TRIPLE OUTPUT LCD SUPPLY WITH LINEAR REGULATOR AND VCOM BUFFER TPS65100, TPS65105 FEATURES

TRIPLE OUTPUT LCD SUPPLY WITH LINEAR REGULATOR AND VCOM BUFFER TPS65100, TPS65105 FEATURES
TPS65100, TPS65101
TPS65105
www.ti.com
SLVS496C – SEPTEMBER 2003 – REVISED APRIL 2006
TRIPLE OUTPUT LCD SUPPLY WITH LINEAR REGULATOR AND VCOM BUFFER
FEATURES
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
DESCRIPTION
2.7-V to 5.8-V Input Voltage Range
1.6-MHz Fixed Switching Frequency
3 Independent Adjustable Outputs
Main Output of up to 15 V With < 1% Output
Voltage Accuracy
Virtual Sychronous Converter Technology
Negative Regulated Charge Pump Driver VO2
Positive Charge Pump Converter VO3
Integrated VCOM Buffer
Auxiliary 3.3-V Linear Regulator Controller
Internal Soft Start
Internal Power-On Sequencing
Fault Detection of all Outputs (TPS65100/05)
No Fault Detection (TPS65101)
Thermal Shutdown
Available in TSSOP-24 and QFN-24
PowerPAD™ Packages
The main output, VO1, is a 1.6-MHz, fixed-frequency
PWM boost converter providing the source drive
voltage for the LCD display. The device is available
in two versions with different internal switch current
limits to allow the use of a smaller external inductor
when lower output power is required. The
TPS65100/01 has a typical switch current limit of 2.3
A, and the TPS65105 has a typical switch current
limit of 1.37 A. A fully integrated adjustable charge
pump doubler/tripler provides the positive LCD gate
drive voltage. An externally adjustable negative
charge pump provides the negative gate drive
voltage. Due to the high 1.6-MHz switching
frequency of the charge pumps, inexpensive and
small 220-nF capacitors can be used.
The TPS6510x series has an integrated VCOM
buffer to power the LCD backplane. For LCD panels
powered by 5 V only, the TPS6510x series has a
linear regulator controller using an external transistor
to provide a regulated 3.3-V output for the digital
circuits. For maximum safety, the TPS65100/05 goes
into shutdown as soon as one of the outputs is out of
regulation. The device can be enabled again by
toggling the input or the enable (EN) pin to GND.
The TPS65101 does not enter shutdown when one
of the outputs is below its power good threshold.
APPLICATIONS
•
•
•
•
•
•
The TPS6510x series offers a compact and small
power supply solution that provides all three voltages
required by thin film transistor (TFT) LCD displays.
The auxiliary linear regulator controller can be used
to generate a 3.3-V logic power rail for systems
powered by a 5-V supply rail only.
TFT LCD Displays for Notebooks
TFT LCD Displays for Monitors
Portable DVD Players
Tablet PCs
Car Navigation Systems
Industrial Displays
TPS6510x
Vin
2.7 V to 5.8 V
Boost
Converter
Vo1
Up to 15 V / 400 mA
Positive Charge
Pump
Vo3
Up to 30 V / 20 mA
Negative
Charge Pump
Vo2
Up to 12 V / 20 mA
Vcom Buffer
Vcom
Linear Regulator
Controller
Vo4
3.3 V
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PowerPAD is a trademark of Texas Instruments.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2003–2006, Texas Instruments Incorporated
TPS65100, TPS65101
TPS65105
www.ti.com
SLVS496C – SEPTEMBER 2003 – REVISED APRIL 2006
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
TYPICAL APPLICATION CIRCUIT
L1
4.7 µH
VI
2.7 to 5.8 V
C3
22 µF
TPS65100
VIN
COMP
R7
C1
0.22 µF
R8
VO2
Up to 12 V/20 mA
D2
C12
C4
22 µF
0.22 µF
SW
SW
VCOMIN
FB1
EN
SUP
C2
ENR
D3
R3
C6
0.22 µF
C5
R1
C11
10 nF
VO1
VO1
Up to 15 V/350 mA
D1
C2+
C2−/MODE
C1+
C1−
0.22 µF
R2
Vo3
up to 30 V/20 mA
OUT3
DRV
FB3
FB2
VCOM
REF
FB4
PGND
R5
PGND
BASE
C7
0.22 µF
GND
R4
R6
C11
220 nF
Q1
BCP68
VI
VO4
3.3 V
C9
1 µF
Vcom
C8
1 µF
C10
4.7 µF
ORDERING INFORMATION
TA
-40°C to
85°C
(1)
(2)
2
PACKAGE (1) (2)
LINEAR REGULATOR
OUTPUT VOLTAGE
MINIMUM SWITCH
CURRENT LIMIT
TSSOP
QFN
PACKAGE
MARKING
3.3 V
1.6 A
TPS65100PWP
TPS65100RGE
TPS65100
3.3 V
1.6 A
TPS65101PWP
TPS65101RGE
TPS65101
3.3 V
0.96 A
TPS65105PWP
TPS65105RGE
TPS65105
The PWP and RGE packages are available taped and reeled. Add an R suffix to the device type (TPS65100PWPR) to order the device
taped and reeled. The PWPR package has quantities of 2000 devices per reel, and the the RGER package has 3000 devices per reel.
Without suffix the PWP package only, is shipped in tubes with 60 devices per tube.
For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI
Web site at www.ti.com.
Submit Documentation Feedback
TPS65100, TPS65101
TPS65105
www.ti.com
SLVS496C – SEPTEMBER 2003 – REVISED APRIL 2006
ABSOLUTE MAXIMUM RATINGS
over operating free-air temperature range (unless otherwise noted) (1)
UNIT
Voltages on pin VIN (2)
-0.3 V to 6 V
(2)
-0.3 V to 15.5 V
ENR (2)
-0.3 V to VI + 0.3 V
Voltages on pin VO1, SUP, PG
Voltages on pin EN, MODE,
Voltage on VCOMIN
14 V
Voltage on pin SW (2)
20 V
Continuous power dissipation
See Dissipation Rating Table
Operating junction temperature range
-40°C to 150°C
Storage temperature range
-65°C to 150°C
Lead temperature (soldering, 10 sec)
(1)
(2)
260°C
Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating
conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
All voltage values are with respect to network ground terminal.
DISSIPATION RATINGS
PACKAGE
RΘJA
TA ≤ 25°C
POWER RATING
TA = 70°C
POWER RATING
TA = 85°C
POWER RATING
24-Pin TSSOP
30.13 C°/W (PWP soldered)
3.3 W
1.83 W
1.32 W
24-Pin QFN
30 C°/W
3.3 W
1.8 W
1.3 W
RECOMMENDED OPERATING CONDITIONS
MIN
TYP
MAX
VIN
Input voltage range
L
Inductor (1)
TA
Operating free-air temperature
-40
85
°C
TJ
Operating junction temperature
-40
125
°C
(1)
2.7
UNIT
5.8
V
µH
4.7
See the application information section for further information.
