Ultra Start 450 SERIES Automobile Alarm User Manual

Add to my manuals

advertisement

Ultra Start 450 SERIES Automobile Alarm User Manual | Manualzz
REV.2007.07.03
450 SERIES
ADVANCED VEHICLE SECURITY SYSTEM
TM
OWNER'S GUIDE
www.ultrastarters.com
FCC ID NOTICE
This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions:
1. This device may not cause harmful interference, and
2.This device must accept any interference received, including interference that may cause undesired operation.
CAUTION: Changes or modifications not expressly approved by the part responsible for compliance void the user’s authority to operate
this devise.
450 SERIES
OWNER'S MANUAL
PAGE 2
SYSTEM
PROGRAMMING
TABLE
OF CONTENTS- Menu 1
Product Warranty...........................................................Page 3
Remote Functions Quick View......................................Pages 4
Second Car Operation
Page 4
Valet Mode &
Page 5
Emergency System Override
Page 5
Alarm Functions.............................................................Pages 6-9
Arm System
Page 6
Trunk Release*
Page 6
Disarm System
Page 7
Priority Unlock*
Page 7
Panic
Page 8
Silent Arm/Disarm
Page 8
Car Finder
Page 8
Auxiliary #1 (Ch 4)*
Page 9
Ignition Auto Locks*
Page 9
Passive Arming*
Page 9
Starter Disable*
Page 9
Dome Light Supervision*
Page 9
Shock Sensor.................................................................Page 10
Shock Sensor Programming
Shock Sensor Adjustments
Diagnostics.....................................................................Page 11
Diagnostics Chart
Overload Chart
Additional LED Flashes
Contact Information ......................................................Page 12
PAGE 3
WARRANTY - Menu 1
SYSTEM PROGRAMMING
450 SERIES
OWNER'S MANUAL
Applicated Security Technologies, Inc. ("AST") promises to the original purchaser to repair or replace with a
comparable reconditioned model any AST control module ("module") excluding without limitation the any
other accessories, including but not limited to the antenna, remote, siren and wiring harness, proves to be
defective in workmanship or material under reasonable use during the lifetime of the vehicle it was originally
installed, provided the following conditions have been met: the module was professionally installed and
serviced by an authorized AST dealer; the unit will be professionally reinstalled in the vehicle in which it was
originally installed by an authorized AST dealer; the warranty information card was sent to AST within 10
days of the original installation date. Any warranty returns include a warranty return authorization number
issued by AST, original bill or sale and be pre-paid shipped directly to AST. After an initial period of 2 years
from the date of installation, AST reserves the right, at its sole discretion, to charge a warranty processing
fee of $30.00 USD. AST does not cover the cost for return freight on warranty items, this cost is the sole
responsibility of the purchaser.
All components included with the original packaged unit other than the module, including but not limited to
the siren, antenna and the remote transmitters, carry a one-year warranty from the date of purchase of the
same. Any warranty returns on components must include a warranty return authorization number issued by
AST, original bill or sale and be pre-paid shipped directly to AST. This warranty is non-transferable and is
automatically void if: the original purchaser has not completed the warranty card and mailed it within ten
(10) days of the date of purchase to the address listed on the card; the unit's date code or serial number is
defaced, missing or altered; the unit has been modified or used in a manner contrary to its intended
purpose; the unit has been damaged by accident, unreasonable use, neglect, improper service, installation
or other causes not arising out of defects in materials or construction. The warranty does not cover damage
to the unit caused by installation or removal of the unit. AST, at its sole discretion, will determine what
constitutes excessive damage and may refuse the return of any unit with excessive damage, including, but
not limited to, overloading, moisture and physical damage.
To the maximum extent allowed by law, any and all warranties are excluded by the manufacturer and each
entity participating in the stream of commerce therewith. This exclusion includes but is not limited to, the
exclusion of any and all warranty of merchantability and/or any and all warranty of fitness for a particular
purpose and/or any and all warranty of non-infringement or patents, in the United States of America and/or
abroad. Neither the manufacturer or any entities connected therewith shall be responsible or liable for any
damages whatsoever, including but not limited to, any consequential damages, incidental damages,
damages for loss of time, loss of earnings, commercial loss, loss of economic opportunity and the like.
Notwithstanding the above, manufacturer does offer a limited warranty to replace or repair the control
module as describe above.
Some states do not allow limitations on how long an implied warranty will last or the exclusion or limitation
on how long an implied warranty will last or the exclusion or limitation of incidental or consequential
damages. This warranty gives you specific legal rights, and you may also have other rights, which vary
State to State.
450 SERIES
PAGE 4
OWNER'S MANUAL
BUTTON
LOCK
UNLOCK
SYSTEM
PROGRAMMING
- Menu 1
QUICK
VIEW
OPERATION CHART
BUTTON PRESS
CHIRP /
FLASH
SYSTEM FUNCTION
1 SEC
1
LOCK / ARM ALARM
3 SEC
1
ACTIVATE PANIC
PRESS THEN
RELEASE THEN
PRESS & HOLD
1
ACTIVATE CONSTANT LOCK
OUTPUT **
1 SEC
2
UNLOCK / DISARM
1 SEC
WHILE ALARM IS
TRIGGERED
NONE
TURNS OFF SIREN BUT ALARM IS
STILL ARMED
1 SEC
3
UNLOCK / DISARM
ALARM EVENT IN MEMORY
see alarm event memory chart
PRESS & HOLD FOR 1 5 SEC
1
ACTIVATES AUX OUTPUT
** PROGRAMMABLE OUTPUT - CHECK WITH INSTALLATION CENTER FOR DETAILS
PRESS & HOLD FOR 3
SEC
+
PRESS TOGETHER
THEN RELEASE
PRESS TOGETHER
THEN RELEASE
ON
ACTIVATES CAR FINDER
1
ACTIVATES SILENT ARM
2
ACTIVATES SILENT DISARM
NO SIREN CHIRPS - ACTS AS A TOGGLE - IF ARMED WILL DISARM, IF DISARMED WILL ARM
PRESS LOCK THEN
RELEASE FOLLOWED
BY PRESSING BUTTON
3 FOR 1 SECOND
1
ARMS / LOCKS AND TURNS OFF
SHOCK SENSOR
(FOR 1 ARM CYCLE ONLY)
BUTTON
BUTTON PRESS
CHIRP /
FLASH
SYSTEM FUNCTION
1 SEC
1
LOCK / ARM ALARM
3 SEC
1
ACTIVATE PANIC
PRESS THEN
RELEASE THEN
PRESS & HOLD
1
ACTIVATE CONSTANT LOCK
OUTPUT **
1 SEC
2
UNLOCK / DISARM
1 SEC
WHILE ALARM IS
TRIGGERED
NONE
TURNS OFF SIREN BUT ALARM IS
STILL ARMED
1 SEC
3
UNLOCK / DISARM
ALARM EVENT IN MEMORY
see alarm event memory chart
PRESS & HOLD FOR 1
- 5 SEC
1
ACTIVATES AUX OUTPUT
** PROGRAMMABLE OUTPUT - CHECK WITH INSTALLATION CENTER FOR DETAILS
450 SERIES
OWNER'S MANUAL
PAGE 6
SYSTEM
PROGRAMMING
- Menu 1
TRANSMITTER
FUNCTIONS
PRESS & RELEASE
ARM SYSTEM / LOCK DOORS
1
2
3
4
5
Press and release the Arm/ Lock button on the remote transmitter.
The park lights will flash and the siren/ horn will chirp one time.
The doors will lock and the Starter Disable will activate. (optional)
The LED will start flashing within five seconds.
Once Armed, the alarm can be triggered by the shock sensor (impact to
vehicle), door inputs (opening door / hood), turning on ignition.
NOTES:
- If a door is open or delay dome light is 30 seconds after arming, system with chirp 3
times to indicate door input is bypassed until door is closed or dome light turns off.
- If system is programmed for silent arming, siren will not chirp when arming, but park
lights will still flash.
- If system is in valet mode, doors will lock, but siren will not chirp and lights will not flash.
LED indicator will be on solid.
See Valet / Service Mode in this manual for further information
PRESS & HOLD
ACTIVATE TRUNK RELEASE
1 Press then HOLD the Disarm / Unlock button on the remote.
2 The park lights will flash and the siren will chirp two times.
3 The doors will unlock and the Starter Disable will deactivate. (optional)
4 The LEDs will stop flashing.
5 - Continue to HOLD until siren chirps again and trunk activates
6 - Release Button
NOTES:
- For safety, the trunk release will not active when ignition key is ON.
PAGE 7
TRANSMITTER
FUNCTIONS
SYSTEM
PROGRAMMING
- Menu 1
450 SERIES
OWNER'S MANUAL
PRESS & RELEASE
DISARM SYSTEM / UNLOCK DOORS
1
2
3
4
Press then release the Disarm / Unlock button on the remote.
The park lights will flash and the Siren will chirp Two times.*
The doors will unlock and the Starter Disable** will deactivate.
The LEDs will stop flashing.
NOTES:
- If the alarm was active (siren sounding), the first press of the unlock button will turn off
the siren and the second press will unlock / disarm.
- Siren will chirp 3 times if alarm was triggered while armed. See alarm diagnostics
section of manual for further information
- If system is programmed for silent disarm, siren will not chirp when disarming, park
lights will flash 2 times. Contact installer if you do not want this feature.
- If system is in valet mode, siren will not chirp and park lights will not flash but doors will
unlock. LED will be one SOLID. See Valet / Service Mode section of manual for
further information.
** Optional Feature may require additional parts
PRESS TWICE
DRIVER'S DOOR PRIORITY UNLOCK
1 Press then release the Disarm / Unlock button on the remote transmitter.
2 The park lights will flash and the siren will chirp two times.*
3 The driver's doors will unlock and the Starter Disable will deactivate. (optional)
4 The LEDs will stop flashing.
5 Press the Disarm / Unlock Button a second time within 3 seconds and the other
doors will unlock.
450 SERIES
PAGE 8
OWNER'S MANUAL
SYSTEM
PROGRAMMING
- Menu 1
TRANSMITTER
FUNCTIONS
PRESS HOLD
ACTIVATE PANIC MODE
1
2
3
4
5
Press and HOLD the Arm/ Lock button for three seconds.
The doors will lock and the Starter Disable will activate. (optional)
The park lights will begin to flash and the siren will activate.
To turn off panic, press Lock or Unlock buttons on remote.
If no button is pressed, Panic Alarm will sound up to 1 minute then turn off.
Panic Mode is a personal protection feature that allows you to activate your alarm from the
remote transmitter. This feature can be used to draw attention to your vehicle if you feel
threatened.
+
PRESS TOGETHER
SILENT ARM / SILENT DISARM
1 Press then release the Lock & Unlock buttons together.
2 If the system is DISARMED, it will Arm and Lock with no siren chirps and 1 light
flash.
3 If the system is ARMED, it will Disarm and Unlock with no siren chirps and 2 light
flash
.
PRESS & HOLD for 3 sec
CAR FINDER MODE
- PRESS & HOLD button number 4 on the remote transmitter for 3 seconds the release.
- Siren will chirp 5 times and lights will flash.
This feature helps in locating vehicle in a busy parking lot. It allows you hear and see your
vehicle from a distance.
450 SERIES
PAGE 10
OWNER'S MANUAL
SYSTEM
PROGRAMMING
SHOCK
SENSOR - Menu 1
SHOCK SENSOR ADJUSTMENTS
1 - ENTER SHOCK SENSOR ADJUSTMENT MODE
+
Press & HOLD Lock + Unlock buttons at the same time
Continue to hold for 3-5 seconds Until Siren Chirps 3 times
3 CHIRPS (Note: System will Arm or Disarm via silent arming prior to
entering adjustment mode)
2 - ADJUSTING SENSOR
Each time the lock button is pressed and released the sensitivity will
decrease by 1 level.
This is confirmed by a series of park light flashes & Siren Chirps
1 Flash / Chirp is the least sensitive setting
10 Flashes / Chirps is the most sensitive setting
Each time the unlock button is pressed and released the sensitivity will
increase by 1 level.
This is confirmed by a series of park light flashes & Siren Chirps
1 Flash / Chirp is the least sensitive setting
10 Flashes / Chirps is the most sensitive setting
3 - EXITING SENSOR ADJUSTMENT MODE
+
Press & HOLD Lock + Unlock buttons at the same time
(NOTE: Shock Sensor Adjustment Mode has an auto time out of
8 seconds)
ADDITIONAL LED FUNCTIONS
While the system is disarmed and the ignition is in the off position, the
LEDs will activate from the following triggers.
1) If the door is opened the LEDs will stay on until the door is closed.
2) If the hood is opened the LEDs will stay on until the hood is closed.
3) If the shock sensor detects vibration the LEDs will turn on momentarily.
4) If the auxiliary sensor input is activated the LEDs will activate momentary.
450 SERIES
PAGE 11
DIAGNOSTICS
SYSTEM PROGRAMMING
- Menu 1
OWNER'S MANUAL
ALARM STATUS / DIAGNOSTICS
If the alarm system is triggered, the system will retain in memory the cause of the
trigger. When disarming the alarm, the siren/horn will chirp 3 times to indicate
the alarm had been triggered. The system’s LED will also flash in pulses to
indicate which input triggered the alarm.
*LED status will be cleared when the ignition is turned ON. For proper memory
clearing, insure to connect the alarm ignition input to the ignition on the vehicle.
SIREN CHIRPS
LED FLASHES
DIAGNOSTICS / STATUS
3
3
3
0
0
0
0
2
3
4
OFF
ON SOLID
SINGLE FLASHES
RAPID FLASHES
SHOCK SENSOR TRIGGER
DOOR / HOOD TRIGGER
IGNITION TRIGGER
SYSTEM DISARMED
SYSTEM IN VALET / SERVICE MODE
SYSTEM ARMED
PASSIVE ARM COUNTDOWN
ALARM STATUS / DIAGNOSTICS
If an output from the alarm is shorted the siren will chirp 4 times and the park
lights will flash 4 times when the system is armed or disarmed. The LED will flash
a diagnostic code that represents the circuit that is at fault. (See Chart Below).
Turning the ignition to the on then off position will reset the diagnostic code.
LED FLASHES
OUTPUT DIAGNOSTICS
2
3
4
5
6
7
8
LOCK OUTPUT OVERLOAD
UNLOCK OUTPUT OVERLOAD
TRUNK OUTPUT OVERLOAD
STARTER DISABLE OVERLOAD
NOT USED
AUX 5 OUTPUT OVERLOAD
2ND UNLOCK OUTPUT OVERLOAD
450 SERIES
PAGE12
OWNER'S MANUAL
technical support: [email protected]
additional product information: www.ultrastarters.com
IMPORTANT NOTES
LOCK, UNLOCK, DRIVER'S DOOR PRIORITY UNLOCK, TRUNK RELEASE AND THE
AUXILIARY OUTPUTS ARE OPTIONAL OUTPUTS. ENABLING THESE FEATURES
REQUIRES CUSTOM INSTALLATION & PROGRAMMING. THESE FEATURES MAY NOT BE
COMPATIBLE WITH SOME VEHICLES.
FOR SAFETY REASONS THE TRUNK RELEASE OUTPUT WILL NOT ACTIVATE WHEN THE
IGNITION IS IN THE ON POSITION.
NOTE: PADLOC AND 2ND CAR OPERATION ARE FEATURES THAT REQUIRE SPECIAL
PROGRAMMING.
SOME FEATURES MAY NOT BE AVAILABLE FOR ALL APPLICATIONS. CONTACT YOUR
DEALER FOR MORE INFORMATION.

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement