Toshiba SD-V594SC Speaker System User Manual

Toshiba SD-V594SC Speaker System User Manual
Introduction
Connections
DVD VIDEO PLAYER & VIDEO
CASSETTE RECORDER
SD-V594SC
OWNER’S MANUAL
This device does not tape-record copy protected DVD Video Discs.
2I40301A-En_cov
1
21/3/06, 9:41 AM
16
Basic setup
(VCR)
27
Playback
(VCR)
34
Recording
(VCR)
39
Other functions
(VCR)
44
Basic playback
(DVD)
47
Advanced
playback
(DVD)
50
Function setup
(DVD)
63
Others
©2006 Toshiba Corporation
2
71
Introduction
SAFETY PRECAUTIONS
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
The lightning flash with arrowhead symbol, within an
equilateral triangle is intended to alert the user to the presence
of uninsulated dangerous voltage within the product's
enclosure that may be of sufficient magnitude to constitute a
risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended
to alert the user to the presence of important operating and
maintenance (servicing) instructions in the literature
accompanying the appliance.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, do not expose this appliance to rain
or moisture.
CAUTION: TO PREVENT ELECTRIC SHOCK DO NOT USE THIS POLARIZED PLUG WITH AN
EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN
BE FULLY INSERTED TO PREVENT BLADE EXPOSURE.
ATTENTION: POUR EVITER LES CHOCS ELECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA
FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.
FCC NOTICE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV technician for help.
CAUTION: Changes or modifications not expressly approved by the partly responsible for compliance with the
FCC Rules could void the user's authority to operate this equipment.
CAUTION: THIS DIGITAL VIDEO PLAYER EMPLOYS A LASER SYSTEM.
TO ENSURE PROPER USE OF THIS PRODUCT, PLEASE READ THIS USER'S GUIDE CAREFULLY AND RETAIN FOR FUTURE REFERENCE. SHOULD THE UNIT REQUIRE MAINTENANCE, CONTACT AN AUTHORIZED SERVICE LOCATION.
USE OF CONTROLS, ADJUSTMENTS OR THE PERFORMANCE OF PROCEDURES OTHER
THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
TO PREVENT DIRECT EXPOSURE TO LASER BEAM, DO NOT TRY TO OPEN THE ENCLOSURE. VISIBLE LASER RADIATION MAY BE PRESENT WHEN THE ENCLOSURE IS OPENED.
DO NOT STARE INTO BEAM.
Location of the required Marking
The rating sheet and the safety caution are on the rear of the unit.
2
CERTIFICATION: COMPLIES WITH FDA RADIATION PERFORMANCE
STANDARDS, 21 CFR SUBCHAPTER J.
2I40301A-En_p02-13
2
21/3/06, 9:41 AM
IMPORTANT SAFEGUARDS
Introduction
1. READ INSTRUCTIONS
All the safety and operating instructions should be read before the unit is operated.
2. RETAIN INSTRUCTIONS
The safety and operating instructions should be retained for future reference.
3. HEED WARNINGS
All warnings on the unit and in the operating instructions should be adhered to.
4. FOLLOW INSTRUCTIONS
All operating and use instructions should be followed.
5. CLEANING
Unplug this unit from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners.
Use a soft dry cloth for cleaning the exterior cabinet only.
6. ATTACHMENTS
The manufacturer of this unit does not make any recommendations for attachments, as they may cause
hazards.
7. WATER AND MOISTURE
Do not use this unit near water. For example, near a bathtub, washbowl, kitchen sink, laundry tub, in a wet
basement, or near a swimming pool.
PORTABLE CART WARNING
(symbol provided by RETAC)
8. ACCESSORIES
Do not place this unit on an unstable cart, stand, tripod, bracket, or table.
The unit may fall, causing serious injury, and serious damage to the unit.
8A. An appliance and cart combination should be moved with care. Quick stops,
excessive force, and uneven surfaces may cause the appliance and cart
combination to overturn.
9. VENTILATION
Slots and openings in the cabinet back or bottom are provided for ventilation,
S3125A
to ensure reliable operation of the unit, and to protect it from overheating.
These openings must not be blocked or covered. The openings should never be blocked by placing the unit
on a bed, sofa, rug, or other similar surface. This unit should never be placed near or over a radiator or heat
source. This unit should not be placed in a built-in installation such as a bookcase or rack unless proper
ventilation is provided and/or the manufacturer’s instructions have been adhered to.
10. POWER SOURCE
This unit should be operated only from the type of power source indicated on the rating plate. If you are not
sure of the type of power supply to your home, consult your appliance dealer or local power company.
11. GROUNDING OR POLARIZATION
This unit is equipped with a polarized alternating-current line plug (a plug having one blade wider than the
other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to
insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your
electrician to replace your obsolete outlet. Do not defeat the safety purpose of the grounding-type plug.
12. POWER-CORD PROTECTION
Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed
upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point
where they exit from the appliance.
3
2I40301A-En_p02-13
3
21/3/06, 9:41 AM
Introduction
IMPORTANT SAFEGUARDS
13. LIGHTNING
To protect your unit from a lightning storm, or when it is left unattended and unused for long periods of time,
unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the
unit due to lightning and power line surges.
14. POWER LINES
An outside antenna system should not be located in the vicinity of overhead power lines or other electric
light or power circuits, or where it can fall onto or against such power lines or circuits. When installing an
outside antenna system, extreme care should be taken to keep from touching such power lines or circuits,
as contact with them might be fatal.
15. OVERLOADING
Do not overload wall outlets and extension cords, as this can result in a risk of fire or electric shock.
16. OBJECT AND LIQUID ENTRY
Do not push objects through any openings in this unit, as they may touch dangerous voltage points or short
out parts that could result in fire or electric shock. Never spill or spray any type of liquid into the unit.
17. OUTDOOR ANTENNA GROUNDING
If an outside antenna or cable system is connected to the unit, be sure the antenna or cable system is
grounded to provide some protection against voltage surges and built-up static charges, Section 810 of the
National Electrical Code, ANSI/NFPA 70, provides information with respect to proper grounding of the mast
and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding
conductors, location of antenna discharge unit, connection to grounding electrodes, and requirements for
the grounding electrode.
EXAMPLE OF ANTENNA GROUNDING AS PER THE
NATIONAL ELECTRICAL CODE
ANTENNA LEAD IN WIRE
GROUND CLAMP
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
ELECTRIC SERVICE
EQUIPMENT
NEC-NATIONAL ELECTRICAL CODE
S2898A
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
18. SERVICING
Do not attempt to service this unit yourself as opening or removing covers may expose you to dangerous
voltage or other hazards. Refer all servicing to qualified service personnel.
For example:
a. When the power-supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen into the unit.
c. If the unit has been exposed to rain or water.
d. If the unit does not operate normally by following the operating instructions. Adjust only those controls that
are covered by the operating instructions, as an improper adjustment of other controls may result in damage
and will often require extensive work by a qualified technician to restore the unit to its normal operation.
e. If the unit has been dropped or the cabinet has been damaged.
f . When the unit exhibits a distinct change in performance, this indicates a need for service.
4
2I40301A-En_p02-13
4
21/3/06, 9:41 AM
IMPORTANT SAFEGUARDS / Power source
Introduction
19. REPLACEMENT PARTS
When replacement parts are required, be sure the service technician uses replacement parts specified by
the manufacturer or those that have the same characteristics as the original part.
Unauthorized substitutions may result in fire, electric shock or other hazards.
20. SAFETY CHECK
Upon completion of any service or repairs to this unit, ask the service technician to perform safety checks to
determine that the unit is in proper operating condition.
21. HEAT
The product should be situated away from heat sources such as radiators, heat registers, stoves, or other
products (including amplifiers) that produce heat.
22. DISC TRAY
Keep your fingers well clear of the disc tray as it is closing. It may cause serious personal injury.
23. CONNECTING
When you connect the product to other equipment, turn off the power and unplug all of the equipment from
the wall outlet. Failure to do so may cause a product damage. Read the owner's manual of the other
equipment carefully and follow the instructions when making any connections.
24. LASER BEAM
Do not look into the opening of the disc tray or ventilation opening of the product to see the source of the
laser beam. It may cause sight damage.
25. DISC
Do not use a cracked, deformed, or repaired disc. These discs are easily broken and may cause serious
personal injury and product malfunction.
26. NOTE TO CABLE TV SYSTEM INSTALLER
This reminder is provided to call the Cable TV system installer’s attention to Article 820-40 of the NEC that
provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.
Power source
AC Outlet
Wider Hole
and Blade
Polarized AC Cord Plug
(One blade is wider than the other.)
TO USE AC POWER SOURCE
Use the AC polarized line cord provided for operation on AC. Insert
the AC cord plug into a standard 120V 60Hz polarized AC outlet.
Notes:
• Never connect the AC line cord plug to other than the specified
voltage (120V 60Hz). Use the attached power cord only.
• If the polarized AC cord does not fit into a non-polarized AC
outlet, do not attempt to file or cut the blade. It is the user’s
responsibility to have an electrician replace the obsolete outlet.
• If you cause a static discharge when touching the unit and the
unit fails to function, simply unplug the unit from the AC outlet
and plug it back in. The unit should return to normal operation.
5
2I40301A-En_p02-13
5
21/3/06, 9:41 AM
Introduction
Precautions
Notes on handling
When shipping the DVD/VCR, the original shipping
carton and packing materials come in handy. For
maximum protection, repack the unit as it was
originally packed at the factory.
Do not use volatile liquids, such as insect spray, near
the DVD/VCR. Do not leave rubber or plastic
products to contact the DVD/VCR for a prolonged
period. They will leave marks on the finish.
The top and rear panels of the DVD/VCR may
become warm after a long period of use. This is not a
malfunction.
When the DVD/VCR is not in use, be sure to remove
the disc and the video cassette turn off the power.
If you do not use the DVD/VCR for a long period, the
unit may not function properly in the future. Turn on
and use the DVD/VCR occasionally.
Notes on locating
Place the DVD/VCR on a level surface. Do not use it
on a shaky or unstable surface such as a wobbling
table or inclined stand. The loaded disc or the video
tape may become dis-aligned and damage the DVD/
VCR.
When you place this DVD/VCR near a TV, radio, or
VCR, the playback picture may become poor and the
sound may be distorted. In this case, place the DVD/
VCR away from the TV, radio or VCR.
Note on moisture condensation
Moisture condensation damages the DVD/VCR.
Please read the following carefully.
Moisture condensation occurs, for example, when you
pour a cold drink into a glass on a warm day. Drops of
water form on the outside of the glass. In the same way,
moisture may condense on the head drum or the optical
pick-up lens inside this unit, one of the most crucial
internal parts of the DVD/VCR.
le of mo
Examp ensat isture
ion!
cond
Tape
Head drum
Moisture condensation occurs during the
following cases.
When you bring the DVD/VCR directly from a cold
place to a warm place.
When you use the DVD/VCR in a room where you
just turned on the heater, or a place where the cold
wind from the air conditioner directly hits the unit.
In summer, when you use the DVD/VCR in a hot and
humid place just after you move the unit from an air
conditioned room.
When you use the DVD/VCR in a humid place.
It’s too
warm!
Notes on cleaning
Use a soft, dry cloth for cleaning.
Use a dry cloth to wipe.
Do not use any type of solvent, such as thinner and
benzine, as they may damage the surface of the
DVD/VCR.
If you use a chemical saturated cloth to clean the unit,
follow that product’s instructions.
Do not use the DVD/VCR when moisture
condensation may occur.
If you use the DVD/VCR in such a situation, it may
damage discs and internal parts. Remove the disc or
the video tape, connect the power cord of the DVD/
VCR to the wall outlet, turn on the DVD/VCR, and
leave it for two or three hours. After two or three
hours, the DVD/VCR will have warmed up and
evaporated any moisture. Keep the DVD/VCR
connected to the wall outlet and moisture
condensation will seldom occur.
Wa
it!
6
2I40301A-En_p02-13
6
21/3/06, 9:41 AM
Wall outlet
Notes and Informations
On handling discs
Playable discs
This DVD/VCR can play the following discs.
Disc Mark
Contents
Disc
Size
Approx. 4 hours
(single sided disc)
Playback side
12 cm
Do not attach paper or tape to discs.
Approx. 160 minutes
(double sided disc)
Fingerprints and dust on the disc cause picture and
sound deterioration. Wipe the disc from the center
outwards with a soft cloth. Always keep the disc
clean.
Video
CDs
Do not use any type of solvent such as thinner,
benzine, commercially available cleaners or antistatic
spray for vinyl LPs. It may damage the disc.
Audio
CDs
DIGITAL VIDEO
Audio
+
Video
(moving
pictures)
Do not store discs in a place subject to direct sunlight
or near heat sources.
Do not store discs in places subject to moisture and
dust such as a bathroom or near a humidifier.
Store discs vertically in a case. Stacking or placing
objects on discs outside of their case may cause
warping.
Structure of disc contents
Normally, DVD video discs are divided into titles, and the
titles are sub-divided into chapters. VIDEO CDs and
audio CDs are divided into tracks.
DVD video disc
Title 1
Title 2
Chapter 1 Chapter 2
Chapter 1 Chapter 2 Chapter 3
Video CD/Audio CD
Video CD/Audio CD
Track 3
Track 4
Track 5
Each title, chapter or track is assigned a number, which
is called “title number”, “chapter number” or “track
number” respectively.
There may be discs that do not have these numbers.
12 cm
Approx. 74 minutes
(single sided disc)
8 cm
Approx. 20 minutes
(single sided disc)
12 cm
Approx. 74 minutes
(single sided disc)
8 cm
Approx. 20 minutes
(single sided disc)
Audio
On storing discs
Track 2
Approx. 80 minutes
(single sided disc)
8 cm
On cleaning discs
Track 1
Approx. 8 hours
(double sided disc)
Audio
+
Video
(moving
pictures)
DVD
video
discs
DVD video disc
Maximum
playback time
Introduction
Do not touch the playback side of the disc.
The following discs are also available.
DVD-R/RW discs of DVD video format
CD-R/CD-RW discs of CD-DA, Video CD, SVCD,
MP3, WMA, JPEG or DivX format
Kodak picture CD, FUJICOLOR CD format
Some of these discs may be incompatible.
• You cannot play discs other than those listed above.
• You cannot play discs of DVD-RAM, DVD-ROM, Photo
CD, etc., or non standardized discs even if they may be
labeled as above.
• Some CD-R/RWs cannot be played back depending on
the recording conditions.
• This DVD/VCR uses the NTSC color system, and
cannot play DVD video discs recorded in any other
color system (PAL, SECAM, etc.).
Because of problems and errors that can occur during
the creation of DVD and CD Software and/or the
manufacture of DVD and CD discs, Toshiba cannot
assure that the DVD player will successfully play every
disc bearing DVD and CD logos. If you happen to
experience any difficulty playing a DVD and/or CD disc
on this DVD player, please contact Toshiba Customer
Service.
is a trademark of DVD Format/Logo Licensing Corporation.
7
2I40301A-En_p02-13
7
21/3/06, 9:41 AM
Introduction
Notes and Informations (Continued)
Notes on region numbers
The region number of this DVD/VCR is 1. If region numbers, which
stand for their playable area, are printed on your DVD video
disc and you do not find 1 or ALL , disc playback will not be
allowed by the player. (In this case, the DVD/VCR will display a
message on-screen.)
On Video CDs
This DVD/VCR supports Video CDs equipped with the PBC
(Version 2.0) function. (PBC is the abbreviation of Playback
Control.) You can enjoy two playback variations depending on
types of discs.
• Video CD not equipped with PBC function
(Version 1.1)
Sound and movie can be played on this DVD/VCR in the
same way as an audio CD.
• Video CD equipped with PBC function
(Version 2.0)
In addition to operation of a Video CD not equipped with the
PBC function, you can enjoy playback of interactive software
with search function by using the menu displayed on the TV
screen (Menu Playback). Some of the functions described in
this owner’s manual may not work with some discs.
Playable USB Mass Storages
This unit is compatible with USB memory devices that accept Mass
Storage Class (referred to as USB Mass Storage in this owner’s
manual). Please note that this does not guarantee that the unit is
compatible with any kind of USB Mass Storage.
This unit can be used to read JPEG, WMA, MP3 and DivX® data
for the equipment shown in the table below. However, please note
that it is not possible to guarantee that all functions are available
and some functions may not work properly for some equipment.
This unit cannot playback the DivX® VOD content protected by
DRM (Digital Rights Management) system on the USB Mass
Storage.
This unit is compatible with Nikon COOLPIX P2 and FUJIFILM
FinePix A345 digital cameras. However, successful connection
depends on the version of the software installed in the camera
and the memory capacity and connection status.
This unit cannot be used to read data from equipment not listed
below.
Please refer to “Connecting to a USB Mass Storage” $ for details
of how to connect a USB Mass Storage and the necessary
precautions when using the unit.
Equipment
Memory Card
Reader
Digital Camera
USB Memory
MP3 Player
8
2I40301A-En_p02-13
Brand
Models
San Disk
ZIO
GE
Nikon
FUJIFILM
Lexar
San Disk
PNY
SAMSUNG
Sony
RCA
SDDR-89
CM-28100
HO97949
COOLPIX P2
FinePix A345
JDA1GB-275
SDCZ2-512-A10
PFD01GU20RF
YP-T7Z
NW-E507
RD2780
8
About this owner’s manual
This owner’s manual explains the basic instructions of
this DVD/VCR. Some DVD video discs are produced in
a manner that allows specific or limited operation during
playback. As such, the DVD/VCR may not respond to all
operating commands. This is not a defect in the DVD/
VCR. Refer to instruction notes of discs.
The following symbol may appear on the TV screen
during operation.
It means that the operation is not permitted by the DVD/
VCR or the disc.
For example, sometimes it is unable to stop the
playback of copyright message of the disc when the
STOP ( ) button is pressed. Alternatively, this symbol
may also indicate that the feature is not available for the
disc.
Notes on copyright
The unauthorized recording, use, distribution, or revision
of copyrighted materials including, without limitation,
television programs, videotapes, and DVDs is prohibited
under the Copyright Laws of the United States and other
countries, and may subject you to civil and criminal
liability.
This product incorporates copyright protection
technology that is protected by U.S. patents and other
intellectual property rights. Use of this copyright
protection technology must be authorized by
Macrovision, and is intended for home and other limited
viewing uses only unless otherwise authorized by
Macrovision. Reverse engineering or disassembly is
prohibited.
Consumers should note that not all high definition
television sets are fully compatible with this product and
may cause artifacts to be displayed in the picture. In
case of 525 progressive scan picture problems, it is
recommended that the user switch the connection to the
“STANDARD DEFINITION” output. If there are questions
regarding our TV set compatibility with this model 525p
DVD player, please contact our customer service center.
21/3/06, 9:41 AM
Contents
Basic playback (DVD)
SAFETY PRECAUTIONS ................................ 2
IMPORTANT SAFEGUARDS .......................... 3
Power source ................................................... 5
Precautions ...................................................... 6
Notes and Informations .................................... 7
Contents. .......................................................... 9
Identification of controls ................................. 10
Multi brand remote control ............................. 14
Playing a disc ................................................. 47
Connections
Antenna connections ...................................... 16
Cable TV connections .................................... 18
Connecting to a TV ........................................ 20
Connecting to an audio equipment ................ 24
Connecting to a USB Mass Storage .............. 26
Basic setup (VCR)
Setting the video channel ............................... 27
Setting the language ...................................... 28
Clock setting ................................................... 29
Tuner setting .................................................. 32
Playback (VCR)
Loading and unloading a cassette tape ......... 34
Cassette tape playback .................................. 35
Special playback ............................................ 36
Convenience function ..................................... 37
Recording (VCR)
Advanced playback (DVD)
Zooming ......................................................... 50
Locating desired scene .................................. 50
Marking desired scenes ................................. 51
Repeat playback ............................................ 52
A-B Repeat playback ..................................... 52
Program playback .......................................... 53
Random playback .......................................... 53
Changing angles ............................................ 54
Title selection ................................................. 54
DVD menu ...................................................... 54
Changing soundtrack language ..................... 55
Setting surround sound .................................. 55
Subtitles ......................................................... 56
To turn off the PBC ......................................... 56
MP3/WMA/JPEG/DivX® and Audio CD
operation ........................................................ 57
Introduction
Introduction
Function setup (DVD)
Customizing the function settings .................. 63
Temporary disabling of rating level by
DVD disc ........................................................ 70
Others
Language code list ......................................... 71
Troubleshooting ............................................. 72
Specifications ................................................. 73
Canadian warranty information ...................... 74
Recording a TV program ................................ 39
One-touch Timer Recording (OTR) ................ 41
Timer recording .............................................. 42
Other functions (VCR)
Stereo recording and playback ...................... 44
Second Audio Program (SAP) ........................ 44
Duplicating a video tape ................................. 45
Recording a DVD/CD disc .............................. 46
9
2I40301A-En_p02-13
9
21/3/06, 9:41 AM
Introduction
Identification of controls
See the page in
for details.
Front panel
VCR/DVD mode selector
button %
ON/STANDBY button
%
Cassette loading slot 34
EJECT
button 34
DVD mode indicator "%
REC button !'
FWD button !#
Disc tray "%
Remote sensor !
VCR mode indicator
CHANNEL
Display window 11
AUDIO (L/R)/VIDEO IN
(LINE IN 2) jacks "#
Rear panel
DVD COAXIAL DIGITAL AUDIO OUT jack
DVD S-VIDEO OUT jack
HDMI OUT jack
AC power cord
#
%
PLAY button !#
buttons !'
/
"
$
REV button !#
STOP button !#
DVD/VCR common AUDIO
(L/R)/VIDEO OUT jacks DVD AUDIO (L/R)
DVD COMPONENT
OUT jacks OUT jacks DVD OPTICAL DIGITAL
"
ANT IN jack $
ANT OUT jack $
AUDIO (L/R)/VIDEO
IN (LINE IN1) jacks "#
10
10
USB Port
When connecting the optical digital cable, remove
the cap and fit the connector into the jack firmly.
When not using the jack, keep the cap inserted
to protect it from dust intrusion.
AUDIO OUT jack
2I40301A-En_p02-13
OPEN/CLOSE button "%
21/3/06, 9:41 AM
Display window
Play indicator
Still indicator
DVD disc inserted indicator
Recording
indicator
(VCR)
Introduction
VCR indicator (VCR)
CD inserted
indicator
Multifunctional indicator
Track indicator (CD)
Tape loaded indicator (VCR)
Progressive indicator
AM/PM indicator
(AM is not displayed)
Timer Recording indicator (VCR)
VCR operation status
Press CALL to display VCR operation status on the screen.
To cancel the display, press CALL again.
While watching TV
HI-FI STEREO
DAY OF THE WEEK
Recording :
CLOCK
STEREO AND
SECOND
AUDIO
PROGRAM
(SAP)
VCR Icons
While operating a tape
8 : 47AM MON
STEREO SAP
CH 125
CHANNEL
OPERATING
MODE
8 : 30AM MON
HI-FI
Rec/Pause :
Play :
AUTO REPEAT
00 : 00 : 00 SP
TAPE SPEED
REAL TIME COUNTER
STEREO
00 : 15 : 12 SP
TAPE IN
Stop :
Eject :
OUTPUT SELECTION
Disc operation status
Press DISPLAY, the status display of the disc will appear on the screen as follows.
To cancel the display, press DISPLAY again.
DVD
VCD
DISC OPERATION
TITLE NO.
ELAPSED
TIME
DVD
Title 1/3
1/1 Eng Dolby Digital
1/1
ANGLE NO.
TOTAL
TIME
00:15:25 01:41:39
Chapter 2/24
1/2 Eng
DISC OPERATION
CHAPTER
NO.
ELAPSED TOTAL
TIME
TIME
VCD
Track 3/15
00:08:32 00:51:03
SUBTITLE LANGUAGE
TRACK NO.
AUDIO LANGUAGE
A KIND OF AUDIO
11
2I40301A-En_p02-13
11
21/3/06, 9:41 AM
Introduction
Identification of controls (Continued)
The instructions in this manual describe the functions on the remote control. See the page in
for details.
Remote control
DVD/VCR button 13
* POWER button 13
CABLE BOX button 15
* TV button 14
CALL button 11
* DISPLAY button 11
* CH
/
* Direct channel selection
buttons (0-9) 13
Number buttons (0-9) 14
button 14
ZERO RETURN button 37
JUMP button 50
* 100 button 14
* VOL +/- buttons 14
CM SKIP button 36
ZOOM button 50
* INPUT SELECT button 14
TOP MENU button 54 59
PROGRAM button 14
Direction buttons (
/ / / ) 13
SET+/- buttons 28
DVD
DVD MENU button 54 59
* ENTER button 28 63
CH+/- buttons 13
CANCEL button 31
CLEAR button 50
RETURN button 63 70
STOP button 35 47
PLAY button 35 47
FWD button 35 49
PAUSE/STILL button 36 48
SKIP
button 49
VISS + button 38
REV button 35 49
FWD
SKIP
button 49
VISS - button 38
SLOW button 36 49
VCR MENU button 28
SETUP button 63
CLOCK/COUNTER button 38
HDMI button 22
MARKER button 51
COUNTER RESET button 37
ANGLE button 54 59
USB
ATR button 36
SUBTITLE button 56
SP/SLP button 39
PLAYMODE button 52
AUDIO SELECT button 44
AUDIO button 55
DVD/VCR SELECT button 27 47
TV/VCR button 27
REC/OTR button 39 41
TIMER REC button 42
DVD/USB button 58
A-B RPT button 52
EJECT button (VCR) 34
OPEN/CLOSE (DVD) 47
DVD MENU button
Use the MENU button to display the menu included on
many DVD video discs. To operate a menu, follow the
instructions in “DVD Menu.” #"
*TV control buttons
The various brands of TV listed on page 14 can be operated
with this remote control. There may be some TV models that
cannot be operated with this remote control. If this is the case,
use the original remote control supplied with the TV.
•CABLE BOX control buttons
The various brands of CABLE BOX listed on page 15 can
be operated with this remote control. There may be some
CABLE BOX models that cannot be operated with this
remote control. If this is the case, use the original remote
control supplied with the CABLE BOX.
12
2I40301A-En_p02-13
12
21/3/06, 9:42 AM
Introduction
Inserting batteries
1
Open the battery compartment cover in the direction of
the arrow.
2
Install two “AAA” batteries
(supplied), paying attention to the
polarity diagram in the battery
compartment.
3
Replace the compartment
cover.
Caution:
Never throw batteries into a fire.
Notes:
• Be sure to use AAA size batteries.
• Dispose of batteries in a designated disposal area.
• Batteries should always be disposed of with the environment in mind. Always dispose of batteries in accordance with
applicable laws and regulations.
• If the remote control does not operate correctly, or if the operating range becomes reduced, replace batteries with
new ones.
• When necessary to replace batteries in the remote control, always replace both batteries with new ones. Never mix
battery types or use new and used batteries in combination.
• Always remove batteries from remote control if they are dead or if the remote control is not to be used for an
extended period of time. This will prevent battery acid from leaking into the battery compartment.
Remote control basics
• Press DVD/VCR to operate the DVD/VCR.
• Press POWER to turn the DVD/VCR on or off.
• Select your desired operating mode (DVD or VCR) using DVD/VCR SELECT.
(DVD or VCR indicator on the front panel will show you which mode is selected.)
• Press CH + or CH – to move through the channels one channel at a time.
• The / / / are also used to navigate on-screen menu system.
• You can directly access specific channels using Direct channel selection buttons (0–9).
• Each press of DVD/VCR SELECT on the remote control, switches the screen between the VCR screen (VCR mode)
and the DVD screen (DVD mode).
Operation
• Aim the remote control at the remote sensor and press control buttons to
operate.
• Operate the remote control within 30° angle on either side of the remote
sensor, up to a distance of approx. 7 meters.
Approx. 7 meters
13
2I40301A-En_p02-13
13
21/3/06, 9:42 AM
Introduction
POWER
TV
0–9
100
DISPLAY
INPUT SELECT
PROGRAM
VOL +/–
ENTER
?
CH M/?
Multi brand remote control
This remote control can be compatible with various brands of TV/
Cable box/DSS® satellite receiver by setting their control codes. The
TOSHIBA code has initially been set to control TOSHIBA TVs.
Setting TV control codes
1
2
Press TV to set the remote control operating
your TV.
While holding down PROGRAM, enter the two
digits of your TV's brand code (listed on the
right) using Number buttons (0–9), then release
PROGRAM.
Point the remote control at your TV and use each button
listed below to make sure that your TV is operated
correctly.
POWER
?
CH M/?
VOL +/–
INPUT SELECT
Direct channel
selection buttons
(0-9)
100
DISPLAY
ENTER
To turn the TV on or off.
To select TV channels in the upper
or lower direction.
To adjust the sound level.
To select an external source such
as a VCR.
To select TV channels. When selecting channels 1 to 9, first enter 0 and
then desired number.
To substitute for 100 channel key.
To turn TV’s screen display on or
off.
To use for the TV’s ENTER key.
Important
Some TV’s may not respond to all the operations above,
or may not be operated at all with this remote control. In
this case, operate your TV with its own remote control.
Table of TV brand codes
Brand name
of your TV
Brand Code
Brand name
of your TV
Brand Code
Toshiba
01
Penney
01, 02, 07, 11, 12
Bell & Howell
09
Philco
10
Carver
10
Philips
10
Celebrity
03
Pioneer
16
Citizen
12
Princeclub
12
Curtis Mathes 09, 12
Prism
07
Dumont
14
Proscan
02
Electro band
03
Proton
11
Emerson
09,11
Pulser
14
Fisher
09
Quasar
07, 15
GE
02, 07, 11
Radio Shack
13
Gibralter
14
RCA
02
Goldstar
11
Realistic
09, 11, 13
Hallmark
11
Runco(NEC)
14
Hitachi
06
Samsung
11, 12
Infinity
10
Sanyo
09
JBL
10
Scotch
11
JCB
03
Scott
11
JVC
05
Sears
01, 02, 09, 10, 11
LXI
01, 02, 09, 10, 11
Sharp
08, 13
Magnavox
10
Sony
03
Marantz
10
Soundesign
11
Megatron
06, 11
Supreme
03
Memorex
04, 09, 11
Sylvania
10
MGA
04, 11
Tandy
08
Midland
02,07, 14
Technics
07, 15
Mitsubishi
04, 11
Techwood
07
Motorola
08
Teknika
04,10,12
MTC
12
TMK
11
NAD
01, 11
Victor
05
Nikko
11
Vidikron
10
Optimus
09
Vidtech
11
Optonica
08
Wards
10, 11,13
Panasonic
07, 10, 15
Zenith
14
Notes:
• For some brands, several control codes (brand codes) are allocated. Try each of them until the buttons work on your TV.
• If you replace the remote control’s batteries, set the brand code
again.
14
2I40301A-En_p14-17
14
21/3/06, 9:42 AM
Setting Cable box/DSS® satellite
receiver control codes
1
Press CABLE BOX to set the remote control
operating your Cable box/DSS® satellite receiver.
Table of Cable box brand codes
Brand name of
your cable box
Toshiba
Anvision
2
While holding down PROGRAM, enter the two
digits of your Cable box/DSS® satellite receiver
brand code (listed on the right) using Number
buttons (0–9), then release PROGRAM.
Cablestar
Cableview
Citizen
Curtis
Diamond
Point the remote control at your Cable box/DSS®
satellite receiver and use each button listed below to
make sure that your Cable box/DSS® satellite receiver
is operated correctly.
To turn the Cable box/DSS® satellite receiver on or off.
?
CH M/?
To select cable/satellite channels in
the upper or lower direction. (Not
applicable to some brands of cable
box/satellite receiver.)
Number buttons (0–9) To select desired channels to record.
ENTER
To use for the Cable box’s ENTER key.
POWER
Eagle
Eastern
GC Brand
Gemini
General
Instrument
Hamlin
(Some cable boxes require you to use 100 button as the
enter button.)
Important
Some Cable box/DSS® satellite receiver may not respond
to all the operations above, or may not be operated at all
with this remote control. In this case, operate them with
its own remote control.
Notes:
• For some brands, several control codes (brand codes) are allocated. Try each of them until the buttons work on your Cable
box/DSS® satellite receiver.
• If you replace the remote control’s batteries, set the brand code
again.
Hitachi
Jerrold
Macom
Magnavox
Movietime
NSC
OAK
OAK Sigma
Panasonic
36
13, 20, 21,
22, 23, 24,
25, 26, 58,
62, 84
1, 20, 21,
29, 42, 44,
63, 88, 91
13, 20, 21,
22, 23, 24,
25, 26, 58,
62, 84
30, 42, 44,
52, 63, 88
30, 42, 44,
52, 63, 88
8, 9, 56, 61
1, 20, 21,
29, 42, 44,
63, 88, 91
13, 20, 21,
22, 23, 24,
25, 26, 58,
62, 84
26, 28
30, 42, 44,
52, 63, 88
4, 30, 85
1, 2, 3,
4, 31, 34,
55, 83, 85,
91
14, 15, 28,
41
31, 79, 80
1, 2, 3,
4, 31, 34,
55, 85, 91
31, 79, 80
13, 20, 21,
22, 23, 24,
25, 26, 58,
62, 84
29, 32, 38,
39, 42, 44,
88
29, 32, 38,
39, 42, 44,
88
10, 11, 12,
13, 46
10, 11, 12,
13, 46
6, 8, 16, 17
Brand name of
your cable box
Philips
Brand Code
4, 13, 20,
21, 22, 23,
24, 25, 26,
58, 62, 84
Pioneer
5, 6, 78
Pulsar
30, 42, 44,
52, 63, 88
Randtek
13, 20, 21,
22, 23, 24,
25, 26, 58,
62, 84
RCA
6, 8, 16, 17
Realistic
44, 88
Regal
14, 23, 41,
84
Regency
26, 28
Rembrandt
29, 32, 38,
39, 42, 44,
88
Samsung
4, 6, 32,
42, 78
Scientific Atlanta 8, 9, 56, 61
Sheritech
27
SL Mark
4, 6, 32,
42, 78
Sprucher
6, 8, 16, 17
Stargate
4, 6, 30, 32,
42, 44, 52,
63, 78, 88
Sylvania
19
Teknika
74
Telecaption
77
Teleview
4, 6, 32,
42, 78
Texscan
18, 19
Tocom
1, 33, 34,
42, 48, 49,
73, 91
Unica
1, 20, 21,
29, 42, 44,
63, 88, 91
Universal
29, 42, 43,
44, 52, 63,
82, 88
Videoway
7, 23, 45,
50, 84
Viewstar
13, 20, 21,
22, 23, 24,
25, 26, 58,
62, 84
Warner Amex 6
Zenith
7, 23, 45,
50, 84
Introduction
Archer
Brand Code
Table of DSS® satellite receiver brand codes
Brand name
Toshiba
RCA
Sony
Magnavox
Brand code
99
98
97
95, 96
Brand name
Draker
Primestar
Hitachi
Panasonic
Brand code
94
93
92, 89
90
15
2I40301A-En_p14-17
15
21/3/06, 9:42 AM
Connections
Antenna connections
If you are using an antenna system, follow these instructions. If you are a Cable TV subscriber, skip ahead to page
for the proper connections.
&
Antenna to DVD/VCR connection
The DVD/VCR must be connected “between” the antenna and the TV. First, disconnect the antenna from the TV and
connect it to the DVD/VCR. Then connect the DVD/VCR to the TV. Below are 3 common methods of connecting an
antenna system to a DVD/VCR. Find the type of antenna system you are using and follow the connection diagram.
1
Combination VHF/UHF Antenna with 75 ohm Coaxial Cable
DVD/VCR
75 ohm Coaxial Cable
2
Combination VHF/UHF Antenna with 300 ohm Twin Lead (Flat) Wire
DVD/VCR
Matching Transformer 300 ohm Input 75
ohm output (not supplied)
300 ohm Twin Lead (Flat) Wire
(not supplied)
3
DVD/VCR
Separate VHF and UHF Antennas
UHF
VHF
Combiner 75/300 ohm Inputs 75 ohm output
(not supplied)
300 ohm Twin Lead (Flat) Wire
(not supplied)
75 ohm Coaxial Cable
Note: If both VHF and UHF antennas have 300 ohm twin lead (flat) wires, use a combiner having two 300 ohm inputs and
one 75 ohm output.
Notes: • A clear picture will not be obtained by the DVD/VCR unless the antenna signal is good. Connect the antenna to the
DVD/VCR properly.
• For better quality recording, an indoor antenna or a telescopic antenna is not recommended. The use of an outdoor
type antenna is required.
• If you are not sure about the connection, please refer to qualified service personnel.
16
2I40301A-En_p14-17
16
21/3/06, 9:42 AM
DVD/VCR to TV connection
After you have connected the antenna to the DVD/VCR, you must connect the DVD/VCR to the TV.
Below are 3 common methods of connecting your DVD/VCR to a TV. Find the type of TV you are using and follow the
connection diagram.
This DVD/VCR has a single 75 ohm output for connection to a TV. If your TV has separate VHF and UHF antenna
inputs (numbers 2 and 3 below), use a splitter to connect the DVD/VCR to the TV for VHF and UHF reception.
Connections
TV
Note:
VHF/UHF IN
If a VHF or UHF antenna is used,
set the TV/CABLE menu option to
the “TV” mode.
75 ohm Coaxial Cable (supplied)
TV with single 75 ohm VHF/UHF antenna
input
TV
Note:
75 ohm Coaxial Cable
(supplied)
Splitter 75 ohm Input
75/300 ohm outputs
(not supplied)
UHF
If a VHF or UHF antenna is used,
set the TV/CABLE menu option
to the “TV” mode.
VHF
TV with 300 ohm UHF and 75 ohm VHF
antenna inputs
TV
UHF
75 ohm Coaxial Cable
(supplied)
Splitter 75 ohm Input
300 ohm outputs
(not supplied)
Note:
If a VHF or UHF antenna is used,
set the TV/CABLE menu option to
the “TV” mode.
VHF
TV with 300 ohm UHF and 300 ohm VHF
antenna inputs
17
2I40301A-En_p14-17
17
21/3/06, 9:42 AM
Connections
Cable TV connections
Many cable companies offer services permitting reception of extra channels including pay or subscription channels. This
DVD/VCR has an extended tuning range and can be tuned to most cable channels without using a cable company
supplied converter box, except for those premium channels which are intentionally scrambled. If you subscribe to a
premium channel which is scrambled, you must have a descrambler box for proper reception.
1
DVD/VCR
TV
VHF/UHF
IN (ANT)
Incoming Cable
Allows: * Recording of nonscrambled channels.
* Use of the programmable timer.
* Recording of one channel while watching another.
DVD/VCR
2
TV
Converter/
Descrambler
VHF/UHF
IN (ANT)
Incoming
Cable
Allows: * Recording of channels through the converter box
(scrambled and unscrambled).
* Using the programmable timer to record only the
channel selected at the converter box.
Note:
To record from converter/descrambler, DVD/
VCR tuner must be tuned to the converter
output channel, usually channel 3 or 4.
Prevents: * Recording one channel while watching another.
* Using the DVD/VCR tuner to select channels.
3
DVD/VCR
TV
Converter/Descrambler
VHF/UHF
IN (ANT)
Incoming Cable
Allows: * Recording of nonscrambled channels.
* Use of the programmable timer.
* Recording an unscrambled channel while watching
any channel selected at the converter box.
Prevents:
Recording scrambled channels.
Note:
If you are playing a tape or using the tuner
built into the DVD/VCR, the converter must
be set to the video channel output of the DVD/
VCR (either 3 or 4).
Note: Whenever a Converter/Descrambler box is placed before the DVD/VCR, you must tune the DVD/VCR to the output of
the Converter/Descrambler box, usually channel 3 or 4.
18
2I40301A-En_p18-27
18
21/3/06, 9:42 AM
IMPORTANT: Make sure the TV/CABLE menu option is set to the “CABLE” mode.
This DVD/VCR cannot receive scrambled programs since it does not contain a descrambler. In order to receive scrambled programs, your existing descrambler must be used. Descrambler boxes are available from cable companies. Consult your local cable company for more information concerning connection to their descrambler equipment. There are
many ways to connect your DVD/VCR to a cable system. Below are six common methods of connection.
TV
Splitter
A/B Switch
VHF/UHF
IN (ANT)
A
B
Incoming Cable
Connections
4
DVD/VCR
Converter/Descrambler
Allows: *
*
*
Prevents: *
Recording of one channel while watching another.
Using the programmable timer to record only the channel selected at the converter box.
Recording of all channels through the converter box.
Watching scrambled channels while recording another channel.
Using
the DVD/VCR tuner to select channels.
*
DVD/VCR
5
TV
Splitter
Converter/Descrambler
Incoming Cable
A/B Switch
VHF/UHF
IN (ANT)
A
B
Allows: *
*
*
*
Prevents:
Recording of nonscrambled channels.
Recording of one channel while watching another.
Watching premium channels through the converter while recording nonscrambled channels.
Using the programmable timer.
Recording scrambled channels.
DVD/VCR
6
TV
Splitter
Converter/Descrambler
VHF/UHF
IN (ANT)
Converter/Descrambler
Incoming Cable
A/B Switch
A
B
Allows: * Recording of all channels through the converter box.
* Recording a scrambled or unscrambled channel while watching another (scrambled or
unscrambled) channel.
* Using the programmable timer to record only the channel selected at the converter box.
Prevents: Using the DVD/VCR tuner to select channels.
19
2I40301A-En_p18-27
19
21/3/06, 9:42 AM
Connections
Connecting to a TV
Connect the DVD/VCR to your TV.
Note: This method transports VHS and DVD-video signals. For enhanced DVD-video performance, we recommend you to
connect the S-video or ColorStream® component video outputs to your TV/monitor also. Basic connection
Signal flow
(yellow) (red)
To wall outlet
To VIDEO
OUT
(white)
To ANALOG AUDIO OUT
Audio/video cable (supplied)
To audio inputs
To video input
(yellow)
(red)
(white)
• Make sure following setting.
On-screen display
Select:
Page
“Digital Out”
“PCM” or “Bitstream”
$%
TV or monitor with
audio/video inputs
Notes:
• Refer to the owner’s manual of the connected TV as well.
• When you connect the DVD/VCR to your TV, be sure to turn off the power and unplug both units from the wall outlet before
making any connections.
• If your television set has one audio input, connect the left and right audio outputs of the DVD/VCR to a Y cable adapter
(not supplied) and then connect to your TV.
• Connect the DVD/VCR directly to your TV. If you connect the DVD/VCR to a VCR, TV/VCR combination or video selector,
the playback picture may be distorted as DVD video discs are copy protected.
• While HDMI is being output in the DVD mode, it is impossible to output from the Video out jack, S-video out jack or
Component video out jacks.
20
2I40301A-En_p18-27
20
21/3/06, 9:42 AM
S-video output
An S-Video connection is superior to Video (Yellow) output. Use this method for DVD playback when the connected television has SVideo input, and does not have component video inputs.
Component video outputs
Connecting to an audio system and TV equipped with S-video input/component video inputs
Connections
PROGRESSIVE outputs
Some TVs or monitors are equipped with component video inputs that are capable of reproducing a progressively scanned video
signal. Connecting to these inputs allows you to view the highest quality pictures with less flicker.
INTERLACED outputs
Some TVs or monitors are equipped with component video inputs. Connecting to these inputs allows you to enjoy the highest quality
DVD picture playback.
Notes:
• To switch the scan mode between the interlace and progressive modes, see page 69 .
• In some TVs or monitors, the color levels of the playback picture may be reduced slightly or the tint may change. In such a case,
adjust the TV or monitor for optimum performance.
The S-video output and component video output transports the DVD-video signal exclusively and will deliver enhanced DVD
video picture performance.
Signal flow
To ANALOG
AUDIO OUT
(white)
To S-VIDEO
OUT
(red)
If you connect the DVD/VCR to
your TV with the DVD OUT jacks,
select the corresponding video
input on your television to watch
DVD video discs.
To wall outlet
S-video cable
(not supplied)
• Actual
labels for
component
video inputs
may vary
depending
on the TV
manufacturer (ex. Y,
R-Y, B-Y or
Y, CB, CR).
To PR/CR
VIDEO
OUT
To PB/CB
VIDEO
OUT
To Y
VIDEO
OUT
Audio cable (not supplied)
To Y video input
To audio inputs of
the amplifier
(red)
(white)
To PB/CB video input
Component
video cable
(not supplied)
To PR/CR video input
To S-video input TV or monitor with
component video inputs
• Make sure following setting.
On-screen display
Select:
Page
“Digital Out”
“PCM” or “Bitstream”
$%
Audio system
Notes:
• Refer to the owner’s manual of the connected equipment as well.
• When you connect the DVD/VCR to other equipment, be sure to turn off the power and unplug all of the equipment from
the wall outlet before making any connections.
• If you place the DVD/VCR near a tuner or radio, the radio broadcast sound might be distorted. In this case, place the DVD/
VCR away from the tuner and radio.
• The output sound of the DVD/VCR has a wide dynamic range. Be sure to adjust the receiver’s volume to a moderate
listening level. Otherwise, the speakers may be damaged by a sudden high volume sound.
• Turn off the amplifier before you connect or disconnect the DVD/VCR’s power cord. If you leave the amplifier power on, the
speakers may be damaged.
• While HDMI is being output in the DVD mode, it is impossible to output from the Video out jack, S-video out jack or
Component video out jacks.
• When connecting to a TV using the S-video jack, make sure that the Progressive indicator “ ” on the display
window is not lit. If it is lit, the S-video outputs do not feed the correct signals and you cannot see any picture. To
turn off the Progressive indicator, select Interlaced output 69 .
21
2I40301A-En_p18-27
21
21/3/06, 9:42 AM
Connections
Connecting to a TV (Continued)
About HDMI
HDMI (High Definition Multimedia Interface) supports both video
and audio on a single digital connection for use with DVD players,
DTV, set-top boxes, and other AV devices. HDMI was developed
to provide the technologies of High Bandwidth Digital Content
Protection (HDCP) as well as Digital Visual Interface (DVI) in one
specification. HDCP is used to protect digital content transmitted
and received by DVI-compliant or HDMI-compliant displays.
HDMI has the capability to support standard, enhanced, or highdefinition video plus standard to multi-channel surround-sound
audio. HDMI features include uncompressed digital video, a
bandwidth of up to 2.2 gigabytes per second (with HDTV signals),
one connector (instead of several cables and connectors), and
communication between the AV source and AV devices such as
DTVs.
HDMI, the HDMI logo and High-Definition Multimedia Interface are
trademarks or registered trademarks of HDMI licensing LLC.
Connecting to a display (Using the HDMI cable)
Signal flow
To wall outlet
For proper operation, it is recommended
that you use as short an HDMI cable as
possible.
To HDMI OUT
HDMI Cable (not supplied)
Switching the video quality (HDMI mode) using HDMI
button on the remote control
Press HDMI on the remote control to receive a suitable
video quality. The video quality is required to match
your TV having HDMI feature and suitable quality.
Please also check your TV owner's manual.
Press HDMI to change the video quality as follows:
HDMI: Off
To HDMI input
HDMI-compatible display
• Make sure following setting.
On-screen display
Select:
Page
“Digital Out”
“PCM”
$%
HDMI: cannot output
Component/Composite/S-Video: outputting
(Output setup is set to Progressive : cannot output S-Video)
NTSC: 480p (Progressive)
NTSC: 720p (Progressive)
HDMI: outputting
Component/Composite/S-Video: cannot output
NTSC: 1080i (Interlace)
Notes:
It is only possible to switch the HDMI output in the following below cases unless only an Audio/Video Cable/S-video cable/
Component Video Cables is connected.
* When in DVD Mode (in DISC/USB Mode)
* When the disc is in Stop or Resume mode
* When the Setup Menu is not being displayed
* When the HDMI Cable is connected
22
2I40301A-En_p18-27
22
21/3/06, 9:42 AM
Connections
The content of the output for each output jack are as shown in the following table and differ depending on User settings/operation.
USER setting/operation
HDMI
Mode
Output
VCR/DVD
*1
Off
VCR
DVD
480p
720p
1080i
480p
720p
1080i
Content of output for each output jack
Output
Setting
HDMI
Interlace
Progressive
-
Interlace
Progressive
Interlace
Progressive
Off
480p
720p
1080i
480p
720p
1080i
Interlace
Progressive
480p (DVD)
720p (DVD)
1080i (DVD)
480p (DVD)
720p (DVD)
1080i (DVD)
-
Video
S-Video
Component
DVD
-
480i (DVD)
480p (DVD)
-
-
-
-
DVD
DVD
DVD
-
480i (DVD)
480p (DVD)
-
-
-
-
-
-
VCR
480p (DVD)
720p (DVD)
1080i (DVD)
480p (DVD)
720p (DVD)
1080i (DVD)
RF
Modulator
VCR
DVD
-
*1: Settings for HDMI output format are performed using the “HDMI” key on the remote control.
3 Picture Output
• DVD Mode
The following refers to instructions for Picture Output in DVD Mode.
There is no Analog Output (*2) for HDMI output.
When HDMI output setting is “Off”, there is no HDMI output.
*2: Output from Video out jack/S-Video out jack/Component out jacks
• VCR Mode
The following refers to instructions for Picture Output in VCR mode.
This set outputs the picture from the Video out jack in VCR mode. However, please see the following instructions for HDMI out
jack/S-Video out jack/Component out jacks.
<During HDMI Output>
DVD picture is always output from HDMI out jack during HDMI Output, but it cannot output from S-Video out jack/Component out
jacks during HDMI Output.
<When HDMI Output setting is “Off”>
When the HDMI output setting is “Off”, this set outputs picture signals as follows according to the HDMI Setting in the Setup
Menu. When HDMI Output setting is “Off”, HDMI output does not function.
When the Output setting is “Interlace”: Picture from VCR is output from the Video out jack
Picture from the DVD is output from the S-Video out jack/Component out jacks
When Output setting is “Progressive”:
Picture from VCR is output from the Video out jack
NO OUTPUT from the S-Video out jack
Picture from the DVD is output from the Component out jacks
Notes:
• When in DVD Mode/outputting HDMI signal, it is impossible to output any video images from either the Video out jack/S-Video
out jack/Component out jacks.
If the viewer would like to view videos using the Video out jack/S-Video out jack/Component out jacks, then the HDMI output must
set to “Off” by pressing the HDMI button on the remote control.
• When the HDMI Cable is connected, if the HDMI is pressed or the VCR Mode is switched to DVD Mode, there is a possibility that
the monitor will not show any output images. In this case, turn off the HDMI mode.
Deactivate HDMI output with HDMI (For details, please refer to “Switching the video quality (HDMI mode) using HDMI
button on the remote control”
).
• Refer to the Owner’s manual of the connected TV as well.
• When connecting the DVD/VCR to your TV, be sure to turn off the power and unplug both units from the wall outlet before making any
connections.
• If you have an HDMI (with HDCP) equipped monitor or display, you can connect it to the DVD/VCR using the HDMI cable.
• The HDMI connector outputs uncompressed digital video as well as almost every kind of digital audio that the DVD/VCR is compatible
with, including DVD-Video, Video CD, Audio CD and MP3/WMA/JPEG/DivX® files.
• No sound will be output from the HDMI cable if the “Digital Out” is not set to “PCM” $% .
23
2I40301A-En_p18-27
23
21/3/06, 9:42 AM
Connections
Connecting to an audio equipment
You can enjoy high quality dynamic sounds of DVD video discs or
audio CDs by connecting the DVD/VCR to optional audio
equipment.
For connection to your TV, see “Connecting to a TV”
.
• This selection uses the following reference mark.
: Front speaker
: Rear speaker
: Sub woofer
: Center speaker
: Signal flow
Connecting to an amplifier equipped with a Dolby® Digital decoder
Dolby Digital
Dolby Digital is the surround sound technology used in theaters showing the latest movies, and is
now available to reproduce this realistic effect in the home. You can enjoy motion picture and live
concert DVD video discs encoded via the Dolby Digital recording system with this dynamic realistic
sound by connecting the DVD/VCR to a 6 channel amplifier equipped with a Dolby Digital decoder
or Dolby Digital processor. If you have a Dolby Pro Logic Surround decoder, you will obtain the full
benefit of Pro Logic from the same DVD movies that provide full 5.1-channel Dolby Digital soundtracks,
as well as from titles with the Dolby Surround mark.
Amplifier equipped with a
Dolby Digital decoder
To COAXIAL
type digital
audio input
To OPTICAL
type digital
audio input
Manufactured under license from
Dolby Laboratories. “Dolby”, “Pro
Logic” and the double-D symbol are
trademarks of Dolby Laboratories.
• Use DVD video discs
encoded via the Dolby Digital
recording system.
• Make sure following setting.
On-screen display
“Digital Out”
Optical cable (not supplied)
Select:
Page
“PCM” or
$%
“Bitstream”
Connect either
75 Ω coaxial cable (not supplied)
Connecting to an amplifier equipped with Dolby Surround Pro Logic
Dolby Surround Pro Logic
You can enjoy the dynamic realistic sound of Dolby Surround Pro Logic by connecting an amplifier and speaker system (right and left
front speakers, a center speaker, and one or two rear speakers).
With an amplifier equipped with Dolby Digital
Connect the equipment the same way as described in “Connecting to an amplifier
equipped with a Dolby Digital decoder.” Refer to that amplifier’s owner’s manual and set
the amplifier so that you can enjoy Dolby Surround Pro Logic sound.
• Make sure following setting.
On-screen display
With an amplifier not equipped with Dolby Digital
Connect the equipment as follows.
• This connection is only suitable for Video CDs and
Audio CDs.
*
“Digital Out”
Select:
Page
“PCM” or $%
“Bitstream”
* Connect one or two rear speakers.
The output sound from the rear
speakers will be monaural even if you
connect two rear speakers.
Amplifier equipped with
Dolby Surround Pro Logic
To audio input
To ANALOG
AUDIO OUT
Audio cable (not supplied)
Connecting to an amplifier equipped with a DTS decoder
Digital Theater Systems (DTS)
DTS is a high quality surround technology used in theaters and now available for home use,
on DVD video discs or audio CDs.
If you have a DTS decoder or processor, you can obtain the full
benefit of 5.1 channel DTS encoded sound tracks on DVD
video discs or audio CDs.
Amplifier equipped with a
DTS decoder
To COAXIAL
type digital
audio input
To OPTICAL
type digital
audio input
“DTS” and “DTS Digital Out” are
trademarks of Digital Theater Systems,
Inc.
• Use DVD video discs or
audio CDs encoded via the
DTS recording system.
• Make sure following setting.
On-screen display
“Digital Out”
Optical cable (not supplied)
Connect either
75 Ω coaxial cable (not supplied)
24
2I40301A-En_p18-27
24
21/3/06, 9:42 AM
Select:
Page
“Bitstream” $%
Warning
When playing DTS-encoded discs (DVD video discs and audio CDs), excessive noise may be output from the analog stereo
jacks. To avoid possible damage to the audio system, you should take proper precautions when the ANALOG AUDIO OUT (L/
R) jacks of the DVD/VCR are connected to an amplification system. (Do not leave the ANALOG AUDIO OUT (L/R) wires
dangling.) To enjoy DTS Digital Surround™ playback, an external 5.1 channel DTS Digital Surround™ decoder system must
be connected to the OPTICAL or COAXIAL DIGITAL AUDIO OUT jack of the DVD/VCR.
Connecting to an amplifier equipped with an MPEG2 audio decoder
Amplifier equipped with an
MPEG2 audio decoder
To OPTICAL
type digital
audio input Optical cable (not supplied)
To COAXIAL
type digital
audio input
75 Ω coaxial cable (not supplied)
• Use DVD video discs
encoded via the MPEG2
recording system.
• Make sure following setting.
Select:
On-screen display
“Digital Out”
Connections
MPEG2 sound
You can enjoy motion picture and live concert DVD video discs encoded via the MPEG2 recording system with dynamic realistic sound
by connecting an amplifier equipped with an MPEG2 audio decoder or MPEG2 audio processor.
Page
“PCM” or $%
“Bitstream”
Connect either
Connecting to an amplifier equipped with a digital audio input
2 channel digital stereo
You can enjoy the dynamic sound of 2 channel digital stereo by connecting an amplifier equipped with a digital audio input and speaker
system (right and left front speakers).
• Make sure following setting.
On-screen display
Amplifier equipped with a
digital audio input
To OPTICAL
type digital
audio input Optical cable (not supplied)
To COAXIAL
type digital
audio input
“Digital Out”
Select:
Page
“PCM” or
$%
“Bitstream”
Connect either
75 Ω coaxial cable (not supplied)
Notes:
• DO NOT connect the OPTICAL or COAXIAL DIGITAL AUDIO OUT jack of the DVD/VCR to the AC-3 RF input of a Dolby
Digital Receiver. This input on your A/V Receiver is reserved for Laserdisc use only and is incompatible with the OPTICAL or
COAXIAL DIGITAL AUDIO OUT jack of the DVD/VCR.
• Connect the OPTICAL DIGITAL AUDIO OUT jack of the DVD/VCR to the “OPTICAL” input of a Receiver or Processor.
• Connect the COAXIAL DIGITAL AUDIO OUT jack of the DVD/VCR to the “COAXIAL” input of a Receiver or Processor.
• Refer to the owner’s manual of the connected equipment as well.
• When you connect the DVD/VCR to other equipment, be sure to turn off the power and unplug all of the equipment from the
wall outlet before making any connections.
• The output sound of the DVD/VCR has a wide dynamic range. Be sure to adjust the receiver’s volume to a moderate
listening level. Otherwise, the speakers and your hearing may be damaged by a sudden high volume sound.
• Turn off the amplifier before you connect or disconnect the DVD/VCR’s power cord. If you leave the amplifier’s power on, the
speakers may be damaged.
25
2I40301A-En_p18-27
25
21/3/06, 9:42 AM
Connections
Connecting to a USB Mass Storage
This unit can be used to read JPEG, WMA, MP3 and DivX® data for any memory card reader/writer or digital camera that
accepts USB Mass Storage Class.
For devices that are compatible with the unit’s USB port, please refer to page 8 .
Connecting to a USB Mass Storage
Signal flow
To USB port
USB Mass Storage
USB Cable (not supplied)
Notes:
In order to avoid damage to the unit, the USB Mass Storage, the Memory Card, etc, the following instructions should
be observed.
• Insert the USB cable properly taking care to observe the correct port direction.
• Make sure the unit is off or is set to DISC mode #& when disconnecting the USB Mass Storage from the unit.
• In order to avoid damage to recorded data, do not plug in or unplug the unit, no matter whether the USB Mass
Storage is On or Off, including Resume Stop mode.
• In order to avoid damage to recorded data, do not disconnect the USB Mass Storage from the port, no matter
whether the USB Mass Storage is On or Off, including Resume Stop mode.
• Before removing the Memory Card while a Memory Card Reader or Digital Camera is connected to the unit, ensure
that the power is off or that the unit is in DISC mode #& .
• Do not remove the Memory Card from the Memory Card Reader or Digital Camera no matter whether the Memory
Card is On or Off, including Resume Stop mode.
• In order to avoid damage to recorded data, do not plug in or unplug the unit, no matter whether the Memory Card
is inserted or not inserted into the Memory Card Reader or Digital Camera, including Resume Stop mode.
• In order to understand the correct operation and handling of the USB Mass Storage, read the USB Mass Storage
instructions carefully.
• As it cannot be guaranteed that recorded data will not be damaged while using this unit, it is recommended to
make back-up data.
• Avoid connecting any other USB connectable device that uses electricity from the USB connector such as a Printer
or Keyboard when the USB Mass Storage is connected.
• It is impossible to connect several devices by using a USB HUB.
26
2I40301A-En_p18-27
26
21/3/06, 9:42 AM
Basic setup (VCR)
POWER
DVD/VCR
3
4
Setting the video channel
When a TV is connected with the 75 ohm coaxial cable only.
To view playback of a recorded tape or DVD disc, or to watch a
program selected by the VCR's channel selector, the TV must be set to
channel 3 or 4 (video channel).
TV/VCR
DVD/VCR SELECT
Setting the video channel
Press DVD/VCR to operate the DVD/VCR.
2
Press and hold 3 or 4 on the remote for 3
seconds in standby mode.
The video channel will
start to flash for 3
seconds in the display
window.
OR
3
Press POWER on the remote control or
ON/
STANDBY on the unit to turn on the DVD/VCR.
4
Press DVD/VCR SELECT to select the VCR mode.
5
Turn ON the TV and set to CH 3 or 4 to correspond with the channel selected in step 2.
6
Press TV/VCR to select the VCR position.
7
Select any channel to receive a TV station in
your area.
The channel number will appear on the screen
for about 4 seconds.
For a push-button TV tuner
Basic setup (VCR)
1
If CH 3 or 4 corresponding to the video channel cannot
be tuned on your TV, proceed as follows: set the VCR
3/4 channel selector and the TV to CH 3 or 4, playback
a prerecorded tape and tune the TV to receive a sharp
color picture from the video cassette recorder. Refer to
your TV owner's manual for details.
Note:
If the unit does not operate properly, or No key operation
(by the unit and/or the remote control): Static electricity, etc.,
may affect the player's operation. Disconnect the AC power cord
once, then connect it again.
The VCR indicator on the
front panel will light.
The VCR indicator will
appear in the display
window.
27
2I40301A-En_p18-27
27
21/3/06, 9:42 AM
Basic setup (VCR)
DVD/VCR
Setting the language
You can choose from three different languages (English,
French and Spanish) for the on-screen display.
ENTER
SET +/–
VCR MENU
DVD/VCR SELECT
Setting the language
Preparation:
• Turn ON the TV and select to the corresponding
video input.
• Press DVD/VCR to operate the DVD/VCR.
• Press DVD/VCR SELECT to select the VCR mode.
(The VCR indicator will light.)
1
4
Press VCR MENU until the menu screen is
cleared.
Press VCR MENU.
The VCR menu screen will appear.
Press SET + or – to select “SYSTEM
SETUP”, then press ENTER.
If you use the unit for the first time,
press VCR MENU, instead of the
“SYSTEM SETUP” menu screen of
the main screen in step 2 may appear.
Notes:
• Both the VCR and the DVD have their own player menus 63 .
• If no buttons are pressed for more than 60 seconds, the VCR
MENU screen will return to normal TV-operation automatically.
〉
〈
2
Press SET + or – to select “LANGUAGE”, then
press ENTER.
〈 〉
3
Press SET + or – to select the desired language:
English (ENGLISH), Spanish (ESPAÑOL) or
French (FRANCAIS), then press ENTER.
〈 〉
28
2I40301A-En_p28-33
28
21/3/06, 9:43 AM
POWER
DVD/VCR
Clock setting
The AUTO CLOCK function will automatically set the built-in clock
(Month, Day, Year and Time) when the DVD/VCR is connected to an
Antenna or Cable system and it is turned off. The DVD/VCR searches for
a station in your area containing the necessary AUTO CLOCK setting
signals. Once received, it will take approximately 4 minutes for the clock
to set itself automatically.
CALL
ENTER
SET +/–
VCR MENU
DVD/VCR SELECT
AUTO CLOCK setting
To set AUTO CLOCK to off
• Turn ON the TV and select the corresponding video input.
• Press DVD/VCR to operate the DVD/VCR.
• Press DVD/VCR SELECT to select the VCR mode.
(The VCR indicator will light.)
1
2
3
Connect the Antenna or Cable system.
4
Wait at least three minutes and press POWER.
5
Press CALL to check the clock setting on
the on screen display.
Press VCR MENU.
• If you use a cable box, turn it on.
Plug the AC power cord to the AC outlet.
2
Make sure the DVD/VCR is turned off.
Press SET + or – to select “SYSTEM SETUP”,
then press ENTER.
• Depending on the reception
condition it may take approx. thirty
minutes.
• If you press POWER, the Auto
Clock set is not programmed.
8 : 47AM MON
STEREO SAP
3
Press SET + or – to select “AUTO CLOCK”.
4
Press ENTER to select “OFF”.
5
Press VCR MENU repeatedly to return to the
normal screen.
CH 125
00 : 00 : 00 SP
6
1
Basic setup (VCR)
When shipped from factory the AUTO CLOCK is set to “ON”.
But if you do not want AUTO CLOCK setting:
Preparation:
If the clock is not set, check the antenna
condition. The AUTO CLOCK may not
function properly if the reception condition
is not good.
AUTO CLOCK adjustment
The auto clock adjustment will be updated at 6:00
AM, 12:00 PM and 6:00 PM everyday when the DVD/
VCR turned off.
• If you use a cable box and you want AUTO CLOCK
adjustment to be performed, the cable box must be
left on.
• The AUTO CLOCK adjustment is not effective when
there is a difference of more than 5 minutes exists
between the built-in clock time and the actual time.
• When the AUTO CLOCK is set to
“OFF”, the AUTO CLOCK adjustment
does not function. Set the clock
manually ! .
29
2I40301A-En_p28-33
29
21/3/06, 9:43 AM
Basic setup (VCR)
Clock setting (Continued)
To set STANDARD TIME
To set DAYLIGHT SAVING TIME
In the rare event that you live within broadcast range of two You can set the DAYLIGHT SAVING TIME automatically or
stations in two different time zones, the DVD/VCR may recognize manually.
the wrong station for the AUTO CLOCK setting.
To correct the situation:
1
Press VCR MENU.
1
Press VCR MENU.
Press SET + or – to select “SYSTEM SETUP”,
then press ENTER.
2
Press SET + or – to select “SYSTEM SETUP”,
then press ENTER.
3
2
Press SET + or – to select “DAYLIGHT
SAVING TIME”, then press ENTER.
Press SET + or – to select “STANDARD TIME”,
then press ENTER.
〈 〉
4
Press SET + or – to select your time zone,
then press ENTER.
3
Press SET + or – to select one of the
options, then press ENTER. Press VCR
MENU until the MENU screen is cleared.
ON:
OFF:
ATLANTIC : GMT–4hours
EASTERN : GMT–5hours
CENTRAL : GMT–6hours
MOUNTAIN : GMT–7hours
PACIFIC
: GMT–8hours
ALASKA
: GMT–9hours
HAWAII
: GMT–10hours
AUTO
: AUTO SET
(GMT: Greenwich Mean Time)
5
AUTO:
for manual setting
(forward one hour)
for manual setting
(back one hour)
for automatic setting
(read XDS in the signal)
When you want to set the DAYLIGHT
SAVING TIME manually, on the first
Sunday in April you set to “ON”, and
on the last Sunday in October you set
to “OFF”.
Press VCR MENU until the menu screen is
cleared.
〈 〉
Notes:
Notes:
• When shipped from factory, the DAYLIGHT SAVING TIME is
• To be able to select the standard time, the clock must first be
set to “AUTO” position.
set by AUTO CLOCK once.
• When the clock is not set, DAYLIGHT SAVING TIME setting
• If you live in Newfoundland and the AUTO CLOCK does not
is not available.
function properly, set the AUTO CLOCK menu option to “OFF”
• When there is no DAYLIGHT SAVING TIME in your area, aland set the clock manually.
ways select “OFF” position in step 3.
30
2I40301A-En_p28-33
30
21/3/06, 9:43 AM
SET +/–
ENTER
CANCEL
If the AUTO CLOCK process did not set the date and time correctly, you
must set them manually for timer recording and DAYLIGHT SAVING TIME.
VCR MENU
Manual clock setting
1
Press VCR MENU.
2
Press SET + or – to select “SYSTEM SETUP”,
then press ENTER.
After setting the clock, date and time starts
functioning automatically.
8 : 30AM SAT
3
6
Basic setup (VCR)
EXAMPLE: Setting the clock to “8:30 AM” October, 28
(SAT), 2006.
To make corrections any time during the process
Press CANCEL repeatedly until the item you want to
change blinks, then press SET + or –.
Note:
After a power failure or disconnection of the power, the timer
settings will be lost. In this case, reset the present time.
Press SET + or – to select “CLOCK SET”,
then press ENTER.
〈 〉
4
Press SET + or – to set the month, then press
ENTER.
MONTH
DAY
10
1 (SUN)
YEAR
2006
TIME
12 : 00AM
〈+/–/ENTER/CANCEL/MENU 〉
5
Set the day, year and time as in step 4.
〈
〉
31
2I40301A-En_p28-33
31
21/3/06, 9:43 AM
Basic setup (VCR)
DVD/VCR
Tuner setting
This DVD/VCR is equipped with a channel memory feature which allows
channels to skip up or down to the next channel set into memory,
skipping over unwanted channels. Before selecting channels, they must
be programmed into the DVD/VCR’s memory. In addition to normal
VHF and UHF channels, this DVD/VCR can receive up to 113 Cable
TV channels. To use this DVD/VCR with an antenna, set the TV/CABLE
menu option to the TV mode. When shipped from the factory, this menu
option is in the CABLE mode.
TV/CABLE selection
VCR MENU
DVD/VCR SELECT
Setting channels automatically
Preparation:
• Turn ON the TV and select to the corresponding
video input.
• Press DVD/VCR to operate the DVD/VCR.
• Press DVD/VCR SELECT to select the VCR mode.
(The VCR indicator will light.)
1
ENTER
SET +/–
1
Repeat left step 1 and press SET + or – to
select “AUTO CH MEMORY”.
CH SETUP
TV CABLE
AUTO CH MEMORY
ADD/DELETE
Press VCR MENU. Press SET + or – to select
“CH SETUP”, then press ENTER.
〈+/-/ENTER/MENU 〉
2
Press ENTER.
Auto tuning will begin. The channel display will count up and when finished,
the screen returns to normal.
2
+0 Press SET + or – to select “TV/CABLE”.
CH SETUP
TV CABLE
AUTO CH MEMORY
ADD/DELETE
+/Ð/ENTER/MENU
3
Press ENTER to select the TV or CABLE
mode.
The arrow indicates the selected mode.
CH SETUP
TV CABLE
AUTO CH MEMORY
ADD/DELETE
TV
- VHF/UHF channels
CABLE - Cable TV channels
4
+/Ð/ENTER/MENU
Press VCR MENU until the menu screen is
cleared.
Note:
You can’t select “CH SETUP” if you set the channel to “L1” or
“L2”.
32
2I40301A-En_p28-33
32
21/3/06, 9:43 AM
0–9
ENTER
SET +/–
VCR MENU
To ADD/DELETE channels
Repeat the step 1 on page ! . Then press SET +
or – to select the “ADD/DELETE” and press
ENTER.
CH SETUP
When you don't want to receive a weak signal broadcast, a Blue
back screen can be obtained by selecting the NO NOISE BACKGROUND to “ON”. When the unit is shipped from the factory,
the NO NOISE BACKGROUND is set to “ON”.
1
TV CABLE
AUTO CH MEMORY
ADD/DELETE
Repeat the steps 1~2 on page ! and press
SET + or – to select “NO NOISE BACKGROUND”.
〈 〉
+/Ð/ENTER/MENU
2
To Add or Delete channels
1) Press Direct channel selection buttons (0–9)
or SET +/– to select a channel number you want
to add or delete.
2) To add channels
Press ENTER until “ADD” appears on the screen.
To delete channels
Press ENTER until “DELETE” appears on the
screen. The channel number will blink.
2
Press ENTER to select “ON” or “OFF” position.
3
Press VCR MENU until the menu screen is
cleared.
〈 〉
3) Repeat step 1 and 2 to add or delete other
channel.
Basic setup (VCR)
1
Noise elimination
3
Press VCR MENU until the menu screen is
cleared.
33
2I40301A-En_p28-33
33
21/3/06, 9:43 AM
Playback (VCR)
Loading and unloading a cassette tape
Use only video cassette tapes marked
.
EJECT
Loading
Push the center of the tape until it is automatically
inserted.
Insert the cassette tape with its labeled side facing up
and the erase prevention tab positioned at your left. An
inverted cassette tape cannot be inserted.
Erase prevention tab
Automatic power ON
When you insert a cassette tape, the DVD/VCR power will turn ON automatically.
Automatic playback
When loading a cassette tape without an erase prevention tab, playback will start automatically.
Unloading
1
Press EJECT on the front panel or on the remote.
2
Remove the cassette tape.
or
Automatic tape eject
This DVD/VCR will automatically rewind the tape when the tape has ended. Once the tape is rewound to its beginning,
the cassette tape will be ejected automatically.
To prevent accidental erasure
To prevent accidental erasure
Remove the erase prevention tab with a screwdriver.
To record again
Cover the hole with a piece of adhesive tape.
Screwdriver
Erase prevention tab
Adhesive tape
Tape speed and maximum recording time
Tape Speed
Video cassette tape
T-160
T-120
T-90
SP (Standard Play)
T-60
2-2/3 hours
2 hours
1-1/2 hours
1 hour
30 minutes
SLP (Super Long Play)
8 hours
6 hours
4-1/2 hours
3 hours
1-1/2 hours
34
2I40301A-En_p34-39
34
21/3/06, 9:43 AM
T-30
DVD/VCR
Cassette tape playback
To play a prerecorded tape.
STOP
PLAY
FWD
REV
DVD/VCR SELECT
Playback
Rewind or forward the tape
Preparation:
1
Stop the playback or recording via STOP on remote
control.
To rewind the tape:
Press REV.
Playback (VCR)
• Turn ON the TV and select the corresponding video input.
• Press DVD/VCR to operate the DVD/VCR.
• Press DVD/VCR SELECT to select the VCR mode.
(The VCR indicator will light).
Load a prerecorded tape
(When loading a cassette tape without the erase
prevention tab, playback will start automatically).
To forward the tape:
Press FWD.
2
To start playback
Press PLAY.
Playback will start. “ ” will appear
on the screen for about 4 seconds.
To discontinue the tape-winding, press STOP. To switch to
playback directly (without STOP), press PLAY.
To stop playback
Press STOP once.
The tape will stop but remain fully
loaded and ready to play.
“ ” will appear on the screen for
about 4 seconds.
Forward/Reverse picture search mode
When the tape is being winded, you can switch to picture
search mode (see page 36 ). To do this, press REV or
FWD and hold it down. The unit will resume the tape
advance or rewinding as soon as the button is released.
Notes:
• This VCR selects the playback tape speed SP, LP or SLP automatically.
• The Cassette tape and DVD disc can be played back simultaneously. If you press DVD/VCR SELECT, the tape playback
and DVD playback alternate with each other on the screen
(via CH3, 4 or video connection).
35
2I40301A-En_p34-39
35
21/3/06, 9:43 AM
Playback (VCR)
Special playback
CM SKIP
SET +/–
PLAY
PAUSE/STILL
FWD
SLOW
REV
ATR
Picture search
Adjusting tracking condition
Automatic tracking adjustment
Whenever you insert a tape and start playback, the
automatic tracking feature continuously analyzes the signal
to enable optimum picture quality during playback.
Reverse picture search function
Press REV once or twice during playback.
Forward picture search function
Press FWD once or twice during playback.
To return to playback, press PLAY.
SPEED SEARCH TIMES
TAPE SPEED
PICTURE SEARCH SPEED
PRESS ONCE
PRESS TWICE
SP (Standard Play)
3X
5X
LP (Long Play)
7X
9X
SLP (Super Long Play)
9X
15 X
Manual tracking adjustment
If automatic tracking cannot eliminate noises well during
playback, press SET +/– to eliminate the noise. “MANUAL
TR.” will appear on the screen. Press it once for a fine
adjustment, or press and hold for a coarse adjustment.
Press ATR to reactivate automatic tracking again.
“AUTO TR.” will appear on the screen.
Still picture
Press PAUSE/STILL during playback.
To resume normal playback, press PLAY or PAUSE/STILL.
Slow motion
During playback press SLOW.
To return to playback, press PLAY.
Slow tracking and vertical lock adjustment
If noise bars appear in the picture during slow motion,
press the SET + /– to reduce the noise bars.
If the still picture jitters excessively, press SET +/– to
stabilize the still picture.
Notes:
• The audio output is muted during PICTURE SEARCH, STILL,
FRAME ADVANCE and SLOW MOTION.
• During picture search mode there will be noise bars. This is
not a defect.
• Playback will commence after approx. 5 minutes to protect
the video tape against excessive wear during pause mode.
Video head cleaning
Video head clogging
The video heads are the means by
which the DVD/VCR reads the picture
from the tape during playback. In the
unlikely event that the heads become
Press PAUSE/STILL during playback.
Press SLOW repeatedly. The picture advances frame by dirty enough to be clogged, no picture
will be displayed. This can easily be
frame.
determined if, during playback of a
To return to playback, press PLAY or PAUSE/STILL.
known good tape, there is good sound,
but no picture (picture is extremely
snowy). If this is the case, the DVD/
VCR need to check and clean by the
qualified service personnel.
Frame by frame picture
Good Picture
CM skip
Press CM SKIP during playback. The DVD/VCR will search
Snowy Picture
forward through approximately 30 seconds of the tape (e.g. Notes:
unwanted commercial time) for each press of CM SKIP (maxi- • DO NOT ATTEMPT TO CLEAN THE VIDEO HEADS OR
mum six presses) and then resume normal playback.
SERVICE THE UNIT BY REMOVING THE REAR COVER.
For example
: 1 press: 30 seconds of tape
2 press: 60 seconds of tape
3 press: 90 seconds of tape
• Video heads may eventually wear out and should be replaced when they fail to produce clear pictures.
• To help prevent video head clogging, use only good quality VHS tapes. Discard worn out tapes.
36
2I40301A-En_p34-39
36
21/3/06, 9:43 AM
Convenience function
CALL
ZERO RETURN
SET +/–
ENTER
STOP
PLAY
CLOCK/COUNTER
VCR MENU
COUNTER RESET
Repeat playback
Zero return function
The entire video tape will play until its end. The tape will
automatically rewind to the beginning and the playback will be
repeated.
Press VCR MENU.
Press SET + or – to select “AUTO
REPEAT”.
1
Press CLOCK/COUNTER.
2
Press COUNTER RESET at the desired tape
position.
3
Press STOP when playback or recording is
completed.
Press ZERO RETURN.
The counter display shows the tape running time during playback or recording.
Playback (VCR)
1
This function rewinds the tape to the “00:00” counter position
automatically.
2
Press ENTER to select “ON” or “OFF”.
If “ON” is selected, the playback will
be repeated endlessly.
The counter display will be reset to
“00:00” position (e.g. the beginning of
recording).
3
4
Press VCR MENU until the menu screen is
cleared.
If you press CALL, “
on the screen 11 .
” will appear
The tape will automatically rewind or fast
forward to the “00:00” counter position.
To commence playback, press PLAY.
The playback will be repeated
endlessly.
To cancel repeat mode:
Follow the above step 1, then press ENTER to select “OFF”
position. Press VCR MENU to return to the TV.
37
2I40301A-En_p34-39
37
21/3/06, 9:43 AM
Playback (VCR)
Convenience function (Continued)
STOP
VISS +/–
CLOCK/COUNTER
DVD/VCR SELECT
Clock/counter display
Press CLOCK/COUNTER. The clock and tape counter
alternate with each other in the display window.
COUNTER
CLOCK
Press DVD/VCR SELECT. The DVD mode and the
VCR mode alternate with each other in the display.
DVD mode
Video index search system
This function enables you to locate the beginning of any recording
made on the VCR.
Recording an INDEX mark
The Index Search function automatically records an INDEX mark
on the tape whenever a recording
is initiated.
CH 001
INDEX
Index search
Press VISS + or – during stop or play mode.
For Succeeding programs: Press VISS +.
For Preceding programs: Press VISS –.
(As many as 9 index points can be accessed via this
method.)
When the VISS + or – is pressed,
the unit starts searching the selected INDEX NO. and finds the
portion. Then playback starts automatically. To stop the Index
Search, press STOP.
or
is displayed
INDEX NO. (up to 9)
VCR mode
Notes:
• If you rewind the tape beyond “00:00”, a minus sign (“–”) will
be displayed in front of the time.
• When you load a tape, the counter will reset to “00:00”.
• The counter does not function on non-recorded (blank)
sections of the tape. When you rewind, fast forward or play
tapes through blank sections, the counter stops.
Notes:
• When you record an INDEX mark at the very beginning of the
tape, the mark may not be found.
• During INDEX search, the tape may stop and begin to play at a
slightly different location.
• INDEX may not function properly with old or worn out video
tapes.
• INDEX marks may not be found if it is extremely close to the point
where the search began.
• During recording, if you stop recording temporarily, the INDEX
mark is not recorded on the tape.
SQPB (S-VHS Quasi Playback)
You can playback video cassette tapes recorded in the
S-VHS system.
However, the picture will not have the high resolution of
S-VHS system.
Note: You cannot record S-VHS video format with this VCR.
38
2I40301A-En_p34-39
38
21/3/06, 9:43 AM
Recording (VCR)
DVD/VCR
0–9
Recording a TV program
Recording and viewing the same TV program.
CH +/–
SP/SLP
DVD/VCR SELECT
REC/OTR
Recording a TV program
Preparation:
• Turn ON the TV and select to the corresponding
video input.
• Press DVD/VCR to operate the DVD/VCR.
• Press DVD/VCR SELECT to select the VCR mode.
(The VCR indicator will light.)
The DVD/VCR will automatically turn on.
+0 TV mode direct channel selection:
All channels can be instantly selected by using two
buttons. (for example, to select channel 2, press “0”, then
“2”. If you press only “2”, channel selection will be delayed
for two seconds.) For channels 10 and above, press the 2
digits in order.
CABLE mode direct channel selection:
Recording (VCR)
1
Load a cassette tape with the erase prevention
tab intact.
4
Press Number buttons or CH +/– to select the
channel to be recorded.
1-9
2
Press SP/SLP to select the desired tape speed
SP or SLP.
The tape counter and “SP” or “SLP”
will appear on the screen for about 4
seconds.
Press 0 twice and then 1-9 as required.
Example: To select “2”, Press 002.
10-12
Press 0 first and then the remaining 2 digits in
order from left to right.
Example: Press 012 for “12”.
13-99
Press 2 digits in order.
Example: Press 22 for “22”.
100-125 Press the 3 digits in order.
Example: Press 110 for “110”.
VHF/UHF/CABLE TV CHANNELS
TV
VHF
2-13
UHF
14-69
00 : 00 : 00 SP
3
CABLE TV
VHF
2-13
STD/HRC/IRC
14-36 (A) (W)
37-59 (AA) (WW)
60-85 (AAA) (ZZZ)
86-94 (86) (94)
95-99 (A-5) (A-1)
100-125 (100) (125)
01 (5A)
Select “TV” or “CABLE” to the appropriate
position ! .
TV
- VHF/UHF channels
CABLE - Cable TV channels
5
Press REC/OTR.
“ ” will appear on the screen for
about 4 seconds and “REC” will
appear on the display window.
CH 110
INDEX
39
2I40301A-En_p34-39
39
21/3/06, 9:43 AM
Recording (VCR)
Recording a TV program (Continued)
STOP
PAUSE/STILL
TV/VCR
To stop recording
Recording one program while watching another
Press STOP to stop recording.
While the VCR is recording, select your desired channel
on the TV.
When a TV is connected with an antenna cable only,
press TV/VCR to select the TV position.
The “VCR” display will go off and recording will continue.
Select the TV channel you want to watch by using the
TV channel selector.
“ ” will appear on screen for about
4 seconds.
Note:
Some Cable TV hookups do not permit viewing one channel
while recording another. See pages & and ' .
To stop recording temporarily
Press PAUSE/STILL to avoid recording unwanted
material. Press again to continue the recording.
“
” will appear on screen for
about 4 seconds.
Notes:
• The pause function will be released after 5 minutes to prevent
damage to the tape or the VCR. The VCR will change to the
STOP mode.
• You can select a recording channel in the recording pause
mode.
Auto Rewind feature
This VCR will automatically rewind the tape when the tape
has ended (except during OTR and timer recording). It will
also eject the tape.
40
2I40301A-En_p40-43
40
21/3/06, 9:43 AM
DVD/VCR
0–9
One-touch Timer Recording (OTR)
The One-touch Timer Recording feature provides a simple and
convenient way to make a timed recording.
CH +/–
STOP
SP/SLP
DVD/VCR SELECT
REC/OTR
One-touch Timer Recording (OTR)
Preparation:
• Turn ON the TV and select to the corresponding
video input.
• Press DVD/VCR to operate the DVD/VCR.
• Press DVD/VCR SELECT to select the VCR mode.
(The VCR indicator will light.)
Example: One-touch Timer Recording for 30 minutes.
Press Direct channel selection buttons (0–9) or
CH +/– to select the channel to be recorded.
+0 Load a cassette tape with the erase
prevention tab intact.
The VCR will automatically turn on.
5
Recording (VCR)
1
4
Press REC/OTR. Recording begins. Press the
button again to stop recording after 30 minutes.
Each additional press of REC/OTR will increase
recording time as shown in the chart below, up
to a maximum of 6 hours.
The OTR and recording time will
appear on the screen for about 4
seconds. And, “ ” will appear on
the display.
2
Press SP/SLP to select the desired tape speed
SP or SLP.
Press Recording time
NORMAL REC
once
0:30
twice
1:00
3 times
1:30
4 times
2:00
5 times
The tape counter and “SP” or “SLP”
will appear on the screen for about 4
seconds.
Press Recording time
3:00
6 times
4:00
7 times
5:00
8 times
6:00
9 times
10 times NORMAL REC
OTR 0 : 30
CH 110
00 : 00 : 00 SP
INDEX
3
Set “TV” or “CABLE” option to the appropriate
position ! .
To cancel OTR
Press STOP or turn off the power.
TV
- VHF/UHF channels
CABLE- Cable TV channels
“
” will appear on screen for about 4 seconds.
Note:
If you wish to watch the DVD playback during OTR or standard
recording, press DVD/VCR SELECT to change to DVD mode
and perform the DVD playback 47 .
41
2I40301A-En_p40-43
41
21/3/06, 9:44 AM
Recording (VCR)
DVD/VCR
Timer recording
Timer recording can be programmed on-screen with the remote control.
The built-in timer allows automatic unattended recording of up to 8
programs within 1 month.
SET +/–
ENTER
CANCEL
VCR MENU
EJECT
DVD/VCR SELECT
TIMER REC
Timer recording
Preparation:
• Press DVD/VCR to operate the DVD/VCR.
• Press DVD/VCR SELECT to select the VCR mode.
• Load a cassette tape with the erase prevention tab
intact.
• Check the time and date are correct ' .
Example: Program a timer recording for the 26th day,
channel 125 (Cable TV), 11:00 - 11:30 PM on timer
program number 1 (Tape speed: SLP).
1
5
To enter other programs, repeat steps 2
through 4.
• To return to the normal screen,
press VCR MENU twice.
Press VCR MENU. Select “TIMER REC SET”,
then press ENTER.
6
〈
〉
3
Set the start time, end time, channel and tape
speed as in step 3.
〈
〉
Notes:
• Press CANCEL to move cursor backward for correction.
• To record from external source set the channel to “L1” or
“L2”.
42
Notes:
• The timer recording will start at 5 seconds before the
preset starting time.
• If the timer symbol (
) does not appear on the display
when TIMER REC is pressed, the cassette is not inserted
.
• If the cassette is ejected when TIMER REC is pressed, the
erase prevention tab of the cassette may have been
removed 34 .
• During Timer recording, the power cannot be turned off.
Notes:
• If the timer symbol ( ) blinks when the timer recording ended,
the TV program has not been completely recorded because of
an insufficient tape length. Press TIMER REC to cancel the
timer program or press EJECT to remove the cassette tape.
• During timer recording standby mode, the VCR mode cannot be
operated. To use the VCR, first press TIMER REC then press
DVD/VCR SELECT to change to VCR mode. After VCR mode
is selected, press TIMER REC again to put the VCR into timer
recording standby mode.
• If you press TIMER REC during timer recording, the recording
operation will be interrupted. If you press TIMER REC again
within the programmed time, the recording operation will start
again.
• After a power failure or disconnection of the power plug, all
programmed recording settings and time display will be lost
upon resumption of power. In this case, reset the clock ' and
reprogram any timer recording.
42
2I40301A-En_p40-43
At the same time, VCR mode will
change to DVD mode automatically.
You can use DVD even if the VCR is
in the timer recording mode.
If you do not use the DVD, turn the
power off.
34
Press SET + or – to select the date, then press
ENTER.
〈
〉
4
Press TIMER REC. The timer symbol ( ) will
appear on the display and the VCR standbys
for recording.
Press SET + or – to select one of the program
line, then press ENTER.
〈
〉
2
21/3/06, 9:44 AM
SET +/–
ENTER
CANCEL
VCR MENU
DVD/VCR SELECT
TIMER REC
proceduretimer
ToSetting
set daily/weekly
To confirm or cancel a program
Weekly (e.g. WKL-TU: each Tuesday) or daily (e.g. MOSA: Monday to Saturday) Timer recording
Follow the procedure of timer recording on page 42 . At
step 3, press SET + or – repeatedly until the desired setting
appears. Then press ENTER.
1
If the Timer has been activated, press TIMER
REC to deactivate the Timer.
2
To confirm Timer program:
The timer symbol ( ) will
disappear. Then press DVD/VCR
SELECT to change to VCR mode.
When you press SET – repeatedly, the
DATE indicator will change as follows, in
this case the day is Friday.
Recording (VCR)
The current day (Friday)
SU-SA (Sunday to Saturday)
MO-SA (Monday to Saturday)
One month later
minus one day
MO-FR (Monday to Friday)
WKL-WE
(Weekly Wednesday)
WKL-TH (Weekly Thursday)
At step 1 on page 42 , select “TIMER REC SET”
and press ENTER.
The timer program list will appear on the screen.
〈
〉
9 : 00
10 : 00
CH
To cancel Timer program:
Press SET + or – to select the unwanted program,
then press CANCEL to cancel the program.
Do not overlap timer programs as portions of the
conflicting programs will be lost. The first recording
time has priority over the next recording time as shown
in the diagram below.
8 : 00
START END
11:00PM 11:30PM 125 SLP
〈+/—/ENTER/CANCEL/MENU〉
3
If the programs overlap another
DATE
26(SA)
11 : 00
Program 1
〈
〉
Program 2
Deleted Parts
Program 3
Non Recorded Portion Parts
Recording
Control Settings
Prog.1
Prog.2
Prog.3
4
Press VCR MENU repeatedly until the menu
screen is cleared.
Notes:
• The daily/weekly recording can be made continuously until the
recording is canceled or the tape reaches the end.
Notes:
• During timer recording the automatic rewinding mechanism
• If there are other timer record programs remaining, TIMER
does not function.
REC must be pressed to reactivate the timer, otherwise the
remaining timer record programs will be ignored.
• You cannot confirm the Timer program during timer recording
operation.
• You can correct or cancel a programmed setting in program
confirm mode.
43
2I40301A-En_p40-43
43
21/3/06, 9:44 AM
Other functions (VCR)
Stereo recording and playback/
Second Audio Program (SAP)
ENTER
SET +/–
VCR MENU
AUDIO SELECT
Stereo recording and playback
The VHS Hi-Fi audio system permits high fidelity recording of MTS STEREO TV broadcasts.
When a MTS STEREO broadcast is received, “STEREO” will
appear on the screen for about
4 seconds and the program can
be viewed or recorded in stereo.
The Hi-Fi stereo recording procedure is the same as for normal
recordings.
STEREO
Second Audio Program (SAP)
Your DVD/VCR is fitted with a SAP broadcast system which
enables you to switch to a second audio program when viewing a selected channel.
This function applies only when the program is broadcast in
multi-languages through the SAP broadcast system.
1
Press VCR MENU. Then press SET + or – to
select “SAP”.
Note:
When using a Cable TV system, stereo TV programs may
be transmitted over a mono cable channel. In this case
“STEREO” will not appear and the sound will be in mono.
Output selection
When viewing an MTS stereo TV program, or playing a
prerecorded VHS Hi-Fi stereo videotape, press AUDIO
SELECT to select how the audio will be heard through
the speakers. Normally set to the Hi-Fi stereo position,
this button can be set to the MONO position if the
stereo broadcast or videotape audio is of poor quality.
The “R” and “L” positions allow the audio from the Right
or Left Hi-Fi channel to be heard over both TV speakers. This button has no effect when viewing a MONO
videotape or TV program. Each time when you press
the button, OUTPUT SELECTION display appears on
the screen for several seconds. Refer to the chart
below.
OUTPUT
SELECTION
SOUND HEARD ON BOTH
SPEAKERS
STEREO
L ch
R ch
MONO
STEREO
LEFT CHANNEL AUDIO
RIGHT CHANNEL AUDIO
MONO
2
Press ENTER to select “ON”.
Then press VCR MENU until the
menu screen is cleared.
Listening to SAP
When the VCR is turned on or a channel selection is
made, make certain the letters “SAP” appears on the
screen for about 4 seconds. This means that the “Second
Audio Program” broadcasting is available.
5)2
OR
Notes:
• When playing back a tape that is not recorded in Hi-Fi stereo
mode, the audio will automatically be monaural.
• When listening to a VHS Hi-Fi video tape or MTS broadcast
through the VHF/UHF jack (Audio/Video cable not connected),
the sound will be monaural.
44
2I40301A-En_p44-47
44
21/3/06, 9:44 AM
DVD/VCR
Duplicating a video tape
If you connect the DVD/VCR to another VCR or Camcorder, you can duplicate
a previously recorded tape. Make all connections before turning on the power.
INPUT SELECT
STOP
SP/SLP
DVD/VCR SELECT
REC/OTR
Duplicating a video tape
Preparation:
• Turn ON the TV and select the corresponding video
input.
• Press DVD/VCR to operate the DVD/VCR.
• Press DVD/VCR SELECT to select the VCR mode.
(The VCR indicator will light.)
• Load a cassette tape with the erase prevention tab
intact.
• Load a previously recorded tape into the playback
VCR or Camcorder.
Connection with second VCR
Playback VCR
To VIDEO OUT
To AUDIO (R) OUT
To AUDIO (L) OUT
1
AUDIO/VIDEO cable (supplied)
It is recommended to set the tape
speed to the SP mode on the
recording VCR for best results.
Press INPUT SELECT once or twice to select
AUDIO/VIDEO input position.
Recording VCR
To VIDEO IN
“L1” or “L2” will appear in the display.
Other functions (VCR)
2
Press SP/SLP to select the desired tape speed
SP or SLP.
To AUDIO (R) IN
To AUDIO (L) IN
Connection with Camcorder
L1: on the rear panel
L2: on the front panel
3
Playback Camcorder
Press PLAY on the playback VCR or Camcorder.
To AV Jack
Recording VCR
4
Press REC/OTR on the recording VCR.
The duplicating process begins.
To AUDIO (R) IN
To AUDIO (L) IN
To VIDEO IN
5
Press STOP when you finish duplicating.
AUDIO/VIDEO cable (not supplied)
For duplicating a previously recorded tape from a
camcorder, follow the camcorder manufacturer’s
instructions. A typical camcorder dubbing hookup is
shown above.
45
2I40301A-En_p44-47
45
21/3/06, 9:44 AM
Other functions (VCR)
DVD/VCR
Recording a DVD/CD disc
You can record disc material in DVD, Video CD, Audio CD, etc.
onto a Video tape with this DVD/VCR.
STOP
PLAY
SP/SLP
DVD/VCR SELECT
REC/OTR
Duplicating a DVD or CD disc
Preparation:
• Turn ON the TV and select the corresponding video
input.
• Press DVD/VCR to operate the DVD/VCR.
• Press DVD/VCR SELECT to select the VCR mode.
(The VCR indicator will light.)
• Load a cassette tape with the erase prevention tab intact.
• Load a DVD/CD disc.
1
Press SP/SLP to select the desired tape speed
SP or SLP.
00 : 00 : 00 SP
2
Press DVD/VCR SELECT selector to select the
DVD mode.
3
Press PLAY to start playback.
4
Press REC/OTR to start recording.
5
Press STOP when you finish recording.
Notes:
• You may not be able to record the beginning of the disc.
Begin VCR recording once program playback commences
on the DVD.
• When the scanning mode is set to the progressive mode,
you cannot duplicate a disc material onto a video tape.
When REC/OTR is pressed, the PROGRESSIVE indicator
“ ” on the display window will flash.
• When the HDMI mode is ON (480p, 720p, 1080i), you
cannot duplicate a disc material onto a video tape.
• You cannot record discs encoded with copy guard
function. The following icon and text will show up on the
TV screen.
DISC IS COPY PROTECTED
The DVD indicator will light.
The DVD/VCR will change to the
VCR mode automatically and the
playback picture or sound will be
duplicated on the video cassette
tape.
If you wish to stop a DVD/CD disc,
press DVD/VCR SELECT selector to
change the DVD mode, then press
STOP.
46
2I40301A-En_p44-47
46
21/3/06, 9:44 AM
Basic playback (DVD)
DVD/VCR
Playing a disc
This section shows you the basics on how to play a disc.
ON/STANDBY
CAUTION
Keep your fingers well clear of the
disc tray as it is closing. Neglecting
to do so may cause serious
personal injury.
DVD
VCD
CD
VCR/DVD
STOP
Disc tray
C/D/B/A
ENTER
Display window
PLAY
OPEN/CLOSE
Basic playback
Preparations:
• When you want to view a disc, turn on the TV and select the corresponding video input connected to the DVD/VCR.
This may include S-video or component video inputs which are exclusive to DVD playback.
• When you want to enjoy the sound of discs from the audio system, turn on the audio system and select the input
connected to the DVD/VCR.
1
Press DVD/VCR on the remote control to
operate the DVD/VCR.
6
Press OPEN/CLOSE or PLAY on the unit.
The disc tray closes automatically.
On the TV-screen, “ ” changes to
“Reading” and then playback
commences.
OR
2
Press
ON/STANDBY.
• A menu screen will appear on the TV screen, if
the disc has a menu feature.
The DVD/VCR turns on.
Reading
Press VCR/DVD on the unit to select the DVD mode.
4
Press OPEN/CLOSE.
5
The DVD indicator will light.
7
Press
8
Press ENTER.
9
Press STOP to end playback.
/
or
/
Basic playback (DVD)
3
to select title.
The disc tray opens.
Place the disc on the disc tray.
With the playback
side down
• There are two different disc sizes. Place the disc
in the correct guide on the disc tray. If the disc is
out of the guide, it may damage the disc and
cause the DVD/VCR to malfunction.
• Do not place a disc which is unplayable in this
DVD/VCR.
• Title is selected and play
commences.
• The unit records the stopped point,
depending on the disc. “ ”
appears on the screen. Press
PLAY to resume playback (from
the scene point).
• If you press STOP again or unload
the disc (“ ” appears on the
screen.), the unit will clear the
stopped point.
To start playback in the stop mode
Press PLAY.
47
2I40301A-En_p44-47
47
21/3/06, 9:44 AM
Basic playback (DVD)
To obtain a higher quality picture
Occasionally, some picture noise not usually visible on the TV screen during a normal
broadcast may appear while playing a DVD video disc.
It is because due to high resolution pictures on these discs which include a lot of
information. The amount of noise depends on the disc you use with this unit. You should
generally reduce the sharpness adjustment on your TV when viewing DVD video discs.
About DVD VCD CD 75*
The DVD VCD CD icons on the heading bar show the playable discs for the
STOP
function described under that heading.
PLAY
DVD : You can use this function with DVD video discs.
PAUSE/STILL
VCD : You can use this function with Video CDs.
CD
DVD/VCR SELECT 75* : You can use this function with Audio CDs and CD-R/RW CDs.
: You can use this function with USB Mass Storage.
OPEN/CLOSE
POWER
DVD
VCD
CD
Basic playback
To pause playback (still mode)
Press PAUSE/STILL during playback.
To resume normal playback, press
PLAY.
• The sound is muted during still
mode.
To stop playback
Press STOP.
To remove the disc
Press OPEN/CLOSE.
Remove the disc after the disc tray
opens completely.
Playing a Disc while the VCR section is recording
or standing by for timer recording
1) Start to record.
Follow steps 1~5 on page !' .
• If the DVD/VCR is standing by for recording, turn on
the DVD/VCR.
2) Press DVD/VCR SELECT selector to select DVD mode.
3) Play a disc.
Follow steps 4 ~ 6 on page 47 .
• Press PLAY if the DVD/VCR does not start to play a
disc automatically.
4) Stop to play.
Press STOP to stop play back a disc.
Screen saver function
The screen saver operates when you leave the unit in
DVD stop mode for approx. five minutes.
The screen will repeatedly get dark gradually and back
to normal.
Please press any button when you want to return to an
usual screen.
To turn on or off the screen saver, see page $$ .
Be sure to press OPEN/CLOSE to close the disc tray
after you remove the disc.
Notes:
• If a non-compatible disc is loaded, “Incorrect Disc”, “Region Code Error” or “Parental Error” will appear on the TV screen
according to the type of loaded disc. In this case, check your disc again % % .
• Some discs may take a minute or so to start playback.
• When you set a single-faced disc label downwards (i.e. the wrong way up) and press OPEN/CLOSE or PLAY on the unit,
“Reading” will appear on the display for a few minutes and then “Incorrect Disc” will continue to be displayed.
• Some discs may not work the resuming facility.
• Resuming cannot function when you play a PBC-featured Video CD while the PBC is on. To turn off the PBC, see page 56 .
• Some playback operations of DVDs may be intentionally fixed by software producers. Since this unit plays DVDs according to
the disc contents the software producers designed, some playback features may not be available. Also refer to the
instructions supplied with the DVDs.
• Do not move the unit during playback. Doing so may damage the disc.
• Use the OPEN/CLOSE to open and close the disc tray. Do not push the disc tray while it is moving. Doing so may cause the
unit to malfunction.
• Do not push up on the disc tray or put any objects other than discs on the disc tray. Doing so may cause the unit to
malfunction.
• In many instances, a menu screen will appear after playback of a movie is completed. Prolonged display of an on-screen
menu may damage your television set, permanently etching that image onto its screen. To avoid this, be sure to press
POWER on your remote control once the movie is completed.
• There may be a slight delay between the button is pressed and the function activates.
• The screen saver does not operate when connecting this DVD/VCR to the TV using the HDMI cable.
48
2I40301A-En_p48-51
48
21/3/06, 9:44 AM
Playing a disc (Continued)
You can play discs at various speeds.
PAUSE/STILL
PLAY
FWD
SLOW
REV
SKIP /
DVD
VCD
CD
Playing in fast reverse or fast forward directions
Press REV or FWD during playback.
FWD
REV: Fast reverse playback
FWD: Fast forward playback
Each time you press REV or FWD,
the playback speed changes.
DVD
VCD
To resume normal playback
Press PLAY.
Notes:
• The DVD/VCR mutes sound and subtitles during reverse
and forward scan of DVD/VCD video discs. However, this
unit plays sound during fast forward or fast reverse play of
audio CDs.
• The playback speed may differ depending on the disc.
Playing frame by frame
Press PAUSE/STILL during still playback.
To resume normal playback
Press PLAY.
Each time you press PAUSE/STILL,
the picture advances one frame.
Basic playback (DVD)
Note:
The sound is muted during frame by frame playback.
DVD
VCD
Playing in slow-motion
Press SLOW during playback.
Each time you press the button, the
slow-motion speed changes.
DVD
VCD
CD
To resume normal playback
Press PLAY.
Note:
The sound is muted during slow-motion playback.
Locating a chapter or track
Press SKIP
or
repeatedly to display the chapter or track number you want.
Playback starts from the selected chapter or track.
To locate succeeding chapters or
tracks.
Playback starts from the beginning of the
current chapter or track.
When you press twice in quick successions,
playback starts from the beginning of the
preceding chapter or track.
Notes:
• A prohibition symbol “ ” may appear at the upper right of the screen. This symbol means either the feature you tried is not
available on the disc, or the DVD/VCR cannot access the feature at this time. This does not indicate a problem with the DVD/
VCR.
• The unit is capable of holding a still video image or On screen display image on your television screen indefinitely. If you leave
the still video image or On screen display image displayed on your TV for an extended period of time, you risk permanent
damage to your television screen. Projection televisions are very susceptible.
49
2I40301A-En_p48-51
49
21/3/06, 9:44 AM
Advanced playback (DVD)
Zooming/Locating desired scene
0–9
DISPLAY
JUMP
C/D/B/A
ENTER
CLEAR
ZOOM
DVD
VCD
CD
Zooming
This unit will allow you to zoom in on the frame image. You can then make selections by switching the position of the frame.
1
Press ZOOM during playback.
The center part of the image will be
zoomed in.
Each press of ZOOM will change the
ZOOM 1 (x 1.3), 2 (x 1.5) and 3
(x 2.0).
1
2
D/B
B/A
A to view a different part of the
Press C/D
frame.
You may move the frame from the
center position to UP, DOWN, LEFT or
RIGHT direction.
3
In the zoom mode, press ZOOM repeatedly to
return to a 1:1 view ( Off).
Notes:
• You can select the Pause, Slow or Search playback in the zoom mode.
• Some discs may not respond to zoom feature.
DVD
VCD
CD
Locating desired scene
Use the title, chapter and time recorded on the DVD disc to locate the desired point to play back. In the case of VCD/CD
discs, time and track are used to locate the desired point to play back. To check the title, chapter and time, press DISPLAY.
1
Press JUMP during playback or resume stop
mode.
Jump
3
Press Number buttons (0–9) to change the
number.
Jump
Title
Chapter
Time
2
Title
Chapter
Time
Press C or D to select the “Title/Track”, “Chapter”
or “Time”.
• If you input a wrong number, press
CLEAR.
• Refer to the package supplied with
the disc to check the numbers.
Jump
Title
Chapter
Time
Notes:
• In case of the Audio CD and Video-CD, only Track and Time
can be selected.
• In case of the Video-CD playback with PBC, the JUMP does
not work. Turn off the PBC 56 .
4
Press ENTER. Playback starts.
• When you change the title,
playback starts from Chapter 1 of
the selected title.
• Some discs may not work in the
above operation.
50
2I40301A-En_p48-51
50
12
21/3/06, 9:44 AM
Marking desired scenes
The unit stores the points that you want to watch again up to 3 points.
You can resume playback from each scene.
C/D
ENTER
CLEAR
MARKER
DVD
VCD
1
Marking the scenes
DVD
VCD
Press MARKER during playback.
1
Returning to the scenes
Press MARKER during playback or stop mode.
Marker1
Marker2
Marker3
2
Marker1
Marker2
Marker3
Select the blank Marker using C or D.
Then press ENTER at the desired scene.
2
Press C or D to select the Marker 1-3.
Marker1
Marker2
Marker3
• Repeat this procedure to set the
other 2 scenes.
Marker1
Marker2
Marker3
3
00 27 54
01 16 25
02 08 31
Press ENTER.
Playback starts from the marked
scene.
Press MARKER to clear this display.
To cancel the Marker
Follow the above steps 1~2, then press CLEAR.
Notes:
• Some discs may not work with the marking operation.
• The marking is canceled when you open the disc tray or
turn the power off.
• Some subtitles recorded around the marker may fail to
appear.
• In case of Video CD with PBC, Marker function is prohibited.
Advanced playback (DVD)
3
00 27 54
00 27 54
01 16 25
02 08 31
51
2I40301A-En_p48-51
51
21/3/06, 9:44 AM
Advanced playback (DVD)
Repeat playback/A-B Repeat playback
ENTER
D
PLAY
PLAYMODE
A-B RPT
DVD
VCD
1
2
DVD
VCD
CD
Repeat playback
Press PLAYMODE during playback or stop mode.
A-B Repeat playback
A-B repeat playback allows you to repeat material between
two selected points.
1
Press A-B RPT during playback.
The start point is selected.
[DVD]
Press ENTER to select “Chapter” or “Title”.
A
Play Mode
Repeat
: Off
The unit automatically starts repeat
playback after finishing the current title or chapter.
[Video CD]
Press D to select “Repeat”.
Press ENTER to select “Track” or “All”.
2
Press A-B RPT again.
The end point is selected. Playback
starts at the point that you selected.
Playback stops at the end point, returns to Point A automatically, then
starts again.
Play Mode
Mode
: Off
Repeat
: Off
1
2
3
ÐÐÐ
ÐÐÐ
ÐÐÐ
A B
The unit automatically starts repeat
playback after finishing the current
track.
• If you set the repeat mode during stop mode,
press PLAY to start Repeat playback.
To resume normal playback
Press A-B RPT again.
“
Off ” appears on the screen.
[Audio CD and MP3/WMA CD]
Please see “Repeat playback (CD/USB)” $ .
3
Press PLAYMODE again to clear the screen.
To resume normal playback
Select Repeat : “Off” in step 2.
Notes:
• Some discs may not work with the repeat operation.
• In case of Video CD with PBC, repeat functions are prohibited during playback.
• Chapter/Track repeat function is canceled whenever
SKIP
or
is pressed.
Notes:
• In A-B Repeat mode, subtitles near the A or B locations may
not be displayed.
• You cannot set the A-B Repeat for the scenes that include
multiple angles.
• A-B Repeat playback does not work when Repeat playback is
activated.
• You may not be able to set A-B Repeat, during certain scenes
of the DVD.
• A-B Repeat does not work with an interactive DVD, MP3/WMA/
JPEG/DivX® CD.
• A-B Repeat is prohibited when PBC is on.
52
2I40301A-En_p52-59
52
21/3/06, 9:44 AM
Program playback/Random playback
0–9
You can arrange the playback order of tracks or files on the disc.
And the unit can also select tracks or files at random and playback
them. These feature works for Video CD.
C/D/B/A
ENTER
CLEAR
PLAY
For Audio CD and MP3/WMA CD, please see “Random playback
(CD/USB)” $ and “Program playback (CD/USB)” 62 .
PLAYMODE
VCD
1
Program playback
4
Press PLAYMODE during stop mode.
Play Mode
Mode
: Off
Repeat
: Off
Program Playback
1
2
———
———
3
———
A to return to the left column, then
Press B/A
D to select the “Program Playback”
press C/D
and press ENTER.
The programs you selected will start to playback in
the order.
• To resume normal playback, select Mode
2
“Off” in step 2.
D to select “Mode”, then press
Press C/D
ENTER to select “Program”.
Play Mode
Play Mode
Mode
: Program
Repeat
: Off
Program Playback
3
1
2
3
–––
–––
–––
A to select the right column, then use
Press B/A
Number buttons (0–9) to input the track numbers.
Play Mode
Mode
: Program
Repeat
: Off
Program Playback
VCD
1
2
1
2
3
9
–––
–––
: Program
Repeat
: Off
Program Playback
1
2
3
9
3
11
■ To change the program
1. Select Mode to “Program” (as step 2), press B /A/C/
D to select the track number you want to change, then
press CLEAR.
2. Press Number buttons (0–9) to overwrite the new
track number.
■ To clear the program one by one
Select Mode to “Program”, press B/A/C/D to select the
track number. Then press CLEAR.
■ To clear all the programs
In the left column, press C/D to select “Clear Program”.
Then press ENTER.
Notes:
• In playing back the Video CD with PBC, you cannot set
Program playback.
• The program is canceled when you open the disc tray or
turn the power off.
Advanced playback (DVD)
• If you input a wrong number, press
CLEAR.
Mode
Random playback
Press PLAYMODE during playback or stop mode.
D to select “Mode”, then press
Press C/D
ENTER to select “Random”.
Play Mode
Mode
: Random
Repeat
: Off
Program Playback
1
2
–––
–––
3
–––
3
Press PLAY.
The Random Playback will start.
• If you set “Random” during playback mode,
Random playback will begin after the track that is
currently being played has ended.
• To resume normal playback, select Mode
“Off” in step 2.
Note:
In playing back the Video CD with PBC, you cannot set
Random playback.
53
2I40301A-En_p52-59
53
21/3/06, 9:45 AM
Advanced playback (DVD)
Changing angles/Title selection/DVD menu
DVD MENU
C/D/B/A
ENTER
PLAY
TOP MENU
ANGLE
DVD
Changing angles
When playing back a disc recorded with multi-angle facility, you can change the angle that you are viewing the scene from.
1
Press ANGLE during playback.
The current angle will appear.
2
Press ANGLE repeatedly until the desired angle
is selected.
1/2
Note:
Depending on the DVD, you may not be able to change the
angles even if multi-angles are recorded on the DVD.
DVD
Title selection
Two or more titles are recorded on some discs. If the title menu is recorded on the disc, you can select the desired title.
1
Press TOP MENU during playback.
2
D/B
B/A
A to select the desired title.
Press C/D
Title menu appears on the screen.
3
Press ENTER or PLAY.
The playback of the selected title will
start.
Note:
Depending on the DVD, you may not be able to select the title.
Depending on the DVD, a “title menu” may simply be called a
“menu” or “title” in the instructions supplied with the disc.
DVD
DVD menu
Some DVDs allow you to select the disc contents using the menu.
When you play back these DVDs, you can select the subtitle language and sound-track language, etc. using the menu.
1
Press DVD MENU during playback.
The DVD menu appears on the screen.
• Press DVD MENU again to resume
playback at the scene when you
press DVD MENU.
2
D/B
B/A
A to select the desired item.
Press C/D
3
Press ENTER.
The menu continues to another
screen. Repeat steps 2 and 3 to set
the item completely.
Note:
Depending on the DVD, you may not be able to resume playback
from the scene point when you press DVD MENU.
54
2I40301A-En_p52-59
54
21/3/06, 9:45 AM
Changing soundtrack language/
Setting surround sound
B/A
AUDIO
DVD
VCD
Changing soundtrack language
You can select the language when you play a multilingual disc.
1
Press AUDIO during playback.
The current soundtrack language will
appear.
In case of Video CD playback
Audio type changes as follows each time you press AUDIO.
LR
L
R
1/2 Eng Dolby Digital
2
Press AUDIO repeatedly until the desired language is selected.
2/2 Fre Dolby Digital
Notes:
• If the desired language is not heard after pressing the
button several times, the language is not recorded on
the disc.
• Changing soundtrack language is canceled when you
open the disc tray. The initial default language or available
language will be heard if the disc is played back again.
• The on screen display will disappear after a few
seconds.
Setting surround sound
This DVD video player equipped with a “QSound”. It can produce the effect of being in a cinema or a concert hall.
1
During disc playback press AUDIO.
QSound Off
2
Press B or A to select “On”.
To cancel Surround mode:
Follow the left steps 1~2, then press B or A to select the
“Off” position.
Notes:
• The QSound setting can also be changed in the function
setting $% .
• The “QSound” works only when the DVD disc recorded
with Dolby Digital is played back.
• When this function works, the volume might changed.
• When the voice is distorted, turn off QSound.
Advanced playback (DVD)
DVD
QSound On
• The on screen display will disappear after a few
seconds.
Manufactured under license from QSound Labs,
Inc. U.S. patent Nos. 5,105,462, 5,208,860 and
5,440,638 and various foreign counterpart.
Copyright QSound Labs, Inc. 1998-2002.
QXpander™ is a trademark of QSound Labs, Inc.
All rights reserved.
55
2I40301A-En_p52-59
55
21/3/06, 9:45 AM
Advanced playback (DVD)
Subtitles/To turn off the PBC
C/D
ENTER
SUBTITLE
PLAYMODE
DVD
To turn off the PBC (see page 8)
Subtitles
When playing back a disc recorded with subtitles, you can
select the subtitle language or turn the subtitle off.
1
1
Press PLAYMODE in the stop mode.
2
Press / to select “Mode”, then press
ENTER repeatedly until “Off” appear.
Press SUBTITLE repeatedly during playback
until your desired language appears.
1/5 Eng
Play Mode
2
Mode
To turn off the subtitle, press SUBTITLE until
“Off” appears.
: Off
Repeat
: Off
Program Playback
1
2
3
———
———
———
Off
• The on screen display will disappear after a few
seconds.
Notes:
• Depending on the DVD, you may not be able to change
subtitles, or to turn subtitles on or off.
• While playing a DVD, the subtitle may change when you
open or close the disc tray.
• In some cases, a selected subtitle language may not be
changed immediately.
3
Press PLAYMODE again to clear the screen.
To turn on the PBC
Follow the above steps 1~2, then press ENTER repeatedly
until “PBC” appear.
56
2I40301A-En_p52-59
56
21/3/06, 9:45 AM
MP3/WMA/JPEG/DivX® and Audio CD operation
This player can playback the MP3/WMA/JPEG/DivX®-data which has been recorded on CD-R/RW or USB Mass Storage. To
produce the MP3/WMA JPEG/DivX®-data, you need a Windows-PC with CD-RW drive or USB memory device and a MP3/
WMA/JPEG/DivX®-encoding Software (not supplied). The Apple-HFS-System cannot be played.
This player requires discs/recordings to meet certain technical standards in order to achieve optimal playback quality.
There are many different types of recordable disc formats (including CD-R containing MP3/WMA files). Not all
recordable discs will produce optimal playback quality. The technical criteria set forth in this owner's manual are meant
only as a guide. Use of CD-RW for MP3 files is not recommended.
You must obtain any required permission from copyright owners to download or use copyrighted content.
Toshiba cannot and does not grant such permission.
MP3/WMA/JPEG/DivX® - data information
Limitations on MP3/WMA/JPEG/DivX® playback
• MP3/WMA/JPEG/DivX® CD/USB Mass Storage are standardized by ISO9660, its file name must include following
extensions; “.mp3”, “.wma”, “.jpg”, “.div”, “.divx”, “.avi”.
• MP3/WMA/JPEG/DivX® CD/USB Mass Storage must be correspond to the ISO standardized files.
• This unit can read 600 files per disc. If one directory has more than 600 files, it reads up to 600 files, the remaining files
will be omitted. (In case of USB Mass Storage, this limitation becomes 2,000 files).
• The unit is able to recognize up to a maximum of 50 directories per disc or USB Mass Storage.
• MP3/WMA/JPEG/DivX® CDs/USB Mass Storage cannot be used for the purpose of recording.
• If the CD/USB Mass Storage has both audio tracks and MP3/WMA/JPEG/DivX® files, only audio tracks are played.
• It may take more than one minute for this unit to read MP3/WMA/JPEG/DivX® files depending on its structure.
• Music recorded by “Joliet Recording Specification” can be played back, the file name is displayed (within 15 letters) on
the screen. Long file names will be condensed.
• The music files recorded by “Hierarchical File System” (HFS) cannot be played.
Limitations on display.
• The maximum number for display is 15 letters.
Available characters for display are the following:
capital or small alphabets of A through Z, numbers of 0 through 9, and _ (under score).
• Other characters than those above are replaced in hyphen.
Advanced playback (DVD)
Notes on MP3/WMA/JPEG/DivX® files
To playback MP3/WMA/JPEG/DivX® CD/USB Mass Storage in the recorded order,
1. Use MP3/WMA/JPEG/DivX® software that records data alphabetically or numerically.
2. Insert two or three digit number in the head of file name. (ex. “01” “02” or “001” “002”).
3. Refrain from making too many sub-folders.
CAUTION:
• Some MP3/WMA/JPEG/DivX® CDs/USB Mass Storage cannot be played back depending on the recording conditions.
• The CD-R/RW or USB Mass Storage that has no music data or non MP3/WMA/JPEG/DivX® files cannot be played back.
Standard sampling frequency, and the bit rate:
MP3
MPEG-1 Audio
32kHz, 44.1kHz, 48kHz
32kbps ~ 320kbps (constant bit rate or variable bit rate)
The recommend recording setting for a high-quality sound is 44.1kHz of sampling frequency and 128kbps of constant bit
rate.
WMA
WMA version 7 and 8
32kHz/48kbps, 44.1kHz/48kbps~192kbps, 48kHz/128kbps~192kbps
The file recorded by mono, 48kHz, 48 kbps is not available to this unit.
DivX® video
DivX® version: DivX® 3, 4, 5, and 6 (specifically 3.1.1, 4.1.2, 5.0.2, 5.0.5, 5.1.1, 5.2.1, 6.0 at Home Theater profile).
Audio format: MPEG1 Layer2 (MP2), MPEG1 Layer3 (MP3)
Sampling frequencies: 32kHz, 44.1kHz, 48kHz
Bit rate: 32kbps ~ 320kbps
Resolution: Max 720 x 576 (at 25fps), Max 720 x 480 (at 30fps)
Microsoft, Windows Media, and Windows Logo are either registered trademarks or trademarks of Microsoft Corporation in the
United States and/or other countries.
DivX, DivX Certified, and associated logos are trade marks of DivX, Inc. and are used under license.
57
2I40301A-En_p52-59
57
21/3/06, 9:45 AM
Advanced playback (DVD)
MP3/WMA/JPEG/DivX® and Audio
CD operation (Continued)
▲/▼/ /
ENTER
RETURN
STOP
PLAY
DVD/USB
OPEN/CLOSE
+,
75*
1
+,
75*
Loading media
[MP3/WMA/JPEG/DivX® CD, Audio CD]
Place a MP3/WMA/JPEG/DivX® CD or an Audio
CD onto the disc tray, then press OPEN/CLOSE.
1
MP3/WMA and Audio CD playback
In the file browser, press
desired file.
Press DVD/USB to display the media selection
window. Press B or A to select the DISC
mode or the USB mode, then press ENTER.
DISC
USB
You cannot select the mode if
DISC/USB media is not inserted.
3
A file browser screen will be appear on the
screen.
!' '() # ( # " '(
# -
$ && && &&
$%
!""
# !""
* +
'#
,
'#
,1$ # ,1
34 5
.'# " /#$$0
.'# " /0
.'# " /12 #0
• In case the current directory includes 9 files or more,
press
or
to scroll in the file list.
• To see contents in folder, select the folder and then
press ENTER. To return to the upstairs directory, select
“ Go Up ...” then press ENTER.
• In case of a CD/USB Mass Storage containing a mixture
of MP3, WMA, JPEG and DivX® files, the files are played
back by selecting them from the file browser.
58
!""
!""
When PLAY is pressed after the file browser displayed,
playback begins automatically starting from the first file. In
this case, if the first file is an MP3/WMA file, only MP3/
WMA files are played back in order. If the first file is a
JPEG file, the first JPEG file is played back. If the first file is
a DivX® file, the first DivX® file is played back. If there is no
file at a root directory, playback does not begin
automatically.
2
Press ENTER.
3
Press STOP to end playback.
The selected file starts playing
back.
• The unit records the stopped point. “ ” appears on the
screen. Press PLAY to resume playback (from the scene
point).
• If you press STOP again or unload the disc, the unit will
clear the stopped point.
Notes:
• MP3 or WMA file on the Kodak Picture CD is not recognized
on this unit.
• During MP3/WMA/JPEG-Playback, you cannot use Jump and
A-B Repeat functions.
• You can use Repeat (Track or All), Random functions and
Program playback for MP3/WMA/JPEG/DivX®-Playback $ ,
62 .
• At USB mode with no disc on the tray, you can move to DISC
mode when you press OPEN/CLOSE on the remote control.
Select Files
The file type to make it display in the file browser can be chosen.
1. Press B or A to highlight “Select Files” at right column
in the file browser.
or
to select file type
2. Press ENTER, then press
from the list (Music, Picture or Movie).
3. Press ENTER to add/remove check mark. Checked file
type will be displayed in the file browser.
4. Press RETURN to save the setting.
58
2I40301A-En_p52-59
to select the
[USB Mass Storage]
Connect USB Mass Storage to the USB port on
the front of the unit (see page $ ).
2
/
21/3/06, 9:45 AM
ck
TOP MENU
ZOOM
DVD MENU
C/D/B/A
ENTER
STOP
PLAY
SKIP
PAUSE/STILL
ANGLE
+,
75*
1
+,
75*
JPEG playback
In the file browser, press C/D to select the
desired JPEG file.
To display a thumbnail list, press DVD MENU.
Press B/A or C/D to select the desired file.
(To return to a file browser, press TOP MENU.)
/Picture-01.JPG
Picture-01
Picture-02
Picture-03
Picture-04
Picture-05
Picture-06
Picture-07
Picture-08
Select Files
Repeat
:Off
Mode
:Off
JPEG Preview
W: 2048 H: 1536
When PLAY is pressed after displaying the file
browser, playback begins automatically starting
from the first file. In this case, if the first file is a
JPEG file, the first JPEG file is played back. If the
first file is a DivX® file, the first DivX® file is
played back. If the first file is an MP3/WMA file,
only MP3/WMA files are played back in order. If
there is no file at a root directory, playback does
not begin automatically.
Press ENTER. The selected picture appears on
the screen.
The slide show enables you to view pictures (files) one after
another automatically.
Preparation:
Set “JPEG Interval” setting to “5 Seconds”, “10 Seconds”
or “15 Seconds” $$ .
1
2
Select your desired starting file for the slide
show in step 1 on the left.
Press ENTER or PLAY to start slide show from
the selected file.
• If you press PAUSE/STILL during the slide show, the
slide show stops temporary. “ 4 ” appears briefly on
the screen.
If the picture appears upside down or sideways, press
ANGLE repeatedly until it’s right side up.
Press PLAY or SKIP
again to resume the slide show.
• When the slide show playback finished, the file list appears.
• To stop the slide show, press STOP. The file list appears.
Notes:
Rotating an image
You can rotate an image by 90 degrees by
pressing ANGLE during playback of the image.
”, “
“
screen.
”, “
” or “
• If the DVD/VCR is connected to a HDTV using HDMI, you
can display the HD resolution JPEG images (720p or
1080i). See “HD Jpeg” on page $& .
• During JPEG playback, you cannot use Jump and A-B
Repeat functions.
Advanced playback (DVD)
2
Slide show playback
” appears on the
Zooming an image
Zoom function also can be used in viewing JPEG
files. Press ZOOM (See “Zooming” # ).
3
Press STOP to end playback.
The file browser appears on the
screen. If you want to watch the
other file, repeat steps 1 ~ 2.
59
2I40301A-En_p52-59
59
21/3/06, 9:45 AM
Advanced playback (DVD)
MP3/WMA/JPEG/DivX® and Audio
CD operation (Continued)
+,
75*
1
Playing DivX® VOD content
DivX® playback
Press C/D to select desired DivX® file.
!"#$
%&'( &)*
When PLAY has been pressed after displaying
the file browser, playback begins automatically
starting from the first file. In this case, if the first
file is a JPEG file, the first JPEG file is played
back. If the first file is a DivX® file, the first DivX®
file is played back. If the first file is an MP3/WMA
file, only MP3/WMA file are played back in order.
If there is no file at a root directory, playback does
not begin automatically.
2
▲/▼
ENTER
STOP
PLAY
®
Press ENTER or PLAY. The selected DivX
movie will be played back on the screen.
DivX® VOD content is protected by DRM (Digital Rights
Management) system. This restricts playback of content to
specific registered devices.
If the incorrect DRM file is
loaded, “Authorization
Error This player is not
authorized to play this
video.” will appear on the
screen.
When you attempt to play
DivX® VOD, the number of
plays is limited and the right message will appear on
the screen. If you wish to play it, select “YES”.
• If the number of plays goes over the limit, then
“Rental Expired” will be displayed, in this case the
file will not be played.
Notes:
• In order to play DivX® VOD content on this unit, you first need
to register the unit with registration code. See page 69 .
• This unit cannot playback the DivX® VOD content on the USB
Mass Storage.
3
Press STOP to end playback.
The file browser appears on the
screen. If you want to watch the
other file, repeat steps 1 ~ 2.
60
2I40301A-En_p60-69
60
21/3/06, 9:45 AM
▲/▼/ /
ENTER
PLAY
SKIP
/
+,
75*
1
Repeat playback (CD/USB)
In the file browser, press B/A or C/D to select
“Repeat” during stop mode.
Folder-1
Folder-2
MP3-1
MP3-2
+,
75*
1
Random playback (CD/USB)
In the file browser, press B/A or C/D to select
“Mode” during stop mode.
Select Files
Repeat
:Off
Mode
:Off
MP3-3
2
Press ENTER to select “Track” or “All”.
Folder-1
Folder-2
MP3-1
MP3-2
MP3 3
Press ENTER to select “Random”.
Select Files
Repeat
:Track
Mode
:Off
Press PLAY.
The unit automatically starts repeat
playback after finishing the current
track.
To resume normal playback
Select Repeat : “Off” in step 2.
3
!"
Press PLAY.
The Random playback will start.
To resume normal playback
Select Mode : “Off” in step 2.
Notes:
• The program is canceled when you open the disc tray or
turn the power off.
• In case of Audio CD, the function of A-B Repeat can be
used. See “A-B Repeat playback” # .
• Track repeat function is canceled whenever SKIP
or
is pressed.
Advanced playback (DVD)
3
2
61
2I40301A-En_p60-69
61
21/3/06, 9:45 AM
Advanced playback (DVD)
MP3/WMA/JPEG/DivX® and Audio
CD operation (Continued)
▲/▼/ /
ENTER
PLAY
+,
75*
1
Program playback (CD/USB)
In the file browser, press B/A or C/D to select
“Edit Mode”, then press ENTER.
Folder-1
Folder-2
MP3-1
Repeat
:Off
Mode
:Off
4
Press C/D to select “Program View”, then
press ENTER. Program View shows only the
programed files that you have added in Step 2.
Folder-1
Folder-2
Edit Mode
MP3-2
MP3 3
When “Edit Mode” is black color,
you can mark the files which you
want to add into Program list.
2
Press B/A or C/D to select the file you want to
add into the program list.
Folder-1
Folder-2
MP3-1
MP3-2
MP3-3
WMA-1
WMA 2
Repeat
:Off
Mode
:Off
Edit Mode
Program View
Add To Program
5
In the Program View, press PLAY. The files
start to playback in programmed order that
were added by you.
To remove file from program list
In the Edit Mode, switch to Program View. Select the files
you want to remove, then press ENTER. Select “Clear
Program” and press ENTER. Marked file is removed
from program list.
JPEG Preview
62
62
JPEG Preview
Program View
• When you finish storing all the files
you want into the Program list,
select “Edit Mode” again and press
ENTER to release edit mode.
2I40301A-En_p60-69
Add To Program
JPEG Preview
Press B/A or C/D to select “Add To Program”.
Then press ENTER. All marked files are added
into the program list.
Folder-1
Folder-2
MP3-1
MP3-2
MP3-3
WMA-1
WMA-2
Edit Mode
Press ENTER. Selected file was
marked.
Repeat this procedure to select the
other files.
3
Browser View
MP3-1
MP3-2
MP3-3
WMA-1
WMA-2
WMA-3
Edit Mode
Program View
21/3/06, 9:45 AM
Function setup (DVD)
Customizing the function settings
You can change the default settings to customize performance
to your preference.
C/D/B/A
ENTER
RETURN
SETUP
DVD
VCD
CD
1
Setting procedure
Press SETUP during stop mode.
The following on-screen display
appears.
Parental
DRC
E.B.L.
Menu
5
• Repeat steps 3 ~ 5 to change
: Off
English
other option.
QSound
TV
Subtitle
Screen
Set Password
: 4:3
On
English
Output
Display
Audio
• To select another section, go
: Interlace
English
On
back to step 2 by pressing B
repeatedly.
Picture Mode
DivX(R) :VOD
Auto
2
JPEG Interval
: 5 Seconds
Screen Saver
: On
Press C or D to select the desired section, then
press B or A.
Parental
DRC
Menu
E.B.L.
Change the selection using C or D, by referring
to the corresponding pages $# ~ 69 .
Press ENTER to save the setting.
6
To clear SETUP screen, press SETUP or
RETURN.
: Off
English
QSound
Subtitle
TV
Screen
Set Password
: 4:3
On
English
Output
Audio
Display
: Interlace
English
On
Picture Mode
DivX(R) :VOD
Auto
3
JPEG Interval
: Off
Screen Saver
: On
First option will be highlighted. Press C or D
to select the desired option.
Parental
DRC
Menu
E.B.L.
: Off
English
Output
Audio
Display
Function setup (DVD)
QSound
Subtitle
TV
Screen
Set Password
: 4:3
On
English
: Interlace
English
On
Picture Mode
DivX(R) :VOD
Auto
4
JPEG Interval
: Off
Screen Saver
: On
Then press A or ENTER. The selectable
settings will appear.
Parental
DRC
Menu
E.B.L.
: Off
English
QSound
Subtitle
TV
Screen
Set Password
: On
English
Output
Audio
Display
: Interlace
English
On
Picture Mode
DivX(R) :VOD
Auto
JPEG Interval
: Off
Screen Saver
: On
63
2I40301A-En_p60-69
63
21/3/06, 9:45 AM
Function setup (DVD)
Customizing the function settings (Continued)
Setting details
Section
Option
Details
Menu
Subtitle
Audio
To select the language of “Menu”, “Subtitle” and
“Audio” if more than one language are available on
the disc.
E.B.L.
To select On or Off for E.B.L. (Enhanced Black
Level).
TV Screen
To select a picture size according to the aspect
ratio of your TV.
Display
To turn on or de-activate the operational status display on the screen.
Picture Mode
To select a preferred picture mode from “Video”,
“Film” or “Auto”.
JPEG Interval
To select a preferred setting for the slide show playback.
Screen Saver
To select On or Off for Screen Saver function.
DRC
To select On or Off for DRC (Dynamic Range Control).
QSound
To select On or Off for QSound.
Digital Out
To select an output sound format corresponding to
your system connection.
Parental
To select a preferred parental level for the parental
setting.
Password
Input 4-digit password to set the parental level.
HD Jpeg
To select On or Off for HD Jpeg mode.
Output
To select a preferred video output signal from “Interlace” or “Progressive”.
DivX(R) VOD
To display your 8-character registration code.
Page
$#
$$
$%
$&
69
64
2I40301A-En_p60-69
64
21/3/06, 9:46 AM
Parental
DRC
E.B.L.
Menu
: English
Off
Parental
DRC
Menu
E.B.L.
: Off
English
QSound
TV
Subtitle
Screen
Set Password
: 4:3
On
English
QSound
Subtitle
TV
Screen
Set Password
: English
On
4:3
Output
Display
Audio
Output
Audio
Display
: English
Interlace
On
: English
Interlace
On
Picture Mode
DivX(R) :VOD
Auto
Picture Mode
DivX(R) :VOD
Auto
JPEG Interval
: 5 Seconds
JPEG Interval
: Off
Screen Saver
: On
Screen Saver
: On
Menu, Subtitle, Audio
E.B.L.
You can select the language of “Menu”, “Subtitle” and
“Audio” if more than one languages are recorded onto
the disc.
English, Francais, Espanol:
The selected language will be heard or seen.
Other:
Other language can be selected (see the
“Language code list” 71 ).
Original: (Audio)
The unit will select the first priority language of
each disc.
Off: (Subtitle)
Subtitles do not appear.
Off: Standard grey scale (7.5 IRE cut off)
On: Enhanced grey scale (0 IRE cut off)
TV Screen
You have the following screen sizes to choose from:
4:3
(Letter box):
Select this mode when connecting to a conventional TV. When playing back a wide screen-DVD
disc, it displays the wide picture with black bands
at the top and bottom of screen.
4:3
(Pan scan):
It displays the wide picture on the whole screen
with left and right edges automatically cut off.
16:9
(Wide):
Select this mode when connecting to a widescreen TV. A wide screen picture is displayed full
size.
Function setup (DVD)
Notes:
• If the selected language is not recorded on the disc, the
first-priority language is selected.
• If you want to change the OSD language, you can perform
it by VCR MENU & .
To select the black level of playback pictures, set your
preference and monitor’s ability.
Note:
If the DVD disc is not formatted in the pan & scan style, it
displays 4:3 style.
65
2I40301A-En_p60-69
65
21/3/06, 9:46 AM
Function setup (DVD)
Customizing the function settings (Continued)
Setting details
Display
JPEG Interval
On screen display can be switched on or off when you
press the buttons.
Off: On screen displays do not appear when you
press any buttons.
On: On screen displays appear when you press
the buttons (factory setting).
There are two types of source content in pictures
recorded in DVD video discs: film content (pictures
recorded from films at 24 frames per second) and
video content (video signals recorded at 30 frames per
second). Make this selection according to the type of
content being viewed.
Film:
Off:
Plays back one file at a time.
5 Seconds:
Plays back images in the form of a slide show at
5 second intervals.
Picture Mode
Auto:
You can continuously playback all JPEG files
automatically.
After the selection below, the disc will start playback on
which JPEG files have been recorded.
Select this position normally.
The DVD player automatically detects
source content, film or video, of
playback source, and converts that
signal in the progressive output format
in an appropriate method.
The DVD player converts film content
pictures in the progressive output
format appropriately. Suitable for
playback of film content pictures. The
progressive output feature will be most
effective under this selection.
Video: The DVD player filters video signal,
and converts it in the progressive
output format appropriately.
Suitable for playback of video content
pictures.
10 Seconds:
Plays back images in the form of a slide show at
10 second intervals.
15 Seconds:
Plays back images in the form of a slide show at
15 second intervals.
Screen Saver
The screen saver operates when you leave the unit
in DVD stop mode for approx. five minutes.
The screen will repeatedly get dark gradually and
back to normal.
Off:
Screen Saver function is invalidated.
On:
Screen Saver function is made effective.
Note:
Depending on the disc, pictures may be cut off or
doubled. In this case, select “Video”.
66
2I40301A-En_p60-69
66
21/3/06, 9:46 AM
Parental
Menu
E.B.L.
DRC
: English
Off
Subtitle
TV
QSound
Screen
Set Password
: Off
4:3
English
Output out
Audio
Display
Digital
: English
Interlace
On
PCM
Digital Out
Selected the output sound format corresponding to your
system connection.
Picture Mode
DivX(R) :VOD
Auto
JPEG Interval
: 5 Seconds
Screen Saver
: On
PCM:
Select when connected to a 2 channel digital
stereo amplifier.
Bitstream:
Disc audio bitstream data will be output.
DRC
DRC (Dynamic Range Control) enables you to control
the dynamic range so as to achieve a suitable sound for
your equipment.
Off:
It plays back at the recording level on the disc.
On:
Loud sound such as explosion or similar is toned
down slightly when played back. This makes it
suitable for when it is connected to a stereo.
Notes:
• When you make a connection to a TV, or Dolby
Surround Pro Logic or stereo system via the analog
audio jacks, select “PCM” or “Bitstream”.
• If apply HDMI connection to TV, make sure to select
“PCM”, audio signal passing to TV via HDMI cable.
Notes:
• This function works only during playback of Dolby Digital
recorded discs.
• The level of Dynamic Range Reduction may differ
depending on DVD video disc.
Function setup (DVD)
QSound
This DVD video player equipped with a “QSound”. It can
produce the effect of being in a cinema or a concert hall.
Off: The QSound is disengaged.
On: The QSound operates.
Notes:
• The QSound setting can also be changed with AUDIO
on the remote control ## .
• This function works only when the disc recorded with
Dolby Digital is played back.
• When this function works, the volume might changed.
• When the voice is distorted, turn off QSound.
67
2I40301A-En_p60-69
67
21/3/06, 9:46 AM
Function setup (DVD)
Customizing the function settings (Continued)
Setting details
DRC
Menu
E.B.L.
Parental
: English
Off
QSound
Subtitle
TV
Password
Screen
: Change
On
4:3
English
Audio
Display
HD
Jpeg
: English
Off
On
Picture Mode
Output
: Auto
Interlace
JPEG Interval
DivX(R)
VOD
: Display
5 Seconds
Screen Saver
: On
Parental control setting
Some discs are specified not suitable for children.
Such discs can be limited not to play back with the
unit.
1) Press C or D to select “Parental”, then press
ENTER. “Enter Password” screen will appear.
2) Press “0000” using Number buttons (0–9).
(Please note, this is pre-setting password of this
unit). Then press ENTER. The parental level list will
appear.
• Level Off: The parental control setting does not
function.
• Level 8: Virtually all DVD software can be
played back.
• Level 1: DVD software for adults cannot be
played back.
3) Press C or D to select from the level 1 to level 8.
The limitation will be more severe as the level
number is lower. Then press ENTER.
4) Press OPEN/CLOSE to activate Parental control
setting.
Notes:
• Depending on the discs, the unit cannot limit
playback.
• Some discs may not be encoded with specific rating
level information though its disc jacket says “adult.” For
those discs, the age restriction will not work.
• The password is required every time when you change
the parental level.
• If you input a wrong number, press CLEAR.
If you forget the password...
1) Press OPEN/CLOSE to open the disc tray.
2) Remove the disc.
3) Press OPEN/CLOSE again to close the disc tray.
“No Disc” appears on the screen.
4) While holding 7 down on the remote control and
at the same time press STOP on the front panel.
“Password Clear” appears on the screen. Now the
password has been returned to the initial value
(“0000”).
HD Jpeg
This DVD/VCR equipped with a “HD Jpeg”. It can display
the HD resolution JPEG images when the DVD/VCR is
connected to a HDTV using HDMI.
On:
Select when you connect the DVD video player to
a HDTV via HDMI OUT jack. JPEG images is displayed in suitable picture quality (480p, 720p or
.
1080i)
Off:
The picture processing quality is fixed to 480p.
Notes:
• When the DVD/VCR is not connected to a TV using
HDMI, you cannot select “On”.
• When HD Jpeg is set to “On”, zoom function is prohibited
and component video outputs disabled when 480p, 720p
or 1080i is selected.
Set the new password
1) Press C or D to select “Password”, then press
ENTER. “Enter Current Password” screen will
appear.
2) Press Number buttons (0–9) to input the current
password (If the password has not been set yet
after you purchase this unit, it is “0000”).
3) Then press ENTER. “Enter New Password” screen
will appear. Press Number buttons (0–9) to input
the new password.
4) Press ENTER. Now your new password has been
set. Be sure to remember this number!
68
2I40301A-En_p60-69
68
21/3/06, 9:46 AM
Output
You can select the video output signal of the DVD
video player to the TV from “Interlace” or “Progressive”.
Interlace:
Select when connecting to a composite TV or
a TV equipped with component video inputs
but progressive scan is not compatible.
Progressive:
Select when connecting to a TV equipped
with component video inputs and progressive
scan compatible.
Warning:
Once “Progressive” is selected when connecting to a
TV progressive scan incompatible, no image will be
seen on the video display.
In this case, you must reset the unit by pressing STOP
on the front panel for five seconds. The video output
will be restored to “Interlace” setting, and a picture will
once again be seen on a conventional analog display.
Function setup (DVD)
Notes:
• Some discs may not be played back with the progressive
scanning mode correctly because of the disc characteristics or recording condition.
• Once Progressive scan on, S-video output is disabled.
DivX® VOD
In order to play DivX® VOD (Video On Demand)
content on this unit, you first need to register the unit
with your DivX® VOD content provider. You do this by
generating a DivX® VOD registration code, which you
submit to your provider.
Press C or D to select “DivX(R) VOD”. Then press
ENTER. Your 8-character registration code is
displayed. Make a note of the code as you will need
it when you register with a DivX® VOD provider.
Then press ENTER to select Done.
Note:
If each setup (pages $# ~ 69 ) has been completed, the unit
can always be worked under the same conditions (especially with DVD discs).
Each setup will be retained in the memory even if you turn
the power off.
69
2I40301A-En_p60-69
69
21/3/06, 9:46 AM
Function setup (DVD)
Temporary disabling of rating level by DVD disc
Depending on the DVD disc, the disc may try to temporarily cancel the rating
level that you have set.
It is up to you to decide whether to cancel the rating level or not.
0–9
ENTER
RETURN
PLAY
OPEN/CLOSE
DVD
Temporary disabling of rating level by DVD disc
1
Load a DVD disc and press PLAY or OPEN/
CLOSE on the unit "% .
2
If the DVD disc has been designed to temporarily cancel the Rating level, the screen which
follows the “Reading” screen will change,
depending on which disc is played. If you
select “YES” with the ENTER key, password
input screen will then appear.
3
Enter the password with Number buttons (0–9).
Then press ENTER.
Note:
This temporary cancellation of rating level will be kept until the
disc is ejected.
When the disc is ejected, the original rating level will be set again
automatically.
To exit from the entry, press
RETURN.
4
Playback will commence if the entered
password was correct.
70
2I40301A-En_p70-BACK
70
21/3/06, 9:46 AM
Others
Language code list
Enter the appropriate code number for the initial settings “Menu”, “Subtitle” and/or “Audio” $# .
Language Name Code
Language Name Code
Language Name Code
Abkhazian
1112
Fiji
1620
Lingala
2224
Singhalese
2919
Afar
1111
Finnish
1619
Lithuanian
2230
Slovak
2921
Afrikaans
1116
French
1628
Macedonian
2321
Slovenian
2922
Albanian
2927
Frisian
1635
Malagasy
2317
Somali
2925
Amharic
1123
Galician
1722
Malay
2329
Spanish
1529
Arabic
1128
Georgian
2111
Malayalam
2322
Sundanese
2931
Armenian
1835
German
1415
Maltese
2330
Swahili
2933
Assamese
1129
Greek
1522
Maori
2319
Swedish
2932
Aymara
1135
Greenlandic
2122
Marathi
2328
Tagalog
3022
Azerbaijani
1136
Guarani
1724
Moldavian
2325
Tajik
3017
Bashkir
1211
Gujarati
1731
Mongolian
2324
Tamil
3011
Basque
1531
Hausa
1811
Nauru
2411
Tatar
3030
Bengali; Bangla 1224
Hebrew
1933
Nepali
2415
Telugu
3015
Bhutani
1436
Hindi
1819
Norwegian
2425
Thai
3018
Bihari
1218
Hungarian
1831
Oriya
2528
Tibetan
1225
Breton
1228
Icelandic
1929
Panjabi
2611
Tigrinya
3019
Bulgarian
1217
Indonesian
1924
Pashto, Pushto 2629
Tonga
3025
Burmese
2335
Interlingua
1911
Persian
1611
Turkish
3028
Byelorussian
1215
Irish
1711
Polish
2622
Turkmen
3021
Cambodian
2123
Italian
1930
Portuguese
2630
Twi
3033
Catalan
1311
Japanese
2011
Quechua
2731
Ukrainian
3121
Chinese
3618
Javanese
2033
Rhaeto-Romance 2823
Urdu
3128
Corsican
1325
Kannada
2124
Romanian
2825
Uzbek
3136
Croatian
1828
Kashmiri
2129
Russian
2831
Vietnamese
3219
Czech
1329
Kazakh
2121
Samoan
2923
Volapük
3225
Danish
1411
Kirghiz
2135
Sanskrit
2911
Welsh
1335
Dutch
2422
Korean
2125
Scots Gaelic
1714
Wolof
3325
English
1524
Kurdish
2131
Serbian
2928
Xhosa
3418
Esperanto
1525
Laothian
2225
Serbo-Croatian 2918
Yiddish
2019
Estonian
1530
Latin
2211
Shona
2924
Yoruba
3525
Faroese
1625
Latvian, Lettish 2232
Sindhi
2914
Zulu
3631
Others
Language Name Code
71
2I40301A-En_p70-BACK
71
21/3/06, 9:46 AM
Others
Troubleshooting
Before calling a service technician, please check the following table for a possible cause of the symptoms and some solutions.
Symptoms
Solutions
Page
DVD/VCR
• Make sure the power cord is plugged in.
• Try another AC outlet.
• Unplug unit, then plug it back in.
• Select the DVD or VCR mode before operating.
• Antenna connection is not correct or antenna cable is disconnected.
• The video channel is not in the correct position or the TV is not set to the video
channel 3 or 4.
• Check the unit is connected correctly.
• The video input selector of the TV is not set to VIDEO. Set to VIDEO (or
equivalent).
• Channel is set to the external mode.
• Press HDMI to turn off the HDMI mode.
5
–
5
35,47
16~19
27
No sound.
• Check the unit is connected correctly.
• Check the input selector of the amplifier is set properly.
• The unit is in the Special playback mode.
16~26
–
36,49
The remote control does not function.
• Aim the remote control at the remote sensor.
• Operate within Approx. 7 Meters or reduce the light in the room.
• Clear the path of the beam.
• The batteries are weak. Replace the batteries.
• Check the batteries are inserted correctly.
No Cable TV reception.
• Check all Cable TV connections.
• Station or Cable TV system problems, try another station.
18,19
TV recording does not work.
• The erase prevention tab of the video cassette is broken off.
• The unit is in the external input mode.
34,39
Timer recording does not work.
• The time is not set correctly.
• The recording start/end time is not set correctly.
• The TIMER REC has not been pressed ( is not lit).
29~31
42
42
Noise bars on screen.
• Tracking adjustment beyond range of automatic tracking circuit. Try Manual
tracking adjustment.
• Video heads are dirty.
• The tape is worn or damaged.
DVD/VCR does not operate.
No picture.
16~26
–
–
22
13
VCR
36
36
–
DVD
Display is not shown in your language.
• Select proper language in the menu options.
65
Playback doesn’t start.
• No disc is inserted.
• The disc may be dirty. Clean up the disc.
• The unit cannot play DVD-ROMs, etc.
47
7
7
Stopping playback, slow-motion play, repeat
play, or memory play, etc. cannot be
• Some discs may not do some of the functions.
performed.
–
No picture, or the screen is blurred or divided • The PROGRESSIVE scan is “On” although the unit is connected to a TV
via the VIDEO OUT or the S-VIDEO OUT jack.
into two parts.
69
No 4:3 (16:9) picture.
• The setup does not match your TV.
65
No on-screen display.
• Set Display to “On”.
66
No surround sound.
• The setup does not match your stereo system.
67
The unit or remote operation key is not
functioning.
Playback does not start when the title is
selected.
• Turn off the unit and unplug the AC power cord for several minutes, then replug it.
–
• Check the Parental setup.
68,70
Audio soundtrack and/or subtitle language
is not changed when you playback a DVD.
• Multilingual language is not recorded on the DVD disc.
55,56
No subtitle.
• Some discs have no subtitles.
• Subtitles are cleared. Press SUBTITLE.
56
Angle cannot be changed.
• Multi-angles are not recorded on the DVD disc.
54
“X” appears on the screen.
• The function is prohibited with the unit or the disc.
49
72
2I40301A-En_p70-BACK
72
21/3/06, 9:46 AM
Specifications
General
Power supply
Power consumption
Weight
Dimensions
Tuner
Antenna input/output
RF channel output
Color system
Video head
Audio track
Hi-Fi frequency response
Hi-Fi dynamic range
FWD/REV time at 25˚C (77˚F)
Applicable disc
Frequency range
S/N ratio
Harmonic distortion
Wow and flutter
Operating conditions
AC 120 V 60 Hz
Operation: 20 W, Stand by: 2 W
7.7 lbs (3.5 kg)
Width: 16-15/16 inches (430.6 mm)
Height: 3-9/16 inches (89.7 mm)
Depth: 9 inches (228.7 mm)
181 channel freq. synthesized
VHF
2-13
UHF
14-69
Cable TV 113 Channels
UHF/VHF In/Out: 75 Ω coaxial
Channel 3 or 4, Switchable
NTSC
4 Rotary heads
Hi-Fi sound - 2 Tracks / MONO sound - 1 Track
20 Hz to 20 kHz
More than 90dB
Approx. 1 minute and 48 seconds (with T-120 Cassette Tape)
DVD (12 cm, 8 cm), CD (12 cm, 8 cm)
DVD: 4 Hz-22 kHz, CD: 4 Hz-20 kHz
85dB (DVD)
0.06% (DVD)
Less than 0.01% Wrms
Temperature: 5˚C-40˚C (41˚F-104˚F), Operating status: Horizontal
Input/Output
DVD/VCR
Video input
Video output
Audio input
Audio output
1.0 V (p-p), 75 Ω, negative sync., pin jack x 2
1.0 V (p-p), 75 Ω, negative sync., pin jack x 1
–8 dBm, 50 kΩ, negative sync., pin jack (L/R) x 2
–8 dBm, 1 kΩ, negative sync., pin jack (L/R) x 1
DVD
S-video output
Component video output
Others
Audio output (COAXIAL DIGITAL)
Audio output (ANALOG)
(Y) 1.0 V (p-p), 75 Ω, negative sync., Mini DIN 4-pin x 1
(C) 0.286 V (p-p), 75 Ω
(Y) 1.0 V (p-p), 75 Ω, negative sync., pin jack x 1
(PB)/(PR) 0.7 V (p-p), 75 Ω, pin jack x 2
0.5 V (p-p), 75 Ω, pin jack x 1
–12 dBm, 1 kΩ, pin jacks (L/R) x 1
Supplied accessories
Audio/video cable ................................................. 1
Remote control (SE-R0221) ................................. 1
Batteries (R03/AAA) ............................................. 2
75 Ω coaxial cable ................................................ 1
• This model complies with the above specifications.
• Designs and specifications are subject to change without notice.
• This model may not be compatible with features and/or specifications that may be added in the future.
73
2I40301A-En_p70-BACK
73
21/3/06, 9:46 AM
Others
- IMPORTANT CANADIAN WARRANTY INFORMATION
GARANTIE CANADIENNE
STANDARD WARRANTY
TYPE OF SET
DVD Player
DVD/VCR Combination
Home Theatre in a Box
DVD Recorder
Portable DVD
WARRANTY PERIOD
12 MONTHS
CANADIAN WARRANTY
Toshiba of Canada Limited (TCL) makes the following
limited warranties to original consumers in Canada.
Please retain your “Bill of Sale” as proof of purchase.
To obtain a “Canadian Warranty” please register
online at www.toshiba.ca.
Canadian Warranty Information
Should service be required on this unit during the one year
warranty period, TCL's option will be to repair or exchange the
defective unit. It will be necessary to follow this procedure:
Contact: Toshiba of Canada Limited at the Consumer
Electronics Group, customer support line.
Phone: 1-800-268-3404
Email:
[email protected]
All in-warranty repairs must be made by an authorized TCL
service centre.
For service exchange TCL will arrange to have the unit picked
up by courier and a replacement unit will be returned via same
courier. (Note: A major credit card number will be required as a
charge of $25.00 will apply if no fault is found with the unit.)
During the first 3 months of ownership, a new unit will be supplied as a replacement. During the remainder of the warranty
period a service-renewed unit will be supplied.
The original “Bill of Sale” must be provided as proof of purchase (it will be returned with the replacement unit.)
This 12-month warranty will be strictly adhered to.
Out of warranty units should be repaired by a TCL authorized
service centre.
Note: It is the responsibility of the owner to ensure proper
packaging. Should damage in shipping occur, due to poor
packaging, a charge back for the repair will result.
This warranty applies to the original purchaser only and is not
transferable.
This warranty does not apply to sets that have been subjected
to misuse, neglect, accident, physical damage or acts of
nature.
Sets with the serial number removed, altered, replaced or
defaced will not be covered by this warranty.
The warranties from TCL are effective only if the product is
purchased in Canada from an authorized TCL dealer and
operated in Canada.
Products utilized for rental or commercial purposes are not
covered by this warranty.
This warranty is in lieu of all other warranties, guaranties or
agreements, whether expressed or implied, and no person,
agent distributor, dealer, service centre or company is authorized to change, modify or extend its terms in any manner
whatsoever.
GARANTIE NORMALE
TYPE D’APPAREIL
DURÉE DE LA GARANTIE:
Lecteur DVD
DVD/magnétoscope combo
Cinéma maison dans une boîte
Enregistreur DVD
DVD Portatif
12 MOIS
GARANTIE CANADIENNE
1) Toshiba du Canada Limitée (TCL) offre au Canada les
garanties limitées suivantes aux consommateurs originaux. Veuillez conserver votre « facture » comme preuve
d’achat. Pour obtenir une garantie canadienne,
veuillez vous inscrire en ligne à www.toshiba.ca
Information sur la garantie Canadienne
Si vous avez besoin de service sur cet appareil au cours le
l'année de garantie, Toshiba du Canada Limitée aura l'option
de réparer ou échanger l'appareil défectueux. Vous devrez
suivre la procédure suivante:
Contact: Toshiba du Canada Limitée au Groupe Électronique
aux consommateurs, service à la clientèle.
Tél:
1-800-268-3404
Courriel: [email protected]
Toutes les réparations au cours de la garantie doivent être faites
par un centre de service autorisé Toshiba.
Pour un échange TCL s'assurera qu'un service de courrier
ramassera l'unité et qu'un appareil de remplacement soit
expédié par le même service de courrier.
(Note: Un numéro de carte de crédit sera requis car une
charge de 25,00$ sera appliquée si toutefois l’appareil n’avait
aucun problème de fonctionnement.)
Une nouvelle unité sera fournie comme remplacement durant
les premiers 3 mois de propriété. Par contre durant la balance
de la garantie une unité remise à neuf sera fournie.
La «facture originale doit être fournie comme preuve d’achat
(elle vous sera retournée avec l’unité de remplacement.)
Cette garantie de 12 mois sera strictement adhérée.
Les unités hors de garantie devraient être réparées par un
centre de service autorisé Toshiba.
Note: C’est la responsabilité du propriétaire de s’assurer que
l’emballage est adéquat. Vous serez facturé pour toutes réparations causées par des dommages encourus à cause d’un
emballage non adéquat.
Cette garantie est octroyée à l’acheteur initial et n’est pas
transférable. Cette garantie ne s’aplique pas aux appareils qui
ont été sujets aux abus, négligences, accidents, dommages
physiques ou actes naturels.
Les appareils dont le numéro de série a été enlevé, altéré,
remplacé ou barbouillé ne sont pas couverts par cette
garantie.
Les garanties de TCL sont valides seulement sur les unités
sont achetées et utilisées au Canada d'un marchand autorisé
TCL.
Cette garantie ne couvre pas les produits de location ou à
usage commercial. Cette garantie remplace toutes autres
garanties ou ententes exprimées ou sous-entendues. Aucune
personne, agent, distributeur, concessionaire ou compagnie
n’est autorisé à changer, modifier ou prolonger les termes de
cette garantie de quelque façon que ce soit.
Toshiba of Canada Limited 191 McNabb Street Markham, Ontario L3R 8H2
74
2I40301A-En_p70-BACK
74
21/3/06, 9:46 AM
Memo
Others
...................................................................................................................................
...................................................................................................................................
...................................................................................................................................
...................................................................................................................................
...................................................................................................................................
...................................................................................................................................
...................................................................................................................................
...................................................................................................................................
...................................................................................................................................
...................................................................................................................................
...................................................................................................................................
...................................................................................................................................
...................................................................................................................................
...................................................................................................................................
...................................................................................................................................
...................................................................................................................................
...................................................................................................................................
...................................................................................................................................
...................................................................................................................................
...................................................................................................................................
...................................................................................................................................
...................................................................................................................................
...................................................................................................................................
...................................................................................................................................
...................................................................................................................................
...................................................................................................................................
...................................................................................................................................
...................................................................................................................................
...................................................................................................................................
...................................................................................................................................
...................................................................................................................................
...................................................................................................................................
...................................................................................................................................
...................................................................................................................................
...................................................................................................................................
...................................................................................................................................
...................................................................................................................................
...................................................................................................................................
75
2I40301A-En_p70-BACK
75
21/3/06, 9:46 AM
ColorStream and ColorStream Pro are registered trademarks of Toshiba America Consumer Products, L.L.C.
Printed in Thailand
2I40301A-En_p70-BACK
76
21/3/06, 9:46 AM
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement