alternates
between On and Off.
Disc Audio
DRC
Disc Subtitle
Vocal On
Disc Menu
PBC
Rating
B.L.E. Off
Area Code
Pluge Off
TV Aspect
DNR
Menu Language
On
On
Off
Notes
– Actual picture enhancement may vary depending on the
quality of the disc.
– While the DNR2 (expanded level) can provide additional
improvement in the reduction of noise in the video signal, it
may produce undesirable picture artifacts on some discs.
Should this occur, select a more appropriate DNR level (normal or off).
– Depending on the disc, some picture detail may be lost by
the picture enhancement.
– A DVD audio disc with Dolby Digital or DTS soundtrack may
be played, some DVD audio discs include moving pictures
which may be modified by the above processes.
Progressive Scan
Digital Audio Output
5.1 Speaker Setup
Others
1-68
Before Operation - DVD Part (Continued)
Parental Control
Area Code
Rating
Enter the code of a country/area whose standards were
used to rate the DVD video disc, referring to the list
(See “Country/Area Code List”, page 43.).
Movies on DVDs may contain scenes not suitable for
children. Therefore, discs may contain Parental Control
information that applies to the complete disc or to
certain scenes on the disc. These scenes are rated
from 1 to 8, and alternatively, more suitable scenes are
available for selection on some discs. Ratings are
country dependent. The Parental Control feature allows
you to prevent discs from being played by your children
or to have certain discs played with alternative scenes.
Disc Audio
Code Set
Disc Subtitle
U S
Disc Menu
Rating
Area Code
TV Aspect
Menu Language
Progressive Scan
Digital Audio Output
Disc Audio
8
5.1 Speaker Setup
Disc Subtitle
7
Others
Disc Menu
6
Rating
5
Area Code
4
TV Aspect
3
Menu Language
2
Progressive Scan
1
Digital Audio Output
Unlock
5.1 Speaker Setup
Change
Select Area Code using the v/V buttons on the
1 setup
menu.
While Area Code is selected, press B.
2
3 Follow step 3 of “Rating” on left.
4 Select the first character using the v/V buttons.
Press 2 to shift to second character and select
5 the
second character using v/V buttons.
Press ENTER to confirm your Area code
6 selection, then press SETUP to exit the menu.
Others
Rating on the Setup menu using v/V
1 Select
buttons.
2 While Rating is selected, press B.
you have not entered a password yet.
3 When
Enter a 4-digit password using the numbered buttons to create a personal 4-digit security password,
then press ENTER. Enter the 4-digit password again
and press ENTER to verify.
When you have already entered a password;
Enter a 4-digit password using the numerical buttons to confirm the personal 4-digit security password, then press ENTER.
Note
Confirmation of the 4-digit password is necessary when
the password is changed (see Changing the 4-digit
password below ).
If you make a mistake before pressing ENTER, press
CLEAR and enter 4-digit security password again.
1 Follow Steps 1-2 as shown above to the left (Rating).
2 Enter the old password, then press ENTER.
3 Select Change using v/V buttons then press
ENTER.
4 Enter the new 4-digit password, then press ENTER.
5 Enter exactly the same password a second time and
verify by pressing ENTER.
6 Press SETUP to exit the menu.
a rating from 1 to 8 using v/V buttons.
4 Select
Level 1 : DVD software for adults cannot be
played back.
Level 8 : All DVD software can be played back.
The limitation will be more severe as the level
number is lower.
Unlock: If you select Unlock, Parental Control is
not active. The disc will play in full.
Ratings 1 to 8: Some discs contain scenes not suitable for children. If you set a rating for the DVD+VCR,
all disc scenes with the same rating or lower will be
played. Higher rated scenes will not be played unless
an alternative scene is available on the disc. The alternative must have the same rating or a lower one. If no
suitable alternative is found, playback will stop. You
must enter the 4-digit password or change the rating
level in order to play the disc.
ENTER to confirm your rating selection,
5 Press
then press SETUP to exit the menu.
Changing the 4-digit password
If you forget your 4-digit password
If you forget your password, clear the current password
by following the procedure below.
1 Press SETUP to display the setup menu.
Move the cursor down to “Rating”.
2 Use the Number buttons to enter “210499”. The
cursor will move up to “Disc Audio” automatically.
The 4-digit password is cleared.
3 Enter a new password as shown above to the left
(Rating).
1-69
PREPARATION
DVD
DVD
Operation with tape
Normal Playback
Search
Preparation:
This function lets you quickly and visually search for a
desired tape section in either direction: forward and
reverse.
z
z
z
z
Turn on the TV.
Tune the TV to the DVD+VCR output channel (CH 3 or 4) or
set the TV’s source selector to VIDEO.
If a direct VIDEO/AUDIO connection is made between the
DVD+VCR and the TV, set the TV’s source selector to VIDEO.
Set the Output Source to VCR as shown in Setting the
Output Source on page 6.
1
Insert a prerecorded video cassette.
3
1 Press PAUSE/STILL during playback.
Still picture will appear on the TV screen.
z
It is not necessary to select the tape speed for playback. It will be automatically selected by the DVD+VCR.
In playback, the TV/VCR selector switches to VCR
mode automatically.
If the tape reaches the end before STOP is pressed, the
DVD+VCR will automatically stop, rewind, eject, and it
will turn itself off.
z
z
z
3 To return to playback, press PLAY.
Slow Motion
z
z
When the AUTO TRK button is pressed.
A tape is played back for the first time.
Tape speed (SP, LP, SLP) changes.
Streaks or snow appear because of scratches on the tape.
Instant Skip
This is useful for skipping commercials or short program
segments.
1 Press INSTANT SKIP during the playback mode.
The tape will fast forward picture search through 30
seconds of recording.
In case of vertical jitter, adjust these controls very carefully.
Tracking is automatically reset to normal when the tape is
ejected or the power cord is unplugged for more than 3 seconds.
z
z
Special Effect Playbacks
z
z
The skipping time can be extended by pressing INSTANT
SKIP.
Subsequent presses result in advancing the fast forward
picture search time by 30-second increments (maximum 3
minutes).
2 When the search is completed, the DVD+VCR will go
into playback mode automatically.
Special effects playback notes
z
During slow playback, use CH/TRK (+/-) on the Remote
Control to minimize noise bands.
If slow motion mode continues for more than 3 minutes,
the DVD+VCR will automatically change to playback
mode.
2 To return to playback, press PLAY.
Manual Tracking
If noise appears on the screen during playback, press
either CH/TRK (+/-) on the remote control or
CHANNEL (v/V) on the front panel until the noise on
the screen is reduced.
z
2 Press PAUSE/STILL repeatedly to advance the
1 Press SLOW during playback or still mode.
The tape will be played back at a speed 1/19 times
slower than the normal speed.
Auto Tracking
The automatic tracking function adjusts the picture to
remove snow or streaks.
The AUTO TRACKING function works in the following
cases:
z
If a still picture vibrates vertically, stabilize it by pressing
CH/TRK (+/-) on the remote control.
If the DVD+VCR is left in the STILL mode for more than 5
minutes, the DVD+VCR will automatically enter the STOP
mode to protect the tape and video heads.
video picture one frame at a time while viewing a still
picture.
Tracking Control
z
z
Press STOP to stop playback.
STOP appears on the TV screen.
z
If the DVD+VCR is left in the SEARCH mode for more
than 3 minutes, the DVD+VCR will automatically enter the
PLAY mode, to protect the tape and video heads.
Still Picture and Frame-by-Frame
Playback
PLAY once.
2 Press
PLAY appears on the TV screen .
z
z
2 To return to playback, press PLAY.
The
indicator will light and the DVD+VCR will
power-up automatically.
z Make sure that the TIMER indicator in the display
window is not lighted. If it is, press POWER once.
z If a tape without a safety tab is inserted, the unit will
start playback automatically.
z
1 Press REW or FWD during playback.
The DVD+VCR will be activated in the SEARCH
mode.
Horizontal lines (noise bars) will appear on the TV screen. This
is normal.
The audio is automatically muted during special effect modes,
so there is no sound during search.
During the high-speed picture search modes, a short period is
needed to stabilize tape speed when re-entering the PLAY
mode. Slight interference may be observed during this period.
1-70
VISS (VHS Index Search System)
Normal Recording
The VHS INDEX SEARCH SYSTEM enables you to
locate the beginning of any recording made on this VCR.
Whenever a recording begins, an invisible INDEX mark is
recorded on the tape.
Preparation:
z
z
z
VISS Scan
VISS SCAN lets you search out each VISS mark on the
recorded tape and play 5 seconds before advancing to
the next VISS mark.
a cassette tape that has VISS signals
1 Insert
marked.
the VISS button once during PLAYBACK
2 Press
or STOP mode.
The VISS -- indicator will appear in the display win-
3
Turn on the power of both the DVD+VCR and TV.
Tune the TV to the DVD+VCR output channel (CH 3 or 4) or
set the TV’s source selector to VIDEO.
If a direct VIDEO/AUDIO connection is made between the
DVD+VCR and the TV, set the TV’s source selector to
VIDEO.
1 Insert a video cassette that the safety tab intact.
the desired channel by using CH/TRK
2 Select
(+/-).
z
If you are recording from another source via audio/video
input jacks (at the Rear or Front panel), select the
LINE1 or LINE2 by pressing INPUT SELECT.
the desired recording speed (SP or SLP) by
3 Set
pressing SP/SLP.
dow.
Press either the FWD or the REW button.
The VISS SCAN will start. The indicator appears
simultaneously during scanning. The tape will be
rewound or rapidly advanced to the next signal
marked.
The tape will be played back for approximately 5
seconds, and then rewound or rapidly advanced to
the next VISS signal.
z
This DVD+VCR is not designed to record in LP mode.
4
REC/OTR once.
5 Press
Recording will start. (The REC indicator will light in
the display window.)
Set the MTS mode as desired (See page 17, 27).
z Press VISS or STOP button to stop the VISS SCAN
mode.
z
REC indicator appears only when the Output Source is
set to VCR.
z
If a cassette with no safety tab is loaded, the cassette
will be ejected automatically.
the desired program, press the PLAY button.
4 AtNormal
playback of that program will begin.
6 Press STOP to stop recording.
If the tape reaches the end before STOP is pressed, the
DVD+VCR will automatically stop, rewind, eject, and it will
turn itself off.
VISS Search
You can locate the desired program and play it back
automatically by designating the number of its VISS signal. Up to the 99th VISS signal from the preset position
on the tape can be located.
1
2
3
Press the VISS button once during PLAYBACK
or STOP mode.
The VISS -- indicator will appear in the display window.
Enter the number of VISS signals you wish to
skip.
Up to 99 signals may be skipped from any given
position on the tape.
Press either the FWD or REW button once.
The SrCH 02 (for example) message appears in the
display window. When the desired VISS signal is
found, playback begins automatically.
z
To pause the recording
1 Press PAUSE/STILL to pause the tape during
recording.
The REC indicator will flash in the display window.
2 When you want to continue recording, press
PAUSE/STILL or press REC/OTR.
z
After 5 minutes in pause mode, the tape will be stopped
automatically to protect the tape and the video heads.
To record one TV program while
watching another
1 Press TV/VCR to select the TV mode during recording.
The VCR indicator disappears.
2 Using the TV, select the channel to be viewed.
If the end of the tape is reached during forward VISS
search, the VCR will automatically stop, rewind, eject,
and turn itself off.
Tips
Always use PAUSE/STILL for best results when making
changes during recording.
For example: To change channels during recording, first press
PAUSE/STILL to put the unit in pause mode. Then select the
desired channel on the DVD+VCR, and press PAUSE/STILL
again to resume recording.
1-71
OPERATION
Operation with tape (Continued)
Operation with tape (Continued)
Timer Recording
10
This DVD+VCR can be programmed to record up to 8
programs within a period of 1 year. For unattended
recording, the timer needs to know the channels to be
recorded and the starting and ending times.
Things to know before starting
z
z
If you try to set the program timer before setting the clock,
PLEASE SET THE CLOCK appears for a moment and
then CLOCK menu appears on the TV screen. Set the time
and date before proceeding.
