Ultra Start 80 series 1280, 2280, 3280, 3285, 4280, 4285 remote starter Owner's guide

REV.2007.11.13A

Car Finder and Auxiliary 1 are not available on 2way models.

PRESS & RELEASE

ARM SYSTEM / LOCK DOORS

Timer Mode will start the vehicle at a user selectable start interval. The vehicle can be set to start once every 2, 3 or 4 hours, for a maximum of 12 starts. The vehicle will start at the selected start interval and run for the programmed runtime*. EXAMPLE: If the 4 hour start cycle was selected, the vehicle will start once every 4 hours and run for the programmed runtime*.

Press and Hold for 3 seconds or until the park lights turn on.

While the park lights are on the start cycle may be selected. See below:

2hour Press and release the button 2 Park light flashes

3hour Press and release the button 3 Park light flashes

4hour Press and release the button 4 Park light flashes

NOTE: Timer Mode must be set each time the user wishes to use this feature.

To Cancel Timer Mode

Timer Mode will automatically turn off after 24 hrs or you may use one of the following methods to manually disable Timer Mode. Cancellation will be confirmed with 2 park light flashes and 2 horn chirps.

Press and Hold for 3 seconds or until the park lights flash twice.

NOTE: Pressing the brake pedal or turning the ignition to the ON position will cancel Timer Mode.

IMPORTANT: Never remote start or set the Timer Mode if the vehicle is parked in a Garage or Attached Carport!

SHOCK SENSOR ADJUSTMENTS

1 - ENTER SHOCK SENSOR ADJUSTMENT MODE

+

Press & HOLD Lock + Unlock buttons at the same time

3 CHIRPS

Continue to hold for 3-5 seconds Until Siren Chirps 3 times

(Note: System will Arm or Disarm via silent arming prior to entering adjustment mode)

2 - ADJUSTING SENSOR

Each time the lock button is pressed and released the sensitivity will be

INCREASED by 1 level.

This is confirmed by a series of park light flashes & Siren Chirps

1 Flash / Chirp is the least sensitive setting

10 Flashes / Chirps is the most sensitive setting

Each time the unlock button is pressed and released the sensitivity will be

DECREASED by 1 level.

This is confirmed by a series of park light flashes & Siren Chirps

1 Flash / Chirp is the least sensitive setting

10 Flashes / Chirps is the most sensitive setting

3 - EXITING SENSOR ADJUSTMENT MODE

+

Press & HOLD Lock + Unlock buttons at the same time

(NOTE: Shock Sensor Adjustment Mode has an auto time out of

8 seconds)

80 SERIES

OWNER'S MANUAL

PAGE 18

LED 2way utilizes a bright blue light (LED) below the button that illuminates the button pad shortly after the button is pressed. The transmitter will also “beep” as an audible confirmation of the function.

LOCK

LOCK BUTTON

When the lock button is pressed the light behind the button will flash once and the remote will beep once as confirmation that the function has been completed. If the system is not in range the remote will beep 3 times.

UNLOCK

UNLOCK BUTTON

When the unlock button is pressed the light behind the button will flash twice and the remote will beep twice as confirmation that the function has been completed. If the system is not in range the remote will beep 3 times.

START

START BUTTON

When the start button is pressed the light behind the start button will begin to flash, when the vehicle start the remote will flash both the start button and the status or the system. (locked or unlocked) If the system is not in range the remote will beep 3 times.

STATUS

STATUS UPDATE BUTTON

When the STATUS button is pressed the button will flash once the remote will beep once. Soon after the remote will beep and flash the appropriate button to indicate the status of the system. If the system is not in range the remote will beep 3 times.

PAGE 19

80 SERIES

OWNER'S MANUAL

RUN TIMER- This icon indicates the amount of time that the remote starter will run. The timer counts down in 2 minute increments

EXHAUST and WHEEL’S- When the remote start is activated the remote will play a tune then turn on the remote start icons such as spinning tires, exhaust, key symbol and park light flash. Press the

# button at any time to refresh the status.

LOCK ICON - This icon indicates that the doors are locked and the alarm is armed (ALARM MODELS) The status can be check at anytime by pressing the # button on the remote.

UNLOCK ICON - This icon indicates that the doors are unlocked and the alarm is disarmed. The status can be check at anytime by pressing the # button on the remote.

TRUNK ICON- This icon indicates that the Trunk Release feature has been activated. The status will update when the lock button is pressed or when manually updated by pressing the # button.

SIREN and LOCK ICONS*- These icons indicate that the alarm has been triggered by the door, hood or ignition inputs. The remote must be set for PAGER MODE for the remote to update the status automatically. (ALARM MODELS)

SIREN and HAMMER ICONS*- These icons indicate that the alarm has been triggered by the shock sensor input. The remote must be set for PAGER MODE for the remote to update the status automatically. (ALARM MODELS)

80 SERIES

OWNER'S MANUAL

PAGE 20

The ANTENNA icon indicates the signal strength between the remote and the vehicle. If the vehicle is out of operating range when a button is pressed the ANTENNA icon will disappear from the LCD.

The KEY icon is displayed on the top of the LCD when the remote starter is activated. When the runtime expires this icon will turn off.

The SIREN icon indicates that the alarm has been activated, the LCD will also display the hammer or unlock icon depending on the input that triggered the alarm. ALARM MODELS ONLY.

The TRUNK icon will be displayed on the LCD when the TRUNK RELEASE output is activated. The icon will turn off when the next function is activated or with STATUS update.

The BATTERY icon indicates the power level of the battery. Replace the battery once two of the bars have disappeared.

The TIMER icon is displayed in conjunction with the TIMER MODE/ COLD START MODE. When the icon is on the system is set to start at the preset time/temperature.

Pressing the # button at any time will update the status on the remote. Hold the # button to enter

REMOTE PROGRAM MODE.

REMOTE PROGRAMMABLE FEATURES

To turn a programmable feature on or off, press and hold the # button until the 24h icon begins to flash. Press and release the lock button until the desired icon begins to flash. Press the unlock

button to turn the feature OFF or press the star button to turn it ON. When done press # to

When the TIMER icon is on at the bottom of the LCD the vehicle is set for COLD START or TIMER

MODE. If this icon is turned on by remote the system will start at the last manually programmed cycle.

The PHONE icon at the bottom of the LCD indicates the status of the PAGER MODE. When the Icon is on the status is checked every 15 seconds. When off the status is updated by pressing #.

The small KEY icon at the bottom of the LCD indicates that a fault is preventing the remote starter from activating. Count the park light flashes then refer to the DIAGNOSTICS CHART.

?

The small HORN icon at the bottom of the LCD indicates the status of the Horn/ Siren chirp feature. If the icon is ON the system will chirp as confirmation of a function. For no chirp turn the icon OFF.

The HAMMER icon is displayed at the bottom of the LCD on ALARM MODELS as an indication of the status of the Shock Sensor. If on the Shock Sensor is active. Turn off to disable the Shock Sensor.

The Question Mark icon indicated the status of the SERVICE MODE feature. When the icon is on the system is disabled from remote starting and all alarm functions will be turned off.

PAGE 21

80 SERIES

OWNER'S MANUAL

SETTING THE TIME (LCD 2way MODELS)

To set the time on LCD 2way models, p ress and hold the and buttons until the remote transmitter chimes and the minute portion of the clock begins to flash.

To change from minutes to hours, press and release the button.

To increase the minutes or hours, press and release the button.

To decrease the minutes or hours, press and release the button.

Press and release the button to exit or the remote transmitter will exit if there is no activity for 20 seconds.

NOTE: To set the AM/ PM icon, continue changing the hour until the appropriate icon is displayed.

PAGER ICON

PAGER MODE ON

PAGER ICON

PAGER MODE

PAGER MODE OFF

2 4 6 8 10 14 16 2 4 6 8 10 14 16

To turn Pager Mode ON

Press and hold the # button until the 24H icon begins to flash.

Press and release the lock button the Pager Icon (phone) will start to flash.

Press and release the start button the Pager Icon will start to flash.

Press and release the # button to exit. The Page Icon will turn on.

To turn Pager Mode OFF

Press and hold the # button until the 24H icon begins to flash.

Press and release the lock button the Pager Icon (phone) will start to flash.

Press and release the unlock button the Pager Icon will start to flash.

Press and release the # button to exit. The Page Icon will turn off.

80 SERIES

OWNER'S MANUAL

PAGE 22

ALARM STATUS / DIAGNOSTICS

Diagnostic Mode is a tool that can help trouble shoot a start fault. If the remote starter fails to start i.e.: the hood is open the park likes will flash a diagnostic code. i.e.: 5 flashes = start attempt with hood open. If the vehicle does not remote start, count the park light flashes then compare it to the chart below.

PARK LIGHTS LED FLASHES DIAGNOSTICS / STATUS

3 SLOW FLASHES

4 SLOW FLASHES

5 SLOW FLASHES

5 FLASHES

6 FLASHES

7 FLASHES

8 FLASHES

LED’s ON SOLID

SERIES OF 8 FLASHES

SERIES OF 5 FLASHES

SERIES OF 5 FLASHES

SERIES OF 6 FLASHES

SERIES OF 7 FLASHES

SERIES OF 8 FLASHES

SYSTEM IS IN SERVICE MODE.

NOT SET IN RESERVATION MODE “M” MODELS

START ATTEMPT WHILE IGNITION IS ON

START ATTEMPT WITH HOOD SWITCH OPEN

START ATTEMPT WITH BRAKE APPLIED

SYSTEM IS IN TACH LOCK OUT (SEE DEALER)

THREE START ATTEMPTS WITH NO START

The start fault must be corrected in order for the system to operate correctly. See your dealer for additional trouble shooting or visit www.ultrastarters.com

and visit the support page..

TROUBLE SHOOTING

The LED's do not turn on when Tach Learning?

1) The Tach wire input may be connected to the wrong wire. Check the Tach location and connection then "reset and relearn".

2) The system may be in Tachless Mode. On TL models the Tach wire connection is optional and the LED's do not turn on during the 35 second learn procedure.

When I unlock the doors the windows roll down or the Trunk Pops?

This issue is caused by the length of the unlock pulse. To correct this issue program the system for short door lock pulses. (125ms)

The alarm activates 30-45 minutes after setting it?

To prevent the vehicles battery from going dead the computer will "hibernate" like your home computer might. In some vehicles this causes the door pin input to change state. The alarm detects the change of state and activates. A relay must be installed to isolated the door pin circuit from the alarm.

The starter motor stays engaged to long when remote started?

Reset then relearn the Tach with the transmission in reverse. If the vehicle is tach learned when the idle is high the starter motor may "drag". Check your ground connection if issues persist.

PAGE 23

80 SERIES

OWNER'S MANUAL

WARRANTY

Applicated Security Technologies, Inc. ("AST") promises to the original purchaser to repair or replace with a comparable reconditioned model any AST control module ("module") excluding without limitation the any other accessories, including but not limited to the antenna, remote, siren and wiring harness, proves to be defective in workmanship or material under reasonable use during the lifetime of the vehicle it was originally installed, provided the following conditions have been met: the module was professionally installed and serviced by an authorized AST dealer; the unit will be professionally reinstalled in the vehicle in which it was originally installed by an authorized AST dealer; the warranty information card was sent to AST within 10 days of the original installation date. Any warranty returns include a warranty return authorization number issued by AST, original bill or sale and be pre-paid shipped directly to AST. After an initial period of 2 years from the date of installation, AST reserves the right, at its sole discretion, to charge a warranty processing fee of $30.00 USD. AST does not cover the cost for return freight on warranty items, this cost is the sole responsibility of the purchaser.

All components included with the original packaged unit other than the module, including but not limited to the siren, antenna and the remote transmitters, carry a one-year warranty from the date of purchase of the same. Any warranty returns on components must include a warranty return authorization number issued by AST, original bill or sale and be pre-paid shipped directly to AST. This warranty is nontransferable and is automatically void if: the original purchaser has not completed the warranty card and mailed it within ten (10) days of the date of purchase to the address listed on the card; the unit's date code or serial number is defaced, missing or altered; the unit has been modified or used in a manner contrary to its intended purpose; the unit has been damaged by accident, unreasonable use, neglect, improper service, installation or other causes not arising out of defects in materials or construction. The warranty does not cover damage to the unit caused by installation or removal of the unit. AST, at its sole discretion, will determine what constitutes excessive damage and may refuse the return of any unit with excessive damage, including, but not limited to, overloading, moisture and physical damage.

To the maximum extent allowed by law, any and all warranties are excluded by the manufacturer and each entity participating in the stream of commerce therewith. This exclusion includes but is not limited to, the exclusion of any and all warranty of merchantability and/or any and all warranty of fitness for a particular purpose and/or any and all warranty of non-infringement or patents, in the United States of

America and/or abroad. Neither the manufacturer or any entities connected therewith shall be responsible or liable for any damages whatsoever, including but not limited to, any consequential damages, incidental damages, damages for loss of time, loss of earnings, commercial loss, loss of economic opportunity and the like. Notwithstanding the above, manufacturer does offer a limited warranty to replace or repair the control module as describe above.

Some states do not allow limitations on how long an implied warranty will last or the exclusion or limitation on how long an implied warranty will last or the exclusion or limitation of incidental or consequential damages. This warranty gives you specific legal rights, and you may also have other rights, which vary

State to State.

80 SERIES

OWNER'S MANUAL

PAGE 24

Technical Support: [email protected]

Additional Product Information: www.ultrastarters.com

IMPORTANT NOTES

LOCK, UNLOCK, DRIVER'S DOOR PRIORITY UNLOCK, TRUNK RELEASE AND THE

AUXILIARY OUTPUTS ARE OPTIONAL OUTPUTS. ENABLING THESE FEATURES

REQUIRES CUSTOM INSTALLATION & PROGRAMMING. THESE FEATURES MAY NOT BE

COMPATIBLE WITH SOME VEHICLES.

FOR SAFETY REASONS THE TRUNK RELEASE OUTPUT WILL NOT ACTIVATE WHEN THE

IGNITION IS IN THE ON POSITION.

NOTE: PADLOC AND 2ND CAR OPERATION ARE FEATURES THAT REQUIRE SPECIAL

PROGRAMMING.

SOME FEATURES MAY NOT BE AVAILABLE FOR ALL APPLICATIONS. CONTACT YOUR

DEALER FOR MORE INFORMATION.