ELECTRICAL CHARACTERISTICS
Vin = 3.3 V, EN = VIN, VO1 = 10 V, TA = -40°C to 85°C, typical values are at TA = 25°C (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
SUPPLY CURRENT
Vi
Input voltage range
IQ
Quiescent current into VIN
IQCharge
2.7
5.8
V
mA
ENR = VCOMIN = GND, VO3 = 2 x VO1,
Boost converter not switching
0.7
0.9
Charge pump quiescent
current into SUP
VO1 = SUP = 10 V, VO3 = 2 x VO1
1.7
2.7
VO1 = SUP = 10 V, VO3 = 3 x VO1
3.9
6
IQVCOM
VCOM quiescent current into
SUP
ENR = GND, VO1 = SUP = 10 V
750
1300
µA
IQEN
LDO controller quiescent
current into VIN
ENR = VIN, EN = GND
300
800
µA
ISD
Shutdown current into VIN
EN = ENR = GND
1
10
µA
VUVLO
Undervoltage lockout
threshold
VIN falling
2.2
2.4
V
Thermal shutdown
Temperature rising
160
mA
°C
LOGIC SIGNALS EN, ENR
VIH
High-level input voltage
VIL
Low-level input voltage
1.5
V
0.4
Submit Documentation Feedback
V
3
TPS65100, TPS65101
TPS65105
www.ti.com
SLVS496C – SEPTEMBER 2003 – REVISED APRIL 2006
ELECTRICAL CHARACTERISTICS (continued)
Vin = 3.3 V, EN = VIN, VO1 = 10 V, TA = -40°C to 85°C, typical values are at TA = 25°C (unless otherwise noted)
PARAMETER
IIleak
Input leakage current
TEST CONDITIONS
MIN
EN = GND or VIN
TYP
MAX
UNIT
0.01
0.1
µA
15
V
MAIN BOOST CONVERTER
VO1
Output voltage range
5
VO1 - VI
Minimum input to output
voltage difference
1
VREF
Reference voltage
1.205
1.213
1.219
VFB
Feedback regulation voltage
1.136
1.146
1.154
V
IFB
Feedback input bias current
10
100
nA
rDS(ON)
N-MOSFET on-resistance
(Q1)
VO1 = 10 V, Isw = 500 mA
195
290
VO1 = 5 V, Isw = 500 mA
285
420
ILIM
N-MOSFET switch current
limit (Q1)
TPS65100, TPS65101
rDS(ON)
P-MOSFET on-resistance
(Q2)
IMAX
Maximum P-MOSFET peak
switch current
Ileak
Switch leakage current
fSW
Oscillator frequency
V
V
mΩ
1.6
2.3
2.6
A
0.96
1.37
1.56
A
VO1 = 10 V, Isw = 100 mA
9
15
VO1 = 5 V, Isw = 100 mA
14
22
TPS65105
Vsw = 15 V
1
A
1
10
µA
0°C ≤ TA ≤ 85°C
1.295
1.6
2.1
-40°C ≤ TA ≤ 85°C
1.191
1.6
2.1
Line regulation
2.7 V ≤ VI ≤ 5.7 V, Iload = 100 mA
Load regulation
0 mA ≤ IO ≤ 300 mA
Ω
MHz
0.012
%/V
0.2
%/A
NEGATIVE CHARGE PUMP VO2
VO2
Output voltage range
Vref
Reference voltage
VFB
Feedback regulation voltage
IFB
rDS(ON)
IO
-2
V
1.205
1.213
1.219
-36
0
36
mV
Feedback input bias current
10
100
nA
Q8 P-Channel switch rDS(ON)
4.3
8
2.9
4.4
Q9 N-Channel switch rDS(ON)
IO = 20 mA
Maximum output current
20
Line regulation
7 V ≤ VO1 ≤ 15 V, Iload = 10 mA, VO2 = -5 V
Load regulation
1 mA ≤ IO ≤ 20 mA, VO2 = -5 V
V
Ω
mA
0.09
%/V
0.126
%/mA
POSITIVE CHARGE PUMP VO3
VO3
Output voltage range
Vref
Reference voltage
1.205
VFB
Feedback regulation voltage
1.187
IFB
rDS(ON)
30
V
1.213
1.219
V
1.214
1.238
V
Feedback input bias current
10
100
nA
Q3 P-Channel switch rDS(ON)
9.9
15.5
1.1
1.8
4.6
8.5
1.2
2.2
610
720
Q4 N-Channel switch rDS(ON)
Q5 P-Channel switch rDS(ON)
IO = 20 mA
Q6 N-Channel switch rDS(ON)
Vd
D1 – D4 Shottky diode
forward voltage
IO
Maximum output current
ID1-D4 = 40 mA
20
Ω
mV
mA
Line regulation
10 V ≤ VO1 ≤ 15 V, Iload = 10 mA, VO3 = 27 V
0.56
%/V
Load regulation
1 mA ≤ IO ≤ 20 mA, VO3 = 27 V
0.05
%/mA
LINEAR REGULATOR CONTROLLER VO4
VO4
4
Output voltage
4.5 V ≤ VI ≤ 5.5V, 10 mA ≤ IO ≤ 500 mA
Submit Documentation Feedback
3.2
3.3
3.4
V
TPS65100, TPS65101
TPS65105
www.ti.com
SLVS496C – SEPTEMBER 2003 – REVISED APRIL 2006
ELECTRICAL CHARACTERISTICS (continued)
Vin = 3.3 V, EN = VIN, VO1 = 10 V, TA = -40°C to 85°C, typical values are at TA = 25°C (unless otherwise noted)
PARAMETER
IBASE
TEST CONDITIONS
Maximum base drive current
VI - VO4 - VBE ≥ 0.5 V
(1)
VI - VO4 - VBE ≥ 0.75 V
MIN
TYP
13.5
19
20
27
(1)
Line regulation
4.75 V ≤ VI ≤ 5.5 V, Iload = 500 mA
Load regulation
1 mA ≤ IO ≤ 500 mA, VI = 5 V
Start up current
VO4 ≤ 0.8 V
MAX
mA
0.186
%/V
0.064
11
UNIT
%/A
20
25
mA
VCOM BUFFER
Vcm
Common mode input range
Vos
Input offset voltage
DC Load regulation
2.25
(VO1)-2
IO = 0 mA
-25
+25
IO = ±25 mA
-30
37
IO = ±50 mA
-45
55
IO = ±100 mA
-72
85
IO = ±150 mA
IB
VCOMIN Input bias current
Ipeak
Peak output current
-97
-300
V
mV
mV
110
-30
300
nA
VO1 = 15 V
1.2
A
VO1 = 10 V
0.65
A
VO1 = 5 V
0.15
A
VO1 Rising
-12
-8.75%
VO1
-6
V
VO2 Rising
-13
-9% VO2
-5
V
VO3 Rising
-11
-8% VO3
-5
V
FAULT PROTECTION THRESHOLDS
V(th, Vo1)
V(th, Vo2)
Shutdown threshold
V(th, Vo3)
With VI = supply voltage of the TPS6510x, VO4 = output voltage of the regulator, VBE = basis emitter voltage of external transistor
DEVICE INFORMATION
7
8
20
19
18
17
9
16
10
15
11
14
12
13
C1+
DRV
COMP
1
24 23 22 21 20 19
18
ENR
2
17
C2+
16
OUT3
15
FB3
14
VCOMIN
EN
3
FB1
4
FB4
5
BASE
6
Exposed
Thermal Die*
7
8
Submit Documentation Feedback
9 10 11 1213
C2−/MODE
VCOM
SUP
5
6
C1−
21
PGND
22
4
GND
3
EN
ENR
COMP
FB2
REF
GND
DRV
C1−
C1+
C2−/MODE
C2+
OUT3
PGND
23
REF
2
SW
24
SW
1
VIN
FB1
FB4
BASE
VIN
SW
SW
PGND
PGND
SUP
VCOM
VCOMIN
FB3
RGE PACKAGE
TOP VIEW
FB2
PWP PACKAGE
TOP VIEW
Thermal PAD*
(1)
5
TPS65100, TPS65101
TPS65105
www.ti.com
SLVS496C – SEPTEMBER 2003 – REVISED APRIL 2006
DEVICE INFORMATION (continued)
Terminal Functions
TERMINAL
NO.
(PWP)
NO.
(RGE)
I/O
VIN
4
7
I
Input voltage pin of the device
EN
24
3
I
Enable pin of the device. This pin should be terminated and not be left floating. A logic
high enables the device and a logic low shuts down the device.
COMP
22
1
VCOMIN
11
14
I
Positive input terminal of the VCOM buffer. When the VCOM buffer is not used, this
terminal can be connected to GND to reduce the overall quiescent current of the IC.
ENR
23
2
I
Enable pin of the linear regulator controller. This pin should be terminated and not be
left floating. Logic high enables the regulator and a logic low puts the regulator in
shutdown.
C1+
16
19
Positive terminal of the charge pump flying capacitor
C1-
17
20
Negative terminal of the charge pump flying capacitor
DRV
18
21
O
External charge pump driver
FB2
21
24
I
Feedback pin of negative charge pump
REF
20
23
O
Internal reference output typically 1.23 V
FB4
2
5
I
Feedback pin of the linear regulator controller. The linear regulator controller is set to
a fixed output voltage of 3.3 V or 3 V depending on the version.
O
Base drive output for the external transistor
NAME
Compensation pin for the main boost converter. A small capacitor is connected to this
pin.
BASE
3
6
GND
19
22
PGND
7, 8
10, 11
VCOM
10
13
O
VCOM buffer output
FB3
12
15
I
Feedback pin of positive charge pump
OUT3
13
16
O
Positive charge pump output
C2-/MODE
15
18
Negative terminal of the charge pump flying capacitor and charge pump MODE pin. If
the flying capacitor is connected to this pin, the converter operates in a voltage tripler
mode. If the charge pump needs to operate in a voltage doubler mode, the flying
capacitor is removed and the C2-/MODE pin should be connected to GND.
C2+
14
17
Positive terminal for the charge pump flying capacitor. If the device runs in voltage
doubler mode, this pin should be left open.
12
I
Supply pin of the positive, negative charge pump, boost converter gate drive circuit,
and VCOM buffer. This pin should be connected to the output of the main boost
converter and cannot be connected to any other voltage source. For performance
reasons, it is not recommended for a bypass capacitor to be connected directly to this
pin.
SUP
9
Ground
Power ground
FB1
1
4
I
Feedback pin of the boost converter
SW
5, 6
8, 9
I
Switch pin of the boost converter
PowerPAD™/
Thermal Die
6
DESCRIPTION
The PowerPad or exposed thermal die needs to be connected to the power ground
pins (PGND)
Submit Documentation Feedback
TPS65100, TPS65101
TPS65105
www.ti.com
SLVS496C – SEPTEMBER 2003 – REVISED APRIL 2006
FUNCTIONAL BLOCK DIAGRAM
VIN
SW
SW
Q2
FB1
FB2
FB3
Bias Vref = 1.213 V
Thermal Shutdown
Start-Up Sequencing
Undervoltage Detection
Short-Circuit Protection
S
D
Main boost
converter
EN
Current Limit
and
Soft Start
1.6-MHz
Oscillator
SUP
Control Logic
Gate Drive Circuit
D
Q1
S
COMP
GM Amplifier
Comparator
Sawtooth
Generator
FB1
VFB
1.146 V
SUP
SUP
(VO)
FB3
Positive
Charge Pump
GM Amplifier
Low Gain
VFB
1.146 V
Vref
1.214 V
Negative
Charge Pump
SUP
Q8
D
Q3
S
Current
Control
C1−
Gain Select
(Doubler or
Tripple Mode)
D
Q4
S
SUP
Soft Start
D
C1+
Current
Control
Soft Start
S
DRV
D
Q7
S
D
Q9
SUP
SUP
S
Vo3
D1
D2
D Q5
D4
S
C2+
FB2
D
Vref
0V
S
D3
Q6
C2−
Reference
Output
REF
Vref
1.213 V
SUP
Vin
Soft Start
Iref = 20 mA
Soft Start
Short Circuit
Detect
D
Q11
S
~1 V
FB4
VCOM
D
Linear
Regulator
Controller
S
Vref
1.213 V
D
Q12
S
Q10
Disable
VCOM
Buffer
ENR
BASE
VCOMIN
Submit Documentation Feedback
GND
PGND
PGND
7
TPS65100, TPS65101
TPS65105
www.ti.com
SLVS496C – SEPTEMBER 2003 – REVISED APRIL 2006
TYPICAL CHARACTERISTICS
Table of Graphs
FIGURE
Main Boost Converter
Efficiency, main boost converter VO1
vs Load current
1
Efficiency, main boost converter VO1
vs Load current
2
Efficiency
vs Input voltage
3
fsw
Switching frequency
vs Free-air temperature
4
rDS(on)
rDS(on) N-Channel main switch Q1
vs Free-air temperature
5
η
PWM operation, continuous mode
6
PWM operation at light load
7
Load transient response, CO = 22 µF
8
Load transient response, CO = 2 x 22 µF
9
Power-up sequencing
10
Soft start VO1
11
Negative Charge Pump
Imax
VO2 Maximum load current
vs Output voltage VO1
12
Positive Charge Pump
Imax
VO3 Maximum load current
vs Output voltage VO1 (doubler mode)
13
Imax
VO3 Maximum load current
vs Output voltage VO1 (tripler mode)
14
EFFICIENCY
vs
LOAD CURRENT
100
100
90
90
Vo1 = 15 V
40
30
70
Vo1 = 10 V
60
50
Vo1 = 15 V
40
Vo1 = 6 V
90
Vo1 = 10 V
85
Vo1 = 15 V
80
30
VI = 3.3 V
Vo2, Vo3 = No Load, Switching
20
10
10
100
IL − Load Current − mA
Figure 1.