Make sure a tape is in the DVD+VCR and the safety tab is
in place or the tape will be automatically ejected.
z
11
z
z
AUTO mode determines how much tape is left and
switches speed from SP to SLP, if necessary, to
complete recording the program. There will be some
picture and sound distortion at the point of the speed
change.
Use V to choose the REPEAT option.
Use b/B to choose the desired repeat (ONCE,
WEEKLY or DAILY).
ONCE event....for recording up to 8 programs on a
single day or over the days within a period of 1 year.
WEEKLY event....for recording up to 8 programs on a
certain day of every week.
DAILY event....for recording up to 8 programs at the
same time(s) Monday through Friday.
Preparation:
z
Use V to choose the SPEED option.
Use b/B to choose the desired recording
speed (AUTO, SP or SLP).
Turn on the power of both the DVD+VCR and the TV.
Be sure the TV is set to the DVD+VCR output channel (3 or 4).
Make sure the TUNING BAND in the TUNING menu is set
appropriately (TV or CATV).
VCR MENU and the MAIN menu will
1 Press
appear.
2 Use v/V to choose the PROGRAM menu.
ENTER to go to the PROGRAM menu.
3 Press
The PROGRAM menu will appear.
z
If all programs have already been entered, FULLY
PROGRAMMED message will appear for a moment
and then PROGRAM 1 will appear on the TV screen.
Tip
If the input data is wrong, use
and correct it using b/B.
12
Press VCR MENU, the program will be memorized at the DVD+VCR.
z
z
z
z
b/B to choose the PROGRAM No. (1-8).
4
V to choose the MONTH option.
5 Use
Use b/B to choose the desired month.
V to choose the DAY option.
6 Use
Use b/B to choose the desired day.
V to choose the START option.
7 Use
Use b/B to choose the desired start time.
Use
8
9
Press and hold
b/B to advance the clock faster.
Use V to choose the STOP option.
Use b/B to choose the desired stop time.
Press and hold b/B to advance the clock faster.
Use V to choose the CHANNEL option.
Use b/B to choose the desired channel
(Channel, LINE1 or LINE2).
Cable Users: If you have CABLE TV and used Cable Box
in Connecting Antenna/Cable TV to DVD+VCR (page 11),
using a cable box converter, you must set the channel in
this step to match the cable box output channel (usually
CH 3 or 4). Change channels on the cable box instead of
with the DVD+VCR.
v to select the data
TIMER indicator lights in the display window.
If the program preset time is past, the PAST TIME
PROGRAMMED message will appear on the TV
screen. Return to the incorrect program and program
it with the correct time.
If you had entered a past date, the timer recording
will be performed on that date of the next year.
Additional programs may be entered by repeating
steps 1-12.
Cable Users: If your cable hookup is via a TV converter box, you can program multiple recordings only on
the converter box output channel. This is because the
converter determines what channel you view through
your DVD+VCR.
Tip
If you have finished programming and you want to set the
DVD+VCR to record the programs you have entered.
MAKE SURE YOU HAVE INSERTED A TAPE INTO THE
DVD+VCR. The DVD+VCR is now set to record the preset
programs.
Note
If the power fails or the DVD+VCR is unplugged from the AC
outlet, the correct clock time and timer settings are kept in
memory for approximately 3 seconds. After 3 seconds, the
clock and program timer must be reset when power is
restored. Reset the clock according to instructions.
After setting a timer recording, it will start if a timer recording
passes over the start time when stopping the playback or
recording.
1-72
Operation with tape (Continued)
Programming can be checked whenever the DVD+VCR
is turned on.
1 Press VCR MENU and the MAIN menu will appear.
2 Use v/V to choose the PROGRAM menu.
Press ENTER and the PROGRAM menu will appear.
the desired recording speed (SP or SLP) by
3 Set
pressing SP/SLP.
The tape speed will appear on the TV screen.
4 Press REC/OTR twice.
REC/OTR repeatedly to select the
5 Press
recording time length.
At the end of the recording, the DVD+VCR will stop
The menu as illustrated, will appear on the TV screen.
z Recording will start. (The TIMER indicator will light)
recording and shut off.
z
z
3 Use b/B to select a program you want to check or
erase. If you want to erase the program, press
CLEAR.
4 Press VCR MENU to return to the TV screen.
ONE TOUCH TIMER RECORD MENU
ONE TOUCH TIMER RECORD
Program Priority
If the recording start and end
times of preset programs
overlap on the same day (see
the example and diagram
left), program number 2 will
not be recorded until program
number 1 is finished.
The first part of program number 2 will not be recorded.
The same thing will happen to program number 3.
One touch Timer Recording(OTR)
CHANNEL
SPEED
2
SP
START
LENGTH
NOW
0H30M
To extend the Recording Time
The recording time can be extended anytime by pressing REC/OTR.
Subsequent presses result in advancing the recording
time by 30-minute increments to a maximum fo 9 hours.
Notes
Preparation:
z
z
Turn on the power of both the DVD+VCR and the TV.
Be sure the TV is tuned to the DVD+VCR output channel (3
or 4).
If a direct VIDEO/AUDIO connection is made between the
DVD+VCR and the TV, set the TV’s source selector to
VIDEO.
1 Insert a video cassette with the safety tab intact.
the desired channel by using CH/TRK
2 Select
(+/-) or number (0-9).
The channel number appears on the TV screen.
z
Length Display
(each additional press of
REC/OTR increases
recording time 30 minutes)
Press REC/OTR once to check the recording time. The
recalled setting will automatically return to the TV
screen after 6 seconds.
z
z
0H30M ..... 9H00M ➝ 0H00M
Checking the Recording Time
One touch Timer Recording allows you to make a
recording easily of a preset length without using the
program timer.
z
During One touch Timer Recording, changing the channel on the DVD+VCR will not be possible.
You can stop the recording by pressing STOP.
If you are recording from another source via audio/video
input jacks (at the Rear or Front panel), select the
LINE1 or LINE2.
1-73
If you press PAUSE/STILL during One touch timer recording,
the DVD+VCR will enter the recording pause mode. Instant
timer recording is cancelled.
If the DVD+VCR is set to “0H00M”, the DVD+VCR goes to
normal recording mode.
OPERATION
Checking (Erasing) the Timer Program
Operation with tape (Continued)
Dubbing and Editing
Copying from DVD to VCR
If you wish to edit or dub your camcorder (or another
VCR) recordings to this DVD+VCR, the rear (or Front)
panel mounted Audio and Video (A/V) input jacks
make the connections quick and easy. These direct
A/V jacks will also provide better picture results than
using the RF jack on the rear panel.
This unit allows you to copy the contents of a DVD to a
VHS tape.
1
Connect the camcorder’s (or another VCR’s) A/V
outputs to your DVD+VCR as illustrated on page
14.
the input channel “LINE2”. (press INPUT
2 Set
SELECT to select LINE2.)
z
If you have connected your DVD+VCR to the A/V
input jacks on the rear of DVD+VCR, you should
select the input channel LINE1 by pressing INPUT
SELECT twice.
the tape in the camcorder (or another
3 Play
VCR). If you have a TV attached to your
DVD+VCR, you can see the video playing.
4
When your desire recording begins, press
DVD+VCR’s REC/OTR once to start.
Note
Before recording, please confirm the recording start position.
Note
If the DVD you are attempting to copy is copy protected,
you will not be able to copy the disc. It is not permitted
to copy Macrovision encoded DVDs. “Lock” is
displayed in the display window.
1
Insert Disc
Insert the disc you wish to copy in the DVD deck
and close the disc tray.
VHS Tape
2 Insert
Insert a blank VHS video tape into the VCR deck.
PLAY on the DVD deck.
3 Press
The DVD will go into play mode
z
If the DVD disc menu appears, you may need to press
the PLAY manually to begin copying.
4 Press REC on the VCR deck.
z
z
The DVD+VCR will go into Record mode.
“CDREC” indicator will light.
5 Stop the Copy Process
When the DVD is finished playing, press the VCR on the
remote control and then press STOP ( ) to end the copy.
You must stop the Copy process manually when the DVD
movie ends, or the unit may replay and record over and
over again.
x
Note
When you stop the DVD playback during copying, the recording on VCR is stopped automatically.
1-74
Operation with tape (Continued)
MTS (Multi-Channel TV Sound)
This DVD+VCR is equipped with the VHS Hi-Fi audio
sound system for recording and playback. The information below gives a brief description of Hi-Fi audio and
how to record and play a tape in the Hi-Fi audio mode.
This DVD+VCR will decode MTS stereo and bilingual
(SAP) off-the-air broadcast sound signals. It also
decodes stereo TV sound from local cable companies,
as long as they operate on assigned cable frequencies
and use the EIA-recommended MTS stereo/bilingual TV
sound system.
Playback with Hi-Fi Stereo Audio Sound
Multichannel TV Sound Indicator (MTS)
A stereo TV with AUDIO/VIDEO input jacks or a stereo
audio system is required for true stereo playback. To
experience the full and rich stereo sound available with
Hi-Fi recorded tapes, we recommend the connection of
this unit to a home stereo audio system.
Shows Onscreen as illustrated below when ENTER is
pressed.
1
z
One or both of the indicators will light, depending on the
MTS broadcast.
TV screen
CH 4
STEREO/SAP
Set the AUDIO MODE option to HI-FI on the
SETUP menu .
STEREO
Lights up when a stereo broadcast
is being received.
SAP
Lights up when a SAP BILINGUAL
broadcast is being received.
If only STEREO appears on the TV screen.
The DVD+VCR can record in stereo onto the VHS Hi-Fi audio
tracks when the BROADCAST TYPE option is in the STEREO
position. The DVD+VCR will also record mono audio onto the
mono audio track.
2
If only SAP appears on the TV screen.
Set the AUDIO OUTPUT option to STEREO
position.
Set the BROADCAST TYPE option to SAP.
(STEREO) POSITION: The left channel sound (L) is
heard from the left speaker and the right channel sound
(R) is heard from the right speaker.
(LEFT) POSITION: The left channel sound (L) is heard
from both speakers.
(RIGHT) POSITION: The right channel sound (R) is heard
from both speakers.
If STEREO/SAP appears on the TV screen
Use the BROADCAST TYPE option to select the desired
recording mode (STEREO or SAP).
SAP (Second Audio Program) Recording
Some stations transmit a Second Audio Program, which
is used for a second language or additional information.
When the station broadcasts a Second Audio Program,
follow the procedure below to record the SAP.
Insert a video cassette with the safety tab intact.
1 Set the BROADCAST TYPE option to SAP
2 (SETUP menu).
Do this if only the SAP appears on the TV screen or you
know the program will use the SAP.
3 Press VCR MENU.
a cassette and press PLAY.
4 Insert
Adjust volume at your stereo system.
3 Press VCR MENU.
the desired recording speed (SP or SLP) by
4 Set
pressing SP/SLP.
the desired channel. The SAP should
5 Select
appear on the TV screen.
6 Press REC/OTR once
7 Press STOP to stop recording.
You are now recording the program you see and hear on the
TV.
1-75
OPERATION
VHS Hi-Fi Stereo System/
MTS Broadcast
Operation with tape (Continued)
Tape Counter Memory Feature
Additional Information
Real-Time Counter
z
In manual recording, Timer recording, One-touch Timer
Recording, playback, or fast forward modes, the DVD+VCR
automatically starts rewinding the tape at the end of the
tape. The cassette will stop at the beginning of the tape and
be ejected, and the DVD+VCR will turn itself off.
z
After you have finished using the DVD+VCR, rewind, eject,
and remove the cassette. Place the cassette in its protective sleeve to protect it from dust. It is not necessary to
rewind the cassette before removing it, but if you do, it will
be ready to play or record the next time you use it.
z
Be sure the DVD+VCR Channel Selector is on the correct
channel you wish to record. The channel that is being
recorded can always be checked by setting the television
on the DVD+VCR channel (3 or 4) and pressing the
TV/VCR selector to turn the DVD+VCR’s VCR indicator on.
z
Do not attempt to hook up more than one television set to
the DVD+VCR for either recording or playback.
Shows length of tape run in hours, minutes, and seconds. Press CLK/CNT to select the real-time counter
display.
Every press of CLK/CNT changes the TV screen as
illustrated below.
2:15 AM
CLOCK
z
z
z
0:05:25
COUNTER
REM 1:07
REMAINING TIME
Counter changes to “0:00:00” when the cassette is
ejected.
The real-time counter does not operate if nothing is recorded on the tape.
The real-time counter will not work unless a tape is
inserted.
S-VHS Quasi Playback (SQPB)
Counter Memory Function
This is useful if there is a section of tape you want to
view immediately after recording or if you want to return
to the same point several times.
1
CLK/CNT repeatedly to display the real2 Press
time counter appears on the TV screen.
the point that you want locate later, reset the
3 Atreal-time
counter to “0:00:00” by pressing
COUNTER RESET.
z
This DVD+VCR can also play back a tape which is recorded in S-VHS playback picture.
z
This DVD+VCR cannot record in S-VHS format
z
SQPB is an abbreviation for S-VHS Quasi Playback.
Begin recording or playing a tape.
Auto Play System
This DVD+VCR features automatic playback.
Load a cassette (with the safety tab removed).
4
STOP when recording or playback finish5 Press
es.
REW.
6 Press
The tape automatically stops when the tape counter
returns to about “0:00:00”.
Continue to play or record.
Tape Remaining
This function allows the time of the remaining tape to be
displayed during recording or playback.
Press CLK/CNT until the REM indicator displays on the
TV screen during recording or playback.
z
The Output Source is changed to VCR mode automattically.
z
The power turns on automatically and playback begins.
z
At the end of the tape, the DVD+VCR stops, then rewinds.
z
The cassette is ejected after rewinding and goto standby.
LOAD
AUTO
REWIND
TAPE
EJECT
Video Head Cleaning
z
Whenever a video cassette is inserted into or ejected from
this unit the video head is automatically cleaned.
z
However, it is possible that the heads may become clogged
when playing an old or damaged tape. If the image on your
screen resembles the picture on the left while playing back
a tape, the heads may require cleaning.
z
To clean the heads, obtain a head cleaning tape from your
local video dealer. Follows the instructions that come with
the cleaning tape, as excessive use can shorten head life.
Note
The remaining tape length indicator may not be displayed
correctly depending on the condition of the tape and the kind of
the tape (T-140, T-160, or T-210 etc)
AUTO
AUTO
PLAY
Blank Search
The Blank Search enables you to locate the end of any
recording. Whenever a recording creates, a blank content is recorded on the tape.
Press BLANK SEARCH during playback or in the stop
mode and rapidly advanced to find blank content.
To find next blank content, press BLANK SEARCH
again.
1-76
Operation with DVD and Video CD
Playback Setup
z
z
z
DVD
VCD2.0
General Features
VCD1.1
Turn on the TV and select the video input source connected to the DVD+VCR.
Audio system: Turn on the audio system and select
the input source connected to the DVD+VCR.
Set the Output Source to DVD as shown in Setting
the Output Source on page 6.
1
your chosen disc in the tray, with the label
2 Load
facing up.
When a double-sided DVD is inserted, make sure
Press OPEN/CLOSE to open the disc tray.
the side you want to play is facing down.
OPEN/CLOSE to close the tray.
3 Press
“dISC LOAD” appears in the display window, and
playback starts automatically.
If a menu screen is displayed
The menu screen may be displayed first after loading a
DVD or Video CD that contains a menu.
DVD
Use b/B/v/V buttons to select the title/chapter you
want to view, then press ENTER to start playback.
Press TOP MENU or MENU to return to the menu
screen.
VCD2.0
z
z
z
z
z
DVD
1/3
When a disc has more than one title, you can move to
another title as follows:
z Press DISPLAY when playback is stopped, then
press the appropriate numbered button (0-9) then
press ENTER to select a title number.
Moving to another CHAPTER/TRACK
VCD1.1
1/12
1/3
When a title on a disc has more than one chapter or a
disc has more than one track, you can move to another
chapter/track as follows:
z Press SKIP (
) or SKIP (
) briefly during playback to return to the beginning of the current
chapter/track or to select the next chapter/track.
z Press SKIP (
) twice in quick successions to step
back to the previous chapter/track.
z To go directly to any chapter/track during playback,
press DISPLAY. Then, press v/V to select C
(chapter) (or for a Video CD, select T for track). Then,
enter the chapter number using the numbered buttons
(0-9).
z For two-digit numbers, press the buttons in rapid succession.
.
.
Slow Motion
Use the number buttons to select the track you want
to view.
Press RETURN to return to the disc menu screen.
Menu setting and the exact operating procedures for
using the disc menu may differ depending on the disc.
Follow the instructions on each menu screen.
You also may set PBC to Off under setup. See page
20.
Notes
If Parental Control is set and the disc is not within the
Rating settings (not authorized), the 4-digit password
must be entered and/or the disc must be authorized
(see Parental Control, on page 21).
DVDs may have a region code.
Your DVD+VCR will not play discs that have a region
code different from your DVD+VCR. The region code
for this DVD+VCR is 1 (one).
Do not keep an image or on-screen displayed for a
long time.
Moving to another TITLE
DVD
If playback does not start, press PLAY.
In some cases, the disc menu might appear
instead.
For some VCD discs, it might take 5 or 6 secs after
pressing PLAY before the playback picture appears.
z
Note
Unless stated otherwise, all operations described use
the remote control. Some features may also be
available on the Setup menu.
>
DVD
VCD2.0
VCD1.1
. >
. >
t t t t
1 Press PAUSE/STEP during playback.
The DVD+VCR will now go into PAUSE mode.
2 Press SKIP (
) or SKIP (
) during pause mode.
The DVD+VCR will enter SLOW mode.
3 Use SKIP (
) or SKIP (
) to select the required
speed:
1/16,
1/8,
1/4 or
1/2 (backward),
or
1/16,
1/8,
1/4 or
1/2 (forward).
4 To return to playback, press PLAY.
T
T T
T
Note
Slow motion playback in reverse is not available from a
Video CD.
1-77
OPERATION
Playing DVD and Video CD
Operation with DVD and Video CD (Continued)
General Features (continued)
Still Picture and Frame-by-frame playback
DVD
VCD2.0
VCD1.1
1 Press PAUSE/STEP during playback.
The DVD+VCR will now go into PAUSE mode.
2 With a DVD, you can advance the picture frame by
frame by pressing PAUSE/STEP repeatedly on the
remote control.
3 To return to playback, press PLAY.
Time Search
DVD
0:16:57
-:--:--
The Time Search function allows you to start playing at
any chosen time on the disc.
1 Press DISPLAY during playback. The on-screen display appears on the screen.
The Time Search box shows the elapsed playing time of the
current disc.
2 Within 10 seconds, use v/V to select the Time
Search icon in the on-screen display.
The “-:--:--” appears in the Time Search box.
Search
DVD
VCD2.0
VCD1.1
1 Press REW or FWD for about two seconds during
playback.
3 Within 10 seconds, use the numbered buttons to
enter the required start time. Enter hours, minutes
and seconds from left to right in the box.
If you enter the wrong numbers, press CLEAR to remove the
numbers you entered. Then enter the correct numbers.
The DVD+VCR will now go into SEARCH mode.
M mM mM m M m
M M
Mm m m
2 Press REW or FWD repeatedly to select the required
speed:
X2,
X4,
X16,
X100 (backward)
or
X2,
X4,
X16,
X100 (forward).
With a Video CD, the Search speed changes:
X2,
X4,
X8 (backward) or
X2,
X4,
X8 (forward).
3 To return to playback, press PLAY.
Random
Karaoke DVD
VCD1.1
1 Press RANDOM during playback or in stop mode.
The unit automatically begins Random Playback and
“RANDOM” appears on the TV screen.
2 To return to normal playback, press RANDOM until
“NORMAL” appears on the TV screen.
.
>
Tips
By pressing SKIP (
) or SKIP (
) during Random
playback, the unit selects another title (track) and
resumes Random playback.
Note
This function only works with DVD Karaoke discs and
video CD without PBC.
4 Within 10 seconds, press ENTER.
Playback starts from the selected time on the disc. If you enter
an invalid time, playback will continue from the current point.
Selecting the sound enhancement
DVD
VCD2.0
VCD1.1
NORM.
3D SUR
DIALOGUE
1 Press DISPLAY during playback.
2 Use
v/V to select the sound icon.
The sound option will be highlighted.
3 Use b/B to select “NORM”, “3D SUR” or
“DIALOGUE”.
NORM. : Normal sound
3D SUR: This player can produce a 3D Surround effect, which
simulates multi-channel audio playback from two conventional stereo speakers, instead of the five or more speakers normally required to listen to multi-channel audio from a home
theater system.
DIALOGUE: Enhances critical center channel information to
make dialogue more intelligible (only when playing a DVD
video disc recorded on the Dolby Digital recording system).
• To use this enhancement on audio output from the
DIGITAL AUDIO OUT jack, be sure to set “Digital Audio
Output” to “PCM”. See page 20.
1-78
Operation with DVD and Video CD (Continued)
CHAPT
DVD
TITLE
VCD2.0
TRACK
Zoom
VCD1.1
ALL
If you press ZOOM repeatedly, the magnification level
increases up to six steps.
The Repeat Chapter icon appears on the TV screen.
2 Use b/B/v/V buttons to move through the zoomed
picture.
The Repeat Title icon appears on the TV screen.
3 To exit Repeat mode, press REPEAT a third time.
3 Press CLEAR to resume normal playback or return to
the paused image.
The Repeat Off icon appears on the TV screen.
Video CDs - Repeat Track/All/Off
1 To repeat the track currently playing, press REPEAT.
z
The Repeat Track icon appears on the TV screen.
z
2 To repeat the disc currently playing, press REPEAT
two times.
The Repeat All icon appears on the TV screen.
1/9
Note
On a Video CD with PBC, you must set PBC to Off on
the setup menu to use the Repeat function.
See page 20.
If you press SKIP (
) twice or SKIP (
) during
Repeat Chapter/Track playback, the repeat playback
cancels.
Repeat A-B
A
*
DVD
>
VCD2.0
Note
The zoom function may not work for some DVDs.
The zoom function may not work on multi-angle
scenes.
Marker Search
3 To cancel Repeat mode, press REPEAT repeatedly until
the Repeat Off icon appears on the TV screen.
.
VCD1.1
1 Press ZOOM during playback or still playback to activate the Zoom function.
2 To repeat the title currently playing, press REPEAT a
second time.
z
VCD2.0
The Zoom function allows you to enlarge the video
image and to move through the enlarged image.
OFF
DVD Video Discs - Repeat Chapter/Title/Off
1 To repeat the currently playing chapter, press
REPEAT.
z
DVD
DVD
VCD2.0
VCD1.1
MARKER SEARCH
You can start playback from a memorized point. Up to
nine points can be memorized.
To enter a mark, follow these steps.
1 During disc playback, press MARKER when playback
reaches the spot that you want to memorize.
The Marker icon will appear on the TV screen briefly.
2 Repeat step 1 to enter up to nine Marker points on a
disc.
VCD1.1
To Recall a Marked Scene
A
B
OFF
1 During disc playback, press SEARCH.
To repeat a sequence in a title:
1 Press A-B at your chosen starting point.
A- appears briefly on the TV screen.
2 Press A-B again at your chosen end point.
A-B appears briefly on the TV screen, and the repeat
sequence begins
3 To cancel the sequence, press A-B.
The Marker Search menu will appear on the screen.
2 Within 10 seconds, press b/B to select a Marker
number that you want to recall.
3 Press ENTER.
Playback will start from the Marked scene.
4 To remove the MARKER SEARCH menu, press
SEARCH.
To clear a Marked Scene
1 During disc playback, press SEARCH.
The Marker Search menu will appear on the screen.
2 Within 10 seconds, press b/B to select a Marker
number that you want to erase.
3 Press CLEAR.
The Marker number will be erased from the list.
4 Repeat steps 2 and 3 to erase additional Marker
numbers.
5 To remove the MARKER SEARCH menu, press
SEARCH.
1-79
OPERATION
Repeat
Operation with DVD and Video CD (Continued)
Special DVD Features
Subtitles
DVDs may contain menus that allow you to access special features. To use the disc menu, press MENU. Then,
press the appropriate number button to select an option.
Or, use b/B/v/V buttons to highlight your selection,
then press ENTER.
If
DVD
1 Press TOP MENU.
If the current title has a menu, the menu will appear on the
screen. Otherwise, the disc menu may appear.
2 The menu can list camera angles, spoken language
and subtitle options, and chapters for the title.
3 To remove the title menu, press TOP MENU again.
Disc Menu
DVD
1 Press MENU.
The disc menu is displayed.
2 To remove the disc menu, press MENU again.
Camera Angle
DVD
1/1
If the disc contains sequences recorded from different
camera angles, the angle icon blinks on the TV screen.
You can then change the camera angle if you wish.
z Press ANGLE repeatedly during playback to select a
desired angle.
The number of the current angle appears on the display.
Changing the Audio Language
DVD
1 ENG
D
5.1 CH
Press AUDIO repeatedly during playback to hear a
different audio language or audio track.
Changing the Audio Channel
VCD2.0
VCD1.1
STER.
LEFT
1 ENG
Press SUBTITLE repeatedly during playback to see the
different subtitle languages.
Checking the contents of DVD Video
discs: Menus
Title Menu
DVD
RIGHT
Press AUDIO repeatedly during playback to hear a different audio channel (STEREO, LEFT or RIGHT).
1-80
Note
appears, the feature is not available on the disc.
Operation with Audio CD
Playing an Audio CD
1 Press and hold REW or FWD for about two seconds
during playback.
Insert a disc and close the tray.
The menu appears on the TV screen.
CD
The player will now go into SEARCH mode.
M
M mM m m
2 Press REW or FWD repeatedly to select the required
speed:
X2,
X4,
X8 (backward) or
X2,
X4,
X8 (forward).
3 Search speed and direction are indicated on the
menu screen.
Program
TRACK 1
TRACK 2
TRACK 3
TRACK 4
TRACK 5
TRACK 6
TRACK 7
Clear All
TRACK 8
0:56:35
CD
STER.
4 To exit SEARCH mode, press PLAY.
NORM.
Audio CD menu
2
Press v/V to select a track then press PLAY.
Playback starts.
During playback, the current track’s elapsed playing
time will appear on the display window.
Playback will stop at the end of the disc.
3 To stop playback at any other time, press STOP.
Pause
Random
CD
1 Press RANDOM during playback or when playback is
stopped.
The unit automatically begins Random Playback and
“RAND.” appears on the menu screen.
2 To return to normal playback, press RANDOM repeatedly until “RAND.” disappears on the menu screen.
Repeat A-B
CD
1 Press PAUSE/STEP during playback.
2 To return to playback, press PLAY or press
PAUSE/STEP again.
>
.
.
Moving to another Track
To repeat a sequence.
1 During disc playback, press A-B at your chosen starting point.
The Repeat icon and “A -” appears on the menu screen.
2 Press A-B again at your chosen end point.
CD
The Repeat icon and “A B” appears on the menu screen,
and the sequence begins to play repeatedly.
z
Press SKIP (
) or SKIP (
) briefly during
playback to go to the next track or to return to the
beginning of the current track.
z
Press SKIP (
) twice in quick successions to step
back to the previous track.
z
To go directly to any track, enter the track number
using the numbered buttons (0-9) during playback.
3 To exit the sequence and return to normal play, press
A-B again.
The Repeat icon and “OFF” appear on the menu screen.
Selecting the sound enhancement
CD
1 Press DISPLAY during playback.
2 Use
Repeat Track/All/Off
CD
b/B to select the sound icon.
The sound option will be highlighted.
CD
1 To repeat the track currently playing, press REPEAT.
The Repeat Track icon appears on the menu screen.
2 To repeat all tracks on a disc, press REPEAT a second time.
The Repeat All icon appears on the menu screen.
3 To cancel Repeat mode, press REPEAT a third time.
3 Use
v/V to select “NORM.” or “3D SUR”.
NORM. : Normal sound
3D SUR: This player can produce a 3D Surround effect, which
simulates multi-channel audio playback from two conventional stereo speakers, instead of the five or more speakers normally required to listen to multi-channel audio from a home
theater system.
The Repeat Off icon appears on the menu screen.
Changing the Audio Channel
Press AUDIO repeatedly during playback to hear a different audio channel (STER., LEFT, or RIGHT).
Note
The REPEAT button is not available when the
appears.
Press PROGRAM to disappear the
CD
E
E
mark
mark.
1-81
OPERATION
1
Search
Operation with MP3 Disc
Playing an MP3 disc
MP3
z
The DVD Player can play MP3 formatted recordings on
CD-ROM, CD-R or CD-RW discs.
Before playing MP3 recordings, read the notes on MP3
Recordings on right.
1
z
Insert a disc and close the tray.
The MP3/JPEG/WMA choice menu appears on the
TV screen.
z
z
WMA
Press v/V to select the MP3 then press ENTER.
2 The
MP3 menu appears on the TV screen.
z
Program
TRACK 2.MP3
TRACK 3.MP3
TRACK 4.MP3
1.
2.
3.
4.
TRACK 5.MP3
TRACK 6.MP3
TRACK 7.MP3
Clear All
1
OFF
MP3 menu
3
Press v/V to select a track then press PLAY.
Playback starts.
During playback, the current track’s elapsed playing
time will appear on the display.
Playback will stop at the end of the disc.
Press TOP MENU to move to the next page.
Press MENU to move to the previous page.
4 To stop playback at any other time, press STOP.
Pause
MP3
1 Press PAUSE/STEP during playback.
2 To return to playback, press PLAY or press
PAUSE/STEP again.
>
.
.
Moving to another Track
MP3
z
Press SKIP (
) or SKIP (
) briefly during playback to advance to the next track or to return to the
beginning of the current track.
z
Press SKIP (
) twice in quick successions to step
back to the previous track.
Repeat Track/All/Off
An MP3 file is audio data compressed by using the
MPEG1 audio layer-3 file-coding scheme. We call
files that have the “.mp3” file extension “MP3 files”.
The player cannot read an MP3 file that has a file
extension other than “.mp3”.
The player cannot read a non MP3 encoded file that
has a file extension “.mp3”.
MP3 Disc compatibility with this player is limited as follows:
TRACK 1.MP3
56:35
>
About MP3
JPEG
TRACK 8.MP3
.
Notes on MP3 Discs
MP3
MP3
Note
The REPEAT button is not available when the E
mark appear. Press PROGRAM to clear the E mark.
If you press SKIP (
) twice or SKIP (
) during
Repeat Track playback, the repeat playback cancels.
MP3
1 To repeat the track currently playing, press REPEAT.
The Repeat Track icon appears on the menu screen.
2 To repeat all tracks on a disc, press REPEAT two
times.
The Repeat All icon appears on the menu screen.
3 To cancel Repeat mode, press REPEAT repeatedly until
the Repeat Off icon appears on the menu screen.
Sampling Frequency / only at 44.1kHz
Bit rate / within 32 - 320kbps
CD-R physical format should be “ISO 9660”
If you record MP3 files using the software which
cannot create a FILE SYSTEM, for example “DirectCD” etc., it is impossible to playback MP3 files. We
recommend that you use “Easy-CD Creator”, which
creates an ISO9660 file system.
5. A single session disc requires MP3 files in the first
track. If there is no MP3 file in the 1st track, it cannot playback MP3 files. If you wish to playback MP3
files, format all the data in the disc or use a new
one.
6. We do not recommend using CD-RW discs. Please
use finished CD-R discs only.
7. File names should be named using 8 letters or less
and must incorporate “.mp3” extension
e.g. “********.MP3”.
8. Do not use special letters such as “_?!><+*}{`[@
]:;\/.,” etc.
9. Total number of files on the disc should be less than
200.
10. Use 74 minute CD-R discs (650M), Do not use 80
minute CD-R (700M) software
This DVD player requires discs/recordings to meet
certain technical standards in order to achieve optimal
playback quality. Pre-recorded DVDs are automatically
set to these standards. There are many different types
of recordable disc formats (including CD-R containing
MP3 files). That require certain pre-existing conditions
(see above) to insure compatible playback.
Customers should also note that permission is
required in order to download MP3 files and music
from the Internet. TOSHIBA cannot grant such
permission. Permission should always be sought
from the copyright owner.
1-82
Operation with JPEG Disc
.
>
Moving to another File
JPEG
z
This DVD Player can play discs with JPEG files on it.
Make sure the resolution of the JPEG files is less than
2 mega pixels (2M).
Press SKIP (
) or SKIP (
) once during viewing
to advance to the next file or to the previous file.
Repeat All/Off
z
z
z
Notes
Depending upon the size and number of the JPEG
files, it could take a long time for the DVD player to
read the disc’s contents. If you don’t see an onscreen display after several minutes, some of the files
are too big — reduce the resolution of the JPEG files
to less than 2 mega pixels and burn another disc.
Total number of files on the disc should be less than
200.
1 To repeat all files on a disc, press REPEAT when
JPEG menu appears.
The Repeat All icon appears on the menu screen.
2 Press PLAY or ENTER to start repeat playback.
3 To cancel Repeat mode, first press STOP to stop
playback then press REPEAT when JPEG menu
appears.
The Repeat Off icon appears on the menu screen.
Some discs/files may be incompatible due to different
recording format or condition of discs/files.
Note
The REPEAT button is not available when the E mark
appear. Press PROGRAM to clear the E mark.
1
1 Insert a disc and close the tray.
The MP3/JPEG/WMA choice menu appears on the
TV screen.
Notes on JPEG Files
MP3
JPEG
z
When you are using software such as “Easy CD
Creator” to burn the jpeg files into the CD-R, ensure
that all the selected files have the “.jpg” extensions
when copying into the CD layout.
z
If the files have “.jpe” or “.jpeg” extensions, please
rename them as “.jpg” files.
z
File names without “.jpg” extension will not be able to
be read by this DVD+VCR. Even though the files are
shown as JPEG image files in windows explorer.
WMA
Press v/V to select the JPEG then press
2 ENTER.
The JPEG menu appears on the TV screen.
Press RETURN to move to the previous menu
(MP3/JPEG/WMA choice menu).
JPEG
Program
Picture1.jpg
Picture2.jpg
Picture3.jpg
Picture4.jpg
Picture5.jpg
Picture6.jpg
Picture7.jpg
Clear All
Picture8.jpg
1/31
OFF
Slide Speed
Fast
JPEG menu
If you want to view a particular file, press v/V to
3 highlight
a file and press ENTER or PLAY.
Viewing the file proceeding starts.
During viewing a file, press DISPLAY or RETURN
to move to the previous menu (JPEG menu).
Press TOP MENU to move to the next page.
Press MENU to move to the previous page.
Tip
There are three viewing Slide Speed options: Fast,
Normal, and Slow. Press b/B to highlight the Slide
Speed then press v/V to select the option you want to
use, and press ENTER.
viewing at any other time, press STOP.
4 ToThestop
JPEG menu appears.
1-83
OPERATION
Viewing a JPEG disc
Operation with WMA Disc
Playing an WMA disc
WMA
The DVD Player can play WMA formatted recordings on
CD-ROM, CD-R or CD-RW discs.
z
1
z
Insert a disc and close the tray.
The MP3/JPEG/WMA choice menu appears on the
TV screen.
WMA
v/V to select the WMA then press ENTER.
2 Press
The WMA menu appears on the TV screen.
Program
TRACK 1.WMA
TRACK 2.WMA
TRACK 3.WMA
TRACK 4.WMA
TRACK 5.WMA
TRACK 6.WMA
TRACK 7.WMA
56:35
Clear All
1
OFF
WMA menu
v/V to select a track then press PLAY.
3 Press
Playback starts.
During playback, the current track’s elapsed playing
time will appear on the display.
Playback will stop at the end of the disc.
Press TOP MENU to move to the next page.
Press MENU to move to the previous page.
4 To stop playback at any other time, press STOP.
Pause
WMA
1 Press PAUSE/STEP during playback.
2 To return to playback, press PLAY or press
PAUSE/STEP again.
>
.
.
Moving to another Track
WMA
z
Press SKIP (
) or SKIP (
) briefly during playback to advance to the next track or to return to the
beginning of the current track.
z
Press SKIP (
) twice in quick successions to step
back to the previous track.
Repeat Track/All/Off
>
1. Sampling Frequency / within 32 - 44kHz
2. Bit rate / within 48 - 80kbps
JPEG
TRACK 8.WMA
.
WMA Disc compatibility with this player is limited as follows:
MP3
WMA
Note
The REPEAT button is not available when the E
mark appear. Press PROGRAM to clear the E mark.
If you press SKIP (
) twice or SKIP (
) during
Repeat Track playback, the repeat playback will be
canceled.
WMA
1 To repeat the track currently playing, press REPEAT.
The Repeat Track icon appears on the menu screen.
2 To repeat all tracks on a disc, press REPEAT two
times.
The Repeat All icon appears on the menu screen.
3 To cancel Repeat mode, press REPEAT repeatedly until
the Repeat Off icon appears on the menu screen.
1-84
CD
MP3
JPEG
WMA
VCD2.0
VCD1.1
Programmed Playback with
Audio CD, MP3, JPEG or WMA
Disc CD MP3 JPEG WMA
Programmed Playback with
Video CD VCD2.0 VCD1.1
Program allows you to store your favorite tracks/files
(or files) for a particular disc in the player memory.
Program can contain 32 tracks (Audio CD/Video CD) or
60 tracks (MP3/JPEG/WMA disc).
Note
On a Video CD with PBC, you must set PBC to Off on the
setup menu to use the Program function. See page 20.
1
2
Insert a disc and close the tray.
• The Audio CD menu appears.
• If MP3, JPEG or WMA disc is inserted, the
MP3/JPEG/WMA choice menu appears on the TV
screen.
Press v/V to select the MP3, JPEG or WMA then
press ENTER. The MP3, JPEG or WMA menu
appears on the TV screen. Press RETURN to
move to the previous menu (MP3/JPEG/WMA
choice menu).
Press PROGRAM in the stop mode or during
playback (Audio CD, MP3 and WMA only) to
enter the Program Edit mode.
TRACK 12
TRACK 2
TRACK 8
TRACK 3
TRACK 10
TRACK 4
TRACK 3
TRACK 3
TRACK 4
TRACK 5
TRACK 6
TRACK 7
TRACK 8
E
TRACK 6
TRACK 7
0:56:35
Clear All
B.
STER.
NORM.
For example: Audio CD menu
5
Press v/V to select the track/file you want to
6 start
playing.
Press
The programmed track/file you selected last is highlighted
on the program list.
7
Clear All
Press and hold PROGRAM for 3 seconds until “PROG.”
indicator disappears in the display window.
TRACK 5
TRACK 8
E
TRACK 2
To resume normal playback from programmed
playback
step 3 to place additional tracks/files on
4 Repeat
the Program list.
Program
Program
TRACK 1
Tip
Press v/V to select a track/file then press
ENTER to place the selected track/file on the
Program list.
TRACK 1
VCD
steps 3-7 of “Programmed Playback with
3 Follow
Audio CD, MP3, JPEG or WMA Disc” on left.
Note
Press PROGRAM to exit the Program Edit mode;
the E mark will disappear.
CD
The VCD Program menu will appear.
Note
Press RETURN or PROGRAM to exit the Program menu.
The E mark will appear to the right of the word Program
on the right side of the menu screen.
3
1 Insert Video CD and close the tray.
2 Press PROGRAM while playback is stopped.
Press TOP MENU to move to the next page.
Press MENU to move to the previous page.
Press ENTER or PLAY to start.
Playback begins in the order in which you programmed the
tracks/files and “PROG.” appears in the display window.
Playback stops after playing the last programmed track/file
on the program list.
Note
The programmed tracks/files are cleared when the
power is turned off or the disc is removed.
1-85
OPERATION
Programmed Playback
Programmed Playback (Continued)
Repeat Programmed Tracks/All/Off
CD
MP3
WMA
1 To repeat the track currently playing, press REPEAT.
The Repeat Track icon appears on the menu screen.
2 To repeat all tracks on the program list, press
REPEAT two times.
The Repeat All icon appears on the menu screen.
3 To cancel Repeat mode, press REPEAT repeatedly
until the Repeat Off icon appears on the menu
screen.
.
>
Note
If you press SKIP (
) twice or SKIP (
) during
Repeat Track playback, the repeat playback cancels.
Repeat Programmed All/Off
JPEG
1 To repeat all files on the program list, press REPEAT
when JPEG menu appears.
The Repeat All icon appears on the menu screen.
2 Press PLAY or ENTER to start repeat playback.
3 To cancel Repeat mode, first press STOP to stop
playback then press REPEAT when JPEG menu
appears.
Note
The REPEAT button is not available when the E mark
appear. Press PROGRAM to clear the E mark.
Erasing a Track/File from Program List
1 Press PROGRAM during playback or in the stop
mode to enter the Program Edit mode.
The
E
mark will appear.
Note
JPEG can be programmed only in stop mode (when
menu screen is displayed.)
2 Press B to move to the Program list.
3 Use v/V to select the track/file that you wish to erase
from the Program list.
4 Press CLEAR.
The track/file will be erased from the Program list.
Erasing the Complete Program List
1 Follow steps 1-2 of “Erasing a Track/File from
Program List” as above.
2 Use v/V to select “Clear All”, then press ENTER.
The complete Program for the disc will be erased.
The programs are also cleared when the disc is removed.
1-86
Additional Information - DVD Part
Press INSTANT REPLAY during playback and the disc
will reverse picture search through 10 seconds of playback. And then the playback will start from the point
again.
Screen Saver
A screen saver image appears when you leave the DVD
Player in stop mode for about five minutes.
Video Mode Setting
DVD
VCD2.0
VCD1.1
z
With certain discs, the playback picture may be flickering or Dot Crawl is shown on straight lines. That
means Vertical interpolation or De-interlace is not
perfectly matched with the disc. In this case, the
picture quality may be improved by changing the
video mode.
z
To change the video mode, press and hold DISPLAY
about 3 seconds during disc playback. The new video
mode number selected is displayed on the TV screen.
Check whether the video quality has improved. If not,
repeat the above procedure until picture quality is
improved.
z
Video mode sequence:
Video1 → Video2 → Film → Adapt → Auto.
If you turn off the power, the video mode will return to
initial default state (Auto).
z
Detailed Description of each Video Mode
Auto : The source material of the DVD video (film material or
video material) is determined from disc information.
Video1 : Suitable for playing video based content with
comparatively little motion.
Video2 : Suitable for playing video based content with
comparatively more motion.
Film : Suitable for playing film based content or video based
material recorded by the progressive scan method.
Adapt : Determines the appropriate mode (film or video)
during disc playback, and automatically selects the proper
mode. Suitable for playing a disc comprised of film and
video based content.
1-87
OPERATION
One Touch Replay
Troubleshooting
Check the following guide for the possible cause of a problem before contacting service.
Cause
Symptom
Correction
No power.
z
The power cord is disconnected.
z
Plug the power cord into the wall outlet
securely.
The power is on, but
the DVD+VCR does not
work.
z
No disc is inserted.
No tape is inserted.
z
Insert a disc or tape. (Check that the
disc or tape indicator in the display
window is lit.)
No picture.
z
The TV is not set to receive DVD+VCR
signal output.
z
Select the appropriate video input mode
on the TV so the picture from the
DVD+VCR appears on the TV screen.
z
TV/VCR mode for DVD+VCR is set to
TV.
z
Press the TV/VCR button on the remote
control repeatedly to choose VCR
mode. TV indicator disappears in the
display window.
z
The video cable is not connected
securely.
z
Connect the video cable securely.
z
The connected TV power is turned off.
z
Turn on the TV.
z
The equipment connected with the
audio cable is not set to receive
DVD+VCR signal output.
z
Select the correct input mode of the
audio receiver so you can listen to the
sound from the DVD+VCR.
z
The audio cables are not connected
securely.
z
Connect the audio cable securely.
z
The power of the equipment connected
with the audio cable is turned off.
z
Turn on the equipment connected with
the audio cable.
z
The Digital Audio Output is set to the
wrong position.
z
Set the Digital Audio Output to the
correct position, then turn on the
DVD+VCR again by pressing POWER.
z
The disc is dirty.
z
Clean the disc.
z
Tape heads are dirty.
z
Clean video heads.
z
Tape is a rental or was recorded on
another VCR.
z
Use CH/TRK (+/-) for manual tracking
adjustment while tape is playing.
z
No disc is inserted.
No tape is inserted.
z
z
Insert a disc or tape. (Check that the
disc or tape indicator in the display
window is lit.)
z
An unplayable disc is inserted.
z
Insert a playable disc. (Check the disc
type, color system, and Regional code.)
z
The disc is placed upside down.
z
Place the disc with the playback side down.
z
The disc is not placed within the guide.
z
Place the disc on the disc tray correctly
inside the guide.
z
The disc is dirty.
z
Clean the disc.
z
The Rating level is set.
z
Cancel the Rating function or change
the rating level.
z
The remote control is not pointed at the
remote sensor of the DVD+VCR.
z
Point the remote control at the remote
sensor of the DVD+VCR.
z
The remote control is too far from the
DVD+VCR.
z
Operate the remote control within 23 ft
(7 m).
z
There is an obstacle in the path of the
remote control and the DVD+VCR.
z
Remove the obstacle.
z
The batteries in the remote control are
exhausted.
z
Replace the batteries with new ones.
z
This remote control use the same
buttons for VCR and DVD functions
(ex. PLAY).
z
When using a VCR, first press the VCR
button. When using a DVD, first press
the DVD button.
No sound.
The playback picture is
poor.
The DVD+VCR does
not start playback.
The remote control
does not work properly.
z
1-88
Troubleshooting (Continued)
Cause
Correction
Some channels are
skipped over when
using CH/TRK (+/-)
z
Those channels were deleted with the
CH. ADD/DEL option.
z
Use CH. ADD/DEL. to restore channels.
See “Channel Selection” on page 16.
Picture and sound of
broadcasting channel
are weak or missing.
z
Antenna or cables are loose.
z
Tighten connections or replace cable.
z
Wrong TUNING BAND option is being
used.
z
Try all TUNING BAND options. See
“Channel Selection” on page 16 for
details.
Camcorder image is not
shown.
z
Camcorder is off.
z
Turn camcorder on and operate
properly.
Camcorder image via
A/V input to DVD+VCR
is not shown on TV
screen.
z
DVD+VCR SOURCE SELECT is not set
to LINE1 or LINE2.
z
Press INPUT SELECT to select LINE
input channel (LINE1 or LINE2).
Timer recording is not
possible.
z
Clock in DVD+VCR is not set to correct
time.
z
Set clock to correct time. See “Setting
the Clock” on page 17.
z
Timer has been programmed
incorrectly.
z
Reprogram Timer. See “Timer
Recording” on page 24.
z
TIMER indicator does not appear after
programming timer.
z
Reprogram Timer
z
DVD+VCR is in Timer Recording mode.
z
This is the normal indication that the
DVD+VCR is in TIMER mode.
z
TV is not Stereo-compatible.
z
No action is possible.
z
Broadcast program is not in stereo format.
z
No action is possible.
z
DVD+VCR A/V Out jacks are not connected to TV A/V In jacks.
z
Make A/V connections. Stereo is
available only via A/V output from
DVD+VCR.
z
DVD+VCR Audio/Video Out is not
selected for viewing at the TV.
z
Select AUX or A/V source as TV input.
z
DVD+VCR BROADCAST TYPE mode is
set to SAP or MONO.
z
Set BROADCAST TYPE mode to
STEREO. See “Setting the VCR Setup
Menu” on page 16.
TIMER indicator
appears after DVD+VCR
is turned off.
Stereo Audio Record
and/or Playback is not
present.
Moisture Condensation
Moisture condensation can occur:
In locations where moisture condensation may occur:
• When the DVD+VCR is moved from a cold place to a
warm place.
• Keep the DVD+VCR plugged into an AC power outlet
with POWER On. This will help prevent condensation.
• Under extremely humid conditions.
• When condensation has occurred, wait a few hours
for the DVD+VCR to dry before using it.
1-89
OPERATION
Symptom
Language Code List
Enter the appropriate code number for the initial settings “Disc Audio”, “Disc Subtitle” and/or “Disc Menu”
(See page 19).
Code
Language
Code
Language
Code
Language
Code
Language
6566
Abkhazian
7074
Fiji
7678
Lingala
8373
Singhalese
6565
Afar
7073
Finnish
7684
Lithuanian
8375
Slovak
6570
Afrikaans
7082
French
7775
Macedonian
8376
Slovenian
8381
Albanian
7089
Frisian
7771
Malagasy
8379
Somali
6577
Amharic
7176
Galician
7783
Malay
6983
Spanish
6582
Arabic
7565
Georgian
7776
Malayalam
8385
Sudanese
7289
Armenian
6869
German
7784
Maltese
8387
Swahili
6583
Assamese
6976
Greek
7773
Maori
8386
Swedish
6588
Aymara
7576
Greenlandic
7782
Marathi
8476
Tagalog
6590
Azerbaijani
7178
Guarani
7779
Moldavian
8471
Tajik
6665
Bashkir
7185
Gujarati
7778
Mongolian
8465
Tamil
6985
Basque
7265
Hausa
7865
Nauru
8484
Tatar
6678
Bengali; Bangla
7387
Hebrew
7869
Nepali
8469
Telugu
6890
Bhutani
7273
Hindi
7879
Norwegian
8472
Thai
6672
Bihari
7285
Hungarian
7982
Oriya
6679
Tibetan
6682
Breton
7383
Icelandic
8065
Panjabi
8473
Tigrinya
6671
Bulgarian
7378
Indonesian
8083
Pashto, Pushto
8479
Tonga
7789
Burmese
7365
Interlingua
7065
Persian
8482
Turkish
6669
Byelorussian
7165
Irish
8076
Polish
8475
Turkmen
7577
Cambodian
7384
Italian
8084
Portuguese
8487
Twi
6765
Catalan
7465
Japanese
8185
Quechua
8575
Ukrainian
9072
Chinese
7487
Javanese
8277
Rhaeto-Romance
8582
Urdu
6779
Corsican
7578
Kannada
8279
Romanian
8590
Uzbek
7282
Croatian
7583
Kashmiri
8285
Russian
8673
Vietnamese
6783
Czech
7575
Kazakh
8377
Samoan
8679
Volapük
6865
Danish
7589
Kirghiz
8365
Sanskrit
6789
Welsh
7876
Dutch
7579
Korean
7168
Scots Gaelic
8779
Wolof
6978
English
7585
Kurdish
8382
Serbian
8872
Xhosa
6979
Esperanto
7679
Laothian
8372
Serbo-Croatian
7473
Yiddish
6984
Estonian
7665
Latin
8378
Shona
8979
Yoruba
7079
Faeroese
7686
Latvian, Lettish
8368
Sindhi
9085
Zulu
1-90
Country/Area Code List
Code
AD
AE
AF
AG
AI
AL
AM
AN
AO
AQ
AR
AS
AT
AU
AW
AZ
BA
BB
BD
BE
BF
BG
BH
BI
BJ
BM
BN
BO
BR
BS
BT
BV
BW
BY
BZ
CA
CC
CF
CG
CH
CI
CK
CL
CM
CN
CO
CR
CS
CU
CV
CX
CY
CZ
DE
DJ
DK
DM
DO
DZ
EC
EE
EG
EH
Country/Area
Andorra
United Arab Emirates
Afghanistan
Antigua and Barbuda
Anguilla
Albania
Armenia
Netherlands Antilles
Angola
Antarctica
Argentina
American Samoa
Austria
Australia
Aruba
Azerbaidjan
Bosnia-Herzegovina
Barbados
Bangladesh
Belgium
Burkina Faso
Bulgaria
Bahrain
Burundi
Benin
Bermuda
Brunei Darussalam
Bolivia
Brazil
Bahamas
Bhutan
Bouvet Island
Botswana
Belarus
Belize
Canada
Cocos (Keeling) Islands
Central African Republic
Congo
Switzerland
Ivory Coast
Cook Islands
Chile
Cameroon
China
Colombia
Costa Rica
Former Czechoslovakia
Cuba
Cape Verde
Christmas Island
Cyprus
Czech Republic
Germany
Djibouti
Denmark
Dominica
Dominican Republic
Algeria
Ecuador
Estonia
Egypt
Western Sahara
Code
ER
ES
ET
FI
FJ
FK
FM
FO
FR
FX
GA
GB
GD
GE
GF
GH
GI
GL
GM
GN
GP
GQ
GR
GS
GT
GU
GW
GY
HK
HM
HN
HR
HT
HU
ID
IE
IL
IN
IO
IQ
IR
IS
IT
JM
JO
JP
KE
KG
KH
KI
KM
KN
KP
KR
KW
KY
KZ
LA
LB
Country/Area
Eritrea
Spain
Ethiopia
Finland
Fiji
Falkland Islands
Micronesia
Faroe Islands
France
France (European
Territory)
Gabon
Great Britain
Grenada
Georgia
French Guyana
Ghana
Gibraltar
Greenland
Gambia
Guinea
Guadeloupe (French)
Equatorial Guinea
Greece
S. Georgia & S. Sandwich
Isls.
Guatemala
Guam (USA)
Guinea Bissau
Guyana
Hong Kong
Heard and McDonald
Islands
Honduras
Croatia
Haiti
Hungary
Indonesia
Ireland
Israel
India
British Indian Ocean
Territory
Iraq
Iran
Iceland
Italy
Jamaica
Jordan
Japan
Kenya
Kyrgyzstan
Cambodia6
Kiribati
Comoros
Saint Kitts & Nevis Anguilla
North Korea
South Korea
Kuwait
Cayman Islands
Kazakhstan
Laos
Lebanon
Code
LC
LI
LK
LR
LS
LT
LU
LV
LY
MA
MC
MD
MG
MH
MK
ML
MM
MN
MO
MP
MQ
MR
MS
MT
MU
MV
MW
MX
MY
MZ
NA
NC
NE
NF
NG
NI
NL
NO
NP
NR
NU
NZ
OM
PA
PE
PF
PG
PH
PK
PL
PM
PN
PR
PT
PW
PY
QA
RE
RO
RU
RW
SA
SB
1-91
Country/Area
Saint Lucia
Liechtenstein
Sri Lanka
Liberia
Lesotho
Lithuania
Luxembourg
Latvia
Libya
Morocco
Monaco
Moldavia
Madagascar
Marshall Islands
Macedonia
Mali
Myanmar
Mongolia
Macau
Northern Mariana Islands
Martinique (French)
Mauritania
Montserrat
Malta
Mauritius
Maldives
Malawi
Mexico
Malaysia
Mozambique
Namibia
New Caledonia (French)
Niger
Norfolk Island
Nigeria
Nicaragua
Netherlands
Norway
Nepal
Nauru
Niue
New Zealand
Oman
Panama
Peru
Polynesia (French)
Papua New Guinea
Philippines
Pakistan
Poland
Saint Pierre and Miquelon
Pitcairn Island
Puerto Rico
Portugal
Palau
Paraguay
Qatar
Reunion (French)
Romania
Russian Federation
Rwanda
Saudi Arabia
Solomon Islands
Code
SC
SD
SE
SG
SH
SI
SJ
SK
SL
SM
SN
SO
SR
ST
SU
SV
SY
SZ
TC
TD
TF
TG
TH
TJ
TK
TM
TN
TO
TP
TR
TT
TV
TW
TZ
UA
UG
UK
UM
US
UY
UZ
VA
VC
VE
VG
VI
VN
VU
WF
WS
YE
YT
YU
ZA
ZM
ZR
ZW
Country/Area
Seychelles
Sudan
Sweden
Singapore
Saint Helena
Slovenia
Svalbard and Jan Mayen
Islands
Slovak Republic
Sierra Leone
San Marino
Senegal
Somalia
Suriname
Saint Tome and Principe
Former USSR
El Salvador
Syria
Swaziland
Turks and Caicos Islands
Chad
French Southern
Territories
Togo
Thailand
Tadjikistan
Tokelau
Turkmenistan
Tunisia
Tonga
East Timor
Turkey
Trinidad and Tobago
Tuvalu
Taiwan
Tanzania
Ukraine
Uganda
United Kingdom
USA Minor Outlying
Islands
United States
Uruguay
Uzbekistan
Vatican City State
Saint Vincent &
Grenadines
Venezuela
Virgin Islands (British)
Virgin Islands (USA)
Vietnam
Vanuatu
Wallis and Futuna Islands
Samoa
Yemen
Mayotte
Yugoslavia
South Africa
Zambia
Zaire
Zimbabwe
REFERENCE
Enter the appropriate code number for the initial setting “Area Code” (See page 21).
Specifications
General
Power requirements
Power consumption
Dimensions (approx.)
Mass (approx.)
Operating temperature
Operating humidity
Signal system
AC 120V , 60 Hz
23W
430 X 97.5 X 293 mm (16.9 x 3.9 x 11.5 inches) (w x h x d)
4.8 kg (10.58 lbs)
5˚C to 40˚C (41˚F to 104˚F)
5 % to 90 %
NTSC
Inputs
ANTENNA IN
VHS VIDEO IN (LINE1, 2)
VHS AUDIO IN (LINE1, 2)
Antenna or CATV input, 75 ohms
1 Vp-p 75 ohms, sync negative, RCA jack x 2
-6.0 dBm more than 47 kohms, RCA jack (L, R) x 2
Outputs
VIDEO OUT
S-VIDEO OUT
COMPONENT VIDEO OUT
(Progressive Scan)
Audio output (digital audio)
Audio output (optical audio)
Audio output (analog audio)
RF OUT
1 Vp-p 75 ohms, sync negative
(Y) 1.0 V (p-p), 75 ohms, negative sync, Mini DIN 4-pin x 1
(C) 0.3 V (p-p) 75 ohms
(Y) 1.0 V (p-p), 75 ohms, negative sync, RCA jack x 1
(Pb)/(Pr) 0.7 V (p-p), 75 ohms, RCA jack x 2
0.5 V (p-p), 75 ohms, RCA jack x 1
5 V (p-p), 75 Ω, Optical connector x 1
2.0 Vrms (1 KHz, 0 dB), 330 ohms, RCA jack (L, R) x 1
Channel 3 or 4
VCR Specifications
Head system
Timer
Tape speed
Tape width
Maximum recording time
Rewind time
Antenna
VHF output signal
Channel coverage
Frequency range
Signal-to-noise ratio
Dynamic range
Channel separation
Four head helical scan azimuth system
12-hour display type with AM, PM
SP: 33.35 mm/sec, LP: 16.67 mm/sec, SLP: 11.12 mm/sec
12.7 mm
SP: 2 HOURS (T-120), SLP: 6 HOURS (T-120)/8 HOURS (T-160)
About 3 minutes (T-120)
75 ohms (VHF/UHF)
Channel 3 or 4 (Switchable)
VHF: 2-13, UHF: 14-69, CATV: 1-125 (4A, A-W, W+1 - W+84, A-5 - A-1)
20Hz to 20kHz
More than 43dB
More than 88 dB
More than 60 dB
DVD Specifications
Laser system
Frequency response
Signal-to-noise ratio
Harmonic distortion
Dynamic range
Semiconductor laser, wavelength 650 nm
DVD (PCM 96 kHz): 8 Hz to 44 kHz, DVD (PCM 48 kHz): 8 Hz to 22 kHz
CD: 8 Hz to 20 kHz
More than 100dB (ANALOG OUT jacks only)
Less than 0.008%
More than 95 dB (DVD/CD)
Accessory:
Video cable x 1, Audio cable x 1, RF 75-ohm Coaxial Cable x 1, Remote control x 1, Batteries(AAA) x 2
z
Design and specifications are subject to change without notice.
Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories.
Confidential unpublished works. Copyright 1992-1997 Dolby Laboratories. All rights reserved.
DTS and DTS Digital Out are trademarks of Digital Theater Systems, Inc.
1-92
LIMITED WARRANTY DVD VIDEO PLAYER
Limited Ninety (90) Day Warranty
TACP/THI warrant this product against defects in materials or
workmanship for a period of ninety (90) days after the date of
original retail purchase. During this period, TACP/ THI will
repair or replace a defective product or part, at their option,
with a new or refurbished product or part without charge to
you. You must deliver the entire product to a TACP/THI
Authorized Service Station. You are responsible for all transportation and insurance charges for the unit to and from the
Authorized Service Station. If you live in the
U.S.A. you may, at your option, return your DVD Unit to:
Toshiba America Consumer Products Inc.
Returns Center
1420C Toshiba Dr.
Lebanon, TN 37087
Upon receipt we will, at our option, exchange the DVD Unit
with a new or refurbished unit. Canadian consumers are
requested to contact TCL. In Hawaii consumers are
requested to contact THI.
Commercial Units
Products sold and used for commercial use have a limited
ninety (90) day warranty for all parts and labor.
Owner’s Manual
You should read the owner’s manual thoroughly before operating this product. You should complete and mail the enclosed
Demographic card within ten (10) days after you, or the person
who has given you this product as a gift, purchased this product. This is one way to enable TACP to provide you with better
customer service and improved products. Failure to return the
card will not affect your rights under this warranty.
Limited One (1) Year Warranty
TACP/THI further warrant the parts in this product against
defects in materials or workmanship for a period of one (1)
year after the date of original retail purchase. During this period, TACP/THI will repair or replace a defective product or part,
at their option, with a new or refurbished product or part without charge to you, except that if a defective part is replaced
after ninety (90) days from the date of the original retail purchase you pay labor charges involved in the replacement. You
must also deliver the entire product to a TACP/THI Authorized
Service Station. You are responsible for all transportation and
insurance charges for the unit to and from the Authorized
Service Station. If you live in the U.S.A. you may, at your
option, return your DVD Unit to:
Toshiba America Consumer Products Inc.
Returns Center
1420C Toshiba Dr.
Lebanon, TN 37087
Upon receipt we will, at our option, exchange the DVD Unit
with a new or refurbished unit. Canadian Consumers are
requested to contact TCL. In Hawaii consumers are
requested to contact THI.
Rental Units
The warranty for rental units begin with the first rental or thirty
(30) days from the date of shipment to the rental firm, whichever comes first.
Your Responsibility
The above warranties are subject to the following conditions:
(1) You must retain your bill of sale or provide other proof of
purchase.
(2) You must notify a TACP/THI/TCL /Authorized Service
Station within thirty (30) days after you discover a defective
product or part.
(3) All warranty servicing of this product must be made by a
TACP/THI/TCL Authorized Service Station.
(4) U.S.A. warranties are effective only if the product is purchased and operated in the Continental U.S.A. or Puerto
Rico.
(5) Labor service charges for set installation. Set up, adjustment of customer controls and installation or repair of
antenna systems are not covered by this warranty.
Reception problems caused by inadequate antenna systems are your responsibility.
(6) Warranties extend only to defects in materials or workmanship as limited above and do not extend to any product or
parts which have been lost or discarded by you or to damage to products or parts caused by misuse, accident, damage caused by Acts of God, such as lighting or fluctuations
in electric power, improper installation, improper maintenance or use in violation of instructions furnished by us; or
to units which have been altered or modified without authorization of TACP/THI/TCL or to damage to products or part
thereof which have had the serial number removed,
altered, defaced or rendered illegible.
(7) Should you elect to return your DVD Unit to TACP after the
ninety (90) days and within one (1) year, or after the warranty period has expired: Call (800)-631-3811 to receive
information concerning an exchange price. Payment must
be enclosed with product in the form of a certified check or
money order including reason for return.
(8) Physically damaged DVD Units are not acceptable for
repair or exchange whether in or out of warranty and will
be returned as received.
(Continued)
1-93
REFERENCE
Toshiba America Consumer Products, Inc. (“TACP”), Toshiba Hawaii (“THI”) and Toshiba Canada Limited (“TCL”) make the following limited warranties. These limited warranties extend to original purchaser or any person receiving this set as a gift from the original purchaser and to no other purchaser or transferee.
LIMITED WARRANTY DVD VIDEO PLAYER (Continued)
How to Obtain Warranty Service
(1) Refer to the troubleshooting guide in your owner’s manual. This check list may solve your problem.
(2) In the U.S.A., only call the TACP toll free number 800-631-3811, or if in Hawaii or Canada see listing below within (30) days
after you find a defective product or part.
(3) Arrange for the delivery of the product to the TACP/THI/TCL Authorized Service Station or TACP Return Center. Products
shipped to the Service Station must be insured and safely and securely packed, preferably in the original shipping carton,
and a letter explaining the defect and also a copy of the bill of sale or other proof of purchase must be enclosed.
In the Continental United States contact:
Toll Free
800-631-3811
In Hawaii contact:
Toshiba Hawaii Inc.
327 Kamakee Street
Honolulu, HA 96814
(808)-521-5377
In Canada contact:
Consumer Electronics Group
191 McNabb Street
Markham, Ontario L3R 8H2
(905)-470-5400
Consumer Electronics Group
22171 Fraserwood Way
Richmond, B.C. V6W 1J5
(604)-303-2500
Consumer Electronics Group
1643 North Service Road
Droval, QC H9P 1J1
(514)-856-4100
All warranties implied by state law, including the implied warranties of merchantability and fitness for a particular purpose, are
expressly limited to the duration of the limited warranties set forth above. With the exception of any warranties implied by state law
as hereby limited, the foregoing warranty is exclusive and in lieu of all other warranties, guarantees, agreements and similar obligations of manufacturer or seller with respect to the repair or replacement of any parts. In no event shall TACP/THI be liable for
consequential or incidental damages.
No person, agent, distributor, dealer or company is authorized to change, modify or extend the terms of these warranties in any
manner whatsoever. The time within which an action must be commenced to enforce any obligation of TACP/THI arising under the
warranty or under any statute, or law of the United States or any state thereof, is hereby limited to ninety (90) days from the date
you discover or should have discovered, the defect. This limitation does not apply to implied warranties arising under state law.
This warranty gives you specific legal rights and you may also have other rights which may vary from state to state. Some states
do not allow limitation on how long an implied warranty lasts, when an action may be brought, or the exclusion or limitation of incidental or consequential damages, so the above provisions may not apply to you.
ATTENTION CANADIAN CONSUMERS:
Canadian consumers are requested to complete the special Canadian “Warranty Registration Form” enclosed, and forward this
completed form with a copy of bill of sale to TOSHIBA OF CANADA to “Register and Validate” their warranty. Product must be
purchased from an Authorized Canadian Dealer. Products purchased in the U.S.A. and used in Canada are not covered by
these warranties.
IMPORTANT: PACKING AND SHIPPING INSTRUCTION
When you send the product to a Service Station, you must use the original carton box and packing material, then insert the
original carton box containing the unit into another carton using more packing material.
1-94
PRODUCT SAFETY SERVICING GUIDELINES FOR VIDEO PRODUCTS
CAUTION : DO NOT ATTEMPT TO MODIFY THIS PRODUCT IN ANY WAY,
NEVER PERFORM CUSTOMIZED INSTALLATIONS WITHOUT MANUFACTURER’S APPROVAL. UNAUTHORIZED MODIFICATIONS WILL NOT ONLY
VOID THE WARRANTY, BUT MAY LEAD TO YOUR BEING LIABLE FOR ANY
RESULTING PROPERTY DAMAGE OR USER INJURY.
SERVICE WORK SHOULD BE PERFORMED ONLY AFTER YOU ARE
THOROUGHLY FAMILIAR WITH ALL OF THE FOLLOWING SAFETY
CHECKS AND SERVICING GUIDELINES. TO DO OTHERWISE,
INCREASES THE RISK OF POTENTIAL HAZARDS AND INJURY TO THE
USER.
WHILE SERVICING, USE AN ISOLATION TRANSFORMER FOR PROTECTION FROM A.C. LINE SHOCK.
SAFETY CHECKS
AFTER THE ORIGINAL SERVICE PROBLEM HAS BEEN CORRECTED. A
CHECK SHOULD BE MADE OF THE FOLLOWING.
SUBJECT : FIRE & SHOCK HAZARD
1. BE SURE THAT ALL COMPONENTS ARE POSITIONED IN SUCH A WAY
AS TO AVOID POSSIBILITY OF ADJACENT COMPONENT SHORTS.
THIS IS ESPECIALLY IMPORTANT ON THOSE MODULES WHICH ARE
TRANSPORTED TO AND FROM THE REPAIR SHOP.
2. NEVER RELEASE A REPAIR UNLESS ALL PROTECTIVE DEVICES
SUCH AS INSULATORS, BARRIERS, COVERS, SHIELDS, STRAIN
RELIEFS, POWER SUPPLY CORDS, AND OTHER HARDWARE HAVE
BEEN REINSTALLED PER ORIGINAL DESIGN. BE SURE THAT THE
SAFETY PURPOSE OF THE POLARIZED LINE PLUG HAS NOT BEEN
DEFEATED.
3. SOLDERING MUST BE INSPECTED TO DISCOVER POSSIBLE COLD
SOLDER JOINTS, SOLDER SPLASHES OR SHARP SOLDER POINTS.
BE CERTAIN TO REMOVE ALL LOOSE FOREIGN PARTICLES.
4. CHECK FOR PHYSICAL EVIDENCE OF DAMAGE OR DETERIORATION
TO PARTS AND COMPONENTS. FOR FRAYED LEADS, DAMAGED
INSULATION (INCLUDING A.C. CORD). AND REPLACE IF NECESSARY
FOLLOW ORIGINAL LAYOUT, LEAD LENGTH AND DRESS.
5. NO LEAD OR COMPONENT SHOULD TOUCH A RECIVING TUBE OR
A RESISTOR RATED AT 1 WATT OR MORE. LEAD TENSION AROUND
PROTRUNING METAL SURFACES MUST BE AVOIDED.
6. ALL CRITICAL COMPONENTS SUCH AS FUSES, FLAMEPROOF
RESISTORS, CAPACITORS, ETC. MUST BE REPLACED WITH EXACT
FACTORY TYPES, DO NOT USE REPLACEMENT COMPONENTS
OTHER THAN THOSE SPECIFIED OR MAKE UNRECOMMENDED CIRCUIT MODIFICATIONS.
7. AFTER RE-ASSEMBLY OF THE SET ALWAYS PERFORM AN A.C.
LEAKAGE TEST ON ALL EXPOSED METALLIC PARTS OF THE CABINET, (THE CHANNEL SELECTOR KNOB, ANTENNA TERMINALS. HANDLE AND SCREWS) TO BE SURE THE SET IS SAFE TO OPERATE
WITHOUT DANGER OF ELECTRICAL SHOCK. DO NOT USE A LINE
ISOLATION TRANSFORMER DURING THIS TEST USE AN A.C. VOLTMETER, HAVING 5000 OHMS PER VOLT OR MORE SENSITIVITY, IN
THE FOLLOWING MANNER; CONNECT A 1500 OHM 10 WATT RESISTOR, PARALLELED BY A .15 MFD. 150.V A.C TYPE CAPACITOR
BETWEEN A KNOWN GOOD EARTH GROUND (WATER PIPE, CONDUIT, ETC.) AND THE EXPOSED METALLIC PARTS, ONE AT A TIME.
MEASURE THE A.C. VOLTAGE ACROSS THE COMBINATION OF 1500
OHM RESISTOR AND .15 MFD CAPACITOR. REVERSE THE A.C. PLUG
AND REPEAT A.C. VOLTAGE MEASUREMENTS FOR EACH EXPOSED
METALLIC PART. VOLTAGE MEASURED MUST NOT EXCEED 75
VOLTS R.M.S. THIS CORRESPONDS TO 0.5 MILLIAMP A.C ANY
VALUE EXCEEDING THIS LIMIT CONSTITUTES A POTENTIAL SHOCK
HAZARD AND MUST BE CORRECTED IMMEDIATELY.
A.C. VOLTMETER
GOOD EARTH GROUND
SUCH AS THE WATER
PIPE. CONDUIT. ETC
PLACE THIS PROBE
ON EACH EXPOSED
METAL PART
SUBJECT: GRAPHIC SYMBOLS
THE LIGHTNING FLASH WITH APROWHEAD SYMBOL. WITHIN
AN EQUILATERAL TRIANGLE, IS INTENDED TO ALERT THE
SERVICE PERSONNEL TO THE PRESENCE OF UNINSULATED
“DANGEROUS VOLTAGE” THAT MAY BE OF SUFFICIENT MAGNITUDE TO CONSTITUTE A RISK OF ELECTRIC SHOCK.
THE EXCLAMATION POINT WITHIN AN EQUILATERAL TRIANGLE IS INTENDED TO ALERT THE SERVICE PERSONNEL TO
THE PRESENCE OF IMPORTANT SAFETY INFORMATION IN
SERVICE LITERATURE.
SUBJECT : X-RADIATION
1. BE SURE PROCEDURES AND INSTRUCTIONS TO ALL SERVICE PERSONNEL COVER THE SUBJECT OF X-RADIATION. THE ONLY POTENTIAL SOURCE OF X-RAYS IN CURRENT T.V. RECEIVERS IS THE PICTURE TUBE. HOWEVER, THIS TUBE DOES NOT EMIT X-RAYS WHEN
THE HIGH VOLTAGE IS AT THE FACTORY SPECIFIED LEVEL. THE
PROPER VALUE IS GIVEN IN THE APPLICABLE SCHEMATIC. OPERATION AT HIGHER VOLTAGES MAY CAUSE A FAILURE OF THE PICTURE TUBE OR HIGH VOLTAGE SUPPLY AND, UNDER CERTAIN CIRCUMSTANCES, MAY PRODUCE RADIATION IN EXCESS OF DESIRABLE LEVELS.
2. ONLY FACTORY SPECIFIED C.R.T. ANODE CONNECTORS MUST BE
USED. DEGAUSSING SHIELDS ALSO SERVE AS X-RAY SHIELD IN
COLOR SETS, ALWAYS RE-INSTALL THEM.
3. IT IS ESSNTIAL THAT SERVICE PERSONNEL HAVE AVAILABLE AN
ACCURATE AND RELIABLE HIGH VOLTAGE METER. THE CALIBRA
TION OF THE METER SHOULD BE CHECKED PERIODICALLY
AGAINST A REFERENCE STANDARD, SUCH AS THE ONE AVAILABLE
AT YOUR DISTRIBUTOR.
4. WHEN THE HIGH VOLTAGE CIRCUITRY IS OPERATING PROPERLY
THERE IS NO POSSIBILITY OF AN X-RADIATION PROBLEM. EVERY
TIME A COLOR CHASSIS IS SERVICED. THE BRIGHTNESS SHOULD
BE RUN UP AND DOWN WHILE MONITORING THE HIGH VOLTAGE
WITH A METER TO BE CERTAIN THAT THE HIGH VOLTAGE DOES
NOT EXCEED THE SPECIFIED VALUE AND THAT IT IS REGULATING
CORRECTLY, WE SUGGEST THAT YOU AND YOUR SERVICE ORGANIZATION REVIEW TEST PROCEDURES SO THAT VOLTAGE REGULATION IS ALWAYS CHECKED AS A STANDARD SERVICING PROCEDURE. AND THAT THE HIGH VOLTAGE READING BE RECORDER ON
EACH CUSTOMER’S INVOICE.
5. WHEN TROUBLESHOOTING AND MAKING TEST MEASUREMENTS IN
A PRODUCT WITH A PROBLEM OF EXCESSIVE HIGH VOLTAGE,
AVOID BEING UNNECESSARILY CLOSE TO THE PICTURE TUBE AND
THE HIGH VOLTAGE SUPPLY. DO NOT OPERATE THE PRODUCT
LONGER THAN IS NECESSARY TO LOCATE THE CAUSE OF EXCES
SIVE VOLTAGE.
6. REFER TO HV. B+ AND SHUTDOWN ADJUSTMENT PROCEDURES
DESCRIBED IN THE APPROPRIATE SCHEMATIC AND DIAGRAMS
(WHERE USED).
SUBJECT: IMPLOSION
1. ALL DIRECT VIEWED PICTURE TUBES ARE EQUIPPED WITH AN INTE
GRAL IMPLOSION PROTECTION SYSTEM, BUT CARE SHOULD BE
TAKEN TO AVOID DAMAGE DURING INSTALLATION, AVOID
SCRATCHING THE TUBE. IF SCRATCHED REPLACE IT.
2. USE ONLY RECOMMENDED FACTORY REPLACEMENT TUBES.
SUBJECT : TIPS ON PROPER INSTALLATION
1. NEVER INSTALL ANY PRODUCT IN A CLOSED-IN RECESS, CUBBYHOLE OR CLOSELY FITTING SHELF SPACE. OVER OR CLOSE TO
HEAT DUCT, OR IN THE PATH OF HEATED AIR FLOW.
2. AVOID CONDITIONS OF HIGH HUMIDITY SUCH AS: OUTDOOR PATIO
INSTALLATIONS WHERE DEW IS A FACTOR, NEAR STEAM RADIATORS WHERE STEAM LEAKAGE IS A FACTOR, ETC.
3. AVOID PALCEMENT WHERE DRAPERIES MAY OBSTRUCT REAR
VENTING. THE CUSTOMER SHOULD ALSO AVOID THE USE OF DECORATIVE SCARVES OR OTHER COVERINGS WHICH MIGHT
OBSTRUCT VENTILATION.
4. WALL AND SHELF MOUNTED INSTALLATIONS USING A COMMERCIAL MOUNTING KIT. MUST FOLLOW THE FACTORY APPROVED
MOUNTING INSTRUCTIONS A PRODUCT MOUNTED TO A SHELF OR
PLATFORM MUST RETAIN ITS ORIGINAL FEET (OR THE EQUIVALENT
THICKNESS IN SPACERS) TO PROVIDE ADEQUATE AIR FLOW
ACROSS THE BOTTOM, BOLTS OR SCREWS USED FOR FASTENERS
MUST NOT TOUCH ANY PARTS OR WIRING. PERFORM LEAKAGE
TEST ON CUSTOMIZED INSTALLATIONS.
5. CAUTION CUSTOMERS AGAINST THE MOUNTING OF A PRODUCT ON
SLOPING SHELF OR A TILTED POSITION, UNLESS THE PRODUCT IS
PROPERLY SECURED.
6. A PRODUCT ON A ROLL-ABOUT CART SHOULD BE STABLE ON ITS
MOUNTING TO THE CART. CAUTION THE CUSTOMER ON THE HAZARDS OF TRYING TO ROLL A CART WITH SMALL CASTERS ACROSS
THRESHOLDS OR DEEP PILE CARPETS.
7. CAUTION CUSTOMERS AGAINST THE USE OF A CART OR STAND
WHICH HAS NOT BEEN LISTED BY UNDERWRITERS LABORATORIES,
INC. FOR USE WITH THEIR SPECIFIC MODEL OF TELEVISION
RECEIVER OR GENERICALLY APPROVED FOR USE WITH T.V.’S OF
THE SAME OR LARGER SCREEN SIZE.
8. CAUTION CUSTOMERS AGAINST THE USE OF EXTENSION CORDS,
EXPLAIN THAT A FOREST OF EXTENSIONS SPROUTING FROM A SINGLE OUTLET CAN LEAD TO DISASTROUS CONSEQUENCES TO
HOME AND FAMILY.
1-95
SERVICING PRECAUTIONS
CAUTION : Before servicing the VCR+DVD covered by this
service data and its supplements and addends, read and follow the SAFETY PRECAUTIONS. NOTE : if unforeseen circumstances create conflict between the following servicing
precautions and any of the safety precautions in this publications, always follow the safety precautions.
Remembers Safety First:
General Servicing Precautions
1. Always unplug the VCR+DVD AC power cord from the AC
power source before:
(1) Removing or reinstalling any component, circuit board,
module, or any other assembly.
(2) Disconnection or reconnecting any internal electrical
plug or other electrical connection.
(3) Connecting a test substitute in parallel with an electrolytic capacitor.
Caution : A wrong part substitution or incorrect
polarity installation of electrolytic capacitors may result
in an explosion hazard.
2. Do not spray chemicals on or near this VCR+DVD or any
of its assemblies.
3. Unless specified otherwise in this service data, clean
electrical contacts by applying an appropriate contact
cleaning solution to the contacts with a pipe cleaner,
cotton-tipped swab, or comparable soft applicator.
Unless specified otherwise in this service data, lubrication
of contacts is not required.
4. Do not defeat any plug/socket B+ voltage interlocks with
whitch instruments covered by this service manual might
be equipped.
5. Do not apply AC power to this VCR+DVD and/or any of its
electrical assemblies unless all solid-state device heat
sinks are cerrectly installed.
6. Always connect test instrument ground lead to the
appropriate ground before connection the test instrument
positive lead. Always remove the test instrument ground
lead last.
Insulation Checking Procedure
Disconnect the attachment plug from the AC outlet and turn
the power on. Connect an insulation resistance meter(500V)
to the blades of the attachment plug. The insulation resistance between each blade of the attachment plug and accessible conductive parts (Note 1) should be more than 1Mohm.
Note 1 : Accessible Conductive Parts including Metal panels, Input terminals, Earphone jacks, etc.
Electrostatically Sensitive (ES) Devices
Some semiconductor (solid state) devices can be damaged
easily by static electricity. Such components commonly are
called Electrostatically Sensitive (ES) Devices. Examples of
typical ES devices are integrated circuits and some field
effect transistors and semiconductor chip components.
The following techniques should be used to help reduce the
incidence of component damage caused by static electricity.
1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any
electrostatic charge on your body by touching a known
earth ground. Alternatively, obtain and wear a commercially available discharging wrist strap device, which
should be removed for potential shock reasons prior to
applying power to the unit under test.
2. After removing an electrical assembly equipped with ES
devices, place the assembly on a conductive surface such
as aluminum foil, to prevent electrostatic charge buildup or
exposure of the assembly.
3. Use only a grouned-tip soldering iron to solder or unsolder
ES devices.
4. Use only an anti-static solder removal device. Some
solder removal devices not classified a “anti-static” can
generate electrical charges sufficient to damage ES
devices.
5. Do not use freon-propelled chemicals. These can
generate electrical charge sufficient to damage ES
devices.
6. Do not remove a replacement ES device from its protec
tive package until immediately before you are ready to
install it. (Most replacement ES devices are packaged with
leads electrically shorted together by conductive foam,
aluminum foil, or comparable conductive material).
7. Immediately before removing the protective material from
the leads of a replacement ES device, touch the protective
material to the chassis or circuit assembly into which the
device will be installed.
Caution : Be sure no power is applied to the chassis or
circuit, and observe all other safety precautions.
8. Minimize bodily motions when handling unpackaged
replacement ES devices. (Normally harmless motion such
as the brushing together of your clothes fabric or the lifting
of your foot from a carpeted floor can generate static electricity sufficient to damage an ES device.)
1-96
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement