Yamaha | STAGEPAS150M | Specifications | Yamaha 150M DJ Equipment User Manual

EN
Troubleshooting
Owner ’s Manual
CAUTION
Explanation of Graphical Symbols
RISK OF ELECTRIC SHOCK
DO NOT OPEN
Power does not turn on
The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the
presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to persons.
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
• Is the included power cord correctly connected to a power outlet?
Unit: mm
■ Speaker
■ Mixer
160
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the literature accompanying the product.
The above warning is located on the bottom
of the mixer and the rear of the speaker.
Introduction
Dimentions
Power shuts down suddenly
power off. Turn on the power again only after the mixer cools, since it cannot be turned on until the internal
temperature goes down. Reduce the volume with the MASTER LEVEL control so that the LIMITER indicator
flashes only briefly in response to the highest transient peaks.
Features
● Two-way, 8-inch (20 cm) speaker system
The built-in speaker delivers high-quality powerful sound from an exceptionally compact cabinet.
The scratch-resistant speaker is rugged enough for outdoor use.
● Powered mixer
The powered mixer is a convenient, high-performance all-in-one unit that includes EQ and reverb. With two
monaural inputs and three stereo inputs, the STAGEPAS 150M can be connected to a wide range of
instruments and devices.
● Convenient storage
The STAGEPAS 150M can be used in even the most cramped quarters, inside or outside, since the mixer is
built into the speaker cabinet.
• Is the vent on the top panel of the mixer blocked?
1
Read these instructions.
2
Keep these instructions.
3
Heed all warnings.
4
Follow all instructions.
5
Do not use this apparatus near water.
6
Clean only with dry cloth.
7
Do not block any ventilation openings. Install in accordance with the
manufacturer's instructions.
12 Use only with the cart, stand, tripod, bracket, or table specified
by the manufacturer, or sold with the apparatus. When a cart is
used, use caution when moving the cart/apparatus combination
to avoid injury from tip-over.
8
Do not install near any heat sources such as radiators, heat registers, stoves, or
other apparatus (including amplifiers) that produce heat.
automatically and the power may be turned off. Turn on the power again only after the mixer cools, since it
9
Do not defeat the safety purpose of the polarized or grounding-type plug. A
polarized plug has two blades with one wider than the other. A grounding type
plug has two blades and a third grounding prong. The wide blade or the third
prong are provided for your safety. If the provided plug does not fit into your
outlet, consult an electrician for replacement of the obsolete outlet.
No sound is heard
14 Refer all servicing to qualified service personnel. Servicing is required when the
apparatus has been damaged in any way, such as power-supply cord or plug is
damaged, liquid has been spilled or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture, does not operate normally, or
has been dropped.
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.
(UL60065_03)
• Is the SPEAKER jack connected to the included speaker (300S)?
Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical
shock, short-circuiting, damages, fire or other hazards. These precautions include, but are not limited to, the following:
• Only use the voltage specified as correct for the device. The required
voltage is printed on the name plate of the device.
• Are both XLR type and phone type jacks on channels 1–2 being used (connected) at the same time?
• Use only the included power cord.
Please connect to only one of these jacks on each channel.
Use a screwdriver or coin to turn each screw on the mixer from LOCK to
OPEN until it clicks.
• Is the input signal from the connected device set to an appropriate level?
Sound is not loud enough
• Are the LEVEL controls of all relevant channels and/or the MASTER LEVEL control set to appropriate levels?
LOCK
OPEN
OPEN
• Are the MIC/LINE switches of each channels set appropriately?
OPEN
LOCK
• Are both XLR type and phone type jacks on channels 1–2 being used (connected) at the same time?
LOCK
OPEN
• Do not place the power cord near heat sources such as heaters or
radiators, and do not excessively bend or otherwise damage the cord,
place heavy objects on it, or place it in a position where anyone could
walk on, trip over, or roll anything over it.
• Be sure to connect to an appropriate outlet with a protective grounding
connection. Improper grounding can result in electrical shock.
LOCK
LOCK
Power supply/Power cord
• Are the MIC/LINE switches of each channels set appropriately?
OPEN
Please connect to only one of these jacks on each channel.
Do not open
• Do not open the device or attempt to disassemble the internal parts or
modify them in any way. The device contains no user-serviceable parts.
If it should appear to be malfunctioning, discontinue use immediately and
have it inspected by qualified Yamaha service personnel.
Water warning
• Do not expose the device to rain, use it near water or in damp or wet
conditions, or place containers on it containing liquids which might spill
into any openings. If any liquid such as water seeps into the device, turn
off the power immediately and unplug the power cord from the AC outlet.
Then have the device inspected by qualified Yamaha service personnel.
Securely hold the mixer’s handles to remove it from the speaker.
• Are the REVERB switches of each channels set to ON (
)?
• Is the REVERB control set to an appropriate level?
• If the power cord or plug becomes frayed or damaged, or if there is a
sudden loss of sound during use of the device, or if any unusual smells
or smoke should appear to be caused by it, immediately turn off the
power switch, disconnect the electric plug from the outlet, and have the
device inspected by qualified Yamaha service personnel.
• If this device should be dropped or damaged, immediately turn off the
power switch, disconnect the electric plug from the outlet, and have the
device inspected by qualified Yamaha service personnel.
Getting a more powerful sound from the speakers
• Is the SPEECH/MUSIC switch set to MUSIC (
)?
• Remove the electric plug from the outlet when the device is not to be used
for extended periods of time, or during electrical storms.
• When removing the electric plug from the device or an outlet, always hold
the plug itself and not the cord. Pulling by the cord can damage it.
• Are the Equalizer controls (HIGH/LOW) set to appropriate levels?
Location
Getting a clearer sound for announcements
• Is the SPEECH/MUSIC switch set to SPEECH (
Use only the mixer's handles when removing the mixer from the speaker and when carrying the mixer
Caution
NOTE:
separate from the speaker.
The mixer can also be used when installed in the speaker.
When you install the mixer into the speaker, make sure to match the indentations on the speaker cabinet to
the corresponding parts on the mixer, and then turn each screw from OPEN to LOCK until it clicks.
)?
• Are the Equalizer controls (HIGH/LOW) set to appropriate levels?
Outputting the signal to a main mixer
• Connect a main mixer to the ST SUB OUT jack. The ST SUB OUT jack outputs the signal prior to routing
through the MASTER LEVEL control. Adjust the level of output signal from the ST SUB OUT jack with the ST
SUB OUT control. The ST SUB OUT control does not affect the MASTER LEVEL control. If only the L (left)
ST SUB OUT jack is used, the mixer mixes the left and right signals and sends them to the jack.
Turning the power on/off
1
2
• When setting up the device, make sure that the AC outlet you are using is
easily accessible. If some trouble or malfunction occurs, immediately turn
off the power switch and disconnect the plug from the outlet. Even when
the power switch is turned off, electricity is still flowing to the product at
the minimum level. When you are not using the product for a long time,
make sure to unplug the power cord from the wall AC outlet.
• Do not use the device in a confined, poorly-ventilated location. Make sure
that there is adequate space between the mixer and surrounding walls or
other devices: at least 30 cm at the sides, 30 cm behind and 30 cm
above. If the mixer is to be used installed into the speaker cabinet, make
sure to allow adequate space between the speaker and the surrounding
walls or other devices: at least 30 cm at the sides, 30 cm behind and 30
cm above. Inadequate ventilation can result in overheating, possibly
causing damage to the device(s), or even fire.
• Do not use the speaker's handles for suspended installation. Doing so
can result in damage or injury.
Be sure that the mixer’s power switch is turned off.
Block Diagram
Connect the included power cord to the [AC IN] jack, and plug the power
cord into a power outlet.
• Before moving the device, remove all connected cables.
• Avoid setting all equalizer controls and faders to their maximum.
Depending on the condition of the connected devices, doing so may
cause feedback and may damage the speakers.
• Do not expose the device to excessive dust or vibrations, or extreme cold
or heat (such as in direct sunlight, near a heater, or in a car during the
day) to prevent the possibility of panel disfiguration or damage to the
internal components.
• Do not place the device in an unstable position where it might
accidentally fall over.
• To avoid any loud, unexpected noise from the speakers, first turn on the power to those connected
Caution
devices that are closest to the sound source.
Example: Sound source (CD player or instrument) → STAGEPAS 150M
• Do not block the vents. This mixer has ventilation holes at the top to
prevent the internal temperature from becoming too high. In particular, do
not place the device on its side or upside down. Inadequate ventilation
can result in overheating, possibly causing damage to the device(s), or
even fire.
• Do not use the device in the vicinity of a TV, radio, stereo equipment,
mobile phone, or other electric devices. Doing so may result in noise,
both in the device itself and in the TV or radio next to it.
When turning off the power to the system, reverse the order described above.
• Before turning on the power, set the LEVEL controls and MASTER LEVEL control to their minimum setting (zero).
3
Press the mixer’s power switch to the ON position.
The POWER indicator lights.
To turn the power off, press the power switch to the OFF position.
The POWER indicator turns off.
Connections
• Before connecting the device to other devices, turn off the power for all
devices. Before turning the power on or off for all devices, set all volume
levels to minimum.
• For the SPEAKER jack, use only the included speaker (300S) and speaker
cable. Use of other types of speakers and cables may result in damage to
the device(s), or even fire.
(5)-5
Hum & Noise (Equivalent Input Noise, Rs = 150Ω, MIC/LINE = MIC)
-112 dBu (CH1/2)
-65 dBu Residual output noise (SPEAKER)
■ Speaker (300S)
Enclosure
2 way bass-reflex type, Polypropylene, Black
Crossover Frequency
4.0 kHz (LF: 12 dB/oct, HF: 12 dB/oct)
Frequency Range
55 Hz-20 kHz (-10 dB)
Speaker Unit
LF: 8" (20 cm) Cone
HF: 1" (2.54cm) Compression Driver
Crosstalk (1 kHz)
-70 dB between input channels
1.
IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!This product, when installed as
indicated in the instructions contained in this manual, meets FCC requirements.
Modifications not expressly approved by Yamaha may void your authority, granted by
the FCC, to use the product.
2.
IMPORTANT: When connecting this product to accessories and/or another product
use only high quality shielded cables. Cable/s supplied with this product MUST be
used. Follow all installation instructions. Failure to follow instructions could void your
FCC authorization to use this product in the USA.
3.
NOTE: This product has been tested and found to comply with the requirements listed
in FCC Regulations, Part 15 for Class "B" digital devices. Compliance with these
requirements provides a reasonable level of assurance that your use of this product in
a residential environment will not result in harmful interference with other electronic
devices. This equipment generates/uses radio frequencies and, if not installed and
used according to the instructions found in the users manual, may cause interference
harmful to the operation of other electronic devices. Compliance with FCC regulations
does not guarantee that interference will not occur in all installations. If this product is
found to be the source of interference, which can be determined by turning the unit
"OFF" and "ON", please try to eliminate the problem by using one of the following
measures:Relocate either this product or the device that is being affected by the
interference.
Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or
install AC line filter/s.
In the case of radio or TV interference, relocate/reorient the antenna. If the antenna
lead-in is 300 ohm ribbon lead, change the lead-in to co-axial type cable.
If these corrective measures do not produce satisfactory results, please contact the
local retailer authorized to distribute this type of product. If you can not locate the
appropriate retailer, please contact Yamaha Corporation of America, Electronic Service
Division, 6600 Orangethorpe Ave, Buena Park, CA90620
The above statements apply ONLY to those products distributed by Yamaha
Corporation of America or its subsidiaries.
* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA.
Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage
to the device or other property. These precautions include, but are not limited to, the following:
Power supply/Power cord
Total Harmonic Distortion
0.5 % @ 20 Hz, 1 kHz, 20 kHz +14 dBu GAIN= nominal (ST SUB OUT, ST LINK OUT)
Stereo Input Channel Equalization
±15 dB
HIGH 10 kHz shelving
LOW 100 Hz shelving
FCC INFORMATION (U.S.A.)
If you notice any abnormality
CAUTION
Reverb is not applied to the sound
Weight
9.6 kg (Speaker + Powered Mixer)
• Never insert or remove an electric plug with wet hands.
• Is the input signal from the connected device set to an appropriate level?
3
Power Consumption
20 W
Frequency Response (Nomimal output level @ 1 kHz)
-3 dB, 0 dB, +1 dB @ 20 Hz-20 kHz (MUSIC/SPEECH=MUSIC) (ST SUB OUT)
-3 dB, 0 dB, +1 dB @ 80 Hz-20 kHz (MUSIC/SPEECH = SPEECH) (ST LINK OUT)
-3 dB, 0 dB, +1 dB @ 20 Hz-20 kHz, 1 W Output (MUSIC/SPEECH=MUSIC, without
Speaker EQ) (SPEAKER)
WARNING
• If sound is not still output, contact your Yamaha dealer.
• Are the LEVEL controls of all relevant channels and/or the MASTER LEVEL control set to appropriate levels?
Specifications and descriptions in this owner's manual are for information purposes only. Yamaha Corp. reserves the right to change or modify products or specifications at
any time without prior notice. Since specifications, equipment or options may not be the same in every locale, please check with your Yamaha dealer.
Maximum Output Level
112 dB (1 m)
PLEASE READ CAREFULLY BEFORE PROCEEDING
* Please keep this manual in a safe place for future reference.
Sound is distorted or noise is produced
Specifications
Maximum Output Power
150 W (±10 %)/4Ω @ 10 % THD at 1 kHz (SPEAKER)
100 W/4Ω @ 1 % THD at 1 kHz (SPEAKER)
PRECAUTIONS
The mixer is installed in the speaker when the STAGEPAS 150M leaves the factory.
Be sure that the mixer’s power switch is turned off.
120
■ General Specifications
• Are the LEVEL controls of all relevant channels and/or the MASTER LEVEL control set to appropriate levels?
• Is the CLICK switch (for headphones) set to OFF?
Remove the mixer
96.3
2-M8x25
• Are external instruments (including a microphone) or speakers correctly connected to the mixer?
Speaker (300S), mixer, power cord, speaker cable, Owner’s Manual (this booklet)
Before turning on the mixer
255
275
13 Unplug this apparatus during lightning storms or when unused
for long periods of time.
WARNING
faulty. Check that the speaker cable is correctly connected to the mixer and reapply the power.
1
2
11 Only use attachments/accessories specified by the manufacturer.
• Is the POWER indicator flashing? There may be a short in the speaker cable or the connection may be
Package Contents
NOTE:
10 Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
Since inadequate ventilation can result in overheating the mixer, the protection circuit may come on
cannot be turned on until the internal temperature goes down.
290
If the mixer is used at a volume beyond the permissible level, the protection circuit automatically turns the
455.5
IMPORTANT SAFETY INSTRUCTIONS
• Is the volume set at high for an extended period of time?
137
Thank you for your purchase of the Yamaha PORTABLE PA SYSTEM STAGEPAS 150M. The STAGEPAS 150M
is a versatile, compact PA system consisting of a speaker and a mixer.
In order to get the most out of your new STAGEPAS 150M and its sophisticated functions, we suggest you
read through this manual thoroughly. Also keep it in a safe place for future reference.
Handling caution
• When turning on the AC power in your audio system, always turn on the
device LAST, to avoid speaker damage. When turning the power off, the
device should be turned off FIRST for the same reason.
• Do not insert your fingers or hands in any gaps or openings on the device
(vents,, ports, etc.).
• Avoid inserting or dropping foreign objects (paper, plastic, metal, etc.)
into any gaps or openings on the device (vents, ports, etc.) If this
happens, turn off the power immediately and unplug the power cord from
the AC outlet. Then have the device inspected by qualified Yamaha
service personnel.
• Do not use the device or headphones for a long period of time at a high
or uncomfortable volume level, since this can cause permanent hearing
loss. If you experience any hearing loss or ringing in the ears, consult a
physician.
• Do not operate the device if the sound is distorting. Prolonged use in this
condition could cause overheating and result in fire.
• Do not rest your weight on the device or place heavy objects on it, and
avoid use excessive force on the buttons, switches or connectors.
IMPORTANT NOTICE FOR THE UNITED KINGDOM
Connecting the Plug and Cord
WARNING: THIS APPARATUS MUST BE EARTHED
IMPORTANT. The wires in this mains lead are coloured in accordance with the following
code:
GREEN-AND-YELLOW : EARTH
BLUE
: NEUTRAL
BROWN
: LIVE
Using a cell phone near the speaker system can induce noise. If this occurs,
move the cell phone further away from the speaker system.
Air blowing out of the bass reflex ports is normal, and often occurs when the
speaker is handling program material with heavy bass content.
Yamaha cannot be held responsible for damage caused by improper use
or modifications to the device.
Always turn the power off when the device is not in use.
As the colours of the wires in the mains lead of this apparatus may not correspond with the
coloured markings identifying the terminals in your plug proceed as follows:
The wire which is coloured GREEN-and-YELLOW must be connected to the terminal in the plug
which is marked by the letter E or by the safety earth symbol
or colored GREEN or GREENand-YELLOW.
The wire which is coloured BLUE must be connected to the terminal which is marked with the
letter N or coloured BLACK.
The wire which is coloured BROWN must be connected to the terminal which is marked with the
letter L or coloured RED.
• This applies only to products distributed by Yamaha-Kemble Music (U.K.) Ltd.
(3 wires)
For details of products, please contact your nearest Yamaha representative or the authorized distributor listed below.
NORTH AMERICA
CANADA
Yamaha Canada Music Ltd.
135 Milner Avenue, Scarborough, Ontario, M1S 3R1, Canada
Tel: 416-298-1311
ASIA
POLAND
Yamaha Music Central Europe GmbH
Sp.z. o.o. Oddzial w Polsce
ul. 17 Stycznia 56, PL-02-146 Warszawa, Poland
Tel: 022-868-07-57
U.S.A.
THE NETHERLANDS/
BELGIUM/LUXEMBOURG
Yamaha Corporation of America
6600 Orangethorpe Ave., Buena Park, Calif. 90620, U.S.A.
Tel: 714-522-9011
Yamaha Music Central Europe GmbH, Branch Benelux
Clarissenhof 5-b, 4133 AB Vianen, The Netherlands
Tel: 0347-358 040
CENTRAL & SOUTH AMERICA
MEXICO
Yamaha de México S.A. de C.V.
Calz. Javier Rojo Gómez #1149, Col. Guadalupe del Moral
C.P. 09300, México, D.F., México
Tel: 55-5804-0600
BRAZIL
Interference From Cell Phones
(class B)
Yamaha Musical do Brasil Ltda.
Rua Joaquim Floriano, 913 - 4' andar, Itaim Bibi, CEP 04534013 Sao Paulo, SP. BRAZIL
Tel: 011-3704-1377
ARGENTINA
Yamaha Music Latin America, S.A.
Sucursal de Argentina
Viamonte 1145 Piso2-B 1053, Buenos Aires, Argentina
Tel: 1-4371-7021
PANAMA AND OTHER LATIN
AMERICAN COUNTRIES/
CARIBBEAN COUNTRIES
Yamaha Music Latin America, S.A.
Torre Banco General, Piso 7, Urbanización Marbella,
Calle 47 y Aquilino de la Guardia,
Ciudad de Panamá, Panamá
Tel: +507-269-5311
FRANCE
Yamaha Musique France
BP 70-77312 Marne-la-Vallée Cedex 2, France
Tel: 01-64-61-4000
ITALY
Yamaha Musica Italia S.P.A. Combo Division
Viale Italia 88, 20020 Lainate (Milano), Italy
Tel: 02-935-771
Yamaha Música Ibérica, S.A.
Ctra. de la Coruna km. 17, 200, 28230
Las Rozas (Madrid), Spain
Tel: 91-639-8888
DENMARK
YS Copenhagen Liaison Office
Generatorvej 6A . DK-2730 Herlev, Denmark
Tel: 44 92 49 00
NORWAY
Norsk filial av Yamaha Scandinavia AB
Grini Næringspark 1
N-1345 Østerås, Norway
Tel: 67 16 77 70
GERMANY
OTHER EUROPEAN COUNTRIES
Yamaha Music Central Europe GmbH
Siemensstraße 22-34, 25462 Rellingen,Germany
Tel: 04101-3030
Yamaha Music Central Europe GmbH
Siemensstraße 22-34, 25462 Rellingen, Germany
Tel: +49-4101-3030
• This applies only to products distributed by YAMAHA CORPORATION OF AMERICA.
(Ser.No)
Yamaha Music Central Europe GmbH,
Branch Austria, CEE Department
Schleiergasse 20, A-1100 Wien, Austria
Tel: 01-602039025
Yamaha KHS Music Co., Ltd.
3F, #6, Sec.2, Nan Jing E. Rd. Taipei. Taiwan 104, R.O.C.
Tel: 02-2511-8688
THAILAND
Siam Music Yamaha Co., Ltd.
891/1 Siam Motors Building, 15-16 floor Rama 1 road,
Wangmai, Pathumwan Bangkok 10330, Thailand
Tel: 02-215-2626
OCEANIA
AUSTRALIA
Yamaha Music Australia Pty. Ltd.
Level 1, 99 Queensbridge Street, Southbank,
Victoria 3006, Australia
Tel: 3-9693-5111
COUNTRIES AND TRUST TERRITORIES IN
PACIFIC OCEAN
AFRICA
Yamaha Corporation, Asia-Pacific Music Marketing Group
Nakazawa-cho 10-1, Naka-ku, Hamamatsu,
Japan 430-8650
Tel: +81-53-460-2313
Yamaha Corporation, Asia-Pacific Music Marketing Group
Nakazawa-cho 10-1, Naka-ku, Hamamatsu,
Japan 430-8650
Tel: +81-53-460-2313
HEAD OFFICE
MIDDLE EAST
CZECH REPUBLIC/SLOVAKIA/
HUNGARY/SLOVENIA
MALAYSIA
Yamaha Corporation, Asia-Pacific Music Marketing Group
Nakazawa-cho 10-1, Naka-ku, Hamamatsu, Japan 430-8650
Tel: +81-53-460-2317
RUSSIA
SWITZERLAND/LIECHTENSTEIN
Yamaha Music Central Europe GmbH, Branch Austria
Schleiergasse 20, A-1100 Wien, Austria
Tel: 01-60203900
Yamaha Music Korea Ltd.
8F, 9F, Dongsung Bldg. 158-9 Samsung-Dong, Kangnam-Gu,
Seoul, Korea
Tel: 080-004-0022
OTHER ASIAN COUNTRIES
Yamaha Music U.K. Ltd.
Sherbourne Drive, Tilbrook, Milton Keynes, MK7 8BL, England
Tel: 01908-366700
AUSTRIA
KOREA
TAIWAN
• The illustrations as shown in this manual are for instructional purposes
only, and may be different from the ones on your equipment.
Yamaha Music Central Europe GmbH, Branch Switzerland
Seefeldstrasse 94, 8008 Zürich, Switzerland
Tel: 01-383 3990
PT. Yamaha Music Indonesia (Distributor) PT. Nusantik
Gedung Yamaha Music Center, Jalan Jend. Gatot Subroto
Kav. 4, Jakarta 12930, Indonesia
Tel: 21-520-2577
Yamaha Music Asia Pte., Ltd.
#03-11 A-Z Building 140 Paya Lebor Road, Singapore 409015
Tel: 747-4374
Yamaha Scandinavia AB
J. A. Wettergrens Gata 1, Box 30053
S-400 43 Göteborg, Sweden
Tel: 031 89 34 00
Yamaha Music (Russia)
Office 4015, entrance 2, 21/5 Kuznetskii
Most street, Moscow, 107996, Russia
Tel: 495 626 0660
IMPORTANT
Please record the serial number of this unit in the space below.
Model:
Serial No.:
The serial number is located on the bottom or rear of the unit.
Retain this Owner's Manual in a safe place for future reference.
INDONESIA
SINGAPORE
SWEDEN
THE UNITED KINGDOM
• The company names and product names in this manual are the
trademarks or registered trademarks of their respective companies.
Yamaha Music & Electronics (China) Co.,Ltd.
25/F., United Plaza, 1468 Nanjing Road (West),
Jingan, Shanghai, China
Tel: 021-6247-2211
Yamaha Music Malaysia, Sdn., Bhd.
Lot 8, Jalan Perbandaran, 47301 Kelana Jaya,
Petaling Jaya, Selangor, Malaysia
Tel: 3-78030900
SPAIN/PORTUGAL
The performance of components with moving contacts, such as switches,
volume controls, and connectors, deteriorates over time. Consult qualified
Yamaha service personnel about replacing defective components.
EUROPE
THE PEOPLE'S REPUBLIC OF CHINA
TURKEY/CYPRUS
Yamaha Music Central Europe GmbH
Siemensstraße 22-34, 25462 Rellingen, Germany
Tel: 04101-3030
Yamaha Corporation, Pro Audio & Digital Musical
Instrument Division
Nakazawa-cho 10-1, Naka-ku, Hamamatsu,
Japan 430-8650
Tel: +81-53-460-2441
OTHER COUNTRIES
Yamaha Music Gulf FZE
LOB 16-513, P.O.Box 17328, Jubel Ali, Dubai, United Arab
Emirates
Tel: +971-4-881-5868
Yamaha Pro Audio global web site: http://www.yamahaproaudio.com/
Yamaha Manual Library:
http://www.yamaha.co.jp/manual/
PA19
U.R.G., Pro Audio & Digital Musical Instrument Division, Yamaha Corporation
©2007 Yamaha Corporation
712MW-01A0 Printed in China
Quick Guide
Connection Example 1
Included speaker
(300S)
Getting sound out of the system
Controls and Functions
Powered speaker
(Yamaha MSR100)
Instrument/device with stereo output
(synthesizer, etc.)
Microphone
CD player
Using the included speaker, set up the system and try it out.
1
Connect the included speaker (300S) to the SPEAKER jack. Connect the sources (microphone, other
instruments) to the input jacks. For details, see “Connection Example.”
Caution
3 SPEAKER jack
1 AC IN jack
Connect the included speaker and your instruments to the mixer.
Connect the included power cord here.
Electric
guitar
R
L
Before connecting any devices, make sure to turn off the power for all devices (including microphones).
Also, before turning the power on or off, set the volume levels on all devices to minimum.
Headphones
L
R
Caution
Computer
(for recording)
Computer
(for playback)
NOTE: For best results when connecting an electric guitar or bass guitar to the mixer, use a direct box, preamp
(guitar amp), or amp simulator.
Be sure to use the included power
cord. Use of other cords may result
in malfunction, heat generation, or
fire.
9 Channel input jacks (CH 1, 2)
(for included speaker 300S only)
For connecting a guitar, microphone, keyboard or other instrument/device. Set the MIC/LINE switch to MIC
This outputs the mixed monaural L+R signal
or LINE for channels 1, 2, depending on the level of the input signal.
channels from 1 to 7/8 and the level is adjusted
XLR-type connectors are wired as follows (IEC60268 standard): pin 1: ground, pin 2: hot (+), and pin 3: cold (-).
with the MASTER LEVEL control. Connect only the
NOTE: On any given channel, you may use either XLR or phone jack, but not both. Please connect to only one of
these jacks on each channel.
included speaker (300S).
2 POWER switch
4 ST LINK OUT R jack
For turning the power to the mixer on and off.
This outputs signals from R (even) channels only.
) Stereo channel input jacks (CH 3/4, 5/6, 7/8)
Input the left and right channels of a stereo signal into the respective odd and even channels of the mixer.
When inserting a plug to this jack, only signals from
2
These inputs are intended mainly for use with instruments and equipment having stereo outputs, such as a
the L (odd) channels are supplied to the SPEAKER
Set the mixer’s LEVEL controls and MASTER LEVEL control to the minimum (zero).
synthesizer or CD player.
jack. The output level is adjusted with the MASTER
NOTE: The channel 7/8 input provides two sets of jacks—both phone jacks and RCA-pin jacks. Either one of these
jacks may be used, but not both at the same time. Please connect to only one of these jacks on each
channel.
LEVEL control. Used with the SPEAKER jack, this lets
º LEVEL meter
DI
3
Depending on the device used, set the MIC/LINE switch to MIC (
( ) as appropriate.
) or LINE
L
R
L
R
The LEVEL meter shows the level
L
R
L
R
L
For low-level signals (such as that of microphones), set the switch to the MIC ( ) position.
For high-level signals (such as keyboard instruments and audio equipment), set the switch to the
LINE ( ) position.
MIC
LINE
4
you output the signals in stereo from the speakers.
of the output signal from the
5 PHONES jack
SPEAKER jack.
This outputs the mixed signal channels from 1 to
! MIC/LINE switch
7/8, and the level is adjusted with the PHONES
Set this switch to MIC or LINE for channels 1, 2, depending on the level of the input signal. For low-level
control. Connect a set of headphones here.
signals (such as that of microphones), set the switch to the MIC (
R
Caution
MIC
LINE
Turning the power on
First, turn on the power to any connected devices, then turn the STAGEPAS 150M power on.
If you’ve connected powered speakers to the mixer, turn on the power of the mixer first, then the
powered speakers.
If the LIMITER flashes
continuously, the internal
power amplifier section is
being excessively
overloaded and may
malfunction. Reduce the
output level with the
MASTER LEVEL control so
that the indicator flashes
only briefly on the highest
transient peaks.
) position.
To avoid damage to speakers, be sure to turn off amplifiers (or powered speakers) before setting
These output the mixed signal channels from 1 to
Caution
this switch to MIC or LINE. We also recommend that you turn the MASTER LEVEL control to the
7/8, and the level is adjusted with the ST SUB OUT
minimum setting before operating the switch, to avoid excessively loud noises that could cause
control. You can use these jacks, for example, to
hearing loss or device damage.
connect a main mixer. These impedance balanced
jacks allow a longer cable to be connected with the
use of a balanced cable.
@ Equalizer
This lights when the POWER switch
is ON. When the indicator flashes,
the protection circuit is operating.
Check that the speaker cable is
correctly connected to the mixer
Caution
6 ST SUB OUT L (MONO) / R jacks
¡ POWER indicator
and reapply the power.
To avoid any loud, unexpected noise from the speakers, first turn on the power to those connected
devices that are closest to the sound source.
) position. For high-level signals (such
as keyboard instruments and audio equipment), set the switch to the LINE (
HIGH: Determines the level of the high frequency band for each channel. Rotating the knob
7 ST SUB OUT control
clockwise boosts the high frequencies and produces a clearer, crisper sound. If you start getting
Determines the signal level output from the ST SUB
feedback (a high-pitched squealing sound) or you want to make the sound softer and less harsh,
OUT jacks.
turn the knob counterclockwise slightly.
NOTE: The MASTER LEVEL control does not affect
the signal via the ST SUB OUT control.
LOW: Determines the level of the low frequency band for each channel. Rotating the knob
8 PHONES control
feedback or you want to make the sound less boomy, turn the knob counterclockwise slightly.
clockwise boosts the low frequencies and produces a deeper, warmer sound. If you start getting
Determines the signal level output from the
Example: Sound source (CD player or instrument) → STAGEPAS 150M → (Power amplifier)
When turning off the power to the system, reverse the order described above.
PHONES jack.
NOTE: The MASTER LEVEL control does not affect
the signal via the PHONES control.
5
Set the MASTER LEVEL control to the optimum position (indicated by the arrow).
Connection Example 2
Headphones
6
Main mixer
9
1
4
3
Instrument/device with stereo output
(synthesizer, etc.)
While playing your instrument or singing into the microphone, adjust the
LEVEL control of the corresponding channel.
CD Player
L
7
Included speaker
(300S)
2
L
R
!
R
8
º
Powered speaker
(Yamaha MSR100)
Microphone
Use the MASTER LEVEL control to adjust the overall volume.
Caution
6
5
Adjust the LEVEL Control of the corresponding channel so that the “0” LED lights up momentarily.
Electric
guitar
7
$
¡
*
L
R
#
(
L
R
L
R
L
R
L
^
R
L
Reverb recreates the warm ambience of an actual performance space, such as a concert hall or a
night club.
R
* CLICK switch
For each channel you want to apply reverb, set the corresponding REVERB
switch to ON ( ).
(for headphones)
Set this switch to ON to assign the
^ LEVEL control
click/metronome sounds to only the
PHONES jack when the CLICK switch
Use these controls to adjust the volume
balance among the various channels.
at the channel 5/6 is ON.
Caution
2
%
&
DI
1
@
Computer
If the LIMITER indicator flashes continuously, the internal power amplifier section is being
excessively overloaded and may malfunction.
Applying reverb or echo to the sound
)
( SPEECH/MUSIC switch
Use the REVERB control to adjust the overall reverb.
Set this switch to SPEECH (
) to optimize the
To reduce noise, set any LEVEL
controls on unused channels to
the minimum.
& MASTER LEVEL Control
Determines the volume of the signal output
mixer settings and sound quality for speech
from the SPEAKER jack. This allows you to
purposes and announcements.
adjust the overall volume without changing
Set this to MUSIC (
the relative volume balance among the
) to optimize the mixer for
musical performance. The switch lights up in
various channels (made with the LEVEL
yellow when it is set to MUSIC (
controls) or the tone settings (made with the
).
Equalizer).
OFF
ON
% CLICK switch
(for headphones/speaker)
# REVERB switch
Set this switch to ON to recreate the rich ambience
Set this switch to ON to assign the
of various performance environments, such as a
click (metronome) sounds that sent
concert hall or a night club. The switch lights up in
to the channel 5/6 to the PHONES
green when REVERB is ON (
).
jack, SPEAKER jack, and ST LINK
OUT R jack, but not to the ST SUB
$ REVERB control
OUT jacks.
Determines the overall level of the reverb or echo
Setting this switch to ON lets the
that is applied to the output signal. For best results,
player monitor the click (metronome)
this level should not be set very high, to avoid
sounds of a sequencer or a
possible feedback and to prevent the sound from
synthesizer.
becoming “muddy” with too much reverb.
Download PDF

advertising