1k
75
VI = 5 V
Vo2, Vo3 = No Load, Switching
20
10
1
8
ILoad at Vo1 = 100 mA
Vo2, Vo3 = No Load, Switching
Efficiency - %
Efficiency − %
60
50
100
80
Vo1 = 10 V
70
EFFICIENCY
vs
INPUT VOLTAGE
95
Vo1 = 6 V
80
Efficiency − %
EFFICIENCY
vs
LOAD CURRENT
1
10
100
IL − Load Current − mA
Figure 2.
Submit Documentation Feedback
1k
70
2.5
3
3.5
4
4.5
5
VI - Input V oltage - V
Figure 3.
5.5
6
TPS65100, TPS65101
TPS65105
www.ti.com
SLVS496C – SEPTEMBER 2003 – REVISED APRIL 2006
SWITCHING FREQUENCY
vs
FREE-AIR TEMPERATURE
rDS(on) N-CHANNEL MAIN SWITCH
vs
FREE-AIR TEMPERATURE
350
r
− N−Channel Main Switch − mΩ
DS(on)
Switching Frequency − MHz
1.9
1.8
VI = 2.7 V
1.7
VI = 3.3 V
1.6
VI = 5.8 V
1.5
1.4
1.3
−40
PWM OPERATION CONTINUOUS
MODE
−20
0
20
40
60
80
100
VSW
10 V/div
300
Vo1 = 5 V
250
VO
50 mV/div
200
Vo1 = 10 V
150
IL
1 A/div
Vo1 = 15 V
100
−40
−20
0
20
40
60
80
VI = 3.3 V
VO = 10 V/300 mA
100
250 ns/div
TA − Free-Air Temperature − °C
TA − Free-Air Temperature − °C
Figure 4.
Figure 5.
Figure 6.
PWM OPERATION AT LIGHT LOAD
LOAD TRANSIENT RESPONSE
LOAD TRANSIENT RESPONSE
VI = 3.3 V
Vo1 = 10 V, CO= 2*22 µF
Vo1
200 mV/div
VSW
10 V/div
Vo1
100 mV/div
VO
50 mV/div
VI = 3.3 V
VO = 10 V/10 mA
IO
50 mA to 250 mA
IL
500 mA/div
VI = 3.3 V
Vo1 = 10 V, CO= 22 µF
IO
50 mA to 250 mA
100 µs/div
100 µs/div
250 ns/div
Figure 7.
Figure 8.
POWER-UP SEQUENCING
SOFT START VO1
Figure 9.
VO2 MAXIMUM LOAD CURRENT
0.20
VI = 3.3 V
VO = 10 V,
IO = 300 mA
Vo2 = −8 V
0.18
I O − Output Current − A
Vo1
5 V/div
Vo1
5 V/div
Vo2
5 V/div
Vo3
10 V/div
VCOM
2 V/div
VI = 3.3 V
VO = 10 V,
VCOM CI = 1 nF
500 µs/div
TA = −40°C
0.16
II
500
mA/div
0.14
TA = 85°C
0.12
0.10
TA = 25°C
0.08
0.06
0.04
0.02
500 µs/div
0
8.8
9.8
10.8
11.8
12.8
13.8
14.8
Vo1 − Output Voltage − V
Figure 10.
Figure 11.
Submit Documentation Feedback
Figure 12.
9
TPS65100, TPS65101
TPS65105
www.ti.com
SLVS496C – SEPTEMBER 2003 – REVISED APRIL 2006
VO3 MAXIMUM LOAD CURRENT
VO3 MAXIMUM LOAD CURRENT
0.14
0.12
TA = −40°C
Vo3 = 18 V (Doubler Mode)
0.10
TA = −40°C
I O − Output Current − A
I O − Output Current − A
0.12
TA = 85°C
0.10
TA = 25°C
0.08
0.06
0.04
TA = 25°C
0.08
TA = 85°C
0.06
0.04
0.02
0.02
Vo3 = 28 V (Tripler Mode)
0
9
10
11
12
13
14
15
0
9
10
Vo1 − Output Voltage − V
11
12
13
14
15
Vo1 − Output Voltage − V
Figure 13.
Figure 14.
DETAILED DESCRIPTION
The TPS6510x series consists of a main boost converter operating with a fixed switching frequency of 1.6 MHz
to allow for small external components. The boost converter output voltage VO1 is also the input voltage,
connected via the pin SUP, for the positive and negative charge pumps and the bias supply for the VCOM
buffer. The linear regulator controller is independent from this system with its own enable pin. This allows the
linear regulator controller to continue to operate while the other supply rails are disabled or in shutdown due to a
fault condition on one of their outputs. See the functional block diagram for more information.
Main Boost Converter
The main boost converter operates with PWM and a fixed switching frequency of 1.6 MHz. The converter uses a
unique fast response, voltage mode controller scheme with input voltage feedforward. This achieves excellent
line and load regulation (0.2% A load regulation typical) and allows the use of small external components. To
add higher flexibility to the selection of external component values the device uses external loop compensation.
Although the boost converter looks like a nonsynchronous boost converter topology operating in discontinuous
mode at light load, the TPS6510x series maintains continuous conduction even at light load currents. This is
accoplished using the Virtual Synchronous Converter Technology for improved load transient response. This
architecture uses an external Schottky diode and an integrated MOSFET in parallel connected between SW and
SUP (see the functional block diagram). The integrated MOSFET Q2 allows the inductor current to become
negative at light load conditions. For this purpose, a small integrated P-channel MOSFET with typically 10 Ω
rDSon is sufficient. When the inductor current is positive, the external Schottky diode with the lower forward
voltage conducts the current. This causes the converter to operate with a fixed frequency in continuous
conduction mode over the entire load current range. This avoids the ringing on the switch pin as seen with a
standard nonsynchronous boost converter and allows a simpler compensation for the boost converter.
VCOM Buffer
VCOMIN is the input of the VCOM buffer. If the VCOM buffer is not required for certain applications, it is
possible to shut down the VCOM buffer by statically connecting VCOMIN to ground, reducing the overall
quiescent current. The VCOM buffer features soft start avoiding a large voltage drop at VO1 during start-up. The
VCOMIN cannot be pulled dynamically to ground during operation.
Enable and Power On Sequencing (EN, ENR)
The device has two enable pins. These pins should be terminated and not left floating to prevent unpredictable
operation. Pulling the enable pin (EN) high enables the device and starts the power on sequencing with the main
boost converter VO1 coming up first then the negative and positive charge pump and the VCOM buffer. If the
VCOMIN pin is held low, the VCOM buffer remains disabled. The linear regulator has an independent enable pin
(ENR). Pulling this pin low disables the regulator, and pulling this pin high enables this regulator.
If the enable pin EN is pulled high, the device starts its power on sequencing. The main boost converter starts
up first with its soft start. If the output voltage has reached 91.25% of its output voltage, the negative charge
10
Submit Documentation Feedback
TPS65100, TPS65101
TPS65105
www.ti.com
SLVS496C – SEPTEMBER 2003 – REVISED APRIL 2006
DETAILED DESCRIPTION (continued)
pump comes up next. The negative charge pump starts with a soft start and when the output voltage has
reached 91% of the nominal value, the positive charge pump comes up with a soft start. The VCOM buffer is
enabled as soon as the positive charge pump has reached its nominal value and VCOMIN is greater than
typically 1.0 V. Pulling the enable pin low shuts down the device. Depended on load current and output
capacitance, each of the outputs goes down.
Positive Charge Pump
The TPS6510x series has a fully regulated integrated positive charge pump generating VO3. The input voltage
for the charge pump is applied to the SUP pin that is equal to the output of the main boost converter VO1. The
charge pump is capable of supplying a minimum load current of 20 mA. Depending on the voltage difference
between VO1 and VO3 higher load currents are possible. See Figure 13 and Figure 14.
Negative Charge Pump
The TPS6510x series has a regulated negative charge pump using two external Schottky diodes. The input
voltage for the charge pump is applied to the SUP pin that is connected to the output of the main boost
converter VO1. The charge pump inverts the main boost converter output voltage and is capable of supplying a
minimum load current of 20 mA. Depending on the voltage difference between VO1 and VO2, higher load
currents are possible. See Figure 12.
Linear Regulator Controller
The TPS6510x series includes a linear regulator controller to generate a 3.3-V rail which is useful when the
system is powered from a 5-V supply. The regulator is independent from the other voltage rails of the device and
has its own enable (ENR). Since most of the systems require this voltage rail to come up first it is recommended
to use a R-C delay on EN. This delays the start-up of the main boost converter which will reduce the inrush
current as well.
Soft Start
The main boost converter as well as the charge pumps, linear regulator, and VCOM buffer have an internal soft
start. This avoids heavy voltage drops at the input voltage rail or at the output of the main boost converter VO1
during start-up caused by high inrush currents. See Figure 10 and Figure 11. During softstart of the main boost
converter VO1 the internal current limit threshold is increased in three steps. The device starts with the first step
where the current limit is set to 2/5 of the typical current limit (2/5 of 2.3A) for 1024 clock cycles then increased
to 3/5 of the current limit for 1024 clock cycles and the 3rd step is the full current limit. The TPS65101 has an
extended softstart time where each step is 2048 clock cycles.
Fault Protection
All the outputs of the TPS65100/05 have short circuit detection where the device enters shutdown. The
TPS65101, as an exception, does not enter shutdown in case one of the outputs falls below its power good
threshold. The main boost converter has overvoltage and undervoltage protection. If the output voltage VO1 rises
above the overvoltage protection threshold of typically 5% of VO1, then the device stops switching but remains
operational. When the output voltage falls below this threshold again, then the converter continues operation.
When the output voltage falls below power good threshold of typically 8.75% of VO1, in case of a short circuit
condition, then the TPS65100/05 goes into shutdown. Because there is a direct pass from the input to the output
through the diode, the short circuit condition remains. If this condition needs to be avoided, a fuse at the input or
an output disconnect using a single transistor and resistor is required. The negative and positive charge pumps
have an undervoltage lockout to protect the LCD panel of possible latch-up conditions in case of a short circuit
condition or faulty operation. When the negative output voltage is typically above 9.5% of its output voltage
(closer to ground), then the device enters shutdown. When the positive charge pump output voltage VO3 is
below 8% typ of its output voltage, then the device goes into shutdown as well. See the electrical characteristics
table under fault protection thresholds. The device can be enabled again by toggling the enable pin (EN) below
0.4 V or by cycling the input voltage below the UVLO of 1.7 V. The linear regulator reduces the output current to
typical 20 mA under a short circuit condition when the output voltage is typically < 1 V. See the functional block
diagram. The linear regulator does not go into shutdown under a short-circuit condition.
Submit Documentation Feedback
11
TPS65100, TPS65101
TPS65105
www.ti.com
SLVS496C – SEPTEMBER 2003 – REVISED APRIL 2006
DETAILED DESCRIPTION (continued)
Thermal Shutdown
A thermal shutdown is implemented to prevent damage due to excessive heat and power dissipation. Typically,
the thermal shutdown threshold is 160°C. If this temperature is reached, the device goes into shutdown. The
device can be enabled by toggling the enable pin to low and back to high or by cycling the input voltage to GND
and back to VI again.
12
Submit Documentation Feedback
TPS65100, TPS65101
TPS65105
www.ti.com
SLVS496C – SEPTEMBER 2003 – REVISED APRIL 2006
APPLICATION INFORMATION
BOOST CONVERTER DESIGN PROCEDURE
The first step in the design procedure is to calculate the maximum possible output current of the main boost
converter under certain input and output voltage conditions. The following example is for a 3.3-V to 10-V
conversion:
Vin = 3.3 V, Vout = 10 V, Switch voltage drop Vsw = 0.5 V, Schottky diode forward voltage VD = 0.8 V
1. Duty cycle:
Vout V V
D
in 10 V 0.8 V 3.3 V 0.73
D
V out V V sw
10 V 0.8 V 0.5 V
D
2. Average inductor current:
I
I out 300 mA 1.11 A
L
1 0.73
1D
3. Inductor peak-to-peak ripple current:
i L
Vin Vsw D
fs L
(3.3 V 0.5 V) 0.73
304 mA
1.6 MHz 4.2 H
4. Peak switch current:
i
I
I L 1.11 A 304 mA 1.26 A
swpeak
L
2
2
The integrated switch, the inductor, and the external Schottky diode must be able to handle the peak switch
current. The calculated peak switch current has to be equal to or lower than the minimum N-MOSFET switch
current limit as specified in the electrical characteristics table (1.6 A for the TPS65100/01 and 0.96 A for the
TPS65105). If the peak switch current is higher, then the converter cannot support the required load current.
This calculation must be done for the minimum input voltage where the peak switch current is highest. The
calculation includes conduction losses like switch rDSon (0.5 V) and diode forward drop voltage losses (0.8 V).
Additional switching losses, inductor core and winding losses, etc., require a slightly higher peak switch current
in the actual application. The above calculation still allows a for good design and component selection.
Inductor Selection
Several inductors work with the TPS6510x series. Especially with the external compensation, the performance
can be adjusted to the specific application requirements. The main parameter for inductor selection is the
saturation current of the inductor which should be higher than the peak switch current as calculated above with
additional margin to cover for heavy load transients and extreme start-up conditions. Another method is to
choose the inductor with a saturation current at least as high as the minimum switch current limit of 1.6 A for the
TPS65100/01 and 0.96 A for the TPS65105. The different switch current limits allow selection of a physically
smaller inductor when less output current is required. The second important parameter is inductor dc resistance.
Usually, the lower the DC resistance, the higher the efficiency. However, inductor DC resistance, is not the only
parameter determining the efficiency. Especially for a boost converter where the inductor is the energy storage
elemen,t the type and material of the inductor influences the efficiency as well. Especially at the high switching
frequency of 1.6 MHz, inductor core losses, proximity effects, and skin effects become more important. Usually,
an inductor with a larger form factor yields higher efficiency. The efficiency difference between different inductors
can vary between 2% to 10%. For the TPS6510x series, inductor values between 3.3 µH and 6.8 µH are a good
choice but other values can be used as well. Possible inductors are shown in Table 1.
Submit Documentation Feedback
13
TPS65100, TPS65101
TPS65105
www.ti.com
SLVS496C – SEPTEMBER 2003 – REVISED APRIL 2006
APPLICATION INFORMATION (continued)
Table 1. Inductor Selection
DEVICE
TPS65100
TPS65105
INDUCTOR VALUE
COMPONENT SUPPLIER
DIMENSIONS / mm
ISAT/DCR
4.7 µH
Coilcraft DO1813P-472HC
8,89 x 6,1 x 5
2.6 A/54 mΩ
4.2 µH
Sumida CDRH5D28 4R2
5,7 x 5,7 x 3
2.2 A/23 mΩ
4.7 µH
Sumida CDC5D23 4R7
6 x 6 x 2,5
1.6 A/48 mΩ
3.3 µH
Wuerth Elektronik 744042003
4,8 x 4,8 x 2
1.8 A/65 mΩ
4.2 µH
Sumida CDRH6D12 4R2
6,5 x 6,5 x 1,5
1.8 A/60 mΩ
3.3 µH
Sumida CDRH6D12 3R3
6,5 x 6,5 x 1,5
1.9 A/50 mΩ
3.3 µH
Sumida CDPH4D19 3R3
5,1 x 5,1 x 2
1.5 A/26 mΩ
3.3 µH
Coilcraft DO1606T-332
6,5 x 5,2 x 2
1.4 A/120 mΩ
3.3 µH
Sumida CDRH2D18/HP 3R3
3,2 x 3,2 x 2
1.45 A/69 mΩ
4.7 µH
Wuerth Elektronik 744010004
5,5 x 3,5 x 1
1.0 A/260 mΩ
3.3 µH
Coilcraft LPO6610-332M
6,6 x 5,5 x 1
1.3 A/160 mΩ
Output Capacitor Selection
For the best output voltage filtering, a low ESR output capacitor is recommended. Ceramic capacitors have a
low ESR value, but depending on the application, tantalum capacitors can be used as well. A 22-µF ceramic
output capacitor works for most of the applications. Higher capacitor values can be used to improve the load
transient regulation. See Table 2 for selection of the output capacitor. The output voltage ripple can be
calculated as:
Ip L
I
V out out 1 I p ESR
Cout
f s Vout V V
d
in
with:
IP = Peak switch current as calculated in the previous section with ISW(peak).
L = Selected inductor value
IOUT = Normal load current
fs = Switching frequency
Vd = Rectifier diode forward voltage (typical 0.3 V)
COUT = Selected output capacitor
ESR = Output capacitor ESR value
Input Capacitor Selection
For good input voltage filtering, low ESR ceramic capacitors are recommended. A 22-µF ceramic input capacitor
is sufficient for most of the applications. For better input voltage filtering, this value can be increased. See
Table 2 and the typical applications for input capacitor recommendations.
Table 2. Input and Output Capacitors Selection
CAPACITOR
VOLTAGE RATING
COMPONENT SUPPLIER
COMMENTS
22 µF/1210
16 V
Taiyo Yuden EMK325BY226MM
Cout
22 µF/1206
6.3 V
Taiyo Yuden JMK316BJ226
Cin
Rectifier Diode Selection
To achieve high efficiency, a Schottky diode should be used. The voltage rating should be higher than the
maximum output voltage of the converter. The average forward current should be equal to the average inductor
current of the converter. The main parameter influencing the efficiency of the converter is the forward voltage
and the reverse leakage current of the diode; both should be as low as possible. Possible diodes are: On
Semiconductor MBRM120L, Microsemi UPS120E, and Fairchild Semiconductor MBRS130L.
14
Submit Documentation Feedback
TPS65100, TPS65101
TPS65105
www.ti.com
SLVS496C – SEPTEMBER 2003 – REVISED APRIL 2006
Converter Loop Design and Stability
The TPS6510x series converter loop can be externally compensated and allows access to the internal
transconductance error amplifier output at the COMP pin. A small feedforward capacitor across the upper
feedback resistor divider speeds up the circuit as well. To test the converter stability and load transient
performance of the converter, a load step from 50 mA to 250 mA is applied, and the output voltage of the
converter is monitored. Applying load steps to the converter output is a good tool to judge the stability of such a
boost converter.
Design Procedure Quick Steps
1. Select the feedback resistor divider to set the output voltage.
2. Select the feedforward capacitor to place a zero at 50 kHz.
3. Select the compensation capacitor on pin COMP. The smaller the value, the higher the low frequency gain.
4. Use a 50-kΩ potentiometer in series to Cc and monitor Vout during load transients. Fine tune the load
transient by adjusting the potentiometer. Select a resistor value that comes closest to the potentiometer
resistor value. This needs to be done at the highest Vin and highest load current since the stability is most
critical at these conditions.
Setting the Output Voltage and Selecting the Feedforward Capacitor
The output voltage is set by the external resistor divider and is calculated as:
V out 1.146 V 1 R1
R2
Across the upper resistor a bypass capacitor is required to speed up the circuit during load transients as shown
in Figure 15.
VO1
Up to 10 V/150 mA
D1
C8
6.8 pF
SW
SW
R1
430 kΩ
C4
22 µF
FB1
SUP
C2+
C2−/MODE
C2
0.22 µF
R2
56 kΩ
Figure 15. Feedforward Capacitor
Together with R1 the bypass capacitor C8 sets a zero in the control loop at approximately 50 kHz:
1
ƒz 2 C8 R1
A value closest to the calculated value should be used. Larger feedforward capacitor values reduce the load
regulation of the converter and cause load steps as shown in Figure 16.
Submit Documentation Feedback
15
TPS65100, TPS65101
TPS65105
www.ti.com
SLVS496C – SEPTEMBER 2003 – REVISED APRIL 2006
Load Step
Figure 16. Load Step Caused By A Too Large Feedforward Capacitor Value
Compensation
The regulator loop can be compensated by adjusting the external components connected to the COMP pin. The
COMP pin is connected to the output of the internal transconductance error amplifier. A typical compensation
scheme is shown in Figure 17.
RC
15 kΩ
CC
VIN
COMP
1 nF
Figure 17. Compensation Network
The compensation capacitor CC adjusts the low frequency gain and the resistor value adjusts the high frequency
gain. The formula below calculates at what frequency the resistor increases the high frequency gain.
1
fz 2 Cc Rc
Lower input voltages require a higher gain and therefore a lower compensation capacitor value. A good start is
CC = 1 nF for a 3.3-V input and CC = 2.2 nF for a 5-V input. If the device operates over the entire input voltage
range from 2.7 V to 5.8 V, a large compensation capacitor up to 10 nF is recommended. Figure 18 shows the
load transient with a larger compensation capacitor, and Figure 19 shows a smaller compensation capacitor.
Figure 18. Cc = 4.7 nF
16
Submit Documentation Feedback
TPS65100, TPS65101
TPS65105
www.ti.com
SLVS496C – SEPTEMBER 2003 – REVISED APRIL 2006
Figure 19. Cc = 1 nF
Lastly, Rc needs to be selected. A good practice is to use a 50-kΩ potentiometer and adjust the potentiometer
for best load transient where no oscillations should occur. These tests have to be done at the highest Vin and
highest load current because converter stability is most critical under these conditions. Figure 20, Figure 21, and
Figure 22 show the fine tuning of the loop with Rc.
Figure 20. Overcompensated (Damped Oscillation), Rc Is Too Large
Figure 21. Undercompensated (Loop Is Too Slow), Rc Is Too Small
Submit Documentation Feedback
17
TPS65100, TPS65101
TPS65105
www.ti.com
SLVS496C – SEPTEMBER 2003 – REVISED APRIL 2006
Figure 22. Optimum, Rc Is Ideal
Negative Charge Pump
The negative charge pump provides a regulated output voltage by inverting the main output voltage VO1. The
negative charge pump output voltage is set with external feedback resistors.
The maximum load current of the negative charge pump depends on the voltage drop across the external
Schottky diodes, the internal on resistance of the charge pump MOSFETS Q8 and Q9, and the impedance of
the flying capacitor C12. When the voltage drop across these components is larger than the voltage difference
from VO1 to VO2, the charge pump is in dropout, providing the maximum possible output current. Therefore, the
higher the voltage difference between VO1 and VO2, the higher the possible load current. See Figure 12 for the
possible output current versus boost converter voltage VO1.
VO(min) = -(VO - 2 VD - Io (2 x rDS(on)Q8 + 2 x rDS(on)Q9 + Xcfly))
Setting the output voltage:
VOUT = -VREF x R3 = -1.213 V x R3
R4
R4
|VOUT|
|VOUT|
R3 = R4 x
= R4 x
VREF
1.213
The lower feedback resistor value R4 should be in a range between 40 kΩ to 120 kΩ or the overall feedback
resistance should be within 500 kΩ to 1 MΩ. Smaller values load the reference too heavily and larger values
may cause stability problems. The negative charge pump requires two external Schottky diodes. The peak
current rating of the Schottky diode has to be twice the load current of the output. For a 20-mA output current,
the dual Schottky diode BAT54 or similar is a good choice.
Positive Charge Pump
The positive charge pump can be operated in a voltage doubler mode or a voltage tripler mode depending on
the configuration of the C2+ and C2-/MODE pins. Leaving the C2+ pin open and connecting C2-/MODE to GND
forces the positive charge pump to operate in a voltage doubler mode. If higher output voltages are required, the
positive charge pump can be operated as a voltage tripler. To operate the charge pump in the voltage tripler
mode, a flying capacitor needs to be connected to C2+ and C2-/MODE.
The maximum load current of the positive charge pump depends on the voltage drop across the internal
Schottky diodes, the internal on resistance of the charge pump MOSFETS, and the impedance of the flying
capacitor. When the voltage drop across these components is larger than the voltage difference VO1 x 2 to VO3
(doubler mode) or VO1 x 3 to VO3 (tripler mode), then the charge pump is in dropout, providing the maximum
possible output current. Therefore, the higher the voltage difference between VO1 x 2 (doubler) or VO1 x 3
(tripler) to VO3, the higher the possible load current. See Figure 13 and Figure 14 for the output current versus
boost converter voltage VO1 and the following calculations.
Voltage doubler:
VO3max = 2 x VO1 - (2 VD + 2 x Io x (2 x rDS(on)Q5 + rDS(on)Q3 + rDS(on)Q4 + XC1))
Voltage tripler:
VO3max = 3 x VO1 - (3 x VD + 2 x Io x (3 x rDS(on)Q5 + rDS(on)Q3 + rDS(on)Q4 + XC1 + XC2))
18
Submit Documentation Feedback
TPS65100, TPS65101
TPS65105
www.ti.com
SLVS496C – SEPTEMBER 2003 – REVISED APRIL 2006
The output voltage is set by the external resistor divider and is calculated as:
V out 1.214 1 R5
R6
R5 R6 Vout
V
FB
1
R6 V out
1
1.214
VCOM Buffer
The VCOM buffer is typically used to drive the backplane of a TFT panel. The VCOM output voltage is typically
set to half of the main output voltage VO1 plus a small shift to implement the specific compensation voltage. The
TFT video signal gets coupled through the TFT storage capacitor plus the LCD cell capacitance to the output of
the VCOM buffer. Because of these, short current pulses in the positive and negative direction appear at the
output of the VCOM buffer. To minimize the output voltage ripple caused by the current pulses, a
transconductance amplifier having a current source output and an output capacitor is used. The output capacitor
supports the high frequency part of the current pulses drawn from the LCD panel. The VCOM buffer only needs
to handle the low frequency portion of the current pulses. A 1-µF ceramic output capacitor is sufficient for most
of the applications. When using other output capacitor values it is important to keep in mind that the output
capacitor is part of the VCOM buffer loop stabilization.
The VCOM buffer has an integrated soft start to avoid voltage drops on VO1 during start-up. The soft start is
implemented as such that the VCOMIN is held low until the VCOM buffer is fully biased and the common mode
range is reached. Then the positive input is released and the VCOM buffer output slowly comes up. Usually a
1-nF capacitor on VCOMIN to GND is used to filter high frequency noise coupled in from VO1. The size of this
capacitor together with the upper feedback resistor value determines the start-up time. The larger the capacitor
from VCOMIN to GND, the slower the soft start.
Linear Regulator Controller
The TPS6510x series includes a linear regulator controller to generate a 3.3-V rail when the system is powered
from a 5-V supply. Because an external npn transistor is required, the input voltage of the TPS6510x series
applied to VIN needs to be higher than the output voltage of the regulator. To provide a minimum base drive
current of 13.5 mA, a minimum internal voltage drop of 500 mV from Vin to Vbase is required. This can be
translated into a minimum input voltage on VIN for a certain output voltage as the following calculation shows:
VINmin= VO4 + VBE + 0.5 V
The base drive current together with the hFE of the external transistor determines the possible output current.
Using a standard npn transistor like the BCP68 allows an output current of 1 A and using the BCP54 allows a
load current of 337 mA for an input voltage of 5 V. Other transistors can be used as well depending on the
required output current, power dissipation, and PCB space. The device is stable with a 4.7-µF ceramic output
capacitor. Larger output capacitor values can be used to improve the load transient response when higher load
currents are required.
Layout Considerations
For all switching power supplies, the layout is an important step in the design, especially at high-peak currents
and switching frequencies. If the layout is not carefully designed, the regulator might show stability and EMI
problems. Therefore, the traces carrying high-switching currents should be routed first using wide and short
traces. The input filter capacitor should be placed as close as possible to the input pin VIN of the IC. See the
evaluation module (EVM) for a layout example.
Thermal Information
An influential component of thermal performance of a package is board design. To take full advantage of the
heat dissipation abilities of the PowerPAD or QFN package with exposed thermal die, a board that acts similar to
a heat sink and allows the use of an exposed (and solderable) deep downset pad should be used. For further
information, see the Texas Instrumens application notes (SLMA002) PowerPAD Thermally Enhanced Package,
and (SLMA004) PowerPAD Made Easy. For the QFN package, see the application report (SLUA271) QFN/SON
PCB Attachement. Especially for the QFN package it is required to solder down the Thermal Pad to achieve the
required thermal resistance.
Submit Documentation Feedback
19
TPS65100, TPS65101
TPS65105
www.ti.com
SLVS496C – SEPTEMBER 2003 – REVISED APRIL 2006
VI
3.3 V
L1
3.3 µH
C3
22 µF
Vo1
R9
15 kΩ
R7
500 kΩ
C14
1 nF
C5
0.22 µF
VIN
COMP
R8
500 kΩ
D2
VO2
−5 V/20 mA
R3
620 kΩ
C8
6.8 pF
TPS65100
C9
1 nF
C1
0.22 µF
C12
0.22 µF
D3
SW
SW
VCOMIN
FB1
EN
SUP
ENR
C1+
C1−
DRV
C2+
C2−/MODE
C2
0.22 µF
R1
430 kΩ
VO3
23 V/20 mA
FB3
VCOM
REF
FB4
PGND
PGND
C4
22 µF
R2
56 kΩ
OUT3
FB2
BASE
VO1
10 V/300 mA
D1
R5
1M
C6
0.22 µF
GND
R3
150 kΩ
R6
56 kΩ
C11
220 nF
Vcom
5V
C7
1 µF
Figure 23. Typical Application, Notebook supply
20
Submit Documentation Feedback
TPS65100, TPS65101
TPS65105
www.ti.com
SLVS496C – SEPTEMBER 2003 – REVISED APRIL 2006
L1
4.7 µH
CDRH5D18−4R1
Vin
5V
C3
22 µF
R9
4.3 kΩ
R7
500 kΩ
VO1
VIN
COMP
VCOMIN
C14
1 nF
VO2
−7 V/20 mA
R8
500 kΩ
C1
0.22 µF
C12
0.22 µF
D2
C6
0.22 µF
C5
3.3 pF
TPS65100
C9
2.2 nF
R3
750 kΩ
D3
EN
ENR
C1+
C1−
DRV
FB2
REF
FB4
BASE
VO1
13.5 V/400 mA
D1
SW
SW
FB1
SUP
R2
75 kΩ
C2+
C2−/MODE
VO3
23 V/20 mA
OUT3
FB3
VCOM
PGND
PGND
C7
0.22 µF
R5
1 MΩ
GND
R4
130 kΩ
C11
220 nF
C4
22 µF
R1
820 kΩ
R6
56 kΩ
Q1
BCP68
Vin
C12
1 µF
VO4
3.3 V/500 mA
C10
4.7 µF
Vcom
7V
C8
1 µF
Figure 24. Typical Application, Monitor Supply
Submit Documentation Feedback
21
PACKAGE OPTION ADDENDUM
www.ti.com
7-Nov-2014
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
TPS65100PWP
ACTIVE
HTSSOP
PWP
24
60
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 85
TPS65100
TPS65100PWPG4
ACTIVE
HTSSOP
PWP
24
60
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 85
TPS65100
TPS65100PWPR
ACTIVE
HTSSOP
PWP
24
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 85
TPS65100
TPS65100PWPRG4
ACTIVE
HTSSOP
PWP
24
TBD
Call TI
Call TI
-40 to 85
TPS65100RGER
ACTIVE
VQFN
RGE
24
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 85
TPS
65100
TPS65101PWP
ACTIVE
HTSSOP
PWP
24
60
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 85
TPS65101
TPS65101PWPR
ACTIVE
HTSSOP
PWP
24
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 85
TPS65101
TPS65101RGER
ACTIVE
VQFN
RGE
24
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 85
TPS
65101
TPS65105PWP
ACTIVE
HTSSOP
PWP
24
60
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 85
TPS65105
TPS65105PWPG4
ACTIVE
HTSSOP
PWP
24
60
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 85
TPS65105
TPS65105PWPR
ACTIVE
HTSSOP
PWP
24
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 85
TPS65105
TPS65105RGER
ACTIVE
VQFN
RGE
24
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 85
TPS
65105
TPS65105RGERG4
ACTIVE
VQFN
RGE
24
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 85
TPS
65105
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
7-Nov-2014
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF TPS65100 :
• Automotive: TPS65100-Q1
NOTE: Qualified Version Definitions:
• Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
26-Jan-2013
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
TPS65100PWPR
Package Package Pins
Type Drawing
SPQ
HTSSOP
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
PWP
24
2000
330.0
16.4
6.95
8.3
1.6
8.0
16.0
Q1
TPS65100RGER
VQFN
RGE
24
3000
330.0
12.4
4.25
4.25
1.15
8.0
12.0
Q2
TPS65101PWPR
HTSSOP
PWP
24
2000
330.0
16.4
6.95
8.3
1.6
8.0
16.0
Q1
TPS65101RGER
VQFN
RGE
24
3000
330.0
12.4
4.25
4.25
1.15
8.0
12.0
Q2
TPS65105PWPR
HTSSOP
PWP
24
2000
330.0
16.4
6.95
8.3
1.6
8.0
16.0
Q1
TPS65105RGER
VQFN
RGE
24
3000
330.0
12.4
4.25
4.25
1.15
8.0
12.0
Q2
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
26-Jan-2013
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
TPS65100PWPR
HTSSOP
PWP
24
2000
367.0
367.0
38.0
TPS65100RGER
VQFN
RGE
24
3000
367.0
367.0
35.0
TPS65101PWPR
HTSSOP
PWP
24
2000
367.0
367.0
38.0
TPS65101RGER
VQFN
RGE
24
3000
367.0
367.0
35.0
TPS65105PWPR
HTSSOP
PWP
24
2000
367.0
367.0
38.0
TPS65105RGER
VQFN
RGE
24
3000
367.0
367.0
35.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2016, Texas Instruments Incorporated
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement