User manual | Ultra Start 72 Series Automobile Alarm User Manual

Ultra Start 72 Series Automobile Alarm User Manual
REV.2008.06.18
72 SERIES
Advanced Remote Starters &
Vehicle Security Systems
TM
OWNER’S MANUAL
www.ultrastarters.com
FOR USE ON AUTOMATIC TRANSMISSION
VEHICLES ONLY
FCC ID NOTICE
This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions:
1. This device may not cause harmful interference, and
2.This device must accept any interference received, including interference that may cause undesired operation.
CAUTION: Changes or modifications not expressly approved by the part responsible for compliance void the user’s authority to operate
this devise.
72 SERIES
PAGE 2
OWNER'S MANUAL
TABLE OF CONTENTS
Important Notes.......................................................................Page 3
Quick View Operations...........................................................Pages 4-5
Remote Start Operations........................................................Pages 6-12
Remote Start
Idle Mode
Key Takeover
extended Runtime
Remote Shutdown
Turbo Timer Mode
Remote Start Optional Operations.........................................Pages 6-11
Lock Doors
Auxiliary Outputs
Car Finder Mode
Unlock Doors
Panic Mode
Trunk Release
Silent Lock/Unlock
Emergency Override Mode.....................................................Page 12
Activate Override Mode
Deactivate Override Mode
Timer Mode/ Cold Start...........................................................Page 13
Transmitter Programming.......................................................Page 14
LED 2way Operations..............................................................Page 15-16
Lock 2way
Panic Mode
Unlock 2way
Cold Start
Trunk Release 2way
Low Battery Indication
Trouble Shooting.....................................................................Page 17
Diagnostics..............................................................................Page 18
Warranty...................................................................................Page 19
Other.........................................................................................Page 20
PAGE 3
IMPORTANT NOTES
72 SERIES
OWNER'S MANUAL
ATTENTION
Please take a moment to review the safety precautions before
operating your system.
1) For safety reasons, the owner/user of this system MUST INSTALL
a CARBON MONOXIDE DETECTOR in the living area near to where
the vehicle is being stored or parked.
2) It is the sole responsibility of the owner/user to keep the remote
transmitters away from the reach of children and handle with care
so that the system does not unintentionally start.
3) When the vehicle is parked in an enclosed/partially enclosed area
(ex: garage, car port...), being serviced (ex: oil change) or the
vehicle is loaned to an operator not familiar with a remote starter,
the system MUST BE placed Service Mode.
4) MANUAL TRANSMISSION STARTERS Never install a automatic
remote start module into a manual transmission vehicle. Doing so
could result in EXTENSIVE DAMAGE TO YOUR VEHICLE,
PROPERTY DAMAGE AND POSSIBLY CAUSE SERIOUS INJURIES
OR EVEN DEATH. IF THIS SYSTEM WAS INSTALLED IN A MANUAL
TRANSMISSION VEHICLE, RETURN TO YOUR DEALER AND HAVE
IT DISABLED UNTIL THE CORRECT MODEL CAN BE INSTALLED.
5)NEVER REMOTE START THE SYSTEM IN AN ENCLOSED/
PARTIALLY ENCLOSED AREA!
72 SERIES
PAGE 4
OWNER'S MANUAL
BUTTON
LOCK
UNLOCK/
TRUNK
QUICK VIEW CHART
BUTTON PRESS
HONKS /
FLASH
SYSTEM FUNCTION
1 SECOND
1
LOCK DOORS
3 SECONDS
1
ACTIVATE PANIC MODE
PRESS THEN
RELEASE THEN
PRESS & HOLD
1
ACTIVATE CONSTANT LOCK OUTPUT
1 SECOND
2
UNLOCK DOORS
1 SECOND
WHILE ALARM IS
TRIGGERED
NONE
TURNS OFF PANIC BUT DOOR STAY
LOCKED
5 SECONDS
2
AUXILIARY #2 OUTPUT
PRESS & RELEASE
1
ACTIVATES REMOTE STARTER
PRESS & HOLD
2
TURN OFF REMOTE STARTER
PRESS AND HOLD
HOLD FOR 3 SEC
2
ON
AUXILIARY #1 OUTPUT (DEFAULT)
CAR FINDER (PROGRAMMABLE)
START
AUX
+
PRESS TOGETHER
THEN RELEASE
PRESS TOGETHER
THEN RELEASE
1
2
ACTIVATES SILENT LOCK WITHOUT
HONKS
ACTIVATES SILENT UNLOCK WITHOUT
HONKS
72 SERIES
PAGE 5
OWNER'S MANUAL
QUICK VIEW CHART
BUTTON
+
2ND CAR
OPERATION
+
2ND CAR
OPERATION
BUTTON PRESS
HONKS /
FLASH
SYSTEM FUNCTION
1 SEC
1
2ND CAR LOCK
3 SEC
1
2ND CAR ACTIVATE PANIC*
PRESS THEN
RELEASE THEN
PRESS & HOLD
1
2ND CAR ACTIVATE CONSTANT LOCK
OUTPUT
1 SEC
2
2ND CAR UNLOCK
1 SEC
WHILE PANIC IS
TRIGGERED
NONE
2ND CAR TURNS OFF HORN BUT THE
DOORS STAY LOCKED
2ND CAR OPERATION IS NOT AVAILABLE ON 2WAY MODELS
SERVICE MODE / EMERGENCY OVERRIDE MODE
TO AVOID SERIOUS INJURY, this remote start system must be set into Service Mode
before any under hood servicing is started. Service Mode will prevent the vehicle from
starting while the vehicle is being serviced. It is the sole responsibility of the vehicle’s
owner to place the system into Service Mode. The manufacture accepts no responsibility
for accidental starting of the vehicle while the vehicle is being serviced.
ACTIVATING / DEACTIVATING VALET MODE / EMERGENCY OVERRIDE
Turn the Ignition Key ON
(Leaving the key ON)
Press and hold the Valet switch for 8 to 15 seconds
(Time depends on "Valet Settings" Program Option)
5 HONKS = OFF
REMOTE START DEACTIVATED
2 HONKS = ON
REMOTE START ACTIVATED
72 SERIES
OWNER'S MANUAL
PAGE 6
SYSTEM OPERATIONS
PRESS & RELEASE
REMOTE STARTER ACTIVATION
1. Press and release the START button on the remote transmitter one time.*
*Press twice if the system is programmed for Safety Start.
2. The park lights will flash and the horn (optional) will Honk once as confirmation.
3. The vehicle will remote start and the park lights will turn on and remain on while the vehicle is
running under remote start**.
- If the remote start fails to start see the diagnostics chart at the back of the manual.
**DEFAULT RUNTIME OF THE SYSTEM IS 15 MINUTES.
TURN KEY ON
KEY TAKEOVER
Once the vehicle is remote started and you wish to enter the vehicle to drive away you must
preform the following steps.
1. Enter the vehicle then insert the key into the ignition switch.
2. Turn the key forward to the ON or RUN* position. (This is usually 2-3 key positions)
*Do not turn the key to the start position.
3. Step on the brake and the remote starter will turn off however the vehicle will continue to run
because the key is on. If the key is not in the on position when the brake is pressed the remote
starter and the vehicle will both shut off.**
** If the vehicle shuts down simply restart the engine with the key.
DO NOT TURN THE KEY TO THE START POSITION WHILE THE ENGINE IS RUNNING.
PAGE 7
SYSTEM OPERATIONS
72 SERIES
OWNER'S MANUAL
PRESS & HOLD
REMOTE STARTER SHUT DOWN
1. While the vehicle is running with the remote starter press and hold the START button for three
seconds.
2. The park lights will flash and the horn (optional) will honk 2 times to confirm shutdown.
- Pressing the brake pedal or opening the hood will also shut down the remote starter.
THE VEHICLE WILL SHUT OFF WHEN THE RUNTIME EXPIRES (DEFAULT 15MIN)
PRESS & RELEASE
ENGINE IDLE MODE
This feature allows the user to safely leave the vehicle running without leaving the keys in the
ignition.
1. While the vehicle is running with the key press and release the START button then remove the
key from the ignition. The vehicle will run for 15 minute while you are away.
PRESS & RELEASE
EXTENDED RUNTIME
1. While the vehicle is running with the remote starter, press and release the START button.
2. The park lights will flash and the horn (optional) will honk one time as confirmation.
The system will reset the run time (See Example Below)**.
**Not available with 4 minute run time.
Example- If the vehicle has been remote started for 10 minutes and you press and release the
start button the system will run for a addition 15 minutes totalling 25 minutes of runtime.
PRESS & RELEASE
TURBO TIMER MODE
While the vehicle is running with the key, press and release the # button. The park lights will turn
on and the horn (optional) will Honk twice ( If connected the doors will unlock). When the ignition
key is turned to the “OFF” position the vehicle will remain running for 2 minutes.
72 SERIES
OWNER'S MANUAL
PAGE 8
SYSTEM OPERATIONS
PRESS & RELEASE
LOCK DOORS
1.
2.
3.
4.
Press and release the Lock Button on the remote transmitter.
The park lights will flash and the horn (optional) will Honk one time.
The doors will lock.
The LED will start flashing within five seconds.
NOTES:
- If the panic mode is activated pressing the lock button on the remote will stop the horn
from sounding.
- The horn can be programmed to honk with Car Finder and Panic Mode only.
- If the system is in Service Mode the doors will lock/ unlock but the horn will not honk.
- The LEDs will be on solid if the system is in Service Mode.
See Valet / Service Mode in this manual for further information
** Optional Feature may require additional parts and labor.
NEW- The LEDs can now be programmed not to flash when the doors are locked by
the remote transmitter.
PRESS & HOLD
TRUNK RELEASE/ AUX 2 OUTPUT
1.
2.
3.
4.
5.
Press then HOLD the Unlock Button on the remote transmitter.
The park lights will flash and the horn (optional) will honk two times.
The doors will unlock and the dome lights will activate. (optional)
The LEDs will stop flashing.
Continue to HOLD the Unlock Button until the trunk release activates.
NOTES:
- For safety, the trunk release will not active when ignition key is ON.
** Optional Feature may require additional parts and labor.
72 SERIES
PAGE 9
OWNER'S MANUAL
SYSTEM OPERATIONS
PRESS & RELEASE
UNLOCK DOORS
1.
2.
3.
4.
Press then release the Unlock Button on the remote transmitter.
The park lights will flash and the horn (optional) will honk two times.
The doors will unlock and the dome lights will activate. (optional)
The LEDs will stop flashing.
NOTES:
- If the panic mode is activated the first press of the unlock button will turn off the horn off and
the second press will unlock the doors.
- The horn can be programmed to honk with Car Finder and Panic Mode only.
- If the system is in valet mode the doors will lock/ unlock but the horn will not honk.
- The LEDs will be on solid if the system is in valet mode.
See Valet / Service Mode in this manual for further information
** Optional Feature may require additional parts and labor.
PRESS TWICE
DRIVER'S DOOR PRIORITY UNLOCK
1. Press then release the Unlock Button on the remote transmitter.
2. The park lights will flash and the horn (optional) will honk two times.*
3. The driver's doors will unlock and the dome lights will activate. (optional)
4. The LEDs will stop flashing.
5. Press the Unlock Button a second time within 3 seconds and all of the other doors
will unlock.*
*This is an optional feature that may not be available on all vehicles.
** Optional Feature may require additional parts and labor.
72 SERIES
PAGE 10
OWNER'S MANUAL
SYSTEM OPERATIONS
PRESS HOLD
ACTIVATE PANIC MODE
1.
2.
3.
4.
5.
Press and HOLD the Lock Button for three seconds.
The doors will lock.
The park lights will begin to flash and the horn will honk ON and OFF.
To turn off panic, press Lock or Unlock Buttons on remote.
If no button is pressed, Panic will stay active for 1 minute then turn off.
Panic Mode is a personal protection feature that allows you to activate your alarm from the
remote transmitter. This feature can be used to draw attention to your vehicle if you feel
threatened.
+
PRESS TOGETHER
SILENT LOCK / SILENT UNLOCK
1. Press then release the Lock & Unlock buttons together.
2. If the system is UNLOCKED, it will Lock the doors with no horn honks. The park
lights will flash 1 time.
3. If the system is LOCKED, it will Unlock the doors with no horn honks. The park
lights will flash 2 times.
PRESS & HOLD for 3 sec
CAR FINDER MODE
1. PRESS & HOLD The # Button on the remote transmitter for 5 seconds.
- The horn will honk 5 times and the park lights will flash 5 times.
This feature helps in locating your vehicle in a crowded parking lot. It allows you hear and see
your vehicle from a distance.
*The horn output must be connected and this feature must be programmed on..
72 SERIES
PAGE 11
SYSTEM OPERATIONS
OWNER'S MANUAL
HOLD THE # BUTTON
AUXILIARY OUTPUT 1
The Aux output can be programmed for a variety of custom applications. (SEE
DEALER FOR DETAILS)
1. To activate Auxiliary Channel 1 output press and hold the # Button for 3 seconds.
2. The system will unlock the doors then the AUX 1 output will activate.
3. Release the buttons for a momentary output or continue holding for up to a 5
second output.
This feature can be used to open the trunk, open or close power windows or control
sliding doors on minivans.
HOLD UNLOCK
AUXILIARY OUTPUT 2/ TRUNK RELEASE
The Aux output can be programmed for a variety of custom applications. (SEE
DEALER FOR DETAILS)
1. To activate Auxiliary Channel 2 output press and hold the Unlock Buttons for 3
seconds.
2. The system will unlock the doors then the AUX 2 output will activate.
3. Release the buttons for a momentary output or continue holding for up to a 5
second output.
This feature can be used to open the trunk, open or close power windows or control
sliding doors on minivans.
Having the Auxiliary output options connected is subject to addition labour and
parts. Some features and functions are not available on all vehicles.
72 SERIES
OWNER'S MANUAL
PAGE 12
OVERRIDE MODE
EMERGENCY OVERRIDE MODE
This feature is to be used if the remote transmitter is lost or is not communicating with
the system. This will disable the optional starter disable if installed. Follow the steps
below to deactivate your system.
ACTIVATING EMERGENCY OVERRIDE MODE
Turn the Ignition Key ON
(Leave in the ON position)
Press and hold the Valet switch for 8 to 15 seconds
(Time depends on "Valet Settings" Program Option)
The horn will honk 5 times as confirmation that the system is
now in Emergency Override Mode.
DEACTIVATING EMERGENCY OVERRIDE MODE
Turn the Ignition Key ON
(Leave in the ON position)
Press and hold the Valet switch for 8 to 15 seconds
(Time depends on "Valet Settings" Program Option)
The horn will honk 2 times as confirmation that the system is
has exited Emergency Override Mode.
72 SERIES
PAGE 13
OWNER'S MANUAL
COLD START MODE
SETTING COLD START MODE
Code Start Mode will start the vehicle at a user selectable start interval. The vehicle
can be set to start once every 2, 3 or 4 hours, for a maximum of 12 starts. The
vehicle will start at the selected start interval and run for the programmed runtime*.
EXAMPLE: If the 4 hour start cycle was selected, the vehicle will start once every 4
hours and run for the programmed runtime*.
Method 1- Press and release the
button, then press and hold the
seconds or until park lights turn on. Use on 2way Models.
Method 2 - Press the
park lights will turn on.
and
button for 6
buttons at the same time for 3 seconds or until the
While the park lights are on the start cycle may be selected. See below:
2 hours
3 hours
4 hours
Press and release the
Press and release the
Press and release the
button
button
button
2 Park light flashes
3 Park light flashes
4 Park light flashes
NOTE: Timer Mode must be set each time the user wishes to use this feature.
To Cancel Cold Start Mode
Timer Mode will automatically turn off after 24 hrs or you may use one of the
following methods to manually disable Timer Mode. Cancellation will be confirmed
with 2 park light flashes and 2 horn Honks.
Method 1- Press and release the
button, then press and hold the
button for 6
seconds.
Method 2- Press the
and
buttons at the same time for 3 seconds.
NOTE: Pressing the brake pedal or turning the ignition to the ON position will cancel
Cold Start Mode.
72 SERIES
PAGE 14
OWNER'S MANUAL
REMOTE PROGRAMMING
The system can lean up to 4 different remote’s. Each remote to be used MUST be
programmed together during the same sequence. For security, when a new remote is
programmed all previous remote’s are deleted. Please see remote operation chart for
information on using Second Car / Pad Lock Operations.
ENTERING REMOTE PROGRAM MODE
1-
Cycle the Ignition Key - ON/OFF ON/OFF ON (Leaving the key ON)
2-
HOLD program switch, the HORN will Honk ONCE and the park lights will turn on.
(If the HORN does not Honk repeat step 1)
CONTINUE TO HOLD until HORN Honks 5 times
3-
1 Honk confirms program mode entered followed by 5 Honks confirming
transmitter program mode
PROGRAMMING REMOTE’S
4-
Press & Release LOCK button on 1st Remote to be Programmed for Normal
Operation If remote(s) are to be programmed for "PADLOCK" skip and
goto step 6
5-
HORN will Honk 1 time to confirm remote has been
programmed (If the HORN does not Honk press button again)
REPEAT STEP 4 IF A SECOND REMOTE IS TO BE PROGRAMMED FOR NORMAL OPERATION
6-
Press & Release BUTTON 4 on Remote to be Programmed
for 2ND CAR OR PAD LOCK
7-
HORN will Honk 1 time to confirm remote has been
programmed (If the HORN does not Honk press button again)
REPEAT STEP 6 IF A SECOND REMOTE IS TO BE PROGRAMMED FOR 2ND CAR / PADLOCK OPERATION
8-
Turn ignition key OFF to exit remote program mode when
all required remote’s have been programmed.
72 SERIES
PAGE 15
LED 2 WAY OPERATIONS
OWNER'S MANUAL
LED 2 WAY SYSTEMS
LED 2way utilizes a bright blue light (LED) below the button that
illuminates the button pad shortly after the button is pressed.
The transmitter will also “beep” as an audible confirmation of the
function.
LOCK BUTTON
When the lock button is pressed the light behind the button will flash once
and the remote will beep once as confirmation that the function has been
completed. If the system is not in range the remote will beep 3 times.
LOCK
UNLOCK BUTTON
UNLOCK
When the unlock button is pressed the light behind the button will flash twice
and the remote will beep twice as confirmation that the function has been
completed. If the system is not in range the remote will beep 3 times.
START BUTTON
START
When the start button is pressed the light behind the start button will begin to
flash, when the vehicle start the remote will flash both the start button and the
status or the system. (locked or unlocked) If the system is not in range the
remote will beep 3 times.
STATUS UPDATE BUTTON
When the STATUS button is pressed the button will flash once the remote will
beep once. Soon after the remote will beep and flash the appropriate button
to indicate the status of the system. If the system is not in range the remote
STATUS will beep 3 times.
72 SERIES
PAGE 16
OWNER'S MANUAL
LED 2 WAY
LED 2 WAY SYSTEMS
HOLD
LOCK
HOLD
PANIC MODE
When the lock button is held for 5 seconds the system will enter Panic Mode.
The LEDs under the buttons will flash in a pattern and the remote will beep to
indicate Panic Mode is active. If the system is not in range the remote will
beep 3 times.
TRUNK RELEASE
When the unlock button is held the light behind the button will flash twice and
the remote will beep twice after 3 seconds the remote with beep again as
confirmation that the function has been completed. If the system is not in
UNLOCK range the remote will beep 3 times.
COLD START MODE (See page 13 for more details)
1- Press and release the # button then within 3 seconds hold the start button for 8 seconds.
2- All 4 LEDs on the remote will illuminate to indicate that the start cycle selection. Within 3
seconds select the start cycle
a. Press Unlock for 2hr timer. LEDs will flash twice as confirmation.
b. Press Start for 3hr timer. LEDs will flash three times as confirmation.
c. Press # for 4hr timer. LEDs will flash four times as confirmation.
PRESS AND
RELEASE
THEN
PRESS AND
HOLD
HOLD 8 SEC.
LOW BATTERY WARNING
When the battery voltage is low all of the LEDs behind the buttons will
LOW
BATTERY activate at the same time and the remote will beeps once immediately when
a button is pressed. Range and features such as Panic Mode and Trunk
Release may not function when the batteries are low.
72 SERIES
PAGE 17
TROUBLE SHOOTING
SYMPTOM
Vehicle is not remote
starting?
OWNER'S MANUAL
CAUSE/SOLUTION
- Count the park light flashes then see the diagnostics page.
- Check battery voltage in the remote.
- Make sure you are with-in operating range.
- Check if the vehicle anti-theft is activating.
- Reprogram the remote’s using Transmitter Program Mode.
- Check if the vehicle anti-theft is activating.
Vehicle starts then shuts - Is the starter motor staying on to log? If so,
reprogram the tach and try again.
off by itself
- See dealer if problem is not resolved.
The system does not
respond to the remote
transmitter
- Try your second remote.
- Check the batteries in the remote.
Reprogram the remote’s using Transmitter Program Mode.
- Make sure you are with-in operating range.
Doors do not lock
Or unlock
- Was this optional feature installed?
- Have your installer check the door lock connector.
- Have bypass or keyless module reprogrammed.
Horn does not honk
- Was this optional feature installed?
- Try panic mode to see if horn activates. If not,
have the systems horn output checked.
Lights on the antenna
are flashing
- When the doors are locked by the remote the LEDs will flash until the
unlock button is pressed.
- If you do not want the LEDs to flash have your installer program the
LED flashes off.
PLEASE NOTE
We recommend that you contact your dealer if you encounter an with your system. If your dealer
is not available, see http://ultrastarters.com/dealer_locator.html to locate an Authorized
Dealer in your area. For more advanced trouble shooting tips, programming videos, programming
PDF’s and FAQ’s please visit www.ultrastarters.com/support.html
72 SERIES
PAGE 18
OWNER'S MANUAL
DIAGNOSTICS
DIAGNOSTICS
Diagnostic Mode is a tool that can help trouble shoot a start fault. If the remote
starter fails to start i.e.: the hood is open the park likes will flash a diagnostic code.
i.e.: 5 flashes = start attempt with hood open. If the vehicle does not remote start,
count the park light flashes then compare it to the chart below.
PARK LIGHTS
LED FLASHES
DIAGNOSTICS / STATUS
3 SLOW FLASHES
LED’s ON SOLID
SYSTEM IS IN SERVICE MODE.
5 SLOW FLASHES
SERIES OF 5 FLASHES
START ATTEMPT WHILE IGNITION IS ON
5 FLASHES
SERIES OF 5 FLASHES
START ATTEMPT WITH HOOD SWITCH OPEN
6 FLASHES
SERIES OF 6 FLASHES
START ATTEMPT WITH BRAKE APPLIED
7 FLASHES
SERIES OF 7 FLASHES
SYSTEM IS IN TACH LOCK OUT (SEE DEALER)
8 FLASHES
SERIES OF 8 FLASHES
THREE START ATTEMPTS WITH NO START
The start fault must be corrected in order for the system to operate correctly. See
your dealer for additional trouble shooting or visit www.ultrastarters.com and visit the
support page.
PLEASE NOTE
We recommend that you contact your dealer if you encounter an with your system. If your dealer
is not available, see http://ultrastarters.com/dealer_locator.html to locate an Authorized
Dealer in your area. For more advanced trouble shooting tips, programming videos, programming
PDF’s and FAQ’s please visit www.ultrastarters.com/support.html
PAGE 19
PRODUCT WARRANTY
72 SERIES
OWNER'S MANUAL
WARRANTY
Applicated Security Technologies, Inc. ("AST") promises to the original purchaser to repair or replace with
a comparable reconditioned model any AST control module ("module") excluding without limitation the
any other accessories, including but not limited to the antenna, remote, siren and wiring harness, proves
to be defective in workmanship or material under reasonable use during the lifetime of the vehicle it was
originally installed, provided the following conditions have been met: the module was professionally
installed and serviced by an authorized AST dealer; the unit will be professionally reinstalled in the
vehicle in which it was originally installed by an authorized AST dealer; the warranty information card was
sent to AST within 10 days of the original installation date. Any warranty returns include a warranty return
authorization number issued by AST, original bill or sale and be pre-paid shipped directly to AST. After an
initial period of 2 years from the date of installation, AST reserves the right, at its sole discretion, to
charge a warranty processing fee of $30.00 USD. AST does not cover the cost for return freight on
warranty items, this cost is the sole responsibility of the purchaser.
All components included with the original packaged unit other than the module, including but not limited to
the siren, antenna and the remote transmitters, carry a one-year warranty from the date of purchase of
the same. Any warranty returns on components must include a warranty return authorization number
issued by AST, original bill or sale and be pre-paid shipped directly to AST. This warranty is nontransferable and is automatically void if: the original purchaser has not completed the warranty card and
mailed it within ten (10) days of the date of purchase to the address listed on the card; the unit's date
code or serial number is defaced, missing or altered; the unit has been modified or used in a manner
contrary to its intended purpose; the unit has been damaged by accident, unreasonable use, neglect,
improper service, installation or other causes not arising out of defects in materials or construction. The
warranty does not cover damage to the unit caused by installation or removal of the unit. AST, at its sole
discretion, will determine what constitutes excessive damage and may refuse the return of any unit with
excessive damage, including, but not limited to, overloading, moisture and physical damage.
To the maximum extent allowed by law, any and all warranties are excluded by the manufacturer and
each entity participating in the stream of commerce therewith. This exclusion includes but is not limited to,
the exclusion of any and all warranty of merchantability and/or any and all warranty of fitness for a
particular purpose and/or any and all warranty of non-infringement or patents, in the United States of
America and/or abroad. Neither the manufacturer or any entities connected therewith shall be responsible
or liable for any damages whatsoever, including but not limited to, any consequential damages, incidental
damages, damages for loss of time, loss of earnings, commercial loss, loss of economic opportunity and
the like. Notwithstanding the above, manufacturer does offer a limited warranty to replace or repair the
control module as describe above.
Some states do not allow limitations on how long an implied warranty will last or the exclusion or limitation
on how long an implied warranty will last or the exclusion or limitation of incidental or consequential
damages. This warranty gives you specific legal rights, and you may also have other rights, which vary
State to State.
72 SERIES
PAGE 20
OWNER'S MANUAL
Technical Support: support@ultrastarters.com
Additional Product Information: www.ultrastarters.com
IMPORTANT NOTES
LOCK, UNLOCK, DRIVER'S DOOR PRIORITY UNLOCK, TRUNK RELEASE AND THE
AUXILIARY OUTPUTS ARE OPTIONAL OUTPUTS. ENABLING THESE FEATURES
REQUIRES CUSTOM INSTALLATION & PROGRAMMING. THESE FEATURES MAY NOT BE
COMPATIBLE WITH SOME VEHICLES.
FOR SAFETY REASONS THE TRUNK RELEASE OUTPUT WILL NOT ACTIVATE WHEN THE
IGNITION IS IN THE ON POSITION.
NOTE: PADLOC AND 2ND CAR OPERATION ARE FEATURES THAT REQUIRE SPECIAL
PROGRAMMING.
SOME FEATURES MAY NOT BE AVAILABLE FOR ALL APPLICATIONS. CONTACT YOUR
DEALER FOR MORE INFORMATION.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising